From: "Nícolas F. R. A. Prado" <nfraprado@collabora.com>
To: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: chunkuang.hu@kernel.org, p.zabel@pengutronix.de,
airlied@gmail.com, daniel@ffwll.ch, matthias.bgg@gmail.com,
dri-devel@lists.freedesktop.org,
linux-mediatek@lists.infradead.org, linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org, kernel@collabora.com,
wenst@chromium.org
Subject: Re: [PATCH v3 9/9] drm/mediatek: dp: Add support for embedded DisplayPort aux-bus
Date: Fri, 23 Jun 2023 09:29:21 -0400 [thread overview]
Message-ID: <d7d8db9c-a646-46f7-ab88-d41184b51f26@notapiano> (raw)
In-Reply-To: <20230404104800.301150-10-angelogioacchino.delregno@collabora.com>
On Tue, Apr 04, 2023 at 12:48:00PM +0200, AngeloGioacchino Del Regno wrote:
> For the eDP case we can support using aux-bus on MediaTek DP: this
> gives us the possibility to declare our panel as generic "panel-edp"
> which will automatically configure the timings and available modes
> via the EDID that we read from it.
>
> To do this, move the panel parsing at the end of the probe function
> so that the hardware is initialized beforehand and also initialize
> the DPTX AUX block and power both on as, when we populate the
> aux-bus, the panel driver will trigger an EDID read to perform
> panel detection.
>
> Last but not least, since now the AUX transfers can happen in the
> separated aux-bus, it was necessary to add an exclusion for the
> cable_plugged_in check in `mtk_dp_aux_transfer()` and the easiest
> way to do this is to simply ignore checking that when the bridge
> type is eDP.
>
> Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
> ---
> drivers/gpu/drm/mediatek/mtk_dp.c | 61 ++++++++++++++++++++++++++-----
> 1 file changed, 51 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/gpu/drm/mediatek/mtk_dp.c b/drivers/gpu/drm/mediatek/mtk_dp.c
> index a67143c22024..8109f5b4392b 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dp.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dp.c
[..]
> @@ -2571,6 +2585,33 @@ static int mtk_dp_probe(struct platform_device *pdev)
> mtk_dp->need_debounce = true;
> timer_setup(&mtk_dp->debounce_timer, mtk_dp_debounce_timer, 0);
>
> + if (mtk_dp->bridge.type == DRM_MODE_CONNECTOR_eDP) {
> + /* Initialize, reset and poweron the DPTX AUX block */
> + mtk_dp_initialize_aux_settings(mtk_dp);
> + mtk_dp_power_enable(mtk_dp);
> +
> + /* Power on the panel to allow EDID read from aux-bus */
> + mtk_dp_aux_panel_poweron(mtk_dp, true);
> +
> + ret = devm_of_dp_aux_populate_bus(&mtk_dp->aux, NULL);
This patch causes
.../bin/aarch64-none-linux-gnu-ld: Unexpected GOT/PLT entries detected!
.../bin/aarch64-none-linux-gnu-ld: Unexpected run-time procedure linkages detected!
.../bin/aarch64-none-linux-gnu-ld: drivers/gpu/drm/mediatek/mtk_dp.o: in function `mtk_dp_probe':
.../drivers/gpu/drm/mediatek/mtk_dp.c:2595: undefined reference to `devm_of_dp_aux_populate_bus'
You need
diff --git a/drivers/gpu/drm/mediatek/Kconfig b/drivers/gpu/drm/mediatek/Kconfig
index b451dee64d34..76cab28e010c 100644
--- a/drivers/gpu/drm/mediatek/Kconfig
+++ b/drivers/gpu/drm/mediatek/Kconfig
@@ -26,6 +26,7 @@ config DRM_MEDIATEK_DP
select PHY_MTK_DP
select DRM_DISPLAY_HELPER
select DRM_DISPLAY_DP_HELPER
+ select DRM_DP_AUX_BUS
help
DRM/KMS Display Port driver for MediaTek SoCs.
Thanks,
Nícolas
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-06-23 13:30 UTC|newest]
Thread overview: 22+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-04-04 10:47 [PATCH v3 0/9] MediaTek DisplayPort: support eDP and aux-bus AngeloGioacchino Del Regno
2023-04-04 10:47 ` [PATCH v3 1/9] drm/mediatek: dp: Cache EDID for eDP panel AngeloGioacchino Del Regno
2023-04-12 7:08 ` Matthias Brugger
2023-04-12 8:06 ` AngeloGioacchino Del Regno
2023-04-12 10:39 ` Matthias Brugger
2023-04-04 10:47 ` [PATCH v3 2/9] drm/mediatek: dp: Move AUX and panel poweron/off sequence to function AngeloGioacchino Del Regno
2023-04-06 8:20 ` Chen-Yu Tsai
2023-04-06 8:26 ` AngeloGioacchino Del Regno
2023-04-04 10:47 ` [PATCH v3 3/9] drm/mediatek: dp: Always return connected status for eDP in .detect() AngeloGioacchino Del Regno
2023-04-04 10:47 ` [PATCH v3 4/9] drm/mediatek: dp: Always set cable_plugged_in at resume for eDP panel AngeloGioacchino Del Regno
2023-04-04 10:47 ` [PATCH v3 5/9] drm/mediatek: dp: Change logging to dev for mtk_dp_aux_transfer() AngeloGioacchino Del Regno
2023-04-06 6:20 ` Chen-Yu Tsai
2023-04-04 10:47 ` [PATCH v3 6/9] drm/mediatek: dp: Enable event interrupt only when bridge attached AngeloGioacchino Del Regno
2023-04-04 10:47 ` [PATCH v3 7/9] drm/mediatek: dp: Use devm variant of drm_bridge_add() AngeloGioacchino Del Regno
2023-04-04 10:47 ` [PATCH v3 8/9] drm/mediatek: dp: Move AUX_P0 setting to mtk_dp_initialize_aux_settings() AngeloGioacchino Del Regno
2023-04-04 10:48 ` [PATCH v3 9/9] drm/mediatek: dp: Add support for embedded DisplayPort aux-bus AngeloGioacchino Del Regno
2023-06-23 13:29 ` Nícolas F. R. A. Prado [this message]
2023-06-23 16:22 ` Nícolas F. R. A. Prado
2023-04-06 7:20 ` [PATCH v3 0/9] MediaTek DisplayPort: support eDP and aux-bus Chen-Yu Tsai
2023-04-06 8:25 ` AngeloGioacchino Del Regno
2023-04-06 8:43 ` Chen-Yu Tsai
2023-05-30 6:52 ` AngeloGioacchino Del Regno
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=d7d8db9c-a646-46f7-ab88-d41184b51f26@notapiano \
--to=nfraprado@collabora.com \
--cc=airlied@gmail.com \
--cc=angelogioacchino.delregno@collabora.com \
--cc=chunkuang.hu@kernel.org \
--cc=daniel@ffwll.ch \
--cc=dri-devel@lists.freedesktop.org \
--cc=kernel@collabora.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-mediatek@lists.infradead.org \
--cc=matthias.bgg@gmail.com \
--cc=p.zabel@pengutronix.de \
--cc=wenst@chromium.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox