* [PATCH 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi
@ 2016-12-26 17:11 Icenowy Zheng
2016-12-26 17:11 ` [PATCH 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
2016-12-26 17:11 ` [PATCH 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
0 siblings, 2 replies; 4+ messages in thread
From: Icenowy Zheng @ 2016-12-26 17:11 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sun8i-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
On the way get rid of skeleton.dtsi, as recommended in that very file.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc , as well as pio and ccu's compatible]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm/boot/dts/sun8i-h3-h5.dtsi | 536 +++++++++++++++++++++++++++++++++++++
arch/arm/boot/dts/sun8i-h3.dtsi | 473 +-------------------------------
2 files changed, 543 insertions(+), 466 deletions(-)
create mode 100644 arch/arm/boot/dts/sun8i-h3-h5.dtsi
diff --git a/arch/arm/boot/dts/sun8i-h3-h5.dtsi b/arch/arm/boot/dts/sun8i-h3-h5.dtsi
new file mode 100644
index 000000000000..ecad824bc65d
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-h5.dtsi
@@ -0,0 +1,536 @@
+/*
+ * Copyright (C) 2015 Jens Kuske <jenskuske@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ osc24M: osc24M_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <24000000>;
+ clock-output-names = "osc24M";
+ };
+
+ osc32k: osc32k_clk {
+ #clock-cells = <0>;
+ compatible = "fixed-clock";
+ clock-frequency = <32768>;
+ clock-output-names = "osc32k";
+ };
+
+ apb0: apb0_clk {
+ compatible = "fixed-factor-clock";
+ #clock-cells = <0>;
+ clock-div = <1>;
+ clock-mult = <1>;
+ clocks = <&osc24M>;
+ clock-output-names = "apb0";
+ };
+
+ apb0_gates: clk at 01f01428 {
+ compatible = "allwinner,sun8i-h3-apb0-gates-clk",
+ "allwinner,sun4i-a10-gates-clk";
+ reg = <0x01f01428 0x4>;
+ #clock-cells = <1>;
+ clocks = <&apb0>;
+ clock-indices = <0>, <1>;
+ clock-output-names = "apb0_pio", "apb0_ir";
+ };
+
+ ir_clk: ir_clk at 01f01454 {
+ compatible = "allwinner,sun4i-a10-mod0-clk";
+ reg = <0x01f01454 0x4>;
+ #clock-cells = <0>;
+ clocks = <&osc32k>, <&osc24M>;
+ clock-output-names = "ir";
+ };
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ dma: dma-controller at 01c02000 {
+ compatible = "allwinner,sun8i-h3-dma";
+ reg = <0x01c02000 0x1000>;
+ interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_DMA>;
+ resets = <&ccu RST_BUS_DMA>;
+ #dma-cells = <1>;
+ };
+
+ mmc0: mmc at 01c0f000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c0f000 0x1000>;
+ resets = <&ccu RST_BUS_MMC0>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc1: mmc at 01c10000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c10000 0x1000>;
+ resets = <&ccu RST_BUS_MMC1>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mmc2: mmc at 01c11000 {
+ /* compatible and clocks are in per SoC .dtsi file */
+ reg = <0x01c11000 0x1000>;
+ resets = <&ccu RST_BUS_MMC2>;
+ reset-names = "ahb";
+ interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ usbphy: phy at 01c19400 {
+ compatible = "allwinner,sun8i-h3-usb-phy";
+ reg = <0x01c19400 0x2c>,
+ <0x01c1a800 0x4>,
+ <0x01c1b800 0x4>,
+ <0x01c1c800 0x4>,
+ <0x01c1d800 0x4>;
+ reg-names = "phy_ctrl",
+ "pmu0",
+ "pmu1",
+ "pmu2",
+ "pmu3";
+ clocks = <&ccu CLK_USB_PHY0>,
+ <&ccu CLK_USB_PHY1>,
+ <&ccu CLK_USB_PHY2>,
+ <&ccu CLK_USB_PHY3>;
+ clock-names = "usb0_phy",
+ "usb1_phy",
+ "usb2_phy",
+ "usb3_phy";
+ resets = <&ccu RST_USB_PHY0>,
+ <&ccu RST_USB_PHY1>,
+ <&ccu RST_USB_PHY2>,
+ <&ccu RST_USB_PHY3>;
+ reset-names = "usb0_reset",
+ "usb1_reset",
+ "usb2_reset",
+ "usb3_reset";
+ status = "disabled";
+ #phy-cells = <1>;
+ };
+
+ ehci1: usb at 01c1b000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1b000 0x100>;
+ interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci1: usb at 01c1b400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1b400 0x100>;
+ interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
+ <&ccu CLK_USB_OHCI1>;
+ resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
+ phys = <&usbphy 1>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci2: usb at 01c1c000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1c000 0x100>;
+ interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci2: usb at 01c1c400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1c400 0x100>;
+ interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
+ <&ccu CLK_USB_OHCI2>;
+ resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
+ phys = <&usbphy 2>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ehci3: usb at 01c1d000 {
+ compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
+ reg = <0x01c1d000 0x100>;
+ interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ohci3: usb at 01c1d400 {
+ compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
+ reg = <0x01c1d400 0x100>;
+ interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
+ <&ccu CLK_USB_OHCI3>;
+ resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
+ phys = <&usbphy 3>;
+ phy-names = "usb";
+ status = "disabled";
+ };
+
+ ccu: clock at 01c20000 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
+ pio: pinctrl at 01c20800 {
+ /* compatible is in per SoC .dtsi file */
+ reg = <0x01c20800 0x400>;
+ interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ i2c0_pins: i2c0 {
+ pins = "PA11", "PA12";
+ function = "i2c0";
+ };
+
+ i2c1_pins: i2c1 {
+ pins = "PA18", "PA19";
+ function = "i2c1";
+ };
+
+ i2c2_pins: i2c2 {
+ pins = "PE12", "PE13";
+ function = "i2c2";
+ };
+
+ mmc0_pins_a: mmc0 at 0 {
+ pins = "PF0", "PF1", "PF2", "PF3",
+ "PF4", "PF5";
+ function = "mmc0";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc0_cd_pin: mmc0_cd_pin at 0 {
+ pins = "PF6";
+ function = "gpio_in";
+ bias-pull-up;
+ };
+
+ mmc1_pins_a: mmc1 at 0 {
+ pins = "PG0", "PG1", "PG2", "PG3",
+ "PG4", "PG5";
+ function = "mmc1";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ mmc2_8bit_pins: mmc2_8bit {
+ pins = "PC5", "PC6", "PC8",
+ "PC9", "PC10", "PC11",
+ "PC12", "PC13", "PC14",
+ "PC15", "PC16";
+ function = "mmc2";
+ drive-strength = <30>;
+ bias-pull-up;
+ };
+
+ spi0_pins: spi0 {
+ pins = "PC0", "PC1", "PC2", "PC3";
+ function = "spi0";
+ };
+
+ spi1_pins: spi1 {
+ pins = "PA15", "PA16", "PA14", "PA13";
+ function = "spi1";
+ };
+
+ uart0_pins_a: uart0 at 0 {
+ pins = "PA4", "PA5";
+ function = "uart0";
+ };
+
+ uart1_pins: uart1 {
+ pins = "PG6", "PG7";
+ function = "uart1";
+ };
+
+ uart1_rts_cts_pins: uart1_rts_cts {
+ pins = "PG8", "PG9";
+ function = "uart1";
+ };
+
+ uart2_pins: uart2 {
+ pins = "PA0", "PA1";
+ function = "uart2";
+ };
+
+ uart3_pins: uart3 {
+ pins = "PA13", "PA14";
+ function = "uart3";
+ };
+ };
+
+ timer at 01c20c00 {
+ compatible = "allwinner,sun4i-a10-timer";
+ reg = <0x01c20c00 0xa0>;
+ interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&osc24M>;
+ };
+
+ spi0: spi at 01c68000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c68000 0x1000>;
+ interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 23>, <&dma 23>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi0_pins>;
+ resets = <&ccu RST_BUS_SPI0>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ spi1: spi at 01c69000 {
+ compatible = "allwinner,sun8i-h3-spi";
+ reg = <0x01c69000 0x1000>;
+ interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
+ clock-names = "ahb", "mod";
+ dmas = <&dma 24>, <&dma 24>;
+ dma-names = "rx", "tx";
+ pinctrl-names = "default";
+ pinctrl-0 = <&spi1_pins>;
+ resets = <&ccu RST_BUS_SPI1>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ wdt0: watchdog at 01c20ca0 {
+ compatible = "allwinner,sun6i-a31-wdt";
+ reg = <0x01c20ca0 0x20>;
+ interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ pwm: pwm at 01c21400 {
+ compatible = "allwinner,sun8i-h3-pwm";
+ reg = <0x01c21400 0x8>;
+ clocks = <&osc24M>;
+ #pwm-cells = <3>;
+ status = "disabled";
+ };
+
+ uart0: serial at 01c28000 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28000 0x400>;
+ interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART0>;
+ resets = <&ccu RST_BUS_UART0>;
+ dmas = <&dma 6>, <&dma 6>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart1: serial at 01c28400 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28400 0x400>;
+ interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART1>;
+ resets = <&ccu RST_BUS_UART1>;
+ dmas = <&dma 7>, <&dma 7>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart2: serial at 01c28800 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28800 0x400>;
+ interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART2>;
+ resets = <&ccu RST_BUS_UART2>;
+ dmas = <&dma 8>, <&dma 8>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ uart3: serial at 01c28c00 {
+ compatible = "snps,dw-apb-uart";
+ reg = <0x01c28c00 0x400>;
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ reg-shift = <2>;
+ reg-io-width = <4>;
+ clocks = <&ccu CLK_BUS_UART3>;
+ resets = <&ccu RST_BUS_UART3>;
+ dmas = <&dma 9>, <&dma 9>;
+ dma-names = "rx", "tx";
+ status = "disabled";
+ };
+
+ i2c0: i2c at 01c2ac00 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2ac00 0x400>;
+ interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C0>;
+ resets = <&ccu RST_BUS_I2C0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c1: i2c at 01c2b000 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C1>;
+ resets = <&ccu RST_BUS_I2C1>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c1_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ i2c2: i2c at 01c2b400 {
+ compatible = "allwinner,sun6i-a31-i2c";
+ reg = <0x01c2b000 0x400>;
+ interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&ccu CLK_BUS_I2C2>;
+ resets = <&ccu RST_BUS_I2C2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c2_pins>;
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ rtc: rtc at 01f00000 {
+ compatible = "allwinner,sun6i-a31-rtc";
+ reg = <0x01f00000 0x54>;
+ interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
+ };
+
+ apb0_reset: reset at 01f014b0 {
+ reg = <0x01f014b0 0x4>;
+ compatible = "allwinner,sun6i-a31-clock-reset";
+ #reset-cells = <1>;
+ };
+
+ ir: ir at 01f02000 {
+ compatible = "allwinner,sun5i-a13-ir";
+ clocks = <&apb0_gates 1>, <&ir_clk>;
+ clock-names = "apb", "ir";
+ resets = <&apb0_reset 1>;
+ interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
+ reg = <0x01f02000 0x40>;
+ status = "disabled";
+ };
+
+ r_pio: pinctrl at 01f02c00 {
+ compatible = "allwinner,sun8i-h3-r-pinctrl";
+ reg = <0x01f02c00 0x400>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
+ clock-names = "apb", "hosc", "losc";
+ resets = <&apb0_reset 0>;
+ gpio-controller;
+ #gpio-cells = <3>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+
+ ir_pins_a: ir at 0 {
+ pins = "PL11";
+ function = "s_cir_rx";
+ };
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi b/arch/arm/boot/dts/sun8i-h3.dtsi
index fe24cda6cb52..a454d2abd8ed 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -40,12 +40,9 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include "skeleton.dtsi"
-
#include <dt-bindings/clock/sun8i-h3-ccu.h>
-#include <dt-bindings/interrupt-controller/arm-gic.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
#include <dt-bindings/reset/sun8i-h3-ccu.h>
+#include "sun8i-h3-h5.dtsi"
/ {
interrupt-parent = <&gic>;
@@ -87,71 +84,9 @@
<GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
};
- clocks {
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- osc24M: osc24M_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <24000000>;
- clock-output-names = "osc24M";
- };
-
- osc32k: osc32k_clk {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <32768>;
- clock-output-names = "osc32k";
- };
-
- apb0: apb0_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "apb0";
- };
-
- apb0_gates: clk at 01f01428 {
- compatible = "allwinner,sun8i-h3-apb0-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01f01428 0x4>;
- #clock-cells = <1>;
- clocks = <&apb0>;
- clock-indices = <0>, <1>;
- clock-output-names = "apb0_pio", "apb0_ir";
- };
-
- ir_clk: ir_clk at 01f01454 {
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01f01454 0x4>;
- #clock-cells = <0>;
- clocks = <&osc32k>, <&osc24M>;
- clock-output-names = "ir";
- };
- };
-
soc {
- compatible = "simple-bus";
- #address-cells = <1>;
- #size-cells = <1>;
- ranges;
-
- dma: dma-controller at 01c02000 {
- compatible = "allwinner,sun8i-h3-dma";
- reg = <0x01c02000 0x1000>;
- interrupts = <GIC_SPI 50 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_DMA>;
- resets = <&ccu RST_BUS_DMA>;
- #dma-cells = <1>;
- };
-
- mmc0: mmc at 01c0f000 {
+ mmc at 01c0f000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c0f000 0x1000>;
clocks = <&ccu CLK_BUS_MMC0>,
<&ccu CLK_MMC0>,
<&ccu CLK_MMC0_OUTPUT>,
@@ -160,17 +95,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC0>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc1: mmc at 01c10000 {
+ mmc at 01c10000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c10000 0x1000>;
clocks = <&ccu CLK_BUS_MMC1>,
<&ccu CLK_MMC1>,
<&ccu CLK_MMC1_OUTPUT>,
@@ -179,17 +107,10 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC1>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
};
- mmc2: mmc at 01c11000 {
+ mmc at 01c11000 {
compatible = "allwinner,sun7i-a20-mmc";
- reg = <0x01c11000 0x1000>;
clocks = <&ccu CLK_BUS_MMC2>,
<&ccu CLK_MMC2>,
<&ccu CLK_MMC2_OUTPUT>,
@@ -198,217 +119,14 @@
"mmc",
"output",
"sample";
- resets = <&ccu RST_BUS_MMC2>;
- reset-names = "ahb";
- interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- usbphy: phy at 01c19400 {
- compatible = "allwinner,sun8i-h3-usb-phy";
- reg = <0x01c19400 0x2c>,
- <0x01c1a800 0x4>,
- <0x01c1b800 0x4>,
- <0x01c1c800 0x4>,
- <0x01c1d800 0x4>;
- reg-names = "phy_ctrl",
- "pmu0",
- "pmu1",
- "pmu2",
- "pmu3";
- clocks = <&ccu CLK_USB_PHY0>,
- <&ccu CLK_USB_PHY1>,
- <&ccu CLK_USB_PHY2>,
- <&ccu CLK_USB_PHY3>;
- clock-names = "usb0_phy",
- "usb1_phy",
- "usb2_phy",
- "usb3_phy";
- resets = <&ccu RST_USB_PHY0>,
- <&ccu RST_USB_PHY1>,
- <&ccu RST_USB_PHY2>,
- <&ccu RST_USB_PHY3>;
- reset-names = "usb0_reset",
- "usb1_reset",
- "usb2_reset",
- "usb3_reset";
- status = "disabled";
- #phy-cells = <1>;
};
- ehci1: usb at 01c1b000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1b000 0x100>;
- interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci1: usb at 01c1b400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1b400 0x100>;
- interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI1>, <&ccu CLK_BUS_OHCI1>,
- <&ccu CLK_USB_OHCI1>;
- resets = <&ccu RST_BUS_EHCI1>, <&ccu RST_BUS_OHCI1>;
- phys = <&usbphy 1>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci2: usb at 01c1c000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1c000 0x100>;
- interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci2: usb at 01c1c400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1c400 0x100>;
- interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI2>, <&ccu CLK_BUS_OHCI2>,
- <&ccu CLK_USB_OHCI2>;
- resets = <&ccu RST_BUS_EHCI2>, <&ccu RST_BUS_OHCI2>;
- phys = <&usbphy 2>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ehci3: usb at 01c1d000 {
- compatible = "allwinner,sun8i-h3-ehci", "generic-ehci";
- reg = <0x01c1d000 0x100>;
- interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ohci3: usb at 01c1d400 {
- compatible = "allwinner,sun8i-h3-ohci", "generic-ohci";
- reg = <0x01c1d400 0x100>;
- interrupts = <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_EHCI3>, <&ccu CLK_BUS_OHCI3>,
- <&ccu CLK_USB_OHCI3>;
- resets = <&ccu RST_BUS_EHCI3>, <&ccu RST_BUS_OHCI3>;
- phys = <&usbphy 3>;
- phy-names = "usb";
- status = "disabled";
- };
-
- ccu: clock at 01c20000 {
+ clock at 01c20000 {
compatible = "allwinner,sun8i-h3-ccu";
- reg = <0x01c20000 0x400>;
- clocks = <&osc24M>, <&osc32k>;
- clock-names = "hosc", "losc";
- #clock-cells = <1>;
- #reset-cells = <1>;
};
- pio: pinctrl at 01c20800 {
+ pinctrl at 01c20800 {
compatible = "allwinner,sun8i-h3-pinctrl";
- reg = <0x01c20800 0x400>;
- interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_PIO>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- i2c0_pins: i2c0 {
- pins = "PA11", "PA12";
- function = "i2c0";
- };
-
- i2c1_pins: i2c1 {
- pins = "PA18", "PA19";
- function = "i2c1";
- };
-
- i2c2_pins: i2c2 {
- pins = "PE12", "PE13";
- function = "i2c2";
- };
-
- mmc0_pins_a: mmc0 at 0 {
- pins = "PF0", "PF1", "PF2", "PF3",
- "PF4", "PF5";
- function = "mmc0";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc0_cd_pin: mmc0_cd_pin at 0 {
- pins = "PF6";
- function = "gpio_in";
- bias-pull-up;
- };
-
- mmc1_pins_a: mmc1 at 0 {
- pins = "PG0", "PG1", "PG2", "PG3",
- "PG4", "PG5";
- function = "mmc1";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- mmc2_8bit_pins: mmc2_8bit {
- pins = "PC5", "PC6", "PC8",
- "PC9", "PC10", "PC11",
- "PC12", "PC13", "PC14",
- "PC15", "PC16";
- function = "mmc2";
- drive-strength = <30>;
- bias-pull-up;
- };
-
- spi0_pins: spi0 {
- pins = "PC0", "PC1", "PC2", "PC3";
- function = "spi0";
- };
-
- spi1_pins: spi1 {
- pins = "PA15", "PA16", "PA14", "PA13";
- function = "spi1";
- };
-
- uart0_pins_a: uart0 at 0 {
- pins = "PA4", "PA5";
- function = "uart0";
- };
-
- uart1_pins: uart1 {
- pins = "PG6", "PG7";
- function = "uart1";
- };
-
- uart1_rts_cts_pins: uart1_rts_cts {
- pins = "PG8", "PG9";
- function = "uart1";
- };
-
- uart2_pins: uart2 {
- pins = "PA0", "PA1";
- function = "uart2";
- };
-
- uart3_pins: uart3 {
- pins = "PA13", "PA14";
- function = "uart3";
- };
};
timer at 01c20c00 {
@@ -419,143 +137,6 @@
clocks = <&osc24M>;
};
- spi0: spi at 01c68000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c68000 0x1000>;
- interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI0>, <&ccu CLK_SPI0>;
- clock-names = "ahb", "mod";
- dmas = <&dma 23>, <&dma 23>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi0_pins>;
- resets = <&ccu RST_BUS_SPI0>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- spi1: spi at 01c69000 {
- compatible = "allwinner,sun8i-h3-spi";
- reg = <0x01c69000 0x1000>;
- interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_SPI1>, <&ccu CLK_SPI1>;
- clock-names = "ahb", "mod";
- dmas = <&dma 24>, <&dma 24>;
- dma-names = "rx", "tx";
- pinctrl-names = "default";
- pinctrl-0 = <&spi1_pins>;
- resets = <&ccu RST_BUS_SPI1>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- wdt0: watchdog at 01c20ca0 {
- compatible = "allwinner,sun6i-a31-wdt";
- reg = <0x01c20ca0 0x20>;
- interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- pwm: pwm at 01c21400 {
- compatible = "allwinner,sun8i-h3-pwm";
- reg = <0x01c21400 0x8>;
- clocks = <&osc24M>;
- #pwm-cells = <3>;
- status = "disabled";
- };
-
- uart0: serial at 01c28000 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28000 0x400>;
- interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART0>;
- resets = <&ccu RST_BUS_UART0>;
- dmas = <&dma 6>, <&dma 6>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart1: serial at 01c28400 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28400 0x400>;
- interrupts = <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART1>;
- resets = <&ccu RST_BUS_UART1>;
- dmas = <&dma 7>, <&dma 7>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart2: serial at 01c28800 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28800 0x400>;
- interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART2>;
- resets = <&ccu RST_BUS_UART2>;
- dmas = <&dma 8>, <&dma 8>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- uart3: serial at 01c28c00 {
- compatible = "snps,dw-apb-uart";
- reg = <0x01c28c00 0x400>;
- interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
- reg-shift = <2>;
- reg-io-width = <4>;
- clocks = <&ccu CLK_BUS_UART3>;
- resets = <&ccu RST_BUS_UART3>;
- dmas = <&dma 9>, <&dma 9>;
- dma-names = "rx", "tx";
- status = "disabled";
- };
-
- i2c0: i2c at 01c2ac00 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2ac00 0x400>;
- interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C0>;
- resets = <&ccu RST_BUS_I2C0>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c0_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c1: i2c at 01c2b000 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C1>;
- resets = <&ccu RST_BUS_I2C1>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c1_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- i2c2: i2c at 01c2b400 {
- compatible = "allwinner,sun6i-a31-i2c";
- reg = <0x01c2b000 0x400>;
- interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&ccu CLK_BUS_I2C2>;
- resets = <&ccu RST_BUS_I2C2>;
- pinctrl-names = "default";
- pinctrl-0 = <&i2c2_pins>;
- status = "disabled";
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
gic: interrupt-controller at 01c81000 {
compatible = "arm,cortex-a7-gic", "arm,cortex-a15-gic";
reg = <0x01c81000 0x1000>,
@@ -566,46 +147,6 @@
#interrupt-cells = <3>;
interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
};
-
- rtc: rtc at 01f00000 {
- compatible = "allwinner,sun6i-a31-rtc";
- reg = <0x01f00000 0x54>;
- interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
- <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
- };
-
- apb0_reset: reset at 01f014b0 {
- reg = <0x01f014b0 0x4>;
- compatible = "allwinner,sun6i-a31-clock-reset";
- #reset-cells = <1>;
- };
-
- ir: ir at 01f02000 {
- compatible = "allwinner,sun5i-a13-ir";
- clocks = <&apb0_gates 1>, <&ir_clk>;
- clock-names = "apb", "ir";
- resets = <&apb0_reset 1>;
- interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>;
- reg = <0x01f02000 0x40>;
- status = "disabled";
- };
-
- r_pio: pinctrl at 01f02c00 {
- compatible = "allwinner,sun8i-h3-r-pinctrl";
- reg = <0x01f02c00 0x400>;
- interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
- clocks = <&apb0_gates 0>, <&osc24M>, <&osc32k>;
- clock-names = "apb", "hosc", "losc";
- resets = <&apb0_reset 0>;
- gpio-controller;
- #gpio-cells = <3>;
- interrupt-controller;
- #interrupt-cells = <3>;
-
- ir_pins_a: ir at 0 {
- pins = "PL11";
- function = "s_cir_rx";
- };
- };
};
};
+
--
2.11.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi
2016-12-26 17:11 [PATCH 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
@ 2016-12-26 17:11 ` Icenowy Zheng
2016-12-26 17:11 ` [PATCH 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
1 sibling, 0 replies; 4+ messages in thread
From: Icenowy Zheng @ 2016-12-26 17:11 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sun8i-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: remove H5 mmc compatible (seems equal to A64), add H5 pinctrl
compatible, and changes for my h3-h5 dtsi refactor, commit message
change to met new arm64 naming scheme]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi | 143 +++++++++++++++++++++++++
arch/arm64/boot/dts/allwinner/sun8i-h3-h5.dtsi | 1 +
2 files changed, 144 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
create mode 120000 arch/arm64/boot/dts/allwinner/sun8i-h3-h5.dtsi
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
new file mode 100644
index 000000000000..2cc372121f60
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5.dtsi
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include <dt-bindings/clock/sun50i-h5-ccu.h>
+#include <dt-bindings/reset/sun50i-h5-ccu.h>
+#include "sun8i-h3-h5.dtsi"
+
+/ {
+ interrupt-parent = <&gic>;
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <0>;
+ enable-method = "psci";
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <1>;
+ enable-method = "psci";
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <2>;
+ enable-method = "psci";
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a53", "arm,armv8";
+ device_type = "cpu";
+ reg = <3>;
+ enable-method = "psci";
+ };
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10
+ (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ mmc at 01c0f000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc at 01c10000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
+ };
+
+ mmc at 01c11000 {
+ compatible = "allwinner,sun50i-a64-mmc",
+ "allwinner,sun5i-a13-mmc";
+ clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
+ };
+
+ clock at 01c20000 {
+ compatible = "allwinner,sun50i-h5-ccu",
+ "allwinner,sun8i-h3-ccu";
+ };
+
+ pinctrl at 01c20800 {
+ compatible = "allwinner,sun50i-h5-pinctrl",
+ "allwinner,sun8i-h3-pinctrl";
+ };
+
+ gic: interrupt-controller at 1c81000 {
+ compatible = "arm,gic-400";
+ reg = <0x01c81000 0x1000>,
+ <0x01c82000 0x2000>,
+ <0x01c84000 0x2000>,
+ <0x01c86000 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
+ interrupt-controller;
+ #interrupt-cells = <3>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/allwinner/sun8i-h3-h5.dtsi b/arch/arm64/boot/dts/allwinner/sun8i-h3-h5.dtsi
new file mode 120000
index 000000000000..74f3ce9358a5
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun8i-h3-h5.dtsi
@@ -0,0 +1 @@
+../../../../arm/boot/dts/sun8i-h3-h5.dtsi
\ No newline at end of file
--
2.11.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2016-12-26 17:11 [PATCH 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
2016-12-26 17:11 ` [PATCH 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
@ 2016-12-26 17:11 ` Icenowy Zheng
2017-01-05 22:13 ` Maxime Ripard
1 sibling, 1 reply; 4+ messages in thread
From: Icenowy Zheng @ 2016-12-26 17:11 UTC (permalink / raw)
To: linux-arm-kernel
From: Andre Przywara <andre.przywara@arm.com>
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
---
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 183 +++++++++++++++++++++
2 files changed, 184 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
index 1e29a5ae8282..b26bb46b934c 100644
--- a/arch/arm64/boot/dts/allwinner/Makefile
+++ b/arch/arm64/boot/dts/allwinner/Makefile
@@ -1,4 +1,5 @@
dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
+dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
always := $(dtb-y)
subdir-y := $(dts-dirs)
diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
new file mode 100644
index 000000000000..a29ca6b274bb
--- /dev/null
+++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
@@ -0,0 +1,183 @@
+/*
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun50i-h5.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+ model = "Xunlong Orange Pi PC 2";
+ compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
+
+ reg_vcc3v3: vcc3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
+
+ pwr_led {
+ label = "orangepi:green:pwr";
+ gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+
+ status_led {
+ label = "orangepi:red:status";
+ gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ r_gpio_keys {
+ compatible = "gpio-keys";
+ pinctrl-names = "default";
+ pinctrl-0 = <&sw_r_opc>;
+
+ sw4 {
+ label = "sw4";
+ linux,code = <BTN_0>;
+ gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&ehci1 {
+ status = "okay";
+};
+
+&ehci2 {
+ status = "okay";
+};
+
+&ehci3 {
+ status = "okay";
+};
+
+&ir {
+ pinctrl-names = "default";
+ pinctrl-0 = <&ir_pins_a>;
+ status = "okay";
+};
+
+&mmc0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+ vmmc-supply = <®_vcc3v3>;
+ bus-width = <4>;
+ cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
+ cd-inverted;
+ status = "okay";
+};
+
+&ohci1 {
+ status = "okay";
+};
+
+&ohci2 {
+ status = "okay";
+};
+
+&ohci3 {
+ status = "okay";
+};
+
+&pio {
+ leds_opc: led_pins at 0 {
+ allwinner,pins = "PA15";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&r_pio {
+ leds_r_opc: led_pins at 0 {
+ allwinner,pins = "PL10";
+ allwinner,function = "gpio_out";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+
+ sw_r_opc: key_pins at 0 {
+ allwinner,pins = "PL3";
+ allwinner,function = "gpio_in";
+ allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+ allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+ };
+};
+
+&uart0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins_a>;
+ status = "okay";
+};
+
+&uart1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart1_pins>;
+};
+
+&uart2 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart2_pins>;
+};
+
+&usbphy {
+ /* USB VBUS is always on */
+ status = "okay";
+};
--
2.11.0
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board
2016-12-26 17:11 ` [PATCH 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
@ 2017-01-05 22:13 ` Maxime Ripard
0 siblings, 0 replies; 4+ messages in thread
From: Maxime Ripard @ 2017-01-05 22:13 UTC (permalink / raw)
To: linux-arm-kernel
On Tue, Dec 27, 2016 at 01:11:56AM +0800, Icenowy Zheng wrote:
> From: Andre Przywara <andre.przywara@arm.com>
>
> The Orange Pi PC 2 is a typical single board computer using the
> Allwinner H5 SoC. Apart from the usual suspects it features three
> separately driven USB ports and a Gigabit Ethernet port.
> Also it has a SPI NOR flash soldered, from which the board can boot
> from. This enables the SBC to behave like a "real computer" with
> built-in firmware.
>
> Add the board specific .dts file, which includes the H5 .dtsi and
> enables the peripherals that we support so far.
>
> Signed-off-by: Andre Przywara <andre.przywara@arm.com>
> Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
> ---
> arch/arm64/boot/dts/allwinner/Makefile | 1 +
> .../boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts | 183 +++++++++++++++++++++
> 2 files changed, 184 insertions(+)
> create mode 100644 arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
>
> diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile
> index 1e29a5ae8282..b26bb46b934c 100644
> --- a/arch/arm64/boot/dts/allwinner/Makefile
> +++ b/arch/arm64/boot/dts/allwinner/Makefile
> @@ -1,4 +1,5 @@
> dtb-$(CONFIG_ARCH_SUNXI) += sun50i-a64-pine64-plus.dtb sun50i-a64-pine64.dtb
> +dtb-$(CONFIG_ARCH_SUNXI) += sun50i-h5-orangepi-pc2.dtb
>
> always := $(dtb-y)
> subdir-y := $(dts-dirs)
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> new file mode 100644
> index 000000000000..a29ca6b274bb
> --- /dev/null
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h5-orangepi-pc2.dts
> @@ -0,0 +1,183 @@
> +/*
> + * Copyright (C) 2016 ARM Ltd.
> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + * a) This file is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation; either version 2 of the
> + * License, or (at your option) any later version.
> + *
> + * This file is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + * b) Permission is hereby granted, free of charge, to any person
> + * obtaining a copy of this software and associated documentation
> + * files (the "Software"), to deal in the Software without
> + * restriction, including without limitation the rights to use,
> + * copy, modify, merge, publish, distribute, sublicense, and/or
> + * sell copies of the Software, and to permit persons to whom the
> + * Software is furnished to do so, subject to the following
> + * conditions:
> + *
> + * The above copyright notice and this permission notice shall be
> + * included in all copies or substantial portions of the Software.
> + *
> + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + * OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun50i-h5.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> + model = "Xunlong Orange Pi PC 2";
> + compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5";
> +
> + reg_vcc3v3: vcc3v3 {
> + compatible = "regulator-fixed";
> + regulator-name = "vcc3v3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + };
> +
> + aliases {
> + serial0 = &uart0;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
There's no need to declare the LED GPIO in pinctrl.
> +
> + pwr_led {
> + label = "orangepi:green:pwr";
> + gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> + default-state = "on";
> + };
> +
> + status_led {
> + label = "orangepi:red:status";
> + gpios = <&pio 0 15 GPIO_ACTIVE_HIGH>;
> + };
> + };
> +
> + r_gpio_keys {
> + compatible = "gpio-keys";
> + pinctrl-names = "default";
> + pinctrl-0 = <&sw_r_opc>;
Ditto
> +
> + sw4 {
> + label = "sw4";
> + linux,code = <BTN_0>;
> + gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +&ehci1 {
> + status = "okay";
> +};
> +
> +&ehci2 {
> + status = "okay";
> +};
> +
> +&ehci3 {
> + status = "okay";
> +};
> +
> +&ir {
> + pinctrl-names = "default";
> + pinctrl-0 = <&ir_pins_a>;
> + status = "okay";
> +};
> +
> +&mmc0 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
Ditto
> + vmmc-supply = <®_vcc3v3>;
> + bus-width = <4>;
> + cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
> + cd-inverted;
Do you need both the GPIO flag and the cd-inverted one?
Thanks,
Maxime
--
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170105/59c73b72/attachment.sig>
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2017-01-05 22:13 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2016-12-26 17:11 [PATCH 4/6] arm: dts: sun8i: split Allwinner H3 .dtsi Icenowy Zheng
2016-12-26 17:11 ` [PATCH 5/6] arm64: dts: allwinner: add Allwinner H5 .dtsi Icenowy Zheng
2016-12-26 17:11 ` [PATCH 6/6] arm64: dts: sunxi: add support for the Orange Pi PC 2 board Icenowy Zheng
2017-01-05 22:13 ` Maxime Ripard
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox