[PATCH 0/6] arm64: dts: imx8mp-skov: add new variants

[PATCH 0/6] arm64: dts: imx8mp-skov: add new variants

[Ahmad Fatoum]

The Skov i.MX8MP boards are a family of climate controllers.

There are already device trees for three board variants and this series
adds support for three more:

- Basic: Barebones DT for use as bootloader device tree and as fallback
    when a device is unknown
  - BD500: No touch screen, but a few LEDs on the front plate
  - TIAN G07017: with a 7" touch screen

---
Ahmad Fatoum (5):
      dt-bindings: arm: fsl: add more compatibles for Skov i.MX8MP variants
      arm64: dts: imx8mp-skov: move I2C2 pin control group into DTSI
      arm64: dts: imx8mp-skov: describe I2C bus recovery for all controllers
      arm64: dts: imx8mp-skov: add revC BD500 board
      arm64: dts: imx8mp-skov: support new 7" panel board

Oleksij Rempel (1):
      arm64: dts: imx8mp-skov: add basic board as fallback

 Documentation/devicetree/bindings/arm/fsl.yaml     |  3 +
 arch/arm64/boot/dts/freescale/Makefile             |  3 +
 .../arm64/boot/dts/freescale/imx8mp-skov-basic.dts | 10 +++
 .../arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi | 58 +++++++++++++-
 .../freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts  | 11 ---
 .../boot/dts/freescale/imx8mp-skov-revc-bd500.dts  | 91 ++++++++++++++++++++++
 .../dts/freescale/imx8mp-skov-revc-tian-g07017.dts | 81 +++++++++++++++++++
 7 files changed, 243 insertions(+), 14 deletions(-)
---
base-commit: 37136bf5c3a6f6b686d74f41837a6406bec6b7bc
change-id: 20250106-skov-imx8mp-new-boards-bba82044e96f

Best regards,
-- 
Ahmad Fatoum <a.fatoum@pengutronix.de>

[PATCH 1/6] dt-bindings: arm: fsl: add more compatibles for Skov i.MX8MP variants

[Ahmad Fatoum]

The Skov i.MX8MP boards are a family of climate controllers.

In preparation for adding device trees for three more variants,
describe their DT compatible in the bindings.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 Documentation/devicetree/bindings/arm/fsl.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml
index 3713175548637ec17561c068932123c558776435..0adc5495622ee788ac310bd8e48ef9f83b59735f 100644
--- a/Documentation/devicetree/bindings/arm/fsl.yaml
+++ b/Documentation/devicetree/bindings/arm/fsl.yaml
@@ -1097,9 +1097,12 @@ properties:
               - gateworks,imx8mp-gw74xx   # i.MX8MP Gateworks Board
               - gateworks,imx8mp-gw75xx-2x # i.MX8MP Gateworks Board
               - gateworks,imx8mp-gw82xx-2x # i.MX8MP Gateworks Board
+              - skov,imx8mp-skov-basic # SKOV i.MX8MP baseboard without frontplate
               - skov,imx8mp-skov-revb-hdmi # SKOV i.MX8MP climate control without panel
               - skov,imx8mp-skov-revb-lt6 # SKOV i.MX8MP climate control with 7” panel
               - skov,imx8mp-skov-revb-mi1010ait-1cp1 # SKOV i.MX8MP climate control with 10.1" panel
+              - skov,imx8mp-skov-revc-bd500 # SKOV i.MX8MP climate control with LED frontplate
+              - skov,imx8mp-skov-revc-tian-g07017 # SKOV i.MX8MP climate control with LED frontplate
               - toradex,verdin-imx8mp     # Verdin iMX8M Plus Modules
               - toradex,verdin-imx8mp-nonwifi  # Verdin iMX8M Plus Modules without Wi-Fi / BT
               - toradex,verdin-imx8mp-wifi  # Verdin iMX8M Plus Wi-Fi / BT Modules

-- 
2.39.5

Re: [PATCH 1/6] dt-bindings: arm: fsl: add more compatibles for Skov i.MX8MP variants

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 363 bytes --]

On Mon, Jan 13, 2025 at 11:29:05PM +0100, Ahmad Fatoum wrote:
> The Skov i.MX8MP boards are a family of climate controllers.
> 
> In preparation for adding device trees for three more variants,
> describe their DT compatible in the bindings.
> 
> Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>

Acked-by: Conor Dooley <conor.dooley@microchip.com>

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

[PATCH 2/6] arm64: dts: imx8mp-skov: add basic board as fallback

[Ahmad Fatoum]

From: Oleksij Rempel <o.rempel@pengutronix.de>

All Skov i.MX8MP boards share the same baseboard (modulo revisions)
and are booted with the same bootloader image, which samples some
strapping pins at startup and determines which kernel device tree
to use.

For use as bootloader device tree and as fallback, when no matching
device tree has been found, add a basic variant that doesn't configure
any variant-specific peripherals like displays.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 arch/arm64/boot/dts/freescale/Makefile              |  1 +
 arch/arm64/boot/dts/freescale/imx8mp-skov-basic.dts | 10 ++++++++++
 2 files changed, 11 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 839432153cc7ae15d3c1e668c0cb192d5563b996..ea4da899b44be0aaac745f6a0503bed3bb8ba20c 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -193,6 +193,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-nitrogen-smarc-universal-board.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
 imx8mp-phyboard-pollux-rdk-no-eth-dtbs += imx8mp-phyboard-pollux-rdk.dtb imx8mp-phycore-no-eth.dtbo
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk-no-eth.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-basic.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-mi1010ait-1cp1.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-basic.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-basic.dts
new file mode 100644
index 0000000000000000000000000000000000000000..5a2629f3567c6ce664ddad9a49f51829b3f54bd5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-basic.dts
@@ -0,0 +1,10 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "imx8mp-skov-reva.dtsi"
+
+/ {
+	model = "SKOV IMX8MP CPU basic/fallback";
+	compatible = "skov,imx8mp-skov-basic", "fsl,imx8mp";
+};

-- 
2.39.5

[PATCH 3/6] arm64: dts: imx8mp-skov: move I2C2 pin control group into DTSI

[Ahmad Fatoum]

I2C2 is exposed on a pin header on the base board, so its pinmux is
always the same if it's enabled.

Therefore, move the definition to the common DTSI, so board DTs only
need to override the status to enable it.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi          | 12 ++++++++++++
 .../boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts   | 11 -----------
 2 files changed, 12 insertions(+), 11 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi
index 59813ef8e2bb3a3d5672ba1c5776cf0e45fb6862..9dca829581137bc0c3026caf7cda112b859ec092 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi
@@ -314,6 +314,11 @@ reg_nvcc_sd2: LDO5 {
 	};
 };
 
+&i2c2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_i2c2>;
+};
+
 &i2c3 {
 	clock-frequency = <100000>;
 	pinctrl-names = "default";
@@ -538,6 +543,13 @@ MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA				0x400001c2
 		>;
 	};
 
+	pinctrl_i2c2: i2c2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL				0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA				0x400001c2
+		>;
+	};
+
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL				0x400001c2
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts
index 2c75da5f064f2b0cd97f5040febac13c4adc020b..ba581765b52298ea26a5a63079c08f39f10e4e3b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revb-mi1010ait-1cp1.dts
@@ -27,8 +27,6 @@ &backlight {
 
 &i2c2 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_i2c2>;
 	status = "okay";
 
 	touchscreen@38 {
@@ -90,12 +88,3 @@ &reg_tft_vcom {
 	voltage-table = <3160000 73>;
 	status = "okay";
 };
-
-&iomuxc {
-	pinctrl_i2c2: i2c2grp {
-		fsl,pins = <
-			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL				0x400001c2
-			MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA				0x400001c2
-		>;
-	};
-};

-- 
2.39.5

[PATCH 4/6] arm64: dts: imx8mp-skov: describe I2C bus recovery for all controllers

[Ahmad Fatoum]

I2C bus recovery can be used to recover when SCL/SDA are stuck low.
To be able to use it, add the necessary GPIO and pinctrl entries.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 .../arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi | 48 ++++++++++++++++++++--
 1 file changed, 44 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi
index 9dca829581137bc0c3026caf7cda112b859ec092..47087624e557c9c961ec4479cee4fedac6328748 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-reva.dtsi
@@ -222,8 +222,11 @@ &flexcan2 {
 
 &i2c1 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c1>;
+	pinctrl-1 = <&pinctrl_i2c1_gpio>;
+	scl-gpios = <&gpio5 14 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 15 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	pmic@25 {
@@ -315,14 +318,20 @@ reg_nvcc_sd2: LDO5 {
 };
 
 &i2c2 {
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c2>;
+	pinctrl-1 = <&pinctrl_i2c2_gpio>;
+	scl-gpios = <&gpio5 16 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 17 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 };
 
 &i2c3 {
 	clock-frequency = <100000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c3>;
+	pinctrl-1 = <&pinctrl_i2c3_gpio>;
+	scl-gpios = <&gpio5 18 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 19 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	i2c_rtc: rtc@51 {
@@ -337,8 +346,11 @@ i2c_rtc: rtc@51 {
 
 &i2c4 {
 	clock-frequency = <380000>;
-	pinctrl-names = "default";
+	pinctrl-names = "default", "gpio";
 	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
 	status = "okay";
 
 	switch: switch@5f {
@@ -543,6 +555,13 @@ MX8MP_IOMUXC_I2C1_SDA__I2C1_SDA				0x400001c2
 		>;
 	};
 
+	pinctrl_i2c1_gpio: i2c1gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C1_SCL__GPIO5_IO14			0x400001c2
+			MX8MP_IOMUXC_I2C1_SDA__GPIO5_IO15			0x400001c2
+		>;
+	};
+
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_I2C2_SCL__I2C2_SCL				0x400001c2
@@ -550,6 +569,13 @@ MX8MP_IOMUXC_I2C2_SDA__I2C2_SDA				0x400001c2
 		>;
 	};
 
+	pinctrl_i2c2_gpio: i2c2gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C2_SCL__GPIO5_IO16			0x400001c2
+			MX8MP_IOMUXC_I2C2_SDA__GPIO5_IO17			0x400001c2
+		>;
+	};
+
 	pinctrl_i2c3: i2c3grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_I2C3_SCL__I2C3_SCL				0x400001c2
@@ -557,6 +583,13 @@ MX8MP_IOMUXC_I2C3_SDA__I2C3_SDA				0x400001c2
 		>;
 	};
 
+	pinctrl_i2c3_gpio: i2c3gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C3_SCL__GPIO5_IO18			0x400001c2
+			MX8MP_IOMUXC_I2C3_SDA__GPIO5_IO19			0x400001c2
+		>;
+	};
+
 	pinctrl_i2c4: i2c4grp {
 		fsl,pins = <
 			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL				0x400001c3
@@ -564,6 +597,13 @@ MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA				0x400001c3
 		>;
 	};
 
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20			0x400001c3
+			MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21			0x400001c3
+		>;
+	};
+
 	pinctrl_pmic: pmicirqgrp {
 		fsl,pins = <
 			MX8MP_IOMUXC_GPIO1_IO03__GPIO1_IO03			0x41

-- 
2.39.5

[PATCH 5/6] arm64: dts: imx8mp-skov: add revC BD500 board

[Ahmad Fatoum]

The BD500 replaces the touch display with 3 bicolor LEDs and a push
button on top of a Skov i.MX8-CPU revision C.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
 arch/arm64/boot/dts/freescale/Makefile             |  1 +
 .../boot/dts/freescale/imx8mp-skov-revc-bd500.dts  | 91 ++++++++++++++++++++++
 2 files changed, 92 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index ea4da899b44be0aaac745f6a0503bed3bb8ba20c..6ee3a7ffe4792106118b8201c1f5f51c8ecd0ff2 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -197,6 +197,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-basic.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-mi1010ait-1cp1.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revc-bd500.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mp-ras314.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-var-som-symphony.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revc-bd500.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revc-bd500.dts
new file mode 100644
index 0000000000000000000000000000000000000000..b816c6cd3bca60b14cf6bc7f40cb780aa893958d
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revc-bd500.dts
@@ -0,0 +1,91 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "imx8mp-skov-reva.dtsi"
+
+/ {
+	model = "SKOV IMX8MP CPU revC - bd500";
+	compatible = "skov,imx8mp-skov-revc-bd500", "fsl,imx8mp";
+
+	leds {
+		led_system_red: led-3 {
+			label = "bd500:system:red";
+			color = <LED_COLOR_ID_RED>;
+			/* Inverted compared to others due to NMOS inverter */
+			gpios = <&gpioexp 3 GPIO_ACTIVE_HIGH>;
+			default-state = "off";
+		};
+
+		led_system_green: led-4 {
+			label = "bd500:system:green";
+			color = <LED_COLOR_ID_GREEN>;
+			gpios = <&gpioexp 2 GPIO_ACTIVE_LOW>;
+			default-state = "on";
+		};
+
+		led_lan1_red: led-5 {
+			label = "bd500:lan1:act";
+			color = <LED_COLOR_ID_RED>;
+			linux,default-trigger = "netdev";
+			gpios = <&gpioexp 1 GPIO_ACTIVE_LOW>;
+		};
+
+		led_lan1_green: led-6 {
+			label = "bd500:lan1:link";
+			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "netdev";
+			gpios = <&gpioexp 0 GPIO_ACTIVE_LOW>;
+		};
+
+		led_lan2_red: led-7 {
+			label = "bd500:lan2:act";
+			color = <LED_COLOR_ID_RED>;
+			linux,default-trigger = "netdev";
+			gpios = <&gpioexp 6 GPIO_ACTIVE_LOW>;
+		};
+
+		led_lan2_green: led-8 {
+			label = "bd500:lan2:link";
+			color = <LED_COLOR_ID_GREEN>;
+			linux,default-trigger = "netdev";
+			gpios = <&gpioexp 7 GPIO_ACTIVE_LOW>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		button-1 {
+			label = "S1";
+			linux,code = <KEY_CONFIG>;
+			gpios = <&gpioexp 5 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	gpioexp: gpio@20 {
+		compatible = "nxp,pca6408";
+		reg = <0x20>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_exp>;
+		interrupts-extended = <&gpio4 28 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio4 29 GPIO_ACTIVE_LOW>;
+		vcc-supply = <&reg_vdd_3v3>;
+		gpio-controller;
+		#gpio-cells = <2>;
+	};
+};
+
+&iomuxc {
+	pinctrl_gpio_exp: gpioexpgrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28	0x0
+			MX8MP_IOMUXC_SAI3_RXC__GPIO4_IO29	0x0
+		>;
+	};
+};

-- 
2.39.5

[PATCH 6/6] arm64: dts: imx8mp-skov: support new 7" panel board

[Ahmad Fatoum]

This board is very similar to the already upstream
imx8mp-skov-revb-mi1010ait-1cp1.dts with the difference that it uses a
different 7" LVDS panel.

Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
---
Note: The panel's binding is already in linux-next.
---
 arch/arm64/boot/dts/freescale/Makefile             |  1 +
 .../dts/freescale/imx8mp-skov-revc-tian-g07017.dts | 81 ++++++++++++++++++++++
 2 files changed, 82 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 6ee3a7ffe4792106118b8201c1f5f51c8ecd0ff2..986c4f974da51fb8a6fb3bc7be1ec664f7db629e 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -198,6 +198,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-lt6.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-mi1010ait-1cp1.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revc-bd500.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revc-tian-g07017.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mpxl.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-tqma8mpql-mba8mp-ras314.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-var-som-symphony.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-skov-revc-tian-g07017.dts b/arch/arm64/boot/dts/freescale/imx8mp-skov-revc-tian-g07017.dts
new file mode 100644
index 0000000000000000000000000000000000000000..9a562c011f2c292861c2e57e0e74aa3acd063e0c
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-skov-revc-tian-g07017.dts
@@ -0,0 +1,81 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+
+/dts-v1/;
+
+#include "imx8mp-skov-reva.dtsi"
+
+/ {
+	model = "SKOV IMX8MP CPU revC - TIAN G07017";
+	compatible = "skov,imx8mp-skov-revc-tian-g07017", "fsl,imx8mp";
+
+	panel {
+		compatible = "topland,tian-g07017-01";
+		backlight = <&backlight>;
+		power-supply = <&reg_tft_vcom>;
+
+		port {
+			in_lvds0: endpoint {
+				remote-endpoint = <&ldb_lvds_ch0>;
+			};
+		};
+	};
+};
+
+&backlight {
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	touchscreen@38 {
+		compatible = "edt,edt-ft5506";
+		reg = <0x38>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_touchscreen>;
+		interrupts-extended = <&gpio4 28 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&gpio4 29 GPIO_ACTIVE_LOW>;
+		touchscreen-size-x = <1024>;
+		touchscreen-size-y = <600>;
+		vcc-supply = <&reg_vdd_3v3>;
+		iovcc-supply = <&reg_vdd_3v3>;
+		wakeup-source;
+	};
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&lvds_bridge {
+	assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>,
+				 <&clk IMX8MP_VIDEO_PLL1>;
+	assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
+	/* IMX8MP_VIDEO_PLL1 = IMX8MP_CLK_MEDIA_DISP2_PIX * 2 * 7 */
+	assigned-clock-rates = <0>, <358400000>;
+	status = "okay";
+
+	ports {
+		port@1 {
+			ldb_lvds_ch0: endpoint {
+				remote-endpoint = <&in_lvds0>;
+			};
+		};
+	};
+};
+
+&pwm4 {
+	status = "okay";
+};
+
+&pwm1 {
+	status = "okay";
+};
+
+&reg_tft_vcom {
+	regulator-min-microvolt = <3160000>;
+	regulator-max-microvolt = <3160000>;
+	voltage-table = <3160000 73>;
+	status = "okay";
+};

-- 
2.39.5