[PATCH v6 7/8] ARM: dts: stm32: add Timers driver for stm32f429 MCU

[robh@kernel.org (Rob Herring)]

On Fri, Dec 09, 2016 at 03:15:18PM +0100, Benjamin Gaignard wrote:
> Add Timers and it sub-nodes into DT for stm32f429 family.
> 
> version 6:
> - split patch in two: one for SoC family and one for stm32f469
>   discovery board.
> 
> version 5:
> - rename gptimer node to timers
> - re-order timers node par addresses
> 
> version 4:
> - remove unwanted indexing in pwm@ and timer@ node name
> - use "reg" instead of additional parameters to set timer
>   configuration
> 
> version 3:
> - use "st,stm32-timer-trigger" in DT
> 
> version 2:
> - use parameters to describe hardware capabilities
> - do not use references for pwm and iio timer subnodes
> 
> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
> ---
>  arch/arm/boot/dts/stm32f429.dtsi | 275 +++++++++++++++++++++++++++++++++++++++
>  1 file changed, 275 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/stm32f429.dtsi b/arch/arm/boot/dts/stm32f429.dtsi
> index bca491d..d0fb9cc 100644
> --- a/arch/arm/boot/dts/stm32f429.dtsi
> +++ b/arch/arm/boot/dts/stm32f429.dtsi
> @@ -355,6 +355,21 @@
>  					slew-rate = <2>;
>  				};
>  			};
> +
> +			pwm1_pins: pwm at 1 {

No reg prop, so should not have a unit-address. Given the names in the 
define below, seems like "timer1" would be appropriate.

> +				pins {
> +					pinmux = <STM32F429_PA8_FUNC_TIM1_CH1>,
> +						 <STM32F429_PB13_FUNC_TIM1_CH1N>,
> +						 <STM32F429_PB12_FUNC_TIM1_BKIN>;
> +				};
> +			};
> +
> +			pwm3_pins: pwm at 3 {
> +				pins {
> +					pinmux = <STM32F429_PB4_FUNC_TIM3_CH1>,
> +						 <STM32F429_PB5_FUNC_TIM3_CH2>;
> +				};
> +			};
>  		};
>  
>  		rcc: rcc at 40023810 {
> @@ -426,6 +441,266 @@
>  			interrupts = <80>;
>  			clocks = <&rcc 0 38>;
>  		};
> +
> +		timers2: timers at 40000000 {

timer at ...

It may be more than just a timer, there's not a better generic name.

> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40000000 0x400>;
> +			clocks = <&rcc 0 128>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <1>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers3: timers at 40000400 {

ditto

> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40000400 0x400>;
> +			clocks = <&rcc 0 129>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <2>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers4: timers at 40000800 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40000800 0x400>;
> +			clocks = <&rcc 0 130>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <3>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers5: timers at 40000C00 {

timer at ...

And use lowercase hex.

> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40000C00 0x400>;

ditto

> +			clocks = <&rcc 0 131>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <4>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers6: timers at 40001000 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40001000 0x400>;
> +			clocks = <&rcc 0 132>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <5>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers7: timers at 40001400 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40001400 0x400>;
> +			clocks = <&rcc 0 133>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <6>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers12: timers at 40001800 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40001800 0x400>;
> +			clocks = <&rcc 0 134>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <9>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers13: timers at 40001C00 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40001C00 0x400>;
> +			clocks = <&rcc 0 135>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers14: timers at 40002000 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40002000 0x400>;
> +			clocks = <&rcc 0 136>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers1: timers at 40010000 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40010000 0x400>;
> +			clocks = <&rcc 0 160>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <0>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers8: timers at 40010400 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40010400 0x400>;
> +			clocks = <&rcc 0 161>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <7>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers9: timers at 40014000 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40014000 0x400>;
> +			clocks = <&rcc 0 176>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +
> +			timer {
> +				compatible = "st,stm32-timer-trigger";
> +				reg = <8>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers10: timers at 40014400 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40014400 0x400>;
> +			clocks = <&rcc 0 177>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +		};
> +
> +		timers11: timers at 40014800 {
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			compatible = "st,stm32-timers";
> +			reg = <0x40014800 0x400>;
> +			clocks = <&rcc 0 178>;
> +			clock-names = "clk_int";
> +			status = "disabled";
> +
> +			pwm {
> +				compatible = "st,stm32-pwm";
> +				status = "disabled";
> +			};
> +		};
>  	};
>  };
>  
> -- 
> 1.9.1
>