* [PATCH v2 1/6] mmc: host: omap_hsmmc: Remove setting PBIAS voltage
2017-08-31 10:18 [PATCH v2 0/6] mmc: Add OMAP SDHCI driver Kishon Vijay Abraham I
@ 2017-08-31 10:18 ` Kishon Vijay Abraham I
2017-08-31 10:18 ` [PATCH v2 2/6] regulator: pbias: Select voltage table based on max-voltage Kishon Vijay Abraham I
` (4 subsequent siblings)
5 siblings, 0 replies; 14+ messages in thread
From: Kishon Vijay Abraham I @ 2017-08-31 10:18 UTC (permalink / raw)
To: linux-arm-kernel
PBIAS voltage should be set along with setting vqmmc voltage and
these voltages should be set as part of start_signal_voltage_switch
callback. However since omap_hsmmc is about to be deprecated,
remove setting of PBIAS voltage leaving the PBIAS voltage to be
at the reset value of 3.3V (we'll never have to change this to 1.8V
since UHS mode support will not be added to omap_hsmmc). This will
let pbias regulator driver to be fixed to support a maximum voltage of
3.3V.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/mmc/host/omap_hsmmc.c | 33 ++++++++-------------------------
1 file changed, 8 insertions(+), 25 deletions(-)
diff --git a/drivers/mmc/host/omap_hsmmc.c b/drivers/mmc/host/omap_hsmmc.c
index 3b5e6d11069b..f2a1137be8bc 100644
--- a/drivers/mmc/host/omap_hsmmc.c
+++ b/drivers/mmc/host/omap_hsmmc.c
@@ -147,10 +147,6 @@
#define OMAP_MMC_MAX_CLOCK 52000000
#define DRIVER_NAME "omap_hsmmc"
-#define VDD_1V8 1800000 /* 180000 uV */
-#define VDD_3V0 3000000 /* 300000 uV */
-#define VDD_165_195 (ffs(MMC_VDD_165_195) - 1)
-
/*
* One controller can have multiple slots, like on some omap boards using
* omap.c controller driver. Luckily this is not currently done on any known
@@ -308,8 +304,7 @@ static int omap_hsmmc_disable_supply(struct mmc_host *mmc)
return ret;
}
-static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on,
- int vdd)
+static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on)
{
int ret;
@@ -317,17 +312,6 @@ static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on,
return 0;
if (power_on) {
- if (vdd <= VDD_165_195)
- ret = regulator_set_voltage(host->pbias, VDD_1V8,
- VDD_1V8);
- else
- ret = regulator_set_voltage(host->pbias, VDD_3V0,
- VDD_3V0);
- if (ret < 0) {
- dev_err(host->dev, "pbias set voltage fail\n");
- return ret;
- }
-
if (host->pbias_enabled == 0) {
ret = regulator_enable(host->pbias);
if (ret) {
@@ -350,8 +334,7 @@ static int omap_hsmmc_set_pbias(struct omap_hsmmc_host *host, bool power_on,
return 0;
}
-static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on,
- int vdd)
+static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on)
{
struct mmc_host *mmc = host->mmc;
int ret = 0;
@@ -363,7 +346,7 @@ static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on,
if (IS_ERR(mmc->supply.vmmc))
return 0;
- ret = omap_hsmmc_set_pbias(host, false, 0);
+ ret = omap_hsmmc_set_pbias(host, false);
if (ret)
return ret;
@@ -385,7 +368,7 @@ static int omap_hsmmc_set_power(struct omap_hsmmc_host *host, int power_on,
if (ret)
return ret;
- ret = omap_hsmmc_set_pbias(host, true, vdd);
+ ret = omap_hsmmc_set_pbias(host, true);
if (ret)
goto err_set_voltage;
} else {
@@ -1220,11 +1203,11 @@ static int omap_hsmmc_switch_opcond(struct omap_hsmmc_host *host, int vdd)
clk_disable_unprepare(host->dbclk);
/* Turn the power off */
- ret = omap_hsmmc_set_power(host, 0, 0);
+ ret = omap_hsmmc_set_power(host, 0);
/* Turn the power ON with given VDD 1.8 or 3.0v */
if (!ret)
- ret = omap_hsmmc_set_power(host, 1, vdd);
+ ret = omap_hsmmc_set_power(host, 1);
if (host->dbclk)
clk_prepare_enable(host->dbclk);
@@ -1621,10 +1604,10 @@ static void omap_hsmmc_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
if (ios->power_mode != host->power_mode) {
switch (ios->power_mode) {
case MMC_POWER_OFF:
- omap_hsmmc_set_power(host, 0, 0);
+ omap_hsmmc_set_power(host, 0);
break;
case MMC_POWER_UP:
- omap_hsmmc_set_power(host, 1, ios->vdd);
+ omap_hsmmc_set_power(host, 1);
break;
case MMC_POWER_ON:
do_send_init_stream = 1;
--
2.11.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 2/6] regulator: pbias: Select voltage table based on max-voltage
2017-08-31 10:18 [PATCH v2 0/6] mmc: Add OMAP SDHCI driver Kishon Vijay Abraham I
2017-08-31 10:18 ` [PATCH v2 1/6] mmc: host: omap_hsmmc: Remove setting PBIAS voltage Kishon Vijay Abraham I
@ 2017-08-31 10:18 ` Kishon Vijay Abraham I
2017-08-31 11:55 ` Applied "regulator: pbias: Select voltage table based on max-voltage" to the regulator tree Mark Brown
2017-08-31 10:18 ` [PATCH v2 3/6] ARM: dts: dra7: Increase max-voltage of pbias regulator Kishon Vijay Abraham I
` (3 subsequent siblings)
5 siblings, 1 reply; 14+ messages in thread
From: Kishon Vijay Abraham I @ 2017-08-31 10:18 UTC (permalink / raw)
To: linux-arm-kernel
From: Ravikumar Kattekola <rk@ti.com>
Reference manuals of OMAP5x and DRA7x have been updated to reflect
the PBIAS regulator max-voltage as 3.3V instead of 3.0V, while OMAP3x
and OMAP4x are still quoting 3.0V. So, as of now, the pbias driver
needs to support both 3.0V and 3.3V IO voltage based on the max-voltage
supported by the PBIAS regulator.
Document reference:
SWPU249AF - OMAP543x Technical reference manual - August 2016
SPRUI30C ? DRA75x, DRA74x Technical reference manual November 2016
Tested on:
DRA75x PG 2.0 REV H EVM
Signed-off-by: Ravikumar Kattekola <rk@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/regulator/pbias-regulator.c | 21 ++++++++++++++++++---
1 file changed, 18 insertions(+), 3 deletions(-)
diff --git a/drivers/regulator/pbias-regulator.c b/drivers/regulator/pbias-regulator.c
index 0cb76ba29e84..8f782d22fdbe 100644
--- a/drivers/regulator/pbias-regulator.c
+++ b/drivers/regulator/pbias-regulator.c
@@ -34,6 +34,8 @@ struct pbias_reg_info {
u32 vmode;
unsigned int enable_time;
char *name;
+ const unsigned int *pbias_volt_table;
+ int n_voltages;
};
struct pbias_regulator_data {
@@ -49,11 +51,16 @@ struct pbias_of_data {
unsigned int offset;
};
-static const unsigned int pbias_volt_table[] = {
+static const unsigned int pbias_volt_table_3_0V[] = {
1800000,
3000000
};
+static const unsigned int pbias_volt_table_3_3V[] = {
+ 1800000,
+ 3300000
+};
+
static const struct regulator_ops pbias_regulator_voltage_ops = {
.list_voltage = regulator_list_voltage_table,
.get_voltage_sel = regulator_get_voltage_sel_regmap,
@@ -69,6 +76,8 @@ static const struct pbias_reg_info pbias_mmc_omap2430 = {
.vmode = BIT(0),
.disable_val = 0,
.enable_time = 100,
+ .pbias_volt_table = pbias_volt_table_3_0V,
+ .n_voltages = 2,
.name = "pbias_mmc_omap2430"
};
@@ -77,6 +86,8 @@ static const struct pbias_reg_info pbias_sim_omap3 = {
.enable_mask = BIT(9),
.vmode = BIT(8),
.enable_time = 100,
+ .pbias_volt_table = pbias_volt_table_3_0V,
+ .n_voltages = 2,
.name = "pbias_sim_omap3"
};
@@ -86,6 +97,8 @@ static const struct pbias_reg_info pbias_mmc_omap4 = {
.disable_val = BIT(25),
.vmode = BIT(21),
.enable_time = 100,
+ .pbias_volt_table = pbias_volt_table_3_0V,
+ .n_voltages = 2,
.name = "pbias_mmc_omap4"
};
@@ -95,6 +108,8 @@ static const struct pbias_reg_info pbias_mmc_omap5 = {
.disable_val = BIT(25),
.vmode = BIT(21),
.enable_time = 100,
+ .pbias_volt_table = pbias_volt_table_3_3V,
+ .n_voltages = 2,
.name = "pbias_mmc_omap5"
};
@@ -199,8 +214,8 @@ static int pbias_regulator_probe(struct platform_device *pdev)
drvdata[data_idx].desc.owner = THIS_MODULE;
drvdata[data_idx].desc.type = REGULATOR_VOLTAGE;
drvdata[data_idx].desc.ops = &pbias_regulator_voltage_ops;
- drvdata[data_idx].desc.volt_table = pbias_volt_table;
- drvdata[data_idx].desc.n_voltages = 2;
+ drvdata[data_idx].desc.volt_table = info->pbias_volt_table;
+ drvdata[data_idx].desc.n_voltages = info->n_voltages;
drvdata[data_idx].desc.enable_time = info->enable_time;
drvdata[data_idx].desc.vsel_reg = offset;
drvdata[data_idx].desc.vsel_mask = info->vmode;
--
2.11.0
^ permalink raw reply related [flat|nested] 14+ messages in thread* [PATCH v2 5/6] mmc: sdhci-omap: Add OMAP SDHCI driver
2017-08-31 10:18 [PATCH v2 0/6] mmc: Add OMAP SDHCI driver Kishon Vijay Abraham I
` (3 preceding siblings ...)
2017-08-31 10:18 ` [PATCH v2 4/6] dt-bindings: sdhci-omap: Add bindings for the sdhci-omap controller Kishon Vijay Abraham I
@ 2017-08-31 10:18 ` Kishon Vijay Abraham I
2017-08-31 10:18 ` [PATCH v2 6/6] MAINTAINERS: Add TI OMAP SDHCI Maintainer Kishon Vijay Abraham I
5 siblings, 0 replies; 14+ messages in thread
From: Kishon Vijay Abraham I @ 2017-08-31 10:18 UTC (permalink / raw)
To: linux-arm-kernel
Create a new sdhci-omap driver to configure the eMMC/SD/SDIO controller
in TI's OMAP SoCs making use of the SDHCI core library. For OMAP specific
configurations, populate sdhci_ops with OMAP specific callbacks and use
SDHCI quirks.
Enable only high speed mode for both SD and eMMC here and add other
UHS mode support later.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
---
drivers/mmc/host/Kconfig | 12 +
drivers/mmc/host/Makefile | 1 +
drivers/mmc/host/sdhci-omap.c | 604 ++++++++++++++++++++++++++++++++++++++++++
3 files changed, 617 insertions(+)
create mode 100644 drivers/mmc/host/sdhci-omap.c
diff --git a/drivers/mmc/host/Kconfig b/drivers/mmc/host/Kconfig
index 02179ed2a40d..03178c42efbb 100644
--- a/drivers/mmc/host/Kconfig
+++ b/drivers/mmc/host/Kconfig
@@ -899,3 +899,15 @@ config MMC_SDHCI_XENON
This selects Marvell Xenon eMMC/SD/SDIO SDHCI.
If you have a controller with this interface, say Y or M here.
If unsure, say N.
+
+config MMC_SDHCI_OMAP
+ tristate "TI SDHCI Controller Support"
+ depends on MMC_SDHCI_PLTFM && OF
+ help
+ This selects the Secure Digital Host Controller Interface (SDHCI)
+ support present in TI's DRA7 SOCs. The controller supports
+ SD/MMC/SDIO devices.
+
+ If you have a controller with this interface, say Y or M here.
+
+ If unsure, say N.
diff --git a/drivers/mmc/host/Makefile b/drivers/mmc/host/Makefile
index 303f5cd46cd9..2b5a8133948d 100644
--- a/drivers/mmc/host/Makefile
+++ b/drivers/mmc/host/Makefile
@@ -89,6 +89,7 @@ obj-$(CONFIG_MMC_SDHCI_MSM) += sdhci-msm.o
obj-$(CONFIG_MMC_SDHCI_ST) += sdhci-st.o
obj-$(CONFIG_MMC_SDHCI_MICROCHIP_PIC32) += sdhci-pic32.o
obj-$(CONFIG_MMC_SDHCI_BRCMSTB) += sdhci-brcmstb.o
+obj-$(CONFIG_MMC_SDHCI_OMAP) += sdhci-omap.o
ifeq ($(CONFIG_CB710_DEBUG),y)
CFLAGS-cb710-mmc += -DDEBUG
diff --git a/drivers/mmc/host/sdhci-omap.c b/drivers/mmc/host/sdhci-omap.c
new file mode 100644
index 000000000000..cdbd3e1b894e
--- /dev/null
+++ b/drivers/mmc/host/sdhci-omap.c
@@ -0,0 +1,604 @@
+/**
+ * SDHCI Controller driver for TI's OMAP SoCs
+ *
+ * Copyright (C) 2017 Texas Instruments
+ * Author: Kishon Vijay Abraham I <kishon@ti.com>
+ *
+ * This program is free software: you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 of
+ * the License as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/delay.h>
+#include <linux/mmc/slot-gpio.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pm_runtime.h>
+#include <linux/regulator/consumer.h>
+
+#include "sdhci-pltfm.h"
+
+#define SDHCI_OMAP_CON 0x12c
+#define CON_DW8 BIT(5)
+#define CON_DMA_MASTER BIT(20)
+#define CON_INIT BIT(1)
+#define CON_OD BIT(0)
+
+#define SDHCI_OMAP_CMD 0x20c
+
+#define SDHCI_OMAP_HCTL 0x228
+#define HCTL_SDBP BIT(8)
+#define HCTL_SDVS_SHIFT 9
+#define HCTL_SDVS_MASK (0x7 << HCTL_SDVS_SHIFT)
+#define HCTL_SDVS_33 (0x7 << HCTL_SDVS_SHIFT)
+#define HCTL_SDVS_30 (0x6 << HCTL_SDVS_SHIFT)
+#define HCTL_SDVS_18 (0x5 << HCTL_SDVS_SHIFT)
+
+#define SDHCI_OMAP_SYSCTL 0x22c
+#define SYSCTL_CEN BIT(2)
+#define SYSCTL_CLKD_SHIFT 6
+#define SYSCTL_CLKD_MASK 0x3ff
+
+#define SDHCI_OMAP_STAT 0x230
+
+#define SDHCI_OMAP_IE 0x234
+#define INT_CC_EN BIT(0)
+
+#define SDHCI_OMAP_AC12 0x23c
+#define AC12_V1V8_SIGEN BIT(19)
+
+#define SDHCI_OMAP_CAPA 0x240
+#define CAPA_VS33 BIT(24)
+#define CAPA_VS30 BIT(25)
+#define CAPA_VS18 BIT(26)
+
+#define SDHCI_OMAP_TIMEOUT 1 /* 1 msec */
+
+#define SYSCTL_CLKD_MAX 0x3FF
+
+#define IOV_1V8 1800000 /* 180000 uV */
+#define IOV_3V0 3000000 /* 300000 uV */
+#define IOV_3V3 3300000 /* 330000 uV */
+
+struct sdhci_omap_data {
+ u32 offset;
+};
+
+struct sdhci_omap_host {
+ void __iomem *base;
+ struct device *dev;
+ struct regulator *pbias;
+ bool pbias_enabled;
+ struct sdhci_host *host;
+ u8 bus_mode;
+ u8 power_mode;
+};
+
+static inline u32 sdhci_omap_readl(struct sdhci_omap_host *host,
+ unsigned int offset)
+{
+ return readl(host->base + offset);
+}
+
+static inline void sdhci_omap_writel(struct sdhci_omap_host *host,
+ unsigned int offset, u32 data)
+{
+ writel(data, host->base + offset);
+}
+
+static int sdhci_omap_set_pbias(struct sdhci_omap_host *omap_host,
+ bool power_on, unsigned int iov)
+{
+ int ret;
+ struct device *dev = omap_host->dev;
+
+ if (IS_ERR(omap_host->pbias))
+ return 0;
+
+ if (power_on) {
+ ret = regulator_set_voltage(omap_host->pbias, iov, iov);
+ if (ret) {
+ dev_err(dev, "pbias set voltage failed\n");
+ return ret;
+ }
+
+ if (omap_host->pbias_enabled)
+ return 0;
+
+ ret = regulator_enable(omap_host->pbias);
+ if (ret) {
+ dev_err(dev, "pbias reg enable fail\n");
+ return ret;
+ }
+
+ omap_host->pbias_enabled = true;
+ } else {
+ if (!omap_host->pbias_enabled)
+ return 0;
+
+ ret = regulator_disable(omap_host->pbias);
+ if (ret) {
+ dev_err(dev, "pbias reg disable fail\n");
+ return ret;
+ }
+ omap_host->pbias_enabled = false;
+ }
+
+ return 0;
+}
+
+static int sdhci_omap_enable_iov(struct sdhci_omap_host *omap_host,
+ unsigned int iov)
+{
+ int ret;
+ struct sdhci_host *host = omap_host->host;
+ struct mmc_host *mmc = host->mmc;
+
+ ret = sdhci_omap_set_pbias(omap_host, false, 0);
+ if (ret)
+ return ret;
+
+ if (!IS_ERR(mmc->supply.vqmmc)) {
+ ret = regulator_set_voltage(mmc->supply.vqmmc, iov, iov);
+ if (ret) {
+ dev_err(mmc_dev(mmc), "vqmmc set voltage failed\n");
+ return ret;
+ }
+ }
+
+ ret = sdhci_omap_set_pbias(omap_host, true, iov);
+ if (ret)
+ return ret;
+
+ return 0;
+}
+
+static void sdhci_omap_conf_bus_power(struct sdhci_omap_host *omap_host,
+ unsigned char signal_voltage)
+{
+ u32 reg;
+ ktime_t timeout;
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_HCTL);
+ reg &= ~HCTL_SDVS_MASK;
+
+ if (signal_voltage == MMC_SIGNAL_VOLTAGE_330)
+ reg |= HCTL_SDVS_33;
+ else
+ reg |= HCTL_SDVS_18;
+
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, reg);
+
+ reg |= HCTL_SDBP;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_HCTL, reg);
+
+ /* wait 1ms */
+ timeout = ktime_add_ms(ktime_get(), SDHCI_OMAP_TIMEOUT);
+ while (!(sdhci_omap_readl(omap_host, SDHCI_OMAP_HCTL) & HCTL_SDBP)) {
+ if (WARN_ON(ktime_after(ktime_get(), timeout)))
+ return;
+ usleep_range(5, 10);
+ }
+}
+
+static int sdhci_omap_start_signal_voltage_switch(struct mmc_host *mmc,
+ struct mmc_ios *ios)
+{
+ u32 reg;
+ int ret;
+ unsigned int iov;
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_omap_host *omap_host;
+ struct device *dev;
+
+ pltfm_host = sdhci_priv(host);
+ omap_host = sdhci_pltfm_priv(pltfm_host);
+ dev = omap_host->dev;
+
+ if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_330) {
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
+ if (!(reg & CAPA_VS33))
+ return -EOPNOTSUPP;
+
+ sdhci_omap_conf_bus_power(omap_host, ios->signal_voltage);
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
+ reg &= ~AC12_V1V8_SIGEN;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_AC12, reg);
+
+ iov = IOV_3V3;
+ } else if (ios->signal_voltage == MMC_SIGNAL_VOLTAGE_180) {
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
+ if (!(reg & CAPA_VS18))
+ return -EOPNOTSUPP;
+
+ sdhci_omap_conf_bus_power(omap_host, ios->signal_voltage);
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_AC12);
+ reg |= AC12_V1V8_SIGEN;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_AC12, reg);
+
+ iov = IOV_1V8;
+ } else {
+ return -EOPNOTSUPP;
+ }
+
+ ret = sdhci_omap_enable_iov(omap_host, iov);
+ if (ret) {
+ dev_err(dev, "failed to switch IO voltage to %dmV\n", iov);
+ return ret;
+ }
+
+ dev_dbg(dev, "IO voltage switched to %dmV\n", iov);
+ return 0;
+}
+
+static void sdhci_omap_set_bus_mode(struct sdhci_omap_host *omap_host,
+ unsigned int mode)
+{
+ u32 reg;
+
+ if (omap_host->bus_mode == mode)
+ return;
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+ if (mode == MMC_BUSMODE_OPENDRAIN)
+ reg |= CON_OD;
+ else
+ reg &= ~CON_OD;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+
+ omap_host->bus_mode = mode;
+}
+
+void sdhci_omap_set_ios(struct mmc_host *mmc, struct mmc_ios *ios)
+{
+ struct sdhci_host *host = mmc_priv(mmc);
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_omap_host *omap_host;
+
+ pltfm_host = sdhci_priv(host);
+ omap_host = sdhci_pltfm_priv(pltfm_host);
+
+ sdhci_omap_set_bus_mode(omap_host, ios->bus_mode);
+ sdhci_set_ios(mmc, ios);
+}
+
+static u16 sdhci_omap_calc_divisor(struct sdhci_pltfm_host *host,
+ unsigned int clock)
+{
+ u16 dsor;
+
+ dsor = DIV_ROUND_UP(clk_get_rate(host->clk), clock);
+ if (dsor > SYSCTL_CLKD_MAX)
+ dsor = SYSCTL_CLKD_MAX;
+
+ return dsor;
+}
+
+static void sdhci_omap_start_clock(struct sdhci_omap_host *omap_host)
+{
+ u32 reg;
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCTL);
+ reg |= SYSCTL_CEN;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCTL, reg);
+}
+
+static void sdhci_omap_stop_clock(struct sdhci_omap_host *omap_host)
+{
+ u32 reg;
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_SYSCTL);
+ reg &= ~SYSCTL_CEN;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_SYSCTL, reg);
+}
+
+static void sdhci_omap_set_clock(struct sdhci_host *host, unsigned int clock)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
+ unsigned long clkdiv;
+
+ sdhci_omap_stop_clock(omap_host);
+
+ clkdiv = sdhci_omap_calc_divisor(pltfm_host, clock);
+ clkdiv = (clkdiv & SYSCTL_CLKD_MASK) << SYSCTL_CLKD_SHIFT;
+ sdhci_enable_clk(host, clkdiv);
+
+ sdhci_omap_start_clock(omap_host);
+}
+
+void sdhci_omap_set_power(struct sdhci_host *host, unsigned char mode,
+ unsigned short vdd)
+{
+ struct mmc_host *mmc = host->mmc;
+
+ mmc_regulator_set_ocr(mmc, mmc->supply.vmmc, vdd);
+}
+
+static int sdhci_omap_enable_dma(struct sdhci_host *host)
+{
+ u32 reg;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+ reg |= CON_DMA_MASTER;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+
+ return 0;
+}
+
+unsigned int sdhci_omap_get_min_clock(struct sdhci_host *host)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+
+ return clk_get_rate(pltfm_host->clk) / SYSCTL_CLKD_MAX;
+}
+
+static void sdhci_omap_set_bus_width(struct sdhci_host *host, int width)
+{
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
+ u32 reg;
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+ if (width == MMC_BUS_WIDTH_8)
+ reg |= CON_DW8;
+ else
+ reg &= ~CON_DW8;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+
+ sdhci_set_bus_width(host, width);
+}
+
+static void sdhci_omap_init_74_clocks(struct sdhci_host *host, u8 power_mode)
+{
+ u32 reg;
+ ktime_t timeout;
+ struct sdhci_pltfm_host *pltfm_host = sdhci_priv(host);
+ struct sdhci_omap_host *omap_host = sdhci_pltfm_priv(pltfm_host);
+
+ if (omap_host->power_mode == power_mode)
+ return;
+
+ if (power_mode != MMC_POWER_ON)
+ return;
+
+ disable_irq(host->irq);
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+ reg |= CON_INIT;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CMD, 0x0);
+
+ /* wait 1ms */
+ timeout = ktime_add_ms(ktime_get(), SDHCI_OMAP_TIMEOUT);
+ while (!(sdhci_omap_readl(omap_host, SDHCI_OMAP_STAT) & INT_CC_EN)) {
+ if (WARN_ON(ktime_after(ktime_get(), timeout)))
+ return;
+ usleep_range(5, 10);
+ }
+
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CON);
+ reg &= ~CON_INIT;
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CON, reg);
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_STAT, INT_CC_EN);
+
+ enable_irq(host->irq);
+
+ omap_host->power_mode = power_mode;
+}
+
+static struct sdhci_ops sdhci_omap_ops = {
+ .set_clock = sdhci_omap_set_clock,
+ .set_power = sdhci_omap_set_power,
+ .enable_dma = sdhci_omap_enable_dma,
+ .get_max_clock = sdhci_pltfm_clk_get_max_clock,
+ .get_min_clock = sdhci_omap_get_min_clock,
+ .set_bus_width = sdhci_omap_set_bus_width,
+ .platform_send_init_74_clocks = sdhci_omap_init_74_clocks,
+ .reset = sdhci_reset,
+ .set_uhs_signaling = sdhci_set_uhs_signaling,
+};
+
+static int sdhci_omap_set_capabilities(struct sdhci_omap_host *omap_host)
+{
+ u32 reg;
+ int ret = 0;
+ struct device *dev = omap_host->dev;
+ struct regulator *vqmmc;
+
+ vqmmc = regulator_get(dev, "vqmmc");
+ if (IS_ERR(vqmmc)) {
+ ret = PTR_ERR(vqmmc);
+ goto reg_put;
+ }
+
+ /* voltage capabilities might be set by boot loader, clear it */
+ reg = sdhci_omap_readl(omap_host, SDHCI_OMAP_CAPA);
+ reg &= ~(CAPA_VS18 | CAPA_VS30 | CAPA_VS33);
+
+ if (regulator_is_supported_voltage(vqmmc, IOV_3V3, IOV_3V3))
+ reg |= CAPA_VS33;
+ if (regulator_is_supported_voltage(vqmmc, IOV_1V8, IOV_1V8))
+ reg |= CAPA_VS18;
+
+ sdhci_omap_writel(omap_host, SDHCI_OMAP_CAPA, reg);
+
+reg_put:
+ regulator_put(vqmmc);
+
+ return ret;
+}
+
+static const struct sdhci_pltfm_data sdhci_omap_pdata = {
+ .quirks = SDHCI_QUIRK_BROKEN_CARD_DETECTION |
+ SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK |
+ SDHCI_QUIRK_CAP_CLOCK_BASE_BROKEN |
+ SDHCI_QUIRK_NO_HISPD_BIT |
+ SDHCI_QUIRK_BROKEN_ADMA_ZEROLEN_DESC,
+ .quirks2 = SDHCI_QUIRK2_NO_1_8_V |
+ SDHCI_QUIRK2_ACMD23_BROKEN |
+ SDHCI_QUIRK2_RSP_136_HAS_CRC,
+ .ops = &sdhci_omap_ops,
+};
+
+static const struct sdhci_omap_data dra7_data = {
+ .offset = 0x200,
+};
+
+static const struct of_device_id omap_sdhci_match[] = {
+ { .compatible = "ti,dra7-sdhci", .data = &dra7_data },
+ {},
+};
+MODULE_DEVICE_TABLE(of, omap_sdhci_match);
+
+static int sdhci_omap_probe(struct platform_device *pdev)
+{
+ int ret;
+ u32 offset;
+ struct device *dev = &pdev->dev;
+ struct sdhci_host *host;
+ struct sdhci_pltfm_host *pltfm_host;
+ struct sdhci_omap_host *omap_host;
+ struct mmc_host *mmc;
+ const struct of_device_id *match;
+ struct sdhci_omap_data *data;
+
+ match = of_match_device(omap_sdhci_match, dev);
+ if (!match)
+ return -EINVAL;
+
+ data = (struct sdhci_omap_data *)match->data;
+ if (!data) {
+ dev_err(dev, "no sdhci omap data\n");
+ return -EINVAL;
+ }
+ offset = data->offset;
+
+ host = sdhci_pltfm_init(pdev, &sdhci_omap_pdata,
+ sizeof(*omap_host));
+ if (IS_ERR(host)) {
+ dev_err(dev, "Failed sdhci_pltfm_init\n");
+ return PTR_ERR(host);
+ }
+
+ pltfm_host = sdhci_priv(host);
+ omap_host = sdhci_pltfm_priv(pltfm_host);
+ omap_host->host = host;
+ omap_host->base = host->ioaddr;
+ omap_host->dev = dev;
+ host->ioaddr += offset;
+
+ mmc = host->mmc;
+ ret = mmc_of_parse(mmc);
+ if (ret)
+ goto err_pltfm_free;
+
+ pltfm_host->clk = devm_clk_get(dev, "fck");
+ if (IS_ERR(pltfm_host->clk)) {
+ ret = PTR_ERR(pltfm_host->clk);
+ goto err_pltfm_free;
+ }
+
+ ret = clk_set_rate(pltfm_host->clk, mmc->f_max);
+ if (ret) {
+ dev_err(dev, "failed to set clock to %d\n", mmc->f_max);
+ goto err_pltfm_free;
+ }
+
+ omap_host->pbias = devm_regulator_get_optional(dev, "pbias");
+ if (IS_ERR(omap_host->pbias)) {
+ ret = PTR_ERR(omap_host->pbias);
+ if (ret != -ENODEV)
+ goto err_pltfm_free;
+ dev_dbg(dev, "unable to get pbias regulator %d\n", ret);
+ }
+ omap_host->pbias_enabled = false;
+
+ /*
+ * omap_device_pm_domain has callbacks to enable the main
+ * functional clock, interface clock and also configure the
+ * SYSCONFIG register of omap devices. The callback will be invoked
+ * as part of pm_runtime_get_sync.
+ */
+ pm_runtime_enable(dev);
+ ret = pm_runtime_get_sync(dev);
+ if (ret < 0) {
+ dev_err(dev, "pm_runtime_get_sync failed\n");
+ pm_runtime_put_noidle(dev);
+ goto err_rpm_disable;
+ }
+
+ ret = sdhci_omap_set_capabilities(omap_host);
+ if (ret) {
+ dev_err(dev, "failed to set system capabilities\n");
+ goto err_put_sync;
+ }
+
+ host->mmc_host_ops.get_ro = mmc_gpio_get_ro;
+ host->mmc_host_ops.start_signal_voltage_switch =
+ sdhci_omap_start_signal_voltage_switch;
+ host->mmc_host_ops.set_ios = sdhci_omap_set_ios;
+
+ sdhci_read_caps(host);
+ host->caps |= SDHCI_CAN_DO_ADMA2;
+
+ ret = sdhci_add_host(host);
+ if (ret)
+ goto err_put_sync;
+
+ return 0;
+
+err_put_sync:
+ pm_runtime_put_sync(dev);
+
+err_rpm_disable:
+ pm_runtime_disable(dev);
+
+err_pltfm_free:
+ sdhci_pltfm_free(pdev);
+ return ret;
+}
+
+static int sdhci_omap_remove(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct sdhci_host *host = platform_get_drvdata(pdev);
+
+ sdhci_remove_host(host, true);
+ pm_runtime_put_sync(dev);
+ pm_runtime_disable(dev);
+ sdhci_pltfm_free(pdev);
+
+ return 0;
+}
+
+static struct platform_driver sdhci_omap_driver = {
+ .probe = sdhci_omap_probe,
+ .remove = sdhci_omap_remove,
+ .driver = {
+ .name = "sdhci-omap",
+ .of_match_table = omap_sdhci_match,
+ },
+};
+
+module_platform_driver(sdhci_omap_driver);
+
+MODULE_DESCRIPTION("SDHCI driver for OMAP SoCs");
+MODULE_AUTHOR("Texas Instruments Inc.");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:sdhci_omap");
--
2.11.0
^ permalink raw reply related [flat|nested] 14+ messages in thread