[PATCH] thermal/drivers/imx: Disable clock on runtime resume failure

[PATCH] thermal/drivers/imx: Disable clock on runtime resume failure

[Can Peng]

imx_thermal_runtime_resume() enables the thermal clock before
powering up the sensor and enabling measurements.

If either regmap_write() fails, the function returns with the clock
still enabled. This leaves the clock enable count unbalanced after a
failed runtime resume.

Disable the clock on those failure paths before returning the error.

Fixes: 4cf2ddf16e17 ("thermal/drivers/imx: Implement runtime PM support")
Cc: stable@vger.kernel.org
Signed-off-by: Can Peng <pengcan@kylinos.cn>
---
 drivers/thermal/imx_thermal.c | 9 +++++++--
 1 file changed, 7 insertions(+), 2 deletions(-)

diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
index 5aaacbc53478..b0e88b6a9352 100644
--- a/drivers/thermal/imx_thermal.c
+++ b/drivers/thermal/imx_thermal.c
@@ -832,12 +832,12 @@ static int imx_thermal_runtime_resume(struct device *dev)
 	ret = regmap_write(map, socdata->sensor_ctrl + REG_CLR,
 			   socdata->power_down_mask);
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	ret = regmap_write(map, socdata->sensor_ctrl + REG_SET,
 			   socdata->measure_temp_mask);
 	if (ret)
-		return ret;
+		goto disable_clk;
 
 	/*
 	 * According to the temp sensor designers, it may require up to ~17us
@@ -846,6 +846,11 @@ static int imx_thermal_runtime_resume(struct device *dev)
 	usleep_range(20, 50);
 
 	return 0;
+
+disable_clk:
+	clk_disable_unprepare(data->thermal_clk);
+
+	return ret;
 }
 
 static const struct dev_pm_ops imx_thermal_pm_ops = {
-- 
2.53.0

Re: [PATCH] thermal/drivers/imx: Disable clock on runtime resume failure

[Frank Li]

On Wed, Jul 22, 2026 at 04:49:09PM +0800, Can Peng wrote:
> imx_thermal_runtime_resume() enables the thermal clock before
> powering up the sensor and enabling measurements.
>
> If either regmap_write() fails, the function returns with the clock
> still enabled. This leaves the clock enable count unbalanced after a
> failed runtime resume.
>
> Disable the clock on those failure paths before returning the error.
>
> Fixes: 4cf2ddf16e17 ("thermal/drivers/imx: Implement runtime PM support")
> Cc: stable@vger.kernel.org
> Signed-off-by: Can Peng <pengcan@kylinos.cn>
> ---

Reviewed-by: Frank Li <Frank.Li@nxp.com>

>  drivers/thermal/imx_thermal.c | 9 +++++++--
>  1 file changed, 7 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/thermal/imx_thermal.c b/drivers/thermal/imx_thermal.c
> index 5aaacbc53478..b0e88b6a9352 100644
> --- a/drivers/thermal/imx_thermal.c
> +++ b/drivers/thermal/imx_thermal.c
> @@ -832,12 +832,12 @@ static int imx_thermal_runtime_resume(struct device *dev)
>  	ret = regmap_write(map, socdata->sensor_ctrl + REG_CLR,
>  			   socdata->power_down_mask);
>  	if (ret)
> -		return ret;
> +		goto disable_clk;
>
>  	ret = regmap_write(map, socdata->sensor_ctrl + REG_SET,
>  			   socdata->measure_temp_mask);
>  	if (ret)
> -		return ret;
> +		goto disable_clk;
>
>  	/*
>  	 * According to the temp sensor designers, it may require up to ~17us
> @@ -846,6 +846,11 @@ static int imx_thermal_runtime_resume(struct device *dev)
>  	usleep_range(20, 50);
>
>  	return 0;
> +
> +disable_clk:
> +	clk_disable_unprepare(data->thermal_clk);
> +
> +	return ret;
>  }
>
>  static const struct dev_pm_ops imx_thermal_pm_ops = {
> --
> 2.53.0
>
>