[PATCH v2 3/3] arm64: dts: ti: k3-j7200-som-p0: Add nodes for OSPI0

From: Pratyush Yadav <p.yadav@ti.com>
To: Nishanth Menon <nm@ti.com>, Tero Kristo <kristo@kernel.org>,
	Rob Herring <robh+dt@kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Cc: Pratyush Yadav <p.yadav@ti.com>, Vignesh Raghavendra <vigneshr@ti.com>
Subject: [PATCH v2 3/3] arm64: dts: ti: k3-j7200-som-p0: Add nodes for OSPI0
Date: Fri, 5 Mar 2021 21:09:26 +0530	[thread overview]
Message-ID: <20210305153926.3479-4-p.yadav@ti.com> (raw)
In-Reply-To: <20210305153926.3479-1-p.yadav@ti.com>

TI J7200 has the Cadence OSPI controller for interfacing with OSPI
flashes. Add its node to allow using SPI flashes.

Signed-off-by: Pratyush Yadav <p.yadav@ti.com>
---

Notes:
    Changes in v2:
    - Do not force a pulldown on the DQS line because it already has a
      pulldown resistor.

 .../boot/dts/ti/k3-j7200-mcu-wakeup.dtsi      | 17 +++++++++
 arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi   | 36 +++++++++++++++++++
 2 files changed, 53 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
index 359e3e8a8cd0..5408ec815d58 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-mcu-wakeup.dtsi
@@ -269,6 +269,23 @@ hbmc: hyperbus@47034000 {
 			#size-cells = <1>;
 			mux-controls = <&hbmc_mux 0>;
 		};
+
+		ospi0: spi@47040000 {
+			compatible = "ti,am654-ospi";
+			reg = <0x0 0x47040000 0x0 0x100>,
+			      <0x5 0x00000000 0x1 0x0000000>;
+			interrupts = <GIC_SPI 840 IRQ_TYPE_LEVEL_HIGH>;
+			cdns,fifo-depth = <256>;
+			cdns,fifo-width = <4>;
+			cdns,trigger-address = <0x0>;
+			clocks = <&k3_clks 103 0>;
+			assigned-clocks = <&k3_clks 103 0>;
+			assigned-clock-parents = <&k3_clks 103 2>;
+			assigned-clock-rates = <166666666>;
+			power-domains = <&k3_pds 103 TI_SCI_PD_EXCLUSIVE>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
 	};
 
 	tscadc0: tscadc@40200000 {
diff --git a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
index a988e2ab2ba1..34724440171a 100644
--- a/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j7200-som-p0.dtsi
@@ -100,6 +100,22 @@ J721E_WKUP_IOPAD(0x24, PIN_INPUT, 1) /* (A8) MCU_OSPI0_D6.MCU_HYPERBUS0_DQ6 */
 			J721E_WKUP_IOPAD(0x28, PIN_INPUT, 1) /* (A7) MCU_OSPI0_D7.MCU_HYPERBUS0_DQ7 */
 		>;
 	};
+
+	mcu_fss0_ospi0_pins_default: mcu-fss0-ospi0-pins-default {
+		pinctrl-single,pins = <
+			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_OSPI0_CLK */
+			J721E_WKUP_IOPAD(0x002c, PIN_OUTPUT, 0) /* MCU_OSPI0_CSn0 */
+			J721E_WKUP_IOPAD(0x000c, PIN_INPUT, 0)  /* MCU_OSPI0_D0 */
+			J721E_WKUP_IOPAD(0x0010, PIN_INPUT, 0)  /* MCU_OSPI0_D1 */
+			J721E_WKUP_IOPAD(0x0014, PIN_INPUT, 0)  /* MCU_OSPI0_D2 */
+			J721E_WKUP_IOPAD(0x0018, PIN_INPUT, 0)  /* MCU_OSPI0_D3 */
+			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0)  /* MCU_OSPI0_D4 */
+			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0)  /* MCU_OSPI0_D5 */
+			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0)  /* MCU_OSPI0_D6 */
+			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0)  /* MCU_OSPI0_D7 */
+			J721E_WKUP_IOPAD(0x0008, PIN_INPUT, 0)  /* MCU_OSPI0_DQS */
+		>;
+	};
 };
 
 &main_pmx0 {
@@ -235,3 +251,23 @@ exp_som: gpio@21 {
 				  "GPIO_LIN_EN", "CAN_STB";
 	};
 };
+
+&ospi0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_fss0_ospi0_pins_default>;
+
+	flash@0{
+		compatible = "jedec,spi-nor";
+		reg = <0x0>;
+		spi-tx-bus-width = <8>;
+		spi-rx-bus-width = <8>;
+		spi-max-frequency = <25000000>;
+		cdns,tshsl-ns = <60>;
+		cdns,tsd2d-ns = <60>;
+		cdns,tchsh-ns = <60>;
+		cdns,tslch-ns = <60>;
+		cdns,read-delay = <4>;
+		#address-cells = <1>;
+		#size-cells = <1>;
+	};
+};
-- 
2.30.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
