* [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC
@ 2025-06-11 13:05 Yannic Moog
2025-06-11 13:05 ` [PATCH v3 1/2] dt-bindings: add imx95-libra-rdk-fpsc Yannic Moog
` (3 more replies)
0 siblings, 4 replies; 7+ messages in thread
From: Yannic Moog @ 2025-06-11 13:05 UTC (permalink / raw)
To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo,
Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam,
Catalin Marinas, Will Deacon
Cc: upstream, Benjamin Hahn, Teresa Remmet, Yashwanth Varakala,
Jan Remmet, devicetree, linux-kernel, imx, linux-arm-kernel,
Conor Dooley, Yannic Moog
The Libra i.MX 95 is a SBC that consists of the Libra base board
and the phyCORE i.MX 95 FPSC SoM.
This series adds its binding and device trees.
---
Changes in v3:
- fix more style issues
- remove the rs232/485 gpio hog -> switch on the board is used instead
- remove erroneously added build artefacts
- Link to v2: https://lore.kernel.org/r/20250509-wip-y-moog-phytec-de-imx95-libra-v2-2-b241a915f2be@phytec.de
Changes in v2:
- fix indentation error in bindings
- align alias naming with FPSC enumeration
- Link to v1: https://lore.kernel.org/r/20250507-wip-y-moog-phytec-de-imx95-libra-v1-0-4b73843ad4cd@phytec.de
---
Yannic Moog (2):
dt-bindings: add imx95-libra-rdk-fpsc
arm64: dts: add imx95-libra-rdk-fpsc board
Documentation/devicetree/bindings/arm/fsl.yaml | 7 +
arch/arm64/boot/dts/freescale/Makefile | 1 +
.../boot/dts/freescale/imx95-libra-rdk-fpsc.dts | 318 ++++++++++
.../boot/dts/freescale/imx95-phycore-fpsc.dtsi | 656 +++++++++++++++++++++
4 files changed, 982 insertions(+)
---
base-commit: 68087d05675e3ac0ed632bc7b175abf06617c584
change-id: 20250415-wip-y-moog-phytec-de-imx95-libra-27c9ce555b91
Best regards,
--
Yannic Moog <y.moog@phytec.de>
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v3 1/2] dt-bindings: add imx95-libra-rdk-fpsc 2025-06-11 13:05 [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Yannic Moog @ 2025-06-11 13:05 ` Yannic Moog 2025-06-11 13:05 ` [PATCH v3 2/2] arm64: dts: add imx95-libra-rdk-fpsc board Yannic Moog ` (2 subsequent siblings) 3 siblings, 0 replies; 7+ messages in thread From: Yannic Moog @ 2025-06-11 13:05 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon Cc: upstream, Benjamin Hahn, Teresa Remmet, Yashwanth Varakala, Jan Remmet, devicetree, linux-kernel, imx, linux-arm-kernel, Conor Dooley, Yannic Moog imx95-libra-rdk-fpsc is a development board based on the phyCORE-i.MX 95 Plus FPSC SoM. Add its description and binding. Acked-by: Conor Dooley <conor.dooley@microchip.com> Signed-off-by: Yannic Moog <y.moog@phytec.de> --- Documentation/devicetree/bindings/arm/fsl.yaml | 7 +++++++ 1 file changed, 7 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/fsl.yaml b/Documentation/devicetree/bindings/arm/fsl.yaml index d3b5e6923e4166e35760c17c772aa0195137de93..8b0411f20f2ed67733ed6059cd6d1d86415c98a3 100644 --- a/Documentation/devicetree/bindings/arm/fsl.yaml +++ b/Documentation/devicetree/bindings/arm/fsl.yaml @@ -1395,6 +1395,13 @@ properties: - fsl,imx95-19x19-evk # i.MX95 19x19 EVK Board - const: fsl,imx95 + - description: PHYTEC i.MX 95 FPSC based Boards + items: + - enum: + - phytec,imx95-libra-rdk-fpsc # Libra-i.MX 95 FPSC + - const: phytec,imx95-phycore-fpsc # phyCORE-i.MX 95 FPSC + - const: fsl,imx95 + - description: i.MXRT1050 based Boards items: - enum: -- 2.43.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [PATCH v3 2/2] arm64: dts: add imx95-libra-rdk-fpsc board 2025-06-11 13:05 [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Yannic Moog 2025-06-11 13:05 ` [PATCH v3 1/2] dt-bindings: add imx95-libra-rdk-fpsc Yannic Moog @ 2025-06-11 13:05 ` Yannic Moog 2025-06-11 16:41 ` Frank Li 2025-06-12 20:12 ` [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Rob Herring (Arm) 2025-07-11 7:30 ` Shawn Guo 3 siblings, 1 reply; 7+ messages in thread From: Yannic Moog @ 2025-06-11 13:05 UTC (permalink / raw) To: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon Cc: upstream, Benjamin Hahn, Teresa Remmet, Yashwanth Varakala, Jan Remmet, devicetree, linux-kernel, imx, linux-arm-kernel, Yannic Moog Add device tree for the Libra-i.MX 95 FPSC board. The Libra is a pure development board and has hardware to support FPSC-24-A.0 set of features. The phyCORE-i.MX 95 FPSC [1] SoM uses only a subset of the hardware features of the Libra board. The phyCORE-i.MX 95 FPSC itself is a System on Module designed around the i.MX 95 SoC. The SoM and board utilize the Future Proof Solder Core [2] BGA standard to connect to each other. To be able to easily map FPSC interface names to SoC interfaces, the FPSC interface names are added as inline comments. Example: &lpi2c5 { /* I2C2 */ pinctrl-0 = <&pinctrl_lpi2c5>; [...] }; Here, I2C2 is the FPSC interface name. The lpi2c5 instance of the i.MX 95 SoC is used to fulfill the i2c functionality and its signals are routed to the FPSC I2C2 signal pins: pinctrl_lpi2c5: lpi2c5grp { fsl,pins = < IMX95_PAD_GPIO_IO22__LPI2C5_SDA 0x40000b9e /* I2C2_SDA */ IMX95_PAD_GPIO_IO23__LPI2C5_SCL 0x40000b9e /* I2C2_SCL */ >; }; [1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-95-fpsc/ [2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc/ Signed-off-by: Yannic Moog <y.moog@phytec.de> --- arch/arm64/boot/dts/freescale/Makefile | 1 + .../boot/dts/freescale/imx95-libra-rdk-fpsc.dts | 318 ++++++++++ .../boot/dts/freescale/imx95-phycore-fpsc.dtsi | 656 +++++++++++++++++++++ 3 files changed, 975 insertions(+) diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile index 0b473a23d12008ff79d6467d9e1c7ab2c4d6a9a6..656a7ec547b20c4fd3d8f4c54ba149c13b57b386 100644 --- a/arch/arm64/boot/dts/freescale/Makefile +++ b/arch/arm64/boot/dts/freescale/Makefile @@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx95-15x15-evk-pcie0-ep.dtb imx95-19x19-evk-pcie0-ep-dtbs += imx95-19x19-evk.dtb imx-pcie0-ep.dtbo imx95-19x19-evk-pcie1-ep-dtbs += imx95-19x19-evk.dtb imx-pcie1-ep.dtbo dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-pcie0-ep.dtb imx95-19x19-evk-pcie1-ep.dtb +dtb-$(CONFIG_ARCH_MXC) += imx95-libra-rdk-fpsc.dtb imx8mm-kontron-dl-dtbs := imx8mm-kontron-bl.dtb imx8mm-kontron-dl.dtbo diff --git a/arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dts b/arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dts new file mode 100644 index 0000000000000000000000000000000000000000..26c2df9b1b60a89fbd8456db6aec8c8d72abbd3e --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dts @@ -0,0 +1,318 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2025 PHYTEC Messtechnik GmbH + */ + +/dts-v1/; + +#include <dt-bindings/leds/leds-pca9532.h> +#include <dt-bindings/pwm/pwm.h> + +#include "imx95-phycore-fpsc.dtsi" + +/ { + compatible = "phytec,imx95-libra-rdk-fpsc", + "phytec,imx95-phycore-fpsc", "fsl,imx95"; + model = "PHYTEC Libra i.MX95 RDK FPSC"; + + aliases { + can1 = &flexcan2; + can2 = &flexcan1; + ethernet0 = &enetc_port0; + serial0 = &lpuart7; + serial1 = &lpuart8; + }; + + chosen { + stdout-path = &lpuart7; + }; + + backlight_lvds0: backlight0 { + compatible = "pwm-backlight"; + pinctrl-0 = <&pinctrl_lvds0>; + power-supply = <®_vdd_12v0>; + status = "disabled"; + }; + + transceiver1: can-phy { + compatible = "ti,tcan1043"; + #phy-cells = <0>; + max-bitrate = <8000000>; + enable-gpios = <&gpio_expander 10 GPIO_ACTIVE_LOW>; + }; + + transceiver2: can-phy { + compatible = "ti,tcan1043"; + #phy-cells = <0>; + max-bitrate = <8000000>; + enable-gpios = <&gpio_expander 9 GPIO_ACTIVE_LOW>; + }; + + panel0_lvds: panel-lvds0 { + backlight = <&backlight_lvds0>; + power-supply = <®_vdd_3v3>; + status = "disabled"; + }; + + reg_vdd_12v0: regulator-vdd-12v0 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <12000000>; + regulator-min-microvolt = <12000000>; + regulator-name = "VDD_12V0"; + }; + + reg_vdd_1v8: regulator-vdd-1v8 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "VDD_1V8"; + }; + + reg_vdd_3v3: regulator-vdd-3v3 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "VDD_3V3"; + }; + + reg_vdd_5v0: regulator-vdd-5v0 { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <5000000>; + regulator-min-microvolt = <5000000>; + regulator-name = "VDD_5V0"; + }; +}; + +&enetc_port0 { + phy-handle = <ðphy0>; + status = "okay"; +}; + +&enetc_port2 { + managed = "in-band-status"; + phy-handle = <ðphy2>; + phy-mode = "10gbase-r"; +}; + +/* CAN FD */ +&flexcan1 { + phys = <&transceiver1>; + status = "okay"; +}; + +&flexcan2 { + phys = <&transceiver2>; + status = "okay"; +}; + +/* SPI-NOR */ +&flexspi1 { + pinctrl-0 = <&pinctrl_flexspi>; + pinctrl-names = "default"; + status = "okay"; + + spi_nor: flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <166000000>; + spi-rx-bus-width = <4>; + spi-tx-bus-width = <4>; + vcc-supply = <®_vdd_1v8>; + }; +}; + +&gpio2 { + gpio-line-names = "", "", "", "", "", + "", "", "", "", "", + "", "", "", "", "", + "", "RGMII2_nINT", "GPIO4", "RTC_INT", "", + "LVDS1_BL_EN"; +}; + +&lpi2c1 { + temperature-sensor@4f { + compatible = "nxp,p3t1755"; + reg = <0x4f>; + vs-supply = <®_vdd_1v8>; + }; +}; + +&lpi2c3 { + status = "okay"; + + leds@62 { + compatible = "nxp,pca9533"; + reg = <0x62>; + + led-1 { + type = <PCA9532_TYPE_LED>; + }; + + led-2 { + type = <PCA9532_TYPE_LED>; + }; + + led-3 { + type = <PCA9532_TYPE_LED>; + }; + }; +}; + +&lpi2c4 { + status = "okay"; + + gpio_expander: gpio@20 { + compatible = "ti,tca6416"; + reg = <0x20>; + interrupt-parent = <&gpio2>; + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; + #gpio-cells = <2>; + gpio-controller; + gpio-line-names = "CSI1_CTRL1", "CSI1_CTRL2", "CSI1_CTRL3", + "CSI1_CTRL4", "CSI2_CTRL1", "CSI2_CTRL2", + "CSI2_CTRL3", "CSI2_CTRL4", "CLK_EN_AV", + "nCAN2_EN", "nCAN1_EN", "PCIE1_nWAKE", + "PCIE2_nWAKE", "PCIE2_nALERT_3V3", + "UART1_BT_RS_SEL", "UART1_RS232_485_SEL"; + vcc-supply = <®_vdd_1v8>; + + uart1_bt_rs_sel: bt-rs-hog { + gpios = <14 GPIO_ACTIVE_HIGH>; + gpio-hog; + line-name = "UART1_BT_RS_SEL"; + output-low; + }; + }; +}; + +&lpi2c5 { + status = "okay"; + + eeprom@51 { + compatible = "atmel,24c02"; + reg = <0x51>; + pagesize = <16>; + vcc-supply = <®_vdd_1v8>; + }; +}; + +/* Used for M33 debug */ +&lpuart2 { + pinctrl-0 = <&pinctrl_lpuart2>; + pinctrl-names = "default"; +}; + +/* A-55 debug UART */ +&lpuart7 { + status = "okay"; +}; + +/* RS232/RS485/BT */ +&lpuart8 { + uart-has-rtscts; + status = "okay"; +}; + +&netc_emdio { /* RGMII2 */ + ethphy0: ethernet-phy@1 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x1>; + interrupt-parent = <&gpio2>; + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; + enet-phy-lane-no-swap; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_50_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + }; + + ethphy2: ethernet-phy@8 { + compatible = "ethernet-phy-ieee802.3-c45"; + reg = <0x8>; + max-speed = <10000>; /* 10Gbit/s */ + status = "disabled"; + }; +}; + +&pcie0 { + reset-gpio = <&gpio1 10 GPIO_ACTIVE_LOW>; + vpcie-supply = <®_vdd_3v3>; + status = "okay"; +}; + +&pcie1 { + reset-gpio = <&gpio1 14 GPIO_ACTIVE_LOW>; + vpcie-supply = <®_vdd_3v3>; + status = "okay"; +}; + +&rv3028 { + pinctrl-names = "default"; + pinctrl-0 = <&pinctrl_rtc>; + interrupt-parent = <&gpio2>; + interrupts = <18 IRQ_TYPE_LEVEL_LOW>; + aux-voltage-chargeable = <1>; + wakeup-source; + trickle-resistor-ohms = <3000>; +}; + +&scmi_iomuxc { + pinctrl_lpuart2: lpuart2grp { /* FPSC proprietary */ + fsl,pins = < + IMX95_PAD_UART2_TXD__AONMIX_TOP_LPUART2_TX 0x31e + IMX95_PAD_UART2_RXD__AONMIX_TOP_LPUART2_RX 0x31e + >; + }; + + pinctrl_lvds0: lvds0grp { + fsl,pins = < + IMX95_PAD_GPIO_IO20__GPIO2_IO_BIT20 0x31e + >; + }; + + pinctrl_rtc: rtcgrp { + fsl,pins = < + IMX95_PAD_GPIO_IO18__GPIO2_IO_BIT18 0x31e + >; + }; + + pinctrl_tpm4: tpm4grp { + fsl,pins = < + IMX95_PAD_GPIO_IO21__TPM4_CH1 0x51e + >; + }; +}; + +&tpm4 { + pinctrl-0 = <&pinctrl_tpm4>; + pinctrl-names = "default"; +}; + +&usb3 { + fsl,over-current-active-low; + fsl,power-active-low; + status = "okay"; +}; + +&usb3_dwc3 { + dr_mode = "peripheral"; + status = "okay"; +}; + +&usb3_phy { + vbus-supply = <®_vdd_5v0>; + status = "okay"; +}; + +/* uSD Card */ +&usdhc2 { + status = "okay"; +}; diff --git a/arch/arm64/boot/dts/freescale/imx95-phycore-fpsc.dtsi b/arch/arm64/boot/dts/freescale/imx95-phycore-fpsc.dtsi new file mode 100644 index 0000000000000000000000000000000000000000..7519d5bd06ba800807aaba5495b317cb54632b6c --- /dev/null +++ b/arch/arm64/boot/dts/freescale/imx95-phycore-fpsc.dtsi @@ -0,0 +1,656 @@ +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) +/* + * Copyright 2025 PHYTEC Messtechnik GmbH + */ + +#include <dt-bindings/net/ti-dp83867.h> +#include "imx95.dtsi" + +/ { + model = "PHYTEC phyCORE-i.MX95 FPSC"; + compatible = "phytec,imx95-phycore-fpsc", "fsl,imx95"; + + aliases { + ethernet1 = &enetc_port1; + i2c1 = &lpi2c2; + i2c2 = &lpi2c5; + i2c3 = &lpi2c3; + i2c4 = &lpi2c4; + i2c5 = &lpi2c1; + rtc0 = &rv3028; + rtc1 = &scmi_bbm; + }; + + memory@80000000 { + device_type = "memory"; + reg = <0x00000000 0x80000000 0x00000001 0x00000000>; + }; + + reg_nvcc_aon: regulator-nvcc-aon { + compatible = "regulator-fixed"; + regulator-always-on; + regulator-boot-on; + regulator-max-microvolt = <1800000>; + regulator-min-microvolt = <1800000>; + regulator-name = "VDD_IO"; + }; + + reg_usdhc2_vmmc: regulator-usdhc2 { + compatible = "regulator-fixed"; + off-on-delay-us = <12000>; + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; + pinctrl-names = "default"; + regulator-max-microvolt = <3300000>; + regulator-min-microvolt = <3300000>; + regulator-name = "VDDSW_SD2"; + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; + enable-active-high; + }; + + reserved-memory { + ranges; + #address-cells = <2>; + #size-cells = <2>; + + linux,cma { + compatible = "shared-dma-pool"; + alloc-ranges = <0 0x80000000 0 0x7f000000>; + reusable; + size = <0 0x3c000000>; + linux,cma-default; + }; + }; +}; + +&enetc_port0 { /* FPSC RGMII2 */ + phy-mode = "rgmii-id"; + pinctrl-0 = <&pinctrl_enetc0>; + pinctrl-names = "default"; +}; + +&enetc_port1 { + phy-handle = <ðphy1>; + phy-mode = "rgmii-id"; + pinctrl-0 = <&pinctrl_enetc1>; + pinctrl-names = "default"; + status = "okay"; +}; + +&flexcan1 { /* FPSC CAN1 */ + pinctrl-0 = <&pinctrl_flexcan1>; + pinctrl-names = "default"; +}; + +&flexcan2 { /* FPSC CAN2 */ + pinctrl-0 = <&pinctrl_flexcan2>; + pinctrl-names = "default"; +}; + +&flexspi1 { /* FPSC QSPI */ + pinctrl-0 = <&pinctrl_flexspi>; + pinctrl-names = "default"; +}; + +&gpio1 { /* FPSC GPIO */ + gpio-line-names = "", "", "", "", "GPIO2", + "GPIO1", "", "", "", "", + "PCIE1_nPERST", "USB1_PWR_EN", "GPIO3", "USB2_PWR_EN", "PCIE2_nPERST"; + pinctrl-0 = <&pinctrl_gpio1>; + pinctrl-names = "default"; + status = "okay"; +}; + +&gpio2 { /* FPSC GPIO */ + gpio-line-names = "", "", "", "", "", + "", "", "", "", "", + "", "", "", "", "", + "", "RGMII2_nINT", "GPIO4"; + pinctrl-0 = <&pinctrl_gpio2>; + pinctrl-names = "default"; +}; + +&gpio3 { + gpio-line-names = "", "", "", "", "", + "", "", "SD2_RESET_B"; +}; + +&gpio4 { + gpio-line-names = "ENET2_nINT"; +}; + +&gpio5 { + gpio-line-names = "", "", "", "", "", + "", "", "", "", "", + "", "", "", "USB1_OC", "USB2_OC"; +}; + +&lpi2c1 { /* FPSC I2C5 */ + clock-frequency = <400000>; + pinctrl-0 = <&pinctrl_lpi2c1>; + pinctrl-names = "default"; + status = "okay"; + + dram_sense: temperature-sensor@48 { + compatible = "ti,tmp102"; + reg = <0x48>; + #thermal-sensor-cells = <1>; + }; + + emmc_sense: temperature-sensor@49 { + compatible = "ti,tmp102"; + reg = <0x49>; + #thermal-sensor-cells = <1>; + }; + + ethphy_sense: temperature-sensor@4a { + compatible = "ti,tmp102"; + reg = <0x4a>; + #thermal-sensor-cells = <1>; + }; + + pmic_sense: temperature-sensor@4b { + compatible = "ti,tmp102"; + reg = <0x4b>; + #thermal-sensor-cells = <1>; + }; + + /* User EEPROM */ + eeprom@50 { + compatible = "st,24c32", "atmel,24c32"; + reg = <0x50>; + pagesize = <32>; + vcc-supply = <®_nvcc_aon>; + }; + + /* Factory EEPROM */ + eeprom@51 { + compatible = "st,24c32", "atmel,24c32"; + reg = <0x51>; + pagesize = <32>; + vcc-supply = <®_nvcc_aon>; + }; + + rv3028: rtc@52 { + compatible = "microcrystal,rv3028"; + reg = <0x52>; + }; + + /* User EEPROM ID page */ + eeprom@58 { + compatible = "st,24c32", "atmel,24c32"; + reg = <0x58>; + pagesize = <32>; + vcc-supply = <®_nvcc_aon>; + }; +}; + +&lpi2c2 { /* FPSC I2C1 */ + clock-frequency = <400000>; + pinctrl-0 = <&pinctrl_lpi2c2>; + pinctrl-names = "default"; +}; + +&lpi2c3 { /* FPSC I2C3 */ + clock-frequency = <400000>; + pinctrl-0 = <&pinctrl_lpi2c3>; + pinctrl-names = "default"; +}; + +&lpi2c4 { /* FPSC I2C4 */ + clock-frequency = <400000>; + pinctrl-0 = <&pinctrl_lpi2c4>; + pinctrl-names = "default"; +}; + +&lpi2c5 { /* FPSC I2C2 */ + clock-frequency = <400000>; + pinctrl-0 = <&pinctrl_lpi2c5>; + pinctrl-names = "default"; +}; + +&lpspi3 { /* FPSC SPI2 */ + pinctrl-0 = <&pinctrl_lpspi3>; + pinctrl-names = "default"; +}; + +&lpspi4 { /* FPSC SPI3 */ + pinctrl-0 = <&pinctrl_lpspi4>; + pinctrl-names = "default"; +}; + +&lpspi7 { /* FPSC SPI1 */ + pinctrl-0 = <&pinctrl_lpspi7>; + pinctrl-names = "default"; +}; + +&lpuart5 { /* FPSC UART2 */ + pinctrl-0 = <&pinctrl_lpuart5>; + pinctrl-names = "default"; +}; + +&lpuart7 { /* FPSC UART3 */ + pinctrl-0 = <&pinctrl_lpuart7>; + pinctrl-names = "default"; +}; + +&lpuart8 { /* FPSC UART1 */ + pinctrl-0 = <&pinctrl_lpuart8>; + pinctrl-names = "default"; +}; + +&netc_blk_ctrl { + status = "okay"; +}; + +&netc_emdio { /* FPSC RGMII2 */ + pinctrl-0 = <&pinctrl_emdio>; + pinctrl-names = "default"; + status = "okay"; + + ethphy1: ethernet-phy@0 { + compatible = "ethernet-phy-ieee802.3-c22"; + reg = <0x0>; + interrupt-parent = <&gpio4>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + enet-phy-lane-no-swap; + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; + }; +}; + +&netcmix_blk_ctrl { + status = "okay"; +}; + +&pcie0 { /* FPSC PCIE1 */ + pinctrl-0 = <&pinctrl_pcie0>; + pinctrl-names = "default"; +}; + +&pcie1 { /* FPSC PCIE2 */ + pinctrl-0 = <&pinctrl_pcie1>; + pinctrl-names = "default"; +}; + +&sai5 { /* FPSC SAI1 */ + pinctrl-0 = <&pinctrl_sai5>; + pintrc-names = "default"; +}; + +&scmi_iomuxc { + pinctrl_emdio: emdiogrp { + fsl,pins = < + IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_NETC_MDIO 0x97e /* RGMII2_MDIO */ + IMX95_PAD_ENET2_MDC__NETCMIX_TOP_NETC_MDC 0x502 /* RGMII2_MDC */ + >; + }; + + pinctrl_enetc0: enetc0grp { + fsl,pins = < + IMX95_PAD_GPIO_IO16__GPIO2_IO_BIT16 0x31e /* RGMII2_nINT */ + IMX95_PAD_CCM_CLKO3__NETCMIX_TOP_NETC_TMR_1588_TRIG2 0x31e /* RGMII2_EVENT_IN */ + IMX95_PAD_CCM_CLKO4__NETCMIX_TOP_NETC_TMR_1588_PP2 0x31e /* RGMII2_EVENT_OUT */ + + IMX95_PAD_ENET1_TD3__NETCMIX_TOP_ETH0_RGMII_TD3 0x57e /* RGMII2_TX_3 */ + IMX95_PAD_ENET1_TD2__NETCMIX_TOP_ETH0_RGMII_TD2 0x57e /* RGMII2_TX_2 */ + IMX95_PAD_ENET1_TD1__NETCMIX_TOP_ETH0_RGMII_TD1 0x57e /* RGMII2_TX_1 */ + IMX95_PAD_ENET1_TD0__NETCMIX_TOP_ETH0_RGMII_TD0 0x57e /* RGMII2_TX_0 */ + IMX95_PAD_ENET1_TX_CTL__NETCMIX_TOP_ETH0_RGMII_TX_CTL 0x57e /* RGMII2_TX_CTL */ + IMX95_PAD_ENET1_TXC__NETCMIX_TOP_ETH0_RGMII_TX_CLK 0x58e /* RGMII2_TXC */ + IMX95_PAD_ENET1_RD3__NETCMIX_TOP_ETH0_RGMII_RD3 0x57e /* RGMII2_RX_3 */ + IMX95_PAD_ENET1_RD2__NETCMIX_TOP_ETH0_RGMII_RD2 0x57e /* RGMII2_RX_2 */ + IMX95_PAD_ENET1_RD1__NETCMIX_TOP_ETH0_RGMII_RD1 0x57e /* RGMII2_RX_1 */ + IMX95_PAD_ENET1_RD0__NETCMIX_TOP_ETH0_RGMII_RD0 0x57e /* RGMII2_RX_0 */ + IMX95_PAD_ENET1_RX_CTL__NETCMIX_TOP_ETH0_RGMII_RX_CTL 0x57e /* RGMII2_RX_CTL */ + IMX95_PAD_ENET1_RXC__NETCMIX_TOP_ETH0_RGMII_RX_CLK 0x58e /* RGMII2_RXC */ + >; + }; + + pinctrl_enetc1: enetc1grp { + fsl,pins = < + IMX95_PAD_ENET1_MDC__GPIO4_IO_BIT0 0x31e + IMX95_PAD_ENET2_TD0__NETCMIX_TOP_ETH1_RGMII_TD0 0x57e + IMX95_PAD_ENET2_TD1__NETCMIX_TOP_ETH1_RGMII_TD1 0x57e + IMX95_PAD_ENET2_TD2__NETCMIX_TOP_ETH1_RGMII_TD2 0x57e + IMX95_PAD_ENET2_TD3__NETCMIX_TOP_ETH1_RGMII_TD3 0x57e + IMX95_PAD_ENET2_TX_CTL__NETCMIX_TOP_ETH1_RGMII_TX_CTL 0x57e + IMX95_PAD_ENET2_TXC__NETCMIX_TOP_ETH1_RGMII_TX_CLK 0x58e + IMX95_PAD_ENET2_RD0__NETCMIX_TOP_ETH1_RGMII_RD0 0x57e + IMX95_PAD_ENET2_RD1__NETCMIX_TOP_ETH1_RGMII_RD1 0x57e + IMX95_PAD_ENET2_RD2__NETCMIX_TOP_ETH1_RGMII_RD2 0x57e + IMX95_PAD_ENET2_RD3__NETCMIX_TOP_ETH1_RGMII_RD3 0x57e + IMX95_PAD_ENET2_RX_CTL__NETCMIX_TOP_ETH1_RGMII_RX_CTL 0x57e + IMX95_PAD_ENET2_RXC__NETCMIX_TOP_ETH1_RGMII_RX_CLK 0x58e + >; + }; + + pinctrl_flexcan1: flexcan1grp { + fsl,pins = < + IMX95_PAD_PDM_CLK__AONMIX_TOP_CAN1_TX 0x51e /* CAN1_TX */ + IMX95_PAD_PDM_BIT_STREAM0__AONMIX_TOP_CAN1_RX 0x51e /* CAN1_RX */ + >; + }; + + pinctrl_flexcan2: flexcan2grp { + fsl,pins = < + IMX95_PAD_GPIO_IO25__CAN2_TX 0x51e /* CAN2_TX */ + IMX95_PAD_GPIO_IO27__CAN2_RX 0x51e /* CAN2_RX */ + >; + }; + + pinctrl_flexspi: flexspigrp { + fsl,pins = < + IMX95_PAD_XSPI1_SS0_B__FLEXSPI1_A_SS0_B 0x3fe /* QSPI_CE */ + IMX95_PAD_XSPI1_SCLK__FLEXSPI1_A_SCLK 0x3fe /* QSPI_CLK */ + IMX95_PAD_XSPI1_DATA0__FLEXSPI1_A_DATA_BIT0 0x3fe /* QSPI_DATA_0 */ + IMX95_PAD_XSPI1_DATA1__FLEXSPI1_A_DATA_BIT1 0x3fe /* QSPI_DATA_1 */ + IMX95_PAD_XSPI1_DATA2__FLEXSPI1_A_DATA_BIT2 0x3fe /* QSPI_DATA_2 */ + IMX95_PAD_XSPI1_DATA3__FLEXSPI1_A_DATA_BIT3 0x3fe /* QSPI_DATA_3 */ + IMX95_PAD_XSPI1_DQS__FLEXSPI1_A_DQS 0x3fe /* QSPI_DQS */ + >; + }; + + pinctrl_gpio1: gpio1grp { + fsl,pins = < + IMX95_PAD_UART1_TXD__AONMIX_TOP_GPIO1_IO_BIT5 0x31e /* GPIO1 */ + IMX95_PAD_UART1_RXD__AONMIX_TOP_GPIO1_IO_BIT4 0x31e /* GPIO2 */ + IMX95_PAD_SAI1_TXC__AONMIX_TOP_GPIO1_IO_BIT12 0x31e /* GPIO3 */ + >; + }; + + pinctrl_gpio2: gpio2grp { + fsl,pins = < + IMX95_PAD_GPIO_IO17__GPIO2_IO_BIT17 0x31e /* GPIO4 */ + >; + }; + + pinctrl_lpi2c1: lpi2c1grp { + fsl,pins = < + IMX95_PAD_I2C1_SCL__AONMIX_TOP_LPI2C1_SCL 0x40000b9e /* I2C5_SCL */ + IMX95_PAD_I2C1_SDA__AONMIX_TOP_LPI2C1_SDA 0x40000b9e /* I2C5_SDA */ + >; + }; + + pinctrl_lpi2c2: lpi2c2grp { + fsl,pins = < + IMX95_PAD_I2C2_SDA__AONMIX_TOP_LPI2C2_SDA 0x40000b9e /* I2C1_SDA_DNU */ + IMX95_PAD_I2C2_SCL__AONMIX_TOP_LPI2C2_SCL 0x40000b9e /* I2C1_SCL_DNU */ + >; + }; + + pinctrl_lpi2c3: lpi2c3grp { + fsl,pins = < + IMX95_PAD_GPIO_IO28__LPI2C3_SDA 0x40000b9e /* I2C3_SDA */ + IMX95_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e /* I2C3_SCL */ + >; + }; + + pinctrl_lpi2c4: lpi2c4grp { + fsl,pins = < + IMX95_PAD_GPIO_IO30__LPI2C4_SDA 0x40000b9e /* I2C4_SDA */ + IMX95_PAD_GPIO_IO31__LPI2C4_SCL 0x40000b9e /* I2C4_SDL */ + >; + }; + + pinctrl_lpi2c5: lpi2c5grp { + fsl,pins = < + IMX95_PAD_GPIO_IO22__LPI2C5_SDA 0x40000b9e /* I2C2_SDA */ + IMX95_PAD_GPIO_IO23__LPI2C5_SCL 0x40000b9e /* I2C2_SCL */ + >; + }; + + pinctrl_lpspi3: lpspi3grp { + fsl,pins = < + IMX95_PAD_GPIO_IO11__LPSPI3_SCK 0x51e /* SPI2_SCLK */ + IMX95_PAD_GPIO_IO10__LPSPI3_SOUT 0x51e /* SPI2_MOSI */ + IMX95_PAD_GPIO_IO09__LPSPI3_SIN 0x51e /* SPI2_MISO */ + IMX95_PAD_GPIO_IO08__LPSPI3_PCS0 0x51e /* SPI2_CS */ + >; + }; + + pinctrl_lpspi4: lpspi4grp { + fsl,pins = < + IMX95_PAD_GPIO_IO21__LPSPI4_SCK 0x51e /* SPI3_SCLK */ + IMX95_PAD_GPIO_IO20__LPSPI4_SOUT 0x51e /* SPI3_MOSI */ + IMX95_PAD_GPIO_IO19__LPSPI4_SIN 0x51e /* SPI3_MISO */ + IMX95_PAD_GPIO_IO18__LPSPI4_PCS0 0x51e /* SPI3_CS */ + >; + }; + + pinctrl_lpspi7: lpspi7grp { + fsl,pins = < + IMX95_PAD_GPIO_IO07__LPSPI7_SCK 0x51e /* SPI1_SCLK */ + IMX95_PAD_GPIO_IO06__LPSPI7_SOUT 0x51e /* SPI1_MOSI */ + IMX95_PAD_GPIO_IO05__LPSPI7_SIN 0x51e /* SPI1_MISO */ + IMX95_PAD_GPIO_IO04__LPSPI7_PCS0 0x51e /* SPI1_CS */ + >; + }; + + pinctrl_lpuart5: lpuart5grp { + fsl,pins = < + IMX95_PAD_GPIO_IO01__LPUART5_RX 0x51e /* UART2_RXD */ + IMX95_PAD_GPIO_IO00__LPUART5_TX 0x51e /* UART2_TXD */ + IMX95_PAD_GPIO_IO03__LPUART5_RTS_B 0x51e /* UART2_RTS */ + IMX95_PAD_GPIO_IO02__LPUART5_CTS_B 0x51e /* UART2_CTS */ + >; + }; + + pinctrl_lpuart7: lpuart7grp { + fsl,pins = < + IMX95_PAD_GPIO_IO37__LPUART7_RX 0x31e /* UART3_RXD */ + IMX95_PAD_GPIO_IO36__LPUART7_TX 0x31e /* UART3_TXD */ + >; + }; + + pinctrl_lpuart8: lpuart8grp { + fsl,pins = < + IMX95_PAD_GPIO_IO13__LPUART8_RX 0x51e /* UART1_RXD */ + IMX95_PAD_GPIO_IO12__LPUART8_TX 0x51e /* UART1_TXD */ + IMX95_PAD_GPIO_IO15__LPUART8_RTS_B 0x51e /* UART1_RTS */ + IMX95_PAD_GPIO_IO14__LPUART8_CTS_B 0x51e /* UART1_CTS */ + >; + }; + + pinctrl_pcie0: pcie0grp { + fsl,pins = < + IMX95_PAD_GPIO_IO32__HSIOMIX_TOP_PCIE1_CLKREQ_B 0x31e /* PCIE1_nCLKREQ */ + IMX95_PAD_PDM_BIT_STREAM1__AONMIX_TOP_GPIO1_IO_BIT10 0x31e /* PCIE1_nPERST */ + >; + }; + + pinctrl_pcie1: pcie1grp { + fsl,pins = < + IMX95_PAD_GPIO_IO35__HSIOMIX_TOP_PCIE2_CLKREQ_B 0x31e /* PCIE2_nCLKREQ */ + IMX95_PAD_SAI1_RXD0__AONMIX_TOP_GPIO1_IO_BIT14 0x31e /* PCIE2_nPERST */ + >; + }; + + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { + fsl,pins = < + IMX95_PAD_SD2_RESET_B__GPIO3_IO_BIT7 0x31e + >; + }; + + pinctrl_sai5: sai5grp { + fsl,pins = < + IMX95_PAD_XSPI1_DQS__SAI5_RX_SYNC 0x51e /* SAI1_RX_SYNC */ + IMX95_PAD_XSPI1_SS1_B__SAI5_RX_BCLK 0x51e /* SAI1_RX_BCLK */ + IMX95_PAD_XSPI1_DATA7__SAI5_RX_DATA_BIT0 0x51e /* SAI1_RX_DATA */ + IMX95_PAD_XSPI1_DATA5__SAI5_TX_SYNC 0x51e /* SAI1_TX_SYNC */ + IMX95_PAD_XSPI1_DATA6__SAI5_TX_BCLK 0x51e /* SAI1_TX_BCLK */ + IMX95_PAD_XSPI1_DATA4__SAI5_TX_DATA_BIT0 0x51e /* SAI1_TX_DATA */ + >; + }; + + pinctrl_tpm3: tpm3grp { + fsl,pins = < + IMX95_PAD_GPIO_IO24__TPM3_CH3 0x51e /* PWM1 */ + >; + }; + + pinctrl_tpm5: tpm5grp { + fsl,pins = < + IMX95_PAD_GPIO_IO26__TPM5_CH3 0x51e /* PWM2 */ + >; + }; + + pinctrl_usbc: usbcgrp { + fsl,pins = < + IMX95_PAD_SAI1_TXFS__AONMIX_TOP_GPIO1_IO_BIT11 0x51e /* USB1_PWR_EN */ + IMX95_PAD_GPIO_IO33__GPIO5_IO_BIT13 0x51e /* USB1_OC */ + >; + }; + + pinctrl_usb2: usb2grp { + fsl,pins = < + IMX95_PAD_SAI1_TXD0__AONMIX_TOP_GPIO1_IO_BIT13 0x51e /* USB2_PWR_EN */ + IMX95_PAD_GPIO_IO34__GPIO5_IO_BIT14 0x51e /* USB2_OC */ + >; + }; + + pinctrl_usdhc1: usdhc1grp { + fsl,pins = < + IMX95_PAD_SD1_DATA0__USDHC1_DATA0 0x138e + IMX95_PAD_SD1_DATA1__USDHC1_DATA1 0x138e + IMX95_PAD_SD1_DATA2__USDHC1_DATA2 0x138e + IMX95_PAD_SD1_DATA3__USDHC1_DATA3 0x138e + IMX95_PAD_SD1_DATA4__USDHC1_DATA4 0x138e + IMX95_PAD_SD1_DATA5__USDHC1_DATA5 0x138e + IMX95_PAD_SD1_DATA6__USDHC1_DATA6 0x138e + IMX95_PAD_SD1_DATA7__USDHC1_DATA7 0x138e + IMX95_PAD_SD1_CMD__USDHC1_CMD 0x138e + IMX95_PAD_SD1_CLK__USDHC1_CLK 0x158e + IMX95_PAD_SD1_STROBE__USDHC1_STROBE 0x158e + >; + }; + + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { + fsl,pins = < + IMX95_PAD_SD1_DATA0__USDHC1_DATA0 0x138e + IMX95_PAD_SD1_DATA1__USDHC1_DATA1 0x138e + IMX95_PAD_SD1_DATA2__USDHC1_DATA2 0x138e + IMX95_PAD_SD1_DATA3__USDHC1_DATA3 0x138e + IMX95_PAD_SD1_DATA4__USDHC1_DATA4 0x138e + IMX95_PAD_SD1_DATA5__USDHC1_DATA5 0x138e + IMX95_PAD_SD1_DATA6__USDHC1_DATA6 0x138e + IMX95_PAD_SD1_DATA7__USDHC1_DATA7 0x138e + IMX95_PAD_SD1_CMD__USDHC1_CMD 0x138e + IMX95_PAD_SD1_CLK__USDHC1_CLK 0x158e + IMX95_PAD_SD1_STROBE__USDHC1_STROBE 0x158e + >; + }; + + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { + fsl,pins = < + IMX95_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe + IMX95_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe + IMX95_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe + IMX95_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe + IMX95_PAD_SD1_DATA4__USDHC1_DATA4 0x13fe + IMX95_PAD_SD1_DATA5__USDHC1_DATA5 0x13fe + IMX95_PAD_SD1_DATA6__USDHC1_DATA6 0x13fe + IMX95_PAD_SD1_DATA7__USDHC1_DATA7 0x13fe + IMX95_PAD_SD1_CMD__USDHC1_CMD 0x13fe + IMX95_PAD_SD1_CLK__USDHC1_CLK 0x15fe + IMX95_PAD_SD1_STROBE__USDHC1_STROBE 0x15fe + >; + }; + + pinctrl_usdhc2: usdhc2grp { + fsl,pins = < + IMX95_PAD_SD2_CD_B__USDHC2_CD_B 0x31e /* CD */ + IMX95_PAD_SD2_CLK__USDHC2_CLK 0x158e /* CLK */ + IMX95_PAD_SD2_CMD__USDHC2_CMD 0x138e /* CMD */ + IMX95_PAD_SD2_DATA0__USDHC2_DATA0 0x138e /* DATA0 */ + IMX95_PAD_SD2_DATA1__USDHC2_DATA1 0x138e /* DATA1 */ + IMX95_PAD_SD2_DATA2__USDHC2_DATA2 0x138e /* DATA2 */ + IMX95_PAD_SD2_DATA3__USDHC2_DATA3 0x138e /* DATA3 */ + IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e + + >; + }; + + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { + fsl,pins = < + IMX95_PAD_SD2_CD_B__USDHC2_CD_B 0x31e /* CD */ + IMX95_PAD_SD2_CLK__USDHC2_CLK 0x158e /* CLK */ + IMX95_PAD_SD2_CMD__USDHC2_CMD 0x138e /* CMD */ + IMX95_PAD_SD2_DATA0__USDHC2_DATA0 0x138e /* DATA0 */ + IMX95_PAD_SD2_DATA1__USDHC2_DATA1 0x138e /* DATA1 */ + IMX95_PAD_SD2_DATA2__USDHC2_DATA2 0x138e /* DATA2 */ + IMX95_PAD_SD2_DATA3__USDHC2_DATA3 0x138e /* DATA3 */ + IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e + >; + }; + + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { + fsl,pins = < + IMX95_PAD_SD2_CD_B__USDHC2_CD_B 0x31e /* CD */ + IMX95_PAD_SD2_CLK__USDHC2_CLK 0x15fe /* CLK */ + IMX95_PAD_SD2_CMD__USDHC2_CMD 0x13fe /* CMD */ + IMX95_PAD_SD2_DATA0__USDHC2_DATA0 0x13fe /* DATA0 */ + IMX95_PAD_SD2_DATA1__USDHC2_DATA1 0x13fe /* DATA1 */ + IMX95_PAD_SD2_DATA2__USDHC2_DATA2 0x13fe /* DATA2 */ + IMX95_PAD_SD2_DATA3__USDHC2_DATA3 0x13fe /* DATA3 */ + IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e + >; + }; + + pinctrl_usdhc3: usdhc3grp { + fsl,pins = < + IMX95_PAD_SD3_CLK__USDHC3_CLK 0x158e /* SDIO_CLK */ + IMX95_PAD_SD3_CMD__USDHC3_CMD 0x138e /* SDIO_CMD */ + IMX95_PAD_SD3_DATA0__USDHC3_DATA0 0x138e /* SDIO_DATA0 */ + IMX95_PAD_SD3_DATA1__USDHC3_DATA1 0x138e /* SDIO_DATA1 */ + IMX95_PAD_SD3_DATA2__USDHC3_DATA2 0x138e /* SDIO_DATA2 */ + IMX95_PAD_SD3_DATA3__USDHC3_DATA3 0x138e /* SDIO_DATA3 */ + >; + }; +}; + +&tpm3 { /* FPSC PWM1 */ + pinctrl-0 = <&pinctrl_tpm3>; + pinctrl-names = "default"; +}; + +&tpm5 { /* FPSC PWM2 */ + pinctrl-0 = <&pinctrl_tpm5>; + pinctrl-names = "default"; +}; + +&usb3 { /* FPSC USB1 */ + pinctrl-0 = <&pinctrl_usbc>; + pinctrl-names = "default"; +}; + +&usdhc1 { + bus-width = <8>; + non-removable; + no-sd; + no-sdio; + pinctrl-0 = <&pinctrl_usdhc1>; + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; + pinctrl-3 = <&pinctrl_usdhc1>; + pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; + status = "okay"; +}; + +&usdhc2 { /* FPSC SDCARD */ + bus-width = <4>; + disable-wp; + pinctrl-0 = <&pinctrl_usdhc2>; + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; + pinctrl-3 = <&pinctrl_usdhc2>; + pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; + sd-uhs-sdr104; + vmmc-supply = <®_usdhc2_vmmc>; +}; + +&usdhc3 { /* FPSC SDIO */ + pinctrl-0 = <&pinctrl_usdhc3>; + pinctrl-names = "default"; +}; -- 2.43.0 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* Re: [PATCH v3 2/2] arm64: dts: add imx95-libra-rdk-fpsc board 2025-06-11 13:05 ` [PATCH v3 2/2] arm64: dts: add imx95-libra-rdk-fpsc board Yannic Moog @ 2025-06-11 16:41 ` Frank Li 0 siblings, 0 replies; 7+ messages in thread From: Frank Li @ 2025-06-11 16:41 UTC (permalink / raw) To: Yannic Moog Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, upstream, Benjamin Hahn, Teresa Remmet, Yashwanth Varakala, Jan Remmet, devicetree, linux-kernel, imx, linux-arm-kernel On Wed, Jun 11, 2025 at 03:05:31PM +0200, Yannic Moog wrote: > Add device tree for the Libra-i.MX 95 FPSC board. The Libra is a > pure development board and has hardware to support FPSC-24-A.0 set of > features. The phyCORE-i.MX 95 FPSC [1] SoM uses only a subset of > the hardware features of the Libra board. The phyCORE-i.MX 95 FPSC > itself is a System on Module designed around the i.MX 95 SoC. > The SoM and board utilize the Future Proof Solder Core [2] BGA standard > to connect to each other. > > To be able to easily map FPSC interface names to SoC interfaces, the > FPSC interface names are added as inline comments. Example: > > &lpi2c5 { /* I2C2 */ > pinctrl-0 = <&pinctrl_lpi2c5>; > [...] > }; > > Here, I2C2 is the FPSC interface name. The lpi2c5 instance of the i.MX 95 > SoC is used to fulfill the i2c functionality and its signals are routed > to the FPSC I2C2 signal pins: > > pinctrl_lpi2c5: lpi2c5grp { > fsl,pins = < > IMX95_PAD_GPIO_IO22__LPI2C5_SDA 0x40000b9e /* I2C2_SDA */ > IMX95_PAD_GPIO_IO23__LPI2C5_SCL 0x40000b9e /* I2C2_SCL */ > >; > }; > > [1] https://www.phytec.eu/en/produkte/system-on-modules/phycore-imx-95-fpsc/ > [2] https://www.phytec.eu/en/produkte/system-on-modules/fpsc/ > > Signed-off-by: Yannic Moog <y.moog@phytec.de> > --- Reviewed-by: Frank Li <Frank.Li@nxp.com> > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../boot/dts/freescale/imx95-libra-rdk-fpsc.dts | 318 ++++++++++ > .../boot/dts/freescale/imx95-phycore-fpsc.dtsi | 656 +++++++++++++++++++++ > 3 files changed, 975 insertions(+) > > diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile > index 0b473a23d12008ff79d6467d9e1c7ab2c4d6a9a6..656a7ec547b20c4fd3d8f4c54ba149c13b57b386 100644 > --- a/arch/arm64/boot/dts/freescale/Makefile > +++ b/arch/arm64/boot/dts/freescale/Makefile > @@ -339,6 +339,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx95-15x15-evk-pcie0-ep.dtb > imx95-19x19-evk-pcie0-ep-dtbs += imx95-19x19-evk.dtb imx-pcie0-ep.dtbo > imx95-19x19-evk-pcie1-ep-dtbs += imx95-19x19-evk.dtb imx-pcie1-ep.dtbo > dtb-$(CONFIG_ARCH_MXC) += imx95-19x19-evk-pcie0-ep.dtb imx95-19x19-evk-pcie1-ep.dtb > +dtb-$(CONFIG_ARCH_MXC) += imx95-libra-rdk-fpsc.dtb > > imx8mm-kontron-dl-dtbs := imx8mm-kontron-bl.dtb imx8mm-kontron-dl.dtbo > > diff --git a/arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dts b/arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dts > new file mode 100644 > index 0000000000000000000000000000000000000000..26c2df9b1b60a89fbd8456db6aec8c8d72abbd3e > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dts > @@ -0,0 +1,318 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2025 PHYTEC Messtechnik GmbH > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/leds/leds-pca9532.h> > +#include <dt-bindings/pwm/pwm.h> > + > +#include "imx95-phycore-fpsc.dtsi" > + > +/ { > + compatible = "phytec,imx95-libra-rdk-fpsc", > + "phytec,imx95-phycore-fpsc", "fsl,imx95"; > + model = "PHYTEC Libra i.MX95 RDK FPSC"; > + > + aliases { > + can1 = &flexcan2; > + can2 = &flexcan1; > + ethernet0 = &enetc_port0; > + serial0 = &lpuart7; > + serial1 = &lpuart8; > + }; > + > + chosen { > + stdout-path = &lpuart7; > + }; > + > + backlight_lvds0: backlight0 { > + compatible = "pwm-backlight"; > + pinctrl-0 = <&pinctrl_lvds0>; > + power-supply = <®_vdd_12v0>; > + status = "disabled"; > + }; > + > + transceiver1: can-phy { > + compatible = "ti,tcan1043"; > + #phy-cells = <0>; > + max-bitrate = <8000000>; > + enable-gpios = <&gpio_expander 10 GPIO_ACTIVE_LOW>; > + }; > + > + transceiver2: can-phy { > + compatible = "ti,tcan1043"; > + #phy-cells = <0>; > + max-bitrate = <8000000>; > + enable-gpios = <&gpio_expander 9 GPIO_ACTIVE_LOW>; > + }; > + > + panel0_lvds: panel-lvds0 { > + backlight = <&backlight_lvds0>; > + power-supply = <®_vdd_3v3>; > + status = "disabled"; > + }; > + > + reg_vdd_12v0: regulator-vdd-12v0 { > + compatible = "regulator-fixed"; > + regulator-always-on; > + regulator-boot-on; > + regulator-max-microvolt = <12000000>; > + regulator-min-microvolt = <12000000>; > + regulator-name = "VDD_12V0"; > + }; > + > + reg_vdd_1v8: regulator-vdd-1v8 { > + compatible = "regulator-fixed"; > + regulator-always-on; > + regulator-boot-on; > + regulator-max-microvolt = <1800000>; > + regulator-min-microvolt = <1800000>; > + regulator-name = "VDD_1V8"; > + }; > + > + reg_vdd_3v3: regulator-vdd-3v3 { > + compatible = "regulator-fixed"; > + regulator-always-on; > + regulator-boot-on; > + regulator-max-microvolt = <3300000>; > + regulator-min-microvolt = <3300000>; > + regulator-name = "VDD_3V3"; > + }; > + > + reg_vdd_5v0: regulator-vdd-5v0 { > + compatible = "regulator-fixed"; > + regulator-always-on; > + regulator-boot-on; > + regulator-max-microvolt = <5000000>; > + regulator-min-microvolt = <5000000>; > + regulator-name = "VDD_5V0"; > + }; > +}; > + > +&enetc_port0 { > + phy-handle = <ðphy0>; > + status = "okay"; > +}; > + > +&enetc_port2 { > + managed = "in-band-status"; > + phy-handle = <ðphy2>; > + phy-mode = "10gbase-r"; > +}; > + > +/* CAN FD */ > +&flexcan1 { > + phys = <&transceiver1>; > + status = "okay"; > +}; > + > +&flexcan2 { > + phys = <&transceiver2>; > + status = "okay"; > +}; > + > +/* SPI-NOR */ > +&flexspi1 { > + pinctrl-0 = <&pinctrl_flexspi>; > + pinctrl-names = "default"; > + status = "okay"; > + > + spi_nor: flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <166000000>; > + spi-rx-bus-width = <4>; > + spi-tx-bus-width = <4>; > + vcc-supply = <®_vdd_1v8>; > + }; > +}; > + > +&gpio2 { > + gpio-line-names = "", "", "", "", "", > + "", "", "", "", "", > + "", "", "", "", "", > + "", "RGMII2_nINT", "GPIO4", "RTC_INT", "", > + "LVDS1_BL_EN"; > +}; > + > +&lpi2c1 { > + temperature-sensor@4f { > + compatible = "nxp,p3t1755"; > + reg = <0x4f>; > + vs-supply = <®_vdd_1v8>; > + }; > +}; > + > +&lpi2c3 { > + status = "okay"; > + > + leds@62 { > + compatible = "nxp,pca9533"; > + reg = <0x62>; > + > + led-1 { > + type = <PCA9532_TYPE_LED>; > + }; > + > + led-2 { > + type = <PCA9532_TYPE_LED>; > + }; > + > + led-3 { > + type = <PCA9532_TYPE_LED>; > + }; > + }; > +}; > + > +&lpi2c4 { > + status = "okay"; > + > + gpio_expander: gpio@20 { > + compatible = "ti,tca6416"; > + reg = <0x20>; > + interrupt-parent = <&gpio2>; > + interrupts = <17 IRQ_TYPE_LEVEL_LOW>; > + #gpio-cells = <2>; > + gpio-controller; > + gpio-line-names = "CSI1_CTRL1", "CSI1_CTRL2", "CSI1_CTRL3", > + "CSI1_CTRL4", "CSI2_CTRL1", "CSI2_CTRL2", > + "CSI2_CTRL3", "CSI2_CTRL4", "CLK_EN_AV", > + "nCAN2_EN", "nCAN1_EN", "PCIE1_nWAKE", > + "PCIE2_nWAKE", "PCIE2_nALERT_3V3", > + "UART1_BT_RS_SEL", "UART1_RS232_485_SEL"; > + vcc-supply = <®_vdd_1v8>; > + > + uart1_bt_rs_sel: bt-rs-hog { > + gpios = <14 GPIO_ACTIVE_HIGH>; > + gpio-hog; > + line-name = "UART1_BT_RS_SEL"; > + output-low; > + }; > + }; > +}; > + > +&lpi2c5 { > + status = "okay"; > + > + eeprom@51 { > + compatible = "atmel,24c02"; > + reg = <0x51>; > + pagesize = <16>; > + vcc-supply = <®_vdd_1v8>; > + }; > +}; > + > +/* Used for M33 debug */ > +&lpuart2 { > + pinctrl-0 = <&pinctrl_lpuart2>; > + pinctrl-names = "default"; > +}; > + > +/* A-55 debug UART */ > +&lpuart7 { > + status = "okay"; > +}; > + > +/* RS232/RS485/BT */ > +&lpuart8 { > + uart-has-rtscts; > + status = "okay"; > +}; > + > +&netc_emdio { /* RGMII2 */ > + ethphy0: ethernet-phy@1 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <0x1>; > + interrupt-parent = <&gpio2>; > + interrupts = <16 IRQ_TYPE_LEVEL_LOW>; > + enet-phy-lane-no-swap; > + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; > + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; > + ti,rx-internal-delay = <DP83867_RGMIIDCTL_1_50_NS>; > + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + }; > + > + ethphy2: ethernet-phy@8 { > + compatible = "ethernet-phy-ieee802.3-c45"; > + reg = <0x8>; > + max-speed = <10000>; /* 10Gbit/s */ > + status = "disabled"; > + }; > +}; > + > +&pcie0 { > + reset-gpio = <&gpio1 10 GPIO_ACTIVE_LOW>; > + vpcie-supply = <®_vdd_3v3>; > + status = "okay"; > +}; > + > +&pcie1 { > + reset-gpio = <&gpio1 14 GPIO_ACTIVE_LOW>; > + vpcie-supply = <®_vdd_3v3>; > + status = "okay"; > +}; > + > +&rv3028 { > + pinctrl-names = "default"; > + pinctrl-0 = <&pinctrl_rtc>; > + interrupt-parent = <&gpio2>; > + interrupts = <18 IRQ_TYPE_LEVEL_LOW>; > + aux-voltage-chargeable = <1>; > + wakeup-source; > + trickle-resistor-ohms = <3000>; > +}; > + > +&scmi_iomuxc { > + pinctrl_lpuart2: lpuart2grp { /* FPSC proprietary */ > + fsl,pins = < > + IMX95_PAD_UART2_TXD__AONMIX_TOP_LPUART2_TX 0x31e > + IMX95_PAD_UART2_RXD__AONMIX_TOP_LPUART2_RX 0x31e > + >; > + }; > + > + pinctrl_lvds0: lvds0grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO20__GPIO2_IO_BIT20 0x31e > + >; > + }; > + > + pinctrl_rtc: rtcgrp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO18__GPIO2_IO_BIT18 0x31e > + >; > + }; > + > + pinctrl_tpm4: tpm4grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO21__TPM4_CH1 0x51e > + >; > + }; > +}; > + > +&tpm4 { > + pinctrl-0 = <&pinctrl_tpm4>; > + pinctrl-names = "default"; > +}; > + > +&usb3 { > + fsl,over-current-active-low; > + fsl,power-active-low; > + status = "okay"; > +}; > + > +&usb3_dwc3 { > + dr_mode = "peripheral"; > + status = "okay"; > +}; > + > +&usb3_phy { > + vbus-supply = <®_vdd_5v0>; > + status = "okay"; > +}; > + > +/* uSD Card */ > +&usdhc2 { > + status = "okay"; > +}; > diff --git a/arch/arm64/boot/dts/freescale/imx95-phycore-fpsc.dtsi b/arch/arm64/boot/dts/freescale/imx95-phycore-fpsc.dtsi > new file mode 100644 > index 0000000000000000000000000000000000000000..7519d5bd06ba800807aaba5495b317cb54632b6c > --- /dev/null > +++ b/arch/arm64/boot/dts/freescale/imx95-phycore-fpsc.dtsi > @@ -0,0 +1,656 @@ > +// SPDX-License-Identifier: (GPL-2.0+ OR MIT) > +/* > + * Copyright 2025 PHYTEC Messtechnik GmbH > + */ > + > +#include <dt-bindings/net/ti-dp83867.h> > +#include "imx95.dtsi" > + > +/ { > + model = "PHYTEC phyCORE-i.MX95 FPSC"; > + compatible = "phytec,imx95-phycore-fpsc", "fsl,imx95"; > + > + aliases { > + ethernet1 = &enetc_port1; > + i2c1 = &lpi2c2; > + i2c2 = &lpi2c5; > + i2c3 = &lpi2c3; > + i2c4 = &lpi2c4; > + i2c5 = &lpi2c1; > + rtc0 = &rv3028; > + rtc1 = &scmi_bbm; > + }; > + > + memory@80000000 { > + device_type = "memory"; > + reg = <0x00000000 0x80000000 0x00000001 0x00000000>; > + }; > + > + reg_nvcc_aon: regulator-nvcc-aon { > + compatible = "regulator-fixed"; > + regulator-always-on; > + regulator-boot-on; > + regulator-max-microvolt = <1800000>; > + regulator-min-microvolt = <1800000>; > + regulator-name = "VDD_IO"; > + }; > + > + reg_usdhc2_vmmc: regulator-usdhc2 { > + compatible = "regulator-fixed"; > + off-on-delay-us = <12000>; > + pinctrl-0 = <&pinctrl_reg_usdhc2_vmmc>; > + pinctrl-names = "default"; > + regulator-max-microvolt = <3300000>; > + regulator-min-microvolt = <3300000>; > + regulator-name = "VDDSW_SD2"; > + gpio = <&gpio3 7 GPIO_ACTIVE_HIGH>; > + enable-active-high; > + }; > + > + reserved-memory { > + ranges; > + #address-cells = <2>; > + #size-cells = <2>; > + > + linux,cma { > + compatible = "shared-dma-pool"; > + alloc-ranges = <0 0x80000000 0 0x7f000000>; > + reusable; > + size = <0 0x3c000000>; > + linux,cma-default; > + }; > + }; > +}; > + > +&enetc_port0 { /* FPSC RGMII2 */ > + phy-mode = "rgmii-id"; > + pinctrl-0 = <&pinctrl_enetc0>; > + pinctrl-names = "default"; > +}; > + > +&enetc_port1 { > + phy-handle = <ðphy1>; > + phy-mode = "rgmii-id"; > + pinctrl-0 = <&pinctrl_enetc1>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&flexcan1 { /* FPSC CAN1 */ > + pinctrl-0 = <&pinctrl_flexcan1>; > + pinctrl-names = "default"; > +}; > + > +&flexcan2 { /* FPSC CAN2 */ > + pinctrl-0 = <&pinctrl_flexcan2>; > + pinctrl-names = "default"; > +}; > + > +&flexspi1 { /* FPSC QSPI */ > + pinctrl-0 = <&pinctrl_flexspi>; > + pinctrl-names = "default"; > +}; > + > +&gpio1 { /* FPSC GPIO */ > + gpio-line-names = "", "", "", "", "GPIO2", > + "GPIO1", "", "", "", "", > + "PCIE1_nPERST", "USB1_PWR_EN", "GPIO3", "USB2_PWR_EN", "PCIE2_nPERST"; > + pinctrl-0 = <&pinctrl_gpio1>; > + pinctrl-names = "default"; > + status = "okay"; > +}; > + > +&gpio2 { /* FPSC GPIO */ > + gpio-line-names = "", "", "", "", "", > + "", "", "", "", "", > + "", "", "", "", "", > + "", "RGMII2_nINT", "GPIO4"; > + pinctrl-0 = <&pinctrl_gpio2>; > + pinctrl-names = "default"; > +}; > + > +&gpio3 { > + gpio-line-names = "", "", "", "", "", > + "", "", "SD2_RESET_B"; > +}; > + > +&gpio4 { > + gpio-line-names = "ENET2_nINT"; > +}; > + > +&gpio5 { > + gpio-line-names = "", "", "", "", "", > + "", "", "", "", "", > + "", "", "", "USB1_OC", "USB2_OC"; > +}; > + > +&lpi2c1 { /* FPSC I2C5 */ > + clock-frequency = <400000>; > + pinctrl-0 = <&pinctrl_lpi2c1>; > + pinctrl-names = "default"; > + status = "okay"; > + > + dram_sense: temperature-sensor@48 { > + compatible = "ti,tmp102"; > + reg = <0x48>; > + #thermal-sensor-cells = <1>; > + }; > + > + emmc_sense: temperature-sensor@49 { > + compatible = "ti,tmp102"; > + reg = <0x49>; > + #thermal-sensor-cells = <1>; > + }; > + > + ethphy_sense: temperature-sensor@4a { > + compatible = "ti,tmp102"; > + reg = <0x4a>; > + #thermal-sensor-cells = <1>; > + }; > + > + pmic_sense: temperature-sensor@4b { > + compatible = "ti,tmp102"; > + reg = <0x4b>; > + #thermal-sensor-cells = <1>; > + }; > + > + /* User EEPROM */ > + eeprom@50 { > + compatible = "st,24c32", "atmel,24c32"; > + reg = <0x50>; > + pagesize = <32>; > + vcc-supply = <®_nvcc_aon>; > + }; > + > + /* Factory EEPROM */ > + eeprom@51 { > + compatible = "st,24c32", "atmel,24c32"; > + reg = <0x51>; > + pagesize = <32>; > + vcc-supply = <®_nvcc_aon>; > + }; > + > + rv3028: rtc@52 { > + compatible = "microcrystal,rv3028"; > + reg = <0x52>; > + }; > + > + /* User EEPROM ID page */ > + eeprom@58 { > + compatible = "st,24c32", "atmel,24c32"; > + reg = <0x58>; > + pagesize = <32>; > + vcc-supply = <®_nvcc_aon>; > + }; > +}; > + > +&lpi2c2 { /* FPSC I2C1 */ > + clock-frequency = <400000>; > + pinctrl-0 = <&pinctrl_lpi2c2>; > + pinctrl-names = "default"; > +}; > + > +&lpi2c3 { /* FPSC I2C3 */ > + clock-frequency = <400000>; > + pinctrl-0 = <&pinctrl_lpi2c3>; > + pinctrl-names = "default"; > +}; > + > +&lpi2c4 { /* FPSC I2C4 */ > + clock-frequency = <400000>; > + pinctrl-0 = <&pinctrl_lpi2c4>; > + pinctrl-names = "default"; > +}; > + > +&lpi2c5 { /* FPSC I2C2 */ > + clock-frequency = <400000>; > + pinctrl-0 = <&pinctrl_lpi2c5>; > + pinctrl-names = "default"; > +}; > + > +&lpspi3 { /* FPSC SPI2 */ > + pinctrl-0 = <&pinctrl_lpspi3>; > + pinctrl-names = "default"; > +}; > + > +&lpspi4 { /* FPSC SPI3 */ > + pinctrl-0 = <&pinctrl_lpspi4>; > + pinctrl-names = "default"; > +}; > + > +&lpspi7 { /* FPSC SPI1 */ > + pinctrl-0 = <&pinctrl_lpspi7>; > + pinctrl-names = "default"; > +}; > + > +&lpuart5 { /* FPSC UART2 */ > + pinctrl-0 = <&pinctrl_lpuart5>; > + pinctrl-names = "default"; > +}; > + > +&lpuart7 { /* FPSC UART3 */ > + pinctrl-0 = <&pinctrl_lpuart7>; > + pinctrl-names = "default"; > +}; > + > +&lpuart8 { /* FPSC UART1 */ > + pinctrl-0 = <&pinctrl_lpuart8>; > + pinctrl-names = "default"; > +}; > + > +&netc_blk_ctrl { > + status = "okay"; > +}; > + > +&netc_emdio { /* FPSC RGMII2 */ > + pinctrl-0 = <&pinctrl_emdio>; > + pinctrl-names = "default"; > + status = "okay"; > + > + ethphy1: ethernet-phy@0 { > + compatible = "ethernet-phy-ieee802.3-c22"; > + reg = <0x0>; > + interrupt-parent = <&gpio4>; > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + enet-phy-lane-no-swap; > + ti,clk-output-sel = <DP83867_CLK_O_SEL_OFF>; > + ti,fifo-depth = <DP83867_PHYCR_FIFO_DEPTH_4_B_NIB>; > + ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + ti,tx-internal-delay = <DP83867_RGMIIDCTL_2_00_NS>; > + }; > +}; > + > +&netcmix_blk_ctrl { > + status = "okay"; > +}; > + > +&pcie0 { /* FPSC PCIE1 */ > + pinctrl-0 = <&pinctrl_pcie0>; > + pinctrl-names = "default"; > +}; > + > +&pcie1 { /* FPSC PCIE2 */ > + pinctrl-0 = <&pinctrl_pcie1>; > + pinctrl-names = "default"; > +}; > + > +&sai5 { /* FPSC SAI1 */ > + pinctrl-0 = <&pinctrl_sai5>; > + pintrc-names = "default"; > +}; > + > +&scmi_iomuxc { > + pinctrl_emdio: emdiogrp { > + fsl,pins = < > + IMX95_PAD_ENET2_MDIO__NETCMIX_TOP_NETC_MDIO 0x97e /* RGMII2_MDIO */ > + IMX95_PAD_ENET2_MDC__NETCMIX_TOP_NETC_MDC 0x502 /* RGMII2_MDC */ > + >; > + }; > + > + pinctrl_enetc0: enetc0grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO16__GPIO2_IO_BIT16 0x31e /* RGMII2_nINT */ > + IMX95_PAD_CCM_CLKO3__NETCMIX_TOP_NETC_TMR_1588_TRIG2 0x31e /* RGMII2_EVENT_IN */ > + IMX95_PAD_CCM_CLKO4__NETCMIX_TOP_NETC_TMR_1588_PP2 0x31e /* RGMII2_EVENT_OUT */ > + > + IMX95_PAD_ENET1_TD3__NETCMIX_TOP_ETH0_RGMII_TD3 0x57e /* RGMII2_TX_3 */ > + IMX95_PAD_ENET1_TD2__NETCMIX_TOP_ETH0_RGMII_TD2 0x57e /* RGMII2_TX_2 */ > + IMX95_PAD_ENET1_TD1__NETCMIX_TOP_ETH0_RGMII_TD1 0x57e /* RGMII2_TX_1 */ > + IMX95_PAD_ENET1_TD0__NETCMIX_TOP_ETH0_RGMII_TD0 0x57e /* RGMII2_TX_0 */ > + IMX95_PAD_ENET1_TX_CTL__NETCMIX_TOP_ETH0_RGMII_TX_CTL 0x57e /* RGMII2_TX_CTL */ > + IMX95_PAD_ENET1_TXC__NETCMIX_TOP_ETH0_RGMII_TX_CLK 0x58e /* RGMII2_TXC */ > + IMX95_PAD_ENET1_RD3__NETCMIX_TOP_ETH0_RGMII_RD3 0x57e /* RGMII2_RX_3 */ > + IMX95_PAD_ENET1_RD2__NETCMIX_TOP_ETH0_RGMII_RD2 0x57e /* RGMII2_RX_2 */ > + IMX95_PAD_ENET1_RD1__NETCMIX_TOP_ETH0_RGMII_RD1 0x57e /* RGMII2_RX_1 */ > + IMX95_PAD_ENET1_RD0__NETCMIX_TOP_ETH0_RGMII_RD0 0x57e /* RGMII2_RX_0 */ > + IMX95_PAD_ENET1_RX_CTL__NETCMIX_TOP_ETH0_RGMII_RX_CTL 0x57e /* RGMII2_RX_CTL */ > + IMX95_PAD_ENET1_RXC__NETCMIX_TOP_ETH0_RGMII_RX_CLK 0x58e /* RGMII2_RXC */ > + >; > + }; > + > + pinctrl_enetc1: enetc1grp { > + fsl,pins = < > + IMX95_PAD_ENET1_MDC__GPIO4_IO_BIT0 0x31e > + IMX95_PAD_ENET2_TD0__NETCMIX_TOP_ETH1_RGMII_TD0 0x57e > + IMX95_PAD_ENET2_TD1__NETCMIX_TOP_ETH1_RGMII_TD1 0x57e > + IMX95_PAD_ENET2_TD2__NETCMIX_TOP_ETH1_RGMII_TD2 0x57e > + IMX95_PAD_ENET2_TD3__NETCMIX_TOP_ETH1_RGMII_TD3 0x57e > + IMX95_PAD_ENET2_TX_CTL__NETCMIX_TOP_ETH1_RGMII_TX_CTL 0x57e > + IMX95_PAD_ENET2_TXC__NETCMIX_TOP_ETH1_RGMII_TX_CLK 0x58e > + IMX95_PAD_ENET2_RD0__NETCMIX_TOP_ETH1_RGMII_RD0 0x57e > + IMX95_PAD_ENET2_RD1__NETCMIX_TOP_ETH1_RGMII_RD1 0x57e > + IMX95_PAD_ENET2_RD2__NETCMIX_TOP_ETH1_RGMII_RD2 0x57e > + IMX95_PAD_ENET2_RD3__NETCMIX_TOP_ETH1_RGMII_RD3 0x57e > + IMX95_PAD_ENET2_RX_CTL__NETCMIX_TOP_ETH1_RGMII_RX_CTL 0x57e > + IMX95_PAD_ENET2_RXC__NETCMIX_TOP_ETH1_RGMII_RX_CLK 0x58e > + >; > + }; > + > + pinctrl_flexcan1: flexcan1grp { > + fsl,pins = < > + IMX95_PAD_PDM_CLK__AONMIX_TOP_CAN1_TX 0x51e /* CAN1_TX */ > + IMX95_PAD_PDM_BIT_STREAM0__AONMIX_TOP_CAN1_RX 0x51e /* CAN1_RX */ > + >; > + }; > + > + pinctrl_flexcan2: flexcan2grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO25__CAN2_TX 0x51e /* CAN2_TX */ > + IMX95_PAD_GPIO_IO27__CAN2_RX 0x51e /* CAN2_RX */ > + >; > + }; > + > + pinctrl_flexspi: flexspigrp { > + fsl,pins = < > + IMX95_PAD_XSPI1_SS0_B__FLEXSPI1_A_SS0_B 0x3fe /* QSPI_CE */ > + IMX95_PAD_XSPI1_SCLK__FLEXSPI1_A_SCLK 0x3fe /* QSPI_CLK */ > + IMX95_PAD_XSPI1_DATA0__FLEXSPI1_A_DATA_BIT0 0x3fe /* QSPI_DATA_0 */ > + IMX95_PAD_XSPI1_DATA1__FLEXSPI1_A_DATA_BIT1 0x3fe /* QSPI_DATA_1 */ > + IMX95_PAD_XSPI1_DATA2__FLEXSPI1_A_DATA_BIT2 0x3fe /* QSPI_DATA_2 */ > + IMX95_PAD_XSPI1_DATA3__FLEXSPI1_A_DATA_BIT3 0x3fe /* QSPI_DATA_3 */ > + IMX95_PAD_XSPI1_DQS__FLEXSPI1_A_DQS 0x3fe /* QSPI_DQS */ > + >; > + }; > + > + pinctrl_gpio1: gpio1grp { > + fsl,pins = < > + IMX95_PAD_UART1_TXD__AONMIX_TOP_GPIO1_IO_BIT5 0x31e /* GPIO1 */ > + IMX95_PAD_UART1_RXD__AONMIX_TOP_GPIO1_IO_BIT4 0x31e /* GPIO2 */ > + IMX95_PAD_SAI1_TXC__AONMIX_TOP_GPIO1_IO_BIT12 0x31e /* GPIO3 */ > + >; > + }; > + > + pinctrl_gpio2: gpio2grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO17__GPIO2_IO_BIT17 0x31e /* GPIO4 */ > + >; > + }; > + > + pinctrl_lpi2c1: lpi2c1grp { > + fsl,pins = < > + IMX95_PAD_I2C1_SCL__AONMIX_TOP_LPI2C1_SCL 0x40000b9e /* I2C5_SCL */ > + IMX95_PAD_I2C1_SDA__AONMIX_TOP_LPI2C1_SDA 0x40000b9e /* I2C5_SDA */ > + >; > + }; > + > + pinctrl_lpi2c2: lpi2c2grp { > + fsl,pins = < > + IMX95_PAD_I2C2_SDA__AONMIX_TOP_LPI2C2_SDA 0x40000b9e /* I2C1_SDA_DNU */ > + IMX95_PAD_I2C2_SCL__AONMIX_TOP_LPI2C2_SCL 0x40000b9e /* I2C1_SCL_DNU */ > + >; > + }; > + > + pinctrl_lpi2c3: lpi2c3grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO28__LPI2C3_SDA 0x40000b9e /* I2C3_SDA */ > + IMX95_PAD_GPIO_IO29__LPI2C3_SCL 0x40000b9e /* I2C3_SCL */ > + >; > + }; > + > + pinctrl_lpi2c4: lpi2c4grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO30__LPI2C4_SDA 0x40000b9e /* I2C4_SDA */ > + IMX95_PAD_GPIO_IO31__LPI2C4_SCL 0x40000b9e /* I2C4_SDL */ > + >; > + }; > + > + pinctrl_lpi2c5: lpi2c5grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO22__LPI2C5_SDA 0x40000b9e /* I2C2_SDA */ > + IMX95_PAD_GPIO_IO23__LPI2C5_SCL 0x40000b9e /* I2C2_SCL */ > + >; > + }; > + > + pinctrl_lpspi3: lpspi3grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO11__LPSPI3_SCK 0x51e /* SPI2_SCLK */ > + IMX95_PAD_GPIO_IO10__LPSPI3_SOUT 0x51e /* SPI2_MOSI */ > + IMX95_PAD_GPIO_IO09__LPSPI3_SIN 0x51e /* SPI2_MISO */ > + IMX95_PAD_GPIO_IO08__LPSPI3_PCS0 0x51e /* SPI2_CS */ > + >; > + }; > + > + pinctrl_lpspi4: lpspi4grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO21__LPSPI4_SCK 0x51e /* SPI3_SCLK */ > + IMX95_PAD_GPIO_IO20__LPSPI4_SOUT 0x51e /* SPI3_MOSI */ > + IMX95_PAD_GPIO_IO19__LPSPI4_SIN 0x51e /* SPI3_MISO */ > + IMX95_PAD_GPIO_IO18__LPSPI4_PCS0 0x51e /* SPI3_CS */ > + >; > + }; > + > + pinctrl_lpspi7: lpspi7grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO07__LPSPI7_SCK 0x51e /* SPI1_SCLK */ > + IMX95_PAD_GPIO_IO06__LPSPI7_SOUT 0x51e /* SPI1_MOSI */ > + IMX95_PAD_GPIO_IO05__LPSPI7_SIN 0x51e /* SPI1_MISO */ > + IMX95_PAD_GPIO_IO04__LPSPI7_PCS0 0x51e /* SPI1_CS */ > + >; > + }; > + > + pinctrl_lpuart5: lpuart5grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO01__LPUART5_RX 0x51e /* UART2_RXD */ > + IMX95_PAD_GPIO_IO00__LPUART5_TX 0x51e /* UART2_TXD */ > + IMX95_PAD_GPIO_IO03__LPUART5_RTS_B 0x51e /* UART2_RTS */ > + IMX95_PAD_GPIO_IO02__LPUART5_CTS_B 0x51e /* UART2_CTS */ > + >; > + }; > + > + pinctrl_lpuart7: lpuart7grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO37__LPUART7_RX 0x31e /* UART3_RXD */ > + IMX95_PAD_GPIO_IO36__LPUART7_TX 0x31e /* UART3_TXD */ > + >; > + }; > + > + pinctrl_lpuart8: lpuart8grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO13__LPUART8_RX 0x51e /* UART1_RXD */ > + IMX95_PAD_GPIO_IO12__LPUART8_TX 0x51e /* UART1_TXD */ > + IMX95_PAD_GPIO_IO15__LPUART8_RTS_B 0x51e /* UART1_RTS */ > + IMX95_PAD_GPIO_IO14__LPUART8_CTS_B 0x51e /* UART1_CTS */ > + >; > + }; > + > + pinctrl_pcie0: pcie0grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO32__HSIOMIX_TOP_PCIE1_CLKREQ_B 0x31e /* PCIE1_nCLKREQ */ > + IMX95_PAD_PDM_BIT_STREAM1__AONMIX_TOP_GPIO1_IO_BIT10 0x31e /* PCIE1_nPERST */ > + >; > + }; > + > + pinctrl_pcie1: pcie1grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO35__HSIOMIX_TOP_PCIE2_CLKREQ_B 0x31e /* PCIE2_nCLKREQ */ > + IMX95_PAD_SAI1_RXD0__AONMIX_TOP_GPIO1_IO_BIT14 0x31e /* PCIE2_nPERST */ > + >; > + }; > + > + pinctrl_reg_usdhc2_vmmc: regusdhc2vmmcgrp { > + fsl,pins = < > + IMX95_PAD_SD2_RESET_B__GPIO3_IO_BIT7 0x31e > + >; > + }; > + > + pinctrl_sai5: sai5grp { > + fsl,pins = < > + IMX95_PAD_XSPI1_DQS__SAI5_RX_SYNC 0x51e /* SAI1_RX_SYNC */ > + IMX95_PAD_XSPI1_SS1_B__SAI5_RX_BCLK 0x51e /* SAI1_RX_BCLK */ > + IMX95_PAD_XSPI1_DATA7__SAI5_RX_DATA_BIT0 0x51e /* SAI1_RX_DATA */ > + IMX95_PAD_XSPI1_DATA5__SAI5_TX_SYNC 0x51e /* SAI1_TX_SYNC */ > + IMX95_PAD_XSPI1_DATA6__SAI5_TX_BCLK 0x51e /* SAI1_TX_BCLK */ > + IMX95_PAD_XSPI1_DATA4__SAI5_TX_DATA_BIT0 0x51e /* SAI1_TX_DATA */ > + >; > + }; > + > + pinctrl_tpm3: tpm3grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO24__TPM3_CH3 0x51e /* PWM1 */ > + >; > + }; > + > + pinctrl_tpm5: tpm5grp { > + fsl,pins = < > + IMX95_PAD_GPIO_IO26__TPM5_CH3 0x51e /* PWM2 */ > + >; > + }; > + > + pinctrl_usbc: usbcgrp { > + fsl,pins = < > + IMX95_PAD_SAI1_TXFS__AONMIX_TOP_GPIO1_IO_BIT11 0x51e /* USB1_PWR_EN */ > + IMX95_PAD_GPIO_IO33__GPIO5_IO_BIT13 0x51e /* USB1_OC */ > + >; > + }; > + > + pinctrl_usb2: usb2grp { > + fsl,pins = < > + IMX95_PAD_SAI1_TXD0__AONMIX_TOP_GPIO1_IO_BIT13 0x51e /* USB2_PWR_EN */ > + IMX95_PAD_GPIO_IO34__GPIO5_IO_BIT14 0x51e /* USB2_OC */ > + >; > + }; > + > + pinctrl_usdhc1: usdhc1grp { > + fsl,pins = < > + IMX95_PAD_SD1_DATA0__USDHC1_DATA0 0x138e > + IMX95_PAD_SD1_DATA1__USDHC1_DATA1 0x138e > + IMX95_PAD_SD1_DATA2__USDHC1_DATA2 0x138e > + IMX95_PAD_SD1_DATA3__USDHC1_DATA3 0x138e > + IMX95_PAD_SD1_DATA4__USDHC1_DATA4 0x138e > + IMX95_PAD_SD1_DATA5__USDHC1_DATA5 0x138e > + IMX95_PAD_SD1_DATA6__USDHC1_DATA6 0x138e > + IMX95_PAD_SD1_DATA7__USDHC1_DATA7 0x138e > + IMX95_PAD_SD1_CMD__USDHC1_CMD 0x138e > + IMX95_PAD_SD1_CLK__USDHC1_CLK 0x158e > + IMX95_PAD_SD1_STROBE__USDHC1_STROBE 0x158e > + >; > + }; > + > + pinctrl_usdhc1_100mhz: usdhc1-100mhzgrp { > + fsl,pins = < > + IMX95_PAD_SD1_DATA0__USDHC1_DATA0 0x138e > + IMX95_PAD_SD1_DATA1__USDHC1_DATA1 0x138e > + IMX95_PAD_SD1_DATA2__USDHC1_DATA2 0x138e > + IMX95_PAD_SD1_DATA3__USDHC1_DATA3 0x138e > + IMX95_PAD_SD1_DATA4__USDHC1_DATA4 0x138e > + IMX95_PAD_SD1_DATA5__USDHC1_DATA5 0x138e > + IMX95_PAD_SD1_DATA6__USDHC1_DATA6 0x138e > + IMX95_PAD_SD1_DATA7__USDHC1_DATA7 0x138e > + IMX95_PAD_SD1_CMD__USDHC1_CMD 0x138e > + IMX95_PAD_SD1_CLK__USDHC1_CLK 0x158e > + IMX95_PAD_SD1_STROBE__USDHC1_STROBE 0x158e > + >; > + }; > + > + pinctrl_usdhc1_200mhz: usdhc1-200mhzgrp { > + fsl,pins = < > + IMX95_PAD_SD1_DATA0__USDHC1_DATA0 0x13fe > + IMX95_PAD_SD1_DATA1__USDHC1_DATA1 0x13fe > + IMX95_PAD_SD1_DATA2__USDHC1_DATA2 0x13fe > + IMX95_PAD_SD1_DATA3__USDHC1_DATA3 0x13fe > + IMX95_PAD_SD1_DATA4__USDHC1_DATA4 0x13fe > + IMX95_PAD_SD1_DATA5__USDHC1_DATA5 0x13fe > + IMX95_PAD_SD1_DATA6__USDHC1_DATA6 0x13fe > + IMX95_PAD_SD1_DATA7__USDHC1_DATA7 0x13fe > + IMX95_PAD_SD1_CMD__USDHC1_CMD 0x13fe > + IMX95_PAD_SD1_CLK__USDHC1_CLK 0x15fe > + IMX95_PAD_SD1_STROBE__USDHC1_STROBE 0x15fe > + >; > + }; > + > + pinctrl_usdhc2: usdhc2grp { > + fsl,pins = < > + IMX95_PAD_SD2_CD_B__USDHC2_CD_B 0x31e /* CD */ > + IMX95_PAD_SD2_CLK__USDHC2_CLK 0x158e /* CLK */ > + IMX95_PAD_SD2_CMD__USDHC2_CMD 0x138e /* CMD */ > + IMX95_PAD_SD2_DATA0__USDHC2_DATA0 0x138e /* DATA0 */ > + IMX95_PAD_SD2_DATA1__USDHC2_DATA1 0x138e /* DATA1 */ > + IMX95_PAD_SD2_DATA2__USDHC2_DATA2 0x138e /* DATA2 */ > + IMX95_PAD_SD2_DATA3__USDHC2_DATA3 0x138e /* DATA3 */ > + IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e > + > + >; > + }; > + > + pinctrl_usdhc2_100mhz: usdhc2-100mhzgrp { > + fsl,pins = < > + IMX95_PAD_SD2_CD_B__USDHC2_CD_B 0x31e /* CD */ > + IMX95_PAD_SD2_CLK__USDHC2_CLK 0x158e /* CLK */ > + IMX95_PAD_SD2_CMD__USDHC2_CMD 0x138e /* CMD */ > + IMX95_PAD_SD2_DATA0__USDHC2_DATA0 0x138e /* DATA0 */ > + IMX95_PAD_SD2_DATA1__USDHC2_DATA1 0x138e /* DATA1 */ > + IMX95_PAD_SD2_DATA2__USDHC2_DATA2 0x138e /* DATA2 */ > + IMX95_PAD_SD2_DATA3__USDHC2_DATA3 0x138e /* DATA3 */ > + IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e > + >; > + }; > + > + pinctrl_usdhc2_200mhz: usdhc2-200mhzgrp { > + fsl,pins = < > + IMX95_PAD_SD2_CD_B__USDHC2_CD_B 0x31e /* CD */ > + IMX95_PAD_SD2_CLK__USDHC2_CLK 0x15fe /* CLK */ > + IMX95_PAD_SD2_CMD__USDHC2_CMD 0x13fe /* CMD */ > + IMX95_PAD_SD2_DATA0__USDHC2_DATA0 0x13fe /* DATA0 */ > + IMX95_PAD_SD2_DATA1__USDHC2_DATA1 0x13fe /* DATA1 */ > + IMX95_PAD_SD2_DATA2__USDHC2_DATA2 0x13fe /* DATA2 */ > + IMX95_PAD_SD2_DATA3__USDHC2_DATA3 0x13fe /* DATA3 */ > + IMX95_PAD_SD2_VSELECT__USDHC2_VSELECT 0x51e > + >; > + }; > + > + pinctrl_usdhc3: usdhc3grp { > + fsl,pins = < > + IMX95_PAD_SD3_CLK__USDHC3_CLK 0x158e /* SDIO_CLK */ > + IMX95_PAD_SD3_CMD__USDHC3_CMD 0x138e /* SDIO_CMD */ > + IMX95_PAD_SD3_DATA0__USDHC3_DATA0 0x138e /* SDIO_DATA0 */ > + IMX95_PAD_SD3_DATA1__USDHC3_DATA1 0x138e /* SDIO_DATA1 */ > + IMX95_PAD_SD3_DATA2__USDHC3_DATA2 0x138e /* SDIO_DATA2 */ > + IMX95_PAD_SD3_DATA3__USDHC3_DATA3 0x138e /* SDIO_DATA3 */ > + >; > + }; > +}; > + > +&tpm3 { /* FPSC PWM1 */ > + pinctrl-0 = <&pinctrl_tpm3>; > + pinctrl-names = "default"; > +}; > + > +&tpm5 { /* FPSC PWM2 */ > + pinctrl-0 = <&pinctrl_tpm5>; > + pinctrl-names = "default"; > +}; > + > +&usb3 { /* FPSC USB1 */ > + pinctrl-0 = <&pinctrl_usbc>; > + pinctrl-names = "default"; > +}; > + > +&usdhc1 { > + bus-width = <8>; > + non-removable; > + no-sd; > + no-sdio; > + pinctrl-0 = <&pinctrl_usdhc1>; > + pinctrl-1 = <&pinctrl_usdhc1_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc1_200mhz>; > + pinctrl-3 = <&pinctrl_usdhc1>; > + pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; > + status = "okay"; > +}; > + > +&usdhc2 { /* FPSC SDCARD */ > + bus-width = <4>; > + disable-wp; > + pinctrl-0 = <&pinctrl_usdhc2>; > + pinctrl-1 = <&pinctrl_usdhc2_100mhz>; > + pinctrl-2 = <&pinctrl_usdhc2_200mhz>; > + pinctrl-3 = <&pinctrl_usdhc2>; > + pinctrl-names = "default", "state_100mhz", "state_200mhz", "sleep"; > + sd-uhs-sdr104; > + vmmc-supply = <®_usdhc2_vmmc>; > +}; > + > +&usdhc3 { /* FPSC SDIO */ > + pinctrl-0 = <&pinctrl_usdhc3>; > + pinctrl-names = "default"; > +}; > > -- > 2.43.0 > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC 2025-06-11 13:05 [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Yannic Moog 2025-06-11 13:05 ` [PATCH v3 1/2] dt-bindings: add imx95-libra-rdk-fpsc Yannic Moog 2025-06-11 13:05 ` [PATCH v3 2/2] arm64: dts: add imx95-libra-rdk-fpsc board Yannic Moog @ 2025-06-12 20:12 ` Rob Herring (Arm) 2025-07-08 7:47 ` Yannic Moog 2025-07-11 7:30 ` Shawn Guo 3 siblings, 1 reply; 7+ messages in thread From: Rob Herring (Arm) @ 2025-06-12 20:12 UTC (permalink / raw) To: Yannic Moog Cc: linux-kernel, Catalin Marinas, Yashwanth Varakala, Shawn Guo, Krzysztof Kozlowski, Will Deacon, Teresa Remmet, Benjamin Hahn, Jan Remmet, Conor Dooley, devicetree, Conor Dooley, upstream, Fabio Estevam, linux-arm-kernel, Pengutronix Kernel Team, Sascha Hauer, imx On Wed, 11 Jun 2025 15:05:29 +0200, Yannic Moog wrote: > The Libra i.MX 95 is a SBC that consists of the Libra base board > and the phyCORE i.MX 95 FPSC SoM. > This series adds its binding and device trees. > > --- > Changes in v3: > - fix more style issues > - remove the rs232/485 gpio hog -> switch on the board is used instead > - remove erroneously added build artefacts > - Link to v2: https://lore.kernel.org/r/20250509-wip-y-moog-phytec-de-imx95-libra-v2-2-b241a915f2be@phytec.de > > Changes in v2: > - fix indentation error in bindings > - align alias naming with FPSC enumeration > - Link to v1: https://lore.kernel.org/r/20250507-wip-y-moog-phytec-de-imx95-libra-v1-0-4b73843ad4cd@phytec.de > > --- > Yannic Moog (2): > dt-bindings: add imx95-libra-rdk-fpsc > arm64: dts: add imx95-libra-rdk-fpsc board > > Documentation/devicetree/bindings/arm/fsl.yaml | 7 + > arch/arm64/boot/dts/freescale/Makefile | 1 + > .../boot/dts/freescale/imx95-libra-rdk-fpsc.dts | 318 ++++++++++ > .../boot/dts/freescale/imx95-phycore-fpsc.dtsi | 656 +++++++++++++++++++++ > 4 files changed, 982 insertions(+) > --- > base-commit: 68087d05675e3ac0ed632bc7b175abf06617c584 > change-id: 20250415-wip-y-moog-phytec-de-imx95-libra-27c9ce555b91 > > Best regards, > -- > Yannic Moog <y.moog@phytec.de> > > > My bot found new DTB warnings on the .dts files added or changed in this series. Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings are fixed by another series. Ultimately, it is up to the platform maintainer whether these warnings are acceptable or not. No need to reply unless the platform maintainer has comments. If you already ran DT checks and didn't see these error(s), then make sure dt-schema is up to date: pip3 install dtschema --upgrade This patch series was applied (using b4) to base: Base: using specified base-commit 68087d05675e3ac0ed632bc7b175abf06617c584 If this is not the correct base, please add 'base-commit' tag (or use b4 which does this automatically) New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/freescale/' for 20250611-wip-y-moog-phytec-de-imx95-libra-v3-0-c8d09f1bdbf0@phytec.de: arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usb@4c200000 (fsl,imx95-usb): compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,imx95-usb', 'fsl,imx7d-usb', 'fsl,imx27-usb'] is too long 'fsl,imx95-usb' is not one of ['fsl,imx27-usb'] 'fsl,imx95-usb' is not one of ['fsl,imx23-usb', 'fsl,imx25-usb', 'fsl,imx28-usb', 'fsl,imx35-usb', 'fsl,imx50-usb', 'fsl,imx51-usb', 'fsl,imx53-usb', 'fsl,imx6q-usb', 'fsl,imx6sl-usb', 'fsl,imx6sx-usb', 'fsl,imx6ul-usb', 'fsl,imx7d-usb', 'fsl,vf610-usb'] 'fsl,imx95-usb' is not one of ['fsl,imx8dxl-usb', 'fsl,imx8ulp-usb'] 'fsl,imx95-usb' is not one of ['fsl,imx8mm-usb', 'fsl,imx8mn-usb', 'fsl,imx93-usb'] 'fsl,imx95-usb' is not one of ['fsl,imx6sll-usb', 'fsl,imx7ulp-usb'] 'fsl,imx27-usb' was expected 'fsl,imx7ulp-usb' was expected 'fsl,imx6ul-usb' was expected from schema $id: http://devicetree.org/schemas/usb/chipidea,usb2-imx.yaml# arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usb@4c200000 (fsl,imx95-usb): interrupts: [[0, 176, 4], [0, 174, 4]] is too long from schema $id: http://devicetree.org/schemas/usb/chipidea,usb2-imx.yaml# arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: /soc/usb@4c200000: failed to match any schema with compatible: ['fsl,imx95-usb', 'fsl,imx7d-usb', 'fsl,imx27-usb'] arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usbmisc@4c200200 (fsl,imx95-usbmisc): compatible: 'oneOf' conditional failed, one must be fixed: ['fsl,imx95-usbmisc', 'fsl,imx7d-usbmisc', 'fsl,imx6q-usbmisc'] is too long 'fsl,imx95-usbmisc' is not one of ['fsl,imx25-usbmisc', 'fsl,imx27-usbmisc', 'fsl,imx35-usbmisc', 'fsl,imx51-usbmisc', 'fsl,imx53-usbmisc', 'fsl,imx6q-usbmisc', 'fsl,vf610-usbmisc'] 'fsl,imx95-usbmisc' is not one of ['fsl,imx6ul-usbmisc', 'fsl,imx6sl-usbmisc', 'fsl,imx6sx-usbmisc', 'fsl,imx7d-usbmisc'] 'fsl,imx95-usbmisc' is not one of ['fsl,imx7ulp-usbmisc', 'fsl,imx8mm-usbmisc', 'fsl,imx8mn-usbmisc', 'fsl,imx8ulp-usbmisc'] 'fsl,imx6sll-usbmisc' was expected 'fsl,imx6q-usbmisc' was expected 'fsl,imx6ul-usbmisc' was expected from schema $id: http://devicetree.org/schemas/usb/fsl,usbmisc.yaml# arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usbmisc@4c200200 (fsl,imx95-usbmisc): reg: [[0, 1277166080, 0, 512], [0, 1275133972, 0, 4]] is too long from schema $id: http://devicetree.org/schemas/usb/fsl,usbmisc.yaml# arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: /soc/usbmisc@4c200200: failed to match any schema with compatible: ['fsl,imx95-usbmisc', 'fsl,imx7d-usbmisc', 'fsl,imx6q-usbmisc'] ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC 2025-06-12 20:12 ` [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Rob Herring (Arm) @ 2025-07-08 7:47 ` Yannic Moog 0 siblings, 0 replies; 7+ messages in thread From: Yannic Moog @ 2025-07-08 7:47 UTC (permalink / raw) To: Shawn Guo Cc: linux-kernel@vger.kernel.org, Catalin Marinas, Yashwanth Varakala, Krzysztof Kozlowski, Will Deacon, Teresa Remmet, Benjamin Hahn, Jan Remmet, Conor Dooley, devicetree@vger.kernel.org, Conor Dooley, upstream@lists.phytec.de, Fabio Estevam, linux-arm-kernel@lists.infradead.org, Pengutronix Kernel Team, Sascha Hauer, imx@lists.linux.dev, Rob Herring (Arm) Hi Shawn, Afaik these warning were due to misalignment of bindings and devicetree patches. They have since been resolved, at least my CHECK_DTBS run is clean again. Is there something that is holding this series up from being picked up? If you want me to, I can also resend. Yannic Am Donnerstag, dem 12.06.2025 um 15:12 -0500 schrieb Rob Herring (Arm): > > On Wed, 11 Jun 2025 15:05:29 +0200, Yannic Moog wrote: > > The Libra i.MX 95 is a SBC that consists of the Libra base board > > and the phyCORE i.MX 95 FPSC SoM. > > This series adds its binding and device trees. > > > > --- > > Changes in v3: > > - fix more style issues > > - remove the rs232/485 gpio hog -> switch on the board is used instead > > - remove erroneously added build artefacts > > - Link to v2: > > https://lore.kernel.org/r/20250509-wip-y-moog-phytec-de-imx95-libra-v2-2-b241a915f2be@phytec.de > > > > Changes in v2: > > - fix indentation error in bindings > > - align alias naming with FPSC enumeration > > - Link to v1: > > https://lore.kernel.org/r/20250507-wip-y-moog-phytec-de-imx95-libra-v1-0-4b73843ad4cd@phytec.de > > > > --- > > Yannic Moog (2): > > dt-bindings: add imx95-libra-rdk-fpsc > > arm64: dts: add imx95-libra-rdk-fpsc board > > > > Documentation/devicetree/bindings/arm/fsl.yaml | 7 + > > arch/arm64/boot/dts/freescale/Makefile | 1 + > > .../boot/dts/freescale/imx95-libra-rdk-fpsc.dts | 318 ++++++++++ > > .../boot/dts/freescale/imx95-phycore-fpsc.dtsi | 656 > > +++++++++++++++++++++ > > 4 files changed, 982 insertions(+) > > --- > > base-commit: 68087d05675e3ac0ed632bc7b175abf06617c584 > > change-id: 20250415-wip-y-moog-phytec-de-imx95-libra-27c9ce555b91 > > > > Best regards, > > -- > > Yannic Moog <y.moog@phytec.de> > > > > > > > > > My bot found new DTB warnings on the .dts files added or changed in this > series. > > Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings > are fixed by another series. Ultimately, it is up to the platform > maintainer whether these warnings are acceptable or not. No need to reply > unless the platform maintainer has comments. > > If you already ran DT checks and didn't see these error(s), then > make sure dt-schema is up to date: > > pip3 install dtschema --upgrade > > > This patch series was applied (using b4) to base: > Base: using specified base-commit 68087d05675e3ac0ed632bc7b175abf06617c584 > > If this is not the correct base, please add 'base-commit' tag > (or use b4 which does this automatically) > > New warnings running 'make CHECK_DTBS=y for arch/arm64/boot/dts/freescale/' > for 20250611-wip-y-moog-phytec-de-imx95-libra-v3-0-c8d09f1bdbf0@phytec.de: > > arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usb@4c200000 > (fsl,imx95-usb): compatible: 'oneOf' conditional failed, one must be fixed: > ['fsl,imx95-usb', 'fsl,imx7d-usb', 'fsl,imx27-usb'] is too long > 'fsl,imx95-usb' is not one of ['fsl,imx27-usb'] > 'fsl,imx95-usb' is not one of ['fsl,imx23-usb', 'fsl,imx25-usb', > 'fsl,imx28-usb', 'fsl,imx35-usb', 'fsl,imx50-usb', 'fsl,imx51-usb', > 'fsl,imx53-usb', 'fsl,imx6q-usb', 'fsl,imx6sl-usb', 'fsl,imx6sx-usb', > 'fsl,imx6ul-usb', 'fsl,imx7d-usb', 'fsl,vf610-usb'] > 'fsl,imx95-usb' is not one of ['fsl,imx8dxl-usb', 'fsl,imx8ulp-usb'] > 'fsl,imx95-usb' is not one of ['fsl,imx8mm-usb', 'fsl,imx8mn-usb', > 'fsl,imx93-usb'] > 'fsl,imx95-usb' is not one of ['fsl,imx6sll-usb', 'fsl,imx7ulp-usb'] > 'fsl,imx27-usb' was expected > 'fsl,imx7ulp-usb' was expected > 'fsl,imx6ul-usb' was expected > from schema $id: > http://devicetree.org/schemas/usb/chipidea,usb2-imx.yaml# > arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usb@4c200000 > (fsl,imx95-usb): interrupts: [[0, 176, 4], [0, 174, 4]] is too long > from schema $id: > http://devicetree.org/schemas/usb/chipidea,usb2-imx.yaml# > arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: /soc/usb@4c200000: > failed to match any schema with compatible: ['fsl,imx95-usb', 'fsl,imx7d-usb', > 'fsl,imx27-usb'] > arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usbmisc@4c200200 > (fsl,imx95-usbmisc): compatible: 'oneOf' conditional failed, one must be > fixed: > ['fsl,imx95-usbmisc', 'fsl,imx7d-usbmisc', 'fsl,imx6q-usbmisc'] is > too long > 'fsl,imx95-usbmisc' is not one of ['fsl,imx25-usbmisc', 'fsl,imx27- > usbmisc', 'fsl,imx35-usbmisc', 'fsl,imx51-usbmisc', 'fsl,imx53-usbmisc', > 'fsl,imx6q-usbmisc', 'fsl,vf610-usbmisc'] > 'fsl,imx95-usbmisc' is not one of ['fsl,imx6ul-usbmisc', 'fsl,imx6sl- > usbmisc', 'fsl,imx6sx-usbmisc', 'fsl,imx7d-usbmisc'] > 'fsl,imx95-usbmisc' is not one of ['fsl,imx7ulp-usbmisc', > 'fsl,imx8mm-usbmisc', 'fsl,imx8mn-usbmisc', 'fsl,imx8ulp-usbmisc'] > 'fsl,imx6sll-usbmisc' was expected > 'fsl,imx6q-usbmisc' was expected > 'fsl,imx6ul-usbmisc' was expected > from schema $id: http://devicetree.org/schemas/usb/fsl,usbmisc.yaml# > arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: usbmisc@4c200200 > (fsl,imx95-usbmisc): reg: [[0, 1277166080, 0, 512], [0, 1275133972, 0, 4]] is > too long > from schema $id: http://devicetree.org/schemas/usb/fsl,usbmisc.yaml# > arch/arm64/boot/dts/freescale/imx95-libra-rdk-fpsc.dtb: /soc/usbmisc@4c200200: > failed to match any schema with compatible: ['fsl,imx95-usbmisc', 'fsl,imx7d- > usbmisc', 'fsl,imx6q-usbmisc'] > > > > ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC 2025-06-11 13:05 [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Yannic Moog ` (2 preceding siblings ...) 2025-06-12 20:12 ` [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Rob Herring (Arm) @ 2025-07-11 7:30 ` Shawn Guo 3 siblings, 0 replies; 7+ messages in thread From: Shawn Guo @ 2025-07-11 7:30 UTC (permalink / raw) To: Yannic Moog Cc: Rob Herring, Krzysztof Kozlowski, Conor Dooley, Shawn Guo, Sascha Hauer, Pengutronix Kernel Team, Fabio Estevam, Catalin Marinas, Will Deacon, upstream, Benjamin Hahn, Teresa Remmet, Yashwanth Varakala, Jan Remmet, devicetree, linux-kernel, imx, linux-arm-kernel, Conor Dooley On Wed, Jun 11, 2025 at 03:05:29PM +0200, Yannic Moog wrote: > Yannic Moog (2): > dt-bindings: add imx95-libra-rdk-fpsc > arm64: dts: add imx95-libra-rdk-fpsc board Applied both, thanks! ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2025-07-11 7:50 UTC | newest] Thread overview: 7+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2025-06-11 13:05 [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Yannic Moog 2025-06-11 13:05 ` [PATCH v3 1/2] dt-bindings: add imx95-libra-rdk-fpsc Yannic Moog 2025-06-11 13:05 ` [PATCH v3 2/2] arm64: dts: add imx95-libra-rdk-fpsc board Yannic Moog 2025-06-11 16:41 ` Frank Li 2025-06-12 20:12 ` [PATCH v3 0/2] Add new imx imx95-libra-rdk-fpsc SBC Rob Herring (Arm) 2025-07-08 7:47 ` Yannic Moog 2025-07-11 7:30 ` Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox