[PATCH v6 00/12] arm64: dts: rockchip: Add NanoPi M6 board

[PATCH v6 00/12] arm64: dts: rockchip: Add NanoPi M6 board

[Joachim Eastwood via B4 Relay]

This patch series add support for the NanoPi M6. This board is very
similar to the NanoPi R6C and R6S boards which are already supported.

Main differences:
* M.2 M-key slot with PCIe (Also present on R6C)
* M.2 E-key slot with PCIe and USB (from hub)
* 1 additional USB 2.0 port from an on-board USB hub
* RT5616 audio CODEC

Patch 1 documents the NanoPi M6 board compatibility string
Patch 2 to 10 are fixes and additions to the nanopi-r6 base DT
Patch 11 extracts the common NanoPi 6 series bits from nanopi-r6 into
nanopi.dtsi
The final patch adds support for NanoPi M6. Support for M6 has been
split into two files; one dtsi and one dts file. This makes it easier
to add support to the new M6V2 board at a later stage.

All changes have been verified using the schematics for M6, R6C and R6S.
Only M6 have been boot and runtime tested. Testers for R6x are welcome.

Note that Sashiko may complain that u2phy0_otg is a dangling phandle in
patch 11. This will never happen in practice so it's safe to ignore.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
Changes in v6:
- Rebase on v7.3-rc1
- Link to v5: https://patch.msgid.link/20260728-nanopi-m6-v5-0-cbc1eb0d8d56@gmail.com

Changes in v5:
- Switch from simple-audio-card to audio-graph-card as Sashiko
  complains, rightfully, that the bindings are a mismash of both.
- Add pull-up on sd cd pin. Noticed by Diederik.
- Link to v4: https://patch.msgid.link/20260717-nanopi-m6-v4-0-b31391a72e41@gmail.com

Changes in v4:
- Remove boot-on reintroduction on vdd_npu_s0 in nanopi.dtsi during
  refactor screw-up. Thanks to Sashiko for catching that.
- Fix minor typo in "add gmac1 add phy-supply" commit message
- Use schematic net names on PCIe reset lines. As suggested by Diederik.
- Link to v3: https://patch.msgid.link/20260713-nanopi-m6-v3-0-227567ffc5dc@gmail.com

Changes in v3:
- Reorder patches so the DT fixes/additions are applied to
  nanopi-r6.dtsi as suggested by Jonas Karlman
- Add comment to gmac to rgmii-rxid phy-mode to explain usage
- Addition of pinctrl to sd and pcie are now marked as fixes
- Remove both always-on and boot-on from NPU regulator
- Link to v2: https://patch.msgid.link/20260711-nanopi-m6-v2-0-422675a65402@gmail.com

Changes in v2:
- Organize DT such that adding support to NanoPi M6V2 later is easier
- Use correct clk id for I2C mclk out as suggested by Diederik.
- Add a couple of acks from Krzysztof Kozlowski.
- Link to v1: https://patch.msgid.link/20260703-nanopi-m6-v1-0-8344a1559519@gmail.com

---
Joachim Eastwood (12):
      dt-bindings: arm: rockchip: add FriendlyElec NanoPi M6
      arm64: dts: rockchip: rk3588s-nanopi-r6: fix missing sdmmc cd pinctrl
      arm64: dts: rockchip: rk3588s-nanopi-r6: fix missing pcie rst pinctrl
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove pull up on rtc int pin
      arm64: dts: rockchip: rk3588s-nanopi-r6: pcie2x1l2: add clkreq
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove always-on and boot-on from vdd_npu_s0 reg
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove useless vcc_3v3_pcie20
      arm64: dts: rockchip: rk3588s-nanopi-r6: add gmac1 phy-supply
      arm64: dts: rockchip: rk3588s-nanopi-r6: remove bogus vcc5v0_usb regulator
      arm64: dts: rockchip: rk3588s-nanopi-r6: add comment about gmac phy-mode
      arm64: dts: rockchip: rk3588s-nanopi-r6: refactor to support M6 boards
      arm64: dts: rockchip: add support for NanoPi M6 board

 .../devicetree/bindings/arm/rockchip.yaml          |   3 +-
 arch/arm64/boot/dts/rockchip/Makefile              |   1 +
 .../arm64/boot/dts/rockchip/rk3588s-nanopi-m6.dtsi | 142 ++++
 .../boot/dts/rockchip/rk3588s-nanopi-m6v1.dts      |  57 ++
 .../arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 792 +-------------------
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi.dtsi   | 797 +++++++++++++++++++++
 6 files changed, 1000 insertions(+), 792 deletions(-)
---
base-commit: cee9395acd8043be0644b25c34bfa86623f2b935
change-id: 20260701-nanopi-m6-ffeef7252fd7

Best regards,
--  
Joachim Eastwood <joachim.eastwood@gmail.com>

[PATCH v6 01/12] dt-bindings: arm: rockchip: add FriendlyElec NanoPi M6

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

Add device tree binding documentation for FriendlyElec NanoPi M6,
a single-board computer based on the Rockchip RK3588S SoC. Very
similar to NanoPi R6C and R6S.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 Documentation/devicetree/bindings/arm/rockchip.yaml | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/arm/rockchip.yaml b/Documentation/devicetree/bindings/arm/rockchip.yaml
index a799bb843f74..d8cf33f76090 100644
--- a/Documentation/devicetree/bindings/arm/rockchip.yaml
+++ b/Documentation/devicetree/bindings/arm/rockchip.yaml
@@ -369,9 +369,10 @@ properties:
               - friendlyarm,nanopi-r5s
           - const: rockchip,rk3568
 
-      - description: FriendlyElec NanoPi R6 series boards
+      - description: FriendlyElec NanoPi6 series boards
         items:
           - enum:
+              - friendlyarm,nanopi-m6
               - friendlyarm,nanopi-r6c
               - friendlyarm,nanopi-r6s
           - const: rockchip,rk3588s

-- 
2.55.0

[PATCH v6 02/12] arm64: dts: rockchip: rk3588s-nanopi-r6: fix missing sdmmc cd pinctrl

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

The cd (card detect) pin is used, but not reserved through pinctrl.

Fixes: 95147bb42bc1 ("arm64: dts: rockchip: Fix the SD card detection on NanoPi R6C/R6S")
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 91b6eefd7abf..3ee6853b8752 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -421,6 +421,10 @@ rtc_int: rtc-int {
 	};
 
 	sdmmc {
+		sdmmc_det_pin: sdmmc-det-pin {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
 		sd_s0_pwr: sd-s0-pwr {
 			rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
 		};
@@ -496,6 +500,8 @@ &sdmmc {
 	no-mmc;
 	no-sdio;
 	sd-uhs-sdr104;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det_pin>;
 	vmmc-supply = <&vcc_3v3_sd_s0>;
 	vqmmc-supply = <&vccio_sd_s0>;
 	status = "okay";

-- 
2.55.0

[PATCH v6 03/12] arm64: dts: rockchip: rk3588s-nanopi-r6: fix missing pcie rst pinctrl

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

The pins are used as reset-gpios but not reserved through pinctrl.

Fixes: f3c6526d6fb2 ("arm64: dts: rockchip: Convert dts files used as parents to dtsi files")
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 3ee6853b8752..5bbd5d2fc5fa 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -360,12 +360,16 @@ rgmii_phy1: ethernet-phy@1 {
 };
 
 &pcie2x1l1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_1_perstn_m2>;
 	reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
 	vpcie3v3-supply = <&vcc_3v3_pcie20>;
 	status = "okay";
 };
 
 &pcie2x1l2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_2_perstn_m0>;
 	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
 	vpcie3v3-supply = <&vcc_3v3_pcie20>;
 	status = "okay";
@@ -420,6 +424,16 @@ rtc_int: rtc-int {
 		};
 	};
 
+	pcie {
+		pcie20x1_1_perstn_m2: pcie20x1-1-perstn-m2 {
+			rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie20x1_2_perstn_m0: pcie20x1-2-perstn-m0 {
+			rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
 	sdmmc {
 		sdmmc_det_pin: sdmmc-det-pin {
 			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;

-- 
2.55.0

[PATCH v6 04/12] arm64: dts: rockchip: rk3588s-nanopi-r6: remove pull up on rtc int pin

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

All boards in the RK3588S NanoPi familiy has a pull on the PCB for the
RTC interrupt pin. So there is no need to enable the pull-up in the SoC.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 5bbd5d2fc5fa..f2b15e03d5ef 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -420,7 +420,7 @@ hdmi0_tx_on_h: hdmi0-tx-on-h {
 
 	hym8563 {
 		rtc_int: rtc-int {
-			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_up>;
+			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
 	};
 

-- 
2.55.0

[PATCH v6 05/12] arm64: dts: rockchip: rk3588s-nanopi-r6: pcie2x1l2: add clkreq

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

The clkreq is present on the board, so hook it up in DT.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index f2b15e03d5ef..b120dd98241f 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -369,7 +369,8 @@ &pcie2x1l1 {
 
 &pcie2x1l2 {
 	pinctrl-names = "default";
-	pinctrl-0 = <&pcie20x1_2_perstn_m0>;
+	pinctrl-0 = <&pcie20x1_2_perstn_m0>, <&pcie20x1m0_clkreqn>;
+	supports-clkreq;
 	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
 	vpcie3v3-supply = <&vcc_3v3_pcie20>;
 	status = "okay";

-- 
2.55.0

[PATCH v6 06/12] arm64: dts: rockchip: rk3588s-nanopi-r6: remove always-on and boot-on from vdd_npu_s0 reg

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

Since the NPU is hooked up in DT, the always-on and boot-on properties
on the regulator isn't needed anymore.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 2 --
 1 file changed, 2 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index b120dd98241f..8953dcebb93e 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -314,8 +314,6 @@ vdd_npu_s0: regulator@42 {
 		regulator-min-microvolt = <550000>;
 		regulator-max-microvolt = <950000>;
 		regulator-ramp-delay = <2300>;
-		regulator-boot-on;
-		regulator-always-on;
 		vin-supply = <&vcc5v0_sys>;
 
 		regulator-state-mem {

-- 
2.55.0

[PATCH v6 07/12] arm64: dts: rockchip: rk3588s-nanopi-r6: remove useless vcc_3v3_pcie20

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

There is no separate regulator for boards with RTL8125BG MACs.
The power is only separated from VCC_3V3_S3 with a ferrite bead.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 14 ++------------
 1 file changed, 2 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 8953dcebb93e..50af092f9cfa 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -131,16 +131,6 @@ vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
 		vin-supply = <&vcc_3v3_s3>;
 	};
 
-	vcc_3v3_pcie20: regulator-vcc3v3-pcie20 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc_3v3_pcie20";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		vin-supply = <&vcc_3v3_s3>;
-	};
-
 	vcc5v0_usb: regulator-vcc5v0-usb {
 		compatible = "regulator-fixed";
 		regulator-name = "vcc5v0_usb";
@@ -361,7 +351,7 @@ &pcie2x1l1 {
 	pinctrl-names = "default";
 	pinctrl-0 = <&pcie20x1_1_perstn_m2>;
 	reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc_3v3_pcie20>;
+	vpcie3v3-supply = <&vcc_3v3_s3>;
 	status = "okay";
 };
 
@@ -370,7 +360,7 @@ &pcie2x1l2 {
 	pinctrl-0 = <&pcie20x1_2_perstn_m0>, <&pcie20x1m0_clkreqn>;
 	supports-clkreq;
 	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc_3v3_pcie20>;
+	vpcie3v3-supply = <&vcc_3v3_s3>;
 	status = "okay";
 };
 

-- 
2.55.0

[PATCH v6 08/12] arm64: dts: rockchip: rk3588s-nanopi-r6: add gmac1 phy-supply

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

The RTL8211F Ethernet phy is powered from the VCC_3V3_S3 rail.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 50af092f9cfa..206cc88fdaa1 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -210,6 +210,7 @@ &gmac1 {
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy1>;
 	phy-mode = "rgmii-rxid";
+	phy-supply = <&vcc_3v3_s3>;
 	pinctrl-0 = <&gmac1_miim
 		     &gmac1_tx_bus2
 		     &gmac1_rx_bus2

-- 
2.55.0

[PATCH v6 09/12] arm64: dts: rockchip: rk3588s-nanopi-r6: remove bogus vcc5v0_usb regulator

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

All USB regulators (power switches) are feed from the main vcc5v0
supply. There is no regulator or switch in between.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 14 ++------------
 1 file changed, 2 insertions(+), 12 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 206cc88fdaa1..5a42e7dadc92 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -131,16 +131,6 @@ vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
 		vin-supply = <&vcc_3v3_s3>;
 	};
 
-	vcc5v0_usb: regulator-vcc5v0-usb {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_usb";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_sys>;
-	};
-
 	vcc5v0_usb_otg0: regulator-vcc5v0-usb-otg0 {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -150,7 +140,7 @@ vcc5v0_usb_otg0: regulator-vcc5v0-usb-otg0 {
 		regulator-name = "vcc5v0_usb_otg0";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_usb>;
+		vin-supply = <&vcc5v0_sys>;
 	};
 
 	vcc5v0_host_20: regulator-vcc5v0-host-20 {
@@ -162,7 +152,7 @@ vcc5v0_host_20: regulator-vcc5v0-host-20 {
 		regulator-name = "vcc5v0_host_20";
 		regulator-min-microvolt = <5000000>;
 		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_usb>;
+		vin-supply = <&vcc5v0_sys>;
 	};
 };
 

-- 
2.55.0

[PATCH v6 10/12] arm64: dts: rockchip: rk3588s-nanopi-r6: add comment about gmac phy-mode

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

Add comment to explain rgmii-rxid phy-mode usage. Note that the actual
delay in ns is not known. The tx_delay value of 0x42 comes from vendor
DT.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 5a42e7dadc92..94f218a48078 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -199,7 +199,7 @@ &cpu_l3 {
 &gmac1 {
 	clock_in_out = "output";
 	phy-handle = <&rgmii_phy1>;
-	phy-mode = "rgmii-rxid";
+	phy-mode = "rgmii-rxid"; /* Vendor provided tx delay value below */
 	phy-supply = <&vcc_3v3_s3>;
 	pinctrl-0 = <&gmac1_miim
 		     &gmac1_tx_bus2

-- 
2.55.0

[PATCH v6 11/12] arm64: dts: rockchip: rk3588s-nanopi-r6: refactor to support M6 boards

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

FriendlyElec NanoPi6 series consists of four distinct boards; R6S, R6C,
M6 and M6V2. Refactor FriendlyElec NanoPi R6 base dtsi in preparation
for adding NanoPi M6 support.

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 .../arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi | 792 +-------------------
 arch/arm64/boot/dts/rockchip/rk3588s-nanopi.dtsi   | 797 +++++++++++++++++++++
 2 files changed, 798 insertions(+), 791 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
index 94f218a48078..ac9eebd2b790 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-r6.dtsi
@@ -1,38 +1,8 @@
 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
 
-/dts-v1/;
-
-#include <dt-bindings/pinctrl/rockchip.h>
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/input/input.h>
-#include <dt-bindings/soc/rockchip,vop2.h>
-#include "rk3588s.dtsi"
+#include "rk3588s-nanopi.dtsi"
 
 / {
-	aliases {
-		ethernet0 = &gmac1;
-		mmc0 = &sdmmc;
-		mmc1 = &sdhci;
-	};
-
-	chosen {
-		stdout-path = "serial2:1500000n8";
-	};
-
-	adc-keys {
-		compatible = "adc-keys";
-		io-channels = <&saradc 0>;
-		io-channel-names = "buttons";
-		keyup-threshold-microvolt = <1800000>;
-		poll-interval = <100>;
-
-		button-maskrom {
-			label = "Maskrom";
-			linux,code = <KEY_VENDOR>;
-			press-threshold-microvolt = <1800>;
-		};
-	};
-
 	gpio-keys {
 		compatible = "gpio-keys";
 		pinctrl-names = "default";
@@ -46,17 +16,6 @@ button-user {
 		};
 	};
 
-	hdmi-con {
-		compatible = "hdmi-connector";
-		type = "a";
-
-		port {
-			hdmi_con_in: endpoint {
-				remote-endpoint = <&hdmi0_out_con>;
-			};
-		};
-	};
-
 	leds {
 		compatible = "gpio-leds";
 
@@ -89,48 +48,6 @@ lan2_led: led-3 {
 		};
 	};
 
-	vcc5v0_sys: regulator-vcc5v0-sys {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc5v0_sys";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-	};
-
-	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
-		compatible = "regulator-fixed";
-		regulator-name = "vcc_1v1_nldo_s3";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <1100000>;
-		regulator-max-microvolt = <1100000>;
-		vin-supply = <&vcc5v0_sys>;
-	};
-
-	vcc_3v3_s0: regulator-vcc-3v3-s0 {
-		compatible = "regulator-fixed";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-		regulator-name = "vcc_3v3_s0";
-		vin-supply = <&vcc_3v3_s3>;
-	};
-
-	vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
-		compatible = "regulator-fixed";
-		enable-active-high;
-		gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&sd_s0_pwr>;
-		regulator-name = "vcc_3v3_sd_s0";
-		regulator-boot-on;
-		regulator-max-microvolt = <3000000>;
-		regulator-min-microvolt = <3000000>;
-		vin-supply = <&vcc_3v3_s3>;
-	};
-
 	vcc5v0_usb_otg0: regulator-vcc5v0-usb-otg0 {
 		compatible = "regulator-fixed";
 		enable-active-high;
@@ -142,225 +59,6 @@ vcc5v0_usb_otg0: regulator-vcc5v0-usb-otg0 {
 		regulator-max-microvolt = <5000000>;
 		vin-supply = <&vcc5v0_sys>;
 	};
-
-	vcc5v0_host_20: regulator-vcc5v0-host-20 {
-		compatible = "regulator-fixed";
-		enable-active-high;
-		gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&vcc5v0_host20_en>;
-		regulator-name = "vcc5v0_host_20";
-		regulator-min-microvolt = <5000000>;
-		regulator-max-microvolt = <5000000>;
-		vin-supply = <&vcc5v0_sys>;
-	};
-};
-
-&combphy0_ps {
-	status = "okay";
-};
-
-&combphy2_psu {
-	status = "okay";
-};
-
-&cpu_b0 {
-	cpu-supply = <&vdd_cpu_big0_s0>;
-};
-
-&cpu_b1 {
-	cpu-supply = <&vdd_cpu_big0_s0>;
-};
-
-&cpu_b2 {
-	cpu-supply = <&vdd_cpu_big1_s0>;
-};
-
-&cpu_b3 {
-	cpu-supply = <&vdd_cpu_big1_s0>;
-};
-
-&cpu_l0 {
-	cpu-supply = <&vdd_cpu_lit_s0>;
-};
-
-&cpu_l1 {
-	cpu-supply = <&vdd_cpu_lit_s0>;
-};
-
-&cpu_l2 {
-	cpu-supply = <&vdd_cpu_lit_s0>;
-};
-
-&cpu_l3 {
-	cpu-supply = <&vdd_cpu_lit_s0>;
-};
-
-&gmac1 {
-	clock_in_out = "output";
-	phy-handle = <&rgmii_phy1>;
-	phy-mode = "rgmii-rxid"; /* Vendor provided tx delay value below */
-	phy-supply = <&vcc_3v3_s3>;
-	pinctrl-0 = <&gmac1_miim
-		     &gmac1_tx_bus2
-		     &gmac1_rx_bus2
-		     &gmac1_rgmii_clk
-		     &gmac1_rgmii_bus>;
-	pinctrl-names = "default";
-	tx_delay = <0x42>;
-	status = "okay";
-};
-
-&gpu {
-	mali-supply = <&vdd_gpu_s0>;
-	status = "okay";
-};
-
-&hdmi0 {
-	frl-enable-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_LOW>;
-	pinctrl-0 = <&hdmim0_tx0_cec &hdmim0_tx0_hpd
-		     &hdmim0_tx0_scl &hdmim0_tx0_sda &hdmi0_tx_on_h>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&hdmi0_in {
-	hdmi0_in_vp0: endpoint {
-		remote-endpoint = <&vp0_out_hdmi0>;
-	};
-};
-
-&hdmi0_out {
-	hdmi0_out_con: endpoint {
-		remote-endpoint = <&hdmi_con_in>;
-	};
-};
-
-&hdmi0_sound {
-	status = "okay";
-};
-
-&hdptxphy0 {
-	status = "okay";
-};
-
-&i2c0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c0m2_xfer>;
-	status = "okay";
-
-	vdd_cpu_big0_s0: regulator@42 {
-		compatible = "rockchip,rk8602";
-		reg = <0x42>;
-		fcs,suspend-voltage-selector = <1>;
-		regulator-name = "vdd_cpu_big0_s0";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <550000>;
-		regulator-max-microvolt = <1050000>;
-		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
-
-		regulator-state-mem {
-			regulator-off-in-suspend;
-		};
-	};
-
-	vdd_cpu_big1_s0: regulator@43 {
-		compatible = "rockchip,rk8603", "rockchip,rk8602";
-		reg = <0x43>;
-		fcs,suspend-voltage-selector = <1>;
-		regulator-name = "vdd_cpu_big1_s0";
-		regulator-always-on;
-		regulator-boot-on;
-		regulator-min-microvolt = <550000>;
-		regulator-max-microvolt = <1050000>;
-		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
-
-		regulator-state-mem {
-			regulator-off-in-suspend;
-		};
-	};
-};
-
-&i2c2 {
-	status = "okay";
-
-	vdd_npu_s0: regulator@42 {
-		compatible = "rockchip,rk8602";
-		reg = <0x42>;
-		fcs,suspend-voltage-selector = <1>;
-		regulator-name = "vdd_npu_s0";
-		regulator-min-microvolt = <550000>;
-		regulator-max-microvolt = <950000>;
-		regulator-ramp-delay = <2300>;
-		vin-supply = <&vcc5v0_sys>;
-
-		regulator-state-mem {
-			regulator-off-in-suspend;
-		};
-	};
-};
-
-&i2c6 {
-	clock-frequency = <200000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&i2c6m0_xfer>;
-	status = "okay";
-
-	hym8563: rtc@51 {
-		compatible = "haoyu,hym8563";
-		reg = <0x51>;
-		#clock-cells = <0>;
-		clock-output-names = "hym8563";
-		pinctrl-names = "default";
-		pinctrl-0 = <&rtc_int>;
-		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
-		wakeup-source;
-	};
-};
-
-&i2s5_8ch {
-	status = "okay";
-};
-
-&mdio1 {
-	rgmii_phy1: ethernet-phy@1 {
-		compatible = "ethernet-phy-id001c.c916";
-		reg = <0x1>;
-		pinctrl-names = "default";
-		pinctrl-0 = <&rtl8211f_rst>;
-		reset-assert-us = <20000>;
-		reset-deassert-us = <100000>;
-		reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
-	};
-};
-
-&pcie2x1l1 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie20x1_1_perstn_m2>;
-	reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc_3v3_s3>;
-	status = "okay";
-};
-
-&pcie2x1l2 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&pcie20x1_2_perstn_m0>, <&pcie20x1m0_clkreqn>;
-	supports-clkreq;
-	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
-	vpcie3v3-supply = <&vcc_3v3_s3>;
-	status = "okay";
-};
-
-&pd_gpu {
-	domain-supply = <&vdd_gpu_s0>;
-};
-
-&pd_npu {
-	domain-supply = <&vdd_npu_s0>;
 };
 
 &pinctrl {
@@ -392,497 +90,9 @@ lan2_led_pin: lan2-led-pin {
 		};
 	};
 
-	hdmi {
-		hdmi0_tx_on_h: hdmi0-tx-on-h {
-			rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-	};
-
-	hym8563 {
-		rtc_int: rtc-int {
-			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-	};
-
-	pcie {
-		pcie20x1_1_perstn_m2: pcie20x1-1-perstn-m2 {
-			rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-
-		pcie20x1_2_perstn_m0: pcie20x1-2-perstn-m0 {
-			rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-	};
-
-	sdmmc {
-		sdmmc_det_pin: sdmmc-det-pin {
-			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
-		};
-
-		sd_s0_pwr: sd-s0-pwr {
-			rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
-		};
-	};
-
 	usb {
 		typec5v_pwren: typec5v-pwren {
 			rockchip,pins = <1 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>;
 		};
-
-		vcc5v0_host20_en: vcc5v0-host20-en {
-			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-	};
-
-	rtl8211f {
-		rtl8211f_rst: rtl8211f-rst {
-			rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
-		};
-	};
-};
-
-&rknn_core_0 {
-	npu-supply = <&vdd_npu_s0>;
-	sram-supply = <&vdd_npu_s0>;
-	status = "okay";
-};
-
-&rknn_core_1 {
-	npu-supply = <&vdd_npu_s0>;
-	sram-supply = <&vdd_npu_s0>;
-	status = "okay";
-};
-
-&rknn_core_2 {
-	npu-supply = <&vdd_npu_s0>;
-	sram-supply = <&vdd_npu_s0>;
-	status = "okay";
-};
-
-&rknn_mmu_0 {
-	status = "okay";
-};
-
-&rknn_mmu_1 {
-	status = "okay";
-};
-
-&rknn_mmu_2 {
-	status = "okay";
-};
-
-&saradc {
-	vref-supply = <&avcc_1v8_s0>;
-	status = "okay";
-};
-
-&sdhci {
-	bus-width = <8>;
-	no-sdio;
-	no-sd;
-	non-removable;
-	mmc-hs200-1_8v;
-	status = "okay";
-};
-
-&sdmmc {
-	bus-width = <4>;
-	cap-sd-highspeed;
-	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
-	disable-wp;
-	max-frequency = <150000000>;
-	no-mmc;
-	no-sdio;
-	sd-uhs-sdr104;
-	pinctrl-names = "default";
-	pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det_pin>;
-	vmmc-supply = <&vcc_3v3_sd_s0>;
-	vqmmc-supply = <&vccio_sd_s0>;
-	status = "okay";
-};
-
-&spi2 {
-	status = "okay";
-	assigned-clocks = <&cru CLK_SPI2>;
-	assigned-clock-rates = <200000000>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
-	num-cs = <1>;
-
-	pmic@0 {
-		compatible = "rockchip,rk806";
-		spi-max-frequency = <1000000>;
-		reg = <0x0>;
-
-		interrupt-parent = <&gpio0>;
-		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
-			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
-
-		system-power-controller;
-
-		vcc1-supply = <&vcc5v0_sys>;
-		vcc2-supply = <&vcc5v0_sys>;
-		vcc3-supply = <&vcc5v0_sys>;
-		vcc4-supply = <&vcc5v0_sys>;
-		vcc5-supply = <&vcc5v0_sys>;
-		vcc6-supply = <&vcc5v0_sys>;
-		vcc7-supply = <&vcc5v0_sys>;
-		vcc8-supply = <&vcc5v0_sys>;
-		vcc9-supply = <&vcc5v0_sys>;
-		vcc10-supply = <&vcc5v0_sys>;
-		vcc11-supply = <&vcc_2v0_pldo_s3>;
-		vcc12-supply = <&vcc5v0_sys>;
-		vcc13-supply = <&vcc_1v1_nldo_s3>;
-		vcc14-supply = <&vcc_1v1_nldo_s3>;
-		vcca-supply = <&vcc5v0_sys>;
-
-		gpio-controller;
-		#gpio-cells = <2>;
-
-		rk806_dvs1_null: dvs1-null-pins {
-			pins = "gpio_pwrctrl1";
-			function = "pin_fun0";
-		};
-
-		rk806_dvs2_null: dvs2-null-pins {
-			pins = "gpio_pwrctrl2";
-			function = "pin_fun0";
-		};
-
-		rk806_dvs3_null: dvs3-null-pins {
-			pins = "gpio_pwrctrl3";
-			function = "pin_fun0";
-		};
-
-		regulators {
-			vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
-				regulator-boot-on;
-				regulator-min-microvolt = <550000>;
-				regulator-max-microvolt = <950000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_gpu_s0";
-				regulator-enable-ramp-delay = <400>;
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <550000>;
-				regulator-max-microvolt = <950000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_cpu_lit_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			vdd_log_s0: dcdc-reg3 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <675000>;
-				regulator-max-microvolt = <750000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_log_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-					regulator-suspend-microvolt = <750000>;
-				};
-			};
-
-			vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <550000>;
-				regulator-max-microvolt = <950000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_vdenc_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			vdd_ddr_s0: dcdc-reg5 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <675000>;
-				regulator-max-microvolt = <900000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_ddr_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-					regulator-suspend-microvolt = <850000>;
-				};
-			};
-
-			vdd2_ddr_s3: dcdc-reg6 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-name = "vdd2_ddr_s3";
-
-				regulator-state-mem {
-					regulator-on-in-suspend;
-				};
-			};
-
-			vcc_2v0_pldo_s3: dcdc-reg7 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <2000000>;
-				regulator-max-microvolt = <2000000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vdd_2v0_pldo_s3";
-
-				regulator-state-mem {
-					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <2000000>;
-				};
-			};
-
-			vcc_3v3_s3: dcdc-reg8 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-name = "vcc_3v3_s3";
-
-				regulator-state-mem {
-					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <3300000>;
-				};
-			};
-
-			vddq_ddr_s0: dcdc-reg9 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-name = "vddq_ddr_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			vcc_1v8_s3: dcdc-reg10 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-name = "vcc_1v8_s3";
-
-				regulator-state-mem {
-					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <1800000>;
-				};
-			};
-
-			avcc_1v8_s0: pldo-reg1 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-name = "avcc_1v8_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-					regulator-suspend-microvolt = <1800000>;
-				};
-			};
-
-			vcc_1v8_s0: pldo-reg2 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-name = "vcc_1v8_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-					regulator-suspend-microvolt = <1800000>;
-				};
-			};
-
-			avdd_1v2_s0: pldo-reg3 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <1200000>;
-				regulator-max-microvolt = <1200000>;
-				regulator-name = "avdd_1v2_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			avcc_3v3_s0: pldo-reg4 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <3300000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "avcc_3v3_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			vccio_sd_s0: pldo-reg5 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <3300000>;
-				regulator-ramp-delay = <12500>;
-				regulator-name = "vccio_sd_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			pldo6_s3: pldo-reg6 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <1800000>;
-				regulator-max-microvolt = <1800000>;
-				regulator-name = "pldo6_s3";
-
-				regulator-state-mem {
-					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <1800000>;
-				};
-			};
-
-			vdd_0v75_s3: nldo-reg1 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt = <750000>;
-				regulator-name = "vdd_0v75_s3";
-
-				regulator-state-mem {
-					regulator-on-in-suspend;
-					regulator-suspend-microvolt = <750000>;
-				};
-			};
-
-			avdd_ddr_pll_s0: nldo-reg2 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <850000>;
-				regulator-name = "avdd_ddr_pll_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-					regulator-suspend-microvolt = <850000>;
-				};
-			};
-
-			avdd_0v75_s0: nldo-reg3 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt = <750000>;
-				regulator-name = "avdd_0v75_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			avdd_0v85_s0: nldo-reg4 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <850000>;
-				regulator-max-microvolt = <850000>;
-				regulator-name = "avdd_0v85_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-
-			vdd_0v75_s0: nldo-reg5 {
-				regulator-always-on;
-				regulator-boot-on;
-				regulator-min-microvolt = <750000>;
-				regulator-max-microvolt = <750000>;
-				regulator-name = "vdd_0v75_s0";
-
-				regulator-state-mem {
-					regulator-off-in-suspend;
-				};
-			};
-		};
-	};
-};
-
-&tsadc {
-	status = "okay";
-};
-
-&u2phy0 {
-	status = "okay";
-};
-
-&u2phy0_otg {
-	phy-supply = <&vcc5v0_usb_otg0>;
-	status = "okay";
-};
-
-&u2phy2 {
-	status = "okay";
-};
-
-&u2phy2_host {
-	phy-supply = <&vcc5v0_host_20>;
-	status = "okay";
-};
-
-&uart2 {
-	pinctrl-0 = <&uart2m0_xfer>;
-	pinctrl-names = "default";
-	status = "okay";
-};
-
-&usb_host0_ehci {
-	status = "okay";
-};
-
-&usb_host0_ohci {
-	status = "okay";
-};
-
-&usb_host0_xhci {
-	dr_mode = "host";
-	status = "okay";
-};
-
-&usbdp_phy0 {
-	status = "okay";
-};
-
-&vop {
-	status = "okay";
-};
-
-&vop_mmu {
-	status = "okay";
-};
-
-&vp0 {
-	vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
-		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
-		remote-endpoint = <&hdmi0_in_vp0>;
 	};
 };
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi.dtsi
new file mode 100644
index 000000000000..22b0cdee22b4
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi.dtsi
@@ -0,0 +1,797 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include <dt-bindings/pinctrl/rockchip.h>
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/soc/rockchip,vop2.h>
+#include "rk3588s.dtsi"
+
+/ {
+	aliases {
+		ethernet0 = &gmac1;
+		mmc0 = &sdmmc;
+		mmc1 = &sdhci;
+	};
+
+	chosen {
+		stdout-path = "serial2:1500000n8";
+	};
+
+	adc-keys {
+		compatible = "adc-keys";
+		io-channels = <&saradc 0>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-maskrom {
+			label = "Maskrom";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <1800>;
+		};
+	};
+
+	hdmi-con {
+		compatible = "hdmi-connector";
+		type = "a";
+
+		port {
+			hdmi_con_in: endpoint {
+				remote-endpoint = <&hdmi0_out_con>;
+			};
+		};
+	};
+
+	vcc5v0_sys: regulator-vcc5v0-sys {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0_sys";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	vcc_1v1_nldo_s3: regulator-vcc-1v1-nldo-s3 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc_1v1_nldo_s3";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <1100000>;
+		regulator-max-microvolt = <1100000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc_3v3_s0: regulator-vcc-3v3-s0 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		regulator-name = "vcc_3v3_s0";
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc_3v3_sd_s0: regulator-vcc-3v3-sd-s0 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio4 RK_PB4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&sd_s0_pwr>;
+		regulator-name = "vcc_3v3_sd_s0";
+		regulator-boot-on;
+		regulator-max-microvolt = <3000000>;
+		regulator-min-microvolt = <3000000>;
+		vin-supply = <&vcc_3v3_s3>;
+	};
+
+	vcc5v0_host_20: regulator-vcc5v0-host-20 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&vcc5v0_host20_en>;
+		regulator-name = "vcc5v0_host_20";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&combphy0_ps {
+	status = "okay";
+};
+
+&combphy2_psu {
+	status = "okay";
+};
+
+&cpu_b0 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b1 {
+	cpu-supply = <&vdd_cpu_big0_s0>;
+};
+
+&cpu_b2 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_b3 {
+	cpu-supply = <&vdd_cpu_big1_s0>;
+};
+
+&cpu_l0 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l1 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l2 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&cpu_l3 {
+	cpu-supply = <&vdd_cpu_lit_s0>;
+};
+
+&gmac1 {
+	clock_in_out = "output";
+	phy-handle = <&rgmii_phy1>;
+	phy-mode = "rgmii-rxid"; /* Vendor provided tx delay value below */
+	phy-supply = <&vcc_3v3_s3>;
+	pinctrl-0 = <&gmac1_miim
+		     &gmac1_tx_bus2
+		     &gmac1_rx_bus2
+		     &gmac1_rgmii_clk
+		     &gmac1_rgmii_bus>;
+	pinctrl-names = "default";
+	tx_delay = <0x42>;
+	status = "okay";
+};
+
+&gpu {
+	mali-supply = <&vdd_gpu_s0>;
+	status = "okay";
+};
+
+&hdmi0 {
+	frl-enable-gpios = <&gpio4 RK_PB6 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&hdmim0_tx0_cec &hdmim0_tx0_hpd
+		     &hdmim0_tx0_scl &hdmim0_tx0_sda &hdmi0_tx_on_h>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&hdmi0_in {
+	hdmi0_in_vp0: endpoint {
+		remote-endpoint = <&vp0_out_hdmi0>;
+	};
+};
+
+&hdmi0_out {
+	hdmi0_out_con: endpoint {
+		remote-endpoint = <&hdmi_con_in>;
+	};
+};
+
+&hdmi0_sound {
+	status = "okay";
+};
+
+&hdptxphy0 {
+	status = "okay";
+};
+
+&i2c0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0m2_xfer>;
+	status = "okay";
+
+	vdd_cpu_big0_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big0_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+
+	vdd_cpu_big1_s0: regulator@43 {
+		compatible = "rockchip,rk8603", "rockchip,rk8602";
+		reg = <0x43>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_cpu_big1_s0";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <1050000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c2 {
+	status = "okay";
+
+	vdd_npu_s0: regulator@42 {
+		compatible = "rockchip,rk8602";
+		reg = <0x42>;
+		fcs,suspend-voltage-selector = <1>;
+		regulator-name = "vdd_npu_s0";
+		regulator-min-microvolt = <550000>;
+		regulator-max-microvolt = <950000>;
+		regulator-ramp-delay = <2300>;
+		vin-supply = <&vcc5v0_sys>;
+
+		regulator-state-mem {
+			regulator-off-in-suspend;
+		};
+	};
+};
+
+&i2c6 {
+	clock-frequency = <200000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c6m0_xfer>;
+	status = "okay";
+
+	hym8563: rtc@51 {
+		compatible = "haoyu,hym8563";
+		reg = <0x51>;
+		#clock-cells = <0>;
+		clock-output-names = "hym8563";
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtc_int>;
+		interrupt-parent = <&gpio0>;
+		interrupts = <RK_PB0 IRQ_TYPE_LEVEL_LOW>;
+		wakeup-source;
+	};
+};
+
+&i2s5_8ch {
+	status = "okay";
+};
+
+&mdio1 {
+	rgmii_phy1: ethernet-phy@1 {
+		compatible = "ethernet-phy-id001c.c916";
+		reg = <0x1>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&rtl8211f_rst>;
+		reset-assert-us = <20000>;
+		reset-deassert-us = <100000>;
+		reset-gpios = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
+	};
+};
+
+&pcie2x1l1 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_1_perstn_m2>;
+	reset-gpios = <&gpio1 RK_PA7 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc_3v3_s3>;
+	status = "okay";
+};
+
+&pcie2x1l2 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&pcie20x1_2_perstn_m0>, <&pcie20x1m0_clkreqn>;
+	supports-clkreq;
+	reset-gpios = <&gpio3 RK_PD1 GPIO_ACTIVE_HIGH>;
+	vpcie3v3-supply = <&vcc_3v3_s3>;
+	status = "okay";
+};
+
+&pd_gpu {
+	domain-supply = <&vdd_gpu_s0>;
+};
+
+&pd_npu {
+	domain-supply = <&vdd_npu_s0>;
+};
+
+&pinctrl {
+	hdmi {
+		hdmi0_tx_on_h: hdmi0-tx-on-h {
+			rockchip,pins = <4 RK_PB6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	hym8563 {
+		rtc_int: rtc-int {
+			rockchip,pins = <0 RK_PB0 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie20x1_1_perstn_m2: pcie20x1-1-perstn-m2 {
+			rockchip,pins = <1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		pcie20x1_2_perstn_m0: pcie20x1-2-perstn-m0 {
+			rockchip,pins = <3 RK_PD1 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	sdmmc {
+		sdmmc_det_pin: sdmmc-det-pin {
+			rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+
+		sd_s0_pwr: sd-s0-pwr {
+			rockchip,pins = <4 RK_PB4 RK_FUNC_GPIO &pcfg_pull_up>;
+		};
+	};
+
+	usb {
+		vcc5v0_host20_en: vcc5v0-host20-en {
+			rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	rtl8211f {
+		rtl8211f_rst: rtl8211f-rst {
+			rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&rknn_core_0 {
+	npu-supply = <&vdd_npu_s0>;
+	sram-supply = <&vdd_npu_s0>;
+	status = "okay";
+};
+
+&rknn_core_1 {
+	npu-supply = <&vdd_npu_s0>;
+	sram-supply = <&vdd_npu_s0>;
+	status = "okay";
+};
+
+&rknn_core_2 {
+	npu-supply = <&vdd_npu_s0>;
+	sram-supply = <&vdd_npu_s0>;
+	status = "okay";
+};
+
+&rknn_mmu_0 {
+	status = "okay";
+};
+
+&rknn_mmu_1 {
+	status = "okay";
+};
+
+&rknn_mmu_2 {
+	status = "okay";
+};
+
+&saradc {
+	vref-supply = <&avcc_1v8_s0>;
+	status = "okay";
+};
+
+&sdhci {
+	bus-width = <8>;
+	no-sdio;
+	no-sd;
+	non-removable;
+	mmc-hs200-1_8v;
+	status = "okay";
+};
+
+&sdmmc {
+	bus-width = <4>;
+	cap-sd-highspeed;
+	cd-gpios = <&gpio0 RK_PA4 GPIO_ACTIVE_LOW>;
+	disable-wp;
+	max-frequency = <150000000>;
+	no-mmc;
+	no-sdio;
+	sd-uhs-sdr104;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sdmmc_bus4 &sdmmc_clk &sdmmc_cmd &sdmmc_det_pin>;
+	vmmc-supply = <&vcc_3v3_sd_s0>;
+	vqmmc-supply = <&vccio_sd_s0>;
+	status = "okay";
+};
+
+&spi2 {
+	status = "okay";
+	assigned-clocks = <&cru CLK_SPI2>;
+	assigned-clock-rates = <200000000>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&spi2m2_cs0 &spi2m2_pins>;
+	num-cs = <1>;
+
+	pmic@0 {
+		compatible = "rockchip,rk806";
+		spi-max-frequency = <1000000>;
+		reg = <0x0>;
+
+		interrupt-parent = <&gpio0>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pmic_pins>, <&rk806_dvs1_null>,
+			    <&rk806_dvs2_null>, <&rk806_dvs3_null>;
+
+		system-power-controller;
+
+		vcc1-supply = <&vcc5v0_sys>;
+		vcc2-supply = <&vcc5v0_sys>;
+		vcc3-supply = <&vcc5v0_sys>;
+		vcc4-supply = <&vcc5v0_sys>;
+		vcc5-supply = <&vcc5v0_sys>;
+		vcc6-supply = <&vcc5v0_sys>;
+		vcc7-supply = <&vcc5v0_sys>;
+		vcc8-supply = <&vcc5v0_sys>;
+		vcc9-supply = <&vcc5v0_sys>;
+		vcc10-supply = <&vcc5v0_sys>;
+		vcc11-supply = <&vcc_2v0_pldo_s3>;
+		vcc12-supply = <&vcc5v0_sys>;
+		vcc13-supply = <&vcc_1v1_nldo_s3>;
+		vcc14-supply = <&vcc_1v1_nldo_s3>;
+		vcca-supply = <&vcc5v0_sys>;
+
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		rk806_dvs1_null: dvs1-null-pins {
+			pins = "gpio_pwrctrl1";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs2_null: dvs2-null-pins {
+			pins = "gpio_pwrctrl2";
+			function = "pin_fun0";
+		};
+
+		rk806_dvs3_null: dvs3-null-pins {
+			pins = "gpio_pwrctrl3";
+			function = "pin_fun0";
+		};
+
+		regulators {
+			vdd_gpu_s0: vdd_gpu_mem_s0: dcdc-reg1 {
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_gpu_s0";
+				regulator-enable-ramp-delay = <400>;
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_cpu_lit_s0: vdd_cpu_lit_mem_s0: dcdc-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_cpu_lit_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_log_s0: dcdc-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <750000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_log_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			vdd_vdenc_s0: vdd_vdenc_mem_s0: dcdc-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <550000>;
+				regulator-max-microvolt = <950000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_vdenc_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_ddr_s0: dcdc-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <675000>;
+				regulator-max-microvolt = <900000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_ddr_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			vdd2_ddr_s3: dcdc-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vdd2_ddr_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+				};
+			};
+
+			vcc_2v0_pldo_s3: dcdc-reg7 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <2000000>;
+				regulator-max-microvolt = <2000000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vdd_2v0_pldo_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <2000000>;
+				};
+			};
+
+			vcc_3v3_s3: dcdc-reg8 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-name = "vcc_3v3_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <3300000>;
+				};
+			};
+
+			vddq_ddr_s0: dcdc-reg9 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-name = "vddq_ddr_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vcc_1v8_s3: dcdc-reg10 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			avcc_1v8_s0: pldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "avcc_1v8_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vcc_1v8_s0: pldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "vcc_1v8_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			avdd_1v2_s0: pldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1200000>;
+				regulator-max-microvolt = <1200000>;
+				regulator-name = "avdd_1v2_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			avcc_3v3_s0: pldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <3300000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "avcc_3v3_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vccio_sd_s0: pldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <3300000>;
+				regulator-ramp-delay = <12500>;
+				regulator-name = "vccio_sd_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			pldo6_s3: pldo-reg6 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <1800000>;
+				regulator-max-microvolt = <1800000>;
+				regulator-name = "pldo6_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <1800000>;
+				};
+			};
+
+			vdd_0v75_s3: nldo-reg1 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s3";
+
+				regulator-state-mem {
+					regulator-on-in-suspend;
+					regulator-suspend-microvolt = <750000>;
+				};
+			};
+
+			avdd_ddr_pll_s0: nldo-reg2 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "avdd_ddr_pll_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+					regulator-suspend-microvolt = <850000>;
+				};
+			};
+
+			avdd_0v75_s0: nldo-reg3 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "avdd_0v75_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			avdd_0v85_s0: nldo-reg4 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <850000>;
+				regulator-max-microvolt = <850000>;
+				regulator-name = "avdd_0v85_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+
+			vdd_0v75_s0: nldo-reg5 {
+				regulator-always-on;
+				regulator-boot-on;
+				regulator-min-microvolt = <750000>;
+				regulator-max-microvolt = <750000>;
+				regulator-name = "vdd_0v75_s0";
+
+				regulator-state-mem {
+					regulator-off-in-suspend;
+				};
+			};
+		};
+	};
+};
+
+&tsadc {
+	status = "okay";
+};
+
+&u2phy0 {
+	status = "okay";
+};
+
+&u2phy0_otg {
+	phy-supply = <&vcc5v0_usb_otg0>;
+	status = "okay";
+};
+
+&u2phy2 {
+	status = "okay";
+};
+
+&u2phy2_host {
+	phy-supply = <&vcc5v0_host_20>;
+	status = "okay";
+};
+
+&uart2 {
+	pinctrl-0 = <&uart2m0_xfer>;
+	pinctrl-names = "default";
+	status = "okay";
+};
+
+&usb_host0_ehci {
+	status = "okay";
+};
+
+&usb_host0_ohci {
+	status = "okay";
+};
+
+&usb_host0_xhci {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbdp_phy0 {
+	status = "okay";
+};
+
+&vop {
+	status = "okay";
+};
+
+&vop_mmu {
+	status = "okay";
+};
+
+&vp0 {
+	vp0_out_hdmi0: endpoint@ROCKCHIP_VOP2_EP_HDMI0 {
+		reg = <ROCKCHIP_VOP2_EP_HDMI0>;
+		remote-endpoint = <&hdmi0_in_vp0>;
+	};
+};

-- 
2.55.0

[PATCH v6 12/12] arm64: dts: rockchip: add support for NanoPi M6 board

[Joachim Eastwood via B4 Relay]

From: Joachim Eastwood <joachim.eastwood@gmail.com>

The NanoPi M6 (V1) board shares most of the features of the R6 boards.

Main differences:
* M.2 M-key slot with PCIe (Also present on R6C)
* M.2 E-key slot with PCIe and USB (from hub)
* 1 additional USB 2.0 port from an on-board USB hub
* RT5616 audio CODEC

Signed-off-by: Joachim Eastwood <joachim.eastwood@gmail.com>
---
 arch/arm64/boot/dts/rockchip/Makefile              |   1 +
 .../arm64/boot/dts/rockchip/rk3588s-nanopi-m6.dtsi | 142 +++++++++++++++++++++
 .../boot/dts/rockchip/rk3588s-nanopi-m6v1.dts      |  57 +++++++++
 3 files changed, 200 insertions(+)

diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index e7936a21c118..be2c8cc810b7 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -229,6 +229,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-gameforce-ace.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-indiedroid-nova.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-khadas-edge2.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-lubancat-4.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-m6v1.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6s.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-nanopi-r6c.dtb
 dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3588s-odroid-m2.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6.dtsi b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6.dtsi
new file mode 100644
index 000000000000..6644d3b72c9c
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6.dtsi
@@ -0,0 +1,142 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+#include "rk3588s-nanopi.dtsi"
+
+/ {
+	adc-keys-1 {
+		compatible = "adc-keys";
+		io-channels = <&saradc 1>;
+		io-channel-names = "buttons";
+		keyup-threshold-microvolt = <1800000>;
+		poll-interval = <100>;
+
+		button-maskrom {
+			label = "Recovery";
+			linux,code = <KEY_VENDOR>;
+			press-threshold-microvolt = <1800>;
+		};
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		sys_led: led-0 {
+			label = "sys_led";
+			gpios = <&gpio1 RK_PA4 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+			pinctrl-names = "default";
+			pinctrl-0 = <&sys_led_pin>;
+		};
+
+		user_led: led-1 {
+			label = "user_led";
+			gpios = <&gpio1 RK_PA6 GPIO_ACTIVE_HIGH>;
+			pinctrl-names = "default";
+			pinctrl-0 = <&user_led_pin>;
+		};
+	};
+
+	vcc_3v3_pcie: regulator-vcc-3v3-pcie {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio3 RK_PC6 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pcie2_2_pwren>;
+		regulator-name = "vcc_3v3_pcie";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vcc5v0_usb_otg0: regulator-vcc5v0-usb-otg0 {
+		compatible = "regulator-fixed";
+		enable-active-high;
+		gpios = <&gpio3 RK_PD4 GPIO_ACTIVE_HIGH>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&typec5v_pwren>;
+		regulator-name = "vcc5v0_usb_otg0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+
+	vdd_mpcie_3v3: regulator-vdd-mpcie-3v3 {
+		compatible = "regulator-fixed";
+		/* Controlled by EXT_EN on RK806 */
+		regulator-name = "vdd_mpcie_3v3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		vin-supply = <&vcc5v0_sys>;
+	};
+};
+
+&i2c7 {
+	clock-frequency = <200000>;
+	status = "okay";
+};
+
+&i2s0_8ch {
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2s0_lrck
+		     &i2s0_mclk
+		     &i2s0_sclk
+		     &i2s0_sdi0
+		     &i2s0_sdo0>;
+	status = "okay";
+};
+
+&pcie2x1l1 { /* M.2 E-key 2230 */
+	vpcie3v3-supply = <&vdd_mpcie_3v3>;
+};
+
+&pcie2x1l2 { /* M.2 M-key 2280 */
+	pinctrl-0 = <&pcie20x1_2_perstn_m0>, <&pcie20x1m0_clkreqn>, <&pcie20x1m0_waken>;
+	vpcie3v3-supply = <&vcc_3v3_pcie>;
+};
+
+&pinctrl {
+	gpio-leds {
+		sys_led_pin: sys-led-pin {
+			rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+
+		user_led_pin: user-led-pin {
+			rockchip,pins = <1 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	headphone {
+		hp_det: hp-det {
+			rockchip,pins = <1 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	pcie {
+		pcie2_2_pwren: pcie2-2-pwren {
+			rockchip,pins = <3 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+
+	usb {
+		typec5v_pwren: typec5v-pwren {
+			rockchip,pins = <3 RK_PD4 RK_FUNC_GPIO &pcfg_pull_none>;
+		};
+	};
+};
+
+&u2phy3 {
+	status = "okay";
+};
+
+&u2phy3_host {
+	phy-supply = <&vcc5v0_host_20>;
+	status = "okay";
+};
+
+&usb_host1_ehci {
+	status = "okay";
+};
+
+&usb_host1_ohci {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6v1.dts b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6v1.dts
new file mode 100644
index 000000000000..2a22435f46c8
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-nanopi-m6v1.dts
@@ -0,0 +1,57 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+
+/dts-v1/;
+
+#include "rk3588s-nanopi-m6.dtsi"
+
+/ {
+	model = "FriendlyElec NanoPi M6";
+	compatible = "friendlyarm,nanopi-m6", "rockchip,rk3588s";
+
+	analog-sound {
+		compatible = "audio-graph-card";
+		label = "rk3588s-rt5616";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&hp_det>;
+		hp-det-gpios = <&gpio1 RK_PC4 GPIO_ACTIVE_LOW>;
+
+		dais = <&i2s0_8ch_p0>;
+		routing =
+			"Headphones", "HPOL",
+			"Headphones", "HPOR",
+			"MIC1", "Microphone Jack",
+			"Microphone Jack", "micbias1";
+		widgets =
+			"Headphone", "Headphones",
+			"Microphone", "Microphone Jack";
+	};
+};
+
+&i2c7 {
+	audio-codec@1b {
+		compatible = "realtek,rt5616";
+		reg = <0x1b>;
+		assigned-clocks = <&cru I2S0_8CH_MCLKOUT_TO_IO>;
+		assigned-clock-rates = <12288000>;
+		clocks = <&cru I2S0_8CH_MCLKOUT_TO_IO>;
+		clock-names = "mclk";
+		#sound-dai-cells = <0>;
+
+		port {
+			rt5616_p0: endpoint {
+				remote-endpoint = <&i2s0_8ch_p0_0>;
+			};
+		};
+	};
+};
+
+&i2s0_8ch {
+	i2s0_8ch_p0: port {
+		i2s0_8ch_p0_0: endpoint {
+			dai-format = "i2s";
+			mclk-fs = <256>;
+			remote-endpoint = <&rt5616_p0>;
+		};
+	};
+};

-- 
2.55.0