From: Long Zhao <longzhao@ambarella.com>
To: Arnd Bergmann <arnd@arndb.de>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
<linux-arm-kernel@lists.infradead.org>, <soc@lists.linux.dev>
Cc: Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>, <devicetree@vger.kernel.org>,
"Michael Turquette" <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>, <linux-clk@vger.kernel.org>,
Linus Walleij <linusw@kernel.org>, <linux-gpio@vger.kernel.org>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Jiri Slaby <jirislaby@kernel.org>, <linux-serial@vger.kernel.org>,
Catalin Marinas <catalin.marinas@arm.com>,
Will Deacon <will@kernel.org>, <linux-kernel@vger.kernel.org>,
Long Zhao <longzhao@ambarella.com>
Subject: [PATCH 09/10] arm64: ambarella: add ARCH_AMBARELLA and CV75 EVK DT
Date: Thu, 30 Jul 2026 18:43:29 +0800 [thread overview]
Message-ID: <20260730104330.81367-10-longzhao@ambarella.com> (raw)
In-Reply-To: <20260730104330.81367-1-longzhao@ambarella.com>
Enable the Ambarella ARMv8 platform Kconfig, add the CV75 SoC and
EVK device trees, and select the Ambarella UART in the arm64
defconfig for console bring-up.
Signed-off-by: Long Zhao <longzhao@ambarella.com>
---
arch/arm64/Kconfig.platforms | 9 ++
arch/arm64/boot/dts/Makefile | 1 +
arch/arm64/boot/dts/ambarella/Makefile | 3 +
arch/arm64/boot/dts/ambarella/cv75-evk.dts | 30 ++++
arch/arm64/boot/dts/ambarella/cv75.dtsi | 151 +++++++++++++++++++++
arch/arm64/configs/defconfig | 3 +
6 files changed, 197 insertions(+)
create mode 100644 arch/arm64/boot/dts/ambarella/Makefile
create mode 100644 arch/arm64/boot/dts/ambarella/cv75-evk.dts
create mode 100644 arch/arm64/boot/dts/ambarella/cv75.dtsi
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index d2acfac73003..166430ddb3c9 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -26,6 +26,15 @@ config ARCH_SUNXI
help
This enables support for Allwinner sunxi based SoCs like the A64.
+config ARCH_AMBARELLA
+ bool "Ambarella SoC family"
+ select ARM_PSCI
+ select HAVE_ARM_ARCH_TIMER
+ select PINCTRL
+ select PINCTRL_AMB
+ help
+ This enables support for the ARM64 based Ambarella SoCs like CV75.
+
config ARCH_ALPINE
bool "Annapurna Labs Alpine platform"
select ALPINE_MSI if PCI
diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
index fc726b215f12..f1709eb5d915 100644
--- a/arch/arm64/boot/dts/Makefile
+++ b/arch/arm64/boot/dts/Makefile
@@ -4,6 +4,7 @@ subdir-y += airoha
subdir-y += allwinner
subdir-y += altera
subdir-y += amazon
+subdir-y += ambarella
subdir-y += amd
subdir-y += amlogic
subdir-y += apm
diff --git a/arch/arm64/boot/dts/ambarella/Makefile b/arch/arm64/boot/dts/ambarella/Makefile
new file mode 100644
index 000000000000..ddca3d7b18cc
--- /dev/null
+++ b/arch/arm64/boot/dts/ambarella/Makefile
@@ -0,0 +1,3 @@
+# SPDX-License-Identifier: GPL-2.0
+
+dtb-$(CONFIG_ARCH_AMBARELLA) += cv75-evk.dtb
diff --git a/arch/arm64/boot/dts/ambarella/cv75-evk.dts b/arch/arm64/boot/dts/ambarella/cv75-evk.dts
new file mode 100644
index 000000000000..42a0fe24b83b
--- /dev/null
+++ b/arch/arm64/boot/dts/ambarella/cv75-evk.dts
@@ -0,0 +1,30 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Ambarella CV75 EVK board
+ */
+
+/dts-v1/;
+
+#include "cv75.dtsi"
+
+/ {
+ model = "Ambarella CV75 EVK Board";
+ compatible = "ambarella,cv75-evk", "ambarella,cv75";
+
+ aliases {
+ serial0 = &uart0;
+ };
+
+ chosen {
+ stdout-path = &uart0;
+ };
+
+ memory@200000 {
+ device_type = "memory";
+ reg = <0x0 0x00200000 0x0 0x07e00000>;
+ };
+};
+
+&uart0 {
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/ambarella/cv75.dtsi b/arch/arm64/boot/dts/ambarella/cv75.dtsi
new file mode 100644
index 000000000000..7c6a61f473ef
--- /dev/null
+++ b/arch/arm64/boot/dts/ambarella/cv75.dtsi
@@ -0,0 +1,151 @@
+// SPDX-License-Identifier: GPL-2.0-or-later
+/*
+ * Ambarella CV75 SoC
+ *
+ * Boot peripheral: UART0 console.
+ * Clocks: a single ambarella,cv75-rct provider.
+ */
+
+#include <dt-bindings/clock/ambarella,cv75-clock.h>
+#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/pinctrl/ambarella,pinctrl.h>
+
+/ {
+ compatible = "ambarella,cv75";
+ interrupt-parent = <&gic>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+
+ osc: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-output-names = "osc";
+ clock-frequency = <24000000>;
+ };
+
+ psci {
+ compatible = "arm,psci-0.2";
+ method = "smc";
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu@0 {
+ compatible = "arm,cortex-a76";
+ device_type = "cpu";
+ reg = <0x000>;
+ enable-method = "psci";
+ };
+
+ cpu@1 {
+ compatible = "arm,cortex-a76";
+ device_type = "cpu";
+ reg = <0x100>;
+ enable-method = "psci";
+ };
+ };
+
+ gic: interrupt-controller@fff0100000 {
+ compatible = "arm,gic-400";
+ #interrupt-cells = <3>;
+ #address-cells = <0>;
+ #size-cells = <1>;
+ interrupt-controller;
+ reg = <0xff 0xf0101000 0x0 0x1000>,
+ <0xff 0xf0102000 0x0 0x2000>,
+ <0xff 0xf0104000 0x0 0x2000>,
+ <0xff 0xf0106000 0x0 0x2000>;
+ interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_HIGH)>;
+ };
+
+ timer {
+ compatible = "arm,armv8-timer";
+ interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>,
+ <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(2) | IRQ_TYPE_LEVEL_LOW)>;
+ };
+
+ soc {
+ compatible = "simple-bus";
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+
+ /* Clock provider and shared system registers. */
+ rct: clock-controller@ffed080000 {
+ compatible = "ambarella,cv75-rct", "syscon";
+ reg = <0xff 0xed080000 0x0 0x1000>;
+ clocks = <&osc>;
+ clock-names = "osc";
+ #clock-cells = <1>;
+
+ assigned-clocks = <&rct CV75_GCLK_UART0>;
+ assigned-clock-parents = <&osc>;
+ assigned-clock-rates = <24000000>;
+ };
+
+ apb@ffe4000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xff 0xe4000000 0x0 0x01000000>;
+ ranges = <0xe4000000 0xff 0xe4000000 0x01000000>;
+
+ uart0: serial@e4000000 {
+ compatible = "ambarella,cv75-uart", "ambarella,uart";
+ reg = <0xe4000000 0x1000>;
+ interrupts = <GIC_SPI 170 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&rct CV75_GCLK_UART0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart0_pins>;
+ status = "disabled";
+ };
+
+ pinctrl: pinctrl@e4013000 {
+ compatible = "ambarella,cv75-pinctrl";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <0xe4013000 0x1000>, <0xe4014000 0x1000>,
+ <0xe4015000 0x1000>, <0xe4010000 0x1000>;
+ reg-names = "gpio0", "gpio1", "gpio2", "iomux";
+ interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 164 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 165 IRQ_TYPE_LEVEL_HIGH>;
+ ambarella,drive-strength-syscon = <&rct>;
+ ambarella,pull-syscon = <&s_scratchpad_syscon>;
+
+ gpio: gpio@0 {
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ gpio-ranges = <&pinctrl 0 0 95>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+ };
+
+ uart0_pins: uart0-pins {
+ function = "uart0";
+ pinmux = <AMBA_PINMUX(44, 1)>,
+ <AMBA_PINMUX(45, 1)>;
+ };
+ };
+ };
+
+ ahb@ffe0000000 {
+ compatible = "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0xff 0xe0000000 0x0 0x01000000>;
+ ranges = <0xe0000000 0xff 0xe0000000 0x01000000>;
+
+ s_scratchpad_syscon: scratchpad@e002e000 {
+ compatible = "ambarella,cv75-sec-scratchpad",
+ "ambarella,sec-scratchpad", "syscon";
+ reg = <0xe002e000 0x1000>;
+ };
+ };
+ };
+};
diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index ad3bd3d9507b..64e8fbe43d27 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -36,6 +36,7 @@ CONFIG_CRASH_DUMP=y
CONFIG_ARCH_ACTIONS=y
CONFIG_ARCH_AIROHA=y
CONFIG_ARCH_SUNXI=y
+CONFIG_ARCH_AMBARELLA=y
CONFIG_ARCH_ALPINE=y
CONFIG_ARCH_APPLE=y
CONFIG_ARCH_ARTPEC=y
@@ -567,6 +568,8 @@ CONFIG_SERIAL_8250_OMAP=y
CONFIG_SERIAL_8250_MT6577=y
CONFIG_SERIAL_8250_UNIPHIER=y
CONFIG_SERIAL_OF_PLATFORM=y
+CONFIG_SERIAL_AMBARELLA=y
+CONFIG_SERIAL_AMBARELLA_CONSOLE=y
CONFIG_SERIAL_AMBA_PL011=y
CONFIG_SERIAL_AMBA_PL011_CONSOLE=y
CONFIG_SERIAL_MESON=y
--
2.34.1
NOTE: This email (including attachments) contain Ambarella Proprietary and/or Confidential Information and is intended solely for the use of the individual(s) to whom it is addressed. Any unauthorized review, use, disclosure, distribute, copy, or print is prohibited. If you are not an intended recipient, please contact the sender by reply email and destroy all copies of the original message. Thank you.
next prev parent reply other threads:[~2026-07-30 10:44 UTC|newest]
Thread overview: 21+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-07-30 10:43 [PATCH 00/10] Ambarella CV75 SoC minimal bring-up Long Zhao
2026-07-30 10:43 ` [PATCH 01/10] dt-bindings: arm: add Ambarella CV75 platforms Long Zhao
2026-07-30 10:43 ` [PATCH 02/10] dt-bindings: soc: add Ambarella secure scratchpad Long Zhao
2026-07-30 10:43 ` [PATCH 03/10] dt-bindings: clock: add Ambarella CV75 RCT clock controller Long Zhao
2026-07-30 12:42 ` Rob Herring (Arm)
2026-07-30 14:11 ` Rob Herring
2026-07-30 10:43 ` [PATCH 04/10] dt-bindings: pinctrl: add Ambarella CV75 pinctrl Long Zhao
2026-07-30 12:42 ` Rob Herring (Arm)
2026-07-30 14:21 ` Rob Herring
2026-07-30 10:43 ` [PATCH 05/10] dt-bindings: serial: add Ambarella UART Long Zhao
2026-07-30 10:49 ` Krzysztof Kozlowski
2026-07-30 10:43 ` [PATCH 06/10] clk: ambarella: add CV75 CCU driver Long Zhao
2026-07-30 10:43 ` [PATCH 07/10] pinctrl: ambarella: add Ambarella pin controller Long Zhao
2026-07-30 10:43 ` [PATCH 08/10] serial: ambarella: add Ambarella UART driver Long Zhao
2026-07-30 10:54 ` Greg Kroah-Hartman
2026-07-30 10:43 ` Long Zhao [this message]
2026-07-30 12:18 ` [PATCH 09/10] arm64: ambarella: add ARCH_AMBARELLA and CV75 EVK DT Marc Zyngier
2026-07-30 10:43 ` [PATCH 10/10] MAINTAINERS: add ARM/AMBARELLA SoC support Long Zhao
2026-07-30 10:48 ` [PATCH 00/10] Ambarella CV75 SoC minimal bring-up Krzysztof Kozlowski
2026-07-30 11:05 ` [EXT] " Long Zhao
2026-07-30 11:56 ` Alexandre Belloni
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260730104330.81367-10-longzhao@ambarella.com \
--to=longzhao@ambarella.com \
--cc=alexandre.belloni@bootlin.com \
--cc=arnd@arndb.de \
--cc=catalin.marinas@arm.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=jirislaby@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linusw@kernel.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-serial@vger.kernel.org \
--cc=mturquette@baylibre.com \
--cc=robh@kernel.org \
--cc=sboyd@kernel.org \
--cc=soc@lists.linux.dev \
--cc=will@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox