* [PATCH V4 3/5] firmware: ti_sci: Add support for Device control
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161018230837.6515-1-nm@ti.com>
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.
TI-SCI message protocol provides support for management of various
hardware entitites within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
We introduce the fundamental device management capability support to
the driver protocol as part of this change.
[d-gerlach at ti.com: Contributed device reset handling]
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since v3: none
V3: https://patchwork.kernel.org/patch/9317843/
drivers/firmware/ti_sci.c | 433 +++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 98 ++++++++
include/linux/soc/ti/ti_sci_protocol.h | 91 +++++++
3 files changed, 622 insertions(+)
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 5e99d7c18276..c7b25ccf6f07 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -495,6 +495,437 @@ static int ti_sci_cmd_get_revision(struct ti_sci_info *info)
}
/**
+ * ti_sci_is_response_ack() - Generic ACK/NACK message checkup
+ * @r: pointer to response buffer
+ *
+ * Return: true if the response was an ACK, else returns false.
+ */
+static inline bool ti_sci_is_response_ack(void *r)
+{
+ struct ti_sci_msg_hdr *hdr = r;
+
+ return hdr->flags & TI_SCI_FLAG_RESP_GENERIC_ACK ? true : false;
+}
+
+/**
+ * ti_sci_set_device_state() - Set device state helper
+ * @handle: pointer to TI SCI handle
+ * @id: Device identifier
+ * @flags: flags to setup for the device
+ * @state: State to move the device to
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_set_device_state(const struct ti_sci_handle *handle,
+ u32 id, u32 flags, u8 state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_device_state *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_DEVICE_STATE,
+ flags | TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_device_state *)xfer->xfer_buf;
+ req->id = id;
+ req->state = state;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_get_device_state() - Get device state helper
+ * @handle: Handle to the device
+ * @id: Device Identifier
+ * @clcnt: Pointer to Context Loss Count
+ * @resets: pointer to resets
+ * @p_state: pointer to p_state
+ * @c_state: pointer to c_state
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_get_device_state(const struct ti_sci_handle *handle,
+ u32 id, u32 *clcnt, u32 *resets,
+ u8 *p_state, u8 *c_state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_device_state *req;
+ struct ti_sci_msg_resp_get_device_state *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ if (!clcnt && !resets && !p_state && !c_state)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ /* Response is expected, so need of any flags */
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_DEVICE_STATE,
+ 0, sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_device_state *)xfer->xfer_buf;
+ req->id = id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_device_state *)xfer->xfer_buf;
+ if (!ti_sci_is_response_ack(resp)) {
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ if (clcnt)
+ *clcnt = resp->context_loss_count;
+ if (resets)
+ *resets = resp->resets;
+ if (p_state)
+ *p_state = resp->programmed_state;
+ if (c_state)
+ *c_state = resp->current_state;
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_device() - command to request for device managed by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ *
+ * NOTE: The request is for exclusive access for the processor.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_get_device(const struct ti_sci_handle *handle, u32 id)
+{
+ return ti_sci_set_device_state(handle, id,
+ MSG_FLAG_DEVICE_EXCLUSIVE,
+ MSG_DEVICE_SW_STATE_ON);
+}
+
+/**
+ * ti_sci_cmd_idle_device() - Command to idle a device managed by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_idle_device(const struct ti_sci_handle *handle, u32 id)
+{
+ return ti_sci_set_device_state(handle, id,
+ MSG_FLAG_DEVICE_EXCLUSIVE,
+ MSG_DEVICE_SW_STATE_RETENTION);
+}
+
+/**
+ * ti_sci_cmd_put_device() - command to release a device managed by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_put_device(const struct ti_sci_handle *handle, u32 id)
+{
+ return ti_sci_set_device_state(handle, id,
+ 0, MSG_DEVICE_SW_STATE_AUTO_OFF);
+}
+
+/**
+ * ti_sci_cmd_dev_is_valid() - Is the device valid
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ *
+ * Return: 0 if all went fine and the device ID is valid, else return
+ * appropriate error.
+ */
+static int ti_sci_cmd_dev_is_valid(const struct ti_sci_handle *handle, u32 id)
+{
+ u8 unused;
+
+ /* check the device state which will also tell us if the ID is valid */
+ return ti_sci_get_device_state(handle, id, NULL, NULL, NULL, &unused);
+}
+
+/**
+ * ti_sci_cmd_dev_get_clcnt() - Get context loss counter
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @count: Pointer to Context Loss counter to populate
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_get_clcnt(const struct ti_sci_handle *handle, u32 id,
+ u32 *count)
+{
+ return ti_sci_get_device_state(handle, id, count, NULL, NULL, NULL);
+}
+
+/**
+ * ti_sci_cmd_dev_is_idle() - Check if the device is requested to be idle
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @r_state: true if requested to be idle
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_idle(const struct ti_sci_handle *handle, u32 id,
+ bool *r_state)
+{
+ int ret;
+ u8 state;
+
+ if (!r_state)
+ return -EINVAL;
+
+ ret = ti_sci_get_device_state(handle, id, NULL, NULL, &state, NULL);
+ if (ret)
+ return ret;
+
+ *r_state = (state == MSG_DEVICE_SW_STATE_RETENTION);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_dev_is_stop() - Check if the device is requested to be stopped
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @r_state: true if requested to be stopped
+ * @curr_state: true if currently stopped.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_stop(const struct ti_sci_handle *handle, u32 id,
+ bool *r_state, bool *curr_state)
+{
+ int ret;
+ u8 p_state, c_state;
+
+ if (!r_state && !curr_state)
+ return -EINVAL;
+
+ ret =
+ ti_sci_get_device_state(handle, id, NULL, NULL, &p_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (r_state)
+ *r_state = (p_state == MSG_DEVICE_SW_STATE_AUTO_OFF);
+ if (curr_state)
+ *curr_state = (c_state == MSG_DEVICE_HW_STATE_OFF);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_dev_is_on() - Check if the device is requested to be ON
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @r_state: true if requested to be ON
+ * @curr_state: true if currently ON and active
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_on(const struct ti_sci_handle *handle, u32 id,
+ bool *r_state, bool *curr_state)
+{
+ int ret;
+ u8 p_state, c_state;
+
+ if (!r_state && !curr_state)
+ return -EINVAL;
+
+ ret =
+ ti_sci_get_device_state(handle, id, NULL, NULL, &p_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (r_state)
+ *r_state = (p_state == MSG_DEVICE_SW_STATE_ON);
+ if (curr_state)
+ *curr_state = (c_state == MSG_DEVICE_HW_STATE_ON);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_dev_is_trans() - Check if the device is currently transitioning
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @curr_state: true if currently transitioning.
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_dev_is_trans(const struct ti_sci_handle *handle, u32 id,
+ bool *curr_state)
+{
+ int ret;
+ u8 state;
+
+ if (!curr_state)
+ return -EINVAL;
+
+ ret = ti_sci_get_device_state(handle, id, NULL, NULL, NULL, &state);
+ if (ret)
+ return ret;
+
+ *curr_state = (state == MSG_DEVICE_HW_STATE_TRANS);
+
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_set_device_resets() - command to set resets for device managed
+ * by TISCI
+ * @handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * @id: Device Identifier
+ * @reset_state: Device specific reset bit field
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_set_device_resets(const struct ti_sci_handle *handle,
+ u32 id, u32 reset_state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_device_resets *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_DEVICE_RESETS,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_device_resets *)xfer->xfer_buf;
+ req->id = id;
+ req->resets = reset_state;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_device_resets() - Get reset state for device managed
+ * by TISCI
+ * @handle: Pointer to TISCI handle
+ * @id: Device Identifier
+ * @reset_state: Pointer to reset state to populate
+ *
+ * Return: 0 if all went fine, else return appropriate error.
+ */
+static int ti_sci_cmd_get_device_resets(const struct ti_sci_handle *handle,
+ u32 id, u32 *reset_state)
+{
+ return ti_sci_get_device_state(handle, id, NULL, reset_state, NULL,
+ NULL);
+}
+
+/*
+ * ti_sci_setup_ops() - Setup the operations structures
+ * @info: pointer to TISCI pointer
+ */
+static void ti_sci_setup_ops(struct ti_sci_info *info)
+{
+ struct ti_sci_ops *ops = &info->handle.ops;
+ struct ti_sci_dev_ops *dops = &ops->dev_ops;
+
+ dops->get_device = ti_sci_cmd_get_device;
+ dops->idle_device = ti_sci_cmd_idle_device;
+ dops->put_device = ti_sci_cmd_put_device;
+
+ dops->is_valid = ti_sci_cmd_dev_is_valid;
+ dops->get_context_loss_count = ti_sci_cmd_dev_get_clcnt;
+ dops->is_idle = ti_sci_cmd_dev_is_idle;
+ dops->is_stop = ti_sci_cmd_dev_is_stop;
+ dops->is_on = ti_sci_cmd_dev_is_on;
+ dops->is_transitioning = ti_sci_cmd_dev_is_trans;
+ dops->set_device_resets = ti_sci_cmd_set_device_resets;
+ dops->get_device_resets = ti_sci_cmd_get_device_resets;
+}
+
+/**
* ti_sci_get_handle() - Get the TI SCI handle for a device
* @dev: Pointer to device for which we want SCI handle
*
@@ -727,6 +1158,8 @@ static int ti_sci_probe(struct platform_device *pdev)
goto out;
}
+ ti_sci_setup_ops(info);
+
dev_info(dev, "ABI: %d.%d (firmware rev 0x%04x '%s')\n",
info->handle.version.abi_major, info->handle.version.abi_minor,
info->handle.version.firmware_revision,
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index e9dc53f26e0e..29ce0532a7ca 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -47,6 +47,11 @@
#define TI_SCI_MSG_WAKE_REASON 0x0003
#define TI_SCI_MSG_GOODBYE 0x0004
+/* Device requests */
+#define TI_SCI_MSG_SET_DEVICE_STATE 0x0200
+#define TI_SCI_MSG_GET_DEVICE_STATE 0x0201
+#define TI_SCI_MSG_SET_DEVICE_RESETS 0x0202
+
/**
* struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
* @type: Type of messages: One of TI_SCI_MSG* values
@@ -90,4 +95,97 @@ struct ti_sci_msg_resp_version {
u8 abi_minor;
} __packed;
+/**
+ * struct ti_sci_msg_req_set_device_state - Set the desired state of the device
+ * @hdr: Generic header
+ * @id: Indicates which device to modify
+ * @reserved: Reserved space in message, must be 0 for backward compatibility
+ * @state: The desired state of the device.
+ *
+ * Certain flags can also be set to alter the device state:
+ * + MSG_FLAG_DEVICE_WAKE_ENABLED - Configure the device to be a wake source.
+ * The meaning of this flag will vary slightly from device to device and from
+ * SoC to SoC but it generally allows the device to wake the SoC out of deep
+ * suspend states.
+ * + MSG_FLAG_DEVICE_RESET_ISO - Enable reset isolation for this device.
+ * + MSG_FLAG_DEVICE_EXCLUSIVE - Claim this device exclusively. When passed
+ * with STATE_RETENTION or STATE_ON, it will claim the device exclusively.
+ * If another host already has this device set to STATE_RETENTION or STATE_ON,
+ * the message will fail. Once successful, other hosts attempting to set
+ * STATE_RETENTION or STATE_ON will fail.
+ *
+ * Request type is TI_SCI_MSG_SET_DEVICE_STATE, responded with a generic
+ * ACK/NACK message.
+ */
+struct ti_sci_msg_req_set_device_state {
+ /* Additional hdr->flags options */
+#define MSG_FLAG_DEVICE_WAKE_ENABLED TI_SCI_MSG_FLAG(8)
+#define MSG_FLAG_DEVICE_RESET_ISO TI_SCI_MSG_FLAG(9)
+#define MSG_FLAG_DEVICE_EXCLUSIVE TI_SCI_MSG_FLAG(10)
+ struct ti_sci_msg_hdr hdr;
+ u32 id;
+ u32 reserved;
+
+#define MSG_DEVICE_SW_STATE_AUTO_OFF 0
+#define MSG_DEVICE_SW_STATE_RETENTION 1
+#define MSG_DEVICE_SW_STATE_ON 2
+ u8 state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_device_state - Request to get device.
+ * @hdr: Generic header
+ * @id: Device Identifier
+ *
+ * Request type is TI_SCI_MSG_GET_DEVICE_STATE, responded device state
+ * information
+ */
+struct ti_sci_msg_req_get_device_state {
+ struct ti_sci_msg_hdr hdr;
+ u32 id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_device_state - Response to get device request.
+ * @hdr: Generic header
+ * @context_loss_count: Indicates how many times the device has lost context. A
+ * driver can use this monotonic counter to determine if the device has
+ * lost context since the last time this message was exchanged.
+ * @resets: Programmed state of the reset lines.
+ * @programmed_state: The state as programmed by set_device.
+ * - Uses the MSG_DEVICE_SW_* macros
+ * @current_state: The actual state of the hardware.
+ *
+ * Response to request TI_SCI_MSG_GET_DEVICE_STATE.
+ */
+struct ti_sci_msg_resp_get_device_state {
+ struct ti_sci_msg_hdr hdr;
+ u32 context_loss_count;
+ u32 resets;
+ u8 programmed_state;
+#define MSG_DEVICE_HW_STATE_OFF 0
+#define MSG_DEVICE_HW_STATE_ON 1
+#define MSG_DEVICE_HW_STATE_TRANS 2
+ u8 current_state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_set_device_resets - Set the desired resets
+ * configuration of the device
+ * @hdr: Generic header
+ * @id: Indicates which device to modify
+ * @resets: A bit field of resets for the device. The meaning, behavior,
+ * and usage of the reset flags are device specific. 0 for a bit
+ * indicates releasing the reset represented by that bit while 1
+ * indicates keeping it held.
+ *
+ * Request type is TI_SCI_MSG_SET_DEVICE_RESETS, responded with a generic
+ * ACK/NACK message.
+ */
+struct ti_sci_msg_req_set_device_resets {
+ struct ti_sci_msg_hdr hdr;
+ u32 id;
+ u32 resets;
+} __packed;
+
#endif /* __TI_SCI_H */
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index e73483fd5327..87fa73851471 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -33,12 +33,103 @@ struct ti_sci_version_info {
char firmware_description[32];
};
+struct ti_sci_handle;
+
+/**
+ * struct ti_sci_dev_ops - Device control operations
+ * @get_device: Command to request for device managed by TISCI
+ * Returns 0 for successful exclusive request, else returns
+ * corresponding error message.
+ * @idle_device: Command to idle a device managed by TISCI
+ * Returns 0 for successful exclusive request, else returns
+ * corresponding error message.
+ * @put_device: Command to release a device managed by TISCI
+ * Returns 0 for successful release, else returns corresponding
+ * error message.
+ * @is_valid: Check if the device ID is a valid ID.
+ * Returns 0 if the ID is valid, else returns corresponding error.
+ * @get_context_loss_count: Command to retrieve context loss counter - this
+ * increments every time the device looses context. Overflow
+ * is possible.
+ * - count: pointer to u32 which will retrieve counter
+ * Returns 0 for successful information request and count has
+ * proper data, else returns corresponding error message.
+ * @is_idle: Reports back about device idle state
+ * - req_state: Returns requested idle state
+ * Returns 0 for successful information request and req_state and
+ * current_state has proper data, else returns corresponding error
+ * message.
+ * @is_stop: Reports back about device stop state
+ * - req_state: Returns requested stop state
+ * - current_state: Returns current stop state
+ * Returns 0 for successful information request and req_state and
+ * current_state has proper data, else returns corresponding error
+ * message.
+ * @is_on: Reports back about device ON(or active) state
+ * - req_state: Returns requested ON state
+ * - current_state: Returns current ON state
+ * Returns 0 for successful information request and req_state and
+ * current_state has proper data, else returns corresponding error
+ * message.
+ * @is_transitioning: Reports back if the device is in the middle of transition
+ * of state.
+ * -current_state: Returns 'true' if currently transitioning.
+ * @set_device_resets: Command to configure resets for device managed by TISCI.
+ * -reset_state: Device specific reset bit field
+ * Returns 0 for successful request, else returns
+ * corresponding error message.
+ * @get_device_resets: Command to read state of resets for device managed
+ * by TISCI.
+ * -reset_state: pointer to u32 which will retrieve resets
+ * Returns 0 for successful request, else returns
+ * corresponding error message.
+ *
+ * NOTE: for all these functions, the following parameters are generic in
+ * nature:
+ * -handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * -id: Device Identifier
+ *
+ * Request for the device - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_device with put_device. No refcounting is
+ * managed by driver for that purpose.
+ */
+struct ti_sci_dev_ops {
+ int (*get_device)(const struct ti_sci_handle *handle, u32 id);
+ int (*idle_device)(const struct ti_sci_handle *handle, u32 id);
+ int (*put_device)(const struct ti_sci_handle *handle, u32 id);
+ int (*is_valid)(const struct ti_sci_handle *handle, u32 id);
+ int (*get_context_loss_count)(const struct ti_sci_handle *handle,
+ u32 id, u32 *count);
+ int (*is_idle)(const struct ti_sci_handle *handle, u32 id,
+ bool *requested_state);
+ int (*is_stop)(const struct ti_sci_handle *handle, u32 id,
+ bool *req_state, bool *current_state);
+ int (*is_on)(const struct ti_sci_handle *handle, u32 id,
+ bool *req_state, bool *current_state);
+ int (*is_transitioning)(const struct ti_sci_handle *handle, u32 id,
+ bool *current_state);
+ int (*set_device_resets)(const struct ti_sci_handle *handle, u32 id,
+ u32 reset_state);
+ int (*get_device_resets)(const struct ti_sci_handle *handle, u32 id,
+ u32 *reset_state);
+};
+
+/**
+ * struct ti_sci_ops - Function support for TI SCI
+ * @dev_ops: Device specific operations
+ */
+struct ti_sci_ops {
+ struct ti_sci_dev_ops dev_ops;
+};
+
/**
* struct ti_sci_handle - Handle returned to TI SCI clients for usage.
* @version: structure containing version information
+ * @ops: operations that are made available to TI SCI clients
*/
struct ti_sci_handle {
struct ti_sci_version_info version;
+ struct ti_sci_ops ops;
};
#if IS_ENABLED(CONFIG_TI_SCI_PROTOCOL)
--
2.10.0
^ permalink raw reply related
* [PATCH V4 4/5] firmware: ti_sci: Add support for Clock control
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161018230837.6515-1-nm@ti.com>
Texas Instrument's System Control Interface (TI-SCI) Message Protocol
is used in Texas Instrument's System on Chip (SoC) such as those
in keystone family K2G SoC to communicate between various compute
processors with a central system controller entity.
TI-SCI message protocol provides support for management of various
hardware entities within the SoC. Add support driver to allow
communication with system controller entity within the SoC using the
mailbox client.
In general, we expect to function at a device level of abstraction,
however, for proper operation of hardware blocks, many clocks directly
supplying the hardware block needs to be queried or configured.
Introduce support for the set of SCI message protocol support that
provide us with this capability.
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since v3: none
V3: https://patchwork.kernel.org/patch/9317841/
drivers/firmware/ti_sci.c | 685 +++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 289 ++++++++++++++
include/linux/soc/ti/ti_sci_protocol.h | 78 ++++
3 files changed, 1052 insertions(+)
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index c7b25ccf6f07..496a007e5c69 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -902,6 +902,675 @@ static int ti_sci_cmd_get_device_resets(const struct ti_sci_handle *handle,
NULL);
}
+/**
+ * ti_sci_set_clock_state() - Set clock state helper
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @flags: Header flags as needed
+ * @state: State to request for the clock.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_set_clock_state(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id,
+ u32 flags, u8 state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_clock_state *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_CLOCK_STATE,
+ flags | TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_clock_state *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->request_state = state;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_clock_state() - Get clock state helper
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @programmed_state: State requested for clock to move to
+ * @current_state: State that the clock is currently in
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_get_clock_state(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id,
+ u8 *programmed_state, u8 *current_state)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_state *req;
+ struct ti_sci_msg_resp_get_clock_state *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ if (!programmed_state && !current_state)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_CLOCK_STATE,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_state *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_state *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp)) {
+ ret = -ENODEV;
+ goto fail;
+ }
+
+ if (programmed_state)
+ *programmed_state = resp->programmed_state;
+ if (current_state)
+ *current_state = resp->current_state;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_get_clock() - Get control of a clock from TI SCI
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @needs_ssc: 'true' if Spread Spectrum clock is desired, else 'false'
+ * @can_change_freq: 'true' if frequency change is desired, else 'false'
+ * @enable_input_term: 'true' if input termination is desired, else 'false'
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_get_clock(const struct ti_sci_handle *handle, u32 dev_id,
+ u8 clk_id, bool needs_ssc, bool can_change_freq,
+ bool enable_input_term)
+{
+ u32 flags = 0;
+
+ flags |= needs_ssc ? MSG_FLAG_CLOCK_ALLOW_SSC : 0;
+ flags |= can_change_freq ? MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE : 0;
+ flags |= enable_input_term ? MSG_FLAG_CLOCK_INPUT_TERM : 0;
+
+ return ti_sci_set_clock_state(handle, dev_id, clk_id, flags,
+ MSG_CLOCK_SW_STATE_REQ);
+}
+
+/**
+ * ti_sci_cmd_idle_clock() - Idle a clock which is in our control
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ *
+ * NOTE: This clock must have been requested by get_clock previously.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_idle_clock(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id)
+{
+ return ti_sci_set_clock_state(handle, dev_id, clk_id, 0,
+ MSG_CLOCK_SW_STATE_UNREQ);
+}
+
+/**
+ * ti_sci_cmd_put_clock() - Release a clock from our control back to TISCI
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ *
+ * NOTE: This clock must have been requested by get_clock previously.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_put_clock(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id)
+{
+ return ti_sci_set_clock_state(handle, dev_id, clk_id, 0,
+ MSG_CLOCK_SW_STATE_AUTO);
+}
+
+/**
+ * ti_sci_cmd_clk_is_auto() - Is the clock being auto managed
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @req_state: state indicating if the clock is auto managed
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_is_auto(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, bool *req_state)
+{
+ u8 state = 0;
+ int ret;
+
+ if (!req_state)
+ return -EINVAL;
+
+ ret = ti_sci_cmd_get_clock_state(handle, dev_id, clk_id, &state, NULL);
+ if (ret)
+ return ret;
+
+ *req_state = (state == MSG_CLOCK_SW_STATE_AUTO);
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_clk_is_on() - Is the clock ON
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @req_state: state indicating if the clock is managed by us and enabled
+ * @curr_state: state indicating if the clock is ready for operation
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_is_on(const struct ti_sci_handle *handle, u32 dev_id,
+ u8 clk_id, bool *req_state, bool *curr_state)
+{
+ u8 c_state = 0, r_state = 0;
+ int ret;
+
+ if (!req_state && !curr_state)
+ return -EINVAL;
+
+ ret = ti_sci_cmd_get_clock_state(handle, dev_id, clk_id,
+ &r_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (req_state)
+ *req_state = (r_state == MSG_CLOCK_SW_STATE_REQ);
+ if (curr_state)
+ *curr_state = (c_state == MSG_CLOCK_HW_STATE_READY);
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_clk_is_off() - Is the clock OFF
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @req_state: state indicating if the clock is managed by us and disabled
+ * @curr_state: state indicating if the clock is NOT ready for operation
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_is_off(const struct ti_sci_handle *handle, u32 dev_id,
+ u8 clk_id, bool *req_state, bool *curr_state)
+{
+ u8 c_state = 0, r_state = 0;
+ int ret;
+
+ if (!req_state && !curr_state)
+ return -EINVAL;
+
+ ret = ti_sci_cmd_get_clock_state(handle, dev_id, clk_id,
+ &r_state, &c_state);
+ if (ret)
+ return ret;
+
+ if (req_state)
+ *req_state = (r_state == MSG_CLOCK_SW_STATE_UNREQ);
+ if (curr_state)
+ *curr_state = (c_state == MSG_CLOCK_HW_STATE_NOT_READY);
+ return 0;
+}
+
+/**
+ * ti_sci_cmd_clk_set_parent() - Set the clock source of a specific device clock
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @parent_id: Parent clock identifier to set
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_set_parent(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u8 parent_id)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_clock_parent *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_CLOCK_PARENT,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_clock_parent *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->parent_id = parent_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_parent() - Get current parent clock source
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @parent_id: Current clock parent
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_parent(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u8 *parent_id)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_parent *req;
+ struct ti_sci_msg_resp_get_clock_parent *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !parent_id)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_CLOCK_PARENT,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_parent *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_parent *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *parent_id = resp->parent_id;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_num_parents() - Get num parents of the current clk source
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @num_parents: Returns he number of parents to the current clock.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_num_parents(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id,
+ u8 *num_parents)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_num_parents *req;
+ struct ti_sci_msg_resp_get_clock_num_parents *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !num_parents)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_NUM_CLOCK_PARENTS,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_num_parents *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_num_parents *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *num_parents = resp->num_parents;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_match_freq() - Find a good match for frequency
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @min_freq: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq: The target clock frequency in Hz. A frequency will be
+ * processed as close to this target frequency as possible.
+ * @max_freq: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @match_freq: Frequency match in Hz response.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_match_freq(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u64 min_freq,
+ u64 target_freq, u64 max_freq,
+ u64 *match_freq)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_query_clock_freq *req;
+ struct ti_sci_msg_resp_query_clock_freq *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !match_freq)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_QUERY_CLOCK_FREQ,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_query_clock_freq *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->min_freq_hz = min_freq;
+ req->target_freq_hz = target_freq;
+ req->max_freq_hz = max_freq;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_query_clock_freq *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *match_freq = resp->freq_hz;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_set_freq() - Set a frequency for clock
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @min_freq: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq: The target clock frequency in Hz. A frequency will be
+ * processed as close to this target frequency as possible.
+ * @max_freq: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_set_freq(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u64 min_freq,
+ u64 target_freq, u64 max_freq)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_set_clock_freq *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SET_CLOCK_FREQ,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_set_clock_freq *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+ req->min_freq_hz = min_freq;
+ req->target_freq_hz = target_freq;
+ req->max_freq_hz = max_freq;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ ret = ti_sci_is_response_ack(resp) ? 0 : -ENODEV;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
+/**
+ * ti_sci_cmd_clk_get_freq() - Get current frequency
+ * @handle: pointer to TI SCI handle
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @freq: Currently frequency in Hz
+ *
+ * Return: 0 if all went well, else returns appropriate error value.
+ */
+static int ti_sci_cmd_clk_get_freq(const struct ti_sci_handle *handle,
+ u32 dev_id, u8 clk_id, u64 *freq)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_get_clock_freq *req;
+ struct ti_sci_msg_resp_get_clock_freq *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle || !freq)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_GET_CLOCK_FREQ,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_get_clock_freq *)xfer->xfer_buf;
+ req->dev_id = dev_id;
+ req->clk_id = clk_id;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_resp_get_clock_freq *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ *freq = resp->freq_hz;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
/*
* ti_sci_setup_ops() - Setup the operations structures
* @info: pointer to TISCI pointer
@@ -910,6 +1579,7 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
{
struct ti_sci_ops *ops = &info->handle.ops;
struct ti_sci_dev_ops *dops = &ops->dev_ops;
+ struct ti_sci_clk_ops *cops = &ops->clk_ops;
dops->get_device = ti_sci_cmd_get_device;
dops->idle_device = ti_sci_cmd_idle_device;
@@ -923,6 +1593,21 @@ static void ti_sci_setup_ops(struct ti_sci_info *info)
dops->is_transitioning = ti_sci_cmd_dev_is_trans;
dops->set_device_resets = ti_sci_cmd_set_device_resets;
dops->get_device_resets = ti_sci_cmd_get_device_resets;
+
+ cops->get_clock = ti_sci_cmd_get_clock;
+ cops->idle_clock = ti_sci_cmd_idle_clock;
+ cops->put_clock = ti_sci_cmd_put_clock;
+ cops->is_auto = ti_sci_cmd_clk_is_auto;
+ cops->is_on = ti_sci_cmd_clk_is_on;
+ cops->is_off = ti_sci_cmd_clk_is_off;
+
+ cops->set_parent = ti_sci_cmd_clk_set_parent;
+ cops->get_parent = ti_sci_cmd_clk_get_parent;
+ cops->get_num_parents = ti_sci_cmd_clk_get_num_parents;
+
+ cops->get_best_match_freq = ti_sci_cmd_clk_get_match_freq;
+ cops->set_freq = ti_sci_cmd_clk_set_freq;
+ cops->get_freq = ti_sci_cmd_clk_get_freq;
}
/**
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index 29ce0532a7ca..f69907cfc128 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -52,6 +52,16 @@
#define TI_SCI_MSG_GET_DEVICE_STATE 0x0201
#define TI_SCI_MSG_SET_DEVICE_RESETS 0x0202
+/* Clock requests */
+#define TI_SCI_MSG_SET_CLOCK_STATE 0x0100
+#define TI_SCI_MSG_GET_CLOCK_STATE 0x0101
+#define TI_SCI_MSG_SET_CLOCK_PARENT 0x0102
+#define TI_SCI_MSG_GET_CLOCK_PARENT 0x0103
+#define TI_SCI_MSG_GET_NUM_CLOCK_PARENTS 0x0104
+#define TI_SCI_MSG_SET_CLOCK_FREQ 0x010c
+#define TI_SCI_MSG_QUERY_CLOCK_FREQ 0x010d
+#define TI_SCI_MSG_GET_CLOCK_FREQ 0x010e
+
/**
* struct ti_sci_msg_hdr - Generic Message Header for All messages and responses
* @type: Type of messages: One of TI_SCI_MSG* values
@@ -188,4 +198,283 @@ struct ti_sci_msg_req_set_device_resets {
u32 resets;
} __packed;
+/**
+ * struct ti_sci_msg_req_set_clock_state - Request to setup a Clock state
+ * @hdr: Generic Header, Certain flags can be set specific to the clocks:
+ * MSG_FLAG_CLOCK_ALLOW_SSC: Allow this clock to be modified
+ * via spread spectrum clocking.
+ * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE: Allow this clock's
+ * frequency to be changed while it is running so long as it
+ * is within the min/max limits.
+ * MSG_FLAG_CLOCK_INPUT_TERM: Enable input termination, this
+ * is only applicable to clock inputs on the SoC pseudo-device.
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @request_state: Request the state for the clock to be set to.
+ * MSG_CLOCK_SW_STATE_UNREQ: The IP does not require this clock,
+ * it can be disabled, regardless of the state of the device
+ * MSG_CLOCK_SW_STATE_AUTO: Allow the System Controller to
+ * automatically manage the state of this clock. If the device
+ * is enabled, then the clock is enabled. If the device is set
+ * to off or retention, then the clock is internally set as not
+ * being required by the device.(default)
+ * MSG_CLOCK_SW_STATE_REQ: Configure the clock to be enabled,
+ * regardless of the state of the device.
+ *
+ * Normally, all required clocks are managed by TISCI entity, this is used
+ * only for specific control *IF* required. Auto managed state is
+ * MSG_CLOCK_SW_STATE_AUTO, in other states, TISCI entity assume remote
+ * will explicitly control.
+ *
+ * Request type is TI_SCI_MSG_SET_CLOCK_STATE, response is a generic
+ * ACK or NACK message.
+ */
+struct ti_sci_msg_req_set_clock_state {
+ /* Additional hdr->flags options */
+#define MSG_FLAG_CLOCK_ALLOW_SSC TI_SCI_MSG_FLAG(8)
+#define MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE TI_SCI_MSG_FLAG(9)
+#define MSG_FLAG_CLOCK_INPUT_TERM TI_SCI_MSG_FLAG(10)
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+#define MSG_CLOCK_SW_STATE_UNREQ 0
+#define MSG_CLOCK_SW_STATE_AUTO 1
+#define MSG_CLOCK_SW_STATE_REQ 2
+ u8 request_state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_state - Request for clock state
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to get state of.
+ *
+ * Request type is TI_SCI_MSG_GET_CLOCK_STATE, response is state
+ * of the clock
+ */
+struct ti_sci_msg_req_get_clock_state {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_state - Response to get clock state
+ * @hdr: Generic Header
+ * @programmed_state: Any programmed state of the clock. This is one of
+ * MSG_CLOCK_SW_STATE* values.
+ * @current_state: Current state of the clock. This is one of:
+ * MSG_CLOCK_HW_STATE_NOT_READY: Clock is not ready
+ * MSG_CLOCK_HW_STATE_READY: Clock is ready
+ *
+ * Response to TI_SCI_MSG_GET_CLOCK_STATE.
+ */
+struct ti_sci_msg_resp_get_clock_state {
+ struct ti_sci_msg_hdr hdr;
+ u8 programmed_state;
+#define MSG_CLOCK_HW_STATE_NOT_READY 0
+#define MSG_CLOCK_HW_STATE_READY 1
+ u8 current_state;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_set_clock_parent - Set the clock parent
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * @parent_id: The new clock parent is selectable by an index via this
+ * parameter.
+ *
+ * Request type is TI_SCI_MSG_SET_CLOCK_PARENT, response is generic
+ * ACK / NACK message.
+ */
+struct ti_sci_msg_req_set_clock_parent {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+ u8 parent_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_parent - Get the clock parent
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to get the parent for.
+ *
+ * Request type is TI_SCI_MSG_GET_CLOCK_PARENT, response is parent information
+ */
+struct ti_sci_msg_req_get_clock_parent {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_parent - Response with clock parent
+ * @hdr: Generic Header
+ * @parent_id: The current clock parent
+ *
+ * Response to TI_SCI_MSG_GET_CLOCK_PARENT.
+ */
+struct ti_sci_msg_resp_get_clock_parent {
+ struct ti_sci_msg_hdr hdr;
+ u8 parent_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_num_parents - Request to get clock parents
+ * @hdr: Generic header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * This request provides information about how many clock parent options
+ * are available for a given clock to a device. This is typically used
+ * for input clocks.
+ *
+ * Request type is TI_SCI_MSG_GET_NUM_CLOCK_PARENTS, response is appropriate
+ * message, or NACK in case of inability to satisfy request.
+ */
+struct ti_sci_msg_req_get_clock_num_parents {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_num_parents - Response for get clk parents
+ * @hdr: Generic header
+ * @num_parents: Number of clock parents
+ *
+ * Response to TI_SCI_MSG_GET_NUM_CLOCK_PARENTS
+ */
+struct ti_sci_msg_resp_get_clock_num_parents {
+ struct ti_sci_msg_hdr hdr;
+ u8 num_parents;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_query_clock_freq - Request to query a frequency
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq_hz: The target clock frequency. A frequency will be found
+ * as close to this target frequency as possible.
+ * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * NOTE: Normally clock frequency management is automatically done by TISCI
+ * entity. In case of specific requests, TISCI evaluates capability to achieve
+ * requested frequency within provided range and responds with
+ * result message.
+ *
+ * Request type is TI_SCI_MSG_QUERY_CLOCK_FREQ, response is appropriate message,
+ * or NACK in case of inability to satisfy request.
+ */
+struct ti_sci_msg_req_query_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u64 min_freq_hz;
+ u64 target_freq_hz;
+ u64 max_freq_hz;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_query_clock_freq - Response to a clock frequency query
+ * @hdr: Generic Header
+ * @freq_hz: Frequency that is the best match in Hz.
+ *
+ * Response to request type TI_SCI_MSG_QUERY_CLOCK_FREQ. NOTE: if the request
+ * cannot be satisfied, the message will be of type NACK.
+ */
+struct ti_sci_msg_resp_query_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u64 freq_hz;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_set_clock_freq - Request to setup a clock frequency
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @min_freq_hz: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @target_freq_hz: The target clock frequency. The clock will be programmed
+ * at a rate as close to this target frequency as possible.
+ * @max_freq_hz: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * NOTE: Normally clock frequency management is automatically done by TISCI
+ * entity. In case of specific requests, TISCI evaluates capability to achieve
+ * requested range and responds with success/failure message.
+ *
+ * This sets the desired frequency for a clock within an allowable
+ * range. This message will fail on an enabled clock unless
+ * MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE is set for the clock. Additionally,
+ * if other clocks have their frequency modified due to this message,
+ * they also must have the MSG_FLAG_CLOCK_ALLOW_FREQ_CHANGE or be disabled.
+ *
+ * Calling set frequency on a clock input to the SoC pseudo-device will
+ * inform the PMMC of that clock's frequency. Setting a frequency of
+ * zero will indicate the clock is disabled.
+ *
+ * Calling set frequency on clock outputs from the SoC pseudo-device will
+ * function similarly to setting the clock frequency on a device.
+ *
+ * Request type is TI_SCI_MSG_SET_CLOCK_FREQ, response is a generic ACK/NACK
+ * message.
+ */
+struct ti_sci_msg_req_set_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u64 min_freq_hz;
+ u64 target_freq_hz;
+ u64 max_freq_hz;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_req_get_clock_freq - Request to get the clock frequency
+ * @hdr: Generic Header
+ * @dev_id: Device identifier this request is for
+ * @clk_id: Clock identifier for the device for this request.
+ *
+ * NOTE: Normally clock frequency management is automatically done by TISCI
+ * entity. In some cases, clock frequencies are configured by host.
+ *
+ * Request type is TI_SCI_MSG_GET_CLOCK_FREQ, responded with clock frequency
+ * that the clock is currently at.
+ */
+struct ti_sci_msg_req_get_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u32 dev_id;
+ u8 clk_id;
+} __packed;
+
+/**
+ * struct ti_sci_msg_resp_get_clock_freq - Response of clock frequency request
+ * @hdr: Generic Header
+ * @freq_hz: Frequency that the clock is currently on, in Hz.
+ *
+ * Response to request type TI_SCI_MSG_GET_CLOCK_FREQ.
+ */
+struct ti_sci_msg_resp_get_clock_freq {
+ struct ti_sci_msg_hdr hdr;
+ u64 freq_hz;
+} __packed;
+
#endif /* __TI_SCI_H */
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 87fa73851471..76378fddf609 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -115,11 +115,89 @@ struct ti_sci_dev_ops {
};
/**
+ * struct ti_sci_clk_ops - Clock control operations
+ * @get_clock: Request for activation of clock and manage by processor
+ * - needs_ssc: 'true' if Spread Spectrum clock is desired.
+ * - can_change_freq: 'true' if frequency change is desired.
+ * - enable_input_term: 'true' if input termination is desired.
+ * @idle_clock: Request for Idling a clock managed by processor
+ * @put_clock: Release the clock to be auto managed by TISCI
+ * @is_auto: Is the clock being auto managed
+ * - req_state: state indicating if the clock is auto managed
+ * @is_on: Is the clock ON
+ * - req_state: if the clock is requested to be forced ON
+ * - current_state: if the clock is currently ON
+ * @is_off: Is the clock OFF
+ * - req_state: if the clock is requested to be forced OFF
+ * - current_state: if the clock is currently Gated
+ * @set_parent: Set the clock source of a specific device clock
+ * - parent_id: Parent clock identifier to set.
+ * @get_parent: Get the current clock source of a specific device clock
+ * - parent_id: Parent clock identifier which is the parent.
+ * @get_num_parents: Get the number of parents of the current clock source
+ * - num_parents: returns the number of parent clocks.
+ * @get_best_match_freq: Find a best matching frequency for a frequency
+ * range.
+ * - match_freq: Best matching frequency in Hz.
+ * @set_freq: Set the Clock frequency
+ * @get_freq: Get the Clock frequency
+ * - current_freq: Frequency in Hz that the clock is at.
+ *
+ * NOTE: for all these functions, the following parameters are generic in
+ * nature:
+ * -handle: Pointer to TISCI handle as retrieved by *ti_sci_get_handle
+ * -did: Device identifier this request is for
+ * -cid: Clock identifier for the device for this request.
+ * Each device has it's own set of clock inputs. This indexes
+ * which clock input to modify.
+ * -min_freq: The minimum allowable frequency in Hz. This is the minimum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ * -target_freq: The target clock frequency in Hz. A frequency will be
+ * processed as close to this target frequency as possible.
+ * -max_freq: The maximum allowable frequency in Hz. This is the maximum
+ * allowable programmed frequency and does not account for clock
+ * tolerances and jitter.
+ *
+ * Request for the clock - NOTE: the client MUST maintain integrity of
+ * usage count by balancing get_clock with put_clock. No refcounting is
+ * managed by driver for that purpose.
+ */
+struct ti_sci_clk_ops {
+ int (*get_clock)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool needs_ssc, bool can_change_freq,
+ bool enable_input_term);
+ int (*idle_clock)(const struct ti_sci_handle *handle, u32 did, u8 cid);
+ int (*put_clock)(const struct ti_sci_handle *handle, u32 did, u8 cid);
+ int (*is_auto)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool *req_state);
+ int (*is_on)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool *req_state, bool *current_state);
+ int (*is_off)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ bool *req_state, bool *current_state);
+ int (*set_parent)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u8 parent_id);
+ int (*get_parent)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u8 *parent_id);
+ int (*get_num_parents)(const struct ti_sci_handle *handle, u32 did,
+ u8 cid, u8 *num_parents);
+ int (*get_best_match_freq)(const struct ti_sci_handle *handle, u32 did,
+ u8 cid, u64 min_freq, u64 target_freq,
+ u64 max_freq, u64 *match_freq);
+ int (*set_freq)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u64 min_freq, u64 target_freq, u64 max_freq);
+ int (*get_freq)(const struct ti_sci_handle *handle, u32 did, u8 cid,
+ u64 *current_freq);
+};
+
+/**
* struct ti_sci_ops - Function support for TI SCI
* @dev_ops: Device specific operations
+ * @clk_ops: Clock specific operations
*/
struct ti_sci_ops {
struct ti_sci_dev_ops dev_ops;
+ struct ti_sci_clk_ops clk_ops;
};
/**
--
2.10.0
^ permalink raw reply related
* [PATCH V4 5/5] firmware: ti_sci: Add support for reboot core service
From: Nishanth Menon @ 2016-10-18 23:08 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161018230837.6515-1-nm@ti.com>
Since system controller now has control over SoC power management, it
needs to be explicitly requested to reboot the SoC. Add support for
it.
In some systems however, SoC needs to toggle a GPIO or send event to an
external entity (like a PMIC) for a system reboot to take place. To
facilitate that, we allow for a DT property to determine if the reboot
handler will be registered and further, the service is also made
available to other drivers (such as PMIC driver) to sequence the
additional operation and trigger the SoC reboot as the last step.
Tested-by: Lokesh Vutla <lokeshvutla@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
---
Changes since V3:
- checkpatch fixes for macro after checkpatch.pl update in v4.9-rc1
V3: https://patchwork.kernel.org/patch/9317837/
drivers/firmware/ti_sci.c | 83 ++++++++++++++++++++++++++++++++++
drivers/firmware/ti_sci.h | 12 +++++
include/linux/soc/ti/ti_sci_protocol.h | 11 +++++
3 files changed, 106 insertions(+)
diff --git a/drivers/firmware/ti_sci.c b/drivers/firmware/ti_sci.c
index 496a007e5c69..874ff32db366 100644
--- a/drivers/firmware/ti_sci.c
+++ b/drivers/firmware/ti_sci.c
@@ -28,6 +28,7 @@
#include <linux/slab.h>
#include <linux/soc/ti/ti-msgmgr.h>
#include <linux/soc/ti/ti_sci_protocol.h>
+#include <linux/reboot.h>
#include "ti_sci.h"
@@ -90,6 +91,7 @@ struct ti_sci_desc {
* struct ti_sci_info - Structure representing a TI SCI instance
* @dev: Device pointer
* @desc: SoC description for this instance
+ * @nb: Reboot Notifier block
* @d: Debugfs file entry
* @debug_region: Memory region where the debug message are available
* @debug_region_size: Debug region size
@@ -104,6 +106,7 @@ struct ti_sci_desc {
*/
struct ti_sci_info {
struct device *dev;
+ struct notifier_block nb;
const struct ti_sci_desc *desc;
struct dentry *d;
void __iomem *debug_region;
@@ -117,10 +120,12 @@ struct ti_sci_info {
struct list_head node;
/* protected by ti_sci_list_mutex */
int users;
+
};
#define cl_to_ti_sci_info(c) container_of(c, struct ti_sci_info, cl)
#define handle_to_ti_sci_info(h) container_of(h, struct ti_sci_info, handle)
+#define reboot_to_ti_sci_info(n) container_of(n, struct ti_sci_info, nb)
#ifdef CONFIG_DEBUG_FS
@@ -1571,6 +1576,52 @@ static int ti_sci_cmd_clk_get_freq(const struct ti_sci_handle *handle,
return ret;
}
+static int ti_sci_cmd_core_reboot(const struct ti_sci_handle *handle)
+{
+ struct ti_sci_info *info;
+ struct ti_sci_msg_req_reboot *req;
+ struct ti_sci_msg_hdr *resp;
+ struct ti_sci_xfer *xfer;
+ struct device *dev;
+ int ret = 0;
+
+ if (IS_ERR(handle))
+ return PTR_ERR(handle);
+ if (!handle)
+ return -EINVAL;
+
+ info = handle_to_ti_sci_info(handle);
+ dev = info->dev;
+
+ xfer = ti_sci_get_one_xfer(info, TI_SCI_MSG_SYS_RESET,
+ TI_SCI_FLAG_REQ_ACK_ON_PROCESSED,
+ sizeof(*req), sizeof(*resp));
+ if (IS_ERR(xfer)) {
+ ret = PTR_ERR(xfer);
+ dev_err(dev, "Message alloc failed(%d)\n", ret);
+ return ret;
+ }
+ req = (struct ti_sci_msg_req_reboot *)xfer->xfer_buf;
+
+ ret = ti_sci_do_xfer(info, xfer);
+ if (ret) {
+ dev_err(dev, "Mbox send fail %d\n", ret);
+ goto fail;
+ }
+
+ resp = (struct ti_sci_msg_hdr *)xfer->xfer_buf;
+
+ if (!ti_sci_is_response_ack(resp))
+ ret = -ENODEV;
+ else
+ ret = 0;
+
+fail:
+ ti_sci_put_one_xfer(&info->minfo, xfer);
+
+ return ret;
+}
+
/*
* ti_sci_setup_ops() - Setup the operations structures
* @info: pointer to TISCI pointer
@@ -1578,9 +1629,12 @@ static int ti_sci_cmd_clk_get_freq(const struct ti_sci_handle *handle,
static void ti_sci_setup_ops(struct ti_sci_info *info)
{
struct ti_sci_ops *ops = &info->handle.ops;
+ struct ti_sci_core_ops *core_ops = &ops->core_ops;
struct ti_sci_dev_ops *dops = &ops->dev_ops;
struct ti_sci_clk_ops *cops = &ops->clk_ops;
+ core_ops->reboot_device = ti_sci_cmd_core_reboot;
+
dops->get_device = ti_sci_cmd_get_device;
dops->idle_device = ti_sci_cmd_idle_device;
dops->put_device = ti_sci_cmd_put_device;
@@ -1732,6 +1786,18 @@ const struct ti_sci_handle *devm_ti_sci_get_handle(struct device *dev)
}
EXPORT_SYMBOL_GPL(devm_ti_sci_get_handle);
+static int tisci_reboot_handler(struct notifier_block *nb, unsigned long mode,
+ void *cmd)
+{
+ struct ti_sci_info *info = reboot_to_ti_sci_info(nb);
+ const struct ti_sci_handle *handle = &info->handle;
+
+ ti_sci_cmd_core_reboot(handle);
+
+ /* call fail OR pass, we should not be here in the first place */
+ return NOTIFY_BAD;
+}
+
/* Description for K2G */
static const struct ti_sci_desc ti_sci_pmmc_k2g_desc = {
.host_id = 2,
@@ -1759,6 +1825,7 @@ static int ti_sci_probe(struct platform_device *pdev)
struct mbox_client *cl;
int ret = -EINVAL;
int i;
+ int reboot = 0;
of_id = of_match_device(ti_sci_of_match, dev);
if (!of_id) {
@@ -1773,6 +1840,8 @@ static int ti_sci_probe(struct platform_device *pdev)
info->dev = dev;
info->desc = desc;
+ reboot = of_property_read_bool(dev->of_node,
+ "ti,system-reboot-controller");
INIT_LIST_HEAD(&info->node);
minfo = &info->minfo;
@@ -1845,6 +1914,17 @@ static int ti_sci_probe(struct platform_device *pdev)
ti_sci_setup_ops(info);
+ if (reboot) {
+ info->nb.notifier_call = tisci_reboot_handler;
+ info->nb.priority = 128;
+
+ ret = register_restart_handler(&info->nb);
+ if (ret) {
+ dev_err(dev, "reboot registration fail(%d)\n", ret);
+ return ret;
+ }
+ }
+
dev_info(dev, "ABI: %d.%d (firmware rev 0x%04x '%s')\n",
info->handle.version.abi_major, info->handle.version.abi_minor,
info->handle.version.firmware_revision,
@@ -1874,6 +1954,9 @@ static int ti_sci_remove(struct platform_device *pdev)
info = platform_get_drvdata(pdev);
+ if (info->nb.notifier_call)
+ unregister_restart_handler(&info->nb);
+
mutex_lock(&ti_sci_list_mutex);
if (info->users)
ret = -EBUSY;
diff --git a/drivers/firmware/ti_sci.h b/drivers/firmware/ti_sci.h
index f69907cfc128..9b611e9e6f6d 100644
--- a/drivers/firmware/ti_sci.h
+++ b/drivers/firmware/ti_sci.h
@@ -46,6 +46,7 @@
#define TI_SCI_MSG_VERSION 0x0002
#define TI_SCI_MSG_WAKE_REASON 0x0003
#define TI_SCI_MSG_GOODBYE 0x0004
+#define TI_SCI_MSG_SYS_RESET 0x0005
/* Device requests */
#define TI_SCI_MSG_SET_DEVICE_STATE 0x0200
@@ -106,6 +107,17 @@ struct ti_sci_msg_resp_version {
} __packed;
/**
+ * struct ti_sci_msg_req_reboot - Reboot the SoC
+ * @hdr: Generic Header
+ *
+ * Request type is TI_SCI_MSG_SYS_RESET, responded with a generic
+ * ACK/NACK message.
+ */
+struct ti_sci_msg_req_reboot {
+ struct ti_sci_msg_hdr hdr;
+} __packed;
+
+/**
* struct ti_sci_msg_req_set_device_state - Set the desired state of the device
* @hdr: Generic header
* @id: Indicates which device to modify
diff --git a/include/linux/soc/ti/ti_sci_protocol.h b/include/linux/soc/ti/ti_sci_protocol.h
index 76378fddf609..0ccbc138c26a 100644
--- a/include/linux/soc/ti/ti_sci_protocol.h
+++ b/include/linux/soc/ti/ti_sci_protocol.h
@@ -36,6 +36,16 @@ struct ti_sci_version_info {
struct ti_sci_handle;
/**
+ * struct ti_sci_core_ops - SoC Core Operations
+ * @reboot_device: Reboot the SoC
+ * Returns 0 for successful request(ideally should never return),
+ * else returns corresponding error value.
+ */
+struct ti_sci_core_ops {
+ int (*reboot_device)(const struct ti_sci_handle *handle);
+};
+
+/**
* struct ti_sci_dev_ops - Device control operations
* @get_device: Command to request for device managed by TISCI
* Returns 0 for successful exclusive request, else returns
@@ -196,6 +206,7 @@ struct ti_sci_clk_ops {
* @clk_ops: Clock specific operations
*/
struct ti_sci_ops {
+ struct ti_sci_core_ops core_ops;
struct ti_sci_dev_ops dev_ops;
struct ti_sci_clk_ops clk_ops;
};
--
2.10.0
^ permalink raw reply related
* [PATCH] media: s5p-mfc collapse two error message into one
From: Shuah Khan @ 2016-10-18 23:28 UTC (permalink / raw)
To: linux-arm-kernel
s5p_mfc_alloc_priv_buf() prints two message to report invalid memory
configuration error. Collapse them into a single message.
Signed-off-by: Shuah Khan <shuahkh@osg.samsung.com>
---
drivers/media/platform/s5p-mfc/s5p_mfc_opr.c | 3 +--
1 file changed, 1 insertion(+), 2 deletions(-)
diff --git a/drivers/media/platform/s5p-mfc/s5p_mfc_opr.c b/drivers/media/platform/s5p-mfc/s5p_mfc_opr.c
index eee16a1..44d2325 100644
--- a/drivers/media/platform/s5p-mfc/s5p_mfc_opr.c
+++ b/drivers/media/platform/s5p-mfc/s5p_mfc_opr.c
@@ -49,8 +49,7 @@ int s5p_mfc_alloc_priv_buf(struct device *dev, dma_addr_t base,
}
if (b->dma < base) {
- mfc_err("Invaling memory configuration!\n");
- mfc_err("Allocated buffer (%pad) is lower than memory base address (%pad)\n",
+ mfc_err("Invalid memory configuration - buffer (%pad) is below base memory address(%pad)\n",
&b->dma, &base);
dma_free_coherent(dev, b->size, b->virt, b->dma);
return -ENOMEM;
--
2.7.4
^ permalink raw reply related
* [PATCH/RESEND] thermal: qcom-spmi: Treat reg property as a single cell
From: Stephen Boyd @ 2016-10-18 23:40 UTC (permalink / raw)
To: linux-arm-kernel
We only read the first element of the reg property to figure out
the offset of the temperature sensor inside the PMIC.
Furthermore, we want to remove the second element in DT, so just
don't read the second element so that probe keeps working if we
change the DT in the future.
Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
This was sent in January of this year but hasn't been picked up.
drivers/thermal/qcom-spmi-temp-alarm.c | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/thermal/qcom-spmi-temp-alarm.c b/drivers/thermal/qcom-spmi-temp-alarm.c
index 819c6d5d7aa7..f50241962ad2 100644
--- a/drivers/thermal/qcom-spmi-temp-alarm.c
+++ b/drivers/thermal/qcom-spmi-temp-alarm.c
@@ -200,7 +200,7 @@ static int qpnp_tm_probe(struct platform_device *pdev)
struct qpnp_tm_chip *chip;
struct device_node *node;
u8 type, subtype;
- u32 res[2];
+ u32 res;
int ret, irq;
node = pdev->dev.of_node;
@@ -215,7 +215,7 @@ static int qpnp_tm_probe(struct platform_device *pdev)
if (!chip->map)
return -ENXIO;
- ret = of_property_read_u32_array(node, "reg", res, 2);
+ ret = of_property_read_u32(node, "reg", &res);
if (ret < 0)
return ret;
@@ -228,7 +228,7 @@ static int qpnp_tm_probe(struct platform_device *pdev)
if (PTR_ERR(chip->adc) == -EPROBE_DEFER)
return PTR_ERR(chip->adc);
- chip->base = res[0];
+ chip->base = res;
ret = qpnp_tm_read(chip, QPNP_TM_REG_TYPE, &type);
if (ret < 0) {
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH/RESEND] recordmcount: arm: Implement make_nop
From: Stephen Boyd @ 2016-10-18 23:42 UTC (permalink / raw)
To: linux-arm-kernel
In similar spirit to x86 and arm64 support, add a make_nop_arm()
to replace calls to mcount with a nop in sections that aren't
traced.
Cc: Russell King <linux@arm.linux.org.uk>
Acked-by: Rabin Vincent <rabin@rab.in>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
scripts/recordmcount.c | 65 ++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 65 insertions(+)
diff --git a/scripts/recordmcount.c b/scripts/recordmcount.c
index 5423a58d1b06..aeb34223167c 100644
--- a/scripts/recordmcount.c
+++ b/scripts/recordmcount.c
@@ -213,6 +213,59 @@ static int make_nop_x86(void *map, size_t const offset)
return 0;
}
+static unsigned char ideal_nop4_arm_le[4] = { 0x00, 0x00, 0xa0, 0xe1 }; /* mov r0, r0 */
+static unsigned char ideal_nop4_arm_be[4] = { 0xe1, 0xa0, 0x00, 0x00 }; /* mov r0, r0 */
+static unsigned char *ideal_nop4_arm;
+
+static unsigned char bl_mcount_arm_le[4] = { 0xfe, 0xff, 0xff, 0xeb }; /* bl */
+static unsigned char bl_mcount_arm_be[4] = { 0xeb, 0xff, 0xff, 0xfe }; /* bl */
+static unsigned char *bl_mcount_arm;
+
+static unsigned char push_arm_le[4] = { 0x04, 0xe0, 0x2d, 0xe5 }; /* push {lr} */
+static unsigned char push_arm_be[4] = { 0xe5, 0x2d, 0xe0, 0x04 }; /* push {lr} */
+static unsigned char *push_arm;
+
+static unsigned char ideal_nop2_thumb_le[2] = { 0x00, 0xbf }; /* nop */
+static unsigned char ideal_nop2_thumb_be[2] = { 0xbf, 0x00 }; /* nop */
+static unsigned char *ideal_nop2_thumb;
+
+static unsigned char push_bl_mcount_thumb_le[6] = { 0x00, 0xb5, 0xff, 0xf7, 0xfe, 0xff }; /* push {lr}, bl */
+static unsigned char push_bl_mcount_thumb_be[6] = { 0xb5, 0x00, 0xf7, 0xff, 0xff, 0xfe }; /* push {lr}, bl */
+static unsigned char *push_bl_mcount_thumb;
+
+static int make_nop_arm(void *map, size_t const offset)
+{
+ char *ptr;
+ int cnt = 1;
+ int nop_size;
+ size_t off = offset;
+
+ ptr = map + offset;
+ if (memcmp(ptr, bl_mcount_arm, 4) == 0) {
+ if (memcmp(ptr - 4, push_arm, 4) == 0) {
+ off -= 4;
+ cnt = 2;
+ }
+ ideal_nop = ideal_nop4_arm;
+ nop_size = 4;
+ } else if (memcmp(ptr - 2, push_bl_mcount_thumb, 6) == 0) {
+ cnt = 3;
+ nop_size = 2;
+ off -= 2;
+ ideal_nop = ideal_nop2_thumb;
+ } else
+ return -1;
+
+ /* Convert to nop */
+ ulseek(fd_map, off, SEEK_SET);
+
+ do {
+ uwrite(fd_map, ideal_nop, nop_size);
+ } while (--cnt > 0);
+
+ return 0;
+}
+
static unsigned char ideal_nop4_arm64[4] = {0x1f, 0x20, 0x03, 0xd5};
static int make_nop_arm64(void *map, size_t const offset)
{
@@ -430,6 +483,11 @@ do_file(char const *const fname)
w2 = w2rev;
w8 = w8rev;
}
+ ideal_nop4_arm = ideal_nop4_arm_le;
+ bl_mcount_arm = bl_mcount_arm_le;
+ push_arm = push_arm_le;
+ ideal_nop2_thumb = ideal_nop2_thumb_le;
+ push_bl_mcount_thumb = push_bl_mcount_thumb_le;
break;
case ELFDATA2MSB:
if (*(unsigned char const *)&endian != 0) {
@@ -438,6 +496,11 @@ do_file(char const *const fname)
w2 = w2rev;
w8 = w8rev;
}
+ ideal_nop4_arm = ideal_nop4_arm_be;
+ bl_mcount_arm = bl_mcount_arm_be;
+ push_arm = push_arm_be;
+ ideal_nop2_thumb = ideal_nop2_thumb_be;
+ push_bl_mcount_thumb = push_bl_mcount_thumb_be;
break;
} /* end switch */
if (memcmp(ELFMAG, ehdr->e_ident, SELFMAG) != 0
@@ -463,6 +526,8 @@ do_file(char const *const fname)
break;
case EM_ARM: reltype = R_ARM_ABS32;
altmcount = "__gnu_mcount_nc";
+ make_nop = make_nop_arm;
+ rel_type_nop = R_ARM_NONE;
break;
case EM_AARCH64:
reltype = R_AARCH64_ABS64;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH/RESEND] clocksource/arm_arch_timer: Map frame with of_io_request_and_map()
From: Stephen Boyd @ 2016-10-18 23:45 UTC (permalink / raw)
To: linux-arm-kernel
Let's use the of_io_request_and_map() API so that the frame
region is protected and shows up in /proc/iomem.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
---
drivers/clocksource/arm_arch_timer.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/clocksource/arm_arch_timer.c b/drivers/clocksource/arm_arch_timer.c
index 73c487da6d2a..cbfa3bc5be75 100644
--- a/drivers/clocksource/arm_arch_timer.c
+++ b/drivers/clocksource/arm_arch_timer.c
@@ -964,7 +964,8 @@ static int __init arch_timer_mem_init(struct device_node *np)
}
ret= -ENXIO;
- base = arch_counter_base = of_iomap(best_frame, 0);
+ base = arch_counter_base = of_io_request_and_map(best_frame, 0,
+ "arch_mem_timer");
if (!base) {
pr_err("arch_timer: Can't map frame's registers\n");
goto out;
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related
* [PATCH v2 0/6] STM32F4 Add RTC & QSPI clocks
From: Stephen Boyd @ 2016-10-18 23:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476436699-21879-1-git-send-email-gabriel.fernandez@st.com>
On 10/14, gabriel.fernandez at st.com wrote:
>
> Gabriel Fernandez (6):
> clk: stm32f4: Add LSI & LSE clocks
> ARM: dts: stm32f429: add LSI and LSE clocks
> arm: stmf32: Enable SYSCON
> clk: stm32f4: Add RTC clock
> clk: stm32f469: Add QSPI clock
> ARM: dts: stm32f429: Add QSPI clock
Can the clk patches be picked without causing problems for
existing dt changes? Do you want an ack from clk maintainers
instead of us picking the clk patches up? The series has
intermingled clk and dts changes so I'm confused.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH 3/3] clk: imx6: Fix procedure to switch the parent of LDB_DI_CLK
From: Stephen Boyd @ 2016-10-19 0:01 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAOMZO5D7=A=ms_iq1D+Fgg4wKpRx-aScm5V=avxRPu62rFymzQ@mail.gmail.com>
On 09/23, Fabio Estevam wrote:
> Hi Stephen,
>
> On Fri, Sep 16, 2016 at 11:36 AM, Fabio Estevam <fabio.estevam@nxp.com> wrote:
> > Due to incorrect placement of the clock gate cell in the ldb_di[x]_clk
> > tree, the glitchy parent mux of ldb_di[x]_clk can cause a glitch to
> > enter the ldb_di_ipu_div divider. If the divider gets locked up, no
> > ldb_di[x]_clk is generated, and the LVDS display will hang when the
> > ipu_di_clk is sourced from ldb_di_clk.
> >
> > To fix the problem, both the new and current parent of the ldb_di_clk
> > should be disabled before the switch. This patch ensures that correct
> > steps are followed when ldb_di_clk parent is switched in the beginning
> > of boot. The glitchy muxes are then registered as read-only. The clock
> > parent can be selected using the assigned-clocks and
> > assigned-clock-parents properties of the ccm device tree node:
> >
> > &clks {
> > assigned-clocks = <&clks IMX6QDL_CLK_LDB_DI0_SEL>,
> > <&clks IMX6QDL_CLK_LDB_DI1_SEL>;
> > assigned-clock-parents = <&clks IMX6QDL_CLK_MMDC_CH1_AXI>,
> > <&clks IMX6QDL_CLK_PLL5_VIDEO_DIV>;
> > };
> >
> > The issue is explained in detail in EB821 ("LDB Clock Switch Procedure &
> > i.MX6 Asynchronous Clock Switching Guidelines") [1].
> >
> > [1] http://www.nxp.com/files/32bit/doc/eng_bulletin/EB821.pdf
> >
> > Signed-off-by: Ranjani Vaidyanathan <Ranjani.Vaidyanathan@nxp.com>
> > Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
> > Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
> > Reviewed-by: Akshay Bhat <akshay.bhat@timesys.com>
> > Tested-by Joshua Clayton <stillcompiling@gmail.com>
> > Tested-by: Charles Kang <Charles.Kang@advantech.com.tw>
> > Acked-by: Shawn Guo <shawnguo@kernel.org>
>
> Do you think this one could be applied to clk-next? It fixes an
> important LVDS bug.
>
Urgh, sorry I missed this one and then we got too close to the
merge window to keep applying things and I was traveling for a
bit. Is this a bug that's urgent and needs to be fixed to keep
these boards working in the v4.9-rc series? Does it need to go
back to stable? The change is fairly large, so we might be able
to put it into clk-fixes for -rc2, but it would need some
justification and preferably a stable/fixes tag.
Also, what about the other two patches in this series?
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH 3/3] clk: imx6: Fix procedure to switch the parent of LDB_DI_CLK
From: Fabio Estevam @ 2016-10-19 0:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161019000101.GQ8871@codeaurora.org>
Hi Stephen,
On Tue, Oct 18, 2016 at 10:01 PM, Stephen Boyd <sboyd@codeaurora.org> wrote:
> Urgh, sorry I missed this one and then we got too close to the
> merge window to keep applying things and I was traveling for a
> bit. Is this a bug that's urgent and needs to be fixed to keep
> these boards working in the v4.9-rc series? Does it need to go
> back to stable? The change is fairly large, so we might be able
> to put it into clk-fixes for -rc2, but it would need some
> justification and preferably a stable/fixes tag.
>
> Also, what about the other two patches in this series?
Yesterday I resent this series based on linux-next, so if you could
apply them to clk-next that would be great.
Thanks
^ permalink raw reply
* [PATCH 3/3] clk: imx6: Fix procedure to switch the parent of LDB_DI_CLK
From: Stephen Boyd @ 2016-10-19 0:05 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAOMZO5Ae_cB3BiqckAiOyaJPd2HWELkR8hVjEKHbY1nVOAeMxQ@mail.gmail.com>
On 10/18, Fabio Estevam wrote:
> Hi Stephen,
>
> On Tue, Oct 18, 2016 at 10:01 PM, Stephen Boyd <sboyd@codeaurora.org> wrote:
>
> > Urgh, sorry I missed this one and then we got too close to the
> > merge window to keep applying things and I was traveling for a
> > bit. Is this a bug that's urgent and needs to be fixed to keep
> > these boards working in the v4.9-rc series? Does it need to go
> > back to stable? The change is fairly large, so we might be able
> > to put it into clk-fixes for -rc2, but it would need some
> > justification and preferably a stable/fixes tag.
> >
> > Also, what about the other two patches in this series?
>
> Yesterday I resent this series based on linux-next, so if you could
> apply them to clk-next that would be great.
>
Ok that makes it easy. Thanks.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH/RESEND] recordmcount: arm: Implement make_nop
From: Steven Rostedt @ 2016-10-19 0:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161018234200.5804-1-sboyd@codeaurora.org>
On Tue, 18 Oct 2016 16:42:00 -0700
Stephen Boyd <sboyd@codeaurora.org> wrote:
> In similar spirit to x86 and arm64 support, add a make_nop_arm()
> to replace calls to mcount with a nop in sections that aren't
> traced.
>
> Cc: Russell King <linux@arm.linux.org.uk>
> Acked-by: Rabin Vincent <rabin@rab.in>
> Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
I can take this if I can get an ack from the ARM maintainers.
-- Steve
^ permalink raw reply
* [PATCH 1/2] ARM: dts: add EBI2 to the Qualcomm MSM8660 DTSI
From: Stephen Boyd @ 2016-10-19 0:51 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476775534-4493-1-git-send-email-linus.walleij@linaro.org>
On 10/18, Linus Walleij wrote:
> This adds the external bus interface EBI2 to the MSM8660 device
> tree, albeit with status = "disabled" so that devices actually
> using EBI2 can turn it on if needed.
>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ChangeLog v3->v4:
> - Rebase on kernel v4.9-rc1
> - Bindings and driver are merged so should be clear to apply.
> ChangeLog v2->v3:
> - Use the new #address-cells = <2> for indicating the CS in the
> first address cell
> - Use the ranges property properly for defining the six different
> CS address windows
> - Define CS3 to properly map over 128MB
> - The EBI2 bindings are now ACKed by Rob Herring and a pull request
> to ARM SoC for both binding and driver is pending.
> - This should be safe to merge for v4.9
> ---
> arch/arm/boot/dts/qcom-msm8660.dtsi | 17 +++++++++++++++++
> 1 file changed, 17 insertions(+)
>
> diff --git a/arch/arm/boot/dts/qcom-msm8660.dtsi b/arch/arm/boot/dts/qcom-msm8660.dtsi
> index 8c65e0d82559..0b6348544598 100644
> --- a/arch/arm/boot/dts/qcom-msm8660.dtsi
> +++ b/arch/arm/boot/dts/qcom-msm8660.dtsi
> @@ -141,6 +141,23 @@
> };
> };
>
> + ebi2 at 1a100000 {
Perhaps the node name should be more generic, like
external-bus at 1a100000
? I know, bikeshedding...
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH 2/2] ARM: dts: add SMSC ethernet on the APQ8060 Dragonboard
From: Stephen Boyd @ 2016-10-19 0:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476775542-4540-1-git-send-email-linus.walleij@linaro.org>
On 10/18, Linus Walleij wrote:
> @@ -167,6 +190,41 @@
> bias-pull-up;
> };
> };
> +
> + dragon_ebi2_pins: ebi2 {
> + /*
> + * Pins used by EBI2 on the Dragonboard, actually only
> + * only CS2 is used by a real peripheral. CS0 is just
> + * routed to a test point.
> + */
> + mux0 {
> + /*
> + * Pins used by EBI2 on the Dragonboard, actually only
> + * only CS2 is used by a real peripheral. CS0 is just
> + * routed to a test point.
> + */
Same comment twice? Plus it says "only only CS2", so we probably
want to drop one "only".
> + pins =
> + /* "gpio39", CS1A_N this is not good to mux */
> + "gpio40", /* CS2A_N */
> + "gpio134"; /* CS0_N testpoint TP29 */
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH v9 2/2] ARM: dts: add TOPEET itop elite based board
From: Ayaka @ 2016-10-19 1:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161018173748.GB30003@kozik-lap>
??? iPad ??
> Krzysztof Kozlowski <krzk@kernel.org> ? 2016?10?19? ??1:37 ???
>
>> On Wed, Oct 19, 2016 at 01:18:49AM +0800, Randy Li wrote:
>> The TOPEET itop exynos 4412 have three versions base board. The
>> Elite version is the cheap one without too much peripheral devices
>> on it.
>>
>> Currently supported are serial console, wired networking(USB),
>> USB OTG in peripheral mode, USB host, SD storage, GPIO buttons,
>> PWM beeper, ADC and LEDs. The WM8960 analog audio codec is also
>> enabled.
>>
>> The FIMC is not used for camera currently, I enabled it just for a
>> colorspace converter.
>>
>> Signed-off-by: Randy Li <ayaka@soulik.info>
>> Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
>
> Thanks, applied, with missing Rob's ack, minor changes in commit msg and
> fix in pin function (you used macro for pull up/down instead of
> function).
The last time I saw the other dts have applied that, but they are not now. A header file is also missed reported by kbuild, but I didn't meet that.
>
> Best regards,
> Krzysztof
^ permalink raw reply
* [PATCH v5 11/23] usb: chipidea: Emulate OTGSC interrupt enable path
From: Peter Chen @ 2016-10-19 1:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161018015636.11701-12-stephen.boyd@linaro.org>
On Mon, Oct 17, 2016 at 06:56:24PM -0700, Stephen Boyd wrote:
> In the case of an extcon-usb-gpio device being used with the
> chipidea driver we'll sometimes miss the BSVIS event in the OTGSC
> register. Consider the case where we don't have a cable attached
> and the id pin is indicating "host" mode. When we plug in the usb
> cable for "device" mode a gpio goes high and indicates that we
> should do the role switch and that vbus is high. When we're in
> "host" mode the OTGSC register doesn't have BSVIE set.
I have some questions for your description:
- Do you have any pending or related patches what this patch set
is based on? Afaik, the extcon-usb-gpio has no vbus event supported.
- When the ID from 0->1, the chipidea driver will do role switch, and
set BSVIE, why it does not occur for your case?
Peter
>
> The following scenario can happen:
>
> CPU0
> ----
> <extcon notifier chain>
> ci_cable_notifier()
> update id cable state
> ci_irq()
> if (ci->is_otg && (otgsc & OTGSC_IDIE) && (otgsc & OTGSC_IDIS)) { // true
> ci->id_event = true;
> ci_otg_queue_work()
> schedule()
>
> <extcon notifier event> // same task as before
> ci_cable_notifier()
> update vbus cable state
> ci_irq()
> if (ci->is_otg && (otgsc & OTGSC_BSVIE) && (otgsc & OTGSC_BSVIS)) // false
> return IRQ_NONE
>
> ci_otg_work() // switch task to the workqueue now
> if (ci->id_event)
> ci_handle_id_switch()
> ci_role_stop()
> host_stop()
> hw_wait_vbus_lower_bsv(ci); // this times out because vbus is already set
> ci_role_start()
> udc_id_switch_for_device()
> hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE, OTGSC_BSVIS | OTGSC_BSVIE);
>
> At this point, we don't replay the vbus connect event because the
> vbus event has already happened. This causes things like gadget
> instances to never see vbus appear, and thus the gadget is never
> started. Furthermore, we see timeout messages like:
>
> timeout waiting for 0000800 in OTGSC
>
> Let's workaround this by skiping the wait for BSV when we're
> using an extcon for the vbus notification and let's properly
> emulate the BSVIS event that would happen when we enable the
> vbus interrupt while enabling "device" mode.
>
> Cc: Peter Chen <peter.chen@nxp.com>
> Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
> Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
> ---
> drivers/usb/chipidea/ci.h | 2 ++
> drivers/usb/chipidea/core.c | 23 +++++++++++++++++------
> drivers/usb/chipidea/otg.c | 31 ++++++++++++++++++++++++-------
> 3 files changed, 43 insertions(+), 13 deletions(-)
>
> diff --git a/drivers/usb/chipidea/ci.h b/drivers/usb/chipidea/ci.h
> index 59e22389c10b..e099b8bc79e2 100644
> --- a/drivers/usb/chipidea/ci.h
> +++ b/drivers/usb/chipidea/ci.h
> @@ -437,6 +437,8 @@ static inline void ci_ulpi_exit(struct ci_hdrc *ci) { }
> static inline int ci_ulpi_resume(struct ci_hdrc *ci) { return 0; }
> #endif
>
> +irqreturn_t __ci_irq(int irq, struct ci_hdrc *ci);
> +
> u32 hw_read_intr_enable(struct ci_hdrc *ci);
>
> u32 hw_read_intr_status(struct ci_hdrc *ci);
> diff --git a/drivers/usb/chipidea/core.c b/drivers/usb/chipidea/core.c
> index 83bc2f2dd6a8..d1ae9a03e0fa 100644
> --- a/drivers/usb/chipidea/core.c
> +++ b/drivers/usb/chipidea/core.c
> @@ -524,9 +524,8 @@ int hw_device_reset(struct ci_hdrc *ci)
> return 0;
> }
>
> -static irqreturn_t ci_irq(int irq, void *data)
> +irqreturn_t __ci_irq(int irq, struct ci_hdrc *ci)
> {
> - struct ci_hdrc *ci = data;
> irqreturn_t ret = IRQ_NONE;
> u32 otgsc = 0;
>
> @@ -570,9 +569,20 @@ static irqreturn_t ci_irq(int irq, void *data)
> return IRQ_HANDLED;
> }
>
> - /* Handle device/host interrupt */
> - if (ci->role != CI_ROLE_END)
> - ret = ci_role(ci)->irq(ci);
> + return ret;
> +}
> +
> +static irqreturn_t ci_irq(int irq, void *data)
> +{
> + irqreturn_t ret;
> + struct ci_hdrc *ci = data;
> +
> + ret = __ci_irq(irq, ci);
> + if (ret == IRQ_NONE) {
> + /* Handle device/host interrupt */
> + if (ci->role != CI_ROLE_END)
> + ret = ci_role(ci)->irq(ci);
> + }
>
> return ret;
> }
> @@ -586,7 +596,8 @@ static int ci_cable_notifier(struct notifier_block *nb, unsigned long event,
> cbl->connected = event;
> cbl->changed = true;
>
> - ci_irq(ci->irq, ci);
> + __ci_irq(ci->irq, ci);
> +
> return NOTIFY_DONE;
> }
>
> diff --git a/drivers/usb/chipidea/otg.c b/drivers/usb/chipidea/otg.c
> index 695f3fe3ae21..f4a21ade1901 100644
> --- a/drivers/usb/chipidea/otg.c
> +++ b/drivers/usb/chipidea/otg.c
> @@ -84,36 +84,44 @@ u32 hw_read_otgsc(struct ci_hdrc *ci, u32 mask)
> void hw_write_otgsc(struct ci_hdrc *ci, u32 mask, u32 data)
> {
> struct ci_hdrc_cable *cable;
> + bool raise_irq = false;
>
> cable = &ci->platdata->vbus_extcon;
> if (!IS_ERR(cable->edev)) {
> - if (data & mask & OTGSC_BSVIS)
> - cable->changed = false;
> -
> /* Don't enable vbus interrupt if using external notifier */
> if (data & mask & OTGSC_BSVIE) {
> + if (cable->enabled == false && cable->changed == true)
> + raise_irq = true;
> cable->enabled = true;
> data &= ~OTGSC_BSVIE;
> } else if (mask & OTGSC_BSVIE) {
> cable->enabled = false;
> }
> +
> + if (data & mask & OTGSC_BSVIS && !raise_irq)
> + cable->changed = false;
> }
>
> cable = &ci->platdata->id_extcon;
> if (!IS_ERR(cable->edev)) {
> - if (data & mask & OTGSC_IDIS)
> - cable->changed = false;
> -
> /* Don't enable id interrupt if using external notifier */
> if (data & mask & OTGSC_IDIE) {
> + if (cable->enabled == false && cable->changed == true)
> + raise_irq = true;
> cable->enabled = true;
> data &= ~OTGSC_IDIE;
> } else if (mask & OTGSC_IDIE) {
> cable->enabled = false;
> }
> +
> + if (data & mask & OTGSC_IDIS && !raise_irq)
> + cable->changed = false;
> }
>
> hw_write(ci, OP_OTGSC, mask | OTGSC_INT_STATUS_BITS, data);
> +
> + if (raise_irq)
> + __ci_irq(ci->irq, ci);
> }
>
> /**
> @@ -175,7 +183,16 @@ static void ci_handle_id_switch(struct ci_hdrc *ci)
>
> ci_role_stop(ci);
>
> - if (role == CI_ROLE_GADGET)
> + /*
> + * BSV could be set "immediately" if we're using extcon for
> + * VBUS because sometimes it's a single GPIO for ID and VBUS
> + * like in the case of extcon-usb-gpio. In that case we ignore
> + * waiting for a BSV transition. Really we can't tell when BSV
> + * is low and the cable is connected, all we know is that the
> + * BSV is high when we update BSV state.
> + */
> + if (role == CI_ROLE_GADGET &&
> + IS_ERR(ci->platdata->vbus_extcon.edev))
> /*
> * wait vbus lower than OTGSC_BSV before connecting
> * to host
> --
> 2.10.0.297.gf6727b0
>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
--
Best Regards,
Peter Chen
^ permalink raw reply
* [PATCH] clocksource: arm_arch_timer: Don't assume clock runs in suspend
From: Stephen Boyd @ 2016-10-19 1:24 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161004174903.GA3098@localhost>
On 10/04, Brian Norris wrote:
> Hi Marc,
>
> On Thu, Sep 29, 2016 at 05:08:47PM +0100, Marc Zyngier wrote:
> > On Tue, 27 Sep 2016 18:23:11 -0700
> > Brian Norris <briannorris@chromium.org> wrote:
> > > On Tue, Sep 20, 2016 at 08:47:07AM +0100, Marc Zyngier wrote:
> > > <Begin side note>
> > > rk3288 (ARMv7 system widely used for our Chromebooks) has the same
> > > issue, except the kernel we're using for production (based on v3.14)
> > > doesn't have the following commit, which stopped utilizing the RTC:
> > >
> > > commit 0fa88cb4b82b5cf7429bc1cef9db006ca035754e
> > > Author: Xunlei Pang <pang.xunlei@linaro.org>
> > > Date: Wed Apr 1 20:34:38 2015 -0700
> > >
> > > time, drivers/rtc: Don't bother with rtc_resume() for the nonstop clocksource
> > >
> > > And any mainline testing on rk3288 doesn't see the problem, because
> > > mainline doesn't support its lowest-power sleep modes well enough (see
> > > ROCKCHIP_ARM_OFF_LOGIC_DEEP in arch/arm/mach-rockchip/pm.c).
> >
> > Arghh... So even my favourite Chromebook (from which I'm typing this
> > email) is affected? Not very nice...
>
> Yep. But if you're running mainline, you just get to have high S3 power
> consumption instead!
Just curious, do we enter this state during cpuidle as well? Or
is it only across suspend that the clock stops working?
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH] clocksource: arm_arch_timer: Don't assume clock runs in suspend
From: Brian Norris @ 2016-10-19 1:36 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161019012441.GW8871@codeaurora.org>
On Tue, Oct 18, 2016 at 06:24:41PM -0700, Stephen Boyd wrote:
> Just curious, do we enter this state during cpuidle as well? Or
> is it only across suspend that the clock stops working?
I believe we do not on either rk3288 or rk3399. We'd have to be powering
off almost the entire system before we'd be able to gate the 24 MHz
oscillator, AIUI.
Brian
^ permalink raw reply
* [PATCH v5 11/23] usb: chipidea: Emulate OTGSC interrupt enable path
From: Stephen Boyd @ 2016-10-19 1:53 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161019011535.GC6294@b29397-desktop>
Quoting Peter Chen (2016-10-18 18:15:35)
> On Mon, Oct 17, 2016 at 06:56:24PM -0700, Stephen Boyd wrote:
> > In the case of an extcon-usb-gpio device being used with the
> > chipidea driver we'll sometimes miss the BSVIS event in the OTGSC
> > register. Consider the case where we don't have a cable attached
> > and the id pin is indicating "host" mode. When we plug in the usb
> > cable for "device" mode a gpio goes high and indicates that we
> > should do the role switch and that vbus is high. When we're in
> > "host" mode the OTGSC register doesn't have BSVIE set.
>
> I have some questions for your description:
>
> - Do you have any pending or related patches what this patch set
> is based on? Afaik, the extcon-usb-gpio has no vbus event supported.
If you're asking if I've made modifications to extcon-usb-gpio, then the
answer is no. The branch on linaro.org git server from the cover-letter
is the branch I've used to test this with. This patch is specifically to
fix issues with that design on the db410c board that has only one pin
for ID and vbus detection. It's the schematic that we've discussed in
another thread.
extcon-usb-gpio sends two extcon events, EXTCON_USB_HOST (for the id
pin) and EXTCON_USB (for the vbus). So afaik it does support vbus
events.
> - When the ID from 0->1, the chipidea driver will do role switch, and
> set BSVIE, why it does not occur for your case?
Right, that happens with this line in the sequence I describe below:
hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE, OTGSC_BSVIS | OTGSC_BSVIE);
but that happens much later than when the extcon event happens so we
miss the interrupt. Technically, the driver isn't expecting the BSVIS
interrupt to happen until BSVIE is set, but the extcon can come whenever
it wants regardless of how the registers are configured in the
controller. So we have to do some sort of 'caching' here to remember
that the vbus event happened and replay it when BSVIE is set. At least I
imagine this is how the hardware would work? Or if vbus goes high before
we enable the interrupt would it just be missed? It seems like polling
the BSV bit and then enabling BSVIE is sort of racy there.
Plus, we poll the BSV bit when we role switch, but in my case id bit
toggles and vbus goes high at exactly the same time because that is all
happening from a single cable being connected, so it's not possible for
BSV to go low and see it after the id pin from 0 to 1.
>
> Peter
> >
> > The following scenario can happen:
> >
> > CPU0
> > ----
> > <extcon notifier chain>
> > ci_cable_notifier()
> > update id cable state
> > ci_irq()
> > if (ci->is_otg && (otgsc & OTGSC_IDIE) && (otgsc & OTGSC_IDIS)) { // true
> > ci->id_event = true;
> > ci_otg_queue_work()
> > schedule()
> >
> > <extcon notifier event> // same task as before
> > ci_cable_notifier()
> > update vbus cable state
> > ci_irq()
> > if (ci->is_otg && (otgsc & OTGSC_BSVIE) && (otgsc & OTGSC_BSVIS)) // false
> > return IRQ_NONE
> >
> > ci_otg_work() // switch task to the workqueue now
> > if (ci->id_event)
> > ci_handle_id_switch()
> > ci_role_stop()
> > host_stop()
> > hw_wait_vbus_lower_bsv(ci); // this times out because vbus is already set
> > ci_role_start()
> > udc_id_switch_for_device()
> > hw_write_otgsc(ci, OTGSC_BSVIS | OTGSC_BSVIE, OTGSC_BSVIS | OTGSC_BSVIE);
> >
> > At this point, we don't replay the vbus connect event because the
> > vbus event has already happened. This causes things like gadget
> > instances to never see vbus appear, and thus the gadget is never
> > started. Furthermore, we see timeout messages like:
> >
> > timeout waiting for 0000800 in OTGSC
> >
> > Let's workaround this by skiping the wait for BSV when we're
> > using an extcon for the vbus notification and let's properly
> > emulate the BSVIS event that would happen when we enable the
> > vbus interrupt while enabling "device" mode.
^ permalink raw reply
* [PATCH] clocksource: arm_arch_timer: Don't assume clock runs in suspend
From: Stephen Boyd @ 2016-10-19 1:55 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161019013612.GA107490@google.com>
On 10/18/2016 06:36 PM, Brian Norris wrote:
> I believe we do not on either rk3288 or rk3399. We'd have to be powering
> off almost the entire system before we'd be able to gate the 24 MHz
> oscillator, AIUI.
>
Great! That avoids a major headache.
--
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply
* [PATCH v7, 0/8] Add MediaTek USB3 DRD Driver
From: Chunfeng Yun @ 2016-10-19 2:28 UTC (permalink / raw)
To: linux-arm-kernel
These patches introduce the MediaTek USB3 dual-role controller
driver.
The driver can be configured as Dual-Role Device (DRD),
Peripheral Only and Host Only (xHCI) modes. It works well
with Mass Storage, RNDIS and g_zero on FS/HS and SS. And it is
tested on MT8173 platform which only contains USB2.0 device IP,
and on MT6290 platform which contains USB3.0 device IP.
Change in v7:
1. split dual-role driver into four patchs
2. remove QMU done tasklet
3. add a bool in xhci_hcd_mtk to signal absence of IPPC
Change in v6:
1. handle endianness of GPD and SETUP data
2. remove dummy error log and return suitable error number
3. cancel delay work when deregiseter driver
Change in v5:
1. modify some comments
2. rename some unsuitable variables
3. add reg-names property for host node
4. add USB_MTU3_DEBUG to control debug messages
Change in v4:
1. fix build errors on non-mediatek platforms
2. provide manual dual-role switch via debugfs instead of sysfs
Change in v3:
1. fix some typo error
2. rename mtu3.txt to mt8173-mtu3.txt
Change in v2:
1. modify binding docs according to suggestions
2. modify some comments and remove some dummy blank lines
3. fix memory leakage
Chunfeng Yun (8):
dt-bindings: mt8173-xhci: support host side of dual-role mode
dt-bindings: mt8173-mtu3: add devicetree bindings
usb: xhci-mtk: make IPPC register optional
usb: Add MediaTek USB3 DRD driver
usb: mtu3: Super-Speed Peripheral mode support
usb: mtu3: host only mode support
usb: mtu3: dual-role mode support
arm64: dts: mediatek: add USB3 DRD driver
.../devicetree/bindings/usb/mt8173-mtu3.txt | 87 ++
.../devicetree/bindings/usb/mt8173-xhci.txt | 54 +-
arch/arm64/boot/dts/mediatek/mt8173-evb.dts | 63 +-
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 29 +-
drivers/usb/Kconfig | 2 +
drivers/usb/Makefile | 1 +
drivers/usb/host/xhci-mtk.c | 38 +-
drivers/usb/host/xhci-mtk.h | 1 +
drivers/usb/mtu3/Kconfig | 54 ++
drivers/usb/mtu3/Makefile | 18 +
drivers/usb/mtu3/mtu3.h | 417 +++++++++
drivers/usb/mtu3/mtu3_core.c | 859 +++++++++++++++++++
drivers/usb/mtu3/mtu3_dr.c | 379 +++++++++
drivers/usb/mtu3/mtu3_dr.h | 108 +++
drivers/usb/mtu3/mtu3_gadget.c | 730 ++++++++++++++++
drivers/usb/mtu3/mtu3_gadget_ep0.c | 881 ++++++++++++++++++++
drivers/usb/mtu3/mtu3_host.c | 294 +++++++
drivers/usb/mtu3/mtu3_hw_regs.h | 473 +++++++++++
drivers/usb/mtu3/mtu3_plat.c | 484 +++++++++++
drivers/usb/mtu3/mtu3_qmu.c | 573 +++++++++++++
drivers/usb/mtu3/mtu3_qmu.h | 43 +
21 files changed, 5561 insertions(+), 27 deletions(-)
create mode 100644 Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
create mode 100644 drivers/usb/mtu3/Kconfig
create mode 100644 drivers/usb/mtu3/Makefile
create mode 100644 drivers/usb/mtu3/mtu3.h
create mode 100644 drivers/usb/mtu3/mtu3_core.c
create mode 100644 drivers/usb/mtu3/mtu3_dr.c
create mode 100644 drivers/usb/mtu3/mtu3_dr.h
create mode 100644 drivers/usb/mtu3/mtu3_gadget.c
create mode 100644 drivers/usb/mtu3/mtu3_gadget_ep0.c
create mode 100644 drivers/usb/mtu3/mtu3_host.c
create mode 100644 drivers/usb/mtu3/mtu3_hw_regs.h
create mode 100644 drivers/usb/mtu3/mtu3_plat.c
create mode 100644 drivers/usb/mtu3/mtu3_qmu.c
create mode 100644 drivers/usb/mtu3/mtu3_qmu.h
--
1.7.9.5
^ permalink raw reply
* [PATCH v7, 1/8] dt-bindings: mt8173-xhci: support host side of dual-role mode
From: Chunfeng Yun @ 2016-10-19 2:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476844107-31087-1-git-send-email-chunfeng.yun@mediatek.com>
Some resources, such as IPPC register etc, shared with device
driver are moved into common glue layer when xHCI driver is the
host side of dual-role mode and they should be changed as optional
properties if they are required ones before. For clarity, add
a new part of binding to support host side of dual-role mode.
Additionally add optional properties of pinctrl for host only mode
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/usb/mt8173-xhci.txt | 54 +++++++++++++++++++-
1 file changed, 52 insertions(+), 2 deletions(-)
diff --git a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
index b3a7ffa..2a930bd 100644
--- a/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
+++ b/Documentation/devicetree/bindings/usb/mt8173-xhci.txt
@@ -2,10 +2,18 @@ MT8173 xHCI
The device node for Mediatek SOC USB3.0 host controller
+There are two scenarios: the first one only supports xHCI driver;
+the second one supports dual-role mode, and the host is based on xHCI
+driver. Take account of backward compatibility, we divide bindings
+into two parts.
+
+1st: only supports xHCI driver
+------------------------------------------------------------------------
+
Required properties:
- compatible : should contain "mediatek,mt8173-xhci"
- - reg : specifies physical base address and size of the registers,
- the first one for MAC, the second for IPPC
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be "mac" for xHCI MAC and "ippc" for IP port control
- interrupts : interrupt used by the controller
- power-domains : a phandle to USB power domain node to control USB's
mtcmos
@@ -27,12 +35,16 @@ Optional properties:
control register, it depends on "mediatek,wakeup-src".
- vbus-supply : reference to the VBUS regulator;
- usb3-lpm-capable : supports USB3.0 LPM
+ - pinctrl-names : a pinctrl state named "default" must be defined
+ - pinctrl-0 : pin control group
+ See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
Example:
usb30: usb at 11270000 {
compatible = "mediatek,mt8173-xhci";
reg = <0 0x11270000 0 0x1000>,
<0 0x11280700 0 0x0100>;
+ reg-names = "mac", "ippc";
interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
clocks = <&topckgen CLK_TOP_USB30_SEL>,
@@ -49,3 +61,41 @@ usb30: usb at 11270000 {
mediatek,syscon-wakeup = <&pericfg>;
mediatek,wakeup-src = <1>;
};
+
+2nd: dual-role mode with xHCI driver
+------------------------------------------------------------------------
+
+In the case, xhci is added as subnode to mtu3. An example and the DT binding
+details of mtu3 can be found in:
+Documentation/devicetree/bindings/usb/mtu3.txt
+
+Required properties:
+ - compatible : should contain "mediatek,mt8173-xhci"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be "mac" for xHCI MAC
+ - interrupts : interrupt used by the host controller
+ - power-domains : a phandle to USB power domain node to control USB's
+ mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+ - clock-names : must be
+ "sys_ck": for clock of xHCI MAC
+
+Optional properties:
+ - vbus-supply : reference to the VBUS regulator;
+ - usb3-lpm-capable : supports USB3.0 LPM
+
+Example:
+usb30: usb at 11270000 {
+ compatible = "mediatek,mt8173-xhci";
+ reg = <0 0x11270000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>;
+ clock-names = "sys_ck";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ usb3-lpm-capable;
+};
--
1.7.9.5
^ permalink raw reply related
* [PATCH v7, 2/8] dt-bindings: mt8173-mtu3: add devicetree bindings
From: Chunfeng Yun @ 2016-10-19 2:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476844107-31087-1-git-send-email-chunfeng.yun@mediatek.com>
add a DT binding doc for MediaTek USB3 DRD driver
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/usb/mt8173-mtu3.txt | 87 ++++++++++++++++++++
1 file changed, 87 insertions(+)
create mode 100644 Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
diff --git a/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
new file mode 100644
index 0000000..e049d19
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mt8173-mtu3.txt
@@ -0,0 +1,87 @@
+The device node for Mediatek USB3.0 DRD controller
+
+Required properties:
+ - compatible : should be "mediatek,mt8173-mtu3"
+ - reg : specifies physical base address and size of the registers
+ - reg-names: should be "mac" for device IP and "ippc" for IP port control
+ - interrupts : interrupt used by the device IP
+ - power-domains : a phandle to USB power domain node to control USB's
+ mtcmos
+ - vusb33-supply : regulator of USB avdd3.3v
+ - clocks : a list of phandle + clock-specifier pairs, one for each
+ entry in clock-names
+ - clock-names : must contain "sys_ck" for clock of controller;
+ "wakeup_deb_p0" and "wakeup_deb_p1" are optional, they are
+ depends on "mediatek,enable-wakeup"
+ - phys : a list of phandle + phy specifier pairs
+ - dr_mode : should be one of "host", "peripheral" or "otg",
+ refer to usb/generic.txt
+
+Optional properties:
+ - #address-cells, #size-cells : should be '2' if the device has sub-nodes
+ with 'reg' property
+ - ranges : allows valid 1:1 translation between child's address space and
+ parent's address space
+ - extcon : external connector for vbus and idpin changes detection, needed
+ when supports dual-role mode.
+ - vbus-supply : reference to the VBUS regulator, needed when supports
+ dual-role mode.
+ - pinctl-names : a pinctrl state named "default" must be defined,
+ "id_float" and "id_ground" are optinal which depends on
+ "mediatek,enable-manual-drd"
+ - pinctrl-0 : pin control group
+ See: Documentation/devicetree/bindings/pinctrl/pinctrl-binding.txt
+
+ - maximum-speed : valid arguments are "super-speed", "high-speed" and
+ "full-speed"; refer to usb/generic.txt
+ - enable-manual-drd : supports manual dual-role switch via debugfs; usually
+ used when receptacle is TYPE-A and also wants to support dual-role
+ mode.
+ - mediatek,enable-wakeup : supports ip sleep wakeup used by host mode
+ - mediatek,syscon-wakeup : phandle to syscon used to access USB wakeup
+ control register, it depends on "mediatek,enable-wakeup".
+
+Sub-nodes:
+The xhci should be added as subnode to mtu3 as shown in the following example
+if host mode is enabled. The DT binding details of xhci can be found in:
+Documentation/devicetree/bindings/usb/mt8173-xhci.txt
+
+Example:
+ssusb: usb at 11271000 {
+ compatible = "mediatek,mt8173-mtu3";
+ reg = <0 0x11271000 0 0x3000>,
+ <0 0x11280700 0 0x0100>;
+ reg-names = "mac", "ippc";
+ interrupts = <GIC_SPI 64 IRQ_TYPE_LEVEL_LOW>;
+ phys = <&phy_port0 PHY_TYPE_USB3>,
+ <&phy_port1 PHY_TYPE_USB2>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>,
+ <&pericfg CLK_PERI_USB0>,
+ <&pericfg CLK_PERI_USB1>;
+ clock-names = "sys_ck",
+ "wakeup_deb_p0",
+ "wakeup_deb_p1";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ vbus-supply = <&usb_p0_vbus>;
+ extcon = <&extcon_usb>;
+ dr_mode = "otg";
+ mediatek,enable-wakeup;
+ mediatek,syscon-wakeup = <&pericfg>;
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+ status = "disabled";
+
+ usb_host: xhci at 11270000 {
+ compatible = "mediatek,mt8173-xhci";
+ reg = <0 0x11270000 0 0x1000>;
+ reg-names = "mac";
+ interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
+ power-domains = <&scpsys MT8173_POWER_DOMAIN_USB>;
+ clocks = <&topckgen CLK_TOP_USB30_SEL>;
+ clock-names = "sys_ck";
+ vusb33-supply = <&mt6397_vusb_reg>;
+ status = "disabled";
+ };
+};
--
1.7.9.5
^ permalink raw reply related
* [PATCH v7, 3/8] usb: xhci-mtk: make IPPC register optional
From: Chunfeng Yun @ 2016-10-19 2:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476844107-31087-1-git-send-email-chunfeng.yun@mediatek.com>
Make IPPC register optional to support host side of dual-role mode,
due to it is moved into common glue layer for simplification.
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/usb/host/xhci-mtk.c | 38 +++++++++++++++++++++++++++++++-------
drivers/usb/host/xhci-mtk.h | 1 +
2 files changed, 32 insertions(+), 7 deletions(-)
diff --git a/drivers/usb/host/xhci-mtk.c b/drivers/usb/host/xhci-mtk.c
index 79959f1..1094ebd 100644
--- a/drivers/usb/host/xhci-mtk.c
+++ b/drivers/usb/host/xhci-mtk.c
@@ -94,6 +94,9 @@ static int xhci_mtk_host_enable(struct xhci_hcd_mtk *mtk)
int ret;
int i;
+ if (!mtk->has_ippc)
+ return 0;
+
/* power on host ip */
value = readl(&ippc->ip_pw_ctr1);
value &= ~CTRL1_IP_HOST_PDN;
@@ -139,6 +142,9 @@ static int xhci_mtk_host_disable(struct xhci_hcd_mtk *mtk)
int ret;
int i;
+ if (!mtk->has_ippc)
+ return 0;
+
/* power down all u3 ports */
for (i = 0; i < mtk->num_u3_ports; i++) {
value = readl(&ippc->u3_ctrl_p[i]);
@@ -173,6 +179,9 @@ static int xhci_mtk_ssusb_config(struct xhci_hcd_mtk *mtk)
struct mu3c_ippc_regs __iomem *ippc = mtk->ippc_regs;
u32 value;
+ if (!mtk->has_ippc)
+ return 0;
+
/* reset whole ip */
value = readl(&ippc->ip_pw_ctr0);
value |= CTRL0_IP_SW_RST;
@@ -475,6 +484,7 @@ static void xhci_mtk_quirks(struct device *dev, struct xhci_hcd *xhci)
/* called during probe() after chip reset completes */
static int xhci_mtk_setup(struct usb_hcd *hcd)
{
+ struct xhci_hcd *xhci = hcd_to_xhci(hcd);
struct xhci_hcd_mtk *mtk = hcd_to_mtk(hcd);
int ret;
@@ -482,12 +492,21 @@ static int xhci_mtk_setup(struct usb_hcd *hcd)
ret = xhci_mtk_ssusb_config(mtk);
if (ret)
return ret;
+ }
+
+ ret = xhci_gen_setup(hcd, xhci_mtk_quirks);
+ if (ret)
+ return ret;
+
+ if (usb_hcd_is_primary_hcd(hcd)) {
+ mtk->num_u3_ports = xhci->num_usb3_ports;
+ mtk->num_u2_ports = xhci->num_usb2_ports;
ret = xhci_mtk_sch_init(mtk);
if (ret)
return ret;
}
- return xhci_gen_setup(hcd, xhci_mtk_quirks);
+ return ret;
}
static int xhci_mtk_probe(struct platform_device *pdev)
@@ -586,7 +605,7 @@ static int xhci_mtk_probe(struct platform_device *pdev)
mtk->hcd = platform_get_drvdata(pdev);
platform_set_drvdata(pdev, mtk);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "mac");
hcd->regs = devm_ioremap_resource(dev, res);
if (IS_ERR(hcd->regs)) {
ret = PTR_ERR(hcd->regs);
@@ -595,11 +614,16 @@ static int xhci_mtk_probe(struct platform_device *pdev)
hcd->rsrc_start = res->start;
hcd->rsrc_len = resource_size(res);
- res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
- mtk->ippc_regs = devm_ioremap_resource(dev, res);
- if (IS_ERR(mtk->ippc_regs)) {
- ret = PTR_ERR(mtk->ippc_regs);
- goto put_usb2_hcd;
+ res = platform_get_resource_byname(pdev, IORESOURCE_MEM, "ippc");
+ if (res) { /* ippc register is optional */
+ mtk->ippc_regs = devm_ioremap_resource(dev, res);
+ if (IS_ERR(mtk->ippc_regs)) {
+ ret = PTR_ERR(mtk->ippc_regs);
+ goto put_usb2_hcd;
+ }
+ mtk->has_ippc = true;
+ } else {
+ mtk->has_ippc = false;
}
for (phy_num = 0; phy_num < mtk->num_phys; phy_num++) {
diff --git a/drivers/usb/host/xhci-mtk.h b/drivers/usb/host/xhci-mtk.h
index 7da677c..2845c49 100644
--- a/drivers/usb/host/xhci-mtk.h
+++ b/drivers/usb/host/xhci-mtk.h
@@ -118,6 +118,7 @@ struct xhci_hcd_mtk {
struct usb_hcd *hcd;
struct mu3h_sch_bw_info *sch_array;
struct mu3c_ippc_regs __iomem *ippc_regs;
+ bool has_ippc;
int num_u2_ports;
int num_u3_ports;
struct regulator *vusb33;
--
1.7.9.5
^ permalink raw reply related
* [PATCH v7, 5/8] usb: mtu3: Super-Speed Peripheral mode support
From: Chunfeng Yun @ 2016-10-19 2:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1476844107-31087-1-git-send-email-chunfeng.yun@mediatek.com>
add super-speed funtion for peripheral mode
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
---
drivers/usb/mtu3/mtu3.h | 13 ++-
drivers/usb/mtu3/mtu3_core.c | 202 ++++++++++++++++++++++++++++++++----
drivers/usb/mtu3/mtu3_gadget.c | 45 +++++---
drivers/usb/mtu3/mtu3_gadget_ep0.c | 90 ++++++++++++++++
drivers/usb/mtu3/mtu3_hw_regs.h | 33 ++++++
5 files changed, 346 insertions(+), 37 deletions(-)
diff --git a/drivers/usb/mtu3/mtu3.h b/drivers/usb/mtu3/mtu3.h
index ad1a133..41a0473 100644
--- a/drivers/usb/mtu3/mtu3.h
+++ b/drivers/usb/mtu3/mtu3.h
@@ -53,6 +53,7 @@
#define USB_QMU_TQSAR(epnum) (U3D_TXQSAR1 + (((epnum) - 1) * 0x10))
#define USB_QMU_TQCPR(epnum) (U3D_TXQCPR1 + (((epnum) - 1) * 0x10))
+#define SSUSB_U3_CTRL(p) (U3D_SSUSB_U3_CTRL_0P + ((p) * 0x08))
#define SSUSB_U2_CTRL(p) (U3D_SSUSB_U2_CTRL_0P + ((p) * 0x08))
#define MTU3_DRIVER_NAME "mtu3"
@@ -63,6 +64,7 @@
#define MTU3_EP_WEDGE BIT(2)
#define MTU3_EP_BUSY BIT(3)
+#define MTU3_U3_IP_SLOT_DEFAULT 2
#define MTU3_U2_IP_SLOT_DEFAULT 1
/**
@@ -87,6 +89,7 @@ enum mtu3_speed {
MTU3_SPEED_INACTIVE = 0,
MTU3_SPEED_FULL = 1,
MTU3_SPEED_HIGH = 3,
+ MTU3_SPEED_SUPER = 4,
};
/**
@@ -190,6 +193,7 @@ struct mtu3_ep {
struct list_head req_list;
struct mtu3_gpd_ring gpd_ring;
+ const struct usb_ss_ep_comp_descriptor *comp_desc;
const struct usb_endpoint_descriptor *desc;
int flags;
@@ -208,7 +212,8 @@ struct mtu3_request {
/**
* struct mtu3 - device driver instance data.
- * @slot: MTU3_U2_IP_SLOT_DEFAULT for U2 IP
+ * @slot: MTU3_U2_IP_SLOT_DEFAULT for U2 IP only,
+ * MTU3_U3_IP_SLOT_DEFAULT for U3 IP
* @may_wakeup: means device's remote wakeup is enabled
* @is_self_powered: is reported in device status and the config descriptor
* @ep0_req: dummy request used while handling standard USB requests
@@ -242,12 +247,16 @@ struct mtu3 {
struct usb_gadget_driver *gadget_driver;
struct mtu3_request ep0_req;
u8 setup_buf[EP0_RESPONSE_BUF];
+ u32 max_speed;
unsigned is_active:1;
unsigned may_wakeup:1;
unsigned is_self_powered:1;
unsigned test_mode:1;
unsigned softconnect:1;
+ unsigned u1_enable:1;
+ unsigned u2_enable:1;
+ unsigned is_u3_ip:1;
u8 address;
u8 test_mode_nr;
@@ -324,7 +333,7 @@ int mtu3_config_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
void mtu3_ep0_setup(struct mtu3 *mtu);
void mtu3_start(struct mtu3 *mtu);
void mtu3_stop(struct mtu3 *mtu);
-void mtu3_hs_softconn_set(struct mtu3 *mtu, bool enable);
+void mtu3_dev_on_off(struct mtu3 *mtu, int is_on);
int mtu3_gadget_setup(struct mtu3 *mtu);
void mtu3_gadget_cleanup(struct mtu3 *mtu);
diff --git a/drivers/usb/mtu3/mtu3_core.c b/drivers/usb/mtu3/mtu3_core.c
index 33d21dd..f9817ad 100644
--- a/drivers/usb/mtu3/mtu3_core.c
+++ b/drivers/usb/mtu3/mtu3_core.c
@@ -72,8 +72,20 @@ static void ep_fifo_free(struct mtu3_ep *mep)
__func__, mep->fifo_seg_size, mep->fifo_size, start_bit);
}
+/* enable/disable U3D SS function */
+static inline void mtu3_ss_func_set(struct mtu3 *mtu, bool enable)
+{
+ /* If usb3_en==0, LTSSM will go to SS.Disable state */
+ if (enable)
+ mtu3_setbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
+ else
+ mtu3_clrbits(mtu->mac_base, U3D_USB3_CONFIG, USB3_EN);
+
+ dev_dbg(mtu->dev, "USB3_EN = %d\n", !!enable);
+}
+
/* set/clear U3D HS device soft connect */
-void mtu3_hs_softconn_set(struct mtu3 *mtu, bool enable)
+static inline void mtu3_hs_softconn_set(struct mtu3 *mtu, bool enable)
{
if (enable) {
mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT,
@@ -92,6 +104,13 @@ static int mtu3_device_enable(struct mtu3 *mtu)
u32 check_clk = 0;
mtu3_clrbits(ibase, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
+
+ if (mtu->is_u3_ip) {
+ check_clk = SSUSB_U3_MAC_RST_B_STS;
+ mtu3_clrbits(ibase, SSUSB_U3_CTRL(0),
+ (SSUSB_U3_PORT_DIS | SSUSB_U3_PORT_PDN |
+ SSUSB_U3_PORT_HOST_SEL));
+ }
mtu3_clrbits(ibase, SSUSB_U2_CTRL(0),
(SSUSB_U2_PORT_DIS | SSUSB_U2_PORT_PDN |
SSUSB_U2_PORT_HOST_SEL));
@@ -104,6 +123,10 @@ static void mtu3_device_disable(struct mtu3 *mtu)
{
void __iomem *ibase = mtu->ippc_base;
+ if (mtu->is_u3_ip)
+ mtu3_setbits(ibase, SSUSB_U3_CTRL(0),
+ (SSUSB_U3_PORT_DIS | SSUSB_U3_PORT_PDN));
+
mtu3_setbits(ibase, SSUSB_U2_CTRL(0),
SSUSB_U2_PORT_DIS | SSUSB_U2_PORT_PDN);
mtu3_clrbits(ibase, SSUSB_U2_CTRL(0), SSUSB_U2_PORT_OTG_SEL);
@@ -142,6 +165,9 @@ static void mtu3_intr_status_clear(struct mtu3 *mtu)
/* Clear U2 USB common interrupts status */
mtu3_writel(mbase, U3D_COMMON_USB_INTR, ~0x0);
+ /* Clear U3 LTSSM interrupts status */
+ mtu3_writel(mbase, U3D_LTSSM_INTR, ~0x0);
+
/* Clear speed change interrupt status */
mtu3_writel(mbase, U3D_DEV_LINK_INTR, ~0x0);
}
@@ -153,13 +179,20 @@ static void mtu3_intr_enable(struct mtu3 *mtu)
u32 value;
/*Enable level 1 interrupts (BMU, QMU, MAC3, DMA, MAC2, EPCTL) */
- value = BMU_INTR | QMU_INTR | MAC2_INTR | EP_CTRL_INTR;
+ value = BMU_INTR | QMU_INTR | MAC3_INTR | MAC2_INTR | EP_CTRL_INTR;
mtu3_writel(mbase, U3D_LV1IESR, value);
/* Enable U2 common USB interrupts */
value = SUSPEND_INTR | RESUME_INTR | RESET_INTR;
mtu3_writel(mbase, U3D_COMMON_USB_INTR_ENABLE, value);
+ if (mtu->is_u3_ip) {
+ /* Enable U3 LTSSM interrupts */
+ value = HOT_RST_INTR | WARM_RST_INTR | VBUS_RISE_INTR |
+ VBUS_FALL_INTR | ENTER_U3_INTR | EXIT_U3_INTR;
+ mtu3_writel(mbase, U3D_LTSSM_INTR_ENABLE, value);
+ }
+
/* Enable QMU interrupts. */
value = TXQ_CSERR_INT | TXQ_LENERR_INT | RXQ_CSERR_INT |
RXQ_LENERR_INT | RXQ_ZLPERR_INT;
@@ -205,6 +238,17 @@ void mtu3_ep_stall_set(struct mtu3_ep *mep, bool set)
set ? "SEND STALL" : "CLEAR STALL, with EP RESET");
}
+void mtu3_dev_on_off(struct mtu3 *mtu, int is_on)
+{
+ if (mtu->is_u3_ip && (mtu->max_speed == USB_SPEED_SUPER))
+ mtu3_ss_func_set(mtu, is_on);
+ else
+ mtu3_hs_softconn_set(mtu, is_on);
+
+ dev_info(mtu->dev, "gadget (%s) pullup D%s\n",
+ usb_speed_string(mtu->max_speed), is_on ? "+" : "-");
+}
+
void mtu3_start(struct mtu3 *mtu)
{
void __iomem *mbase = mtu->mac_base;
@@ -214,13 +258,21 @@ void mtu3_start(struct mtu3 *mtu)
mtu3_clrbits(mtu->ippc_base, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
+ /*
+ * When disable U2 port, USB2_CSR's register will be reset to
+ * default value after re-enable it again(HS is enabled by default).
+ * So if force mac to work as FS, disable HS function.
+ */
+ if (mtu->max_speed == USB_SPEED_FULL)
+ mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+
/* Initialize the default interrupts */
mtu3_intr_enable(mtu);
mtu->is_active = 1;
if (mtu->softconnect)
- mtu3_hs_softconn_set(mtu, 1);
+ mtu3_dev_on_off(mtu, 1);
}
void mtu3_stop(struct mtu3 *mtu)
@@ -231,7 +283,7 @@ void mtu3_stop(struct mtu3 *mtu)
mtu3_intr_status_clear(mtu);
if (mtu->softconnect)
- mtu3_hs_softconn_set(mtu, 0);
+ mtu3_dev_on_off(mtu, 0);
mtu->is_active = 0;
mtu3_setbits(mtu->ippc_base, U3D_SSUSB_IP_PW_CTRL2, SSUSB_IP_DEV_PDN);
@@ -362,7 +414,10 @@ void mtu3_deconfig_ep(struct mtu3 *mtu, struct mtu3_ep *mep)
}
/*
- * 1. when supports only HS, the fifo is shared for all EPs, and
+ * Two scenarios:
+ * 1. when device IP supports SS, the fifo of EP0, TX EPs, RX EPs
+ * are separated;
+ * 2. when supports only HS, the fifo is shared for all EPs, and
* the capability registers of @EPNTXFFSZ or @EPNRXFFSZ indicate
* the total fifo size of non-ep0, and ep0's is fixed to 64B,
* so the total fifo size is 64B + @EPNTXFFSZ;
@@ -376,18 +431,33 @@ static void get_ep_fifo_config(struct mtu3 *mtu)
struct mtu3_fifo_info *rx_fifo;
u32 fifosize;
- fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
- tx_fifo = &mtu->tx_fifo;
- tx_fifo->base = MTU3_U2_IP_EP0_FIFO_SIZE;
- tx_fifo->limit = (fifosize / MTU3_EP_FIFO_UNIT) >> 1;
- bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
-
- rx_fifo = &mtu->rx_fifo;
- rx_fifo->base =
- tx_fifo->base + tx_fifo->limit * MTU3_EP_FIFO_UNIT;
- rx_fifo->limit = tx_fifo->limit;
- bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
- mtu->slot = MTU3_U2_IP_SLOT_DEFAULT;
+ if (mtu->is_u3_ip) {
+ fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
+ tx_fifo = &mtu->tx_fifo;
+ tx_fifo->base = 0;
+ tx_fifo->limit = fifosize / MTU3_EP_FIFO_UNIT;
+ bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+
+ fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNRXFFSZ);
+ rx_fifo = &mtu->rx_fifo;
+ rx_fifo->base = 0;
+ rx_fifo->limit = fifosize / MTU3_EP_FIFO_UNIT;
+ bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+ mtu->slot = MTU3_U3_IP_SLOT_DEFAULT;
+ } else {
+ fifosize = mtu3_readl(mtu->mac_base, U3D_CAP_EPNTXFFSZ);
+ tx_fifo = &mtu->tx_fifo;
+ tx_fifo->base = MTU3_U2_IP_EP0_FIFO_SIZE;
+ tx_fifo->limit = (fifosize / MTU3_EP_FIFO_UNIT) >> 1;
+ bitmap_zero(tx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+
+ rx_fifo = &mtu->rx_fifo;
+ rx_fifo->base =
+ tx_fifo->base + tx_fifo->limit * MTU3_EP_FIFO_UNIT;
+ rx_fifo->limit = tx_fifo->limit;
+ bitmap_zero(rx_fifo->bitmap, MTU3_FIFO_BIT_SIZE);
+ mtu->slot = MTU3_U2_IP_SLOT_DEFAULT;
+ }
dev_dbg(mtu->dev, "%s, TX: base-%d, limit-%d; RX: base-%d, limit-%d\n",
__func__, tx_fifo->base, tx_fifo->limit,
@@ -416,17 +486,21 @@ static int mtu3_mem_alloc(struct mtu3 *mtu)
void __iomem *mbase = mtu->mac_base;
struct mtu3_ep *ep_array;
int in_ep_num, out_ep_num;
- u32 cap_epinfo;
+ u32 cap_epinfo, cap_dev;
int ret;
int i;
mtu->hw_version = mtu3_readl(mtu->ippc_base, U3D_SSUSB_HW_ID);
+ cap_dev = mtu3_readl(mtu->ippc_base, U3D_SSUSB_IP_DEV_CAP);
+ mtu->is_u3_ip = !!SSUSB_IP_DEV_U3_PORT_NUM(cap_dev);
+
cap_epinfo = mtu3_readl(mbase, U3D_CAP_EPINFO);
in_ep_num = CAP_TX_EP_NUM(cap_epinfo);
out_ep_num = CAP_RX_EP_NUM(cap_epinfo);
- dev_info(mtu->dev, "IP version 0x%x\n", mtu->hw_version);
+ dev_info(mtu->dev, "IP version 0x%x(%s IP)\n", mtu->hw_version,
+ mtu->is_u3_ip ? "U3" : "U2");
dev_info(mtu->dev, "fifosz/epnum: Tx=%#x/%d, Rx=%#x/%d\n",
mtu3_readl(mbase, U3D_CAP_EPNTXFFSZ), in_ep_num,
mtu3_readl(mbase, U3D_CAP_EPNRXFFSZ), out_ep_num);
@@ -469,6 +543,27 @@ static void mtu3_mem_free(struct mtu3 *mtu)
kfree(mtu->ep_array);
}
+static void mtu3_set_speed(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+
+ if (!mtu->is_u3_ip && (mtu->max_speed > USB_SPEED_HIGH))
+ mtu->max_speed = USB_SPEED_HIGH;
+
+ if (mtu->max_speed == USB_SPEED_FULL) {
+ /* disable U3 SS function */
+ mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
+ /* disable HS function */
+ mtu3_clrbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+ } else if (mtu->max_speed == USB_SPEED_HIGH) {
+ mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
+ /* HS/FS detected by HW */
+ mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+ }
+ dev_info(mtu->dev, "max_speed: %s\n",
+ usb_speed_string(mtu->max_speed));
+}
+
static void mtu3_regs_init(struct mtu3 *mtu)
{
@@ -478,9 +573,16 @@ static void mtu3_regs_init(struct mtu3 *mtu)
mtu3_intr_disable(mtu);
mtu3_intr_status_clear(mtu);
- mtu3_clrbits(mbase, U3D_USB3_CONFIG, USB3_EN);
- /* HS/FS detected by HW */
- mtu3_setbits(mbase, U3D_POWER_MANAGEMENT, HS_ENABLE);
+ if (mtu->is_u3_ip) {
+ /* disable LGO_U1/U2 by default */
+ mtu3_clrbits(mbase, U3D_LINK_POWER_CONTROL,
+ SW_U1_ACCEPT_ENABLE | SW_U2_ACCEPT_ENABLE |
+ SW_U1_REQUEST_ENABLE | SW_U2_REQUEST_ENABLE);
+ /* device responses to u3_exit from host automatically */
+ mtu3_clrbits(mbase, U3D_LTSSM_CTRL, SOFT_U3_EXIT_EN);
+ }
+
+ mtu3_set_speed(mtu);
/* delay about 0.1us from detecting reset to send chirp-K */
mtu3_clrbits(mbase, U3D_LINK_RESET_INFO, WTCHRP_MSK);
@@ -530,6 +632,10 @@ static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
mtu3_setbits(mbase, U3D_POWER_MANAGEMENT,
LPM_BESL_STALL | LPM_BESLD_STALL);
break;
+ case MTU3_SPEED_SUPER:
+ udev_speed = USB_SPEED_SUPER;
+ maxpkt = 512;
+ break;
default:
udev_speed = USB_SPEED_UNKNOWN;
break;
@@ -548,6 +654,34 @@ static irqreturn_t mtu3_link_isr(struct mtu3 *mtu)
return IRQ_HANDLED;
}
+static irqreturn_t mtu3_u3_ltssm_isr(struct mtu3 *mtu)
+{
+ void __iomem *mbase = mtu->mac_base;
+ u32 ltssm;
+
+ ltssm = mtu3_readl(mbase, U3D_LTSSM_INTR);
+ ltssm &= mtu3_readl(mbase, U3D_LTSSM_INTR_ENABLE);
+ mtu3_writel(mbase, U3D_LTSSM_INTR, ltssm); /* W1C */
+ dev_dbg(mtu->dev, "=== LTSSM[%x] ===\n", ltssm);
+
+ if (ltssm & (HOT_RST_INTR | WARM_RST_INTR))
+ mtu3_gadget_reset(mtu);
+
+ if (ltssm & VBUS_FALL_INTR)
+ mtu3_ss_func_set(mtu, false);
+
+ if (ltssm & VBUS_RISE_INTR)
+ mtu3_ss_func_set(mtu, true);
+
+ if (ltssm & EXIT_U3_INTR)
+ mtu3_gadget_resume(mtu);
+
+ if (ltssm & ENTER_U3_INTR)
+ mtu3_gadget_suspend(mtu);
+
+ return IRQ_HANDLED;
+}
+
static irqreturn_t mtu3_u2_common_isr(struct mtu3 *mtu)
{
void __iomem *mbase = mtu->mac_base;
@@ -588,6 +722,9 @@ irqreturn_t mtu3_irq(int irq, void *data)
if (level1 & MAC2_INTR)
mtu3_u2_common_isr(mtu);
+ if (level1 & MAC3_INTR)
+ mtu3_u3_ltssm_isr(mtu);
+
if (level1 & BMU_INTR)
mtu3_ep0_isr(mtu);
@@ -633,6 +770,27 @@ int ssusb_gadget_init(struct mtu3 *mtu)
struct device *dev = mtu->dev;
int ret;
+ mtu->max_speed = usb_get_maximum_speed(dev);
+
+ /* check the max_speed parameter */
+ switch (mtu->max_speed) {
+ case USB_SPEED_FULL:
+ case USB_SPEED_HIGH:
+ case USB_SPEED_SUPER:
+ break;
+ default:
+ dev_err(dev, "invalid max_speed: %s\n",
+ usb_speed_string(mtu->max_speed));
+ /* fall through */
+ case USB_SPEED_UNKNOWN:
+ /* default as SS */
+ mtu->max_speed = USB_SPEED_SUPER;
+ break;
+ }
+
+ dev_dbg(dev, "mac_base=0x%p, ippc_base=0x%p\n",
+ mtu->mac_base, mtu->ippc_base);
+
ret = mtu3_hw_init(mtu);
if (ret) {
dev_err(dev, "mtu3 hw init failed:%d\n", ret);
diff --git a/drivers/usb/mtu3/mtu3_gadget.c b/drivers/usb/mtu3/mtu3_gadget.c
index 0e25e0f..84f3fe1 100644
--- a/drivers/usb/mtu3/mtu3_gadget.c
+++ b/drivers/usb/mtu3/mtu3_gadget.c
@@ -73,6 +73,7 @@ static void nuke(struct mtu3_ep *mep, const int status)
static int mtu3_ep_enable(struct mtu3_ep *mep)
{
const struct usb_endpoint_descriptor *desc;
+ const struct usb_ss_ep_comp_descriptor *comp_desc;
struct mtu3 *mtu = mep->mtu;
u32 interval = 0;
u32 mult = 0;
@@ -81,11 +82,24 @@ static int mtu3_ep_enable(struct mtu3_ep *mep)
int ret;
desc = mep->desc;
+ comp_desc = mep->comp_desc;
mep->type = usb_endpoint_type(desc);
max_packet = usb_endpoint_maxp(desc);
mep->maxp = max_packet & GENMASK(10, 0);
switch (mtu->g.speed) {
+ case USB_SPEED_SUPER:
+ if (usb_endpoint_xfer_int(desc) ||
+ usb_endpoint_xfer_isoc(desc)) {
+ interval = desc->bInterval;
+ interval = clamp_val(interval, 1, 16) - 1;
+ if (usb_endpoint_xfer_isoc(desc) && comp_desc)
+ mult = comp_desc->bmAttributes;
+ }
+ if (comp_desc)
+ burst = comp_desc->bMaxBurst;
+
+ break;
case USB_SPEED_HIGH:
if (usb_endpoint_xfer_isoc(desc) ||
usb_endpoint_xfer_int(desc)) {
@@ -103,6 +117,7 @@ static int mtu3_ep_enable(struct mtu3_ep *mep)
mep->ep.maxpacket = mep->maxp;
mep->ep.desc = desc;
+ mep->ep.comp_desc = comp_desc;
/* slot mainly affects bulk/isoc transfer, so ignore int */
mep->slot = usb_endpoint_xfer_int(desc) ? 0 : mtu->slot;
@@ -135,6 +150,7 @@ static int mtu3_ep_disable(struct mtu3_ep *mep)
mep->desc = NULL;
mep->ep.desc = NULL;
+ mep->comp_desc = NULL;
mep->type = 0;
mep->flags = 0;
@@ -178,6 +194,7 @@ static int mtu3_gadget_ep_enable(struct usb_ep *ep,
spin_lock_irqsave(&mtu->lock, flags);
mep->desc = desc;
+ mep->comp_desc = ep->comp_desc;
ret = mtu3_ep_enable(mep);
if (ret)
@@ -439,13 +456,15 @@ static int mtu3_gadget_wakeup(struct usb_gadget *gadget)
return -EOPNOTSUPP;
spin_lock_irqsave(&mtu->lock, flags);
-
- mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
- spin_unlock_irqrestore(&mtu->lock, flags);
- usleep_range(10000, 11000);
- spin_lock_irqsave(&mtu->lock, flags);
- mtu3_clrbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
-
+ if (mtu->g.speed == USB_SPEED_SUPER) {
+ mtu3_setbits(mtu->mac_base, U3D_LINK_POWER_CONTROL, UX_EXIT);
+ } else {
+ mtu3_setbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
+ spin_unlock_irqrestore(&mtu->lock, flags);
+ usleep_range(10000, 11000);
+ spin_lock_irqsave(&mtu->lock, flags);
+ mtu3_clrbits(mtu->mac_base, U3D_POWER_MANAGEMENT, RESUME);
+ }
spin_unlock_irqrestore(&mtu->lock, flags);
return 0;
}
@@ -476,7 +495,7 @@ static int mtu3_gadget_pullup(struct usb_gadget *gadget, int is_on)
mtu->softconnect = is_on;
} else if (is_on != mtu->softconnect) {
mtu->softconnect = is_on;
- mtu3_hs_softconn_set(mtu, is_on);
+ mtu3_dev_on_off(mtu, is_on);
}
spin_unlock_irqrestore(&mtu->lock, flags);
@@ -524,7 +543,7 @@ static void stop_activity(struct mtu3 *mtu)
/* deactivate the hardware */
if (mtu->softconnect) {
mtu->softconnect = 0;
- mtu3_hs_softconn_set(mtu, 0);
+ mtu3_dev_on_off(mtu, 0);
}
/*
@@ -587,14 +606,14 @@ static void init_hw_ep(struct mtu3 *mtu, struct mtu3_ep *mep,
mep->ep.name = mep->name;
INIT_LIST_HEAD(&mep->ep.ep_list);
- /* initialize maxpacket as HS */
+ /* initialize maxpacket as SS */
if (!epnum) {
- usb_ep_set_maxpacket_limit(&mep->ep, 64);
+ usb_ep_set_maxpacket_limit(&mep->ep, 512);
mep->ep.caps.type_control = true;
mep->ep.ops = &mtu3_ep0_ops;
mtu->g.ep0 = &mep->ep;
} else {
- usb_ep_set_maxpacket_limit(&mep->ep, 512);
+ usb_ep_set_maxpacket_limit(&mep->ep, 1024);
mep->ep.caps.type_iso = true;
mep->ep.caps.type_bulk = true;
mep->ep.caps.type_int = true;
@@ -637,7 +656,7 @@ int mtu3_gadget_setup(struct mtu3 *mtu)
int ret;
mtu->g.ops = &mtu3_gadget_ops;
- mtu->g.max_speed = USB_SPEED_HIGH;
+ mtu->g.max_speed = mtu->max_speed;
mtu->g.speed = USB_SPEED_UNKNOWN;
mtu->g.sg_supported = 0;
mtu->g.name = MTU3_DRIVER_NAME;
diff --git a/drivers/usb/mtu3/mtu3_gadget_ep0.c b/drivers/usb/mtu3/mtu3_gadget_ep0.c
index 4e2c2bab..2d7427b 100644
--- a/drivers/usb/mtu3/mtu3_gadget_ep0.c
+++ b/drivers/usb/mtu3/mtu3_gadget_ep0.c
@@ -161,6 +161,41 @@ static void ep0_stall_set(struct mtu3_ep *mep0, bool set, u32 pktrdy)
static void ep0_dummy_complete(struct usb_ep *ep, struct usb_request *req)
{}
+static void ep0_set_sel_complete(struct usb_ep *ep, struct usb_request *req)
+{
+ struct mtu3_request *mreq;
+ struct mtu3 *mtu;
+ struct usb_set_sel_req sel;
+
+ memcpy(&sel, req->buf, sizeof(sel));
+
+ mreq = to_mtu3_request(req);
+ mtu = mreq->mtu;
+ dev_dbg(mtu->dev, "u1sel:%d, u1pel:%d, u2sel:%d, u2pel:%d\n",
+ sel.u1_sel, sel.u1_pel, sel.u2_sel, sel.u2_pel);
+}
+
+/* queue data stage to handle 6 byte SET_SEL request */
+static int ep0_set_sel(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
+{
+ int ret;
+ u16 length = le16_to_cpu(setup->wLength);
+
+ if (unlikely(length != 6)) {
+ dev_err(mtu->dev, "%s wrong wLength:%d\n",
+ __func__, length);
+ return -EINVAL;
+ }
+
+ mtu->ep0_req.mep = mtu->ep0;
+ mtu->ep0_req.request.length = 6;
+ mtu->ep0_req.request.buf = mtu->setup_buf;
+ mtu->ep0_req.request.complete = ep0_set_sel_complete;
+ ret = ep0_queue(mtu->ep0, &mtu->ep0_req);
+
+ return ret < 0 ? ret : 1;
+}
+
static int
ep0_get_status(struct mtu3 *mtu, const struct usb_ctrlrequest *setup)
{
@@ -174,6 +209,15 @@ static void ep0_dummy_complete(struct usb_ep *ep, struct usb_request *req)
case USB_RECIP_DEVICE:
result[0] = mtu->is_self_powered << USB_DEVICE_SELF_POWERED;
result[0] |= mtu->may_wakeup << USB_DEVICE_REMOTE_WAKEUP;
+ /* superspeed only */
+ if (mtu->g.speed == USB_SPEED_SUPER) {
+ result[0] |= mtu->u1_enable << USB_DEV_STAT_U1_ENABLED;
+ result[0] |= mtu->u2_enable << USB_DEV_STAT_U2_ENABLED;
+ }
+
+ dev_dbg(mtu->dev, "%s result=%x, U1=%x, U2=%x\n", __func__,
+ result[0], mtu->u1_enable, mtu->u2_enable);
+
break;
case USB_RECIP_INTERFACE:
break;
@@ -265,7 +309,9 @@ static int handle_test_mode(struct mtu3 *mtu, struct usb_ctrlrequest *setup)
static int ep0_handle_feature_dev(struct mtu3 *mtu,
struct usb_ctrlrequest *setup, bool set)
{
+ void __iomem *mbase = mtu->mac_base;
int handled = -EINVAL;
+ u32 lpc;
switch (le16_to_cpu(setup->wValue)) {
case USB_DEVICE_REMOTE_WAKEUP:
@@ -279,6 +325,36 @@ static int ep0_handle_feature_dev(struct mtu3 *mtu,
handled = handle_test_mode(mtu, setup);
break;
+ case USB_DEVICE_U1_ENABLE:
+ if (mtu->g.speed != USB_SPEED_SUPER ||
+ mtu->g.state != USB_STATE_CONFIGURED)
+ break;
+
+ lpc = mtu3_readl(mbase, U3D_LINK_POWER_CONTROL);
+ if (set)
+ lpc |= SW_U1_ACCEPT_ENABLE;
+ else
+ lpc &= ~SW_U1_ACCEPT_ENABLE;
+ mtu3_writel(mbase, U3D_LINK_POWER_CONTROL, lpc);
+
+ mtu->u1_enable = !!set;
+ handled = 1;
+ break;
+ case USB_DEVICE_U2_ENABLE:
+ if (mtu->g.speed != USB_SPEED_SUPER ||
+ mtu->g.state != USB_STATE_CONFIGURED)
+ break;
+
+ lpc = mtu3_readl(mbase, U3D_LINK_POWER_CONTROL);
+ if (set)
+ lpc |= SW_U2_ACCEPT_ENABLE;
+ else
+ lpc &= ~SW_U2_ACCEPT_ENABLE;
+ mtu3_writel(mbase, U3D_LINK_POWER_CONTROL, lpc);
+
+ mtu->u2_enable = !!set;
+ handled = 1;
+ break;
default:
handled = -EINVAL;
break;
@@ -303,6 +379,17 @@ static int ep0_handle_feature(struct mtu3 *mtu,
case USB_RECIP_DEVICE:
handled = ep0_handle_feature_dev(mtu, setup, set);
break;
+ case USB_RECIP_INTERFACE:
+ /* superspeed only */
+ if ((value == USB_INTRF_FUNC_SUSPEND)
+ && (mtu->g.speed == USB_SPEED_SUPER)) {
+ /*
+ * forward the request because function drivers
+ * should handle it
+ */
+ handled = 0;
+ }
+ break;
case USB_RECIP_ENDPOINT:
epnum = index & USB_ENDPOINT_NUMBER_MASK;
if (epnum == 0 || epnum >= mtu->num_eps ||
@@ -390,6 +477,9 @@ static int handle_standard_request(struct mtu3 *mtu,
case USB_REQ_GET_STATUS:
handled = ep0_get_status(mtu, setup);
break;
+ case USB_REQ_SET_SEL:
+ handled = ep0_set_sel(mtu, setup);
+ break;
case USB_REQ_SET_ISOCH_DELAY:
handled = 1;
break;
diff --git a/drivers/usb/mtu3/mtu3_hw_regs.h b/drivers/usb/mtu3/mtu3_hw_regs.h
index 08c83c5..2123672 100644
--- a/drivers/usb/mtu3/mtu3_hw_regs.h
+++ b/drivers/usb/mtu3/mtu3_hw_regs.h
@@ -260,13 +260,46 @@
/*---------------- SSUSB_USB3_MAC_CSR REGISTER DEFINITION ----------------*/
+#define U3D_LTSSM_CTRL (SSUSB_USB3_MAC_CSR_BASE + 0x0010)
#define U3D_USB3_CONFIG (SSUSB_USB3_MAC_CSR_BASE + 0x001C)
+#define U3D_LTSSM_INTR_ENABLE (SSUSB_USB3_MAC_CSR_BASE + 0x013C)
+#define U3D_LTSSM_INTR (SSUSB_USB3_MAC_CSR_BASE + 0x0140)
+
/*---------------- SSUSB_USB3_MAC_CSR FIELD DEFINITION ----------------*/
+/* U3D_LTSSM_CTRL */
+#define FORCE_POLLING_FAIL BIT(4)
+#define FORCE_RXDETECT_FAIL BIT(3)
+#define SOFT_U3_EXIT_EN BIT(2)
+#define COMPLIANCE_EN BIT(1)
+#define U1_GO_U2_EN BIT(0)
+
/* U3D_USB3_CONFIG */
#define USB3_EN BIT(0)
+/* U3D_LTSSM_INTR_ENABLE */
+/* U3D_LTSSM_INTR */
+#define U3_RESUME_INTR BIT(18)
+#define U3_LFPS_TMOUT_INTR BIT(17)
+#define VBUS_FALL_INTR BIT(16)
+#define VBUS_RISE_INTR BIT(15)
+#define RXDET_SUCCESS_INTR BIT(14)
+#define EXIT_U3_INTR BIT(13)
+#define EXIT_U2_INTR BIT(12)
+#define EXIT_U1_INTR BIT(11)
+#define ENTER_U3_INTR BIT(10)
+#define ENTER_U2_INTR BIT(9)
+#define ENTER_U1_INTR BIT(8)
+#define ENTER_U0_INTR BIT(7)
+#define RECOVERY_INTR BIT(6)
+#define WARM_RST_INTR BIT(5)
+#define HOT_RST_INTR BIT(4)
+#define LOOPBACK_INTR BIT(3)
+#define COMPLIANCE_INTR BIT(2)
+#define SS_DISABLE_INTR BIT(1)
+#define SS_INACTIVE_INTR BIT(0)
+
/*---------------- SSUSB_USB3_SYS_CSR REGISTER DEFINITION ----------------*/
#define U3D_LINK_UX_INACT_TIMER (SSUSB_USB3_SYS_CSR_BASE + 0x020C)
--
1.7.9.5
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox