[PATCH v2 00/20] pmdomain: st: ux500: Implement ux500 power domains

[PATCH v2 00/20] pmdomain: st: ux500: Implement ux500 power domains

[Linus Walleij]

This series pays off technical debt from the beginning of the device
tree for ARM initiative in the early 2010s.

Today the Ux500 SoC specifically DB8500 is using what is called "EPOD
regulators" (EPOD = Electric POwer Domain) to control its power domains.
This was done like this because at the time, power domains did not exist
as a concept in the Linux kernel.

This patch series completes the ambitious work started in commit
cd931dcfda5e ("ARM: ux500: Initial support for PM domains") which added
a dummy domain driver for Ux500 in the following steps:

- Convert the old Ux500 power domain text DT bindings to YAML schema.

- Extend the bindings with all the 16 power domains actually existing in
  the hardware.

- Add these domains to the existing ux500 power domain driver (still as
  dummy domains).

- Add the power domains to the DB8500 SoC DTSI file.

- Move code over from the EPOD regulators to the actual power domain
  driver. Since the two drivers now control the same hardware, make the
  drivers mutually exclusive.

- Modify the MCDE display driver to use the power domain instead of the
  EPOD regulators.

- Modify the DMA40 DMA controller to use the power domain instead of the
  EPOD regulators.

- Delete the old EPOD regulators.

- Delete the references to the unused EPOD regulators from the device
  tree.

The series is ordered so binding updates and compatibility glue precede
the DTS and driver changes that depend on them.

MERGE STRATEGY:

1. Device tree bindings need review, before that the series is a
   no-go.

2. For simplicity, the series can be merged in separate paths and
   subsystems as there are no build-time dependencies, as long as the
   result ends up in kernel v7.4.

   Once the concept and patches are ACKed by the power domain folks, I
   will send the patches that can be split out individually to each
   maintainer and it can all be merged in parallel. I will send a
   pull request to the SoC tree with bindings and DTS changes.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
Changes in v2:
- Went on a detour clean-up job relating to buck regulators.
  Rebased on kernel v7.3-rc1 and the regulator re-works in this
  mail thread:
  https://lore.kernel.org/mfd/20260901-ux500-dts-snowball-regulator-v2-0-fe88b01829bf@kernel.org/
- Drop the PM domain "regulators" entirely, the external components
  now use their actual buck regulators.
- Fix the DB8500 pin controller power domain to use VAPE.
- Allow power-domain references in the l2c2x0, arm,pmu,
  stericsson,u8500-clks, arm,twd-timer, arm,twd-wdt and ste,mcde
  schemas used by the DB8500 DTS additions.
- Treat only negative pm_runtime_put_sync_suspend() returns as errors.
- Fix the MCDE probe error path to disable the main clock after reset.
- Fix Ux500 PM-domain probe error cleanup for domains and provider data.
- Drop the unused Ux500 power-state activity counter.
- Describe Ux500 subdomains in DT and use OF child ID helpers.
- Move DMA40 LCLA power-domain get out of atomic transfer paths.
- Enable runtime PM in the generic SRAM driver so SRAM power domains
  are managed by their owner before DMA40 takes LCLA references.
- Add a DMA40 device link so system PM orders the LCLA SRAM supplier.
- Add binding fixes for the DB8500 PRCMU regulator child nodes.
- Add an MCDE binding update for the new power-domain reference.
- Fix up the DB8500 DTS changes for the remaining VAPE and VSMPS2
  compatibility regulators.
- Link to v1: https://lore.kernel.org/r/20260618-ux500-power-domains-v7-1-v1-0-eb5e50b1a588@kernel.org

---
Linus Walleij (20):
      dt-bindings: power: Convert Ux500 PM domains to schema
      dt-bindings: arm: ux500: Drop NR_DOMAINS
      dt-bindings: arm: Add the actual power domains on U8500
      dt-bindings: mfd: db8500-prcmu: Relax EPOD regulators
      dt-bindings: display: ste,mcde: Allow power domains
      pmdomain: st: ux500: Implement more power domains
      ARM: dts: ux500: Rename power domains node
      dt-bindings: cache: l2c2x0: Document power domain
      dt-bindings: arm: pmu: Allow power domains
      dt-bindings: clock: stericsson,u8500-clks: Allow power domains
      dt-bindings: timer: arm,twd-timer: Allow power domains
      dt-bindings: watchdog: arm,twd-wdt: Allow power domains
      ARM: dts: ux500: Add power domains
      pmdomain: st: ux500: Control DB8500 EPODs
      drm/mcde: Use power domain for display power
      misc: sram: Enable runtime PM
      dmaengine: ste_dma40: Use power domain for LCLA SRAM
      mfd/regulator: db8500-prcmu: Remove EPOD regulators
      dt-bindings: display: ste,mcde: Deprecate EPOD supply
      ARM: dts: ux500: Remove DB8500 EPOD regulators

 Documentation/devicetree/bindings/arm/pmu.yaml     |   3 +
 .../devicetree/bindings/arm/ux500/power_domain.txt |  35 --
 .../devicetree/bindings/cache/l2c2x0.yaml          |   2 +
 .../bindings/clock/stericsson,u8500-clks.yaml      |   3 +
 .../devicetree/bindings/display/ste,mcde.yaml      |  10 +-
 .../bindings/mfd/stericsson,db8500-prcmu.yaml      |  24 +-
 .../power/stericsson,ux500-pm-domains.yaml         |  46 ++
 .../devicetree/bindings/timer/arm,twd-timer.yaml   |   3 +
 .../devicetree/bindings/watchdog/arm,twd-wdt.yaml  |   3 +
 MAINTAINERS                                        |   1 +
 arch/arm/boot/dts/st/ste-dbx5x0.dtsi               | 144 +++---
 arch/arm/mach-ux500/Kconfig                        |   2 +-
 drivers/dma/ste_dma40.c                            | 130 ++++--
 drivers/gpu/drm/mcde/mcde_clk_div.c                |   4 +-
 drivers/gpu/drm/mcde/mcde_display.c                |  11 +-
 drivers/gpu/drm/mcde/mcde_drm.h                    |   2 -
 drivers/gpu/drm/mcde/mcde_drv.c                    |  68 +--
 drivers/gpu/drm/mcde/mcde_dsi.c                    |   1 -
 drivers/mfd/db8500-prcmu.c                         | 239 ----------
 drivers/misc/sram.c                                |   5 +
 drivers/pmdomain/st/ste-ux500-pm-domain.c          | 330 ++++++++++++--
 drivers/regulator/Kconfig                          |  11 -
 drivers/regulator/Makefile                         |   2 -
 drivers/regulator/db8500-prcmu.c                   | 501 ---------------------
 drivers/regulator/dbx500-prcmu.c                   | 155 -------
 drivers/regulator/dbx500-prcmu.h                   |  55 ---
 include/dt-bindings/arm/ux500_pm_domains.h         |  17 +-
 include/linux/regulator/db8500-prcmu.h             |  38 --
 28 files changed, 566 insertions(+), 1279 deletions(-)
---
base-commit: 67aa45aae7efe0162f198f26714f668b759468c4
change-id: 20260618-ux500-power-domains-v7-1-3c9d095828c2

Best regards,
-- 
Linus Walleij <linusw@kernel.org>

[PATCH v2 01/20] dt-bindings: power: Convert Ux500 PM domains to schema

[Linus Walleij]

Convert the legacy Ux500 power domain text binding to YAML.

Move it under bindings/power.

Reference the generic power-domain schema.

Update MAINTAINERS for the new path.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 .../devicetree/bindings/arm/ux500/power_domain.txt | 35 ----------------
 .../power/stericsson,ux500-pm-domains.yaml         | 46 ++++++++++++++++++++++
 MAINTAINERS                                        |  1 +
 3 files changed, 47 insertions(+), 35 deletions(-)

diff --git a/Documentation/devicetree/bindings/arm/ux500/power_domain.txt b/Documentation/devicetree/bindings/arm/ux500/power_domain.txt
deleted file mode 100644
index 5679d1742d3e..000000000000
--- a/Documentation/devicetree/bindings/arm/ux500/power_domain.txt
+++ /dev/null
@@ -1,35 +0,0 @@
-* ST-Ericsson UX500 PM Domains
-
-UX500 supports multiple PM domains which are used to gate power to one or
-more peripherals on the SOC.
-
-The implementation of PM domains for UX500 are based upon the generic PM domain
-and use the corresponding DT bindings.
-
-==PM domain providers==
-
-Required properties:
- - compatible: Must be "stericsson,ux500-pm-domains".
- - #power-domain-cells : Number of cells in a power domain specifier, must be 1.
-
-Example:
-	pm_domains: pm_domains0 {
-		compatible = "stericsson,ux500-pm-domains";
-		#power-domain-cells = <1>;
-	};
-
-==PM domain consumers==
-
-Required properties:
- - power-domains: A phandle and PM domain specifier. Below are the list of
-		valid specifiers:
-
-		Index	Specifier
-		-----	---------
-		0	DOMAIN_VAPE
-
-Example:
-	sdi0_per1@80126000 {
-		compatible = "arm,pl18x", "arm,primecell";
-		power-domains = <&pm_domains DOMAIN_VAPE>
-	};
diff --git a/Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.yaml b/Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.yaml
new file mode 100644
index 000000000000..72c39c083efb
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.yaml
@@ -0,0 +1,46 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/stericsson,ux500-pm-domains.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: ST-Ericsson UX500 power domains
+
+maintainers:
+  - Linus Walleij <linusw@kernel.org>
+  - Ulf Hansson <ulfh@kernel.org>
+
+description:
+  The UX500 power domain controller gates power to one or more peripherals on
+  the SoC. Domain specifiers use one cell containing one of the DOMAIN_*
+  indexes defined in dt-bindings/arm/ux500_pm_domains.h.
+
+allOf:
+  - $ref: power-domain.yaml#
+
+properties:
+  compatible:
+    const: stericsson,ux500-pm-domains
+
+  '#power-domain-cells':
+    const: 1
+
+required:
+  - compatible
+  - '#power-domain-cells'
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/arm/ux500_pm_domains.h>
+
+    pm_domains: power-controller {
+        compatible = "stericsson,ux500-pm-domains";
+        #power-domain-cells = <1>;
+    };
+
+    sdi0_per1@80126000 {
+        compatible = "arm,pl18x", "arm,primecell";
+        power-domains = <&pm_domains DOMAIN_VAPE>;
+    };
diff --git a/MAINTAINERS b/MAINTAINERS
index 3a19da74d00c..560079711469 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -3273,6 +3273,7 @@ F:	Documentation/devicetree/bindings/arm/ux500.yaml
 F:	Documentation/devicetree/bindings/arm/ux500/
 F:	Documentation/devicetree/bindings/gpio/st,nomadik-gpio.yaml
 F:	Documentation/devicetree/bindings/i2c/st,nomadik-i2c.yaml
+F:	Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.yaml
 F:	arch/arm/boot/dts/st/ste-*
 F:	arch/arm/mach-nomadik/
 F:	arch/arm/mach-ux500/

-- 
2.55.0

[PATCH v2 02/20] dt-bindings: arm: ux500: Drop NR_DOMAINS

[Linus Walleij]

Keep the internal Ux500 PM domain count local to the only driver
that uses it.

Do not expose this implementation detail through the DT binding header.

Assisted-by: LLM
Reported-by: Krzysztof Kozlowski <krzk@kernel.org>
Closes: https://lore.kernel.org/linux-devicetree/20260623-just-grinning-peccary-d661ca@quoll/
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 drivers/pmdomain/st/ste-ux500-pm-domain.c  | 2 ++
 include/dt-bindings/arm/ux500_pm_domains.h | 2 --
 2 files changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/pmdomain/st/ste-ux500-pm-domain.c b/drivers/pmdomain/st/ste-ux500-pm-domain.c
index 6896cb4a7b71..c9129a3b1805 100644
--- a/drivers/pmdomain/st/ste-ux500-pm-domain.c
+++ b/drivers/pmdomain/st/ste-ux500-pm-domain.c
@@ -17,6 +17,8 @@
 
 #include <dt-bindings/arm/ux500_pm_domains.h>
 
+#define NR_DOMAINS		(DOMAIN_VAPE + 1)
+
 static int pd_power_off(struct generic_pm_domain *domain)
 {
 	/*
diff --git a/include/dt-bindings/arm/ux500_pm_domains.h b/include/dt-bindings/arm/ux500_pm_domains.h
index 9bd764f0c9e6..9d94801d8b89 100644
--- a/include/dt-bindings/arm/ux500_pm_domains.h
+++ b/include/dt-bindings/arm/ux500_pm_domains.h
@@ -9,7 +9,5 @@
 
 #define DOMAIN_VAPE		0
 
-/* Number of PM domains. */
-#define NR_DOMAINS		(DOMAIN_VAPE + 1)
 
 #endif

-- 
2.55.0

[PATCH v2 03/20] dt-bindings: arm: Add the actual power domains on U8500

[Linus Walleij]

This file has been left in an unfinished state just defining
the root power domain for the U8500 SoC. Fix it up by adding
the actual existing power domains in this SoC.

The PRCMU code and old regulator driver is mentioning some
*_RET domains, this means "retention" and is a state in the
domain and not a domain of its own.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 include/dt-bindings/arm/ux500_pm_domains.h | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/include/dt-bindings/arm/ux500_pm_domains.h b/include/dt-bindings/arm/ux500_pm_domains.h
index 9d94801d8b89..f7a9fc101fb2 100644
--- a/include/dt-bindings/arm/ux500_pm_domains.h
+++ b/include/dt-bindings/arm/ux500_pm_domains.h
@@ -8,6 +8,21 @@
 #define _DT_BINDINGS_ARM_UX500_PM_DOMAINS_H
 
 #define DOMAIN_VAPE		0
+#define DOMAIN_VARM		1
+#define DOMAIN_VMODEM		2
+#define DOMAIN_VPLL		3
+#define DOMAIN_VSMPS1		4
+#define DOMAIN_VSMPS2		5
+#define DOMAIN_VSMPS3		6
+#define DOMAIN_VRF1		7
+#define DOMAIN_SVA_MMDSP	8
+#define DOMAIN_SVA_PIPE		9
+#define DOMAIN_SIA_MMDSP	10
+#define DOMAIN_SIA_PIPE		11
+#define DOMAIN_SGA		12
+#define DOMAIN_B2R2_MCDE	13
+#define DOMAIN_ESRAM_12		14
+#define DOMAIN_ESRAM_34		15
 
 
 #endif

-- 
2.55.0

[PATCH v2 04/20] dt-bindings: mfd: db8500-prcmu: Relax EPOD regulators

[Linus Walleij]

Allow the VAPE and VSMPS2 compatibility regulators to carry power-domains.

Stop requiring the EPOD regulator child nodes that are being replaced
by generic power domains.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 .../bindings/mfd/stericsson,db8500-prcmu.yaml      | 24 ++++++----------------
 1 file changed, 6 insertions(+), 18 deletions(-)

diff --git a/Documentation/devicetree/bindings/mfd/stericsson,db8500-prcmu.yaml b/Documentation/devicetree/bindings/mfd/stericsson,db8500-prcmu.yaml
index 4edd4a3bab88..ca798c3fe7c8 100644
--- a/Documentation/devicetree/bindings/mfd/stericsson,db8500-prcmu.yaml
+++ b/Documentation/devicetree/bindings/mfd/stericsson,db8500-prcmu.yaml
@@ -72,6 +72,9 @@ properties:
           main voltage domain for the chip.
         type: object
         $ref: /schemas/regulator/regulator.yaml#
+        properties:
+          power-domains:
+            maxItems: 1
         unevaluatedProperties: false
 
       db8500_varm:
@@ -104,6 +107,9 @@ properties:
           for 1.8V I/O. SMPS means System Management Power Source.
         type: object
         $ref: /schemas/regulator/regulator.yaml#
+        properties:
+          power-domains:
+            maxItems: 1
         unevaluatedProperties: false
 
       db8500_vsmps3:
@@ -208,25 +214,7 @@ properties:
     required:
       - compatible
       - db8500_vape
-      - db8500_varm
-      - db8500_vmodem
-      - db8500_vpll
-      - db8500_vsmps1
       - db8500_vsmps2
-      - db8500_vsmps3
-      - db8500_vrf1
-      - db8500_sva_mmdsp
-      - db8500_sva_mmdsp_ret
-      - db8500_sva_pipe
-      - db8500_sia_mmdsp
-      - db8500_sia_mmdsp_ret
-      - db8500_sia_pipe
-      - db8500_sga
-      - db8500_b2r2_mcde
-      - db8500_esram12
-      - db8500_esram12_ret
-      - db8500_esram34
-      - db8500_esram34_ret
 
     additionalProperties: false
 

-- 
2.55.0

[PATCH v2 05/20] dt-bindings: display: ste,mcde: Allow power domains

[Linus Walleij]

Document the MCDE power domain.

Keep the legacy EPOD regulator binding unchanged for now.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/display/ste,mcde.yaml | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/Documentation/devicetree/bindings/display/ste,mcde.yaml b/Documentation/devicetree/bindings/display/ste,mcde.yaml
index 7a12d0b817e6..05e7e4ebc882 100644
--- a/Documentation/devicetree/bindings/display/ste,mcde.yaml
+++ b/Documentation/devicetree/bindings/display/ste,mcde.yaml
@@ -35,6 +35,9 @@ properties:
   resets:
     maxItems: 1
 
+  power-domains:
+    maxItems: 1
+
   epod-supply:
     description: a phandle to the EPOD regulator
 
@@ -109,6 +112,7 @@ examples:
   - |
     #include <dt-bindings/interrupt-controller/irq.h>
     #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/arm/ux500_pm_domains.h>
     #include <dt-bindings/mfd/dbx500-prcmu.h>
     #include <dt-bindings/gpio/gpio.h>
 
@@ -116,6 +120,7 @@ examples:
       compatible = "ste,mcde";
       reg = <0xa0350000 0x1000>;
       interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+      power-domains = <&pm_domains DOMAIN_B2R2_MCDE>;
       epod-supply = <&db8500_b2r2_mcde_reg>;
       vana-supply = <&ab8500_ldo_ana_reg>;
       clocks = <&prcmu_clk PRCMU_MCDECLK>,

-- 
2.55.0

[PATCH v2 06/20] pmdomain: st: ux500: Implement more power domains

[Linus Walleij]

This starts to implement the power domains that are just skeleton
implementations right now.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 drivers/pmdomain/st/ste-ux500-pm-domain.c | 127 +++++++++++++++++++++++++++++-
 1 file changed, 125 insertions(+), 2 deletions(-)

diff --git a/drivers/pmdomain/st/ste-ux500-pm-domain.c b/drivers/pmdomain/st/ste-ux500-pm-domain.c
index c9129a3b1805..d90a563cd6f3 100644
--- a/drivers/pmdomain/st/ste-ux500-pm-domain.c
+++ b/drivers/pmdomain/st/ste-ux500-pm-domain.c
@@ -17,7 +17,7 @@
 
 #include <dt-bindings/arm/ux500_pm_domains.h>
 
-#define NR_DOMAINS		(DOMAIN_VAPE + 1)
+#define NR_DOMAINS		(DOMAIN_ESRAM_34 + 1)
 
 static int pd_power_off(struct generic_pm_domain *domain)
 {
@@ -43,14 +43,137 @@ static int pd_power_on(struct generic_pm_domain *domain)
 	return 0;
 }
 
+/*
+ * Apart from these voltage domains there is also VSAFE which is always
+ * on. Vape_esram0_pwr for eSRAM0 is connected to VSAFE.
+ */
 static struct generic_pm_domain ux500_pm_domain_vape = {
-	.name = "VAPE",
+	/* Vape_pwr */
+	.name = "VAPE",  /* 0.95 .. 1.20 V */
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_varm = {
+	.name = "VARM",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_vmodem = {
+	.name = "VMODEM",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_vpll = {
+	.name = "VPLL", /* 1.8 V */
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+/*
+ * CHECKME: as these are used directly by peripherals as regulators,
+ * perhaps they should stay in the regulator subsystem?
+ */
+static struct generic_pm_domain ux500_pm_domain_vsmps1 = {
+	.name = "VSMPS1", /* Also called VIO (1.2V) */
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_vsmps2 = {
+	.name = "VSMPS2", /* Also called VIO (1.8V) */
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_vsmps3 = {
+	.name = "VSMPS3",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_vrf1 = {
+	.name = "VRF1",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+/* The following are technically children of VAPE */
+static struct generic_pm_domain ux500_pm_domain_sva_mmdsp = {
+	/* Vape_SVA_MMDSP_pwr */
+	.name = "SVA_MMDSP",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_sva_pipe = {
+	/* Vape_SVA_pwr */
+	.name = "SVA_PIPE",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_sia_mmdsp = {
+	/* Vape_SIA_MMDSP_pwr */
+	.name = "SIA_MMDSP",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_sia_pipe = {
+	/* Vape_SIA_pwr */
+	.name = "SIA_PIPE",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_sga = {
+	/* Vape_SGA_pwr */
+	.name = "SGA",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_b2r2_mcde = {
+	/* Vape_DSS_pwr DSS (display subsystem) */
+	.name = "B2R2_MCDE",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_esram_12 = {
+	/* Vape_esram1_pwr, Vape_esram2_pwr */
+	.name = "ESRAM_12",
+	.power_off = pd_power_off,
+	.power_on = pd_power_on,
+};
+
+static struct generic_pm_domain ux500_pm_domain_esram_34 = {
+	/* Vape_esram3_pwr, Vape_esram4_pwr */
+	.name = "ESRAM_34",
 	.power_off = pd_power_off,
 	.power_on = pd_power_on,
 };
 
 static struct generic_pm_domain *ux500_pm_domains[NR_DOMAINS] = {
 	[DOMAIN_VAPE] = &ux500_pm_domain_vape,
+	[DOMAIN_VARM] = &ux500_pm_domain_varm,
+	[DOMAIN_VMODEM] = &ux500_pm_domain_vmodem,
+	[DOMAIN_VPLL] = &ux500_pm_domain_vpll,
+	[DOMAIN_VSMPS1] = &ux500_pm_domain_vsmps1,
+	[DOMAIN_VSMPS2] = &ux500_pm_domain_vsmps2,
+	[DOMAIN_VSMPS3] = &ux500_pm_domain_vsmps3,
+	[DOMAIN_VRF1] = &ux500_pm_domain_vrf1,
+	[DOMAIN_SVA_MMDSP] = &ux500_pm_domain_sva_mmdsp,
+	[DOMAIN_SVA_PIPE] = &ux500_pm_domain_sva_pipe,
+	[DOMAIN_SIA_MMDSP] = &ux500_pm_domain_sia_mmdsp,
+	[DOMAIN_SIA_PIPE] = &ux500_pm_domain_sia_pipe,
+	[DOMAIN_SGA] = &ux500_pm_domain_sga,
+	[DOMAIN_B2R2_MCDE] = &ux500_pm_domain_b2r2_mcde,
+	[DOMAIN_ESRAM_12] = &ux500_pm_domain_esram_12,
+	[DOMAIN_ESRAM_34] = &ux500_pm_domain_esram_34,
 };
 
 static const struct of_device_id ux500_pm_domain_matches[] = {

-- 
2.55.0

[PATCH v2 07/20] ARM: dts: ux500: Rename power domains node

[Linus Walleij]

This matches the naming used in the binding document
Documentation/devicetree/bindings/power/power-domain.yaml
It's most logical to call it a power controller.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 arch/arm/boot/dts/st/ste-dbx5x0.dtsi | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
index 25a20fafc6b9..11fcae1904e2 100644
--- a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
@@ -343,7 +343,7 @@ pmu {
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
 		};
 
-		pm_domains: pm_domains0 {
+		pm_domains: power-controller {
 			compatible = "stericsson,ux500-pm-domains";
 			#power-domain-cells = <1>;
 		};

-- 
2.55.0

[PATCH v2 08/20] dt-bindings: cache: l2c2x0: Document power domain

[Linus Walleij]

Describe the optional power domain for cache controllers.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/cache/l2c2x0.yaml | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/Documentation/devicetree/bindings/cache/l2c2x0.yaml b/Documentation/devicetree/bindings/cache/l2c2x0.yaml
index ee604117ffb3..4e568c2a34ef 100644
--- a/Documentation/devicetree/bindings/cache/l2c2x0.yaml
+++ b/Documentation/devicetree/bindings/cache/l2c2x0.yaml
@@ -68,6 +68,8 @@ properties:
 
   power-domains:
     maxItems: 1
+    description:
+      Power domain controlling the cache controller.
 
   arm,data-latency:
     description: Cycles of latency for Data RAM accesses. Specifies 3 cells of

-- 
2.55.0

[PATCH v2 09/20] dt-bindings: arm: pmu: Allow power domains

[Linus Walleij]

Allow ARM PMU nodes to reference their power domain.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/arm/pmu.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/arm/pmu.yaml b/Documentation/devicetree/bindings/arm/pmu.yaml
index f47baaefcdac..305c1a9668f4 100644
--- a/Documentation/devicetree/bindings/arm/pmu.yaml
+++ b/Documentation/devicetree/bindings/arm/pmu.yaml
@@ -88,6 +88,9 @@ properties:
     # Don't know how many CPUs, so no constraints to specify
     description: 1 per-cpu interrupt (PPI) or 1 interrupt per core.
 
+  power-domains:
+    maxItems: 1
+
   interrupt-affinity:
     $ref: /schemas/types.yaml#/definitions/phandle-array
     items:

-- 
2.55.0

[PATCH v2 10/20] dt-bindings: clock: stericsson,u8500-clks: Allow power domains

[Linus Walleij]

Allow the DB8500 clock controller node to reference its power domain.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/clock/stericsson,u8500-clks.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/clock/stericsson,u8500-clks.yaml b/Documentation/devicetree/bindings/clock/stericsson,u8500-clks.yaml
index 4ebfa5a8d524..75e5e1107ebb 100644
--- a/Documentation/devicetree/bindings/clock/stericsson,u8500-clks.yaml
+++ b/Documentation/devicetree/bindings/clock/stericsson,u8500-clks.yaml
@@ -34,6 +34,9 @@ properties:
       - description: PRCC 5 register area
       - description: PRCC 6 register area
 
+  power-domains:
+    maxItems: 1
+
   prcmu-clock:
     description: A subnode with one clock cell for PRCMU (power, reset, control
       management unit) clocks. The cell indicates which PRCMU clock in the

-- 
2.55.0

[PATCH v2 11/20] dt-bindings: timer: arm,twd-timer: Allow power domains

[Linus Walleij]

Allow TWD timer nodes to reference their power domain.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/timer/arm,twd-timer.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/timer/arm,twd-timer.yaml b/Documentation/devicetree/bindings/timer/arm,twd-timer.yaml
index eb1127352c7b..716d5f2d4eac 100644
--- a/Documentation/devicetree/bindings/timer/arm,twd-timer.yaml
+++ b/Documentation/devicetree/bindings/timer/arm,twd-timer.yaml
@@ -33,6 +33,9 @@ properties:
   clocks:
     maxItems: 1
 
+  power-domains:
+    maxItems: 1
+
   always-on:
     description:
       If present, the timer is powered through an always-on power domain,

-- 
2.55.0

[PATCH v2 12/20] dt-bindings: watchdog: arm,twd-wdt: Allow power domains

[Linus Walleij]

Allow TWD watchdog nodes to reference their power domain.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/watchdog/arm,twd-wdt.yaml | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/watchdog/arm,twd-wdt.yaml b/Documentation/devicetree/bindings/watchdog/arm,twd-wdt.yaml
index 9646ac72051e..5f6a9d6b9976 100644
--- a/Documentation/devicetree/bindings/watchdog/arm,twd-wdt.yaml
+++ b/Documentation/devicetree/bindings/watchdog/arm,twd-wdt.yaml
@@ -33,6 +33,9 @@ properties:
   clocks:
     maxItems: 1
 
+  power-domains:
+    maxItems: 1
+
 required:
   - compatible
   - reg

-- 
2.55.0

[PATCH v2 13/20] ARM: dts: ux500: Add power domains

[Linus Walleij]

Add the actual power domains to all the SoC peripherals.

Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 arch/arm/boot/dts/st/ste-dbx5x0.dtsi | 70 +++++++++++++++++++++++++++++++-----
 1 file changed, 61 insertions(+), 9 deletions(-)

diff --git a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
index 11fcae1904e2..afba6bee42af 100644
--- a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
@@ -154,6 +154,7 @@ sram@40020000 {
 			reg = <0x40020000 0x40000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+			power-domains = <&pm_domains DOMAIN_ESRAM_12>;
 			ranges = <0 0x40020000 0x40000>;
 		};
 		sram@40060000 {
@@ -162,6 +163,7 @@ sram@40060000 {
 			reg = <0x40060000 0x40000>;
 			#address-cells = <1>;
 			#size-cells = <1>;
+			power-domains = <&pm_domains DOMAIN_ESRAM_34>;
 			ranges = <0 0x40060000 0x40000>;
 
 			lcla: sram@20000 {
@@ -181,7 +183,7 @@ lcla: sram@20000 {
 		ptm@801ae000 {
 			compatible = "arm,coresight-etm3x", "arm,primecell";
 			reg = <0x801ae000 0x1000>;
-
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
 			clock-names = "apb_pclk", "atclk";
 			cpu = <&CPU0>;
@@ -197,7 +199,7 @@ ptm0_out_port: endpoint {
 		ptm@801af000 {
 			compatible = "arm,coresight-etm3x", "arm,primecell";
 			reg = <0x801af000 0x1000>;
-
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
 			clock-names = "apb_pclk", "atclk";
 			cpu = <&CPU1>;
@@ -213,7 +215,7 @@ ptm1_out_port: endpoint {
 		funnel@801a6000 {
 			compatible = "arm,coresight-dynamic-funnel", "arm,primecell";
 			reg = <0x801a6000 0x1000>;
-
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
 			clock-names = "apb_pclk", "atclk";
 			out-ports {
@@ -249,6 +251,7 @@ replicator {
 			compatible = "arm,coresight-static-replicator";
 			clocks = <&prcmu_clk PRCMU_APEATCLK>;
 			clock-names = "atclk";
+			power-domains = <&pm_domains DOMAIN_VARM>;
 
 			out-ports {
 				#address-cells = <1>;
@@ -280,7 +283,7 @@ replicator_in_port0: endpoint {
 		tpiu@80190000 {
 			compatible = "arm,coresight-tpiu", "arm,primecell";
 			reg = <0x80190000 0x1000>;
-
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
 			clock-names = "apb_pclk", "atclk";
 			in-ports {
@@ -295,7 +298,7 @@ tpiu_in_port: endpoint {
 		etb@801a4000 {
 			compatible = "arm,coresight-etb10", "arm,primecell";
 			reg = <0x801a4000 0x1000>;
-
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&prcmu_clk PRCMU_APETRACECLK>, <&prcmu_clk PRCMU_APEATCLK>;
 			clock-names = "apb_pclk", "atclk";
 			in-ports {
@@ -314,11 +317,13 @@ intc: interrupt-controller@a0411000 {
 			interrupt-controller;
 			reg = <0xa0411000 0x1000>,
 			      <0xa0410100 0x100>;
+			power-domains = <&pm_domains DOMAIN_VARM>;
 		};
 
 		scu@a0410000 {
 			compatible = "arm,cortex-a9-scu";
 			reg = <0xa0410000 0x100>;
+			power-domains = <&pm_domains DOMAIN_VARM>;
 		};
 
 		/*
@@ -326,6 +331,7 @@ scu@a0410000 {
 		 * and various things like spin tables
 		 */
 		backupram@80150000 {
+			/* This memory is in the VSAFE (always on) power domain */
 			compatible = "ste,dbx500-backupram";
 			reg = <0x80150000 0x2000>;
 		};
@@ -334,6 +340,7 @@ L2: cache-controller {
 			compatible = "arm,pl310-cache";
 			reg = <0xa0412000 0x1000>;
 			interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			cache-unified;
 			cache-level = <2>;
 		};
@@ -341,11 +348,24 @@ L2: cache-controller {
 		pmu {
 			compatible = "arm,cortex-a9-pmu";
 			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&pm_domains DOMAIN_VARM>;
 		};
 
 		pm_domains: power-controller {
 			compatible = "stericsson,ux500-pm-domains";
 			#power-domain-cells = <1>;
+			power-domains = <&pm_domains DOMAIN_VAPE>,
+					<&pm_domains DOMAIN_VAPE>,
+					<&pm_domains DOMAIN_VAPE>,
+					<&pm_domains DOMAIN_VAPE>,
+					<&pm_domains DOMAIN_VAPE>,
+					<&pm_domains DOMAIN_VAPE>;
+			power-domains-child-ids = <DOMAIN_SVA_MMDSP>,
+						 <DOMAIN_SVA_PIPE>,
+						 <DOMAIN_SIA_MMDSP>,
+						 <DOMAIN_SIA_PIPE>,
+						 <DOMAIN_SGA>,
+						 <DOMAIN_B2R2_MCDE>;
 		};
 
 		clocks {
@@ -357,6 +377,7 @@ clocks {
 			reg = <0x8012f000 0x1000>, <0x8011f000 0x1000>,
 			    <0x8000f000 0x1000>, <0xa03ff000 0x1000>,
 			    <0xa03cf000 0x1000>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			prcmu_clk: prcmu-clock {
 				#clock-cells = <1>;
@@ -393,7 +414,7 @@ mtu@a03c6000 {
 			compatible = "st,nomadik-mtu";
 			reg = <0xa03c6000 0x1000>;
 			interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH>;
-
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 			clocks = <&prcmu_clk PRCMU_TIMCLK>, <&prcc_pclk 6 6>;
 			clock-names = "timclk", "apb_pclk";
 		};
@@ -402,7 +423,7 @@ timer@a0410600 {
 			compatible = "arm,cortex-a9-twd-timer";
 			reg = <0xa0410600 0x20>;
 			interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
-
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&smp_twd_clk>;
 		};
 
@@ -410,14 +431,15 @@ watchdog@a0410620 {
 			compatible = "arm,cortex-a9-twd-wdt";
 			reg = <0xa0410620 0x20>;
 			interrupts = <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>;
+			power-domains = <&pm_domains DOMAIN_VARM>;
 			clocks = <&smp_twd_clk>;
 		};
 
 		rtc@80154000 {
+			/* This peripheral is in the VSAFE (always on) power domain */
 			compatible = "arm,pl031", "arm,primecell";
 			reg = <0x80154000 0x1000>;
 			interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
-
 			clocks = <&rtc_clk>;
 			clock-names = "apb_pclk";
 		};
@@ -435,6 +457,7 @@ gpio0: gpio@8012e000 {
 			gpio-bank = <0>;
 			gpio-ranges = <&pinctrl 0 0 32>;
 			clocks = <&prcc_pclk 1 9>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio1: gpio@8012e080 {
@@ -450,6 +473,7 @@ gpio1: gpio@8012e080 {
 			gpio-bank = <1>;
 			gpio-ranges = <&pinctrl 0 32 5>;
 			clocks = <&prcc_pclk 1 9>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio2: gpio@8000e000 {
@@ -465,6 +489,7 @@ gpio2: gpio@8000e000 {
 			gpio-bank = <2>;
 			gpio-ranges = <&pinctrl 0 64 32>;
 			clocks = <&prcc_pclk 3 8>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio3: gpio@8000e080 {
@@ -480,6 +505,7 @@ gpio3: gpio@8000e080 {
 			gpio-bank = <3>;
 			gpio-ranges = <&pinctrl 0 96 2>;
 			clocks = <&prcc_pclk 3 8>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio4: gpio@8000e100 {
@@ -495,6 +521,7 @@ gpio4: gpio@8000e100 {
 			gpio-bank = <4>;
 			gpio-ranges = <&pinctrl 0 128 32>;
 			clocks = <&prcc_pclk 3 8>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio5: gpio@8000e180 {
@@ -510,6 +537,7 @@ gpio5: gpio@8000e180 {
 			gpio-bank = <5>;
 			gpio-ranges = <&pinctrl 0 160 12>;
 			clocks = <&prcc_pclk 3 8>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio6: gpio@8011e000 {
@@ -525,6 +553,7 @@ gpio6: gpio@8011e000 {
 			gpio-bank = <6>;
 			gpio-ranges = <&pinctrl 0 192 32>;
 			clocks = <&prcc_pclk 2 11>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio7: gpio@8011e080 {
@@ -540,6 +569,7 @@ gpio7: gpio@8011e080 {
 			gpio-bank = <7>;
 			gpio-ranges = <&pinctrl 0 224 7>;
 			clocks = <&prcc_pclk 2 11>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		gpio8: gpio@a03fe000 {
@@ -555,6 +585,7 @@ gpio8: gpio@a03fe000 {
 			gpio-bank = <8>;
 			gpio-ranges = <&pinctrl 0 256 12>;
 			clocks = <&prcc_pclk 5 1>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		pinctrl: pinctrl {
@@ -570,6 +601,7 @@ usb_per5@a03e0000 {
 			reg = <0xa03e0000 0x10000>;
 			interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>;
 			interrupt-names = "mc";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			dr_mode = "otg";
 
@@ -613,9 +645,11 @@ dma: dma-controller@801C0000 {
 			memcpy-channels = <56 57 58 59 60>;
 
 			clocks = <&prcmu_clk PRCMU_DMACLK>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		prcmu: prcmu@80157000 {
+			/* This peripheral is in the VSAFE (always on) power domain */
 			compatible = "stericsson,db8500-prcmu", "syscon";
 			reg = <0x80157000 0x2000>, <0x801b0000 0x8000>, <0x801b8000 0x1000>;
 			reg-names = "prcmu", "prcmu-tcpm", "prcmu-tcdm";
@@ -641,6 +675,10 @@ thermal: thermal@801573c0 {
 				#thermal-sensor-cells = <0>;
 			};
 
+			/*
+			 * TODO: Delete these bogus regulators and replace with power
+			 * domains.
+			 */
 			db8500-prcmu-regulators {
 				compatible = "stericsson,db8500-prcmu-regulator";
 
@@ -932,6 +970,7 @@ serial0: serial@80120000 {
 
 			clocks = <&prcc_kclk 1 0>, <&prcc_pclk 1 0>;
 			clock-names = "uart", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART0>;
 
 			status = "disabled";
@@ -948,6 +987,7 @@ serial1: serial@80121000 {
 
 			clocks = <&prcc_kclk 1 1>, <&prcc_pclk 1 1>;
 			clock-names = "uart", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 			resets = <&prcc_reset DB8500_PRCC_1 DB8500_PRCC_1_RESET_UART1>;
 
 			status = "disabled";
@@ -964,6 +1004,7 @@ serial2: serial@80007000 {
 
 			clocks = <&prcc_kclk 3 6>, <&prcc_pclk 3 6>;
 			clock-names = "uart", "apb_pclk";
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 			resets = <&prcc_reset DB8500_PRCC_3 DB8500_PRCC_3_RESET_UART2>;
 
 			status = "disabled";
@@ -1080,7 +1121,9 @@ msp0: msp@80123000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80123000 0x1000>;
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
+			/* TODO: delete and replace with power-domain handling */
 			v-ape-supply = <&db8500_vape_reg>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			dmas = <&dma 31 0 0x12>, /* Logical - DevToMem - HighPrio */
 			       <&dma 31 0 0x10>; /* Logical - MemToDev - HighPrio */
@@ -1097,7 +1140,9 @@ msp1: msp@80124000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80124000 0x1000>;
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			/* TODO: delete and replace with power-domain handling */
 			v-ape-supply = <&db8500_vape_reg>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			/* This DMA channel only exist on DB8500 v1 */
 			dmas = <&dma 30 0 0x10>; /* Logical - MemToDev - HighPrio */
@@ -1115,7 +1160,9 @@ msp2: msp@80117000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80117000 0x1000>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
+			/* TODO: delete and replace with power-domain handling */
 			v-ape-supply = <&db8500_vape_reg>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			dmas = <&dma 14 0 0x12>, /* Logical  - DevToMem - HighPrio */
 			       <&dma 14 1 0x19>; /* Physical Chan 1 - MemToDev
@@ -1133,7 +1180,9 @@ msp3: msp@80125000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80125000 0x1000>;
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
+			/* TODO: delete and replace with power-domain handling */
 			v-ape-supply = <&db8500_vape_reg>;
+			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			/* This DMA channel only exist on DB8500 v2 */
 			dmas = <&dma 30 0 0x12>; /* Logical - DevToMem - HighPrio */
@@ -1175,14 +1224,17 @@ gpu@a0300000 {
 					  "combined";
 			clocks = <&prcmu_clk PRCMU_ACLK>, <&prcmu_clk PRCMU_SGACLK>;
 			clock-names = "bus", "core";
+			power-domains = <&pm_domains DOMAIN_SGA>;
+			/* TODO: delete and replace with power-domain handling */
 			mali-supply = <&db8500_sga_reg>;
-			power-domains = <&pm_domains DOMAIN_VAPE>;
 		};
 
 		mcde@a0350000 {
 			compatible = "ste,mcde";
 			reg = <0xa0350000 0x1000>;
 			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
+			power-domains = <&pm_domains DOMAIN_B2R2_MCDE>;
+			/* TODO: delete and replace with power-domain handling */
 			epod-supply = <&db8500_b2r2_mcde_reg>;
 			clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
 				 <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */

-- 
2.55.0

[PATCH v2 14/20] pmdomain: st: ux500: Control DB8500 EPODs

[Linus Walleij]

Move the DB8500 EPOD state handling into the Ux500 power-domain driver.

Keep the old regulator driver mutually exclusive with the pmdomain driver.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 arch/arm/mach-ux500/Kconfig               |   2 +-
 drivers/pmdomain/st/ste-ux500-pm-domain.c | 355 +++++++++++++++++++++---------
 drivers/regulator/Kconfig                 |   1 +
 3 files changed, 254 insertions(+), 104 deletions(-)

diff --git a/arch/arm/mach-ux500/Kconfig b/arch/arm/mach-ux500/Kconfig
index c18def269137..56636c993f49 100644
--- a/arch/arm/mach-ux500/Kconfig
+++ b/arch/arm/mach-ux500/Kconfig
@@ -26,7 +26,7 @@ menuconfig ARCH_U8500
 	select PL310_ERRATA_753970 if CACHE_L2X0
 	select PM_GENERIC_DOMAINS if PM
 	select REGULATOR
-	select REGULATOR_DB8500_PRCMU
+	select UX500_PM_DOMAIN
 	select REGULATOR_FIXED_VOLTAGE
 	select SOC_BUS
 	select RESET_CONTROLLER
diff --git a/drivers/pmdomain/st/ste-ux500-pm-domain.c b/drivers/pmdomain/st/ste-ux500-pm-domain.c
index d90a563cd6f3..b31a36a4acd1 100644
--- a/drivers/pmdomain/st/ste-ux500-pm-domain.c
+++ b/drivers/pmdomain/st/ste-ux500-pm-domain.c
@@ -6,174 +6,292 @@
  *
  * Implements PM domains using the generic PM domain for ux500.
  */
+#include <linux/cleanup.h>
 #include <linux/device.h>
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/printk.h>
-#include <linux/slab.h>
 #include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/mfd/db8500-prcmu.h>
+#include <linux/mutex.h>
 #include <linux/of.h>
+#include <linux/platform_device.h>
 #include <linux/pm_domain.h>
+#include <linux/slab.h>
 
 #include <dt-bindings/arm/ux500_pm_domains.h>
 
 #define NR_DOMAINS		(DOMAIN_ESRAM_34 + 1)
+#define UX500_EPOD_NONE		NUM_EPOD_ID
 
-static int pd_power_off(struct generic_pm_domain *domain)
+/**
+ * struct dbx500_powerdomain_info - dbx500 power domain information
+ * @genpd: generic power domain
+ * @epod_id: id for EPOD (power domain)
+ * @is_ramret: RAM retention switch for EPOD (power domain)
+ */
+struct dbx500_powerdomain_info {
+	struct generic_pm_domain genpd;
+	u16 epod_id;
+	bool is_ramret;
+};
+
+static DEFINE_MUTEX(ux500_pd_lock);
+static bool epod_on[NUM_EPOD_ID];
+static bool epod_ramret[NUM_EPOD_ID];
+
+static int enable_epod(u16 epod_id, bool ramret)
 {
-	/*
-	 * Handle the gating of the PM domain regulator here.
-	 *
-	 * Drivers/subsystems handling devices in the PM domain needs to perform
-	 * register context save/restore from their respective runtime PM
-	 * callbacks, to be able to enable PM domain gating/ungating.
-	 */
+	int ret;
+
+	if (ramret) {
+		if (!epod_on[epod_id]) {
+			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_RAMRET);
+			if (ret < 0)
+				return ret;
+		}
+		epod_ramret[epod_id] = true;
+	} else {
+		ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_ON);
+		if (ret < 0)
+			return ret;
+		epod_on[epod_id] = true;
+	}
+
 	return 0;
 }
 
-static int pd_power_on(struct generic_pm_domain *domain)
+static int disable_epod(u16 epod_id, bool ramret)
 {
-	/*
-	 * Handle the ungating of the PM domain regulator here.
-	 *
-	 * Drivers/subsystems handling devices in the PM domain needs to perform
-	 * register context save/restore from their respective runtime PM
-	 * callbacks, to be able to enable PM domain gating/ungating.
-	 */
+	int ret;
+
+	if (ramret) {
+		if (!epod_on[epod_id]) {
+			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_OFF);
+			if (ret < 0)
+				return ret;
+		}
+		epod_ramret[epod_id] = false;
+	} else {
+		if (epod_ramret[epod_id]) {
+			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_RAMRET);
+			if (ret < 0)
+				return ret;
+		} else {
+			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_OFF);
+			if (ret < 0)
+				return ret;
+		}
+		epod_on[epod_id] = false;
+	}
+
 	return 0;
 }
 
+
+static int pd_power_off(struct generic_pm_domain *domain)
+{
+	struct dbx500_powerdomain_info *info =
+		container_of(domain, struct dbx500_powerdomain_info, genpd);
+	int ret = 0;
+
+	guard(mutex)(&ux500_pd_lock);
+	if (info->epod_id < NUM_EPOD_ID)
+		ret = disable_epod(info->epod_id, info->is_ramret);
+
+	return ret;
+}
+
+static int pd_power_on(struct generic_pm_domain *domain)
+{
+	struct dbx500_powerdomain_info *info =
+		container_of(domain, struct dbx500_powerdomain_info, genpd);
+	int ret = 0;
+
+	guard(mutex)(&ux500_pd_lock);
+	if (info->epod_id < NUM_EPOD_ID)
+		ret = enable_epod(info->epod_id, info->is_ramret);
+
+	return ret;
+}
+
 /*
  * Apart from these voltage domains there is also VSAFE which is always
  * on. Vape_esram0_pwr for eSRAM0 is connected to VSAFE.
  */
-static struct generic_pm_domain ux500_pm_domain_vape = {
+static struct dbx500_powerdomain_info ux500_pm_domain_vape = {
 	/* Vape_pwr */
-	.name = "VAPE",  /* 0.95 .. 1.20 V */
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "VAPE",  /* 0.95 .. 1.20 V */
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_varm = {
-	.name = "VARM",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_varm = {
+	.genpd = {
+		.name = "VARM",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_vmodem = {
-	.name = "VMODEM",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_vmodem = {
+	.genpd = {
+		.name = "VMODEM",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_vpll = {
-	.name = "VPLL", /* 1.8 V */
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_vpll = {
+	.genpd = {
+		.name = "VPLL", /* 1.8 V */
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
 /*
  * CHECKME: as these are used directly by peripherals as regulators,
  * perhaps they should stay in the regulator subsystem?
  */
-static struct generic_pm_domain ux500_pm_domain_vsmps1 = {
-	.name = "VSMPS1", /* Also called VIO (1.2V) */
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_vsmps1 = {
+	.genpd = {
+		.name = "VSMPS1", /* Also called VIO (1.2V) */
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_vsmps2 = {
-	.name = "VSMPS2", /* Also called VIO (1.8V) */
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_vsmps2 = {
+	.genpd = {
+		.name = "VSMPS2", /* Also called VIO (1.8V) */
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_vsmps3 = {
-	.name = "VSMPS3",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_vsmps3 = {
+	.genpd = {
+		.name = "VSMPS3",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_vrf1 = {
-	.name = "VRF1",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+static struct dbx500_powerdomain_info ux500_pm_domain_vrf1 = {
+	.genpd = {
+		.name = "VRF1",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = UX500_EPOD_NONE,
 };
 
 /* The following are technically children of VAPE */
-static struct generic_pm_domain ux500_pm_domain_sva_mmdsp = {
+static struct dbx500_powerdomain_info ux500_pm_domain_sva_mmdsp = {
 	/* Vape_SVA_MMDSP_pwr */
-	.name = "SVA_MMDSP",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "SVA_MMDSP",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_SVAMMDSP,
 };
 
-static struct generic_pm_domain ux500_pm_domain_sva_pipe = {
+static struct dbx500_powerdomain_info ux500_pm_domain_sva_pipe = {
 	/* Vape_SVA_pwr */
-	.name = "SVA_PIPE",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "SVA_PIPE",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_SVAPIPE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_sia_mmdsp = {
+static struct dbx500_powerdomain_info ux500_pm_domain_sia_mmdsp = {
 	/* Vape_SIA_MMDSP_pwr */
-	.name = "SIA_MMDSP",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "SIA_MMDSP",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_SIAMMDSP,
 };
 
-static struct generic_pm_domain ux500_pm_domain_sia_pipe = {
+static struct dbx500_powerdomain_info ux500_pm_domain_sia_pipe = {
 	/* Vape_SIA_pwr */
-	.name = "SIA_PIPE",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "SIA_PIPE",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_SIAPIPE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_sga = {
+static struct dbx500_powerdomain_info ux500_pm_domain_sga = {
 	/* Vape_SGA_pwr */
-	.name = "SGA",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "SGA",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_SGA,
 };
 
-static struct generic_pm_domain ux500_pm_domain_b2r2_mcde = {
+static struct dbx500_powerdomain_info ux500_pm_domain_b2r2_mcde = {
 	/* Vape_DSS_pwr DSS (display subsystem) */
-	.name = "B2R2_MCDE",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "B2R2_MCDE",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_B2R2_MCDE,
 };
 
-static struct generic_pm_domain ux500_pm_domain_esram_12 = {
+static struct dbx500_powerdomain_info ux500_pm_domain_esram_12 = {
 	/* Vape_esram1_pwr, Vape_esram2_pwr */
-	.name = "ESRAM_12",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "ESRAM_12",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_ESRAM12,
 };
 
-static struct generic_pm_domain ux500_pm_domain_esram_34 = {
+static struct dbx500_powerdomain_info ux500_pm_domain_esram_34 = {
 	/* Vape_esram3_pwr, Vape_esram4_pwr */
-	.name = "ESRAM_34",
-	.power_off = pd_power_off,
-	.power_on = pd_power_on,
+	.genpd = {
+		.name = "ESRAM_34",
+		.power_off = pd_power_off,
+		.power_on = pd_power_on,
+	},
+	.epod_id = EPOD_ID_ESRAM34,
 };
 
 static struct generic_pm_domain *ux500_pm_domains[NR_DOMAINS] = {
-	[DOMAIN_VAPE] = &ux500_pm_domain_vape,
-	[DOMAIN_VARM] = &ux500_pm_domain_varm,
-	[DOMAIN_VMODEM] = &ux500_pm_domain_vmodem,
-	[DOMAIN_VPLL] = &ux500_pm_domain_vpll,
-	[DOMAIN_VSMPS1] = &ux500_pm_domain_vsmps1,
-	[DOMAIN_VSMPS2] = &ux500_pm_domain_vsmps2,
-	[DOMAIN_VSMPS3] = &ux500_pm_domain_vsmps3,
-	[DOMAIN_VRF1] = &ux500_pm_domain_vrf1,
-	[DOMAIN_SVA_MMDSP] = &ux500_pm_domain_sva_mmdsp,
-	[DOMAIN_SVA_PIPE] = &ux500_pm_domain_sva_pipe,
-	[DOMAIN_SIA_MMDSP] = &ux500_pm_domain_sia_mmdsp,
-	[DOMAIN_SIA_PIPE] = &ux500_pm_domain_sia_pipe,
-	[DOMAIN_SGA] = &ux500_pm_domain_sga,
-	[DOMAIN_B2R2_MCDE] = &ux500_pm_domain_b2r2_mcde,
-	[DOMAIN_ESRAM_12] = &ux500_pm_domain_esram_12,
-	[DOMAIN_ESRAM_34] = &ux500_pm_domain_esram_34,
+	[DOMAIN_VAPE] = &ux500_pm_domain_vape.genpd,
+	[DOMAIN_VARM] = &ux500_pm_domain_varm.genpd,
+	[DOMAIN_VMODEM] = &ux500_pm_domain_vmodem.genpd,
+	[DOMAIN_VPLL] = &ux500_pm_domain_vpll.genpd,
+	[DOMAIN_VSMPS1] = &ux500_pm_domain_vsmps1.genpd,
+	[DOMAIN_VSMPS2] = &ux500_pm_domain_vsmps2.genpd,
+	[DOMAIN_VSMPS3] = &ux500_pm_domain_vsmps3.genpd,
+	[DOMAIN_VRF1] = &ux500_pm_domain_vrf1.genpd,
+	[DOMAIN_SVA_MMDSP] = &ux500_pm_domain_sva_mmdsp.genpd,
+	[DOMAIN_SVA_PIPE] = &ux500_pm_domain_sva_pipe.genpd,
+	[DOMAIN_SIA_MMDSP] = &ux500_pm_domain_sia_mmdsp.genpd,
+	[DOMAIN_SIA_PIPE] = &ux500_pm_domain_sia_pipe.genpd,
+	[DOMAIN_SGA] = &ux500_pm_domain_sga.genpd,
+	[DOMAIN_B2R2_MCDE] = &ux500_pm_domain_b2r2_mcde.genpd,
+	[DOMAIN_ESRAM_12] = &ux500_pm_domain_esram_12.genpd,
+	[DOMAIN_ESRAM_34] = &ux500_pm_domain_esram_34.genpd,
 };
 
 static const struct of_device_id ux500_pm_domain_matches[] = {
@@ -186,11 +304,12 @@ static int ux500_pm_domains_probe(struct platform_device *pdev)
 	struct device_node *np = pdev->dev.of_node;
 	struct genpd_onecell_data *genpd_data;
 	int i;
+	int ret;
 
 	if (!np)
 		return -ENODEV;
 
-	genpd_data = kzalloc_obj(*genpd_data);
+	genpd_data = devm_kzalloc(&pdev->dev, sizeof(*genpd_data), GFP_KERNEL);
 	if (!genpd_data)
 		return -ENOMEM;
 
@@ -198,14 +317,44 @@ static int ux500_pm_domains_probe(struct platform_device *pdev)
 	genpd_data->num_domains = ARRAY_SIZE(ux500_pm_domains);
 
 	for (i = 0; i < ARRAY_SIZE(ux500_pm_domains); ++i)
-		pm_genpd_init(ux500_pm_domains[i], NULL, false);
+		pm_genpd_init(ux500_pm_domains[i], NULL, true);
+
+	ret = of_genpd_add_provider_onecell(np, genpd_data);
+	if (ret)
+		goto remove_genpds;
+
+	ret = of_genpd_add_child_ids(np, genpd_data);
+	if (ret < 0)
+		goto del_provider;
+
+	platform_set_drvdata(pdev, genpd_data);
 
-	of_genpd_add_provider_onecell(np, genpd_data);
 	return 0;
+
+del_provider:
+	of_genpd_del_provider(np);
+remove_genpds:
+	while (i--)
+		pm_genpd_remove(ux500_pm_domains[i]);
+
+	return ret;
+}
+
+static void ux500_pm_domains_remove(struct platform_device *pdev)
+{
+	struct genpd_onecell_data *genpd_data = platform_get_drvdata(pdev);
+	int i;
+
+	of_genpd_remove_child_ids(pdev->dev.of_node, genpd_data);
+	of_genpd_del_provider(pdev->dev.of_node);
+
+	for (i = genpd_data->num_domains - 1; i >= 0; i--)
+		pm_genpd_remove(genpd_data->domains[i]);
 }
 
 static struct platform_driver ux500_pm_domains_driver = {
 	.probe  = ux500_pm_domains_probe,
+	.remove = ux500_pm_domains_remove,
 	.driver = {
 		.name = "ux500_pm_domains",
 		.of_match_table = ux500_pm_domain_matches,
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 89789ac7a786..851e1a8fc22f 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -414,6 +414,7 @@ config REGULATOR_DBX500_PRCMU
 config REGULATOR_DB8500_PRCMU
 	bool "ST-Ericsson DB8500 Voltage Domain Regulators"
 	depends on MFD_DB8500_PRCMU
+	depends on !UX500_PM_DOMAIN
 	select REGULATOR_DBX500_PRCMU
 	help
 	  This driver supports the voltage domain regulators controlled by the

-- 
2.55.0

[PATCH v2 15/20] drm/mcde: Use power domain for display power

[Linus Walleij]

Replace explicit EPOD regulator handling with runtime PM.

Use the MCDE power domain and drop the regulator dependency.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 drivers/gpu/drm/mcde/mcde_clk_div.c |  4 +--
 drivers/gpu/drm/mcde/mcde_display.c | 11 +++---
 drivers/gpu/drm/mcde/mcde_drm.h     |  2 --
 drivers/gpu/drm/mcde/mcde_drv.c     | 68 ++++++++++++-------------------------
 drivers/gpu/drm/mcde/mcde_dsi.c     |  1 -
 5 files changed, 29 insertions(+), 57 deletions(-)

diff --git a/drivers/gpu/drm/mcde/mcde_clk_div.c b/drivers/gpu/drm/mcde/mcde_clk_div.c
index 8c5af2677357..1a22e6233946 100644
--- a/drivers/gpu/drm/mcde/mcde_clk_div.c
+++ b/drivers/gpu/drm/mcde/mcde_clk_div.c
@@ -1,7 +1,7 @@
 // SPDX-License-Identifier: GPL-2.0
 #include <linux/clk-provider.h>
 #include <linux/io.h>
-#include <linux/regulator/consumer.h>
+#include <linux/pm_runtime.h>
 
 #include "mcde_drm.h"
 #include "mcde_display_regs.h"
@@ -95,7 +95,7 @@ static unsigned long mcde_clk_div_recalc_rate(struct clk_hw *hw,
 	 * It will come up with 0 in the divider register bits, which
 	 * means "divide by 2".
 	 */
-	if (!regulator_is_enabled(mcde->epod))
+	if (!pm_runtime_active(mcde->dev))
 		return DIV_ROUND_UP_ULL(prate, 2);
 
 	cr = readl(mcde->regs + cdiv->cr);
diff --git a/drivers/gpu/drm/mcde/mcde_display.c b/drivers/gpu/drm/mcde/mcde_display.c
index 257a6e84dd58..52f071bb347c 100644
--- a/drivers/gpu/drm/mcde/mcde_display.c
+++ b/drivers/gpu/drm/mcde/mcde_display.c
@@ -7,7 +7,7 @@
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/dma-buf.h>
-#include <linux/regulator/consumer.h>
+#include <linux/pm_runtime.h>
 #include <linux/media-bus-format.h>
 
 #include <drm/drm_device.h>
@@ -1168,16 +1168,15 @@ static void mcde_display_enable(struct drm_simple_display_pipe *pipe,
 	int ret;
 
 	/* This powers up the entire MCDE block and the DSI hardware */
-	ret = regulator_enable(mcde->epod);
+	ret = pm_runtime_resume_and_get(mcde->dev);
 	if (ret) {
-		dev_err(drm->dev, "can't re-enable EPOD regulator\n");
+		dev_err(drm->dev, "can't enable MCDE power domain\n");
 		return;
 	}
 
 	dev_info(drm->dev, "enable MCDE, %d x %d format %p4cc\n",
 		 mode->hdisplay, mode->vdisplay, &format);
 
-
 	/* Clear any pending interrupts */
 	mcde_display_disable_irqs(mcde);
 	writel(0, mcde->regs + MCDE_IMSCERR);
@@ -1327,9 +1326,9 @@ static void mcde_display_disable(struct drm_simple_display_pipe *pipe)
 		spin_unlock_irq(&crtc->dev->event_lock);
 	}
 
-	ret = regulator_disable(mcde->epod);
+	ret = pm_runtime_put_sync_suspend(mcde->dev);
 	if (ret)
-		dev_err(drm->dev, "can't disable EPOD regulator\n");
+		dev_err(drm->dev, "can't disable MCDE power domain\n");
 	/* Make sure we are powered down (before we may power up again) */
 	usleep_range(50000, 70000);
 
diff --git a/drivers/gpu/drm/mcde/mcde_drm.h b/drivers/gpu/drm/mcde/mcde_drm.h
index ecb70b4b737c..d4ff7606d917 100644
--- a/drivers/gpu/drm/mcde/mcde_drm.h
+++ b/drivers/gpu/drm/mcde/mcde_drm.h
@@ -91,8 +91,6 @@ struct mcde {
 	/* Locks the MCDE FIFO control register A and B */
 	spinlock_t fifo_crx1_lock;
 
-	struct regulator *epod;
-	struct regulator *vana;
 };
 
 #define to_mcde(dev) container_of(dev, struct mcde, drm)
diff --git a/drivers/gpu/drm/mcde/mcde_drv.c b/drivers/gpu/drm/mcde/mcde_drv.c
index 53275b575f0c..d5a2cc98c65b 100644
--- a/drivers/gpu/drm/mcde/mcde_drv.c
+++ b/drivers/gpu/drm/mcde/mcde_drv.c
@@ -61,7 +61,7 @@
 #include <linux/module.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
-#include <linux/regulator/consumer.h>
+#include <linux/pm_runtime.h>
 #include <linux/slab.h>
 #include <linux/delay.h>
 
@@ -284,45 +284,25 @@ static int mcde_probe(struct platform_device *pdev)
 	mcde->dev = dev;
 	platform_set_drvdata(pdev, drm);
 
-	/* First obtain and turn on the main power */
-	mcde->epod = devm_regulator_get(dev, "epod");
-	if (IS_ERR(mcde->epod)) {
-		ret = PTR_ERR(mcde->epod);
-		dev_err(dev, "can't get EPOD regulator\n");
-		return ret;
-	}
-	ret = regulator_enable(mcde->epod);
+	pm_runtime_enable(dev);
+	ret = pm_runtime_resume_and_get(dev);
 	if (ret) {
-		dev_err(dev, "can't enable EPOD regulator\n");
+		dev_err(dev, "can't enable MCDE power domain\n");
+		pm_runtime_disable(dev);
 		return ret;
 	}
-	mcde->vana = devm_regulator_get(dev, "vana");
-	if (IS_ERR(mcde->vana)) {
-		ret = PTR_ERR(mcde->vana);
-		dev_err(dev, "can't get VANA regulator\n");
-		goto regulator_epod_off;
-	}
-	ret = regulator_enable(mcde->vana);
-	if (ret) {
-		dev_err(dev, "can't enable VANA regulator\n");
-		goto regulator_epod_off;
-	}
-	/*
-	 * The vendor code uses ESRAM (onchip RAM) and need to activate
-	 * the v-esram34 regulator, but we don't use that yet
-	 */
 
 	/* Clock the silicon so we can access the registers */
 	mcde->mcde_clk = devm_clk_get(dev, "mcde");
 	if (IS_ERR(mcde->mcde_clk)) {
 		dev_err(dev, "unable to get MCDE main clock\n");
 		ret = PTR_ERR(mcde->mcde_clk);
-		goto regulator_off;
+		goto pm_runtime_put;
 	}
 	ret = clk_prepare_enable(mcde->mcde_clk);
 	if (ret) {
 		dev_err(dev, "failed to enable MCDE main clock\n");
-		goto regulator_off;
+		goto pm_runtime_put;
 	}
 	dev_info(dev, "MCDE clk rate %lu Hz\n", clk_get_rate(mcde->mcde_clk));
 
@@ -413,14 +393,15 @@ static int mcde_probe(struct platform_device *pdev)
 
 	/*
 	 * Perform an invasive reset of the MCDE and all blocks by
-	 * cutting the power to the subsystem, then bring it back up
+	 * powering down the subsystem, then bring it back up
 	 * later when we enable the display as a result of
 	 * component_master_add_with_match().
 	 */
-	ret = regulator_disable(mcde->epod);
-	if (ret) {
-		dev_err(dev, "can't disable EPOD regulator\n");
-		return ret;
+	ret = pm_runtime_put_sync_suspend(dev);
+	if (ret < 0) {
+		dev_err(dev, "can't disable MCDE power domain\n");
+		pm_runtime_get_noresume(dev);
+		goto clk_disable;
 	}
 	/* Wait 50 ms so we are sure we cut the power */
 	usleep_range(50000, 70000);
@@ -429,25 +410,21 @@ static int mcde_probe(struct platform_device *pdev)
 					      match);
 	if (ret) {
 		dev_err(dev, "failed to add component master\n");
-		/*
-		 * The EPOD regulator is already disabled at this point so some
-		 * special errorpath code is needed
-		 */
-		clk_disable_unprepare(mcde->mcde_clk);
-		regulator_disable(mcde->vana);
-		return ret;
+		goto clk_disable_pm_disabled;
 	}
 
 	return 0;
 
 clk_disable:
 	clk_disable_unprepare(mcde->mcde_clk);
-regulator_off:
-	regulator_disable(mcde->vana);
-regulator_epod_off:
-	regulator_disable(mcde->epod);
+pm_runtime_put:
+	pm_runtime_put_sync_suspend(dev);
+	goto pm_runtime_disable;
+clk_disable_pm_disabled:
+	clk_disable_unprepare(mcde->mcde_clk);
+pm_runtime_disable:
+	pm_runtime_disable(dev);
 	return ret;
-
 }
 
 static void mcde_remove(struct platform_device *pdev)
@@ -457,8 +434,7 @@ static void mcde_remove(struct platform_device *pdev)
 
 	component_master_del(&pdev->dev, &mcde_drm_comp_ops);
 	clk_disable_unprepare(mcde->mcde_clk);
-	regulator_disable(mcde->vana);
-	regulator_disable(mcde->epod);
+	pm_runtime_disable(&pdev->dev);
 }
 
 static void mcde_shutdown(struct platform_device *pdev)
diff --git a/drivers/gpu/drm/mcde/mcde_dsi.c b/drivers/gpu/drm/mcde/mcde_dsi.c
index 694372581840..ab8afb5cb0c5 100644
--- a/drivers/gpu/drm/mcde/mcde_dsi.c
+++ b/drivers/gpu/drm/mcde/mcde_dsi.c
@@ -8,7 +8,6 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
-#include <linux/regulator/consumer.h>
 #include <video/mipi_display.h>
 
 #include <drm/drm_atomic_helper.h>

-- 
2.55.0

[PATCH v2 16/20] misc: sram: Enable runtime PM

[Linus Walleij]

Enable runtime PM for generic SRAM devices after probe has initialized
the SRAM mappings and partitions.

This lets SRAM devices with attached power domains be managed through
runtime PM references from their consumers.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 drivers/misc/sram.c | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/drivers/misc/sram.c b/drivers/misc/sram.c
index c8990e83a65a..7f19dca7b818 100644
--- a/drivers/misc/sram.c
+++ b/drivers/misc/sram.c
@@ -13,6 +13,7 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
 #include <linux/regmap.h>
 #include <linux/slab.h>
 #include <linux/mfd/syscon.h>
@@ -425,6 +426,10 @@ static int sram_probe(struct platform_device *pdev)
 			goto err_free_partitions;
 	}
 
+	ret = devm_pm_runtime_set_active_enabled(&pdev->dev);
+	if (ret)
+		goto err_free_partitions;
+
 	if (sram->pool)
 		dev_dbg(sram->dev, "SRAM pool: %zu KiB @ 0x%p\n",
 			gen_pool_size(sram->pool) / 1024, sram->virt_base);

-- 
2.55.0

[PATCH v2 17/20] dmaengine: ste_dma40: Use power domain for LCLA SRAM

[Linus Walleij]

Replace the LCLA ESRAM regulator with runtime PM.

Use the SRAM device that owns the ESRAM34 power domain.

Hold that domain while DMA transfers are active. The DMA controller is
runtime PM IRQ-safe, so keep taking explicit LCLA runtime PM references
from the descriptor preparation path instead of relying on a runtime PM
device link from the atomic transfer path.

Add a stateless device link so system PM keeps the DMA controller ordered
after the LCLA SRAM supplier.

Suggested-by: Frank Li <Frank.li@oss.nxp.com>
Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 drivers/dma/ste_dma40.c | 130 ++++++++++++++++++++++++++++++++----------------
 1 file changed, 88 insertions(+), 42 deletions(-)

diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
index eda3f91741ed..2841af5b160b 100644
--- a/drivers/dma/ste_dma40.c
+++ b/drivers/dma/ste_dma40.c
@@ -21,8 +21,8 @@
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_dma.h>
+#include <linux/of_platform.h>
 #include <linux/amba/bus.h>
-#include <linux/regulator/consumer.h>
 
 #include "dmaengine.h"
 #include "ste_dma40.h"
@@ -383,6 +383,7 @@ struct d40_lli_pool {
  * @node: List entry.
  * @is_in_client_list: true if the client owns this descriptor.
  * @cyclic: true if this is a cyclic job
+ * @lcla_pm_active: LCLA SRAM power domain is held for this descriptor.
  *
  * This descriptor is used for both logical and physical transfers.
  */
@@ -402,6 +403,7 @@ struct d40_desc {
 
 	bool				 is_in_client_list;
 	bool				 cyclic;
+	bool				 lcla_pm_active;
 };
 
 /**
@@ -571,7 +573,8 @@ struct d40_gen_dmac {
  * to phy_chans entries.
  * @plat_data: Pointer to provided platform_data which is the driver
  * configuration.
- * @lcpa_regulator: Pointer to hold the regulator for the esram bank for lcla.
+ * @lcla_dev: SRAM device for the ESRAM bank used by LCLA.
+ * @lcla_link: Device link to keep system PM ordered against LCLA.
  * @phy_res: Vector containing all physical channels.
  * @lcla_pool: lcla pool settings and data.
  * @lcpa_base: The virtual mapped address of LCPA.
@@ -606,7 +609,8 @@ struct d40_base {
 	struct d40_chan			**lookup_log_chans;
 	struct d40_chan			**lookup_phy_chans;
 	struct stedma40_platform_data	 *plat_data;
-	struct regulator		 *lcpa_regulator;
+	struct device			 *lcla_dev;
+	struct device_link		 *lcla_link;
 	/* Physical half channels */
 	struct d40_phy_res		 *phy_res;
 	struct d40_lcla_pool		  lcla_pool;
@@ -628,6 +632,36 @@ static struct device *chan2dev(struct d40_chan *d40c)
 	return &d40c->chan.dev->device;
 }
 
+static void d40_transfer_runtime_get(struct d40_base *base)
+{
+	pm_runtime_get_sync(base->dev);
+}
+
+static int d40_lcla_runtime_get(struct d40_base *base)
+{
+	if (!base->lcla_dev)
+		return 0;
+
+	return pm_runtime_resume_and_get(base->lcla_dev);
+}
+
+static void d40_desc_lcla_runtime_put(struct d40_chan *d40c,
+				      struct d40_desc *d40d)
+{
+	struct d40_base *base = d40c->base;
+
+	if (!d40d->lcla_pm_active)
+		return;
+
+	d40d->lcla_pm_active = false;
+	pm_runtime_put(base->lcla_dev);
+}
+
+static void d40_transfer_runtime_put(struct d40_base *base)
+{
+	pm_runtime_put_autosuspend(base->dev);
+}
+
 static bool chan_is_physical(struct d40_chan *chan)
 {
 	return chan->log_num == D40_PHY_CHAN;
@@ -818,6 +852,7 @@ static void d40_desc_free(struct d40_chan *d40c, struct d40_desc *d40d)
 
 	d40_pool_lli_free(d40c, d40d);
 	d40_lcla_free_all(d40c, d40d);
+	d40_desc_lcla_runtime_put(d40c, d40d);
 	kmem_cache_free(d40c->base->desc_slab, d40d);
 }
 
@@ -1516,7 +1551,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
 	if (d40d != NULL) {
 		if (!d40c->busy) {
 			d40c->busy = true;
-			pm_runtime_get_sync(d40c->base->dev);
+			d40_transfer_runtime_get(d40c->base);
 		}
 
 		/* Remove from queue */
@@ -1535,6 +1570,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
 			d40_desc_remove(d40d);
 			d40_desc_free(d40c, d40d);
 			d40c->busy = false;
+			d40_transfer_runtime_put(d40c->base);
 			return ERR_PTR(err);
 		}
 	}
@@ -1583,7 +1619,7 @@ static void dma_tc_handle(struct d40_chan *d40c)
 		if (d40_queue_start(d40c) == NULL) {
 			d40c->busy = false;
 
-			pm_runtime_put_autosuspend(d40c->base->dev);
+			d40_transfer_runtime_put(d40c->base);
 		}
 
 		d40_desc_remove(d40d);
@@ -1637,6 +1673,7 @@ static void dma_tasklet(struct tasklet_struct *t)
 		} else if (!d40d->is_in_client_list) {
 			d40_desc_remove(d40d);
 			d40_lcla_free_all(d40c, d40d);
+			d40_desc_lcla_runtime_put(d40c, d40d);
 			list_add_tail(&d40d->node, &d40c->client);
 			d40d->is_in_client_list = true;
 		}
@@ -2067,7 +2104,7 @@ static int d40_free_dma(struct d40_chan *d40c)
 		d40c->base->lookup_phy_chans[phy->num] = NULL;
 
 	if (d40c->busy)
-		pm_runtime_put_autosuspend(d40c->base->dev);
+		d40_transfer_runtime_put(d40c->base);
 
 	d40c->busy = false;
 	d40c->phy_chan = NULL;
@@ -2246,6 +2283,7 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 	dma_addr_t dst_dev_addr;
 	struct d40_desc *desc;
 	unsigned long flags;
+	bool got_lcla_pm = false;
 	int ret;
 
 	if (!chan->phy_chan) {
@@ -2255,11 +2293,20 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 
 	d40_set_runtime_config_write(dchan, &chan->slave_config, direction);
 
+	ret = d40_lcla_runtime_get(chan->base);
+	if (ret) {
+		chan_err(chan, "Failed to enable LCLA power domain\n");
+		return NULL;
+	}
+	got_lcla_pm = !!chan->base->lcla_dev;
+
 	spin_lock_irqsave(&chan->lock, flags);
 
 	desc = d40_prep_desc(chan, sg_src, sg_len, dma_flags);
 	if (desc == NULL)
 		goto unlock;
+	desc->lcla_pm_active = got_lcla_pm;
+	got_lcla_pm = false;
 
 	if (sg_next(&sg_src[sg_len - 1]) == sg_src)
 		desc->cyclic = true;
@@ -2297,6 +2344,8 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
 	d40_desc_free(chan, desc);
  unlock:
 	spin_unlock_irqrestore(&chan->lock, flags);
+	if (got_lcla_pm)
+		pm_runtime_put(chan->base->lcla_dev);
 	return NULL;
 }
 
@@ -2628,7 +2677,7 @@ static int d40_terminate_all(struct dma_chan *chan)
 	d40_term_all(d40c);
 	pm_runtime_put_autosuspend(d40c->base->dev);
 	if (d40c->busy)
-		pm_runtime_put_autosuspend(d40c->base->dev);
+		d40_transfer_runtime_put(d40c->base);
 	d40c->busy = false;
 
 	spin_unlock_irqrestore(&d40c->lock, flags);
@@ -2931,29 +2980,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,
 #ifdef CONFIG_PM_SLEEP
 static int dma40_suspend(struct device *dev)
 {
-	struct d40_base *base = dev_get_drvdata(dev);
-	int ret;
-
-	ret = pm_runtime_force_suspend(dev);
-	if (ret)
-		return ret;
-
-	if (base->lcpa_regulator)
-		ret = regulator_disable(base->lcpa_regulator);
-	return ret;
+	return pm_runtime_force_suspend(dev);
 }
 
 static int dma40_resume(struct device *dev)
 {
-	struct d40_base *base = dev_get_drvdata(dev);
-	int ret = 0;
-
-	if (base->lcpa_regulator) {
-		ret = regulator_enable(base->lcpa_regulator);
-		if (ret)
-			return ret;
-	}
-
 	return pm_runtime_force_resume(dev);
 }
 #endif
@@ -3509,7 +3540,10 @@ static int __init d40_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct device_node *np = pdev->dev.of_node;
 	struct device_node *np_lcpa;
+	struct device_node *np_lcla;
+	struct device_node *np_lcla_parent;
 	struct d40_base *base;
+	struct platform_device *lcla_pdev;
 	struct resource *res;
 	struct resource res_lcpa;
 	int num_reserved_chans;
@@ -3610,21 +3644,32 @@ static int __init d40_probe(struct platform_device *pdev)
 	irq_requested = true;
 
 	if (base->plat_data->use_esram_lcla) {
+		np_lcla = of_parse_phandle(np, "sram", 1);
+		if (!np_lcla) {
+			dev_err(dev, "no LCLA SRAM node\n");
+			ret = -EINVAL;
+			goto destroy_cache;
+		}
 
-		base->lcpa_regulator = regulator_get(base->dev, "lcla_esram");
-		if (IS_ERR(base->lcpa_regulator)) {
-			d40_err(dev, "Failed to get lcpa_regulator\n");
-			ret = PTR_ERR(base->lcpa_regulator);
-			base->lcpa_regulator = NULL;
+		np_lcla_parent = of_get_parent(np_lcla);
+		of_node_put(np_lcla);
+		if (!np_lcla_parent) {
+			dev_err(dev, "no LCLA SRAM parent node\n");
+			ret = -EINVAL;
 			goto destroy_cache;
 		}
 
-		ret = regulator_enable(base->lcpa_regulator);
-		if (ret) {
-			d40_err(dev,
-				"Failed to enable lcpa_regulator\n");
-			regulator_put(base->lcpa_regulator);
-			base->lcpa_regulator = NULL;
+		lcla_pdev = of_find_device_by_node(np_lcla_parent);
+		of_node_put(np_lcla_parent);
+		if (!lcla_pdev) {
+			ret = -EPROBE_DEFER;
+			goto destroy_cache;
+		}
+		base->lcla_dev = &lcla_pdev->dev;
+		base->lcla_link = device_link_add(dev, base->lcla_dev,
+						  DL_FLAG_STATELESS);
+		if (!base->lcla_link) {
+			ret = -ENODEV;
 			goto destroy_cache;
 		}
 	}
@@ -3663,16 +3708,17 @@ static int __init d40_probe(struct platform_device *pdev)
 				 SZ_1K * base->num_phy_chans,
 				 DMA_TO_DEVICE);
 
-	if (!base->lcla_pool.base_unaligned && base->lcla_pool.base)
+	if (!base->lcla_pool.base_unaligned && base->lcla_pool.base &&
+	    base->lcla_pool.pages)
 		free_pages((unsigned long)base->lcla_pool.base,
 			   base->lcla_pool.pages);
 
 	kfree(base->lcla_pool.base_unaligned);
 
-	if (base->lcpa_regulator) {
-		regulator_disable(base->lcpa_regulator);
-		regulator_put(base->lcpa_regulator);
-	}
+	if (base->lcla_link)
+		device_link_del(base->lcla_link);
+	if (base->lcla_dev)
+		put_device(base->lcla_dev);
 	if (irq_requested)
 		free_irq(base->irq, base);
 	if (runtime_pm_enabled)

-- 
2.55.0

[PATCH v2 18/20] mfd/regulator: db8500-prcmu: Remove EPOD regulators

[Linus Walleij]

Remove the obsolete DB8500 PRCMU regulator drivers.

Drop the regulator build hooks and the db8500-prcmu-regulators MFD
cell now that EPODs are power domains.

Assisted-by: LLM
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 drivers/mfd/db8500-prcmu.c             | 239 ----------------
 drivers/regulator/Kconfig              |  12 -
 drivers/regulator/Makefile             |   2 -
 drivers/regulator/db8500-prcmu.c       | 501 ---------------------------------
 drivers/regulator/dbx500-prcmu.c       | 155 ----------
 drivers/regulator/dbx500-prcmu.h       |  55 ----
 include/linux/regulator/db8500-prcmu.h |  38 ---
 7 files changed, 1002 deletions(-)

diff --git a/drivers/mfd/db8500-prcmu.c b/drivers/mfd/db8500-prcmu.c
index 6672c55f2ebc..687bbf79559e 100644
--- a/drivers/mfd/db8500-prcmu.c
+++ b/drivers/mfd/db8500-prcmu.c
@@ -34,8 +34,6 @@
 #include <linux/mfd/core.h>
 #include <linux/mfd/db8500-prcmu.h>
 #include <linux/mfd/abx500/ab8500.h>
-#include <linux/regulator/db8500-prcmu.h>
-#include <linux/regulator/machine.h>
 #include "db8500-prcmu-regs.h"
 
 /* Index of different voltages to be used when accessing AVSData */
@@ -2704,249 +2702,12 @@ static void init_prcm_registers(void)
 	writel(val, (PRCM_A9PL_FORCE_CLKEN));
 }
 
-/*
- * Power domain switches (ePODs) modeled as regulators for the DB8500 SoC
- */
-static struct regulator_consumer_supply db8500_vape_consumers[] = {
-	REGULATOR_SUPPLY("v-ape", NULL),
-	REGULATOR_SUPPLY("v-i2c", "nmk-i2c.0"),
-	REGULATOR_SUPPLY("v-i2c", "nmk-i2c.1"),
-	REGULATOR_SUPPLY("v-i2c", "nmk-i2c.2"),
-	REGULATOR_SUPPLY("v-i2c", "nmk-i2c.3"),
-	REGULATOR_SUPPLY("v-i2c", "nmk-i2c.4"),
-	/* "v-mmc" changed to "vcore" in the mainline kernel */
-	REGULATOR_SUPPLY("vcore", "sdi0"),
-	REGULATOR_SUPPLY("vcore", "sdi1"),
-	REGULATOR_SUPPLY("vcore", "sdi2"),
-	REGULATOR_SUPPLY("vcore", "sdi3"),
-	REGULATOR_SUPPLY("vcore", "sdi4"),
-	REGULATOR_SUPPLY("v-dma", "dma40.0"),
-	REGULATOR_SUPPLY("v-ape", "ab8500-usb.0"),
-	/* "v-uart" changed to "vcore" in the mainline kernel */
-	REGULATOR_SUPPLY("vcore", "uart0"),
-	REGULATOR_SUPPLY("vcore", "uart1"),
-	REGULATOR_SUPPLY("vcore", "uart2"),
-	REGULATOR_SUPPLY("v-ape", "nmk-ske-keypad.0"),
-	REGULATOR_SUPPLY("v-hsi", "ste_hsi.0"),
-	REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
-};
-
-static struct regulator_consumer_supply db8500_vsmps2_consumers[] = {
-	REGULATOR_SUPPLY("musb_1v8", "ab8500-usb.0"),
-	/* AV8100 regulator */
-	REGULATOR_SUPPLY("hdmi_1v8", "0-0070"),
-};
-
-static struct regulator_consumer_supply db8500_b2r2_mcde_consumers[] = {
-	REGULATOR_SUPPLY("vsupply", "b2r2_bus"),
-	REGULATOR_SUPPLY("vsupply", "mcde"),
-};
-
-/* SVA MMDSP regulator switch */
-static struct regulator_consumer_supply db8500_svammdsp_consumers[] = {
-	REGULATOR_SUPPLY("sva-mmdsp", "cm_control"),
-};
-
-/* SVA pipe regulator switch */
-static struct regulator_consumer_supply db8500_svapipe_consumers[] = {
-	REGULATOR_SUPPLY("sva-pipe", "cm_control"),
-};
-
-/* SIA MMDSP regulator switch */
-static struct regulator_consumer_supply db8500_siammdsp_consumers[] = {
-	REGULATOR_SUPPLY("sia-mmdsp", "cm_control"),
-};
-
-/* SIA pipe regulator switch */
-static struct regulator_consumer_supply db8500_siapipe_consumers[] = {
-	REGULATOR_SUPPLY("sia-pipe", "cm_control"),
-};
-
-static struct regulator_consumer_supply db8500_sga_consumers[] = {
-	REGULATOR_SUPPLY("v-mali", NULL),
-};
-
-/* ESRAM1 and 2 regulator switch */
-static struct regulator_consumer_supply db8500_esram12_consumers[] = {
-	REGULATOR_SUPPLY("esram12", "cm_control"),
-};
-
-/* ESRAM3 and 4 regulator switch */
-static struct regulator_consumer_supply db8500_esram34_consumers[] = {
-	REGULATOR_SUPPLY("v-esram34", "mcde"),
-	REGULATOR_SUPPLY("esram34", "cm_control"),
-	REGULATOR_SUPPLY("lcla_esram", "dma40.0"),
-};
-
-static struct regulator_init_data db8500_regulators[DB8500_NUM_REGULATORS] = {
-	[DB8500_REGULATOR_VAPE] = {
-		.constraints = {
-			.name = "db8500-vape",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-			.always_on = true,
-		},
-		.consumer_supplies = db8500_vape_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_vape_consumers),
-	},
-	[DB8500_REGULATOR_VARM] = {
-		.constraints = {
-			.name = "db8500-varm",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_VMODEM] = {
-		.constraints = {
-			.name = "db8500-vmodem",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_VPLL] = {
-		.constraints = {
-			.name = "db8500-vpll",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_VSMPS1] = {
-		.constraints = {
-			.name = "db8500-vsmps1",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_VSMPS2] = {
-		.constraints = {
-			.name = "db8500-vsmps2",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_vsmps2_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_vsmps2_consumers),
-	},
-	[DB8500_REGULATOR_VSMPS3] = {
-		.constraints = {
-			.name = "db8500-vsmps3",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_VRF1] = {
-		.constraints = {
-			.name = "db8500-vrf1",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_SWITCH_SVAMMDSP] = {
-		/* dependency to u8500-vape is handled outside regulator framework */
-		.constraints = {
-			.name = "db8500-sva-mmdsp",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_svammdsp_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_svammdsp_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_SVAMMDSPRET] = {
-		.constraints = {
-			/* "ret" means "retention" */
-			.name = "db8500-sva-mmdsp-ret",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_SWITCH_SVAPIPE] = {
-		/* dependency to u8500-vape is handled outside regulator framework */
-		.constraints = {
-			.name = "db8500-sva-pipe",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_svapipe_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_svapipe_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_SIAMMDSP] = {
-		/* dependency to u8500-vape is handled outside regulator framework */
-		.constraints = {
-			.name = "db8500-sia-mmdsp",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_siammdsp_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_siammdsp_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_SIAMMDSPRET] = {
-		.constraints = {
-			.name = "db8500-sia-mmdsp-ret",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_SWITCH_SIAPIPE] = {
-		/* dependency to u8500-vape is handled outside regulator framework */
-		.constraints = {
-			.name = "db8500-sia-pipe",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_siapipe_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_siapipe_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_SGA] = {
-		.supply_regulator = "db8500-vape",
-		.constraints = {
-			.name = "db8500-sga",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_sga_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_sga_consumers),
-
-	},
-	[DB8500_REGULATOR_SWITCH_B2R2_MCDE] = {
-		.supply_regulator = "db8500-vape",
-		.constraints = {
-			.name = "db8500-b2r2-mcde",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_b2r2_mcde_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_b2r2_mcde_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM12] = {
-		/*
-		 * esram12 is set in retention and supplied by Vsafe when Vape is off,
-		 * no need to hold Vape
-		 */
-		.constraints = {
-			.name = "db8500-esram12",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_esram12_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_esram12_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM12RET] = {
-		.constraints = {
-			.name = "db8500-esram12-ret",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM34] = {
-		/*
-		 * esram34 is set in retention and supplied by Vsafe when Vape is off,
-		 * no need to hold Vape
-		 */
-		.constraints = {
-			.name = "db8500-esram34",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-		.consumer_supplies = db8500_esram34_consumers,
-		.num_consumer_supplies = ARRAY_SIZE(db8500_esram34_consumers),
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM34RET] = {
-		.constraints = {
-			.name = "db8500-esram34-ret",
-			.valid_ops_mask = REGULATOR_CHANGE_STATUS,
-		},
-	},
-};
-
 static const struct mfd_cell common_prcmu_devs[] = {
 	MFD_CELL_NAME("db8500_wdt"),
 	MFD_CELL_NAME("db8500-cpuidle"),
 };
 
 static const struct mfd_cell db8500_prcmu_devs[] = {
-	MFD_CELL_OF("db8500-prcmu-regulators", NULL,
-		    &db8500_regulators, sizeof(db8500_regulators), 0,
-		    "stericsson,db8500-prcmu-regulator"),
 	MFD_CELL_OF("db8500-thermal",
 		    NULL, NULL, 0, 0, "stericsson,db8500-thermal"),
 };
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index 851e1a8fc22f..c2d6a895245e 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -408,18 +408,6 @@ config REGULATOR_DA9211
 	  step down converter 12A or 16A DC-DC Buck controlled through an I2C
 	  interface.
 
-config REGULATOR_DBX500_PRCMU
-	bool
-
-config REGULATOR_DB8500_PRCMU
-	bool "ST-Ericsson DB8500 Voltage Domain Regulators"
-	depends on MFD_DB8500_PRCMU
-	depends on !UX500_PM_DOMAIN
-	select REGULATOR_DBX500_PRCMU
-	help
-	  This driver supports the voltage domain regulators controlled by the
-	  DB8500 PRCMU
-
 config REGULATOR_FAN53555
 	tristate "Fairchild FAN53555 Regulator"
 	depends on I2C
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 5a764cec8df8..efe78600fda9 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -48,8 +48,6 @@ obj-$(CONFIG_REGULATOR_DA9063)	+= da9063-regulator.o
 obj-$(CONFIG_REGULATOR_DA9121) += da9121-regulator.o
 obj-$(CONFIG_REGULATOR_DA9210) += da9210-regulator.o
 obj-$(CONFIG_REGULATOR_DA9211) += da9211-regulator.o
-obj-$(CONFIG_REGULATOR_DBX500_PRCMU) += dbx500-prcmu.o
-obj-$(CONFIG_REGULATOR_DB8500_PRCMU) += db8500-prcmu.o
 obj-$(CONFIG_REGULATOR_FAN53555) += fan53555.o
 obj-$(CONFIG_REGULATOR_FAN53880) += fan53880.o
 obj-$(CONFIG_REGULATOR_GPIO) += gpio-regulator.o
diff --git a/drivers/regulator/db8500-prcmu.c b/drivers/regulator/db8500-prcmu.c
deleted file mode 100644
index 751fe36580fa..000000000000
--- a/drivers/regulator/db8500-prcmu.c
+++ /dev/null
@@ -1,501 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Authors: Sundar Iyer <sundar.iyer@stericsson.com> for ST-Ericsson
- *          Bengt Jonsson <bengt.g.jonsson@stericsson.com> for ST-Ericsson
- *
- * Power domain regulators on DB8500
- */
-
-#include <linux/kernel.h>
-#include <linux/init.h>
-#include <linux/err.h>
-#include <linux/spinlock.h>
-#include <linux/platform_device.h>
-#include <linux/mfd/db8500-prcmu.h>
-#include <linux/regulator/driver.h>
-#include <linux/regulator/machine.h>
-#include <linux/regulator/db8500-prcmu.h>
-#include <linux/regulator/of_regulator.h>
-#include <linux/of.h>
-#include <linux/module.h>
-#include "dbx500-prcmu.h"
-
-static int db8500_regulator_enable(struct regulator_dev *rdev)
-{
-	struct dbx500_regulator_info *info = rdev_get_drvdata(rdev);
-
-	if (info == NULL)
-		return -EINVAL;
-
-	dev_vdbg(rdev_get_dev(rdev), "regulator-%s-enable\n",
-		info->desc.name);
-
-	if (!info->is_enabled) {
-		info->is_enabled = true;
-		if (!info->exclude_from_power_state)
-			power_state_active_enable();
-	}
-
-	return 0;
-}
-
-static int db8500_regulator_disable(struct regulator_dev *rdev)
-{
-	struct dbx500_regulator_info *info = rdev_get_drvdata(rdev);
-	int ret = 0;
-
-	if (info == NULL)
-		return -EINVAL;
-
-	dev_vdbg(rdev_get_dev(rdev), "regulator-%s-disable\n",
-		info->desc.name);
-
-	if (info->is_enabled) {
-		info->is_enabled = false;
-		if (!info->exclude_from_power_state)
-			ret = power_state_active_disable();
-	}
-
-	return ret;
-}
-
-static int db8500_regulator_is_enabled(struct regulator_dev *rdev)
-{
-	struct dbx500_regulator_info *info = rdev_get_drvdata(rdev);
-
-	if (info == NULL)
-		return -EINVAL;
-
-	dev_vdbg(rdev_get_dev(rdev), "regulator-%s-is_enabled (is_enabled):"
-		" %i\n", info->desc.name, info->is_enabled);
-
-	return info->is_enabled;
-}
-
-/* db8500 regulator operations */
-static const struct regulator_ops db8500_regulator_ops = {
-	.enable			= db8500_regulator_enable,
-	.disable		= db8500_regulator_disable,
-	.is_enabled		= db8500_regulator_is_enabled,
-};
-
-/*
- * EPOD control
- */
-static bool epod_on[NUM_EPOD_ID];
-static bool epod_ramret[NUM_EPOD_ID];
-
-static int enable_epod(u16 epod_id, bool ramret)
-{
-	int ret;
-
-	if (ramret) {
-		if (!epod_on[epod_id]) {
-			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_RAMRET);
-			if (ret < 0)
-				return ret;
-		}
-		epod_ramret[epod_id] = true;
-	} else {
-		ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_ON);
-		if (ret < 0)
-			return ret;
-		epod_on[epod_id] = true;
-	}
-
-	return 0;
-}
-
-static int disable_epod(u16 epod_id, bool ramret)
-{
-	int ret;
-
-	if (ramret) {
-		if (!epod_on[epod_id]) {
-			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_OFF);
-			if (ret < 0)
-				return ret;
-		}
-		epod_ramret[epod_id] = false;
-	} else {
-		if (epod_ramret[epod_id]) {
-			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_RAMRET);
-			if (ret < 0)
-				return ret;
-		} else {
-			ret = db8500_prcmu_set_epod(epod_id, EPOD_STATE_OFF);
-			if (ret < 0)
-				return ret;
-		}
-		epod_on[epod_id] = false;
-	}
-
-	return 0;
-}
-
-/*
- * Regulator switch
- */
-static int db8500_regulator_switch_enable(struct regulator_dev *rdev)
-{
-	struct dbx500_regulator_info *info = rdev_get_drvdata(rdev);
-	int ret;
-
-	if (info == NULL)
-		return -EINVAL;
-
-	dev_vdbg(rdev_get_dev(rdev), "regulator-switch-%s-enable\n",
-		info->desc.name);
-
-	ret = enable_epod(info->epod_id, info->is_ramret);
-	if (ret < 0) {
-		dev_err(rdev_get_dev(rdev),
-			"regulator-switch-%s-enable: prcmu call failed\n",
-			info->desc.name);
-		goto out;
-	}
-
-	info->is_enabled = true;
-out:
-	return ret;
-}
-
-static int db8500_regulator_switch_disable(struct regulator_dev *rdev)
-{
-	struct dbx500_regulator_info *info = rdev_get_drvdata(rdev);
-	int ret;
-
-	if (info == NULL)
-		return -EINVAL;
-
-	dev_vdbg(rdev_get_dev(rdev), "regulator-switch-%s-disable\n",
-		info->desc.name);
-
-	ret = disable_epod(info->epod_id, info->is_ramret);
-	if (ret < 0) {
-		dev_err(rdev_get_dev(rdev),
-			"regulator_switch-%s-disable: prcmu call failed\n",
-			info->desc.name);
-		goto out;
-	}
-
-	info->is_enabled = false;
-out:
-	return ret;
-}
-
-static int db8500_regulator_switch_is_enabled(struct regulator_dev *rdev)
-{
-	struct dbx500_regulator_info *info = rdev_get_drvdata(rdev);
-
-	if (info == NULL)
-		return -EINVAL;
-
-	dev_vdbg(rdev_get_dev(rdev),
-		"regulator-switch-%s-is_enabled (is_enabled): %i\n",
-		info->desc.name, info->is_enabled);
-
-	return info->is_enabled;
-}
-
-static const struct regulator_ops db8500_regulator_switch_ops = {
-	.enable			= db8500_regulator_switch_enable,
-	.disable		= db8500_regulator_switch_disable,
-	.is_enabled		= db8500_regulator_switch_is_enabled,
-};
-
-/*
- * Regulator information
- */
-static struct dbx500_regulator_info
-dbx500_regulator_info[DB8500_NUM_REGULATORS] = {
-	[DB8500_REGULATOR_VAPE] = {
-		.desc = {
-			.name	= "db8500-vape",
-			.of_match = of_match_ptr("db8500_vape"),
-			.id	= DB8500_REGULATOR_VAPE,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_VARM] = {
-		.desc = {
-			.name	= "db8500-varm",
-			.of_match = of_match_ptr("db8500_varm"),
-			.id	= DB8500_REGULATOR_VARM,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_VMODEM] = {
-		.desc = {
-			.name	= "db8500-vmodem",
-			.of_match = of_match_ptr("db8500_vmodem"),
-			.id	= DB8500_REGULATOR_VMODEM,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_VPLL] = {
-		.desc = {
-			.name	= "db8500-vpll",
-			.of_match = of_match_ptr("db8500_vpll"),
-			.id	= DB8500_REGULATOR_VPLL,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_VSMPS1] = {
-		.desc = {
-			.name	= "db8500-vsmps1",
-			.of_match = of_match_ptr("db8500_vsmps1"),
-			.id	= DB8500_REGULATOR_VSMPS1,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_VSMPS2] = {
-		.desc = {
-			.name	= "db8500-vsmps2",
-			.of_match = of_match_ptr("db8500_vsmps2"),
-			.id	= DB8500_REGULATOR_VSMPS2,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-			.fixed_uV = 1800000,
-			.n_voltages = 1,
-		},
-		.exclude_from_power_state = true,
-	},
-	[DB8500_REGULATOR_VSMPS3] = {
-		.desc = {
-			.name	= "db8500-vsmps3",
-			.of_match = of_match_ptr("db8500_vsmps3"),
-			.id	= DB8500_REGULATOR_VSMPS3,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_VRF1] = {
-		.desc = {
-			.name	= "db8500-vrf1",
-			.of_match = of_match_ptr("db8500_vrf1"),
-			.id	= DB8500_REGULATOR_VRF1,
-			.ops	= &db8500_regulator_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-	},
-	[DB8500_REGULATOR_SWITCH_SVAMMDSP] = {
-		.desc = {
-			.name	= "db8500-sva-mmdsp",
-			.of_match = of_match_ptr("db8500_sva_mmdsp"),
-			.id	= DB8500_REGULATOR_SWITCH_SVAMMDSP,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SVAMMDSP,
-	},
-	[DB8500_REGULATOR_SWITCH_SVAMMDSPRET] = {
-		.desc = {
-			.name	= "db8500-sva-mmdsp-ret",
-			.of_match = of_match_ptr("db8500_sva_mmdsp_ret"),
-			.id	= DB8500_REGULATOR_SWITCH_SVAMMDSPRET,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SVAMMDSP,
-		.is_ramret = true,
-	},
-	[DB8500_REGULATOR_SWITCH_SVAPIPE] = {
-		.desc = {
-			.name	= "db8500-sva-pipe",
-			.of_match = of_match_ptr("db8500_sva_pipe"),
-			.id	= DB8500_REGULATOR_SWITCH_SVAPIPE,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SVAPIPE,
-	},
-	[DB8500_REGULATOR_SWITCH_SIAMMDSP] = {
-		.desc = {
-			.name	= "db8500-sia-mmdsp",
-			.of_match = of_match_ptr("db8500_sia_mmdsp"),
-			.id	= DB8500_REGULATOR_SWITCH_SIAMMDSP,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SIAMMDSP,
-	},
-	[DB8500_REGULATOR_SWITCH_SIAMMDSPRET] = {
-		.desc = {
-			.name	= "db8500-sia-mmdsp-ret",
-			.of_match = of_match_ptr("db8500_sia_mmdsp_ret"),
-			.id	= DB8500_REGULATOR_SWITCH_SIAMMDSPRET,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SIAMMDSP,
-		.is_ramret = true,
-	},
-	[DB8500_REGULATOR_SWITCH_SIAPIPE] = {
-		.desc = {
-			.name	= "db8500-sia-pipe",
-			.of_match = of_match_ptr("db8500_sia_pipe"),
-			.id	= DB8500_REGULATOR_SWITCH_SIAPIPE,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SIAPIPE,
-	},
-	[DB8500_REGULATOR_SWITCH_SGA] = {
-		.desc = {
-			.name	= "db8500-sga",
-			.of_match = of_match_ptr("db8500_sga"),
-			.id	= DB8500_REGULATOR_SWITCH_SGA,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_SGA,
-	},
-	[DB8500_REGULATOR_SWITCH_B2R2_MCDE] = {
-		.desc = {
-			.name	= "db8500-b2r2-mcde",
-			.of_match = of_match_ptr("db8500_b2r2_mcde"),
-			.id	= DB8500_REGULATOR_SWITCH_B2R2_MCDE,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_B2R2_MCDE,
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM12] = {
-		.desc = {
-			.name	= "db8500-esram12",
-			.of_match = of_match_ptr("db8500_esram12"),
-			.id	= DB8500_REGULATOR_SWITCH_ESRAM12,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id	= EPOD_ID_ESRAM12,
-		.is_enabled	= true,
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM12RET] = {
-		.desc = {
-			.name	= "db8500-esram12-ret",
-			.of_match = of_match_ptr("db8500_esram12_ret"),
-			.id	= DB8500_REGULATOR_SWITCH_ESRAM12RET,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_ESRAM12,
-		.is_ramret = true,
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM34] = {
-		.desc = {
-			.name	= "db8500-esram34",
-			.of_match = of_match_ptr("db8500_esram34"),
-			.id	= DB8500_REGULATOR_SWITCH_ESRAM34,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id	= EPOD_ID_ESRAM34,
-		.is_enabled	= true,
-	},
-	[DB8500_REGULATOR_SWITCH_ESRAM34RET] = {
-		.desc = {
-			.name	= "db8500-esram34-ret",
-			.of_match = of_match_ptr("db8500_esram34_ret"),
-			.id	= DB8500_REGULATOR_SWITCH_ESRAM34RET,
-			.ops	= &db8500_regulator_switch_ops,
-			.type	= REGULATOR_VOLTAGE,
-			.owner	= THIS_MODULE,
-		},
-		.epod_id = EPOD_ID_ESRAM34,
-		.is_ramret = true,
-	},
-};
-
-static int db8500_regulator_probe(struct platform_device *pdev)
-{
-	struct regulator_init_data *db8500_init_data;
-	struct dbx500_regulator_info *info;
-	struct regulator_config config = { };
-	struct regulator_dev *rdev;
-	int err, i;
-
-	db8500_init_data = dev_get_platdata(&pdev->dev);
-
-	for (i = 0; i < ARRAY_SIZE(dbx500_regulator_info); i++) {
-		/* assign per-regulator data */
-		info = &dbx500_regulator_info[i];
-
-		config.driver_data = info;
-		config.dev = &pdev->dev;
-		if (db8500_init_data)
-			config.init_data = &db8500_init_data[i];
-
-		rdev = devm_regulator_register(&pdev->dev, &info->desc,
-					       &config);
-		if (IS_ERR(rdev)) {
-			err = PTR_ERR(rdev);
-			dev_err(&pdev->dev, "failed to register %s: err %i\n",
-				info->desc.name, err);
-			return err;
-		}
-		dev_dbg(&pdev->dev, "regulator-%s-probed\n", info->desc.name);
-	}
-
-	ux500_regulator_debug_init(pdev, dbx500_regulator_info,
-				   ARRAY_SIZE(dbx500_regulator_info));
-	return 0;
-}
-
-static void db8500_regulator_remove(struct platform_device *pdev)
-{
-	ux500_regulator_debug_exit();
-}
-
-static struct platform_driver db8500_regulator_driver = {
-	.driver = {
-		.name = "db8500-prcmu-regulators",
-		.probe_type = PROBE_PREFER_ASYNCHRONOUS,
-	},
-	.probe = db8500_regulator_probe,
-	.remove = db8500_regulator_remove,
-};
-
-static int __init db8500_regulator_init(void)
-{
-	return platform_driver_register(&db8500_regulator_driver);
-}
-
-static void __exit db8500_regulator_exit(void)
-{
-	platform_driver_unregister(&db8500_regulator_driver);
-}
-
-arch_initcall(db8500_regulator_init);
-module_exit(db8500_regulator_exit);
-
-MODULE_AUTHOR("STMicroelectronics/ST-Ericsson");
-MODULE_DESCRIPTION("DB8500 regulator driver");
-MODULE_LICENSE("GPL v2");
diff --git a/drivers/regulator/dbx500-prcmu.c b/drivers/regulator/dbx500-prcmu.c
deleted file mode 100644
index a45c1e1ac7ef..000000000000
--- a/drivers/regulator/dbx500-prcmu.c
+++ /dev/null
@@ -1,155 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Authors: Sundar Iyer <sundar.iyer@stericsson.com> for ST-Ericsson
- *          Bengt Jonsson <bengt.g.jonsson@stericsson.com> for ST-Ericsson
- *
- * UX500 common part of Power domain regulators
- */
-
-#include <linux/kernel.h>
-#include <linux/err.h>
-#include <linux/regulator/driver.h>
-#include <linux/debugfs.h>
-#include <linux/seq_file.h>
-#include <linux/slab.h>
-#include <linux/module.h>
-
-#include "dbx500-prcmu.h"
-
-/*
- * power state reference count
- */
-static int power_state_active_cnt; /* will initialize to zero */
-static DEFINE_SPINLOCK(power_state_active_lock);
-
-void power_state_active_enable(void)
-{
-	unsigned long flags;
-
-	spin_lock_irqsave(&power_state_active_lock, flags);
-	power_state_active_cnt++;
-	spin_unlock_irqrestore(&power_state_active_lock, flags);
-}
-
-int power_state_active_disable(void)
-{
-	int ret = 0;
-	unsigned long flags;
-
-	spin_lock_irqsave(&power_state_active_lock, flags);
-	if (power_state_active_cnt <= 0) {
-		pr_err("power state: unbalanced enable/disable calls\n");
-		ret = -EINVAL;
-		goto out;
-	}
-
-	power_state_active_cnt--;
-out:
-	spin_unlock_irqrestore(&power_state_active_lock, flags);
-	return ret;
-}
-
-#ifdef CONFIG_REGULATOR_DEBUG
-
-static int power_state_active_get(void)
-{
-	unsigned long flags;
-	int cnt;
-
-	spin_lock_irqsave(&power_state_active_lock, flags);
-	cnt = power_state_active_cnt;
-	spin_unlock_irqrestore(&power_state_active_lock, flags);
-
-	return cnt;
-}
-
-static struct ux500_regulator_debug {
-	struct dentry *dir;
-	struct dbx500_regulator_info *regulator_array;
-	int num_regulators;
-	u8 *state_before_suspend;
-	u8 *state_after_suspend;
-} rdebug;
-
-static int ux500_regulator_power_state_cnt_show(struct seq_file *s, void *p)
-{
-	/* print power state count */
-	seq_printf(s, "ux500-regulator power state count: %i\n",
-		   power_state_active_get());
-
-	return 0;
-}
-DEFINE_SHOW_ATTRIBUTE(ux500_regulator_power_state_cnt);
-
-static int ux500_regulator_status_show(struct seq_file *s, void *p)
-{
-	int i;
-
-	/* print dump header */
-	seq_puts(s, "ux500-regulator status:\n");
-	seq_printf(s, "%31s : %8s : %8s\n", "current", "before", "after");
-
-	for (i = 0; i < rdebug.num_regulators; i++) {
-		struct dbx500_regulator_info *info;
-		/* Access per-regulator data */
-		info = &rdebug.regulator_array[i];
-
-		/* print status */
-		seq_printf(s, "%20s : %8s : %8s : %8s\n",
-			   info->desc.name,
-			   info->is_enabled ? "enabled" : "disabled",
-			   rdebug.state_before_suspend[i] ? "enabled" : "disabled",
-			   rdebug.state_after_suspend[i] ? "enabled" : "disabled");
-	}
-
-	return 0;
-}
-DEFINE_SHOW_ATTRIBUTE(ux500_regulator_status);
-
-int
-ux500_regulator_debug_init(struct platform_device *pdev,
-	struct dbx500_regulator_info *regulator_info,
-	int num_regulators)
-{
-	/* create directory */
-	rdebug.dir = debugfs_create_dir("ux500-regulator", NULL);
-
-	/* create "status" file */
-	debugfs_create_file("status", 0444, rdebug.dir, &pdev->dev,
-			    &ux500_regulator_status_fops);
-
-	/* create "power-state-count" file */
-	debugfs_create_file("power-state-count", 0444, rdebug.dir,
-			    &pdev->dev, &ux500_regulator_power_state_cnt_fops);
-
-	rdebug.regulator_array = regulator_info;
-	rdebug.num_regulators = num_regulators;
-
-	rdebug.state_before_suspend = kzalloc(num_regulators, GFP_KERNEL);
-	if (!rdebug.state_before_suspend)
-		goto exit_destroy_power_state;
-
-	rdebug.state_after_suspend = kzalloc(num_regulators, GFP_KERNEL);
-	if (!rdebug.state_after_suspend)
-		goto exit_free;
-
-	return 0;
-
-exit_free:
-	kfree(rdebug.state_before_suspend);
-exit_destroy_power_state:
-	debugfs_remove_recursive(rdebug.dir);
-	return -ENOMEM;
-}
-
-int ux500_regulator_debug_exit(void)
-{
-	debugfs_remove_recursive(rdebug.dir);
-	kfree(rdebug.state_after_suspend);
-	kfree(rdebug.state_before_suspend);
-
-	return 0;
-}
-#endif
diff --git a/drivers/regulator/dbx500-prcmu.h b/drivers/regulator/dbx500-prcmu.h
deleted file mode 100644
index 2fb3aaef9dbb..000000000000
--- a/drivers/regulator/dbx500-prcmu.h
+++ /dev/null
@@ -1,55 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Bengt Jonsson <bengt.jonsson@stericsson.com> for ST-Ericsson,
- *	   Jonas Aaberg <jonas.aberg@stericsson.com> for ST-Ericsson
- */
-
-#ifndef DBX500_REGULATOR_H
-#define DBX500_REGULATOR_H
-
-#include <linux/platform_device.h>
-
-/**
- * struct dbx500_regulator_info - dbx500 regulator information
- * @desc: regulator description
- * @is_enabled: status of the regulator
- * @epod_id: id for EPOD (power domain)
- * @is_ramret: RAM retention switch for EPOD (power domain)
- *
- */
-struct dbx500_regulator_info {
-	struct regulator_desc desc;
-	bool is_enabled;
-	u16 epod_id;
-	bool is_ramret;
-	bool exclude_from_power_state;
-};
-
-void power_state_active_enable(void);
-int power_state_active_disable(void);
-
-
-#ifdef CONFIG_REGULATOR_DEBUG
-int ux500_regulator_debug_init(struct platform_device *pdev,
-			       struct dbx500_regulator_info *regulator_info,
-			       int num_regulators);
-
-int ux500_regulator_debug_exit(void);
-#else
-
-static inline int ux500_regulator_debug_init(struct platform_device *pdev,
-			     struct dbx500_regulator_info *regulator_info,
-			     int num_regulators)
-{
-	return 0;
-}
-
-static inline int ux500_regulator_debug_exit(void)
-{
-	return 0;
-}
-
-#endif
-#endif
diff --git a/include/linux/regulator/db8500-prcmu.h b/include/linux/regulator/db8500-prcmu.h
deleted file mode 100644
index d58ff273157e..000000000000
--- a/include/linux/regulator/db8500-prcmu.h
+++ /dev/null
@@ -1,38 +0,0 @@
-/* SPDX-License-Identifier: GPL-2.0-only */
-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Bengt Jonsson <bengt.g.jonsson@stericsson.com> for ST-Ericsson
- *
- * Interface to power domain regulators on DB8500
- */
-
-#ifndef __REGULATOR_H__
-#define __REGULATOR_H__
-
-/* Number of DB8500 regulators and regulator enumeration */
-enum db8500_regulator_id {
-	DB8500_REGULATOR_VAPE,
-	DB8500_REGULATOR_VARM,
-	DB8500_REGULATOR_VMODEM,
-	DB8500_REGULATOR_VPLL,
-	DB8500_REGULATOR_VSMPS1,
-	DB8500_REGULATOR_VSMPS2,
-	DB8500_REGULATOR_VSMPS3,
-	DB8500_REGULATOR_VRF1,
-	DB8500_REGULATOR_SWITCH_SVAMMDSP,
-	DB8500_REGULATOR_SWITCH_SVAMMDSPRET,
-	DB8500_REGULATOR_SWITCH_SVAPIPE,
-	DB8500_REGULATOR_SWITCH_SIAMMDSP,
-	DB8500_REGULATOR_SWITCH_SIAMMDSPRET,
-	DB8500_REGULATOR_SWITCH_SIAPIPE,
-	DB8500_REGULATOR_SWITCH_SGA,
-	DB8500_REGULATOR_SWITCH_B2R2_MCDE,
-	DB8500_REGULATOR_SWITCH_ESRAM12,
-	DB8500_REGULATOR_SWITCH_ESRAM12RET,
-	DB8500_REGULATOR_SWITCH_ESRAM34,
-	DB8500_REGULATOR_SWITCH_ESRAM34RET,
-	DB8500_NUM_REGULATORS
-};
-
-#endif

-- 
2.55.0

[PATCH v2 19/20] dt-bindings: display: ste,mcde: Deprecate EPOD supply

[Linus Walleij]

Make epod-supply optional and mark it deprecated.

The MCDE should use its power domain instead.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 Documentation/devicetree/bindings/display/ste,mcde.yaml | 5 ++---
 1 file changed, 2 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/display/ste,mcde.yaml b/Documentation/devicetree/bindings/display/ste,mcde.yaml
index 05e7e4ebc882..ee34b65dd13b 100644
--- a/Documentation/devicetree/bindings/display/ste,mcde.yaml
+++ b/Documentation/devicetree/bindings/display/ste,mcde.yaml
@@ -39,7 +39,8 @@ properties:
     maxItems: 1
 
   epod-supply:
-    description: a phandle to the EPOD regulator
+    description: a phandle to the legacy EPOD regulator
+    deprecated: true
 
   vana-supply:
     description: a phandle to the analog voltage regulator
@@ -103,7 +104,6 @@ required:
   - interrupts
   - clocks
   - clock-names
-  - epod-supply
   - vana-supply
 
 additionalProperties: false
@@ -121,7 +121,6 @@ examples:
       reg = <0xa0350000 0x1000>;
       interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
       power-domains = <&pm_domains DOMAIN_B2R2_MCDE>;
-      epod-supply = <&db8500_b2r2_mcde_reg>;
       vana-supply = <&ab8500_ldo_ana_reg>;
       clocks = <&prcmu_clk PRCMU_MCDECLK>,
                <&prcmu_clk PRCMU_LCDCLK>,

-- 
2.55.0

[PATCH v2 20/20] ARM: dts: ux500: Remove DB8500 EPOD regulators

[Linus Walleij]

Delete the obsolete DB8500 EPOD regulator nodes.

Keep the VAPE and VSMPS2 compatibility regulators.

Assisted-by: LLM
Signed-off-by: Linus Walleij <linusw@kernel.org>
---
 arch/arm/boot/dts/st/ste-dbx5x0.dtsi | 92 ------------------------------------
 1 file changed, 92 deletions(-)

diff --git a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
index afba6bee42af..ef5e7b3cefea 100644
--- a/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
+++ b/arch/arm/boot/dts/st/ste-dbx5x0.dtsi
@@ -675,95 +675,15 @@ thermal: thermal@801573c0 {
 				#thermal-sensor-cells = <0>;
 			};
 
-			/*
-			 * TODO: Delete these bogus regulators and replace with power
-			 * domains.
-			 */
 			db8500-prcmu-regulators {
 				compatible = "stericsson,db8500-prcmu-regulator";
 
-				// DB8500_REGULATOR_VAPE
 				db8500_vape_reg: db8500_vape {
 					regulator-always-on;
 				};
 
-				// DB8500_REGULATOR_VARM
-				db8500_varm_reg: db8500_varm {
-				};
-
-				// DB8500_REGULATOR_VMODEM
-				db8500_vmodem_reg: db8500_vmodem {
-				};
-
-				// DB8500_REGULATOR_VPLL
-				db8500_vpll_reg: db8500_vpll {
-				};
-
-				// DB8500_REGULATOR_VSMPS1
-				db8500_vsmps1_reg: db8500_vsmps1 {
-				};
-
-				// DB8500_REGULATOR_VSMPS2
 				db8500_vsmps2_reg: db8500_vsmps2 {
 				};
-
-				// DB8500_REGULATOR_VSMPS3
-				db8500_vsmps3_reg: db8500_vsmps3 {
-				};
-
-				// DB8500_REGULATOR_VRF1
-				db8500_vrf1_reg: db8500_vrf1 {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SVAMMDSP
-				db8500_sva_mmdsp_reg: db8500_sva_mmdsp {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SVAMMDSPRET
-				db8500_sva_mmdsp_ret_reg: db8500_sva_mmdsp_ret {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SVAPIPE
-				db8500_sva_pipe_reg: db8500_sva_pipe {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SIAMMDSP
-				db8500_sia_mmdsp_reg: db8500_sia_mmdsp {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SIAMMDSPRET
-				db8500_sia_mmdsp_ret_reg: db8500_sia_mmdsp_ret {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SIAPIPE
-				db8500_sia_pipe_reg: db8500_sia_pipe {
-				};
-
-				// DB8500_REGULATOR_SWITCH_SGA
-				db8500_sga_reg: db8500_sga {
-					vin-supply = <&db8500_vape_reg>;
-				};
-
-				// DB8500_REGULATOR_SWITCH_B2R2_MCDE
-				db8500_b2r2_mcde_reg: db8500_b2r2_mcde {
-					vin-supply = <&db8500_vape_reg>;
-				};
-
-				// DB8500_REGULATOR_SWITCH_ESRAM12
-				db8500_esram12_reg: db8500_esram12 {
-				};
-
-				// DB8500_REGULATOR_SWITCH_ESRAM12RET
-				db8500_esram12_ret_reg: db8500_esram12_ret {
-				};
-
-				// DB8500_REGULATOR_SWITCH_ESRAM34
-				db8500_esram34_reg: db8500_esram34 {
-				};
-
-				// DB8500_REGULATOR_SWITCH_ESRAM34RET
-				db8500_esram34_ret_reg: db8500_esram34_ret {
-				};
 			};
 		};
 
@@ -1121,8 +1041,6 @@ msp0: msp@80123000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80123000 0x1000>;
 			interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>;
-			/* TODO: delete and replace with power-domain handling */
-			v-ape-supply = <&db8500_vape_reg>;
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			dmas = <&dma 31 0 0x12>, /* Logical - DevToMem - HighPrio */
@@ -1140,8 +1058,6 @@ msp1: msp@80124000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80124000 0x1000>;
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-			/* TODO: delete and replace with power-domain handling */
-			v-ape-supply = <&db8500_vape_reg>;
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			/* This DMA channel only exist on DB8500 v1 */
@@ -1160,8 +1076,6 @@ msp2: msp@80117000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80117000 0x1000>;
 			interrupts = <GIC_SPI 98 IRQ_TYPE_LEVEL_HIGH>;
-			/* TODO: delete and replace with power-domain handling */
-			v-ape-supply = <&db8500_vape_reg>;
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			dmas = <&dma 14 0 0x12>, /* Logical  - DevToMem - HighPrio */
@@ -1180,8 +1094,6 @@ msp3: msp@80125000 {
 			compatible = "stericsson,ux500-msp-i2s";
 			reg = <0x80125000 0x1000>;
 			interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>;
-			/* TODO: delete and replace with power-domain handling */
-			v-ape-supply = <&db8500_vape_reg>;
 			power-domains = <&pm_domains DOMAIN_VAPE>;
 
 			/* This DMA channel only exist on DB8500 v2 */
@@ -1225,8 +1137,6 @@ gpu@a0300000 {
 			clocks = <&prcmu_clk PRCMU_ACLK>, <&prcmu_clk PRCMU_SGACLK>;
 			clock-names = "bus", "core";
 			power-domains = <&pm_domains DOMAIN_SGA>;
-			/* TODO: delete and replace with power-domain handling */
-			mali-supply = <&db8500_sga_reg>;
 		};
 
 		mcde@a0350000 {
@@ -1234,8 +1144,6 @@ mcde@a0350000 {
 			reg = <0xa0350000 0x1000>;
 			interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>;
 			power-domains = <&pm_domains DOMAIN_B2R2_MCDE>;
-			/* TODO: delete and replace with power-domain handling */
-			epod-supply = <&db8500_b2r2_mcde_reg>;
 			clocks = <&prcmu_clk PRCMU_MCDECLK>, /* Main MCDE clock */
 				 <&prcmu_clk PRCMU_LCDCLK>, /* LCD clock */
 				 <&prcmu_clk PRCMU_PLLDSI>; /* HDMI clock */

-- 
2.55.0

Re: [PATCH v2 18/20] mfd/regulator: db8500-prcmu: Remove EPOD regulators

[Mark Brown]

[-- Attachment #1: Type: text/plain, Size: 280 bytes --]

On Mon, Sep 14, 2026 at 01:54:46PM +0200, Linus Walleij wrote:
> Remove the obsolete DB8500 PRCMU regulator drivers.
> 
> Drop the regulator build hooks and the db8500-prcmu-regulators MFD
> cell now that EPODs are power domains.

Acked-by: Mark Brown <broonie@kernel.org>

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 488 bytes --]

Re: [PATCH v2 16/20] misc: sram: Enable runtime PM

[Frank Li]

On Mon, Sep 14, 2026 at 01:54:44PM +0200, Linus Walleij wrote:
> Enable runtime PM for generic SRAM devices after probe has initialized
> the SRAM mappings and partitions.
>
> This lets SRAM devices with attached power domains be managed through
> runtime PM references from their consumers.
>
> Assisted-by: LLM
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---

Reviewed-by: Frank Li <Frank.Li@nxp.com>

>  drivers/misc/sram.c | 5 +++++
>  1 file changed, 5 insertions(+)
>
> diff --git a/drivers/misc/sram.c b/drivers/misc/sram.c
> index c8990e83a65a..7f19dca7b818 100644
> --- a/drivers/misc/sram.c
> +++ b/drivers/misc/sram.c
> @@ -13,6 +13,7 @@
>  #include <linux/of.h>
>  #include <linux/of_address.h>
>  #include <linux/platform_device.h>
> +#include <linux/pm_runtime.h>
>  #include <linux/regmap.h>
>  #include <linux/slab.h>
>  #include <linux/mfd/syscon.h>
> @@ -425,6 +426,10 @@ static int sram_probe(struct platform_device *pdev)
>  			goto err_free_partitions;
>  	}
>
> +	ret = devm_pm_runtime_set_active_enabled(&pdev->dev);
> +	if (ret)
> +		goto err_free_partitions;
> +
>  	if (sram->pool)
>  		dev_dbg(sram->dev, "SRAM pool: %zu KiB @ 0x%p\n",
>  			gen_pool_size(sram->pool) / 1024, sram->virt_base);
>
> --
> 2.55.0
>

Re: [PATCH v2 17/20] dmaengine: ste_dma40: Use power domain for LCLA SRAM

[Frank Li]

On Mon, Sep 14, 2026 at 01:54:45PM +0200, Linus Walleij wrote:
> Replace the LCLA ESRAM regulator with runtime PM.
>
> Use the SRAM device that owns the ESRAM34 power domain.
>
> Hold that domain while DMA transfers are active. The DMA controller is
> runtime PM IRQ-safe, so keep taking explicit LCLA runtime PM references
> from the descriptor preparation path instead of relying on a runtime PM
> device link from the atomic transfer path.
>
> Add a stateless device link so system PM keeps the DMA controller ordered
> after the LCLA SRAM supplier.
>
> Suggested-by: Frank Li <Frank.li@oss.nxp.com>
> Assisted-by: LLM
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  drivers/dma/ste_dma40.c | 130 ++++++++++++++++++++++++++++++++----------------
>  1 file changed, 88 insertions(+), 42 deletions(-)
>
> diff --git a/drivers/dma/ste_dma40.c b/drivers/dma/ste_dma40.c
> index eda3f91741ed..2841af5b160b 100644
> --- a/drivers/dma/ste_dma40.c
> +++ b/drivers/dma/ste_dma40.c
> @@ -21,8 +21,8 @@
>  #include <linux/of.h>
>  #include <linux/of_address.h>
>  #include <linux/of_dma.h>
> +#include <linux/of_platform.h>
>  #include <linux/amba/bus.h>
> -#include <linux/regulator/consumer.h>
>
>  #include "dmaengine.h"
>  #include "ste_dma40.h"
> @@ -383,6 +383,7 @@ struct d40_lli_pool {
>   * @node: List entry.
>   * @is_in_client_list: true if the client owns this descriptor.
>   * @cyclic: true if this is a cyclic job
> + * @lcla_pm_active: LCLA SRAM power domain is held for this descriptor.
>   *
>   * This descriptor is used for both logical and physical transfers.
>   */
> @@ -402,6 +403,7 @@ struct d40_desc {
>
>  	bool				 is_in_client_list;
>  	bool				 cyclic;
> +	bool				 lcla_pm_active;
>  };
>
>  /**
> @@ -571,7 +573,8 @@ struct d40_gen_dmac {
>   * to phy_chans entries.
>   * @plat_data: Pointer to provided platform_data which is the driver
>   * configuration.
> - * @lcpa_regulator: Pointer to hold the regulator for the esram bank for lcla.
> + * @lcla_dev: SRAM device for the ESRAM bank used by LCLA.
> + * @lcla_link: Device link to keep system PM ordered against LCLA.
>   * @phy_res: Vector containing all physical channels.
>   * @lcla_pool: lcla pool settings and data.
>   * @lcpa_base: The virtual mapped address of LCPA.
> @@ -606,7 +609,8 @@ struct d40_base {
>  	struct d40_chan			**lookup_log_chans;
>  	struct d40_chan			**lookup_phy_chans;
>  	struct stedma40_platform_data	 *plat_data;
> -	struct regulator		 *lcpa_regulator;
> +	struct device			 *lcla_dev;
> +	struct device_link		 *lcla_link;
>  	/* Physical half channels */
>  	struct d40_phy_res		 *phy_res;
>  	struct d40_lcla_pool		  lcla_pool;
> @@ -628,6 +632,36 @@ static struct device *chan2dev(struct d40_chan *d40c)
>  	return &d40c->chan.dev->device;
>  }
>
> +static void d40_transfer_runtime_get(struct d40_base *base)
> +{
> +	pm_runtime_get_sync(base->dev);
> +}
> +
> +static int d40_lcla_runtime_get(struct d40_base *base)
> +{
> +	if (!base->lcla_dev)
> +		return 0;
> +
> +	return pm_runtime_resume_and_get(base->lcla_dev);
> +}
> +
> +static void d40_desc_lcla_runtime_put(struct d40_chan *d40c,
> +				      struct d40_desc *d40d)
> +{
> +	struct d40_base *base = d40c->base;
> +
> +	if (!d40d->lcla_pm_active)
> +		return;
> +
> +	d40d->lcla_pm_active = false;
> +	pm_runtime_put(base->lcla_dev);
> +}
> +
> +static void d40_transfer_runtime_put(struct d40_base *base)
> +{
> +	pm_runtime_put_autosuspend(base->dev);
> +}
> +
>  static bool chan_is_physical(struct d40_chan *chan)
>  {
>  	return chan->log_num == D40_PHY_CHAN;
> @@ -818,6 +852,7 @@ static void d40_desc_free(struct d40_chan *d40c, struct d40_desc *d40d)
>
>  	d40_pool_lli_free(d40c, d40d);
>  	d40_lcla_free_all(d40c, d40d);
> +	d40_desc_lcla_runtime_put(d40c, d40d);
>  	kmem_cache_free(d40c->base->desc_slab, d40d);
>  }
>
> @@ -1516,7 +1551,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
>  	if (d40d != NULL) {
>  		if (!d40c->busy) {
>  			d40c->busy = true;
> -			pm_runtime_get_sync(d40c->base->dev);
> +			d40_transfer_runtime_get(d40c->base);
>  		}
>
>  		/* Remove from queue */
> @@ -1535,6 +1570,7 @@ static struct d40_desc *d40_queue_start(struct d40_chan *d40c)
>  			d40_desc_remove(d40d);
>  			d40_desc_free(d40c, d40d);
>  			d40c->busy = false;
> +			d40_transfer_runtime_put(d40c->base);
>  			return ERR_PTR(err);
>  		}
>  	}
> @@ -1583,7 +1619,7 @@ static void dma_tc_handle(struct d40_chan *d40c)
>  		if (d40_queue_start(d40c) == NULL) {
>  			d40c->busy = false;
>
> -			pm_runtime_put_autosuspend(d40c->base->dev);
> +			d40_transfer_runtime_put(d40c->base);
>  		}
>
>  		d40_desc_remove(d40d);
> @@ -1637,6 +1673,7 @@ static void dma_tasklet(struct tasklet_struct *t)
>  		} else if (!d40d->is_in_client_list) {
>  			d40_desc_remove(d40d);
>  			d40_lcla_free_all(d40c, d40d);
> +			d40_desc_lcla_runtime_put(d40c, d40d);
>  			list_add_tail(&d40d->node, &d40c->client);
>  			d40d->is_in_client_list = true;
>  		}
> @@ -2067,7 +2104,7 @@ static int d40_free_dma(struct d40_chan *d40c)
>  		d40c->base->lookup_phy_chans[phy->num] = NULL;
>
>  	if (d40c->busy)
> -		pm_runtime_put_autosuspend(d40c->base->dev);
> +		d40_transfer_runtime_put(d40c->base);
>
>  	d40c->busy = false;
>  	d40c->phy_chan = NULL;
> @@ -2246,6 +2283,7 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
>  	dma_addr_t dst_dev_addr;
>  	struct d40_desc *desc;
>  	unsigned long flags;
> +	bool got_lcla_pm = false;
>  	int ret;
>
>  	if (!chan->phy_chan) {
> @@ -2255,11 +2293,20 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
>
>  	d40_set_runtime_config_write(dchan, &chan->slave_config, direction);
>
> +	ret = d40_lcla_runtime_get(chan->base);
> +	if (ret) {
> +		chan_err(chan, "Failed to enable LCLA power domain\n");
> +		return NULL;
> +	}
> +	got_lcla_pm = !!chan->base->lcla_dev;
> +
>  	spin_lock_irqsave(&chan->lock, flags);
>
>  	desc = d40_prep_desc(chan, sg_src, sg_len, dma_flags);
>  	if (desc == NULL)
>  		goto unlock;
> +	desc->lcla_pm_active = got_lcla_pm;
> +	got_lcla_pm = false;
>
>  	if (sg_next(&sg_src[sg_len - 1]) == sg_src)
>  		desc->cyclic = true;
> @@ -2297,6 +2344,8 @@ d40_prep_sg(struct dma_chan *dchan, struct scatterlist *sg_src,
>  	d40_desc_free(chan, desc);
>   unlock:
>  	spin_unlock_irqrestore(&chan->lock, flags);
> +	if (got_lcla_pm)
> +		pm_runtime_put(chan->base->lcla_dev);
>  	return NULL;
>  }
>
> @@ -2628,7 +2677,7 @@ static int d40_terminate_all(struct dma_chan *chan)
>  	d40_term_all(d40c);
>  	pm_runtime_put_autosuspend(d40c->base->dev);
>  	if (d40c->busy)
> -		pm_runtime_put_autosuspend(d40c->base->dev);
> +		d40_transfer_runtime_put(d40c->base);
>  	d40c->busy = false;
>
>  	spin_unlock_irqrestore(&d40c->lock, flags);
> @@ -2931,29 +2980,11 @@ static int __init d40_dmaengine_init(struct d40_base *base,
>  #ifdef CONFIG_PM_SLEEP
>  static int dma40_suspend(struct device *dev)
>  {
> -	struct d40_base *base = dev_get_drvdata(dev);
> -	int ret;
> -
> -	ret = pm_runtime_force_suspend(dev);
> -	if (ret)
> -		return ret;
> -
> -	if (base->lcpa_regulator)
> -		ret = regulator_disable(base->lcpa_regulator);
> -	return ret;
> +	return pm_runtime_force_suspend(dev);
>  }
>
>  static int dma40_resume(struct device *dev)
>  {
> -	struct d40_base *base = dev_get_drvdata(dev);
> -	int ret = 0;
> -
> -	if (base->lcpa_regulator) {
> -		ret = regulator_enable(base->lcpa_regulator);
> -		if (ret)
> -			return ret;
> -	}
> -
>  	return pm_runtime_force_resume(dev);
>  }
>  #endif
> @@ -3509,7 +3540,10 @@ static int __init d40_probe(struct platform_device *pdev)
>  	struct device *dev = &pdev->dev;
>  	struct device_node *np = pdev->dev.of_node;
>  	struct device_node *np_lcpa;
> +	struct device_node *np_lcla;
> +	struct device_node *np_lcla_parent;
>  	struct d40_base *base;
> +	struct platform_device *lcla_pdev;
>  	struct resource *res;
>  	struct resource res_lcpa;
>  	int num_reserved_chans;
> @@ -3610,21 +3644,32 @@ static int __init d40_probe(struct platform_device *pdev)
>  	irq_requested = true;
>
>  	if (base->plat_data->use_esram_lcla) {
> +		np_lcla = of_parse_phandle(np, "sram", 1);
> +		if (!np_lcla) {
> +			dev_err(dev, "no LCLA SRAM node\n");
> +			ret = -EINVAL;
> +			goto destroy_cache;
> +		}

sram is used at many place, is it good to put into
drivers/of/property.c DEFINE_SIMPLE_PROP to avoid set up device link by
each driver?

Frank

>
> -		base->lcpa_regulator = regulator_get(base->dev, "lcla_esram");
> -		if (IS_ERR(base->lcpa_regulator)) {
> -			d40_err(dev, "Failed to get lcpa_regulator\n");
> -			ret = PTR_ERR(base->lcpa_regulator);
> -			base->lcpa_regulator = NULL;
> +		np_lcla_parent = of_get_parent(np_lcla);
> +		of_node_put(np_lcla);
> +		if (!np_lcla_parent) {
> +			dev_err(dev, "no LCLA SRAM parent node\n");
> +			ret = -EINVAL;
>  			goto destroy_cache;
>  		}
>
> -		ret = regulator_enable(base->lcpa_regulator);
> -		if (ret) {
> -			d40_err(dev,
> -				"Failed to enable lcpa_regulator\n");
> -			regulator_put(base->lcpa_regulator);
> -			base->lcpa_regulator = NULL;
> +		lcla_pdev = of_find_device_by_node(np_lcla_parent);
> +		of_node_put(np_lcla_parent);
> +		if (!lcla_pdev) {
> +			ret = -EPROBE_DEFER;
> +			goto destroy_cache;
> +		}
> +		base->lcla_dev = &lcla_pdev->dev;
> +		base->lcla_link = device_link_add(dev, base->lcla_dev,
> +						  DL_FLAG_STATELESS);
> +		if (!base->lcla_link) {
> +			ret = -ENODEV;
>  			goto destroy_cache;
>  		}
>  	}
> @@ -3663,16 +3708,17 @@ static int __init d40_probe(struct platform_device *pdev)
>  				 SZ_1K * base->num_phy_chans,
>  				 DMA_TO_DEVICE);
>
> -	if (!base->lcla_pool.base_unaligned && base->lcla_pool.base)
> +	if (!base->lcla_pool.base_unaligned && base->lcla_pool.base &&
> +	    base->lcla_pool.pages)
>  		free_pages((unsigned long)base->lcla_pool.base,
>  			   base->lcla_pool.pages);
>
>  	kfree(base->lcla_pool.base_unaligned);
>
> -	if (base->lcpa_regulator) {
> -		regulator_disable(base->lcpa_regulator);
> -		regulator_put(base->lcpa_regulator);
> -	}
> +	if (base->lcla_link)
> +		device_link_del(base->lcla_link);
> +	if (base->lcla_dev)
> +		put_device(base->lcla_dev);
>  	if (irq_requested)
>  		free_irq(base->irq, base);
>  	if (runtime_pm_enabled)
>
> --
> 2.55.0
>

Re: [PATCH v2 01/20] dt-bindings: power: Convert Ux500 PM domains to schema

[Rob Herring (Arm)]

On Mon, 14 Sep 2026 13:54:29 +0200, Linus Walleij wrote:
> Convert the legacy Ux500 power domain text binding to YAML.
> 
> Move it under bindings/power.
> 
> Reference the generic power-domain schema.
> 
> Update MAINTAINERS for the new path.
> 
> Assisted-by: LLM
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  .../devicetree/bindings/arm/ux500/power_domain.txt | 35 ----------------
>  .../power/stericsson,ux500-pm-domains.yaml         | 46 ++++++++++++++++++++++
>  MAINTAINERS                                        |  1 +
>  3 files changed, 47 insertions(+), 35 deletions(-)
> 

My bot found errors running 'make dt_binding_check' on your patch:

yamllint warnings/errors:

dtschema/dtc warnings/errors:
Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.example.dts:25.28-28.11: Warning (unit_address_vs_reg): /example-0/sdi0_per1@80126000: node has a unit name, but no reg or ranges property
Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.example.dtb: sdi0_per1@80126000 (arm,pl18x): $nodename:0: 'sdi0_per1@80126000' does not match '^mmc(@.*)?$'
	from schema $id: http://devicetree.org/schemas/mmc/arm,pl18x.yaml
Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.example.dtb: sdi0_per1@80126000 (arm,pl18x): 'anyOf' conditional failed, one must be fixed:
	'interrupts' is a required property
	'interrupts-extended' is a required property
	from schema $id: http://devicetree.org/schemas/mmc/arm,pl18x.yaml
Documentation/devicetree/bindings/power/stericsson,ux500-pm-domains.example.dtb: sdi0_per1@80126000 (arm,pl18x): 'reg' is a required property
	from schema $id: http://devicetree.org/schemas/mmc/arm,pl18x.yaml

doc reference errors (make refcheckdocs):

See https://patchwork.kernel.org/project/devicetree/patch/20260914-ux500-power-domains-v7-1-v2-1-9d0c17e1f816@kernel.org

The base for the series is generally the latest rc1. A different dependency
should be noted in *this* patch.

If you already ran 'make dt_binding_check' and didn't see the above
error(s), then make sure 'yamllint' is installed and dt-schema is up to
date:

pip3 install dtschema --upgrade

Please check and re-submit after running the above command yourself. Note
that DT_SCHEMA_FILES can be set to your schema file to speed up checking
your schema. However, it must be unset to test all examples with your schema.

Re: [PATCH v2 02/20] dt-bindings: arm: ux500: Drop NR_DOMAINS

[Krzysztof Kozlowski]

On Mon, Sep 14, 2026 at 01:54:30PM +0200, Linus Walleij wrote:
> Keep the internal Ux500 PM domain count local to the only driver
> that uses it.
> 
> Do not expose this implementation detail through the DT binding header.
> 
> Assisted-by: LLM
> Reported-by: Krzysztof Kozlowski <krzk@kernel.org>

I would say Suggested-by, because it is not a bug, just preference.

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v2 03/20] dt-bindings: arm: Add the actual power domains on U8500

[Krzysztof Kozlowski]

On Mon, Sep 14, 2026 at 01:54:31PM +0200, Linus Walleij wrote:
> This file has been left in an unfinished state just defining
> the root power domain for the U8500 SoC. Fix it up by adding
> the actual existing power domains in this SoC.
> 
> The PRCMU code and old regulator driver is mentioning some
> *_RET domains, this means "retention" and is a state in the
> domain and not a domain of its own.
> 
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  include/dt-bindings/arm/ux500_pm_domains.h | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v2 04/20] dt-bindings: mfd: db8500-prcmu: Relax EPOD regulators

[Krzysztof Kozlowski]

On Mon, Sep 14, 2026 at 01:54:32PM +0200, Linus Walleij wrote:
> Allow the VAPE and VSMPS2 compatibility regulators to carry power-domains.
> 
> Stop requiring the EPOD regulator child nodes that are being replaced
> by generic power domains.
> 
> Assisted-by: LLM
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  .../bindings/mfd/stericsson,db8500-prcmu.yaml      | 24 ++++++----------------
>  1 file changed, 6 insertions(+), 18 deletions(-)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v2 05/20] dt-bindings: display: ste,mcde: Allow power domains

[Krzysztof Kozlowski]

On Mon, Sep 14, 2026 at 01:54:33PM +0200, Linus Walleij wrote:
> Document the MCDE power domain.
> 
> Keep the legacy EPOD regulator binding unchanged for now.
> 
> Assisted-by: LLM
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  Documentation/devicetree/bindings/display/ste,mcde.yaml | 5 +++++
>  1 file changed, 5 insertions(+)

Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v2 08/20] dt-bindings: cache: l2c2x0: Document power domain

[Krzysztof Kozlowski]

On Mon, Sep 14, 2026 at 01:54:36PM +0200, Linus Walleij wrote:
> Describe the optional power domain for cache controllers.

It is already described.

Best regards,
Krzysztof

Re: [PATCH v2 17/20] dmaengine: ste_dma40: Use power domain for LCLA SRAM

[Linus Walleij]

On Mon, Sep 14, 2026 at 11:02 PM Frank Li <Frank.li@oss.nxp.com> wrote:
> On Mon, Sep 14, 2026 at 01:54:45PM +0200, Linus Walleij wrote:

> >       if (base->plat_data->use_esram_lcla) {
> > +             np_lcla = of_parse_phandle(np, "sram", 1);
> > +             if (!np_lcla) {
> > +                     dev_err(dev, "no LCLA SRAM node\n");
> > +                     ret = -EINVAL;
> > +                     goto destroy_cache;
> > +             }
>
> sram is used at many place, is it good to put into
> drivers/of/property.c DEFINE_SIMPLE_PROP to avoid set up device link by
> each driver?

I have absolutely no idea if that is a good idea or how to
even use that macro.

But Saravana will know, so let's ask him!

Yours,
Linus Walleij

Re: [PATCH v2 09/20] dt-bindings: arm: pmu: Allow power domains

[Rob Herring]

On Mon, Sep 14, 2026 at 01:54:37PM +0200, Linus Walleij wrote:
> Allow ARM PMU nodes to reference their power domain.
> 
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  Documentation/devicetree/bindings/arm/pmu.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/arm/pmu.yaml b/Documentation/devicetree/bindings/arm/pmu.yaml
> index f47baaefcdac..305c1a9668f4 100644
> --- a/Documentation/devicetree/bindings/arm/pmu.yaml
> +++ b/Documentation/devicetree/bindings/arm/pmu.yaml
> @@ -88,6 +88,9 @@ properties:
>      # Don't know how many CPUs, so no constraints to specify
>      description: 1 per-cpu interrupt (PPI) or 1 interrupt per core.
>  
> +  power-domains:
> +    maxItems: 1

The PMUs are per core, so you really need to support more than 1. 
However, I think the PMUs would always be part of the core domain and 
the A9 docs[1] don't show any sort of PMU domain.

We already support power-domains in the CPU nodes, wouldn't that be more 
accurate?

Rob

[1] https://support.arm.com/documentation/ddi0407/b/clocking--resets--and-power-management/iem-support/cortex-a9-mpcore-power-domains

Re: [PATCH v2 10/20] dt-bindings: clock: stericsson,u8500-clks: Allow power domains

[Rob Herring (Arm)]

On Mon, 14 Sep 2026 13:54:38 +0200, Linus Walleij wrote:
> Allow the DB8500 clock controller node to reference its power domain.
> 
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  Documentation/devicetree/bindings/clock/stericsson,u8500-clks.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 11/20] dt-bindings: timer: arm,twd-timer: Allow power domains

[Rob Herring (Arm)]

On Mon, 14 Sep 2026 13:54:39 +0200, Linus Walleij wrote:
> Allow TWD timer nodes to reference their power domain.
> 
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  Documentation/devicetree/bindings/timer/arm,twd-timer.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 12/20] dt-bindings: watchdog: arm,twd-wdt: Allow power domains

[Rob Herring (Arm)]

On Mon, 14 Sep 2026 13:54:40 +0200, Linus Walleij wrote:
> Allow TWD watchdog nodes to reference their power domain.
> 
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  Documentation/devicetree/bindings/watchdog/arm,twd-wdt.yaml | 3 +++
>  1 file changed, 3 insertions(+)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 19/20] dt-bindings: display: ste,mcde: Deprecate EPOD supply

[Rob Herring (Arm)]

On Mon, 14 Sep 2026 13:54:47 +0200, Linus Walleij wrote:
> Make epod-supply optional and mark it deprecated.
> 
> The MCDE should use its power domain instead.
> 
> Assisted-by: LLM
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  Documentation/devicetree/bindings/display/ste,mcde.yaml | 5 ++---
>  1 file changed, 2 insertions(+), 3 deletions(-)
> 

Acked-by: Rob Herring (Arm) <robh@kernel.org>

Re: [PATCH v2 18/20] mfd/regulator: db8500-prcmu: Remove EPOD regulators

[Lee Jones]

On Mon, 14 Sep 2026, Linus Walleij wrote:

> Remove the obsolete DB8500 PRCMU regulator drivers.
> 
> Drop the regulator build hooks and the db8500-prcmu-regulators MFD
> cell now that EPODs are power domains.
> 
> Assisted-by: LLM
> Acked-by: Mark Brown <broonie@kernel.org>
> Signed-off-by: Linus Walleij <linusw@kernel.org>
> ---
>  drivers/mfd/db8500-prcmu.c             | 239 ----------------
>  drivers/regulator/Kconfig              |  12 -
>  drivers/regulator/Makefile             |   2 -
>  drivers/regulator/db8500-prcmu.c       | 501 ---------------------------------
>  drivers/regulator/dbx500-prcmu.c       | 155 ----------
>  drivers/regulator/dbx500-prcmu.h       |  55 ----
>  include/linux/regulator/db8500-prcmu.h |  38 ---
>  7 files changed, 1002 deletions(-)

Looks good.  What's the plan?

-- 
Lee Jones

Re: [PATCH v2 18/20] mfd/regulator: db8500-prcmu: Remove EPOD regulators

[Linus Walleij]

On Wed, Sep 23, 2026 at 5:20 PM Lee Jones <lee@kernel.org> wrote:

> Looks good.  What's the plan?

I need to address some binding issues, then I'll send out a v3
which I think can be applied.

If you could just apply this one at that point I thin the rest will
trickle in nicely through the Power Domain and SoC trees.

I'll add a blurb to the patch to this effect in v3.

Yours,
Linus Walleij