* [PATCH 06/13] mfd: twl-core: Add initial DT support for twl4030/twl6030
From: Cousson, Benoit @ 2011-09-28 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <4E816232.5020502@ti.com>
On 9/27/2011 7:42 AM, Nayak, Rajendra wrote:
> On Monday 26 September 2011 10:20 PM, Benoit Cousson wrote:
>> Add initial device-tree support for twl familly chips.
>
> s/familly/family
Oops.
>> The current version is missing the regulator entries due
>> to the lack of DT regulator bindings for the moment.
>> Only the simple sub-modules that do not depend on
>> platform_data information can be initialized properly.
>>
>> Add documentation for the Texas Instruments TWL Integrated Chip.
>>
>> Signed-off-by: Benoit Cousson<b-cousson@ti.com>
>> Cc: Balaji T K<balajitk@ti.com>
>> Cc: Graeme Gregory<gg@slimlogic.co.uk>
>> Cc: Samuel Ortiz<sameo@linux.intel.com>
>> ---
>> .../devicetree/bindings/mfd/twl-familly.txt | 47 +++++++++++++++++
>> drivers/mfd/twl-core.c | 53 ++++++++++++++++++--
>> 2 files changed, 96 insertions(+), 4 deletions(-)
>> create mode 100644 Documentation/devicetree/bindings/mfd/twl-familly.txt
>
> s/familly.txt/family.txt
At least I am consistent in my typos ;-)
>> diff --git a/Documentation/devicetree/bindings/mfd/twl-familly.txt b/Documentation/devicetree/bindings/mfd/twl-familly.txt
>> new file mode 100644
>> index 0000000..ff4cacd
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/mfd/twl-familly.txt
>> @@ -0,0 +1,47 @@
>> +Texas Instruments TWL family
>> +
>> +The TWLs are Integrated Power Management Chips.
>> +Some version might contain much more analog function like
>> +USB transceiver or Audio amplifier.
>> +These chips are connected to an i2c bus.
>> +
>> +
>> +Required properties:
>> +- compatible : Must be "ti,twl4030";
>> + For Integrated power-management/audio CODEC device used in OMAP3
>> + based boards
>> +- compatible : Must be "ti,twl6030";
>> + For Integrated power-management used in OMAP4 based boards
>> +- interrupts : This i2c device has an IRQ line connected to the main SoC
>> +- interrupt-controller : Since the twl support several interrupts internally,
>> + it is considered as an interrupt controller cascaded to the SoC one.
>> +- #interrupt-cells =<1>;
>> +- interrupt-parent : The parent interrupt controller.
>> +
>> +Optional node:
>> +- Child nodes contain in the twl. The twl family is made of severals variants
>> + that support a different number of features.
>> + The children nodes will thus depend of the capabilty of the variant.
>> +
>> +
>> +Example:
>> +/*
>> + * Integrated Power Management Chip
>> + * http://www.ti.com/lit/ds/symlink/twl6030.pdf
>> + */
>> +twl at 48 {
>> + compatible = "ti,twl6030";
>> + reg =<0x48>;
>
> What does the 'reg' property signify here for twl?
The i2c slave address.
>> + interrupts =<39>; /* IRQ_SYS_1N cascaded to gic */
>> + interrupt-controller;
>> + #interrupt-cells =<1>;
>> + interrupt-parent =<&gic>;
>> + #address-cells =<1>;
>> + #size-cells =<0>;
>> +
>> + twl_rtc {
>> + compatible = "ti,twl_rtc";
>> + interrupts =<11>;
>> + reg =<0>;
>
> Does the 'reg' property need to be faked for
> every twl child node, even if it does not have
> any?
No, it was even removed from the DTS. But I forgot to update the
documentation:-(
>> + };
>> +};
>> diff --git a/drivers/mfd/twl-core.c b/drivers/mfd/twl-core.c
>> index 01ecfee..3ef0b43 100644
>> --- a/drivers/mfd/twl-core.c
>> +++ b/drivers/mfd/twl-core.c
>> @@ -33,6 +33,10 @@
>> #include<linux/platform_device.h>
>> #include<linux/clk.h>
>> #include<linux/err.h>
>> +#include<linux/slab.h>
>> +#include<linux/of_irq.h>
>> +#include<linux/of_platform.h>
>> +#include<linux/irqdomain.h>
>>
>> #include<linux/regulator/machine.h>
>>
>> @@ -1182,22 +1186,53 @@ twl_probe(struct i2c_client *client, const struct i2c_device_id *id)
>> int status;
>> unsigned i;
>> struct twl4030_platform_data *pdata = client->dev.platform_data;
>> + struct device_node *node = client->dev.of_node;
>> u8 temp;
>> int ret = 0;
>>
>> + if (node&& !pdata) {
>> + /*
>> + * XXX: Temporary fake pdata until the information
>> + * is correctly retrieved by every TWL modules from DT.
>> + */
>> + pdata = kzalloc(sizeof(struct twl4030_platform_data),
>> + GFP_KERNEL);
>
> devm_kzalloc instead?
Good point.
>> + if (!pdata) {
>> + status = -ENOMEM;
>> + goto exit;
>> + }
>> +
>> + /*
>> + * XXX: For the moment the IRQs for TWL seems to be encoded in
>> + * the global OMAP space. That should be cleaned to allow
>> + * dynamically adding a new IRQ controller.
>> + */
>> + if ((id->driver_data)& TWL6030_CLASS) {
>> + pdata->irq_base = TWL6030_IRQ_BASE;
>> + pdata->irq_end = pdata->irq_base + TWL6030_BASE_NR_IRQS;
>> + } else {
>> + pdata->irq_base = TWL4030_IRQ_BASE;
>> + pdata->irq_end = pdata->irq_base + TWL4030_BASE_NR_IRQS;
>> + }
>> + irq_domain_add_simple(node, pdata->irq_base);
>> + }
>> +
>> if (!pdata) {
>> dev_dbg(&client->dev, "no platform data?\n");
>> - return -EINVAL;
>> + status = -EINVAL;
>> + goto fail_free;
>> }
>>
>> if (i2c_check_functionality(client->adapter, I2C_FUNC_I2C) == 0) {
>> dev_dbg(&client->dev, "can't talk I2C?\n");
>> - return -EIO;
>> + status = -EIO;
>> + goto fail_free;
>> }
>>
>> if (inuse) {
>> dev_dbg(&client->dev, "driver is already in use\n");
>> - return -EBUSY;
>> + status = -EBUSY;
>> + goto fail_free;
>> }
>>
>> for (i = 0; i< TWL_NUM_SLAVES; i++) {
>> @@ -1269,10 +1304,20 @@ twl_probe(struct i2c_client *client, const struct i2c_device_id *id)
>> twl_i2c_write_u8(TWL4030_MODULE_INTBR, temp, REG_GPPUPDCTR1);
>> }
>>
>> - status = add_children(pdata, id->driver_data);
>> +#ifdef CONFIG_OF_DEVICE
>
> is the #ifdef really needed?
Yes, because the of_platform_populate does not have a stub in case of
none DT build... But I agree, it is ugly and the of_platform.h should
maybe be fixed instead.
I was too lazy to fix it :-)
Thanks,
Benoit
^ permalink raw reply
* [linux-pm Query] Power Management Device Suspend/ Resume
From: Vinod Koul @ 2011-09-28 8:54 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <4E82C294.7000308@st.com>
On Wed, 2011-09-28 at 12:15 +0530, Viresh Kumar wrote:
> Vinod,
>
> Thanks for mailing us back.
>
> On 9/28/2011 9:12 AM, Vinod Koul wrote:
> > On Wed, 2011-09-28 at 08:55 +0530, Viresh Kumar wrote:
> >> On 9/22/2011 4:19 PM, Deepak Sikri wrote:
> > are you trying to do runtime power management or traditional suspend and
> > resume? IMO both should be done...
>
> We will first be testing traditional suspend/resume, but obviously we would
> try to design drivers in order to support runtime PM too.
>
> >>> *Query- 1*. Suppose my platform has a ADC driver under char framework, which internally uses the
> >>> DMA driver (channels). Now, ADC driver can be used by other kernel drivers or directly from user application.
> >>>
> >>> *1. a.* What are the expectations from the suspend and resume routines of both the devices, DMA & ADC ?
> >>>
> >>> */-- Given that few of the options are/*
> >>> */1.a.1. On suspend,/*
> >>> In ADC suspend function: ADC releases all the DMA channels, latches its registers; and
> >>> DMA suspend function: DMA does nothing except for lataching of registers if required.
> >>>
> >>> */1.a.2. On suspend, /*
> >>> ADC suspend function: ADC just latches its registers and stops R/W through DMA, no DMA channel release;
> >>> DMA suspend function: DMA halts its operating channels, and latches its registers if required.
> > Well channel release/alloc is not really required. You can goto suspend
> > in between as well. if you have queued but not active descriptors on all
> > channels then dmac is idle and you can use this time to goto suspend.
>
> But the time suspend is called for DMA, we may in middle of DMA transfers
> on few channels. So should we wait for them to finish or simply disable
> channel transfer? And in case of resume what will happen to transfers that
> were active during suspend?
In traditional suspend, you should pause the channel, go to suspend.
Basically any active work needs to paused while you suspend to disk/ram.
But in case of embedded devices I would be surprised to see this even
being the case.
>
> >>> *1.b* Will the suspend resume for the dependent drivers follow sequencing, i.e. Suspend of ADC followed by
> >>> Suspend of DMA? (Assume both of these devices are hooked on to Platform bus, given that ADC uses DMA)
> > why do you care?
>
> Suppose suspend of DMA occurs first and we disable its clock in the suspend
> routine. Now before the suspend of ADC is called, ADC requests for DMA
> transfers and because not every routine of DMA keeps track of clk is on/off,
> it may try to access DMA register.
>
> So, we must ensure that all children are suspended before the parent is
> requested to suspend. And probably this is the correct way.
> So, here we need ADC to suspend before DMA. How is this sequencing ensured?
No your driver should handle it well
Btw if you do runtime_pm implementation first, things will be lot easier
for you
> >>> 2.1 The user space threads freeze first followed by kernel space. In case the user space process issues a a system
> >>> call (lets assume an ioctl system call), how will the user space thread respond in case of suspend to ram?
> > all user space processes are frozen on STR
>
> Yes, but what will be its state. Will the system calls complete? Will it
> close all devices opened by it before freezing?
See the talks by Rafael in various conferences, they have lot of info
covering these questions.
IMO all processes are frozen on traditional suspend and later thawed on
resume.
>
> Suppose a user applications is accessing few ADC channels. ADC controller
> and its channel are all configured. Now, suspend is requested. What should
> ADC driver do? As power will be turned off, its register will loose their
> value.
It need to pause/stop current operation or return EBUSY/EAGAIN. Btw does
it happen for you while system is trying to do suspend.
>
> Should ADC reconfigure all its channel registers by keeping their state?
> Also it is not very straight forward to reconfigure channels directly, as
> registers are required to be programmed in certain sequence, so there
> needs to be good amount of intelligence put into driver for that.
yup, you should be doing that on device probe anyway
>
> IIRC, i couldn't find any such stuff in other mainline drivers. And that's
> why we are confused on this topic.
--
~Vinod
^ permalink raw reply
* [PATCH v3 4/6] arm/imx6q: add smp and cpu hotplug support
From: Shawn Guo @ 2011-09-28 8:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20110928062945.GC14191@pengutronix.de>
On Wed, Sep 28, 2011 at 08:29:45AM +0200, Sascha Hauer wrote:
> On Tue, Sep 27, 2011 at 11:15:47PM +0800, Shawn Guo wrote:
> > >
> > > I do not want to add mxc_cpu_type and cpu_is_mx6q() stuff, so I intend
> > > to remove early_initcall there, and let imx31/35_soc_init() explicitly
> > > calls mxc_init_l2x0().
> > >
> > I'm changing my mind (so quickly). It turns out we will fall into a
> > number of other traps if we build imx6q with imx3 without mxc_cpu_type
> > set up for imx6q, arch_idle(), __imx_ioremap(), etc. So for now, I
> > want to add mxc_cpu_type for imx6q to cooperate with all these traps.
>
> I'm fine with reducing the usage of cpu_is_* macros up to the point when
> we don't need them anymore. But as you already found out, it's better to
> do this seperately.
>
I'm changing my mind again. I decided to clean up these traps with a
patch series, which I'm sending right now.
--
Regards,
Shawn
^ permalink raw reply
* [PATCH V2 1/1] dmaengine/amba-pl08x: Add support for s3c64xx DMAC
From: Alim Akhtar @ 2011-09-28 8:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CACRpkdZesKGuPGmUifLj4puN_e=kYAb4WyuQs+xERn9q7036rg@mail.gmail.com>
HI Linus,
Thanks for reviewing again.
On Wed, Sep 28, 2011 at 1:31 PM, Linus Walleij <linus.walleij@linaro.org> wrote:
> Sorry if I missed a few nitpicks last time, anyway it's looking much better now:
>
> On Wed, Sep 28, 2011 at 7:50 AM, Alim Akhtar <alim.akhtar@samsung.com> wrote:
>> + ? ? ? /*
>> + ? ? ? ?* Samsung pl080 DMAC has one exrta control register
>
> s/exrta/exstra
>
I will correct this.
>> + ? ? ? if (pl08x->vd->is_pl080_s3c) {
>> + ? ? ? ? ? ? ? writel(txd->ccfg, phychan->base + PL080S_CH_CONFIG);
>> + ? ? ? ? ? ? ? writel(lli->cctl1, phychan->base + PL080S_CH_CONTROL2);
>> + ? ? ? } else
>> + ? ? ? ? ? ? ? writel(txd->ccfg, phychan->base + PL080_CH_CONFIG);
>
> What do you think about adding a field to the struct pl08x
> like
>
> u32 config_reg
>
> that we set to the proper config register (PL080S_CH_CONFIG or
> PL080_CH_CONFIG in probe(), so the above
> becomes the simpler variant:
>
> writel(txd->ccfg, phychan->base + pl08x->config_reg);
> if (pl08x->vd->is_pl080_s3c)
> ? ?writel(lli->cctl1, phychan->base + PL080S_CH_CONTROL2);
>
I will try implement this way or as viresh has pointed out to remove
the code duplications.
>> + ? ? ? if (pl08x->vd->is_pl080_s3c) {
>> + ? ? ? ? ? ? ? val = readl(phychan->base + PL080S_CH_CONFIG);
>> + ? ? ? ? ? ? ? while ((val & PL080_CONFIG_ACTIVE) ||
>> + ? ? ? ? ? ? ? ? ? ? ? (val & PL080_CONFIG_ENABLE))
>> + ? ? ? ? ? ? ? ? ? ? ? val = readl(phychan->base + PL080S_CH_CONFIG);
>> +
>> + ? ? ? ? ? ? ? writel(val | PL080_CONFIG_ENABLE,
>> + ? ? ? ? ? ? ? ? ? ? ? phychan->base + PL080S_CH_CONFIG);
>> + ? ? ? } else {
>> ? ? ? ? ? ? ? ?val = readl(phychan->base + PL080_CH_CONFIG);
>> + ? ? ? ? ? ? ? ? ? ? ? while ((val & PL080_CONFIG_ACTIVE) ||
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? (val & PL080_CONFIG_ENABLE))
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? val = readl(phychan->base + PL080_CH_CONFIG);
>>
>> - ? ? ? writel(val | PL080_CONFIG_ENABLE, phychan->base + PL080_CH_CONFIG);
>> + ? ? ? ? ? ? ? writel(val | PL080_CONFIG_ENABLE,
>> + ? ? ? ? ? ? ? ? ? ? ? phychan->base + PL080_CH_CONFIG);
>> + ? ? ? }
>
> This would also become much simpler with that approach I think...
>
OK, i will do that.
>> ? ? ? ?/* Set the HALT bit and wait for the FIFO to drain */
>> - ? ? ? val = readl(ch->base + PL080_CH_CONFIG);
>> - ? ? ? val |= PL080_CONFIG_HALT;
>> - ? ? ? writel(val, ch->base + PL080_CH_CONFIG);
>> -
>> + ? ? ? if (pl08x->vd->is_pl080_s3c) {
>> + ? ? ? ? ? ? ? val = readl(ch->base + PL080S_CH_CONFIG);
>> + ? ? ? ? ? ? ? val |= PL080_CONFIG_HALT;
>> + ? ? ? ? ? ? ? writel(val, ch->base + PL080S_CH_CONFIG);
>> + ? ? ? } else {
>> + ? ? ? ? ? ? ? val = readl(ch->base + PL080_CH_CONFIG);
>> + ? ? ? ? ? ? ? val |= PL080_CONFIG_HALT;
>> + ? ? ? ? ? ? ? writel(val, ch->base + PL080_CH_CONFIG);
>> + ? ? ? }
>
> This would become simply:
>
> val = readl(ch->base + pl08x->config_reg);
> val |= PL080_CONFIG_HALT;
> writel(val, ch->base + pl08x->config_reg);
>
>
ok, i will do that.
>> ? ? ? ?/* Clear the HALT bit */
>> - ? ? ? val = readl(ch->base + PL080_CH_CONFIG);
>> - ? ? ? val &= ~PL080_CONFIG_HALT;
>> - ? ? ? writel(val, ch->base + PL080_CH_CONFIG);
>> + ? ? ? if (pl08x->vd->is_pl080_s3c) {
>> + ? ? ? ? ? ? ? val = readl(ch->base + PL080S_CH_CONFIG);
>> + ? ? ? ? ? ? ? val &= ~PL080_CONFIG_HALT;
>> + ? ? ? ? ? ? ? writel(val, ch->base + PL080S_CH_CONFIG);
>> + ? ? ? } else {
>> + ? ? ? ? ? ? ? val = readl(ch->base + PL080_CH_CONFIG);
>> + ? ? ? ? ? ? ? val &= ~PL080_CONFIG_HALT;
>> + ? ? ? ? ? ? ? writel(val, ch->base + PL080_CH_CONFIG);
>> + ? ? ? }
>
> This would get rid of the if/else clauses
>
ok, understand
>> + ? ? ? if (pl08x->vd->is_pl080_s3c) {
>> + ? ? ? ? ? ? ? u32 val = readl(ch->base + PL080S_CH_CONFIG);
>> + ? ? ? ? ? ? ? val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? PL080_CONFIG_TC_IRQ_MASK);
>> + ? ? ? ? ? ? ? writel(val, ch->base + PL080S_CH_CONFIG);
>> + ? ? ? } else {
>> + ? ? ? ? ? ? ? u32 val = readl(ch->base + PL080_CH_CONFIG);
>> + ? ? ? ? ? ? ? val &= ~(PL080_CONFIG_ENABLE | PL080_CONFIG_ERR_IRQ_MASK |
>> + ? ? ? ? ? ? ? ? ? ? ? ? ? ? ? PL080_CONFIG_TC_IRQ_MASK);
>> + ? ? ? ? ? ? ? writel(val, ch->base + PL080_CH_CONFIG);
>> + ? ? ? }
>
> As would this...
>
>> + ? ? ? /* Samsung DMAC is PL080 variant*/
>> + ? ? ? {
>> + ? ? ? ? ? ? ? .id ? ? = 0x00041082,
>> + ? ? ? ? ? ? ? .mask ? = 0x000fffff,
>> + ? ? ? ? ? ? ? .data ? = &vendor_pl080_s3c,
>
> Does the hardware realy have this primecell number or is it something that is
> hardcoded from the board/device tree?
>
It is a hardcoded value as s3c64xx does not have Identification registers.
> If it is hardcoded then no objections.
>
> In the latter case, replace 0x41 (= 'A', ARM) with something like
> 0x55 'U' for Samsung or so. Or 0x51 'S'. Or whatever you like.
>
> Then add that to include/linux/amba/bus.h as
> AMBA_VENDOR_SAMSUNG = 0x55,
> so we have this under some kind of control.
>
> Yours,
> Linus Walleij
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>
--
aLim akHtaR
mAin hUn nA :-)
^ permalink raw reply
* [RFC] Shrink sched_clock some more
From: Linus Walleij @ 2011-09-28 8:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20110922153611.GC8072@n2100.arm.linux.org.uk>
On Thu, Sep 22, 2011 at 5:36 PM, Russell King - ARM Linux
<linux@arm.linux.org.uk> wrote:
> ... by getting rid of the fixed-constant optimization, and moving the
> update code into arch/arm/kernel/sched_clock.c.
>
> Platforms now only have to supply a function to read the sched_clock
> register, and some basic information such as the number of significant
> bits and the tick rate.
>
> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
I really like the looks of this patch!
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Yours,
Linus Walleij
^ permalink raw reply
* [PATCH 1/3] mmc: mmci: Put power register deviations in variant data
From: Sebastian RASMUSSEN @ 2011-09-28 9:05 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CACRpkdZoXmQiUJbLkzgTkRnjukS18RvcZASXzZshnuDSQDE1aQ@mail.gmail.com>
> > + ? ? ? unsigned int ? ? ? ? ? ?pwrreg_powerup;
>
> This should probably be u32, no big deal but easy to fix.
> Can be done when putting it into Russells patch tracker I guess.
Agreed, since pwr is u32 where pwrreg is used, it should be.
/ Sebastian
^ permalink raw reply
* [PATCH v4 0/7] add initial imx6q support
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
This patch series adds the initial support for imx6q, which is a
Cortex-A9 Quad Core based SoC.
We chose to add imx6q support into mach-imx other than mach-mx5 or
a new mach-mx6, because we intend to merge mach-mx5 into mach-imx, so
that we have only mach-imx for imx family.
It's based on linux-next-20110926 with some prerequisite patches
not showing up on linux-next applied.
Changes since v3:
* Fold the gic_handle_irq (local to imx) support patch in the series.
It can be replaced by Marc Zyngier's global gic_handle_irq support
with a little rework if his PPI and MULTI_IRQ_HANDLER series gets
merged.
Changes since v2:
* Refine the L2 register save/restore implementation per Lorenzo's
suggestion
* Rebase to Rob's latest GIC OF bindings series
* Rebase to Sascha's MULTI_IRQ_HANDLER support series
Changes since v1:
* Use the existing IMX_IO_P2V for static mapping
* Fix the MXC_INTERNAL_IRQS breakage introduced by GIC definition
* Retrieve clock frequency for fixed clocks from device tree
* Drop early_initcall from imx_src_init() and call it from imx6q
platform initialization
* Use readl_relaxed/writel_relaxed rather than __raw_readl/__raw_writel
as suggested by Arnd
* Kill unnecessary imx_local_timer_pre_suspend/resume functions
* Kill Kconfig symbol MACH_IMX6Q
* Rebase to rmk's "Add L2 cache cleaning to generic CPU suspend" series
so that we can retain L2 cache with necessary L2 register
save/restore across suspend/resume cycle
* Rebase to Rob's new "GIC OF bindings" series
Thanks.
Shawn Guo (7):
arm/imx6q: add device tree source
arm/imx6q: add core definitions and low-level debug uart
arm/imx: add gic_handle_irq function
arm/imx6q: add core drivers clock, gpc, mmdc and src
arm/imx6q: add smp and cpu hotplug support
arm/imx6q: add device tree machine support
arm/imx6q: add suspend/resume support
Documentation/devicetree/bindings/arm/fsl.txt | 6 +
arch/arm/Kconfig | 2 +-
arch/arm/Kconfig.debug | 7 +
arch/arm/Makefile | 1 +
arch/arm/boot/dts/imx6q-sabreauto.dts | 82 +
arch/arm/boot/dts/imx6q.dtsi | 555 +++++++
arch/arm/mach-imx/Kconfig | 28 +
arch/arm/mach-imx/Makefile | 11 +
arch/arm/mach-imx/Makefile.boot | 4 +
arch/arm/mach-imx/clock-imx6q.c | 2012 +++++++++++++++++++++++++
arch/arm/mach-imx/gpc.c | 113 ++
arch/arm/mach-imx/head-v7.S | 103 ++
arch/arm/mach-imx/hotplug.c | 44 +
arch/arm/mach-imx/lluart.c | 32 +
arch/arm/mach-imx/localtimer.c | 35 +
arch/arm/mach-imx/mach-imx6q.c | 84 +
arch/arm/mach-imx/mmdc.c | 72 +
arch/arm/mach-imx/platsmp.c | 85 ++
arch/arm/mach-imx/pm-imx6q.c | 90 ++
arch/arm/mach-imx/src.c | 49 +
arch/arm/mm/Kconfig | 2 +-
arch/arm/plat-mxc/Kconfig | 7 +
arch/arm/plat-mxc/Makefile | 2 +-
arch/arm/plat-mxc/gic.c | 47 +
arch/arm/plat-mxc/include/mach/common.h | 29 +
arch/arm/plat-mxc/include/mach/debug-macro.S | 2 +
arch/arm/plat-mxc/include/mach/entry-macro.S | 6 +
arch/arm/plat-mxc/include/mach/hardware.h | 6 +
arch/arm/plat-mxc/include/mach/irqs.h | 10 +-
arch/arm/plat-mxc/include/mach/memory.h | 1 +
arch/arm/plat-mxc/include/mach/mx6q.h | 33 +
31 files changed, 3555 insertions(+), 5 deletions(-)
^ permalink raw reply
* [PATCH v4 1/7] arm/imx6q: add device tree source
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
It adds device tree source and documentation for imx6q platform.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
Documentation/devicetree/bindings/arm/fsl.txt | 6 +
arch/arm/boot/dts/imx6q-sabreauto.dts | 82 ++++
arch/arm/boot/dts/imx6q.dtsi | 555 +++++++++++++++++++++++++
3 files changed, 643 insertions(+), 0 deletions(-)
create mode 100644 Documentation/devicetree/bindings/arm/fsl.txt
create mode 100644 arch/arm/boot/dts/imx6q-sabreauto.dts
create mode 100644 arch/arm/boot/dts/imx6q.dtsi
diff --git a/Documentation/devicetree/bindings/arm/fsl.txt b/Documentation/devicetree/bindings/arm/fsl.txt
new file mode 100644
index 0000000..345bfc0
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/fsl.txt
@@ -0,0 +1,6 @@
+Freescale i.MX Platforms Device Tree Bindings
+-----------------------------------------------
+
+i.MX6 Quad SABRE Automotive Board
+Required root node properties:
+ - compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
diff --git a/arch/arm/boot/dts/imx6q-sabreauto.dts b/arch/arm/boot/dts/imx6q-sabreauto.dts
new file mode 100644
index 0000000..7dd93e8
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q-sabreauto.dts
@@ -0,0 +1,82 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/dts-v1/;
+/include/ "imx6q.dtsi"
+
+/ {
+ model = "Freescale i.MX6 Quad SABRE Automotive Board";
+ compatible = "fsl,imx6q-sabreauto", "fsl,imx6q";
+
+ chosen {
+ bootargs = "console=ttymxc0,115200 root=/dev/mmcblk3p3 rootwait";
+ };
+
+ memory {
+ reg = <0x10000000 0x80000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ clkl {
+ compatible = "fsl,imx6q-clkl", "fixed-clock";
+ clock-frequency = <32768>;
+ };
+
+ clkh {
+ compatible = "fsl,imx6q-clkh", "fixed-clock";
+ clock-frequency = <0>;
+ };
+
+ osc {
+ compatible = "fsl,imx6q-osc", "fixed-clock";
+ clock-frequency = <24000000>;
+ };
+ };
+
+ soc {
+ aips-bus at 02100000 { /* AIPS2 */
+ enet at 02188000 {
+ phy-mode = "rgmii";
+ local-mac-address = [00 04 9F 01 1B 61];
+ status = "okay";
+ };
+
+ usdhc at 02198000 { /* uSDHC3 */
+ cd-gpios = <&gpio5 11 0>; /* GPIO6_11 */
+ wp-gpios = <&gpio5 14 0>; /* GPIO6_14 */
+ status = "okay";
+ };
+
+ usdhc at 0219c000 { /* uSDHC4 */
+ fsl,card-wired;
+ status = "okay";
+ };
+
+ uart3: uart at 021f0000 { /* UART4 */
+ status = "okay";
+ };
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ debug-led {
+ label = "Heartbeat";
+ gpios = <&gpio2 25 0>; /* GPIO3_25 */
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi
new file mode 100644
index 0000000..843e545
--- /dev/null
+++ b/arch/arm/boot/dts/imx6q.dtsi
@@ -0,0 +1,555 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+/include/ "skeleton.dtsi"
+
+/ {
+ aliases {
+ serial0 = &uart0;
+ serial1 = &uart1;
+ serial2 = &uart2;
+ serial3 = &uart3;
+ serial4 = &uart4;
+ };
+
+ cpus {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cpu at 0 {
+ compatible = "arm,cortex-a9";
+ reg = <0>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu at 1 {
+ compatible = "arm,cortex-a9";
+ reg = <1>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu at 2 {
+ compatible = "arm,cortex-a9";
+ reg = <2>;
+ next-level-cache = <&L2>;
+ };
+
+ cpu at 3 {
+ compatible = "arm,cortex-a9";
+ reg = <3>;
+ next-level-cache = <&L2>;
+ };
+ };
+
+ intc: interrupt-controller at 00a01000 {
+ compatible = "arm,cortex-a9-gic";
+ #interrupt-cells = <3>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ interrupt-controller;
+ reg = <0x00a01000 0x1000>,
+ <0x00a00100 0x100>;
+ };
+
+ soc {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ compatible = "simple-bus";
+ interrupt-parent = <&intc>;
+ ranges;
+
+ timer at 00a00600 {
+ compatible = "arm,smp-twd";
+ reg = <0x00a00600 0x100>;
+ interrupts = <1 13 0xf4>;
+ };
+
+ L2: l2-cache at 00a02000 {
+ compatible = "arm,pl310-cache";
+ reg = <0x00a02000 0x1000>;
+ interrupts = <0 92 0x04>;
+ cache-unified;
+ cache-level = <2>;
+ };
+
+ aips-bus at 02000000 { /* AIPS1 */
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x100000>;
+ ranges;
+
+ spba-bus at 02000000 {
+ compatible = "fsl,spba-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02000000 0x40000>;
+ ranges;
+
+ spdif at 02004000 {
+ reg = <0x02004000 0x4000>;
+ interrupts = <0 52 0x04>;
+ };
+
+ ecspi at 02008000 { /* eCSPI1 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02008000 0x4000>;
+ interrupts = <0 31 0x04>;
+ status = "disabled";
+ };
+
+ ecspi at 0200c000 { /* eCSPI2 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x0200c000 0x4000>;
+ interrupts = <0 32 0x04>;
+ status = "disabled";
+ };
+
+ ecspi at 02010000 { /* eCSPI3 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02010000 0x4000>;
+ interrupts = <0 33 0x04>;
+ status = "disabled";
+ };
+
+ ecspi at 02014000 { /* eCSPI4 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02014000 0x4000>;
+ interrupts = <0 34 0x04>;
+ status = "disabled";
+ };
+
+ ecspi at 02018000 { /* eCSPI5 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-ecspi", "fsl,imx51-ecspi";
+ reg = <0x02018000 0x4000>;
+ interrupts = <0 35 0x04>;
+ status = "disabled";
+ };
+
+ uart0: uart at 02020000 { /* UART1 */
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x02020000 0x4000>;
+ interrupts = <0 26 0x04>;
+ status = "disabled";
+ };
+
+ esai at 02024000 {
+ reg = <0x02024000 0x4000>;
+ interrupts = <0 51 0x04>;
+ };
+
+ ssi at 02028000 { /* SSI1 */
+ reg = <0x02028000 0x4000>;
+ interrupts = <0 46 0x04>;
+ };
+
+ ssi at 0202c000 { /* SSI2 */
+ reg = <0x0202c000 0x4000>;
+ interrupts = <0 47 0x04>;
+ };
+
+ ssi at 02030000 { /* SSI3 */
+ reg = <0x02030000 0x4000>;
+ interrupts = <0 48 0x04>;
+ };
+
+ asrc at 02034000 {
+ reg = <0x02034000 0x4000>;
+ interrupts = <0 50 0x04>;
+ };
+
+ spba at 0203c000 {
+ reg = <0x0203c000 0x4000>;
+ };
+ };
+
+ vpu at 02040000 {
+ reg = <0x02040000 0x3c000>;
+ interrupts = <0 3 0x04 0 12 0x04>;
+ };
+
+ aipstz at 0207c000 { /* AIPSTZ1 */
+ reg = <0x0207c000 0x4000>;
+ };
+
+ pwm at 02080000 { /* PWM1 */
+ reg = <0x02080000 0x4000>;
+ interrupts = <0 83 0x04>;
+ };
+
+ pwm at 02084000 { /* PWM2 */
+ reg = <0x02084000 0x4000>;
+ interrupts = <0 84 0x04>;
+ };
+
+ pwm at 02088000 { /* PWM3 */
+ reg = <0x02088000 0x4000>;
+ interrupts = <0 85 0x04>;
+ };
+
+ pwm at 0208c000 { /* PWM4 */
+ reg = <0x0208c000 0x4000>;
+ interrupts = <0 86 0x04>;
+ };
+
+ flexcan at 02090000 { /* CAN1 */
+ reg = <0x02090000 0x4000>;
+ interrupts = <0 110 0x04>;
+ };
+
+ flexcan at 02094000 { /* CAN2 */
+ reg = <0x02094000 0x4000>;
+ interrupts = <0 111 0x04>;
+ };
+
+ gpt at 02098000 {
+ compatible = "fsl,imx6q-gpt";
+ reg = <0x02098000 0x4000>;
+ interrupts = <0 55 0x04>;
+ };
+
+ gpio0: gpio at 0209c000 { /* GPIO1 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x0209c000 0x4000>;
+ interrupts = <0 66 0x04 0 67 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio1: gpio at 020a0000 { /* GPIO2 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x020a0000 0x4000>;
+ interrupts = <0 68 0x04 0 69 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio2: gpio at 020a4000 { /* GPIO3 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x020a4000 0x4000>;
+ interrupts = <0 70 0x04 0 71 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio3: gpio at 020a8000 { /* GPIO4 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x020a8000 0x4000>;
+ interrupts = <0 72 0x04 0 73 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio4: gpio at 020ac000 { /* GPIO5 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x020ac000 0x4000>;
+ interrupts = <0 74 0x04 0 75 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio5: gpio at 020b0000 { /* GPIO6 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x020b0000 0x4000>;
+ interrupts = <0 76 0x04 0 77 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ gpio6: gpio at 020b4000 { /* GPIO7 */
+ compatible = "fsl,imx6q-gpio", "fsl,imx31-gpio";
+ reg = <0x020b4000 0x4000>;
+ interrupts = <0 78 0x04 0 79 0x04>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ interrupt-controller;
+ #interrupt-cells = <1>;
+ };
+
+ kpp at 020b8000 {
+ reg = <0x020b8000 0x4000>;
+ interrupts = <0 82 0x04>;
+ };
+
+ wdog at 020bc000 { /* WDOG1 */
+ compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
+ reg = <0x020bc000 0x4000>;
+ interrupts = <0 80 0x04>;
+ status = "disabled";
+ };
+
+ wdog at 020c0000 { /* WDOG2 */
+ compatible = "fsl,imx6q-wdt", "fsl,imx21-wdt";
+ reg = <0x020c0000 0x4000>;
+ interrupts = <0 81 0x04>;
+ status = "disabled";
+ };
+
+ ccm at 020c4000 {
+ compatible = "fsl,imx6q-ccm";
+ reg = <0x020c4000 0x4000>;
+ interrupts = <0 87 0x04 0 88 0x04>;
+ };
+
+ anatop at 020c8000 {
+ compatible = "fsl,imx6q-anatop";
+ reg = <0x020c8000 0x1000>;
+ interrupts = <0 49 0x04 0 54 0x04 0 127 0x04>;
+ };
+
+ usbphy at 020c9000 { /* USBPHY1 */
+ reg = <0x020c9000 0x1000>;
+ interrupts = <0 44 0x04>;
+ };
+
+ usbphy at 020ca000 { /* USBPHY2 */
+ reg = <0x020ca000 0x1000>;
+ interrupts = <0 45 0x04>;
+ };
+
+ snvs at 020cc000 {
+ reg = <0x020cc000 0x4000>;
+ interrupts = <0 19 0x04 0 20 0x04>;
+ };
+
+ epit at 020d0000 { /* EPIT1 */
+ reg = <0x020d0000 0x4000>;
+ interrupts = <0 56 0x04>;
+ };
+
+ epit at 020d4000 { /* EPIT2 */
+ reg = <0x020d4000 0x4000>;
+ interrupts = <0 57 0x04>;
+ };
+
+ src at 020d8000 {
+ compatible = "fsl,imx6q-src";
+ reg = <0x020d8000 0x4000>;
+ interrupts = <0 91 0x04 0 96 0x04>;
+ };
+
+ gpc at 020dc000 {
+ compatible = "fsl,imx6q-gpc";
+ reg = <0x020dc000 0x4000>;
+ interrupts = <0 89 0x04 0 90 0x04>;
+ };
+
+ iomuxc at 020e0000 {
+ reg = <0x020e0000 0x4000>;
+ };
+
+ dcic at 020e4000 { /* DCIC1 */
+ reg = <0x020e4000 0x4000>;
+ interrupts = <0 124 0x04>;
+ };
+
+ dcic at 020e8000 { /* DCIC2 */
+ reg = <0x020e8000 0x4000>;
+ interrupts = <0 125 0x04>;
+ };
+
+ sdma at 020ec000 {
+ compatible = "fsl,imx6q-sdma", "fsl,imx35-sdma";
+ reg = <0x020ec000 0x4000>;
+ interrupts = <0 2 0x04>;
+ };
+ };
+
+ aips-bus at 02100000 { /* AIPS2 */
+ compatible = "fsl,aips-bus", "simple-bus";
+ #address-cells = <1>;
+ #size-cells = <1>;
+ reg = <0x02100000 0x100000>;
+ ranges;
+
+ caam at 02100000 {
+ reg = <0x02100000 0x40000>;
+ interrupts = <0 105 0x04 0 106 0x04>;
+ };
+
+ aipstz at 0217c000 { /* AIPSTZ2 */
+ reg = <0x0217c000 0x4000>;
+ };
+
+ enet at 02188000 {
+ compatible = "fsl,imx6q-fec";
+ reg = <0x02188000 0x4000>;
+ interrupts = <0 118 0x04 0 119 0x04>;
+ status = "disabled";
+ };
+
+ mlb at 0218c000 {
+ reg = <0x0218c000 0x4000>;
+ interrupts = <0 53 0x04 0 117 0x04 0 126 0x04>;
+ };
+
+ usdhc at 02190000 { /* uSDHC1 */
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x02190000 0x4000>;
+ interrupts = <0 22 0x04>;
+ status = "disabled";
+ };
+
+ usdhc at 02194000 { /* uSDHC2 */
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x02194000 0x4000>;
+ interrupts = <0 23 0x04>;
+ status = "disabled";
+ };
+
+ usdhc at 02198000 { /* uSDHC3 */
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x02198000 0x4000>;
+ interrupts = <0 24 0x04>;
+ status = "disabled";
+ };
+
+ usdhc at 0219c000 { /* uSDHC4 */
+ compatible = "fsl,imx6q-usdhc";
+ reg = <0x0219c000 0x4000>;
+ interrupts = <0 25 0x04>;
+ status = "disabled";
+ };
+
+ i2c at 021a0000 { /* I2C1 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx1-i2c";
+ reg = <0x021a0000 0x4000>;
+ interrupts = <0 36 0x04>;
+ status = "disabled";
+ };
+
+ i2c at 021a4000 { /* I2C2 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx1-i2c";
+ reg = <0x021a4000 0x4000>;
+ interrupts = <0 37 0x04>;
+ status = "disabled";
+ };
+
+ i2c at 021a8000 { /* I2C3 */
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "fsl,imx6q-i2c", "fsl,imx1-i2c";
+ reg = <0x021a8000 0x4000>;
+ interrupts = <0 38 0x04>;
+ status = "disabled";
+ };
+
+ romcp at 021ac000 {
+ reg = <0x021ac000 0x4000>;
+ };
+
+ mmdc at 021b0000 { /* MMDC0 */
+ compatible = "fsl,imx6q-mmdc";
+ reg = <0x021b0000 0x4000>;
+ };
+
+ mmdc at 021b4000 { /* MMDC1 */
+ reg = <0x021b4000 0x4000>;
+ };
+
+ weim at 021b8000 {
+ reg = <0x021b8000 0x4000>;
+ interrupts = <0 14 0x04>;
+ };
+
+ ocotp at 021bc000 {
+ reg = <0x021bc000 0x4000>;
+ };
+
+ ocotp at 021c0000 {
+ reg = <0x021c0000 0x4000>;
+ interrupts = <0 21 0x04>;
+ };
+
+ tzasc at 021d0000 { /* TZASC1 */
+ reg = <0x021d0000 0x4000>;
+ interrupts = <0 108 0x04>;
+ };
+
+ tzasc at 021d4000 { /* TZASC2 */
+ reg = <0x021d4000 0x4000>;
+ interrupts = <0 109 0x04>;
+ };
+
+ audmux at 021d8000 {
+ reg = <0x021d8000 0x4000>;
+ };
+
+ mipi at 021dc000 { /* MIPI-CSI */
+ reg = <0x021dc000 0x4000>;
+ };
+
+ mipi at 021e0000 { /* MIPI-DSI */
+ reg = <0x021e0000 0x4000>;
+ };
+
+ vdoa at 021e4000 {
+ reg = <0x021e4000 0x4000>;
+ interrupts = <0 18 0x04>;
+ };
+
+ uart1: uart at 021e8000 { /* UART2 */
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021e8000 0x4000>;
+ interrupts = <0 27 0x04>;
+ status = "disabled";
+ };
+
+ uart2: uart at 021ec000 { /* UART3 */
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021ec000 0x4000>;
+ interrupts = <0 28 0x04>;
+ status = "disabled";
+ };
+
+ uart3: uart at 021f0000 { /* UART4 */
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021f0000 0x4000>;
+ interrupts = <0 29 0x04>;
+ status = "disabled";
+ };
+
+ uart4: uart at 021f4000 { /* UART5 */
+ compatible = "fsl,imx6q-uart", "fsl,imx21-uart";
+ reg = <0x021f4000 0x4000>;
+ interrupts = <0 30 0x04>;
+ status = "disabled";
+ };
+ };
+ };
+};
--
1.7.4.1
^ permalink raw reply related
* [PATCH v4 2/7] arm/imx6q: add core definitions and low-level debug uart
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
It adds the core definitions and low-level debug uart support
for imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/Kconfig | 2 +-
arch/arm/Kconfig.debug | 7 +++++
arch/arm/Makefile | 1 +
arch/arm/mach-imx/Kconfig | 14 +++++++++++
arch/arm/mach-imx/Makefile | 2 +
arch/arm/mach-imx/Makefile.boot | 4 +++
arch/arm/mach-imx/lluart.c | 32 +++++++++++++++++++++++++
arch/arm/plat-mxc/Kconfig | 7 +++++
arch/arm/plat-mxc/include/mach/debug-macro.S | 2 +
arch/arm/plat-mxc/include/mach/hardware.h | 6 ++++
arch/arm/plat-mxc/include/mach/irqs.h | 10 ++++++-
arch/arm/plat-mxc/include/mach/memory.h | 1 +
arch/arm/plat-mxc/include/mach/mx6q.h | 33 ++++++++++++++++++++++++++
13 files changed, 118 insertions(+), 3 deletions(-)
create mode 100644 arch/arm/mach-imx/lluart.c
create mode 100644 arch/arm/plat-mxc/include/mach/mx6q.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 5cafa03..58d9343 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1363,7 +1363,7 @@ config SMP
depends on REALVIEW_EB_ARM11MP || REALVIEW_EB_A9MP || \
MACH_REALVIEW_PB11MP || MACH_REALVIEW_PBX || ARCH_OMAP4 || \
ARCH_EXYNOS4 || ARCH_TEGRA || ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || \
- ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE
+ ARCH_MSM_SCORPIONMP || ARCH_SHMOBILE || SOC_IMX6Q
select USE_GENERIC_SMP_HELPERS
select HAVE_ARM_SCU if !ARCH_MSM_SCORPIONMP
help
diff --git a/arch/arm/Kconfig.debug b/arch/arm/Kconfig.debug
index add32ff..ba206e0 100644
--- a/arch/arm/Kconfig.debug
+++ b/arch/arm/Kconfig.debug
@@ -155,6 +155,13 @@ choice
Say Y here if you want kernel low-level debugging support
on i.MX50 or i.MX53.
+ config DEBUG_IMX6Q_UART
+ bool "i.MX6Q Debug UART"
+ depends on SOC_IMX6Q
+ help
+ Say Y here if you want kernel low-level debugging support
+ on i.MX6Q.
+
config DEBUG_S3C_UART0
depends on PLAT_SAMSUNG
bool "Use S3C UART 0 for low-level debug"
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index 30b9201..fc36c1b 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -160,6 +160,7 @@ machine-$(CONFIG_ARCH_MV78XX0) := mv78xx0
machine-$(CONFIG_ARCH_IMX_V4_V5) := imx
machine-$(CONFIG_ARCH_MX3) := imx
machine-$(CONFIG_ARCH_MX5) := mx5
+machine-$(CONFIG_ARCH_MX6) := imx
machine-$(CONFIG_ARCH_MXS) := mxs
machine-$(CONFIG_ARCH_NETX) := netx
machine-$(CONFIG_ARCH_NOMADIK) := nomadik
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 46cf2c5..4586edf 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -592,3 +592,17 @@ config MACH_VPR200
configurations for the board and its peripherals.
endif
+
+if ARCH_MX6
+comment "i.MX6 family:"
+
+config SOC_IMX6Q
+ bool "i.MX6 Quad support"
+ select ARM_GIC
+ select CPU_V7
+ select USE_OF
+
+ help
+ This enables support for Freescale i.MX6 Quad processor.
+
+endif
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index d22096a..d291bc5 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -61,3 +61,5 @@ obj-$(CONFIG_MACH_MX35_3DS) += mach-mx35_3ds.o
obj-$(CONFIG_MACH_EUKREA_CPUIMX35) += mach-cpuimx35.o
obj-$(CONFIG_MACH_EUKREA_MBIMXSD35_BASEBOARD) += eukrea_mbimxsd35-baseboard.o
obj-$(CONFIG_MACH_VPR200) += mach-vpr200.o
+
+obj-$(CONFIG_DEBUG_LL) += lluart.o
diff --git a/arch/arm/mach-imx/Makefile.boot b/arch/arm/mach-imx/Makefile.boot
index dbe6120..22d8588 100644
--- a/arch/arm/mach-imx/Makefile.boot
+++ b/arch/arm/mach-imx/Makefile.boot
@@ -17,3 +17,7 @@ initrd_phys-$(CONFIG_MACH_MX27) := 0xA0800000
zreladdr-$(CONFIG_ARCH_MX3) += 0x80008000
params_phys-$(CONFIG_ARCH_MX3) := 0x80000100
initrd_phys-$(CONFIG_ARCH_MX3) := 0x80800000
+
+zreladdr-$(CONFIG_SOC_IMX6Q) += 0x10008000
+params_phys-$(CONFIG_SOC_IMX6Q) := 0x10000100
+initrd_phys-$(CONFIG_SOC_IMX6Q) := 0x10800000
diff --git a/arch/arm/mach-imx/lluart.c b/arch/arm/mach-imx/lluart.c
new file mode 100644
index 0000000..d4ab6f2
--- /dev/null
+++ b/arch/arm/mach-imx/lluart.c
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <asm/page.h>
+#include <asm/sizes.h>
+#include <asm/mach/map.h>
+#include <mach/hardware.h>
+
+static struct map_desc imx_lluart_desc = {
+#ifdef CONFIG_DEBUG_IMX6Q_UART
+ .virtual = MX6Q_IO_P2V(MX6Q_UART4_BASE_ADDR),
+ .pfn = __phys_to_pfn(MX6Q_UART4_BASE_ADDR),
+ .length = MX6Q_UART4_SIZE,
+ .type = MT_DEVICE,
+#endif
+};
+
+void __init imx_lluart_map_io(void)
+{
+ if (imx_lluart_desc.virtual)
+ iotable_init(&imx_lluart_desc, 1);
+}
diff --git a/arch/arm/plat-mxc/Kconfig b/arch/arm/plat-mxc/Kconfig
index 502e45f..e2e3e5a 100644
--- a/arch/arm/plat-mxc/Kconfig
+++ b/arch/arm/plat-mxc/Kconfig
@@ -29,6 +29,13 @@ config ARCH_MX5
This enables support for machines using Freescale's i.MX50 and i.MX51
processors.
+config ARCH_MX6
+ bool "i.MX6"
+ select AUTO_ZRELADDR
+ select ARM_PATCH_PHYS_VIRT
+ help
+ This enables support for systems based on the Freescale i.MX6 family
+
endchoice
source "arch/arm/mach-imx/Kconfig"
diff --git a/arch/arm/plat-mxc/include/mach/debug-macro.S b/arch/arm/plat-mxc/include/mach/debug-macro.S
index 07cfdbe..f2ce2cb 100644
--- a/arch/arm/plat-mxc/include/mach/debug-macro.S
+++ b/arch/arm/plat-mxc/include/mach/debug-macro.S
@@ -24,6 +24,8 @@
#define UART_PADDR MX51_UART1_BASE_ADDR
#elif defined (CONFIG_DEBUG_IMX50_IMX53_UART)
#define UART_PADDR MX53_UART1_BASE_ADDR
+#elif defined (CONFIG_DEBUG_IMX6Q_UART)
+#define UART_PADDR MX6Q_UART4_BASE_ADDR
#endif
#define UART_VADDR IMX_IO_ADDRESS(UART_PADDR)
diff --git a/arch/arm/plat-mxc/include/mach/hardware.h b/arch/arm/plat-mxc/include/mach/hardware.h
index eba3118..a599f01 100644
--- a/arch/arm/plat-mxc/include/mach/hardware.h
+++ b/arch/arm/plat-mxc/include/mach/hardware.h
@@ -91,6 +91,11 @@
* SPBA0 0x50000000+0x100000 -> 0xf5400000+0x100000
* AIPS1 0x53f00000+0x100000 -> 0xf5700000+0x100000
* AIPS2 0x63f00000+0x100000 -> 0xf5300000+0x100000
+ * mx6q:
+ * SCU 0x00a00000+0x001000 -> 0xf4000000+0x001000
+ * CCM 0x020c4000+0x004000 -> 0xf42c4000+0x004000
+ * ANATOP 0x020c8000+0x001000 -> 0xf42c8000+0x001000
+ * UART4 0x021f0000+0x004000 -> 0xf42f0000+0x004000
*/
#define IMX_IO_P2V(x) ( \
0xf4000000 + \
@@ -102,6 +107,7 @@
#include <mach/mxc.h>
+#include <mach/mx6q.h>
#include <mach/mx50.h>
#include <mach/mx51.h>
#include <mach/mx53.h>
diff --git a/arch/arm/plat-mxc/include/mach/irqs.h b/arch/arm/plat-mxc/include/mach/irqs.h
index 00e812b..fd9efb0 100644
--- a/arch/arm/plat-mxc/include/mach/irqs.h
+++ b/arch/arm/plat-mxc/include/mach/irqs.h
@@ -14,9 +14,15 @@
#include <asm-generic/gpio.h>
/*
- * SoCs with TZIC interrupt controller have 128 IRQs, those with AVIC have 64
+ * SoCs with GIC interrupt controller have 160 IRQs, those with TZIC
+ * have 128 IRQs, and those with AVIC have 64.
+ *
+ * To support single image, the biggest number should be defined on
+ * top of the list.
*/
-#ifdef CONFIG_MXC_TZIC
+#if defined CONFIG_ARM_GIC
+#define MXC_INTERNAL_IRQS 160
+#elif defined CONFIG_MXC_TZIC
#define MXC_INTERNAL_IRQS 128
#else
#define MXC_INTERNAL_IRQS 64
diff --git a/arch/arm/plat-mxc/include/mach/memory.h b/arch/arm/plat-mxc/include/mach/memory.h
index ae3541d..80e5bf2 100644
--- a/arch/arm/plat-mxc/include/mach/memory.h
+++ b/arch/arm/plat-mxc/include/mach/memory.h
@@ -19,6 +19,7 @@
#define MX50_PHYS_OFFSET UL(0x70000000)
#define MX51_PHYS_OFFSET UL(0x90000000)
#define MX53_PHYS_OFFSET UL(0x70000000)
+#define MX6Q_PHYS_OFFSET UL(0x10000000)
#if !defined(CONFIG_RUNTIME_PHYS_OFFSET)
# if defined CONFIG_ARCH_MX3
diff --git a/arch/arm/plat-mxc/include/mach/mx6q.h b/arch/arm/plat-mxc/include/mach/mx6q.h
new file mode 100644
index 0000000..254a561
--- /dev/null
+++ b/arch/arm/plat-mxc/include/mach/mx6q.h
@@ -0,0 +1,33 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc. All Rights Reserved.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#ifndef __MACH_MX6Q_H__
+#define __MACH_MX6Q_H__
+
+#define MX6Q_IO_P2V(x) IMX_IO_P2V(x)
+#define MX6Q_IO_ADDRESS(x) IOMEM(MX6Q_IO_P2V(x))
+
+/*
+ * The following are the blocks that need to be statically mapped.
+ * For other blocks, the base address really should be retrieved from
+ * device tree.
+ */
+#define MX6Q_SCU_BASE_ADDR 0x00a00000
+#define MX6Q_SCU_SIZE 0x1000
+#define MX6Q_CCM_BASE_ADDR 0x020c4000
+#define MX6Q_CCM_SIZE 0x4000
+#define MX6Q_ANATOP_BASE_ADDR 0x020c8000
+#define MX6Q_ANATOP_SIZE 0x1000
+#define MX6Q_UART4_BASE_ADDR 0x021f0000
+#define MX6Q_UART4_SIZE 0x4000
+
+#endif /* __MACH_MX6Q_H__ */
--
1.7.4.1
^ permalink raw reply related
* [PATCH v4 3/7] arm/imx: add gic_handle_irq function
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
This is a plain translation of assembly gic irq handler to C function
for CONFIG_MULTI_IRQ_HANDLER support on imx family.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/plat-mxc/Makefile | 2 +-
arch/arm/plat-mxc/gic.c | 47 ++++++++++++++++++++++++++
arch/arm/plat-mxc/include/mach/common.h | 2 +
arch/arm/plat-mxc/include/mach/entry-macro.S | 6 +++
4 files changed, 56 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/plat-mxc/gic.c
diff --git a/arch/arm/plat-mxc/Makefile b/arch/arm/plat-mxc/Makefile
index d53c35f..b9f0f5f 100644
--- a/arch/arm/plat-mxc/Makefile
+++ b/arch/arm/plat-mxc/Makefile
@@ -5,7 +5,7 @@
# Common support
obj-y := clock.o time.o devices.o cpu.o system.o irq-common.o
-# MX51 uses the TZIC interrupt controller, older platforms use AVIC
+obj-$(CONFIG_ARM_GIC) += gic.o
obj-$(CONFIG_MXC_TZIC) += tzic.o
obj-$(CONFIG_MXC_AVIC) += avic.o
diff --git a/arch/arm/plat-mxc/gic.c b/arch/arm/plat-mxc/gic.c
new file mode 100644
index 0000000..487d12c
--- /dev/null
+++ b/arch/arm/plat-mxc/gic.c
@@ -0,0 +1,47 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/io.h>
+#include <asm/localtimer.h>
+#include <asm/hardware/gic.h>
+#ifdef CONFIG_SMP
+#include <asm/smp.h>
+#endif
+
+asmlinkage void __exception_irq_entry gic_handle_irq(struct pt_regs *regs)
+{
+ u32 irqstat, irqnr;
+
+ do {
+ irqstat = readl_relaxed(gic_cpu_base_addr + GIC_CPU_INTACK);
+ irqnr = irqstat & 0x3ff;
+ if (irqnr == 1023)
+ break;
+
+ if (irqnr > 29 && irqnr < 1021)
+ handle_IRQ(irqnr, regs);
+#ifdef CONFIG_SMP
+ else if (irqnr < 16) {
+ writel_relaxed(irqstat, gic_cpu_base_addr +
+ GIC_CPU_EOI);
+ do_IPI(irqnr, regs);
+ }
+#endif
+#ifdef CONFIG_LOCAL_TIMERS
+ else if (irqnr == 29) {
+ writel_relaxed(irqstat, gic_cpu_base_addr +
+ GIC_CPU_EOI);
+ do_local_timer(regs);
+ }
+#endif
+ } while (1);
+}
diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
index 9f15a79..988fa9a 100644
--- a/arch/arm/plat-mxc/include/mach/common.h
+++ b/arch/arm/plat-mxc/include/mach/common.h
@@ -75,6 +75,7 @@ extern void imx_print_silicon_rev(const char *cpu, int srev);
void avic_handle_irq(struct pt_regs *);
void tzic_handle_irq(struct pt_regs *);
+void gic_handle_irq(struct pt_regs *);
#define imx1_handle_irq avic_handle_irq
#define imx21_handle_irq avic_handle_irq
@@ -85,5 +86,6 @@ void tzic_handle_irq(struct pt_regs *);
#define imx50_handle_irq tzic_handle_irq
#define imx51_handle_irq tzic_handle_irq
#define imx53_handle_irq tzic_handle_irq
+#define imx6q_handle_irq gic_handle_irq
#endif
diff --git a/arch/arm/plat-mxc/include/mach/entry-macro.S b/arch/arm/plat-mxc/include/mach/entry-macro.S
index 842fbcb..9fe0dfc 100644
--- a/arch/arm/plat-mxc/include/mach/entry-macro.S
+++ b/arch/arm/plat-mxc/include/mach/entry-macro.S
@@ -22,3 +22,9 @@
.macro get_irqnr_and_base, irqnr, irqstat, base, tmp
.endm
+
+ .macro test_for_ipi, irqnr, irqstat, base, tmp
+ .endm
+
+ .macro test_for_ltirq, irqnr, irqstat, base, tmp
+ .endm
--
1.7.4.1
^ permalink raw reply related
* [PATCH v4 4/7] arm/imx6q: add core drivers clock, gpc, mmdc and src
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
It adds a number of core drivers support for imx6q, including clock,
General Power Controller (gpc), Multi Mode DDR Controller(mmdc) and
System Reset Controller (src).
Signed-off-by: Ranjani Vaidyanathan <ra5478@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/Kconfig | 13 +
arch/arm/mach-imx/Makefile | 4 +
arch/arm/mach-imx/clock-imx6q.c | 2012 +++++++++++++++++++++++++++++++++++++++
arch/arm/mach-imx/gpc.c | 113 +++
arch/arm/mach-imx/mmdc.c | 72 ++
arch/arm/mach-imx/src.c | 49 +
6 files changed, 2263 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-imx/clock-imx6q.c
create mode 100644 arch/arm/mach-imx/gpc.c
create mode 100644 arch/arm/mach-imx/mmdc.c
create mode 100644 arch/arm/mach-imx/src.c
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 4586edf..7555410 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -1,5 +1,15 @@
config IMX_HAVE_DMA_V1
bool
+
+config HAVE_IMX_GPC
+ bool
+
+config HAVE_IMX_MMDC
+ bool
+
+config HAVE_IMX_SRC
+ bool
+
#
# ARCH_MX31 and ARCH_MX35 are left for compatibility
# Some usages assume that having one of them implies not having (e.g.) ARCH_MX2.
@@ -600,6 +610,9 @@ config SOC_IMX6Q
bool "i.MX6 Quad support"
select ARM_GIC
select CPU_V7
+ select HAVE_IMX_GPC
+ select HAVE_IMX_MMDC
+ select HAVE_IMX_SRC
select USE_OF
help
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index d291bc5..c71e3c5 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -63,3 +63,7 @@ obj-$(CONFIG_MACH_EUKREA_MBIMXSD35_BASEBOARD) += eukrea_mbimxsd35-baseboard.o
obj-$(CONFIG_MACH_VPR200) += mach-vpr200.o
obj-$(CONFIG_DEBUG_LL) += lluart.o
+obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
+obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
+obj-$(CONFIG_HAVE_IMX_SRC) += src.o
+obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o
diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c
new file mode 100644
index 0000000..66f4add
--- /dev/null
+++ b/arch/arm/mach-imx/clock-imx6q.c
@@ -0,0 +1,2012 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/types.h>
+#include <linux/clk.h>
+#include <linux/clkdev.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <asm/div64.h>
+#include <asm/mach/map.h>
+#include <mach/clock.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+
+#define PLL_BASE IMX_IO_ADDRESS(MX6Q_ANATOP_BASE_ADDR)
+#define PLL1_SYS (PLL_BASE + 0x000)
+#define PLL2_BUS (PLL_BASE + 0x030)
+#define PLL3_USB_OTG (PLL_BASE + 0x010)
+#define PLL4_AUDIO (PLL_BASE + 0x070)
+#define PLL5_VIDEO (PLL_BASE + 0x0a0)
+#define PLL6_MLB (PLL_BASE + 0x0d0)
+#define PLL7_USB_HOST (PLL_BASE + 0x020)
+#define PLL8_ENET (PLL_BASE + 0x0e0)
+#define PFD_480 (PLL_BASE + 0x0f0)
+#define PFD_528 (PLL_BASE + 0x100)
+#define PLL_NUM_OFFSET 0x010
+#define PLL_DENOM_OFFSET 0x020
+
+#define PFD0 7
+#define PFD1 15
+#define PFD2 23
+#define PFD3 31
+#define PFD_FRAC_MASK 0x3f
+
+#define BM_PLL_BYPASS (0x1 << 16)
+#define BM_PLL_ENABLE (0x1 << 13)
+#define BM_PLL_POWER_DOWN (0x1 << 12)
+#define BM_PLL_LOCK (0x1 << 31)
+#define BP_PLL_SYS_DIV_SELECT 0
+#define BM_PLL_SYS_DIV_SELECT (0x7f << 0)
+#define BP_PLL_BUS_DIV_SELECT 0
+#define BM_PLL_BUS_DIV_SELECT (0x1 << 0)
+#define BP_PLL_USB_DIV_SELECT 0
+#define BM_PLL_USB_DIV_SELECT (0x3 << 0)
+#define BP_PLL_AV_DIV_SELECT 0
+#define BM_PLL_AV_DIV_SELECT (0x7f << 0)
+#define BP_PLL_ENET_DIV_SELECT 0
+#define BM_PLL_ENET_DIV_SELECT (0x3 << 0)
+#define BM_PLL_ENET_EN_PCIE (0x1 << 19)
+#define BM_PLL_ENET_EN_SATA (0x1 << 20)
+
+#define CCM_BASE IMX_IO_ADDRESS(MX6Q_CCM_BASE_ADDR)
+#define CCR (CCM_BASE + 0x00)
+#define CCDR (CCM_BASE + 0x04)
+#define CSR (CCM_BASE + 0x08)
+#define CCSR (CCM_BASE + 0x0c)
+#define CACRR (CCM_BASE + 0x10)
+#define CBCDR (CCM_BASE + 0x14)
+#define CBCMR (CCM_BASE + 0x18)
+#define CSCMR1 (CCM_BASE + 0x1c)
+#define CSCMR2 (CCM_BASE + 0x20)
+#define CSCDR1 (CCM_BASE + 0x24)
+#define CS1CDR (CCM_BASE + 0x28)
+#define CS2CDR (CCM_BASE + 0x2c)
+#define CDCDR (CCM_BASE + 0x30)
+#define CHSCCDR (CCM_BASE + 0x34)
+#define CSCDR2 (CCM_BASE + 0x38)
+#define CSCDR3 (CCM_BASE + 0x3c)
+#define CSCDR4 (CCM_BASE + 0x40)
+#define CWDR (CCM_BASE + 0x44)
+#define CDHIPR (CCM_BASE + 0x48)
+#define CDCR (CCM_BASE + 0x4c)
+#define CTOR (CCM_BASE + 0x50)
+#define CLPCR (CCM_BASE + 0x54)
+#define CISR (CCM_BASE + 0x58)
+#define CIMR (CCM_BASE + 0x5c)
+#define CCOSR (CCM_BASE + 0x60)
+#define CGPR (CCM_BASE + 0x64)
+#define CCGR0 (CCM_BASE + 0x68)
+#define CCGR1 (CCM_BASE + 0x6c)
+#define CCGR2 (CCM_BASE + 0x70)
+#define CCGR3 (CCM_BASE + 0x74)
+#define CCGR4 (CCM_BASE + 0x78)
+#define CCGR5 (CCM_BASE + 0x7c)
+#define CCGR6 (CCM_BASE + 0x80)
+#define CCGR7 (CCM_BASE + 0x84)
+#define CMEOR (CCM_BASE + 0x88)
+
+#define CG0 0
+#define CG1 2
+#define CG2 4
+#define CG3 6
+#define CG4 8
+#define CG5 10
+#define CG6 12
+#define CG7 14
+#define CG8 16
+#define CG9 18
+#define CG10 20
+#define CG11 22
+#define CG12 24
+#define CG13 26
+#define CG14 28
+#define CG15 30
+
+#define BM_CCSR_PLL1_SW_SEL (0x1 << 2)
+#define BM_CCSR_STEP_SEL (0x1 << 8)
+
+#define BP_CACRR_ARM_PODF 0
+#define BM_CACRR_ARM_PODF (0x7 << 0)
+
+#define BP_CBCDR_PERIPH2_CLK2_PODF 0
+#define BM_CBCDR_PERIPH2_CLK2_PODF (0x7 << 0)
+#define BP_CBCDR_MMDC_CH1_AXI_PODF 3
+#define BM_CBCDR_MMDC_CH1_AXI_PODF (0x7 << 3)
+#define BP_CBCDR_AXI_SEL 6
+#define BM_CBCDR_AXI_SEL (0x3 << 6)
+#define BP_CBCDR_IPG_PODF 8
+#define BM_CBCDR_IPG_PODF (0x3 << 8)
+#define BP_CBCDR_AHB_PODF 10
+#define BM_CBCDR_AHB_PODF (0x7 << 10)
+#define BP_CBCDR_AXI_PODF 16
+#define BM_CBCDR_AXI_PODF (0x7 << 16)
+#define BP_CBCDR_MMDC_CH0_AXI_PODF 19
+#define BM_CBCDR_MMDC_CH0_AXI_PODF (0x7 << 19)
+#define BP_CBCDR_PERIPH_CLK_SEL 25
+#define BM_CBCDR_PERIPH_CLK_SEL (0x1 << 25)
+#define BP_CBCDR_PERIPH2_CLK_SEL 26
+#define BM_CBCDR_PERIPH2_CLK_SEL (0x1 << 26)
+#define BP_CBCDR_PERIPH_CLK2_PODF 27
+#define BM_CBCDR_PERIPH_CLK2_PODF (0x7 << 27)
+
+#define BP_CBCMR_GPU2D_AXI_SEL 0
+#define BM_CBCMR_GPU2D_AXI_SEL (0x1 << 0)
+#define BP_CBCMR_GPU3D_AXI_SEL 1
+#define BM_CBCMR_GPU3D_AXI_SEL (0x1 << 1)
+#define BP_CBCMR_GPU3D_CORE_SEL 4
+#define BM_CBCMR_GPU3D_CORE_SEL (0x3 << 4)
+#define BP_CBCMR_GPU3D_SHADER_SEL 8
+#define BM_CBCMR_GPU3D_SHADER_SEL (0x3 << 8)
+#define BP_CBCMR_PCIE_AXI_SEL 10
+#define BM_CBCMR_PCIE_AXI_SEL (0x1 << 10)
+#define BP_CBCMR_VDO_AXI_SEL 11
+#define BM_CBCMR_VDO_AXI_SEL (0x1 << 11)
+#define BP_CBCMR_PERIPH_CLK2_SEL 12
+#define BM_CBCMR_PERIPH_CLK2_SEL (0x3 << 12)
+#define BP_CBCMR_VPU_AXI_SEL 14
+#define BM_CBCMR_VPU_AXI_SEL (0x3 << 14)
+#define BP_CBCMR_GPU2D_CORE_SEL 16
+#define BM_CBCMR_GPU2D_CORE_SEL (0x3 << 16)
+#define BP_CBCMR_PRE_PERIPH_CLK_SEL 18
+#define BM_CBCMR_PRE_PERIPH_CLK_SEL (0x3 << 18)
+#define BP_CBCMR_PERIPH2_CLK2_SEL 20
+#define BM_CBCMR_PERIPH2_CLK2_SEL (0x1 << 20)
+#define BP_CBCMR_PRE_PERIPH2_CLK_SEL 21
+#define BM_CBCMR_PRE_PERIPH2_CLK_SEL (0x3 << 21)
+#define BP_CBCMR_GPU2D_CORE_PODF 23
+#define BM_CBCMR_GPU2D_CORE_PODF (0x7 << 23)
+#define BP_CBCMR_GPU3D_CORE_PODF 26
+#define BM_CBCMR_GPU3D_CORE_PODF (0x7 << 26)
+#define BP_CBCMR_GPU3D_SHADER_PODF 29
+#define BM_CBCMR_GPU3D_SHADER_PODF (0x7 << 29)
+
+#define BP_CSCMR1_PERCLK_PODF 0
+#define BM_CSCMR1_PERCLK_PODF (0x3f << 0)
+#define BP_CSCMR1_SSI1_SEL 10
+#define BM_CSCMR1_SSI1_SEL (0x3 << 10)
+#define BP_CSCMR1_SSI2_SEL 12
+#define BM_CSCMR1_SSI2_SEL (0x3 << 12)
+#define BP_CSCMR1_SSI3_SEL 14
+#define BM_CSCMR1_SSI3_SEL (0x3 << 14)
+#define BP_CSCMR1_USDHC1_SEL 16
+#define BM_CSCMR1_USDHC1_SEL (0x1 << 16)
+#define BP_CSCMR1_USDHC2_SEL 17
+#define BM_CSCMR1_USDHC2_SEL (0x1 << 17)
+#define BP_CSCMR1_USDHC3_SEL 18
+#define BM_CSCMR1_USDHC3_SEL (0x1 << 18)
+#define BP_CSCMR1_USDHC4_SEL 19
+#define BM_CSCMR1_USDHC4_SEL (0x1 << 19)
+#define BP_CSCMR1_EMI_PODF 20
+#define BM_CSCMR1_EMI_PODF (0x7 << 20)
+#define BP_CSCMR1_EMI_SLOW_PODF 23
+#define BM_CSCMR1_EMI_SLOW_PODF (0x7 << 23)
+#define BP_CSCMR1_EMI_SEL 27
+#define BM_CSCMR1_EMI_SEL (0x3 << 27)
+#define BP_CSCMR1_EMI_SLOW_SEL 29
+#define BM_CSCMR1_EMI_SLOW_SEL (0x3 << 29)
+
+#define BP_CSCMR2_CAN_PODF 2
+#define BM_CSCMR2_CAN_PODF (0x3f << 2)
+#define BM_CSCMR2_LDB_DI0_IPU_DIV (0x1 << 10)
+#define BM_CSCMR2_LDB_DI1_IPU_DIV (0x1 << 11)
+#define BP_CSCMR2_ESAI_SEL 19
+#define BM_CSCMR2_ESAI_SEL (0x3 << 19)
+
+#define BP_CSCDR1_UART_PODF 0
+#define BM_CSCDR1_UART_PODF (0x3f << 0)
+#define BP_CSCDR1_USDHC1_PODF 11
+#define BM_CSCDR1_USDHC1_PODF (0x7 << 11)
+#define BP_CSCDR1_USDHC2_PODF 16
+#define BM_CSCDR1_USDHC2_PODF (0x7 << 16)
+#define BP_CSCDR1_USDHC3_PODF 19
+#define BM_CSCDR1_USDHC3_PODF (0x7 << 19)
+#define BP_CSCDR1_USDHC4_PODF 22
+#define BM_CSCDR1_USDHC4_PODF (0x7 << 22)
+#define BP_CSCDR1_VPU_AXI_PODF 25
+#define BM_CSCDR1_VPU_AXI_PODF (0x7 << 25)
+
+#define BP_CS1CDR_SSI1_PODF 0
+#define BM_CS1CDR_SSI1_PODF (0x3f << 0)
+#define BP_CS1CDR_SSI1_PRED 6
+#define BM_CS1CDR_SSI1_PRED (0x7 << 6)
+#define BP_CS1CDR_ESAI_PRED 9
+#define BM_CS1CDR_ESAI_PRED (0x7 << 9)
+#define BP_CS1CDR_SSI3_PODF 16
+#define BM_CS1CDR_SSI3_PODF (0x3f << 16)
+#define BP_CS1CDR_SSI3_PRED 22
+#define BM_CS1CDR_SSI3_PRED (0x7 << 22)
+#define BP_CS1CDR_ESAI_PODF 25
+#define BM_CS1CDR_ESAI_PODF (0x7 << 25)
+
+#define BP_CS2CDR_SSI2_PODF 0
+#define BM_CS2CDR_SSI2_PODF (0x3f << 0)
+#define BP_CS2CDR_SSI2_PRED 6
+#define BM_CS2CDR_SSI2_PRED (0x7 << 6)
+#define BP_CS2CDR_LDB_DI0_SEL 9
+#define BM_CS2CDR_LDB_DI0_SEL (0x7 << 9)
+#define BP_CS2CDR_LDB_DI1_SEL 12
+#define BM_CS2CDR_LDB_DI1_SEL (0x7 << 12)
+#define BP_CS2CDR_ENFC_SEL 16
+#define BM_CS2CDR_ENFC_SEL (0x3 << 16)
+#define BP_CS2CDR_ENFC_PRED 18
+#define BM_CS2CDR_ENFC_PRED (0x7 << 18)
+#define BP_CS2CDR_ENFC_PODF 21
+#define BM_CS2CDR_ENFC_PODF (0x3f << 21)
+
+#define BP_CDCDR_ASRC_SERIAL_SEL 7
+#define BM_CDCDR_ASRC_SERIAL_SEL (0x3 << 7)
+#define BP_CDCDR_ASRC_SERIAL_PODF 9
+#define BM_CDCDR_ASRC_SERIAL_PODF (0x7 << 9)
+#define BP_CDCDR_ASRC_SERIAL_PRED 12
+#define BM_CDCDR_ASRC_SERIAL_PRED (0x7 << 12)
+#define BP_CDCDR_SPDIF_SEL 20
+#define BM_CDCDR_SPDIF_SEL (0x3 << 20)
+#define BP_CDCDR_SPDIF_PODF 22
+#define BM_CDCDR_SPDIF_PODF (0x7 << 22)
+#define BP_CDCDR_SPDIF_PRED 25
+#define BM_CDCDR_SPDIF_PRED (0x7 << 25)
+#define BP_CDCDR_HSI_TX_PODF 29
+#define BM_CDCDR_HSI_TX_PODF (0x7 << 29)
+#define BP_CDCDR_HSI_TX_SEL 28
+#define BM_CDCDR_HSI_TX_SEL (0x1 << 28)
+
+#define BP_CHSCCDR_IPU1_DI0_SEL 0
+#define BM_CHSCCDR_IPU1_DI0_SEL (0x7 << 0)
+#define BP_CHSCCDR_IPU1_DI0_PRE_PODF 3
+#define BM_CHSCCDR_IPU1_DI0_PRE_PODF (0x7 << 3)
+#define BP_CHSCCDR_IPU1_DI0_PRE_SEL 6
+#define BM_CHSCCDR_IPU1_DI0_PRE_SEL (0x7 << 6)
+#define BP_CHSCCDR_IPU1_DI1_SEL 9
+#define BM_CHSCCDR_IPU1_DI1_SEL (0x7 << 9)
+#define BP_CHSCCDR_IPU1_DI1_PRE_PODF 12
+#define BM_CHSCCDR_IPU1_DI1_PRE_PODF (0x7 << 12)
+#define BP_CHSCCDR_IPU1_DI1_PRE_SEL 15
+#define BM_CHSCCDR_IPU1_DI1_PRE_SEL (0x7 << 15)
+
+#define BP_CSCDR2_IPU2_DI0_SEL 0
+#define BM_CSCDR2_IPU2_DI0_SEL (0x7)
+#define BP_CSCDR2_IPU2_DI0_PRE_PODF 3
+#define BM_CSCDR2_IPU2_DI0_PRE_PODF (0x7 << 3)
+#define BP_CSCDR2_IPU2_DI0_PRE_SEL 6
+#define BM_CSCDR2_IPU2_DI0_PRE_SEL (0x7 << 6)
+#define BP_CSCDR2_IPU2_DI1_SEL 9
+#define BM_CSCDR2_IPU2_DI1_SEL (0x7 << 9)
+#define BP_CSCDR2_IPU2_DI1_PRE_PODF 12
+#define BM_CSCDR2_IPU2_DI1_PRE_PODF (0x7 << 12)
+#define BP_CSCDR2_IPU2_DI1_PRE_SEL 15
+#define BM_CSCDR2_IPU2_DI1_PRE_SEL (0x7 << 15)
+#define BP_CSCDR2_ECSPI_CLK_PODF 19
+#define BM_CSCDR2_ECSPI_CLK_PODF (0x3f << 19)
+
+#define BP_CSCDR3_IPU1_HSP_SEL 9
+#define BM_CSCDR3_IPU1_HSP_SEL (0x3 << 9)
+#define BP_CSCDR3_IPU1_HSP_PODF 11
+#define BM_CSCDR3_IPU1_HSP_PODF (0x7 << 11)
+#define BP_CSCDR3_IPU2_HSP_SEL 14
+#define BM_CSCDR3_IPU2_HSP_SEL (0x3 << 14)
+#define BP_CSCDR3_IPU2_HSP_PODF 16
+#define BM_CSCDR3_IPU2_HSP_PODF (0x7 << 16)
+
+#define BM_CDHIPR_AXI_PODF_BUSY (0x1 << 0)
+#define BM_CDHIPR_AHB_PODF_BUSY (0x1 << 1)
+#define BM_CDHIPR_MMDC_CH1_PODF_BUSY (0x1 << 2)
+#define BM_CDHIPR_PERIPH2_SEL_BUSY (0x1 << 3)
+#define BM_CDHIPR_MMDC_CH0_PODF_BUSY (0x1 << 4)
+#define BM_CDHIPR_PERIPH_SEL_BUSY (0x1 << 5)
+#define BM_CDHIPR_ARM_PODF_BUSY (0x1 << 16)
+
+#define BP_CLPCR_LPM 0
+#define BM_CLPCR_LPM (0x3 << 0)
+#define BM_CLPCR_BYPASS_PMIC_READY (0x1 << 2)
+#define BM_CLPCR_ARM_CLK_DIS_ON_LPM (0x1 << 5)
+#define BM_CLPCR_SBYOS (0x1 << 6)
+#define BM_CLPCR_DIS_REF_OSC (0x1 << 7)
+#define BM_CLPCR_VSTBY (0x1 << 8)
+#define BP_CLPCR_STBY_COUNT 9
+#define BM_CLPCR_STBY_COUNT (0x3 << 9)
+#define BM_CLPCR_COSC_PWRDOWN (0x1 << 11)
+#define BM_CLPCR_WB_PER_AT_LPM (0x1 << 16)
+#define BM_CLPCR_WB_CORE_AT_LPM (0x1 << 17)
+#define BM_CLPCR_BYP_MMDC_CH0_LPM_HS (0x1 << 19)
+#define BM_CLPCR_BYP_MMDC_CH1_LPM_HS (0x1 << 21)
+#define BM_CLPCR_MASK_CORE0_WFI (0x1 << 22)
+#define BM_CLPCR_MASK_CORE1_WFI (0x1 << 23)
+#define BM_CLPCR_MASK_CORE2_WFI (0x1 << 24)
+#define BM_CLPCR_MASK_CORE3_WFI (0x1 << 25)
+#define BM_CLPCR_MASK_SCU_IDLE (0x1 << 26)
+#define BM_CLPCR_MASK_L2CC_IDLE (0x1 << 27)
+
+#define FREQ_480M 480000000
+#define FREQ_528M 528000000
+#define FREQ_594M 594000000
+#define FREQ_650M 650000000
+#define FREQ_1300M 1300000000
+
+static struct clk pll1_sys;
+static struct clk pll2_bus;
+static struct clk pll3_usb_otg;
+static struct clk pll4_audio;
+static struct clk pll5_video;
+static struct clk pll6_mlb;
+static struct clk pll7_usb_host;
+static struct clk pll8_enet;
+static struct clk apbh_dma_clk;
+static struct clk arm_clk;
+static struct clk ipg_clk;
+static struct clk ahb_clk;
+static struct clk axi_clk;
+static struct clk mmdc_ch0_axi_clk;
+static struct clk mmdc_ch1_axi_clk;
+static struct clk periph_clk;
+static struct clk periph_pre_clk;
+static struct clk periph_clk2_clk;
+static struct clk periph2_clk;
+static struct clk periph2_pre_clk;
+static struct clk periph2_clk2_clk;
+static struct clk gpu2d_core_clk;
+static struct clk gpu3d_core_clk;
+static struct clk gpu3d_shader_clk;
+static struct clk ipg_perclk;
+static struct clk emi_clk;
+static struct clk emi_slow_clk;
+static struct clk can1_clk;
+static struct clk uart_clk;
+static struct clk usdhc1_clk;
+static struct clk usdhc2_clk;
+static struct clk usdhc3_clk;
+static struct clk usdhc4_clk;
+static struct clk vpu_clk;
+static struct clk hsi_tx_clk;
+static struct clk ipu1_di0_pre_clk;
+static struct clk ipu1_di1_pre_clk;
+static struct clk ipu2_di0_pre_clk;
+static struct clk ipu2_di1_pre_clk;
+static struct clk ipu1_clk;
+static struct clk ipu2_clk;
+static struct clk ssi1_clk;
+static struct clk ssi3_clk;
+static struct clk esai_clk;
+static struct clk ssi2_clk;
+static struct clk spdif_clk;
+static struct clk asrc_serial_clk;
+static struct clk gpu2d_axi_clk;
+static struct clk gpu3d_axi_clk;
+static struct clk pcie_clk;
+static struct clk vdo_axi_clk;
+static struct clk ldb_di0_clk;
+static struct clk ldb_di1_clk;
+static struct clk ipu1_di0_clk;
+static struct clk ipu1_di1_clk;
+static struct clk ipu2_di0_clk;
+static struct clk ipu2_di1_clk;
+static struct clk enfc_clk;
+static struct clk dummy_clk = {};
+
+static unsigned long external_high_reference;
+static unsigned long external_low_reference;
+static unsigned long oscillator_reference;
+
+static unsigned long get_oscillator_reference_clock_rate(struct clk *clk)
+{
+ return oscillator_reference;
+}
+
+static unsigned long get_high_reference_clock_rate(struct clk *clk)
+{
+ return external_high_reference;
+}
+
+static unsigned long get_low_reference_clock_rate(struct clk *clk)
+{
+ return external_low_reference;
+}
+
+static struct clk ckil_clk = {
+ .get_rate = get_low_reference_clock_rate,
+};
+
+static struct clk ckih_clk = {
+ .get_rate = get_high_reference_clock_rate,
+};
+
+static struct clk osc_clk = {
+ .get_rate = get_oscillator_reference_clock_rate,
+};
+
+static inline void __iomem *pll_get_reg_addr(struct clk *pll)
+{
+ if (pll == &pll1_sys)
+ return PLL1_SYS;
+ else if (pll == &pll2_bus)
+ return PLL2_BUS;
+ else if (pll == &pll3_usb_otg)
+ return PLL3_USB_OTG;
+ else if (pll == &pll4_audio)
+ return PLL4_AUDIO;
+ else if (pll == &pll5_video)
+ return PLL5_VIDEO;
+ else if (pll == &pll6_mlb)
+ return PLL6_MLB;
+ else if (pll == &pll7_usb_host)
+ return PLL7_USB_HOST;
+ else if (pll == &pll8_enet)
+ return PLL8_ENET;
+ else
+ BUG();
+
+ return NULL;
+}
+
+static int pll_enable(struct clk *clk)
+{
+ int timeout = 0x100000;
+ void __iomem *reg;
+ u32 val;
+
+ reg = pll_get_reg_addr(clk);
+ val = readl_relaxed(reg);
+ val &= ~BM_PLL_BYPASS;
+ val &= ~BM_PLL_POWER_DOWN;
+ /* 480MHz PLLs have the opposite definition for power bit */
+ if (clk == &pll3_usb_otg || clk == &pll7_usb_host)
+ val |= BM_PLL_POWER_DOWN;
+ writel_relaxed(val, reg);
+
+ /* Wait for PLL to lock */
+ while (!(readl_relaxed(reg) & BM_PLL_LOCK) && --timeout)
+ cpu_relax();
+
+ if (unlikely(!timeout))
+ return -EBUSY;
+
+ /* Enable the PLL output now */
+ val = readl_relaxed(reg);
+ val |= BM_PLL_ENABLE;
+ writel_relaxed(val, reg);
+
+ return 0;
+}
+
+static void pll_disable(struct clk *clk)
+{
+ void __iomem *reg;
+ u32 val;
+
+ reg = pll_get_reg_addr(clk);
+ val = readl_relaxed(reg);
+ val &= ~BM_PLL_ENABLE;
+ val |= BM_PLL_BYPASS;
+ val |= BM_PLL_POWER_DOWN;
+ if (clk == &pll3_usb_otg || clk == &pll7_usb_host)
+ val &= ~BM_PLL_POWER_DOWN;
+ writel_relaxed(val, reg);
+}
+
+static unsigned long pll1_sys_get_rate(struct clk *clk)
+{
+ u32 div = (readl_relaxed(PLL1_SYS) & BM_PLL_SYS_DIV_SELECT) >>
+ BP_PLL_SYS_DIV_SELECT;
+
+ return clk_get_rate(clk->parent) * div / 2;
+}
+
+static int pll1_sys_set_rate(struct clk *clk, unsigned long rate)
+{
+ u32 val, div;
+
+ if (rate < FREQ_650M || rate > FREQ_1300M)
+ return -EINVAL;
+
+ div = rate * 2 / clk_get_rate(clk->parent);
+ val = readl_relaxed(PLL1_SYS);
+ val &= ~BM_PLL_SYS_DIV_SELECT;
+ val |= div << BP_PLL_SYS_DIV_SELECT;
+ writel_relaxed(val, PLL1_SYS);
+
+ return 0;
+}
+
+static unsigned long pll8_enet_get_rate(struct clk *clk)
+{
+ u32 div = (readl_relaxed(PLL8_ENET) & BM_PLL_ENET_DIV_SELECT) >>
+ BP_PLL_ENET_DIV_SELECT;
+
+ switch (div) {
+ case 0:
+ return 25000000;
+ case 1:
+ return 50000000;
+ case 2:
+ return 100000000;
+ case 3:
+ return 125000000;
+ }
+
+ return 0;
+}
+
+static int pll8_enet_set_rate(struct clk *clk, unsigned long rate)
+{
+ u32 val, div;
+
+ switch (rate) {
+ case 25000000:
+ div = 0;
+ break;
+ case 50000000:
+ div = 1;
+ break;
+ case 100000000:
+ div = 2;
+ break;
+ case 125000000:
+ div = 3;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ val = readl_relaxed(PLL8_ENET);
+ val &= ~BM_PLL_ENET_DIV_SELECT;
+ val |= div << BP_PLL_ENET_DIV_SELECT;
+ writel_relaxed(val, PLL8_ENET);
+
+ return 0;
+}
+
+static unsigned long pll_av_get_rate(struct clk *clk)
+{
+ void __iomem *reg = (clk == &pll4_audio) ? PLL4_AUDIO : PLL5_VIDEO;
+ unsigned long parent_rate = clk_get_rate(clk->parent);
+ u32 mfn = readl_relaxed(reg + PLL_NUM_OFFSET);
+ u32 mfd = readl_relaxed(reg + PLL_DENOM_OFFSET);
+ u32 div = (readl_relaxed(reg) & BM_PLL_AV_DIV_SELECT) >>
+ BP_PLL_AV_DIV_SELECT;
+
+ return (parent_rate * div) + ((parent_rate / mfd) * mfn);
+}
+
+static int pll_av_set_rate(struct clk *clk, unsigned long rate)
+{
+ void __iomem *reg = (clk == &pll4_audio) ? PLL4_AUDIO : PLL5_VIDEO;
+ unsigned int parent_rate = clk_get_rate(clk->parent);
+ u32 val, div;
+ u32 mfn, mfd = 1000000;
+ s64 temp64;
+
+ if (rate < FREQ_650M || rate > FREQ_1300M)
+ return -EINVAL;
+
+ div = rate / parent_rate;
+ temp64 = (u64) (rate - div * parent_rate);
+ temp64 *= mfd;
+ do_div(temp64, parent_rate);
+ mfn = temp64;
+
+ val = readl_relaxed(reg);
+ val &= ~BM_PLL_AV_DIV_SELECT;
+ val |= div << BP_PLL_AV_DIV_SELECT;
+ writel_relaxed(val, reg);
+ writel_relaxed(mfn, reg + PLL_NUM_OFFSET);
+ writel_relaxed(mfd, reg + PLL_DENOM_OFFSET);
+
+ return 0;
+}
+
+static void __iomem *pll_get_div_reg_bit(struct clk *clk, u32 *bp, u32 *bm)
+{
+ void __iomem *reg;
+
+ if (clk == &pll2_bus) {
+ reg = PLL2_BUS;
+ *bp = BP_PLL_BUS_DIV_SELECT;
+ *bm = BM_PLL_BUS_DIV_SELECT;
+ } else if (clk == &pll3_usb_otg) {
+ reg = PLL3_USB_OTG;
+ *bp = BP_PLL_USB_DIV_SELECT;
+ *bm = BM_PLL_USB_DIV_SELECT;
+ } else if (clk == &pll7_usb_host) {
+ reg = PLL7_USB_HOST;
+ *bp = BP_PLL_USB_DIV_SELECT;
+ *bm = BM_PLL_USB_DIV_SELECT;
+ } else {
+ BUG();
+ }
+
+ return reg;
+}
+
+static unsigned long pll_get_rate(struct clk *clk)
+{
+ void __iomem *reg;
+ u32 div, bp, bm;
+
+ reg = pll_get_div_reg_bit(clk, &bp, &bm);
+ div = (readl_relaxed(reg) & bm) >> bp;
+
+ return (div == 1) ? clk_get_rate(clk->parent) * 22 :
+ clk_get_rate(clk->parent) * 20;
+}
+
+static int pll_set_rate(struct clk *clk, unsigned long rate)
+{
+ void __iomem *reg;
+ u32 val, div, bp, bm;
+
+ if (rate == FREQ_528M)
+ div = 1;
+ else if (rate == FREQ_480M)
+ div = 0;
+ else
+ return -EINVAL;
+
+ reg = pll_get_div_reg_bit(clk, &bp, &bm);
+ val = readl_relaxed(reg);
+ val &= ~bm;
+ val |= div << bp;
+ writel_relaxed(val, reg);
+
+ return 0;
+}
+
+#define pll2_bus_get_rate pll_get_rate
+#define pll2_bus_set_rate pll_set_rate
+#define pll3_usb_otg_get_rate pll_get_rate
+#define pll3_usb_otg_set_rate pll_set_rate
+#define pll7_usb_host_get_rate pll_get_rate
+#define pll7_usb_host_set_rate pll_set_rate
+#define pll4_audio_get_rate pll_av_get_rate
+#define pll4_audio_set_rate pll_av_set_rate
+#define pll5_video_get_rate pll_av_get_rate
+#define pll5_video_set_rate pll_av_set_rate
+#define pll6_mlb_get_rate NULL
+#define pll6_mlb_set_rate NULL
+
+#define DEF_PLL(name) \
+ static struct clk name = { \
+ .enable = pll_enable, \
+ .disable = pll_disable, \
+ .get_rate = name##_get_rate, \
+ .set_rate = name##_set_rate, \
+ .parent = &osc_clk, \
+ }
+
+DEF_PLL(pll1_sys);
+DEF_PLL(pll2_bus);
+DEF_PLL(pll3_usb_otg);
+DEF_PLL(pll4_audio);
+DEF_PLL(pll5_video);
+DEF_PLL(pll6_mlb);
+DEF_PLL(pll7_usb_host);
+DEF_PLL(pll8_enet);
+
+static unsigned long pfd_get_rate(struct clk *clk)
+{
+ u64 tmp = (u64) clk_get_rate(clk->parent) * 18;
+ u32 frac, bp_frac;
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.enable(&apbh_dma_clk);
+
+ bp_frac = clk->enable_shift - 7;
+ frac = readl_relaxed(clk->enable_reg) >> bp_frac & PFD_FRAC_MASK;
+ do_div(tmp, frac);
+
+ return tmp;
+}
+
+static int pfd_set_rate(struct clk *clk, unsigned long rate)
+{
+ u32 val, frac, bp_frac;
+ u64 tmp = (u64) clk_get_rate(clk->parent) * 18;
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.enable(&apbh_dma_clk);
+
+ /*
+ * Round up the divider so that we don't set a rate
+ * higher than what is requested
+ */
+ tmp += rate / 2;
+ do_div(tmp, rate);
+ frac = tmp;
+ frac = (frac < 12) ? 12 : frac;
+ frac = (frac > 35) ? 35 : frac;
+
+ /*
+ * The frac field always starts from 7 bits lower
+ * position of enable bit
+ */
+ bp_frac = clk->enable_shift - 7;
+ val = readl_relaxed(clk->enable_reg);
+ val &= ~(PFD_FRAC_MASK << bp_frac);
+ val |= frac << bp_frac;
+ writel_relaxed(val, clk->enable_reg);
+
+ tmp = (u64) clk_get_rate(clk->parent) * 18;
+ do_div(tmp, frac);
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.disable(&apbh_dma_clk);
+
+ return 0;
+}
+
+static unsigned long pfd_round_rate(struct clk *clk, unsigned long rate)
+{
+ u32 frac;
+ u64 tmp;
+
+ tmp = (u64) clk_get_rate(clk->parent) * 18;
+ tmp += rate / 2;
+ do_div(tmp, rate);
+ frac = tmp;
+ frac = (frac < 12) ? 12 : frac;
+ frac = (frac > 35) ? 35 : frac;
+ tmp = (u64) clk_get_rate(clk->parent) * 18;
+ do_div(tmp, frac);
+
+ return tmp;
+}
+
+static int pfd_enable(struct clk *clk)
+{
+ u32 val;
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.enable(&apbh_dma_clk);
+
+ val = readl_relaxed(clk->enable_reg);
+ val &= ~(1 << clk->enable_shift);
+ writel_relaxed(val, clk->enable_reg);
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.disable(&apbh_dma_clk);
+
+ return 0;
+}
+
+static void pfd_disable(struct clk *clk)
+{
+ u32 val;
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.enable(&apbh_dma_clk);
+
+ val = readl_relaxed(clk->enable_reg);
+ val |= 1 << clk->enable_shift;
+ writel_relaxed(val, clk->enable_reg);
+
+ if (apbh_dma_clk.usecount == 0)
+ apbh_dma_clk.disable(&apbh_dma_clk);
+}
+
+#define DEF_PFD(name, er, es, p) \
+ static struct clk name = { \
+ .enable_reg = er, \
+ .enable_shift = es, \
+ .enable = pfd_enable, \
+ .disable = pfd_disable, \
+ .get_rate = pfd_get_rate, \
+ .set_rate = pfd_set_rate, \
+ .round_rate = pfd_round_rate, \
+ .parent = p, \
+ }
+
+DEF_PFD(pll2_pfd_352m, PFD_528, PFD0, &pll2_bus);
+DEF_PFD(pll2_pfd_594m, PFD_528, PFD1, &pll2_bus);
+DEF_PFD(pll2_pfd_400m, PFD_528, PFD2, &pll2_bus);
+DEF_PFD(pll3_pfd_720m, PFD_480, PFD0, &pll3_usb_otg);
+DEF_PFD(pll3_pfd_540m, PFD_480, PFD1, &pll3_usb_otg);
+DEF_PFD(pll3_pfd_508m, PFD_480, PFD2, &pll3_usb_otg);
+DEF_PFD(pll3_pfd_454m, PFD_480, PFD3, &pll3_usb_otg);
+
+static unsigned long pll2_200m_get_rate(struct clk *clk)
+{
+ return clk_get_rate(clk->parent) / 2;
+}
+
+static struct clk pll2_200m = {
+ .parent = &pll2_pfd_400m,
+ .get_rate = pll2_200m_get_rate,
+};
+
+static unsigned long pll3_120m_get_rate(struct clk *clk)
+{
+ return clk_get_rate(clk->parent) / 4;
+}
+
+static struct clk pll3_120m = {
+ .parent = &pll3_usb_otg,
+ .get_rate = pll3_120m_get_rate,
+};
+
+static unsigned long pll3_80m_get_rate(struct clk *clk)
+{
+ return clk_get_rate(clk->parent) / 6;
+}
+
+static struct clk pll3_80m = {
+ .parent = &pll3_usb_otg,
+ .get_rate = pll3_80m_get_rate,
+};
+
+static unsigned long pll3_60m_get_rate(struct clk *clk)
+{
+ return clk_get_rate(clk->parent) / 8;
+}
+
+static struct clk pll3_60m = {
+ .parent = &pll3_usb_otg,
+ .get_rate = pll3_60m_get_rate,
+};
+
+static int pll1_sw_clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ u32 val = readl_relaxed(CCSR);
+
+ if (parent == &pll1_sys) {
+ val &= ~BM_CCSR_PLL1_SW_SEL;
+ val &= ~BM_CCSR_STEP_SEL;
+ } else if (parent == &osc_clk) {
+ val |= BM_CCSR_PLL1_SW_SEL;
+ val &= ~BM_CCSR_STEP_SEL;
+ } else if (parent == &pll2_pfd_400m) {
+ val |= BM_CCSR_PLL1_SW_SEL;
+ val |= BM_CCSR_STEP_SEL;
+ } else {
+ return -EINVAL;
+ }
+
+ writel_relaxed(val, CCSR);
+
+ return 0;
+}
+
+static struct clk pll1_sw_clk = {
+ .parent = &pll1_sys,
+ .set_parent = pll1_sw_clk_set_parent,
+};
+
+static void calc_pred_podf_dividers(u32 div, u32 *pred, u32 *podf)
+{
+ u32 min_pred, temp_pred, old_err, err;
+
+ if (div >= 512) {
+ *pred = 8;
+ *podf = 64;
+ } else if (div >= 8) {
+ min_pred = (div - 1) / 64 + 1;
+ old_err = 8;
+ for (temp_pred = 8; temp_pred >= min_pred; temp_pred--) {
+ err = div % temp_pred;
+ if (err == 0) {
+ *pred = temp_pred;
+ break;
+ }
+ err = temp_pred - err;
+ if (err < old_err) {
+ old_err = err;
+ *pred = temp_pred;
+ }
+ }
+ *podf = (div + *pred - 1) / *pred;
+ } else if (div < 8) {
+ *pred = div;
+ *podf = 1;
+ }
+}
+
+static int _clk_enable(struct clk *clk)
+{
+ u32 reg;
+ reg = readl_relaxed(clk->enable_reg);
+ reg |= 0x3 << clk->enable_shift;
+ writel_relaxed(reg, clk->enable_reg);
+
+ return 0;
+}
+
+static void _clk_disable(struct clk *clk)
+{
+ u32 reg;
+ reg = readl_relaxed(clk->enable_reg);
+ reg &= ~(0x3 << clk->enable_shift);
+ writel_relaxed(reg, clk->enable_reg);
+}
+
+struct divider {
+ struct clk *clk;
+ void __iomem *reg;
+ u32 bp_pred;
+ u32 bm_pred;
+ u32 bp_podf;
+ u32 bm_podf;
+};
+
+#define DEF_CLK_DIV1(d, c, r, b) \
+ static struct divider d = { \
+ .clk = c, \
+ .reg = r, \
+ .bp_podf = BP_##r##_##b##_PODF, \
+ .bm_podf = BM_##r##_##b##_PODF, \
+ }
+
+DEF_CLK_DIV1(arm_div, &arm_clk, CACRR, ARM);
+DEF_CLK_DIV1(ipg_div, &ipg_clk, CBCDR, IPG);
+DEF_CLK_DIV1(ahb_div, &ahb_clk, CBCDR, AHB);
+DEF_CLK_DIV1(axi_div, &axi_clk, CBCDR, AXI);
+DEF_CLK_DIV1(mmdc_ch0_axi_div, &mmdc_ch0_axi_clk, CBCDR, MMDC_CH0_AXI);
+DEF_CLK_DIV1(mmdc_ch1_axi_div, &mmdc_ch1_axi_clk, CBCDR, MMDC_CH1_AXI);
+DEF_CLK_DIV1(periph_clk2_div, &periph_clk2_clk, CBCDR, PERIPH_CLK2);
+DEF_CLK_DIV1(periph2_clk2_div, &periph2_clk2_clk, CBCDR, PERIPH2_CLK2);
+DEF_CLK_DIV1(gpu2d_core_div, &gpu2d_core_clk, CBCMR, GPU2D_CORE);
+DEF_CLK_DIV1(gpu3d_core_div, &gpu3d_core_clk, CBCMR, GPU3D_CORE);
+DEF_CLK_DIV1(gpu3d_shader_div, &gpu3d_shader_clk, CBCMR, GPU3D_SHADER);
+DEF_CLK_DIV1(ipg_perclk_div, &ipg_perclk, CSCMR1, PERCLK);
+DEF_CLK_DIV1(emi_div, &emi_clk, CSCMR1, EMI);
+DEF_CLK_DIV1(emi_slow_div, &emi_slow_clk, CSCMR1, EMI_SLOW);
+DEF_CLK_DIV1(can_div, &can1_clk, CSCMR2, CAN);
+DEF_CLK_DIV1(uart_div, &uart_clk, CSCDR1, UART);
+DEF_CLK_DIV1(usdhc1_div, &usdhc1_clk, CSCDR1, USDHC1);
+DEF_CLK_DIV1(usdhc2_div, &usdhc2_clk, CSCDR1, USDHC2);
+DEF_CLK_DIV1(usdhc3_div, &usdhc3_clk, CSCDR1, USDHC3);
+DEF_CLK_DIV1(usdhc4_div, &usdhc4_clk, CSCDR1, USDHC4);
+DEF_CLK_DIV1(vpu_div, &vpu_clk, CSCDR1, VPU_AXI);
+DEF_CLK_DIV1(hsi_tx_div, &hsi_tx_clk, CDCDR, HSI_TX);
+DEF_CLK_DIV1(ipu1_di0_pre_div, &ipu1_di0_pre_clk, CHSCCDR, IPU1_DI0_PRE);
+DEF_CLK_DIV1(ipu1_di1_pre_div, &ipu1_di1_pre_clk, CHSCCDR, IPU1_DI1_PRE);
+DEF_CLK_DIV1(ipu2_di0_pre_div, &ipu2_di0_pre_clk, CSCDR2, IPU2_DI0_PRE);
+DEF_CLK_DIV1(ipu2_di1_pre_div, &ipu2_di1_pre_clk, CSCDR2, IPU2_DI1_PRE);
+DEF_CLK_DIV1(ipu1_div, &ipu1_clk, CSCDR3, IPU1_HSP);
+DEF_CLK_DIV1(ipu2_div, &ipu2_clk, CSCDR3, IPU2_HSP);
+
+#define DEF_CLK_DIV2(d, c, r, b) \
+ static struct divider d = { \
+ .clk = c, \
+ .reg = r, \
+ .bp_pred = BP_##r##_##b##_PRED, \
+ .bm_pred = BM_##r##_##b##_PRED, \
+ .bp_podf = BP_##r##_##b##_PODF, \
+ .bm_podf = BM_##r##_##b##_PODF, \
+ }
+
+DEF_CLK_DIV2(ssi1_div, &ssi1_clk, CS1CDR, SSI1);
+DEF_CLK_DIV2(ssi3_div, &ssi3_clk, CS1CDR, SSI3);
+DEF_CLK_DIV2(esai_div, &esai_clk, CS1CDR, ESAI);
+DEF_CLK_DIV2(ssi2_div, &ssi2_clk, CS2CDR, SSI2);
+DEF_CLK_DIV2(enfc_div, &enfc_clk, CS2CDR, ENFC);
+DEF_CLK_DIV2(spdif_div, &spdif_clk, CDCDR, SPDIF);
+DEF_CLK_DIV2(asrc_serial_div, &asrc_serial_clk, CDCDR, ASRC_SERIAL);
+
+static struct divider *dividers[] = {
+ &arm_div,
+ &ipg_div,
+ &ahb_div,
+ &axi_div,
+ &mmdc_ch0_axi_div,
+ &mmdc_ch1_axi_div,
+ &periph_clk2_div,
+ &periph2_clk2_div,
+ &gpu2d_core_div,
+ &gpu3d_core_div,
+ &gpu3d_shader_div,
+ &ipg_perclk_div,
+ &emi_div,
+ &emi_slow_div,
+ &can_div,
+ &uart_div,
+ &usdhc1_div,
+ &usdhc2_div,
+ &usdhc3_div,
+ &usdhc4_div,
+ &vpu_div,
+ &hsi_tx_div,
+ &ipu1_di0_pre_div,
+ &ipu1_di1_pre_div,
+ &ipu2_di0_pre_div,
+ &ipu2_di1_pre_div,
+ &ipu1_div,
+ &ipu2_div,
+ &ssi1_div,
+ &ssi3_div,
+ &esai_div,
+ &ssi2_div,
+ &enfc_div,
+ &spdif_div,
+ &asrc_serial_div,
+};
+
+static unsigned long ldb_di_clk_get_rate(struct clk *clk)
+{
+ u32 val = readl_relaxed(CSCMR2);
+
+ val &= (clk == &ldb_di0_clk) ? BM_CSCMR2_LDB_DI0_IPU_DIV :
+ BM_CSCMR2_LDB_DI1_IPU_DIV;
+ if (val)
+ return clk_get_rate(clk->parent) / 7;
+ else
+ return clk_get_rate(clk->parent) * 2 / 7;
+}
+
+static int ldb_di_clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ unsigned long parent_rate = clk_get_rate(clk->parent);
+ u32 val = readl_relaxed(CSCMR2);
+
+ if (rate * 7 <= parent_rate + parent_rate / 20)
+ val |= BM_CSCMR2_LDB_DI0_IPU_DIV;
+ else
+ val &= ~BM_CSCMR2_LDB_DI0_IPU_DIV;
+
+ writel_relaxed(val, CSCMR2);
+
+ return 0;
+}
+
+static unsigned long ldb_di_clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ unsigned long parent_rate = clk_get_rate(clk->parent);
+
+ if (rate * 7 <= parent_rate + parent_rate / 20)
+ return parent_rate / 7;
+ else
+ return 2 * parent_rate / 7;
+}
+
+static unsigned long _clk_get_rate(struct clk *clk)
+{
+ struct divider *d;
+ u32 val, pred, podf;
+ int i, num;
+
+ if (clk == &ldb_di0_clk || clk == &ldb_di1_clk)
+ return ldb_di_clk_get_rate(clk);
+
+ num = ARRAY_SIZE(dividers);
+ for (i = 0; i < num; i++)
+ if (dividers[i]->clk == clk) {
+ d = dividers[i];
+ break;
+ }
+ if (i == num)
+ return clk_get_rate(clk->parent);
+
+ val = readl_relaxed(d->reg);
+ pred = ((val & d->bm_pred) >> d->bp_pred) + 1;
+ podf = ((val & d->bm_podf) >> d->bp_podf) + 1;
+
+ return clk_get_rate(clk->parent) / (pred * podf);
+}
+
+static int clk_busy_wait(struct clk *clk)
+{
+ int timeout = 0x100000;
+ u32 bm;
+
+ if (clk == &axi_clk)
+ bm = BM_CDHIPR_AXI_PODF_BUSY;
+ else if (clk == &ahb_clk)
+ bm = BM_CDHIPR_AHB_PODF_BUSY;
+ else if (clk == &mmdc_ch0_axi_clk)
+ bm = BM_CDHIPR_MMDC_CH0_PODF_BUSY;
+ else if (clk == &periph_clk)
+ bm = BM_CDHIPR_PERIPH_SEL_BUSY;
+ else if (clk == &arm_clk)
+ bm = BM_CDHIPR_ARM_PODF_BUSY;
+ else
+ return -EINVAL;
+
+ while ((readl_relaxed(CDHIPR) & bm) && --timeout)
+ cpu_relax();
+
+ if (unlikely(!timeout))
+ return -EBUSY;
+
+ return 0;
+}
+
+static int _clk_set_rate(struct clk *clk, unsigned long rate)
+{
+ unsigned long parent_rate = clk_get_rate(clk->parent);
+ struct divider *d;
+ u32 val, div, max_div, pred = 0, podf;
+ int i, num;
+
+ if (clk == &ldb_di0_clk || clk == &ldb_di1_clk)
+ return ldb_di_clk_set_rate(clk, rate);
+
+ num = ARRAY_SIZE(dividers);
+ for (i = 0; i < num; i++)
+ if (dividers[i]->clk == clk) {
+ d = dividers[i];
+ break;
+ }
+ if (i == num)
+ return -EINVAL;
+
+ max_div = ((d->bm_pred >> d->bp_pred) + 1) *
+ ((d->bm_pred >> d->bp_pred) + 1);
+
+ div = parent_rate / rate;
+ if (div == 0)
+ div++;
+
+ if ((parent_rate / div != rate) || div > max_div)
+ return -EINVAL;
+
+ if (d->bm_pred) {
+ calc_pred_podf_dividers(div, &pred, &podf);
+ } else {
+ pred = 1;
+ podf = div;
+ }
+
+ val = readl_relaxed(d->reg);
+ val &= ~(d->bm_pred | d->bm_podf);
+ val |= (pred - 1) << d->bp_pred | (podf - 1) << d->bp_podf;
+ writel_relaxed(val, d->reg);
+
+ if (clk == &axi_clk || clk == &ahb_clk ||
+ clk == &mmdc_ch0_axi_clk || clk == &arm_clk)
+ return clk_busy_wait(clk);
+
+ return 0;
+}
+
+static unsigned long _clk_round_rate(struct clk *clk, unsigned long rate)
+{
+ unsigned long parent_rate = clk_get_rate(clk->parent);
+ u32 div = parent_rate / rate;
+ u32 div_max, pred = 0, podf;
+ struct divider *d;
+ int i, num;
+
+ if (clk == &ldb_di0_clk || clk == &ldb_di1_clk)
+ return ldb_di_clk_round_rate(clk, rate);
+
+ num = ARRAY_SIZE(dividers);
+ for (i = 0; i < num; i++)
+ if (dividers[i]->clk == clk) {
+ d = dividers[i];
+ break;
+ }
+ if (i == num)
+ return -EINVAL;
+
+ if (div == 0 || parent_rate % rate)
+ div++;
+
+ if (d->bm_pred) {
+ calc_pred_podf_dividers(div, &pred, &podf);
+ div = pred * podf;
+ } else {
+ div_max = (d->bm_podf >> d->bp_podf) + 1;
+ if (div > div_max)
+ div = div_max;
+ }
+
+ return parent_rate / div;
+}
+
+struct multiplexer {
+ struct clk *clk;
+ void __iomem *reg;
+ u32 bp;
+ u32 bm;
+ int pnum;
+ struct clk *parents[];
+};
+
+static struct multiplexer axi_mux = {
+ .clk = &axi_clk,
+ .reg = CBCDR,
+ .bp = BP_CBCDR_AXI_SEL,
+ .bm = BM_CBCDR_AXI_SEL,
+ .parents = {
+ &periph_clk,
+ &pll2_pfd_400m,
+ &pll3_pfd_540m,
+ NULL
+ },
+};
+
+static struct multiplexer periph_mux = {
+ .clk = &periph_clk,
+ .reg = CBCDR,
+ .bp = BP_CBCDR_PERIPH_CLK_SEL,
+ .bm = BM_CBCDR_PERIPH_CLK_SEL,
+ .parents = {
+ &periph_pre_clk,
+ &periph_clk2_clk,
+ NULL
+ },
+};
+
+static struct multiplexer periph_pre_mux = {
+ .clk = &periph_pre_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_PRE_PERIPH_CLK_SEL,
+ .bm = BM_CBCMR_PRE_PERIPH_CLK_SEL,
+ .parents = {
+ &pll2_bus,
+ &pll2_pfd_400m,
+ &pll2_pfd_352m,
+ &pll2_200m,
+ NULL
+ },
+};
+
+static struct multiplexer periph_clk2_mux = {
+ .clk = &periph_clk2_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_PERIPH_CLK2_SEL,
+ .bm = BM_CBCMR_PERIPH_CLK2_SEL,
+ .parents = {
+ &pll3_usb_otg,
+ &osc_clk,
+ NULL
+ },
+};
+
+static struct multiplexer periph2_mux = {
+ .clk = &periph2_clk,
+ .reg = CBCDR,
+ .bp = BP_CBCDR_PERIPH2_CLK_SEL,
+ .bm = BM_CBCDR_PERIPH2_CLK_SEL,
+ .parents = {
+ &periph2_pre_clk,
+ &periph2_clk2_clk,
+ NULL
+ },
+};
+
+static struct multiplexer periph2_pre_mux = {
+ .clk = &periph2_pre_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_PRE_PERIPH2_CLK_SEL,
+ .bm = BM_CBCMR_PRE_PERIPH2_CLK_SEL,
+ .parents = {
+ &pll2_bus,
+ &pll2_pfd_400m,
+ &pll2_pfd_352m,
+ &pll2_200m,
+ NULL
+ },
+};
+
+static struct multiplexer periph2_clk2_mux = {
+ .clk = &periph2_clk2_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_PERIPH2_CLK2_SEL,
+ .bm = BM_CBCMR_PERIPH2_CLK2_SEL,
+ .parents = {
+ &pll3_usb_otg,
+ &osc_clk,
+ NULL
+ },
+};
+
+static struct multiplexer gpu2d_axi_mux = {
+ .clk = &gpu2d_axi_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_GPU2D_AXI_SEL,
+ .bm = BM_CBCMR_GPU2D_AXI_SEL,
+ .parents = {
+ &axi_clk,
+ &ahb_clk,
+ NULL
+ },
+};
+
+static struct multiplexer gpu3d_axi_mux = {
+ .clk = &gpu3d_axi_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_GPU3D_AXI_SEL,
+ .bm = BM_CBCMR_GPU3D_AXI_SEL,
+ .parents = {
+ &axi_clk,
+ &ahb_clk,
+ NULL
+ },
+};
+
+static struct multiplexer gpu3d_core_mux = {
+ .clk = &gpu3d_core_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_GPU3D_CORE_SEL,
+ .bm = BM_CBCMR_GPU3D_CORE_SEL,
+ .parents = {
+ &mmdc_ch0_axi_clk,
+ &pll3_usb_otg,
+ &pll2_pfd_594m,
+ &pll2_pfd_400m,
+ NULL
+ },
+};
+
+static struct multiplexer gpu3d_shader_mux = {
+ .clk = &gpu3d_shader_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_GPU3D_SHADER_SEL,
+ .bm = BM_CBCMR_GPU3D_SHADER_SEL,
+ .parents = {
+ &mmdc_ch0_axi_clk,
+ &pll3_usb_otg,
+ &pll2_pfd_594m,
+ &pll3_pfd_720m,
+ NULL
+ },
+};
+
+static struct multiplexer pcie_axi_mux = {
+ .clk = &pcie_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_PCIE_AXI_SEL,
+ .bm = BM_CBCMR_PCIE_AXI_SEL,
+ .parents = {
+ &axi_clk,
+ &ahb_clk,
+ NULL
+ },
+};
+
+static struct multiplexer vdo_axi_mux = {
+ .clk = &vdo_axi_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_VDO_AXI_SEL,
+ .bm = BM_CBCMR_VDO_AXI_SEL,
+ .parents = {
+ &axi_clk,
+ &ahb_clk,
+ NULL
+ },
+};
+
+static struct multiplexer vpu_axi_mux = {
+ .clk = &vpu_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_VPU_AXI_SEL,
+ .bm = BM_CBCMR_VPU_AXI_SEL,
+ .parents = {
+ &axi_clk,
+ &pll2_pfd_400m,
+ &pll2_pfd_352m,
+ NULL
+ },
+};
+
+static struct multiplexer gpu2d_core_mux = {
+ .clk = &gpu2d_core_clk,
+ .reg = CBCMR,
+ .bp = BP_CBCMR_GPU2D_CORE_SEL,
+ .bm = BM_CBCMR_GPU2D_CORE_SEL,
+ .parents = {
+ &axi_clk,
+ &pll3_usb_otg,
+ &pll2_pfd_352m,
+ &pll2_pfd_400m,
+ NULL
+ },
+};
+
+#define DEF_SSI_MUX(id) \
+ static struct multiplexer ssi##id##_mux = { \
+ .clk = &ssi##id##_clk, \
+ .reg = CSCMR1, \
+ .bp = BP_CSCMR1_SSI##id##_SEL, \
+ .bm = BM_CSCMR1_SSI##id##_SEL, \
+ .parents = { \
+ &pll3_pfd_508m, \
+ &pll3_pfd_454m, \
+ &pll4_audio, \
+ NULL \
+ }, \
+ }
+
+DEF_SSI_MUX(1);
+DEF_SSI_MUX(2);
+DEF_SSI_MUX(3);
+
+#define DEF_USDHC_MUX(id) \
+ static struct multiplexer usdhc##id##_mux = { \
+ .clk = &usdhc##id##_clk, \
+ .reg = CSCMR1, \
+ .bp = BP_CSCMR1_USDHC##id##_SEL, \
+ .bm = BM_CSCMR1_USDHC##id##_SEL, \
+ .parents = { \
+ &pll2_pfd_400m, \
+ &pll2_pfd_352m, \
+ NULL \
+ }, \
+ }
+
+DEF_USDHC_MUX(1);
+DEF_USDHC_MUX(2);
+DEF_USDHC_MUX(3);
+DEF_USDHC_MUX(4);
+
+static struct multiplexer emi_mux = {
+ .clk = &emi_clk,
+ .reg = CSCMR1,
+ .bp = BP_CSCMR1_EMI_SEL,
+ .bm = BM_CSCMR1_EMI_SEL,
+ .parents = {
+ &axi_clk,
+ &pll3_usb_otg,
+ &pll2_pfd_400m,
+ &pll2_pfd_352m,
+ NULL
+ },
+};
+
+static struct multiplexer emi_slow_mux = {
+ .clk = &emi_slow_clk,
+ .reg = CSCMR1,
+ .bp = BP_CSCMR1_EMI_SLOW_SEL,
+ .bm = BM_CSCMR1_EMI_SLOW_SEL,
+ .parents = {
+ &axi_clk,
+ &pll3_usb_otg,
+ &pll2_pfd_400m,
+ &pll2_pfd_352m,
+ NULL
+ },
+};
+
+static struct multiplexer esai_mux = {
+ .clk = &esai_clk,
+ .reg = CSCMR2,
+ .bp = BP_CSCMR2_ESAI_SEL,
+ .bm = BM_CSCMR2_ESAI_SEL,
+ .parents = {
+ &pll4_audio,
+ &pll3_pfd_508m,
+ &pll3_pfd_454m,
+ &pll3_usb_otg,
+ NULL
+ },
+};
+
+#define DEF_LDB_DI_MUX(id) \
+ static struct multiplexer ldb_di##id##_mux = { \
+ .clk = &ldb_di##id##_clk, \
+ .reg = CS2CDR, \
+ .bp = BP_CS2CDR_LDB_DI##id##_SEL, \
+ .bm = BM_CS2CDR_LDB_DI##id##_SEL, \
+ .parents = { \
+ &pll5_video, \
+ &pll2_pfd_352m, \
+ &pll2_pfd_400m, \
+ &pll3_pfd_540m, \
+ &pll3_usb_otg, \
+ NULL \
+ }, \
+ }
+
+DEF_LDB_DI_MUX(0);
+DEF_LDB_DI_MUX(1);
+
+static struct multiplexer enfc_mux = {
+ .clk = &enfc_clk,
+ .reg = CS2CDR,
+ .bp = BP_CS2CDR_ENFC_SEL,
+ .bm = BM_CS2CDR_ENFC_SEL,
+ .parents = {
+ &pll2_pfd_352m,
+ &pll2_bus,
+ &pll3_usb_otg,
+ &pll2_pfd_400m,
+ NULL
+ },
+};
+
+static struct multiplexer spdif_mux = {
+ .clk = &spdif_clk,
+ .reg = CDCDR,
+ .bp = BP_CDCDR_SPDIF_SEL,
+ .bm = BM_CDCDR_SPDIF_SEL,
+ .parents = {
+ &pll4_audio,
+ &pll3_pfd_508m,
+ &pll3_pfd_454m,
+ &pll3_usb_otg,
+ NULL
+ },
+};
+
+static struct multiplexer asrc_serial_mux = {
+ .clk = &asrc_serial_clk,
+ .reg = CDCDR,
+ .bp = BP_CDCDR_ASRC_SERIAL_SEL,
+ .bm = BM_CDCDR_ASRC_SERIAL_SEL,
+ .parents = {
+ &pll4_audio,
+ &pll3_pfd_508m,
+ &pll3_pfd_454m,
+ &pll3_usb_otg,
+ NULL
+ },
+};
+
+static struct multiplexer hsi_tx_mux = {
+ .clk = &hsi_tx_clk,
+ .reg = CDCDR,
+ .bp = BP_CDCDR_HSI_TX_SEL,
+ .bm = BM_CDCDR_HSI_TX_SEL,
+ .parents = {
+ &pll3_120m,
+ &pll2_pfd_400m,
+ NULL
+ },
+};
+
+#define DEF_IPU_DI_PRE_MUX(r, i, d) \
+ static struct multiplexer ipu##i##_di##d##_pre_mux = { \
+ .clk = &ipu##i##_di##d##_pre_clk, \
+ .reg = r, \
+ .bp = BP_##r##_IPU##i##_DI##d##_PRE_SEL, \
+ .bm = BM_##r##_IPU##i##_DI##d##_PRE_SEL, \
+ .parents = { \
+ &mmdc_ch0_axi_clk, \
+ &pll3_usb_otg, \
+ &pll5_video, \
+ &pll2_pfd_352m, \
+ &pll2_pfd_400m, \
+ &pll3_pfd_540m, \
+ NULL \
+ }, \
+ }
+
+DEF_IPU_DI_PRE_MUX(CHSCCDR, 1, 0);
+DEF_IPU_DI_PRE_MUX(CHSCCDR, 1, 1);
+DEF_IPU_DI_PRE_MUX(CSCDR2, 2, 0);
+DEF_IPU_DI_PRE_MUX(CSCDR2, 2, 1);
+
+#define DEF_IPU_DI_MUX(r, i, d) \
+ static struct multiplexer ipu##i##_di##d##_mux = { \
+ .clk = &ipu##i##_di##d##_clk, \
+ .reg = r, \
+ .bp = BP_##r##_IPU##i##_DI##d##_SEL, \
+ .bm = BM_##r##_IPU##i##_DI##d##_SEL, \
+ .parents = { \
+ &ipu##i##_di##d##_pre_clk, \
+ &dummy_clk, \
+ &dummy_clk, \
+ &ldb_di0_clk, \
+ &ldb_di1_clk, \
+ NULL \
+ }, \
+ }
+
+DEF_IPU_DI_MUX(CHSCCDR, 1, 0);
+DEF_IPU_DI_MUX(CHSCCDR, 1, 1);
+DEF_IPU_DI_MUX(CSCDR2, 2, 0);
+DEF_IPU_DI_MUX(CSCDR2, 2, 1);
+
+#define DEF_IPU_MUX(id) \
+ static struct multiplexer ipu##id##_mux = { \
+ .clk = &ipu##id##_clk, \
+ .reg = CSCDR3, \
+ .bp = BP_CSCDR3_IPU##id##_HSP_SEL, \
+ .bm = BM_CSCDR3_IPU##id##_HSP_SEL, \
+ .parents = { \
+ &mmdc_ch0_axi_clk, \
+ &pll2_pfd_400m, \
+ &pll3_120m, \
+ &pll3_pfd_540m, \
+ NULL \
+ }, \
+ }
+
+DEF_IPU_MUX(1);
+DEF_IPU_MUX(2);
+
+static struct multiplexer *multiplexers[] = {
+ &axi_mux,
+ &periph_mux,
+ &periph_pre_mux,
+ &periph_clk2_mux,
+ &periph2_mux,
+ &periph2_pre_mux,
+ &periph2_clk2_mux,
+ &gpu2d_axi_mux,
+ &gpu3d_axi_mux,
+ &gpu3d_core_mux,
+ &gpu3d_shader_mux,
+ &pcie_axi_mux,
+ &vdo_axi_mux,
+ &vpu_axi_mux,
+ &gpu2d_core_mux,
+ &ssi1_mux,
+ &ssi2_mux,
+ &ssi3_mux,
+ &usdhc1_mux,
+ &usdhc2_mux,
+ &usdhc3_mux,
+ &usdhc4_mux,
+ &emi_mux,
+ &emi_slow_mux,
+ &esai_mux,
+ &ldb_di0_mux,
+ &ldb_di1_mux,
+ &enfc_mux,
+ &spdif_mux,
+ &asrc_serial_mux,
+ &hsi_tx_mux,
+ &ipu1_di0_pre_mux,
+ &ipu1_di0_mux,
+ &ipu1_di1_pre_mux,
+ &ipu1_di1_mux,
+ &ipu2_di0_pre_mux,
+ &ipu2_di0_mux,
+ &ipu2_di1_pre_mux,
+ &ipu2_di1_mux,
+ &ipu1_mux,
+ &ipu2_mux,
+};
+
+static int _clk_set_parent(struct clk *clk, struct clk *parent)
+{
+ struct multiplexer *m;
+ int i, num;
+ u32 val;
+
+ num = ARRAY_SIZE(multiplexers);
+ for (i = 0; i < num; i++)
+ if (multiplexers[i]->clk == clk) {
+ m = multiplexers[i];
+ break;
+ }
+ if (i == num)
+ return -EINVAL;
+
+ i = 0;
+ while (m->parents[i]) {
+ if (parent == m->parents[i])
+ break;
+ i++;
+ }
+ if (!m->parents[i])
+ return -EINVAL;
+
+ val = readl_relaxed(m->reg);
+ val &= ~m->bm;
+ val |= i << m->bp;
+ writel_relaxed(val, m->reg);
+
+ if (clk == &periph_clk)
+ return clk_busy_wait(clk);
+
+ return 0;
+}
+
+#define DEF_NG_CLK(name, p) \
+ static struct clk name = { \
+ .get_rate = _clk_get_rate, \
+ .set_rate = _clk_set_rate, \
+ .round_rate = _clk_round_rate, \
+ .set_parent = _clk_set_parent, \
+ .parent = p, \
+ }
+
+DEF_NG_CLK(periph_clk2_clk, &osc_clk);
+DEF_NG_CLK(periph_pre_clk, &pll2_bus);
+DEF_NG_CLK(periph_clk, &periph_pre_clk);
+DEF_NG_CLK(periph2_clk2_clk, &osc_clk);
+DEF_NG_CLK(periph2_pre_clk, &pll2_bus);
+DEF_NG_CLK(periph2_clk, &periph2_pre_clk);
+DEF_NG_CLK(axi_clk, &periph_clk);
+DEF_NG_CLK(emi_clk, &axi_clk);
+DEF_NG_CLK(arm_clk, &pll1_sw_clk);
+DEF_NG_CLK(ahb_clk, &periph_clk);
+DEF_NG_CLK(ipg_clk, &ahb_clk);
+DEF_NG_CLK(ipg_perclk, &ipg_clk);
+DEF_NG_CLK(ipu1_di0_pre_clk, &pll3_pfd_540m);
+DEF_NG_CLK(ipu1_di1_pre_clk, &pll3_pfd_540m);
+DEF_NG_CLK(ipu2_di0_pre_clk, &pll3_pfd_540m);
+DEF_NG_CLK(ipu2_di1_pre_clk, &pll3_pfd_540m);
+DEF_NG_CLK(asrc_serial_clk, &pll3_usb_otg);
+
+#define DEF_CLK(name, er, es, p, s) \
+ static struct clk name = { \
+ .enable_reg = er, \
+ .enable_shift = es, \
+ .enable = _clk_enable, \
+ .disable = _clk_disable, \
+ .get_rate = _clk_get_rate, \
+ .set_rate = _clk_set_rate, \
+ .round_rate = _clk_round_rate, \
+ .set_parent = _clk_set_parent, \
+ .parent = p, \
+ .secondary = s, \
+ }
+
+DEF_CLK(aips_tz1_clk, CCGR0, CG0, &ahb_clk, NULL);
+DEF_CLK(aips_tz2_clk, CCGR0, CG1, &ahb_clk, NULL);
+DEF_CLK(apbh_dma_clk, CCGR0, CG2, &ahb_clk, NULL);
+DEF_CLK(asrc_clk, CCGR0, CG3, &pll4_audio, NULL);
+DEF_CLK(can1_serial_clk, CCGR0, CG8, &pll3_usb_otg, NULL);
+DEF_CLK(can1_clk, CCGR0, CG7, &pll3_usb_otg, &can1_serial_clk);
+DEF_CLK(can2_serial_clk, CCGR0, CG10, &pll3_usb_otg, NULL);
+DEF_CLK(can2_clk, CCGR0, CG9, &pll3_usb_otg, &can2_serial_clk);
+DEF_CLK(ecspi1_clk, CCGR1, CG0, &pll3_60m, NULL);
+DEF_CLK(ecspi2_clk, CCGR1, CG1, &pll3_60m, NULL);
+DEF_CLK(ecspi3_clk, CCGR1, CG2, &pll3_60m, NULL);
+DEF_CLK(ecspi4_clk, CCGR1, CG3, &pll3_60m, NULL);
+DEF_CLK(ecspi5_clk, CCGR1, CG4, &pll3_60m, NULL);
+DEF_CLK(enet_clk, CCGR1, CG5, &ipg_clk, NULL);
+DEF_CLK(esai_clk, CCGR1, CG8, &pll3_usb_otg, NULL);
+DEF_CLK(gpt_serial_clk, CCGR1, CG11, &ipg_perclk, NULL);
+DEF_CLK(gpt_clk, CCGR1, CG10, &ipg_perclk, &gpt_serial_clk);
+DEF_CLK(gpu2d_core_clk, CCGR1, CG12, &pll2_pfd_352m, &gpu2d_axi_clk);
+DEF_CLK(gpu3d_core_clk, CCGR1, CG13, &pll2_pfd_594m, &gpu3d_axi_clk);
+DEF_CLK(gpu3d_shader_clk, CCGR1, CG13, &pll3_pfd_720m, &gpu3d_axi_clk);
+DEF_CLK(hdmi_iahb_clk, CCGR2, CG0, &ahb_clk, NULL);
+DEF_CLK(hdmi_isfr_clk, CCGR2, CG2, &pll3_pfd_540m, &hdmi_iahb_clk);
+DEF_CLK(i2c1_clk, CCGR2, CG3, &ipg_perclk, NULL);
+DEF_CLK(i2c2_clk, CCGR2, CG4, &ipg_perclk, NULL);
+DEF_CLK(i2c3_clk, CCGR2, CG5, &ipg_perclk, NULL);
+DEF_CLK(iim_clk, CCGR2, CG6, &ipg_clk, NULL);
+DEF_CLK(enfc_clk, CCGR2, CG7, &pll2_pfd_352m, NULL);
+DEF_CLK(ipu1_clk, CCGR3, CG0, &mmdc_ch0_axi_clk, NULL);
+DEF_CLK(ipu1_di0_clk, CCGR3, CG1, &ipu1_di0_pre_clk, NULL);
+DEF_CLK(ipu1_di1_clk, CCGR3, CG2, &ipu1_di1_pre_clk, NULL);
+DEF_CLK(ipu2_clk, CCGR3, CG3, &mmdc_ch0_axi_clk, NULL);
+DEF_CLK(ipu2_di0_clk, CCGR3, CG4, &ipu2_di0_pre_clk, NULL);
+DEF_CLK(ipu2_di1_clk, CCGR3, CG5, &ipu2_di1_pre_clk, NULL);
+DEF_CLK(ldb_di0_clk, CCGR3, CG6, &pll3_pfd_540m, NULL);
+DEF_CLK(ldb_di1_clk, CCGR3, CG7, &pll3_pfd_540m, NULL);
+DEF_CLK(hsi_tx_clk, CCGR3, CG8, &pll2_pfd_400m, NULL);
+DEF_CLK(mlb_clk, CCGR3, CG9, &pll6_mlb, NULL);
+DEF_CLK(mmdc_ch0_ipg_clk, CCGR3, CG12, &ipg_clk, NULL);
+DEF_CLK(mmdc_ch0_axi_clk, CCGR3, CG10, &periph_clk, &mmdc_ch0_ipg_clk);
+DEF_CLK(mmdc_ch1_ipg_clk, CCGR3, CG13, &ipg_clk, NULL);
+DEF_CLK(mmdc_ch1_axi_clk, CCGR3, CG11, &periph2_clk, &mmdc_ch1_ipg_clk);
+DEF_CLK(openvg_axi_clk, CCGR3, CG13, &axi_clk, NULL);
+DEF_CLK(pwm1_clk, CCGR4, CG8, &ipg_perclk, NULL);
+DEF_CLK(pwm2_clk, CCGR4, CG9, &ipg_perclk, NULL);
+DEF_CLK(pwm3_clk, CCGR4, CG10, &ipg_perclk, NULL);
+DEF_CLK(pwm4_clk, CCGR4, CG11, &ipg_perclk, NULL);
+DEF_CLK(gpmi_bch_apb_clk, CCGR4, CG12, &usdhc3_clk, NULL);
+DEF_CLK(gpmi_bch_clk, CCGR4, CG13, &usdhc4_clk, &gpmi_bch_apb_clk);
+DEF_CLK(gpmi_apb_clk, CCGR4, CG15, &usdhc3_clk, &gpmi_bch_clk);
+DEF_CLK(gpmi_io_clk, CCGR4, CG14, &enfc_clk, &gpmi_apb_clk);
+DEF_CLK(sdma_clk, CCGR5, CG3, &ahb_clk, NULL);
+DEF_CLK(spba_clk, CCGR5, CG6, &ipg_clk, NULL);
+DEF_CLK(spdif_clk, CCGR5, CG7, &pll3_usb_otg, &spba_clk);
+DEF_CLK(ssi1_clk, CCGR5, CG9, &pll3_pfd_508m, NULL);
+DEF_CLK(ssi2_clk, CCGR5, CG10, &pll3_pfd_508m, NULL);
+DEF_CLK(ssi3_clk, CCGR5, CG11, &pll3_pfd_508m, NULL);
+DEF_CLK(uart_serial_clk, CCGR5, CG13, &pll3_usb_otg, NULL);
+DEF_CLK(uart_clk, CCGR5, CG12, &pll3_80m, &uart_serial_clk);
+DEF_CLK(usboh3_clk, CCGR6, CG0, &ipg_clk, NULL);
+DEF_CLK(usdhc1_clk, CCGR6, CG1, &pll2_pfd_400m, NULL);
+DEF_CLK(usdhc2_clk, CCGR6, CG2, &pll2_pfd_400m, NULL);
+DEF_CLK(usdhc3_clk, CCGR6, CG3, &pll2_pfd_400m, NULL);
+DEF_CLK(usdhc4_clk, CCGR6, CG4, &pll2_pfd_400m, NULL);
+DEF_CLK(emi_slow_clk, CCGR6, CG5, &axi_clk, NULL);
+DEF_CLK(vdo_axi_clk, CCGR6, CG6, &axi_clk, NULL);
+DEF_CLK(vpu_clk, CCGR6, CG7, &axi_clk, NULL);
+
+static int pcie_clk_enable(struct clk *clk)
+{
+ u32 val;
+
+ val = readl_relaxed(PLL8_ENET);
+ val |= BM_PLL_ENET_EN_PCIE;
+ writel_relaxed(val, PLL8_ENET);
+
+ return _clk_enable(clk);
+}
+
+static void pcie_clk_disable(struct clk *clk)
+{
+ u32 val;
+
+ _clk_disable(clk);
+
+ val = readl_relaxed(PLL8_ENET);
+ val &= BM_PLL_ENET_EN_PCIE;
+ writel_relaxed(val, PLL8_ENET);
+}
+
+static struct clk pcie_clk = {
+ .enable_reg = CCGR4,
+ .enable_shift = CG0,
+ .enable = pcie_clk_enable,
+ .disable = pcie_clk_disable,
+ .set_parent = _clk_set_parent,
+ .parent = &axi_clk,
+ .secondary = &pll8_enet,
+};
+
+static int sata_clk_enable(struct clk *clk)
+{
+ u32 val;
+
+ val = readl_relaxed(PLL8_ENET);
+ val |= BM_PLL_ENET_EN_SATA;
+ writel_relaxed(val, PLL8_ENET);
+
+ return _clk_enable(clk);
+}
+
+static void sata_clk_disable(struct clk *clk)
+{
+ u32 val;
+
+ _clk_disable(clk);
+
+ val = readl_relaxed(PLL8_ENET);
+ val &= BM_PLL_ENET_EN_SATA;
+ writel_relaxed(val, PLL8_ENET);
+}
+
+static struct clk sata_clk = {
+ .enable_reg = CCGR5,
+ .enable_shift = CG2,
+ .enable = sata_clk_enable,
+ .disable = sata_clk_disable,
+ .parent = &ipg_clk,
+ .secondary = &pll8_enet,
+};
+
+#define _REGISTER_CLOCK(d, n, c) \
+ { \
+ .dev_id = d, \
+ .con_id = n, \
+ .clk = &c, \
+ }
+
+static struct clk_lookup lookups[] = {
+ _REGISTER_CLOCK("2020000.uart", NULL, uart_clk),
+ _REGISTER_CLOCK("21e8000.uart", NULL, uart_clk),
+ _REGISTER_CLOCK("21ec000.uart", NULL, uart_clk),
+ _REGISTER_CLOCK("21f0000.uart", NULL, uart_clk),
+ _REGISTER_CLOCK("21f4000.uart", NULL, uart_clk),
+ _REGISTER_CLOCK("2188000.enet", NULL, enet_clk),
+ _REGISTER_CLOCK("2190000.usdhc", NULL, usdhc1_clk),
+ _REGISTER_CLOCK("2194000.usdhc", NULL, usdhc2_clk),
+ _REGISTER_CLOCK("2198000.usdhc", NULL, usdhc3_clk),
+ _REGISTER_CLOCK("219c000.usdhc", NULL, usdhc4_clk),
+ _REGISTER_CLOCK("21a0000.i2c", NULL, i2c1_clk),
+ _REGISTER_CLOCK("21a4000.i2c", NULL, i2c2_clk),
+ _REGISTER_CLOCK("21a8000.i2c", NULL, i2c3_clk),
+ _REGISTER_CLOCK("2008000.ecspi", NULL, ecspi1_clk),
+ _REGISTER_CLOCK("200c000.ecspi", NULL, ecspi2_clk),
+ _REGISTER_CLOCK("2010000.ecspi", NULL, ecspi3_clk),
+ _REGISTER_CLOCK("2014000.ecspi", NULL, ecspi4_clk),
+ _REGISTER_CLOCK("2018000.ecspi", NULL, ecspi5_clk),
+ _REGISTER_CLOCK("20ec000.sdma", NULL, sdma_clk),
+ _REGISTER_CLOCK("20bc000.wdog", NULL, dummy_clk),
+ _REGISTER_CLOCK("20c0000.wdog", NULL, dummy_clk),
+ _REGISTER_CLOCK(NULL, "ckih", ckih_clk),
+ _REGISTER_CLOCK(NULL, "ckil_clk", ckil_clk),
+ _REGISTER_CLOCK(NULL, "aips_tz1_clk", aips_tz1_clk),
+ _REGISTER_CLOCK(NULL, "aips_tz2_clk", aips_tz2_clk),
+ _REGISTER_CLOCK(NULL, "asrc_clk", asrc_clk),
+ _REGISTER_CLOCK(NULL, "can2_clk", can2_clk),
+ _REGISTER_CLOCK(NULL, "hdmi_isfr_clk", hdmi_isfr_clk),
+ _REGISTER_CLOCK(NULL, "iim_clk", iim_clk),
+ _REGISTER_CLOCK(NULL, "mlb_clk", mlb_clk),
+ _REGISTER_CLOCK(NULL, "openvg_axi_clk", openvg_axi_clk),
+ _REGISTER_CLOCK(NULL, "pwm1_clk", pwm1_clk),
+ _REGISTER_CLOCK(NULL, "pwm2_clk", pwm2_clk),
+ _REGISTER_CLOCK(NULL, "pwm3_clk", pwm3_clk),
+ _REGISTER_CLOCK(NULL, "pwm4_clk", pwm4_clk),
+ _REGISTER_CLOCK(NULL, "gpmi_io_clk", gpmi_io_clk),
+ _REGISTER_CLOCK(NULL, "usboh3_clk", usboh3_clk),
+ _REGISTER_CLOCK(NULL, "sata_clk", sata_clk),
+};
+
+int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode)
+{
+ u32 val = readl_relaxed(CLPCR);
+
+ val &= ~BM_CLPCR_LPM;
+ switch (mode) {
+ case WAIT_CLOCKED:
+ break;
+ case WAIT_UNCLOCKED:
+ val |= 0x1 << BP_CLPCR_LPM;
+ break;
+ case STOP_POWER_ON:
+ val |= 0x2 << BP_CLPCR_LPM;
+ break;
+ case WAIT_UNCLOCKED_POWER_OFF:
+ val |= 0x1 << BP_CLPCR_LPM;
+ val &= ~BM_CLPCR_VSTBY;
+ val &= ~BM_CLPCR_SBYOS;
+ val |= BM_CLPCR_BYP_MMDC_CH1_LPM_HS;
+ break;
+ case STOP_POWER_OFF:
+ val |= 0x2 << BP_CLPCR_LPM;
+ val |= 0x3 << BP_CLPCR_STBY_COUNT;
+ val |= BM_CLPCR_VSTBY;
+ val |= BM_CLPCR_SBYOS;
+ val |= BM_CLPCR_BYP_MMDC_CH1_LPM_HS;
+ break;
+ default:
+ return -EINVAL;
+ }
+ writel_relaxed(val, CLPCR);
+
+ return 0;
+}
+
+static struct map_desc imx6q_clock_desc[] = {
+ imx_map_entry(MX6Q, CCM, MT_DEVICE),
+ imx_map_entry(MX6Q, ANATOP, MT_DEVICE),
+};
+
+int __init mx6q_clocks_init(void)
+{
+ struct device_node *np;
+ void __iomem *base;
+ int i, irq;
+
+ iotable_init(imx6q_clock_desc, ARRAY_SIZE(imx6q_clock_desc));
+
+ /* retrieve the freqency of fixed clocks from device tree */
+ for_each_compatible_node(np, NULL, "fixed-clock") {
+ u32 rate;
+ if (of_property_read_u32(np, "clock-frequency", &rate))
+ continue;
+
+ if (of_device_is_compatible(np, "fsl,imx6q-clkl"))
+ external_low_reference = rate;
+ else if (of_device_is_compatible(np, "fsl,imx6q-clkh"))
+ external_high_reference = rate;
+ else if (of_device_is_compatible(np, "fsl,imx6q-osc"))
+ oscillator_reference = rate;
+ }
+
+ for (i = 0; i < ARRAY_SIZE(lookups); i++)
+ clkdev_add(&lookups[i]);
+
+ /* only keep necessary clocks on */
+ writel_relaxed(0x3 << CG0 | 0x3 << CG1 | 0x3 << CG2, CCGR0);
+ writel_relaxed(0x3 << CG8 | 0x3 << CG9 | 0x3 << CG10, CCGR2);
+ writel_relaxed(0x3 << CG10 | 0x3 << CG12, CCGR3);
+ writel_relaxed(0x3 << CG4 | 0x3 << CG6 | 0x3 << CG7, CCGR4);
+ writel_relaxed(0x3 << CG0, CCGR5);
+ writel_relaxed(0, CCGR6);
+ writel_relaxed(0, CCGR7);
+
+ clk_enable(&uart_clk);
+ clk_enable(&mmdc_ch0_axi_clk);
+
+ clk_set_rate(&pll4_audio, FREQ_650M);
+ clk_set_rate(&pll5_video, FREQ_650M);
+ clk_set_parent(&ipu1_di0_clk, &ipu1_di0_pre_clk);
+ clk_set_parent(&ipu1_di0_pre_clk, &pll5_video);
+ clk_set_parent(&gpu3d_shader_clk, &pll2_pfd_594m);
+ clk_set_rate(&gpu3d_shader_clk, FREQ_594M);
+ clk_set_parent(&gpu3d_core_clk, &mmdc_ch0_axi_clk);
+ clk_set_rate(&gpu3d_core_clk, FREQ_528M);
+ clk_set_parent(&asrc_serial_clk, &pll3_usb_otg);
+ clk_set_rate(&asrc_serial_clk, 1500000);
+ clk_set_rate(&enfc_clk, 11000000);
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpt");
+ base = of_iomap(np, 0);
+ WARN_ON(!base);
+ irq = irq_of_parse_and_map(np, 0);
+ mxc_timer_init(&gpt_clk, base, irq);
+
+ return 0;
+}
diff --git a/arch/arm/mach-imx/gpc.c b/arch/arm/mach-imx/gpc.c
new file mode 100644
index 0000000..e1537f9
--- /dev/null
+++ b/arch/arm/mach-imx/gpc.c
@@ -0,0 +1,113 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later@the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/io.h>
+#include <linux/irq.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <asm/hardware/gic.h>
+
+#define GPC_IMR1 0x008
+#define GPC_PGC_CPU_PDN 0x2a0
+
+#define IMR_NUM 4
+
+static void __iomem *gpc_base;
+static u32 gpc_wake_irqs[IMR_NUM];
+static u32 gpc_saved_imrs[IMR_NUM];
+
+void imx_gpc_pre_suspend(void)
+{
+ void __iomem *reg_imr1 = gpc_base + GPC_IMR1;
+ int i;
+
+ /* Tell GPC to power off ARM core when suspend */
+ writel_relaxed(0x1, gpc_base + GPC_PGC_CPU_PDN);
+
+ for (i = 0; i < IMR_NUM; i++) {
+ gpc_saved_imrs[i] = readl_relaxed(reg_imr1 + i * 4);
+ writel_relaxed(~gpc_wake_irqs[i], reg_imr1 + i * 4);
+ }
+}
+
+void imx_gpc_post_resume(void)
+{
+ void __iomem *reg_imr1 = gpc_base + GPC_IMR1;
+ int i;
+
+ /* Keep ARM core powered on for other low-power modes */
+ writel_relaxed(0x0, gpc_base + GPC_PGC_CPU_PDN);
+
+ for (i = 0; i < IMR_NUM; i++)
+ writel_relaxed(gpc_saved_imrs[i], reg_imr1 + i * 4);
+}
+
+static int imx_gpc_irq_set_wake(struct irq_data *d, unsigned int on)
+{
+ unsigned int idx = d->irq / 32 - 1;
+ u32 mask;
+
+ /* Sanity check for SPI irq */
+ if (d->irq < 32)
+ return -EINVAL;
+
+ mask = 1 << d->irq % 32;
+ gpc_wake_irqs[idx] = on ? gpc_wake_irqs[idx] | mask :
+ gpc_wake_irqs[idx] & ~mask;
+
+ return 0;
+}
+
+static void imx_gpc_irq_unmask(struct irq_data *d)
+{
+ void __iomem *reg;
+ u32 val;
+
+ /* Sanity check for SPI irq */
+ if (d->irq < 32)
+ return;
+
+ reg = gpc_base + GPC_IMR1 + (d->irq / 32 - 1) * 4;
+ val = readl_relaxed(reg);
+ val &= ~(1 << d->irq % 32);
+ writel_relaxed(val, reg);
+}
+
+static void imx_gpc_irq_mask(struct irq_data *d)
+{
+ void __iomem *reg;
+ u32 val;
+
+ /* Sanity check for SPI irq */
+ if (d->irq < 32)
+ return;
+
+ reg = gpc_base + GPC_IMR1 + (d->irq / 32 - 1) * 4;
+ val = readl_relaxed(reg);
+ val |= 1 << (d->irq % 32);
+ writel_relaxed(val, reg);
+}
+
+void __init imx_gpc_init(void)
+{
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-gpc");
+ gpc_base = of_iomap(np, 0);
+ WARN_ON(!gpc_base);
+
+ /* Register GPC as the secondary interrupt controller behind GIC */
+ gic_arch_extn.irq_mask = imx_gpc_irq_mask;
+ gic_arch_extn.irq_unmask = imx_gpc_irq_unmask;
+ gic_arch_extn.irq_set_wake = imx_gpc_irq_set_wake;
+}
diff --git a/arch/arm/mach-imx/mmdc.c b/arch/arm/mach-imx/mmdc.c
new file mode 100644
index 0000000..c461e98
--- /dev/null
+++ b/arch/arm/mach-imx/mmdc.c
@@ -0,0 +1,72 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/of_device.h>
+
+#define MMDC_MAPSR 0x404
+#define BP_MMDC_MAPSR_PSD 0
+#define BP_MMDC_MAPSR_PSS 4
+
+static int __devinit imx_mmdc_probe(struct platform_device *pdev)
+{
+ struct device_node *np = pdev->dev.of_node;
+ void __iomem *mmdc_base, *reg;
+ u32 val;
+ int timeout = 0x400;
+
+ mmdc_base = of_iomap(np, 0);
+ WARN_ON(!mmdc_base);
+
+ reg = mmdc_base + MMDC_MAPSR;
+
+ /* Enable automatic power saving */
+ val = readl_relaxed(reg);
+ val &= ~(1 << BP_MMDC_MAPSR_PSD);
+ writel_relaxed(val, reg);
+
+ /* Ensure it's successfully enabled */
+ while (!(readl_relaxed(reg) & 1 << BP_MMDC_MAPSR_PSS) && --timeout)
+ cpu_relax();
+
+ if (unlikely(!timeout)) {
+ pr_warn("%s: failed to enable automatic power saving\n",
+ __func__);
+ return -EBUSY;
+ }
+
+ return 0;
+}
+
+static struct of_device_id imx_mmdc_dt_ids[] = {
+ { .compatible = "fsl,imx6q-mmdc", },
+ { /* sentinel */ }
+};
+
+static struct platform_driver imx_mmdc_driver = {
+ .driver = {
+ .name = "imx-mmdc",
+ .owner = THIS_MODULE,
+ .of_match_table = imx_mmdc_dt_ids,
+ },
+ .probe = imx_mmdc_probe,
+};
+
+static int __init imx_mmdc_init(void)
+{
+ return platform_driver_register(&imx_mmdc_driver);
+}
+postcore_initcall(imx_mmdc_init);
diff --git a/arch/arm/mach-imx/src.c b/arch/arm/mach-imx/src.c
new file mode 100644
index 0000000..36cacbd
--- /dev/null
+++ b/arch/arm/mach-imx/src.c
@@ -0,0 +1,49 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later@the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <asm/unified.h>
+
+#define SRC_SCR 0x000
+#define SRC_GPR1 0x020
+#define BP_SRC_SCR_CORE1_RST 14
+#define BP_SRC_SCR_CORE1_ENABLE 22
+
+static void __iomem *src_base;
+
+void imx_enable_cpu(int cpu, bool enable)
+{
+ u32 mask, val;
+
+ mask = 1 << (BP_SRC_SCR_CORE1_ENABLE + cpu - 1);
+ val = readl_relaxed(src_base + SRC_SCR);
+ val = enable ? val | mask : val & ~mask;
+ writel_relaxed(val, src_base + SRC_SCR);
+}
+
+void imx_set_cpu_jump(int cpu, void *jump_addr)
+{
+ writel_relaxed(BSYM(virt_to_phys(jump_addr)),
+ src_base + SRC_GPR1 + cpu * 8);
+}
+
+void __init imx_src_init(void)
+{
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "fsl,imx6q-src");
+ src_base = of_iomap(np, 0);
+ WARN_ON(!src_base);
+}
--
1.7.4.1
^ permalink raw reply related
* [PATCH v4 5/7] arm/imx6q: add smp and cpu hotplug support
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
It adds smp and cpu hotplug support for imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/Kconfig | 1 +
arch/arm/mach-imx/Makefile | 5 ++
arch/arm/mach-imx/head-v7.S | 71 ++++++++++++++++++++++++++
arch/arm/mach-imx/hotplug.c | 44 ++++++++++++++++
arch/arm/mach-imx/localtimer.c | 35 +++++++++++++
arch/arm/mach-imx/platsmp.c | 85 +++++++++++++++++++++++++++++++
arch/arm/plat-mxc/include/mach/common.h | 5 ++
7 files changed, 246 insertions(+), 0 deletions(-)
create mode 100644 arch/arm/mach-imx/head-v7.S
create mode 100644 arch/arm/mach-imx/hotplug.c
create mode 100644 arch/arm/mach-imx/localtimer.c
create mode 100644 arch/arm/mach-imx/platsmp.c
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index 7555410..d52fe3d 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -610,6 +610,7 @@ config SOC_IMX6Q
bool "i.MX6 Quad support"
select ARM_GIC
select CPU_V7
+ select HAVE_ARM_SCU
select HAVE_IMX_GPC
select HAVE_IMX_MMDC
select HAVE_IMX_SRC
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index c71e3c5..67aba68 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -66,4 +66,9 @@ obj-$(CONFIG_DEBUG_LL) += lluart.o
obj-$(CONFIG_HAVE_IMX_GPC) += gpc.o
obj-$(CONFIG_HAVE_IMX_MMDC) += mmdc.o
obj-$(CONFIG_HAVE_IMX_SRC) += src.o
+obj-$(CONFIG_CPU_V7) += head-v7.o
+AFLAGS_head-v7.o :=-Wa,-march=armv7-a
+obj-$(CONFIG_SMP) += platsmp.o
+obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
+obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o
diff --git a/arch/arm/mach-imx/head-v7.S b/arch/arm/mach-imx/head-v7.S
new file mode 100644
index 0000000..ede908b
--- /dev/null
+++ b/arch/arm/mach-imx/head-v7.S
@@ -0,0 +1,71 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/linkage.h>
+#include <linux/init.h>
+#include <asm/hardware/cache-l2x0.h>
+
+ .section ".text.head", "ax"
+ __CPUINIT
+
+/*
+ * The secondary kernel init calls v7_flush_dcache_all before it enables
+ * the L1; however, the L1 comes out of reset in an undefined state, so
+ * the clean + invalidate performed by v7_flush_dcache_all causes a bunch
+ * of cache lines with uninitialized data and uninitialized tags to get
+ * written out to memory, which does really unpleasant things to the main
+ * processor. We fix this by performing an invalidate, rather than a
+ * clean + invalidate, before jumping into the kernel.
+ *
+ * This funciton is cloned from arch/arm/mach-tegra/headsmp.S, and needs
+ * to be called for both secondary cores startup and primary core resume
+ * procedures. Ideally, it should be moved into arch/arm/mm/cache-v7.S.
+ */
+ENTRY(v7_invalidate_l1)
+ mov r0, #0
+ mcr p15, 2, r0, c0, c0, 0
+ mrc p15, 1, r0, c0, c0, 0
+
+ ldr r1, =0x7fff
+ and r2, r1, r0, lsr #13
+
+ ldr r1, =0x3ff
+
+ and r3, r1, r0, lsr #3 @ NumWays - 1
+ add r2, r2, #1 @ NumSets
+
+ and r0, r0, #0x7
+ add r0, r0, #4 @ SetShift
+
+ clz r1, r3 @ WayShift
+ add r4, r3, #1 @ NumWays
+1: sub r2, r2, #1 @ NumSets--
+ mov r3, r4 @ Temp = NumWays
+2: subs r3, r3, #1 @ Temp--
+ mov r5, r3, lsl r1
+ mov r6, r2, lsl r0
+ orr r5, r5, r6 @ Reg = (Temp<<WayShift)|(NumSets<<SetShift)
+ mcr p15, 0, r5, c7, c6, 2
+ bgt 2b
+ cmp r2, #0
+ bgt 1b
+ dsb
+ isb
+ mov pc, lr
+ENDPROC(v7_invalidate_l1)
+
+#ifdef CONFIG_SMP
+ENTRY(v7_secondary_startup)
+ bl v7_invalidate_l1
+ b secondary_startup
+ENDPROC(v7_secondary_startup)
+#endif
diff --git a/arch/arm/mach-imx/hotplug.c b/arch/arm/mach-imx/hotplug.c
new file mode 100644
index 0000000..89493ab
--- /dev/null
+++ b/arch/arm/mach-imx/hotplug.c
@@ -0,0 +1,44 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later@the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/errno.h>
+#include <asm/cacheflush.h>
+#include <mach/common.h>
+
+int platform_cpu_kill(unsigned int cpu)
+{
+ return 1;
+}
+
+/*
+ * platform-specific code to shutdown a CPU
+ *
+ * Called with IRQs disabled
+ */
+void platform_cpu_die(unsigned int cpu)
+{
+ flush_cache_all();
+ imx_enable_cpu(cpu, false);
+ cpu_do_idle();
+
+ /* We should never return from idle */
+ panic("cpu %d unexpectedly exit from shutdown\n", cpu);
+}
+
+int platform_cpu_disable(unsigned int cpu)
+{
+ /*
+ * we don't allow CPU 0 to be shutdown (it is still too special
+ * e.g. clock tick interrupts)
+ */
+ return cpu == 0 ? -EPERM : 0;
+}
diff --git a/arch/arm/mach-imx/localtimer.c b/arch/arm/mach-imx/localtimer.c
new file mode 100644
index 0000000..3a16351
--- /dev/null
+++ b/arch/arm/mach-imx/localtimer.c
@@ -0,0 +1,35 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/clockchips.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <asm/smp_twd.h>
+
+/*
+ * Setup the local clock events for a CPU.
+ */
+int __cpuinit local_timer_setup(struct clock_event_device *evt)
+{
+ struct device_node *np;
+
+ np = of_find_compatible_node(NULL, NULL, "arm,smp-twd");
+ if (!twd_base) {
+ twd_base = of_iomap(np, 0);
+ WARN_ON(!twd_base);
+ }
+ evt->irq = irq_of_parse_and_map(np, 0);
+ twd_timer_setup(evt);
+
+ return 0;
+}
diff --git a/arch/arm/mach-imx/platsmp.c b/arch/arm/mach-imx/platsmp.c
new file mode 100644
index 0000000..ab98c6f
--- /dev/null
+++ b/arch/arm/mach-imx/platsmp.c
@@ -0,0 +1,85 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/smp.h>
+#include <asm/page.h>
+#include <asm/smp_scu.h>
+#include <asm/hardware/gic.h>
+#include <asm/mach/map.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+
+static void __iomem *scu_base;
+
+static struct map_desc scu_io_desc __initdata = {
+ /* .virtual and .pfn are run-time assigned */
+ .length = SZ_4K,
+ .type = MT_DEVICE,
+};
+
+void __init imx_scu_map_io(void)
+{
+ unsigned long base;
+
+ /* Get SCU base */
+ asm("mrc p15, 4, %0, c15, c0, 0" : "=r" (base));
+
+ scu_io_desc.virtual = IMX_IO_P2V(base);
+ scu_io_desc.pfn = __phys_to_pfn(base);
+ iotable_init(&scu_io_desc, 1);
+
+ scu_base = IMX_IO_ADDRESS(base);
+}
+
+void __cpuinit platform_secondary_init(unsigned int cpu)
+{
+ /*
+ * if any interrupts are already enabled for the primary
+ * core (e.g. timer irq), then they will not have been enabled
+ * for us: do so
+ */
+ gic_secondary_init(0);
+}
+
+int __cpuinit boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ imx_set_cpu_jump(cpu, v7_secondary_startup);
+ imx_enable_cpu(cpu, true);
+ return 0;
+}
+
+/*
+ * Initialise the CPU possible map early - this describes the CPUs
+ * which may be present or become present in the system.
+ */
+void __init smp_init_cpus(void)
+{
+ int i, ncores;
+
+ ncores = scu_get_core_count(scu_base);
+
+ for (i = 0; i < ncores; i++)
+ set_cpu_possible(i, true);
+
+ set_smp_cross_call(gic_raise_softirq);
+}
+
+void imx_smp_prepare(void)
+{
+ scu_enable(scu_base);
+}
+
+void __init platform_smp_prepare_cpus(unsigned int max_cpus)
+{
+ imx_smp_prepare();
+}
diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
index 988fa9a..855c214 100644
--- a/arch/arm/plat-mxc/include/mach/common.h
+++ b/arch/arm/plat-mxc/include/mach/common.h
@@ -88,4 +88,9 @@ void gic_handle_irq(struct pt_regs *);
#define imx53_handle_irq tzic_handle_irq
#define imx6q_handle_irq gic_handle_irq
+extern void imx_enable_cpu(int cpu, bool enable);
+extern void imx_set_cpu_jump(int cpu, void *jump_addr);
+#ifdef CONFIG_SMP
+extern void v7_secondary_startup(void);
+#endif
#endif
--
1.7.4.1
^ permalink raw reply related
* [PATCH v4 6/7] arm/imx6q: add device tree machine support
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
It adds generic device tree based machine support for imx6q.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/Makefile | 2 +-
arch/arm/mach-imx/mach-imx6q.c | 84 +++++++++++++++++++++++++++++++
arch/arm/mm/Kconfig | 2 +-
arch/arm/plat-mxc/include/mach/common.h | 13 +++++
4 files changed, 99 insertions(+), 2 deletions(-)
create mode 100644 arch/arm/mach-imx/mach-imx6q.c
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 67aba68..31c8602 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -71,4 +71,4 @@ AFLAGS_head-v7.o :=-Wa,-march=armv7-a
obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
-obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o
+obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o
diff --git a/arch/arm/mach-imx/mach-imx6q.c b/arch/arm/mach-imx/mach-imx6q.c
new file mode 100644
index 0000000..8bf5fa3
--- /dev/null
+++ b/arch/arm/mach-imx/mach-imx6q.c
@@ -0,0 +1,84 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/of.h>
+#include <linux/of_irq.h>
+#include <linux/of_platform.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <asm/hardware/gic.h>
+#include <asm/mach/arch.h>
+#include <asm/mach/time.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+
+static void __init imx6q_init_machine(void)
+{
+ of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
+
+ imx6q_pm_init();
+}
+
+static void __init imx6q_map_io(void)
+{
+ imx_lluart_map_io();
+ imx_scu_map_io();
+}
+
+static void __init imx6q_gpio_add_irq_domain(struct device_node *np,
+ struct device_node *interrupt_parent)
+{
+ static int gpio_irq_base = MXC_GPIO_IRQ_START + ARCH_NR_GPIOS -
+ 32 * 7; /* imx6q gets 7 gpio ports */
+
+ irq_domain_add_simple(np, gpio_irq_base);
+ gpio_irq_base += 32;
+}
+
+static const struct of_device_id imx6q_irq_match[] __initconst = {
+ { .compatible = "arm,cortex-a9-gic", .data = gic_of_init, },
+ { .compatible = "fsl,imx6q-gpio", .data = imx6q_gpio_add_irq_domain, },
+ { /* sentinel */ }
+};
+
+static void __init imx6q_init_irq(void)
+{
+ l2x0_of_init(0, ~0UL);
+ imx_src_init();
+ imx_gpc_init();
+ of_irq_init(imx6q_irq_match);
+}
+
+static void __init imx6q_timer_init(void)
+{
+ mx6q_clocks_init();
+}
+
+static struct sys_timer imx6q_timer = {
+ .init = imx6q_timer_init,
+};
+
+static const char *imx6q_dt_compat[] __initdata = {
+ "fsl,imx6q-sabreauto",
+ NULL,
+};
+
+DT_MACHINE_START(IMX6Q, "Freescale i.MX6 Quad (Device Tree)")
+ .map_io = imx6q_map_io,
+ .init_irq = imx6q_init_irq,
+ .handle_irq = imx6q_handle_irq,
+ .timer = &imx6q_timer,
+ .init_machine = imx6q_init_machine,
+ .dt_compat = imx6q_dt_compat,
+MACHINE_END
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 2df5504..6dc9967 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -835,7 +835,7 @@ config CACHE_L2X0
REALVIEW_EB_A9MP || SOC_IMX35 || SOC_IMX31 || MACH_REALVIEW_PBX || \
ARCH_NOMADIK || ARCH_OMAP4 || ARCH_EXYNOS4 || ARCH_TEGRA || \
ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || ARCH_SHMOBILE || \
- ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX
+ ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX || ARCH_MX6
default y
select OUTER_CACHE
select OUTER_CACHE_SYNC
diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
index 855c214..571e91d 100644
--- a/arch/arm/plat-mxc/include/mach/common.h
+++ b/arch/arm/plat-mxc/include/mach/common.h
@@ -64,6 +64,7 @@ extern int mx51_clocks_init(unsigned long ckil, unsigned long osc,
unsigned long ckih1, unsigned long ckih2);
extern int mx53_clocks_init(unsigned long ckil, unsigned long osc,
unsigned long ckih1, unsigned long ckih2);
+extern int mx6q_clocks_init(void);
extern struct platform_device *mxc_register_gpio(char *name, int id,
resource_size_t iobase, resource_size_t iosize, int irq, int irq_high);
extern void mxc_set_cpu_type(unsigned int type);
@@ -90,7 +91,19 @@ void gic_handle_irq(struct pt_regs *);
extern void imx_enable_cpu(int cpu, bool enable);
extern void imx_set_cpu_jump(int cpu, void *jump_addr);
+#ifdef CONFIG_DEBUG_LL
+extern void imx_lluart_map_io(void);
+#else
+static inline void imx_lluart_map_io(void) {}
+#endif
#ifdef CONFIG_SMP
extern void v7_secondary_startup(void);
+extern void imx_scu_map_io(void);
+#else
+static inline void imx_scu_map_io(void) {}
#endif
+extern void imx_enable_cpu(int cpu, bool enable);
+extern void imx_set_cpu_jump(int cpu, void *jump_addr);
+extern void imx_src_init(void);
+extern void imx_gpc_init(void);
#endif
--
1.7.4.1
^ permalink raw reply related
* [PATCH v4 7/7] arm/imx6q: add suspend/resume support
From: Shawn Guo @ 2011-09-28 9:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317200808-6275-1-git-send-email-shawn.guo@linaro.org>
It adds suspend/resume support for imx6q.
Signed-off-by: Anson Huang <b20788@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/Makefile | 2 +-
arch/arm/mach-imx/head-v7.S | 32 +++++++++++
arch/arm/mach-imx/pm-imx6q.c | 90 +++++++++++++++++++++++++++++++
arch/arm/plat-mxc/include/mach/common.h | 9 +++
4 files changed, 132 insertions(+), 1 deletions(-)
create mode 100644 arch/arm/mach-imx/pm-imx6q.c
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 31c8602..e6c36b4 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -71,4 +71,4 @@ AFLAGS_head-v7.o :=-Wa,-march=armv7-a
obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
obj-$(CONFIG_LOCAL_TIMERS) += localtimer.o
-obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o
+obj-$(CONFIG_SOC_IMX6Q) += clock-imx6q.o mach-imx6q.o pm-imx6q.o
diff --git a/arch/arm/mach-imx/head-v7.S b/arch/arm/mach-imx/head-v7.S
index ede908b..1f6316c 100644
--- a/arch/arm/mach-imx/head-v7.S
+++ b/arch/arm/mach-imx/head-v7.S
@@ -69,3 +69,35 @@ ENTRY(v7_secondary_startup)
b secondary_startup
ENDPROC(v7_secondary_startup)
#endif
+
+ENTRY(pl310_get_save_ptr)
+ ldr r0, =pl310_pbase
+ mov pc, lr
+ENDPROC(pl310_get_save_ptr)
+
+/*
+ * The following code is located into the .data section. This is to
+ * allow pl310_pbase and pl310_aux_ctrl to be accessed with a relative
+ * load as we are running on physical address here.
+ */
+ .data
+ .align
+
+ .macro pl310_resume
+ adr r2, pl310_pbase
+ ldmia r2, {r0, r1}
+ str r1, [r0, #L2X0_AUX_CTRL] @ restore aux_ctrl
+ mov r1, #0x1
+ str r1, [r0, #L2X0_CTRL] @ re-enable L2
+ .endm
+
+ENTRY(v7_cpu_resume)
+ bl v7_invalidate_l1
+ pl310_resume
+ b cpu_resume
+ENDPROC(v7_cpu_resume)
+
+pl310_pbase:
+ .long 0
+pl310_aux_ctrl:
+ .long 0
diff --git a/arch/arm/mach-imx/pm-imx6q.c b/arch/arm/mach-imx/pm-imx6q.c
new file mode 100644
index 0000000..db41343
--- /dev/null
+++ b/arch/arm/mach-imx/pm-imx6q.c
@@ -0,0 +1,90 @@
+/*
+ * Copyright 2011 Freescale Semiconductor, Inc.
+ * Copyright 2011 Linaro Ltd.
+ *
+ * The code contained herein is licensed under the GNU General Public
+ * License. You may obtain a copy of the GNU General Public License
+ * Version 2 or later at the following locations:
+ *
+ * http://www.opensource.org/licenses/gpl-license.html
+ * http://www.gnu.org/copyleft/gpl.html
+ */
+
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/suspend.h>
+#include <asm/cacheflush.h>
+#include <asm/proc-fns.h>
+#include <asm/suspend.h>
+#include <asm/hardware/cache-l2x0.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
+
+static int imx6q_suspend_finish(unsigned long val)
+{
+ cpu_do_idle();
+ return 0;
+}
+
+static int imx6q_pm_enter(suspend_state_t state)
+{
+ switch (state) {
+ case PM_SUSPEND_MEM:
+ imx6q_set_lpm(STOP_POWER_OFF);
+ imx_gpc_pre_suspend();
+ imx_set_cpu_jump(0, v7_cpu_resume);
+ /* Zzz ... */
+ cpu_suspend(0, imx6q_suspend_finish);
+ imx_smp_prepare();
+ imx_gpc_post_resume();
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ return 0;
+}
+
+static const struct platform_suspend_ops imx6q_pm_ops = {
+ .enter = imx6q_pm_enter,
+ .valid = suspend_valid_only_mem,
+};
+
+void __init imx6q_pm_init(void)
+{
+ struct device_node *np;
+ u32 reg[2], *ptr;
+ void __iomem *base;
+
+ np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
+ of_property_read_u32_array(np, "reg", reg, ARRAY_SIZE(reg));
+ base = ioremap(reg[0], reg[1]);
+ WARN_ON(!base);
+
+ /*
+ * On imx6q, during system suspend, ARM core gets powered off,
+ * but L2 cache is retained. To avoid cleaning the entire L2,
+ * we need to save L2 controller registers, and when system gets
+ * woke up, restore the registers and re-enable L2 before
+ * calling into cpu_resume().
+ *
+ * Most of pl310 configuration upon reset work just fine for
+ * imx6q, and the only one register we actually need to save is
+ * AUX_CTRL. Also since pl310 configuration won't change in a
+ * live system, we can save it here only once, and restore it
+ * every time system resumes back from v7_cpu_resume().
+ */
+ ptr = pl310_get_save_ptr();
+ /* save pl310 physical base address */
+ *ptr = reg[0];
+ /* save pl310 aux_ctrl register */
+ *(ptr + 1) = readl_relaxed(base + L2X0_AUX_CTRL);
+ /* ensure they are written into external memory */
+ __cpuc_flush_dcache_area((void *) ptr, sizeof(*ptr) * 2);
+ outer_clean_range(__pa(ptr), __pa(ptr + 2));
+
+ iounmap(base);
+
+ suspend_set_ops(&imx6q_pm_ops);
+}
diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
index 571e91d..318b995 100644
--- a/arch/arm/plat-mxc/include/mach/common.h
+++ b/arch/arm/plat-mxc/include/mach/common.h
@@ -13,6 +13,7 @@
struct platform_device;
struct clk;
+enum mxc_cpu_pwr_mode;
extern void mx1_map_io(void);
extern void mx21_map_io(void);
@@ -96,14 +97,22 @@ extern void imx_lluart_map_io(void);
#else
static inline void imx_lluart_map_io(void) {}
#endif
+extern void v7_cpu_resume(void);
+extern u32 *pl310_get_save_ptr(void);
#ifdef CONFIG_SMP
extern void v7_secondary_startup(void);
extern void imx_scu_map_io(void);
+extern void imx_smp_prepare(void);
#else
static inline void imx_scu_map_io(void) {}
+static inline void imx_smp_prepare(void) {}
#endif
extern void imx_enable_cpu(int cpu, bool enable);
extern void imx_set_cpu_jump(int cpu, void *jump_addr);
extern void imx_src_init(void);
extern void imx_gpc_init(void);
+extern void imx_gpc_pre_suspend(void);
+extern void imx_gpc_post_resume(void);
+extern int imx6q_set_lpm(enum mxc_cpu_pwr_mode mode);
+extern void imx6q_pm_init(void);
#endif
--
1.7.4.1
^ permalink raw reply related
* [PATCH 0/6] Support single zImage for imx3 and imx6
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
This series supports the single zImage build for imx3 and imx6. It's
based on linux-next with imx6 series applied, and tested on imx35 and
imx6q.
Sascha Hauer (1):
arm/imx: merge i.MX3 and i.MX6
Shawn Guo (5):
arm/imx: merge mm-imx35.c into mm-imx31.c
arm/imx: rename mm-imx31.c to mm-imx3.c
arm/imx: change mxc_init_l2x0() to an imx31/35 specific call
arm/imx: remove cpu_is_xxx() from arch_idle()
arm/imx: remove cpu_is_xxx() check from __imx_ioremap()
arch/arm/Makefile | 3 +-
arch/arm/mach-imx/Kconfig | 7 +-
arch/arm/mach-imx/Makefile | 5 +-
arch/arm/mach-imx/Makefile.boot | 10 +-
arch/arm/mach-imx/cache-l2x0.c | 56 -------
arch/arm/mach-imx/mm-imx3.c | 256 +++++++++++++++++++++++++++++++
arch/arm/mach-imx/mm-imx31.c | 91 -----------
arch/arm/mach-imx/mm-imx35.c | 109 -------------
arch/arm/mach-mx5/mm.c | 6 +
arch/arm/mach-mx5/pm-imx5.c | 3 +-
arch/arm/mm/Kconfig | 4 +-
arch/arm/plat-mxc/Kconfig | 18 +--
arch/arm/plat-mxc/include/mach/common.h | 2 +
arch/arm/plat-mxc/include/mach/io.h | 22 +--
arch/arm/plat-mxc/include/mach/system.h | 35 +----
arch/arm/plat-mxc/system.c | 3 +
16 files changed, 300 insertions(+), 330 deletions(-)
^ permalink raw reply
* [PATCH 1/6] arm/imx: merge mm-imx35.c into mm-imx31.c
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201368-6403-1-git-send-email-shawn.guo@linaro.org>
As imx31 and imx35 have much in common at soc level, this patch merges
mm-imx35.c into mm-imx31.c, so that the common functions between imx31
and imx35 can be added in one file later.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/Makefile | 2 +-
arch/arm/mach-imx/mm-imx31.c | 78 ++++++++++++++++++++++++++++++
arch/arm/mach-imx/mm-imx35.c | 109 ------------------------------------------
3 files changed, 79 insertions(+), 110 deletions(-)
delete mode 100644 arch/arm/mach-imx/mm-imx35.c
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index e6c36b4..940f130 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -9,7 +9,7 @@ obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o
obj-$(CONFIG_SOC_IMX27) += clock-imx27.o mm-imx27.o ehci-imx27.o
obj-$(CONFIG_SOC_IMX31) += mm-imx31.o cpu-imx31.o clock-imx31.o iomux-imx31.o ehci-imx31.o
-obj-$(CONFIG_SOC_IMX35) += mm-imx35.o cpu-imx35.o clock-imx35.o ehci-imx35.o
+obj-$(CONFIG_SOC_IMX35) += mm-imx31.o cpu-imx35.o clock-imx35.o ehci-imx35.o
obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
# Support for CMOS sensor interface
diff --git a/arch/arm/mach-imx/mm-imx31.c b/arch/arm/mach-imx/mm-imx31.c
index b7c55e7..e06eed1 100644
--- a/arch/arm/mach-imx/mm-imx31.c
+++ b/arch/arm/mach-imx/mm-imx31.c
@@ -47,17 +47,42 @@ void __init mx31_map_io(void)
iotable_init(mx31_io_desc, ARRAY_SIZE(mx31_io_desc));
}
+static struct map_desc mx35_io_desc[] __initdata = {
+ imx_map_entry(MX35, X_MEMC, MT_DEVICE),
+ imx_map_entry(MX35, AVIC, MT_DEVICE_NONSHARED),
+ imx_map_entry(MX35, AIPS1, MT_DEVICE_NONSHARED),
+ imx_map_entry(MX35, AIPS2, MT_DEVICE_NONSHARED),
+ imx_map_entry(MX35, SPBA0, MT_DEVICE_NONSHARED),
+};
+
+void __init mx35_map_io(void)
+{
+ iotable_init(mx35_io_desc, ARRAY_SIZE(mx35_io_desc));
+}
+
void __init imx31_init_early(void)
{
mxc_set_cpu_type(MXC_CPU_MX31);
mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
}
+void __init imx35_init_early(void)
+{
+ mxc_set_cpu_type(MXC_CPU_MX35);
+ mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
+ mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
+}
+
void __init mx31_init_irq(void)
{
mxc_init_irq(MX31_IO_ADDRESS(MX31_AVIC_BASE_ADDR));
}
+void __init mx35_init_irq(void)
+{
+ mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR));
+}
+
static struct sdma_script_start_addrs imx31_to1_sdma_script __initdata = {
.per_2_per_addr = 1677,
};
@@ -89,3 +114,56 @@ void __init imx31_soc_init(void)
imx_add_imx_sdma("imx31-sdma", MX31_SDMA_BASE_ADDR, MX31_INT_SDMA, &imx31_sdma_pdata);
}
+
+static struct sdma_script_start_addrs imx35_to1_sdma_script __initdata = {
+ .ap_2_ap_addr = 642,
+ .uart_2_mcu_addr = 817,
+ .mcu_2_app_addr = 747,
+ .uartsh_2_mcu_addr = 1183,
+ .per_2_shp_addr = 1033,
+ .mcu_2_shp_addr = 961,
+ .ata_2_mcu_addr = 1333,
+ .mcu_2_ata_addr = 1252,
+ .app_2_mcu_addr = 683,
+ .shp_2_per_addr = 1111,
+ .shp_2_mcu_addr = 892,
+};
+
+static struct sdma_script_start_addrs imx35_to2_sdma_script __initdata = {
+ .ap_2_ap_addr = 729,
+ .uart_2_mcu_addr = 904,
+ .per_2_app_addr = 1597,
+ .mcu_2_app_addr = 834,
+ .uartsh_2_mcu_addr = 1270,
+ .per_2_shp_addr = 1120,
+ .mcu_2_shp_addr = 1048,
+ .ata_2_mcu_addr = 1429,
+ .mcu_2_ata_addr = 1339,
+ .app_2_per_addr = 1531,
+ .app_2_mcu_addr = 770,
+ .shp_2_per_addr = 1198,
+ .shp_2_mcu_addr = 979,
+};
+
+static struct sdma_platform_data imx35_sdma_pdata __initdata = {
+ .fw_name = "sdma-imx35-to2.bin",
+ .script_addrs = &imx35_to2_sdma_script,
+};
+
+void __init imx35_soc_init(void)
+{
+ int to_version = mx35_revision() >> 4;
+
+ /* i.mx35 has the i.mx31 type gpio */
+ mxc_register_gpio("imx31-gpio", 0, MX35_GPIO1_BASE_ADDR, SZ_16K, MX35_INT_GPIO1, 0);
+ mxc_register_gpio("imx31-gpio", 1, MX35_GPIO2_BASE_ADDR, SZ_16K, MX35_INT_GPIO2, 0);
+ mxc_register_gpio("imx31-gpio", 2, MX35_GPIO3_BASE_ADDR, SZ_16K, MX35_INT_GPIO3, 0);
+
+ if (to_version == 1) {
+ strncpy(imx35_sdma_pdata.fw_name, "sdma-imx35-to1.bin",
+ strlen(imx35_sdma_pdata.fw_name));
+ imx35_sdma_pdata.script_addrs = &imx35_to1_sdma_script;
+ }
+
+ imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata);
+}
diff --git a/arch/arm/mach-imx/mm-imx35.c b/arch/arm/mach-imx/mm-imx35.c
deleted file mode 100644
index f49bac7..0000000
--- a/arch/arm/mach-imx/mm-imx35.c
+++ /dev/null
@@ -1,109 +0,0 @@
-/*
- * Copyright (C) 1999,2000 Arm Limited
- * Copyright (C) 2000 Deep Blue Solutions Ltd
- * Copyright (C) 2002 Shane Nay (shane at minirl.com)
- * Copyright 2005-2007 Freescale Semiconductor, Inc. All Rights Reserved.
- * - add MX31 specific definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License as published by
- * the Free Software Foundation; either version 2 of the License, or
- * (at your option) any later version.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
- */
-
-#include <linux/mm.h>
-#include <linux/init.h>
-#include <linux/err.h>
-
-#include <asm/pgtable.h>
-#include <asm/mach/map.h>
-#include <asm/hardware/cache-l2x0.h>
-
-#include <mach/common.h>
-#include <mach/devices-common.h>
-#include <mach/hardware.h>
-#include <mach/iomux-v3.h>
-#include <mach/irqs.h>
-
-static struct map_desc mx35_io_desc[] __initdata = {
- imx_map_entry(MX35, X_MEMC, MT_DEVICE),
- imx_map_entry(MX35, AVIC, MT_DEVICE_NONSHARED),
- imx_map_entry(MX35, AIPS1, MT_DEVICE_NONSHARED),
- imx_map_entry(MX35, AIPS2, MT_DEVICE_NONSHARED),
- imx_map_entry(MX35, SPBA0, MT_DEVICE_NONSHARED),
-};
-
-void __init mx35_map_io(void)
-{
- iotable_init(mx35_io_desc, ARRAY_SIZE(mx35_io_desc));
-}
-
-void __init imx35_init_early(void)
-{
- mxc_set_cpu_type(MXC_CPU_MX35);
- mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
- mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
-}
-
-void __init mx35_init_irq(void)
-{
- mxc_init_irq(MX35_IO_ADDRESS(MX35_AVIC_BASE_ADDR));
-}
-
-static struct sdma_script_start_addrs imx35_to1_sdma_script __initdata = {
- .ap_2_ap_addr = 642,
- .uart_2_mcu_addr = 817,
- .mcu_2_app_addr = 747,
- .uartsh_2_mcu_addr = 1183,
- .per_2_shp_addr = 1033,
- .mcu_2_shp_addr = 961,
- .ata_2_mcu_addr = 1333,
- .mcu_2_ata_addr = 1252,
- .app_2_mcu_addr = 683,
- .shp_2_per_addr = 1111,
- .shp_2_mcu_addr = 892,
-};
-
-static struct sdma_script_start_addrs imx35_to2_sdma_script __initdata = {
- .ap_2_ap_addr = 729,
- .uart_2_mcu_addr = 904,
- .per_2_app_addr = 1597,
- .mcu_2_app_addr = 834,
- .uartsh_2_mcu_addr = 1270,
- .per_2_shp_addr = 1120,
- .mcu_2_shp_addr = 1048,
- .ata_2_mcu_addr = 1429,
- .mcu_2_ata_addr = 1339,
- .app_2_per_addr = 1531,
- .app_2_mcu_addr = 770,
- .shp_2_per_addr = 1198,
- .shp_2_mcu_addr = 979,
-};
-
-static struct sdma_platform_data imx35_sdma_pdata __initdata = {
- .fw_name = "sdma-imx35-to2.bin",
- .script_addrs = &imx35_to2_sdma_script,
-};
-
-void __init imx35_soc_init(void)
-{
- int to_version = mx35_revision() >> 4;
-
- /* i.mx35 has the i.mx31 type gpio */
- mxc_register_gpio("imx31-gpio", 0, MX35_GPIO1_BASE_ADDR, SZ_16K, MX35_INT_GPIO1, 0);
- mxc_register_gpio("imx31-gpio", 1, MX35_GPIO2_BASE_ADDR, SZ_16K, MX35_INT_GPIO2, 0);
- mxc_register_gpio("imx31-gpio", 2, MX35_GPIO3_BASE_ADDR, SZ_16K, MX35_INT_GPIO3, 0);
-
- if (to_version == 1) {
- strncpy(imx35_sdma_pdata.fw_name, "sdma-imx35-to1.bin",
- strlen(imx35_sdma_pdata.fw_name));
- imx35_sdma_pdata.script_addrs = &imx35_to1_sdma_script;
- }
-
- imx_add_imx_sdma("imx35-sdma", MX35_SDMA_BASE_ADDR, MX35_INT_SDMA, &imx35_sdma_pdata);
-}
--
1.7.4.1
^ permalink raw reply related
* [PATCH 2/6] arm/imx: rename mm-imx31.c to mm-imx3.c
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201368-6403-1-git-send-email-shawn.guo@linaro.org>
Since mm-imx31.c now is shared between imx31 and imx35, the patch
renames mm-imx31.c to mm-imx3.c.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/Makefile | 4 ++--
arch/arm/mach-imx/{mm-imx31.c => mm-imx3.c} | 0
2 files changed, 2 insertions(+), 2 deletions(-)
rename arch/arm/mach-imx/{mm-imx31.c => mm-imx3.c} (100%)
diff --git a/arch/arm/mach-imx/Makefile b/arch/arm/mach-imx/Makefile
index 940f130..fb5dfd5 100644
--- a/arch/arm/mach-imx/Makefile
+++ b/arch/arm/mach-imx/Makefile
@@ -8,8 +8,8 @@ obj-$(CONFIG_SOC_IMX25) += clock-imx25.o mm-imx25.o ehci-imx25.o cpu-imx25.o
obj-$(CONFIG_SOC_IMX27) += cpu-imx27.o pm-imx27.o
obj-$(CONFIG_SOC_IMX27) += clock-imx27.o mm-imx27.o ehci-imx27.o
-obj-$(CONFIG_SOC_IMX31) += mm-imx31.o cpu-imx31.o clock-imx31.o iomux-imx31.o ehci-imx31.o
-obj-$(CONFIG_SOC_IMX35) += mm-imx31.o cpu-imx35.o clock-imx35.o ehci-imx35.o
+obj-$(CONFIG_SOC_IMX31) += mm-imx3.o cpu-imx31.o clock-imx31.o iomux-imx31.o ehci-imx31.o
+obj-$(CONFIG_SOC_IMX35) += mm-imx3.o cpu-imx35.o clock-imx35.o ehci-imx35.o
obj-$(CONFIG_CACHE_L2X0) += cache-l2x0.o
# Support for CMOS sensor interface
diff --git a/arch/arm/mach-imx/mm-imx31.c b/arch/arm/mach-imx/mm-imx3.c
similarity index 100%
rename from arch/arm/mach-imx/mm-imx31.c
rename to arch/arm/mach-imx/mm-imx3.c
--
1.7.4.1
^ permalink raw reply related
* [PATCH 3/6] arm/imx: change mxc_init_l2x0() to an imx31/35 specific call
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201368-6403-1-git-send-email-shawn.guo@linaro.org>
The mxc_init_l2x0() should really be an imx31/35 specific call.
The patch removes early_initcall from mxc_init_l2x0() and get imx31
and imx35 soc specific function calls mxc_init_l2x0(), so that it's
not necessarily to be called for all imx socs when we build single
image for multiple imx socs.
Thus the function can be renamed to imx3_init_l2x0() and put into
mm-imx3.c. It also changes the return type from integer to void.
^ permalink raw reply
* [PATCH 4/6] arm/imx: remove cpu_is_xxx() from arch_idle()
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201368-6403-1-git-send-email-shawn.guo@linaro.org>
This patch adds an idle hook imx_idle to be called in arch_idle().
Any soc that needs a customized idle implementation other than
cpu_do_idle() can set up this hook in soc specific call.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/mm-imx3.c | 30 ++++++++++++++++++++++++++
arch/arm/mach-mx5/mm.c | 6 +++++
arch/arm/mach-mx5/pm-imx5.c | 3 +-
arch/arm/plat-mxc/include/mach/common.h | 2 +
arch/arm/plat-mxc/include/mach/system.h | 35 ++----------------------------
arch/arm/plat-mxc/system.c | 2 +
6 files changed, 45 insertions(+), 33 deletions(-)
diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c
index ffa33b4..6fad0d6 100644
--- a/arch/arm/mach-imx/mm-imx3.c
+++ b/arch/arm/mach-imx/mm-imx3.c
@@ -30,6 +30,34 @@
#include <mach/iomux-v3.h>
#include <mach/irqs.h>
+static void imx3_idle(void)
+{
+ unsigned long reg = 0;
+ __asm__ __volatile__(
+ /* disable I and D cache */
+ "mrc p15, 0, %0, c1, c0, 0\n"
+ "bic %0, %0, #0x00001000\n"
+ "bic %0, %0, #0x00000004\n"
+ "mcr p15, 0, %0, c1, c0, 0\n"
+ /* invalidate I cache */
+ "mov %0, #0\n"
+ "mcr p15, 0, %0, c7, c5, 0\n"
+ /* clear and invalidate D cache */
+ "mov %0, #0\n"
+ "mcr p15, 0, %0, c7, c14, 0\n"
+ /* WFI */
+ "mov %0, #0\n"
+ "mcr p15, 0, %0, c7, c0, 4\n"
+ "nop\n" "nop\n" "nop\n" "nop\n"
+ "nop\n" "nop\n" "nop\n"
+ /* enable I and D cache */
+ "mrc p15, 0, %0, c1, c0, 0\n"
+ "orr %0, %0, #0x00001000\n"
+ "orr %0, %0, #0x00000004\n"
+ "mcr p15, 0, %0, c1, c0, 0\n"
+ : "=r" (reg));
+}
+
void imx3_init_l2x0(void)
{
void __iomem *l2x0_base;
@@ -98,6 +126,7 @@ void __init imx31_init_early(void)
{
mxc_set_cpu_type(MXC_CPU_MX31);
mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
+ imx_idle = imx3_idle;
}
void __init imx35_init_early(void)
@@ -105,6 +134,7 @@ void __init imx35_init_early(void)
mxc_set_cpu_type(MXC_CPU_MX35);
mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
+ imx_idle = imx3_idle;
}
void __init mx31_init_irq(void)
diff --git a/arch/arm/mach-mx5/mm.c b/arch/arm/mach-mx5/mm.c
index fb65339..26eacc9 100644
--- a/arch/arm/mach-mx5/mm.c
+++ b/arch/arm/mach-mx5/mm.c
@@ -21,6 +21,11 @@
#include <mach/devices-common.h>
#include <mach/iomux-v3.h>
+static void imx5_idle(void)
+{
+ mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
+}
+
/*
* Define the MX50 memory map.
*/
@@ -84,6 +89,7 @@ void __init imx51_init_early(void)
mxc_set_cpu_type(MXC_CPU_MX51);
mxc_iomux_v3_init(MX51_IO_ADDRESS(MX51_IOMUXC_BASE_ADDR));
mxc_arch_reset_init(MX51_IO_ADDRESS(MX51_WDOG1_BASE_ADDR));
+ imx_idle = imx5_idle;
}
void __init imx53_init_early(void)
diff --git a/arch/arm/mach-mx5/pm-imx5.c b/arch/arm/mach-mx5/pm-imx5.c
index be19e9c..98052fc 100644
--- a/arch/arm/mach-mx5/pm-imx5.c
+++ b/arch/arm/mach-mx5/pm-imx5.c
@@ -14,7 +14,8 @@
#include <linux/err.h>
#include <asm/cacheflush.h>
#include <asm/tlbflush.h>
-#include <mach/system.h>
+#include <mach/common.h>
+#include <mach/hardware.h>
#include "crm_regs.h"
static struct clk *gpc_dvfs_clk;
diff --git a/arch/arm/plat-mxc/include/mach/common.h b/arch/arm/plat-mxc/include/mach/common.h
index 318b995..245fb98 100644
--- a/arch/arm/plat-mxc/include/mach/common.h
+++ b/arch/arm/plat-mxc/include/mach/common.h
@@ -73,7 +73,9 @@ extern void mxc_arch_reset_init(void __iomem *);
extern void mx51_efikamx_reset(void);
extern int mx53_revision(void);
extern int mx53_display_revision(void);
+extern void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode);
extern void imx_print_silicon_rev(const char *cpu, int srev);
+extern void (*imx_idle)(void);
void avic_handle_irq(struct pt_regs *);
void tzic_handle_irq(struct pt_regs *);
diff --git a/arch/arm/plat-mxc/include/mach/system.h b/arch/arm/plat-mxc/include/mach/system.h
index 51f02a9..cf88b35 100644
--- a/arch/arm/plat-mxc/include/mach/system.h
+++ b/arch/arm/plat-mxc/include/mach/system.h
@@ -17,41 +17,12 @@
#ifndef __ASM_ARCH_MXC_SYSTEM_H__
#define __ASM_ARCH_MXC_SYSTEM_H__
-#include <mach/hardware.h>
-#include <mach/common.h>
-
-extern void mx5_cpu_lp_set(enum mxc_cpu_pwr_mode mode);
+extern void (*imx_idle)(void);
static inline void arch_idle(void)
{
- /* fix i.MX31 errata TLSbo65953 and i.MX35 errata ENGcm09472 */
- if (cpu_is_mx31() || cpu_is_mx35()) {
- unsigned long reg = 0;
- __asm__ __volatile__(
- /* disable I and D cache */
- "mrc p15, 0, %0, c1, c0, 0\n"
- "bic %0, %0, #0x00001000\n"
- "bic %0, %0, #0x00000004\n"
- "mcr p15, 0, %0, c1, c0, 0\n"
- /* invalidate I cache */
- "mov %0, #0\n"
- "mcr p15, 0, %0, c7, c5, 0\n"
- /* clear and invalidate D cache */
- "mov %0, #0\n"
- "mcr p15, 0, %0, c7, c14, 0\n"
- /* WFI */
- "mov %0, #0\n"
- "mcr p15, 0, %0, c7, c0, 4\n"
- "nop\n" "nop\n" "nop\n" "nop\n"
- "nop\n" "nop\n" "nop\n"
- /* enable I and D cache */
- "mrc p15, 0, %0, c1, c0, 0\n"
- "orr %0, %0, #0x00001000\n"
- "orr %0, %0, #0x00000004\n"
- "mcr p15, 0, %0, c1, c0, 0\n"
- : "=r" (reg));
- } else if (cpu_is_mx51())
- mx5_cpu_lp_set(WAIT_UNCLOCKED_POWER_OFF);
+ if (imx_idle != NULL)
+ (imx_idle)();
else
cpu_do_idle();
}
diff --git a/arch/arm/plat-mxc/system.c b/arch/arm/plat-mxc/system.c
index 8024f2a..5fa03e7 100644
--- a/arch/arm/plat-mxc/system.c
+++ b/arch/arm/plat-mxc/system.c
@@ -28,6 +28,8 @@
#include <asm/system.h>
#include <asm/mach-types.h>
+void (*imx_idle)(void) = NULL;
+
static void __iomem *wdog_base;
/*
--
1.7.4.1
^ permalink raw reply related
* [PATCH 5/6] arm/imx: remove cpu_is_xxx() check from __imx_ioremap()
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201368-6403-1-git-send-email-shawn.guo@linaro.org>
This patch adds an ioremap hook imx_ioremap to be called in
__imx_ioremap(). Any soc that needs a customized ioremap other
than __arm_ioremap() can set up this hook in soc specific call.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/mach-imx/mm-imx3.c | 19 +++++++++++++++++++
arch/arm/plat-mxc/include/mach/io.h | 22 ++++++----------------
arch/arm/plat-mxc/system.c | 1 +
3 files changed, 26 insertions(+), 16 deletions(-)
diff --git a/arch/arm/mach-imx/mm-imx3.c b/arch/arm/mach-imx/mm-imx3.c
index 6fad0d6..9f0e82e 100644
--- a/arch/arm/mach-imx/mm-imx3.c
+++ b/arch/arm/mach-imx/mm-imx3.c
@@ -58,6 +58,23 @@ static void imx3_idle(void)
: "=r" (reg));
}
+static void __iomem *imx3_ioremap(unsigned long phys_addr, size_t size,
+ unsigned int mtype)
+{
+ if (mtype == MT_DEVICE) {
+ /*
+ * Access all peripherals below 0x80000000 as nonshared device
+ * on mx3, but leave l2cc alone. Otherwise cache corruptions
+ * can occur.
+ */
+ if (phys_addr < 0x80000000 &&
+ !addr_in_module(phys_addr, MX3x_L2CC))
+ mtype = MT_DEVICE_NONSHARED;
+ }
+
+ return __arm_ioremap(phys_addr, size, mtype);
+}
+
void imx3_init_l2x0(void)
{
void __iomem *l2x0_base;
@@ -127,6 +144,7 @@ void __init imx31_init_early(void)
mxc_set_cpu_type(MXC_CPU_MX31);
mxc_arch_reset_init(MX31_IO_ADDRESS(MX31_WDOG_BASE_ADDR));
imx_idle = imx3_idle;
+ imx_ioremap = imx3_ioremap;
}
void __init imx35_init_early(void)
@@ -135,6 +153,7 @@ void __init imx35_init_early(void)
mxc_iomux_v3_init(MX35_IO_ADDRESS(MX35_IOMUXC_BASE_ADDR));
mxc_arch_reset_init(MX35_IO_ADDRESS(MX35_WDOG_BASE_ADDR));
imx_idle = imx3_idle;
+ imx_ioremap = imx3_ioremap;
}
void __init mx31_init_irq(void)
diff --git a/arch/arm/plat-mxc/include/mach/io.h b/arch/arm/plat-mxc/include/mach/io.h
index 4347a87..338300b 100644
--- a/arch/arm/plat-mxc/include/mach/io.h
+++ b/arch/arm/plat-mxc/include/mach/io.h
@@ -14,32 +14,22 @@
/* Allow IO space to be anywhere in the memory */
#define IO_SPACE_LIMIT 0xffffffff
-#if defined(CONFIG_SOC_IMX31) || defined(CONFIG_SOC_IMX35)
-#include <mach/hardware.h>
-
#define __arch_ioremap __imx_ioremap
#define __arch_iounmap __iounmap
#define addr_in_module(addr, mod) \
((unsigned long)(addr) - mod ## _BASE_ADDR < mod ## _SIZE)
+extern void __iomem *(*imx_ioremap)(unsigned long, size_t, unsigned int);
+
static inline void __iomem *
__imx_ioremap(unsigned long phys_addr, size_t size, unsigned int mtype)
{
- if (mtype == MT_DEVICE && (cpu_is_mx31() || cpu_is_mx35())) {
- /*
- * Access all peripherals below 0x80000000 as nonshared device
- * on mx3, but leave l2cc alone. Otherwise cache corruptions
- * can occur.
- */
- if (phys_addr < 0x80000000 &&
- !addr_in_module(phys_addr, MX3x_L2CC))
- mtype = MT_DEVICE_NONSHARED;
- }
-
- return __arm_ioremap(phys_addr, size, mtype);
+ if (imx_ioremap != NULL)
+ return imx_ioremap(phys_addr, size, mtype);
+ else
+ return __arm_ioremap(phys_addr, size, mtype);
}
-#endif
/* io address mapping macro */
#define __io(a) __typesafe_io(a)
diff --git a/arch/arm/plat-mxc/system.c b/arch/arm/plat-mxc/system.c
index 5fa03e7..9dad8dc 100644
--- a/arch/arm/plat-mxc/system.c
+++ b/arch/arm/plat-mxc/system.c
@@ -29,6 +29,7 @@
#include <asm/mach-types.h>
void (*imx_idle)(void) = NULL;
+void __iomem *(*imx_ioremap)(unsigned long, size_t, unsigned int) = NULL;
static void __iomem *wdog_base;
--
1.7.4.1
^ permalink raw reply related
* [PATCH 6/6] arm/imx: merge i.MX3 and i.MX6
From: Shawn Guo @ 2011-09-28 9:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201368-6403-1-git-send-email-shawn.guo@linaro.org>
From: Sascha Hauer <s.hauer@pengutronix.de>
The patch merges the build of imx3 and imx6. The Kconfig symbol
ARCH_IMX_V6_V7 is introduced to replace ARCH_MX3 and ARCH_MX6.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
---
arch/arm/Makefile | 3 +--
arch/arm/mach-imx/Kconfig | 7 +++----
arch/arm/mach-imx/Makefile.boot | 10 +++++++---
arch/arm/mm/Kconfig | 4 ++--
arch/arm/plat-mxc/Kconfig | 18 +++++++-----------
5 files changed, 20 insertions(+), 22 deletions(-)
diff --git a/arch/arm/Makefile b/arch/arm/Makefile
index fc36c1b..28e4619 100644
--- a/arch/arm/Makefile
+++ b/arch/arm/Makefile
@@ -158,9 +158,8 @@ machine-$(CONFIG_ARCH_MMP) := mmp
machine-$(CONFIG_ARCH_MSM) := msm
machine-$(CONFIG_ARCH_MV78XX0) := mv78xx0
machine-$(CONFIG_ARCH_IMX_V4_V5) := imx
-machine-$(CONFIG_ARCH_MX3) := imx
+machine-$(CONFIG_ARCH_IMX_V6_V7) := imx
machine-$(CONFIG_ARCH_MX5) := mx5
-machine-$(CONFIG_ARCH_MX6) := imx
machine-$(CONFIG_ARCH_MXS) := mxs
machine-$(CONFIG_ARCH_NETX) := netx
machine-$(CONFIG_ARCH_NOMADIK) := nomadik
diff --git a/arch/arm/mach-imx/Kconfig b/arch/arm/mach-imx/Kconfig
index d52fe3d..fe5cd06 100644
--- a/arch/arm/mach-imx/Kconfig
+++ b/arch/arm/mach-imx/Kconfig
@@ -74,6 +74,7 @@ config SOC_IMX31
select ARCH_MXC_AUDMUX_V2
select ARCH_MX31
select MXC_AVIC
+ select SMP_ON_UP if SMP
config SOC_IMX35
bool
@@ -83,6 +84,7 @@ config SOC_IMX35
select HAVE_EPIT
select ARCH_MX35
select MXC_AVIC
+ select SMP_ON_UP if SMP
if ARCH_IMX_V4_V5
@@ -351,7 +353,7 @@ config MACH_IMX27IPCAM
endif
-if ARCH_MX3
+if ARCH_IMX_V6_V7
comment "MX31 platforms:"
@@ -601,9 +603,6 @@ config MACH_VPR200
Include support for VPR200 platform. This includes specific
configurations for the board and its peripherals.
-endif
-
-if ARCH_MX6
comment "i.MX6 family:"
config SOC_IMX6Q
diff --git a/arch/arm/mach-imx/Makefile.boot b/arch/arm/mach-imx/Makefile.boot
index 22d8588..c349a96 100644
--- a/arch/arm/mach-imx/Makefile.boot
+++ b/arch/arm/mach-imx/Makefile.boot
@@ -14,9 +14,13 @@ zreladdr-$(CONFIG_MACH_MX27) += 0xA0008000
params_phys-$(CONFIG_MACH_MX27) := 0xA0000100
initrd_phys-$(CONFIG_MACH_MX27) := 0xA0800000
-zreladdr-$(CONFIG_ARCH_MX3) += 0x80008000
-params_phys-$(CONFIG_ARCH_MX3) := 0x80000100
-initrd_phys-$(CONFIG_ARCH_MX3) := 0x80800000
+zreladdr-$(CONFIG_SOC_IMX31) += 0x80008000
+params_phys-$(CONFIG_SOC_IMX31) := 0x80000100
+initrd_phys-$(CONFIG_SOC_IMX31) := 0x80800000
+
+zreladdr-$(CONFIG_SOC_IMX35) += 0x80008000
+params_phys-$(CONFIG_SOC_IMX35) := 0x80000100
+initrd_phys-$(CONFIG_SOC_IMX35) := 0x80800000
zreladdr-$(CONFIG_SOC_IMX6Q) += 0x10008000
params_phys-$(CONFIG_SOC_IMX6Q) := 0x10000100
diff --git a/arch/arm/mm/Kconfig b/arch/arm/mm/Kconfig
index 6dc9967..bc68200 100644
--- a/arch/arm/mm/Kconfig
+++ b/arch/arm/mm/Kconfig
@@ -832,10 +832,10 @@ config CACHE_FEROCEON_L2_WRITETHROUGH
config CACHE_L2X0
bool "Enable the L2x0 outer cache controller"
depends on REALVIEW_EB_ARM11MP || MACH_REALVIEW_PB11MP || MACH_REALVIEW_PB1176 || \
- REALVIEW_EB_A9MP || SOC_IMX35 || SOC_IMX31 || MACH_REALVIEW_PBX || \
+ REALVIEW_EB_A9MP || ARCH_IMX_V6_V7 || MACH_REALVIEW_PBX || \
ARCH_NOMADIK || ARCH_OMAP4 || ARCH_EXYNOS4 || ARCH_TEGRA || \
ARCH_U8500 || ARCH_VEXPRESS_CA9X4 || ARCH_SHMOBILE || \
- ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX || ARCH_MX6
+ ARCH_PRIMA2 || ARCH_ZYNQ || ARCH_CNS3XXX
default y
select OUTER_CACHE
select OUTER_CACHE_SYNC
diff --git a/arch/arm/plat-mxc/Kconfig b/arch/arm/plat-mxc/Kconfig
index e2e3e5a..8bbc9c6 100644
--- a/arch/arm/plat-mxc/Kconfig
+++ b/arch/arm/plat-mxc/Kconfig
@@ -6,7 +6,7 @@ menu "Freescale MXC Implementations"
choice
prompt "Freescale CPU family:"
- default ARCH_MX3
+ default ARCH_IMX_V6_V7
config ARCH_IMX_V4_V5
bool "i.MX1, i.MX21, i.MX25, i.MX27"
@@ -16,10 +16,13 @@ config ARCH_IMX_V4_V5
This enables support for systems based on the Freescale i.MX ARMv4
and ARMv5 SoCs
-config ARCH_MX3
- bool "MX3-based"
+config ARCH_IMX_V6_V7
+ bool "i.MX3, i.MX6"
+ select AUTO_ZRELADDR
+ select ARM_PATCH_PHYS_VIRT
help
- This enables support for systems based on the Freescale i.MX3 family
+ This enables support for systems based on the Freescale i.MX3 and i.MX6
+ family.
config ARCH_MX5
bool "i.MX50, i.MX51, i.MX53"
@@ -29,13 +32,6 @@ config ARCH_MX5
This enables support for machines using Freescale's i.MX50 and i.MX51
processors.
-config ARCH_MX6
- bool "i.MX6"
- select AUTO_ZRELADDR
- select ARM_PATCH_PHYS_VIRT
- help
- This enables support for systems based on the Freescale i.MX6 family
-
endchoice
source "arch/arm/mach-imx/Kconfig"
--
1.7.4.1
^ permalink raw reply related
* [PATCH 3/3] mmc: mmci: Change vdd_handler to a generic ios_handler
From: Sebastian RASMUSSEN @ 2011-09-28 9:18 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CACRpkdZpbs06Gi27dpVearp1zV6Xi-8-88E1GJmRca3u_N1zbg@mail.gmail.com>
> I'm guessing it was some feature intended to control e.g. a
> regulator of some kind by routing them off-chip (since mixed-signal
> chips rarely have MMC controllers inside...) and most designers
> already have their own regulator designs so it made no sense
> for anyone to actually implement it that way.
Yup, I think ARM PL180 HW IP developers envisioned that the SD-card
regulator and/or level-shifter would utilize these signals electrically
to configure what voltage to use. As far as I read the old TRM the way
these bits encoded voltage levels were application-specific so I can't
see that there would be any consensus of how to interpret them either.
> If some vendor would actually start using these bits for the
> intended purpose I guess we could adapt. (The pirate driver
> msm_sdcc.c does not seem to use these bits either BTW.)
I never did check whether msm_sdcc used those, but it seemed
unimportant at the time since it's not the same driver (yet).
Nice to know that neither driver uses those though.
/ Sebastian
^ permalink raw reply
* [PATCH 1/2] drivers: create a pin control subsystem v7
From: Linus Walleij @ 2011-09-28 9:18 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAOY=C6ESgRpdCYb8tCxmmdRGfjv+gqroDNiq63zyRjardVicjQ@mail.gmail.com>
On Tue, Sep 27, 2011 at 11:30 AM, Stijn Devriendt <highguy@gmail.com> wrote:
>> + ? ? ? spin_unlock(&desc->lock);
>
> Now this is racing with...
> (...)
> ... this:
>
>> + ? ? ? spin_lock(&desc->lock);
>> + ? ? ? desc->mux_requested = true;
>> + ? ? ? strncpy(desc->mux_function, function, sizeof(desc->mux_function));
>> + ? ? ? spin_unlock(&desc->lock);
Good catch!
I've fixed it by setting ->mux_requested immediatelty and then
later release it (inside a lock) if something fails.
Yours,
Linus Walleij
^ permalink raw reply
* [PATCH v5 0/6] Add device tree support for PL330 dma controller driver
From: Thomas Abraham @ 2011-09-28 9:25 UTC (permalink / raw)
To: linux-arm-kernel
Changes since v4:
- Rebased with Samsung maintainer's for-next branch which is at linux-3.1-rc7
- Modified Patch 6/6 to apply cleanly.
Changes since v3:
- In Patch 4/6, a recommendation is added in the pl330 binding documentation
for the name of the property which specifies the dma channel in the client
device node.
- In Patch 6/6, dropped #ifdef around of_have_populated_dt.
Changes since v2:
- Only the sixth patch is changed, to make dma platform data conditionally
selectable.
- Tested with v8 version of pl330 dma driver update patches from Boojin Kim.
Changes since v1:
- Removed "arm,pl330-pdma" and "arm,pl330-mdma" compatible values.
- Removed "arm,primecell-periphid" and "arm,pl330-peri-reqs"
property requirements.
This patchset adds device tree support for PL330 driver and uses it
to add device tree support for Samsung platforms, specifically Exynos4.
First patch moves the pl330_filter function from Samsung specific wrappers
to pl330 dma driver and also adds a check to ensure that the filter
function proceeds only if it the dma channel being investigated belongs
to pl330 dma controller instance.
Second patch adds support to infer the direction of the dma transfer
using the direction specified with the transfer request instead of
including this information in the platform data. This simlifies the
addition of device tree support. Third patch simplifies the platform
data for Exynos4 pl330 dma controllers. Similar patches simplifying
the platform data for other Samsung platforms is under development.
Fourth patch adds device tree support for pl330 dma controller driver.
A dma channel is represented using a phandle of the dma controller
node and the channel id within that controller. Client driver request
a dma channel using the phandle and channel id pair. Correspondingly,
the pl330 filter function has been modified to lookup a channel based
on this value.
Fifth patch adds device tree support for Samsung's DMA engine wrappers.
Client drivers retrive the channel property from their device node and
pass it to the wrappers. The wrapper functions use the property value
as the filter function parameter. Sixth patch restricts the usage of
pl330 device and platform data instances to non-dt platforms.
This patchset is based on Linux 3.1-rc7 and tested tested for both
device-tree and non-device-tree kernel on smdkv310.
Thomas Abraham (6):
DMA: PL330: move filter function into driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
ARM: EXYNOS4: Modify platform data for pl330 driver
DMA: PL330: Add device tree support
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
ARM: EXYNOS4: Limit usage of pl330 device instance to non-dt build
^ permalink raw reply
* [PATCH v5 1/6] DMA: PL330: move filter function into driver
From: Thomas Abraham @ 2011-09-28 9:25 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1317201925-25148-1-git-send-email-thomas.abraham@linaro.org>
The dma channel selection filter function is moved from plat-samsung
into the pl330 driver. In additon to that, a check is added in the
filter function to ensure that the channel on which the filter has
been invoked is pl330 channel instance (and avoid any incorrect
access of chan->private in a system with multiple types of DMA
drivers).
Suggested-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Jassi Brar <jassisinghbrar@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
---
arch/arm/plat-samsung/dma-ops.c | 6 ------
drivers/dma/pl330.c | 15 +++++++++++++++
include/linux/amba/pl330.h | 2 ++
3 files changed, 17 insertions(+), 6 deletions(-)
diff --git a/arch/arm/plat-samsung/dma-ops.c b/arch/arm/plat-samsung/dma-ops.c
index 6e3d9ab..8d18425 100644
--- a/arch/arm/plat-samsung/dma-ops.c
+++ b/arch/arm/plat-samsung/dma-ops.c
@@ -17,12 +17,6 @@
#include <mach/dma.h>
-static inline bool pl330_filter(struct dma_chan *chan, void *param)
-{
- struct dma_pl330_peri *peri = chan->private;
- return peri->peri_id == (unsigned)param;
-}
-
static unsigned samsung_dmadev_request(enum dma_ch dma_ch,
struct samsung_dma_info *info)
{
diff --git a/drivers/dma/pl330.c b/drivers/dma/pl330.c
index 621134f..5f1d24c 100644
--- a/drivers/dma/pl330.c
+++ b/drivers/dma/pl330.c
@@ -116,6 +116,9 @@ struct dma_pl330_desc {
struct dma_pl330_chan *pchan;
};
+/* forward declaration */
+static struct amba_driver pl330_driver;
+
static inline struct dma_pl330_chan *
to_pchan(struct dma_chan *ch)
{
@@ -267,6 +270,18 @@ static void dma_pl330_rqcb(void *token, enum pl330_op_err err)
tasklet_schedule(&pch->task);
}
+bool pl330_filter(struct dma_chan *chan, void *param)
+{
+ struct dma_pl330_peri *peri;
+
+ if (chan->device->dev->driver != &pl330_driver.drv)
+ return false;
+
+ peri = chan->private;
+ return peri->peri_id == (unsigned)param;
+}
+EXPORT_SYMBOL(pl330_filter);
+
static int pl330_alloc_chan_resources(struct dma_chan *chan)
{
struct dma_pl330_chan *pch = to_pchan(chan);
diff --git a/include/linux/amba/pl330.h b/include/linux/amba/pl330.h
index d12f077..6db72da 100644
--- a/include/linux/amba/pl330.h
+++ b/include/linux/amba/pl330.h
@@ -12,6 +12,7 @@
#ifndef __AMBA_PL330_H_
#define __AMBA_PL330_H_
+#include <linux/dmaengine.h>
#include <asm/hardware/pl330.h>
struct dma_pl330_peri {
@@ -38,4 +39,5 @@ struct dma_pl330_platdata {
unsigned mcbuf_sz;
};
+extern bool pl330_filter(struct dma_chan *chan, void *param);
#endif /* __AMBA_PL330_H_ */
--
1.6.6.rc2
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox