[PATCH v5 0/5] Add CPSW2G and CPSW9G nodes for J784S4

[PATCH v5 0/5] Add CPSW2G and CPSW9G nodes for J784S4

[Chintan Vankar]

This series adds device-tree nodes for CPSW2G and CPSW9G instance
of the CPSW Ethernet Switch on TI's J784S4 SoC. Additionally,
two device-tree overlays are also added:
1. QSGMII mode with the CPSW9G instance via the ENET EXPANSION 1
   connector.
2. USXGMII mode with MAC Ports 1 and 2 of the CPSW9G instance via
   ENET EXPANSION 1 and 2 connectors, configured in fixed-link
   mode of operation at 5Gbps link speed.

Link to v4:
https://lore.kernel.org/r/20240131101441.1362409-1-c-vankar@ti.com/

Changes from v4 to v5:
1. Removed Patch at:
   https://lore.kernel.org/r/20240131101441.1362409-2-c-vankar@ti.com/
   from this version as it is posted as a separate patch at:
   https://lore.kernel.org/r/20240213080348.248916-1-s-vadapalli@ti.com/
2. Disabled node "main_cpsw1_mdio" in k3-j784s4-main.dtsi and enabled it
   in k3-j784s4-evm.dts.

Chintan Vankar (1):
  arm64: dts: ti: k3-j784s4-evm: Add alias for MCU CPSW2G

Siddharth Vadapalli (4):
  arm64: dts: ti: k3-j784s4-main: Add CPSW2G and CPSW9G nodes
  arm64: dts: ti: k3-j784s4-evm: Enable Main CPSW2G node and add aliases
    for it
  arm64: dts: ti: k3-j784s4: Add overlay to enable QSGMII mode with
    CPSW9G
  arm64: dts: ti: k3-j784s4: Add overlay for dual port USXGMII mode

 arch/arm64/boot/dts/ti/Makefile               |  11 +-
 .../ti/k3-j784s4-evm-quad-port-eth-exp1.dtso  | 147 ++++++++++++++
 .../ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso   |  81 ++++++++
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts      |  51 +++++
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi    | 187 ++++++++++++++++++
 5 files changed, 476 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
 create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso

-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 1/5] arm64: dts: ti: k3-j784s4-evm: Add alias for MCU CPSW2G

[Chintan Vankar]

Add alias for the MCU CPSW2G port to enable Linux to fetch MAC Address
for the port directly from U-Boot.

Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 81fd7afac8c5..1f390c22844e 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -27,6 +27,7 @@ aliases {
 		mmc1 = &main_sdhci1;
 		i2c0 = &wkup_i2c0;
 		i2c3 = &main_i2c0;
+		ethernet0 = &mcu_cpsw_port1;
 	};
 
 	memory@80000000 {
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 2/5] arm64: dts: ti: k3-j784s4-main: Add CPSW2G and CPSW9G nodes

[Chintan Vankar]

From: Siddharth Vadapalli <s-vadapalli@ti.com>

J784S4 SoC has MAIN CPSW2G and CPSW9G instances of the CPSW
Ethernet Switch. CPSW2G has 1 external port and 1 host port
while CPSW9G has 8 external ports and 1 host port.

Add device-tree nodes for MAIN CPSW2G and CPSW9G and disable
them by default. MAIN CPSW2G will be enabled in the board file
while device-tree overlays will be used to enable CPSW9G.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 187 +++++++++++++++++++++
 1 file changed, 187 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
index b67c37460a73..ddf28b2143aa 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
@@ -48,6 +48,19 @@ scm_conf: bus@100000 {
 		#size-cells = <1>;
 		ranges = <0x00 0x00 0x00100000 0x1c000>;
 
+		cpsw1_phy_gmii_sel: phy@4034 {
+			compatible = "ti,am654-phy-gmii-sel";
+			reg = <0x4034 0x4>;
+			#phy-cells = <1>;
+		};
+
+		cpsw0_phy_gmii_sel: phy@4044 {
+			compatible = "ti,j784s4-cpsw9g-phy-gmii-sel";
+			ti,qsgmii-main-ports = <7>, <7>;
+			reg = <0x4044 0x20>;
+			#phy-cells = <1>;
+		};
+
 		serdes_ln_ctrl: mux-controller@4080 {
 			compatible = "reg-mux";
 			reg = <0x00004080 0x30>;
@@ -1439,6 +1452,180 @@ cpts@310d0000 {
 		};
 	};
 
+	main_cpsw0: ethernet@c000000 {
+		compatible = "ti,j784s4-cpswxg-nuss";
+		reg = <0x00 0xc000000 0x00 0x200000>;
+		reg-names = "cpsw_nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		ranges = <0x00 0x00 0x00 0xc000000 0x00 0x200000>;
+		dma-coherent;
+		clocks = <&k3_clks 64 0>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 64 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&main_udmap 0xca00>,
+		       <&main_udmap 0xca01>,
+		       <&main_udmap 0xca02>,
+		       <&main_udmap 0xca03>,
+		       <&main_udmap 0xca04>,
+		       <&main_udmap 0xca05>,
+		       <&main_udmap 0xca06>,
+		       <&main_udmap 0xca07>,
+		       <&main_udmap 0x4a00>;
+		dma-names = "tx0", "tx1", "tx2", "tx3",
+			    "tx4", "tx5", "tx6", "tx7",
+			    "rx";
+
+		status = "disabled";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			main_cpsw0_port1: port@1 {
+				reg = <1>;
+				label = "port1";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port2: port@2 {
+				reg = <2>;
+				label = "port2";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port3: port@3 {
+				reg = <3>;
+				label = "port3";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port4: port@4 {
+				reg = <4>;
+				label = "port4";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port5: port@5 {
+				reg = <5>;
+				label = "port5";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port6: port@6 {
+				reg = <6>;
+				label = "port6";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port7: port@7 {
+				reg = <7>;
+				label = "port7";
+				ti,mac-only;
+				status = "disabled";
+			};
+
+			main_cpsw0_port8: port@8 {
+				reg = <8>;
+				label = "port8";
+				ti,mac-only;
+				status = "disabled";
+			};
+		};
+
+		main_cpsw0_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio","ti,davinci_mdio";
+			reg = <0x00 0xf00 0x00 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 64 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+			status = "disabled";
+		};
+
+		cpts@3d000 {
+			compatible = "ti,am65-cpts";
+			reg = <0x00 0x3d000 0x00 0x400>;
+			clocks = <&k3_clks 64 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+
+	main_cpsw1: ethernet@c200000 {
+		compatible = "ti,j721e-cpsw-nuss";
+		#address-cells = <2>;
+		#size-cells = <2>;
+		reg = <0x00 0xc200000 0x00 0x200000>;
+		reg-names = "cpsw_nuss";
+		ranges = <0x00 0x00 0x00 0xc200000 0x00 0x200000>;
+		dma-coherent;
+		clocks = <&k3_clks 62 0>;
+		clock-names = "fck";
+		power-domains = <&k3_pds 62 TI_SCI_PD_EXCLUSIVE>;
+
+		dmas = <&main_udmap 0xc640>,
+			<&main_udmap 0xc641>,
+			<&main_udmap 0xc642>,
+			<&main_udmap 0xc643>,
+			<&main_udmap 0xc644>,
+			<&main_udmap 0xc645>,
+			<&main_udmap 0xc646>,
+			<&main_udmap 0xc647>,
+			<&main_udmap 0x4640>;
+		dma-names = "tx0", "tx1", "tx2", "tx3",
+				"tx4", "tx5", "tx6", "tx7",
+				"rx";
+
+		status = "disabled";
+
+		ethernet-ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			main_cpsw1_port1: port@1 {
+				reg = <1>;
+				label = "port1";
+				phys = <&cpsw1_phy_gmii_sel 1>;
+				ti,mac-only;
+				status = "disabled";
+			};
+		};
+
+		main_cpsw1_mdio: mdio@f00 {
+			compatible = "ti,cpsw-mdio", "ti,davinci_mdio";
+			reg = <0x00 0xf00 0x00 0x100>;
+			#address-cells = <1>;
+			#size-cells = <0>;
+			clocks = <&k3_clks 62 0>;
+			clock-names = "fck";
+			bus_freq = <1000000>;
+			status = "disabled";
+		};
+
+		cpts@3d000 {
+			compatible = "ti,am65-cpts";
+			reg = <0x00 0x3d000 0x00 0x400>;
+			clocks = <&k3_clks 62 3>;
+			clock-names = "cpts";
+			interrupts-extended = <&gic500 GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+			interrupt-names = "cpts";
+			ti,cpts-ext-ts-inputs = <4>;
+			ti,cpts-periodic-outputs = <2>;
+		};
+	};
+
 	main_mcan0: can@2701000 {
 		compatible = "bosch,m_can";
 		reg = <0x00 0x02701000 0x00 0x200>,
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 3/5] arm64: dts: ti: k3-j784s4-evm: Enable Main CPSW2G node and add aliases for it

[Chintan Vankar]

From: Siddharth Vadapalli <s-vadapalli@ti.com>

Enable MAIN CPSW2G and add alias for it to enable Linux to fetch
MAC Address for the port directly from U-Boot.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
 arch/arm64/boot/dts/ti/k3-j784s4-evm.dts | 50 ++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
index 1f390c22844e..49195349a156 100644
--- a/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm.dts
@@ -28,6 +28,7 @@ aliases {
 		i2c0 = &wkup_i2c0;
 		i2c3 = &main_i2c0;
 		ethernet0 = &mcu_cpsw_port1;
+		ethernet1 = &main_cpsw1_port1;
 	};
 
 	memory@80000000 {
@@ -281,6 +282,30 @@ &wkup_gpio0 {
 
 &main_pmx0 {
 	bootph-all;
+	main_cpsw2g_default_pins: main-cpsw2g-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0b8, PIN_INPUT, 6) /* (AC34) MCASP1_ACLKX.RGMII1_RD0 */
+			J784S4_IOPAD(0x0a0, PIN_INPUT, 6) /* (AD34) MCASP0_AXR12.RGMII1_RD1 */
+			J784S4_IOPAD(0x0a4, PIN_INPUT, 6) /* (AJ36) MCASP0_AXR13.RGMII1_RD2 */
+			J784S4_IOPAD(0x0a8, PIN_INPUT, 6) /* (AF34) MCASP0_AXR14.RGMII1_RD3 */
+			J784S4_IOPAD(0x0b0, PIN_INPUT, 6) /* (AL33) MCASP1_AXR3.RGMII1_RXC */
+			J784S4_IOPAD(0x0ac, PIN_INPUT, 6) /* (AE34) MCASP0_AXR15.RGMII1_RX_CTL */
+			J784S4_IOPAD(0x08c, PIN_INPUT, 6) /* (AE35) MCASP0_AXR7.RGMII1_TD0 */
+			J784S4_IOPAD(0x090, PIN_INPUT, 6) /* (AC35) MCASP0_AXR8.RGMII1_TD1 */
+			J784S4_IOPAD(0x094, PIN_INPUT, 6) /* (AG35) MCASP0_AXR9.RGMII1_TD2 */
+			J784S4_IOPAD(0x098, PIN_INPUT, 6) /* (AH36) MCASP0_AXR10.RGMII1_TD3 */
+			J784S4_IOPAD(0x0b4, PIN_INPUT, 6) /* (AL34) MCASP1_AXR4.RGMII1_TXC */
+			J784S4_IOPAD(0x09c, PIN_INPUT, 6) /* (AF35) MCASP0_AXR11.RGMII1_TX_CTL */
+		>;
+	};
+
+	main_cpsw2g_mdio_default_pins: main-cpsw2g-mdio-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x0c0, PIN_INPUT, 6) /* (AD38) MCASP1_AXR0.MDIO0_MDC */
+			J784S4_IOPAD(0x0bc, PIN_INPUT, 6) /* (AD33) MCASP1_AFSX.MDIO0_MDIO */
+		>;
+	};
+
 	main_uart8_pins_default: main-uart8-default-pins {
 		bootph-all;
 		pinctrl-single,pins = <
@@ -833,6 +858,31 @@ &mcu_cpsw_port1 {
 	phy-handle = <&mcu_phy0>;
 };
 
+&main_cpsw1 {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_cpsw2g_default_pins>;
+};
+
+&main_cpsw1_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&main_cpsw2g_mdio_default_pins>;
+
+	main_cpsw1_phy0: ethernet-phy@0 {
+		reg = <0>;
+		ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>;
+		ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>;
+		ti,min-output-impedance;
+	};
+};
+
+&main_cpsw1_port1 {
+	status = "okay";
+	phy-mode = "rgmii-rxid";
+	phy-handle = <&main_cpsw1_phy0>;
+};
+
 &mailbox0_cluster0 {
 	status = "okay";
 	interrupts = <436>;
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 4/5] arm64: dts: ti: k3-j784s4: Add overlay to enable QSGMII mode with CPSW9G

[Chintan Vankar]

From: Siddharth Vadapalli <s-vadapalli@ti.com>

The J7 Quad Port Add-On Ethernet Card for J784S4 EVM supports
QSGMII mode. Use the overlay to configure CPSW9G ports in QSGMII
mode with the Add-On Ethernet Card connected to the ENET Expansion
1 slot on the EVM.

Add support to reset the PHY from kernel by using gpio-hog and
gpio-reset.

Add aliases for CPSW9G ports to enable kernel to fetch MAC Addresses
directly from U-Boot.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
 arch/arm64/boot/dts/ti/Makefile               |   7 +-
 .../ti/k3-j784s4-evm-quad-port-eth-exp1.dtso  | 147 ++++++++++++++++++
 2 files changed, 153 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index 9a722c2473fb..f8e47278df43 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -100,6 +100,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
 # Boards with J784s4 SoC
 dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
 
 # Build time test only, enabled by CONFIG_OF_ALL_DTBS
 k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
@@ -145,6 +146,8 @@ k3-j721e-sk-csi2-dual-imx219-dtbs := k3-j721e-sk.dtb \
 	k3-j721e-sk-csi2-dual-imx219.dtbo
 k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
 	k3-j721s2-evm-pcie1-ep.dtbo
+k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
+	k3-j784s4-evm-quad-port-eth-exp1.dtbo
 dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
 	k3-am625-beagleplay-csi2-tevi-ov5640.dtb \
 	k3-am625-sk-csi2-imx219.dtb \
@@ -165,7 +168,8 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
 	k3-am69-sk-csi2-dual-imx219-dtbs \
 	k3-j721e-evm-pcie0-ep.dtb \
 	k3-j721e-sk-csi2-dual-imx219-dtbs \
-	k3-j721s2-evm-pcie1-ep.dtb
+	k3-j721s2-evm-pcie1-ep.dtb \
+	k3-j784s4-evm-quad-port-eth-exp1.dtb
 
 # Enable support for device-tree overlays
 DTC_FLAGS_k3-am625-beagleplay += -@
@@ -181,3 +185,4 @@ DTC_FLAGS_k3-am69-sk += -@
 DTC_FLAGS_k3-j721e-common-proc-board += -@
 DTC_FLAGS_k3-j721e-sk += -@
 DTC_FLAGS_k3-j721s2-common-proc-board += -@
+DTC_FLAGS_k3-j784s4-evm += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso b/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
new file mode 100644
index 000000000000..0667389b07be
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm-quad-port-eth-exp1.dtso
@@ -0,0 +1,147 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/**
+ * DT Overlay for CPSW9G in QSGMII mode using J7 Quad Port ETH EXP Add-On Ethernet Card with
+ * J784S4 EVM. The Add-On Ethernet Card has to be connected to ENET Expansion 1 slot on the
+ * board.
+ *
+ * Product Datasheet: https://www.ti.com/lit/ug/spruj74/spruj74.pdf
+ *
+ * Link to QSGMII Daughtercard: https://www.ti.com/tool/J721EXENETXPANEVM
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-pinctrl.h"
+#include "k3-serdes.h"
+
+&{/} {
+	aliases {
+		ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@5";
+		ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@6";
+		ethernet3 = "/bus@100000/ethernet@c000000/ethernet-ports/port@7";
+		ethernet4 = "/bus@100000/ethernet@c000000/ethernet-ports/port@8";
+		ethernet5 = "/bus@100000/ethernet@c200000/ethernet-ports/port@1";
+	};
+};
+
+&main_cpsw0 {
+	status = "okay";
+};
+
+&main_cpsw0_port5 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy1>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 5>, <&serdes2_qsgmii_link>;
+	phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_port6 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy2>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 6>, <&serdes2_qsgmii_link>;
+	phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_port7 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy0>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 7>, <&serdes2_qsgmii_link>;
+	phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_port8 {
+	status = "okay";
+	phy-handle = <&cpsw9g_phy3>;
+	phy-mode = "qsgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 8>, <&serdes2_qsgmii_link>;
+	phy-names = "mac", "serdes";
+};
+
+&main_cpsw0_mdio {
+	status = "okay";
+	pinctrl-names = "default";
+	pinctrl-0 = <&mdio0_default_pins>;
+	bus_freq = <1000000>;
+	reset-gpios = <&exp2 17 GPIO_ACTIVE_LOW>;
+	reset-post-delay-us = <120000>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	cpsw9g_phy0: ethernet-phy@16 {
+		reg = <16>;
+	};
+	cpsw9g_phy1: ethernet-phy@17 {
+		reg = <17>;
+	};
+	cpsw9g_phy2: ethernet-phy@18 {
+		reg = <18>;
+	};
+	cpsw9g_phy3: ethernet-phy@19 {
+		reg = <19>;
+	};
+};
+
+&exp2 {
+	/* Power-up ENET1 EXPANDER PHY. */
+	qsgmii-line-hog {
+		gpio-hog;
+		gpios = <16 GPIO_ACTIVE_HIGH>;
+		output-low;
+	};
+
+	/* Toggle MUX2 for MDIO lines */
+	mux-sel-hog {
+		gpio-hog;
+		gpios = <13 GPIO_ACTIVE_HIGH>, <14 GPIO_ACTIVE_HIGH>, <15 GPIO_ACTIVE_HIGH>;
+		output-high;
+	};
+};
+
+&main_pmx0 {
+	mdio0_default_pins: mdio0-default-pins {
+		pinctrl-single,pins = <
+			J784S4_IOPAD(0x05c, PIN_INPUT, 4) /* (AC36) MCASP2_AXR0.MDIO1_MDIO */
+			J784S4_IOPAD(0x058, PIN_INPUT, 4) /* (AE37) MCASP2_AFSX.MDIO1_MDC */
+		>;
+	};
+};
+
+&serdes_ln_ctrl {
+	idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+		      <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
+		      <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+		      <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+		      <J784S4_SERDES2_LANE0_QSGMII_LANE5>, <J784S4_SERDES2_LANE1_QSGMII_LANE6>,
+		      <J784S4_SERDES2_LANE2_QSGMII_LANE7>, <J784S4_SERDES2_LANE3_QSGMII_LANE8>;
+};
+
+&serdes_wiz2 {
+	status = "okay";
+};
+
+&serdes2 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+	serdes2_qsgmii_link: phy@0 {
+		reg = <2>;
+		cdns,num-lanes = <1>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_QSGMII>;
+		resets = <&serdes_wiz2 3>;
+	};
+};
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH v5 5/5] arm64: dts: ti: k3-j784s4: Add overlay for dual port USXGMII mode

[Chintan Vankar]

From: Siddharth Vadapalli <s-vadapalli@ti.com>

The CPSW9G instance of the CPSW Ethernet Switch supports USXGMII mode
with MAC Ports 1 and 2 of the instance, which are connected to ENET
Expansion 1 and ENET Expansion 2 slots on the EVM respectively, through
the Serdes2 instance of the SERDES.

Enable CPSW9G MAC Ports 1 and 2 in fixed-link configuration USXGMII mode
at 5 Gbps each.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: Chintan Vankar <c-vankar@ti.com>
---
 arch/arm64/boot/dts/ti/Makefile               |  6 +-
 .../ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso   | 81 +++++++++++++++++++
 2 files changed, 86 insertions(+), 1 deletion(-)
 create mode 100644 arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index f8e47278df43..2d798ef415e4 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -101,6 +101,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-j722s-evm.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-quad-port-eth-exp1.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
 
 # Build time test only, enabled by CONFIG_OF_ALL_DTBS
 k3-am625-beagleplay-csi2-ov5640-dtbs := k3-am625-beagleplay.dtb \
@@ -148,6 +149,8 @@ k3-j721s2-evm-pcie1-ep-dtbs := k3-j721s2-common-proc-board.dtb \
 	k3-j721s2-evm-pcie1-ep.dtbo
 k3-j784s4-evm-quad-port-eth-exp1-dtbs := k3-j784s4-evm.dtb \
 	k3-j784s4-evm-quad-port-eth-exp1.dtbo
+k3-j784s4-evm-usxgmii-exp1-exp2.dtbs := k3-j784s4-evm.dtb \
+	k3-j784s4-evm-usxgmii-exp1-exp2.dtbo
 dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
 	k3-am625-beagleplay-csi2-tevi-ov5640.dtb \
 	k3-am625-sk-csi2-imx219.dtb \
@@ -169,7 +172,8 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
 	k3-j721e-evm-pcie0-ep.dtb \
 	k3-j721e-sk-csi2-dual-imx219-dtbs \
 	k3-j721s2-evm-pcie1-ep.dtb \
-	k3-j784s4-evm-quad-port-eth-exp1.dtb
+	k3-j784s4-evm-quad-port-eth-exp1.dtb \
+	k3-j784s4-evm-usxgmii-exp1-exp2.dtb
 
 # Enable support for device-tree overlays
 DTC_FLAGS_k3-am625-beagleplay += -@
diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso b/arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso
new file mode 100644
index 000000000000..b8e7fed6105a
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-j784s4-evm-usxgmii-exp1-exp2.dtso
@@ -0,0 +1,81 @@
+/* SPDX-License-Identifier: GPL-2.0-only OR MIT */
+/**
+ * DT Overlay for CPSW9G in dual port fixed-link USXGMII mode using ENET-1
+ * and ENET-2 Expansion slots of J784S4 EVM.
+ *
+ * Copyright (C) 2024 Texas Instruments Incorporated - https://www.ti.com/
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/phy/phy-cadence.h>
+#include <dt-bindings/phy/phy.h>
+
+#include "k3-serdes.h"
+
+&{/} {
+	aliases {
+		ethernet1 = "/bus@100000/ethernet@c000000/ethernet-ports/port@1";
+		ethernet2 = "/bus@100000/ethernet@c000000/ethernet-ports/port@2";
+		ethernet3 = "/bus@100000/ethernet@c200000/ethernet-ports/port@1";
+	};
+};
+
+&main_cpsw0 {
+	status = "okay";
+	pinctrl-names = "default";
+};
+
+&main_cpsw0_port1 {
+	status = "okay";
+	phy-mode = "usxgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 1>, <&serdes2_usxgmii_link>;
+	phy-names = "mac", "serdes";
+	fixed-link {
+		speed = <5000>;
+		full-duplex;
+	};
+};
+
+&main_cpsw0_port2 {
+	status = "okay";
+	phy-mode = "usxgmii";
+	mac-address = [00 00 00 00 00 00];
+	phys = <&cpsw0_phy_gmii_sel 2>, <&serdes2_usxgmii_link>;
+	phy-names = "mac", "serdes";
+	fixed-link {
+		speed = <5000>;
+		full-duplex;
+	};
+};
+
+&serdes_wiz2 {
+	status = "okay";
+	assigned-clock-parents = <&k3_clks 406 9>; /* Use 156.25 MHz clock for USXGMII */
+};
+
+&serdes2 {
+	status = "okay";
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	serdes2_usxgmii_link: phy@2 {
+		reg = <2>;
+		cdns,num-lanes = <2>;
+		#phy-cells = <0>;
+		cdns,phy-type = <PHY_TYPE_USXGMII>;
+		resets = <&serdes_wiz2 3>, <&serdes_wiz2 4>;
+	};
+};
+
+&serdes_ln_ctrl {
+	idle-states = <J784S4_SERDES0_LANE0_PCIE1_LANE0>, <J784S4_SERDES0_LANE1_PCIE1_LANE1>,
+		      <J784S4_SERDES0_LANE2_IP3_UNUSED>, <J784S4_SERDES0_LANE3_USB>,
+		      <J784S4_SERDES1_LANE0_PCIE0_LANE0>, <J784S4_SERDES1_LANE1_PCIE0_LANE1>,
+		      <J784S4_SERDES1_LANE2_PCIE0_LANE2>, <J784S4_SERDES1_LANE3_PCIE0_LANE3>,
+		      <J784S4_SERDES2_LANE0_IP2_UNUSED>, <J784S4_SERDES2_LANE1_IP2_UNUSED>,
+		      <J784S4_SERDES2_LANE2_QSGMII_LANE1>, <J784S4_SERDES2_LANE3_QSGMII_LANE2>;
+};
-- 
2.34.1


_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

Re: [PATCH v5 4/5] arm64: dts: ti: k3-j784s4: Add overlay to enable QSGMII mode with CPSW9G

[Nishanth Menon]

On 12:51-20240314, Chintan Vankar wrote:
> +&serdes2 {
> +	status = "okay";
> +	#address-cells = <1>;
> +	#size-cells = <0>;

Here and elsewhere
Please follow https://docs.kernel.org/devicetree/bindings/dts-coding-style.html#order-of-properties-in-device-node

> +	serdes2_qsgmii_link: phy@0 {
> +		reg = <2>;
> +		cdns,num-lanes = <1>;
> +		#phy-cells = <0>;
> +		cdns,phy-type = <PHY_TYPE_QSGMII>;
> +		resets = <&serdes_wiz2 3>;
> +	};
> +};

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel