* [PATCH v7 1/8] media: subdev: Add set_pad_by_ep() callback to internal ops
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
@ 2026-07-02 16:03 ` Frank.Li
2026-07-02 16:03 ` [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper Frank.Li
` (6 subsequent siblings)
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:03 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel
From: Frank Li <Frank.Li@nxp.com>
Add a set_pad_by_ep() callback to struct v4l2_subdev_internal_ops. The
callback is invoked while parsing firmware node endpoints and allows
subdevice drivers to configure media pad properties based on endpoint
information.
Typical uses include setting media pad flags according to the endpoint's
port number or type, and validating that the endpoint configuration is
supported by the underlying hardware. This provides a common mechanism
for endpoint-aware pad initialization during graph construction.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change in v7
- add vep argument
change in v6
- new patch
---
include/media/v4l2-subdev.h | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/include/media/v4l2-subdev.h b/include/media/v4l2-subdev.h
index d256b7ec8f848..05b3ccfc856ee 100644
--- a/include/media/v4l2-subdev.h
+++ b/include/media/v4l2-subdev.h
@@ -34,6 +34,7 @@ struct v4l2_ctrl_handler;
struct v4l2_event;
struct v4l2_event_subscription;
struct v4l2_fh;
+struct v4l2_fwnode_endpoint;
struct v4l2_subdev;
struct v4l2_subdev_fh;
struct v4l2_subdev_stream_config;
@@ -935,6 +936,10 @@ struct v4l2_subdev_ops {
* the v4l2_subdev structure. It is almost certainly required for any
* sub-device that sets the V4L2_SUBDEV_FL_HAS_DEVNODE flag.
*
+ * @set_pad_by_ep: Set media pad information by parsed fwnode endpoint vep.
+ * return < 0 means can't support this type endpoint. Set
+ * pad->flags according to vep information.
+ *
* .. note::
* Never call this from drivers, only the v4l2 framework can call
* these ops.
@@ -947,6 +952,8 @@ struct v4l2_subdev_internal_ops {
int (*open)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh);
int (*close)(struct v4l2_subdev *sd, struct v4l2_subdev_fh *fh);
void (*release)(struct v4l2_subdev *sd);
+ int (*set_pad_by_ep)(struct v4l2_subdev *sd, struct media_pad *pad,
+ struct v4l2_fwnode_endpoint *vep);
};
/* Set this flag if this subdev is a i2c device. */
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
2026-07-02 16:03 ` [PATCH v7 1/8] media: subdev: Add set_pad_by_ep() callback to internal ops Frank.Li
@ 2026-07-02 16:03 ` Frank.Li
2026-07-02 16:15 ` Laurent Pinchart
2026-07-02 16:03 ` [PATCH v7 3/8] media: synopsys: Use v4l2_subdev_get_frame_desc_passthrough() Frank.Li
` (5 subsequent siblings)
7 siblings, 1 reply; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:03 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel
From: Frank Li <Frank.Li@nxp.com>
Add media_async_register_subdev(), a helper to register a V4L2 sub-device
with the asynchronous sub-device framework.
The helper requires each port to contain a single endpoint, with port
addresses starting at 0 and increasing consecutively.
During registration it parses the firmware graph, creates media pads for
all endpoints, and registers common asynchronous notifiers for sink
endpoints. These notifiers automatically create media links when the
corresponding remote source devices become available.
The set_pad_by_ep() callback allows drivers to determine the media pad
associated with a firmware endpoint and identify whether the endpoint
represents a sink pad.
By centralizing firmware graph parsing, media pad creation, notifier
registration, and link creation, this helper reduces duplicated code and
simplifies error handling in V4L2 sub-device drivers.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
change in v7
- don't use saved vep informaiton from media pand
- fix sashiko report problem
change in v6
- new patch
---
drivers/media/v4l2-core/v4l2-fwnode.c | 169 ++++++++++++++++++++++++++++++++++
include/media/v4l2-async.h | 39 ++++++++
2 files changed, 208 insertions(+)
diff --git a/drivers/media/v4l2-core/v4l2-fwnode.c b/drivers/media/v4l2-core/v4l2-fwnode.c
index 62a3a452f7884..4e15adc1af065 100644
--- a/drivers/media/v4l2-core/v4l2-fwnode.c
+++ b/drivers/media/v4l2-core/v4l2-fwnode.c
@@ -26,6 +26,7 @@
#include <media/v4l2-async.h>
#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mc.h>
#include <media/v4l2-subdev.h>
#include "v4l2-subdev-priv.h"
@@ -1302,6 +1303,174 @@ int __v4l2_async_register_subdev_sensor(struct v4l2_subdev *sd, struct module *m
}
EXPORT_SYMBOL_GPL(__v4l2_async_register_subdev_sensor);
+static int v4l2_common_notifier_bound(struct v4l2_async_notifier *notifier,
+ struct v4l2_subdev *sd,
+ struct v4l2_async_connection *asd)
+{
+ struct media_pad *pad = NULL;
+ struct fwnode_endpoint ep;
+ int ret;
+
+ if (asd->match.type != V4L2_ASYNC_MATCH_TYPE_FWNODE)
+ return -EINVAL;
+
+ if (!asd->match.fwnode)
+ return -EINVAL;
+
+ struct fwnode_handle *remote __free(fwnode_handle) =
+ fwnode_graph_get_remote_endpoint(asd->match.fwnode);
+
+ ret = fwnode_graph_parse_endpoint(remote, &ep);
+ if (ret)
+ return -EINVAL;
+
+ for (int i = 0; i < notifier->sd->entity.num_pads; i++) {
+ if (notifier->sd->entity.pads[i].index == ep.port) {
+ pad = ¬ifier->sd->entity.pads[i];
+ break;
+ }
+ }
+
+ if (!pad) {
+ dev_err(notifier->sd->dev, "failed to find sink pad\n");
+ return -EINVAL;
+ }
+
+ ret = v4l2_create_fwnode_links_to_pad(sd, pad, MEDIA_LNK_FL_ENABLED);
+ if (ret) {
+ dev_err(sd->dev, "failed to link source pad\n");
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct v4l2_async_notifier_operations v4l2_common_notifier_ops = {
+ .bound = v4l2_common_notifier_bound,
+};
+
+/*
+ * The only one endpoint under one port. And all ports number is continues.
+ */
+static int
+v4l2_async_nf_parse_fwnode(struct device *dev, struct media_pad *pads, u32 pads_count,
+ struct v4l2_async_notifier *notifier)
+{
+ struct v4l2_subdev *sd = notifier->sd;
+ struct v4l2_async_connection *asd;
+ struct v4l2_fwnode_endpoint vep;
+ struct media_pad *pad;
+ int ret;
+
+ if (!sd->internal_ops || !sd->internal_ops->set_pad_by_ep)
+ return dev_err_probe(dev, -EINVAL,
+ "Missed set_pad_by_ep() callback\n");
+ pad = pads;
+
+ fwnode_graph_for_each_endpoint_scoped(dev_fwnode(dev), ep) {
+ u32 flags;
+
+ ret = v4l2_fwnode_endpoint_parse(ep, &vep);
+ if (ret)
+ return dev_err_probe(dev, ret, "failed to parse endpoint\n");
+
+ if (vep.base.port >= pads_count)
+ return dev_err_probe(dev, -EINVAL,
+ "port number bigger than pad number\n");
+
+ pad = pads + vep.base.port;
+
+ ret = sd->internal_ops->set_pad_by_ep(sd, pad, &vep);
+ if (ret < 0)
+ return dev_err_probe(dev, ret, "Can support endpoint\n");
+
+ flags = pad->flags;
+
+ if (flags & MEDIA_PAD_FL_SOURCE)
+ continue; /* Bypass source port */
+
+ notifier->ops = &v4l2_common_notifier_ops;
+
+ asd = v4l2_async_nf_add_fwnode_remote(notifier, ep,
+ struct v4l2_async_connection);
+ if (IS_ERR(asd))
+ return dev_err_probe(dev, PTR_ERR(asd),
+ "failed to add notifier\n");
+ }
+
+ return 0;
+}
+
+void media_async_subdev_cleanup(struct v4l2_subdev *sd)
+{
+ v4l2_async_unregister_subdev(sd);
+ v4l2_subdev_cleanup(sd);
+ media_entity_cleanup(&sd->entity);
+ v4l2_async_nf_unregister(sd->subdev_notifier);
+ v4l2_async_nf_cleanup(sd->subdev_notifier);
+ kfree(sd->entity.pads);
+}
+EXPORT_SYMBOL_GPL(media_async_subdev_cleanup);
+
+int __media_async_register_subdev(struct v4l2_subdev *sd, struct module *module)
+{
+ struct device *dev = sd->dev;
+ u32 ep_count;
+ int ret;
+
+ if (WARN_ON(!sd->dev))
+ return -ENODEV;
+
+ struct v4l2_async_notifier *notifier __free(kfree) = kzalloc_obj(*notifier);
+ if (!notifier)
+ return -ENOMEM;
+
+ v4l2_async_subdev_nf_init(notifier, sd);
+
+ ep_count = fwnode_graph_get_endpoint_count(dev_fwnode(dev),
+ FWNODE_GRAPH_DEVICE_DISABLED);
+ if (!ep_count)
+ return dev_err_probe(dev, -EINVAL, "No connected endpoints\n");
+
+ struct media_pad *pads __free(kfree) = kzalloc_objs(struct media_pad, ep_count);
+ if (!pads)
+ return -ENOMEM;
+
+ ret = v4l2_async_nf_parse_fwnode(dev, pads, ep_count, notifier);
+ if (ret < 0)
+ goto out_cleanup;
+
+ ret = media_entity_pads_init(&sd->entity, ep_count, pads);
+ if (ret)
+ goto out_cleanup;
+
+ ret = v4l2_async_nf_register(notifier);
+ if (ret < 0)
+ goto out_cleanup;
+
+ ret = v4l2_subdev_init_finalize(sd);
+ if (ret)
+ goto out_unregister;
+
+ ret = __v4l2_async_register_subdev(sd, module);
+ if (ret < 0)
+ goto out_unregister;
+
+ sd->subdev_notifier = no_free_ptr(notifier);
+ retain_and_null_ptr(pads);
+
+ return 0;
+
+out_unregister:
+ v4l2_async_nf_unregister(notifier);
+ v4l2_subdev_cleanup(sd);
+out_cleanup:
+ v4l2_async_nf_cleanup(notifier);
+
+ return ret;
+}
+EXPORT_SYMBOL_GPL(__media_async_register_subdev);
+
MODULE_DESCRIPTION("V4L2 fwnode binding parsing library");
MODULE_LICENSE("GPL");
MODULE_AUTHOR("Sakari Ailus <sakari.ailus@linux.intel.com>");
diff --git a/include/media/v4l2-async.h b/include/media/v4l2-async.h
index 54a2d9620ed5b..ca41820f776c5 100644
--- a/include/media/v4l2-async.h
+++ b/include/media/v4l2-async.h
@@ -345,4 +345,43 @@ __v4l2_async_register_subdev_sensor(struct v4l2_subdev *sd, struct module *modul
* @sd: pointer to &struct v4l2_subdev
*/
void v4l2_async_unregister_subdev(struct v4l2_subdev *sd);
+
+enum v4l2_subdev_1to1_pads {
+ V4L2_SUBDEV_1TO1_PADS_SINK,
+ V4L2_SUBDEV_1TO1_PADS_SOURCE,
+ V4L2_SUBDEV_1TO1_PADS_TOTAL,
+};
+
+/**
+ * media_async_register_subdev - registers a sub-device to the asynchronous
+ * sub-device framework and parse set up common
+ * related devices
+ *
+ * @sd: pointer to struct &v4l2_subdev
+ *
+ * Register a V4L2 sub-device with the asynchronous sub-device framework.
+ * In addition to v4l2_async_register_subdev(), this function parses the
+ * firmware graph, creates media pads for the endpoints, and registers common
+ * notifiers to create media links between connected devices.
+ *
+ * This function also init media_pads.
+ *
+ * The sub-device is unregistered and cleanup by media_async_subdev_cleanup()
+ *
+ * While registered, the subdev module is marked as in-use.
+ *
+ * An error is returned if the module is no longer loaded on any attempts
+ * to register it.
+ */
+#define media_async_register_subdev(sd_1to1) \
+ __media_async_register_subdev(sd_1to1, THIS_MODULE)
+
+int __media_async_register_subdev(struct v4l2_subdev *sd_1to1, struct module *module);
+
+/**
+ * media_async_subdev_cleanup - unregistered and cleanup subdev and media pads
+ * @sd_1to1: pointer to struct &v4l2_subdev_1to1
+ */
+void media_async_subdev_cleanup(struct v4l2_subdev *sd_1to1);
+
#endif
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* Re: [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper
2026-07-02 16:03 ` [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper Frank.Li
@ 2026-07-02 16:15 ` Laurent Pinchart
2026-07-02 18:11 ` Frank Li
0 siblings, 1 reply; 13+ messages in thread
From: Laurent Pinchart @ 2026-07-02 16:15 UTC (permalink / raw)
To: Frank.Li
Cc: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch, Frank Li,
Martin Kepplinger-Novakovic, Rui Miguel Silva, Purism Kernel Team,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, linux-media, linux-kernel,
imx, Guoniu Zhou, devicetree, linux-arm-kernel
Hi Frank,
Have you missed the comment in v6 ?
https://lore.kernel.org/all/20260629084654.GB3054459@killaraus.ideasonboard.com/
On Thu, Jul 02, 2026 at 12:03:58PM -0400, Frank.Li@oss.nxp.com wrote:
> From: Frank Li <Frank.Li@nxp.com>
>
> Add media_async_register_subdev(), a helper to register a V4L2 sub-device
> with the asynchronous sub-device framework.
>
> The helper requires each port to contain a single endpoint, with port
> addresses starting at 0 and increasing consecutively.
>
> During registration it parses the firmware graph, creates media pads for
> all endpoints, and registers common asynchronous notifiers for sink
> endpoints. These notifiers automatically create media links when the
> corresponding remote source devices become available.
>
> The set_pad_by_ep() callback allows drivers to determine the media pad
> associated with a firmware endpoint and identify whether the endpoint
> represents a sink pad.
>
> By centralizing firmware graph parsing, media pad creation, notifier
> registration, and link creation, this helper reduces duplicated code and
> simplifies error handling in V4L2 sub-device drivers.
>
> Signed-off-by: Frank Li <Frank.Li@nxp.com>
> ---
> change in v7
> - don't use saved vep informaiton from media pand
> - fix sashiko report problem
>
> change in v6
> - new patch
> ---
> drivers/media/v4l2-core/v4l2-fwnode.c | 169 ++++++++++++++++++++++++++++++++++
> include/media/v4l2-async.h | 39 ++++++++
> 2 files changed, 208 insertions(+)
>
> diff --git a/drivers/media/v4l2-core/v4l2-fwnode.c b/drivers/media/v4l2-core/v4l2-fwnode.c
> index 62a3a452f7884..4e15adc1af065 100644
> --- a/drivers/media/v4l2-core/v4l2-fwnode.c
> +++ b/drivers/media/v4l2-core/v4l2-fwnode.c
> @@ -26,6 +26,7 @@
>
> #include <media/v4l2-async.h>
> #include <media/v4l2-fwnode.h>
> +#include <media/v4l2-mc.h>
> #include <media/v4l2-subdev.h>
>
> #include "v4l2-subdev-priv.h"
> @@ -1302,6 +1303,174 @@ int __v4l2_async_register_subdev_sensor(struct v4l2_subdev *sd, struct module *m
> }
> EXPORT_SYMBOL_GPL(__v4l2_async_register_subdev_sensor);
>
> +static int v4l2_common_notifier_bound(struct v4l2_async_notifier *notifier,
> + struct v4l2_subdev *sd,
> + struct v4l2_async_connection *asd)
> +{
> + struct media_pad *pad = NULL;
> + struct fwnode_endpoint ep;
> + int ret;
> +
> + if (asd->match.type != V4L2_ASYNC_MATCH_TYPE_FWNODE)
> + return -EINVAL;
> +
> + if (!asd->match.fwnode)
> + return -EINVAL;
> +
> + struct fwnode_handle *remote __free(fwnode_handle) =
> + fwnode_graph_get_remote_endpoint(asd->match.fwnode);
> +
> + ret = fwnode_graph_parse_endpoint(remote, &ep);
> + if (ret)
> + return -EINVAL;
> +
> + for (int i = 0; i < notifier->sd->entity.num_pads; i++) {
> + if (notifier->sd->entity.pads[i].index == ep.port) {
> + pad = ¬ifier->sd->entity.pads[i];
> + break;
> + }
> + }
> +
> + if (!pad) {
> + dev_err(notifier->sd->dev, "failed to find sink pad\n");
> + return -EINVAL;
> + }
> +
> + ret = v4l2_create_fwnode_links_to_pad(sd, pad, MEDIA_LNK_FL_ENABLED);
> + if (ret) {
> + dev_err(sd->dev, "failed to link source pad\n");
> + return ret;
> + }
> +
> + return 0;
> +}
> +
> +static const struct v4l2_async_notifier_operations v4l2_common_notifier_ops = {
> + .bound = v4l2_common_notifier_bound,
> +};
> +
> +/*
> + * The only one endpoint under one port. And all ports number is continues.
> + */
> +static int
> +v4l2_async_nf_parse_fwnode(struct device *dev, struct media_pad *pads, u32 pads_count,
> + struct v4l2_async_notifier *notifier)
> +{
> + struct v4l2_subdev *sd = notifier->sd;
> + struct v4l2_async_connection *asd;
> + struct v4l2_fwnode_endpoint vep;
> + struct media_pad *pad;
> + int ret;
> +
> + if (!sd->internal_ops || !sd->internal_ops->set_pad_by_ep)
> + return dev_err_probe(dev, -EINVAL,
> + "Missed set_pad_by_ep() callback\n");
> + pad = pads;
> +
> + fwnode_graph_for_each_endpoint_scoped(dev_fwnode(dev), ep) {
> + u32 flags;
> +
> + ret = v4l2_fwnode_endpoint_parse(ep, &vep);
> + if (ret)
> + return dev_err_probe(dev, ret, "failed to parse endpoint\n");
> +
> + if (vep.base.port >= pads_count)
> + return dev_err_probe(dev, -EINVAL,
> + "port number bigger than pad number\n");
> +
> + pad = pads + vep.base.port;
> +
> + ret = sd->internal_ops->set_pad_by_ep(sd, pad, &vep);
> + if (ret < 0)
> + return dev_err_probe(dev, ret, "Can support endpoint\n");
> +
> + flags = pad->flags;
> +
> + if (flags & MEDIA_PAD_FL_SOURCE)
> + continue; /* Bypass source port */
> +
> + notifier->ops = &v4l2_common_notifier_ops;
> +
> + asd = v4l2_async_nf_add_fwnode_remote(notifier, ep,
> + struct v4l2_async_connection);
> + if (IS_ERR(asd))
> + return dev_err_probe(dev, PTR_ERR(asd),
> + "failed to add notifier\n");
> + }
> +
> + return 0;
> +}
> +
> +void media_async_subdev_cleanup(struct v4l2_subdev *sd)
> +{
> + v4l2_async_unregister_subdev(sd);
> + v4l2_subdev_cleanup(sd);
> + media_entity_cleanup(&sd->entity);
> + v4l2_async_nf_unregister(sd->subdev_notifier);
> + v4l2_async_nf_cleanup(sd->subdev_notifier);
> + kfree(sd->entity.pads);
> +}
> +EXPORT_SYMBOL_GPL(media_async_subdev_cleanup);
> +
> +int __media_async_register_subdev(struct v4l2_subdev *sd, struct module *module)
> +{
> + struct device *dev = sd->dev;
> + u32 ep_count;
> + int ret;
> +
> + if (WARN_ON(!sd->dev))
> + return -ENODEV;
> +
> + struct v4l2_async_notifier *notifier __free(kfree) = kzalloc_obj(*notifier);
> + if (!notifier)
> + return -ENOMEM;
> +
> + v4l2_async_subdev_nf_init(notifier, sd);
> +
> + ep_count = fwnode_graph_get_endpoint_count(dev_fwnode(dev),
> + FWNODE_GRAPH_DEVICE_DISABLED);
> + if (!ep_count)
> + return dev_err_probe(dev, -EINVAL, "No connected endpoints\n");
> +
> + struct media_pad *pads __free(kfree) = kzalloc_objs(struct media_pad, ep_count);
> + if (!pads)
> + return -ENOMEM;
> +
> + ret = v4l2_async_nf_parse_fwnode(dev, pads, ep_count, notifier);
> + if (ret < 0)
> + goto out_cleanup;
> +
> + ret = media_entity_pads_init(&sd->entity, ep_count, pads);
> + if (ret)
> + goto out_cleanup;
> +
> + ret = v4l2_async_nf_register(notifier);
> + if (ret < 0)
> + goto out_cleanup;
> +
> + ret = v4l2_subdev_init_finalize(sd);
> + if (ret)
> + goto out_unregister;
> +
> + ret = __v4l2_async_register_subdev(sd, module);
> + if (ret < 0)
> + goto out_unregister;
> +
> + sd->subdev_notifier = no_free_ptr(notifier);
> + retain_and_null_ptr(pads);
> +
> + return 0;
> +
> +out_unregister:
> + v4l2_async_nf_unregister(notifier);
> + v4l2_subdev_cleanup(sd);
> +out_cleanup:
> + v4l2_async_nf_cleanup(notifier);
> +
> + return ret;
> +}
> +EXPORT_SYMBOL_GPL(__media_async_register_subdev);
> +
> MODULE_DESCRIPTION("V4L2 fwnode binding parsing library");
> MODULE_LICENSE("GPL");
> MODULE_AUTHOR("Sakari Ailus <sakari.ailus@linux.intel.com>");
> diff --git a/include/media/v4l2-async.h b/include/media/v4l2-async.h
> index 54a2d9620ed5b..ca41820f776c5 100644
> --- a/include/media/v4l2-async.h
> +++ b/include/media/v4l2-async.h
> @@ -345,4 +345,43 @@ __v4l2_async_register_subdev_sensor(struct v4l2_subdev *sd, struct module *modul
> * @sd: pointer to &struct v4l2_subdev
> */
> void v4l2_async_unregister_subdev(struct v4l2_subdev *sd);
> +
> +enum v4l2_subdev_1to1_pads {
> + V4L2_SUBDEV_1TO1_PADS_SINK,
> + V4L2_SUBDEV_1TO1_PADS_SOURCE,
> + V4L2_SUBDEV_1TO1_PADS_TOTAL,
> +};
> +
> +/**
> + * media_async_register_subdev - registers a sub-device to the asynchronous
> + * sub-device framework and parse set up common
> + * related devices
> + *
> + * @sd: pointer to struct &v4l2_subdev
> + *
> + * Register a V4L2 sub-device with the asynchronous sub-device framework.
> + * In addition to v4l2_async_register_subdev(), this function parses the
> + * firmware graph, creates media pads for the endpoints, and registers common
> + * notifiers to create media links between connected devices.
> + *
> + * This function also init media_pads.
> + *
> + * The sub-device is unregistered and cleanup by media_async_subdev_cleanup()
> + *
> + * While registered, the subdev module is marked as in-use.
> + *
> + * An error is returned if the module is no longer loaded on any attempts
> + * to register it.
> + */
> +#define media_async_register_subdev(sd_1to1) \
> + __media_async_register_subdev(sd_1to1, THIS_MODULE)
> +
> +int __media_async_register_subdev(struct v4l2_subdev *sd_1to1, struct module *module);
> +
> +/**
> + * media_async_subdev_cleanup - unregistered and cleanup subdev and media pads
> + * @sd_1to1: pointer to struct &v4l2_subdev_1to1
> + */
> +void media_async_subdev_cleanup(struct v4l2_subdev *sd_1to1);
> +
> #endif
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 13+ messages in thread* Re: [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper
2026-07-02 16:15 ` Laurent Pinchart
@ 2026-07-02 18:11 ` Frank Li
2026-07-02 18:19 ` Laurent Pinchart
0 siblings, 1 reply; 13+ messages in thread
From: Frank Li @ 2026-07-02 18:11 UTC (permalink / raw)
To: Laurent Pinchart
Cc: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch, Frank Li,
Martin Kepplinger-Novakovic, Rui Miguel Silva, Purism Kernel Team,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, linux-media, linux-kernel,
imx, Guoniu Zhou, devicetree, linux-arm-kernel
On Thu, Jul 02, 2026 at 07:15:19PM +0300, Laurent Pinchart wrote:
> Hi Frank,
>
> Have you missed the comment in v6 ?
>
> https://lore.kernel.org/all/20260629084654.GB3054459@killaraus.ideasonboard.com/
Sorry, I forget emphased it in change log.
"For the reason stated by Sakari in patch 1/9 (dependency from MC to
V4L2), I don't think a "media_async_register_subdev()" function is a
good idea."
The reason already NOT existed in v7, I removed v4l2_fwnode_endpoint from
media_pad. So MC will not depdent to V4L2.
So this comments is not suit for this version.
Frank
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper
2026-07-02 18:11 ` Frank Li
@ 2026-07-02 18:19 ` Laurent Pinchart
2026-07-02 18:59 ` Frank Li
0 siblings, 1 reply; 13+ messages in thread
From: Laurent Pinchart @ 2026-07-02 18:19 UTC (permalink / raw)
To: Frank Li
Cc: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch, Frank Li,
Martin Kepplinger-Novakovic, Rui Miguel Silva, Purism Kernel Team,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, linux-media, linux-kernel,
imx, Guoniu Zhou, devicetree, linux-arm-kernel
On Thu, Jul 02, 2026 at 01:11:03PM -0500, Frank Li wrote:
> On Thu, Jul 02, 2026 at 07:15:19PM +0300, Laurent Pinchart wrote:
> > Hi Frank,
> >
> > Have you missed the comment in v6 ?
> >
> > https://lore.kernel.org/all/20260629084654.GB3054459@killaraus.ideasonboard.com/
>
> Sorry, I forget emphased it in change log.
>
> "For the reason stated by Sakari in patch 1/9 (dependency from MC to
> V4L2), I don't think a "media_async_register_subdev()" function is a
> good idea."
>
> The reason already NOT existed in v7, I removed v4l2_fwnode_endpoint from
> media_pad. So MC will not depdent to V4L2.
>
> So this comments is not suit for this version.
media_async_register_subdev(), with its "media_" prefix, appears part of
the MC API, but it operates on a subdev. At least the function name
should be changed in my opinion.
--
Regards,
Laurent Pinchart
^ permalink raw reply [flat|nested] 13+ messages in thread
* Re: [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper
2026-07-02 18:19 ` Laurent Pinchart
@ 2026-07-02 18:59 ` Frank Li
0 siblings, 0 replies; 13+ messages in thread
From: Frank Li @ 2026-07-02 18:59 UTC (permalink / raw)
To: Laurent Pinchart
Cc: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch, Frank Li,
Martin Kepplinger-Novakovic, Rui Miguel Silva, Purism Kernel Team,
Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam, linux-media, linux-kernel,
imx, Guoniu Zhou, devicetree, linux-arm-kernel
On Thu, Jul 02, 2026 at 09:19:20PM +0300, Laurent Pinchart wrote:
> On Thu, Jul 02, 2026 at 01:11:03PM -0500, Frank Li wrote:
> > On Thu, Jul 02, 2026 at 07:15:19PM +0300, Laurent Pinchart wrote:
> > > Hi Frank,
> > >
> > > Have you missed the comment in v6 ?
> > >
> > > https://lore.kernel.org/all/20260629084654.GB3054459@killaraus.ideasonboard.com/
> >
> > Sorry, I forget emphased it in change log.
> >
> > "For the reason stated by Sakari in patch 1/9 (dependency from MC to
> > V4L2), I don't think a "media_async_register_subdev()" function is a
> > good idea."
> >
> > The reason already NOT existed in v7, I removed v4l2_fwnode_endpoint from
> > media_pad. So MC will not depdent to V4L2.
> >
> > So this comments is not suit for this version.
>
> media_async_register_subdev(), with its "media_" prefix, appears part of
> the MC API, but it operates on a subdev. At least the function name
> should be changed in my opinion.
Name is easy to fix. The key is if the overall direction and method is
good enough to go futher.
Optional naming here
v4l2_async_register_subdev_with_created_pad()
v4l2_create_pad_and_async_register_subdev()
v4l2_async_register_subdev_from_fw_ports()
...
Frank
>
> --
> Regards,
>
> Laurent Pinchart
^ permalink raw reply [flat|nested] 13+ messages in thread
* [PATCH v7 3/8] media: synopsys: Use v4l2_subdev_get_frame_desc_passthrough()
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
2026-07-02 16:03 ` [PATCH v7 1/8] media: subdev: Add set_pad_by_ep() callback to internal ops Frank.Li
2026-07-02 16:03 ` [PATCH v7 2/8] media: subdev: Add media_async_register_subdev() helper Frank.Li
@ 2026-07-02 16:03 ` Frank.Li
2026-07-02 16:04 ` [PATCH v7 4/8] media: synopsys: Use media_async_register_subdev() to simplify code Frank.Li
` (4 subsequent siblings)
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:03 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel
From: Frank Li <Frank.Li@nxp.com>
Replace the local frame descriptor callback implementation with
v4l2_subdev_get_frame_desc_passthrough().
This helper provides the same functionality while avoiding duplicate
code and simplifying the driver implementation.
Reviewed-by: Guoniu Zhou <guoniu.zhou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
chnage in v7
- none
change in v6
- collect gouniu's review by
change in v5
- new patch
---
drivers/media/platform/synopsys/dw-mipi-csi2rx.c | 22 +---------------------
1 file changed, 1 insertion(+), 21 deletions(-)
diff --git a/drivers/media/platform/synopsys/dw-mipi-csi2rx.c b/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
index 41e48365167e5..f51367409ff46 100644
--- a/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
+++ b/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
@@ -630,31 +630,11 @@ static int dw_mipi_csi2rx_disable_streams(struct v4l2_subdev *sd,
return ret;
}
-static int
-dw_mipi_csi2rx_get_frame_desc(struct v4l2_subdev *sd, unsigned int pad,
- struct v4l2_mbus_frame_desc *fd)
-{
- struct dw_mipi_csi2rx_device *csi2 = to_csi2(sd);
- struct v4l2_subdev *remote_sd;
- struct media_pad *remote_pad;
-
- remote_pad = media_pad_remote_pad_unique(&csi2->pads[DW_MIPI_CSI2RX_PAD_SINK]);
- if (IS_ERR(remote_pad)) {
- dev_err(csi2->dev, "can't get remote source pad\n");
- return PTR_ERR(remote_pad);
- }
-
- remote_sd = media_entity_to_v4l2_subdev(remote_pad->entity);
-
- return v4l2_subdev_call(remote_sd, pad, get_frame_desc,
- remote_pad->index, fd);
-}
-
static const struct v4l2_subdev_pad_ops dw_mipi_csi2rx_pad_ops = {
.enum_mbus_code = dw_mipi_csi2rx_enum_mbus_code,
.get_fmt = v4l2_subdev_get_fmt,
.set_fmt = dw_mipi_csi2rx_set_fmt,
- .get_frame_desc = dw_mipi_csi2rx_get_frame_desc,
+ .get_frame_desc = v4l2_subdev_get_frame_desc_passthrough,
.set_routing = dw_mipi_csi2rx_set_routing,
.enable_streams = dw_mipi_csi2rx_enable_streams,
.disable_streams = dw_mipi_csi2rx_disable_streams,
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v7 4/8] media: synopsys: Use media_async_register_subdev() to simplify code
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
` (2 preceding siblings ...)
2026-07-02 16:03 ` [PATCH v7 3/8] media: synopsys: Use v4l2_subdev_get_frame_desc_passthrough() Frank.Li
@ 2026-07-02 16:04 ` Frank.Li
2026-07-02 16:04 ` [PATCH v7 5/8] dt-bindings: media: add i.MX parallel CPI support Frank.Li
` (3 subsequent siblings)
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:04 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel
From: Frank Li <Frank.Li@nxp.com>
Use the media_async_register_subdev() to simplify the driver.
Replace the local subdev registration and media pad setup code with
media_async_register_subdev(). Reduce boilerplate code and aligns the
driver with the common pattern used by simple subdevices that each media
pad has one endpoint in fwnode.
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
chagne in v7
- keep bus_type in csi2 struture
- update set_pad_by_ep() argurment.
change in v6
- use media_async_register_subdev()
- remove sd_1to1.
change in v5
new patch
previous method:
https://lore.kernel.org/imx/20260226-v4l2_init_register-v2-2-902d7140f9fa@nxp.com/
---
drivers/media/platform/synopsys/dw-mipi-csi2rx.c | 172 +++++------------------
1 file changed, 39 insertions(+), 133 deletions(-)
diff --git a/drivers/media/platform/synopsys/dw-mipi-csi2rx.c b/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
index f51367409ff46..0d8834e77a08a 100644
--- a/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
+++ b/drivers/media/platform/synopsys/dw-mipi-csi2rx.c
@@ -78,12 +78,6 @@ enum dw_mipi_csi2rx_regs_index {
DW_MIPI_CSI2RX_MAX,
};
-enum {
- DW_MIPI_CSI2RX_PAD_SINK,
- DW_MIPI_CSI2RX_PAD_SRC,
- DW_MIPI_CSI2RX_PAD_MAX,
-};
-
struct dw_mipi_csi2rx_device;
struct dw_mipi_csi2rx_drvdata {
@@ -112,8 +106,6 @@ struct dw_mipi_csi2rx_device {
const struct dw_mipi_csi2rx_format *formats;
unsigned int formats_num;
- struct media_pad pads[DW_MIPI_CSI2RX_PAD_MAX];
- struct v4l2_async_notifier notifier;
struct v4l2_subdev sd;
enum v4l2_mbus_type bus_type;
@@ -360,9 +352,10 @@ dw_mipi_csi2rx_find_format(struct dw_mipi_csi2rx_device *csi2, u32 mbus_code)
static int dw_mipi_csi2rx_start(struct dw_mipi_csi2rx_device *csi2)
{
+ struct media_pad *sink_pad = &csi2->sd.entity.pads[V4L2_SUBDEV_1TO1_PADS_SINK];
+ u32 lanes = csi2->lanes_num;
struct media_pad *source_pad;
union phy_configure_opts opts;
- u32 lanes = csi2->lanes_num;
u32 control = 0;
s64 link_freq;
int ret;
@@ -370,8 +363,7 @@ static int dw_mipi_csi2rx_start(struct dw_mipi_csi2rx_device *csi2)
if (lanes < 1 || lanes > 4)
return -EINVAL;
- source_pad = media_pad_remote_pad_unique(
- &csi2->pads[DW_MIPI_CSI2RX_PAD_SINK]);
+ source_pad = media_pad_remote_pad_unique(sink_pad);
if (IS_ERR(source_pad))
return PTR_ERR(source_pad);
@@ -458,16 +450,16 @@ dw_mipi_csi2rx_enum_mbus_code(struct v4l2_subdev *sd,
struct dw_mipi_csi2rx_device *csi2 = to_csi2(sd);
switch (code->pad) {
- case DW_MIPI_CSI2RX_PAD_SRC:
+ case V4L2_SUBDEV_1TO1_PADS_SOURCE:
if (code->index)
return -EINVAL;
code->code =
v4l2_subdev_state_get_format(sd_state,
- DW_MIPI_CSI2RX_PAD_SINK)->code;
+ V4L2_SUBDEV_1TO1_PADS_SINK)->code;
return 0;
- case DW_MIPI_CSI2RX_PAD_SINK:
+ case V4L2_SUBDEV_1TO1_PADS_SINK:
if (code->index >= csi2->formats_num)
return -EINVAL;
@@ -487,7 +479,7 @@ static int dw_mipi_csi2rx_set_fmt(struct v4l2_subdev *sd,
struct v4l2_mbus_framefmt *sink, *src;
/* the format on the source pad always matches the sink pad */
- if (format->pad == DW_MIPI_CSI2RX_PAD_SRC)
+ if (format->pad == V4L2_SUBDEV_1TO1_PADS_SOURCE)
return v4l2_subdev_get_fmt(sd, state, format);
sink = v4l2_subdev_state_get_format(state, format->pad, format->stream);
@@ -549,12 +541,12 @@ static int dw_mipi_csi2rx_enable_streams(struct v4l2_subdev *sd,
u64 mask;
int ret;
- sink_pad = &sd->entity.pads[DW_MIPI_CSI2RX_PAD_SINK];
+ sink_pad = &sd->entity.pads[V4L2_SUBDEV_1TO1_PADS_SINK];
remote_pad = media_pad_remote_pad_first(sink_pad);
remote_sd = media_entity_to_v4l2_subdev(remote_pad->entity);
- mask = v4l2_subdev_state_xlate_streams(state, DW_MIPI_CSI2RX_PAD_SINK,
- DW_MIPI_CSI2RX_PAD_SRC,
+ mask = v4l2_subdev_state_xlate_streams(state, V4L2_SUBDEV_1TO1_PADS_SINK,
+ V4L2_SUBDEV_1TO1_PADS_SOURCE,
&streams_mask);
if (!csi2->enabled_streams) {
@@ -608,12 +600,12 @@ static int dw_mipi_csi2rx_disable_streams(struct v4l2_subdev *sd,
u64 mask;
int ret;
- sink_pad = &sd->entity.pads[DW_MIPI_CSI2RX_PAD_SINK];
+ sink_pad = &sd->entity.pads[V4L2_SUBDEV_1TO1_PADS_SINK];
remote_pad = media_pad_remote_pad_first(sink_pad);
remote_sd = media_entity_to_v4l2_subdev(remote_pad->entity);
- mask = v4l2_subdev_state_xlate_streams(state, DW_MIPI_CSI2RX_PAD_SINK,
- DW_MIPI_CSI2RX_PAD_SRC,
+ mask = v4l2_subdev_state_xlate_streams(state, V4L2_SUBDEV_1TO1_PADS_SINK,
+ V4L2_SUBDEV_1TO1_PADS_SOURCE,
&streams_mask);
ret = v4l2_subdev_disable_streams(remote_sd, remote_pad->index, mask);
@@ -649,9 +641,9 @@ static int dw_mipi_csi2rx_init_state(struct v4l2_subdev *sd,
{
struct v4l2_subdev_route routes[] = {
{
- .sink_pad = DW_MIPI_CSI2RX_PAD_SINK,
+ .sink_pad = V4L2_SUBDEV_1TO1_PADS_SINK,
.sink_stream = 0,
- .source_pad = DW_MIPI_CSI2RX_PAD_SRC,
+ .source_pad = V4L2_SUBDEV_1TO1_PADS_SOURCE,
.source_stream = 0,
.flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE,
},
@@ -666,95 +658,42 @@ static int dw_mipi_csi2rx_init_state(struct v4l2_subdev *sd,
&default_format);
}
-static const struct v4l2_subdev_internal_ops dw_mipi_csi2rx_internal_ops = {
- .init_state = dw_mipi_csi2rx_init_state,
-};
-
-static int dw_mipi_csi2rx_notifier_bound(struct v4l2_async_notifier *notifier,
- struct v4l2_subdev *sd,
- struct v4l2_async_connection *asd)
+static int dw_mipi_set_pad_by_ep(struct v4l2_subdev *sd, struct media_pad *pad,
+ struct v4l2_fwnode_endpoint *vep)
{
- struct dw_mipi_csi2rx_device *csi2 =
- container_of(notifier, struct dw_mipi_csi2rx_device, notifier);
- struct media_pad *sink_pad = &csi2->pads[DW_MIPI_CSI2RX_PAD_SINK];
- int ret;
-
- ret = v4l2_create_fwnode_links_to_pad(sd, sink_pad,
- MEDIA_LNK_FL_ENABLED);
- if (ret) {
- dev_err(csi2->dev, "failed to link source pad of %s\n",
- sd->name);
- return ret;
- }
-
- return 0;
-}
-
-static const struct v4l2_async_notifier_operations dw_mipi_csi2rx_notifier_ops = {
- .bound = dw_mipi_csi2rx_notifier_bound,
-};
-
-static int dw_mipi_csi2rx_register_notifier(struct dw_mipi_csi2rx_device *csi2)
-{
- struct v4l2_async_connection *asd;
- struct v4l2_async_notifier *ntf = &csi2->notifier;
- struct v4l2_fwnode_endpoint vep;
- struct v4l2_subdev *sd = &csi2->sd;
- struct device *dev = csi2->dev;
- int ret;
-
- struct fwnode_handle *ep __free(fwnode_handle) =
- fwnode_graph_get_endpoint_by_id(dev_fwnode(dev), 0, 0, 0);
- if (!ep)
- return dev_err_probe(dev, -ENODEV, "failed to get endpoint\n");
-
- vep.bus_type = V4L2_MBUS_UNKNOWN;
- ret = v4l2_fwnode_endpoint_parse(ep, &vep);
- if (ret)
- return dev_err_probe(dev, ret, "failed to parse endpoint\n");
+ if (vep->base.port == V4L2_SUBDEV_1TO1_PADS_SINK) {
+ if (vep->bus_type != V4L2_MBUS_CSI2_DPHY &&
+ vep->bus_type != V4L2_MBUS_CSI2_CPHY)
+ return -EINVAL;
- if (vep.bus_type != V4L2_MBUS_CSI2_DPHY &&
- vep.bus_type != V4L2_MBUS_CSI2_CPHY)
- return dev_err_probe(dev, -EINVAL,
- "invalid bus type of endpoint\n");
+ struct dw_mipi_csi2rx_device *csi2 = to_csi2(sd);
- csi2->bus_type = vep.bus_type;
- csi2->lanes_num = vep.bus.mipi_csi2.num_data_lanes;
+ pad->flags = MEDIA_PAD_FL_SINK | MEDIA_PAD_FL_MUST_CONNECT;
- v4l2_async_subdev_nf_init(ntf, sd);
- ntf->ops = &dw_mipi_csi2rx_notifier_ops;
+ csi2->bus_type = vep->bus_type;
+ csi2->lanes_num = vep->bus.mipi_csi2.num_data_lanes;
- asd = v4l2_async_nf_add_fwnode_remote(ntf, ep,
- struct v4l2_async_connection);
- if (IS_ERR(asd)) {
- ret = PTR_ERR(asd);
- goto err_nf_cleanup;
+ return 0;
}
- ret = v4l2_async_nf_register(ntf);
- if (ret) {
- ret = dev_err_probe(dev, ret, "failed to register notifier\n");
- goto err_nf_cleanup;
+ if (vep->base.port == V4L2_SUBDEV_1TO1_PADS_SOURCE) {
+ pad->flags = MEDIA_PAD_FL_SOURCE | MEDIA_PAD_FL_MUST_CONNECT;
+ return 0;
}
- return 0;
-
-err_nf_cleanup:
- v4l2_async_nf_cleanup(ntf);
-
- return ret;
+ return -EINVAL;
}
+static const struct v4l2_subdev_internal_ops dw_mipi_csi2rx_internal_ops = {
+ .init_state = dw_mipi_csi2rx_init_state,
+ .set_pad_by_ep = dw_mipi_set_pad_by_ep,
+};
+
static int dw_mipi_csi2rx_register(struct dw_mipi_csi2rx_device *csi2)
{
- struct media_pad *pads = csi2->pads;
struct v4l2_subdev *sd = &csi2->sd;
int ret;
- ret = dw_mipi_csi2rx_register_notifier(csi2);
- if (ret)
- goto err;
-
v4l2_subdev_init(sd, &dw_mipi_csi2rx_ops);
sd->dev = csi2->dev;
sd->entity.ops = &dw_mipi_csi2rx_media_ops;
@@ -764,45 +703,12 @@ static int dw_mipi_csi2rx_register(struct dw_mipi_csi2rx_device *csi2)
snprintf(sd->name, sizeof(sd->name), "dw-mipi-csi2rx %s",
dev_name(csi2->dev));
- pads[DW_MIPI_CSI2RX_PAD_SINK].flags = MEDIA_PAD_FL_SINK |
- MEDIA_PAD_FL_MUST_CONNECT;
- pads[DW_MIPI_CSI2RX_PAD_SRC].flags = MEDIA_PAD_FL_SOURCE;
- ret = media_entity_pads_init(&sd->entity, DW_MIPI_CSI2RX_PAD_MAX, pads);
+ ret = media_async_register_subdev(&csi2->sd);
if (ret)
- goto err_notifier_unregister;
-
- ret = v4l2_subdev_init_finalize(sd);
- if (ret)
- goto err_entity_cleanup;
-
- ret = v4l2_async_register_subdev(sd);
- if (ret) {
- dev_err(sd->dev, "failed to register CSI-2 subdev\n");
- goto err_subdev_cleanup;
- }
+ return dev_err_probe(sd->dev, ret,
+ "failed to register CSI-2 subdev\n");
return 0;
-
-err_subdev_cleanup:
- v4l2_subdev_cleanup(sd);
-err_entity_cleanup:
- media_entity_cleanup(&sd->entity);
-err_notifier_unregister:
- v4l2_async_nf_unregister(&csi2->notifier);
- v4l2_async_nf_cleanup(&csi2->notifier);
-err:
- return ret;
-}
-
-static void dw_mipi_csi2rx_unregister(struct dw_mipi_csi2rx_device *csi2)
-{
- struct v4l2_subdev *sd = &csi2->sd;
-
- v4l2_async_unregister_subdev(sd);
- v4l2_subdev_cleanup(sd);
- media_entity_cleanup(&sd->entity);
- v4l2_async_nf_unregister(&csi2->notifier);
- v4l2_async_nf_cleanup(&csi2->notifier);
}
static void imx93_csi2rx_dphy_assert_reset(struct dw_mipi_csi2rx_device *csi2)
@@ -993,7 +899,7 @@ static void dw_mipi_csi2rx_remove(struct platform_device *pdev)
{
struct dw_mipi_csi2rx_device *csi2 = platform_get_drvdata(pdev);
- dw_mipi_csi2rx_unregister(csi2);
+ media_async_subdev_cleanup(&csi2->sd);
phy_exit(csi2->phy);
}
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v7 5/8] dt-bindings: media: add i.MX parallel CPI support
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
` (3 preceding siblings ...)
2026-07-02 16:04 ` [PATCH v7 4/8] media: synopsys: Use media_async_register_subdev() to simplify code Frank.Li
@ 2026-07-02 16:04 ` Frank.Li
2026-07-02 16:04 ` [PATCH v7 6/8] media: nxp: add V4L2 subdev driver for camera parallel interface (CPI) Frank.Li
` (2 subsequent siblings)
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:04 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel, Alice Yuan, Krzysztof Kozlowski
From: Alice Yuan <alice.yuan@nxp.com>
Document the binding for parallel CPI controller found in i.MX8QXP, i.MX93
and i.MX91 SoCs.
Signed-off-by: Alice Yuan <alice.yuan@nxp.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Chaanges from v5 -v6
- none
Chagnes in v4
- add Laurent Pinchart's review by tag
- fix $ref: /schemas/graph.yaml#/$defs/port-base, original is
$ref: /schemas/graph.yaml#/properties/port-base
Change in v3:
- use enum at compatible string
- add ref to video-interfaces.yaml#
- use cpi as node name in examples.
- replace csi (Camera Serial Interface) with CPI (Camera Parallel Interface)
in commit message.
Change in v2:
- use pcif surfix as Laurent Pinchart's suggest.
- put power-domains into required list
---
.../devicetree/bindings/media/fsl,imx93-pcif.yaml | 126 +++++++++++++++++++++
MAINTAINERS | 1 +
2 files changed, 127 insertions(+)
diff --git a/Documentation/devicetree/bindings/media/fsl,imx93-pcif.yaml b/Documentation/devicetree/bindings/media/fsl,imx93-pcif.yaml
new file mode 100644
index 0000000000000..9dd0331f6ef75
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/fsl,imx93-pcif.yaml
@@ -0,0 +1,126 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/media/fsl,imx93-pcif.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: i.MX8/9 Parallel Camera Interface
+
+maintainers:
+ - Frank Li <Frank.Li@nxp.com>
+
+description: |
+ This is device node for the Parallel Camera Interface which enables the
+ chip to connect directly to external Parallel CMOS image sensors.
+ Supports up to 80MHz input clock from sensor.
+ Supports the following input data formats
+ - 8-bit/10-bit Camera Sensor Interface (CSI)
+ - 8-bit data port for RGB, YCbCr, and YUV data input
+ - 8-bit/10-bit data ports for Bayer data input
+ Parallel Camera Interface is hooked to the Imaging subsystem via the
+ Pixel Link.
+
+properties:
+ compatible:
+ oneOf:
+ - enum:
+ - fsl,imx8qxp-pcif
+ - fsl,imx93-pcif
+ - items:
+ - enum:
+ - fsl,imx91-pcif
+ - const: fsl,imx93-pcif
+
+ reg:
+ maxItems: 1
+
+ clocks:
+ maxItems: 2
+
+ clock-names:
+ items:
+ - const: pixel
+ - const: ipg
+
+ power-domains:
+ maxItems: 1
+
+ ports:
+ $ref: /schemas/graph.yaml#/properties/ports
+
+ properties:
+ port@0:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: Input port node.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ bus-type:
+ const: 5
+
+ port@1:
+ $ref: /schemas/graph.yaml#/$defs/port-base
+ unevaluatedProperties: false
+ description: Output port node.
+
+ properties:
+ endpoint:
+ $ref: video-interfaces.yaml#
+ unevaluatedProperties: false
+
+ properties:
+ bus-type:
+ const: 5
+
+required:
+ - compatible
+ - reg
+ - clocks
+ - clock-names
+ - power-domains
+ - ports
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/clock/imx93-clock.h>
+ #include <dt-bindings/power/fsl,imx93-power.h>
+
+ cpi@4ac10070 {
+ compatible = "fsl,imx93-pcif";
+ reg = <0x4ac10070 0x10>;
+ clocks = <&clk IMX93_CLK_MIPI_CSI_GATE>,
+ <&clk IMX93_CLK_MEDIA_APB>;
+ clock-names = "pixel", "ipg";
+ assigned-clocks = <&clk IMX93_CLK_CAM_PIX>;
+ assigned-clock-parents = <&clk IMX93_CLK_VIDEO_PLL>;
+ assigned-clock-rates = <140000000>;
+ power-domains = <&media_blk_ctrl IMX93_MEDIABLK_PD_MIPI_CSI>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ endpoint {
+ remote-endpoint = <&mt9m114_ep>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ endpoint {
+ remote-endpoint = <&isi_in>;
+ };
+ };
+ };
+ };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 31188163a8592..f690826964369 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16246,6 +16246,7 @@ L: linux-media@vger.kernel.org
S: Maintained
T: git git://linuxtv.org/media.git
F: Documentation/admin-guide/media/imx7.rst
+F: Documentation/devicetree/bindings/media/fsl,imx93-pcif.yaml
F: Documentation/devicetree/bindings/media/nxp,imx-mipi-csi2.yaml
F: Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
F: Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v7 6/8] media: nxp: add V4L2 subdev driver for camera parallel interface (CPI)
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
` (4 preceding siblings ...)
2026-07-02 16:04 ` [PATCH v7 5/8] dt-bindings: media: add i.MX parallel CPI support Frank.Li
@ 2026-07-02 16:04 ` Frank.Li
2026-07-02 16:04 ` [PATCH v7 7/8] arm64: dts: imx8: add camera parallel interface (CPI) node Frank.Li
2026-07-02 16:04 ` [PATCH v7 8/8] arm64: dts: imx8qxp-mek: add parallel ov5640 camera support Frank.Li
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:04 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel, Alice Yuan, Robert Chiras, Zhipeng Wang
From: Alice Yuan <alice.yuan@nxp.com>
Add a V4L2 sub-device driver for the CPI controller found on i.MX8QXP,
i.MX8QM, and i.MX93 SoCs. This controller supports parallel camera sensors
and enables image data capture through a parallel interface.
Signed-off-by: Alice Yuan <alice.yuan@nxp.com>
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Zhipeng Wang <zhipeng.wang_1@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Change in v7
- save vep flags to local driver data
- update according new API change.
Change in v6
- Don't use subdev_1to1
- use new api media_async_register_subdev()
- remove used switch -case
Change in v5
- Use subdev_1to1 register function
- Use v4l2_subdev_get_frame_desc_passthrough
- Use dwc csi2 similar logic enable/disable stream
- Add route settup at imx_cpi_init_state()
- Remove V2 register layout support, add it later
change in v4
- remove unnecesary header file.
- use devm_bulk_clk_get().
- update kConfig i.MX8/i.MX9
- Remove define IMX_CPI_DEF_PIX_WIDTH ..., which used once only
- drop get_interface_ctrl_reg1_param
- drop uv-swap
- drop imx_cpi_link_setup by use immutable link.
- use enable/disable_stream() replace depericated .s_stream.
- remove dbg print and reg dump functions.
- use goto/.remove() to do manual cleanup.
- remove imx93 support. Add it later.
change in v3
- replace csi with cpi
- use __free(fwnode_handle) to simpilfy code
- remove imx91 driver data, which is the same as imx93
change in v2
- remove MODULE_ALIAS
- use devm_pm_runtime_enable() and cleanup remove function
- change output format to 1x16. controller convert 2x8 to 1x16 format
---
MAINTAINERS | 1 +
drivers/media/platform/nxp/Kconfig | 12 +
drivers/media/platform/nxp/Makefile | 1 +
drivers/media/platform/nxp/imx-parallel-cpi.c | 629 ++++++++++++++++++++++++++
4 files changed, 643 insertions(+)
diff --git a/MAINTAINERS b/MAINTAINERS
index f690826964369..22f60b6e89bf2 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -16251,6 +16251,7 @@ F: Documentation/devicetree/bindings/media/nxp,imx-mipi-csi2.yaml
F: Documentation/devicetree/bindings/media/nxp,imx7-csi.yaml
F: Documentation/devicetree/bindings/media/nxp,imx8mq-mipi-csi2.yaml
F: drivers/media/platform/nxp/imx-mipi-csis.c
+F: drivers/media/platform/nxp/imx-parallel-cpi.c
F: drivers/media/platform/nxp/imx7-media-csi.c
F: drivers/media/platform/nxp/imx8mq-mipi-csi2.c
diff --git a/drivers/media/platform/nxp/Kconfig b/drivers/media/platform/nxp/Kconfig
index 40e3436669e21..90f7c792003f2 100644
--- a/drivers/media/platform/nxp/Kconfig
+++ b/drivers/media/platform/nxp/Kconfig
@@ -39,6 +39,18 @@ config VIDEO_IMX_MIPI_CSIS
Video4Linux2 sub-device driver for the MIPI CSI-2 CSIS receiver
v3.3/v3.6.3 found on some i.MX7 and i.MX8 SoCs.
+config VIDEO_IMX_PARALLEL_CPI
+ tristate "NXP i.MX8/i.MX9 Parallel CPI Driver"
+ depends on ARCH_MXC || COMPILE_TEST
+ depends on VIDEO_DEV
+ select MEDIA_CONTROLLER
+ select V4L2_1TO1
+ select V4L2_FWNODE
+ select VIDEO_V4L2_SUBDEV_API
+ help
+ Video4Linux2 sub-device driver for PARALLEL CPI receiver found
+ on some iMX8 and iMX9 SoCs.
+
source "drivers/media/platform/nxp/imx8-isi/Kconfig"
# mem2mem drivers
diff --git a/drivers/media/platform/nxp/Makefile b/drivers/media/platform/nxp/Makefile
index 4d90eb7136525..5346919d2f108 100644
--- a/drivers/media/platform/nxp/Makefile
+++ b/drivers/media/platform/nxp/Makefile
@@ -7,5 +7,6 @@ obj-y += imx8-isi/
obj-$(CONFIG_VIDEO_IMX7_CSI) += imx7-media-csi.o
obj-$(CONFIG_VIDEO_IMX8MQ_MIPI_CSI2) += imx8mq-mipi-csi2.o
obj-$(CONFIG_VIDEO_IMX_MIPI_CSIS) += imx-mipi-csis.o
+obj-$(CONFIG_VIDEO_IMX_PARALLEL_CPI) += imx-parallel-cpi.o
obj-$(CONFIG_VIDEO_IMX_PXP) += imx-pxp.o
obj-$(CONFIG_VIDEO_MX2_EMMAPRP) += mx2_emmaprp.o
diff --git a/drivers/media/platform/nxp/imx-parallel-cpi.c b/drivers/media/platform/nxp/imx-parallel-cpi.c
new file mode 100644
index 0000000000000..735d4a89f7b30
--- /dev/null
+++ b/drivers/media/platform/nxp/imx-parallel-cpi.c
@@ -0,0 +1,629 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * i.MX Parallel CPI receiver driver.
+ *
+ * Copyright 2019-2025 NXP
+ *
+ */
+
+#include <linux/bits.h>
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/limits.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+
+#include <media/v4l2-common.h>
+#include <media/v4l2-device.h>
+#include <media/v4l2-event.h>
+#include <media/v4l2-fwnode.h>
+#include <media/v4l2-mc.h>
+#include <media/v4l2-subdev.h>
+
+/* CI_PI INTERFACE CONTROL */
+#define IF_CTRL_REG_PL_ENABLE BIT(0)
+#define IF_CTRL_REG_PL_VALID BIT(1)
+#define IF_CTRL_REG_DATA_TYPE_SEL BIT(8)
+#define IF_CTRL_REG_DATA_TYPE(x) FIELD_PREP(GENMASK(13, 9), (x))
+
+#define DATA_TYPE_OUT_NULL 0x00
+#define DATA_TYPE_OUT_RGB 0x04
+#define DATA_TYPE_OUT_YUV444 0x08
+#define DATA_TYPE_OUT_YYU420_ODD 0x10
+#define DATA_TYPE_OUT_YYU420_EVEN 0x12
+#define DATA_TYPE_OUT_YYY_ODD 0x18
+#define DATA_TYPE_OUT_UYVY_EVEN 0x1a
+#define DATA_TYPE_OUT_RAW 0x1c
+
+#define IF_CTRL_REG_IF_FORCE_HSYNV_OVERRIDE 0x4
+#define IF_CTRL_REG_IF_FORCE_VSYNV_OVERRIDE 0x2
+#define IF_CTRL_REG_IF_FORCE_DATA_ENABLE_OVERRIDE 0x1
+
+/* CPI INTERFACE CONTROL REG */
+#define CPI_CTRL_REG_CPI_EN BIT(0)
+#define CPI_CTRL_REG_PIXEL_CLK_POL BIT(1)
+#define CPI_CTRL_REG_HSYNC_POL BIT(2)
+#define CPI_CTRL_REG_VSYNC_POL BIT(3)
+#define CPI_CTRL_REG_DE_POL BIT(4)
+#define CPI_CTRL_REG_PIXEL_DATA_POL BIT(5)
+#define CPI_CTRL_REG_CCIR_EXT_VSYNC_EN BIT(6)
+#define CPI_CTRL_REG_CCIR_EN BIT(7)
+#define CPI_CTRL_REG_CCIR_VIDEO_MODE BIT(8)
+#define CPI_CTRL_REG_CCIR_NTSC_EN BIT(9)
+#define CPI_CTRL_REG_CCIR_VSYNC_RESET_EN BIT(10)
+#define CPI_CTRL_REG_CCIR_ECC_ERR_CORRECT_EN BIT(11)
+#define CPI_CTRL_REG_HSYNC_FORCE_EN BIT(12)
+#define CPI_CTRL_REG_VSYNC_FORCE_EN BIT(13)
+#define CPI_CTRL_REG_GCLK_MODE_EN BIT(14)
+#define CPI_CTRL_REG_VALID_SEL BIT(15)
+#define CPI_CTRL_REG_RAW_OUT_SEL BIT(16)
+#define CPI_CTRL_REG_HSYNC_OUT_SEL BIT(17)
+#define CPI_CTRL_REG_HSYNC_PULSE(x) FIELD_PREP(GENMASK(21, 19), (x))
+#define CPI_CTRL_REG_UV_SWAP_EN BIT(22)
+#define CPI_CTRL_REG_DATA_TYPE_IN(x) FIELD_PREP(GENMASK(26, 23), (x))
+#define CPI_CTRL_REG_MASK_VSYNC_COUNTER(x) FIELD_PREP(GENMASK(28, 27), (x))
+#define CPI_CTRL_REG_SOFTRST BIT(31)
+
+/* CPI INTERFACE STATUS */
+#define CPI_STATUS_FIELD_TOGGLE BIT(0)
+#define CPI_STATUS_ECC_ERROR BIT(1)
+
+/* CPI INTERFACE CONTROL REG1 */
+#define CPI_CTRL_REG1_PIXEL_WIDTH(v) FIELD_PREP(GENMASK(15, 0), (v))
+#define CPI_CTRL_REG1_VSYNC_PULSE(v) FIELD_PREP(GENMASK(31, 16), (v))
+
+#define CPI_CTRL_V2_REG1_PIXEL_WIDTH(v) FIELD_PREP(GENMASK(16, 0), (v))
+#define CPI_CTRL_V2_REG1_VSYNC_PULSE(v) FIELD_PREP(GENMASK(31, 16), (v))
+
+/* Need match field DATA_TYPE_IN definition at CPI CTRL register */
+enum cpi_in_data_type {
+ CPI_IN_DT_UYVY_BT656_8 = 0x0,
+ CPI_IN_DT_UYVY_BT656_10,
+ CPI_IN_DT_RGB_8,
+ CPI_IN_DT_BGR_8,
+ CPI_IN_DT_YVYU_8 = 0x5,
+ CPI_IN_DT_YUV_8,
+ CPI_IN_DT_RAW_8 = 0x9,
+ CPI_IN_DT_RAW_10,
+};
+
+enum {
+ PI_GATE_CLOCK_MODE,
+ PI_CCIR_MODE,
+};
+
+enum {
+ PI_V1,
+};
+
+struct imx_cpi_plat_data {
+ u32 version;
+ u32 if_ctrl_reg;
+ u32 interface_status;
+ u32 interface_ctrl_reg;
+ u32 interface_ctrl_reg1;
+};
+
+struct imx_cpi_device {
+ struct device *dev;
+ void __iomem *regs;
+ struct clk_bulk_data *clks;
+ int num_clks;
+
+ struct v4l2_subdev sd;
+
+ const struct imx_cpi_plat_data *pdata;
+
+ u32 flags;
+ u32 enabled_streams;
+ u8 mode;
+};
+
+struct imx_cpi_pix_format {
+ u32 code;
+ u32 output;
+ u32 data_type;
+ u8 width;
+};
+
+static const struct imx_cpi_pix_format imx_cpi_formats[] = {
+ /* YUV formats. */
+ {
+ .code = MEDIA_BUS_FMT_UYVY8_2X8,
+ .output = MEDIA_BUS_FMT_UYVY8_1X16,
+ .data_type = CPI_IN_DT_UYVY_BT656_8,
+ .width = 16,
+ }, {
+ .code = MEDIA_BUS_FMT_YUYV8_2X8,
+ .output = MEDIA_BUS_FMT_YUYV8_1X16,
+ .data_type = CPI_IN_DT_YVYU_8,
+ .width = 16,
+ },
+};
+
+static const struct imx_cpi_plat_data imx8qxp_pdata = {
+ .version = PI_V1,
+ .if_ctrl_reg = 0x0,
+ .interface_status = 0x20,
+ .interface_ctrl_reg = 0x10,
+ .interface_ctrl_reg1 = 0x30,
+};
+
+static const struct imx_cpi_pix_format *find_imx_cpi_format(u32 code)
+{
+ unsigned int i;
+
+ for (i = 0; i < ARRAY_SIZE(imx_cpi_formats); i++)
+ if (code == imx_cpi_formats[i].code)
+ return &imx_cpi_formats[i];
+
+ return NULL;
+}
+
+static void imx_cpi_sw_reset(struct imx_cpi_device *pcpidev)
+{
+ const struct imx_cpi_plat_data *pdata = pcpidev->pdata;
+ u32 val;
+
+ /* Softwaret Reset */
+ val = readl(pcpidev->regs + pdata->interface_ctrl_reg);
+ val |= CPI_CTRL_REG_SOFTRST;
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+
+ fsleep(500);
+ val = readl(pcpidev->regs + pdata->interface_ctrl_reg);
+ val &= ~CPI_CTRL_REG_SOFTRST;
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+}
+
+static void imx_cpi_hw_config(struct imx_cpi_device *pcpidev,
+ const struct imx_cpi_pix_format *pcpidev_fmt)
+{
+ bool hsync_pol = pcpidev->flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH;
+ bool vsync_pol = pcpidev->flags & V4L2_MBUS_VSYNC_ACTIVE_HIGH;
+ const struct imx_cpi_plat_data *pdata = pcpidev->pdata;
+ u32 val;
+
+ /* Software Reset */
+ imx_cpi_sw_reset(pcpidev);
+
+ /* Config PL Data Type */
+ val = IF_CTRL_REG_DATA_TYPE(DATA_TYPE_OUT_YUV444);
+ val |= IF_CTRL_REG_PL_ENABLE | IF_CTRL_REG_PL_VALID;
+ writel(val, pcpidev->regs + pdata->if_ctrl_reg);
+
+ /* Config CTRL REG */
+ val = CPI_CTRL_REG_HSYNC_FORCE_EN | CPI_CTRL_REG_VSYNC_FORCE_EN;
+
+ val |= CPI_CTRL_REG_DATA_TYPE_IN(pcpidev_fmt->data_type) |
+ FIELD_PREP(CPI_CTRL_REG_HSYNC_POL, hsync_pol) |
+ FIELD_PREP(CPI_CTRL_REG_VSYNC_POL, vsync_pol) |
+ FIELD_PREP(CPI_CTRL_REG_PIXEL_CLK_POL, 0) |
+ CPI_CTRL_REG_MASK_VSYNC_COUNTER(3) |
+ CPI_CTRL_REG_HSYNC_PULSE(2);
+
+ if (pcpidev_fmt->code == MEDIA_BUS_FMT_YUYV8_2X8 ||
+ pcpidev_fmt->code == MEDIA_BUS_FMT_UYVY8_2X8)
+ val |= CPI_CTRL_REG_UV_SWAP_EN;
+
+ if (pcpidev->mode == PI_GATE_CLOCK_MODE) {
+ val |= CPI_CTRL_REG_GCLK_MODE_EN;
+ } else if (pcpidev->mode == PI_CCIR_MODE) {
+ val |= (CPI_CTRL_REG_CCIR_EN |
+ CPI_CTRL_REG_CCIR_VSYNC_RESET_EN |
+ CPI_CTRL_REG_CCIR_EXT_VSYNC_EN |
+ CPI_CTRL_REG_CCIR_ECC_ERR_CORRECT_EN);
+ }
+
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+}
+
+static void imx_cpi_config_ctrl_reg1(struct imx_cpi_device *pcpidev,
+ const struct v4l2_mbus_framefmt *format)
+{
+ const struct imx_cpi_plat_data *pdata = pcpidev->pdata;
+ u32 pixel_width;
+ u32 vsync_pulse;
+ u32 val;
+
+ pixel_width = format->width - 1;
+ vsync_pulse = format->width << 1;
+
+ val = CPI_CTRL_REG1_PIXEL_WIDTH(pixel_width) |
+ CPI_CTRL_REG1_VSYNC_PULSE(vsync_pulse);
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg1);
+}
+
+static void imx_cpi_enable(struct imx_cpi_device *pcpidev)
+{
+ const struct imx_cpi_plat_data *pdata = pcpidev->pdata;
+ u32 val;
+
+ /* Enable CPI */
+ val = readl(pcpidev->regs + pdata->interface_ctrl_reg);
+ val |= CPI_CTRL_REG_CPI_EN;
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+
+ /* Disable SYNC Force */
+ val = readl(pcpidev->regs + pdata->interface_ctrl_reg);
+ val &= ~(CPI_CTRL_REG_HSYNC_FORCE_EN | CPI_CTRL_REG_VSYNC_FORCE_EN);
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+}
+
+static void imx_cpi_disable(struct imx_cpi_device *pcpidev)
+{
+ const struct imx_cpi_plat_data *pdata = pcpidev->pdata;
+ u32 val;
+
+ /* Enable Sync Force */
+ val = readl(pcpidev->regs + pdata->interface_ctrl_reg);
+ val |= CPI_CTRL_REG_HSYNC_FORCE_EN | CPI_CTRL_REG_VSYNC_FORCE_EN;
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+
+ /* Disable CPI */
+ val = readl(pcpidev->regs + pdata->interface_ctrl_reg);
+ val &= ~CPI_CTRL_REG_CPI_EN;
+ writel(val, pcpidev->regs + pdata->interface_ctrl_reg);
+
+ /* Disable Pixel Link */
+ val = readl(pcpidev->regs + pdata->if_ctrl_reg);
+ val &= ~(IF_CTRL_REG_PL_VALID | IF_CTRL_REG_PL_ENABLE);
+ writel(val, pcpidev->regs + pdata->if_ctrl_reg);
+}
+
+static struct imx_cpi_device *sd_to_imx_cpi_device(struct v4l2_subdev *sdev)
+{
+ return container_of(sdev, struct imx_cpi_device, sd);
+}
+
+static const struct media_entity_operations imx_cpi_entity_ops = {
+ .link_validate = v4l2_subdev_link_validate,
+ .get_fwnode_pad = v4l2_subdev_get_fwnode_pad_1_to_1,
+};
+
+static int imx_cpi_set_fmt(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_format *sdformat)
+{
+ struct imx_cpi_pix_format const *pcpidev_fmt;
+ struct v4l2_mbus_framefmt *fmt;
+
+ /*
+ * The Parallel cpi can't transcode in any way, the source format
+ * can't be modified.
+ */
+ if (sdformat->pad == V4L2_SUBDEV_1TO1_PADS_SOURCE)
+ return v4l2_subdev_get_fmt(sd, sd_state, sdformat);
+
+ pcpidev_fmt = find_imx_cpi_format(sdformat->format.code);
+ if (!pcpidev_fmt)
+ pcpidev_fmt = &imx_cpi_formats[0];
+
+ fmt = v4l2_subdev_state_get_format(sd_state, sdformat->pad);
+
+ fmt->code = pcpidev_fmt->code;
+ fmt->width = sdformat->format.width;
+ fmt->height = sdformat->format.height;
+ fmt->field = V4L2_FIELD_NONE;
+ fmt->colorspace = sdformat->format.colorspace;
+ fmt->quantization = sdformat->format.quantization;
+ fmt->xfer_func = sdformat->format.xfer_func;
+ fmt->ycbcr_enc = sdformat->format.ycbcr_enc;
+
+ sdformat->format = *fmt;
+
+ /* Propagate the format from sink to source. */
+ fmt = v4l2_subdev_state_get_format(sd_state, V4L2_SUBDEV_1TO1_PADS_SOURCE);
+ *fmt = sdformat->format;
+
+ /* The format on the source pad might change due to unpacking. */
+ fmt->code = pcpidev_fmt->output;
+
+ return 0;
+}
+
+static int imx_cpi_init_state(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state)
+{
+ struct v4l2_subdev_route routes[] = {
+ {
+ .sink_pad = V4L2_SUBDEV_1TO1_PADS_SINK,
+ .sink_stream = 0,
+ .source_pad = V4L2_SUBDEV_1TO1_PADS_SOURCE,
+ .source_stream = 0,
+ .flags = V4L2_SUBDEV_ROUTE_FL_ACTIVE,
+ },
+ };
+ struct v4l2_subdev_krouting routing = {
+ .len_routes = ARRAY_SIZE(routes),
+ .num_routes = ARRAY_SIZE(routes),
+ .routes = routes,
+ };
+ struct v4l2_mbus_framefmt *fmt;
+
+ fmt = v4l2_subdev_state_get_format(state, 0);
+
+ fmt->code = imx_cpi_formats[0].code;
+ fmt->width = 1920;
+ fmt->height = 1080;
+
+ fmt->colorspace = V4L2_COLORSPACE_SMPTE170M;
+ fmt->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(fmt->colorspace);
+ fmt->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(fmt->colorspace);
+ fmt->quantization = V4L2_MAP_QUANTIZATION_DEFAULT(false,
+ fmt->colorspace,
+ fmt->ycbcr_enc);
+
+ return v4l2_subdev_set_routing_with_fmt(sd, state, &routing, fmt);
+}
+
+static int imx_cpi_disable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct imx_cpi_device *pcpidev = sd_to_imx_cpi_device(sd);
+ struct media_pad *sink_pad, *remote_pad;
+ struct device *dev = pcpidev->dev;
+ struct v4l2_subdev *remote_sd;
+ u64 mask;
+ int ret;
+
+ sink_pad = &sd->entity.pads[V4L2_SUBDEV_1TO1_PADS_SINK];
+ remote_pad = media_pad_remote_pad_first(sink_pad);
+ remote_sd = media_entity_to_v4l2_subdev(remote_pad->entity);
+
+ mask = v4l2_subdev_state_xlate_streams(state, V4L2_SUBDEV_1TO1_PADS_SINK,
+ V4L2_SUBDEV_1TO1_PADS_SOURCE,
+ &streams_mask);
+
+ ret = v4l2_subdev_disable_streams(remote_sd, remote_pad->index, mask);
+ if (ret)
+ dev_err(dev, "failed to disable streams on remote subdev: %d\n", ret);
+
+ pcpidev->enabled_streams &= ~streams_mask;
+
+ if (!pcpidev->enabled_streams) {
+ imx_cpi_disable(pcpidev);
+ pm_runtime_put_autosuspend(dev);
+ }
+
+ return 0;
+}
+
+static int imx_cpi_enable_streams(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *state, u32 pad,
+ u64 streams_mask)
+{
+ struct imx_cpi_device *pcpidev = sd_to_imx_cpi_device(sd);
+ const struct imx_cpi_pix_format *pcpidev_fmt;
+ const struct v4l2_mbus_framefmt *format;
+ struct media_pad *sink_pad, *remote_pad;
+ struct device *dev = pcpidev->dev;
+ struct v4l2_subdev *remote_sd;
+ u64 mask;
+ int ret;
+
+ sink_pad = &sd->entity.pads[V4L2_SUBDEV_1TO1_PADS_SINK];
+ remote_pad = media_pad_remote_pad_first(sink_pad);
+ remote_sd = media_entity_to_v4l2_subdev(remote_pad->entity);
+
+ mask = v4l2_subdev_state_xlate_streams(state, V4L2_SUBDEV_1TO1_PADS_SINK,
+ V4L2_SUBDEV_1TO1_PADS_SOURCE,
+ &streams_mask);
+
+ format = v4l2_subdev_state_get_format(state, V4L2_SUBDEV_1TO1_PADS_SINK);
+ pcpidev_fmt = find_imx_cpi_format(format->code);
+
+ if (!pcpidev->enabled_streams) {
+ ret = pm_runtime_resume_and_get(dev);
+ if (ret)
+ return ret;
+
+ imx_cpi_hw_config(pcpidev, pcpidev_fmt);
+ imx_cpi_config_ctrl_reg1(pcpidev, format);
+ imx_cpi_enable(pcpidev);
+ }
+
+ ret = v4l2_subdev_enable_streams(remote_sd, remote_pad->index, mask);
+ if (ret)
+ goto err_cpi_stop;
+
+ pcpidev->enabled_streams |= streams_mask;
+
+ return 0;
+
+err_cpi_stop:
+ /* Stop CSI hardware if no streams are enabled */
+ if (!pcpidev->enabled_streams)
+ imx_cpi_disable(pcpidev);
+
+ pm_runtime_put_autosuspend(dev);
+
+ return ret;
+}
+
+static int imx_cpi_enum_mbus_code(struct v4l2_subdev *sd,
+ struct v4l2_subdev_state *sd_state,
+ struct v4l2_subdev_mbus_code_enum *code)
+{
+ /*
+ * The PARALLEL CPI can't transcode in any way, the source format
+ * is identical to the sink format.
+ */
+ if (code->pad == V4L2_SUBDEV_1TO1_PADS_SOURCE) {
+ struct v4l2_mbus_framefmt *fmt;
+
+ if (code->index > 0)
+ return -EINVAL;
+
+ fmt = v4l2_subdev_state_get_format(sd_state, code->pad);
+ code->code = fmt->code;
+ return 0;
+ }
+
+ if (code->pad != V4L2_SUBDEV_1TO1_PADS_SINK)
+ return -EINVAL;
+
+ if (code->index >= ARRAY_SIZE(imx_cpi_formats))
+ return -EINVAL;
+
+ code->code = imx_cpi_formats[code->index].code;
+
+ return 0;
+}
+
+static int imx_cpi_set_pad_by_ep(struct v4l2_subdev *sd, struct media_pad *pad,
+ struct v4l2_fwnode_endpoint *vep)
+{
+ if (vep->base.port == V4L2_SUBDEV_1TO1_PADS_SINK) {
+ struct imx_cpi_device *pcpidev = sd_to_imx_cpi_device(sd);
+
+ pcpidev->flags = vep->bus.parallel.flags;
+
+ if (vep->bus_type != V4L2_MBUS_PARALLEL)
+ return -EINVAL;
+
+ pad->flags = MEDIA_PAD_FL_SINK | MEDIA_PAD_FL_MUST_CONNECT;
+
+ return 0;
+ }
+
+ if (vep->base.port == V4L2_SUBDEV_1TO1_PADS_SOURCE) {
+ /* Source port */
+ pad->flags = MEDIA_PAD_FL_SOURCE | MEDIA_PAD_FL_MUST_CONNECT;
+ return 0;
+ }
+
+ return -EINVAL;
+}
+
+static const struct v4l2_subdev_video_ops imx_cpi_video_ops = {
+ .s_stream = v4l2_subdev_s_stream_helper,
+};
+
+static const struct v4l2_subdev_pad_ops imx_cpi_pad_ops = {
+ .enum_mbus_code = imx_cpi_enum_mbus_code,
+ .get_fmt = v4l2_subdev_get_fmt,
+ .set_fmt = imx_cpi_set_fmt,
+ .get_frame_desc = v4l2_subdev_get_frame_desc_passthrough,
+ .enable_streams = imx_cpi_enable_streams,
+ .disable_streams = imx_cpi_disable_streams,
+};
+
+static const struct v4l2_subdev_ops imx_cpi_subdev_ops = {
+ .pad = &imx_cpi_pad_ops,
+ .video = &imx_cpi_video_ops,
+};
+
+static const struct v4l2_subdev_internal_ops imx_cpi_internal_ops = {
+ .init_state = imx_cpi_init_state,
+ .set_pad_by_ep = imx_cpi_set_pad_by_ep,
+};
+
+/* ----------------------------------------------------------------------
+ * Suspend/resume
+ */
+
+static int imx_cpi_runtime_suspend(struct device *dev)
+{
+ struct imx_cpi_device *pcpidev = dev_get_drvdata(dev);
+
+ clk_bulk_disable_unprepare(pcpidev->num_clks, pcpidev->clks);
+
+ return 0;
+}
+
+static int imx_cpi_runtime_resume(struct device *dev)
+{
+ struct imx_cpi_device *pcpidev = dev_get_drvdata(dev);
+
+ return clk_bulk_prepare_enable(pcpidev->num_clks, pcpidev->clks);
+}
+
+static const struct dev_pm_ops imx_cpi_pm_ops = {
+ RUNTIME_PM_OPS(imx_cpi_runtime_suspend, imx_cpi_runtime_resume, NULL)
+};
+
+static void imx_cpi_remove(struct platform_device *pdev)
+{
+ struct imx_cpi_device *pcpidev = platform_get_drvdata(pdev);
+
+ media_async_subdev_cleanup(&pcpidev->sd);
+}
+
+static int imx_cpi_probe(struct platform_device *pdev)
+{
+ struct imx_cpi_device *pcpidev;
+ struct device *dev = &pdev->dev;
+ struct v4l2_subdev *sd;
+ int ret;
+
+ pcpidev = devm_kzalloc(dev, sizeof(*pcpidev), GFP_KERNEL);
+ if (!pcpidev)
+ return -ENOMEM;
+
+ pcpidev->dev = dev;
+ platform_set_drvdata(pdev, pcpidev);
+
+ pcpidev->pdata = of_device_get_match_data(dev);
+ pcpidev->mode = PI_GATE_CLOCK_MODE;
+
+ pcpidev->regs = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(pcpidev->regs))
+ return dev_err_probe(dev, PTR_ERR(pcpidev->regs),
+ "Failed to get regs\n");
+
+ pcpidev->num_clks = devm_clk_bulk_get_all(dev, &pcpidev->clks);
+ if (pcpidev->num_clks < 0)
+ return pcpidev->num_clks;
+
+ sd = &pcpidev->sd;
+
+ v4l2_subdev_init(sd, &imx_cpi_subdev_ops);
+
+ sd->internal_ops = &imx_cpi_internal_ops;
+ snprintf(sd->name, sizeof(sd->name), "parallel-%s",
+ dev_name(pcpidev->dev));
+
+ sd->flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
+
+ sd->entity.function = MEDIA_ENT_F_VID_IF_BRIDGE;
+ sd->entity.ops = &imx_cpi_entity_ops;
+
+ sd->dev = pcpidev->dev;
+
+ pm_runtime_use_autosuspend(dev);
+ ret = devm_pm_runtime_enable(dev);
+ if (ret)
+ return ret;
+
+ return media_async_register_subdev(sd);
+}
+
+static const struct of_device_id imx_cpi_of_match[] = {
+ { .compatible = "fsl,imx8qxp-pcif", .data = &imx8qxp_pdata },
+ { },
+};
+
+MODULE_DEVICE_TABLE(of, imx_cpi_of_match);
+
+static struct platform_driver imx_cpi_driver = {
+ .probe = imx_cpi_probe,
+ .remove = imx_cpi_remove,
+ .driver = {
+ .of_match_table = imx_cpi_of_match,
+ .name = "imx-parallel-cpi",
+ .pm = pm_ptr(&imx_cpi_pm_ops),
+ },
+};
+
+module_platform_driver(imx_cpi_driver);
+
+MODULE_DESCRIPTION("i.MX9 Parallel CPI receiver driver");
+MODULE_LICENSE("GPL");
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v7 7/8] arm64: dts: imx8: add camera parallel interface (CPI) node
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
` (5 preceding siblings ...)
2026-07-02 16:04 ` [PATCH v7 6/8] media: nxp: add V4L2 subdev driver for camera parallel interface (CPI) Frank.Li
@ 2026-07-02 16:04 ` Frank.Li
2026-07-02 16:04 ` [PATCH v7 8/8] arm64: dts: imx8qxp-mek: add parallel ov5640 camera support Frank.Li
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:04 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel
From: Frank Li <Frank.Li@nxp.com>
Add camera parallel interface (CPI) node.
Reviewed-by: Guoniu Zhou <guoniu.zhou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Chagnes in v7
- none
changes in v6
- add Guoniu Zhou's review by
changes in v4
- none
changes in v3
- replace csi with cpi.
changes in v2
- update compatible string to match binding's change
---
arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi | 13 +++++++++++
arch/arm64/boot/dts/freescale/imx8qxp-ss-img.dtsi | 27 +++++++++++++++++++++++
2 files changed, 40 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi b/arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi
index a72b2f1c4a1b2..b504f99f6acdb 100644
--- a/arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8-ss-img.dtsi
@@ -222,6 +222,19 @@ irqsteer_parallel: irqsteer@58260000 {
status = "disabled";
};
+ parallel_cpi: cpi@58261000 {
+ compatible = "fsl,imx8qxp-pcif";
+ reg = <0x58261000 0x1000>;
+ clocks = <&pi0_pxl_lpcg IMX_LPCG_CLK_0>,
+ <&pi0_ipg_lpcg IMX_LPCG_CLK_4>;
+ clock-names = "pixel", "ipg";
+ assigned-clocks = <&clk IMX_SC_R_PI_0 IMX_SC_PM_CLK_PER>;
+ assigned-clock-parents = <&clk IMX_SC_R_PI_0_PLL IMX_SC_PM_CLK_PLL>;
+ assigned-clock-rates = <160000000>;
+ power-domains = <&pd IMX_SC_R_PI_0>;
+ status = "disabled";
+ };
+
pi0_ipg_lpcg: clock-controller@58263004 {
compatible = "fsl,imx8qxp-lpcg";
reg = <0x58263004 0x4>;
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-ss-img.dtsi b/arch/arm64/boot/dts/freescale/imx8qxp-ss-img.dtsi
index 232cf25dadfcd..5aae15540d6cb 100644
--- a/arch/arm64/boot/dts/freescale/imx8qxp-ss-img.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-ss-img.dtsi
@@ -62,6 +62,14 @@ isi_in_2: endpoint {
remote-endpoint = <&mipi_csi0_out>;
};
};
+
+ port@4 {
+ reg = <4>;
+
+ isi_in_4: endpoint {
+ remote-endpoint = <¶llel_cpi_out>;
+ };
+ };
};
};
@@ -95,3 +103,22 @@ &jpegenc {
&mipi_csi_1 {
status = "disabled";
};
+
+¶llel_cpi {
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ };
+
+ port@1 {
+ reg = <1>;
+
+ parallel_cpi_out: endpoint {
+ remote-endpoint = <&isi_in_4>;
+ };
+ };
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread* [PATCH v7 8/8] arm64: dts: imx8qxp-mek: add parallel ov5640 camera support
2026-07-02 16:03 [PATCH v7 0/8] media: add new API simple subdev register and add imx parallel camera support Frank.Li
` (6 preceding siblings ...)
2026-07-02 16:04 ` [PATCH v7 7/8] arm64: dts: imx8: add camera parallel interface (CPI) node Frank.Li
@ 2026-07-02 16:04 ` Frank.Li
7 siblings, 0 replies; 13+ messages in thread
From: Frank.Li @ 2026-07-02 16:04 UTC (permalink / raw)
To: Sakari Ailus, Mauro Carvalho Chehab, Michael Riesch,
Laurent Pinchart, Frank Li, Martin Kepplinger-Novakovic,
Rui Miguel Silva, Purism Kernel Team, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sascha Hauer,
Pengutronix Kernel Team, Fabio Estevam
Cc: linux-media, linux-kernel, imx, Guoniu Zhou, devicetree,
linux-arm-kernel
From: Frank Li <Frank.Li@nxp.com>
Add parallel ov5640 nodes in imx8qxp-mek and create overlay file to enable
it because it can work at two mode: MIPI CSI and parallel mode.
Reviewed-by: Guoniu Zhou <guoniu.zhou@nxp.com>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
---
Changes in v7
- none
changes in v6
- add Guoniu's reviewed-by tags
changes in v4
- add hsync-active = <1>
changes in v3
- replace csi with cpi.
- use imx8qxp-mek-ov5640-cpi.dtso since csi use imx8qxp-mek-ov5640-csi.dtso
change in v2
- move ov5640 part to overlay file
- rename to imx8qxp-mek-ov5640-parallel.dtso
- remove data-lanes
---
arch/arm64/boot/dts/freescale/Makefile | 3 +
.../boot/dts/freescale/imx8qxp-mek-ov5640-cpi.dtso | 83 ++++++++++++++++++++++
2 files changed, 86 insertions(+)
diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 001ca3a12c0ae..3b9e9844f11ef 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -554,6 +554,9 @@ dtb-$(CONFIG_ARCH_MXC) += imx8qxp-mek-pcie-ep.dtb
imx8qxp-mek-ov5640-csi-dtbs := imx8qxp-mek.dtb imx8qxp-mek-ov5640-csi.dtbo
dtb-${CONFIG_ARCH_MXC} += imx8qxp-mek-ov5640-csi.dtb
+imx8qxp-mek-ov5640-cpi-dtbs := imx8qxp-mek.dtb imx8qxp-mek-ov5640-cpi.dtbo
+dtb-${CONFIG_ARCH_MXC} += imx8qxp-mek-ov5640-cpi.dtb
+
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-tqma8xqp-mba8xx.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8qxp-tqma8xqps-mb-smarc-2.dtb
dtb-$(CONFIG_ARCH_MXC) += imx8ulp-9x9-evk.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8qxp-mek-ov5640-cpi.dtso b/arch/arm64/boot/dts/freescale/imx8qxp-mek-ov5640-cpi.dtso
new file mode 100644
index 0000000000000..9fbdd798f17d6
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8qxp-mek-ov5640-cpi.dtso
@@ -0,0 +1,83 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Copyright 2025 NXP
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/clock/imx8-lpcg.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/media/video-interfaces.h>
+#include <dt-bindings/pinctrl/pads-imx8qxp.h>
+
+&cm40_i2c {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ov5640_pi: camera@3c {
+ compatible = "ovti,ov5640";
+ reg = <0x3c>;
+ clocks = <&pi0_misc_lpcg IMX_LPCG_CLK_0>;
+ clock-names = "xclk";
+ assigned-clocks = <&pi0_misc_lpcg IMX_LPCG_CLK_0>;
+ assigned-clock-rates = <24000000>;
+ AVDD-supply = <®_2v8>;
+ DOVDD-supply = <®_1v8>;
+ DVDD-supply = <®_1v5>;
+ pinctrl-0 = <&pinctrl_parallel_cpi>;
+ pinctrl-names = "default";
+ powerdown-gpios = <&lsio_gpio3 2 GPIO_ACTIVE_HIGH>;
+ reset-gpios = <&lsio_gpio3 3 GPIO_ACTIVE_LOW>;
+
+ port {
+ ov5640_pi_ep: endpoint {
+ bus-type = <MEDIA_BUS_TYPE_PARALLEL>;
+ bus-width = <8>;
+ hsync-active = <1>;
+ pclk-sample = <1>;
+ remote-endpoint = <¶llel_cpi_in>;
+ vsync-active = <0>;
+ };
+ };
+ };
+};
+
+&iomuxc {
+ pinctrl_parallel_cpi: parallelcpigrp {
+ fsl,pins = <
+ IMX8QXP_CSI_D00_CI_PI_D02 0xc0000041
+ IMX8QXP_CSI_D01_CI_PI_D03 0xc0000041
+ IMX8QXP_CSI_D02_CI_PI_D04 0xc0000041
+ IMX8QXP_CSI_D03_CI_PI_D05 0xc0000041
+ IMX8QXP_CSI_D04_CI_PI_D06 0xc0000041
+ IMX8QXP_CSI_D05_CI_PI_D07 0xc0000041
+ IMX8QXP_CSI_D06_CI_PI_D08 0xc0000041
+ IMX8QXP_CSI_D07_CI_PI_D09 0xc0000041
+
+ IMX8QXP_CSI_MCLK_CI_PI_MCLK 0xc0000041
+ IMX8QXP_CSI_PCLK_CI_PI_PCLK 0xc0000041
+ IMX8QXP_CSI_HSYNC_CI_PI_HSYNC 0xc0000041
+ IMX8QXP_CSI_VSYNC_CI_PI_VSYNC 0xc0000041
+ IMX8QXP_CSI_EN_LSIO_GPIO3_IO02 0xc0000041
+ IMX8QXP_CSI_RESET_LSIO_GPIO3_IO03 0xc0000041
+ >;
+ };
+};
+
+&isi {
+ status = "okay";
+};
+
+¶llel_cpi {
+ status = "okay";
+
+ ports {
+ port@0 {
+ parallel_cpi_in: endpoint {
+ hsync-active = <1>;
+ remote-endpoint = <&ov5640_pi_ep>;
+ };
+ };
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 13+ messages in thread