[PATCH v3 0/3] phy: nuvoton: extend MA35D1 USB2 PHY driver for dual-port OTG support

[PATCH v3 0/3] phy: nuvoton: extend MA35D1 USB2 PHY driver for dual-port OTG support

[Joey Lu]

The MA35D1 SoC has two USB PHY ports managed by a shared hardware block:

  - PHY0 (USB0): OTG port shared between the DWC2 gadget controller and
    the EHCI0/OHCI0 host controllers.  A hardware mux automatically routes
    USB0 signals to the correct controller based on the USB ID pin state.

  - PHY1 (USB1): dedicated host-only port for EHCI1/OHCI1.

This series extends the existing phy-ma35d1-usb2.c driver and its binding
to cover both ports and add OTG role-switch support, while keeping full
backward compatibility with existing device trees.

Changes since v2:

  - Dropped patch 1 (nuvoton,ma35d1-reset: add simple-mfd and child node
    support) entirely.  That approach embedded usb-phy@60 as a child of the
    syscon node with a reg property, which broke the established ABI for
    out-of-tree MA35D1 board files.

  - The PHY remains a standalone top-level node as in the mainline binding.
    The existing required properties (clocks, nuvoton,sys, #phy-cells) are
    retained.  No reg property is added.

  - '#phy-cells' is now enum: [0, 1] instead of const: 1.  Boards using
    '#phy-cells = <0>' continue to validate and work unchanged.

  - The DTS usb_phy node is a sibling of sys (not its child), retaining
    clocks and nuvoton,sys, matching the original binding structure.

Joey Lu (3):
  dt-bindings: phy: nuvoton,ma35d1-usb2-phy: extend for dual-port and
    OTG
  arm64: dts: nuvoton: ma35d1: add USB controllers and dual-port PHY
    node
  phy: nuvoton: phy-ma35d1-usb2: extend to dual-port with OTG support

 .../bindings/phy/nuvoton,ma35d1-usb2-phy.yaml |  45 ++-
 .../boot/dts/nuvoton/ma35d1-iot-512m.dts      |  36 +++
 .../boot/dts/nuvoton/ma35d1-som-256m.dts      |  36 +++
 arch/arm64/boot/dts/nuvoton/ma35d1.dtsi       |  65 ++++
 drivers/phy/nuvoton/phy-ma35d1-usb2.c         | 279 +++++++++++++-----
 5 files changed, 384 insertions(+), 77 deletions(-)


base-commit: dc59e4fea9d83f03bad6bddf3fa2e52491777482
-- 
2.43.0

[PATCH v3 1/3] dt-bindings: phy: nuvoton,ma35d1-usb2-phy: extend for dual-port and OTG

[Joey Lu]

The MA35D1 exposes two USB PHY ports (PHY0 and PHY1) managed by the
same hardware block (USBPMISCR register in the system-management syscon).
PHY0 is shared between the DWC2 gadget controller and EHCI0/OHCI0
through an automatic hardware mux that follows the USB ID pin; PHY1 is
dedicated to EHCI1/OHCI1.  Because both ports share the same register
topology a single binding and driver should cover both.

Changing '#phy-cells' from const: 0 to enum: [0, 1] lets consumers name
the port they need while preserving backward compatibility: boards already
using '#phy-cells = <0>' continue to validate and function unchanged.

The two new optional properties:
  - nuvoton,rcalcode: the resistor calibration trim code is determined at
    board design time to match the PCB trace impedance.
  - nuvoton,oc-active-high: the over-current detect polarity depends on
    the choice of VBUS power switch.

Signed-off-by: Joey Lu <a0987203069@gmail.com>
---
 .../bindings/phy/nuvoton,ma35d1-usb2-phy.yaml | 45 +++++++++++++++++--
 1 file changed, 42 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml b/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml
index fff858c909a0..191d1b2272ec 100644
--- a/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/nuvoton,ma35d1-usb2-phy.yaml
@@ -8,6 +8,18 @@ title: Nuvoton MA35D1 USB2 phy
 
 maintainers:
   - Hui-Ping Chen <hpchen0nvt@gmail.com>
+  - Joey Lu <yclu4@nuvoton.com>
+
+description:
+  USB 2.0 PHY for the Nuvoton MA35D1 SoC. The PHY node is a standalone
+  platform device that accesses the USB PHY control registers inside the
+  system-management syscon block via the nuvoton,sys phandle.
+
+  PHY0 is the OTG port whose signals are routed to either the DWC2 gadget
+  controller or the EHCI0/OHCI0 host controller by a hardware mux that
+  follows the USB ID pin automatically.
+
+  PHY1 is a dedicated host-only port used by EHCI1/OHCI1.
 
 properties:
   compatible:
@@ -15,7 +27,12 @@ properties:
       - nuvoton,ma35d1-usb2-phy
 
   "#phy-cells":
-    const: 0
+    enum: [0, 1]
+    description:
+      When 0, the node exposes PHY0 only and consumers reference it
+      with no cell argument. When 1, the single cell selects the port,
+      with 0 for the OTG port (USB0, shared with DWC2 gadget controller)
+      and 1 for the host-only port (USB1).
 
   clocks:
     maxItems: 1
@@ -23,7 +40,29 @@ properties:
   nuvoton,sys:
     $ref: /schemas/types.yaml#/definitions/phandle
     description:
-      phandle to syscon for checking the PHY clock status.
+      Phandle to the system-management syscon node providing access to the
+      USB PHY control registers.
+
+  nuvoton,rcalcode:
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    minItems: 2
+    maxItems: 2
+    items:
+      minimum: 0
+      maximum: 15
+    description:
+      Resistor calibration trim codes for PHY0 and PHY1 respectively.
+      Each 4-bit value is written to the RCALCODE field in USBPMISCR and
+      adjusts the PHY's internal termination resistance. Both entries must
+      be supplied when this property is present; when absent the hardware
+      reset default is used for each port.
+
+  nuvoton,oc-active-high:
+    type: boolean
+    description:
+      When present, the over-current detect input from the VBUS power switch
+      is treated as active-high. The default (property absent) is active-low.
+      This setting is shared by both USB host ports.
 
 required:
   - compatible
@@ -39,7 +78,7 @@ examples:
 
     usb_phy: usb-phy {
         compatible = "nuvoton,ma35d1-usb2-phy";
-        clocks = <&clk USBD_GATE>;
+        clocks = <&clk HUSBH0_GATE>;
         nuvoton,sys = <&sys>;
         #phy-cells = <0>;
     };
-- 
2.43.0

Re: [PATCH v3 1/3] dt-bindings: phy: nuvoton,ma35d1-usb2-phy: extend for dual-port and OTG

[Krzysztof Kozlowski]

On Wed, Jul 08, 2026 at 06:36:04PM +0800, Joey Lu wrote:
> +  nuvoton,oc-active-high:
> +    type: boolean
> +    description:
> +      When present, the over-current detect input from the VBUS power switch
> +      is treated as active-high. The default (property absent) is active-low.
> +      This setting is shared by both USB host ports.
>  
>  required:
>    - compatible
> @@ -39,7 +78,7 @@ examples:
>  
>      usb_phy: usb-phy {
>          compatible = "nuvoton,ma35d1-usb2-phy";
> -        clocks = <&clk USBD_GATE>;
> +        clocks = <&clk HUSBH0_GATE>;

This change is really redundant. Instead, add optional properties like
nuvoton,rcalcode and nuvoton,oc-active-high.

The rest looks good, so with above change:

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

[PATCH v3 2/3] arm64: dts: nuvoton: ma35d1: add USB controllers and dual-port PHY node

[Joey Lu]

PHY0 is referenced by both the DWC2 gadget and EHCI0/OHCI0 nodes because
the USB0 signal lines are physically wired to all three controllers
simultaneously; the on-chip hardware mux, driven by the USB ID pin,
selects which controller is active.  The PHY framework handles this shared
reference correctly.

OHCI companion nodes are required alongside their EHCI counterparts so
that the EHCI driver can hand off full-speed and low-speed devices that
cannot operate at high speed; without them those device classes fail to
enumerate.

The board files add pinctrl entries for the HSUSB signals (VBUSVLD,
PWREN, OVC) because these lines are routed through multiplexed pads and
must be explicitly configured for USB function.

Signed-off-by: Joey Lu <a0987203069@gmail.com>
---
 .../boot/dts/nuvoton/ma35d1-iot-512m.dts      | 36 ++++++++++
 .../boot/dts/nuvoton/ma35d1-som-256m.dts      | 36 ++++++++++
 arch/arm64/boot/dts/nuvoton/ma35d1.dtsi       | 65 +++++++++++++++++++
 3 files changed, 137 insertions(+)

diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts b/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts
index 78534d613486..0a068abda6e0 100644
--- a/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1-iot-512m.dts
@@ -97,6 +97,16 @@ pinctrl_uart14: uart14-pins {
 			power-source = <1>;
 		};
 	};
+
+	hsusb {
+		pinctrl_hsusb: hsusb-pins {
+			nuvoton,pins = <5 15 1>, /* VBUSVLD */
+				       <11 12 9>, /* PWREN */
+				       <11 13 9>; /* OVC */
+			bias-disable;
+			power-source = <1>;
+		};
+	};
 };
 
 &uart0 {
@@ -151,3 +161,29 @@ eth_phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
+
+&usb_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hsusb>;
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts b/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts
index a029b660e8dc..7f1e6d2a1fc2 100644
--- a/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1-som-256m.dts
@@ -100,6 +100,16 @@ pinctrl_uart16: uart16-pins {
 			power-source = <1>;
 		};
 	};
+
+	hsusb {
+		pinctrl_hsusb: hsusb-pins {
+			nuvoton,pins = <5 15 1>, /* VBUSVLD */
+				       <11 12 9>, /* PWREN */
+				       <11 13 9>; /* OVC */
+			bias-disable;
+			power-source = <1>;
+		};
+	};
 };
 
 &uart0 {
@@ -153,3 +163,29 @@ eth_phy1: ethernet-phy@1 {
 		reg = <1>;
 	};
 };
+
+&usb_phy {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pinctrl_hsusb>;
+	status = "okay";
+};
+
+&usb {
+	status = "okay";
+};
+
+&ehci0 {
+	status = "okay";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ohci0 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi b/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
index 7228ad4735b5..5a7a39b1b514 100644
--- a/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
+++ b/arch/arm64/boot/dts/nuvoton/ma35d1.dtsi
@@ -88,6 +88,14 @@ sys: system-management@40460000 {
 			#reset-cells = <1>;
 		};
 
+		usb_phy: usb-phy {
+			compatible = "nuvoton,ma35d1-usb2-phy";
+			clocks = <&clk HUSBH0_GATE>;
+			nuvoton,sys = <&sys>;
+			#phy-cells = <1>;
+			status = "disabled";
+		};
+
 		clk: clock-controller@40460200 {
 			compatible = "nuvoton,ma35d1-clk";
 			reg = <0x00000000 0x40460200 0x0 0x100>;
@@ -431,5 +439,62 @@ mdio1: mdio {
 				#size-cells = <0>;
 			};
 		};
+
+		usb: usb@40200000 {
+			compatible = "snps,dwc2";
+			reg = <0x0 0x40200000 0x0 0x1000>;
+			interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk USBD_GATE>;
+			clock-names = "otg";
+			phys = <&usb_phy 0>;
+			phy-names = "usb2-phy";
+			dr_mode = "peripheral";
+			g-np-tx-fifo-size = <16>;
+			g-rx-fifo-size = <0x100>;
+			g-tx-fifo-size = <256 256 64 64 64 32 32 32>;
+			status = "disabled";
+		};
+
+		ehci0: usb@40140000 {
+			compatible = "generic-ehci";
+			reg = <0x0 0x40140000 0x0 0x1000>;
+			interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk HUSBH0_GATE>;
+			phys = <&usb_phy 0>;
+			phy-names = "usb";
+			companion = <&ohci0>;
+			status = "disabled";
+		};
+
+		ehci1: usb@401c0000 {
+			compatible = "generic-ehci";
+			reg = <0x0 0x401c0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk HUSBH1_GATE>;
+			phys = <&usb_phy 1>;
+			phy-names = "usb";
+			companion = <&ohci1>;
+			status = "disabled";
+		};
+
+		ohci0: usb@40150000 {
+			compatible = "generic-ohci";
+			reg = <0x0 0x40150000 0x0 0x1000>;
+			interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk HUSBH0_GATE>;
+			phys = <&usb_phy 0>;
+			phy-names = "usb";
+			status = "disabled";
+		};
+
+		ohci1: usb@401d0000 {
+			compatible = "generic-ohci";
+			reg = <0x0 0x401d0000 0x0 0x1000>;
+			interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&clk HUSBH1_GATE>;
+			phys = <&usb_phy 1>;
+			phy-names = "usb";
+			status = "disabled";
+		};
 	};
 };
-- 
2.43.0

[PATCH v3 3/3] phy: nuvoton: phy-ma35d1-usb2: extend to dual-port with OTG support

[Joey Lu]

PHY0 and PHY1 use the same power-on/reset sequence in USBPMISCR, with
PHY1 control bits shifted 16 positions relative to PHY0.  A separate
driver for PHY1 would duplicate this logic, so the existing driver is
extended to manage both ports.

The original driver polled only DEVCKSTB after releasing PHY0 from
reset.  When USB0 operates in host mode (USB ID pin floating or tied
high) only HSTCKSTB and CK12MSTB assert; DEVCKSTB never sets.  Polling
exclusively for DEVCKSTB in host mode causes a 1 ms timeout on every
phy_init() call from the EHCI driver.  The init callback is changed to
accept either host-mode or device-mode clock stability, whichever
asserts first.

The power_on and power_off callbacks are replaced by a single init
callback that handles PHY reset and clock-stable polling, because
there is no PHY-specific clock gate on MA35D1; the PHY analog block
derives its reference from the HXT crystal.

A read-only USB role switch is registered for PHY0 to expose the USB0
role to userspace via the standard role-switch sysfs interface.  The
.set callback returns -EOPNOTSUPP because the hardware mux is fully
automatic with no software override path.

Signed-off-by: Joey Lu <a0987203069@gmail.com>
---
 drivers/phy/nuvoton/phy-ma35d1-usb2.c | 279 +++++++++++++++++++-------
 1 file changed, 205 insertions(+), 74 deletions(-)

diff --git a/drivers/phy/nuvoton/phy-ma35d1-usb2.c b/drivers/phy/nuvoton/phy-ma35d1-usb2.c
index 9a459b700ed4..e2eac4f8c5bf 100644
--- a/drivers/phy/nuvoton/phy-ma35d1-usb2.c
+++ b/drivers/phy/nuvoton/phy-ma35d1-usb2.c
@@ -1,11 +1,16 @@
 // SPDX-License-Identifier: GPL-2.0
 /*
- * Copyright (C) 2024 Nuvoton Technology Corp.
+ * Nuvoton MA35D1 USB 2.0 PHY driver
+ *
+ * Supports PHY0 (USB0 OTG port, shared between DWC2 gadget and EHCI0/OHCI0)
+ * and PHY1 (USB1 host-only port, used by EHCI1/OHCI1). The hardware mux on
+ * PHY0 switches automatically via the USB ID pin.
+ *
+ * Copyright (C) 2026 Nuvoton Technology Corp.
  */
 #include <linux/bitfield.h>
 #include <linux/clk.h>
 #include <linux/delay.h>
-#include <linux/io.h>
 #include <linux/kernel.h>
 #include <linux/mfd/syscon.h>
 #include <linux/module.h>
@@ -13,131 +18,257 @@
 #include <linux/phy/phy.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
+#include <linux/usb/role.h>
 
-/* USB PHY Miscellaneous Control Register */
-#define MA35_SYS_REG_USBPMISCR	0x60
-#define PHY0POR			BIT(0)  /* PHY Power-On Reset Control Bit */
-#define PHY0SUSPEND			BIT(1)  /* PHY Suspend; 0: suspend, 1: operaion */
-#define PHY0COMN			BIT(2)  /* PHY Common Block Power-Down Control */
-#define PHY0DEVCKSTB			BIT(10) /* PHY 60 MHz UTMI clock stable bit */
+#define MA35_SYS_PWRONOTP		0x04
+#define PWRONOTP_USBP0ID		BIT(16)
+
+#define MA35_SYS_USBPMISCR		0x60
+#define USBPMISCR_PHY_POR(n)		BIT(0  + (n) * 16)
+#define USBPMISCR_PHY_SUSPEND(n)	BIT(1  + (n) * 16)
+#define USBPMISCR_PHY_COMN(n)		BIT(2  + (n) * 16)
+#define USBPMISCR_PHY_HSTCKSTB(n)	BIT(8  + (n) * 16)
+#define USBPMISCR_PHY_CK12MSTB(n)	BIT(9  + (n) * 16)
+#define USBPMISCR_PHY_DEVCKSTB(n)	BIT(10 + (n) * 16)
+/* Mask for control bits (POR, SUSPEND, COMN) */
+#define USBPMISCR_PHY_CTL_MASK(n)	(0x7u << ((n) * 16))
+/* Host-mode ready */
+#define USBPMISCR_PHY_HOST_READY(n)	(USBPMISCR_PHY_SUSPEND(n)  | \
+					 USBPMISCR_PHY_HSTCKSTB(n) | \
+					 USBPMISCR_PHY_CK12MSTB(n))
+/* Device-mode ready */
+#define USBPMISCR_PHY_DEV_READY(n)	(USBPMISCR_PHY_SUSPEND(n)  | \
+					 USBPMISCR_PHY_DEVCKSTB(n))
+/* RCALCODE: 4-bit resistor trim */
+#define USBPMISCR_RCAL_SHIFT(n)		(12 + (n) * 16)
+#define USBPMISCR_RCAL_MASK(n)		GENMASK(USBPMISCR_RCAL_SHIFT(n) + 3, \
+						USBPMISCR_RCAL_SHIFT(n))
+
+#define MA35_SYS_MISCFCR0		0x70
+/* USB host over-current detect polarity (shared, both ports) */
+#define MISCFCR0_UHOVRCURH		BIT(12)
+
+#define MA35_PHY_NUM			2
+
+struct ma35_phy_port {
+	struct phy *phy;
+	unsigned int idx;
+};
 
 struct ma35_usb_phy {
-	struct clk *clk;
 	struct device *dev;
 	struct regmap *sysreg;
+	struct ma35_phy_port port[MA35_PHY_NUM];
+	struct usb_role_switch *role_sw;
 };
 
-static int ma35_usb_phy_power_on(struct phy *phy)
+static int ma35_usb_phy_init(struct phy *phy)
 {
-	struct ma35_usb_phy *p_phy = phy_get_drvdata(phy);
+	struct ma35_phy_port *port = phy_get_drvdata(phy);
+	struct ma35_usb_phy *p = container_of(port - port->idx,
+					      struct ma35_usb_phy, port[0]);
+	unsigned int n = port->idx;
 	unsigned int val;
 	int ret;
 
-	ret = clk_prepare_enable(p_phy->clk);
-	if (ret < 0) {
-		dev_err(p_phy->dev, "Failed to enable PHY clock: %d\n", ret);
-		return ret;
-	}
+	regmap_read(p->sysreg, MA35_SYS_USBPMISCR, &val);
 
-	regmap_read(p_phy->sysreg, MA35_SYS_REG_USBPMISCR, &val);
-	if (val & PHY0SUSPEND) {
-		/*
-		 * USB PHY0 is in operation mode already
-		 * make sure USB PHY 60 MHz UTMI Interface Clock ready
-		 */
-		ret = regmap_read_poll_timeout(p_phy->sysreg, MA35_SYS_REG_USBPMISCR, val,
-						val & PHY0DEVCKSTB, 10, 1000);
-		if (ret == 0)
-			return 0;
-	}
+	if (val & USBPMISCR_PHY_SUSPEND(n))
+		return 0;
 
-	/*
-	 * reset USB PHY0.
-	 * wait until USB PHY0 60 MHz UTMI Interface Clock ready
-	 */
-	regmap_update_bits(p_phy->sysreg, MA35_SYS_REG_USBPMISCR, 0x7, (PHY0POR | PHY0SUSPEND));
+	regmap_update_bits(p->sysreg, MA35_SYS_USBPMISCR,
+			   USBPMISCR_PHY_CTL_MASK(n),
+			   USBPMISCR_PHY_POR(n) | USBPMISCR_PHY_SUSPEND(n));
 	udelay(20);
 
-	/* make USB PHY0 enter operation mode */
-	regmap_update_bits(p_phy->sysreg, MA35_SYS_REG_USBPMISCR, 0x7, PHY0SUSPEND);
+	regmap_update_bits(p->sysreg, MA35_SYS_USBPMISCR,
+			   USBPMISCR_PHY_CTL_MASK(n),
+			   USBPMISCR_PHY_SUSPEND(n));
 
-	/* make sure USB PHY 60 MHz UTMI Interface Clock ready */
-	ret = regmap_read_poll_timeout(p_phy->sysreg, MA35_SYS_REG_USBPMISCR, val,
-					val & PHY0DEVCKSTB, 10, 1000);
-	if (ret == -ETIMEDOUT) {
-		dev_err(p_phy->dev, "Check PHY clock, Timeout: %d\n", ret);
-		clk_disable_unprepare(p_phy->clk);
+	if (n == 0) {
+		ret = regmap_read_poll_timeout(p->sysreg, MA35_SYS_USBPMISCR,
+					       val,
+					       ((val & USBPMISCR_PHY_HOST_READY(0)) ==
+						USBPMISCR_PHY_HOST_READY(0)) ||
+					       ((val & USBPMISCR_PHY_DEV_READY(0)) ==
+						USBPMISCR_PHY_DEV_READY(0)),
+					       10, 1000);
+	} else {
+		ret = regmap_read_poll_timeout(p->sysreg, MA35_SYS_USBPMISCR,
+					       val,
+					       (val & USBPMISCR_PHY_HOST_READY(n)) ==
+					       USBPMISCR_PHY_HOST_READY(n),
+					       10, 1000);
+	}
+
+	if (ret) {
+		dev_err(p->dev, "USB PHY%u clock not stable (USBPMISCR=0x%08x)\n",
+			n, val);
 		return ret;
 	}
 
 	return 0;
 }
 
-static int ma35_usb_phy_power_off(struct phy *phy)
+static const struct phy_ops ma35_usb_phy_ops = {
+	.init		= ma35_usb_phy_init,
+	.owner		= THIS_MODULE,
+};
+
+static int ma35_role_sw_set(struct usb_role_switch *sw, enum usb_role role)
+{
+	return -EOPNOTSUPP;
+}
+
+static enum usb_role ma35_role_sw_get(struct usb_role_switch *sw)
 {
-	struct ma35_usb_phy *p_phy = phy_get_drvdata(phy);
+	struct ma35_usb_phy *p = usb_role_switch_get_drvdata(sw);
+	u32 val;
+
+	regmap_read(p->sysreg, MA35_SYS_PWRONOTP, &val);
+
+	return (val & PWRONOTP_USBP0ID) ? USB_ROLE_HOST : USB_ROLE_DEVICE;
+}
+
+static int ma35_role_switch_init(struct platform_device *pdev,
+				 struct ma35_usb_phy *p)
+{
+	struct usb_role_switch_desc sw_desc = {0};
+
+	sw_desc.set = ma35_role_sw_set;
+	sw_desc.get = ma35_role_sw_get;
+	sw_desc.allow_userspace_control = true;
+	sw_desc.driver_data = p;
+	sw_desc.fwnode = dev_fwnode(&pdev->dev);
+
+	p->role_sw = usb_role_switch_register(&pdev->dev, &sw_desc);
+	if (IS_ERR(p->role_sw))
+		return dev_err_probe(&pdev->dev, PTR_ERR(p->role_sw),
+				     "failed to register role switch\n");
 
-	clk_disable_unprepare(p_phy->clk);
 	return 0;
 }
 
-static const struct phy_ops ma35_usb_phy_ops = {
-	.power_on = ma35_usb_phy_power_on,
-	.power_off = ma35_usb_phy_power_off,
-	.owner = THIS_MODULE,
-};
+static void ma35_role_switch_exit(struct ma35_usb_phy *p)
+{
+	if (p->role_sw) {
+		usb_role_switch_unregister(p->role_sw);
+		p->role_sw = NULL;
+	}
+}
+
+static struct phy *ma35_usb_phy_xlate(struct device *dev,
+				      const struct of_phandle_args *args)
+{
+	struct ma35_usb_phy *p = dev_get_drvdata(dev);
+	unsigned int idx;
+
+	if (args->args_count == 0)
+		idx = 0;
+	else
+		idx = args->args[0];
+
+	if (idx >= MA35_PHY_NUM)
+		return ERR_PTR(-EINVAL);
+
+	return p->port[idx].phy;
+}
 
 static int ma35_usb_phy_probe(struct platform_device *pdev)
 {
 	struct phy_provider *provider;
-	struct ma35_usb_phy *p_phy;
-	struct phy *phy;
+	struct ma35_usb_phy *p;
+	struct clk *clk;
+	int n, ret;
+	u32 code;
 
-	p_phy = devm_kzalloc(&pdev->dev, sizeof(*p_phy), GFP_KERNEL);
-	if (!p_phy)
+	p = devm_kzalloc(&pdev->dev, sizeof(*p), GFP_KERNEL);
+	if (!p)
 		return -ENOMEM;
 
-	p_phy->dev = &pdev->dev;
-	platform_set_drvdata(pdev, p_phy);
+	p->dev = &pdev->dev;
+	platform_set_drvdata(pdev, p);
+
+	p->sysreg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
+						     "nuvoton,sys");
+	if (IS_ERR(p->sysreg))
+		return dev_err_probe(&pdev->dev, PTR_ERR(p->sysreg),
+				     "failed to get SYS regmap\n");
+
+	clk = devm_clk_get_enabled(&pdev->dev, NULL);
+	if (IS_ERR(clk))
+		return dev_err_probe(&pdev->dev, PTR_ERR(clk),
+				     "failed to get clock\n");
 
-	p_phy->sysreg = syscon_regmap_lookup_by_phandle(pdev->dev.of_node, "nuvoton,sys");
-	if (IS_ERR(p_phy->sysreg))
-		return dev_err_probe(&pdev->dev, PTR_ERR(p_phy->sysreg),
-				     "Failed to get SYS registers\n");
+	for (n = 0; n < MA35_PHY_NUM; n++) {
+		if (of_property_read_u32_index(pdev->dev.of_node,
+					       "nuvoton,rcalcode", n, &code))
+			continue;
 
-	p_phy->clk = of_clk_get(pdev->dev.of_node, 0);
-	if (IS_ERR(p_phy->clk))
-		return dev_err_probe(&pdev->dev, PTR_ERR(p_phy->clk),
-				     "failed to find usb_phy clock\n");
+		if (code > 15)
+			return dev_err_probe(&pdev->dev, -EINVAL,
+					     "rcalcode[%d] %u out of range (0-15)\n",
+					     n, code);
 
-	phy = devm_phy_create(&pdev->dev, NULL, &ma35_usb_phy_ops);
-	if (IS_ERR(phy))
-		return dev_err_probe(&pdev->dev, PTR_ERR(phy), "Failed to create PHY\n");
+		regmap_update_bits(p->sysreg, MA35_SYS_USBPMISCR,
+				   USBPMISCR_RCAL_MASK(n),
+				   code << USBPMISCR_RCAL_SHIFT(n));
+	}
+
+	if (of_property_read_bool(pdev->dev.of_node, "nuvoton,oc-active-high"))
+		regmap_update_bits(p->sysreg, MA35_SYS_MISCFCR0,
+				   MISCFCR0_UHOVRCURH, MISCFCR0_UHOVRCURH);
+
+	for (n = 0; n < MA35_PHY_NUM; n++) {
+		p->port[n].idx = n;
+
+		p->port[n].phy = devm_phy_create(&pdev->dev, pdev->dev.of_node,
+						 &ma35_usb_phy_ops);
+		if (IS_ERR(p->port[n].phy))
+			return dev_err_probe(&pdev->dev, PTR_ERR(p->port[n].phy),
+					     "failed to create PHY%d\n", n);
 
-	phy_set_drvdata(phy, p_phy);
+		phy_set_drvdata(p->port[n].phy, &p->port[n]);
+	}
+
+	ret = ma35_role_switch_init(pdev, p);
+	if (ret)
+		return ret;
 
-	provider = devm_of_phy_provider_register(&pdev->dev, of_phy_simple_xlate);
-	if (IS_ERR(provider))
+	provider = devm_of_phy_provider_register(&pdev->dev, ma35_usb_phy_xlate);
+	if (IS_ERR(provider)) {
+		ma35_role_switch_exit(p);
 		return dev_err_probe(&pdev->dev, PTR_ERR(provider),
-				     "Failed to register PHY provider\n");
+				     "failed to register PHY provider\n");
+	}
+
 	return 0;
 }
 
+static void ma35_usb_phy_remove(struct platform_device *pdev)
+{
+	struct ma35_usb_phy *p = platform_get_drvdata(pdev);
+
+	ma35_role_switch_exit(p);
+}
+
 static const struct of_device_id ma35_usb_phy_of_match[] = {
-	{ .compatible = "nuvoton,ma35d1-usb2-phy", },
-	{ },
+	{ .compatible = "nuvoton,ma35d1-usb2-phy" },
+	{ /* sentinel */ }
 };
 MODULE_DEVICE_TABLE(of, ma35_usb_phy_of_match);
 
 static struct platform_driver ma35_usb_phy_driver = {
 	.probe		= ma35_usb_phy_probe,
-	.driver	= {
-		.name	= "ma35d1-usb2-phy",
-		.of_match_table = ma35_usb_phy_of_match,
+	.remove		= ma35_usb_phy_remove,
+	.driver		= {
+		.name		= "ma35d1-usb2-phy",
+		.of_match_table	= ma35_usb_phy_of_match,
 	},
 };
 module_platform_driver(ma35_usb_phy_driver);
 
 MODULE_DESCRIPTION("Nuvoton ma35d1 USB2.0 PHY driver");
 MODULE_AUTHOR("Hui-Ping Chen <hpchen0nvt@gmail.com>");
+MODULE_AUTHOR("Joey Lu <a0987203069@gmail.com>");
 MODULE_LICENSE("GPL");
-- 
2.43.0