Linux-ARM-Kernel Archive on lore.kernel.org
 help / color / mirror / Atom feed
* [PATCH 0/3] mailbox: Add Marvell MHU driver
@ 2026-11-19 15:29 Paul Cercueil
  2026-11-19 15:29 ` [PATCH 1/3] dt-bindings: mailbox: add Marvell MHU Paul Cercueil
                   ` (3 more replies)
  0 siblings, 4 replies; 5+ messages in thread
From: Paul Cercueil @ 2026-11-19 15:29 UTC (permalink / raw)
  To: Jassi Brar
  Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sudeep Holla,
	Cristian Marussi, Thomas Petazzoni, Sunil Kovvuri Goutham,
	linux-kernel, devicetree, arm-scmi, linux-arm-kernel,
	Paul Cercueil

Hi Jassi,

This patchset adds support for the mailbox found in the OcteonTX and
OcteonTX2 based SoCs, which is used for SCMI communication.

This is technically a v5, where the v4 was sent in 2023 [1].
Given that years have passed, and that the original authors left Marvell
AFAIK, I figured out it was just better to restart at v1.

The last patch applies to the SCMI driver, it does not have a direct
dependency on the other two and can go through the ARM tree, if you or
the ARM-SCMI maintainers prefer so.

Cheers,
-Paul

[1]: https://lore.kernel.org/all/4397b39c-084b-954b-956a-5168a3c8958c@linaro.org/T/

George Cherian (3):
  dt-bindings: mailbox: add Marvell MHU
  mailbox: marvell-mhu: add Marvell MHU driver
  scmi: driver: Increase timeout for rx response

 .../bindings/mailbox/marvell,mhu.yaml         |  60 ++++
 MAINTAINERS                                   |   7 +
 .../firmware/arm_scmi/transports/mailbox.c    |   2 +-
 drivers/mailbox/Kconfig                       |  11 +
 drivers/mailbox/Makefile                      |   2 +
 drivers/mailbox/marvell_mhu.c                 | 267 ++++++++++++++++++
 6 files changed, 348 insertions(+), 1 deletion(-)
 create mode 100644 Documentation/devicetree/bindings/mailbox/marvell,mhu.yaml
 create mode 100644 drivers/mailbox/marvell_mhu.c

-- 
2.47.3



^ permalink raw reply	[flat|nested] 5+ messages in thread

* [PATCH 1/3] dt-bindings: mailbox: add Marvell MHU
  2026-11-19 15:29 [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
@ 2026-11-19 15:29 ` Paul Cercueil
  2026-11-19 15:29 ` [PATCH 2/3] mailbox: marvell-mhu: add Marvell MHU driver Paul Cercueil
                   ` (2 subsequent siblings)
  3 siblings, 0 replies; 5+ messages in thread
From: Paul Cercueil @ 2026-11-19 15:29 UTC (permalink / raw)
  To: Jassi Brar
  Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sudeep Holla,
	Cristian Marussi, Thomas Petazzoni, Sunil Kovvuri Goutham,
	linux-kernel, devicetree, arm-scmi, linux-arm-kernel,
	George Cherian, Sujeet Baranwal, Paul Cercueil

From: George Cherian <gcherian@marvell.com>

Marvell Message Handling Unit is a mailbox controller present in
Marvell OcteonTx and OcteonTX2 SoC family.

Signed-off-by: George Cherian <gcherian@marvell.com>
Co-developed-by: Sujeet Baranwal <sbaranwal@marvell.com>
Signed-off-by: Sujeet Baranwal <sbaranwal@marvell.com>
Signed-off-by: Paul Cercueil <paul.cercueil@bootlin.com>
---
 .../bindings/mailbox/marvell,mhu.yaml         | 60 +++++++++++++++++++
 MAINTAINERS                                   |  6 ++
 2 files changed, 66 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mailbox/marvell,mhu.yaml

diff --git a/Documentation/devicetree/bindings/mailbox/marvell,mhu.yaml b/Documentation/devicetree/bindings/mailbox/marvell,mhu.yaml
new file mode 100644
index 000000000000..228607165f85
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/marvell,mhu.yaml
@@ -0,0 +1,60 @@
+# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/mailbox/marvell,mhu.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Marvell Message Handling Unit
+
+maintainers:
+  - Sujeet Baranwal <sbaranwal@marvell.com>
+  - George Cherian <gcherian@marvell.com>
+
+description:
+  The Control-Processors Cluster (CPC) provides Arm-platform specification
+  entities for managing the system. One of the CPC processors is the System
+  Control Processor (SCP). The SCP is responsible, among others, for booting
+  the chip, clock and power initialization, controlling power consumption
+  through DVFS, monitoring temperature sensors and controlling AVS. The SCP,
+  as each XCP, contains mailboxes for software-to-software communications.
+  Mailbox writes cause an interrupt to the local XCP core or to the AP.
+  This driver exposes AP-SCP Message Handling Unit to the system, providing
+  the mailbox communication mechanism to the system, with the intention
+  of plugging into the SCMI framework. It is designed to work with Marvell
+  OcteonTX and OcteonTX2-based platforms.
+  The mailbox has no other usage than SCMI communication. In case of
+  configurations running without SCMI support it should be disabled.
+
+properties:
+  compatible:
+    enum:
+      - marvell,octeontx-mhu
+      - marvell,octeontx2-mhu
+      - marvell,cn10-mhu
+
+  reg:
+    maxItems: 1
+
+  "#mbox-cells":
+    description: Index of the channel
+    const: 1
+
+required:
+  - compatible
+  - reg
+  - "#mbox-cells"
+
+additionalProperties: false
+
+examples:
+  - |
+    ecam {
+        #address-cells = <3>;
+        #size-cells = <2>;
+            mailbox: mailbox@1c,0 {
+                compatible = "marvell,octeontx2-mhu";
+                reg = <0xe000 0x0 0x0 0 0>;
+                #mbox-cells = <1>;
+            };
+    };
+...
diff --git a/MAINTAINERS b/MAINTAINERS
index 65e8a4b5c90b..b592a62a5c56 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15959,6 +15959,12 @@ R:	Vamsi Attunuru <vattunuru@marvell.com>
 S:	Supported
 F:	drivers/pci/hotplug/octep_hp.c
 
+MARVELL MHU MAILBOX DRIVER
+M:	Sujeet Baranwal <sbaranwal@marvell.com>
+M:	George Cherian <gcherian@marvell.com>
+S:	Maintained
+F:	Documentation/devicetree/bindings/mailbox/marvell,mhu.yml
+
 MATROX FRAMEBUFFER DRIVER
 L:	linux-fbdev@vger.kernel.org
 S:	Orphan
-- 
2.47.3



^ permalink raw reply related	[flat|nested] 5+ messages in thread

* [PATCH 2/3] mailbox: marvell-mhu: add Marvell MHU driver
  2026-11-19 15:29 [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
  2026-11-19 15:29 ` [PATCH 1/3] dt-bindings: mailbox: add Marvell MHU Paul Cercueil
@ 2026-11-19 15:29 ` Paul Cercueil
  2026-11-19 15:29 ` [PATCH 3/3] scmi: driver: Increase timeout for rx response Paul Cercueil
  2026-11-19 15:54 ` [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
  3 siblings, 0 replies; 5+ messages in thread
From: Paul Cercueil @ 2026-11-19 15:29 UTC (permalink / raw)
  To: Jassi Brar
  Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sudeep Holla,
	Cristian Marussi, Thomas Petazzoni, Sunil Kovvuri Goutham,
	linux-kernel, devicetree, arm-scmi, linux-arm-kernel,
	George Cherian, Sujeet Baranwal, Paul Cercueil

From: George Cherian <gcherian@marvell.com>

Add support for Message Handling Units on Marvell OcteonTx and OcteonTx2
platforms. The module uses mailbox controller interface to provide
communication between SCP and AP using SCMI protocol over a single
shared memory communication channel.

Signed-off-by: George Cherian <gcherian@marvell.com>
Co-developed-by: Sujeet Baranwal <sbaranwal@marvell.com>
Signed-off-by: Sujeet Baranwal <sbaranwal@marvell.com>
Signed-off-by: Paul Cercueil <paul.cercueil@bootlin.com>
---
 MAINTAINERS                   |   1 +
 drivers/mailbox/Kconfig       |  11 ++
 drivers/mailbox/Makefile      |   2 +
 drivers/mailbox/marvell_mhu.c | 267 ++++++++++++++++++++++++++++++++++
 4 files changed, 281 insertions(+)
 create mode 100644 drivers/mailbox/marvell_mhu.c

diff --git a/MAINTAINERS b/MAINTAINERS
index b592a62a5c56..63042166c0da 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15964,6 +15964,7 @@ M:	Sujeet Baranwal <sbaranwal@marvell.com>
 M:	George Cherian <gcherian@marvell.com>
 S:	Maintained
 F:	Documentation/devicetree/bindings/mailbox/marvell,mhu.yml
+F:	drivers/mailbox/marvell_mhu.c
 
 MATROX FRAMEBUFFER DRIVER
 L:	linux-fbdev@vger.kernel.org
diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
index ab869769e278..ce3b70749a18 100644
--- a/drivers/mailbox/Kconfig
+++ b/drivers/mailbox/Kconfig
@@ -195,6 +195,17 @@ config MAILBOX_TEST
 	  Test client to help with testing new Controller driver
 	  implementations.
 
+config MARVELL_MHU
+	tristate "Marvell Message Handling Unit"
+	depends on (ARM64 || COMPILE_TEST) && 64BIT
+	depends on OF
+	help
+	  This driver adds support for Marvell MHU controller.
+	  The MHU mailbox is used by SCMI for OcteonTX and OcteonTX2
+	  to control various aspects of platform operation like cpufreq
+	  or sensors. The controller supports single channel to SCP.
+	  Say Y here to build this module. If unsure say N.
+
 config POLARFIRE_SOC_MAILBOX
 	tristate "PolarFire SoC (MPFS) Mailbox"
 	depends on HAS_IOMEM
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index 45dc59bb3e7f..83b26e7bbd27 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -49,6 +49,8 @@ obj-$(CONFIG_BCM_PDC_MBOX)	+= bcm-pdc-mailbox.o
 
 obj-$(CONFIG_BCM_FLEXRM_MBOX)	+= bcm-flexrm-mailbox.o
 
+obj-$(CONFIG_MARVELL_MHU)	+= marvell_mhu.o
+
 obj-$(CONFIG_POLARFIRE_SOC_MAILBOX)	+= mailbox-mpfs.o
 
 obj-$(CONFIG_MCHP_SBI_IPC_MBOX)		+= mailbox-mchp-ipc-sbi.o
diff --git a/drivers/mailbox/marvell_mhu.c b/drivers/mailbox/marvell_mhu.c
new file mode 100644
index 000000000000..a037fe104195
--- /dev/null
+++ b/drivers/mailbox/marvell_mhu.c
@@ -0,0 +1,267 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Marvell Message Handling Unit
+ *
+ * Copyright (c) 2023, 2026 Marvell
+ */
+
+#define DRIVER_NAME	"marvell-mhu"
+
+#define pr_fmt(fmt)	DRIVER_NAME ": " fmt
+
+#include <linux/pci.h>
+#include <linux/acpi.h>
+#include <linux/mailbox_controller.h>
+
+#define BAR0		0
+#define SCP_INDEX	0x0
+#define DEV_AP0		0x2
+#define SCP_TO_AP_INTERRUPT	2
+#define INT_VECS_MIN	0
+#define INT_VECS_MAX	3
+
+#define XCPX_DEVY_XCP_MBOX_LINT_OFFSET	0x000E1C00
+#define XCP_TO_DEV_XCP_MBOX_LINT(xcp_core, device_id)  \
+	(XCPX_DEVY_XCP_MBOX_LINT_OFFSET | \
+	((uint64_t)(xcp_core) << 36) | \
+	((uint64_t)(device_id) << 4))
+
+#define AP0_TO_SCP_MBOX_LINT    XCP_TO_DEV_XCP_MBOX_LINT(SCP_INDEX, DEV_AP0)
+
+/*
+ * Doorbell-Register: XCP(0..1)_DEV(0..7)_XCP_MBOX
+ * Communication data from devices to XCP. When written, sets
+ * XCP(0..1)_DEV(0..7)_XCP_MBOX.
+ * PS: it doesn't matter what is written into this register,
+ * Attempting to writing 'anything' would cause an interrupt
+ * to the target!
+ */
+
+#define XCPX_DEVY_XCP_MBOX_OFFSET	0x000E1000
+#define XCP_TO_DEV_XCP_MBOX(xcp_core, device_id) \
+	(XCPX_DEVY_XCP_MBOX_OFFSET | \
+	((uint64_t)(xcp_core) << 36) | \
+	((uint64_t)(device_id) << 4))
+
+/* AP0-to-SCP doorbell */
+#define AP0_TO_SCP_MBOX         XCP_TO_DEV_XCP_MBOX(SCP_INDEX, DEV_AP0)
+
+/*  Register offset: Enable interrupt from SCP to AP */
+#define XCP0_XCP_DEV0_MBOX_RINT_ENA_W1S	0x000D1C40
+#define XCP0_XCP_DEV1_MBOX_RINT_ENA_W1S	0x000D1C50
+#define XCP0_XCP_DEV2_MBOX_RINT_ENA_W1S	0x000D1C60
+#define XCP0_XCP_DEV3_MBOX_RINT_ENA_W1S	0x000D1C70
+
+/* Rx interrupt from SCP to Non-secure AP (linux kernel) */
+#define XCPX_XCP_DEVY_MBOX_RINT_OFFSET 0x000D1C00
+#define XCPX_XCP_DEVY_MBOX_RINT(xcp_core, device_id) \
+	(XCPX_XCP_DEVY_MBOX_RINT_OFFSET | \
+	((uint64_t)(xcp_core) << 36) | \
+	((uint64_t)(device_id) << 4))
+
+/* The interrupt status register */
+#define SCP_TO_AP0_MBOX_RINT  XCPX_XCP_DEVY_MBOX_RINT(SCP_INDEX, DEV_AP0)
+
+#define XCPX_XCP_DEVY_MBOX_RINT_OFFSET	0x000D1C00
+#define XCPX_XCP_DEVY_MBOX_RINT(xcp_core, device_id) \
+	(XCPX_XCP_DEVY_MBOX_RINT_OFFSET | \
+	((uint64_t)(xcp_core) << 36) | \
+	((uint64_t)(device_id) << 4))
+
+#define SCP_TO_AP0_MBOX_RINT  XCPX_XCP_DEVY_MBOX_RINT(SCP_INDEX, DEV_AP0)
+#define SCP_TO_DEV0 XCPX_XCP_DEVY_MBOX_RINT(0, 0)
+#define SCP_TO_DEV1 XCPX_XCP_DEVY_MBOX_RINT(0, 1)
+#define SCP_TO_DEV2 XCPX_XCP_DEVY_MBOX_RINT(0, 2)
+#define SCP_TO_DEV3 XCPX_XCP_DEVY_MBOX_RINT(0, 3)
+
+struct mrvl_mhu {
+	/* SCP link information */
+	void __iomem *base; /* tx_reg, rx_reg */
+
+	struct mbox_controller ctrl;
+	struct mbox_chan chan;
+};
+
+static irqreturn_t mrvl_mhu_rx_interrupt(int irq, void *p)
+{
+	struct mrvl_mhu *mhu = p;
+	u64 val;
+
+	/* Read interrupt status register */
+	val = readq_relaxed(mhu->base + SCP_TO_AP0_MBOX_RINT);
+	if (val) {
+		/* Clear the interrupt : Write on clear */
+		writeq_relaxed(1ul, mhu->base + SCP_TO_AP0_MBOX_RINT);
+		/* Poke mbox */
+		mbox_chan_received_data(&mhu->chan, (void *)&val);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static int mrvl_mhu_send_data(struct mbox_chan *chan, void *data)
+{
+	const u64 doorbell = 0xff;  /* Arbitrary value, SCP requires a value */
+	struct mrvl_mhu *mhu = chan->con_priv;
+
+	/* signal SCP */
+	iowrite64(doorbell, mhu->base + AP0_TO_SCP_MBOX);
+
+	return 0;
+}
+
+static bool mrvl_mhu_last_tx_done(struct mbox_chan *chan)
+{
+	struct mrvl_mhu *mhu = chan->con_priv;
+	u64 status;
+
+	status = ioread64(mhu->base + XCPX_XCP_DEVY_MBOX_RINT(0, 2));
+
+	return status != 0;
+}
+
+static int mrvl_mhu_startup(struct mbox_chan *chan)
+{
+	struct mrvl_mhu *mhu = chan->con_priv;
+
+	/* Enable interrupts only if there is client for data */
+	writeq_relaxed(1ul, mhu->base + XCP0_XCP_DEV2_MBOX_RINT_ENA_W1S);
+
+	return 0;
+}
+
+/* Define operations related to mbox */
+static const struct mbox_chan_ops mrvl_mhu_chan_ops = {
+	.startup = mrvl_mhu_startup,
+	.send_data = mrvl_mhu_send_data,
+	.last_tx_done = mrvl_mhu_last_tx_done,
+};
+
+static int mrvl_mhu_setup_irq(struct pci_dev *pdev)
+{
+	struct device *dev;
+	struct mrvl_mhu *mhu;
+	int irq, ret, nvec;
+
+	mhu = pci_get_drvdata(pdev);
+	dev = &pdev->dev;
+
+	nvec = pci_alloc_irq_vectors(pdev, INT_VECS_MIN, INT_VECS_MAX, PCI_IRQ_MSIX);
+	if (nvec < 0)
+		return nvec;
+
+	irq = pci_irq_vector(pdev, SCP_TO_AP_INTERRUPT);
+	if (irq < 0) {
+		ret = irq;
+		goto irq_err;
+	}
+
+	ret = devm_request_irq(dev, irq, mrvl_mhu_rx_interrupt,
+			       0, "mvl-mhu", mhu);
+	if (ret)
+		goto irq_err;
+
+	return 0;
+
+irq_err:
+	pci_free_irq_vectors(pdev);
+
+	return ret;
+}
+
+static const struct of_device_id mrvl_mhu_dt_ids[] = {
+	{ .compatible = "marvell,octeontx-mhu" },
+	{ .compatible = "marvell,octeontx2-mhu" },
+	{ .compatible = "marvell,cn10-mhu" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, mrvl_mhu_dt_ids);
+
+#define PCI_DEVICE_ID_CAVIUM_OCTEON_MHU	0xa067
+static const struct pci_device_id mrvl_mhu_ids[] = {
+	{ PCI_VDEVICE(CAVIUM, PCI_DEVICE_ID_CAVIUM_OCTEON_MHU) },
+	{ 0 },
+};
+MODULE_DEVICE_TABLE(pci, mrvl_mhu_ids);
+
+static int mrvl_mhu_probe(struct pci_dev *pdev, const struct pci_device_id *id)
+{
+	struct device *dev = &pdev->dev;
+	struct mrvl_mhu *mhu;
+	int ret;
+
+	/* Only support PCI devices with a corresponding OF node. */
+	if (!dev->of_node)
+		return -ENODEV;
+	if (!of_match_node(mrvl_mhu_dt_ids, dev->of_node))
+		return -EINVAL;
+
+	mhu = devm_kzalloc(dev, sizeof(*mhu), GFP_KERNEL);
+	if (!mhu)
+		return -ENOMEM;
+
+	mhu->chan = (struct mbox_chan) {
+		.con_priv = mhu,
+	};
+
+	mhu->ctrl = (struct mbox_controller){
+		.chans = &mhu->chan,
+		.num_chans = 1,
+		.txdone_poll = true,
+		.txpoll_period = 100,
+		.ops = &mrvl_mhu_chan_ops,
+		.dev = dev,
+	};
+
+	pci_set_drvdata(pdev, mhu);
+	ret = pcim_enable_device(pdev);
+	if (ret)
+		return ret;
+
+	ret = pcim_request_region(pdev, BAR0, DRIVER_NAME);
+	if (ret)
+		return ret;
+
+	mhu->base = pcim_iomap(pdev, BAR0, pci_resource_len(pdev, BAR0));
+	if (!mhu->base)
+		return -EINVAL;
+
+	/* Configure IRQ from SCP to AP */
+	ret = mrvl_mhu_setup_irq(pdev);
+	if (ret)
+		return ret;
+
+	ret = mbox_controller_register(&mhu->ctrl);
+	if (ret) {
+		pci_free_irq_vectors(pdev);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void mrvl_mhu_remove(struct pci_dev *pdev)
+{
+	struct mrvl_mhu *mhu = pci_get_drvdata(pdev);
+
+	mbox_controller_unregister(&mhu->ctrl);
+	pci_free_irq_vectors(pdev);
+}
+
+static struct pci_driver mrvl_mhu_driver = {
+	.name = DRIVER_NAME,
+	.id_table = mrvl_mhu_ids,
+	.probe = mrvl_mhu_probe,
+	.remove = mrvl_mhu_remove,
+	.driver = {
+		.name = DRIVER_NAME,
+		.of_match_table = mrvl_mhu_dt_ids,
+	},
+};
+module_pci_driver(mrvl_mhu_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_DESCRIPTION("Marvell Message Handling Unit");
+MODULE_AUTHOR("Sujeet Baranwal <sbaranwal@marvell.com>");
+MODULE_AUTHOR("George Cherian <gcherian@marvell.com>");
-- 
2.47.3



^ permalink raw reply related	[flat|nested] 5+ messages in thread

* [PATCH 3/3] scmi: driver: Increase timeout for rx response
  2026-11-19 15:29 [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
  2026-11-19 15:29 ` [PATCH 1/3] dt-bindings: mailbox: add Marvell MHU Paul Cercueil
  2026-11-19 15:29 ` [PATCH 2/3] mailbox: marvell-mhu: add Marvell MHU driver Paul Cercueil
@ 2026-11-19 15:29 ` Paul Cercueil
  2026-11-19 15:54 ` [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
  3 siblings, 0 replies; 5+ messages in thread
From: Paul Cercueil @ 2026-11-19 15:29 UTC (permalink / raw)
  To: Jassi Brar
  Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sudeep Holla,
	Cristian Marussi, Thomas Petazzoni, Sunil Kovvuri Goutham,
	linux-kernel, devicetree, arm-scmi, linux-arm-kernel,
	George Cherian, Sujeet Baranwal, Paul Cercueil

From: George Cherian <gcherian@marvell.com>

The timeout is way off on the Marvell CN10K SoC, where the firmware
processor can take more than 200ms to answer.

Signed-off-by: George Cherian <gcherian@marvell.com>
Co-developed-by: Sujeet Baranwal <sbaranwal@marvell.com>
Signed-off-by: Sujeet Baranwal <sbaranwal@marvell.com>
Signed-off-by: Paul Cercueil <paul.cercueil@bootlin.com>
---
 drivers/firmware/arm_scmi/transports/mailbox.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/firmware/arm_scmi/transports/mailbox.c b/drivers/firmware/arm_scmi/transports/mailbox.c
index 308736c3ead9..78c38d2644aa 100644
--- a/drivers/firmware/arm_scmi/transports/mailbox.c
+++ b/drivers/firmware/arm_scmi/transports/mailbox.c
@@ -380,7 +380,7 @@ static const struct scmi_transport_ops scmi_mailbox_ops = {
 
 static struct scmi_desc scmi_mailbox_desc = {
 	.ops = &scmi_mailbox_ops,
-	.max_rx_timeout_ms = 30, /* We may increase this if required */
+	.max_rx_timeout_ms = 500, /* We may increase this if required */
 	.max_msg = 20, /* Limited by MBOX_TX_QUEUE_LEN */
 	.max_msg_size = SCMI_SHMEM_MAX_PAYLOAD_SIZE,
 };
-- 
2.47.3



^ permalink raw reply related	[flat|nested] 5+ messages in thread

* Re: [PATCH 0/3] mailbox: Add Marvell MHU driver
  2026-11-19 15:29 [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
                   ` (2 preceding siblings ...)
  2026-11-19 15:29 ` [PATCH 3/3] scmi: driver: Increase timeout for rx response Paul Cercueil
@ 2026-11-19 15:54 ` Paul Cercueil
  3 siblings, 0 replies; 5+ messages in thread
From: Paul Cercueil @ 2026-11-19 15:54 UTC (permalink / raw)
  To: Jassi Brar
  Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Sudeep Holla,
	Cristian Marussi, Thomas Petazzoni, Sunil Kovvuri Goutham,
	linux-kernel, devicetree, arm-scmi, linux-arm-kernel

FYI Sashiko found issues in all patches. I'll send a v2 tomorrow or next week.

Cheers,
-Paul

Le jeudi 19 novembre 2026 à 16:29 +0100, Paul Cercueil a écrit :
> Hi Jassi,
> 
> This patchset adds support for the mailbox found in the OcteonTX and
> OcteonTX2 based SoCs, which is used for SCMI communication.
> 
> This is technically a v5, where the v4 was sent in 2023 [1].
> Given that years have passed, and that the original authors left Marvell
> AFAIK, I figured out it was just better to restart at v1.
> 
> The last patch applies to the SCMI driver, it does not have a direct
> dependency on the other two and can go through the ARM tree, if you or
> the ARM-SCMI maintainers prefer so.
> 
> Cheers,
> -Paul
> 
> [1]:
> https://lore.kernel.org/all/4397b39c-084b-954b-956a-5168a3c8958c@linaro.org/T/
> 
> George Cherian (3):
>   dt-bindings: mailbox: add Marvell MHU
>   mailbox: marvell-mhu: add Marvell MHU driver
>   scmi: driver: Increase timeout for rx response
> 
>  .../bindings/mailbox/marvell,mhu.yaml         |  60 ++++
>  MAINTAINERS                                   |   7 +
>  .../firmware/arm_scmi/transports/mailbox.c    |   2 +-
>  drivers/mailbox/Kconfig                       |  11 +
>  drivers/mailbox/Makefile                      |   2 +
>  drivers/mailbox/marvell_mhu.c                 | 267 ++++++++++++++++++
>  6 files changed, 348 insertions(+), 1 deletion(-)
>  create mode 100644 Documentation/devicetree/bindings/mailbox/marvell,mhu.yaml
>  create mode 100644 drivers/mailbox/marvell_mhu.c


^ permalink raw reply	[flat|nested] 5+ messages in thread

end of thread, other threads:[~2026-11-19 15:55 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2026-11-19 15:29 [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil
2026-11-19 15:29 ` [PATCH 1/3] dt-bindings: mailbox: add Marvell MHU Paul Cercueil
2026-11-19 15:29 ` [PATCH 2/3] mailbox: marvell-mhu: add Marvell MHU driver Paul Cercueil
2026-11-19 15:29 ` [PATCH 3/3] scmi: driver: Increase timeout for rx response Paul Cercueil
2026-11-19 15:54 ` [PATCH 0/3] mailbox: Add Marvell MHU driver Paul Cercueil

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox