[PATCH 0/2] pinctrl: mediatek: Add MT6895 support

[PATCH 0/2] pinctrl: mediatek: Add MT6895 support

[Alexander Letuchiy]

This series adds the pin controller of the MediaTek Dimensity 8000/8100
(MT6895) SoC: the binding and a driver on top of the common Paris code.

The pinmux macro header and the pio node will be sent with the next
version of the MT6895 / Xiaomi Poco X4 GT initial support series.

The tables come from the MediaTek driver in the Xiaomi kernel source
release [1]. They were checked field by field against that driver and
against register dumps from the device running the vendor kernel.

Tested on a Xiaomi Poco X4 GT (xaga) on top of next-20261102: pinmux,
pin configuration, GPIO and EINT.

[1] https://github.com/MiCode/Xiaomi_Kernel_OpenSource/tree/56ec519f6
    (branch xaga-s-oss)

Assisted-by: Claude:claude-opus-5-5
---
Alexander Letuchiy (2):
      dt-bindings: pinctrl: mediatek: Document MT6895 pin controller
      pinctrl: mediatek: Add support for MT6895 pinctrl

 .../bindings/pinctrl/mediatek,mt6895-pinctrl.yaml  |  228 ++
 drivers/pinctrl/mediatek/Kconfig                   |   10 +
 drivers/pinctrl/mediatek/Makefile                  |    1 +
 drivers/pinctrl/mediatek/pinctrl-mt6895.c          | 1617 ++++++++++++
 drivers/pinctrl/mediatek/pinctrl-mtk-mt6895.h      | 2717 ++++++++++++++++++++
 5 files changed, 4573 insertions(+)
---
base-commit: 2637bdec0535a2044cd830eba9a79363651d9043
change-id: 20261108-pinctrl-mt6895-84822207f4ac

Best regards,
--  
Alexander Letuchiy <asalde.le1@gmail.com>

[PATCH 1/2] dt-bindings: pinctrl: mediatek: Document MT6895 pin controller

[Alexander Letuchiy]

Add device tree bindings for the pin controller found in the MediaTek
Dimensity 8000/8100 (MT6895) SoC.

The controller has 227 GPIOs spread over a GPIO base and 13 IOCFG
blocks, and an EINT controller made of five blocks (W, E, S, N, C).

Pins with PUPD/R1/R0 or RSEL pull-ups take the raw MTK_PUPD_SET_R1R0_*
and MTK_PULL_SET_RSEL_* values in bias-pull-up and bias-pull-down.
There is no public table of the RSEL resistances for this SoC, so the
binding does not offer the ohm-based values used on MT8188 and MT8195.

Signed-off-by: Alexander Letuchiy <asalde.le1@gmail.com>
---
 .../bindings/pinctrl/mediatek,mt6895-pinctrl.yaml  | 228 +++++++++++++++++++++
 1 file changed, 228 insertions(+)

diff --git a/Documentation/devicetree/bindings/pinctrl/mediatek,mt6895-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6895-pinctrl.yaml
new file mode 100644
index 000000000000..e3ecfffc084e
--- /dev/null
+++ b/Documentation/devicetree/bindings/pinctrl/mediatek,mt6895-pinctrl.yaml
@@ -0,0 +1,228 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pinctrl/mediatek,mt6895-pinctrl.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT6895 Pin Controller
+
+maintainers:
+  - Alexander Letuchiy <asalde.le1@gmail.com>
+
+description:
+  The MediaTek MT6895 Pin controller is used to control SoC pins.
+
+properties:
+  compatible:
+    const: mediatek,mt6895-pinctrl
+
+  reg:
+    items:
+      - description: pin controller base
+      - description: rm group IO
+      - description: rt group IO
+      - description: rmm group IO
+      - description: bl group IO
+      - description: bm group IO
+      - description: br group IO
+      - description: brr group IO
+      - description: lb group IO
+      - description: lm group IO
+      - description: rtt group IO
+      - description: tr group IO
+      - description: tl group IO
+      - description: lt group IO
+      - description: EINT controller W block
+      - description: EINT controller E block
+      - description: EINT controller S block
+      - description: EINT controller N block
+      - description: EINT controller C block
+
+  reg-names:
+    items:
+      - const: base
+      - const: rm
+      - const: rt
+      - const: rmm
+      - const: bl
+      - const: bm
+      - const: br
+      - const: brr
+      - const: lb
+      - const: lm
+      - const: rtt
+      - const: tr
+      - const: tl
+      - const: lt
+      - const: eint-w
+      - const: eint-e
+      - const: eint-s
+      - const: eint-n
+      - const: eint-c
+
+  gpio-controller: true
+
+  '#gpio-cells':
+    description:
+      Number of cells in GPIO specifier. Since the generic GPIO binding is used,
+      the amount of cells must be specified as 2. See the below mentioned gpio
+      binding representation for description of particular cells.
+    const: 2
+
+  gpio-ranges:
+    maxItems: 1
+
+  gpio-line-names:
+    maxItems: 247
+
+  interrupts:
+    description: EINT controller interrupt
+    maxItems: 1
+
+  interrupt-controller: true
+
+  '#interrupt-cells':
+    const: 2
+
+# PIN CONFIGURATION NODES
+patternProperties:
+  '-pins$':
+    type: object
+    additionalProperties: false
+
+    patternProperties:
+      '^pins':
+        type: object
+        allOf:
+          - $ref: /schemas/pinctrl/pincfg-node.yaml
+          - $ref: /schemas/pinctrl/pinmux-node.yaml
+        description:
+          A pinctrl node should contain at least one subnodes representing the
+          pinctrl groups available on the machine. Each subnode will list the
+          pins it needs, and how they should be configured, with regard to muxer
+          configuration, pullups, drive strength, input enable/disable and input
+          schmitt.
+
+        properties:
+          pinmux:
+            description:
+              Integer array, represents gpio pin number and mux setting.
+              Supported pin number and mux are defined as macros in
+              arch/arm64/boot/dts/mediatek/mt6895-pinfunc.h for this SoC.
+
+          drive-strength:
+            enum: [2, 4, 6, 8, 10, 12, 14, 16]
+
+          drive-strength-microamp:
+            enum: [125, 250, 500, 1000]
+
+          bias-pull-down:
+            oneOf:
+              - type: boolean
+                description: normal pull down.
+              - enum: [100, 101, 102, 103]
+                description: PUPD/R1/R0 pull down type. See MTK_PUPD_SET_R1R0_
+                  defines in dt-bindings/pinctrl/mt65xx.h.
+              - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+                description: RSEL pull down type. See MTK_PULL_SET_RSEL_ defines
+                  in dt-bindings/pinctrl/mt65xx.h.
+
+          bias-pull-up:
+            oneOf:
+              - type: boolean
+                description: normal pull up.
+              - enum: [100, 101, 102, 103]
+                description: PUPD/R1/R0 pull up type. See MTK_PUPD_SET_R1R0_
+                  defines in dt-bindings/pinctrl/mt65xx.h.
+              - enum: [200, 201, 202, 203, 204, 205, 206, 207]
+                description: RSEL pull up type. See MTK_PULL_SET_RSEL_ defines
+                  in dt-bindings/pinctrl/mt65xx.h.
+
+          bias-disable: true
+
+          output-high: true
+
+          output-low: true
+
+          input-enable: true
+
+          input-disable: true
+
+          input-schmitt-enable: true
+
+          input-schmitt-disable: true
+
+        required:
+          - pinmux
+
+        additionalProperties: false
+
+required:
+  - compatible
+  - reg
+  - reg-names
+  - interrupts
+  - interrupt-controller
+  - '#interrupt-cells'
+  - gpio-controller
+  - '#gpio-cells'
+  - gpio-ranges
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/pinctrl/mt65xx.h>
+    #define PINMUX_GPIO0__FUNC_GPIO0 (MTK_PIN_NO(0) | 0)
+    #define PINMUX_GPIO6__FUNC_SCL0 (MTK_PIN_NO(6) | 1)
+    #define PINMUX_GPIO7__FUNC_SDA0 (MTK_PIN_NO(7) | 1)
+
+    pio: pinctrl@10005000 {
+        compatible = "mediatek,mt6895-pinctrl";
+        reg = <0x10005000 0x1000>,
+              <0x11c20000 0x1000>,
+              <0x11c30000 0x1000>,
+              <0x11c40000 0x1000>,
+              <0x11d10000 0x1000>,
+              <0x11d30000 0x1000>,
+              <0x11d40000 0x1000>,
+              <0x11d50000 0x1000>,
+              <0x11d60000 0x1000>,
+              <0x11e10000 0x1000>,
+              <0x11ea0000 0x1000>,
+              <0x11eb0000 0x1000>,
+              <0x11f20000 0x1000>,
+              <0x11f30000 0x1000>,
+              <0x11e50000 0x1000>,
+              <0x11ce0000 0x1000>,
+              <0x11de0000 0x1000>,
+              <0x11fe0000 0x1000>,
+              <0x1c01e000 0x1000>;
+        reg-names = "base", "rm", "rt", "rmm", "bl", "bm", "br",
+                    "brr", "lb", "lm", "rtt", "tr", "tl", "lt",
+                    "eint-w", "eint-e", "eint-s", "eint-n", "eint-c";
+        gpio-controller;
+        #gpio-cells = <2>;
+        gpio-ranges = <&pio 0 0 227>;
+        interrupt-controller;
+        interrupts = <GIC_SPI 259 IRQ_TYPE_LEVEL_HIGH 0>;
+        #interrupt-cells = <2>;
+
+        gpio-pins {
+            pins {
+                pinmux = <PINMUX_GPIO0__FUNC_GPIO0>;
+                bias-pull-up;
+                drive-strength = <6>;
+            };
+        };
+
+        i2c0-pins {
+            pins-bus {
+                pinmux = <PINMUX_GPIO6__FUNC_SCL0>,
+                         <PINMUX_GPIO7__FUNC_SDA0>;
+                bias-pull-up = <MTK_PULL_SET_RSEL_111>;
+                drive-strength-microamp = <1000>;
+            };
+        };
+    };

-- 
2.56.0

Re: [PATCH 2/2] pinctrl: mediatek: Add support for MT6895 pinctrl

[Alexander Letuchiy]

On Sun Nov 8, 2026 at 9:39 PM MSK, sashiko-bot wrote:
> [Severity: Medium]
> Can mtk_pinconf_bias_get_combo() and mtk_pinconf_bias_set_combo() read
> past the end of mt6895_pull_type[]?

Right, mtk_pinconf_get() reaches pull_type[] for the virtual EINT pins
227-246 via debugfs pinconf-pins. I will pad mt6895_pull_type[] with
zero entries in v2.