[PATCH 0/7] arm64: dts: ti: k3-am65: Cleanups and minor additions

[PATCH 0/7] arm64: dts: ti: k3-am65: Cleanups and minor additions

[Nishanth Menon]

Hi,

This is a result of looking to cleanup u-boot and realizing there are
pieces missing in kernel that need to be pushed out.

So, minor cleanups and adding a few missing pieces.

Bootlog: https://gist.github.com/nmenon/f4dc43aef616dfcb3d38701cc074ff6d

Nishanth Menon (7):
  arm64: dts: ti: k3-am654-base-board: Add missing pinmux wkup_uart,
    mcu_uart and mcu_i2c
  arm64: dts: ti: k3-am654-base-board: Rename regulator node name
  arm64: dts: ti: k3-am654-base-board: Add VTT GPIO regulator for DDR
  arm64: dts: ti: k3-am654-base-board: Add missing PMIC
  arm64: dts: ti: k3-am654-base-board: Add board detect eeprom
  arm64: dts: ti: k3-am654-base-board: Add aliases
  arm64: dts: ti: k3-am65: Drop aliases

 arch/arm64/boot/dts/ti/k3-am65.dtsi           | 17 ----
 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 93 ++++++++++++++++++-
 2 files changed, 88 insertions(+), 22 deletions(-)

-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/7] arm64: dts: ti: k3-am654-base-board: Add missing pinmux wkup_uart, mcu_uart and mcu_i2c

[Nishanth Menon]

Many of the definitions depend on pinmux done by the bootloader. Be
explicit about the pinmux for functionality and completeness.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 34 +++++++++++++++++--
 1 file changed, 32 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 592ab2b54cb3..7a79ef51bcc8 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -120,6 +120,15 @@ vdd_mmc1_sd: fixedregulator-sd {
 };
 
 &wkup_pmx0 {
+	wkup_uart0_pins_default: wkup-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM65X_WKUP_IOPAD(0x00a0, PIN_INPUT, 0)	/* (AB1) WKUP_UART0_RXD */
+			AM65X_WKUP_IOPAD(0x00a4, PIN_OUTPUT, 0)	/* (AB5) WKUP_UART0_TXD */
+			AM65X_WKUP_IOPAD(0x00c8, PIN_INPUT, 1)	/* (AC2) WKUP_GPIO0_6.WKUP_UART0_CTSn */
+			AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 1)	/* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */
+		>;
+	};
+
 	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) /* (AC7) WKUP_I2C0_SCL */
@@ -156,6 +165,15 @@ AM65X_WKUP_IOPAD(0x0034, PIN_INPUT, 7) /* (T1) MCU_OSPI1_CLK.WKUP_GPIO0_25 */
 		>;
 	};
 
+	mcu_uart0_pins_default: mcu-uart0-pins-default {
+		pinctrl-single,pins = <
+			AM65X_WKUP_IOPAD(0x0044, PIN_INPUT, 4)	/* (P4) MCU_OSPI1_D1.MCU_UART0_RXD */
+			AM65X_WKUP_IOPAD(0x0048, PIN_OUTPUT, 4)	/* (P5) MCU_OSPI1_D2.MCU_UART0_TXD */
+			AM65X_WKUP_IOPAD(0x004C, PIN_INPUT, 4)	/* (P1) MCU_OSPI1_D3.MCU_UART0_CTSn */
+			AM65X_WKUP_IOPAD(0x0054, PIN_OUTPUT, 4)	/* (N3) MCU_OSPI1_CSn1.MCU_UART0_RTSn */
+		>;
+	};
+
 	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x0058, PIN_OUTPUT, 0) /* (N4) MCU_RGMII1_TX_CTL */
@@ -179,6 +197,13 @@ AM65X_WKUP_IOPAD(0x008c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
 			AM65X_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
 		>;
 	};
+
+	mcu_i2c0_pins_default: mcu-i2c0-pins-default {
+		pinctrl-single,pins = <
+			AM65X_WKUP_IOPAD(0x00e8, PIN_INPUT,  0) /* (AD8) MCU_I2C0_SCL */
+			AM65X_WKUP_IOPAD(0x00ec, PIN_INPUT,  0) /* (AD7) MCU_I2C0_SDA */
+		>;
+	};
 };
 
 &main_pmx0 {
@@ -269,11 +294,14 @@ AM65X_IOPAD(0x0010, PIN_INPUT, 0) /* (D21) ECAP0_IN_APWM_OUT */
 &wkup_uart0 {
 	/* Wakeup UART is used by System firmware */
 	status = "reserved";
+	pinctrl-names = "default";
+	pinctrl-0 = <&wkup_uart0_pins_default>;
 };
 
 &mcu_uart0 {
 	status = "okay";
-	/* Default pinmux */
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_uart0_pins_default>;
 };
 
 &main_uart0 {
@@ -305,7 +333,9 @@ pca9554: gpio@39 {
 
 &mcu_i2c0 {
 	status = "okay";
-	/* Default pinmux */
+	pinctrl-names = "default";
+	pinctrl-0 = <&mcu_i2c0_pins_default>;
+	clock-frequency = <400000>;
 };
 
 &main_i2c0 {
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 2/7] arm64: dts: ti: k3-am654-base-board: Rename regulator node name

[Nishanth Menon]

Rename the regulator node names to the standard regulator-0.. numbers.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 7a79ef51bcc8..d3dd6899ef03 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -86,7 +86,7 @@ switch-6 {
 		};
 	};
 
-	evm_12v0: fixedregulator-evm12v0 {
+	evm_12v0: regulator-0 {
 		/* main supply */
 		compatible = "regulator-fixed";
 		regulator-name = "evm_12v0";
@@ -96,7 +96,7 @@ evm_12v0: fixedregulator-evm12v0 {
 		regulator-boot-on;
 	};
 
-	vcc3v3_io: fixedregulator-vcc3v3io {
+	vcc3v3_io: regulator-1 {
 		/* Output of TPS54334 */
 		compatible = "regulator-fixed";
 		regulator-name = "vcc3v3_io";
@@ -107,7 +107,7 @@ vcc3v3_io: fixedregulator-vcc3v3io {
 		vin-supply = <&evm_12v0>;
 	};
 
-	vdd_mmc1_sd: fixedregulator-sd {
+	vdd_mmc1_sd: regulator-2 {
 		compatible = "regulator-fixed";
 		regulator-name = "vdd_mmc1_sd";
 		regulator-min-microvolt = <3300000>;
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 3/7] arm64: dts: ti: k3-am654-base-board: Add VTT GPIO regulator for DDR

[Nishanth Menon]

Hold the DDR vtt regulator active for functionality.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 .../arm64/boot/dts/ti/k3-am654-base-board.dts | 20 +++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index d3dd6899ef03..83467adc017d 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -117,6 +117,20 @@ vdd_mmc1_sd: regulator-2 {
 		vin-supply = <&vcc3v3_io>;
 		gpio = <&pca9554 4 GPIO_ACTIVE_HIGH>;
 	};
+
+	vtt_supply: regulator-3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vtt";
+		pinctrl-names = "default";
+		pinctrl-0 = <&ddr_vtt_pins_default>;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		enable-active-high;
+		regulator-always-on;
+		regulator-boot-on;
+		vin-supply = <&vcc3v3_io>;
+		gpio = <&wkup_gpio0 28 GPIO_ACTIVE_HIGH>;
+	};
 };
 
 &wkup_pmx0 {
@@ -129,6 +143,12 @@ AM65X_WKUP_IOPAD(0x00cc, PIN_OUTPUT, 1)	/* (AC1) WKUP_GPIO0_7.WKUP_UART0_RTSn */
 		>;
 	};
 
+	ddr_vtt_pins_default: ddr-vtt-pins-default {
+		pinctrl-single,pins = <
+			AM65X_WKUP_IOPAD(0x0040, PIN_OUTPUT_PULLUP, 7)	/* WKUP_GPIO0_28 */
+		>;
+	};
+
 	wkup_i2c0_pins_default: wkup-i2c0-pins-default {
 		pinctrl-single,pins = <
 			AM65X_WKUP_IOPAD(0x00e0, PIN_INPUT, 0) /* (AC7) WKUP_I2C0_SCL */
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 4/7] arm64: dts: ti: k3-am654-base-board: Add missing PMIC

[Nishanth Menon]

Add the missing vdd_mpu PMIC.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 13 +++++++++++++
 1 file changed, 13 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 83467adc017d..640910e2280f 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -337,6 +337,19 @@ &wkup_i2c0 {
 	pinctrl-0 = <&wkup_i2c0_pins_default>;
 	clock-frequency = <400000>;
 
+	vdd_mpu: regulator@60 {
+		compatible = "ti,tps62363";
+		reg = <0x60>;
+		regulator-name = "VDD_MPU";
+		regulator-min-microvolt = <500000>;
+		regulator-max-microvolt = <1770000>;
+		regulator-always-on;
+		regulator-boot-on;
+		ti,vsel0-state-high;
+		ti,vsel1-state-high;
+		ti,enable-vout-discharge;
+	};
+
 	pca9554: gpio@39 {
 		compatible = "nxp,pca9554";
 		reg = <0x39>;
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 5/7] arm64: dts: ti: k3-am654-base-board: Add board detect eeprom

[Nishanth Menon]

Enable AT24CM01 on the base board using the corresponding compatible.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index 640910e2280f..c10266077f53 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -337,6 +337,12 @@ &wkup_i2c0 {
 	pinctrl-0 = <&wkup_i2c0_pins_default>;
 	clock-frequency = <400000>;
 
+	eeprom@50 {
+		/* AT24CM01 */
+		compatible = "atmel,24c1024";
+		reg = <0x50>;
+	};
+
 	vdd_mpu: regulator@60 {
 		compatible = "ti,tps62363";
 		reg = <0x60>;
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 6/7] arm64: dts: ti: k3-am654-base-board: Add aliases

[Nishanth Menon]

Introduce aliases compatible with the base definition, but focussed on
the interfaces that have been exposed on the platform.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am654-base-board.dts | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
index c10266077f53..628c72dcec79 100644
--- a/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
+++ b/arch/arm64/boot/dts/ti/k3-am654-base-board.dts
@@ -13,6 +13,20 @@ / {
 	compatible = "ti,am654-evm", "ti,am654";
 	model = "Texas Instruments AM654 Base Board";
 
+	aliases {
+		serial0 = &wkup_uart0;
+		serial1 = &mcu_uart0;
+		serial2 = &main_uart0;
+		i2c0 = &wkup_i2c0;
+		i2c1 = &mcu_i2c0;
+		i2c2 = &main_i2c0;
+		i2c3 = &main_i2c1;
+		i2c4 = &main_i2c2;
+		ethernet0 = &cpsw_port1;
+		mmc0 = &sdhci0;
+		mmc1 = &sdhci1;
+	};
+
 	chosen {
 		stdout-path = "serial2:115200n8";
 		bootargs = "earlycon=ns16550a,mmio32,0x02800000";
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 7/7] arm64: dts: ti: k3-am65: Drop aliases

[Nishanth Menon]

iot boards have always defined their own aliases and with the base-board
defining it's own aliases, there are no pending boards depending on
common aliases defined in SoC level.

aliases are meant to be defined appropriately based on the exposed
interfaces at a board level, drop the aliases defined at SoC level.

Signed-off-by: Nishanth Menon <nm@ti.com>
---
 arch/arm64/boot/dts/ti/k3-am65.dtsi | 17 -----------------
 1 file changed, 17 deletions(-)

diff --git a/arch/arm64/boot/dts/ti/k3-am65.dtsi b/arch/arm64/boot/dts/ti/k3-am65.dtsi
index 3093ef6b9b23..4d7b6155a76b 100644
--- a/arch/arm64/boot/dts/ti/k3-am65.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-am65.dtsi
@@ -19,23 +19,6 @@ / {
 	#address-cells = <2>;
 	#size-cells = <2>;
 
-	aliases {
-		serial0 = &wkup_uart0;
-		serial1 = &mcu_uart0;
-		serial2 = &main_uart0;
-		serial3 = &main_uart1;
-		serial4 = &main_uart2;
-		i2c0 = &wkup_i2c0;
-		i2c1 = &mcu_i2c0;
-		i2c2 = &main_i2c0;
-		i2c3 = &main_i2c1;
-		i2c4 = &main_i2c2;
-		i2c5 = &main_i2c3;
-		ethernet0 = &cpsw_port1;
-		mmc0 = &sdhci0;
-		mmc1 = &sdhci1;
-	};
-
 	chosen { };
 
 	firmware {
-- 
2.40.0


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/7] arm64: dts: ti: k3-am65: Cleanups and minor additions

[Kamlesh Gurudasani]

Nishanth Menon <nm@ti.com> writes:

> Hi,
>
> This is a result of looking to cleanup u-boot and realizing there are
> pieces missing in kernel that need to be pushed out.
>
> So, minor cleanups and adding a few missing pieces.
>
> Bootlog: https://gist.github.com/nmenon/f4dc43aef616dfcb3d38701cc074ff6d
>
> Nishanth Menon (7):
>   arm64: dts: ti: k3-am654-base-board: Add missing pinmux wkup_uart,
>     mcu_uart and mcu_i2c
>   arm64: dts: ti: k3-am654-base-board: Rename regulator node name
>   arm64: dts: ti: k3-am654-base-board: Add VTT GPIO regulator for DDR
>   arm64: dts: ti: k3-am654-base-board: Add missing PMIC
>   arm64: dts: ti: k3-am654-base-board: Add board detect eeprom
>   arm64: dts: ti: k3-am654-base-board: Add aliases
>   arm64: dts: ti: k3-am65: Drop aliases
>
>  arch/arm64/boot/dts/ti/k3-am65.dtsi           | 17 ----
>  .../arm64/boot/dts/ti/k3-am654-base-board.dts | 93 ++++++++++++++++++-
>  2 files changed, 88 insertions(+), 22 deletions(-)
>
> -- 
> 2.40.0
All patches look good to me.

Reviewed-by: Kamlesh Gurudasani <kamlesh@ti.com>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH 0/7] arm64: dts: ti: k3-am65: Cleanups and minor additions

[Vignesh Raghavendra]

Hi Nishanth Menon,

On Wed, 19 Apr 2023 17:59:06 -0500, Nishanth Menon wrote:
> This is a result of looking to cleanup u-boot and realizing there are
> pieces missing in kernel that need to be pushed out.
> 
> So, minor cleanups and adding a few missing pieces.
> 
> Bootlog: https://gist.github.com/nmenon/f4dc43aef616dfcb3d38701cc074ff6d
> 
> [...]

I have applied the following to branch ti-k3-dts-next on [1].
Thank you!

[1/7] arm64: dts: ti: k3-am654-base-board: Add missing pinmux wkup_uart, mcu_uart and mcu_i2c
      commit: 3ae28642a110485f71091f0a631492e78b396b2b
[2/7] arm64: dts: ti: k3-am654-base-board: Rename regulator node name
      commit: ec1b54824f022a7e65d858abbe74f5d7effc9817
[3/7] arm64: dts: ti: k3-am654-base-board: Add VTT GPIO regulator for DDR
      commit: 5292f504827c56406975b463eda1270d144cf06f
[4/7] arm64: dts: ti: k3-am654-base-board: Add missing PMIC
      commit: 282621ed6e790ccf7288c4c0aadbb34f1fe25c11
[5/7] arm64: dts: ti: k3-am654-base-board: Add board detect eeprom
      commit: 895e2f4f9852e54c0e6d16ddea9882b9b2065eae
[6/7] arm64: dts: ti: k3-am654-base-board: Add aliases
      commit: 692e8888a84357232574caba74f60ceea7364016
[7/7] arm64: dts: ti: k3-am65: Drop aliases
      commit: ffc449e016e269ce4d19e648bae584f8e5afd59f

All being well this means that it will be integrated into the linux-next
tree (usually sometime in the next 24 hours) and sent up the chain during
the next merge window (or sooner if it is a relevant bug fix), however if
problems are discovered then the patch may be dropped or reverted.

You may get further e-mails resulting from automated or manual testing
and review of the tree, please engage with people reporting problems and
send followup patches addressing any issues that are reported if needed.

If any updates are required or you are submitting further changes they
should be sent as incremental updates against current git, existing
patches will not be replaced.

Please add any relevant lists and maintainers to the CCs when replying
to this mail.

[1] https://git.kernel.org/pub/scm/linux/kernel/git/ti/linux.git
--
Vignesh


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel