[PATCH 0/8] SM8450 QoL changes

[PATCH 0/8] SM8450 QoL changes

[Esteban Urrutia via B4 Relay]

Hello. This is my first attempt at contributing to the Linux kernel.

I've been mainlining an SM8475 based device for quite some time now and
I feel now's the proper time to start submitting patches.
I'm starting with the smallest part which are mostly modifications
regarding the current support for the SM8450 SoC.

Regards,
Esteban

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
Esteban Urrutia (8):
      clk: qcom: dispcc-sm8450: Fix mdss clocks
      arm64: dts: qcom: sm8450: Remove unneeded reserved memory nodes
      arm64: dts: qcom: sm8450: Modify GPU operating points
      arm64: dts: qcom: sm8450: Add missing PCM_OUT port
      iommu/arm-smmu-qcom: Add SM8450 MDSS compatible
      phy: qcom: qmp-combo: Drop qmp_v4_calibrate_dp_phy
      phy: qcom: qmp-combo: Correct pre-emphasis table for QMP v4 DP PHYs
      arm64: defconfig: Add SM8450 camcc

 arch/arm64/boot/dts/qcom/sm8450.dtsi       | 50 ++++++------------------------
 arch/arm64/configs/defconfig               |  1 +
 drivers/clk/qcom/dispcc-sm8450.c           |  6 ++--
 drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c |  1 +
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c  | 33 +-------------------
 5 files changed, 16 insertions(+), 75 deletions(-)
---
base-commit: 948efecf22e49aa4bf55bb73ec79a0ddcfd38571
change-id: 20260622-sm8450-qol-466b8c07eb5f

Best regards,
--  
Esteban Urrutia <esteuwu@proton.me>

[PATCH 1/8] clk: qcom: dispcc-sm8450: Fix mdss clocks

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

Both of these changes allow the framebuffer to show upon boot and let
the mdss driver take over afterwards.
Before, none of these actions were possible. Only mdss takeover was
possible, but screen had to be turned off first.

OLE configuration may have been a misinterpretation... that's not
something that's done on the downstream driver.

Changing disp_cc_mdss_mdp_clk_src from clk_rcg2_shared_ops to
clk_rcg2_shared_no_init_park_ops fixes this warning as well:

[    0.075780] ------------[ cut here ]------------
[    0.075791] disp_cc_mdss_mdp_clk_src: rcg didn't update its configuration.
[    0.075812] WARNING: drivers/clk/qcom/clk-rcg2.c:136 at update_config+0xd4/0xe4, CPU#3: swapper/0/1
[    0.075840] Modules linked in:
[    0.075856] CPU: 3 UID: 0 PID: 1 Comm: swapper/0 Tainted: G S                  7.1.0-rc2+ #320 PREEMPT
[    0.075870] Tainted: [S]=CPU_OUT_OF_SPEC
[    0.075877] Hardware name: Motorola ThinkPhone by motorola (DT)
[    0.075887] pstate: 61400005 (nZCv daif +PAN -UAO -TCO +DIT -SSBS BTYPE=--)
[    0.075897] pc : update_config+0xd4/0xe4
[    0.075906] lr : update_config+0xd4/0xe4
[    0.075914] sp : ffff80008005b9f0
[    0.075921] x29: ffff80008005ba00 x28: 0000000000000004 x27: ffff000782892200
[    0.075937] x26: ffff0007823a46c0 x25: 0000000000000004 x24: ffffffffffffffff
[    0.075953] x23: ffff0007823a0240 x22: ffffdbc0a0940220 x21: ffffdbc0a0940220
[    0.075967] x20: ffffdbc0a0dcb388 x19: 0000000000000000 x18: 0000000000000048
[    0.075981] x17: 0000000000000014 x16: 0000000000010008 x15: fffffffffffea870
[    0.075996] x14: ffffdbc0a0c5d580 x13: ffffdbc0a0c5d600 x12: 00000000000001ee
[    0.076010] x11: fffffffffffea870 x10: fffffffffffea828 x9 : ffffdbc0a0c5d600
[    0.076024] x8 : 3fffffffffffefff x7 : ffffdbc0a0cb5600 x6 : 00000000000001ef
[    0.076038] x5 : 3ffffffffffff1ee x4 : 00000000000001ee x3 : 0000000000000000
[    0.076052] x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff00078066adc0
[    0.076067] Call trace:
[    0.076074]  update_config+0xd4/0xe4 (P)
[    0.076085]  clk_rcg2_shared_disable+0x50/0x80
[    0.076096]  clk_rcg2_shared_init+0x10/0x20
[    0.076107]  __clk_register+0x1b4/0x9ec
[    0.076118]  devm_clk_hw_register+0x5c/0xd4
[    0.076128]  devm_clk_register_regmap+0x44/0x84
[    0.076139]  qcom_cc_really_probe+0x304/0x514
[    0.076149]  disp_cc_sm8450_probe+0x104/0x200
[    0.076160]  platform_probe+0x5c/0xa4
[    0.076172]  really_probe+0xbc/0x2ac
[    0.076182]  __driver_probe_device+0x80/0x154
[    0.076193]  driver_probe_device+0x3c/0x184
[    0.076203]  __driver_attach+0x90/0x18c
[    0.076213]  bus_for_each_dev+0x7c/0xdc
[    0.076224]  driver_attach+0x24/0x30
[    0.076233]  bus_add_driver+0xe4/0x20c
[    0.076243]  driver_register+0x68/0x130
[    0.076251]  __platform_driver_register+0x20/0x2c
[    0.076260]  disp_cc_sm8450_driver_init+0x1c/0x28
[    0.076273]  do_one_initcall+0x60/0x1d4
[    0.076287]  kernel_init_freeable+0x24c/0x2d4
[    0.076299]  kernel_init+0x24/0x140
[    0.076311]  ret_from_fork+0x10/0x20
[    0.076323] ---[ end trace 0000000000000000 ]---

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 drivers/clk/qcom/dispcc-sm8450.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/clk/qcom/dispcc-sm8450.c b/drivers/clk/qcom/dispcc-sm8450.c
index 2e91332dd92a..b99d3eb5e195 100644
--- a/drivers/clk/qcom/dispcc-sm8450.c
+++ b/drivers/clk/qcom/dispcc-sm8450.c
@@ -614,7 +614,7 @@ static struct clk_rcg2 disp_cc_mdss_mdp_clk_src = {
 		.parent_data = disp_cc_parent_data_5,
 		.num_parents = ARRAY_SIZE(disp_cc_parent_data_5),
 		.flags = CLK_SET_RATE_PARENT,
-		.ops = &clk_rcg2_shared_ops,
+		.ops = &clk_rcg2_shared_no_init_park_ops,
 	},
 };
 
@@ -1824,8 +1824,8 @@ static int disp_cc_sm8450_probe(struct platform_device *pdev)
 		disp_cc_pll1.regs = clk_alpha_pll_regs[CLK_ALPHA_PLL_TYPE_LUCID_OLE];
 		disp_cc_pll1.clkr.hw.init = &sm8475_disp_cc_pll1_init;
 
-		clk_lucid_ole_pll_configure(&disp_cc_pll0, regmap, &sm8475_disp_cc_pll0_config);
-		clk_lucid_ole_pll_configure(&disp_cc_pll1, regmap, &sm8475_disp_cc_pll1_config);
+		clk_lucid_evo_pll_configure(&disp_cc_pll0, regmap, &sm8475_disp_cc_pll0_config);
+		clk_lucid_evo_pll_configure(&disp_cc_pll1, regmap, &sm8475_disp_cc_pll1_config);
 	} else {
 		clk_lucid_evo_pll_configure(&disp_cc_pll0, regmap, &disp_cc_pll0_config);
 		clk_lucid_evo_pll_configure(&disp_cc_pll1, regmap, &disp_cc_pll1_config);

-- 
2.54.0

[PATCH 2/8] arm64: dts: qcom: sm8450: Remove unneeded reserved memory nodes

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

These nodes are not present on downstream device trees and only take
memory away from the AP.
No crashes occur without these nodes, so remove them.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 15 ---------------
 1 file changed, 15 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 56cb6e959e4e..e34e3c05bf74 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -752,11 +752,6 @@ oem_vm_mem: memory@bb000000 {
 			no-map;
 		};
 
-		mte_mem: memory@c0000000 {
-			reg = <0x0 0xc0000000 0x0 0x20000000>;
-			no-map;
-		};
-
 		qheebsp_reserved_mem: memory@e0000000 {
 			reg = <0x0 0xe0000000 0x0 0x600000>;
 			no-map;
@@ -806,16 +801,6 @@ qtee_mem: memory@e9b00000 {
 			reg = <0x0 0xe9b00000 0x0 0x500000>;
 			no-map;
 		};
-
-		trusted_apps_mem: memory@ea000000 {
-			reg = <0x0 0xea000000 0x0 0x3900000>;
-			no-map;
-		};
-
-		trusted_apps_ext_mem: memory@ed900000 {
-			reg = <0x0 0xed900000 0x0 0x3b00000>;
-			no-map;
-		};
 	};
 
 	smp2p-adsp {

-- 
2.54.0

[PATCH 3/8] arm64: dts: qcom: sm8450: Modify GPU operating points

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

These frecuencies don't exist in downstream device trees.
Both 220MHz and 285MHz belong to SM8475, and I'm not sure where 317MHz
came from.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 15 ---------------
 1 file changed, 15 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index e34e3c05bf74..5e331a25e22a 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2495,21 +2495,6 @@ opp-350000000 {
 					opp-hz = /bits/ 64 <350000000>;
 					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
 				};
-
-				opp-317000000 {
-					opp-hz = /bits/ 64 <317000000>;
-					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS>;
-				};
-
-				opp-285000000 {
-					opp-hz = /bits/ 64 <285000000>;
-					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
-				};
-
-				opp-220000000 {
-					opp-hz = /bits/ 64 <220000000>;
-					opp-level = <RPMH_REGULATOR_LEVEL_LOW_SVS_D1>;
-				};
 			};
 		};
 

-- 
2.54.0

[PATCH 4/8] arm64: dts: qcom: sm8450: Add missing PCM_OUT port

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

An error in dmesg shows there is a mismatch between controller and DT
dout-ports.
Add PCM_OUT port to fix this.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 arch/arm64/boot/dts/qcom/sm8450.dtsi | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)

diff --git a/arch/arm64/boot/dts/qcom/sm8450.dtsi b/arch/arm64/boot/dts/qcom/sm8450.dtsi
index 5e331a25e22a..8fc58a02e5c5 100644
--- a/arch/arm64/boot/dts/qcom/sm8450.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm8450.dtsi
@@ -2914,20 +2914,20 @@ swr1: soundwire@3210000 {
 			clock-names = "iface";
 			label = "RX";
 			qcom,din-ports = <0>;
-			qcom,dout-ports = <5>;
+			qcom,dout-ports = <6>;
 
 			pinctrl-0 = <&rx_swr_active>;
 			pinctrl-names = "default";
 
-			qcom,ports-sinterval-low =	/bits/ 8 <0x03 0x1f 0x1f 0x07 0x00>;
-			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x00>;
-			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00>;
-			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff>;
-			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff>;
-			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff>;
-			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff>;
-			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00>;
-			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00>;
+			qcom,ports-sinterval =		/bits/ 16 <0x03 0x3f 0x1f 0x07 0x00 0x18f>;
+			qcom,ports-offset1 =		/bits/ 8 <0x00 0x00 0x0b 0x01 0x00 0x00>;
+			qcom,ports-offset2 =		/bits/ 8 <0x00 0x00 0x0b 0x00 0x00 0x00>;
+			qcom,ports-hstart =		/bits/ 8 <0xff 0x03 0xff 0xff 0xff 0x08>;
+			qcom,ports-hstop =		/bits/ 8 <0xff 0x06 0xff 0xff 0xff 0x08>;
+			qcom,ports-word-length =	/bits/ 8 <0x01 0x07 0x04 0xff 0xff 0x0f>;
+			qcom,ports-block-pack-mode =	/bits/ 8 <0xff 0x00 0x01 0xff 0xff 0x00>;
+			qcom,ports-block-group-count =	/bits/ 8 <0xff 0xff 0xff 0xff 0x00 0x00>;
+			qcom,ports-lane-control =	/bits/ 8 <0x01 0x00 0x00 0x00 0x00 0x00>;
 
 			#address-cells = <2>;
 			#size-cells = <0>;

-- 
2.54.0

[PATCH 5/8] iommu/arm-smmu-qcom: Add SM8450 MDSS compatible

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

Add the compatible for the MDSS client on the Snapdragon 8 Gen 1 so it
can be properly configured by the IOMMU driver.

Otherwise, there is an unhandled context fault.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
index e2c914fccd6f..795e8ec7e8fa 100644
--- a/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
+++ b/drivers/iommu/arm/arm-smmu/arm-smmu-qcom.c
@@ -425,6 +425,7 @@ static const struct of_device_id qcom_smmu_client_of_match[] __maybe_unused = {
 	{ .compatible = "qcom,sm6375-mdss" },
 	{ .compatible = "qcom,sm8150-mdss" },
 	{ .compatible = "qcom,sm8250-mdss" },
+	{ .compatible = "qcom,sm8450-mdss" },
 	{ .compatible = "qcom,x1e80100-mdss" },
 	{ }
 };

-- 
2.54.0

[PATCH 6/8] phy: qcom: qmp-combo: Drop qmp_v4_calibrate_dp_phy

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

There are no downstream device trees that specify five values in the
qcom,aux-cfg1-settings array.
Plus, after cross referencing both downstream device trees and entries
which refer this function, only 0x13 is specified.
Since 0x13 is written at initialization time, drop this function as a
whole, and remove now unused variable assignations.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 31 -------------------------------
 1 file changed, 31 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index cdcfad2e86b1..9bd666ac2c49 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -2325,7 +2325,6 @@ static int qmp_v3_calibrate_dp_phy(struct qmp_combo *qmp);
 static void qmp_v4_dp_aux_init(struct qmp_combo *qmp);
 static void qmp_v4_configure_dp_tx(struct qmp_combo *qmp);
 static int qmp_v4_configure_dp_phy(struct qmp_combo *qmp);
-static int qmp_v4_calibrate_dp_phy(struct qmp_combo *qmp);
 
 static void qmp_v8_dp_aux_init(struct qmp_combo *qmp);
 static int qmp_v8_configure_dp_clocks(struct qmp_combo *qmp);
@@ -2466,7 +2465,6 @@ static const struct qmp_phy_cfg sar2130p_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.regs			= qmp_v6_usb3phy_regs_layout,
 	.reset_list		= msm8996_usb3phy_reset_l,
@@ -2603,7 +2601,6 @@ static const struct qmp_phy_cfg sc8180x_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.reset_list		= msm8996_usb3phy_reset_l,
 	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
@@ -2650,7 +2647,6 @@ static const struct qmp_phy_cfg sc8280xp_usb43dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.reset_list		= msm8996_usb3phy_reset_l,
 	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
@@ -2696,7 +2692,6 @@ static const struct qmp_phy_cfg x1e80100_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.reset_list		= msm8996_usb3phy_reset_l,
 	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
@@ -2785,7 +2780,6 @@ static const struct qmp_phy_cfg sm8250_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.reset_list		= msm8996_usb3phy_reset_l,
 	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
@@ -2834,7 +2828,6 @@ static const struct qmp_phy_cfg sm8350_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.reset_list		= msm8996_usb3phy_reset_l,
 	.num_resets		= ARRAY_SIZE(msm8996_usb3phy_reset_l),
@@ -2882,7 +2875,6 @@ static const struct qmp_phy_cfg sm8550_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.regs			= qmp_v6_usb3phy_regs_layout,
 	.reset_list		= msm8996_usb3phy_reset_l,
@@ -2928,7 +2920,6 @@ static const struct qmp_phy_cfg sm8650_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.regs			= qmp_v6_usb3phy_regs_layout,
 	.reset_list		= msm8996_usb3phy_reset_l,
@@ -2974,7 +2965,6 @@ static const struct qmp_phy_cfg sm8750_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v3_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v4_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.regs			= qmp_v8_usb3phy_regs_layout,
 	.reset_list		= msm8996_usb3phy_reset_l,
@@ -3020,7 +3010,6 @@ static const struct qmp_phy_cfg glymur_usb3dpphy_cfg = {
 	.configure_dp_tx	= qmp_v4_configure_dp_tx,
 	.configure_dp_clocks	= qmp_v8_configure_dp_clocks,
 	.configure_dp_phy	= qmp_v8_configure_dp_phy,
-	.calibrate_dp_phy	= qmp_v4_calibrate_dp_phy,
 
 	.regs			= qmp_v8_n3_usb43dpphy_regs_layout,
 	.reset_list		= msm8996_usb3phy_reset_l,
@@ -3316,7 +3305,6 @@ static void qmp_v4_dp_aux_init(struct qmp_combo *qmp)
 	writel(0x03, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG7);
 	writel(0xb7, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG8);
 	writel(0x03, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG9);
-	qmp->dp_aux_cfg = 0;
 
 	writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK |
 	       PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK |
@@ -3345,7 +3333,6 @@ static void qmp_v8_dp_aux_init(struct qmp_combo *qmp)
 	writel(0x03, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG7);
 	writel(0xb7, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG8);
 	writel(0x03, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG9);
-	qmp->dp_aux_cfg = 0;
 
 	writel(PHY_AUX_STOP_ERR_MASK | PHY_AUX_DEC_ERR_MASK |
 	       PHY_AUX_SYNC_ERR_MASK | PHY_AUX_ALIGN_ERR_MASK |
@@ -3605,24 +3592,6 @@ static int qmp_v8_configure_dp_phy(struct qmp_combo *qmp)
 	return 0;
 }
 
-/*
- * We need to calibrate the aux setting here as many times
- * as the caller tries
- */
-static int qmp_v4_calibrate_dp_phy(struct qmp_combo *qmp)
-{
-	static const u8 cfg1_settings[] = { 0x20, 0x13, 0x23, 0x1d };
-	u8 val;
-
-	qmp->dp_aux_cfg++;
-	qmp->dp_aux_cfg %= ARRAY_SIZE(cfg1_settings);
-	val = cfg1_settings[qmp->dp_aux_cfg];
-
-	writel(val, qmp->dp_dp_phy + QSERDES_DP_PHY_AUX_CFG1);
-
-	return 0;
-}
-
 static int qmp_combo_dp_configure(struct phy *phy, union phy_configure_opts *opts)
 {
 	const struct phy_configure_opts_dp *dp_opts = &opts->dp;

-- 
2.54.0

[PATCH 7/8] phy: qcom: qmp-combo: Correct pre-emphasis table for QMP v4 DP PHYs

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

Comparing sm8350 and sm8450 tables, this seems to be typo.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 drivers/phy/qualcomm/phy-qcom-qmp-combo.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
index 9bd666ac2c49..5b278fd54a16 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp-combo.c
@@ -2108,7 +2108,7 @@ static const u8 qmp_dp_v4_pre_emphasis_hbr3_hbr2[4][4] = {
 static const u8 qmp_dp_v4_pre_emphasis_hbr_rbr[4][4] = {
 	{ 0x00, 0x0d, 0x14, 0x1a },
 	{ 0x00, 0x0e, 0x15, 0xff },
-	{ 0x00, 0x0d, 0xff, 0xff },
+	{ 0x00, 0x0e, 0xff, 0xff },
 	{ 0x03, 0xff, 0xff, 0xff }
 };
 

-- 
2.54.0

[PATCH 8/8] arm64: defconfig: Add SM8450 camcc

[Esteban Urrutia via B4 Relay]

From: Esteban Urrutia <esteuwu@proton.me>

Add SM8450 camcc as a module since it's enabled in SM8450 dtsi.

Signed-off-by: Esteban Urrutia <esteuwu@proton.me>
---
 arch/arm64/configs/defconfig | 1 +
 1 file changed, 1 insertion(+)

diff --git a/arch/arm64/configs/defconfig b/arch/arm64/configs/defconfig
index f2e6ae93e533..8c50c16ee0b8 100644
--- a/arch/arm64/configs/defconfig
+++ b/arch/arm64/configs/defconfig
@@ -1541,6 +1541,7 @@ CONFIG_SDX_GCC_75=y
 CONFIG_SM_CAMCC_6350=m
 CONFIG_SM_CAMCC_MILOS=m
 CONFIG_SM_CAMCC_8250=m
+CONFIG_SM_CAMCC_8450=m
 CONFIG_SM_CAMCC_8550=m
 CONFIG_SM_CAMCC_8650=m
 CONFIG_SM_CAMCC_8750=m

-- 
2.54.0

Re: [PATCH 8/8] arm64: defconfig: Add SM8450 camcc

[Krzysztof Kozlowski]

On 23/06/2026 02:54, Esteban Urrutia via B4 Relay wrote:
> From: Esteban Urrutia <esteuwu@proton.me>
> 
> Add SM8450 camcc as a module since it's enabled in SM8450 dtsi.


This is not needed. I already sent such patch.

Best regards,
Krzysztof