* [PATCH v4 2/2] arm64: dts: rockchip: Add ArmSoM CM5 and CM5-IO
2026-07-17 6:59 [PATCH v4 0/2] arm64: dts: rockchip: Add ArmSoM CM5 and CM5-IO Jiaxing Hu
2026-07-17 6:59 ` [PATCH v4 1/2] dt-bindings: arm: " Jiaxing Hu
@ 2026-07-17 6:59 ` Jiaxing Hu
1 sibling, 0 replies; 3+ messages in thread
From: Jiaxing Hu @ 2026-07-17 6:59 UTC (permalink / raw)
To: heiko, robh, krzk+dt, conor+dt
Cc: devicetree, linux-rockchip, linux-arm-kernel, linux-kernel,
Jiaxing Hu
Add the ArmSoM CM5, an RK3576 compute module (rk3576-armsom-cm5.dtsi),
and its CM5-IO carrier (rk3576-armsom-cm5-io.dts). The module has the
RK806 PMIC, HYM8563 RTC, eMMC, GMAC0 with an on-module MotorComm YT8531
PHY, and the SDIO bus for the on-module WiFi. The carrier adds HDMI, a
GbE RJ45, two USB-A ports behind a USB3 hub, USB-C with FUSB302 and DP
alt-mode, a PCIe 2.0 x1 M.2 slot, microSD, status LEDs and a 40-pin
header.
The YT8531 has no crystal, so it uses the SoC 25 MHz reference output,
described on the gmac node as clk_mac_refout. Its reset is described at
the MDIO bus level: mdiobus releases a bus level reset before it scans
for PHY IDs, whereas a per-PHY reset-gpios is only applied once the PHY
has been found, which never happens while the PHY is still in reset.
Signed-off-by: Jiaxing Hu <gahing@gahingwoo.com>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3576-armsom-cm5-io.dts | 402 +++++++++++++
.../boot/dts/rockchip/rk3576-armsom-cm5.dtsi | 558 ++++++++++++++++++
3 files changed, 961 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
create mode 100644 arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index cb55c6b70..3ec0b6e20 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -165,6 +165,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-display-vz.dtbo
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3568-wolfvision-pf5-io-expander.dtbo
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-100ask-dshanpi-a1.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-cm5-io.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-armsom-sige5-v1.2-wifibt.dtbo
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3576-evb1-v10.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
new file mode 100644
index 000000000..40d9be0c6
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
@@ -0,0 +1,402 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * ArmSoM CM5-IO - official carrier board for the ArmSoM CM5 (RK3576) module.
+ *
+ * Carrier provides:
+ * - Full-size HDMI 2.1 (HDMI TX via HDPTX PHY)
+ * - Gigabit Ethernet RJ45 (GMAC0 + on-module YT8531)
+ * - 2x USB-A behind a USB3 hub (combphy1 + u2phy1)
+ * - USB-C with PD/altmode (FUSB302 on i2c0, combphy0 + USBDP PHY)
+ * - M.2 PCIe 2.0 x1 slot (combphy0 as PCIe lane)
+ * - microSD card slot
+ * - Green/red status LEDs, 40-pin RPi-compatible header
+ * - 12 V DC barrel jack
+ *
+ * Copyright (c) 2024 ArmSoM
+ * Copyright (c) 2026 Jiaxing Hu <gahing@gahingwoo.com>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include <dt-bindings/usb/pd.h>
+#include "rk3576-armsom-cm5.dtsi"
+
+/ {
+ model = "ArmSoM CM5-IO";
+ compatible = "armsom,cm5-io", "armsom,cm5", "rockchip,rk3576";
+
+ aliases {
+ ethernet0 = &gmac0;
+ mmc0 = &sdhci;
+ mmc1 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial0:1500000n8";
+ };
+
+ /* Full-size HDMI Type-A connector, driven by the SoC HDMI TX. */
+ hdmi-con {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi_out_con>;
+ };
+ };
+ };
+
+ /*
+ * Carrier status LEDs (schematic ARMSOM-CM5-IO-1V1_20240829):
+ * green - GPIO2 PD0 (net LED_GREEN_EN)
+ * red - GPIO2 PD1 (net LED_RED_EN)
+ */
+ leds: leds {
+ compatible = "gpio-leds";
+
+ led_green: led-green {
+ color = <LED_COLOR_ID_GREEN>;
+ function = LED_FUNCTION_STATUS;
+ gpios = <&gpio2 RK_PD0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_green_en>;
+ default-state = "on";
+ };
+
+ led_red: led-red {
+ color = <LED_COLOR_ID_RED>;
+ function = LED_FUNCTION_FAULT;
+ gpios = <&gpio2 RK_PD1 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&led_red_en>;
+ default-state = "off";
+ };
+ };
+
+ /* Carrier power tree: 12 V barrel jack -> 5 V -> peripheral rails. */
+ vcc_12v0_dcin: regulator-vcc-12v0-dcin {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_12v0_dcin";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <12000000>;
+ regulator-max-microvolt = <12000000>;
+ };
+
+ vcc_5v0_sys: regulator-vcc-5v0-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v0_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_12v0_dcin>;
+ };
+
+ vcc_5v0_device: regulator-vcc-5v0-device {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_5v0_device";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_12v0_dcin>;
+ };
+
+ /* PCIe 3.3 V for the M.2 slot, gated by GPIO0 PC3. */
+ vcc_3v3_pcie: regulator-vcc-3v3-pcie {
+ compatible = "regulator-fixed";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_pwr_en>;
+ regulator-name = "vcc_3v3_pcie";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ enable-active-high;
+ gpios = <&gpio0 RK_PC3 GPIO_ACTIVE_HIGH>;
+ startup-delay-us = <5000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ /* USB-C / OTG 5 V, gated by GPIO2 PB6. */
+ vcc_5v0_typec0: regulator-vcc-5v0-typec0 {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio2 RK_PB6 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_otg0_pwren>;
+ regulator-name = "vcc_5v0_typec0";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v0_device>;
+ };
+
+ /* USB-A host 5 V (through the hub), gated by GPIO4 PB0. */
+ vcc_5v0_usbhost: regulator-vcc-5v0-usbhost {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpios = <&gpio4 RK_PB0 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usb_host_pwren>;
+ regulator-name = "vcc_5v0_usbhost";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ vin-supply = <&vcc_5v0_device>;
+ };
+};
+
+/*
+ * ComboPHY0 -> PCIe lane (M.2 slot); ComboPHY1 -> USB3 lane (USB-A hub).
+ */
+&combphy0_ps {
+ status = "okay";
+};
+
+&combphy1_psu {
+ status = "okay";
+};
+
+&hdmi {
+ status = "okay";
+};
+
+&hdmi_in {
+ hdmi_in_vp0: endpoint {
+ remote-endpoint = <&vp0_out_hdmi>;
+ };
+};
+
+&hdmi_out {
+ hdmi_out_con: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+};
+
+&hdmi_sound {
+ status = "okay";
+};
+
+&hdptxphy {
+ status = "okay";
+};
+
+/* SAI6 is the I2S CPU DAI feeding the HDMI audio path. */
+&sai6 {
+ status = "okay";
+};
+
+/* I2C0: FUSB302 USB-C PD controller @ 0x22, pinctrl i2c0m1 (PC4/PC5). */
+&i2c0 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0m1_xfer>;
+
+ usbc0: usb-typec@22 {
+ compatible = "fcs,fusb302";
+ reg = <0x22>;
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PB4 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&usbc0_int>;
+ vbus-supply = <&vcc_5v0_typec0>;
+
+ usb_con: connector {
+ compatible = "usb-c-connector";
+ label = "USB-C";
+ data-role = "dual";
+ power-role = "dual";
+ try-power-role = "sink";
+ op-sink-microwatt = <1000000>;
+ sink-pdos =
+ <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)
+ PDO_FIXED(9000, 3000, PDO_FIXED_USB_COMM)
+ PDO_FIXED(12000, 3000, PDO_FIXED_USB_COMM)>;
+ source-pdos =
+ <PDO_FIXED(5000, 3000, PDO_FIXED_USB_COMM)>;
+
+ altmodes {
+ displayport {
+ svid = /bits/ 16 <0xff01>;
+ vdo = <0xffffffff>;
+ };
+ };
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+ usbc0_orien_sw: endpoint {
+ remote-endpoint = <&usbdp_phy_orientation_switch>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+ usbc0_role_sw: endpoint {
+ remote-endpoint = <&usb_drd0_role_switch>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+ dp_altmode_mux: endpoint {
+ remote-endpoint = <&usbdp_phy_dp_altmode_mux>;
+ };
+ };
+ };
+ };
+ };
+};
+
+/*
+ * PCIe 2.0 x1 M.2 slot. Reset GPIO2 PB1, power vcc_3v3_pcie (GPIO0 PC3).
+ */
+&pcie0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pcie_reset>;
+ reset-gpios = <&gpio2 RK_PB1 GPIO_ACTIVE_HIGH>;
+ vpcie3v3-supply = <&vcc_3v3_pcie>;
+ status = "okay";
+};
+
+/* microSD card slot. */
+&sdmmc {
+ bus-width = <4>;
+ cap-mmc-highspeed;
+ cap-sd-highspeed;
+ disable-wp;
+ max-frequency = <200000000>;
+ no-sdio;
+ no-mmc;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vccio_sd_s0>;
+ status = "okay";
+};
+
+&u2phy0 {
+ status = "okay";
+};
+
+&u2phy0_otg {
+ phy-supply = <&vcc_5v0_typec0>;
+ status = "okay";
+};
+
+&u2phy1 {
+ status = "okay";
+};
+
+&u2phy1_otg {
+ phy-supply = <&vcc_5v0_usbhost>;
+ status = "okay";
+};
+
+/* Debug UART0 on the 40-pin header. */
+&uart0 {
+ pinctrl-0 = <&uart0m0_xfer>;
+ status = "okay";
+};
+
+/* USB DRD0: USB-C (USBDP SuperSpeed + USB2 HS), OTG with FUSB302 role-switch. */
+&usb_drd0_dwc3 {
+ dr_mode = "otg";
+ usb-role-switch;
+ status = "okay";
+
+ port {
+ usb_drd0_role_switch: endpoint {
+ remote-endpoint = <&usbc0_role_sw>;
+ };
+ };
+};
+
+/* USB DRD1: USB-A ports behind the hub (combphy1 SuperSpeed + USB2 HS). */
+&usb_drd1_dwc3 {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbdp_phy {
+ status = "okay";
+ mode-switch;
+ orientation-switch;
+ sbu1-dc-gpios = <&gpio4 RK_PC4 GPIO_ACTIVE_HIGH>;
+ sbu2-dc-gpios = <&gpio4 RK_PC5 GPIO_ACTIVE_HIGH>;
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ usbdp_phy_orientation_switch: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&usbc0_orien_sw>;
+ };
+
+ usbdp_phy_dp_altmode_mux: endpoint@1 {
+ reg = <1>;
+ remote-endpoint = <&dp_altmode_mux>;
+ };
+ };
+};
+
+&vop {
+ status = "okay";
+};
+
+&vop_mmu {
+ status = "okay";
+};
+
+&vp0 {
+ vp0_out_hdmi: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+ reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+ remote-endpoint = <&hdmi_in_vp0>;
+ };
+};
+
+&pinctrl {
+ leds {
+ /* GPIO2 PD0 - green carrier LED */
+ led_green_en: led-green-en {
+ rockchip,pins = <2 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ /* GPIO2 PD1 - red carrier LED */
+ led_red_en: led-red-en {
+ rockchip,pins = <2 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pcie {
+ /* GPIO0 PC3 - PCIe power enable */
+ pcie_pwr_en: pcie-pwr-en {
+ rockchip,pins = <0 RK_PC3 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ /* GPIO2 PB1 - PCIe PERST# */
+ pcie_reset: pcie-reset {
+ rockchip,pins = <2 RK_PB1 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ usb {
+ /* GPIO4 PB0 - USB host 5V enable */
+ usb_host_pwren: usb-host-pwren {
+ rockchip,pins = <4 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ /* GPIO2 PB6 - USB OTG / Type-C 5V enable */
+ usb_otg0_pwren: usb-otg0-pwren {
+ rockchip,pins = <2 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ /* GPIO0 PB4 - FUSB302 INT# (active-low) */
+ usbc0_int: usbc0-int {
+ rockchip,pins = <0 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi
new file mode 100644
index 000000000..91d7918c2
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5.dtsi
@@ -0,0 +1,558 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * ArmSoM CM5 - Rockchip RK3576 compute module (Raspberry Pi CM4 form factor).
+ *
+ * Common to all CM5 carriers. The carrier .dts includes this file, sets the
+ * board model/compatible, and adds carrier-specific peripherals.
+ *
+ * On-module devices:
+ * - RK806 PMIC on I2C1
+ * - HYM8563 RTC on I2C2
+ * - eMMC (SDHCI)
+ * - GMAC0 + MotorComm YT8531 Gigabit Ethernet PHY (RGMII)
+ * - SYN43752 WiFi 6 + BT 5.x (SDIO + UART4)
+ *
+ * Copyright (c) 2024 ArmSoM
+ * Copyright (c) 2026 Jiaxing Hu <gahing@gahingwoo.com>
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pinctrl/rockchip.h>
+#include "rk3576.dtsi"
+
+/ {
+ compatible = "armsom,cm5", "rockchip,rk3576";
+
+ vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v1_nldo_s3";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <1100000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ vcc_1v2_ufs_vccq_s0: regulator-vcc-1v2-ufs-vccq-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v2_ufs_vccq_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ vcc_1v8_s0: regulator-vcc-1v8-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8_s3>;
+ };
+
+ vcc_1v8_ufs_vccq2_s0: regulator-vcc-1v8-ufs-vccq2-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_1v8_ufs_vccq2_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ vin-supply = <&vcc_1v8_s3>;
+ };
+
+ vcc_2v0_pldo_s3: regulator-vcc-2v0-pldo-s3 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_2v0_pldo_s3";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <2000000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ vcc_3v3_s0: regulator-vcc-3v3-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_3v3_s3>;
+ };
+
+ vcc_3v3_ufs_s0: regulator-vcc-ufs-s0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_3v3_ufs_s0";
+ regulator-boot-on;
+ regulator-always-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ vin-supply = <&vcc_5v0_sys>;
+ };
+
+ /*
+ * WiFi power sequencer for SYN43752. Reset GPIO1 PC6 active-low,
+ * clock from the HYM8563 RTC oscillator.
+ */
+ sdio_pwrseq: sdio-pwrseq {
+ compatible = "mmc-pwrseq-simple";
+ clocks = <&hym8563>;
+ clock-names = "ext_clock";
+ pinctrl-names = "default";
+ pinctrl-0 = <&wifi_reg_on>;
+ reset-gpios = <&gpio1 RK_PC6 GPIO_ACTIVE_LOW>;
+ };
+};
+
+&cpu_b0 {
+ cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b1 {
+ cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b2 {
+ cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_b3 {
+ cpu-supply = <&vdd_cpu_big_s0>;
+};
+
+&cpu_l0 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+ cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+/*
+ * GMAC0 drives an on-module MotorComm YT8531. The PHY has no local crystal, so
+ * it relies on the SoC 25 MHz reference: clk_mac_refout (REFCLKO25M_GMAC0_OUT)
+ * has to be named on the gmac node for dwmac-rk to enable it, and
+ * ethm0_clk0_25m_out routes it to the pad.
+ */
+&gmac0 {
+ phy-mode = "rgmii-id";
+ clock_in_out = "output";
+ clocks = <&cru CLK_GMAC0_125M_SRC>, <&cru CLK_GMAC0_RMII_CRU>,
+ <&cru PCLK_GMAC0>, <&cru ACLK_GMAC0>,
+ <&cru CLK_GMAC0_PTP_REF>, <&cru REFCLKO25M_GMAC0_OUT>;
+ clock-names = "stmmaceth", "clk_mac_ref", "pclk_mac", "aclk_mac",
+ "ptp_ref", "clk_mac_refout";
+ phy-handle = <&rgmii_phy0>;
+ phy-supply = <&vcc_3v3_s3>;
+ pinctrl-names = "default";
+ pinctrl-0 = <ð0m0_miim
+ ð0m0_tx_bus2
+ ð0m0_rx_bus2
+ ð0m0_rgmii_clk
+ ð0m0_rgmii_bus
+ ðm0_clk0_25m_out>;
+ status = "okay";
+};
+
+&gpu {
+ mali-supply = <&vdd_gpu_s0>;
+ status = "okay";
+};
+
+/* I2C1: RK806 PMIC @ 0x23 (interrupt on GPIO0 PA6). */
+&i2c1 {
+ status = "okay";
+
+ pmic@23 {
+ compatible = "rockchip,rk806";
+ reg = <0x23>;
+
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA6 IRQ_TYPE_LEVEL_LOW>;
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+ <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+
+ system-power-controller;
+
+ vcc1-supply = <&vcc_5v0_sys>;
+ vcc2-supply = <&vcc_5v0_sys>;
+ vcc3-supply = <&vcc_5v0_sys>;
+ vcc4-supply = <&vcc_5v0_sys>;
+ vcc5-supply = <&vcc_5v0_sys>;
+ vcc6-supply = <&vcc_5v0_sys>;
+ vcc7-supply = <&vcc_5v0_sys>;
+ vcc8-supply = <&vcc_5v0_sys>;
+ vcc9-supply = <&vcc_5v0_sys>;
+ vcc10-supply = <&vcc_5v0_sys>;
+ vcc11-supply = <&vcc_2v0_pldo_s3>;
+ vcc12-supply = <&vcc_5v0_sys>;
+ vcc13-supply = <&vcc_1v1_nldo_s3>;
+ vcc14-supply = <&vcc_1v1_nldo_s3>;
+ vcca-supply = <&vcc_5v0_sys>;
+
+ gpio-controller;
+ #gpio-cells = <2>;
+
+ rk806_dvs1_null: dvs1-null-pins {
+ pins = "gpio_pwrctrl1";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs2_null: dvs2-null-pins {
+ pins = "gpio_pwrctrl2";
+ function = "pin_fun0";
+ };
+
+ rk806_dvs3_null: dvs3-null-pins {
+ pins = "gpio_pwrctrl3";
+ function = "pin_fun0";
+ };
+
+ regulators {
+ vdd_cpu_big_s0: dcdc-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_cpu_big_s0";
+ regulator-enable-ramp-delay = <400>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_npu_s0: dcdc-reg2 {
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_npu_s0";
+ regulator-enable-ramp-delay = <400>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_cpu_lit_s0: dcdc-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <950000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_cpu_lit_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vcc_3v3_s3: dcdc-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcc_3v3_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vdd_gpu_s0: dcdc-reg5 {
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <900000>;
+ regulator-ramp-delay = <12500>;
+ regulator-name = "vdd_gpu_s0";
+ regulator-enable-ramp-delay = <400>;
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ regulator-suspend-microvolt = <850000>;
+ };
+ };
+
+ vddq_ddr_s0: dcdc-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vddq_ddr_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdd_logic_s0: dcdc-reg7 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <800000>;
+ regulator-name = "vdd_logic_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcc_1v8_s3: dcdc-reg8 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcc_1v8_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd2_ddr_s3: dcdc-reg9 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-name = "vdd2_ddr_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vdd_ddr_s0: dcdc-reg10 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <550000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdd_ddr_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca_1v8_s0: pldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca_1v8_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pldo2_s0: pldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pldo2_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_1v2_s0: pldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-name = "vdda_1v2_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca_3v3_s0: pldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vcca_3v3_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vccio_sd_s0: pldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-name = "vccio_sd_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vcca1v8_pldo6_s3: pldo-reg6 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-name = "vcca1v8_pldo6_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_0v75_s3: nldo-reg1 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdd_0v75_s3";
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <750000>;
+ };
+ };
+
+ vdda_ddr_pll_s0: nldo-reg2 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdda_ddr_pll_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda0v75_hdmi_s0: nldo-reg3 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <837500>;
+ regulator-max-microvolt = <837500>;
+ regulator-name = "vdda0v75_hdmi_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v85_s0: nldo-reg4 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <850000>;
+ regulator-name = "vdda_0v85_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+
+ vdda_0v75_s0: nldo-reg5 {
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <750000>;
+ regulator-max-microvolt = <750000>;
+ regulator-name = "vdda_0v75_s0";
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
+ };
+ };
+ };
+};
+
+/* I2C2: HYM8563 RTC @ 0x51 (interrupt on GPIO0 PA0). */
+&i2c2 {
+ status = "okay";
+
+ hym8563: rtc@51 {
+ compatible = "haoyu,hym8563";
+ reg = <0x51>;
+ clock-output-names = "hym8563";
+ interrupt-parent = <&gpio0>;
+ interrupts = <RK_PA0 IRQ_TYPE_LEVEL_LOW>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&hym8563_int>;
+ wakeup-source;
+ #clock-cells = <0>;
+ };
+};
+
+/*
+ * The PHY reset has to be described at the MDIO bus level: mdiobus releases a
+ * bus level reset before it scans for PHY IDs, whereas the per-PHY reset-gpios
+ * is only applied by phylib once the PHY has already been found, which never
+ * happens while the YT8531 is still held in reset.
+ */
+&mdio0 {
+ reset-gpios = <&gpio2 RK_PB3 GPIO_ACTIVE_LOW>;
+ reset-delay-us = <20000>;
+ reset-post-delay-us = <100000>;
+
+ rgmii_phy0: phy@1 {
+ compatible = "ethernet-phy-ieee802.3-c22";
+ reg = <0x1>;
+ };
+};
+
+&saradc {
+ vref-supply = <&vcca_1v8_s0>;
+ status = "okay";
+};
+
+/* eMMC: on-module, HS400 200 MHz with enhanced strobe. */
+&sdhci {
+ bus-width = <8>;
+ full-pwr-cycle-in-suspend;
+ max-frequency = <200000000>;
+ mmc-hs400-1_8v;
+ mmc-hs400-enhanced-strobe;
+ no-sdio;
+ no-sd;
+ non-removable;
+ /delete-property/ supports-cqe;
+ status = "okay";
+};
+
+/* SDIO: SYN43752 WiFi, power-sequenced by sdio_pwrseq, clock from HYM8563. */
+&sdio {
+ bus-width = <4>;
+ cap-sdio-irq;
+ disable-wp;
+ keep-power-in-suspend;
+ mmc-pwrseq = <&sdio_pwrseq>;
+ no-sd;
+ no-mmc;
+ non-removable;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ vmmc-supply = <&vcc_3v3_s3>;
+ vqmmc-supply = <&vcc_1v8_s3>;
+ wakeup-source;
+ status = "okay";
+};
+
+/* UART4: Bluetooth (SYN43752). */
+&uart4 {
+ pinctrl-0 = <&uart4m1_xfer &uart4m1_ctsn &uart4m1_rtsn>;
+ pinctrl-names = "default";
+ uart-has-rtscts;
+ status = "okay";
+};
+
+&pinctrl {
+ hym8563 {
+ hym8563_int: hym8563-int {
+ rockchip,pins = <0 RK_PA0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+
+ wireless-wlan {
+ /* GPIO1 PC6 - WiFi power enable / reset (sdio_pwrseq) */
+ wifi_reg_on: wifi-reg-on {
+ rockchip,pins = <1 RK_PC6 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
--
2.43.0
^ permalink raw reply related [flat|nested] 3+ messages in thread