* [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board
@ 2018-11-15 19:35 Andy Gross
2018-11-15 19:45 ` Bjorn Andersson
` (2 more replies)
0 siblings, 3 replies; 4+ messages in thread
From: Andy Gross @ 2018-11-15 19:35 UTC (permalink / raw)
To: linux-arm-kernel
This patch removes support for the APQ8064 based Arrow SD600 eval
board. This board was never sold publicly and had very limited
distribution. As such, we are removing this board and no longer
going to support it.
Signed-off-by: Andy Gross <andy.gross@linaro.org>
---
arch/arm/boot/dts/Makefile | 1 -
.../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 ---
.../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
3 files changed, 469 deletions(-)
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index b0e966d..00d6e65 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
ox820-cloudengines-pogoplug-series-3.dtb
dtb-$(CONFIG_ARCH_QCOM) += \
qcom-apq8060-dragonboard.dtb \
- qcom-apq8064-arrow-sd-600eval.dtb \
qcom-apq8064-cm-qs600.dtb \
qcom-apq8064-ifc6410.dtb \
qcom-apq8064-sony-xperia-yuga.dtb \
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
deleted file mode 100644
index 8df7315..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
+++ /dev/null
@@ -1,53 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-&tlmm_pinmux {
- card_detect: card-detect {
- mux {
- pins = "gpio26";
- function = "gpio";
- bias-disable;
- };
- };
-
- pcie_pins: pcie-pinmux {
- mux {
- pins = "gpio27";
- function = "gpio";
- };
- conf {
- pins = "gpio27";
- drive-strength = <12>;
- bias-disable;
- };
- };
-
- user_leds: user-leds {
- mux {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- };
-
- conf {
- pins = "gpio3", "gpio7", "gpio10", "gpio11";
- function = "gpio";
- output-low;
- };
- };
-
- magneto_pins: magneto-pins {
- mux {
- pins = "gpio31", "gpio48";
- function = "gpio";
- bias-disable;
- };
- };
-};
-
-&pm8921_mpps {
- mpp_leds: mpp-leds {
- pinconf {
- pins = "mpp7", "mpp8";
- function = "digital";
- output-low;
- };
- };
-};
diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
deleted file mode 100644
index 76b56ea..0000000
--- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
+++ /dev/null
@@ -1,415 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0
-#include "qcom-apq8064-v2.0.dtsi"
-#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/mfd/qcom-rpm.h>
-
-/ {
- model = "Arrow Electronics, APQ8064 SD_600eval";
- compatible = "arrow,sd_600eval", "qcom,apq8064";
-
- aliases {
- serial0 = &gsbi7_serial;
- serial1 = &gsbi1_serial;
- i2c0 = &gsbi2_i2c;
- i2c1 = &gsbi3_i2c;
- i2c2 = &gsbi4_i2c;
- i2c3 = &gsbi7_i2c;
- spi0 = &gsbi5_spi;
- };
-
- regulators {
- compatible = "simple-bus";
- vph: regulator-fixed at 1 {
- compatible = "regulator-fixed";
- regulator-min-microvolt = <4500000>;
- regulator-max-microvolt = <4500000>;
- regulator-name = "VPH";
- regulator-type = "voltage";
- regulator-boot-on;
- };
-
- /* on board fixed 3.3v supply */
- vcc3v3: vcc3v3 {
- compatible = "regulator-fixed";
- regulator-name = "VCC3V3";
- regulator-min-microvolt = <3300000>;
- regulator-max-microvolt = <3300000>;
- regulator-always-on;
- };
-
- };
-
- hdmi-out {
- compatible = "hdmi-connector";
- type = "a";
-
- port {
- hdmi_con: endpoint {
- remote-endpoint = <&hdmi_out>;
- };
- };
- };
-
- soc {
- rpm at 108000 {
- regulators {
- vdd_s1-supply = <&vph>;
- vdd_s2-supply = <&vph>;
- vdd_s3-supply = <&vph>;
- vdd_s4-supply = <&vph>;
- vdd_s5-supply = <&vph>;
- vdd_s6-supply = <&vph>;
- vdd_s7-supply = <&vph>;
- vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
- vdd_l3_l15_l17-supply = <&vph>;
- vdd_l4_l14-supply = <&vph>;
- vdd_l5_l8_l16-supply = <&vph>;
- vdd_l6_l7-supply = <&vph>;
- vdd_l9_l11-supply = <&vph>;
- vdd_l10_l22-supply = <&vph>;
- vdd_l21_l23_l29-supply = <&vph>;
- vdd_l24-supply = <&pm8921_s1>;
- vdd_l25-supply = <&pm8921_s1>;
- vdd_l26-supply = <&pm8921_s7>;
- vdd_l27-supply = <&pm8921_s7>;
- vdd_l28-supply = <&pm8921_s7>;
- vin_lvs1_3_6-supply = <&pm8921_s4>;
- vin_lvs2-supply = <&pm8921_s1>;
- vin_lvs4_5_7-supply = <&pm8921_s4>;
-
- s1 {
- regulator-always-on;
- regulator-min-microvolt = <1225000>;
- regulator-max-microvolt = <1225000>;
- qcom,switch-mode-frequency = <3200000>;
- bias-pull-down;
- };
-
- s2 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <1600000>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s3 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1400000>;
- qcom,switch-mode-frequency = <4800000>;
- };
-
- s4 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- qcom,switch-mode-frequency = <1600000>;
- qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
- bias-pull-down;
- regulator-always-on;
- };
-
- s7 {
- regulator-min-microvolt = <1300000>;
- regulator-max-microvolt = <1300000>;
- qcom,switch-mode-frequency = <3200000>;
- };
-
- l3 {
- regulator-min-microvolt = <3050000>;
- regulator-max-microvolt = <3300000>;
- bias-pull-down;
- };
-
- l4 {
- regulator-min-microvolt = <1000000>;
- regulator-max-microvolt = <1800000>;
- bias-pull-down;
- };
-
- l5 {
- regulator-min-microvolt = <2750000>;
- regulator-max-microvolt = <3000000>;
- bias-pull-down;
- regulator-boot-on;
- regulator-always-on;
- };
-
- l6 {
- regulator-min-microvolt = <2950000>;
- regulator-max-microvolt = <2950000>;
- bias-pull-down;
- };
-
- /**
- * 1.8v required on LS expansion
- * for mezzanine boards
- */
- l15 {
- regulator-min-microvolt = <1800000>;
- regulator-max-microvolt = <1800000>;
- regulator-always-on;
- };
-
- l23 {
- regulator-min-microvolt = <1700000>;
- regulator-max-microvolt = <1900000>;
- bias-pull-down;
- };
-
- lvs6 {
- bias-pull-down;
- };
-
- lvs7 {
- bias-pull-down;
- };
- };
- };
-
- gsbi at 12440000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_UART_W_FC>;
- serial at 12450000 {
- label = "LS-UART1";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi1_uart_4pins>;
- };
- };
-
- gsbi at 12480000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c at 124a0000 {
- /* On Low speed expansion and Sensors */
- label = "LS-I2C0";
- status = "okay";
- lis3mdl_mag at 1e {
- compatible = "st,lis3mdl-magn";
- reg = <0x1e>;
- vdd-supply = <&vcc3v3>;
- vddio-supply = <&pm8921_s4>;
- pinctrl-names = "default";
- pinctrl-0 = <&magneto_pins>;
- interrupt-parent = <&tlmm_pinmux>;
-
- st,drdy-int-pin = <2>;
- interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
- <31 IRQ_TYPE_EDGE_RISING>; /* INT */
- };
- };
- };
-
- gsbi at 16200000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c at 16280000 {
- /* On Low speed expansion */
- status = "okay";
- label = "LS-I2C1";
- clock-frequency = <200000>;
- eeprom at 52 {
- compatible = "atmel,24c128";
- reg = <0x52>;
- pagesize = <64>;
- };
- };
- };
-
- gsbi at 16300000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C>;
- i2c at 16380000 {
- /* On High speed expansion */
- label = "HS-CAM-I2C3";
- status = "okay";
- };
- };
-
- gsbi at 1a200000 {
- status = "okay";
- spi at 1a280000 {
- /* On Low speed expansion */
- label = "LS-SPI0";
- status = "okay";
- };
- };
-
- /* DEBUG UART */
- gsbi at 16600000 {
- status = "okay";
- qcom,mode = <GSBI_PROT_I2C_UART>;
- serial at 16640000 {
- label = "LS-UART0";
- status = "okay";
- pinctrl-names = "default";
- pinctrl-0 = <&gsbi7_uart_2pins>;
- };
-
- i2c at 16680000 {
- /* On High speed expansion */
- status = "okay";
- label = "HS-CAM-I2C2";
- };
- };
-
- leds {
- pinctrl-names = "default";
- pinctrl-0 = <&user_leds>, <&mpp_leds>;
-
- compatible = "gpio-leds";
-
- user-led0 {
- label = "user0-led";
- gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "heartbeat";
- default-state = "off";
- };
-
- user-led1 {
- label = "user1-led";
- gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc0";
- default-state = "off";
- };
-
- user-led2 {
- label = "user2-led";
- gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "mmc1";
- default-state = "off";
- };
-
- user-led3 {
- label = "user3-led";
- gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
- linux,default-trigger = "none";
- default-state = "off";
- };
-
- wifi-led {
- label = "WiFi-led";
- gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
-
- bt-led {
- label = "BT-led";
- gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
- default-state = "off";
- };
- };
-
- pci at 1b500000 {
- status = "okay";
- vdda-supply = <&pm8921_s3>;
- vdda_phy-supply = <&pm8921_lvs6>;
- vdda_refclk-supply = <&vcc3v3>;
- pinctrl-0 = <&pcie_pins>;
- pinctrl-names = "default";
- perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
- };
-
- phy at 1b400000 {
- status = "okay";
- };
-
- sata at 29000000 {
- status = "okay";
- target-supply = <&pm8921_lvs7>;
- };
-
- /* OTG */
- usb at 12500000 {
- status = "okay";
- dr_mode = "peripheral";
- ulpi {
- phy {
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l4>;
- };
- };
- };
-
- usb at 12520000 {
- status = "okay";
- dr_mode = "otg";
- ulpi {
- phy {
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
- };
- };
-
- usb at 12530000 {
- status = "okay";
- dr_mode = "otg";
- ulpi {
- phy {
- v3p3-supply = <&pm8921_l3>;
- v1p8-supply = <&pm8921_l23>;
- };
- };
- };
-
- amba {
- /* eMMC */
- sdcc at 12400000 {
- status = "okay";
- vmmc-supply = <&pm8921_l5>;
- vqmmc-supply = <&pm8921_s4>;
- };
-
- /* External micro SD card */
- sdcc at 12180000 {
- status = "okay";
- vmmc-supply = <&pm8921_l6>;
- pinctrl-names = "default";
- pinctrl-0 = <&card_detect>;
- cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
- };
- };
-
- riva-pil at 3204000 {
- status = "okay";
-
- pinctrl-names = "default";
- pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
- };
-
- hdmi-tx at 4a00000 {
- status = "okay";
- core-vdda-supply = <&pm8921_hdmi_switch>;
- hdmi-mux-supply = <&vcc3v3>;
-
- hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
-
- ports {
- port at 1 {
- endpoint {
- remote-endpoint = <&hdmi_con>;
- };
- };
- };
- };
-
- hdmi-phy at 4a00400 {
- status = "okay";
- core-vdda-supply = <&pm8921_hdmi_switch>;
- };
-
- mdp at 5100000 {
- status = "okay";
-
- ports {
- port at 3 {
- endpoint {
- remote-endpoint = <&hdmi_in>;
- };
- };
- };
- };
- };
-};
--
2.7.4
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board
2018-11-15 19:35 [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board Andy Gross
@ 2018-11-15 19:45 ` Bjorn Andersson
2018-11-18 22:32 ` Nicolas Dechesne
2018-11-18 23:29 ` Olof Johansson
2 siblings, 0 replies; 4+ messages in thread
From: Bjorn Andersson @ 2018-11-15 19:45 UTC (permalink / raw)
To: linux-arm-kernel
On Thu 15 Nov 11:35 PST 2018, Andy Gross wrote:
> This patch removes support for the APQ8064 based Arrow SD600 eval
> board. This board was never sold publicly and had very limited
> distribution. As such, we are removing this board and no longer
> going to support it.
>
> Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Regards,
Bjorn
> ---
> arch/arm/boot/dts/Makefile | 1 -
> .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 ---
> .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
> 3 files changed, 469 deletions(-)
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b0e966d..00d6e65 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
> ox820-cloudengines-pogoplug-series-3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += \
> qcom-apq8060-dragonboard.dtb \
> - qcom-apq8064-arrow-sd-600eval.dtb \
> qcom-apq8064-cm-qs600.dtb \
> qcom-apq8064-ifc6410.dtb \
> qcom-apq8064-sony-xperia-yuga.dtb \
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> deleted file mode 100644
> index 8df7315..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -&tlmm_pinmux {
> - card_detect: card-detect {
> - mux {
> - pins = "gpio26";
> - function = "gpio";
> - bias-disable;
> - };
> - };
> -
> - pcie_pins: pcie-pinmux {
> - mux {
> - pins = "gpio27";
> - function = "gpio";
> - };
> - conf {
> - pins = "gpio27";
> - drive-strength = <12>;
> - bias-disable;
> - };
> - };
> -
> - user_leds: user-leds {
> - mux {
> - pins = "gpio3", "gpio7", "gpio10", "gpio11";
> - function = "gpio";
> - };
> -
> - conf {
> - pins = "gpio3", "gpio7", "gpio10", "gpio11";
> - function = "gpio";
> - output-low;
> - };
> - };
> -
> - magneto_pins: magneto-pins {
> - mux {
> - pins = "gpio31", "gpio48";
> - function = "gpio";
> - bias-disable;
> - };
> - };
> -};
> -
> -&pm8921_mpps {
> - mpp_leds: mpp-leds {
> - pinconf {
> - pins = "mpp7", "mpp8";
> - function = "digital";
> - output-low;
> - };
> - };
> -};
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> deleted file mode 100644
> index 76b56ea..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> +++ /dev/null
> @@ -1,415 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -#include "qcom-apq8064-v2.0.dtsi"
> -#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/mfd/qcom-rpm.h>
> -
> -/ {
> - model = "Arrow Electronics, APQ8064 SD_600eval";
> - compatible = "arrow,sd_600eval", "qcom,apq8064";
> -
> - aliases {
> - serial0 = &gsbi7_serial;
> - serial1 = &gsbi1_serial;
> - i2c0 = &gsbi2_i2c;
> - i2c1 = &gsbi3_i2c;
> - i2c2 = &gsbi4_i2c;
> - i2c3 = &gsbi7_i2c;
> - spi0 = &gsbi5_spi;
> - };
> -
> - regulators {
> - compatible = "simple-bus";
> - vph: regulator-fixed at 1 {
> - compatible = "regulator-fixed";
> - regulator-min-microvolt = <4500000>;
> - regulator-max-microvolt = <4500000>;
> - regulator-name = "VPH";
> - regulator-type = "voltage";
> - regulator-boot-on;
> - };
> -
> - /* on board fixed 3.3v supply */
> - vcc3v3: vcc3v3 {
> - compatible = "regulator-fixed";
> - regulator-name = "VCC3V3";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - };
> -
> - hdmi-out {
> - compatible = "hdmi-connector";
> - type = "a";
> -
> - port {
> - hdmi_con: endpoint {
> - remote-endpoint = <&hdmi_out>;
> - };
> - };
> - };
> -
> - soc {
> - rpm at 108000 {
> - regulators {
> - vdd_s1-supply = <&vph>;
> - vdd_s2-supply = <&vph>;
> - vdd_s3-supply = <&vph>;
> - vdd_s4-supply = <&vph>;
> - vdd_s5-supply = <&vph>;
> - vdd_s6-supply = <&vph>;
> - vdd_s7-supply = <&vph>;
> - vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> - vdd_l3_l15_l17-supply = <&vph>;
> - vdd_l4_l14-supply = <&vph>;
> - vdd_l5_l8_l16-supply = <&vph>;
> - vdd_l6_l7-supply = <&vph>;
> - vdd_l9_l11-supply = <&vph>;
> - vdd_l10_l22-supply = <&vph>;
> - vdd_l21_l23_l29-supply = <&vph>;
> - vdd_l24-supply = <&pm8921_s1>;
> - vdd_l25-supply = <&pm8921_s1>;
> - vdd_l26-supply = <&pm8921_s7>;
> - vdd_l27-supply = <&pm8921_s7>;
> - vdd_l28-supply = <&pm8921_s7>;
> - vin_lvs1_3_6-supply = <&pm8921_s4>;
> - vin_lvs2-supply = <&pm8921_s1>;
> - vin_lvs4_5_7-supply = <&pm8921_s4>;
> -
> - s1 {
> - regulator-always-on;
> - regulator-min-microvolt = <1225000>;
> - regulator-max-microvolt = <1225000>;
> - qcom,switch-mode-frequency = <3200000>;
> - bias-pull-down;
> - };
> -
> - s2 {
> - regulator-min-microvolt = <1300000>;
> - regulator-max-microvolt = <1300000>;
> - qcom,switch-mode-frequency = <1600000>;
> - bias-pull-down;
> - regulator-always-on;
> - };
> -
> - s3 {
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1400000>;
> - qcom,switch-mode-frequency = <4800000>;
> - };
> -
> - s4 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - qcom,switch-mode-frequency = <1600000>;
> - qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
> - bias-pull-down;
> - regulator-always-on;
> - };
> -
> - s7 {
> - regulator-min-microvolt = <1300000>;
> - regulator-max-microvolt = <1300000>;
> - qcom,switch-mode-frequency = <3200000>;
> - };
> -
> - l3 {
> - regulator-min-microvolt = <3050000>;
> - regulator-max-microvolt = <3300000>;
> - bias-pull-down;
> - };
> -
> - l4 {
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1800000>;
> - bias-pull-down;
> - };
> -
> - l5 {
> - regulator-min-microvolt = <2750000>;
> - regulator-max-microvolt = <3000000>;
> - bias-pull-down;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - l6 {
> - regulator-min-microvolt = <2950000>;
> - regulator-max-microvolt = <2950000>;
> - bias-pull-down;
> - };
> -
> - /**
> - * 1.8v required on LS expansion
> - * for mezzanine boards
> - */
> - l15 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - l23 {
> - regulator-min-microvolt = <1700000>;
> - regulator-max-microvolt = <1900000>;
> - bias-pull-down;
> - };
> -
> - lvs6 {
> - bias-pull-down;
> - };
> -
> - lvs7 {
> - bias-pull-down;
> - };
> - };
> - };
> -
> - gsbi at 12440000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_UART_W_FC>;
> - serial at 12450000 {
> - label = "LS-UART1";
> - status = "okay";
> - pinctrl-names = "default";
> - pinctrl-0 = <&gsbi1_uart_4pins>;
> - };
> - };
> -
> - gsbi at 12480000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C>;
> - i2c at 124a0000 {
> - /* On Low speed expansion and Sensors */
> - label = "LS-I2C0";
> - status = "okay";
> - lis3mdl_mag at 1e {
> - compatible = "st,lis3mdl-magn";
> - reg = <0x1e>;
> - vdd-supply = <&vcc3v3>;
> - vddio-supply = <&pm8921_s4>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&magneto_pins>;
> - interrupt-parent = <&tlmm_pinmux>;
> -
> - st,drdy-int-pin = <2>;
> - interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
> - <31 IRQ_TYPE_EDGE_RISING>; /* INT */
> - };
> - };
> - };
> -
> - gsbi at 16200000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C>;
> - i2c at 16280000 {
> - /* On Low speed expansion */
> - status = "okay";
> - label = "LS-I2C1";
> - clock-frequency = <200000>;
> - eeprom at 52 {
> - compatible = "atmel,24c128";
> - reg = <0x52>;
> - pagesize = <64>;
> - };
> - };
> - };
> -
> - gsbi at 16300000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C>;
> - i2c at 16380000 {
> - /* On High speed expansion */
> - label = "HS-CAM-I2C3";
> - status = "okay";
> - };
> - };
> -
> - gsbi at 1a200000 {
> - status = "okay";
> - spi at 1a280000 {
> - /* On Low speed expansion */
> - label = "LS-SPI0";
> - status = "okay";
> - };
> - };
> -
> - /* DEBUG UART */
> - gsbi at 16600000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C_UART>;
> - serial at 16640000 {
> - label = "LS-UART0";
> - status = "okay";
> - pinctrl-names = "default";
> - pinctrl-0 = <&gsbi7_uart_2pins>;
> - };
> -
> - i2c at 16680000 {
> - /* On High speed expansion */
> - status = "okay";
> - label = "HS-CAM-I2C2";
> - };
> - };
> -
> - leds {
> - pinctrl-names = "default";
> - pinctrl-0 = <&user_leds>, <&mpp_leds>;
> -
> - compatible = "gpio-leds";
> -
> - user-led0 {
> - label = "user0-led";
> - gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "heartbeat";
> - default-state = "off";
> - };
> -
> - user-led1 {
> - label = "user1-led";
> - gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "mmc0";
> - default-state = "off";
> - };
> -
> - user-led2 {
> - label = "user2-led";
> - gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "mmc1";
> - default-state = "off";
> - };
> -
> - user-led3 {
> - label = "user3-led";
> - gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "none";
> - default-state = "off";
> - };
> -
> - wifi-led {
> - label = "WiFi-led";
> - gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
> - default-state = "off";
> - };
> -
> - bt-led {
> - label = "BT-led";
> - gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
> - default-state = "off";
> - };
> - };
> -
> - pci at 1b500000 {
> - status = "okay";
> - vdda-supply = <&pm8921_s3>;
> - vdda_phy-supply = <&pm8921_lvs6>;
> - vdda_refclk-supply = <&vcc3v3>;
> - pinctrl-0 = <&pcie_pins>;
> - pinctrl-names = "default";
> - perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
> - };
> -
> - phy at 1b400000 {
> - status = "okay";
> - };
> -
> - sata at 29000000 {
> - status = "okay";
> - target-supply = <&pm8921_lvs7>;
> - };
> -
> - /* OTG */
> - usb at 12500000 {
> - status = "okay";
> - dr_mode = "peripheral";
> - ulpi {
> - phy {
> - v3p3-supply = <&pm8921_l3>;
> - v1p8-supply = <&pm8921_l4>;
> - };
> - };
> - };
> -
> - usb at 12520000 {
> - status = "okay";
> - dr_mode = "otg";
> - ulpi {
> - phy {
> - v3p3-supply = <&pm8921_l3>;
> - v1p8-supply = <&pm8921_l23>;
> - };
> - };
> - };
> -
> - usb at 12530000 {
> - status = "okay";
> - dr_mode = "otg";
> - ulpi {
> - phy {
> - v3p3-supply = <&pm8921_l3>;
> - v1p8-supply = <&pm8921_l23>;
> - };
> - };
> - };
> -
> - amba {
> - /* eMMC */
> - sdcc at 12400000 {
> - status = "okay";
> - vmmc-supply = <&pm8921_l5>;
> - vqmmc-supply = <&pm8921_s4>;
> - };
> -
> - /* External micro SD card */
> - sdcc at 12180000 {
> - status = "okay";
> - vmmc-supply = <&pm8921_l6>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&card_detect>;
> - cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
> - };
> - };
> -
> - riva-pil at 3204000 {
> - status = "okay";
> -
> - pinctrl-names = "default";
> - pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
> - };
> -
> - hdmi-tx at 4a00000 {
> - status = "okay";
> - core-vdda-supply = <&pm8921_hdmi_switch>;
> - hdmi-mux-supply = <&vcc3v3>;
> -
> - hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
> -
> - ports {
> - port at 1 {
> - endpoint {
> - remote-endpoint = <&hdmi_con>;
> - };
> - };
> - };
> - };
> -
> - hdmi-phy at 4a00400 {
> - status = "okay";
> - core-vdda-supply = <&pm8921_hdmi_switch>;
> - };
> -
> - mdp at 5100000 {
> - status = "okay";
> -
> - ports {
> - port at 3 {
> - endpoint {
> - remote-endpoint = <&hdmi_in>;
> - };
> - };
> - };
> - };
> - };
> -};
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 4+ messages in thread* [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board
2018-11-15 19:35 [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board Andy Gross
2018-11-15 19:45 ` Bjorn Andersson
@ 2018-11-18 22:32 ` Nicolas Dechesne
2018-11-18 23:29 ` Olof Johansson
2 siblings, 0 replies; 4+ messages in thread
From: Nicolas Dechesne @ 2018-11-18 22:32 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Nov 15, 2018 at 8:35 PM Andy Gross <andy.gross@linaro.org> wrote:
>
> This patch removes support for the APQ8064 based Arrow SD600 eval
> board. This board was never sold publicly and had very limited
> distribution. As such, we are removing this board and no longer
> going to support it.
>
> Signed-off-by: Andy Gross <andy.gross@linaro.org>
Reviewed-by: Nicolas Dechesne <nicolas.dechesne@linaro.org>
> ---
> arch/arm/boot/dts/Makefile | 1 -
> .../dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi | 53 ---
> .../arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts | 415 ---------------------
> 3 files changed, 469 deletions(-)
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> delete mode 100644 arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index b0e966d..00d6e65 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -783,7 +783,6 @@ dtb-$(CONFIG_ARCH_OXNAS) += \
> ox820-cloudengines-pogoplug-series-3.dtb
> dtb-$(CONFIG_ARCH_QCOM) += \
> qcom-apq8060-dragonboard.dtb \
> - qcom-apq8064-arrow-sd-600eval.dtb \
> qcom-apq8064-cm-qs600.dtb \
> qcom-apq8064-ifc6410.dtb \
> qcom-apq8064-sony-xperia-yuga.dtb \
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> deleted file mode 100644
> index 8df7315..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval-pins.dtsi
> +++ /dev/null
> @@ -1,53 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -&tlmm_pinmux {
> - card_detect: card-detect {
> - mux {
> - pins = "gpio26";
> - function = "gpio";
> - bias-disable;
> - };
> - };
> -
> - pcie_pins: pcie-pinmux {
> - mux {
> - pins = "gpio27";
> - function = "gpio";
> - };
> - conf {
> - pins = "gpio27";
> - drive-strength = <12>;
> - bias-disable;
> - };
> - };
> -
> - user_leds: user-leds {
> - mux {
> - pins = "gpio3", "gpio7", "gpio10", "gpio11";
> - function = "gpio";
> - };
> -
> - conf {
> - pins = "gpio3", "gpio7", "gpio10", "gpio11";
> - function = "gpio";
> - output-low;
> - };
> - };
> -
> - magneto_pins: magneto-pins {
> - mux {
> - pins = "gpio31", "gpio48";
> - function = "gpio";
> - bias-disable;
> - };
> - };
> -};
> -
> -&pm8921_mpps {
> - mpp_leds: mpp-leds {
> - pinconf {
> - pins = "mpp7", "mpp8";
> - function = "digital";
> - output-low;
> - };
> - };
> -};
> diff --git a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts b/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> deleted file mode 100644
> index 76b56ea..0000000
> --- a/arch/arm/boot/dts/qcom-apq8064-arrow-sd-600eval.dts
> +++ /dev/null
> @@ -1,415 +0,0 @@
> -// SPDX-License-Identifier: GPL-2.0
> -#include "qcom-apq8064-v2.0.dtsi"
> -#include "qcom-apq8064-arrow-sd-600eval-pins.dtsi"
> -#include <dt-bindings/gpio/gpio.h>
> -#include <dt-bindings/mfd/qcom-rpm.h>
> -
> -/ {
> - model = "Arrow Electronics, APQ8064 SD_600eval";
> - compatible = "arrow,sd_600eval", "qcom,apq8064";
> -
> - aliases {
> - serial0 = &gsbi7_serial;
> - serial1 = &gsbi1_serial;
> - i2c0 = &gsbi2_i2c;
> - i2c1 = &gsbi3_i2c;
> - i2c2 = &gsbi4_i2c;
> - i2c3 = &gsbi7_i2c;
> - spi0 = &gsbi5_spi;
> - };
> -
> - regulators {
> - compatible = "simple-bus";
> - vph: regulator-fixed at 1 {
> - compatible = "regulator-fixed";
> - regulator-min-microvolt = <4500000>;
> - regulator-max-microvolt = <4500000>;
> - regulator-name = "VPH";
> - regulator-type = "voltage";
> - regulator-boot-on;
> - };
> -
> - /* on board fixed 3.3v supply */
> - vcc3v3: vcc3v3 {
> - compatible = "regulator-fixed";
> - regulator-name = "VCC3V3";
> - regulator-min-microvolt = <3300000>;
> - regulator-max-microvolt = <3300000>;
> - regulator-always-on;
> - };
> -
> - };
> -
> - hdmi-out {
> - compatible = "hdmi-connector";
> - type = "a";
> -
> - port {
> - hdmi_con: endpoint {
> - remote-endpoint = <&hdmi_out>;
> - };
> - };
> - };
> -
> - soc {
> - rpm at 108000 {
> - regulators {
> - vdd_s1-supply = <&vph>;
> - vdd_s2-supply = <&vph>;
> - vdd_s3-supply = <&vph>;
> - vdd_s4-supply = <&vph>;
> - vdd_s5-supply = <&vph>;
> - vdd_s6-supply = <&vph>;
> - vdd_s7-supply = <&vph>;
> - vdd_l1_l2_l12_l18-supply = <&pm8921_s4>;
> - vdd_l3_l15_l17-supply = <&vph>;
> - vdd_l4_l14-supply = <&vph>;
> - vdd_l5_l8_l16-supply = <&vph>;
> - vdd_l6_l7-supply = <&vph>;
> - vdd_l9_l11-supply = <&vph>;
> - vdd_l10_l22-supply = <&vph>;
> - vdd_l21_l23_l29-supply = <&vph>;
> - vdd_l24-supply = <&pm8921_s1>;
> - vdd_l25-supply = <&pm8921_s1>;
> - vdd_l26-supply = <&pm8921_s7>;
> - vdd_l27-supply = <&pm8921_s7>;
> - vdd_l28-supply = <&pm8921_s7>;
> - vin_lvs1_3_6-supply = <&pm8921_s4>;
> - vin_lvs2-supply = <&pm8921_s1>;
> - vin_lvs4_5_7-supply = <&pm8921_s4>;
> -
> - s1 {
> - regulator-always-on;
> - regulator-min-microvolt = <1225000>;
> - regulator-max-microvolt = <1225000>;
> - qcom,switch-mode-frequency = <3200000>;
> - bias-pull-down;
> - };
> -
> - s2 {
> - regulator-min-microvolt = <1300000>;
> - regulator-max-microvolt = <1300000>;
> - qcom,switch-mode-frequency = <1600000>;
> - bias-pull-down;
> - regulator-always-on;
> - };
> -
> - s3 {
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1400000>;
> - qcom,switch-mode-frequency = <4800000>;
> - };
> -
> - s4 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - qcom,switch-mode-frequency = <1600000>;
> - qcom,force-mode = <QCOM_RPM_FORCE_MODE_AUTO>;
> - bias-pull-down;
> - regulator-always-on;
> - };
> -
> - s7 {
> - regulator-min-microvolt = <1300000>;
> - regulator-max-microvolt = <1300000>;
> - qcom,switch-mode-frequency = <3200000>;
> - };
> -
> - l3 {
> - regulator-min-microvolt = <3050000>;
> - regulator-max-microvolt = <3300000>;
> - bias-pull-down;
> - };
> -
> - l4 {
> - regulator-min-microvolt = <1000000>;
> - regulator-max-microvolt = <1800000>;
> - bias-pull-down;
> - };
> -
> - l5 {
> - regulator-min-microvolt = <2750000>;
> - regulator-max-microvolt = <3000000>;
> - bias-pull-down;
> - regulator-boot-on;
> - regulator-always-on;
> - };
> -
> - l6 {
> - regulator-min-microvolt = <2950000>;
> - regulator-max-microvolt = <2950000>;
> - bias-pull-down;
> - };
> -
> - /**
> - * 1.8v required on LS expansion
> - * for mezzanine boards
> - */
> - l15 {
> - regulator-min-microvolt = <1800000>;
> - regulator-max-microvolt = <1800000>;
> - regulator-always-on;
> - };
> -
> - l23 {
> - regulator-min-microvolt = <1700000>;
> - regulator-max-microvolt = <1900000>;
> - bias-pull-down;
> - };
> -
> - lvs6 {
> - bias-pull-down;
> - };
> -
> - lvs7 {
> - bias-pull-down;
> - };
> - };
> - };
> -
> - gsbi at 12440000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_UART_W_FC>;
> - serial at 12450000 {
> - label = "LS-UART1";
> - status = "okay";
> - pinctrl-names = "default";
> - pinctrl-0 = <&gsbi1_uart_4pins>;
> - };
> - };
> -
> - gsbi at 12480000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C>;
> - i2c at 124a0000 {
> - /* On Low speed expansion and Sensors */
> - label = "LS-I2C0";
> - status = "okay";
> - lis3mdl_mag at 1e {
> - compatible = "st,lis3mdl-magn";
> - reg = <0x1e>;
> - vdd-supply = <&vcc3v3>;
> - vddio-supply = <&pm8921_s4>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&magneto_pins>;
> - interrupt-parent = <&tlmm_pinmux>;
> -
> - st,drdy-int-pin = <2>;
> - interrupts = <48 IRQ_TYPE_EDGE_RISING>, /* DRDY line */
> - <31 IRQ_TYPE_EDGE_RISING>; /* INT */
> - };
> - };
> - };
> -
> - gsbi at 16200000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C>;
> - i2c at 16280000 {
> - /* On Low speed expansion */
> - status = "okay";
> - label = "LS-I2C1";
> - clock-frequency = <200000>;
> - eeprom at 52 {
> - compatible = "atmel,24c128";
> - reg = <0x52>;
> - pagesize = <64>;
> - };
> - };
> - };
> -
> - gsbi at 16300000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C>;
> - i2c at 16380000 {
> - /* On High speed expansion */
> - label = "HS-CAM-I2C3";
> - status = "okay";
> - };
> - };
> -
> - gsbi at 1a200000 {
> - status = "okay";
> - spi at 1a280000 {
> - /* On Low speed expansion */
> - label = "LS-SPI0";
> - status = "okay";
> - };
> - };
> -
> - /* DEBUG UART */
> - gsbi at 16600000 {
> - status = "okay";
> - qcom,mode = <GSBI_PROT_I2C_UART>;
> - serial at 16640000 {
> - label = "LS-UART0";
> - status = "okay";
> - pinctrl-names = "default";
> - pinctrl-0 = <&gsbi7_uart_2pins>;
> - };
> -
> - i2c at 16680000 {
> - /* On High speed expansion */
> - status = "okay";
> - label = "HS-CAM-I2C2";
> - };
> - };
> -
> - leds {
> - pinctrl-names = "default";
> - pinctrl-0 = <&user_leds>, <&mpp_leds>;
> -
> - compatible = "gpio-leds";
> -
> - user-led0 {
> - label = "user0-led";
> - gpios = <&tlmm_pinmux 3 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "heartbeat";
> - default-state = "off";
> - };
> -
> - user-led1 {
> - label = "user1-led";
> - gpios = <&tlmm_pinmux 7 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "mmc0";
> - default-state = "off";
> - };
> -
> - user-led2 {
> - label = "user2-led";
> - gpios = <&tlmm_pinmux 10 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "mmc1";
> - default-state = "off";
> - };
> -
> - user-led3 {
> - label = "user3-led";
> - gpios = <&tlmm_pinmux 11 GPIO_ACTIVE_HIGH>;
> - linux,default-trigger = "none";
> - default-state = "off";
> - };
> -
> - wifi-led {
> - label = "WiFi-led";
> - gpios = <&pm8921_mpps 7 GPIO_ACTIVE_HIGH>;
> - default-state = "off";
> - };
> -
> - bt-led {
> - label = "BT-led";
> - gpios = <&pm8921_mpps 8 GPIO_ACTIVE_HIGH>;
> - default-state = "off";
> - };
> - };
> -
> - pci at 1b500000 {
> - status = "okay";
> - vdda-supply = <&pm8921_s3>;
> - vdda_phy-supply = <&pm8921_lvs6>;
> - vdda_refclk-supply = <&vcc3v3>;
> - pinctrl-0 = <&pcie_pins>;
> - pinctrl-names = "default";
> - perst-gpio = <&tlmm_pinmux 27 GPIO_ACTIVE_LOW>;
> - };
> -
> - phy at 1b400000 {
> - status = "okay";
> - };
> -
> - sata at 29000000 {
> - status = "okay";
> - target-supply = <&pm8921_lvs7>;
> - };
> -
> - /* OTG */
> - usb at 12500000 {
> - status = "okay";
> - dr_mode = "peripheral";
> - ulpi {
> - phy {
> - v3p3-supply = <&pm8921_l3>;
> - v1p8-supply = <&pm8921_l4>;
> - };
> - };
> - };
> -
> - usb at 12520000 {
> - status = "okay";
> - dr_mode = "otg";
> - ulpi {
> - phy {
> - v3p3-supply = <&pm8921_l3>;
> - v1p8-supply = <&pm8921_l23>;
> - };
> - };
> - };
> -
> - usb at 12530000 {
> - status = "okay";
> - dr_mode = "otg";
> - ulpi {
> - phy {
> - v3p3-supply = <&pm8921_l3>;
> - v1p8-supply = <&pm8921_l23>;
> - };
> - };
> - };
> -
> - amba {
> - /* eMMC */
> - sdcc at 12400000 {
> - status = "okay";
> - vmmc-supply = <&pm8921_l5>;
> - vqmmc-supply = <&pm8921_s4>;
> - };
> -
> - /* External micro SD card */
> - sdcc at 12180000 {
> - status = "okay";
> - vmmc-supply = <&pm8921_l6>;
> - pinctrl-names = "default";
> - pinctrl-0 = <&card_detect>;
> - cd-gpios = <&tlmm_pinmux 26 GPIO_ACTIVE_HIGH>;
> - };
> - };
> -
> - riva-pil at 3204000 {
> - status = "okay";
> -
> - pinctrl-names = "default";
> - pinctrl-0 = <&riva_wlan_pin_a>, <&riva_bt_pin_a>, <&riva_fm_pin_a>;
> - };
> -
> - hdmi-tx at 4a00000 {
> - status = "okay";
> - core-vdda-supply = <&pm8921_hdmi_switch>;
> - hdmi-mux-supply = <&vcc3v3>;
> -
> - hpd-gpio = <&tlmm_pinmux 72 GPIO_ACTIVE_HIGH>;
> -
> - ports {
> - port at 1 {
> - endpoint {
> - remote-endpoint = <&hdmi_con>;
> - };
> - };
> - };
> - };
> -
> - hdmi-phy at 4a00400 {
> - status = "okay";
> - core-vdda-supply = <&pm8921_hdmi_switch>;
> - };
> -
> - mdp at 5100000 {
> - status = "okay";
> -
> - ports {
> - port at 3 {
> - endpoint {
> - remote-endpoint = <&hdmi_in>;
> - };
> - };
> - };
> - };
> - };
> -};
> --
> 2.7.4
>
^ permalink raw reply [flat|nested] 4+ messages in thread* [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board
2018-11-15 19:35 [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board Andy Gross
2018-11-15 19:45 ` Bjorn Andersson
2018-11-18 22:32 ` Nicolas Dechesne
@ 2018-11-18 23:29 ` Olof Johansson
2 siblings, 0 replies; 4+ messages in thread
From: Olof Johansson @ 2018-11-18 23:29 UTC (permalink / raw)
To: linux-arm-kernel
On Thu, Nov 15, 2018 at 11:35 AM Andy Gross <andy.gross@linaro.org> wrote:
>
> This patch removes support for the APQ8064 based Arrow SD600 eval
> board. This board was never sold publicly and had very limited
> distribution. As such, we are removing this board and no longer
> going to support it.
>
> Signed-off-by: Andy Gross <andy.gross@linaro.org>
It's currently throwing DTS warnings as well, so if nobody's
interested in keeping it around, this seems OK with me.
Acked-by: Olof Johansson <olof@lixom.net>
-Olof
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2018-11-18 23:29 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2018-11-15 19:35 [PATCH] ARM: dts: qcom: Remove Arrow SD600 eval board Andy Gross
2018-11-15 19:45 ` Bjorn Andersson
2018-11-18 22:32 ` Nicolas Dechesne
2018-11-18 23:29 ` Olof Johansson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox