[PATCH v2] arm64: defconfig: Enable TISCI Interrupt Router and Aggregator

[PATCH v2] arm64: defconfig: Enable TISCI Interrupt Router and Aggregator

[Vaishnav Achath]

Enable TISCI Interrupt Router and Interrupt Aggregator drivers.
These IPs are found in all TI K3 SoCs like J721E, AM62X and is required
for core functionality like DMA, GPIO Interrupts which is necessary
during boot, thus make them built-in.

bloat-o-meter summary on vmlinux:
	add/remove: 460/1 grow/shrink: 4/0 up/down: 162483/-8 (162475)
	...
	Total: Before=31615984, After=31778459, chg +0.51%

Fixes: 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
Fixes: b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")

Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
---

V1 : https://lore.kernel.org/all/20250119182121.3956546-1-vaishnav.a@ti.com/

V1->V2:
	* Add Fixes tag.
	* Add bloat-o-meter summary to commit message.

Previously both of these configs were selected for ARCH_K3 in respective
Kconfigs, but commit b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
and commit 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
in dropped this recently without adding those back in arm64
defconfig, this causes boot failure in all TI K3 platforms.

Passing bootlog with configs enabled:
https://gist.github.com/vaishnavachath/03d8d3ce0f22219643c2f4d1dd243fd1

 arch/arm64/configs/defconfig | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index cb7da4415599..1f25423de383 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1551,6 +1551,8 @@ CONFIG_PWM_VISCONTI=m
 CONFIG_SL28CPLD_INTC=y
 CONFIG_QCOM_PDC=y
 CONFIG_QCOM_MPM=y
+CONFIG_TI_SCI_INTR_IRQCHIP=y
+CONFIG_TI_SCI_INTA_IRQCHIP=y
 CONFIG_RESET_GPIO=m
 CONFIG_RESET_IMX7=y
 CONFIG_RESET_QCOM_AOSS=y
-- 
2.34.1

Re: [PATCH v2] arm64: defconfig: Enable TISCI Interrupt Router and Aggregator

[Geert Uytterhoeven]

Hi Vaishnav,

Thanks for your patch!

On Mon, 3 Feb 2025 at 16:08, Vaishnav Achath <vaishnav.a@ti.com> wrote:
> Enable TISCI Interrupt Router and Interrupt Aggregator drivers.
> These IPs are found in all TI K3 SoCs like J721E, AM62X and is required
> for core functionality like DMA, GPIO Interrupts which is necessary
> during boot, thus make them built-in.
>
> bloat-o-meter summary on vmlinux:
>         add/remove: 460/1 grow/shrink: 4/0 up/down: 162483/-8 (162475)
>         ...
>         Total: Before=31615984, After=31778459, chg +0.51%

My first thought was: that's a hefty size increase for two rather
small drivers!  So I enabled these two options in one of my own kernel
configs, and saw a size increase of only 7872 bytes...

> Fixes: 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
> Fixes: b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
>
> Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
> ---
>
> V1 : https://lore.kernel.org/all/20250119182121.3956546-1-vaishnav.a@ti.com/
>
> V1->V2:
>         * Add Fixes tag.
>         * Add bloat-o-meter summary to commit message.
>
> Previously both of these configs were selected for ARCH_K3 in respective
> Kconfigs, but commit b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
> and commit 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
> in dropped this recently without adding those back in arm64
> defconfig, this causes boot failure in all TI K3 platforms.
>
> Passing bootlog with configs enabled:
> https://gist.github.com/vaishnavachath/03d8d3ce0f22219643c2f4d1dd243fd1
>
>  arch/arm64/configs/defconfig | 2 ++
>  1 file changed, 2 insertions(+)
>
> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> index cb7da4415599..1f25423de383 100644
> --- a/arch/arm64/configs/defconfig
> +++ b/arch/arm64/configs/defconfig
> @@ -1551,6 +1551,8 @@ CONFIG_PWM_VISCONTI=m
>  CONFIG_SL28CPLD_INTC=y
>  CONFIG_QCOM_PDC=y
>  CONFIG_QCOM_MPM=y
> +CONFIG_TI_SCI_INTR_IRQCHIP=y
> +CONFIG_TI_SCI_INTA_IRQCHIP=y
>  CONFIG_RESET_GPIO=m
>  CONFIG_RESET_IMX7=y
>  CONFIG_RESET_QCOM_AOSS=y

However, on arm64 defconfig, this has indeed a much bigger impact,
as it also (re)enables several other drivers that depend on the
irqchip symbols.

You probably want to mention that in the commit message...

Gr{oetje,eeting}s,

                        Geert

-- 
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org

In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
                                -- Linus Torvalds

Re: [PATCH v2] arm64: defconfig: Enable TISCI Interrupt Router and Aggregator

[Nishanth Menon]

On 08:42-20250204, Geert Uytterhoeven wrote:
> Hi Vaishnav,
> 
> Thanks for your patch!
> 
> On Mon, 3 Feb 2025 at 16:08, Vaishnav Achath <vaishnav.a@ti.com> wrote:
> > Enable TISCI Interrupt Router and Interrupt Aggregator drivers.
> > These IPs are found in all TI K3 SoCs like J721E, AM62X and is required
> > for core functionality like DMA, GPIO Interrupts which is necessary
> > during boot, thus make them built-in.
> >
> > bloat-o-meter summary on vmlinux:
> >         add/remove: 460/1 grow/shrink: 4/0 up/down: 162483/-8 (162475)
> >         ...
> >         Total: Before=31615984, After=31778459, chg +0.51%
> 
> My first thought was: that's a hefty size increase for two rather
> small drivers!  So I enabled these two options in one of my own kernel
> configs, and saw a size increase of only 7872 bytes...
> 
> > Fixes: 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
> > Fixes: b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
> >
> > Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
> > ---
> >
> > V1 : https://lore.kernel.org/all/20250119182121.3956546-1-vaishnav.a@ti.com/
> >
> > V1->V2:
> >         * Add Fixes tag.
> >         * Add bloat-o-meter summary to commit message.
> >
> > Previously both of these configs were selected for ARCH_K3 in respective
> > Kconfigs, but commit b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
> > and commit 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
> > in dropped this recently without adding those back in arm64
> > defconfig, this causes boot failure in all TI K3 platforms.
> >
> > Passing bootlog with configs enabled:
> > https://gist.github.com/vaishnavachath/03d8d3ce0f22219643c2f4d1dd243fd1
> >
> >  arch/arm64/configs/defconfig | 2 ++
> >  1 file changed, 2 insertions(+)
> >
> > diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
> > index cb7da4415599..1f25423de383 100644
> > --- a/arch/arm64/configs/defconfig
> > +++ b/arch/arm64/configs/defconfig
> > @@ -1551,6 +1551,8 @@ CONFIG_PWM_VISCONTI=m
> >  CONFIG_SL28CPLD_INTC=y
> >  CONFIG_QCOM_PDC=y
> >  CONFIG_QCOM_MPM=y
> > +CONFIG_TI_SCI_INTR_IRQCHIP=y
> > +CONFIG_TI_SCI_INTA_IRQCHIP=y
> >  CONFIG_RESET_GPIO=m
> >  CONFIG_RESET_IMX7=y
> >  CONFIG_RESET_QCOM_AOSS=y
> 
> However, on arm64 defconfig, this has indeed a much bigger impact,
> as it also (re)enables several other drivers that depend on the
> irqchip symbols.
> 
> You probably want to mention that in the commit message...

Thanks Geert and I agree. This however just restores the status quo as
it was in 6.13 tag kernel (and ofcourse the default boot status).

Will be good to mention that as well - in effect, we are just restoring
the behavior, not introducing new features.

Side note: We are still working towards fixing up other driver modules
and some time in near future, hope to transition to initramfs boot as
default in a single patch.. but till then let us maintain the status
quo.

-- 
Regards,
Nishanth Menon
Key (0xDDB5849D1736249D) / Fingerprint: F8A2 8693 54EB 8232 17A3  1A34 DDB5 849D 1736 249D

Re: [PATCH v2] arm64: defconfig: Enable TISCI Interrupt Router and Aggregator

[Vaishnav Achath]

Hi Geert, Nishanth,

On 05/02/25 09:21, Nishanth Menon wrote:
> On 08:42-20250204, Geert Uytterhoeven wrote:
>> Hi Vaishnav,
>>
>> Thanks for your patch!
>>
>> On Mon, 3 Feb 2025 at 16:08, Vaishnav Achath <vaishnav.a@ti.com> wrote:
>>> Enable TISCI Interrupt Router and Interrupt Aggregator drivers.
>>> These IPs are found in all TI K3 SoCs like J721E, AM62X and is required
>>> for core functionality like DMA, GPIO Interrupts which is necessary
>>> during boot, thus make them built-in.
>>>
>>> bloat-o-meter summary on vmlinux:
>>>          add/remove: 460/1 grow/shrink: 4/0 up/down: 162483/-8 (162475)
>>>          ...
>>>          Total: Before=31615984, After=31778459, chg +0.51%
>>
>> My first thought was: that's a hefty size increase for two rather
>> small drivers!  So I enabled these two options in one of my own kernel
>> configs, and saw a size increase of only 7872 bytes...
>>
>>> Fixes: 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
>>> Fixes: b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
>>>
>>> Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
>>> ---
>>>
>>> V1 : https://lore.kernel.org/all/20250119182121.3956546-1-vaishnav.a@ti.com/
>>>
>>> V1->V2:
>>>          * Add Fixes tag.
>>>          * Add bloat-o-meter summary to commit message.
>>>
>>> Previously both of these configs were selected for ARCH_K3 in respective
>>> Kconfigs, but commit b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
>>> and commit 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
>>> in dropped this recently without adding those back in arm64
>>> defconfig, this causes boot failure in all TI K3 platforms.
>>>
>>> Passing bootlog with configs enabled:
>>> https://gist.github.com/vaishnavachath/03d8d3ce0f22219643c2f4d1dd243fd1
>>>
>>>   arch/arm64/configs/defconfig | 2 ++
>>>   1 file changed, 2 insertions(+)
>>>
>>> diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
>>> index cb7da4415599..1f25423de383 100644
>>> --- a/arch/arm64/configs/defconfig
>>> +++ b/arch/arm64/configs/defconfig
>>> @@ -1551,6 +1551,8 @@ CONFIG_PWM_VISCONTI=m
>>>   CONFIG_SL28CPLD_INTC=y
>>>   CONFIG_QCOM_PDC=y
>>>   CONFIG_QCOM_MPM=y
>>> +CONFIG_TI_SCI_INTR_IRQCHIP=y
>>> +CONFIG_TI_SCI_INTA_IRQCHIP=y
>>>   CONFIG_RESET_GPIO=m
>>>   CONFIG_RESET_IMX7=y
>>>   CONFIG_RESET_QCOM_AOSS=y
>>
>> However, on arm64 defconfig, this has indeed a much bigger impact,
>> as it also (re)enables several other drivers that depend on the
>> irqchip symbols.
>>
>> You probably want to mention that in the commit message...
> 
> Thanks Geert and I agree. This however just restores the status quo as
> it was in 6.13 tag kernel (and ofcourse the default boot status).
> 
> Will be good to mention that as well - in effect, we are just restoring
> the behavior, not introducing new features.
> 

Thank you for the feedback, I have sent a v3 with updated commit message 
mentioning the reason for size increase and that we are reinstating 
previous behavior, all the dependencies getting re-enabled were already 
part of the arm64 defconfig.

V3 - https://lore.kernel.org/all/20250205062229.3869081-1-vaishnav.a@ti.com/

Thanks and Regards,
Vaishnav

> Side note: We are still working towards fixing up other driver modules
> and some time in near future, hope to transition to initramfs boot as
> default in a single patch.. but till then let us maintain the status
> quo.
> 

Re: [PATCH v2] arm64: defconfig: Enable TISCI Interrupt Router and Aggregator

[Dhruva Gole]

On Feb 03, 2025 at 20:38:01 +0530, Vaishnav Achath wrote:
> Enable TISCI Interrupt Router and Interrupt Aggregator drivers.
> These IPs are found in all TI K3 SoCs like J721E, AM62X and is required
> for core functionality like DMA, GPIO Interrupts which is necessary
> during boot, thus make them built-in.
> 
> bloat-o-meter summary on vmlinux:
> 	add/remove: 460/1 grow/shrink: 4/0 up/down: 162483/-8 (162475)
> 	...
> 	Total: Before=31615984, After=31778459, chg +0.51%
> 
> Fixes: 2d95ffaecbc2 ("irqchip/ti-sci-intr: Add module build support")
> Fixes: b8b26ae398c4 ("irqchip/ti-sci-inta : Add module build support")
> 
> Signed-off-by: Vaishnav Achath <vaishnav.a@ti.com>
> ---

Tested this for basic boot on TI K3 AM625-SK with next-20250204.
Tested-by: Dhruva Gole <d-gole@ti.com>

Also,
Reviewed-by: Dhruva Gole <d-gole@ti.com>

-- 
Best regards,
Dhruva Gole
Texas Instruments Incorporated