* Re: [PATCH] arm64: dts: allwinner: orangepi-zero2: Read the SPI NOR over two lines
2026-11-18 3:55 [PATCH] arm64: dts: allwinner: orangepi-zero2: Read the SPI NOR over two lines Arun Iyengar via B4 Relay
@ 2026-11-18 11:19 ` Andre Przywara
0 siblings, 0 replies; 2+ messages in thread
From: Andre Przywara @ 2026-11-18 11:19 UTC (permalink / raw)
To: aiyengar1990, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Chen-Yu Tsai, Jernej Skrabec, Samuel Holland
Cc: devicetree, linux-arm-kernel, linux-sunxi, linux-kernel
Hi,
On 11/18/26 04:55, Arun Iyengar via B4 Relay wrote:
> From: Arun Iyengar <aiyengar1990@gmail.com>
>
> WP# and HOLD# are tied to VCC (schematic v1.3), so read over two lines.
>
> Signed-off-by: Arun Iyengar <aiyengar1990@gmail.com>
> ---
> Needs the spi-sun6i H616 dual read series v2 (prerequisite below).
I don't think it does, and this dependency wouldn't be legal anyway: the
DT and Linux driver code are independent, even though they live in the
same repository.
So as it stands: if you specify a 2 bit wide bus, but the driver doesn't
support this (older kernels), the driver will just ignore this, though
you get a message:
[ 4.226908] spi spi0.0: setup: ignoring unsupported mode bits 400
So there is not hard dependency, functionality-wise, though it will be
faster only if you have both the driver and the DT changes.
> Tested on an Orange Pi Zero2 with it: 1-1-2 reads (opcode 0x3b), 2 MiB in
> 0.28 s instead of 0.52 s, identical data.
>
> Developed with Claude (Anthropic), which wrote the commit message. I
> reviewed it.
> ---
> arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts | 1 +
> 1 file changed, 1 insertion(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> index 90c25e12e189..fb117116002e 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h616-orangepi-zero2.dts
> @@ -150,6 +150,7 @@ &pio {
>
> &spi0 {
> flash@0 {
This double reference looks odd. Why not just add a label to the flash
node, and skip the spi0 reference altogether? Should have been done on
the patch adding the supply (which has been already merged), but maybe
we can still rectify this.
> + spi-rx-bus-width = <2>;
Please note that this is true for the OrangePi Zero3 as well, so this
property should be moved into sun50i-h616-orangepi-zero.dtsi.
Tested this on my Zero3 board, it works and reads the entire 16MB flash
in 1.8 instead of 3.5 seconds.
Cheers,
Andre
> vcc-supply = <®_aldo1>;
> };
> };
>
> ---
> base-commit: a203a4bac3316451a3036653657c8b250dea2055
> change-id: 20261115-zero2-spi-nor-dual-read-645a6de25e81
> prerequisite-message-id: <20261116-spi-sun6i-h616-dual-read-v2-0-e0c66eb71e20@gmail.com>
> prerequisite-patch-id: 28b145097d0f859e5bd27bcc5028d0915f3ba4bd
> prerequisite-patch-id: fb47570beb53613acb42c518fd1999e05e0c54fb
>
> Best regards,
> --
> Arun Iyengar <aiyengar1990@gmail.com>
^ permalink raw reply [flat|nested] 2+ messages in thread