From: Andre Przywara <andre.przywara@arm.com>
To: Vasily Khoruzhick <anarsoul@gmail.com>,
Yangtao Li <tiny.windzz@gmail.com>, Chen-Yu Tsai <wens@csie.org>,
Jernej Skrabec <jernej.skrabec@gmail.com>,
Samuel Holland <samuel@sholland.org>
Cc: "Rafael J . Wysocki" <rafael@kernel.org>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Zhang Rui <rui.zhang@intel.com>,
Lukasz Luba <lukasz.luba@arm.com>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
Martin Botka <martin.botka@somainline.org>,
Maksim Kiselev <bigunclemax@gmail.com>,
Bob McChesney <bob@electricworry.net>,
linux-pm@vger.kernel.org, devicetree@vger.kernel.org,
linux-arm-kernel@lists.infradead.org,
linux-sunxi@lists.linux.dev
Subject: [PATCH v4 6/7] thermal: sun8i: add support for H616 THS controller
Date: Fri, 9 Feb 2024 14:42:20 +0000 [thread overview]
Message-ID: <20240209144221.3602382-7-andre.przywara@arm.com> (raw)
In-Reply-To: <20240209144221.3602382-1-andre.przywara@arm.com>
From: Martin Botka <martin.botka@somainline.org>
Add support for the thermal sensor found in H616 SoCs, is the same as
the H6 thermal sensor controller, but with four sensors.
Also the registers readings are wrong, unless a bit in the first SYS_CFG
register cleared, so set exercise the SRAM regmap to take care of that.
Signed-off-by: Martin Botka <martin.botka@somainline.org>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
---
drivers/thermal/sun8i_thermal.c | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/drivers/thermal/sun8i_thermal.c b/drivers/thermal/sun8i_thermal.c
index 8a9d2bdc71ece..172410a9e0274 100644
--- a/drivers/thermal/sun8i_thermal.c
+++ b/drivers/thermal/sun8i_thermal.c
@@ -683,6 +683,20 @@ static const struct ths_thermal_chip sun20i_d1_ths = {
.calc_temp = sun8i_ths_calc_temp,
};
+static const struct ths_thermal_chip sun50i_h616_ths = {
+ .sensor_num = 4,
+ .has_bus_clk_reset = true,
+ .needs_sram = true,
+ .ft_deviation = 8000,
+ .offset = 263655,
+ .scale = 810,
+ .temp_data_base = SUN50I_H6_THS_TEMP_DATA,
+ .calibrate = sun50i_h6_ths_calibrate,
+ .init = sun50i_h6_thermal_init,
+ .irq_ack = sun50i_h6_irq_ack,
+ .calc_temp = sun8i_ths_calc_temp,
+};
+
static const struct of_device_id of_ths_match[] = {
{ .compatible = "allwinner,sun8i-a83t-ths", .data = &sun8i_a83t_ths },
{ .compatible = "allwinner,sun8i-h3-ths", .data = &sun8i_h3_ths },
@@ -692,6 +706,7 @@ static const struct of_device_id of_ths_match[] = {
{ .compatible = "allwinner,sun50i-h5-ths", .data = &sun50i_h5_ths },
{ .compatible = "allwinner,sun50i-h6-ths", .data = &sun50i_h6_ths },
{ .compatible = "allwinner,sun20i-d1-ths", .data = &sun20i_d1_ths },
+ { .compatible = "allwinner,sun50i-h616-ths", .data = &sun50i_h616_ths },
{ /* sentinel */ },
};
MODULE_DEVICE_TABLE(of, of_ths_match);
--
2.25.1
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2024-02-09 14:43 UTC|newest]
Thread overview: 15+ messages / expand[flat|nested] mbox.gz Atom feed top
2024-02-09 14:42 [PATCH v4 0/7] add support for H616 thermal system Andre Przywara
2024-02-09 14:42 ` [PATCH v4 1/7] soc: sunxi: sram: export register 0 for THS on H616 Andre Przywara
2024-02-14 20:29 ` Jernej Škrabec
2024-02-15 1:28 ` Andre Przywara
2024-02-15 21:18 ` Jernej Škrabec
2024-02-09 14:42 ` [PATCH v4 2/7] dt-bindings: thermal: sun8i: Add H616 THS controller Andre Przywara
2024-02-11 16:31 ` Krzysztof Kozlowski
2024-02-09 14:42 ` [PATCH v4 3/7] thermal: sun8i: explain unknown H6 register value Andre Przywara
2024-02-14 20:31 ` Jernej Škrabec
2024-02-09 14:42 ` [PATCH v4 4/7] thermal: sun8i: extend H6 calibration to support 4 sensors Andre Przywara
2024-02-14 20:35 ` Jernej Škrabec
2024-02-09 14:42 ` [PATCH v4 5/7] thermal: sun8i: add SRAM register access code Andre Przywara
2024-02-15 21:24 ` Jernej Škrabec
2024-02-09 14:42 ` Andre Przywara [this message]
2024-02-09 14:42 ` [PATCH v4 7/7] arm64: dts: allwinner: h616: Add thermal sensor and zones Andre Przywara
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20240209144221.3602382-7-andre.przywara@arm.com \
--to=andre.przywara@arm.com \
--cc=anarsoul@gmail.com \
--cc=bigunclemax@gmail.com \
--cc=bob@electricworry.net \
--cc=conor+dt@kernel.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=jernej.skrabec@gmail.com \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-sunxi@lists.linux.dev \
--cc=lukasz.luba@arm.com \
--cc=martin.botka@somainline.org \
--cc=rafael@kernel.org \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=samuel@sholland.org \
--cc=tiny.windzz@gmail.com \
--cc=wens@csie.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox