public inbox for linux-arm-kernel@lists.infradead.org
 help / color / mirror / Atom feed
From: "Kumar, Udit" <u-kumar1@ti.com>
To: Nishanth Menon <nm@ti.com>
Cc: <linux-arm-kernel@lists.infradead.org>, <afd@ti.com>, <bb@ti.com>,
	<vaishnav.a@ti.com>, <j-choudhary@ti.com>,
	<devicetree@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<vigneshr@ti.com>, <kristo@kernel.org>, <robh+dt@kernel.org>,
	<krzysztof.kozlowski+dt@linaro.org>, J Keerthi <j-keerthy@ti.com>
Subject: Re: [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin
Date: Sat, 15 Apr 2023 09:40:10 +0530	[thread overview]
Message-ID: <20bbb3f0-ac79-9d98-9c99-7062581b163f@ti.com> (raw)
In-Reply-To: <20230414182638.watc555ihi2hgkuv@slinging>

Hi Nishanth

On 4/14/2023 11:56 PM, Nishanth Menon wrote:
> On 23:44-20230414, Udit Kumar wrote:
>> Fixes: 9ae21ac445e9 ("arm64: dts: ti: k3-j7200: Fix wakeup pinmux range")
> In the wrong place.


will address in v2


>> wkup_pmx splits into multiple regions. Like
>>
>>      wkup_pmx0 -> 13 pins (WKUP_PADCONFIG 0 - 12)
>>      wkup_pmx1 -> 2 pins (WKUP_PADCONFIG 14 - 15)
>>      wkup_pmx2 -> 59 pins (WKUP_PADCONFIG 26 - 84)
>>      wkup_pmx3 -> 8 pins (WKUP_PADCONFIG 93 - 100)
>>
>> With this split, pin offset needs to be adjusted to
>> match with new pmx for all pins above wkup_pmx0.
>>
>> Example a pin under wkup_pmx1 should start from 0 instead of
>> old offset(0x38 WKUP_PADCONFIG 14 offset)
>>
>> J7200 Datasheet (Table 6-106, Section 6.4 Pin Multiplexing) :
>>              https://www.ti.com/lit/ds/symlink/dra821u.pdf
> Drop the preceding whitespace.

ok

>> Signed-off-by: J Keerthi <j-keerthy@ti.com>
> Spell check name please, I think he usually goes with:
>
> Signed-off-by: Keerthy <j-keerthy@ti.com>
>
> If this patch is from Keerthy, the patch should have a "From:"

ok.

git apply on original patch didn't worked , so i applied and committed.

will fix in patch itself before posting, Keerthi as author


>> Signed-off-by: Udit Kumar <u-kumar1@ti.com>
>> ---
>>   .../dts/ti/k3-j7200-common-proc-board.dts     | 28 +++++++++----------
>>   1 file changed, 14 insertions(+), 14 deletions(-)
>>
>> diff --git a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> index 0d39d6b8cc0c..63633e4f6c59 100644
>> --- a/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> +++ b/arch/arm64/boot/dts/ti/k3-j7200-common-proc-board.dts
>> @@ -83,25 +83,25 @@ vdd_sd_dv: gpio-regulator-TLV71033 {
>>   &wkup_pmx2 {
>>   	mcu_cpsw_pins_default: mcu-cpsw-pins-default {
>>   		pinctrl-single,pins = <
>> -			J721E_WKUP_IOPAD(0x0068, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
>> -			J721E_WKUP_IOPAD(0x006c, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
>> -			J721E_WKUP_IOPAD(0x0070, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
>> -			J721E_WKUP_IOPAD(0x0074, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
>> -			J721E_WKUP_IOPAD(0x0078, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
>> -			J721E_WKUP_IOPAD(0x007c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
>> -			J721E_WKUP_IOPAD(0x0088, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
>> -			J721E_WKUP_IOPAD(0x008c, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
>> -			J721E_WKUP_IOPAD(0x0090, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
>> -			J721E_WKUP_IOPAD(0x0094, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
>> -			J721E_WKUP_IOPAD(0x0080, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
>> -			J721E_WKUP_IOPAD(0x0084, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
>> +			J721E_WKUP_IOPAD(0x0000, PIN_OUTPUT, 0) /* MCU_RGMII1_TX_CTL */
>> +			J721E_WKUP_IOPAD(0x0004, PIN_INPUT, 0) /* MCU_RGMII1_RX_CTL */
>> +			J721E_WKUP_IOPAD(0x0008, PIN_OUTPUT, 0) /* MCU_RGMII1_TD3 */
>> +			J721E_WKUP_IOPAD(0x000c, PIN_OUTPUT, 0) /* MCU_RGMII1_TD2 */
>> +			J721E_WKUP_IOPAD(0x0010, PIN_OUTPUT, 0) /* MCU_RGMII1_TD1 */
>> +			J721E_WKUP_IOPAD(0x0014, PIN_OUTPUT, 0) /* MCU_RGMII1_TD0 */
>> +			J721E_WKUP_IOPAD(0x0020, PIN_INPUT, 0) /* MCU_RGMII1_RD3 */
>> +			J721E_WKUP_IOPAD(0x0024, PIN_INPUT, 0) /* MCU_RGMII1_RD2 */
>> +			J721E_WKUP_IOPAD(0x0028, PIN_INPUT, 0) /* MCU_RGMII1_RD1 */
>> +			J721E_WKUP_IOPAD(0x002c, PIN_INPUT, 0) /* MCU_RGMII1_RD0 */
>> +			J721E_WKUP_IOPAD(0x0018, PIN_OUTPUT, 0) /* MCU_RGMII1_TXC */
>> +			J721E_WKUP_IOPAD(0x001c, PIN_INPUT, 0) /* MCU_RGMII1_RXC */
> nice catch.
>
>>   		>;
>>   	};
>>   
>>   	mcu_mdio_pins_default: mcu-mdio1-pins-default {
>>   		pinctrl-single,pins = <
>> -			J721E_WKUP_IOPAD(0x009c, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
>> -			J721E_WKUP_IOPAD(0x0098, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>> +			J721E_WKUP_IOPAD(0x0034, PIN_OUTPUT, 0) /* (L1) MCU_MDIO0_MDC */
>> +			J721E_WKUP_IOPAD(0x0030, PIN_INPUT, 0) /* (L4) MCU_MDIO0_MDIO */
>>   		>;
>>   	};
>>   };
>> -- 
>> 2.34.1
>>

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

  reply	other threads:[~2023-04-15  4:11 UTC|newest]

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-04-14 18:14 [PATCH 0/2] arm64: dts: ti: k3-j7200-common-proc-board fixes Udit Kumar
2023-04-14 18:14 ` [PATCH 1/2] arm64: dts: ti: k3-j7200: Fix physical address of pin Udit Kumar
2023-04-14 18:26   ` Nishanth Menon
2023-04-15  4:10     ` Kumar, Udit [this message]
2023-04-15 12:47       ` Nishanth Menon
2023-04-14 18:14 ` [PATCH 2/2] arm64: dts: ti: k3-j7200-common-proc-board: Enable I2C Udit Kumar
2023-04-14 18:24   ` Nishanth Menon
2023-04-15  4:06     ` Kumar, Udit
2023-04-15 12:47       ` Nishanth Menon

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20bbb3f0-ac79-9d98-9c99-7062581b163f@ti.com \
    --to=u-kumar1@ti.com \
    --cc=afd@ti.com \
    --cc=bb@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=j-choudhary@ti.com \
    --cc=j-keerthy@ti.com \
    --cc=kristo@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=vaishnav.a@ti.com \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox