Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH v6 0/2] gpio: Add Cortina Systems CS75xx GPIO driver
@ 2026-11-19 15:09 Fil Dunsky via B4 Relay
  2026-11-19 15:09 ` [PATCH v6 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller Fil Dunsky via B4 Relay
  2026-11-19 15:09 ` [PATCH v6 2/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
  0 siblings, 2 replies; 3+ messages in thread
From: Fil Dunsky via B4 Relay @ 2026-11-19 15:09 UTC (permalink / raw)
  To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
	Krzysztof Kozlowski, Conor Dooley
  Cc: linux-gpio, devicetree, linux-kernel, linux-arm-kernel,
	Krzysztof Kozlowski, Fil Dunsky

The Cortina Systems CS75xx ("Goldengate G2") SoCs have five banks of 32
GPIO lines, each bank with its own interrupt. This series adds the
binding and a driver based on gpio-mmio; level and edge triggers are
supported, both edges are emulated by flipping the polarity.

Each pin is either a GPIO line or belongs to a peripheral (NAND,
Ethernet, UART, I2C, ...). That choice is made in the global control
block, which is not part of the GPIO controller: as discussed on v1 [1],
the driver does not touch the pin mux and leaves it as the boot loader
set it up, until there is a pin controller driver for that block.
Testing the reset button on the Securifi Almond+ requires selecting
GPIO37 in the global pin mux before gpio-keys is probed; the current
boot path does not provide that setup. The tests used a separate,
board-specific setup step. The GPIO driver does not program the mux.

The driver used to be part of a series with the interrupt controller,
I2C and watchdog drivers and the device tree changes. That series is now
split per subsystem. The driver depends on OF and the generic MMIO GPIO
and IRQ infrastructure, with no dependency on the platform series [2],
which is under review separately. The device tree nodes will follow with
the other CS75xx dts changes once the platform is merged.

There is no public documentation; the register layout comes from the GPL
vendor kernels. Tested on a Securifi Almond+ (CS7542): the reset button
(GPIO 37) works as an active-low gpio-keys input, and the SX8650
touchscreen uses a level-triggered GPIO interrupt.

[1] https://lore.kernel.org/all/20261012-dreamlike-hazily-19bb60326f0a@spud/
[2] https://lore.kernel.org/all/20261114-b4-cs75xx-v7-0-8f17f38821b4@gmail.com/

---
Changes in v6:
- replace the dependency on ARCH_CORTINA_ACCESS || COMPILE_TEST with OF,
  so the GPIO series can be merged independently of the platform series
  (Bartosz); HAS_IOMEM is inherited from the MMIO GPIO driver menu
- build built-in and modular on ARM and x86-64 with COMPILE_TEST=n,
  without the platform series; the driver code is unchanged
- Link to v5: https://patch.msgid.link/20261119-cs75xx-gpio-v5-0-8d14f2bb614b@gmail.com

Changes in v5:
- explain that ARCH_CORTINA_ACCESS is introduced by the platform series;
  COMPILE_TEST allows building this driver without that series
- correct the pin mux setup required for testing the Almond+ reset button
- clear the interrupt status after changing the trigger type, so that
  unmasking an edge interrupt does not fire a stale event (sashiko-bot)
- collect Reviewed-by tags; Linus, I kept yours over the one-line change
  above
- Link to v4: https://patch.msgid.link/20261116-cs75xx-gpio-v4-0-ad80a944e966@gmail.com

Changes in v4:
- rebase on v7.4-rc1
- split out of "Cortina Systems CS75xx: interrupt controller, GPIO, I2C
  and TWD watchdog" so that each driver can go through its own tree; no
  longer based on the platform series
- the pin mux registers are not part of the GPIO controller (Conor): the
  binding has a single reg entry and the driver no longer switches the
  pin mux when a line is requested
  (Rob, your Reviewed-by on v3 is not carried because of this change)
- switch a line to input for an interrupt only when it is not requested;
  flip the polarity of a both-edges line after the ack, so that an edge
  in between is not lost (sashiko-bot)
- drop the gpio_chip owner, gpiolib sets it; sort the Makefile entry
- Link to v3: https://patch.msgid.link/20261013-b4-cs75xx-s2-v3-0-181bb0d23f4c@gmail.com

Changes in v3:
- rebase on v6 of the platform series
- Link to v2: https://patch.msgid.link/20261013-b4-cs75xx-s2-v2-0-94f8c0a90cda@gmail.com

Changes in v2:
- rebase on v5 of the platform series
- do not include <linux/mod_devicetable.h> (Uwe)
- update the both-edges mask only for a valid trigger type and test it
  under the lock in the interrupt handler; refuse more than 32 lines
  (sashiko-bot)
- Link to v1: https://patch.msgid.link/20261012-b4-cs75xx-s2-v1-0-8a7641b7b79c@gmail.com

To: Linus Walleij <linusw@kernel.org>
To: Bartosz Golaszewski <brgl@kernel.org>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
Cc: linux-gpio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org

---
Fil Dunsky (2):
      dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller
      gpio: Add Cortina Systems CS75xx GPIO driver

 .../bindings/gpio/cortina,cs7542-gpio.yaml         |  65 +++++
 drivers/gpio/Kconfig                               |  12 +
 drivers/gpio/Makefile                              |   1 +
 drivers/gpio/gpio-cs75xx.c                         | 283 +++++++++++++++++++++
 4 files changed, 361 insertions(+)
---
base-commit: 6628e7d4c6b25c8d18f1345e3a20d21829aae7e4
change-id: 20261015-cs75xx-gpio-ed0a37ee4a68

Best regards,
--  
Fil Dunsky <filipp.dunsky@gmail.com>




^ permalink raw reply	[flat|nested] 3+ messages in thread

* [PATCH v6 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller
  2026-11-19 15:09 [PATCH v6 0/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
@ 2026-11-19 15:09 ` Fil Dunsky via B4 Relay
  2026-11-19 15:09 ` [PATCH v6 2/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
  1 sibling, 0 replies; 3+ messages in thread
From: Fil Dunsky via B4 Relay @ 2026-11-19 15:09 UTC (permalink / raw)
  To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
	Krzysztof Kozlowski, Conor Dooley
  Cc: linux-gpio, devicetree, linux-kernel, linux-arm-kernel,
	Krzysztof Kozlowski, Fil Dunsky

From: Fil Dunsky <filipp.dunsky@gmail.com>

The Cortina Systems CS75xx SoCs have five banks of 32 GPIO lines. Each
pin is shared between a GPIO line and a peripheral function; the pin
mux lives in the global control block and is not described here.

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
---
 .../bindings/gpio/cortina,cs7542-gpio.yaml         | 65 ++++++++++++++++++++++
 1 file changed, 65 insertions(+)

diff --git a/Documentation/devicetree/bindings/gpio/cortina,cs7542-gpio.yaml b/Documentation/devicetree/bindings/gpio/cortina,cs7542-gpio.yaml
new file mode 100644
index 000000000..faa302180
--- /dev/null
+++ b/Documentation/devicetree/bindings/gpio/cortina,cs7542-gpio.yaml
@@ -0,0 +1,65 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/gpio/cortina,cs7542-gpio.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Cortina Systems CS7542 GPIO controller
+
+maintainers:
+  - Fil Dunsky <filipp.dunsky@gmail.com>
+
+description:
+  The Cortina Systems CS75xx (Goldengate G2) SoCs have five banks of 32
+  GPIO lines, each with its own interrupt. Every pin is shared between a
+  GPIO line and a peripheral function; the choice is made in the global
+  control block and is not part of the GPIO controller.
+
+properties:
+  compatible:
+    const: cortina,cs7542-gpio
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  gpio-controller: true
+
+  "#gpio-cells":
+    const: 2
+
+  gpio-line-names:
+    maxItems: 32
+
+  gpio-reserved-ranges: true
+
+  interrupt-controller: true
+
+  "#interrupt-cells":
+    const: 2
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - gpio-controller
+  - "#gpio-cells"
+  - interrupt-controller
+  - "#interrupt-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    gpio@f00701f0 {
+        compatible = "cortina,cs7542-gpio";
+        reg = <0xf00701f0 0x20>;
+        interrupt-parent = <&intc>;
+        interrupts = <7>;
+        gpio-controller;
+        #gpio-cells = <2>;
+        interrupt-controller;
+        #interrupt-cells = <2>;
+    };

-- 
2.53.0




^ permalink raw reply related	[flat|nested] 3+ messages in thread

* [PATCH v6 2/2] gpio: Add Cortina Systems CS75xx GPIO driver
  2026-11-19 15:09 [PATCH v6 0/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
  2026-11-19 15:09 ` [PATCH v6 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller Fil Dunsky via B4 Relay
@ 2026-11-19 15:09 ` Fil Dunsky via B4 Relay
  1 sibling, 0 replies; 3+ messages in thread
From: Fil Dunsky via B4 Relay @ 2026-11-19 15:09 UTC (permalink / raw)
  To: Linus Walleij, Bartosz Golaszewski, Rob Herring,
	Krzysztof Kozlowski, Conor Dooley
  Cc: linux-gpio, devicetree, linux-kernel, linux-arm-kernel,
	Fil Dunsky

From: Fil Dunsky <filipp.dunsky@gmail.com>

Add a driver for the GPIO banks of the Cortina Systems CS75xx SoCs. The
data and direction registers are handled by gpio-mmio; each bank has its
own interrupt with level and edge triggers, both edges are emulated by
flipping the polarity.

A pin only works as a GPIO when the pin mux in the global control block
selects the GPIO function. That is not part of the GPIO controller and
is left to the boot loader until there is a pin controller driver.

The driver depends on OF and generic MMIO GPIO and IRQ support, so it
can be enabled independently of the CS75xx platform series.

Reviewed-by: Linus Walleij <linusw@kernel.org>
Signed-off-by: Fil Dunsky <filipp.dunsky@gmail.com>
---
 drivers/gpio/Kconfig       |  12 ++
 drivers/gpio/Makefile      |   1 +
 drivers/gpio/gpio-cs75xx.c | 283 +++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 296 insertions(+)

diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
index 55e428002..abfb41099 100644
--- a/drivers/gpio/Kconfig
+++ b/drivers/gpio/Kconfig
@@ -300,6 +300,18 @@ config GPIO_CLPS711X
 	help
 	  Say yes here to support GPIO on CLPS711X SoCs.
 
+config GPIO_CS75XX
+	tristate "Cortina Systems CS75xx GPIO support"
+	depends on OF
+	select GPIO_GENERIC
+	select GPIOLIB_IRQCHIP
+	help
+	  Say yes here to support the GPIO banks of the Cortina Systems
+	  CS75xx SoCs, including their interrupts.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called gpio-cs75xx.
+
 config GPIO_DAVINCI
 	tristate "TI Davinci/Keystone GPIO support"
 	default y if ARCH_DAVINCI
diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
index 88f748846..2c2e18ef2 100644
--- a/drivers/gpio/Makefile
+++ b/drivers/gpio/Makefile
@@ -60,6 +60,7 @@ obj-$(CONFIG_GPIO_SNPS_CREG)		+= gpio-creg-snps.o
 obj-$(CONFIG_GPIO_CROS_EC)		+= gpio-cros-ec.o
 obj-$(CONFIG_GPIO_CRYSTAL_COVE)		+= gpio-crystalcove.o
 obj-$(CONFIG_GPIO_CS5535)		+= gpio-cs5535.o
+obj-$(CONFIG_GPIO_CS75XX)		+= gpio-cs75xx.o
 obj-$(CONFIG_GPIO_DA9052)		+= gpio-da9052.o
 obj-$(CONFIG_GPIO_DA9055)		+= gpio-da9055.o
 obj-$(CONFIG_GPIO_DAVINCI)		+= gpio-davinci.o
diff --git a/drivers/gpio/gpio-cs75xx.c b/drivers/gpio/gpio-cs75xx.c
new file mode 100644
index 000000000..733284444
--- /dev/null
+++ b/drivers/gpio/gpio-cs75xx.c
@@ -0,0 +1,283 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Cortina Systems CS75xx GPIO controller
+ *
+ * Each bank has 32 lines with direction, data and interrupt registers.
+ * Whether a pin is driven by the GPIO bank or by its peripheral function
+ * (NAND, Ethernet, UART, ...) is selected in the global control block,
+ * which this driver does not touch: the pin mux is left as the boot loader
+ * set it up.
+ */
+
+#include <linux/bitops.h>
+#include <linux/cleanup.h>
+#include <linux/gpio/driver.h>
+#include <linux/gpio/generic.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+
+#define CS75XX_GPIO_CFG		0x00	/* 1: input, 0: output */
+#define CS75XX_GPIO_OUT		0x04
+#define CS75XX_GPIO_IN		0x08
+#define CS75XX_GPIO_LVL		0x0c	/* 1: high level or rising edge */
+#define CS75XX_GPIO_EDGE	0x10	/* 1: edge, 0: level */
+#define CS75XX_GPIO_IE		0x14
+#define CS75XX_GPIO_INT		0x18	/* write 1 to clear */
+
+struct cs75xx_gpio {
+	struct gpio_generic_chip chip;
+	void __iomem *base;
+	u32 both_edges;
+};
+
+/* Both edges are emulated by flipping the polarity on every interrupt */
+static void cs75xx_gpio_set_polarity(struct cs75xx_gpio *g, u32 mask)
+{
+	u32 lvl = readl(g->base + CS75XX_GPIO_LVL);
+
+	if (readl(g->base + CS75XX_GPIO_IN) & mask)
+		lvl &= ~mask;
+	else
+		lvl |= mask;
+
+	writel(lvl, g->base + CS75XX_GPIO_LVL);
+}
+
+static void cs75xx_gpio_irq_ack(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct cs75xx_gpio *g = gpiochip_get_data(gc);
+	u32 mask = BIT(irqd_to_hwirq(d));
+
+	guard(gpio_generic_lock_irqsave)(&g->chip);
+	writel(mask, g->base + CS75XX_GPIO_INT);
+	/* Arm the opposite edge after the ack, so that it is not lost */
+	if (g->both_edges & mask)
+		cs75xx_gpio_set_polarity(g, mask);
+}
+
+static void cs75xx_gpio_irq_mask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct cs75xx_gpio *g = gpiochip_get_data(gc);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+
+	scoped_guard(gpio_generic_lock_irqsave, &g->chip) {
+		u32 ie = readl(g->base + CS75XX_GPIO_IE);
+
+		writel(ie & ~BIT(hwirq), g->base + CS75XX_GPIO_IE);
+	}
+
+	gpiochip_disable_irq(gc, hwirq);
+}
+
+static void cs75xx_gpio_irq_unmask(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct cs75xx_gpio *g = gpiochip_get_data(gc);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	u32 ie;
+
+	gpiochip_enable_irq(gc, hwirq);
+
+	guard(gpio_generic_lock_irqsave)(&g->chip);
+	/*
+	 * The status of a level interrupt is latched while the line is
+	 * asserted, also after the ack, so it may be stale by now. Clear it,
+	 * it is set again right away if the line is still asserted.
+	 */
+	if (irqd_is_level_type(d))
+		writel(BIT(hwirq), g->base + CS75XX_GPIO_INT);
+	ie = readl(g->base + CS75XX_GPIO_IE);
+	writel(ie | BIT(hwirq), g->base + CS75XX_GPIO_IE);
+}
+
+static int cs75xx_gpio_irq_set_type(struct irq_data *d, unsigned int type)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	struct cs75xx_gpio *g = gpiochip_get_data(gc);
+	u32 mask = BIT(irqd_to_hwirq(d));
+	u32 lvl, edge, both_edges;
+
+	guard(gpio_generic_lock_irqsave)(&g->chip);
+
+	lvl = readl(g->base + CS75XX_GPIO_LVL);
+	edge = readl(g->base + CS75XX_GPIO_EDGE);
+	both_edges = g->both_edges & ~mask;
+
+	switch (type & IRQ_TYPE_SENSE_MASK) {
+	case IRQ_TYPE_LEVEL_LOW:
+		lvl &= ~mask;
+		edge &= ~mask;
+		break;
+	case IRQ_TYPE_LEVEL_HIGH:
+		lvl |= mask;
+		edge &= ~mask;
+		break;
+	case IRQ_TYPE_EDGE_FALLING:
+		lvl &= ~mask;
+		edge |= mask;
+		break;
+	case IRQ_TYPE_EDGE_RISING:
+		lvl |= mask;
+		edge |= mask;
+		break;
+	case IRQ_TYPE_EDGE_BOTH:
+		both_edges |= mask;
+		edge |= mask;
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	g->both_edges = both_edges;
+	writel(lvl, g->base + CS75XX_GPIO_LVL);
+	writel(edge, g->base + CS75XX_GPIO_EDGE);
+	if (g->both_edges & mask)
+		cs75xx_gpio_set_polarity(g, mask);
+	/* The new trigger may have latched the status already, drop it */
+	writel(mask, g->base + CS75XX_GPIO_INT);
+
+	if (type & IRQ_TYPE_LEVEL_MASK)
+		irq_set_handler_locked(d, handle_level_irq);
+	else
+		irq_set_handler_locked(d, handle_edge_irq);
+
+	return 0;
+}
+
+static int cs75xx_gpio_irq_reqres(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+	irq_hw_number_t hwirq = irqd_to_hwirq(d);
+	int ret;
+
+	/*
+	 * The boot loader may leave the line configured as an output. Only
+	 * touch it when nobody else has requested it.
+	 */
+	char *label __free(kfree) = gpiochip_dup_line_label(gc, hwirq);
+	if (IS_ERR(label))
+		return PTR_ERR(label);
+	if (!label) {
+		ret = gc->direction_input(gc, hwirq);
+		if (ret)
+			return ret;
+	}
+
+	return gpiochip_reqres_irq(gc, hwirq);
+}
+
+static void cs75xx_gpio_irq_relres(struct irq_data *d)
+{
+	struct gpio_chip *gc = irq_data_get_irq_chip_data(d);
+
+	gpiochip_relres_irq(gc, irqd_to_hwirq(d));
+}
+
+static const struct irq_chip cs75xx_gpio_irq_chip = {
+	.name			= "cs75xx-gpio",
+	.irq_ack		= cs75xx_gpio_irq_ack,
+	.irq_mask		= cs75xx_gpio_irq_mask,
+	.irq_unmask		= cs75xx_gpio_irq_unmask,
+	.irq_set_type		= cs75xx_gpio_irq_set_type,
+	.irq_request_resources	= cs75xx_gpio_irq_reqres,
+	.irq_release_resources	= cs75xx_gpio_irq_relres,
+	.flags			= IRQCHIP_IMMUTABLE | IRQCHIP_MASK_ON_SUSPEND,
+};
+
+static void cs75xx_gpio_irq_handler(struct irq_desc *desc)
+{
+	struct gpio_chip *gc = irq_desc_get_handler_data(desc);
+	struct cs75xx_gpio *g = gpiochip_get_data(gc);
+	struct irq_chip *chip = irq_desc_get_chip(desc);
+	unsigned long pending;
+	unsigned int offset;
+
+	chained_irq_enter(chip, desc);
+
+	pending = readl(g->base + CS75XX_GPIO_INT) &
+		  readl(g->base + CS75XX_GPIO_IE);
+
+	for_each_set_bit(offset, &pending, gc->ngpio)
+		generic_handle_domain_irq(gc->irq.domain, offset);
+
+	chained_irq_exit(chip, desc);
+}
+
+static int cs75xx_gpio_probe(struct platform_device *pdev)
+{
+	struct gpio_generic_chip_config config;
+	struct device *dev = &pdev->dev;
+	struct gpio_irq_chip *girq;
+	struct cs75xx_gpio *g;
+	int irq, ret;
+
+	g = devm_kzalloc(dev, sizeof(*g), GFP_KERNEL);
+	if (!g)
+		return -ENOMEM;
+
+	g->base = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(g->base))
+		return PTR_ERR(g->base);
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return irq;
+
+	config = (struct gpio_generic_chip_config) {
+		.dev = dev,
+		.sz = 4,
+		.dat = g->base + CS75XX_GPIO_IN,
+		.set = g->base + CS75XX_GPIO_OUT,
+		.dirin = g->base + CS75XX_GPIO_CFG,
+	};
+
+	ret = gpio_generic_chip_init(&g->chip, &config);
+	if (ret)
+		return dev_err_probe(dev, ret, "unable to init generic GPIO\n");
+
+	if (g->chip.gc.ngpio > 32)
+		return dev_err_probe(dev, -EINVAL, "too many lines: %u\n",
+				     g->chip.gc.ngpio);
+
+	/* Mask and clear all interrupts before the parent is set up */
+	writel(0, g->base + CS75XX_GPIO_IE);
+	writel(~0, g->base + CS75XX_GPIO_INT);
+
+	girq = &g->chip.gc.irq;
+	gpio_irq_chip_set_chip(girq, &cs75xx_gpio_irq_chip);
+	girq->parent_handler = cs75xx_gpio_irq_handler;
+	girq->num_parents = 1;
+	girq->parents = devm_kcalloc(dev, 1, sizeof(*girq->parents),
+				     GFP_KERNEL);
+	if (!girq->parents)
+		return -ENOMEM;
+	girq->parents[0] = irq;
+	girq->default_type = IRQ_TYPE_NONE;
+	girq->handler = handle_bad_irq;
+
+	return devm_gpiochip_add_data(dev, &g->chip.gc, g);
+}
+
+static const struct of_device_id cs75xx_gpio_of_match[] = {
+	{ .compatible = "cortina,cs7542-gpio" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, cs75xx_gpio_of_match);
+
+static struct platform_driver cs75xx_gpio_driver = {
+	.probe = cs75xx_gpio_probe,
+	.driver = {
+		.name = "cs75xx-gpio",
+		.of_match_table = cs75xx_gpio_of_match,
+	},
+};
+module_platform_driver(cs75xx_gpio_driver);
+
+MODULE_DESCRIPTION("Cortina Systems CS75xx GPIO driver");
+MODULE_LICENSE("GPL");

-- 
2.53.0




^ permalink raw reply related	[flat|nested] 3+ messages in thread

end of thread, other threads:[~2026-11-19 15:09 UTC | newest]

Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-19 15:09 [PATCH v6 0/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay
2026-11-19 15:09 ` [PATCH v6 1/2] dt-bindings: gpio: Add Cortina Systems CS7542 GPIO controller Fil Dunsky via B4 Relay
2026-11-19 15:09 ` [PATCH v6 2/2] gpio: Add Cortina Systems CS75xx GPIO driver Fil Dunsky via B4 Relay

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox