[PATCH 0/4] Add DP AltMode VDO definitions for DT usage

[PATCH 0/4] Add DP AltMode VDO definitions for DT usage

[Sebastian Reichel]

Make DP AltMode devicetree entries more readable by adding a few
defines. This hopefully helps to correctly describe the supported
DP AltMode when boards are being upstreamed. Apparently right now
all upstream boards with DP AltMode *should* have set their VDO to
0x00001c46, which means that they can output DP1.4 with C, D or E
pin mapping on a receptacle that also has functional USB 2.

The patch series is based on current master.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
Sebastian Reichel (4):
      dt-bindings: connector: Add DP AltMode VDO definitions
      arm64: dts: rockchip: Use DP AltMode defines
      arm64: dts: mediatek: Use DP AltMode defines
      arm64: dts: qcom: Use DP AltMode defines

 .../boot/dts/mediatek/mt8390-genio-common.dtsi     |  8 ++-
 .../boot/dts/mediatek/mt8395-genio-common.dtsi     | 10 +++-
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts           |  8 ++-
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts            |  9 +++-
 .../dts/rockchip/rk3576-anbernic-rg-vita-pro.dts   |  8 ++-
 .../boot/dts/rockchip/rk3576-armsom-cm5-io.dts     |  8 ++-
 .../boot/dts/rockchip/rk3576-armsom-sige5.dts      |  8 ++-
 .../boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi   |  8 ++-
 .../boot/dts/rockchip/rk3588s-indiedroid-nova.dts  |  8 ++-
 include/dt-bindings/usb/pd.h                       | 58 ++++++++++++++++++++++
 10 files changed, 115 insertions(+), 18 deletions(-)
---
base-commit: 0fcb05b72344f40806cbe810de8872f1698bf053
change-id: 20261010-dp-altmode-dt-defines-2aa5a94b76f5

Best regards,
--  
Sebastian Reichel <sebastian.reichel@collabora.com>

[PATCH 1/4] dt-bindings: connector: Add DP AltMode VDO definitions

[Sebastian Reichel]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

The typical USB-C DisplayPort AltMode capabilities for a down facing
port (i.e. sending out video data) looks like this:

altmodes {
	displayport {
		svid = /bits/ 16 <0xff01>;
		vdo = <0x00001c46>;
	};
};

Improve the readability by adding defines for the numbers, so that
the above instead looks like this:

altmodes {
	displayport {
		svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
		vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
			      DP_CAP_UHBR_13_5_UNSUPPORTED,
			      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
			      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
			      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
	};
};

The generated DT binary will stay unchanged.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 include/dt-bindings/usb/pd.h | 58 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 58 insertions(+)

diff --git a/include/dt-bindings/usb/pd.h b/include/dt-bindings/usb/pd.h
index 1e64a1f563f9..6cea6165fc0f 100644
--- a/include/dt-bindings/usb/pd.h
+++ b/include/dt-bindings/usb/pd.h
@@ -483,6 +483,64 @@
 	 | ((vbm) & 0x3) << 15 | (curr) << 14 | ((vbi) & 0x3f) << 7	\
 	 | ((gi) & 0x3f) << 1 | (ct))
 
+/*
+ * Displayport AltMode VDO
+ * -----------------------
+ * <30>    :: DPAM version
+ * <29:28> :: Cable type
+ * <26>    :: UHBR 13.5 support
+ * <23:16> :: UFP Pin assignment
+ * <15:8>  :: DFP Pin assignment
+ * <7>     :: USB
+ * <6>     :: Receptacle
+ * <5:2>   :: Signalling
+ * <1:0>   :: Capabilities
+ */
+#define DP_CAP_UFP_D			1
+#define DP_CAP_DFP_D			2
+#define DP_CAP_DFP_D_AND_UFP_D		3
+
+#define DP_CAP_SIGNALLING_HBR3		1
+#define DP_CAP_SIGNALLING_UHBR10	2
+#define DP_CAP_SIGNALLING_UHBR20	3
+
+#define DP_CAP_PLUG			0
+#define DP_CAP_RECEPTACLE		1
+
+#define DP_CAP_USB2_USED		0
+#define DP_CAP_USB2_UNUSED		1
+
+#define DP_PIN_ASSIGN_A			0x01 /* Not supported after v1.0b */
+#define DP_PIN_ASSIGN_B			0x02 /* Not supported after v1.0b */
+#define DP_PIN_ASSIGN_C			0x04
+#define DP_PIN_ASSIGN_D			0x08
+#define DP_PIN_ASSIGN_E			0x10
+#define DP_PIN_ASSIGN_F			0x20 /* Not supported after v1.0b */
+
+#define DP_PIN_UFP_NONE		0x00
+#define DP_PIN_DFP_C_D_E	(DP_PIN_ASSIGN_C | \
+				DP_PIN_ASSIGN_D | \
+				DP_PIN_ASSIGN_E)
+
+#define DP_CAP_UHBR_13_5_UNSUPPORTED	0
+#define DP_CAP_UHBR_13_5_SUPPORTED	1
+
+#define DP_CAP_CABLE_TYPE_PASSIVE	0
+#define DP_CAP_CABLE_TYPE_RE_TIMER	1
+#define DP_CAP_CABLE_TYPE_RE_DRIVER	2
+#define DP_CAP_CABLE_TYPE_OPTICAL	3
+
+#define DP_CAP_DPAM_V2_0		0
+#define DP_CAP_DPAM_V2_1		1
+
+#define VDO_DP(dpam, cable, uhbr, ufp_pins, dfp_pins, usb, rcpt, sig, caps)	\
+	(((dpam) & 1) << 30 | ((cable) & 3) << 28 | ((uhbr) & 1) << 26		\
+	 | ((ufp_pins) & 0xff) << 16 | ((dfp_pins) & 0xff) << 8			\
+	 | ((usb) & 1) << 7 | ((rcpt) & 1) << 6 | ((sig) & 0xf) << 2		\
+	 | ((caps) & 3))
+
+#define USB_SVID_DP_ALTMODE		0xff01
+
 /*
  * Sink Load Characteristics
  * -------------------------

-- 
2.53.0

Re: [PATCH 1/4] dt-bindings: connector: Add DP AltMode VDO definitions

[Dmitry Baryshkov]

On Wed, Oct 14, 2026 at 11:31:49PM +0200, Sebastian Reichel wrote:
> From: Sebastian Reichel <sebastian.reichel@collabora.com>
> 
> The typical USB-C DisplayPort AltMode capabilities for a down facing
> port (i.e. sending out video data) looks like this:
> 
> altmodes {
> 	displayport {
> 		svid = /bits/ 16 <0xff01>;
> 		vdo = <0x00001c46>;
> 	};
> };
> 
> Improve the readability by adding defines for the numbers, so that
> the above instead looks like this:
> 
> altmodes {
> 	displayport {
> 		svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
> 		vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
> 			      DP_CAP_UHBR_13_5_UNSUPPORTED,
> 			      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
> 			      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
> 			      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
> 	};
> };
> 
> The generated DT binary will stay unchanged.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  include/dt-bindings/usb/pd.h | 58 ++++++++++++++++++++++++++++++++++++++++++++
>  1 file changed, 58 insertions(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

[PATCH 2/4] arm64: dts: rockchip: Use DP AltMode defines

[Sebastian Reichel]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

Use the new USB-C DP AltMode defines for the SVID and the capabilities
VDO to make the DTs more readable. This also fixes up announcing
0xffffffff, which is simply wrong as that allows using the port in
upfacing mode (i.e. the board receiving DisplayPort data, bandwidth
above HBR3 or pin configurations not handled by USBDP.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/rockchip/rk3576-anbernic-rg-vita-pro.dts | 8 ++++++--
 arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts        | 8 ++++++--
 arch/arm64/boot/dts/rockchip/rk3576-armsom-sige5.dts         | 8 ++++++--
 arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi      | 8 ++++++--
 arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts     | 8 ++++++--
 5 files changed, 30 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3576-anbernic-rg-vita-pro.dts b/arch/arm64/boot/dts/rockchip/rk3576-anbernic-rg-vita-pro.dts
index 358dea43f9b6..621f786147d5 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-anbernic-rg-vita-pro.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-anbernic-rg-vita-pro.dts
@@ -911,8 +911,12 @@ connector {
 
 			altmodes {
 				displayport {
-					svid = /bits/ 16 <0xff01>;
-					vdo = <0xffffffff>;
+					svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+						      DP_CAP_UHBR_13_5_UNSUPPORTED,
+						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 				};
 			};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
index ebb231271e45..d154e9037ed0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts
@@ -204,8 +204,12 @@ PDO_FIXED(9000, 3000, PDO_FIXED_USB_COMM)
 
 			altmodes {
 				displayport {
-					svid = /bits/ 16 <0xff01>;
-					vdo = <0xffffffff>;
+					svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+						      DP_CAP_UHBR_13_5_UNSUPPORTED,
+						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 				};
 			};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3576-armsom-sige5.dts b/arch/arm64/boot/dts/rockchip/rk3576-armsom-sige5.dts
index 4ac4465e39a5..e457fb37f3b3 100644
--- a/arch/arm64/boot/dts/rockchip/rk3576-armsom-sige5.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3576-armsom-sige5.dts
@@ -711,8 +711,12 @@ connector {
 
 			altmodes {
 				displayport {
-					svid = /bits/ 16 <0xff01>;
-					vdo = <0xffffffff>;
+					svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+						      DP_CAP_UHBR_13_5_UNSUPPORTED,
+						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 				};
 			};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi
index 13aaf63ad093..163ad7eef4fd 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi
@@ -346,8 +346,12 @@ usb_con: connector {
 
 			altmodes {
 				displayport {
-					svid = /bits/ 16 <0xff01>;
-					vdo = <0xffffffff>;
+					svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+						      DP_CAP_UHBR_13_5_UNSUPPORTED,
+						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 				};
 			};
 
diff --git a/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts b/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts
index ed36c27c2320..8f6f32ee2074 100644
--- a/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts
@@ -392,8 +392,12 @@ usb_con: connector {
 
 			altmodes {
 				displayport {
-					svid = /bits/ 16 <0xff01>;
-					vdo = <0xffffffff>;
+					svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+						      DP_CAP_UHBR_13_5_UNSUPPORTED,
+						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 				};
 			};
 

-- 
2.53.0

Re: [PATCH 2/4] arm64: dts: rockchip: Use DP AltMode defines

[Dmitry Baryshkov]

On Wed, Oct 14, 2026 at 11:31:50PM +0200, Sebastian Reichel wrote:
> From: Sebastian Reichel <sebastian.reichel@collabora.com>
> 
> Use the new USB-C DP AltMode defines for the SVID and the capabilities
> VDO to make the DTs more readable. This also fixes up announcing
> 0xffffffff, which is simply wrong as that allows using the port in
> upfacing mode (i.e. the board receiving DisplayPort data, bandwidth
> above HBR3 or pin configurations not handled by USBDP.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  arch/arm64/boot/dts/rockchip/rk3576-anbernic-rg-vita-pro.dts | 8 ++++++--
>  arch/arm64/boot/dts/rockchip/rk3576-armsom-cm5-io.dts        | 8 ++++++--
>  arch/arm64/boot/dts/rockchip/rk3576-armsom-sige5.dts         | 8 ++++++--
>  arch/arm64/boot/dts/rockchip/rk3588-rock-5b-5bp-5t.dtsi      | 8 ++++++--
>  arch/arm64/boot/dts/rockchip/rk3588s-indiedroid-nova.dts     | 8 ++++++--
>  5 files changed, 30 insertions(+), 10 deletions(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

[PATCH 3/4] arm64: dts: mediatek: Use DP AltMode defines

[Sebastian Reichel]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

Use the new USB-C DP AltMode defines for the SVID and the capabilities
VDO to make the DTs more readable. This also fixes up mt8390 Genio
platform incorrectly announcing UFP_D (upwards facing) support. This
feature is unfortunately not supported by the SoC.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi |  8 ++++++--
 arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi | 10 ++++++++--
 2 files changed, 14 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi b/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
index 669eaec662f3..02f8b33d64ac 100644
--- a/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
@@ -527,8 +527,12 @@ PDO_FIXED_DUAL_ROLE |
 
 			altmodes {
 				displayport {
-					svid = /bits/ 16 <0xff01>;
-					vdo = <0x001c1c47>;
+					svid = /bits/ 16 <USB_DISPLAYPORT_SVID>;
+					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+						      DP_CAP_UHBR_13_5_UNSUPPORTED,
+						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 				};
 			};
 
diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi b/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi
index aef908df530e..3f7d57dfcf93 100644
--- a/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi
@@ -597,8 +597,14 @@ PDO_FIXED_DUAL_ROLE |
 
 				altmodes {
 					displayport {
-						svid = /bits/ 16 <0xff01>;
-						vdo = <0x00001c46>;
+						svid = /bits/ 16 <USB_DISPLAYPORT_SVID>;
+						vdo = <VDO_DP(DP_CAP_DPAM_V2_0,
+							      DP_CAP_CABLE_TYPE_PASSIVE,
+							      DP_CAP_UHBR_13_5_UNSUPPORTED,
+							      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+							      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+							      DP_CAP_SIGNALLING_HBR3,
+							      DP_CAP_DFP_D)>;
 					};
 				};
 

-- 
2.53.0

Re: [PATCH 3/4] arm64: dts: mediatek: Use DP AltMode defines

[Dmitry Baryshkov]

On Wed, Oct 14, 2026 at 11:31:51PM +0200, Sebastian Reichel wrote:
> From: Sebastian Reichel <sebastian.reichel@collabora.com>
> 
> Use the new USB-C DP AltMode defines for the SVID and the capabilities
> VDO to make the DTs more readable. This also fixes up mt8390 Genio
> platform incorrectly announcing UFP_D (upwards facing) support. This
> feature is unfortunately not supported by the SoC.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi |  8 ++++++--
>  arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi | 10 ++++++++--
>  2 files changed, 14 insertions(+), 4 deletions(-)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>


-- 
With best wishes
Dmitry

Re: [PATCH 3/4] arm64: dts: mediatek: Use DP AltMode defines

[Dmitry Baryshkov]

On Wed, Oct 14, 2026 at 11:31:51PM +0200, Sebastian Reichel wrote:
> From: Sebastian Reichel <sebastian.reichel@collabora.com>
> 
> Use the new USB-C DP AltMode defines for the SVID and the capabilities
> VDO to make the DTs more readable. This also fixes up mt8390 Genio
> platform incorrectly announcing UFP_D (upwards facing) support. This
> feature is unfortunately not supported by the SoC.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---
>  arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi |  8 ++++++--
>  arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi | 10 ++++++++--
>  2 files changed, 14 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi b/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
> index 669eaec662f3..02f8b33d64ac 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8390-genio-common.dtsi
> @@ -527,8 +527,12 @@ PDO_FIXED_DUAL_ROLE |
>  
>  			altmodes {
>  				displayport {
> -					svid = /bits/ 16 <0xff01>;
> -					vdo = <0x001c1c47>;
> +					svid = /bits/ 16 <USB_DISPLAYPORT_SVID>;

USB_SVID_DP_ALTMODE

> +					vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
> +						      DP_CAP_UHBR_13_5_UNSUPPORTED,
> +						      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
> +						      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
> +						      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
>  				};
>  			};
>  
> diff --git a/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi b/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi
> index aef908df530e..3f7d57dfcf93 100644
> --- a/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi
> +++ b/arch/arm64/boot/dts/mediatek/mt8395-genio-common.dtsi
> @@ -597,8 +597,14 @@ PDO_FIXED_DUAL_ROLE |
>  
>  				altmodes {
>  					displayport {
> -						svid = /bits/ 16 <0xff01>;
> -						vdo = <0x00001c46>;
> +						svid = /bits/ 16 <USB_DISPLAYPORT_SVID>;

USB_SVID_DP_ALTMODE

> +						vdo = <VDO_DP(DP_CAP_DPAM_V2_0,
> +							      DP_CAP_CABLE_TYPE_PASSIVE,
> +							      DP_CAP_UHBR_13_5_UNSUPPORTED,
> +							      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
> +							      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
> +							      DP_CAP_SIGNALLING_HBR3,
> +							      DP_CAP_DFP_D)>;
>  					};
>  				};
>  
> 
> -- 
> 2.53.0
> 

-- 
With best wishes
Dmitry

[PATCH 4/4] arm64: dts: qcom: Use DP AltMode defines

[Sebastian Reichel]

From: Sebastian Reichel <sebastian.reichel@collabora.com>

Use the new USB-C DP AltMode defines for the SVID and the capabilities
VDO to make the DTs more readable.

Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
---
 arch/arm64/boot/dts/qcom/qrb5165-rb5.dts | 8 ++++++--
 arch/arm64/boot/dts/qcom/sm8150-hdk.dts  | 9 +++++++--
 2 files changed, 13 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
index d6af679abe1a..d21b94e872ce 100644
--- a/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
+++ b/arch/arm64/boot/dts/qcom/qrb5165-rb5.dts
@@ -1508,8 +1508,12 @@ PDO_FIXED_USB_COMM |
 
 		altmodes {
 			displayport {
-				svid = /bits/ 16 <0xff01>;
-				vdo = <0x00001c46>;
+				svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+				vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+					      DP_CAP_UHBR_13_5_UNSUPPORTED,
+					      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+					      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+					      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
 			};
 		};
 
diff --git a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
index cdced5c848d3..3d83dd305954 100644
--- a/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8150-hdk.dts
@@ -581,8 +581,13 @@ PDO_FIXED_USB_COMM |
 
 		altmodes {
 			displayport {
-				svid = /bits/ 16 <0xff01>;
-				vdo = <0x00001c46>;
+				svid = /bits/ 16 <USB_SVID_DP_ALTMODE>;
+				vdo = <VDO_DP(DP_CAP_DPAM_V2_0, DP_CAP_CABLE_TYPE_PASSIVE,
+					      DP_CAP_UHBR_13_5_UNSUPPORTED,
+					      DP_PIN_UFP_NONE, DP_PIN_DFP_C_D_E,
+					      DP_CAP_USB2_USED, DP_CAP_RECEPTACLE,
+					      DP_CAP_SIGNALLING_HBR3, DP_CAP_DFP_D)>;
+
 			};
 		};
 

-- 
2.53.0

Re: [PATCH 4/4] arm64: dts: qcom: Use DP AltMode defines

[Konrad Dybcio]

On 10/14/26 11:31 PM, Sebastian Reichel wrote:
> From: Sebastian Reichel <sebastian.reichel@collabora.com>
> 
> Use the new USB-C DP AltMode defines for the SVID and the capabilities
> VDO to make the DTs more readable.
> 
> Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad