* [PATCH 2/2] ARM: davinci: da850: configure CS2(aemif) for norflash
From: Heiko Schocher @ 2013-01-29 8:02 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359436796-25135-3-git-send-email-anilkumar.v@ti.com>
Hello Kumar,
On 29.01.2013 06:19, Kumar, Anil wrote:
> Configure 16 bit data bus width for CS2(aemif) to use the norflash on
> DA850.
>
> Signed-off-by: Kumar, Anil <anilkumar.v@ti.com>
> ---
> :100644 100644 37c27af... 540e284... M arch/arm/mach-davinci/da8xx-dt.c
> arch/arm/mach-davinci/da8xx-dt.c | 17 +++++++++++++++++
> 1 files changed, 17 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/mach-davinci/da8xx-dt.c b/arch/arm/mach-davinci/da8xx-dt.c
> index 37c27af..540e284 100644
> --- a/arch/arm/mach-davinci/da8xx-dt.c
> +++ b/arch/arm/mach-davinci/da8xx-dt.c
> @@ -38,12 +38,29 @@ static void __init da8xx_init_irq(void)
> }
>
> #ifdef CONFIG_ARCH_DAVINCI_DA850
> +#define DA8XX_AEMIF_CE2CFG_OFFSET 0x10
> +#define DA8XX_AEMIF_ASIZE_16BIT 0x1
Hmm... I am not really happy with such defines, because different
boards need maybe different settings, and this should be catched
by the device tree ... Couldn't we add this infos in the
device tree? I tried such an approach here:
First post and some discussion:
https://lists.ozlabs.org/pipermail/devicetree-discuss/2011-December/010030.html
Nori suggested here
https://lists.ozlabs.org/pipermail/devicetree-discuss/2011-December/011330.html
to move such an driver out of arch/arm and IIRC it was
suggested to move it into the mfd framework. I currently
not know, if there was such a sort of patches, to get this
in the mfd subsystem, but I think, this CS settings should be
done like the pinmux settings ...
My last posted version of this patch:
https://lists.ozlabs.org/pipermail/devicetree-discuss/2012-March/013036.html
Maybe it is worth to discuss this again?
> +
> +static void __init da8xx_init_nor(void)
> +{
> + void __iomem *aemif_addr;
> +
> + aemif_addr = ioremap(DA8XX_AEMIF_CTL_BASE, SZ_32K);
> +
> + /* Configure data bus width of CS2 to 16 bit */
> + writel(readl(aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET) |
> + DA8XX_AEMIF_ASIZE_16BIT,
> + aemif_addr + DA8XX_AEMIF_CE2CFG_OFFSET);
I vote for avoiding such board specific code in a generic
approach ...
> +
> + iounmap(aemif_addr);
> +}
>
> static void __init da850_init_machine(void)
> {
> of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
>
> da8xx_uart_clk_enable();
> + da8xx_init_nor();
> }
>
> static const char *da850_boards_compat[] __initdata = {
>
bye,
Heiko
--
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
^ permalink raw reply
* [PATCH V2] ARM: davinci: da850: add RTC DT entries
From: Sekhar Nori @ 2013-01-29 8:01 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <4232EB8829679242B82E712C3DB3149D42355C@DBDE01.ent.ti.com>
On 1/29/2013 1:05 PM, Katepallewar, Mrugesh wrote:
> On Mon, Jan 28, 2013 at 21:32:13, Nori, Sekhar wrote:
>> Hi Mrugesh,
>>
>> On 1/28/2013 1:17 PM, Mrugesh Katepallewar wrote:
>>> Add RTC DT entries in da850 dts file.
>>>
>>> Signed-off-by: Mrugesh Katepallewar <mrugesh.mk@ti.com>
>>> ---
>>> Applies on top of v3.8-rc4 of linus tree.
>>>
>>> This patch is depending on
>>> "ARM: davinci: da850: add interrupt-parent property in soc node"
>>> https://patchwork.kernel.org/patch/2044101/
>>
>>> Tested on da850-evm device.
>>>
>>> Test Procedure:
>>> date 2013.01.28-10:00:00 (usage: date[YYYY.]MM.DD-hh:mm[:ss]) hwclock
>>> -w reset board and check system time.
>>
>> Queuing this for v3.9. The testing information above is useful and should be part of the changelog. I moved it there while committing.
>>
>> It will be nice to check the alarm functionality as well. Can you check that and let me know that works as well?
>
> I tried to test RTC alarm using "rtcwake" command, however it is not working and returning following error
> "rtcwake: /dev/rtc0 not enabled for wakeup events"
> This is coming because we have not registered RTC device as a wakeup source yet.
rtcwake is too much to use if the purpose is just to test the alarm
functionality.
> For checking RTC alarm interrupt, I developed one simple program which opens RTC device, set alarm and exits.
> Then by entering "cat /proc/interrupts" checked RTC interrupt count.
No need of writing your own. Simply use the one in Documentation/rtc.txt
> Using above test it confirms that RTC alarm functionality is working fine.
Okay. Thanks for confirming.
Regards,
Sekhar
^ permalink raw reply
* [PATCH v2 19/27] pci: PCIe driver for Marvell Armada 370/XP systems
From: Thomas Petazzoni @ 2013-01-29 8:00 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20130129055508.GA3339@obsidianresearch.com>
Bjorn, Jason,
On Mon, 28 Jan 2013 22:55:08 -0700, Jason Gunthorpe wrote:
> > There's no Linux requirement that multiple PCIe interfaces appear to
> > be in the same hierarchy. You can just use pci_scan_root_bus()
> > separately on each interface. Each interface can be in its own domain
> > if necessary.
>
> What you suggest is basically what the Marvell driver did originally,
> the probelm is that Linux requires a pre-assigned aperture for each
> PCI domain/root bus, and these new chips have so many PCI-E ports that
> they can exhaust the physical address space, and also a limited
> internal HW resource for setting address routing.
>
> Thus they require resource allocation that is sensitive to the devices
> present downstream.
>
> By far the simplest solution is to merge all the physical links into a
> single domain and rely on existing PCI resource allocation code to
> drive allocation of scarce physical address space and demand allocate
> the HW routing resource (specifically there are enough resources to
> accomidate MMIO only devices on every bus, but not enough to
> accomidate MMIO and IO on every bus).
>
> > > +/*
> > > + * For a given PCIe interface (represented by a mvebu_pcie_port
> > > + * structure), we read the PCI configuration space of the
> > > + * corresponding PCI-to-PCI bridge in order to find out which range of
> > > + * I/O addresses and memory addresses have been assigned to this PCIe
> > > + * interface. Using these informations, we set up the appropriate
> > > + * address decoding windows so that the physical address are actually
> > > + * resolved to the right PCIe interface.
> > > + */
> >
> > Are you inferring the host bridge apertures by using the resources
> > assigned to devices under the bridge, i.e., taking the union of all
>
> The flow is different, a portion of physical address space is set
> aside for use by PCI-E (via DT) and that portion is specified in the
> struct resource's ultimately attached to the PCI domain for the bus
> scan. You could call that the 'host bridge aperture' though it doesn't
> reflect any HW configuration at all. The values come from the device
> tree.
>
> During the bus scan the Linux core code splits up that contiguous
> space and assigns to the PCI-PCI bridges and devices under that domain.
>
> Each physical PCI-E link on the chip is seen by Linux through the SW
> emulated PCI-PCI bridge attached to bus 0. When Linux configures the
> bridge windows it triggers this code here to copy that window
> information from the PCI config space into non-standard internal HW
> registers.
>
> The purpose of the SW PCI-PCI bridge and this code here is to give
> the Linux PCI core control over the window (MMIO,IO,busnr) assigned
> to the PCI-E link.
>
> This arrangement with PCI-PCI bridges controlling address routing is
> part of the PCI-E standard, in this instance Marvell did not implement
> the required config space in HW so the driver is working around that
> deficiency.
>
> Other drivers, like tegra have a similar design, but their hardware
> does implement PCI-PCI bridge configuration space and does drive
> address decoding through the HW PCI-PCI window registers.
>
> Having PCI-E links be bridges, not domains/root_bus's is in-line with
> the standard and works better with the Linux PCI resource allocator.
Thanks a lot Jason for this explanation, I couldn't have explained it
as clearly as you did.
Bjorn, does Jason's reply answers your questions? Or do you need other
details?
Thanks!
Thomas
--
Thomas Petazzoni, Free Electrons
Kernel, drivers, real-time and embedded Linux
development, consulting, training and support.
http://free-electrons.com
^ permalink raw reply
* [PATCH 2/2] ARM: dts: cfa10049: Change the SPI3 bus to spi-gpio
From: Shawn Guo @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359103175-26304-3-git-send-email-maxime.ripard@free-electrons.com>
On Fri, Jan 25, 2013 at 09:39:35AM +0100, Maxime Ripard wrote:
> The DAC found on the last chip select requires a word length of 12 bits,
> which is not supported by the SSP controller of the iMX28. Use
> bitbanging for that bus to support such a length.
>
> Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Applied, thanks.
^ permalink raw reply
* [PATCH v3 15/15] ARM: vexpress/dcscb: probe via device tree
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
This allows for the DCSCB support to be compiled in and selected
at run time.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/mach-vexpress/dcscb.c | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
diff --git a/arch/arm/mach-vexpress/dcscb.c b/arch/arm/mach-vexpress/dcscb.c
index 58051ffafb..a724507cbc 100644
--- a/arch/arm/mach-vexpress/dcscb.c
+++ b/arch/arm/mach-vexpress/dcscb.c
@@ -14,6 +14,7 @@
#include <linux/io.h>
#include <linux/spinlock.h>
#include <linux/errno.h>
+#include <linux/of_address.h>
#include <linux/vexpress.h>
#include <linux/arm-cci.h>
@@ -24,8 +25,6 @@
#include <asm/cp15.h>
-#define DCSCB_PHYS_BASE 0x60000000
-
#define RST_HOLD0 0x0
#define RST_HOLD1 0x4
#define SYS_SWRESET 0x8
@@ -215,10 +214,14 @@ extern void dcscb_power_up_setup(unsigned int affinity_level);
static int __init dcscb_init(void)
{
+ struct device_node *node;
unsigned int cfg;
int ret;
- dcscb_base = ioremap(DCSCB_PHYS_BASE, 0x1000);
+ node = of_find_compatible_node(NULL, NULL, "arm,dcscb");
+ if (!node)
+ return -ENODEV;
+ dcscb_base= of_iomap(node, 0);
if (!dcscb_base)
return -EADDRNOTAVAIL;
cfg = readl_relaxed(dcscb_base + DCS_CFG_R);
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 14/15] ARM: vexpress/dcscb: handle platform coherency exit/setup and CCI
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Dave Martin <dave.martin@linaro.org>
Add the required code to properly handle race free platform coherency exit
to the DCSCB power down method.
The power_up_setup callback is used to enable the CCI interface for
the cluster being brought up. This must be done in assembly before
the kernel environment is entered.
Thanks to Achin Gupta and Nicolas Pitre for their help and
contributions.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/mach-vexpress/Kconfig | 1 +
arch/arm/mach-vexpress/Makefile | 2 +-
arch/arm/mach-vexpress/dcscb.c | 74 ++++++++++++++++++++++++---------
arch/arm/mach-vexpress/dcscb_setup.S | 80 ++++++++++++++++++++++++++++++++++++
4 files changed, 137 insertions(+), 20 deletions(-)
create mode 100644 arch/arm/mach-vexpress/dcscb_setup.S
diff --git a/arch/arm/mach-vexpress/Kconfig b/arch/arm/mach-vexpress/Kconfig
index f3f92b120a..f8fbe7c6a2 100644
--- a/arch/arm/mach-vexpress/Kconfig
+++ b/arch/arm/mach-vexpress/Kconfig
@@ -55,6 +55,7 @@ config ARCH_VEXPRESS_CA9X4
config ARCH_VEXPRESS_DCSCB
bool "Dual Cluster System Control Block (DCSCB) support"
depends on CLUSTER_PM
+ select ARM_CCI
help
Support for the Dual Cluster System Configuration Block (DCSCB).
This is needed to provide CPU and cluster power management
diff --git a/arch/arm/mach-vexpress/Makefile b/arch/arm/mach-vexpress/Makefile
index 2253644054..f6e90f3272 100644
--- a/arch/arm/mach-vexpress/Makefile
+++ b/arch/arm/mach-vexpress/Makefile
@@ -6,6 +6,6 @@ ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
obj-y := v2m.o reset.o
obj-$(CONFIG_ARCH_VEXPRESS_CA9X4) += ct-ca9x4.o
-obj-$(CONFIG_ARCH_VEXPRESS_DCSCB) += dcscb.o
+obj-$(CONFIG_ARCH_VEXPRESS_DCSCB) += dcscb.o dcscb_setup.o
obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
diff --git a/arch/arm/mach-vexpress/dcscb.c b/arch/arm/mach-vexpress/dcscb.c
index 8d363357ef..58051ffafb 100644
--- a/arch/arm/mach-vexpress/dcscb.c
+++ b/arch/arm/mach-vexpress/dcscb.c
@@ -15,6 +15,7 @@
#include <linux/spinlock.h>
#include <linux/errno.h>
#include <linux/vexpress.h>
+#include <linux/arm-cci.h>
#include <asm/mcpm_entry.h>
#include <asm/proc-fns.h>
@@ -106,6 +107,8 @@ static void dcscb_power_down(void)
pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
BUG_ON(cpu >= 4 || cluster >= 2);
+ __mcpm_cpu_going_down(cpu, cluster);
+
arch_spin_lock(&dcscb_lock);
dcscb_use_count[cpu][cluster]--;
if (dcscb_use_count[cpu][cluster] == 0) {
@@ -113,6 +116,7 @@ static void dcscb_power_down(void)
rst_hold |= cpumask;
if (((rst_hold | (rst_hold >> 4)) & mcpm_mask) == mcpm_mask) {
rst_hold |= (1 << 8);
+ BUG_ON(__mcpm_mcpm_state(cluster) != CLUSTER_UP);
last_man = true;
}
writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
@@ -126,31 +130,59 @@ static void dcscb_power_down(void)
skip_wfi = true;
} else
BUG();
- arch_spin_unlock(&dcscb_lock);
- /*
- * Now let's clean our L1 cache and shut ourself down.
- * If we're the last CPU in this cluster then clean L2 too.
- */
-
- /*
- * A15/A7 can hit in the cache with SCTLR.C=0, so we don't need
- * a preliminary flush here for those CPUs. At least, that's
- * the theory -- without the extra flush, Linux explodes on
- * RTSM (maybe not needed anymore, to be investigated)..
- */
- flush_cache_louis();
- cpu_proc_fin();
+ if (last_man && __mcpm_outbound_enter_critical(cpu, cluster)) {
+ arch_spin_unlock(&dcscb_lock);
- if (!last_man) {
- flush_cache_louis();
- } else {
+ /*
+ * Flush all cache levels for this cluster.
+ *
+ * A15/A7 can hit in the cache with SCTLR.C=0, so we don't need
+ * a preliminary flush here for those CPUs. At least, that's
+ * the theory -- without the extra flush, Linux explodes on
+ * RTSM (maybe not needed anymore, to be investigated).
+ */
flush_cache_all();
+ cpu_proc_fin(); /* disable allocation into internal caches*/
+ flush_cache_all();
+
+ /*
+ * This is a harmless no-op. On platforms with a real
+ * outer cache this might either be needed or not,
+ * depending on where the outer cache sits.
+ */
outer_flush_all();
+
+ /* Disable local coherency by clearing the ACTLR "SMP" bit: */
+ set_auxcr(get_auxcr() & ~(1 << 6));
+
+ /*
+ * Disable cluster-level coherency by masking
+ * incoming snoops and DVM messages:
+ */
+ disable_cci(cluster);
+
+ __mcpm_outbound_leave_critical(cluster, CLUSTER_DOWN);
+ } else {
+ arch_spin_unlock(&dcscb_lock);
+
+ /*
+ * Flush the local CPU cache.
+ *
+ * A15/A7 can hit in the cache with SCTLR.C=0, so we don't need
+ * a preliminary flush here for those CPUs. At least, that's
+ * the theory -- without the extra flush, Linux explodes on
+ * RTSM (maybe not needed anymore, to be investigated).
+ */
+ flush_cache_louis();
+ cpu_proc_fin(); /* disable allocation into internal caches*/
+ flush_cache_louis();
+
+ /* Disable local coherency by clearing the ACTLR "SMP" bit: */
+ set_auxcr(get_auxcr() & ~(1 << 6));
}
- /* Disable local coherency by clearing the ACTLR "SMP" bit: */
- set_auxcr(get_auxcr() & ~(1 << 6));
+ __mcpm_cpu_down(cpu, cluster);
/* Now we are prepared for power-down, do it: */
if (!skip_wfi) {
@@ -179,6 +211,8 @@ static void __init dcscb_usage_count_init(void)
dcscb_use_count[cpu][cluster] = 1;
}
+extern void dcscb_power_up_setup(unsigned int affinity_level);
+
static int __init dcscb_init(void)
{
unsigned int cfg;
@@ -193,6 +227,8 @@ static int __init dcscb_init(void)
dcscb_usage_count_init();
ret = mcpm_platform_register(&dcscb_power_ops);
+ if (!ret)
+ ret = mcpm_sync_init(dcscb_power_up_setup);
if (ret) {
iounmap(dcscb_base);
return ret;
diff --git a/arch/arm/mach-vexpress/dcscb_setup.S b/arch/arm/mach-vexpress/dcscb_setup.S
new file mode 100644
index 0000000000..cac033b982
--- /dev/null
+++ b/arch/arm/mach-vexpress/dcscb_setup.S
@@ -0,0 +1,80 @@
+/*
+ * arch/arm/include/asm/dcscb_setup.S
+ *
+ * Created by: Dave Martin, 2012-06-22
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+
+#include <linux/linkage.h>
+#include <asm/mcpm_entry.h>
+
+
+#define SLAVE_SNOOPCTL_OFFSET 0
+#define SNOOPCTL_SNOOP_ENABLE (1 << 0)
+#define SNOOPCTL_DVM_ENABLE (1 << 1)
+
+#define CCI_STATUS_OFFSET 0xc
+#define STATUS_CHANGE_PENDING (1 << 0)
+
+#define CCI_SLAVE_OFFSET(n) (0x1000 + 0x1000 * (n))
+
+#define RTSM_CCI_PHYS_BASE 0x2c090000
+#define RTSM_CCI_SLAVE_A15 3
+#define RTSM_CCI_SLAVE_A7 4
+
+#define RTSM_CCI_A15_OFFSET CCI_SLAVE_OFFSET(RTSM_CCI_SLAVE_A15)
+#define RTSM_CCI_A7_OFFSET CCI_SLAVE_OFFSET(RTSM_CCI_SLAVE_A7)
+
+
+ENTRY(dcscb_power_up_setup)
+
+ cmp r0, #0 @ check affinity level
+ beq 2f
+
+/*
+ * Enable cluster-level coherency, in preparation for turning on the MMU.
+ * The ACTLR SMP bit does not need to be set here, because cpu_resume()
+ * already restores that.
+ */
+
+ mrc p15, 0, r0, c0, c0, 5 @ MPIDR
+ ubfx r0, r0, #8, #4 @ cluster
+
+ @ A15/A7 may not require explicit L2 invalidation on reset, dependent
+ @ on hardware integration desicions.
+ @ For now, this code assumes that L2 is either already invalidated, or
+ @ invalidation is not required.
+
+ ldr r3, =RTSM_CCI_PHYS_BASE + RTSM_CCI_A15_OFFSET
+ cmp r0, #0 @ A15 cluster?
+ addne r3, r3, #RTSM_CCI_A7_OFFSET - RTSM_CCI_A15_OFFSET
+
+ @ r3 now points to the correct CCI slave register block
+
+ ldr r0, [r3, #SLAVE_SNOOPCTL_OFFSET]
+ orr r0, r0, #SNOOPCTL_SNOOP_ENABLE | SNOOPCTL_DVM_ENABLE
+ str r0, [r3, #SLAVE_SNOOPCTL_OFFSET] @ enable CCI snoops
+
+ @ Wait for snoop control change to complete:
+
+ ldr r3, =RTSM_CCI_PHYS_BASE
+
+1: ldr r0, [r3, #CCI_STATUS_OFFSET]
+ tst r0, #STATUS_CHANGE_PENDING
+ bne 1b
+
+ dsb @ Synchronise side-effects of enabling CCI
+
+ bx lr
+
+2: @ Implementation-specific local CPU setup operations should go here,
+ @ if any. In this case, there is nothing to do.
+
+ bx lr
+
+ENDPROC(dcscb_power_up_setup)
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 13/15] ARM: CCI: ensure powerdown-time data is flushed from cache
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Dave Martin <dave.martin@linaro.org>
Non-local variables used by the CCI management function called after
disabling the cache must be flushed out to main memory in advance,
otherwise incoherency of those values may occur if they are sitting
in the cache of some other CPU when cci_disable() executes.
This patch adds the appropriate flushing to the CCI driver to ensure
that the relevant data is available in RAM ahead of time.
Because this creates a dependency on arch-specific cacheflushing
functions, this patch also makes ARM_CCI depend on ARM.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
drivers/bus/Kconfig | 1 +
drivers/bus/arm-cci.c | 21 +++++++++++++++++++--
2 files changed, 20 insertions(+), 2 deletions(-)
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index d032f74ff2..cd4ac9f001 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -22,5 +22,6 @@ config OMAP_INTERCONNECT
config ARM_CCI
bool "ARM CCI driver support"
+ depends on ARM
endmenu
diff --git a/drivers/bus/arm-cci.c b/drivers/bus/arm-cci.c
index 25ae156924..30e4a77da0 100644
--- a/drivers/bus/arm-cci.c
+++ b/drivers/bus/arm-cci.c
@@ -21,8 +21,16 @@
#include <linux/slab.h>
#include <linux/arm-cci.h>
-#define CCI400_EAG_OFFSET 0x4000
-#define CCI400_KF_OFFSET 0x5000
+#include <asm/cacheflush.h>
+#include <asm/memory.h>
+#include <asm/outercache.h>
+
+#include <asm/irq_regs.h>
+#include <asm/pmu.h>
+
+#define CCI400_PMCR 0x0100
+#define CCI400_EAG_OFFSET 0x4000
+#define CCI400_KF_OFFSET 0x5000
#define DRIVER_NAME "CCI"
struct cci_drvdata {
@@ -73,6 +81,15 @@ static int cci_driver_probe(struct platform_device *pdev)
goto ioremap_err;
}
+ /*
+ * Multi-cluster systems may need this data when non-coherent, during
+ * cluster power-up/power-down. Make sure it reaches main memory:
+ */
+ __cpuc_flush_dcache_area(info, sizeof *info);
+ __cpuc_flush_dcache_area(&info, sizeof info);
+ outer_clean_range(virt_to_phys(info), virt_to_phys(info + 1));
+ outer_clean_range(virt_to_phys(&info), virt_to_phys(&info + 1));
+
platform_set_drvdata(pdev, info);
pr_info("CCI loaded at %p\n", info->baseaddr);
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 12/15] drivers/bus: add ARM CCI support
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
On ARM multi-cluster systems coherency between cores running on
different clusters is managed by the cache-coherent interconnect (CCI).
It allows broadcasting of TLB invalidates and memory barriers and it
guarantees cache coherency at system level.
This patch enables the basic infrastructure required in Linux to
handle and programme the CCI component. The first implementation is
based on a platform device, its relative DT compatible property and
a simple programming interface.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
drivers/bus/Kconfig | 4 ++
drivers/bus/Makefile | 2 +
drivers/bus/arm-cci.c | 107 ++++++++++++++++++++++++++++++++++++++++++++++++
include/linux/arm-cci.h | 30 ++++++++++++++
4 files changed, 143 insertions(+)
create mode 100644 drivers/bus/arm-cci.c
create mode 100644 include/linux/arm-cci.h
diff --git a/drivers/bus/Kconfig b/drivers/bus/Kconfig
index 0f51ed687d..d032f74ff2 100644
--- a/drivers/bus/Kconfig
+++ b/drivers/bus/Kconfig
@@ -19,4 +19,8 @@ config OMAP_INTERCONNECT
help
Driver to enable OMAP interconnect error handling driver.
+
+config ARM_CCI
+ bool "ARM CCI driver support"
+
endmenu
diff --git a/drivers/bus/Makefile b/drivers/bus/Makefile
index 45d997c854..55aac809e5 100644
--- a/drivers/bus/Makefile
+++ b/drivers/bus/Makefile
@@ -6,3 +6,5 @@ obj-$(CONFIG_OMAP_OCP2SCP) += omap-ocp2scp.o
# Interconnect bus driver for OMAP SoCs.
obj-$(CONFIG_OMAP_INTERCONNECT) += omap_l3_smx.o omap_l3_noc.o
+
+obj-$(CONFIG_ARM_CCI) += arm-cci.o
diff --git a/drivers/bus/arm-cci.c b/drivers/bus/arm-cci.c
new file mode 100644
index 0000000000..25ae156924
--- /dev/null
+++ b/drivers/bus/arm-cci.c
@@ -0,0 +1,107 @@
+/*
+ * ARM Cache Coherency Interconnect (CCI400) support
+ *
+ * Copyright (C) 2012-2013 ARM Ltd.
+ * Author: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed "as is" WITHOUT ANY WARRANTY of any
+ * kind, whether express or implied; without even the implied warranty
+ * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/device.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/slab.h>
+#include <linux/arm-cci.h>
+
+#define CCI400_EAG_OFFSET 0x4000
+#define CCI400_KF_OFFSET 0x5000
+
+#define DRIVER_NAME "CCI"
+struct cci_drvdata {
+ void __iomem *baseaddr;
+ spinlock_t lock;
+};
+
+static struct cci_drvdata *info;
+
+void disable_cci(int cluster)
+{
+ u32 cci_reg = cluster ? CCI400_KF_OFFSET : CCI400_EAG_OFFSET;
+ writel_relaxed(0x0, info->baseaddr + cci_reg);
+
+ while (readl_relaxed(info->baseaddr + 0xc) & 0x1)
+ ;
+}
+EXPORT_SYMBOL_GPL(disable_cci);
+
+static int cci_driver_probe(struct platform_device *pdev)
+{
+ struct resource *res;
+ int ret = 0;
+
+ info = kzalloc(sizeof(*info), GFP_KERNEL);
+ if (!info) {
+ dev_err(&pdev->dev, "unable to allocate mem\n");
+ return -ENOMEM;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ if (!res) {
+ dev_err(&pdev->dev, "No memory resource\n");
+ ret = -EINVAL;
+ goto mem_free;
+ }
+
+ if (!request_mem_region(res->start, resource_size(res),
+ dev_name(&pdev->dev))) {
+ dev_err(&pdev->dev, "address 0x%x in use\n", (u32) res->start);
+ ret = -EBUSY;
+ goto mem_free;
+ }
+
+ info->baseaddr = ioremap(res->start, resource_size(res));
+ if (!info->baseaddr) {
+ ret = -EADDRNOTAVAIL;
+ goto ioremap_err;
+ }
+
+ platform_set_drvdata(pdev, info);
+
+ pr_info("CCI loaded at %p\n", info->baseaddr);
+ return ret;
+
+ioremap_err:
+ release_region(res->start, resource_size(res));
+mem_free:
+ kfree(info);
+
+ return ret;
+}
+
+static const struct of_device_id arm_cci_matches[] = {
+ {.compatible = "arm,cci"},
+ {},
+};
+
+static struct platform_driver cci_platform_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .of_match_table = arm_cci_matches,
+ },
+ .probe = cci_driver_probe,
+};
+
+static int __init cci_init(void)
+{
+ return platform_driver_register(&cci_platform_driver);
+}
+
+core_initcall(cci_init);
diff --git a/include/linux/arm-cci.h b/include/linux/arm-cci.h
new file mode 100644
index 0000000000..86ae587817
--- /dev/null
+++ b/include/linux/arm-cci.h
@@ -0,0 +1,30 @@
+/*
+ * CCI support
+ *
+ * Copyright (C) 2012-2013 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA
+ */
+
+#ifndef __LINUX_ARM_CCI_H
+#define __LINUX_ARM_CCI_H
+
+#ifdef CONFIG_ARM_CCI
+extern void disable_cci(int cluster);
+#else
+static inline void disable_cci(int cluster) { }
+#endif
+
+#endif
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 11/15] ARM: vexpress/dcscb: do not hardcode number of CPUs per cluster
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
If 4 CPUs are assumed, the A15x1-A7x1 model configuration would never
shut down the initial cluster as the 0xf reset bit mask will never be
observed. Let's construct this mask based on the provided information
in the DCSCB config register for the number of CPUs per cluster.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/mach-vexpress/dcscb.c | 14 ++++++++++----
1 file changed, 10 insertions(+), 4 deletions(-)
diff --git a/arch/arm/mach-vexpress/dcscb.c b/arch/arm/mach-vexpress/dcscb.c
index f993608944..8d363357ef 100644
--- a/arch/arm/mach-vexpress/dcscb.c
+++ b/arch/arm/mach-vexpress/dcscb.c
@@ -46,10 +46,12 @@ static arch_spinlock_t dcscb_lock = __ARCH_SPIN_LOCK_UNLOCKED;
static void __iomem *dcscb_base;
static int dcscb_use_count[4][2];
+static int dcscb_mcpm_cpu_mask[2];
static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
{
unsigned int rst_hold, cpumask = (1 << cpu);
+ unsigned int mcpm_mask = dcscb_mcpm_cpu_mask[cluster];
pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
if (cpu >= 4 || cluster >= 2)
@@ -68,7 +70,7 @@ static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
if (rst_hold & (1 << 8)) {
/* remove cluster reset and add individual CPU's reset */
rst_hold &= ~(1 << 8);
- rst_hold |= 0xf;
+ rst_hold |= mcpm_mask;
}
rst_hold &= ~(cpumask | (cpumask << 4));
writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
@@ -92,13 +94,14 @@ static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
static void dcscb_power_down(void)
{
- unsigned int mpidr, cpu, cluster, rst_hold, cpumask;
+ unsigned int mpidr, cpu, cluster, rst_hold, cpumask, mcpm_mask;
bool last_man = false, skip_wfi = false;
mpidr = read_cpuid_mpidr();
cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0);
cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1);
cpumask = (1 << cpu);
+ mcpm_mask = dcscb_mcpm_cpu_mask[cluster];
pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
BUG_ON(cpu >= 4 || cluster >= 2);
@@ -108,7 +111,7 @@ static void dcscb_power_down(void)
if (dcscb_use_count[cpu][cluster] == 0) {
rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
rst_hold |= cpumask;
- if (((rst_hold | (rst_hold >> 4)) & 0xf) == 0xf) {
+ if (((rst_hold | (rst_hold >> 4)) & mcpm_mask) == mcpm_mask) {
rst_hold |= (1 << 8);
last_man = true;
}
@@ -178,12 +181,15 @@ static void __init dcscb_usage_count_init(void)
static int __init dcscb_init(void)
{
+ unsigned int cfg;
int ret;
dcscb_base = ioremap(DCSCB_PHYS_BASE, 0x1000);
if (!dcscb_base)
return -EADDRNOTAVAIL;
-
+ cfg = readl_relaxed(dcscb_base + DCS_CFG_R);
+ dcscb_mcpm_cpu_mask[0] = (1 << (((cfg >> 16) >> (0 << 2)) & 0xf)) - 1;
+ dcscb_mcpm_cpu_mask[1] = (1 << (((cfg >> 16) >> (1 << 2)) & 0xf)) - 1;
dcscb_usage_count_init();
ret = mcpm_platform_register(&dcscb_power_ops);
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 10/15] ARM: vexpress/dcscb: add CPU use counts to the power up/down API implementation
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
It is possible for a CPU to be told to power up before it managed
to power itself down. Solve this race with a usage count as mandated
by the API definition.
Signed-off-by: nicolas Pitre <nico@linaro.org>
---
arch/arm/mach-vexpress/dcscb.c | 77 +++++++++++++++++++++++++++++++++---------
1 file changed, 61 insertions(+), 16 deletions(-)
diff --git a/arch/arm/mach-vexpress/dcscb.c b/arch/arm/mach-vexpress/dcscb.c
index 677ced9efc..f993608944 100644
--- a/arch/arm/mach-vexpress/dcscb.c
+++ b/arch/arm/mach-vexpress/dcscb.c
@@ -45,6 +45,7 @@
static arch_spinlock_t dcscb_lock = __ARCH_SPIN_LOCK_UNLOCKED;
static void __iomem *dcscb_base;
+static int dcscb_use_count[4][2];
static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
{
@@ -61,14 +62,27 @@ static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
local_irq_disable();
arch_spin_lock(&dcscb_lock);
- rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
- if (rst_hold & (1 << 8)) {
- /* remove cluster reset and add individual CPU's reset */
- rst_hold &= ~(1 << 8);
- rst_hold |= 0xf;
+ dcscb_use_count[cpu][cluster]++;
+ if (dcscb_use_count[cpu][cluster] == 1) {
+ rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
+ if (rst_hold & (1 << 8)) {
+ /* remove cluster reset and add individual CPU's reset */
+ rst_hold &= ~(1 << 8);
+ rst_hold |= 0xf;
+ }
+ rst_hold &= ~(cpumask | (cpumask << 4));
+ writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
+ } else if (dcscb_use_count[cpu][cluster] != 2) {
+ /*
+ * The only possible values are:
+ * 0 = CPU down
+ * 1 = CPU (still) up
+ * 2 = CPU requested to be up before it had a chance
+ * to actually make itself down.
+ * Any other value is a bug.
+ */
+ BUG();
}
- rst_hold &= ~(cpumask | (cpumask << 4));
- writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
arch_spin_unlock(&dcscb_lock);
local_irq_enable();
@@ -78,7 +92,8 @@ static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
static void dcscb_power_down(void)
{
- unsigned int mpidr, cpu, cluster, rst_hold, cpumask, last_man;
+ unsigned int mpidr, cpu, cluster, rst_hold, cpumask;
+ bool last_man = false, skip_wfi = false;
mpidr = read_cpuid_mpidr();
cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0);
@@ -89,13 +104,26 @@ static void dcscb_power_down(void)
BUG_ON(cpu >= 4 || cluster >= 2);
arch_spin_lock(&dcscb_lock);
- rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
- rst_hold |= cpumask;
- if (((rst_hold | (rst_hold >> 4)) & 0xf) == 0xf)
- rst_hold |= (1 << 8);
- writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
+ dcscb_use_count[cpu][cluster]--;
+ if (dcscb_use_count[cpu][cluster] == 0) {
+ rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
+ rst_hold |= cpumask;
+ if (((rst_hold | (rst_hold >> 4)) & 0xf) == 0xf) {
+ rst_hold |= (1 << 8);
+ last_man = true;
+ }
+ writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
+ } else if (dcscb_use_count[cpu][cluster] == 1) {
+ /*
+ * A power_up request went ahead of us.
+ * Even if we do not want to shut this CPU down,
+ * the caller expects a certain state as if the WFI
+ * was aborted. So let's continue with cache cleaning.
+ */
+ skip_wfi = true;
+ } else
+ BUG();
arch_spin_unlock(&dcscb_lock);
- last_man = (rst_hold & (1 << 8));
/*
* Now let's clean our L1 cache and shut ourself down.
@@ -122,8 +150,10 @@ static void dcscb_power_down(void)
set_auxcr(get_auxcr() & ~(1 << 6));
/* Now we are prepared for power-down, do it: */
- dsb();
- wfi();
+ if (!skip_wfi) {
+ dsb();
+ wfi();
+ }
/* Not dead@this point? Let our caller cope. */
}
@@ -133,6 +163,19 @@ static const struct mcpm_platform_ops dcscb_power_ops = {
.power_down = dcscb_power_down,
};
+static void __init dcscb_usage_count_init(void)
+{
+ unsigned int mpidr, cpu, cluster;
+
+ mpidr = read_cpuid_mpidr();
+ cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0);
+ cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1);
+
+ pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
+ BUG_ON(cpu >= 4 || cluster >= 2);
+ dcscb_use_count[cpu][cluster] = 1;
+}
+
static int __init dcscb_init(void)
{
int ret;
@@ -141,6 +184,8 @@ static int __init dcscb_init(void)
if (!dcscb_base)
return -EADDRNOTAVAIL;
+ dcscb_usage_count_init();
+
ret = mcpm_platform_register(&dcscb_power_ops);
if (ret) {
iounmap(dcscb_base);
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 09/15] ARM: vexpress: introduce DCSCB support
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
This adds basic CPU and cluster reset controls on RTSM for the
A15x4-A7x4 model configuration using the Dual Cluster System
Configuration Block (DCSCB).
The cache coherency interconnect (CCI) is not handled yet.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/mach-vexpress/Kconfig | 8 ++
arch/arm/mach-vexpress/Makefile | 1 +
arch/arm/mach-vexpress/dcscb.c | 159 ++++++++++++++++++++++++++++++++++++++++
3 files changed, 168 insertions(+)
create mode 100644 arch/arm/mach-vexpress/dcscb.c
diff --git a/arch/arm/mach-vexpress/Kconfig b/arch/arm/mach-vexpress/Kconfig
index 52d315b792..f3f92b120a 100644
--- a/arch/arm/mach-vexpress/Kconfig
+++ b/arch/arm/mach-vexpress/Kconfig
@@ -52,4 +52,12 @@ config ARCH_VEXPRESS_CORTEX_A5_A9_ERRATA
config ARCH_VEXPRESS_CA9X4
bool "Versatile Express Cortex-A9x4 tile"
+config ARCH_VEXPRESS_DCSCB
+ bool "Dual Cluster System Control Block (DCSCB) support"
+ depends on CLUSTER_PM
+ help
+ Support for the Dual Cluster System Configuration Block (DCSCB).
+ This is needed to provide CPU and cluster power management
+ on RTSM.
+
endmenu
diff --git a/arch/arm/mach-vexpress/Makefile b/arch/arm/mach-vexpress/Makefile
index 80b64971fb..2253644054 100644
--- a/arch/arm/mach-vexpress/Makefile
+++ b/arch/arm/mach-vexpress/Makefile
@@ -6,5 +6,6 @@ ccflags-$(CONFIG_ARCH_MULTIPLATFORM) := -I$(srctree)/$(src)/include \
obj-y := v2m.o reset.o
obj-$(CONFIG_ARCH_VEXPRESS_CA9X4) += ct-ca9x4.o
+obj-$(CONFIG_ARCH_VEXPRESS_DCSCB) += dcscb.o
obj-$(CONFIG_SMP) += platsmp.o
obj-$(CONFIG_HOTPLUG_CPU) += hotplug.o
diff --git a/arch/arm/mach-vexpress/dcscb.c b/arch/arm/mach-vexpress/dcscb.c
new file mode 100644
index 0000000000..677ced9efc
--- /dev/null
+++ b/arch/arm/mach-vexpress/dcscb.c
@@ -0,0 +1,159 @@
+/*
+ * arch/arm/mach-vexpress/dcscb.c - Dual Cluster System Control Block
+ *
+ * Created by: Nicolas Pitre, May 2012
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/io.h>
+#include <linux/spinlock.h>
+#include <linux/errno.h>
+#include <linux/vexpress.h>
+
+#include <asm/mcpm_entry.h>
+#include <asm/proc-fns.h>
+#include <asm/cacheflush.h>
+#include <asm/cputype.h>
+#include <asm/cp15.h>
+
+
+#define DCSCB_PHYS_BASE 0x60000000
+
+#define RST_HOLD0 0x0
+#define RST_HOLD1 0x4
+#define SYS_SWRESET 0x8
+#define RST_STAT0 0xc
+#define RST_STAT1 0x10
+#define EAG_CFG_R 0x20
+#define EAG_CFG_W 0x24
+#define KFC_CFG_R 0x28
+#define KFC_CFG_W 0x2c
+#define DCS_CFG_R 0x30
+
+/*
+ * We can't use regular spinlocks. In the switcher case, it is possible
+ * for an outbound CPU to call power_down() after its inbound counterpart
+ * is already live using the same logical CPU number which trips lockdep
+ * debugging.
+ */
+static arch_spinlock_t dcscb_lock = __ARCH_SPIN_LOCK_UNLOCKED;
+
+static void __iomem *dcscb_base;
+
+static int dcscb_power_up(unsigned int cpu, unsigned int cluster)
+{
+ unsigned int rst_hold, cpumask = (1 << cpu);
+
+ pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
+ if (cpu >= 4 || cluster >= 2)
+ return -EINVAL;
+
+ /*
+ * Since this is called with IRQs enabled, and no arch_spin_lock_irq
+ * variant exists, we need to disable IRQs manually here.
+ */
+ local_irq_disable();
+ arch_spin_lock(&dcscb_lock);
+
+ rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
+ if (rst_hold & (1 << 8)) {
+ /* remove cluster reset and add individual CPU's reset */
+ rst_hold &= ~(1 << 8);
+ rst_hold |= 0xf;
+ }
+ rst_hold &= ~(cpumask | (cpumask << 4));
+ writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
+
+ arch_spin_unlock(&dcscb_lock);
+ local_irq_enable();
+
+ return 0;
+}
+
+static void dcscb_power_down(void)
+{
+ unsigned int mpidr, cpu, cluster, rst_hold, cpumask, last_man;
+
+ mpidr = read_cpuid_mpidr();
+ cpu = MPIDR_AFFINITY_LEVEL(mpidr, 0);
+ cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1);
+ cpumask = (1 << cpu);
+
+ pr_debug("%s: cpu %u cluster %u\n", __func__, cpu, cluster);
+ BUG_ON(cpu >= 4 || cluster >= 2);
+
+ arch_spin_lock(&dcscb_lock);
+ rst_hold = readl_relaxed(dcscb_base + RST_HOLD0 + cluster * 4);
+ rst_hold |= cpumask;
+ if (((rst_hold | (rst_hold >> 4)) & 0xf) == 0xf)
+ rst_hold |= (1 << 8);
+ writel(rst_hold, dcscb_base + RST_HOLD0 + cluster * 4);
+ arch_spin_unlock(&dcscb_lock);
+ last_man = (rst_hold & (1 << 8));
+
+ /*
+ * Now let's clean our L1 cache and shut ourself down.
+ * If we're the last CPU in this cluster then clean L2 too.
+ */
+
+ /*
+ * A15/A7 can hit in the cache with SCTLR.C=0, so we don't need
+ * a preliminary flush here for those CPUs. At least, that's
+ * the theory -- without the extra flush, Linux explodes on
+ * RTSM (maybe not needed anymore, to be investigated)..
+ */
+ flush_cache_louis();
+ cpu_proc_fin();
+
+ if (!last_man) {
+ flush_cache_louis();
+ } else {
+ flush_cache_all();
+ outer_flush_all();
+ }
+
+ /* Disable local coherency by clearing the ACTLR "SMP" bit: */
+ set_auxcr(get_auxcr() & ~(1 << 6));
+
+ /* Now we are prepared for power-down, do it: */
+ dsb();
+ wfi();
+
+ /* Not dead@this point? Let our caller cope. */
+}
+
+static const struct mcpm_platform_ops dcscb_power_ops = {
+ .power_up = dcscb_power_up,
+ .power_down = dcscb_power_down,
+};
+
+static int __init dcscb_init(void)
+{
+ int ret;
+
+ dcscb_base = ioremap(DCSCB_PHYS_BASE, 0x1000);
+ if (!dcscb_base)
+ return -EADDRNOTAVAIL;
+
+ ret = mcpm_platform_register(&dcscb_power_ops);
+ if (ret) {
+ iounmap(dcscb_base);
+ return ret;
+ }
+
+ /*
+ * Future entries into the kernel can now go
+ * through the cluster entry vectors.
+ */
+ vexpress_flags_set(virt_to_phys(mcpm_entry_point));
+
+ return 0;
+}
+
+early_initcall(dcscb_init);
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 08/15] ARM: introduce common set_auxcr/get_auxcr functions
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Rob Herring <rob.herring@calxeda.com>
Move the private set_auxcr/get_auxcr functions from
drivers/cpuidle/cpuidle-calxeda.c so they can be used across platforms.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/include/asm/cp15.h | 14 ++++++++++++++
drivers/cpuidle/cpuidle-calxeda.c | 14 --------------
2 files changed, 14 insertions(+), 14 deletions(-)
diff --git a/arch/arm/include/asm/cp15.h b/arch/arm/include/asm/cp15.h
index 5ef4d8015a..ce4d01c03e 100644
--- a/arch/arm/include/asm/cp15.h
+++ b/arch/arm/include/asm/cp15.h
@@ -59,6 +59,20 @@ static inline void set_cr(unsigned int val)
isb();
}
+static inline unsigned int get_auxcr(void)
+{
+ unsigned int val;
+ asm("mrc p15, 0, %0, c1, c0, 1 @ get AUXCR" : "=r" (val));
+ return val;
+}
+
+static inline void set_auxcr(unsigned int val)
+{
+ asm volatile("mcr p15, 0, %0, c1, c0, 1 @ set AUXCR"
+ : : "r" (val));
+ isb();
+}
+
#ifndef CONFIG_SMP
extern void adjust_cr(unsigned long mask, unsigned long set);
#endif
diff --git a/drivers/cpuidle/cpuidle-calxeda.c b/drivers/cpuidle/cpuidle-calxeda.c
index e1aab38c5a..ece83d6e04 100644
--- a/drivers/cpuidle/cpuidle-calxeda.c
+++ b/drivers/cpuidle/cpuidle-calxeda.c
@@ -37,20 +37,6 @@ extern void *scu_base_addr;
static struct cpuidle_device __percpu *calxeda_idle_cpuidle_devices;
-static inline unsigned int get_auxcr(void)
-{
- unsigned int val;
- asm("mrc p15, 0, %0, c1, c0, 1 @ get AUXCR" : "=r" (val) : : "cc");
- return val;
-}
-
-static inline void set_auxcr(unsigned int val)
-{
- asm volatile("mcr p15, 0, %0, c1, c0, 1 @ set AUXCR"
- : : "r" (val) : "cc");
- isb();
-}
-
static noinline void calxeda_idle_restore(void)
{
set_cr(get_cr() | CR_C);
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 07/15] ARM: vexpress: Select the correct SMP operations at run-time
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Jon Medhurst <tixy@linaro.org>
---
arch/arm/include/asm/mach/arch.h | 3 +++
arch/arm/kernel/setup.c | 5 ++++-
arch/arm/mach-vexpress/core.h | 2 ++
arch/arm/mach-vexpress/platsmp.c | 12 ++++++++++++
arch/arm/mach-vexpress/v2m.c | 2 +-
5 files changed, 22 insertions(+), 2 deletions(-)
diff --git a/arch/arm/include/asm/mach/arch.h b/arch/arm/include/asm/mach/arch.h
index 917d4fcfd9..3d01c6d6c3 100644
--- a/arch/arm/include/asm/mach/arch.h
+++ b/arch/arm/include/asm/mach/arch.h
@@ -17,8 +17,10 @@ struct pt_regs;
struct smp_operations;
#ifdef CONFIG_SMP
#define smp_ops(ops) (&(ops))
+#define smp_init_ops(ops) (&(ops))
#else
#define smp_ops(ops) (struct smp_operations *)NULL
+#define smp_init_ops(ops) (void (*)(void))NULL
#endif
struct machine_desc {
@@ -42,6 +44,7 @@ struct machine_desc {
unsigned char reserve_lp2 :1; /* never has lp2 */
char restart_mode; /* default restart mode */
struct smp_operations *smp; /* SMP operations */
+ void (*smp_init)(void);
void (*fixup)(struct tag *, char **,
struct meminfo *);
void (*reserve)(void);/* reserve mem blocks */
diff --git a/arch/arm/kernel/setup.c b/arch/arm/kernel/setup.c
index 3f6cbb2e3e..41edca8582 100644
--- a/arch/arm/kernel/setup.c
+++ b/arch/arm/kernel/setup.c
@@ -768,7 +768,10 @@ void __init setup_arch(char **cmdline_p)
arm_dt_init_cpu_maps();
#ifdef CONFIG_SMP
if (is_smp()) {
- smp_set_ops(mdesc->smp);
+ if(mdesc->smp_init)
+ (*mdesc->smp_init)();
+ else
+ smp_set_ops(mdesc->smp);
smp_init_cpus();
}
#endif
diff --git a/arch/arm/mach-vexpress/core.h b/arch/arm/mach-vexpress/core.h
index f134cd4a85..3a761fd76c 100644
--- a/arch/arm/mach-vexpress/core.h
+++ b/arch/arm/mach-vexpress/core.h
@@ -6,6 +6,8 @@
void vexpress_dt_smp_map_io(void);
+void vexpress_smp_init_ops(void);
+
extern struct smp_operations vexpress_smp_ops;
extern void vexpress_cpu_die(unsigned int cpu);
diff --git a/arch/arm/mach-vexpress/platsmp.c b/arch/arm/mach-vexpress/platsmp.c
index c5d70de9bb..667344b479 100644
--- a/arch/arm/mach-vexpress/platsmp.c
+++ b/arch/arm/mach-vexpress/platsmp.c
@@ -12,6 +12,7 @@
#include <linux/errno.h>
#include <linux/smp.h>
#include <linux/io.h>
+#include <linux/of.h>
#include <linux/of_fdt.h>
#include <linux/vexpress.h>
@@ -206,3 +207,14 @@ struct smp_operations __initdata vexpress_smp_ops = {
.cpu_die = vexpress_cpu_die,
#endif
};
+
+void __init vexpress_smp_init_ops(void)
+{
+ struct smp_operations *ops = &vexpress_smp_ops;
+#ifdef CONFIG_CLUSTER_PM
+ extern struct smp_operations mcpm_smp_ops;
+ if(of_find_compatible_node(NULL, NULL, "arm,cci"))
+ ops = &mcpm_smp_ops;
+#endif
+ smp_set_ops(ops);
+}
diff --git a/arch/arm/mach-vexpress/v2m.c b/arch/arm/mach-vexpress/v2m.c
index 011661a6c5..34172bd504 100644
--- a/arch/arm/mach-vexpress/v2m.c
+++ b/arch/arm/mach-vexpress/v2m.c
@@ -494,7 +494,7 @@ static const char * const v2m_dt_match[] __initconst = {
DT_MACHINE_START(VEXPRESS_DT, "ARM-Versatile Express")
.dt_compat = v2m_dt_match,
- .smp = smp_ops(vexpress_smp_ops),
+ .smp_init = smp_init_ops(vexpress_smp_init_ops),
.map_io = v2m_dt_map_io,
.init_early = v2m_dt_init_early,
.init_irq = v2m_dt_init_irq,
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 06/15] ARM: mcpm: generic SMP secondary bringup and hotplug support
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
Now that the cluster power API is in place, we can use it for SMP secondary
bringup and CPU hotplug in a generic fashion.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/common/Makefile | 2 +-
arch/arm/common/mcpm_platsmp.c | 85 ++++++++++++++++++++++++++++++++++++++++++
2 files changed, 86 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/common/mcpm_platsmp.c
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index c901a38c59..e1c9db45de 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -13,4 +13,4 @@ obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
obj-$(CONFIG_SHARP_SCOOP) += scoop.o
obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o
obj-$(CONFIG_ARM_TIMER_SP804) += timer-sp.o
-obj-$(CONFIG_CLUSTER_PM) += mcpm_head.o mcpm_entry.o vlock.o
+obj-$(CONFIG_CLUSTER_PM) += mcpm_head.o mcpm_entry.o mcpm_platsmp.o vlock.o
diff --git a/arch/arm/common/mcpm_platsmp.c b/arch/arm/common/mcpm_platsmp.c
new file mode 100644
index 0000000000..401298f5ee
--- /dev/null
+++ b/arch/arm/common/mcpm_platsmp.c
@@ -0,0 +1,85 @@
+/*
+ * linux/arch/arm/mach-vexpress/mcpm_platsmp.c
+ *
+ * Created by: Nicolas Pitre, November 2012
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * Code to handle secondary CPU bringup and hotplug for the cluster power API.
+ */
+
+#include <linux/init.h>
+#include <linux/smp.h>
+
+#include <asm/mcpm_entry.h>
+#include <asm/smp_plat.h>
+#include <asm/hardware/gic.h>
+
+static void __init simple_smp_init_cpus(void)
+{
+ set_smp_cross_call(gic_raise_softirq);
+}
+
+static int __cpuinit mcpm_boot_secondary(unsigned int cpu, struct task_struct *idle)
+{
+ unsigned int mpidr, pcpu, pcluster, ret;
+ extern void secondary_startup(void);
+
+ mpidr = cpu_logical_map(cpu);
+ pcpu = MPIDR_AFFINITY_LEVEL(mpidr, 0);
+ pcluster = MPIDR_AFFINITY_LEVEL(mpidr, 1);
+ pr_debug("%s: logical CPU %d is physical CPU %d cluster %d\n",
+ __func__, cpu, pcpu, pcluster);
+
+ mcpm_set_entry_vector(pcpu, pcluster, NULL);
+ ret = mcpm_cpu_power_up(pcpu, pcluster);
+ if (ret)
+ return ret;
+ mcpm_set_entry_vector(pcpu, pcluster, secondary_startup);
+ gic_raise_softirq(cpumask_of(cpu), 0);
+ dsb_sev();
+ return 0;
+}
+
+static void __cpuinit mcpm_secondary_init(unsigned int cpu)
+{
+ mcpm_cpu_powered_up();
+ gic_secondary_init(0);
+}
+
+#ifdef CONFIG_HOTPLUG_CPU
+
+static int mcpm_cpu_disable(unsigned int cpu)
+{
+ /*
+ * We assume all CPUs may be shut down.
+ * This would be the hook to use for eventual Secure
+ * OS migration requests as described in the PSCI spec.
+ */
+ return 0;
+}
+
+static void mcpm_cpu_die(unsigned int cpu)
+{
+ unsigned int mpidr, pcpu, pcluster;
+ mpidr = read_cpuid_mpidr();
+ pcpu = MPIDR_AFFINITY_LEVEL(mpidr, 0);
+ pcluster = MPIDR_AFFINITY_LEVEL(mpidr, 1);
+ mcpm_set_entry_vector(pcpu, pcluster, NULL);
+ mcpm_cpu_power_down();
+}
+
+#endif
+
+struct smp_operations __initdata mcpm_smp_ops = {
+ .smp_init_cpus = simple_smp_init_cpus,
+ .smp_boot_secondary = mcpm_boot_secondary,
+ .smp_secondary_init = mcpm_secondary_init,
+#ifdef CONFIG_HOTPLUG_CPU
+ .cpu_disable = mcpm_cpu_disable,
+ .cpu_die = mcpm_cpu_die,
+#endif
+};
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 05/15] ARM: mcpm_head.S: vlock-based first man election
From: Nicolas Pitre @ 2013-01-29 7:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Dave Martin <dave.martin@linaro.org>
Instead of requiring the first man to be elected in advance (which
can be suboptimal in some situations), this patch uses a per-
cluster mutex to co-ordinate selection of the first man.
This should also make it more feasible to reuse this code path for
asynchronous cluster resume (as in CPUidle scenarios).
We must ensure that the vlock data doesn't share a cacheline with
anything else, or dirty cache eviction could corrupt it.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
---
arch/arm/common/Makefile | 2 +-
arch/arm/common/mcpm_head.S | 41 ++++++++++++++++++++++++++++++++++++-----
2 files changed, 37 insertions(+), 6 deletions(-)
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index 23e85b1fae..c901a38c59 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -13,4 +13,4 @@ obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
obj-$(CONFIG_SHARP_SCOOP) += scoop.o
obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o
obj-$(CONFIG_ARM_TIMER_SP804) += timer-sp.o
-obj-$(CONFIG_CLUSTER_PM) += mcpm_head.o mcpm_entry.o
+obj-$(CONFIG_CLUSTER_PM) += mcpm_head.o mcpm_entry.o vlock.o
diff --git a/arch/arm/common/mcpm_head.S b/arch/arm/common/mcpm_head.S
index 65db7ec87e..a2a2bb6bf0 100644
--- a/arch/arm/common/mcpm_head.S
+++ b/arch/arm/common/mcpm_head.S
@@ -16,6 +16,8 @@
#include <linux/linkage.h>
#include <asm/mcpm_entry.h>
+#include "vlock.h"
+
.if MCPM_SYNC_CLUSTER_CPUS
.error "cpus must be the first member of struct mcpm_sync_struct"
.endif
@@ -69,10 +71,11 @@ ENTRY(mcpm_entry_point)
* position independent way.
*/
adr r5, 3f
- ldmia r5, {r6, r7, r8}
+ ldmia r5, {r6, r7, r8, r11}
add r6, r5, r6 @ r6 = mcpm_entry_vectors
ldr r7, [r5, r7] @ r7 = mcpm_power_up_setup_phys
add r8, r5, r8 @ r8 = mcpm_sync
+ add r11, r5, r11 @ r11 = first_man_locks
mov r0, #MCPM_SYNC_CLUSTER_SIZE
mla r8, r0, r10, r8 @ r8 = sync cluster base
@@ -86,13 +89,22 @@ ENTRY(mcpm_entry_point)
@ At this point, the cluster cannot unexpectedly enter the GOING_DOWN
@ state, because there is at least one active CPU (this CPU).
- @ Note: the following is racy as another CPU might be testing
- @ the same flag at the same moment. That'll be fixed later.
+ mov r0, #VLOCK_SIZE
+ mla r11, r0, r10, r11 @ r11 = cluster first man lock
+ mov r0, r11
+ mov r1, r9 @ cpu
+ bl vlock_trylock @ implies DMB
+
+ cmp r0, #0 @ failed to get the lock?
+ bne mcpm_setup_wait @ wait for cluster setup if so
+
ldrb r0, [r8, #MCPM_SYNC_CLUSTER_CLUSTER]
cmp r0, #CLUSTER_UP @ cluster already up?
bne mcpm_setup @ if not, set up the cluster
- @ Otherwise, skip setup:
+ @ Otherwise, release the first man lock and skip setup:
+ mov r0, r11
+ bl vlock_unlock
b mcpm_setup_complete
mcpm_setup:
@@ -142,6 +154,19 @@ mcpm_setup_leave:
dsb
sev
+ mov r0, r11
+ bl vlock_unlock @ implies DMB
+ b mcpm_setup_complete
+
+ @ In the contended case, non-first men wait here for cluster setup
+ @ to complete:
+mcpm_setup_wait:
+ ldrb r0, [r8, #MCPM_SYNC_CLUSTER_CLUSTER]
+ cmp r0, #CLUSTER_UP
+ wfene
+ bne mcpm_setup_wait
+ dmb
+
mcpm_setup_complete:
@ If a platform-specific CPU setup hook is needed, it is
@ called from here.
@@ -173,11 +198,17 @@ mcpm_entry_gated:
3: .word mcpm_entry_vectors - .
.word mcpm_power_up_setup_phys - 3b
.word mcpm_sync - 3b
+ .word first_man_locks - 3b
ENDPROC(mcpm_entry_point)
.bss
- .align 5
+
+ .align __CACHE_WRITEBACK_ORDER
+ .type first_man_locks, #object
+first_man_locks:
+ .space VLOCK_SIZE * MAX_NR_CLUSTERS
+ .align __CACHE_WRITEBACK_ORDER
.type mcpm_entry_vectors, #object
ENTRY(mcpm_entry_vectors)
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 04/15] ARM: mcpm: Add baremetal voting mutexes
From: Nicolas Pitre @ 2013-01-29 7:50 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Dave Martin <dave.martin@linaro.org>
This patch adds a simple low-level voting mutex implementation
to be used to arbitrate during first man selection when no load/store
exclusive instructions are usable.
For want of a better name, these are called "vlocks". (I was
tempted to call them ballot locks, but "block" is way too confusing
an abbreviation...)
There is no function to wait for the lock to be released, and no
vlock_lock() function since we don't need these at the moment.
These could straightforwardly be added if vlocks get used for other
purposes.
For architectural correctness even Strongly-Ordered memory accesses
require barriers in order to guarantee that multiple CPUs have a
coherent view of the ordering of memory accesses. Whether or not
this matters depends on hardware implementation details of the
memory system. Since the purpose of this code is to provide a clean,
generic locking mechanism with no platform-specific dependencies the
barriers should be present to avoid unpleasant surprises on future
platforms.
Note:
* When taking the lock, we don't care about implicit background
memory operations and other signalling which may be pending,
because those are not part of the critical section anyway.
A DMB is sufficient to ensure correctly observed ordering if
the explicit memory accesses in vlock_trylock.
* No barrier is required after checking the election result,
because the result is determined by the store to
VLOCK_OWNER_OFFSET and is already globally observed due to the
barriers in voting_end. This means that global agreement on
the winner is guaranteed, even before the winner is known
locally.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Signed-off-by: Nicolas Pitre <nicolas.pitre@linaro.org>
---
Documentation/arm/vlocks.txt | 211 +++++++++++++++++++++++++++++++++++++++++++
arch/arm/common/vlock.S | 108 ++++++++++++++++++++++
arch/arm/common/vlock.h | 29 ++++++
3 files changed, 348 insertions(+)
create mode 100644 Documentation/arm/vlocks.txt
create mode 100644 arch/arm/common/vlock.S
create mode 100644 arch/arm/common/vlock.h
diff --git a/Documentation/arm/vlocks.txt b/Documentation/arm/vlocks.txt
new file mode 100644
index 0000000000..415960a9ba
--- /dev/null
+++ b/Documentation/arm/vlocks.txt
@@ -0,0 +1,211 @@
+vlocks for Bare-Metal Mutual Exclusion
+======================================
+
+Voting Locks, or "vlocks" provide a simple low-level mutual exclusion
+mechanism, with reasonable but minimal requirements on the memory
+system.
+
+These are intended to be used to coordinate critical activity among CPUs
+which are otherwise non-coherent, in situations where the hardware
+provides no other mechanism to support this and ordinary spinlocks
+cannot be used.
+
+
+vlocks make use of the atomicity provided by the memory system for
+writes to a single memory location. To arbitrate, every CPU "votes for
+itself", by storing a unique number to a common memory location. The
+final value seen in that memory location when all the votes have been
+cast identifies the winner.
+
+In order to make sure that the election produces an unambiguous result
+in finite time, a CPU will only enter the election in the first place if
+no winner has been chosen and the election does not appear to have
+started yet.
+
+
+Algorithm
+---------
+
+The easiest way to explain the vlocks algorithm is with some pseudo-code:
+
+
+ int currently_voting[NR_CPUS] = { 0, };
+ int last_vote = -1; /* no votes yet */
+
+ bool vlock_trylock(int this_cpu)
+ {
+ /* signal our desire to vote */
+ currently_voting[this_cpu] = 1;
+ if (last_vote != -1) {
+ /* someone already volunteered himself */
+ currently_voting[this_cpu] = 0;
+ return false; /* not ourself */
+ }
+
+ /* let's suggest ourself */
+ last_vote = this_cpu;
+ currently_voting[this_cpu] = 0;
+
+ /* then wait until everyone else is done voting */
+ for_each_cpu(i) {
+ while (currently_voting[i] != 0)
+ /* wait */;
+ }
+
+ /* result */
+ if (last_vote == this_cpu)
+ return true; /* we won */
+ return false;
+ }
+
+ bool vlock_unlock(void)
+ {
+ last_vote = -1;
+ }
+
+
+The currently_voting[] array provides a way for the CPUs to determine
+whether an election is in progress, and plays a role analogous to the
+"entering" array in Lamport's bakery algorithm [1].
+
+However, once the election has started, the underlying memory system
+atomicity is used to pick the winner. This avoids the need for a static
+priority rule to act as a tie-breaker, or any counters which could
+overflow.
+
+As long as the last_vote variable is globally visible to all CPUs, it
+will contain only one value that won't change once every CPU has cleared
+its currently_voting flag.
+
+
+Features and limitations
+------------------------
+
+ * vlocks are not intended to be fair. In the contended case, it is the
+ _last_ CPU which attempts to get the lock which will be most likely
+ to win.
+
+ vlocks are therefore best suited to situations where it is necessary
+ to pick a unique winner, but it does not matter which CPU actually
+ wins.
+
+ * Like other similar mechanisms, vlocks will not scale well to a large
+ number of CPUs.
+
+ vlocks can be cascaded in a voting hierarchy to permit better scaling
+ if necessary, as in the following hypothetical example for 4096 CPUs:
+
+ /* first level: local election */
+ my_town = towns[(this_cpu >> 4) & 0xf];
+ I_won = vlock_trylock(my_town, this_cpu & 0xf);
+ if (I_won) {
+ /* we won the town election, let's go for the state */
+ my_state = states[(this_cpu >> 8) & 0xf];
+ I_won = vlock_lock(my_state, this_cpu & 0xf));
+ if (I_won) {
+ /* and so on */
+ I_won = vlock_lock(the_whole_country, this_cpu & 0xf];
+ if (I_won) {
+ /* ... */
+ }
+ vlock_unlock(the_whole_country);
+ }
+ vlock_unlock(my_state);
+ }
+ vlock_unlock(my_town);
+
+
+ARM implementation
+------------------
+
+The current ARM implementation [2] contains some optimisations beyond
+the basic algorithm:
+
+ * By packing the members of the currently_voting array close together,
+ we can read the whole array in one transaction (providing the number
+ of CPUs potentially contending the lock is small enough). This
+ reduces the number of round-trips required to external memory.
+
+ In the ARM implementation, this means that we can use a single load
+ and comparison:
+
+ LDR Rt, [Rn]
+ CMP Rt, #0
+
+ ...in place of code equivalent to:
+
+ LDRB Rt, [Rn]
+ CMP Rt, #0
+ LDRBEQ Rt, [Rn, #1]
+ CMPEQ Rt, #0
+ LDRBEQ Rt, [Rn, #2]
+ CMPEQ Rt, #0
+ LDRBEQ Rt, [Rn, #3]
+ CMPEQ Rt, #0
+
+ This cuts down on the fast-path latency, as well as potentially
+ reducing bus contention in contended cases.
+
+ The optimisation relies on the fact that the ARM memory system
+ guarantees coherency between overlapping memory accesses of
+ different sizes, similarly to many other architectures. Note that
+ we do not care which element of currently_voting appears in which
+ bits of Rt, so there is no need to worry about endianness in this
+ optimisation.
+
+ If there are too many CPUs to read the currently_voting array in
+ one transaction then multiple transations are still required. The
+ implementation uses a simple loop of word-sized loads for this
+ case. The number of transactions is still fewer than would be
+ required if bytes were loaded individually.
+
+
+ In principle, we could aggregate further by using LDRD or LDM, but
+ to keep the code simple this was not attempted in the initial
+ implementation.
+
+
+ * vlocks are currently only used to coordinate between CPUs which are
+ unable to enable their caches yet. This means that the
+ implementation removes many of the barriers which would be required
+ when executing the algorithm in cached memory.
+
+ packing of the currently_voting array does not work with cached
+ memory unless all CPUs contending the lock are cache-coherent, due
+ to cache writebacks from one CPU clobbering values written by other
+ CPUs. (Though if all the CPUs are cache-coherent, you should be
+ probably be using proper spinlocks instead anyway).
+
+
+ * The "no votes yet" value used for the last_vote variable is 0 (not
+ -1 as in the pseudocode). This allows statically-allocated vlocks
+ to be implicitly initialised to an unlocked state simply by putting
+ them in .bss.
+
+ An offset is added to each CPU's ID for the purpose of setting this
+ variable, so that no CPU uses the value 0 for its ID.
+
+
+Colophon
+--------
+
+Originally created and documented by Dave Martin for Linaro Limited, for
+use in ARM-based big.LITTLE platforms, with review and input gratefully
+received from Nicolas Pitre and Achin Gupta. Thanks to Nicolas for
+grabbing most of this text out of the relevant mail thread and writing
+up the pseudocode.
+
+Copyright (C) 2012-2013 Linaro Limited
+Distributed under the terms of Version 2 of the GNU General Public
+License, as defined in linux/COPYING.
+
+
+References
+----------
+
+[1] Lamport, L. "A New Solution of Dijkstra's Concurrent Programming
+ Problem", Communications of the ACM 17, 8 (August 1974), 453-455.
+
+ http://en.wikipedia.org/wiki/Lamport%27s_bakery_algorithm
+
+[2] linux/arch/arm/common/vlock.S, www.kernel.org.
diff --git a/arch/arm/common/vlock.S b/arch/arm/common/vlock.S
new file mode 100644
index 0000000000..ff198583f6
--- /dev/null
+++ b/arch/arm/common/vlock.S
@@ -0,0 +1,108 @@
+/*
+ * vlock.S - simple voting lock implementation for ARM
+ *
+ * Created by: Dave Martin, 2012-08-16
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ *
+ * This algorithm is described in more detail in
+ * Documentation/arm/vlocks.txt.
+ */
+
+#include <linux/linkage.h>
+#include "vlock.h"
+
+/* Select different code if voting flags can fit in a single word. */
+#if VLOCK_VOTING_SIZE > 4
+#define FEW(x...)
+#define MANY(x...) x
+#else
+#define FEW(x...) x
+#define MANY(x...)
+#endif
+
+@ voting lock for first-man coordination
+
+.macro voting_begin rbase:req, rcpu:req, rscratch:req
+ mov \rscratch, #1
+ strb \rscratch, [\rbase, \rcpu]
+ dmb
+.endm
+
+.macro voting_end rbase:req, rcpu:req, rscratch:req
+ dmb
+ mov \rscratch, #0
+ strb \rscratch, [\rbase, \rcpu]
+ dsb
+ sev
+.endm
+
+/*
+ * The vlock structure must reside in Strongly-Ordered or Device memory.
+ * This implementation deliberately eliminates most of the barriers which
+ * would be required for other memory types, and assumes that independent
+ * writes to neighbouring locations within a cacheline do not interfere
+ * with one another.
+ */
+
+@ r0: lock structure base
+@ r1: CPU ID (0-based index within cluster)
+ENTRY(vlock_trylock)
+ add r1, r1, #VLOCK_VOTING_OFFSET
+
+ voting_begin r0, r1, r2
+
+ ldrb r2, [r0, #VLOCK_OWNER_OFFSET] @ check whether lock is held
+ cmp r2, #VLOCK_OWNER_NONE
+ bne trylock_fail @ fail if so
+
+ @ Control dependency implies strb not observable before previous ldrb.
+
+ strb r1, [r0, #VLOCK_OWNER_OFFSET] @ submit my vote
+
+ voting_end r0, r1, r2 @ implies DMB
+
+ @ Wait for the current round of voting to finish:
+
+ MANY( mov r3, #VLOCK_VOTING_OFFSET )
+0:
+ MANY( ldr r2, [r0, r3] )
+ FEW( ldr r2, [r0, #VLOCK_VOTING_OFFSET] )
+ cmp r2, #0
+ wfene
+ bne 0b
+ MANY( add r3, r3, #4 )
+ MANY( cmp r3, #VLOCK_VOTING_OFFSET + VLOCK_VOTING_SIZE )
+ MANY( bne 0b )
+
+ @ Check who won:
+
+ dmb
+ ldrb r2, [r0, #VLOCK_OWNER_OFFSET]
+ eor r0, r1, r2 @ zero if I won, else nonzero
+ bx lr
+
+trylock_fail:
+ voting_end r0, r1, r2
+ mov r0, #1 @ nonzero indicates that I lost
+ bx lr
+ENDPROC(vlock_trylock)
+
+@ r0: lock structure base
+ENTRY(vlock_unlock)
+ dmb
+ mov r1, #VLOCK_OWNER_NONE
+ strb r1, [r0, #VLOCK_OWNER_OFFSET]
+ dsb
+ sev
+ bx lr
+ENDPROC(vlock_unlock)
diff --git a/arch/arm/common/vlock.h b/arch/arm/common/vlock.h
new file mode 100644
index 0000000000..eda912f915
--- /dev/null
+++ b/arch/arm/common/vlock.h
@@ -0,0 +1,29 @@
+/*
+ * vlock.h - simple voting lock implementation
+ *
+ * Created by: Dave Martin, 2012-08-16
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __VLOCK_H
+#define __VLOCK_H
+
+#include <asm/mcpm_entry.h>
+
+/* Offsets and sizes are rounded to a word (4 bytes) */
+#define VLOCK_OWNER_OFFSET 0
+#define VLOCK_VOTING_OFFSET 4
+#define VLOCK_VOTING_SIZE ((MAX_CPUS_PER_CLUSTER + 3) / 4 * 4)
+#define VLOCK_SIZE (VLOCK_VOTING_OFFSET + VLOCK_VOTING_SIZE)
+#define VLOCK_OWNER_NONE 0
+
+#endif /* ! __VLOCK_H */
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 03/15] ARM: mcpm: introduce helpers for platform coherency exit/setup
From: Nicolas Pitre @ 2013-01-29 7:50 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
From: Dave Martin <dave.martin@linaro.org>
This provides helper methods to coordinate between CPUs coming down
and CPUs going up, as well as documentation on the used algorithms,
so that cluster teardown and setup
operations are not done for a cluster simultaneously.
For use in the power_down() implementation:
* __mcpm_cpu_going_down(unsigned int cluster, unsigned int cpu)
* __mcpm_outbound_enter_critical(unsigned int cluster)
* __mcpm_outbound_leave_critical(unsigned int cluster)
* __mcpm_cpu_down(unsigned int cluster, unsigned int cpu)
The power_up_setup() helper should do platform-specific setup in
preparation for turning the CPU on, such as invalidating local caches
or entering coherency. It must be assembler for now, since it must
run before the MMU can be switched on. It is passed the affinity level
which should be initialized.
Because the mcpm_sync_struct content is looked-up and modified
with the cache enabled or disabled depending on the code path, it is
crucial to always ensure proper cache maintenance to update main memory
right away. Therefore, any cached write must be followed by a cache
clean operation and any cached read must be preceded by a cache
invalidate operation (actually a cache flush i.e. clean+invalidate to
avoid discarding possible concurrent writes) on the accessed memory.
Also, in order to prevent a cached writer from interfering with an
adjacent non-cached writer, we ensure each state variable is located to
a separate cache line.
Thanks to Nicolas Pitre and Achin Gupta for the help with this
patch.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
---
Documentation/arm/cluster-pm-race-avoidance.txt | 498 ++++++++++++++++++++++++
arch/arm/common/mcpm_entry.c | 197 ++++++++++
arch/arm/common/mcpm_head.S | 106 ++++-
arch/arm/include/asm/mcpm_entry.h | 63 +++
4 files changed, 862 insertions(+), 2 deletions(-)
create mode 100644 Documentation/arm/cluster-pm-race-avoidance.txt
diff --git a/Documentation/arm/cluster-pm-race-avoidance.txt b/Documentation/arm/cluster-pm-race-avoidance.txt
new file mode 100644
index 0000000000..750b6fc24a
--- /dev/null
+++ b/Documentation/arm/cluster-pm-race-avoidance.txt
@@ -0,0 +1,498 @@
+Cluster-wide Power-up/power-down race avoidance algorithm
+=========================================================
+
+This file documents the algorithm which is used to coordinate CPU and
+cluster setup and teardown operations and to manage hardware coherency
+controls safely.
+
+The section "Rationale" explains what the algorithm is for and why it is
+needed. "Basic model" explains general concepts using a simplified view
+of the system. The other sections explain the actual details of the
+algorithm in use.
+
+
+Rationale
+---------
+
+In a system containing multiple CPUs, it is desirable to have the
+ability to turn off individual CPUs when the system is idle, reducing
+power consumption and thermal dissipation.
+
+In a system containing multiple clusters of CPUs, it is also desirable
+to have the ability to turn off entire clusters.
+
+Turning entire clusters off and on is a risky business, because it
+involves performing potentially destructive operations affecting a group
+of independently running CPUs, while the OS continues to run. This
+means that we need some coordination in order to ensure that critical
+cluster-level operations are only performed when it is truly safe to do
+so.
+
+Simple locking may not be sufficient to solve this problem, because
+mechanisms like Linux spinlocks may rely on coherency mechanisms which
+are not immediately enabled when a cluster powers up. Since enabling or
+disabling those mechanisms may itself be a non-atomic operation (such as
+writing some hardware registers and invalidating large caches), other
+methods of coordination are required in order to guarantee safe
+power-down and power-up at the cluster level.
+
+The mechanism presented in this document describes a coherent memory
+based protocol for performing the needed coordination. It aims to be as
+lightweight as possible, while providing the required safety properties.
+
+
+Basic model
+-----------
+
+Each cluster and CPU is assigned a state, as follows:
+
+ DOWN
+ COMING_UP
+ UP
+ GOING_DOWN
+
+ +---------> UP ----------+
+ | v
+
+ COMING_UP GOING_DOWN
+
+ ^ |
+ +--------- DOWN <--------+
+
+
+DOWN: The CPU or cluster is not coherent, and is either powered off or
+ suspended, or is ready to be powered off or suspended.
+
+COMING_UP: The CPU or cluster has committed to moving to the UP state.
+ It may be part way through the process of initialisation and
+ enabling coherency.
+
+UP: The CPU or cluster is active and coherent at the hardware
+ level. A CPU in this state is not necessarily being used
+ actively by the kernel.
+
+GOING_DOWN: The CPU or cluster has committed to moving to the DOWN
+ state. It may be part way through the process of teardown and
+ coherency exit.
+
+
+Each CPU has one of these states assigned to it at any point in time.
+The CPU states are described in the "CPU state" section, below.
+
+Each cluster is also assigned a state, but it is necessary to split the
+state value into two parts (the "cluster" state and "inbound" state) and
+to introduce additional states in order to avoid races between different
+CPUs in the cluster simultaneously modifying the state. The cluster-
+level states are described in the "Cluster state" section.
+
+To help distinguish the CPU states from cluster states in this
+discussion, the state names are given a CPU_ prefix for the CPU states,
+and a CLUSTER_ or INBOUND_ prefix for the cluster states.
+
+
+CPU state
+---------
+
+In this algorithm, each individual core in a multi-core processor is
+referred to as a "CPU". CPUs are assumed to be single-threaded:
+therefore, a CPU can only be doing one thing@a single point in time.
+
+This means that CPUs fit the basic model closely.
+
+The algorithm defines the following states for each CPU in the system:
+
+ CPU_DOWN
+ CPU_COMING_UP
+ CPU_UP
+ CPU_GOING_DOWN
+
+ cluster setup and
+ CPU setup complete policy decision
+ +-----------> CPU_UP ------------+
+ | v
+
+ CPU_COMING_UP CPU_GOING_DOWN
+
+ ^ |
+ +----------- CPU_DOWN <----------+
+ policy decision CPU teardown complete
+ or hardware event
+
+
+The definitions of the four states correspond closely to the states of
+the basic model.
+
+Transitions between states occur as follows.
+
+A trigger event (spontaneous) means that the CPU can transition to the
+next state as a result of making local progress only, with no
+requirement for any external event to happen.
+
+
+CPU_DOWN:
+
+ A CPU reaches the CPU_DOWN state when it is ready for
+ power-down. On reaching this state, the CPU will typically
+ power itself down or suspend itself, via a WFI instruction or a
+ firmware call.
+
+ Next state: CPU_COMING_UP
+ Conditions: none
+
+ Trigger events:
+
+ a) an explicit hardware power-up operation, resulting
+ from a policy decision on another CPU;
+
+ b) a hardware event, such as an interrupt.
+
+
+CPU_COMING_UP:
+
+ A CPU cannot start participating in hardware coherency until the
+ cluster is set up and coherent. If the cluster is not ready,
+ then the CPU will wait in the CPU_COMING_UP state until the
+ cluster has been set up.
+
+ Next state: CPU_UP
+ Conditions: The CPU's parent cluster must be in CLUSTER_UP.
+ Trigger events: Transition of the parent cluster to CLUSTER_UP.
+
+ Refer to the "Cluster state" section for a description of the
+ CLUSTER_UP state.
+
+
+CPU_UP:
+ When a CPU reaches the CPU_UP state, it is safe for the CPU to
+ start participating in local coherency.
+
+ This is done by jumping to the kernel's CPU resume code.
+
+ Note that the definition of this state is slightly different
+ from the basic model definition: CPU_UP does not mean that the
+ CPU is coherent yet, but it does mean that it is safe to resume
+ the kernel. The kernel handles the rest of the resume
+ procedure, so the remaining steps are not visible as part of the
+ race avoidance algorithm.
+
+ The CPU remains in this state until an explicit policy decision
+ is made to shut down or suspend the CPU.
+
+ Next state: CPU_GOING_DOWN
+ Conditions: none
+ Trigger events: explicit policy decision
+
+
+CPU_GOING_DOWN:
+
+ While in this state, the CPU exits coherency, including any
+ operations required to achieve this (such as cleaning data
+ caches).
+
+ Next state: CPU_DOWN
+ Conditions: local CPU teardown complete
+ Trigger events: (spontaneous)
+
+
+Cluster state
+-------------
+
+A cluster is a group of connected CPUs with some common resources.
+Because a cluster contains multiple CPUs, it can be doing multiple
+things@the same time. This has some implications. In particular, a
+CPU can start up while another CPU is tearing the cluster down.
+
+In this discussion, the "outbound side" is the view of the cluster state
+as seen by a CPU tearing the cluster down. The "inbound side" is the
+view of the cluster state as seen by a CPU setting the CPU up.
+
+In order to enable safe coordination in such situations, it is important
+that a CPU which is setting up the cluster can advertise its state
+independently of the CPU which is tearing down the cluster. For this
+reason, the cluster state is split into two parts:
+
+ "cluster" state: The global state of the cluster; or the state
+ on the outbound side:
+
+ CLUSTER_DOWN
+ CLUSTER_UP
+ CLUSTER_GOING_DOWN
+
+ "inbound" state: The state of the cluster on the inbound side.
+
+ INBOUND_NOT_COMING_UP
+ INBOUND_COMING_UP
+
+
+ The different pairings of these states results in six possible
+ states for the cluster as a whole:
+
+ CLUSTER_UP
+ +==========> INBOUND_NOT_COMING_UP -------------+
+ # |
+ |
+ CLUSTER_UP <----+ |
+ INBOUND_COMING_UP | v
+
+ ^ CLUSTER_GOING_DOWN CLUSTER_GOING_DOWN
+ # INBOUND_COMING_UP <=== INBOUND_NOT_COMING_UP
+
+ CLUSTER_DOWN | |
+ INBOUND_COMING_UP <----+ |
+ |
+ ^ |
+ +=========== CLUSTER_DOWN <------------+
+ INBOUND_NOT_COMING_UP
+
+ Transitions -----> can only be made by the outbound CPU, and
+ only involve changes to the "cluster" state.
+
+ Transitions ===##> can only be made by the inbound CPU, and only
+ involve changes to the "inbound" state, except where there is no
+ further transition possible on the outbound side (i.e., the
+ outbound CPU has put the cluster into the CLUSTER_DOWN state).
+
+ The race avoidance algorithm does not provide a way to determine
+ which exact CPUs within the cluster play these roles. This must
+ be decided in advance by some other means. Refer to the section
+ "Last man and first man selection" for more explanation.
+
+
+ CLUSTER_DOWN/INBOUND_NOT_COMING_UP is the only state where the
+ cluster can actually be powered down.
+
+ The parallelism of the inbound and outbound CPUs is observed by
+ the existence of two different paths from CLUSTER_GOING_DOWN/
+ INBOUND_NOT_COMING_UP (corresponding to GOING_DOWN in the basic
+ model) to CLUSTER_DOWN/INBOUND_COMING_UP (corresponding to
+ COMING_UP in the basic model). The second path avoids cluster
+ teardown completely.
+
+ CLUSTER_UP/INBOUND_COMING_UP is equivalent to UP in the basic
+ model. The final transition to CLUSTER_UP/INBOUND_NOT_COMING_UP
+ is trivial and merely resets the state machine ready for the
+ next cycle.
+
+ Details of the allowable transitions follow.
+
+ The next state in each case is notated
+
+ <cluster state>/<inbound state> (<transitioner>)
+
+ where the <transitioner> is the side on which the transition
+ can occur; either the inbound or the outbound side.
+
+
+CLUSTER_DOWN/INBOUND_NOT_COMING_UP:
+
+ Next state: CLUSTER_DOWN/INBOUND_COMING_UP (inbound)
+ Conditions: none
+ Trigger events:
+
+ a) an explicit hardware power-up operation, resulting
+ from a policy decision on another CPU;
+
+ b) a hardware event, such as an interrupt.
+
+
+CLUSTER_DOWN/INBOUND_COMING_UP:
+
+ In this state, an inbound CPU sets up the cluster, including
+ enabling of hardware coherency at the cluster level and any
+ other operations (such as cache invalidation) which are required
+ in order to achieve this.
+
+ The purpose of this state is to do sufficient cluster-level
+ setup to enable other CPUs in the cluster to enter coherency
+ safely.
+
+ Next state: CLUSTER_UP/INBOUND_COMING_UP (inbound)
+ Conditions: cluster-level setup and hardware coherency complete
+ Trigger events: (spontaneous)
+
+
+CLUSTER_UP/INBOUND_COMING_UP:
+
+ Cluster-level setup is complete and hardware coherency is
+ enabled for the cluster. Other CPUs in the cluster can safely
+ enter coherency.
+
+ This is a transient state, leading immediately to
+ CLUSTER_UP/INBOUND_NOT_COMING_UP. All other CPUs on the cluster
+ should consider treat these two states as equivalent.
+
+ Next state: CLUSTER_UP/INBOUND_NOT_COMING_UP (inbound)
+ Conditions: none
+ Trigger events: (spontaneous)
+
+
+CLUSTER_UP/INBOUND_NOT_COMING_UP:
+
+ Cluster-level setup is complete and hardware coherency is
+ enabled for the cluster. Other CPUs in the cluster can safely
+ enter coherency.
+
+ The cluster will remain in this state until a policy decision is
+ made to power the cluster down.
+
+ Next state: CLUSTER_GOING_DOWN/INBOUND_NOT_COMING_UP (outbound)
+ Conditions: none
+ Trigger events: policy decision to power down the cluster
+
+
+CLUSTER_GOING_DOWN/INBOUND_NOT_COMING_UP:
+
+ An outbound CPU is tearing the cluster down. The selected CPU
+ must wait in this state until all CPUs in the cluster are in the
+ CPU_DOWN state.
+
+ When all CPUs are in the CPU_DOWN state, the cluster can be torn
+ down, for example by cleaning data caches and exiting
+ cluster-level coherency.
+
+ To avoid wasteful unnecessary teardown operations, the outbound
+ should check the inbound cluster state for asynchronous
+ transitions to INBOUND_COMING_UP. Alternatively, individual
+ CPUs can be checked for entry into CPU_COMING_UP or CPU_UP.
+
+
+ Next states:
+
+ CLUSTER_DOWN/INBOUND_NOT_COMING_UP (outbound)
+ Conditions: cluster torn down and ready to power off
+ Trigger events: (spontaneous)
+
+ CLUSTER_GOING_DOWN/INBOUND_COMING_UP (inbound)
+ Conditions: none
+ Trigger events:
+
+ a) an explicit hardware power-up operation,
+ resulting from a policy decision on another
+ CPU;
+
+ b) a hardware event, such as an interrupt.
+
+
+CLUSTER_GOING_DOWN/INBOUND_COMING_UP:
+
+ The cluster is (or was) being torn down, but another CPU has
+ come online in the meantime and is trying to set up the cluster
+ again.
+
+ If the outbound CPU observes this state, it has two choices:
+
+ a) back out of teardown, restoring the cluster to the
+ CLUSTER_UP state;
+
+ b) finish tearing the cluster down and put the cluster
+ in the CLUSTER_DOWN state; the inbound CPU will
+ set up the cluster again from there.
+
+ Choice (a) permits the removal of some latency by avoiding
+ unnecessary teardown and setup operations in situations where
+ the cluster is not really going to be powered down.
+
+
+ Next states:
+
+ CLUSTER_UP/INBOUND_COMING_UP (outbound)
+ Conditions: cluster-level setup and hardware
+ coherency complete
+ Trigger events: (spontaneous)
+
+ CLUSTER_DOWN/INBOUND_COMING_UP (outbound)
+ Conditions: cluster torn down and ready to power off
+ Trigger events: (spontaneous)
+
+
+Last man and First man selection
+--------------------------------
+
+The CPU which performs cluster tear-down operations on the outbound side
+is commonly referred to as the "last man".
+
+The CPU which performs cluster setup on the inbound side is commonly
+referred to as the "first man".
+
+The race avoidance algorithm documented above does not provide a
+mechanism to choose which CPUs should play these roles.
+
+
+Last man:
+
+When shutting down the cluster, all the CPUs involved are initially
+executing Linux and hence coherent. Therefore, ordinary spinlocks can
+be used to select a last man safely, before the CPUs become
+non-coherent.
+
+
+First man:
+
+Because CPUs may power up asynchronously in response to external wake-up
+events, a dynamic mechanism is needed to make sure that only one CPU
+attempts to play the first man role and do the cluster-level
+initialisation: any other CPUs must wait for this to complete before
+proceeding.
+
+Cluster-level initialisation may involve actions such as configuring
+coherency controls in the bus fabric.
+
+The current implementation in mcpm_head.S uses a separate mutual exclusion
+mechanism to do this arbitration. This mechanism is documented in
+detail in vlocks.txt.
+
+
+Features and Limitations
+------------------------
+
+Implementation:
+
+ The current ARM-based implementation is split between
+ arch/arm/common/mcpm_head.S (low-level inbound CPU operations) and
+ arch/arm/common/mcpm_entry.c (everything else):
+
+ __mcpm_cpu_going_down() signals the transition of a CPU to the
+ CPU_GOING_DOWN state.
+
+ __mcpm_cpu_down() signals the transition of a CPU to the CPU_DOWN
+ state.
+
+ A CPU transitions to CPU_COMING_UP and then to CPU_UP via the
+ low-level power-up code in mcpm_head.S. This could
+ involve CPU-specific setup code, but in the current
+ implementation it does not.
+
+ __mcpm_outbound_enter_critical() and __mcpm_outbound_leave_critical()
+ handle transitions from CLUSTER_UP to CLUSTER_GOING_DOWN
+ and from there to CLUSTER_DOWN or back to CLUSTER_UP (in
+ the case of an aborted cluster power-down).
+
+ These functions are more complex than the __mcpm_cpu_*()
+ functions due to the extra inter-CPU coordination which
+ is needed for safe transitions at the cluster level.
+
+ A cluster transitions from CLUSTER_DOWN back to CLUSTER_UP via
+ the low-level power-up code in mcpm_head.S. This
+ typically involves platform-specific setup code,
+ provided by the platform-specific power_up_setup
+ function registered via mcpm_sync_init.
+
+Deep topologies:
+
+ As currently described and implemented, the algorithm does not
+ support CPU topologies involving more than two levels (i.e.,
+ clusters of clusters are not supported). The algorithm could be
+ extended by replicating the cluster-level states for the
+ additional topological levels, and modifying the transition
+ rules for the intermediate (non-outermost) cluster levels.
+
+
+Colophon
+--------
+
+Originally created and documented by Dave Martin for Linaro Limited, in
+collaboration with Nicolas Pitre and Achin Gupta.
+
+Copyright (C) 2012-2013 Linaro Limited
+Distributed under the terms of Version 2 of the GNU General Public
+License, as defined in linux/COPYING.
diff --git a/arch/arm/common/mcpm_entry.c b/arch/arm/common/mcpm_entry.c
index c8c0e2113e..2b83121966 100644
--- a/arch/arm/common/mcpm_entry.c
+++ b/arch/arm/common/mcpm_entry.c
@@ -18,6 +18,7 @@
#include <asm/proc-fns.h>
#include <asm/cacheflush.h>
#include <asm/idmap.h>
+#include <asm/cputype.h>
extern volatile unsigned long mcpm_entry_vectors[MAX_NR_CLUSTERS][MAX_CPUS_PER_CLUSTER];
@@ -115,3 +116,199 @@ int mcpm_cpu_powered_up(void)
platform_ops->powered_up();
return 0;
}
+
+struct sync_struct mcpm_sync;
+
+/*
+ * There is no __cpuc_clean_dcache_area but we use it anyway for
+ * code intent clarity, and alias it to __cpuc_flush_dcache_area.
+ */
+#define __cpuc_clean_dcache_area __cpuc_flush_dcache_area
+
+/*
+ * Ensure preceding writes to *p by this CPU are visible to
+ * subsequent reads by other CPUs:
+ */
+static void __sync_range_w(volatile void *p, size_t size)
+{
+ char *_p = (char *)p;
+
+ __cpuc_clean_dcache_area(_p, size);
+ outer_clean_range(__pa(_p), __pa(_p + size));
+}
+
+/*
+ * Ensure preceding writes to *p by other CPUs are visible to
+ * subsequent reads by this CPU. We must be careful not to
+ * discard data simultaneously written by another CPU, hence the
+ * usage of flush rather than invalidate operations.
+ */
+static void __sync_range_r(volatile void *p, size_t size)
+{
+ char *_p = (char *)p;
+
+#ifdef CONFIG_OUTER_CACHE
+ if (outer_cache.flush_range) {
+ /*
+ * Ensure dirty data migrated from other CPUs into our cache
+ * are cleaned out safely before the outer cache is cleaned:
+ */
+ __cpuc_clean_dcache_area(_p, size);
+
+ /* Clean and invalidate stale data for *p from outer ... */
+ outer_flush_range(__pa(_p), __pa(_p + size));
+ }
+#endif
+
+ /* ... and inner cache: */
+ __cpuc_flush_dcache_area(_p, size);
+}
+
+#define sync_w(ptr) __sync_range_w(ptr, sizeof *(ptr))
+#define sync_r(ptr) __sync_range_r(ptr, sizeof *(ptr))
+
+/*
+ * __mcpm_cpu_going_down: Indicates that the cpu is being torn down.
+ * This must be called at the point of committing to teardown of a CPU.
+ * The CPU cache (SCTRL.C bit) is expected to still be active.
+ */
+void __mcpm_cpu_going_down(unsigned int cpu, unsigned int cluster)
+{
+ mcpm_sync.clusters[cluster].cpus[cpu].cpu = CPU_GOING_DOWN;
+ sync_w(&mcpm_sync.clusters[cluster].cpus[cpu].cpu);
+}
+
+/*
+ * __mcpm_cpu_down: Indicates that cpu teardown is complete and that the
+ * cluster can be torn down without disrupting this CPU.
+ * To avoid deadlocks, this must be called before a CPU is powered down.
+ * The CPU cache (SCTRL.C bit) is expected to be off.
+ */
+void __mcpm_cpu_down(unsigned int cpu, unsigned int cluster)
+{
+ dmb();
+ mcpm_sync.clusters[cluster].cpus[cpu].cpu = CPU_DOWN;
+ sync_w(&mcpm_sync.clusters[cluster].cpus[cpu].cpu);
+ dsb_sev();
+}
+
+/*
+ * __mcpm_outbound_leave_critical: Leave the cluster teardown critical section.
+ * @state: the final state of the cluster:
+ * CLUSTER_UP: no destructive teardown was done and the cluster has been
+ * restored to the previous state (CPU cache still active); or
+ * CLUSTER_DOWN: the cluster has been torn-down, ready for power-off
+ * (CPU cache disabled).
+ */
+void __mcpm_outbound_leave_critical(unsigned int cluster, int state)
+{
+ dmb();
+ mcpm_sync.clusters[cluster].cluster = state;
+ sync_w(&mcpm_sync.clusters[cluster].cluster);
+ dsb_sev();
+}
+
+/*
+ * __mcpm_outbound_enter_critical: Enter the cluster teardown critical section.
+ * This function should be called by the last man, after local CPU teardown
+ * is complete. CPU cache expected to be active.
+ *
+ * Returns:
+ * false: the critical section was not entered because an inbound CPU was
+ * observed, or the cluster is already being set up;
+ * true: the critical section was entered: it is now safe to tear down the
+ * cluster.
+ */
+bool __mcpm_outbound_enter_critical(unsigned int cpu, unsigned int cluster)
+{
+ unsigned int i;
+ struct mcpm_sync_struct *c = &mcpm_sync.clusters[cluster];
+
+ /* Warn inbound CPUs that the cluster is being torn down: */
+ c->cluster = CLUSTER_GOING_DOWN;
+ sync_w(&c->cluster);
+
+ /* Back out if the inbound cluster is already in the critical region: */
+ sync_r(&c->inbound);
+ if (c->inbound == INBOUND_COMING_UP)
+ goto abort;
+
+ /*
+ * Wait for all CPUs to get out of the GOING_DOWN state, so that local
+ * teardown is complete on each CPU before tearing down the cluster.
+ *
+ * If any CPU has been woken up again from the DOWN state, then we
+ * shouldn't be taking the cluster down at all: abort in that case.
+ */
+ sync_r(&c->cpus);
+ for (i = 0; i < MAX_CPUS_PER_CLUSTER; i++) {
+ int cpustate;
+
+ if (i == cpu)
+ continue;
+
+ while (1) {
+ cpustate = c->cpus[i].cpu;
+ if (cpustate != CPU_GOING_DOWN)
+ break;
+
+ wfe();
+ sync_r(&c->cpus[i].cpu);
+ }
+
+ switch (cpustate) {
+ case CPU_DOWN:
+ continue;
+
+ default:
+ goto abort;
+ }
+ }
+
+ return true;
+
+abort:
+ __mcpm_outbound_leave_critical(cluster, CLUSTER_UP);
+ return false;
+}
+
+int __mcpm_mcpm_state(unsigned int cluster)
+{
+ sync_r(&mcpm_sync.clusters[cluster].cluster);
+ return mcpm_sync.clusters[cluster].cluster;
+}
+
+extern unsigned long mcpm_power_up_setup_phys;
+
+int __init mcpm_sync_init(
+ void (*power_up_setup)(unsigned int affinity_level))
+{
+ unsigned int i, j, mpidr, this_cluster;
+
+ BUILD_BUG_ON(MCPM_SYNC_CLUSTER_SIZE * MAX_NR_CLUSTERS != sizeof mcpm_sync);
+ BUG_ON((unsigned long)&mcpm_sync & (__CACHE_WRITEBACK_GRANULE - 1));
+
+ /*
+ * Set initial CPU and cluster states.
+ * Only one cluster is assumed to be active at this point.
+ */
+ for (i = 0; i < MAX_NR_CLUSTERS; i++) {
+ mcpm_sync.clusters[i].cluster = CLUSTER_DOWN;
+ mcpm_sync.clusters[i].inbound = INBOUND_NOT_COMING_UP;
+ for (j = 0; j < MAX_CPUS_PER_CLUSTER; j++)
+ mcpm_sync.clusters[i].cpus[j].cpu = CPU_DOWN;
+ }
+ mpidr = read_cpuid_mpidr();
+ this_cluster = MPIDR_AFFINITY_LEVEL(mpidr, 1);
+ for_each_online_cpu(i)
+ mcpm_sync.clusters[this_cluster].cpus[i].cpu = CPU_UP;
+ mcpm_sync.clusters[this_cluster].cluster = CLUSTER_UP;
+ sync_w(&mcpm_sync);
+
+ if (power_up_setup) {
+ mcpm_power_up_setup_phys = virt_to_phys(power_up_setup);
+ sync_w(&mcpm_power_up_setup_phys);
+ }
+
+ return 0;
+}
diff --git a/arch/arm/common/mcpm_head.S b/arch/arm/common/mcpm_head.S
index 794c8ea8c4..65db7ec87e 100644
--- a/arch/arm/common/mcpm_head.S
+++ b/arch/arm/common/mcpm_head.S
@@ -7,11 +7,19 @@
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
+ *
+ *
+ * Refer to Documentation/arm/cluster-pm-race-avoidance.txt
+ * for details of the synchronisation algorithms used here.
*/
#include <linux/linkage.h>
#include <asm/mcpm_entry.h>
+.if MCPM_SYNC_CLUSTER_CPUS
+.error "cpus must be the first member of struct mcpm_sync_struct"
+.endif
+
.macro pr_dbg string
#if defined(CONFIG_DEBUG_LL) && defined(DEBUG)
b 1901f
@@ -57,24 +65,114 @@ ENTRY(mcpm_entry_point)
2: pr_dbg "kernel mcpm_entry_point\n"
/*
- * MMU is off so we need to get to mcpm_entry_vectors in a
+ * MMU is off so we need to get to various variables in a
* position independent way.
*/
adr r5, 3f
- ldr r6, [r5]
+ ldmia r5, {r6, r7, r8}
add r6, r5, r6 @ r6 = mcpm_entry_vectors
+ ldr r7, [r5, r7] @ r7 = mcpm_power_up_setup_phys
+ add r8, r5, r8 @ r8 = mcpm_sync
+
+ mov r0, #MCPM_SYNC_CLUSTER_SIZE
+ mla r8, r0, r10, r8 @ r8 = sync cluster base
+
+ @ Signal that this CPU is coming UP:
+ mov r0, #CPU_COMING_UP
+ mov r5, #MCPM_SYNC_CPU_SIZE
+ mla r5, r9, r5, r8 @ r5 = sync cpu address
+ strb r0, [r5]
+
+ @ At this point, the cluster cannot unexpectedly enter the GOING_DOWN
+ @ state, because there is at least one active CPU (this CPU).
+
+ @ Note: the following is racy as another CPU might be testing
+ @ the same flag at the same moment. That'll be fixed later.
+ ldrb r0, [r8, #MCPM_SYNC_CLUSTER_CLUSTER]
+ cmp r0, #CLUSTER_UP @ cluster already up?
+ bne mcpm_setup @ if not, set up the cluster
+
+ @ Otherwise, skip setup:
+ b mcpm_setup_complete
+
+mcpm_setup:
+ @ Control dependency implies strb not observable before previous ldrb.
+
+ @ Signal that the cluster is being brought up:
+ mov r0, #INBOUND_COMING_UP
+ strb r0, [r8, #MCPM_SYNC_CLUSTER_INBOUND]
+ dmb
+
+ @ Any CPU trying to take the cluster into CLUSTER_GOING_DOWN from this
+ @ point onwards will observe INBOUND_COMING_UP and abort.
+
+ @ Wait for any previously-pending cluster teardown operations to abort
+ @ or complete:
+mcpm_teardown_wait:
+ ldrb r0, [r8, #MCPM_SYNC_CLUSTER_CLUSTER]
+ cmp r0, #CLUSTER_GOING_DOWN
+ bne first_man_setup
+ wfe
+ b mcpm_teardown_wait
+
+first_man_setup:
+ dmb
+
+ @ If the outbound gave up before teardown started, skip cluster setup:
+
+ cmp r0, #CLUSTER_UP
+ beq mcpm_setup_leave
+
+ @ power_up_setup is now responsible for setting up the cluster:
+
+ cmp r7, #0
+ mov r0, #1 @ second (cluster) affinity level
+ blxne r7 @ Call power_up_setup if defined
+ dmb
+
+ mov r0, #CLUSTER_UP
+ strb r0, [r8, #MCPM_SYNC_CLUSTER_CLUSTER]
+ dmb
+
+mcpm_setup_leave:
+ @ Leave the cluster setup critical section:
+
+ mov r0, #INBOUND_NOT_COMING_UP
+ strb r0, [r8, #MCPM_SYNC_CLUSTER_INBOUND]
+ dsb
+ sev
+
+mcpm_setup_complete:
+ @ If a platform-specific CPU setup hook is needed, it is
+ @ called from here.
+
+ cmp r7, #0
+ mov r0, #0 @ first (CPU) affinity level
+ blxne r7 @ Call power_up_setup if defined
+ dmb
+
+ @ Mark the CPU as up:
+
+ mov r0, #CPU_UP
+ strb r0, [r5]
+
+ @ Observability order of CPU_UP and opening of the gate does not matter.
mcpm_entry_gated:
ldr r5, [r6, r4, lsl #2] @ r5 = CPU entry vector
cmp r5, #0
wfeeq
beq mcpm_entry_gated
+ dmb
+
pr_dbg "released\n"
bx r5
.align 2
3: .word mcpm_entry_vectors - .
+ .word mcpm_power_up_setup_phys - 3b
+ .word mcpm_sync - 3b
ENDPROC(mcpm_entry_point)
@@ -84,3 +182,7 @@ ENDPROC(mcpm_entry_point)
.type mcpm_entry_vectors, #object
ENTRY(mcpm_entry_vectors)
.space 4 * MAX_NR_CLUSTERS * MAX_CPUS_PER_CLUSTER
+
+ .type mcpm_power_up_setup_phys, #object
+ENTRY(mcpm_power_up_setup_phys)
+ .space 4 @ set by mcpm_sync_init()
diff --git a/arch/arm/include/asm/mcpm_entry.h b/arch/arm/include/asm/mcpm_entry.h
index 3286d5eb91..e76652209d 100644
--- a/arch/arm/include/asm/mcpm_entry.h
+++ b/arch/arm/include/asm/mcpm_entry.h
@@ -15,8 +15,37 @@
#define MAX_CPUS_PER_CLUSTER 4
#define MAX_NR_CLUSTERS 2
+/* Definitions for mcpm_sync_struct */
+#define CPU_DOWN 0x11
+#define CPU_COMING_UP 0x12
+#define CPU_UP 0x13
+#define CPU_GOING_DOWN 0x14
+
+#define CLUSTER_DOWN 0x21
+#define CLUSTER_UP 0x22
+#define CLUSTER_GOING_DOWN 0x23
+
+#define INBOUND_NOT_COMING_UP 0x31
+#define INBOUND_COMING_UP 0x32
+
+/* This is a complete guess. */
+#define __CACHE_WRITEBACK_ORDER 6
+#define __CACHE_WRITEBACK_GRANULE (1 << __CACHE_WRITEBACK_ORDER)
+
+/* Offsets for the mcpm_sync_struct members, for use in asm: */
+#define MCPM_SYNC_CLUSTER_CPUS 0
+#define MCPM_SYNC_CPU_SIZE __CACHE_WRITEBACK_GRANULE
+#define MCPM_SYNC_CLUSTER_CLUSTER \
+ (MCPM_SYNC_CLUSTER_CPUS + MCPM_SYNC_CPU_SIZE * MAX_CPUS_PER_CLUSTER)
+#define MCPM_SYNC_CLUSTER_INBOUND \
+ (MCPM_SYNC_CLUSTER_CLUSTER + __CACHE_WRITEBACK_GRANULE)
+#define MCPM_SYNC_CLUSTER_SIZE \
+ (MCPM_SYNC_CLUSTER_INBOUND + __CACHE_WRITEBACK_GRANULE)
+
#ifndef __ASSEMBLY__
+#include <linux/types.h>
+
/*
* Platform specific code should use this symbol to set up secondary
* entry location for processors to use when released from reset.
@@ -123,5 +152,39 @@ struct mcpm_platform_ops {
*/
int __init mcpm_platform_register(const struct mcpm_platform_ops *ops);
+/* Synchronisation structures for coordinating safe cluster setup/teardown: */
+
+/*
+ * When modifying this structure, make sure you update the MCPM_SYNC_ defines
+ * to match.
+ */
+struct mcpm_sync_struct {
+ /* individual CPU states */
+ struct {
+ volatile s8 cpu __aligned(__CACHE_WRITEBACK_GRANULE);
+ } cpus[MAX_CPUS_PER_CLUSTER];
+
+ /* cluster state */
+ volatile s8 cluster __aligned(__CACHE_WRITEBACK_GRANULE);
+
+ /* inbound-side state */
+ volatile s8 inbound __aligned(__CACHE_WRITEBACK_GRANULE);
+};
+
+struct sync_struct {
+ struct mcpm_sync_struct clusters[MAX_NR_CLUSTERS];
+};
+
+extern unsigned long sync_phys; /* physical address of *mcpm_sync */
+
+void __mcpm_cpu_going_down(unsigned int cpu, unsigned int cluster);
+void __mcpm_cpu_down(unsigned int cpu, unsigned int cluster);
+void __mcpm_outbound_leave_critical(unsigned int cluster, int state);
+bool __mcpm_outbound_enter_critical(unsigned int this_cpu, unsigned int cluster);
+int __mcpm_mcpm_state(unsigned int cluster);
+
+int __init mcpm_sync_init(
+ void (*power_up_setup)(unsigned int affinity_level));
+
#endif /* ! __ASSEMBLY__ */
#endif
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 02/15] ARM: mcpm: introduce the CPU/cluster power API
From: Nicolas Pitre @ 2013-01-29 7:50 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
This is the basic API used to handle the powering up/down of individual
CPUs in a (multi-)cluster system. The platform specific backend
implementation has the responsibility to also handle the cluster level
power as well when the first/last CPU in a cluster is brought up/down.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/common/mcpm_entry.c | 88 +++++++++++++++++++++++++++++++++++++
arch/arm/include/asm/mcpm_entry.h | 92 +++++++++++++++++++++++++++++++++++++++
2 files changed, 180 insertions(+)
diff --git a/arch/arm/common/mcpm_entry.c b/arch/arm/common/mcpm_entry.c
index 3a6d7e70fd..c8c0e2113e 100644
--- a/arch/arm/common/mcpm_entry.c
+++ b/arch/arm/common/mcpm_entry.c
@@ -11,11 +11,13 @@
#include <linux/kernel.h>
#include <linux/init.h>
+#include <linux/irqflags.h>
#include <asm/mcpm_entry.h>
#include <asm/barrier.h>
#include <asm/proc-fns.h>
#include <asm/cacheflush.h>
+#include <asm/idmap.h>
extern volatile unsigned long mcpm_entry_vectors[MAX_NR_CLUSTERS][MAX_CPUS_PER_CLUSTER];
@@ -27,3 +29,89 @@ void mcpm_set_entry_vector(unsigned cpu, unsigned cluster, void *ptr)
outer_clean_range(__pa(&mcpm_entry_vectors[cluster][cpu]),
__pa(&mcpm_entry_vectors[cluster][cpu + 1]));
}
+
+static const struct mcpm_platform_ops *platform_ops;
+
+int __init mcpm_platform_register(const struct mcpm_platform_ops *ops)
+{
+ if (platform_ops)
+ return -EBUSY;
+ platform_ops = ops;
+ return 0;
+}
+
+int mcpm_cpu_power_up(unsigned int cpu, unsigned int cluster)
+{
+ if (!platform_ops)
+ return -EUNATCH; /* try not to shadow power_up errors */
+ might_sleep();
+ return platform_ops->power_up(cpu, cluster);
+}
+
+typedef void (*phys_reset_t)(unsigned long);
+
+void mcpm_cpu_power_down(void)
+{
+ phys_reset_t phys_reset;
+
+ BUG_ON(!platform_ops);
+ BUG_ON(!irqs_disabled());
+
+ /*
+ * Do this before calling into the power_down method,
+ * as it might not always be safe to do afterwards.
+ */
+ setup_mm_for_reboot();
+
+ platform_ops->power_down();
+
+ /*
+ * It is possible for a power_up request to happen concurrently
+ * with a power_down request for the same CPU. In this case the
+ * power_down method might not be able to actually enter a
+ * powered down state with the WFI instruction if the power_up
+ * method has removed the required reset condition. The
+ * power_down method is then allowed to return. We must perform
+ * a re-entry in the kernel as if the power_up method just had
+ * deasserted reset on the CPU.
+ *
+ * To simplify race issues, the platform specific implementation
+ * must accommodate for the possibility of unordered calls to
+ * power_down and power_up with a usage count. Therefore, if a
+ * call to power_up is issued for a CPU that is not down, then
+ * the next call to power_down must not attempt a full shutdown
+ * but only do the minimum (normally disabling L1 cache and CPU
+ * coherency) and return just as if a concurrent power_up request
+ * had happened as described above.
+ */
+
+ phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset);
+ phys_reset(virt_to_phys(mcpm_entry_point));
+
+ /* should never get here */
+ BUG();
+}
+
+void mcpm_cpu_suspend(u64 expected_residency)
+{
+ phys_reset_t phys_reset;
+
+ BUG_ON(!platform_ops);
+ BUG_ON(!irqs_disabled());
+
+ /* Very similar to mcpm_cpu_power_down() */
+ setup_mm_for_reboot();
+ platform_ops->suspend(expected_residency);
+ phys_reset = (phys_reset_t)(unsigned long)virt_to_phys(cpu_reset);
+ phys_reset(virt_to_phys(mcpm_entry_point));
+ BUG();
+}
+
+int mcpm_cpu_powered_up(void)
+{
+ if (!platform_ops)
+ return -EUNATCH;
+ if (platform_ops->powered_up)
+ platform_ops->powered_up();
+ return 0;
+}
diff --git a/arch/arm/include/asm/mcpm_entry.h b/arch/arm/include/asm/mcpm_entry.h
index cc10ebbd2e..3286d5eb91 100644
--- a/arch/arm/include/asm/mcpm_entry.h
+++ b/arch/arm/include/asm/mcpm_entry.h
@@ -31,5 +31,97 @@ extern void mcpm_entry_point(void);
*/
void mcpm_set_entry_vector(unsigned cpu, unsigned cluster, void *ptr);
+/*
+ * CPU/cluster power operations API for higher subsystems to use.
+ */
+
+/**
+ * mcpm_cpu_power_up - make given CPU in given cluster runable
+ *
+ * @cpu: CPU number within given cluster
+ * @cluster: cluster number for the CPU
+ *
+ * The identified CPU is brought out of reset. If the cluster was powered
+ * down then it is brought up as well, taking care not to let the other CPUs
+ * in the cluster run, and ensuring appropriate cluster setup.
+ *
+ * Caller must ensure the appropriate entry vector is initialized with
+ * mcpm_set_entry_vector() prior to calling this.
+ *
+ * This must be called in a sleepable context. However, the implementation
+ * is strongly encouraged to return early and let the operation happen
+ * asynchronously, especially when significant delays are expected.
+ *
+ * If the operation cannot be performed then an error code is returned.
+ */
+int mcpm_cpu_power_up(unsigned int cpu, unsigned int cluster);
+
+/**
+ * mcpm_cpu_power_down - power the calling CPU down
+ *
+ * The calling CPU is powered down.
+ *
+ * If this CPU is found to be the "last man standing" in the cluster
+ * then the cluster is prepared for power-down too.
+ *
+ * This must be called with interrupts disabled.
+ *
+ * This does not return. Re-entry in the kernel is expected via
+ * mcpm_entry_point.
+ */
+void mcpm_cpu_power_down(void);
+
+/**
+ * mcpm_cpu_suspend - bring the calling CPU in a suspended state
+ *
+ * @expected_residency: duration in microseconds the CPU is expected
+ * to remain suspended, or 0 if unknown/infinity.
+ *
+ * The calling CPU is suspended. The expected residency argument is used
+ * as a hint by the platform specific backend to implement the appropriate
+ * sleep state level according to the knowledge it has on wake-up latency
+ * for the given hardware.
+ *
+ * If this CPU is found to be the "last man standing" in the cluster
+ * then the cluster may be prepared for power-down too, if the expected
+ * residency makes it worthwhile.
+ *
+ * This must be called with interrupts disabled.
+ *
+ * This does not return. Re-entry in the kernel is expected via
+ * mcpm_entry_point.
+ */
+void mcpm_cpu_suspend(u64 expected_residency);
+
+/**
+ * mcpm_cpu_powered_up - housekeeping workafter a CPU has been powered up
+ *
+ * This lets the platform specific backend code perform needed housekeeping
+ * work. This must be called by the newly activated CPU as soon as it is
+ * fully operational in kernel space, before it enables interrupts.
+ *
+ * If the operation cannot be performed then an error code is returned.
+ */
+int mcpm_cpu_powered_up(void);
+
+/*
+ * Platform specific methods used in the implementation of the above API.
+ */
+struct mcpm_platform_ops {
+ int (*power_up)(unsigned int cpu, unsigned int cluster);
+ void (*power_down)(void);
+ void (*suspend)(u64);
+ void (*powered_up)(void);
+};
+
+/**
+ * mcpm_platform_register - register platform specific power methods
+ *
+ * @ops: mcpm_platform_ops structure to register
+ *
+ * An error is returned if the registration has been done previously.
+ */
+int __init mcpm_platform_register(const struct mcpm_platform_ops *ops);
+
#endif /* ! __ASSEMBLY__ */
#endif
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 01/15] ARM: multi-cluster PM: secondary kernel entry code
From: Nicolas Pitre @ 2013-01-29 7:50 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445870-18925-1-git-send-email-nicolas.pitre@linaro.org>
CPUs in cluster based systems, such as big.LITTLE, have special needs
when entering the kernel due to a hotplug event, or when resuming from
a deep sleep mode.
This is vectorized so multiple CPUs can enter the kernel in parallel
without serialization.
The mcpm prefix stands for "multi cluster power management", however
this is usable on single cluster systems as well. Only the basic
structure is introduced here. This will be extended with later patches.
In order not to complexify things more than they currently have to,
the planned work to make runtime adjusted MPIDR based indexing and
dynamic memory allocation for cluster states is postponed to a later
cycle. The MAX_NR_CLUSTERS and MAX_CPUS_PER_CLUSTER static definitions
should be sufficient for those systems expected to be available in the
near future.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
---
arch/arm/Kconfig | 8 ++++
arch/arm/common/Makefile | 1 +
arch/arm/common/mcpm_entry.c | 29 +++++++++++++
arch/arm/common/mcpm_head.S | 86 +++++++++++++++++++++++++++++++++++++++
arch/arm/include/asm/mcpm_entry.h | 35 ++++++++++++++++
5 files changed, 159 insertions(+)
create mode 100644 arch/arm/common/mcpm_entry.c
create mode 100644 arch/arm/common/mcpm_head.S
create mode 100644 arch/arm/include/asm/mcpm_entry.h
diff --git a/arch/arm/Kconfig b/arch/arm/Kconfig
index 67874b82a4..200f559c1c 100644
--- a/arch/arm/Kconfig
+++ b/arch/arm/Kconfig
@@ -1584,6 +1584,14 @@ config HAVE_ARM_TWD
help
This options enables support for the ARM timer and watchdog unit
+config CLUSTER_PM
+ bool "Cluster Power Management Infrastructure"
+ depends on CPU_V7 && SMP
+ help
+ This option provides the common power management infrastructure
+ for (multi-)cluster based systems, such as big.LITTLE based
+ systems.
+
choice
prompt "Memory split"
default VMSPLIT_3G
diff --git a/arch/arm/common/Makefile b/arch/arm/common/Makefile
index e8a4e58f1b..23e85b1fae 100644
--- a/arch/arm/common/Makefile
+++ b/arch/arm/common/Makefile
@@ -13,3 +13,4 @@ obj-$(CONFIG_SHARP_PARAM) += sharpsl_param.o
obj-$(CONFIG_SHARP_SCOOP) += scoop.o
obj-$(CONFIG_PCI_HOST_ITE8152) += it8152.o
obj-$(CONFIG_ARM_TIMER_SP804) += timer-sp.o
+obj-$(CONFIG_CLUSTER_PM) += mcpm_head.o mcpm_entry.o
diff --git a/arch/arm/common/mcpm_entry.c b/arch/arm/common/mcpm_entry.c
new file mode 100644
index 0000000000..3a6d7e70fd
--- /dev/null
+++ b/arch/arm/common/mcpm_entry.c
@@ -0,0 +1,29 @@
+/*
+ * arch/arm/common/mcpm_entry.c -- entry point for multi-cluster PM
+ *
+ * Created by: Nicolas Pitre, March 2012
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+
+#include <asm/mcpm_entry.h>
+#include <asm/barrier.h>
+#include <asm/proc-fns.h>
+#include <asm/cacheflush.h>
+
+extern volatile unsigned long mcpm_entry_vectors[MAX_NR_CLUSTERS][MAX_CPUS_PER_CLUSTER];
+
+void mcpm_set_entry_vector(unsigned cpu, unsigned cluster, void *ptr)
+{
+ unsigned long val = ptr ? virt_to_phys(ptr) : 0;
+ mcpm_entry_vectors[cluster][cpu] = val;
+ __cpuc_flush_dcache_area((void *)&mcpm_entry_vectors[cluster][cpu], 4);
+ outer_clean_range(__pa(&mcpm_entry_vectors[cluster][cpu]),
+ __pa(&mcpm_entry_vectors[cluster][cpu + 1]));
+}
diff --git a/arch/arm/common/mcpm_head.S b/arch/arm/common/mcpm_head.S
new file mode 100644
index 0000000000..794c8ea8c4
--- /dev/null
+++ b/arch/arm/common/mcpm_head.S
@@ -0,0 +1,86 @@
+/*
+ * arch/arm/common/mcpm_head.S -- kernel entry point for multi-cluster PM
+ *
+ * Created by: Nicolas Pitre, March 2012
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/linkage.h>
+#include <asm/mcpm_entry.h>
+
+ .macro pr_dbg string
+#if defined(CONFIG_DEBUG_LL) && defined(DEBUG)
+ b 1901f
+1902: .asciz "CPU"
+1903: .asciz " cluster"
+1904: .asciz ": \string"
+ .align
+1901: adr r0, 1902b
+ bl printascii
+ mov r0, r9
+ bl printhex8
+ adr r0, 1903b
+ bl printascii
+ mov r0, r10
+ bl printhex8
+ adr r0, 1904b
+ bl printascii
+#endif
+ .endm
+
+ .arm
+ .align
+
+ENTRY(mcpm_entry_point)
+
+ THUMB( adr r12, BSYM(1f) )
+ THUMB( bx r12 )
+ THUMB( .thumb )
+1:
+ mrc p15, 0, r0, c0, c0, 5 @ MPIDR
+ ubfx r9, r0, #0, #4 @ r9 = cpu
+ ubfx r10, r0, #8, #4 @ r10 = cluster
+ mov r3, #MAX_CPUS_PER_CLUSTER
+ mla r4, r3, r10, r9 @ r4 = canonical CPU index
+ cmp r4, #(MAX_CPUS_PER_CLUSTER * MAX_NR_CLUSTERS)
+ blo 2f
+
+ /* We didn't expect this CPU. Try to cheaply make it quiet. */
+1: wfi
+ wfe
+ b 1b
+
+2: pr_dbg "kernel mcpm_entry_point\n"
+
+ /*
+ * MMU is off so we need to get to mcpm_entry_vectors in a
+ * position independent way.
+ */
+ adr r5, 3f
+ ldr r6, [r5]
+ add r6, r5, r6 @ r6 = mcpm_entry_vectors
+
+mcpm_entry_gated:
+ ldr r5, [r6, r4, lsl #2] @ r5 = CPU entry vector
+ cmp r5, #0
+ wfeeq
+ beq mcpm_entry_gated
+ pr_dbg "released\n"
+ bx r5
+
+ .align 2
+
+3: .word mcpm_entry_vectors - .
+
+ENDPROC(mcpm_entry_point)
+
+ .bss
+ .align 5
+
+ .type mcpm_entry_vectors, #object
+ENTRY(mcpm_entry_vectors)
+ .space 4 * MAX_NR_CLUSTERS * MAX_CPUS_PER_CLUSTER
diff --git a/arch/arm/include/asm/mcpm_entry.h b/arch/arm/include/asm/mcpm_entry.h
new file mode 100644
index 0000000000..cc10ebbd2e
--- /dev/null
+++ b/arch/arm/include/asm/mcpm_entry.h
@@ -0,0 +1,35 @@
+/*
+ * arch/arm/include/asm/mcpm_entry.h
+ *
+ * Created by: Nicolas Pitre, April 2012
+ * Copyright: (C) 2012-2013 Linaro Limited
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#ifndef MCPM_ENTRY_H
+#define MCPM_ENTRY_H
+
+#define MAX_CPUS_PER_CLUSTER 4
+#define MAX_NR_CLUSTERS 2
+
+#ifndef __ASSEMBLY__
+
+/*
+ * Platform specific code should use this symbol to set up secondary
+ * entry location for processors to use when released from reset.
+ */
+extern void mcpm_entry_point(void);
+
+/*
+ * This is used to indicate where the given CPU from given cluster should
+ * branch once it is ready to re-enter the kernel using ptr, or NULL if it
+ * should be gated. A gated CPU is held in a WFE loop until its vector
+ * becomes non NULL.
+ */
+void mcpm_set_entry_vector(unsigned cpu, unsigned cluster, void *ptr);
+
+#endif /* ! __ASSEMBLY__ */
+#endif
--
1.8.1.2
^ permalink raw reply related
* [PATCH v3 00/15] multi-cluster power management
From: Nicolas Pitre @ 2013-01-29 7:50 UTC (permalink / raw)
To: linux-arm-kernel
This is version 3 of the patch series required to safely power up
and down CPUs in a cluster as can be found in b.L systems. Also
included are the needed patches to allow CPU hotplug on RTSM configured
for big.LITTLE.
This is now called "Multi-Cluster Power Management", or mcpm for short.
At least that makes for a prefix which is not already used in the kernel
and therefore is unlikely to be ambiguous. Despite the name, this can be
used on single cluster systems as well if appropriate.
Please refer to http://article.gmane.org/gmane.linux.ports.arm.kernel/208625
for the initial series and particularly the cover page blurb for this work.
Thanks to those who provided review comments.
Changes from v2:
- The bL_ prefix has been changed into mcpm_ and surroundings adjusted
accordingly.
- Documentation moved up one level in Documentation/arm/.
- Clarifications in commit log for patch #1 about future work.
- The debug macro in mcpm_head.S now displays CPU and cluster numbers.
- Patch improving mcpm_cpu_die() folded into the original patch that
created it.
- Return -EADDRNOTAVAIL on ioremap failure.
- The auxcr patch moved down in the series to better identify dependencies.
Changes from v1:
- Pulled in Rob Herring's auxcr accessor patch and converted this series
to it.
- VMajor rework of various barriers (some DSBs demoted to DMBs, etc.)
- The sync_mem() macro is now split and enhanced to properly process the
cache for writers and readers in the cluster critical region helpers.
- BL_NR_CLUSTERS and BL_CPUS_PER_CLUSTER renamed to BL_MAX_CLUSTERS
and BL_MAX_CPUS_PER_CLUSTER.
- Removed unused C definitions and prototypes for vlocks.
- Simplified the vlock memory allocation.
- The vlock code is GPL v2.
- Replaced MPIDR inline asm by read_cpuid_mpidr().
- Use of MPIDR_AFFINITY_LEVEL() to replace explicit shifts and masks.
- Dropped gic_cpu_if_down().
- Added a DSB before SEV and WFI.
- Fixed power_up_setup helper prototype.
- Nuked smp_wmb() in bL_set_entry_vector().
- Moved the CCI driver to drivers/bus/.
- Dependency on CONFIG_EXPERIMENTAL removed.
- Leftover garbage in Makefile removed.
- Added/clarified various comments in the assembly code.
- Some documentation typos fixed.
- Copyright notices updated to 2013
Still not addressed yet in this series:
- The CCI and DCSCB device tree binding descriptions.
Diffstat:
Documentation/arm/cluster-pm-race-avoidance.txt | 498 ++++++++++++++++++
Documentation/arm/vlocks.txt | 211 ++++++++
arch/arm/Kconfig | 8 +
arch/arm/common/Makefile | 1 +
arch/arm/common/mcpm_entry.c | 314 +++++++++++
arch/arm/common/mcpm_head.S | 219 ++++++++
arch/arm/common/mcpm_platsmp.c | 85 +++
arch/arm/common/vlock.S | 108 ++++
arch/arm/common/vlock.h | 29 +
arch/arm/include/asm/cp15.h | 14 +
arch/arm/include/asm/mach/arch.h | 3 +
arch/arm/include/asm/mcpm_entry.h | 190 +++++++
arch/arm/kernel/setup.c | 5 +-
arch/arm/mach-vexpress/Kconfig | 9 +
arch/arm/mach-vexpress/Makefile | 1 +
arch/arm/mach-vexpress/core.h | 2 +
arch/arm/mach-vexpress/dcscb.c | 249 +++++++++
arch/arm/mach-vexpress/dcscb_setup.S | 80 +++
arch/arm/mach-vexpress/platsmp.c | 12 +
arch/arm/mach-vexpress/v2m.c | 2 +-
drivers/bus/Kconfig | 5 +
drivers/bus/Makefile | 2 +
drivers/bus/arm-cci.c | 124 +++++
drivers/cpuidle/cpuidle-calxeda.c | 14 -
include/linux/arm-cci.h | 30 ++
25 files changed, 2199 insertions(+), 16 deletions(-)
Nicolas
^ permalink raw reply
* [PATCH 2/5] spi: pl022: use generic DMA slave configuration if possible
From: Andy Shevchenko @ 2013-01-29 7:49 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359410300-26113-3-git-send-email-arnd@arndb.de>
On Mon, 2013-01-28 at 21:58 +0000, Arnd Bergmann wrote:
> With the new OF DMA binding, it is possible to completely avoid the
> need for platform_data for configuring a DMA channel. In cases where the
> platform has already been converted, calling dma_request_slave_channel
> should get all the necessary information from the device tree.
>
> Like the patch that converts the dw_dma controller, this is completely
> untested and is looking for someone to try it out.
>
> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
> Cc: Grant Likely <grant.likely@secretlab.ca>
> Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
> Cc: spi-devel-general at lists.sourceforge.net
> Cc: Viresh Kumar <viresh.kumar@linaro.org>
> Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
> Cc: Vinod Koul <vinod.koul@linux.intel.com>
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: linux-arm-kernel at lists.infradead.org
> ---
> .../devicetree/bindings/spi/spi_pl022.txt | 36 ++++++++++++++++++
> drivers/spi/spi-pl022.c | 43 +++++++++++++++++++++-
> 2 files changed, 77 insertions(+), 2 deletions(-)
>
> --- a/drivers/spi/spi-pl022.c
> +++ b/drivers/spi/spi-pl022.c
> @@ -1139,6 +1139,35 @@ err_no_rxchan:
> return -ENODEV;
> }
>
> +static int pl022_dma_autoprobe(struct pl022 *pl022)
> +{
> + struct device *dev = &pl022->adev->dev;
> +
> + /* automatically configure DMA channels from platform, normally using DT */
> + pl022->dma_rx_channel = dma_request_slave_channel(dev, "rx");
> + if (!pl022->dma_rx_channel)
> + goto err_no_rxchan;
> +
> + pl022->dma_tx_channel = dma_request_slave_channel(dev, "tx");
> + if (!pl022->dma_tx_channel)
> + goto err_no_txchan;
> +
> + pl022->dummypage = kmalloc(PAGE_SIZE, GFP_KERNEL);
Where this memory will be freed?
In dependence of the answer could you consider to use
devm_kmalloc or __get_free_page?
> + if (!pl022->dummypage)
> + goto err_no_dummypage;
> +
> + return 0;
> +
> +err_no_dummypage:
> + dma_release_channel(pl022->dma_tx_channel);
> + pl022->dma_tx_channel = NULL;
> +err_no_txchan:
> + dma_release_channel(pl022->dma_rx_channel);
> + pl022->dma_rx_channel = NULL;
> +err_no_rxchan:
> + return -ENODEV;
> +}
> +
> static void terminate_dma(struct pl022 *pl022)
> {
> struct dma_chan *rxchan = pl022->dma_rx_channel;
> @@ -1167,6 +1196,11 @@ static inline int configure_dma(struct pl022 *pl022)
> return -ENODEV;
> }
>
> +static inline int pl022_dma_autoprobe(struct pl022 *pl022)
> +{
> + return 0;
> +}
> +
> static inline int pl022_dma_probe(struct pl022 *pl022)
> {
> return 0;
> @@ -2226,8 +2260,13 @@ static int pl022_probe(struct amba_device *adev, const struct amba_id *id)
> goto err_no_irq;
> }
>
> - /* Get DMA channels */
> - if (platform_info->enable_dma) {
> + /* Get DMA channels, try autoconfiguration first */
> + status = pl022_dma_autoprobe(pl022);
> +
> + /* If that failed, use channels from platform_info */
> + if (status == 0)
> + platform_info->enable_dma = 1;
> + else if (platform_info->enable_dma) {
> status = pl022_dma_probe(pl022);
> if (status != 0)
> platform_info->enable_dma = 0;
--
Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Intel Finland Oy
^ permalink raw reply
* [PATCH V2 6/6] ARM: davinci: da850: add tps6507x regulator DT data
From: Vishwanathrao Badarkhe, Manish @ 2013-01-29 7:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445134-13323-1-git-send-email-manishv.b@ti.com>
Add tps6507x regulator device tree data to da850-evm by
adding regulator consumers with tightened constraints
and regulator-name.TPS6507x regulator handle can be obtained
by using this regulator name.
Regulator constraints are added as per da850 board file.
Regulator names are given as per maximum output voltage the
regulator is capable to provide.
for e.g. regulator name for dcdc1 is "VDCDC1_3.3V".
Also, add tps6507x PMIC I2C slave device under I2C0 node.
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
---
Changes since V1:
- No change
:100644 100644 c9ed683... 58e6961... M arch/arm/boot/dts/da850-evm.dts
arch/arm/boot/dts/da850-evm.dts | 63 +++++++++++++++++++++++++++++++++++++++
1 files changed, 63 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index c9ed683..58e6961 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -31,6 +31,10 @@
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
+
+ tps: tps at 48 {
+ reg = <0x48>;
+ };
};
};
nand_cs3 at 62000000 {
@@ -38,4 +42,63 @@
pinctrl-names = "default";
pinctrl-0 = <&nand_cs3_pins>;
};
+ vbat: fixedregulator at 0 {
+ compatible = "regulator-fixed";
+ regulator-name = "vbat";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ regulator-boot-on;
+ };
+};
+
+/include/ "tps6507x.dtsi"
+
+&tps {
+ vdcdc1_2-supply = <&vbat>;
+ vdcdc3-supply = <&vbat>;
+ vldo1_2-supply = <&vbat>;
+
+ regulators {
+ vdcdc1_reg: regulator at 0 {
+ regulator-name = "VDCDC1_3.3V";
+ regulator-min-microvolt = <3150000>;
+ regulator-max-microvolt = <3450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ vdcdc2_reg: regulator at 1 {
+ regulator-name = "VDCDC2_3.3V";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <3450000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,defdcdc_default = <1>;
+ };
+
+ vdcdc3_reg: regulator at 2 {
+ regulator-name = "VDCDC3_1.2V";
+ regulator-min-microvolt = <950000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-boot-on;
+ ti,defdcdc_default = <1>;
+ };
+
+ ldo1_reg: regulator at 3 {
+ regulator-name = "LDO1_1.8V";
+ regulator-min-microvolt = <1710000>;
+ regulator-max-microvolt = <1890000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ ldo2_reg: regulator at 4 {
+ regulator-name = "LDO2_1.2V";
+ regulator-min-microvolt = <1140000>;
+ regulator-max-microvolt = <1320000>;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+ };
};
--
1.7.4.1
^ permalink raw reply related
* [PATCH V2 5/6] ARM: regulator: add tps6507x device tree data
From: Vishwanathrao Badarkhe, Manish @ 2013-01-29 7:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445134-13323-1-git-send-email-manishv.b@ti.com>
Add device tree data for tps6507x regulator by adding
all tps6507x regulator nodes. Regulators are initialized
based on compatible name provided in tps6507x DT file.
All tps6507x PMIC regulator device tree nodes are placed
in a separate device tree include file (tps6507x.dtsi).
tps6507x.dtsi file is created using datasheet
http://www.ti.com/lit/ds/symlink/tps65070.pdf
Tested on da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
---
Changes since V1:
- Updated Copyright information.
:000000 100644 0000000... 4c326e5... A arch/arm/boot/dts/tps6507x.dtsi
arch/arm/boot/dts/tps6507x.dtsi | 47 +++++++++++++++++++++++++++++++++++++++
1 files changed, 47 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/tps6507x.dtsi b/arch/arm/boot/dts/tps6507x.dtsi
new file mode 100644
index 0000000..4c326e5
--- /dev/null
+++ b/arch/arm/boot/dts/tps6507x.dtsi
@@ -0,0 +1,47 @@
+/*
+ * Copyright (C) 2013 Texas Instruments Incorporated - http://www.ti.com/
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/*
+ * Integrated Power Management Chip
+ * http://www.ti.com/lit/ds/symlink/tps65070.pdf
+ */
+
+&tps {
+ compatible = "ti,tps6507x";
+
+ regulators {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vdcdc1_reg: regulator at 0 {
+ reg = <0>;
+ regulator-compatible = "VDCDC1";
+ };
+
+ vdcdc2_reg: regulator at 1 {
+ reg = <1>;
+ regulator-compatible = "VDCDC2";
+ };
+
+ vdcdc3_reg: regulator at 2 {
+ reg = <2>;
+ regulator-compatible = "VDCDC3";
+ };
+
+ ldo1_reg: regulator at 3 {
+ reg = <3>;
+ regulator-compatible = "LDO1";
+ };
+
+ ldo2_reg: regulator at 4 {
+ reg = <4>;
+ regulator-compatible = "LDO2";
+ };
+
+ };
+};
--
1.7.4.1
^ permalink raw reply related
* [PATCH V2 4/6] mfd: tps6507x: add device-tree support.
From: Vishwanathrao Badarkhe, Manish @ 2013-01-29 7:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445134-13323-1-git-send-email-manishv.b@ti.com>
Add device tree based initialization support for TI's
tps6507x mfd device.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
---
Changes since V1:
- updated subject line for commit.
:100644 100644 409afa2... 5ad4b77... M drivers/mfd/tps6507x.c
drivers/mfd/tps6507x.c | 9 +++++++++
1 files changed, 9 insertions(+), 0 deletions(-)
diff --git a/drivers/mfd/tps6507x.c b/drivers/mfd/tps6507x.c
index 409afa2..5ad4b77 100644
--- a/drivers/mfd/tps6507x.c
+++ b/drivers/mfd/tps6507x.c
@@ -19,6 +19,7 @@
#include <linux/init.h>
#include <linux/slab.h>
#include <linux/i2c.h>
+#include <linux/of_device.h>
#include <linux/mfd/core.h>
#include <linux/mfd/tps6507x.h>
@@ -116,11 +117,19 @@ static const struct i2c_device_id tps6507x_i2c_id[] = {
};
MODULE_DEVICE_TABLE(i2c, tps6507x_i2c_id);
+#ifdef CONFIG_OF
+static struct of_device_id tps6507x_of_match[] = {
+ {.compatible = "ti,tps6507x", },
+ {},
+};
+MODULE_DEVICE_TABLE(of, tps6507x_of_match);
+#endif
static struct i2c_driver tps6507x_i2c_driver = {
.driver = {
.name = "tps6507x",
.owner = THIS_MODULE,
+ .of_match_table = of_match_ptr(tps6507x_of_match),
},
.probe = tps6507x_i2c_probe,
.remove = tps6507x_i2c_remove,
--
1.7.4.1
^ permalink raw reply related
* [PATCH V2 3/6] ARM: davinci: da850: add DT node for I2C0
From: Vishwanathrao Badarkhe, Manish @ 2013-01-29 7:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1359445134-13323-1-git-send-email-manishv.b@ti.com>
Add I2C0 device tree node information to da850-evm.
Also, add I2C0 pin muxing information in da850-evm.
Signed-off-by: Vishwanathrao Badarkhe, Manish <manishv.b@ti.com>
---
Changes since V1:
- Updated i2c0 node names in dts and dtsi file.
- Removed interrupt parent from i2c0 node.
- Handled i2c0 pin mux inside i2c0 node.
:100644 100644 433027f... c9ed683... M arch/arm/boot/dts/da850-evm.dts
:100644 100644 5e0eb5c... 245ab9a... M arch/arm/boot/dts/da850.dtsi
arch/arm/boot/dts/da850-evm.dts | 5 +++++
arch/arm/boot/dts/da850.dtsi | 15 +++++++++++++++
2 files changed, 20 insertions(+), 0 deletions(-)
diff --git a/arch/arm/boot/dts/da850-evm.dts b/arch/arm/boot/dts/da850-evm.dts
index 433027f..c9ed683 100644
--- a/arch/arm/boot/dts/da850-evm.dts
+++ b/arch/arm/boot/dts/da850-evm.dts
@@ -27,6 +27,11 @@
serial2: serial at 1d0d000 {
status = "okay";
};
+ i2c0: i2c0 at 1c22000 {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&i2c0_pins>;
+ };
};
nand_cs3 at 62000000 {
status = "okay";
diff --git a/arch/arm/boot/dts/da850.dtsi b/arch/arm/boot/dts/da850.dtsi
index 5e0eb5c..245ab9a 100644
--- a/arch/arm/boot/dts/da850.dtsi
+++ b/arch/arm/boot/dts/da850.dtsi
@@ -56,6 +56,12 @@
0x30 0x01100000 0x0ff00000
>;
};
+ i2c0_pins: pinmux_i2c0_pins {
+ pinctrl-single,bits = <
+ /* I2C0_SDA,I2C0_SCL */
+ 0x10 0x00002200 0x0000ff00
+ >;
+ };
};
serial0: serial at 1c42000 {
compatible = "ns16550a";
@@ -81,6 +87,15 @@
interrupts = <61>;
status = "disabled";
};
+ i2c0: i2c0 at 1c22000 {
+ compatible = "ti,davinci-i2c";
+ reg = <0x22000 0x1000>;
+ clock-frequency = <100000>;
+ interrupts = <15>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
};
nand_cs3 at 62000000 {
compatible = "ti,davinci-nand";
--
1.7.4.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox