From: Claudiu Beznea <claudiu.beznea@microchip.com>
To: <eugen.hristev@microchip.com>, <jic23@kernel.org>,
<lars@metafoo.de>, <nicolas.ferre@microchip.com>,
<alexandre.belloni@bootlin.com>,
<ludovic.desroches@microchip.com>, <robh+dt@kernel.org>
Cc: <linux-iio@vger.kernel.org>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
Claudiu Beznea <claudiu.beznea@microchip.com>
Subject: [PATCH v3 07/19] iio: adc: at91-sama5d2_adc: move the check of oversampling in its function
Date: Wed, 3 Aug 2022 13:28:43 +0300 [thread overview]
Message-ID: <20220803102855.2191070-8-claudiu.beznea@microchip.com> (raw)
In-Reply-To: <20220803102855.2191070-1-claudiu.beznea@microchip.com>
Oversampling values are checked anyway in at91_adc_emr_config(). Remove
the checking of these from at91_adc_write_raw() and return -EINVAL
instead in at91_adc_emr_config().
Suggested-by: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Claudiu Beznea <claudiu.beznea@microchip.com>
---
drivers/iio/adc/at91-sama5d2_adc.c | 18 ++++++++++--------
1 file changed, 10 insertions(+), 8 deletions(-)
diff --git a/drivers/iio/adc/at91-sama5d2_adc.c b/drivers/iio/adc/at91-sama5d2_adc.c
index 0283c8cc3168..ace4cc431a95 100644
--- a/drivers/iio/adc/at91-sama5d2_adc.c
+++ b/drivers/iio/adc/at91-sama5d2_adc.c
@@ -728,8 +728,8 @@ static void at91_adc_eoc_ena(struct at91_adc_state *st, unsigned int channel)
at91_adc_writel(st, EOC_IER, BIT(channel));
}
-static void at91_adc_config_emr(struct at91_adc_state *st,
- u32 oversampling_ratio)
+static int at91_adc_config_emr(struct at91_adc_state *st,
+ u32 oversampling_ratio)
{
/* configure the extended mode register */
unsigned int emr = at91_adc_readl(st, EMR);
@@ -755,9 +755,13 @@ static void at91_adc_config_emr(struct at91_adc_state *st,
emr |= AT91_SAMA5D2_EMR_OSR(AT91_SAMA5D2_EMR_OSR_16SAMPLES,
osr_mask);
break;
+ default:
+ return -EINVAL;
}
at91_adc_writel(st, EMR, emr);
+
+ return 0;
}
static int at91_adc_adjust_val_osr(struct at91_adc_state *st, int *val)
@@ -1650,9 +1654,6 @@ static int at91_adc_write_raw(struct iio_dev *indio_dev,
switch (mask) {
case IIO_CHAN_INFO_OVERSAMPLING_RATIO:
- if ((val != AT91_OSR_1SAMPLES) && (val != AT91_OSR_4SAMPLES) &&
- (val != AT91_OSR_16SAMPLES))
- return -EINVAL;
/* if no change, optimize out */
if (val == st->oversampling_ratio)
return 0;
@@ -1661,12 +1662,13 @@ static int at91_adc_write_raw(struct iio_dev *indio_dev,
if (ret)
return ret;
mutex_lock(&st->lock);
- st->oversampling_ratio = val;
/* update ratio */
- at91_adc_config_emr(st, val);
+ ret = at91_adc_config_emr(st, val);
+ if (!ret)
+ st->oversampling_ratio = val;
mutex_unlock(&st->lock);
iio_device_release_direct_mode(indio_dev);
- return 0;
+ return ret;
case IIO_CHAN_INFO_SAMP_FREQ:
if (val < st->soc_info.min_sample_rate ||
val > st->soc_info.max_sample_rate)
--
2.34.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2022-08-03 10:30 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2022-08-03 10:28 [PATCH v3 00/19] iio: adc: at91-sama5d2_adc: add support for temperature sensor Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 01/19] iio: adc: at91-sama5d2_adc: fix AT91_SAMA5D2_MR_TRACKTIM_MAX Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 02/19] iio: adc: at91-sama5d2_adc: check return status for pressure and touch Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 03/19] iio: adc: at91-sama5d2_adc: lock around oversampling and sample freq Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 04/19] iio: adc: at91-sama5d2_adc: disable/prepare buffer on suspend/resume Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 05/19] iio: adc: at91-sama5d2_adc: exit from write_raw() when buffers are enabled Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 06/19] iio: adc: at91-sama5d2_adc: handle different EMR.OSR for different hw versions Claudiu Beznea
2022-08-03 10:28 ` Claudiu Beznea [this message]
2022-08-03 10:28 ` [PATCH v3 08/19] iio: adc: at91-sama5d2_adc: drop AT91_OSR_XSAMPLES defines Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 09/19] iio: adc: at91-sama5d2_adc: add .read_avail() chan_info ops Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 10/19] iio: adc: at91-sama5d2_adc: adjust osr based on specific platform data Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 11/19] iio: adc: at91-sama5d2_adc: add 64 and 256 oversampling ratio Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 12/19] iio: adc: at91-sama5d2_adc: move oversampling storage in its function Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 13/19] iio: adc: at91-sama5d2_adc: update trackx on emr Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 14/19] iio: adc: at91-sama5d2_adc: add startup and tracktim as parameter for at91_adc_setup_samp_freq() Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 15/19] iio: adc: at91-sama5d2_adc: lock around at91_adc_read_info_raw() Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 16/19] dt-bindings: iio: adc: at91-sama5d2_adc: add id for temperature channel Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 17/19] iio: adc: at91-sama5d2_adc: add support for temperature sensor Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 18/19] iio: adc: at91-sama5d2_adc: add empty line after functions Claudiu Beznea
2022-08-03 10:28 ` [PATCH v3 19/19] iio: adc: at91-sama5d2_adc: add runtime pm support Claudiu Beznea
2022-08-06 14:10 ` [PATCH v3 00/19] iio: adc: at91-sama5d2_adc: add support for temperature sensor Jonathan Cameron
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20220803102855.2191070-8-claudiu.beznea@microchip.com \
--to=claudiu.beznea@microchip.com \
--cc=alexandre.belloni@bootlin.com \
--cc=devicetree@vger.kernel.org \
--cc=eugen.hristev@microchip.com \
--cc=jic23@kernel.org \
--cc=lars@metafoo.de \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-iio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=ludovic.desroches@microchip.com \
--cc=nicolas.ferre@microchip.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox