[PATCH v3 0/2] thermal: imx: Add calibration offset support

[PATCH v3 0/2] thermal: imx: Add calibration offset support

[HaoNing Cheng via B4 Relay]

Some i.MX boards need a small per-design correction to align the
reported CPU temperature with board-level measurements. This series
adds an optional DT property to specify such a calibration offset
and implements the corresponding support in the imx_thermal driver.

Patch 1 documents the new fsl,temp-calibration-offset-millicelsius
property in the i.MX thermal DT binding.

Patch 2 reads this property in the imx_thermal driver and applies
the offset to the i.MX6/6SX/7D calibration formulas. When the
property is absent, the default offset remains 0, preserving the
current behaviour.

Signed-off-by: Haoning CHENG <Haoning.CHENG@cn.bosch.com>
---
Changes in v3:
- dt-bindings: add minimum/maximum (-28580/+28580) for
  temp-calibration-offset-millicelsius, as suggested by Conor Dooley
- Link to v2: https://patch.msgid.link/20260709-b4-symana21-11221-imx-thermal-support-upstream-6-18-v2-0-00ff72495e24@cn.bosch.com

Changes in v2:
- dt-bindings: Removed explicit `$ref: /schemas/types.yaml#/definitions/int32`
  for fsl,temp-calibration-offset-millicelsius; the `-millicelsius` suffix
  already resolves to int32-array via property-units.yaml (Rob).
- dt-bindings: Fixed example indentation.
- driver: Replaced C integer division (/) with DIV_ROUND_CLOSEST() in
  imx_set_alarm_temp() to prevent off-by-one alarm threshold mismatch that
  could cause IRQ storms on i.MX7D.
- driver: Added clamp() bounds check for alarm_value [0, 0x1ff] to avoid
  corrupting adjacent register fields (PANIC_ALARM).
- Link to v1: https://patch.msgid.link/20260709-b4-symana21-11221-imx-thermal-support-upstream-6-18-v1-0-00f88f42930b@cn.bosch.com

To: "Rafael J. Wysocki" <rafael@kernel.org>
To: Daniel Lezcano <daniel.lezcano@linaro.org>
To: Zhang Rui <rui.zhang@intel.com>
To: Lukasz Luba <lukasz.luba@arm.com>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Shawn Guo <shawnguo@kernel.org>
To: Sascha Hauer <s.hauer@pengutronix.de>
To: Pengutronix Kernel Team <kernel@pengutronix.de>
To: Fabio Estevam <festevam@gmail.com>
Cc: linux-pm@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: imx@lists.linux.dev
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org

---
HaoNing Cheng (2):
      dt-bindings: thermal: imx: Document calibration offset property
      thermal/drivers/imx: Add calibration offset support

 .../devicetree/bindings/thermal/imx-thermal.yaml       | 10 ++++++++++
 drivers/thermal/imx_thermal.c                          | 18 +++++++++++++-----
 2 files changed, 23 insertions(+), 5 deletions(-)
---
base-commit: c50a940dcde35c647e097e89a9150003abd48329
change-id: 20260709-b4-symana21-11221-imx-thermal-support-upstream-6-18-a084984deb76

Best regards,
--  
Haoning CHENG <Haoning.CHENG@cn.bosch.com>

[PATCH v3 1/2] dt-bindings: thermal: imx: Document calibration offset property

[HaoNing Cheng via B4 Relay]

From: HaoNing Cheng <Haoning.CHENG@cn.bosch.com>

Some boards need a small per-design correction to align the reported CPU
temperature with board-level measurements.

Document the optional fsl,temp-calibration-offset-millicelsius property,
a signed offset in millicelsius that is added to the calculated sensor
temperature. The property is optional and the existing behaviour is kept
when it is omitted.

Update the binding example to show its usage.

Signed-off-by: HaoNing Cheng <Haoning.CHENG@cn.bosch.com>
---
 Documentation/devicetree/bindings/thermal/imx-thermal.yaml | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
index 949b154856c5..704bf2fa48cf 100644
--- a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
+++ b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
@@ -59,6 +59,15 @@ properties:
   clocks:
     maxItems: 1
 
+  fsl,temp-calibration-offset-millicelsius:
+    maxItems: 1
+    description:
+      A signed calibration offset, in millicelsius, added to the calculated
+      sensor temperature to compensate for board-level measurement
+      differences. When absent, no offset is applied.
+    minimum: -28580
+    maximum: 28580
+
   "#thermal-sensor-cells":
     const: 0
 
@@ -109,6 +118,7 @@ examples:
             nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
             nvmem-cell-names = "calib", "temp_grade";
             clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
+            fsl,temp-calibration-offset-millicelsius = <(-6400)>;
             #thermal-sensor-cells = <0>;
         };
     };

-- 
2.43.0

[PATCH v3 2/2] thermal/drivers/imx: Add calibration offset support

[HaoNing Cheng via B4 Relay]

From: HaoNing Cheng <Haoning.CHENG@cn.bosch.com>

Some boards need a small per-design correction to align the reported CPU
temperature with board-level measurements.

Read the optional fsl,temp-calibration-offset-millicelsius property from
DT and apply it to the i.MX6/6SX/7D calibration formulas. When the
property is not present, the default offset remains 0, preserving the
current behaviour.

Signed-off-by: HaoNing Cheng <Haoning.CHENG@cn.bosch.com>
---
 drivers/thermal/imx_thermal.c | 18 +++++++++++++-----
 1 file changed, 13 insertions(+), 5 deletions(-)

diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index 38c993d1bcb3..8062d34ffed8 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c
@@ -207,6 +207,7 @@ struct imx_thermal_data {
 	struct regmap *tempmon;
 	u32 c1, c2; /* See formula in imx_init_calib() */
 	int temp_max;
+	s32 calibration_offset;
 	int alarm_temp;
 	int last_temp;
 	bool irq_enabled;
@@ -240,10 +241,13 @@ static void imx_set_alarm_temp(struct imx_thermal_data *data,
 
 	data->alarm_temp = alarm_temp;
 
-	if (data->socdata->version == TEMPMON_IMX7D)
-		alarm_value = alarm_temp / 1000 + data->c1 - 25;
-	else
+	if (data->socdata->version == TEMPMON_IMX7D) {
+		alarm_value = DIV_ROUND_UP(alarm_temp - data->calibration_offset,
+					   1000) + data->c1 - 25;
+		alarm_value = clamp(alarm_value, 0, 0x1ff);
+	} else {
 		alarm_value = (data->c2 - alarm_temp) / data->c1;
+	}
 
 	regmap_write(map, soc_data->high_alarm_ctrl + REG_CLR,
 		     soc_data->high_alarm_mask);
@@ -274,7 +278,7 @@ static int imx_get_temp(struct thermal_zone_device *tz, int *temp)
 
 	/* See imx_init_calib() for formula derivation */
 	if (data->socdata->version == TEMPMON_IMX7D)
-		*temp = (n_meas - data->c1 + 25) * 1000;
+		*temp = (n_meas - data->c1 + 25) * 1000 + data->calibration_offset;
 	else
 		*temp = data->c2 - n_meas * data->c1;
 
@@ -413,7 +417,7 @@ static int imx_init_calib(struct platform_device *pdev, u32 ocotp_ana1)
 	temp64 *= 1000; /* to get result in °mC */
 	do_div(temp64, 15423 * n1 - 4148468);
 	data->c1 = temp64;
-	data->c2 = n1 * data->c1 + 28581;
+	data->c2 = n1 * data->c1 + 28581 + data->calibration_offset;
 
 	return 0;
 }
@@ -629,6 +633,10 @@ static int imx_thermal_probe(struct platform_device *pdev)
 
 	platform_set_drvdata(pdev, data);
 
+	of_property_read_s32(dev->of_node,
+			     "fsl,temp-calibration-offset-millicelsius",
+			     &data->calibration_offset);
+
 	if (of_property_present(dev->of_node, "nvmem-cells")) {
 		ret = imx_init_from_nvmem_cells(pdev);
 		if (ret)

-- 
2.43.0

Re: [PATCH v3 1/2] dt-bindings: thermal: imx: Document calibration offset property

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 2015 bytes --]

On Fri, Jul 10, 2026 at 10:50:40AM +0800, HaoNing Cheng via B4 Relay wrote:
> From: HaoNing Cheng <Haoning.CHENG@cn.bosch.com>
> 
> Some boards need a small per-design correction to align the reported CPU
> temperature with board-level measurements.
> 
> Document the optional fsl,temp-calibration-offset-millicelsius property,
> a signed offset in millicelsius that is added to the calculated sensor
> temperature. The property is optional and the existing behaviour is kept
> when it is omitted.
> 
> Update the binding example to show its usage.
> 
> Signed-off-by: HaoNing Cheng <Haoning.CHENG@cn.bosch.com>

Acked-by: Conor Dooley <conor.dooley@microchip.com>
pw-bot: not-applicable

> ---
>  Documentation/devicetree/bindings/thermal/imx-thermal.yaml | 10 ++++++++++
>  1 file changed, 10 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> index 949b154856c5..704bf2fa48cf 100644
> --- a/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> +++ b/Documentation/devicetree/bindings/thermal/imx-thermal.yaml
> @@ -59,6 +59,15 @@ properties:
>    clocks:
>      maxItems: 1
>  
> +  fsl,temp-calibration-offset-millicelsius:
> +    maxItems: 1
> +    description:
> +      A signed calibration offset, in millicelsius, added to the calculated
> +      sensor temperature to compensate for board-level measurement
> +      differences. When absent, no offset is applied.
> +    minimum: -28580
> +    maximum: 28580
> +
>    "#thermal-sensor-cells":
>      const: 0
>  
> @@ -109,6 +118,7 @@ examples:
>              nvmem-cells = <&tempmon_calib>, <&tempmon_temp_grade>;
>              nvmem-cell-names = "calib", "temp_grade";
>              clocks = <&clks IMX6SX_CLK_PLL3_USB_OTG>;
> +            fsl,temp-calibration-offset-millicelsius = <(-6400)>;
>              #thermal-sensor-cells = <0>;
>          };
>      };
> 
> -- 
> 2.43.0
> 
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]