* [PATCH V6 3/4] drm/bridge: Add driver for GE B850v3 LVDS/DP++ Bridge
From: Philipp Zabel @ 2016-11-01 11:39 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cbdd043a504a10a8f77fedb25d0f62dd8b837aca.1477572814.git.peter.senna@collabora.com>
Hi Peter,
Am Donnerstag, den 27.10.2016, 15:01 +0200 schrieb Peter Senna Tschudin:
> Add a driver that create a drm_bridge and a drm_connector for the LVDS
> to DP++ display bridge of the GE B850v3.
>
> There are two physical bridges on the video signal pipeline: a
> STDP4028(LVDS to DP) and a STDP2690(DP to DP++). The hardware and
> firmware made it complicated for this binding to comprise two device
> tree nodes, as the design goal is to configure both bridges based on
> the LVDS signal, which leave the driver powerless to control the video
> processing pipeline. The two bridges behaves as a single bridge, and
> the driver is only needed for telling the host about EDID / HPD, and
> for giving the host powers to ack interrupts. The video signal pipeline
> is as follows:
>
> Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
>
> Cc: Martyn Welch <martyn.welch@collabora.co.uk>
> Cc: Martin Donnelly <martin.donnelly@ge.com>
> Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
> Cc: Enric Balletbo i Serra <enric.balletbo@collabora.com>
> Cc: Philipp Zabel <p.zabel@pengutronix.de>
> Cc: Rob Herring <robh@kernel.org>
> Cc: Fabio Estevam <fabio.estevam@nxp.com>
> CC: David Airlie <airlied@linux.ie>
> CC: Thierry Reding <treding@nvidia.com>
> CC: Thierry Reding <thierry.reding@gmail.com>
> CC: Archit Taneja <architt@codeaurora.org>
> Reviewed-by: Enric Balletbo <enric.balletbo@collabora.com>
> Signed-off-by: Peter Senna Tschudin <peter.senna@collabora.com>
> ---
> Changes from V5:
> - Reworked interrupt handler initialization
> - Removed useless calls to: drm_connector_register(),
> drm_helper_hpd_irq_event(), and drm_bridge_enable()
>
> Changes from V4:
> - Renamed the i2c_driver.name from "ge,b850v3-lvds-dp" to "b850v3-lvds-dp" to
> remove the comma from the driver name
>
> Changes from V3:
> - 3/4 instead of 4/5
> - Tested on next-20160804
>
> Changes from V2:
> - Made it atomic to be applied on next-20160729 on top of Liu Ying changes
> that made imx-ldb atomic
>
> Changes from V1:
> - New commit message
> - Removed 3 empty entry points
> - Removed memory leak from ge_b850v3_lvds_dp_get_modes()
> - Added a lock for mode setting
> - Removed a few blank lines
> - Changed the order at Makefile and Kconfig
>
> drivers/gpu/drm/bridge/Kconfig | 11 +
> drivers/gpu/drm/bridge/Makefile | 1 +
> drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c | 395 +++++++++++++++++++++++++++++
> 3 files changed, 407 insertions(+)
> create mode 100644 drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
>
> diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
> index bd6acc8..1d02422 100644
> --- a/drivers/gpu/drm/bridge/Kconfig
> +++ b/drivers/gpu/drm/bridge/Kconfig
> @@ -39,6 +39,17 @@ config DRM_DW_HDMI_AHB_AUDIO
> Designware HDMI block. This is used in conjunction with
> the i.MX6 HDMI driver.
>
> +config DRM_GE_B850V3_LVDS_DP
> + tristate "GE B850v3 LVDS to DP++ display bridge"
> + depends on OF
> + select DRM_KMS_HELPER
> + select DRM_PANEL
> + ---help---
> + This is a driver for the display bridge of
> + GE B850v3 that convert dual channel LVDS
> + to DP++. This is used with the i.MX6 imx-ldb
> + driver.
> +
> config DRM_NXP_PTN3460
> tristate "NXP PTN3460 DP/LVDS bridge"
> depends on OF
> diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
> index 97ed1a5..b6b44a5 100644
> --- a/drivers/gpu/drm/bridge/Makefile
> +++ b/drivers/gpu/drm/bridge/Makefile
> @@ -5,6 +5,7 @@ obj-$(CONFIG_DRM_DUMB_VGA_DAC) += dumb-vga-dac.o
> obj-$(CONFIG_DRM_DW_HDMI) += dw-hdmi.o
> obj-$(CONFIG_DRM_DW_HDMI_AHB_AUDIO) += dw-hdmi-ahb-audio.o
> obj-$(CONFIG_DRM_NXP_PTN3460) += nxp-ptn3460.o
> +obj-$(CONFIG_DRM_GE_B850V3_LVDS_DP) += ge_b850v3_lvds_dp.o
> obj-$(CONFIG_DRM_PARADE_PS8622) += parade-ps8622.o
> obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
> obj-$(CONFIG_DRM_SII902X) += sii902x.o
> diff --git a/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> new file mode 100644
> index 0000000..85875d8
> --- /dev/null
> +++ b/drivers/gpu/drm/bridge/ge_b850v3_lvds_dp.c
> @@ -0,0 +1,395 @@
> +/*
> + * Driver for GE B850v3 DP display bridge
> +
> + * Copyright (c) 2016, Collabora Ltd.
> + * Copyright (c) 2016, General Electric Company
> +
> + * This program is free software; you can redistribute it and/or modify it
> + * under the terms and conditions of the GNU General Public License,
> + * version 2, as published by the Free Software Foundation.
> +
> + * This program is distributed in the hope it will be useful, but WITHOUT
> + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
> + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
> + * more details.
> +
> + * You should have received a copy of the GNU General Public License
> + * along with this program. If not, see <http://www.gnu.org/licenses/>.
> +
> + * This driver creates a drm_bridge and a drm_connector for the LVDS to DP++
> + * display bridge of the GE B850v3. There are two physical bridges on the video
> + * signal pipeline: a STDP4028(LVDS to DP) and a STDP2690(DP to DP++). However
> + * the physical bridges are automatically configured by the input video signal,
> + * and the driver has no access to the video processing pipeline. The driver is
> + * only needed to read EDID from the STDP2690 and to handle HPD events from the
> + * STDP4028. The driver communicates with both bridges over i2c. The video
> + * signal pipeline is as follows:
> + *
> + * Host -> LVDS|--(STDP4028)--|DP -> DP|--(STDP2690)--|DP++ -> Video output
> + *
> + */
> +
> +#include <linux/gpio.h>
> +#include <linux/i2c.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <drm/drm_atomic.h>
> +#include <drm/drm_atomic_helper.h>
> +#include <drm/drm_crtc_helper.h>
> +#include <drm/drm_edid.h>
> +#include <drm/drmP.h>
> +
> +/*
> + * 220Mhz is a limitation of the host, as the bridge is capable of up to
> + * 330Mhz. See section 9.2.1.2.4 of the i.MX 6Dual/6Quad Applications
> + * Processor Reference Manual for more information about the 220Mhz limit.
> + * The imx-ldb driver will warn about clocks over 170Mhz, but it seem to work
> + * fine.
> + */
> +#define MAX_PIXEL_CLOCK 220000
That is a limitation of the IPU DI pixel clock rate if both DIs are
active. If only a single DI is active, this limit is 264 MHz on i.MX6Q.
The LDB pixel clock rate maximum is 170 MHz if only a single LDB channel
is active.
I currently see no way for the crtc and encoder code to have a say about
maximum pixel clocks when pruning the mode list in .fill_modes.
> +
> +#define EDID_EXT_BLOCK_CNT 0x7E
> +
> +#define STDP4028_IRQ_OUT_CONF_REG 0x02
> +#define STDP4028_DPTX_IRQ_EN_REG 0x3C
> +#define STDP4028_DPTX_IRQ_STS_REG 0x3D
> +#define STDP4028_DPTX_STS_REG 0x3E
> +
> +#define STDP4028_DPTX_DP_IRQ_EN 0x1000
> +
> +#define STDP4028_DPTX_HOTPLUG_IRQ_EN 0x0400
> +#define STDP4028_DPTX_LINK_CH_IRQ_EN 0x2000
> +#define STDP4028_DPTX_IRQ_CONFIG \
> + (STDP4028_DPTX_LINK_CH_IRQ_EN | STDP4028_DPTX_HOTPLUG_IRQ_EN)
> +
> +#define STDP4028_DPTX_HOTPLUG_STS 0x0200
> +#define STDP4028_DPTX_LINK_STS 0x1000
> +#define STDP4028_CON_STATE_CONNECTED \
> + (STDP4028_DPTX_HOTPLUG_STS | STDP4028_DPTX_LINK_STS)
> +
> +#define STDP4028_DPTX_HOTPLUG_CH_STS 0x0400
> +#define STDP4028_DPTX_LINK_CH_STS 0x2000
> +#define STDP4028_DPTX_IRQ_CLEAR \
> + (STDP4028_DPTX_LINK_CH_STS | STDP4028_DPTX_HOTPLUG_CH_STS)
> +
> +struct ge_b850v3_lvds_dp {
> + struct drm_connector connector;
> + struct drm_bridge bridge;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c;
> + struct i2c_client *edid_i2c;
> + struct edid *edid;
> + struct mutex lock;
> +};
> +
> +static inline struct ge_b850v3_lvds_dp *
> + bridge_to_ge_b850v3_lvds_dp(struct drm_bridge *bridge)
> +{
> + return container_of(bridge, struct ge_b850v3_lvds_dp, bridge);
> +}
> +
> +static inline struct ge_b850v3_lvds_dp *
> + connector_to_ge_b850v3_lvds_dp(struct drm_connector *connector)
> +{
> + return container_of(connector, struct ge_b850v3_lvds_dp, connector);
> +}
> +
> +u8 *stdp2690_get_edid(struct i2c_client *client)
> +{
> + struct i2c_adapter *adapter = client->adapter;
> + unsigned char start = 0x00;
> + unsigned int total_size;
> + u8 *block = kmalloc(EDID_LENGTH, GFP_KERNEL);
> +
> + struct i2c_msg msgs[] = {
> + {
> + .addr = client->addr,
> + .flags = 0,
> + .len = 1,
> + .buf = &start,
> + }, {
> + .addr = client->addr,
> + .flags = I2C_M_RD,
> + .len = EDID_LENGTH,
> + .buf = block,
> + }
> + };
> +
> + if (!block)
> + return NULL;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID.\n");
> + goto err;
> + }
> +
> + if (!drm_edid_block_valid(block, 0, false, NULL)) {
> + DRM_ERROR("Invalid EDID block\n");
> + goto err;
> + }
> +
> + total_size = (block[EDID_EXT_BLOCK_CNT] + 1) * EDID_LENGTH;
> + if (total_size > EDID_LENGTH) {
> + kfree(block);
> + block = kmalloc(total_size, GFP_KERNEL);
> + if (!block)
> + return NULL;
> +
> + /* Yes, read the entire buffer, and do not skip the first
> + * EDID_LENGTH bytes.
> + */
> + start = 0x00;
> + msgs[1].len = total_size;
> + msgs[1].buf = block;
> +
> + if (i2c_transfer(adapter, msgs, 2) != 2) {
> + DRM_ERROR("Unable to read EDID extension blocks.\n");
> + goto err;
> + }
> + }
> +
> + return block;
> +
> +err:
> + kfree(block);
> + return NULL;
> +}
> +
> +static int ge_b850v3_lvds_dp_get_modes(struct drm_connector *connector)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + struct i2c_client *client;
> + int num_modes = 0;
> +
> + ptn_bridge = connector_to_ge_b850v3_lvds_dp(connector);
> + client = ptn_bridge->edid_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
What does this lock protect?
> + kfree(ptn_bridge->edid);
> + ptn_bridge->edid = (struct edid *) stdp2690_get_edid(client);
> +
> + if (ptn_bridge->edid) {
> + drm_mode_connector_update_edid_property(connector,
> + ptn_bridge->edid);
> + num_modes = drm_add_edid_modes(connector, ptn_bridge->edid);
> + }
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + return num_modes;
> +}
> +
> +
> +static enum drm_mode_status ge_b850v3_lvds_dp_mode_valid(
> + struct drm_connector *connector, struct drm_display_mode *mode)
> +{
> + if (mode->clock > MAX_PIXEL_CLOCK) {
> + DRM_INFO("The pixel clock for the mode %s is too high, and not supported.",
> + mode->name);
> + return MODE_CLOCK_HIGH;
> + }
> +
> + return MODE_OK;
> +}
> +
> +static const struct
> +drm_connector_helper_funcs ge_b850v3_lvds_dp_connector_helper_funcs = {
> + .get_modes = ge_b850v3_lvds_dp_get_modes,
> + .mode_valid = ge_b850v3_lvds_dp_mode_valid,
> +};
> +
> +static enum drm_connector_status ge_b850v3_lvds_dp_detect(
> + struct drm_connector *connector, bool force)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + connector_to_ge_b850v3_lvds_dp(connector);
> + struct i2c_client *ge_b850v3_lvds_dp_i2c =
> + ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + s32 link_state;
> +
> + link_state = i2c_smbus_read_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_STS_REG);
> +
> + if (link_state == STDP4028_CON_STATE_CONNECTED)
> + return connector_status_connected;
> +
> + if (link_state == 0)
> + return connector_status_disconnected;
> +
> + return connector_status_unknown;
> +}
> +
> +static const struct drm_connector_funcs ge_b850v3_lvds_dp_connector_funcs = {
> + .dpms = drm_atomic_helper_connector_dpms,
> + .fill_modes = drm_helper_probe_single_connector_modes,
> + .detect = ge_b850v3_lvds_dp_detect,
> + .destroy = drm_connector_cleanup,
> + .reset = drm_atomic_helper_connector_reset,
> + .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
> + .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
> +};
> +
> +static irqreturn_t ge_b850v3_lvds_dp_irq_handler(int irq, void *dev_id)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge = dev_id;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> +
> + mutex_lock(&ptn_bridge->lock);
And what does this lock protect here?
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + mutex_unlock(&ptn_bridge->lock);
> +
> + if (ptn_bridge->connector.dev)
> + drm_kms_helper_hotplug_event(ptn_bridge->connector.dev);
> +
> + return IRQ_HANDLED;
> +}
> +
> +static int ge_b850v3_lvds_dp_attach(struct drm_bridge *bridge)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge
> + = bridge_to_ge_b850v3_lvds_dp(bridge);
> + struct drm_connector *connector = &ptn_bridge->connector;
> + struct i2c_client *ge_b850v3_lvds_dp_i2c
> + = ptn_bridge->ge_b850v3_lvds_dp_i2c;
> + int ret;
> +
> + if (!bridge->encoder) {
> + DRM_ERROR("Parent encoder object not found");
> + return -ENODEV;
> + }
> +
> + connector->polled = DRM_CONNECTOR_POLL_HPD;
> +
> + drm_connector_helper_add(connector,
> + &ge_b850v3_lvds_dp_connector_helper_funcs);
> +
> + ret = drm_connector_init(bridge->dev, connector,
> + &ge_b850v3_lvds_dp_connector_funcs,
> + DRM_MODE_CONNECTOR_DisplayPort);
> + if (ret) {
> + DRM_ERROR("Failed to initialize connector with drm\n");
> + return ret;
> + }
> +
> + ret = drm_mode_connector_attach_encoder(connector, bridge->encoder);
> + if (ret)
> + return ret;
> +
> + /* Configures the bridge to re-enable interrupts after each ack. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_IRQ_OUT_CONF_REG, STDP4028_DPTX_DP_IRQ_EN);
> +
> + /* Enable interrupts */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_EN_REG, STDP4028_DPTX_IRQ_CONFIG);
> +
> + return 0;
> +}
> +
> +static const struct drm_bridge_funcs ge_b850v3_lvds_dp_funcs = {
> + .attach = ge_b850v3_lvds_dp_attach,
What about .detach? Should the interrupt be disabled?
> +};
> +
> +static int ge_b850v3_lvds_dp_probe(struct i2c_client *ge_b850v3_lvds_dp_i2c,
> + const struct i2c_device_id *id)
> +{
> + struct device *dev = &ge_b850v3_lvds_dp_i2c->dev;
> + struct ge_b850v3_lvds_dp *ptn_bridge;
> + int ret;
> + u32 edid_i2c_reg;
> +
> + ptn_bridge = devm_kzalloc(dev, sizeof(*ptn_bridge), GFP_KERNEL);
> + if (!ptn_bridge)
> + return -ENOMEM;
> +
> + mutex_init(&ptn_bridge->lock);
> +
> + ptn_bridge->ge_b850v3_lvds_dp_i2c = ge_b850v3_lvds_dp_i2c;
> + ptn_bridge->bridge.driver_private = ptn_bridge;
> + i2c_set_clientdata(ge_b850v3_lvds_dp_i2c, ptn_bridge);
> +
> + ret = of_property_read_u32(dev->of_node, "edid-reg", &edid_i2c_reg);
> + if (ret) {
> + dev_err(dev, "edid-reg not specified, aborting...\n");
> + return -ENODEV;
> + }
> +
> + ptn_bridge->edid_i2c = devm_kzalloc(dev,
> + sizeof(struct i2c_client), GFP_KERNEL);
> +
Superfluous empty line, but ...
> + if (!ptn_bridge->edid_i2c)
> + return -ENOMEM;
> +
> + memcpy(ptn_bridge->edid_i2c, ge_b850v3_lvds_dp_i2c,
> + sizeof(struct i2c_client));
> +
> + ptn_bridge->edid_i2c->addr = (unsigned short) edid_i2c_reg;
... this looks to me like you should use i2c_new_dummy, or rather
i2c_new_secondary_device instead. For the latter you'd have to change
the bindings to use reg and reg-names properties instead of the custom
edid-reg property.
> +
> + ptn_bridge->bridge.funcs = &ge_b850v3_lvds_dp_funcs;
> + ptn_bridge->bridge.of_node = dev->of_node;
> + ret = drm_bridge_add(&ptn_bridge->bridge);
> + if (ret) {
> + DRM_ERROR("Failed to add bridge\n");
> + return ret;
> + }
Just as a note, this currently can not fail. It's just a list_add_tail
under a mutex lock.
If it would fail though, it'd be nice to also print the error code.
> +
> + /* Clear pending interrupts since power up. */
> + i2c_smbus_write_word_data(ge_b850v3_lvds_dp_i2c,
> + STDP4028_DPTX_IRQ_STS_REG, STDP4028_DPTX_IRQ_CLEAR);
> +
> + if (ge_b850v3_lvds_dp_i2c->irq) {
> + ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
> + ge_b850v3_lvds_dp_i2c->irq, NULL,
> + ge_b850v3_lvds_dp_irq_handler,
> + IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
> + "ge-b850v3-lvds-dp", ptn_bridge);
> + if (ret)
> + return ret;
> + }
> +
> + return 0;
Maybe a matter of taste, but this could be changed to:
/* If no interrupt has to be requested, we're done here */
if (!ge_b850v3_lvds_dp_i2c->irq)
return 0;
return devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
or, as we know ret to be 0 after the call to drm_bridge_add:
if (ge_b850v3_lvds_dp_i2c->irq) {
ret = devm_request_threaded_irq(&ge_b850v3_lvds_dp_i2c->dev,
ge_b850v3_lvds_dp_i2c->irq, NULL,
ge_b850v3_lvds_dp_irq_handler,
IRQF_TRIGGER_HIGH | IRQF_ONESHOT,
"ge-b850v3-lvds-dp", ptn_bridge);
}
return ret;
> +}
> +
> +static int ge_b850v3_lvds_dp_remove(struct i2c_client *ge_b850v3_lvds_dp_i2c)
> +{
> + struct ge_b850v3_lvds_dp *ptn_bridge =
> + i2c_get_clientdata(ge_b850v3_lvds_dp_i2c);
> +
> + drm_bridge_remove(&ptn_bridge->bridge);
> +
> + kfree(ptn_bridge->edid);
> +
> + return 0;
> +}
> +
> +static const struct i2c_device_id ge_b850v3_lvds_dp_i2c_table[] = {
> + {"b850v3-lvds-dp", 0},
> + {},
> +};
> +MODULE_DEVICE_TABLE(i2c, ge_b850v3_lvds_dp_i2c_table);
> +
> +static const struct of_device_id ge_b850v3_lvds_dp_match[] = {
> + { .compatible = "ge,b850v3-lvds-dp" },
> + {},
> +};
> +MODULE_DEVICE_TABLE(of, ge_b850v3_lvds_dp_match);
> +
> +static struct i2c_driver ge_b850v3_lvds_dp_driver = {
> + .id_table = ge_b850v3_lvds_dp_i2c_table,
> + .probe = ge_b850v3_lvds_dp_probe,
> + .remove = ge_b850v3_lvds_dp_remove,
> + .driver = {
> + .name = "b850v3-lvds-dp",
> + .of_match_table = ge_b850v3_lvds_dp_match,
> + },
> +};
> +module_i2c_driver(ge_b850v3_lvds_dp_driver);
> +
> +MODULE_AUTHOR("Peter Senna Tschudin <peter.senna@collabora.com>");
> +MODULE_AUTHOR("Martyn Welch <martyn.welch@collabora.co.uk>");
> +MODULE_DESCRIPTION("GE LVDS to DP++ display bridge)");
> +MODULE_LICENSE("GPL v2");
regards
Philipp
^ permalink raw reply
* [PATCH 5/5] ARM: OMAP: kill omap_pmic_init
From: Nicolae Rosia @ 2016-11-01 11:36 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478000206-10855-1-git-send-email-Nicolae_Rosia@mentor.com>
Remove dead code
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
---
arch/arm/mach-omap2/twl-common.c | 13 -------------
arch/arm/mach-omap2/twl-common.h | 2 --
2 files changed, 15 deletions(-)
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index cf3d81b..876772c 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -39,19 +39,6 @@ static struct i2c_board_info __initdata pmic_i2c_board_info = {
.flags = I2C_CLIENT_WAKE,
};
-void __init omap_pmic_init(int bus, u32 clkrate,
- const char *pmic_type, int pmic_irq,
- struct twl4030_platform_data *pmic_data)
-{
- omap_mux_init_signal("sys_nirq", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
- strlcpy(pmic_i2c_board_info.type, pmic_type,
- sizeof(pmic_i2c_board_info.type));
- pmic_i2c_board_info.irq = pmic_irq;
- pmic_i2c_board_info.platform_data = pmic_data;
-
- omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
-}
-
void __init omap_pmic_late_init(void)
{
/* Init the OMAP TWL parameters (if PMIC has been registerd) */
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index 5579bd6..44713bb 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -35,8 +35,6 @@ struct twl6040_platform_data;
struct omap_tw4030_pdata;
struct i2c_board_info;
-void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq,
- struct twl4030_platform_data *pmic_data);
void omap_pmic_late_init(void);
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
--
2.5.5
^ permalink raw reply related
* [PATCH 4/5] ARM: OMAP2: kill omap2_pmic_init
From: Nicolae Rosia @ 2016-11-01 11:36 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478000206-10855-1-git-send-email-Nicolae_Rosia@mentor.com>
Remove dead code
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
---
arch/arm/mach-omap2/twl-common.h | 6 ------
1 file changed, 6 deletions(-)
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index 397722d..5579bd6 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -39,12 +39,6 @@ void omap_pmic_init(int bus, u32 clkrate, const char *pmic_type, int pmic_irq,
struct twl4030_platform_data *pmic_data);
void omap_pmic_late_init(void);
-static inline void omap2_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data)
-{
- omap_pmic_init(2, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
-}
-
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
#endif /* __OMAP_PMIC_COMMON__ */
--
2.5.5
^ permalink raw reply related
* [PATCH 3/5] ARM: OMAP3: kill omap3_pmic_init
From: Nicolae Rosia @ 2016-11-01 11:36 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478000206-10855-1-git-send-email-Nicolae_Rosia@mentor.com>
Remove dead code
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
---
arch/arm/mach-omap2/twl-common.h | 6 ------
1 file changed, 6 deletions(-)
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index 048f6b2..397722d 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -45,12 +45,6 @@ static inline void omap2_pmic_init(const char *pmic_type,
omap_pmic_init(2, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
}
-static inline void omap3_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data)
-{
- omap_pmic_init(1, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
-}
-
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
#endif /* __OMAP_PMIC_COMMON__ */
--
2.5.5
^ permalink raw reply related
* [PATCH 2/5] ARM: OMAP3: kill omap3_pmic_get_config and twl_{get, set}_voltage
From: Nicolae Rosia @ 2016-11-01 11:36 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478000206-10855-1-git-send-email-Nicolae_Rosia@mentor.com>
Remove dead code
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
---
arch/arm/mach-omap2/twl-common.c | 160 ---------------------------------------
arch/arm/mach-omap2/twl-common.h | 3 -
2 files changed, 163 deletions(-)
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index 06a7521..cf3d81b 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -39,20 +39,6 @@ static struct i2c_board_info __initdata pmic_i2c_board_info = {
.flags = I2C_CLIENT_WAKE,
};
-#if defined(CONFIG_ARCH_OMAP3)
-static int twl_set_voltage(void *data, int target_uV)
-{
- struct voltagedomain *voltdm = (struct voltagedomain *)data;
- return voltdm_scale(voltdm, target_uV);
-}
-
-static int twl_get_voltage(void *data)
-{
- struct voltagedomain *voltdm = (struct voltagedomain *)data;
- return voltdm_get_voltage(voltdm);
-}
-#endif
-
void __init omap_pmic_init(int bus, u32 clkrate,
const char *pmic_type, int pmic_irq,
struct twl4030_platform_data *pmic_data)
@@ -76,152 +62,6 @@ void __init omap_pmic_late_init(void)
omap4_twl_init();
}
-#if defined(CONFIG_ARCH_OMAP3)
-static struct twl4030_usb_data omap3_usb_pdata = {
- .usb_mode = T2_USB_MODE_ULPI,
-};
-
-static int omap3_batt_table[] = {
-/* 0 C */
-30800, 29500, 28300, 27100,
-26000, 24900, 23900, 22900, 22000, 21100, 20300, 19400, 18700, 17900,
-17200, 16500, 15900, 15300, 14700, 14100, 13600, 13100, 12600, 12100,
-11600, 11200, 10800, 10400, 10000, 9630, 9280, 8950, 8620, 8310,
-8020, 7730, 7460, 7200, 6950, 6710, 6470, 6250, 6040, 5830,
-5640, 5450, 5260, 5090, 4920, 4760, 4600, 4450, 4310, 4170,
-4040, 3910, 3790, 3670, 3550
-};
-
-static struct twl4030_bci_platform_data omap3_bci_pdata = {
- .battery_tmp_tbl = omap3_batt_table,
- .tblsize = ARRAY_SIZE(omap3_batt_table),
-};
-
-static struct twl4030_madc_platform_data omap3_madc_pdata = {
- .irq_line = 1,
-};
-
-static struct twl4030_codec_data omap3_codec;
-
-static struct twl4030_audio_data omap3_audio_pdata = {
- .audio_mclk = 26000000,
- .codec = &omap3_codec,
-};
-
-static struct regulator_consumer_supply omap3_vdda_dac_supplies[] = {
- REGULATOR_SUPPLY("vdda_dac", "omapdss_venc"),
-};
-
-static struct regulator_init_data omap3_vdac_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3_vdda_dac_supplies),
- .consumer_supplies = omap3_vdda_dac_supplies,
-};
-
-static struct regulator_consumer_supply omap3_vpll2_supplies[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
-};
-
-static struct regulator_init_data omap3_vpll2_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3_vpll2_supplies),
- .consumer_supplies = omap3_vpll2_supplies,
-};
-
-static struct regulator_consumer_supply omap3_vdd1_supply[] = {
- REGULATOR_SUPPLY("vcc", "cpu0"),
-};
-
-static struct regulator_consumer_supply omap3_vdd2_supply[] = {
- REGULATOR_SUPPLY("vcc", "l3_main.0"),
-};
-
-static struct regulator_init_data omap3_vdd1 = {
- .constraints = {
- .name = "vdd_mpu_iva",
- .min_uV = 600000,
- .max_uV = 1450000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3_vdd1_supply),
- .consumer_supplies = omap3_vdd1_supply,
-};
-
-static struct regulator_init_data omap3_vdd2 = {
- .constraints = {
- .name = "vdd_core",
- .min_uV = 600000,
- .max_uV = 1450000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap3_vdd2_supply),
- .consumer_supplies = omap3_vdd2_supply,
-};
-
-static struct twl_regulator_driver_data omap3_vdd1_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap3_vdd2_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags)
-{
- if (!pmic_data->vdd1) {
- omap3_vdd1.driver_data = &omap3_vdd1_drvdata;
- omap3_vdd1_drvdata.data = voltdm_lookup("mpu_iva");
- pmic_data->vdd1 = &omap3_vdd1;
- }
- if (!pmic_data->vdd2) {
- omap3_vdd2.driver_data = &omap3_vdd2_drvdata;
- omap3_vdd2_drvdata.data = voltdm_lookup("core");
- pmic_data->vdd2 = &omap3_vdd2;
- }
-
- /* Common platform data configurations */
- if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
- pmic_data->usb = &omap3_usb_pdata;
-
- if (pdata_flags & TWL_COMMON_PDATA_BCI && !pmic_data->bci)
- pmic_data->bci = &omap3_bci_pdata;
-
- if (pdata_flags & TWL_COMMON_PDATA_MADC && !pmic_data->madc)
- pmic_data->madc = &omap3_madc_pdata;
-
- if (pdata_flags & TWL_COMMON_PDATA_AUDIO && !pmic_data->audio)
- pmic_data->audio = &omap3_audio_pdata;
-
- /* Common regulator configurations */
- if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac)
- pmic_data->vdac = &omap3_vdac_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VPLL2 && !pmic_data->vpll2)
- pmic_data->vpll2 = &omap3_vpll2_idata;
-}
-#endif /* CONFIG_ARCH_OMAP3 */
-
#if IS_ENABLED(CONFIG_SND_OMAP_SOC_OMAP_TWL4030)
#include <linux/platform_data/omap-twl4030.h>
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index 8e46ca3..048f6b2 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -51,9 +51,6 @@ static inline void omap3_pmic_init(const char *pmic_type,
omap_pmic_init(1, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
}
-void omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags);
-
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
#endif /* __OMAP_PMIC_COMMON__ */
--
2.5.5
^ permalink raw reply related
* [PATCH 1/5] ARM: OMAP4: kill omap4_pmic_init and omap4_pmic_get_config
From: Nicolae Rosia @ 2016-11-01 11:36 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478000206-10855-1-git-send-email-Nicolae_Rosia@mentor.com>
Remove dead code
Signed-off-by: Nicolae Rosia <Nicolae_Rosia@mentor.com>
---
arch/arm/mach-omap2/twl-common.c | 312 +--------------------------------------
arch/arm/mach-omap2/twl-common.h | 7 -
2 files changed, 1 insertion(+), 318 deletions(-)
diff --git a/arch/arm/mach-omap2/twl-common.c b/arch/arm/mach-omap2/twl-common.c
index a72738e..06a7521 100644
--- a/arch/arm/mach-omap2/twl-common.c
+++ b/arch/arm/mach-omap2/twl-common.c
@@ -39,7 +39,7 @@ static struct i2c_board_info __initdata pmic_i2c_board_info = {
.flags = I2C_CLIENT_WAKE,
};
-#if defined(CONFIG_ARCH_OMAP3) || defined(CONFIG_ARCH_OMAP4)
+#if defined(CONFIG_ARCH_OMAP3)
static int twl_set_voltage(void *data, int target_uV)
{
struct voltagedomain *voltdm = (struct voltagedomain *)data;
@@ -66,25 +66,6 @@ void __init omap_pmic_init(int bus, u32 clkrate,
omap_register_i2c_bus(bus, clkrate, &pmic_i2c_board_info, 1);
}
-#ifdef CONFIG_ARCH_OMAP4
-void __init omap4_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data,
- struct i2c_board_info *devices, int nr_devices)
-{
- /* PMIC part*/
- unsigned int irq;
-
- omap_mux_init_signal("sys_nirq1", OMAP_PIN_INPUT_PULLUP | OMAP_PIN_OFF_WAKEUPENABLE);
- omap_mux_init_signal("fref_clk0_out.sys_drm_msecure", OMAP_PIN_OUTPUT);
- irq = omap4_xlate_irq(7 + OMAP44XX_IRQ_GIC_START);
- omap_pmic_init(1, 400, pmic_type, irq, pmic_data);
-
- /* Register additional devices on i2c1 bus if needed */
- if (devices)
- i2c_register_board_info(1, devices, nr_devices);
-}
-#endif
-
void __init omap_pmic_late_init(void)
{
/* Init the OMAP TWL parameters (if PMIC has been registerd) */
@@ -241,297 +222,6 @@ void __init omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
}
#endif /* CONFIG_ARCH_OMAP3 */
-#if defined(CONFIG_ARCH_OMAP4)
-static struct twl4030_usb_data omap4_usb_pdata = {
-};
-
-static struct regulator_consumer_supply omap4_vdda_hdmi_dac_supplies[] = {
- REGULATOR_SUPPLY("vdda_hdmi_dac", "omapdss_hdmi"),
-};
-
-static struct regulator_init_data omap4_vdac_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdda_hdmi_dac_supplies),
- .consumer_supplies = omap4_vdda_hdmi_dac_supplies,
- .supply_regulator = "V2V1",
-};
-
-static struct regulator_init_data omap4_vaux2_idata = {
- .constraints = {
- .min_uV = 1200000,
- .max_uV = 2800000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_vaux3_idata = {
- .constraints = {
- .min_uV = 1000000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vmmc_supply[] = {
- REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
-};
-
-/* VMMC1 for MMC1 card */
-static struct regulator_init_data omap4_vmmc_idata = {
- .constraints = {
- .min_uV = 1200000,
- .max_uV = 3000000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vmmc_supply),
- .consumer_supplies = omap4_vmmc_supply,
-};
-
-static struct regulator_init_data omap4_vpp_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 2500000,
- .apply_uV = true,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
- | REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_vana_idata = {
- .constraints = {
- .min_uV = 2100000,
- .max_uV = 2100000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vcxio_supply[] = {
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dss"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
- REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.1"),
-};
-
-static struct regulator_init_data omap4_vcxio_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- .always_on = true,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vcxio_supply),
- .consumer_supplies = omap4_vcxio_supply,
- .supply_regulator = "V2V1",
-};
-
-static struct regulator_init_data omap4_vusb_idata = {
- .constraints = {
- .min_uV = 3300000,
- .max_uV = 3300000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_init_data omap4_clk32kg_idata = {
- .constraints = {
- .valid_ops_mask = REGULATOR_CHANGE_STATUS,
- },
-};
-
-static struct regulator_consumer_supply omap4_vdd1_supply[] = {
- REGULATOR_SUPPLY("vcc", "cpu0"),
-};
-
-static struct regulator_consumer_supply omap4_vdd2_supply[] = {
- REGULATOR_SUPPLY("vcc", "iva.0"),
-};
-
-static struct regulator_consumer_supply omap4_vdd3_supply[] = {
- REGULATOR_SUPPLY("vcc", "l3_main.0"),
-};
-
-static struct regulator_init_data omap4_vdd1 = {
- .constraints = {
- .name = "vdd_mpu",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd1_supply),
- .consumer_supplies = omap4_vdd1_supply,
-};
-
-static struct regulator_init_data omap4_vdd2 = {
- .constraints = {
- .name = "vdd_iva",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd2_supply),
- .consumer_supplies = omap4_vdd2_supply,
-};
-
-static struct regulator_init_data omap4_vdd3 = {
- .constraints = {
- .name = "vdd_core",
- .min_uV = 500000,
- .max_uV = 1500000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL,
- .valid_ops_mask = REGULATOR_CHANGE_VOLTAGE,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_vdd3_supply),
- .consumer_supplies = omap4_vdd3_supply,
-};
-
-
-static struct twl_regulator_driver_data omap4_vdd1_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap4_vdd2_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct twl_regulator_driver_data omap4_vdd3_drvdata = {
- .get_voltage = twl_get_voltage,
- .set_voltage = twl_set_voltage,
-};
-
-static struct regulator_consumer_supply omap4_v1v8_supply[] = {
- REGULATOR_SUPPLY("vio", "1-004b"),
-};
-
-static struct regulator_init_data omap4_v1v8_idata = {
- .constraints = {
- .min_uV = 1800000,
- .max_uV = 1800000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- .always_on = true,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_v1v8_supply),
- .consumer_supplies = omap4_v1v8_supply,
-};
-
-static struct regulator_consumer_supply omap4_v2v1_supply[] = {
- REGULATOR_SUPPLY("v2v1", "1-004b"),
-};
-
-static struct regulator_init_data omap4_v2v1_idata = {
- .constraints = {
- .min_uV = 2100000,
- .max_uV = 2100000,
- .valid_modes_mask = REGULATOR_MODE_NORMAL
- | REGULATOR_MODE_STANDBY,
- .valid_ops_mask = REGULATOR_CHANGE_MODE
- | REGULATOR_CHANGE_STATUS,
- },
- .num_consumer_supplies = ARRAY_SIZE(omap4_v2v1_supply),
- .consumer_supplies = omap4_v2v1_supply,
-};
-
-void __init omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags)
-{
- if (!pmic_data->vdd1) {
- omap4_vdd1.driver_data = &omap4_vdd1_drvdata;
- omap4_vdd1_drvdata.data = voltdm_lookup("mpu");
- pmic_data->vdd1 = &omap4_vdd1;
- }
-
- if (!pmic_data->vdd2) {
- omap4_vdd2.driver_data = &omap4_vdd2_drvdata;
- omap4_vdd2_drvdata.data = voltdm_lookup("iva");
- pmic_data->vdd2 = &omap4_vdd2;
- }
-
- if (!pmic_data->vdd3) {
- omap4_vdd3.driver_data = &omap4_vdd3_drvdata;
- omap4_vdd3_drvdata.data = voltdm_lookup("core");
- pmic_data->vdd3 = &omap4_vdd3;
- }
-
- /* Common platform data configurations */
- if (pdata_flags & TWL_COMMON_PDATA_USB && !pmic_data->usb)
- pmic_data->usb = &omap4_usb_pdata;
-
- /* Common regulator configurations */
- if (regulators_flags & TWL_COMMON_REGULATOR_VDAC && !pmic_data->vdac)
- pmic_data->vdac = &omap4_vdac_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VAUX2 && !pmic_data->vaux2)
- pmic_data->vaux2 = &omap4_vaux2_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VAUX3 && !pmic_data->vaux3)
- pmic_data->vaux3 = &omap4_vaux3_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VMMC && !pmic_data->vmmc)
- pmic_data->vmmc = &omap4_vmmc_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VPP && !pmic_data->vpp)
- pmic_data->vpp = &omap4_vpp_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VANA && !pmic_data->vana)
- pmic_data->vana = &omap4_vana_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VCXIO && !pmic_data->vcxio)
- pmic_data->vcxio = &omap4_vcxio_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_VUSB && !pmic_data->vusb)
- pmic_data->vusb = &omap4_vusb_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_CLK32KG &&
- !pmic_data->clk32kg)
- pmic_data->clk32kg = &omap4_clk32kg_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_V1V8 && !pmic_data->v1v8)
- pmic_data->v1v8 = &omap4_v1v8_idata;
-
- if (regulators_flags & TWL_COMMON_REGULATOR_V2V1 && !pmic_data->v2v1)
- pmic_data->v2v1 = &omap4_v2v1_idata;
-}
-#endif /* CONFIG_ARCH_OMAP4 */
-
#if IS_ENABLED(CONFIG_SND_OMAP_SOC_OMAP_TWL4030)
#include <linux/platform_data/omap-twl4030.h>
diff --git a/arch/arm/mach-omap2/twl-common.h b/arch/arm/mach-omap2/twl-common.h
index 24b65d0..8e46ca3 100644
--- a/arch/arm/mach-omap2/twl-common.h
+++ b/arch/arm/mach-omap2/twl-common.h
@@ -51,16 +51,9 @@ static inline void omap3_pmic_init(const char *pmic_type,
omap_pmic_init(1, 2600, pmic_type, 7 + OMAP_INTC_START, pmic_data);
}
-void omap4_pmic_init(const char *pmic_type,
- struct twl4030_platform_data *pmic_data,
- struct i2c_board_info *devices, int nr_devices);
-
void omap3_pmic_get_config(struct twl4030_platform_data *pmic_data,
u32 pdata_flags, u32 regulators_flags);
-void omap4_pmic_get_config(struct twl4030_platform_data *pmic_data,
- u32 pdata_flags, u32 regulators_flags);
-
void omap_twl4030_audio_init(char *card_name, struct omap_tw4030_pdata *pdata);
#endif /* __OMAP_PMIC_COMMON__ */
--
2.5.5
^ permalink raw reply related
* [PATCH 0/5] ARM: OMAP: dead code removal
From: Nicolae Rosia @ 2016-11-01 11:36 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
I have identified some dead code which can be removed.
Nicolae Rosia (5):
ARM: OMAP4: kill omap4_pmic_init and omap4_pmic_get_config
ARM: OMAP3: kill omap3_pmic_get_config and twl_{get,set}_voltage
ARM: OMAP3: kill omap3_pmic_init
ARM: OMAP2: kill omap2_pmic_init
ARM: OMAP: kill omap_pmic_init
arch/arm/mach-omap2/twl-common.c | 483 ---------------------------------------
arch/arm/mach-omap2/twl-common.h | 24 --
2 files changed, 507 deletions(-)
--
2.5.5
^ permalink raw reply
* [PATCH v3] ARM: dts: Add gyro and accel to APQ8060 Dragonboard
From: Linus Walleij @ 2016-11-01 11:31 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161031222029.GG25787@tuxbot>
On Mon, Oct 31, 2016 at 11:20 PM, Bjorn Andersson
<bjorn.andersson@linaro.org> wrote:
>> + interrupt-parent = <&pm8058_gpio>;
>> + interrupts = <208 IRQ_TYPE_EDGE_FALLING>;
>
> To remove the need of resetting the interrupt-parent in each child you
> can use the following form:
>
> interrupts-extended = <&pm8058_gpio 208 IRQ_TYPE_EDGE_FALLING>;
>
> But, if we correct the ssbi gpio driver then this would no longer be
> interrupt 208 in this parent, right?. I believe that if you say
> <&pmicintc 208 IRQ_TYPE_EDGE_FALLING> instead, which should work even
> after we correct the gpio translation.
Yes. It should be fixed everywhere but is not related to this
patch. But I can do a two-patch series first fixing this and then
adding the gyro+accelerometer on top referencing the MFD
pmicintc as parent.
> (Which probably means we need to get that redesigned, before we
> introduce to many of these)
What needs to happen is for the SSBI and SPMI GPIO to use a
hierarchical irqdomain so their GPIO local line offset and hwirq
are the same. Then we can reference the GPIO IRQ lines directly
in a correct manner.
You are not alone with this mess. A lot of hierarchical GPIOs
are wrong. My fail as GPIO maintainer I guess, ouch.
Yours,
Linus Walleij
^ permalink raw reply
* [PATCH v16 5/5] CMDQ: save energy
From: HS Liao @ 2016-11-01 11:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477999698-6288-1-git-send-email-hs.liao@mediatek.com>
use clk_disable_unprepare instead of clk_disable to save more energy
when CMDQ is idle.
Signed-off-by: HS Liao <hs.liao@mediatek.com>
---
drivers/mailbox/mtk-cmdq-mailbox.c | 52 ++++++++++++++++++++++++++++++++------
1 file changed, 44 insertions(+), 8 deletions(-)
diff --git a/drivers/mailbox/mtk-cmdq-mailbox.c b/drivers/mailbox/mtk-cmdq-mailbox.c
index 747bcd3..8771e57 100644
--- a/drivers/mailbox/mtk-cmdq-mailbox.c
+++ b/drivers/mailbox/mtk-cmdq-mailbox.c
@@ -22,6 +22,7 @@
#include <linux/mailbox_controller.h>
#include <linux/mailbox/mtk-cmdq-mailbox.h>
#include <linux/timer.h>
+#include <linux/workqueue.h>
#define CMDQ_THR_MAX_COUNT 3 /* main, sub, general(misc) */
#define CMDQ_OP_CODE_MASK (0xff << CMDQ_OP_CODE_SHIFT)
@@ -75,10 +76,16 @@ struct cmdq_task {
struct cmdq_pkt *pkt; /* the packet sent from mailbox client */
};
+struct cmdq_clk_release {
+ struct cmdq *cmdq;
+ struct work_struct release_work;
+};
+
struct cmdq {
struct mbox_controller mbox;
void __iomem *base;
u32 irq;
+ struct workqueue_struct *clk_release_wq;
struct cmdq_thread thread[CMDQ_THR_MAX_COUNT];
struct clk *clock;
bool suspended;
@@ -203,7 +210,7 @@ static void cmdq_task_exec(struct cmdq_pkt *pkt, struct cmdq_thread *thread)
{
struct cmdq *cmdq;
struct cmdq_task *task;
- unsigned long curr_pa, end_pa;
+ unsigned long curr_pa, end_pa, flags;
cmdq = dev_get_drvdata(thread->chan->mbox->dev);
@@ -219,7 +226,14 @@ static void cmdq_task_exec(struct cmdq_pkt *pkt, struct cmdq_thread *thread)
task->pkt = pkt;
if (list_empty(&thread->task_busy_list)) {
- WARN_ON(clk_enable(cmdq->clock) < 0);
+ /*
+ * Unlock for clk prepare (sleeping function).
+ * This is safe since clk_prepare_enable has internal locks.
+ */
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+ WARN_ON(clk_prepare_enable(cmdq->clock) < 0);
+ spin_lock_irqsave(&thread->chan->lock, flags);
+
WARN_ON(cmdq_thread_reset(cmdq, thread) < 0);
writel(task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
@@ -301,6 +315,26 @@ static void cmdq_task_handle_error(struct cmdq_task *task)
cmdq_thread_resume(thread);
}
+static void cmdq_clk_release_work(struct work_struct *work_item)
+{
+ struct cmdq_clk_release *clk_release = container_of(work_item,
+ struct cmdq_clk_release, release_work);
+ struct cmdq *cmdq = clk_release->cmdq;
+
+ clk_disable_unprepare(cmdq->clock);
+ kfree(clk_release);
+}
+
+static void cmdq_clk_release_schedule(struct cmdq *cmdq)
+{
+ struct cmdq_clk_release *clk_release;
+
+ clk_release = kmalloc(sizeof(*clk_release), GFP_ATOMIC);
+ clk_release->cmdq = cmdq;
+ INIT_WORK(&clk_release->release_work, cmdq_clk_release_work);
+ queue_work(cmdq->clk_release_wq, &clk_release->release_work);
+}
+
static void cmdq_thread_irq_handler(struct cmdq *cmdq,
struct cmdq_thread *thread)
{
@@ -350,7 +384,7 @@ static void cmdq_thread_irq_handler(struct cmdq *cmdq,
if (list_empty(&thread->task_busy_list)) {
cmdq_thread_disable(cmdq, thread);
- clk_disable(cmdq->clock);
+ cmdq_clk_release_schedule(cmdq);
} else {
mod_timer(&thread->timeout,
jiffies + msecs_to_jiffies(CMDQ_TIMEOUT_MS));
@@ -409,7 +443,7 @@ static void cmdq_thread_handle_timeout(unsigned long data)
cmdq_thread_resume(thread);
cmdq_thread_disable(cmdq, thread);
- clk_disable(cmdq->clock);
+ cmdq_clk_release_schedule(cmdq);
spin_unlock_irqrestore(&thread->chan->lock, flags);
}
@@ -433,7 +467,7 @@ static int cmdq_suspend(struct device *dev)
if (task_running)
dev_warn(dev, "exist running task(s) in suspend\n");
- clk_unprepare(cmdq->clock);
+ flush_workqueue(cmdq->clk_release_wq);
return 0;
}
@@ -441,7 +475,6 @@ static int cmdq_resume(struct device *dev)
{
struct cmdq *cmdq = dev_get_drvdata(dev);
- WARN_ON(clk_prepare(cmdq->clock) < 0);
cmdq->suspended = false;
return 0;
}
@@ -450,8 +483,8 @@ static int cmdq_remove(struct platform_device *pdev)
{
struct cmdq *cmdq = platform_get_drvdata(pdev);
+ destroy_workqueue(cmdq->clk_release_wq);
mbox_controller_unregister(&cmdq->mbox);
- clk_unprepare(cmdq->clock);
return 0;
}
@@ -567,8 +600,11 @@ static int cmdq_probe(struct platform_device *pdev)
return err;
}
+ cmdq->clk_release_wq = alloc_ordered_workqueue(
+ "%s", WQ_MEM_RECLAIM | WQ_HIGHPRI,
+ "cmdq_clk_release");
+
platform_set_drvdata(pdev, cmdq);
- WARN_ON(clk_prepare(cmdq->clock) < 0);
return 0;
}
--
1.9.1
^ permalink raw reply related
* [PATCH v16 4/5] CMDQ: suspend and resume
From: HS Liao @ 2016-11-01 11:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477999698-6288-1-git-send-email-hs.liao@mediatek.com>
take suspend and resume into consideration
Signed-off-by: HS Liao <hs.liao@mediatek.com>
---
drivers/mailbox/mtk-cmdq-mailbox.c | 44 ++++++++++++++++++++++++++++++++++++++
1 file changed, 44 insertions(+)
diff --git a/drivers/mailbox/mtk-cmdq-mailbox.c b/drivers/mailbox/mtk-cmdq-mailbox.c
index d086fd8..747bcd3 100644
--- a/drivers/mailbox/mtk-cmdq-mailbox.c
+++ b/drivers/mailbox/mtk-cmdq-mailbox.c
@@ -81,6 +81,7 @@ struct cmdq {
u32 irq;
struct cmdq_thread thread[CMDQ_THR_MAX_COUNT];
struct clk *clock;
+ bool suspended;
};
static int cmdq_thread_suspend(struct cmdq *cmdq, struct cmdq_thread *thread)
@@ -206,6 +207,9 @@ static void cmdq_task_exec(struct cmdq_pkt *pkt, struct cmdq_thread *thread)
cmdq = dev_get_drvdata(thread->chan->mbox->dev);
+ /* Client should not flush new tasks if suspended. */
+ WARN_ON(cmdq->suspended);
+
task = kzalloc(sizeof(*task), GFP_ATOMIC);
task->cmdq = cmdq;
INIT_LIST_HEAD(&task->list_entry);
@@ -409,6 +413,39 @@ static void cmdq_thread_handle_timeout(unsigned long data)
spin_unlock_irqrestore(&thread->chan->lock, flags);
}
+static int cmdq_suspend(struct device *dev)
+{
+ struct cmdq *cmdq = dev_get_drvdata(dev);
+ struct cmdq_thread *thread;
+ int i;
+ bool task_running = false;
+
+ cmdq->suspended = true;
+
+ for (i = 0; i < ARRAY_SIZE(cmdq->thread); i++) {
+ thread = &cmdq->thread[i];
+ if (!list_empty(&thread->task_busy_list)) {
+ task_running = true;
+ break;
+ }
+ }
+
+ if (task_running)
+ dev_warn(dev, "exist running task(s) in suspend\n");
+
+ clk_unprepare(cmdq->clock);
+ return 0;
+}
+
+static int cmdq_resume(struct device *dev)
+{
+ struct cmdq *cmdq = dev_get_drvdata(dev);
+
+ WARN_ON(clk_prepare(cmdq->clock) < 0);
+ cmdq->suspended = false;
+ return 0;
+}
+
static int cmdq_remove(struct platform_device *pdev)
{
struct cmdq *cmdq = platform_get_drvdata(pdev);
@@ -532,9 +569,15 @@ static int cmdq_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, cmdq);
WARN_ON(clk_prepare(cmdq->clock) < 0);
+
return 0;
}
+static const struct dev_pm_ops cmdq_pm_ops = {
+ .suspend = cmdq_suspend,
+ .resume = cmdq_resume,
+};
+
static const struct of_device_id cmdq_of_ids[] = {
{.compatible = "mediatek,mt8173-gce",},
{}
@@ -545,6 +588,7 @@ static int cmdq_probe(struct platform_device *pdev)
.remove = cmdq_remove,
.driver = {
.name = "mtk_cmdq",
+ .pm = &cmdq_pm_ops,
.of_match_table = cmdq_of_ids,
}
};
--
1.9.1
^ permalink raw reply related
* [PATCH v16 3/5] arm64: dts: mt8173: Add GCE node
From: HS Liao @ 2016-11-01 11:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477999698-6288-1-git-send-email-hs.liao@mediatek.com>
This patch adds the device node of the GCE hardware for CMDQ module.
Signed-off-by: HS Liao <hs.liao@mediatek.com>
---
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm64/boot/dts/mediatek/mt8173.dtsi b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
index 1c71e25..d50c044 100644
--- a/arch/arm64/boot/dts/mediatek/mt8173.dtsi
+++ b/arch/arm64/boot/dts/mediatek/mt8173.dtsi
@@ -414,6 +414,16 @@
status = "disabled";
};
+ gce: gce at 10212000 {
+ compatible = "mediatek,mt8173-gce";
+ reg = <0 0x10212000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_GCE>;
+ clock-names = "gce";
+
+ #mbox-cells = <2>;
+ };
+
mipi_tx0: mipi-dphy at 10215000 {
compatible = "mediatek,mt8173-mipi-tx";
reg = <0 0x10215000 0 0x1000>;
--
1.9.1
^ permalink raw reply related
* [PATCH v16 2/5] CMDQ: Mediatek CMDQ driver
From: HS Liao @ 2016-11-01 11:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477999698-6288-1-git-send-email-hs.liao@mediatek.com>
This patch is first version of Mediatek Command Queue(CMDQ) driver. The
CMDQ is used to help write registers with critical time limitation,
such as updating display configuration during the vblank. It controls
Global Command Engine (GCE) hardware to achieve this requirement.
Currently, CMDQ only supports display related hardwares, but we expect
it can be extended to other hardwares for future requirements.
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Signed-off-by: CK Hu <ck.hu@mediatek.com>
---
drivers/mailbox/Kconfig | 10 +
drivers/mailbox/Makefile | 2 +
drivers/mailbox/mtk-cmdq-mailbox.c | 552 +++++++++++++++++++++++++++++++
drivers/soc/mediatek/Kconfig | 11 +
drivers/soc/mediatek/Makefile | 1 +
drivers/soc/mediatek/mtk-cmdq-helper.c | 310 +++++++++++++++++
include/linux/mailbox/mtk-cmdq-mailbox.h | 67 ++++
include/linux/soc/mediatek/mtk-cmdq.h | 182 ++++++++++
8 files changed, 1135 insertions(+)
create mode 100644 drivers/mailbox/mtk-cmdq-mailbox.c
create mode 100644 drivers/soc/mediatek/mtk-cmdq-helper.c
create mode 100644 include/linux/mailbox/mtk-cmdq-mailbox.h
create mode 100644 include/linux/soc/mediatek/mtk-cmdq.h
diff --git a/drivers/mailbox/Kconfig b/drivers/mailbox/Kconfig
index 11eebfe..5a4af2d 100644
--- a/drivers/mailbox/Kconfig
+++ b/drivers/mailbox/Kconfig
@@ -143,4 +143,14 @@ config BCM_PDC_MBOX
Mailbox implementation for the Broadcom PDC ring manager,
which provides access to various offload engines on Broadcom
SoCs. Say Y here if you want to use the Broadcom PDC.
+
+config MTK_CMDQ_MBOX
+ bool "MediaTek CMDQ Mailbox Support"
+ depends on ARM64 && ( ARCH_MEDIATEK || COMPILE_TEST )
+ select MTK_INFRACFG
+ help
+ Say yes here to add support for the MediaTek Command Queue (CMDQ)
+ mailbox driver. The CMDQ is used to help read/write registers with
+ critical time limitation, such as updating display configuration
+ during the vblank.
endif
diff --git a/drivers/mailbox/Makefile b/drivers/mailbox/Makefile
index ace6fed..b904bed 100644
--- a/drivers/mailbox/Makefile
+++ b/drivers/mailbox/Makefile
@@ -29,3 +29,5 @@ obj-$(CONFIG_XGENE_SLIMPRO_MBOX) += mailbox-xgene-slimpro.o
obj-$(CONFIG_HI6220_MBOX) += hi6220-mailbox.o
obj-$(CONFIG_BCM_PDC_MBOX) += bcm-pdc-mailbox.o
+
+obj-$(CONFIG_MTK_CMDQ_MBOX) += mtk-cmdq-mailbox.o
diff --git a/drivers/mailbox/mtk-cmdq-mailbox.c b/drivers/mailbox/mtk-cmdq-mailbox.c
new file mode 100644
index 0000000..d086fd8
--- /dev/null
+++ b/drivers/mailbox/mtk-cmdq-mailbox.c
@@ -0,0 +1,552 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/clk-provider.h>
+#include <linux/dma-mapping.h>
+#include <linux/errno.h>
+#include <linux/interrupt.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/mailbox_controller.h>
+#include <linux/mailbox/mtk-cmdq-mailbox.h>
+#include <linux/timer.h>
+
+#define CMDQ_THR_MAX_COUNT 3 /* main, sub, general(misc) */
+#define CMDQ_OP_CODE_MASK (0xff << CMDQ_OP_CODE_SHIFT)
+#define CMDQ_TIMEOUT_MS 1000
+#define CMDQ_IRQ_MASK 0xffff
+#define CMDQ_NUM_CMD(t) (t->cmd_buf_size / CMDQ_INST_SIZE)
+
+#define CMDQ_CURR_IRQ_STATUS 0x10
+#define CMDQ_THR_SLOT_CYCLES 0x30
+
+#define CMDQ_THR_BASE 0x100
+#define CMDQ_THR_SIZE 0x80
+#define CMDQ_THR_WARM_RESET 0x00
+#define CMDQ_THR_ENABLE_TASK 0x04
+#define CMDQ_THR_SUSPEND_TASK 0x08
+#define CMDQ_THR_CURR_STATUS 0x0c
+#define CMDQ_THR_IRQ_STATUS 0x10
+#define CMDQ_THR_IRQ_ENABLE 0x14
+#define CMDQ_THR_CURR_ADDR 0x20
+#define CMDQ_THR_END_ADDR 0x24
+#define CMDQ_THR_WAIT_TOKEN 0x30
+
+#define CMDQ_THR_ENABLED 0x1
+#define CMDQ_THR_DISABLED 0x0
+#define CMDQ_THR_SUSPEND 0x1
+#define CMDQ_THR_RESUME 0x0
+#define CMDQ_THR_STATUS_SUSPENDED BIT(1)
+#define CMDQ_THR_DO_WARM_RESET BIT(0)
+#define CMDQ_THR_ACTIVE_SLOT_CYCLES 0x3200
+#define CMDQ_THR_IRQ_DONE 0x1
+#define CMDQ_THR_IRQ_ERROR 0x12
+#define CMDQ_THR_IRQ_EN (CMDQ_THR_IRQ_ERROR | CMDQ_THR_IRQ_DONE)
+#define CMDQ_THR_IS_WAITING BIT(31)
+
+#define CMDQ_JUMP_BY_OFFSET 0x10000000
+#define CMDQ_JUMP_BY_PA 0x10000001
+
+struct cmdq_thread {
+ struct mbox_chan *chan;
+ void __iomem *base;
+ struct list_head task_busy_list;
+ struct timer_list timeout;
+ bool atomic_exec;
+};
+
+struct cmdq_task {
+ struct cmdq *cmdq;
+ struct list_head list_entry;
+ dma_addr_t pa_base;
+ struct cmdq_thread *thread;
+ struct cmdq_pkt *pkt; /* the packet sent from mailbox client */
+};
+
+struct cmdq {
+ struct mbox_controller mbox;
+ void __iomem *base;
+ u32 irq;
+ struct cmdq_thread thread[CMDQ_THR_MAX_COUNT];
+ struct clk *clock;
+};
+
+static int cmdq_thread_suspend(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+ u32 status;
+
+ writel(CMDQ_THR_SUSPEND, thread->base + CMDQ_THR_SUSPEND_TASK);
+
+ /* If already disabled, treat as suspended successful. */
+ if (!(readl(thread->base + CMDQ_THR_ENABLE_TASK) & CMDQ_THR_ENABLED))
+ return 0;
+
+ if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_CURR_STATUS,
+ status, status & CMDQ_THR_STATUS_SUSPENDED, 0, 10)) {
+ dev_err(cmdq->mbox.dev, "suspend GCE thread 0x%x failed\n",
+ (u32)(thread->base - cmdq->base));
+ return -EFAULT;
+ }
+
+ return 0;
+}
+
+static void cmdq_thread_resume(struct cmdq_thread *thread)
+{
+ writel(CMDQ_THR_RESUME, thread->base + CMDQ_THR_SUSPEND_TASK);
+}
+
+static int cmdq_thread_reset(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+ u32 warm_reset;
+
+ writel(CMDQ_THR_DO_WARM_RESET, thread->base + CMDQ_THR_WARM_RESET);
+ if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_WARM_RESET,
+ warm_reset, !(warm_reset & CMDQ_THR_DO_WARM_RESET),
+ 0, 10)) {
+ dev_err(cmdq->mbox.dev, "reset GCE thread 0x%x failed\n",
+ (u32)(thread->base - cmdq->base));
+ return -EFAULT;
+ }
+ writel(CMDQ_THR_ACTIVE_SLOT_CYCLES, cmdq->base + CMDQ_THR_SLOT_CYCLES);
+ return 0;
+}
+
+static void cmdq_thread_disable(struct cmdq *cmdq, struct cmdq_thread *thread)
+{
+ cmdq_thread_reset(cmdq, thread);
+ writel(CMDQ_THR_DISABLED, thread->base + CMDQ_THR_ENABLE_TASK);
+}
+
+/* notify GCE to re-fetch commands by setting GCE thread PC */
+static void cmdq_thread_invalidate_fetched_data(struct cmdq_thread *thread)
+{
+ writel(readl(thread->base + CMDQ_THR_CURR_ADDR),
+ thread->base + CMDQ_THR_CURR_ADDR);
+}
+
+static void cmdq_task_insert_into_thread(struct cmdq_task *task)
+{
+ struct device *dev = task->cmdq->mbox.dev;
+ struct cmdq_thread *thread = task->thread;
+ struct cmdq_task *prev_task = list_last_entry(
+ &thread->task_busy_list, typeof(*task), list_entry);
+ u64 *prev_task_base = prev_task->pkt->va_base;
+
+ /* let previous task jump to this task */
+ dma_sync_single_for_cpu(dev, prev_task->pa_base,
+ prev_task->pkt->cmd_buf_size, DMA_TO_DEVICE);
+ prev_task_base[CMDQ_NUM_CMD(prev_task->pkt) - 1] =
+ (u64)CMDQ_JUMP_BY_PA << 32 | task->pa_base;
+ dma_sync_single_for_device(dev, prev_task->pa_base,
+ prev_task->pkt->cmd_buf_size, DMA_TO_DEVICE);
+
+ cmdq_thread_invalidate_fetched_data(thread);
+}
+
+static bool cmdq_command_is_wfe(u64 cmd)
+{
+ u64 wfe_option = CMDQ_WFE_UPDATE | CMDQ_WFE_WAIT | CMDQ_WFE_WAIT_VALUE;
+ u64 wfe_op = (u64)(CMDQ_CODE_WFE << CMDQ_OP_CODE_SHIFT) << 32;
+ u64 wfe_mask = (u64)CMDQ_OP_CODE_MASK << 32 | 0xffffffff;
+
+ return ((cmd & wfe_mask) == (wfe_op | wfe_option));
+}
+
+/* we assume tasks in the same display GCE thread are waiting the same event. */
+static void cmdq_task_remove_wfe(struct cmdq_task *task)
+{
+ struct device *dev = task->cmdq->mbox.dev;
+ u64 *base = task->pkt->va_base;
+ int i;
+
+ dma_sync_single_for_cpu(dev, task->pa_base, task->pkt->cmd_buf_size,
+ DMA_TO_DEVICE);
+ for (i = 0; i < CMDQ_NUM_CMD(task->pkt); i++)
+ if (cmdq_command_is_wfe(base[i]))
+ base[i] = (u64)CMDQ_JUMP_BY_OFFSET << 32 |
+ CMDQ_JUMP_PASS;
+ dma_sync_single_for_device(dev, task->pa_base, task->pkt->cmd_buf_size,
+ DMA_TO_DEVICE);
+}
+
+static bool cmdq_thread_is_in_wfe(struct cmdq_thread *thread)
+{
+ return readl(thread->base + CMDQ_THR_WAIT_TOKEN) & CMDQ_THR_IS_WAITING;
+}
+
+static void cmdq_thread_wait_end(struct cmdq_thread *thread,
+ unsigned long end_pa)
+{
+ struct device *dev = thread->chan->mbox->dev;
+ unsigned long curr_pa;
+
+ if (readl_poll_timeout_atomic(thread->base + CMDQ_THR_CURR_ADDR,
+ curr_pa, curr_pa == end_pa, 1, 20))
+ dev_err(dev, "GCE thread cannot run to end.\n");
+}
+
+static void cmdq_task_exec(struct cmdq_pkt *pkt, struct cmdq_thread *thread)
+{
+ struct cmdq *cmdq;
+ struct cmdq_task *task;
+ unsigned long curr_pa, end_pa;
+
+ cmdq = dev_get_drvdata(thread->chan->mbox->dev);
+
+ task = kzalloc(sizeof(*task), GFP_ATOMIC);
+ task->cmdq = cmdq;
+ INIT_LIST_HEAD(&task->list_entry);
+ task->pa_base = dma_map_single(cmdq->mbox.dev, pkt->va_base,
+ pkt->cmd_buf_size, DMA_TO_DEVICE);
+ task->thread = thread;
+ task->pkt = pkt;
+
+ if (list_empty(&thread->task_busy_list)) {
+ WARN_ON(clk_enable(cmdq->clock) < 0);
+ WARN_ON(cmdq_thread_reset(cmdq, thread) < 0);
+
+ writel(task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
+ writel(task->pa_base + pkt->cmd_buf_size,
+ thread->base + CMDQ_THR_END_ADDR);
+ writel(CMDQ_THR_IRQ_EN, thread->base + CMDQ_THR_IRQ_ENABLE);
+ writel(CMDQ_THR_ENABLED, thread->base + CMDQ_THR_ENABLE_TASK);
+
+ mod_timer(&thread->timeout,
+ jiffies + msecs_to_jiffies(CMDQ_TIMEOUT_MS));
+ } else {
+ WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+ curr_pa = readl(thread->base + CMDQ_THR_CURR_ADDR);
+ end_pa = readl(thread->base + CMDQ_THR_END_ADDR);
+
+ /*
+ * Atomic execution should remove the following wfe, i.e. only
+ * wait event at first task, and prevent to pause when running.
+ */
+ if (thread->atomic_exec) {
+ /* GCE is executing if command is not WFE */
+ if (!cmdq_thread_is_in_wfe(thread)) {
+ cmdq_thread_resume(thread);
+ cmdq_thread_wait_end(thread, end_pa);
+ WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+ /* set to this task directly */
+ writel(task->pa_base,
+ thread->base + CMDQ_THR_CURR_ADDR);
+ } else {
+ cmdq_task_insert_into_thread(task);
+ cmdq_task_remove_wfe(task);
+ smp_mb(); /* modify jump before enable thread */
+ }
+ } else {
+ /* check boundary */
+ if (curr_pa == end_pa - CMDQ_INST_SIZE ||
+ curr_pa == end_pa) {
+ /* set to this task directly */
+ writel(task->pa_base,
+ thread->base + CMDQ_THR_CURR_ADDR);
+ } else {
+ cmdq_task_insert_into_thread(task);
+ smp_mb(); /* modify jump before enable thread */
+ }
+ }
+ writel(task->pa_base + pkt->cmd_buf_size,
+ thread->base + CMDQ_THR_END_ADDR);
+ cmdq_thread_resume(thread);
+ }
+ list_move_tail(&task->list_entry, &thread->task_busy_list);
+}
+
+static void cmdq_task_exec_done(struct cmdq_task *task, bool err)
+{
+ struct device *dev = task->cmdq->mbox.dev;
+ struct cmdq_cb_data cmdq_cb_data;
+
+ dma_unmap_single(dev, task->pa_base, task->pkt->cmd_buf_size,
+ DMA_TO_DEVICE);
+ if (task->pkt->cb.cb) {
+ cmdq_cb_data.err = err;
+ cmdq_cb_data.data = task->pkt->cb.data;
+ task->pkt->cb.cb(cmdq_cb_data);
+ }
+ list_del(&task->list_entry);
+}
+
+static void cmdq_task_handle_error(struct cmdq_task *task)
+{
+ struct cmdq_thread *thread = task->thread;
+ struct cmdq_task *next_task;
+
+ dev_err(task->cmdq->mbox.dev, "task 0x%p error\n", task);
+ WARN_ON(cmdq_thread_suspend(task->cmdq, thread) < 0);
+ next_task = list_first_entry_or_null(&thread->task_busy_list,
+ struct cmdq_task, list_entry);
+ if (next_task)
+ writel(next_task->pa_base, thread->base + CMDQ_THR_CURR_ADDR);
+ cmdq_thread_resume(thread);
+}
+
+static void cmdq_thread_irq_handler(struct cmdq *cmdq,
+ struct cmdq_thread *thread)
+{
+ struct cmdq_task *task, *tmp, *curr_task = NULL;
+ u32 curr_pa, irq_flag, task_end_pa;
+ bool err;
+
+ irq_flag = readl(thread->base + CMDQ_THR_IRQ_STATUS);
+ writel(~irq_flag, thread->base + CMDQ_THR_IRQ_STATUS);
+
+ /*
+ * When ISR call this function, another CPU core could run
+ * "release task" right before we acquire the spin lock, and thus
+ * reset / disable this GCE thread, so we need to check the enable
+ * bit of this GCE thread.
+ */
+ if (!(readl(thread->base + CMDQ_THR_ENABLE_TASK) & CMDQ_THR_ENABLED))
+ return;
+
+ if (irq_flag & CMDQ_THR_IRQ_ERROR)
+ err = true;
+ else if (irq_flag & CMDQ_THR_IRQ_DONE)
+ err = false;
+ else
+ return;
+
+ curr_pa = readl(thread->base + CMDQ_THR_CURR_ADDR);
+
+ list_for_each_entry_safe(task, tmp, &thread->task_busy_list,
+ list_entry) {
+ task_end_pa = task->pa_base + task->pkt->cmd_buf_size;
+ if (curr_pa >= task->pa_base && curr_pa < task_end_pa)
+ curr_task = task;
+
+ if (!curr_task || curr_pa == task_end_pa - CMDQ_INST_SIZE) {
+ cmdq_task_exec_done(task, false);
+ kfree(task);
+ } else if (err) {
+ cmdq_task_exec_done(task, true);
+ cmdq_task_handle_error(curr_task);
+ kfree(task);
+ }
+
+ if (curr_task)
+ break;
+ }
+
+ if (list_empty(&thread->task_busy_list)) {
+ cmdq_thread_disable(cmdq, thread);
+ clk_disable(cmdq->clock);
+ } else {
+ mod_timer(&thread->timeout,
+ jiffies + msecs_to_jiffies(CMDQ_TIMEOUT_MS));
+ }
+}
+
+static irqreturn_t cmdq_irq_handler(int irq, void *dev)
+{
+ struct cmdq *cmdq = dev;
+ unsigned long irq_status, flags = 0L;
+ int bit;
+
+ irq_status = readl(cmdq->base + CMDQ_CURR_IRQ_STATUS) & CMDQ_IRQ_MASK;
+ if (!(irq_status ^ CMDQ_IRQ_MASK))
+ return IRQ_NONE;
+
+ for_each_clear_bit(bit, &irq_status, fls(CMDQ_IRQ_MASK)) {
+ struct cmdq_thread *thread = &cmdq->thread[bit];
+
+ spin_lock_irqsave(&thread->chan->lock, flags);
+ cmdq_thread_irq_handler(cmdq, thread);
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+ }
+ return IRQ_HANDLED;
+}
+
+static void cmdq_thread_handle_timeout(unsigned long data)
+{
+ struct cmdq_thread *thread = (struct cmdq_thread *)data;
+ struct cmdq *cmdq = container_of(thread->chan->mbox, struct cmdq, mbox);
+ struct cmdq_task *task, *tmp;
+ unsigned long flags;
+
+ spin_lock_irqsave(&thread->chan->lock, flags);
+ WARN_ON(cmdq_thread_suspend(cmdq, thread) < 0);
+
+ /*
+ * Although IRQ is disabled, GCE continues to execute.
+ * It may have pending IRQ before GCE thread is suspended,
+ * so check this condition again.
+ */
+ cmdq_thread_irq_handler(cmdq, thread);
+
+ if (list_empty(&thread->task_busy_list)) {
+ cmdq_thread_resume(thread);
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+ return;
+ }
+
+ dev_err(cmdq->mbox.dev, "timeout\n");
+ list_for_each_entry_safe(task, tmp, &thread->task_busy_list,
+ list_entry) {
+ cmdq_task_exec_done(task, true);
+ kfree(task);
+ }
+
+ cmdq_thread_resume(thread);
+ cmdq_thread_disable(cmdq, thread);
+ clk_disable(cmdq->clock);
+ spin_unlock_irqrestore(&thread->chan->lock, flags);
+}
+
+static int cmdq_remove(struct platform_device *pdev)
+{
+ struct cmdq *cmdq = platform_get_drvdata(pdev);
+
+ mbox_controller_unregister(&cmdq->mbox);
+ clk_unprepare(cmdq->clock);
+ return 0;
+}
+
+static int cmdq_mbox_send_data(struct mbox_chan *chan, void *data)
+{
+ cmdq_task_exec(data, chan->con_priv);
+ return 0;
+}
+
+static int cmdq_mbox_startup(struct mbox_chan *chan)
+{
+ return 0;
+}
+
+static void cmdq_mbox_shutdown(struct mbox_chan *chan)
+{
+}
+
+static bool cmdq_mbox_last_tx_done(struct mbox_chan *chan)
+{
+ return true;
+}
+
+static const struct mbox_chan_ops cmdq_mbox_chan_ops = {
+ .send_data = cmdq_mbox_send_data,
+ .startup = cmdq_mbox_startup,
+ .shutdown = cmdq_mbox_shutdown,
+ .last_tx_done = cmdq_mbox_last_tx_done,
+};
+
+static struct mbox_chan *cmdq_xlate(struct mbox_controller *mbox,
+ const struct of_phandle_args *sp)
+{
+ int ind = sp->args[0];
+ struct cmdq_thread *thread;
+
+ if (ind >= mbox->num_chans)
+ return ERR_PTR(-EINVAL);
+
+ thread = mbox->chans[ind].con_priv;
+ thread->atomic_exec = (sp->args[1] != 0);
+ thread->chan = &mbox->chans[ind];
+
+ return &mbox->chans[ind];
+}
+
+static int cmdq_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct resource *res;
+ struct cmdq *cmdq;
+ int err, i;
+
+ cmdq = devm_kzalloc(dev, sizeof(*cmdq), GFP_KERNEL);
+ if (!cmdq)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ cmdq->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(cmdq->base)) {
+ dev_err(dev, "failed to ioremap gce\n");
+ return PTR_ERR(cmdq->base);
+ }
+
+ cmdq->irq = platform_get_irq(pdev, 0);
+ if (!cmdq->irq) {
+ dev_err(dev, "failed to get irq\n");
+ return -EINVAL;
+ }
+ err = devm_request_irq(dev, cmdq->irq, cmdq_irq_handler, IRQF_SHARED,
+ "mtk_cmdq", cmdq);
+ if (err < 0) {
+ dev_err(dev, "failed to register ISR (%d)\n", err);
+ return err;
+ }
+
+ dev_dbg(dev, "cmdq device: addr:0x%p, va:0x%p, irq:%d\n",
+ dev, cmdq->base, cmdq->irq);
+
+ cmdq->clock = devm_clk_get(dev, "gce");
+ if (IS_ERR(cmdq->clock)) {
+ dev_err(dev, "failed to get gce clk\n");
+ return PTR_ERR(cmdq->clock);
+ }
+
+ cmdq->mbox.dev = dev;
+ cmdq->mbox.chans = devm_kcalloc(dev, CMDQ_THR_MAX_COUNT,
+ sizeof(*cmdq->mbox.chans), GFP_KERNEL);
+ if (!cmdq->mbox.chans)
+ return -ENOMEM;
+
+ cmdq->mbox.num_chans = CMDQ_THR_MAX_COUNT;
+ cmdq->mbox.ops = &cmdq_mbox_chan_ops;
+ cmdq->mbox.of_xlate = cmdq_xlate;
+
+ /* make use of TXDONE_BY_ACK */
+ cmdq->mbox.txdone_irq = false;
+ cmdq->mbox.txdone_poll = false;
+
+ for (i = 0; i < ARRAY_SIZE(cmdq->thread); i++) {
+ cmdq->thread[i].base = cmdq->base + CMDQ_THR_BASE +
+ CMDQ_THR_SIZE * i;
+ INIT_LIST_HEAD(&cmdq->thread[i].task_busy_list);
+ init_timer(&cmdq->thread[i].timeout);
+ cmdq->thread[i].timeout.function = cmdq_thread_handle_timeout;
+ cmdq->thread[i].timeout.data = (unsigned long)&cmdq->thread[i];
+ cmdq->mbox.chans[i].con_priv = &cmdq->thread[i];
+ }
+
+ err = mbox_controller_register(&cmdq->mbox);
+ if (err < 0) {
+ dev_err(dev, "failed to register mailbox: %d\n", err);
+ return err;
+ }
+
+ platform_set_drvdata(pdev, cmdq);
+ WARN_ON(clk_prepare(cmdq->clock) < 0);
+ return 0;
+}
+
+static const struct of_device_id cmdq_of_ids[] = {
+ {.compatible = "mediatek,mt8173-gce",},
+ {}
+};
+
+static struct platform_driver cmdq_drv = {
+ .probe = cmdq_probe,
+ .remove = cmdq_remove,
+ .driver = {
+ .name = "mtk_cmdq",
+ .of_match_table = cmdq_of_ids,
+ }
+};
+
+builtin_platform_driver(cmdq_drv);
diff --git a/drivers/soc/mediatek/Kconfig b/drivers/soc/mediatek/Kconfig
index 0a4ea80..94651ed 100644
--- a/drivers/soc/mediatek/Kconfig
+++ b/drivers/soc/mediatek/Kconfig
@@ -1,6 +1,17 @@
#
# MediaTek SoC drivers
#
+config MTK_CMDQ
+ bool "MediaTek CMDQ Support"
+ depends on ARM64 && ( ARCH_MEDIATEK || COMPILE_TEST )
+ select MTK_CMDQ_MBOX
+ select MTK_INFRACFG
+ help
+ Say yes here to add support for the MediaTek Command Queue (CMDQ)
+ driver. The CMDQ is used to help read/write registers with critical
+ time limitation, such as updating display configuration during the
+ vblank.
+
config MTK_INFRACFG
bool "MediaTek INFRACFG Support"
depends on ARCH_MEDIATEK || COMPILE_TEST
diff --git a/drivers/soc/mediatek/Makefile b/drivers/soc/mediatek/Makefile
index 12998b0..64ce5ee 100644
--- a/drivers/soc/mediatek/Makefile
+++ b/drivers/soc/mediatek/Makefile
@@ -1,3 +1,4 @@
+obj-$(CONFIG_MTK_CMDQ) += mtk-cmdq-helper.o
obj-$(CONFIG_MTK_INFRACFG) += mtk-infracfg.o
obj-$(CONFIG_MTK_PMIC_WRAP) += mtk-pmic-wrap.o
obj-$(CONFIG_MTK_SCPSYS) += mtk-scpsys.o
diff --git a/drivers/soc/mediatek/mtk-cmdq-helper.c b/drivers/soc/mediatek/mtk-cmdq-helper.c
new file mode 100644
index 0000000..f4002bf
--- /dev/null
+++ b/drivers/soc/mediatek/mtk-cmdq-helper.c
@@ -0,0 +1,310 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/completion.h>
+#include <linux/errno.h>
+#include <linux/mailbox/mtk-cmdq-mailbox.h>
+#include <linux/of_address.h>
+
+#define CMDQ_SUBSYS_SHIFT 16
+#define CMDQ_ARG_A_WRITE_MASK 0xffff
+#define CMDQ_WRITE_ENABLE_MASK BIT(0)
+#define CMDQ_EOC_IRQ_EN BIT(0)
+#define CMDQ_EOC_CMD ((u64)((CMDQ_CODE_EOC << CMDQ_OP_CODE_SHIFT)) \
+ << 32 | CMDQ_EOC_IRQ_EN)
+
+struct cmdq_subsys {
+ u32 base;
+ int id;
+};
+
+static const struct cmdq_subsys gce_subsys[] = {
+ {0x1400, 1},
+ {0x1401, 2},
+ {0x1402, 3},
+};
+
+static int cmdq_subsys_base_to_id(u32 base)
+{
+ int i;
+
+ for (i = 0; i < ARRAY_SIZE(gce_subsys); i++)
+ if (gce_subsys[i].base == base)
+ return gce_subsys[i].id;
+ return -EFAULT;
+}
+
+static int cmdq_pkt_realloc_cmd_buffer(struct cmdq_pkt *pkt, size_t size)
+{
+ void *new_buf;
+
+ new_buf = krealloc(pkt->va_base, size, GFP_KERNEL | __GFP_ZERO);
+ if (!new_buf)
+ return -ENOMEM;
+ pkt->va_base = new_buf;
+ pkt->buf_size = size;
+ return 0;
+}
+
+struct cmdq_base *cmdq_register_device(struct device *dev)
+{
+ struct cmdq_base *cmdq_base;
+ struct resource res;
+ int subsys;
+ u32 base;
+
+ if (of_address_to_resource(dev->of_node, 0, &res))
+ return NULL;
+ base = (u32)res.start;
+
+ subsys = cmdq_subsys_base_to_id(base >> 16);
+ if (subsys < 0)
+ return NULL;
+
+ cmdq_base = devm_kmalloc(dev, sizeof(*cmdq_base), GFP_KERNEL);
+ if (!cmdq_base)
+ return NULL;
+ cmdq_base->subsys = subsys;
+ cmdq_base->base = base;
+
+ return cmdq_base;
+}
+EXPORT_SYMBOL(cmdq_register_device);
+
+struct cmdq_client *cmdq_mbox_create(struct device *dev, int index)
+{
+ struct cmdq_client *client;
+
+ client = kzalloc(sizeof(*client), GFP_KERNEL);
+ client->client.dev = dev;
+ client->client.tx_block = false;
+ client->chan = mbox_request_channel(&client->client, index);
+ return client;
+}
+EXPORT_SYMBOL(cmdq_mbox_create);
+
+void cmdq_mbox_destroy(struct cmdq_client *client)
+{
+ mbox_free_channel(client->chan);
+ kfree(client);
+}
+EXPORT_SYMBOL(cmdq_mbox_destroy);
+
+int cmdq_pkt_create(struct cmdq_pkt **pkt_ptr)
+{
+ struct cmdq_pkt *pkt;
+ int err;
+
+ pkt = kzalloc(sizeof(*pkt), GFP_KERNEL);
+ if (!pkt)
+ return -ENOMEM;
+ err = cmdq_pkt_realloc_cmd_buffer(pkt, PAGE_SIZE);
+ if (err < 0) {
+ kfree(pkt);
+ return err;
+ }
+ *pkt_ptr = pkt;
+ return 0;
+}
+EXPORT_SYMBOL(cmdq_pkt_create);
+
+void cmdq_pkt_destroy(struct cmdq_pkt *pkt)
+{
+ kfree(pkt->va_base);
+ kfree(pkt);
+}
+EXPORT_SYMBOL(cmdq_pkt_destroy);
+
+static bool cmdq_pkt_is_finalized(struct cmdq_pkt *pkt)
+{
+ u64 *expect_eoc;
+
+ if (pkt->cmd_buf_size < CMDQ_INST_SIZE << 1)
+ return false;
+
+ expect_eoc = pkt->va_base + pkt->cmd_buf_size - (CMDQ_INST_SIZE << 1);
+ if (*expect_eoc == CMDQ_EOC_CMD)
+ return true;
+
+ return false;
+}
+
+static int cmdq_pkt_append_command(struct cmdq_pkt *pkt, enum cmdq_code code,
+ u32 arg_a, u32 arg_b)
+{
+ u64 *cmd_ptr;
+ int err;
+
+ if (WARN_ON(cmdq_pkt_is_finalized(pkt)))
+ return -EBUSY;
+ if (unlikely(pkt->cmd_buf_size + CMDQ_INST_SIZE > pkt->buf_size)) {
+ err = cmdq_pkt_realloc_cmd_buffer(pkt, pkt->buf_size << 1);
+ if (err < 0)
+ return err;
+ }
+ cmd_ptr = pkt->va_base + pkt->cmd_buf_size;
+ (*cmd_ptr) = (u64)((code << CMDQ_OP_CODE_SHIFT) | arg_a) << 32 | arg_b;
+ pkt->cmd_buf_size += CMDQ_INST_SIZE;
+ return 0;
+}
+
+int cmdq_pkt_write(struct cmdq_pkt *pkt, u32 value, struct cmdq_base *base,
+ u32 offset)
+{
+ u32 arg_a = ((base->base + offset) & CMDQ_ARG_A_WRITE_MASK) |
+ (base->subsys << CMDQ_SUBSYS_SHIFT);
+ return cmdq_pkt_append_command(pkt, CMDQ_CODE_WRITE, arg_a, value);
+}
+EXPORT_SYMBOL(cmdq_pkt_write);
+
+int cmdq_pkt_write_mask(struct cmdq_pkt *pkt, u32 value,
+ struct cmdq_base *base, u32 offset, u32 mask)
+{
+ u32 offset_mask = offset;
+ int err;
+
+ if (mask != 0xffffffff) {
+ err = cmdq_pkt_append_command(pkt, CMDQ_CODE_MASK, 0, ~mask);
+ if (err < 0)
+ return err;
+ offset_mask |= CMDQ_WRITE_ENABLE_MASK;
+ }
+ return cmdq_pkt_write(pkt, value, base, offset_mask);
+}
+EXPORT_SYMBOL(cmdq_pkt_write_mask);
+
+static const u32 cmdq_event_value[CMDQ_MAX_EVENT] = {
+ /* Display start of frame(SOF) events */
+ [CMDQ_EVENT_DISP_OVL0_SOF] = 11,
+ [CMDQ_EVENT_DISP_OVL1_SOF] = 12,
+ [CMDQ_EVENT_DISP_RDMA0_SOF] = 13,
+ [CMDQ_EVENT_DISP_RDMA1_SOF] = 14,
+ [CMDQ_EVENT_DISP_RDMA2_SOF] = 15,
+ [CMDQ_EVENT_DISP_WDMA0_SOF] = 16,
+ [CMDQ_EVENT_DISP_WDMA1_SOF] = 17,
+ /* Display end of frame(EOF) events */
+ [CMDQ_EVENT_DISP_OVL0_EOF] = 39,
+ [CMDQ_EVENT_DISP_OVL1_EOF] = 40,
+ [CMDQ_EVENT_DISP_RDMA0_EOF] = 41,
+ [CMDQ_EVENT_DISP_RDMA1_EOF] = 42,
+ [CMDQ_EVENT_DISP_RDMA2_EOF] = 43,
+ [CMDQ_EVENT_DISP_WDMA0_EOF] = 44,
+ [CMDQ_EVENT_DISP_WDMA1_EOF] = 45,
+ /* Mutex end of frame(EOF) events */
+ [CMDQ_EVENT_MUTEX0_STREAM_EOF] = 53,
+ [CMDQ_EVENT_MUTEX1_STREAM_EOF] = 54,
+ [CMDQ_EVENT_MUTEX2_STREAM_EOF] = 55,
+ [CMDQ_EVENT_MUTEX3_STREAM_EOF] = 56,
+ [CMDQ_EVENT_MUTEX4_STREAM_EOF] = 57,
+ /* Display underrun events */
+ [CMDQ_EVENT_DISP_RDMA0_UNDERRUN] = 63,
+ [CMDQ_EVENT_DISP_RDMA1_UNDERRUN] = 64,
+ [CMDQ_EVENT_DISP_RDMA2_UNDERRUN] = 65,
+};
+
+int cmdq_pkt_wfe(struct cmdq_pkt *pkt, enum cmdq_event event)
+{
+ u32 arg_b;
+
+ if (event >= CMDQ_MAX_EVENT || event < 0)
+ return -EINVAL;
+
+ /*
+ * WFE arg_b
+ * bit 0-11: wait value
+ * bit 15: 1 - wait, 0 - no wait
+ * bit 16-27: update value
+ * bit 31: 1 - update, 0 - no update
+ */
+ arg_b = CMDQ_WFE_UPDATE | CMDQ_WFE_WAIT | CMDQ_WFE_WAIT_VALUE;
+ return cmdq_pkt_append_command(pkt, CMDQ_CODE_WFE,
+ cmdq_event_value[event], arg_b);
+}
+EXPORT_SYMBOL(cmdq_pkt_wfe);
+
+int cmdq_pkt_clear_event(struct cmdq_pkt *pkt, enum cmdq_event event)
+{
+ if (event >= CMDQ_MAX_EVENT || event < 0)
+ return -EINVAL;
+
+ return cmdq_pkt_append_command(pkt, CMDQ_CODE_WFE,
+ cmdq_event_value[event], CMDQ_WFE_UPDATE);
+}
+EXPORT_SYMBOL(cmdq_pkt_clear_event);
+
+static int cmdq_pkt_finalize(struct cmdq_pkt *pkt)
+{
+ int err;
+
+ if (cmdq_pkt_is_finalized(pkt))
+ return 0;
+
+ /* insert EOC and generate IRQ for each command iteration */
+ err = cmdq_pkt_append_command(pkt, CMDQ_CODE_EOC, 0, CMDQ_EOC_IRQ_EN);
+ if (err < 0)
+ return err;
+
+ /* JUMP to end */
+ err = cmdq_pkt_append_command(pkt, CMDQ_CODE_JUMP, 0, CMDQ_JUMP_PASS);
+ if (err < 0)
+ return err;
+
+ return 0;
+}
+
+int cmdq_pkt_flush_async(struct cmdq_client *client, struct cmdq_pkt *pkt,
+ cmdq_async_flush_cb cb, void *data)
+{
+ int err;
+
+ err = cmdq_pkt_finalize(pkt);
+ if (err < 0)
+ return err;
+
+ pkt->cb.cb = cb;
+ pkt->cb.data = data;
+
+ mbox_send_message(client->chan, pkt);
+ /* We can send next packet immediately, so just call txdone. */
+ mbox_client_txdone(client->chan, 0);
+
+ return 0;
+}
+EXPORT_SYMBOL(cmdq_pkt_flush_async);
+
+struct cmdq_flush_completion {
+ struct completion cmplt;
+ bool err;
+};
+
+static void cmdq_pkt_flush_cb(struct cmdq_cb_data data)
+{
+ struct cmdq_flush_completion *cmplt = data.data;
+
+ cmplt->err = data.err;
+ complete(&cmplt->cmplt);
+}
+
+int cmdq_pkt_flush(struct cmdq_client *client, struct cmdq_pkt *pkt)
+{
+ struct cmdq_flush_completion cmplt;
+ int err;
+
+ init_completion(&cmplt.cmplt);
+ err = cmdq_pkt_flush_async(client, pkt, cmdq_pkt_flush_cb, &cmplt);
+ if (err < 0)
+ return err;
+ wait_for_completion(&cmplt.cmplt);
+ return cmplt.err ? -EFAULT : 0;
+}
+EXPORT_SYMBOL(cmdq_pkt_flush);
diff --git a/include/linux/mailbox/mtk-cmdq-mailbox.h b/include/linux/mailbox/mtk-cmdq-mailbox.h
new file mode 100644
index 0000000..131b8b3
--- /dev/null
+++ b/include/linux/mailbox/mtk-cmdq-mailbox.h
@@ -0,0 +1,67 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MTK_CMDQ_MAILBOX_H__
+#define __MTK_CMDQ_MAILBOX_H__
+
+#include <linux/slab.h>
+#include <linux/soc/mediatek/mtk-cmdq.h>
+
+#define CMDQ_INST_SIZE 8 /* instruction is 64-bit */
+#define CMDQ_OP_CODE_SHIFT 24
+#define CMDQ_JUMP_PASS CMDQ_INST_SIZE
+
+#define CMDQ_WFE_UPDATE BIT(31)
+#define CMDQ_WFE_WAIT BIT(15)
+#define CMDQ_WFE_WAIT_VALUE 0x1
+
+/*
+ * CMDQ_CODE_MASK:
+ * set write mask
+ * format: op mask
+ * CMDQ_CODE_WRITE:
+ * write value into target register
+ * format: op subsys address value
+ * CMDQ_CODE_JUMP:
+ * jump by offset
+ * format: op offset
+ * CMDQ_CODE_WFE:
+ * wait for event and clear
+ * it is just clear if no wait
+ * format: [wait] op event update:1 to_wait:1 wait:1
+ * [clear] op event update:1 to_wait:0 wait:0
+ * CMDQ_CODE_EOC:
+ * end of command
+ * format: op irq_flag
+ */
+enum cmdq_code {
+ CMDQ_CODE_MASK = 0x02,
+ CMDQ_CODE_WRITE = 0x04,
+ CMDQ_CODE_JUMP = 0x10,
+ CMDQ_CODE_WFE = 0x20,
+ CMDQ_CODE_EOC = 0x40,
+};
+
+struct cmdq_task_cb {
+ cmdq_async_flush_cb cb;
+ void *data;
+};
+
+struct cmdq_pkt {
+ void *va_base;
+ size_t cmd_buf_size; /* command occupied size */
+ size_t buf_size; /* real buffer size */
+ struct cmdq_task_cb cb;
+};
+
+#endif /* __MTK_CMDQ_MAILBOX_H__ */
diff --git a/include/linux/soc/mediatek/mtk-cmdq.h b/include/linux/soc/mediatek/mtk-cmdq.h
new file mode 100644
index 0000000..7320837
--- /dev/null
+++ b/include/linux/soc/mediatek/mtk-cmdq.h
@@ -0,0 +1,182 @@
+/*
+ * Copyright (c) 2015 MediaTek Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef __MTK_CMDQ_H__
+#define __MTK_CMDQ_H__
+
+#include <linux/mailbox_client.h>
+#include <linux/platform_device.h>
+#include <linux/types.h>
+
+/* display events in command queue(CMDQ) */
+enum cmdq_event {
+ /* Display start of frame(SOF) events */
+ CMDQ_EVENT_DISP_OVL0_SOF,
+ CMDQ_EVENT_DISP_OVL1_SOF,
+ CMDQ_EVENT_DISP_RDMA0_SOF,
+ CMDQ_EVENT_DISP_RDMA1_SOF,
+ CMDQ_EVENT_DISP_RDMA2_SOF,
+ CMDQ_EVENT_DISP_WDMA0_SOF,
+ CMDQ_EVENT_DISP_WDMA1_SOF,
+ /* Display end of frame(EOF) events */
+ CMDQ_EVENT_DISP_OVL0_EOF,
+ CMDQ_EVENT_DISP_OVL1_EOF,
+ CMDQ_EVENT_DISP_RDMA0_EOF,
+ CMDQ_EVENT_DISP_RDMA1_EOF,
+ CMDQ_EVENT_DISP_RDMA2_EOF,
+ CMDQ_EVENT_DISP_WDMA0_EOF,
+ CMDQ_EVENT_DISP_WDMA1_EOF,
+ /* Mutex end of frame(EOF) events */
+ CMDQ_EVENT_MUTEX0_STREAM_EOF,
+ CMDQ_EVENT_MUTEX1_STREAM_EOF,
+ CMDQ_EVENT_MUTEX2_STREAM_EOF,
+ CMDQ_EVENT_MUTEX3_STREAM_EOF,
+ CMDQ_EVENT_MUTEX4_STREAM_EOF,
+ /* Display underrun events */
+ CMDQ_EVENT_DISP_RDMA0_UNDERRUN,
+ CMDQ_EVENT_DISP_RDMA1_UNDERRUN,
+ CMDQ_EVENT_DISP_RDMA2_UNDERRUN,
+ /* Keep this at the end */
+ CMDQ_MAX_EVENT,
+};
+
+struct cmdq_cb_data {
+ bool err;
+ void *data;
+};
+
+typedef void (*cmdq_async_flush_cb)(struct cmdq_cb_data data);
+
+struct cmdq_pkt;
+
+struct cmdq_base {
+ int subsys;
+ u32 base;
+};
+
+struct cmdq_client {
+ struct mbox_client client;
+ struct mbox_chan *chan;
+};
+
+/**
+ * cmdq_register_device() - register device which needs CMDQ
+ * @dev: device for CMDQ to access its registers
+ *
+ * Return: cmdq_base pointer or NULL for failed
+ */
+struct cmdq_base *cmdq_register_device(struct device *dev);
+
+/**
+ * cmdq_mbox_create() - create CMDQ mailbox client and channel
+ * @dev: device of CMDQ mailbox client
+ * @index: index of CMDQ mailbox channel
+ *
+ * Return: CMDQ mailbox client pointer
+ */
+struct cmdq_client *cmdq_mbox_create(struct device *dev, int index);
+
+/**
+ * cmdq_mbox_destroy() - destroy CMDQ mailbox client and channel
+ * @client: the CMDQ mailbox client
+ */
+void cmdq_mbox_destroy(struct cmdq_client *client);
+
+/**
+ * cmdq_pkt_create() - create a CMDQ packet
+ * @pkt_ptr: CMDQ packet pointer to retrieve cmdq_pkt
+ *
+ * Return: 0 for success; else the error code is returned
+ */
+int cmdq_pkt_create(struct cmdq_pkt **pkt_ptr);
+
+/**
+ * cmdq_pkt_destroy() - destroy the CMDQ packet
+ * @pkt: the CMDQ packet
+ */
+void cmdq_pkt_destroy(struct cmdq_pkt *pkt);
+
+/**
+ * cmdq_pkt_write() - append write command to the CMDQ packet
+ * @pkt: the CMDQ packet
+ * @value: the specified target register value
+ * @base: the CMDQ base
+ * @offset: register offset from module base
+ *
+ * Return: 0 for success; else the error code is returned
+ */
+int cmdq_pkt_write(struct cmdq_pkt *pkt, u32 value,
+ struct cmdq_base *base, u32 offset);
+
+/**
+ * cmdq_pkt_write_mask() - append write command with mask to the CMDQ packet
+ * @pkt: the CMDQ packet
+ * @value: the specified target register value
+ * @base: the CMDQ base
+ * @offset: register offset from module base
+ * @mask: the specified target register mask
+ *
+ * Return: 0 for success; else the error code is returned
+ */
+int cmdq_pkt_write_mask(struct cmdq_pkt *pkt, u32 value,
+ struct cmdq_base *base, u32 offset, u32 mask);
+
+/**
+ * cmdq_pkt_wfe() - append wait for event command to the CMDQ packet
+ * @pkt: the CMDQ packet
+ * @event: the desired event type to "wait and CLEAR"
+ *
+ * Return: 0 for success; else the error code is returned
+ */
+int cmdq_pkt_wfe(struct cmdq_pkt *pkt, enum cmdq_event event);
+
+/**
+ * cmdq_pkt_clear_event() - append clear event command to the CMDQ packet
+ * @pkt: the CMDQ packet
+ * @event: the desired event to be cleared
+ *
+ * Return: 0 for success; else the error code is returned
+ */
+int cmdq_pkt_clear_event(struct cmdq_pkt *pkt, enum cmdq_event event);
+
+/**
+ * cmdq_pkt_flush() - trigger CMDQ to execute the CMDQ packet
+ * @client: the CMDQ mailbox client
+ * @pkt: the CMDQ packet
+ *
+ * Return: 0 for success; else the error code is returned
+ *
+ * Trigger CMDQ to execute the CMDQ packet. Note that this is a
+ * synchronous flush function. When the function returned, the recorded
+ * commands have been done.
+ */
+int cmdq_pkt_flush(struct cmdq_client *client, struct cmdq_pkt *pkt);
+
+/**
+ * cmdq_pkt_flush_async() - trigger CMDQ to asynchronously execute the CMDQ
+ * packet and call back at the end of done packet
+ * @client: the CMDQ mailbox client
+ * @pkt: the CMDQ packet
+ * @cb: called at the end of done packet
+ * @data: this data will pass back to cb
+ *
+ * Return: 0 for success; else the error code is returned
+ *
+ * Trigger CMDQ to asynchronously execute the CMDQ packet and call back
+ * at the end of done packet. Note that this is an ASYNC function. When the
+ * function returned, it may or may not be finished.
+ */
+int cmdq_pkt_flush_async(struct cmdq_client *client, struct cmdq_pkt *pkt,
+ cmdq_async_flush_cb cb, void *data);
+
+#endif /* __MTK_CMDQ_H__ */
--
1.9.1
^ permalink raw reply related
* [PATCH v16 1/5] dt-bindings: soc: Add documentation for the MediaTek GCE unit
From: HS Liao @ 2016-11-01 11:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477999698-6288-1-git-send-email-hs.liao@mediatek.com>
This adds documentation for the MediaTek Global Command Engine (GCE) unit
found in MT8173 SoCs.
Signed-off-by: HS Liao <hs.liao@mediatek.com>
Acked-by: Rob Herring <robh@kernel.org>
---
.../devicetree/bindings/mailbox/mtk-gce.txt | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mailbox/mtk-gce.txt
diff --git a/Documentation/devicetree/bindings/mailbox/mtk-gce.txt b/Documentation/devicetree/bindings/mailbox/mtk-gce.txt
new file mode 100644
index 0000000..d2d3ccb
--- /dev/null
+++ b/Documentation/devicetree/bindings/mailbox/mtk-gce.txt
@@ -0,0 +1,43 @@
+MediaTek GCE
+===============
+
+The Global Command Engine (GCE) is used to help read/write registers with
+critical time limitation, such as updating display configuration during the
+vblank. The GCE can be used to implement the Command Queue (CMDQ) driver.
+
+CMDQ driver uses mailbox framework for communication. Please refer to
+mailbox.txt for generic information about mailbox device-tree bindings.
+
+Required properties:
+- compatible: Must be "mediatek,mt8173-gce"
+- reg: Address range of the GCE unit
+- interrupts: The interrupt signal from the GCE block
+- clock: Clocks according to the common clock binding
+- clock-names: Must be "gce" to stand for GCE clock
+- #mbox-cells: Should be 2
+
+Required properties for a client device:
+- mboxes: client use mailbox to communicate with GCE, it should have this
+ property and list of phandle, mailbox channel specifiers, and atomic
+ execution flag.
+
+Example:
+
+ gce: gce at 10212000 {
+ compatible = "mediatek,mt8173-gce";
+ reg = <0 0x10212000 0 0x1000>;
+ interrupts = <GIC_SPI 135 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_GCE>;
+ clock-names = "gce";
+
+ #mbox-cells = <2>;
+ };
+
+Example for a client device:
+
+ mmsys: clock-controller at 14000000 {
+ compatible = "mediatek,mt8173-mmsys";
+ mboxes = <&gce 0 1 /* main display with atomic execution */
+ &gce 1 1>; /* sub display with atomic execution */
+ ...
+ };
--
1.9.1
^ permalink raw reply related
* [PATCH v16 0/5] Mediatek MT8173 CMDQ support
From: HS Liao @ 2016-11-01 11:28 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
This is Mediatek MT8173 Command Queue(CMDQ) driver. The CMDQ is used
to help write registers with critical time limitation, such as
updating display configuration during the vblank. It controls Global
Command Engine (GCE) hardware to achieve this requirement.
These patches have a build dependency on top of v4.9-rc1.
Changes since v15:
- separate "suspend and resume" patch from "save energy" patch
- don't stop running tasks in cmdq_suspend()
(i.e. leave no running tasks guarantee to clients)
Best regards,
HS Liao
HS Liao (5):
dt-bindings: soc: Add documentation for the MediaTek GCE unit
CMDQ: Mediatek CMDQ driver
arm64: dts: mt8173: Add GCE node
CMDQ: suspend and resume
CMDQ: save energy
.../devicetree/bindings/mailbox/mtk-gce.txt | 43 ++
arch/arm64/boot/dts/mediatek/mt8173.dtsi | 10 +
drivers/mailbox/Kconfig | 10 +
drivers/mailbox/Makefile | 2 +
drivers/mailbox/mtk-cmdq-mailbox.c | 632 +++++++++++++++++++++
drivers/soc/mediatek/Kconfig | 11 +
drivers/soc/mediatek/Makefile | 1 +
drivers/soc/mediatek/mtk-cmdq-helper.c | 310 ++++++++++
include/linux/mailbox/mtk-cmdq-mailbox.h | 67 +++
include/linux/soc/mediatek/mtk-cmdq.h | 182 ++++++
10 files changed, 1268 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mailbox/mtk-gce.txt
create mode 100644 drivers/mailbox/mtk-cmdq-mailbox.c
create mode 100644 drivers/soc/mediatek/mtk-cmdq-helper.c
create mode 100644 include/linux/mailbox/mtk-cmdq-mailbox.h
create mode 100644 include/linux/soc/mediatek/mtk-cmdq.h
--
1.9.1
^ permalink raw reply
* [PATCH 2/3] KVM: arm/arm64: Add ARM arch timer interrupts ABI
From: Peter Maydell @ 2016-11-01 11:26 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20160927190806.22988-3-christoffer.dall@linaro.org>
On 27 September 2016 at 20:08, Christoffer Dall
<christoffer.dall@linaro.org> wrote:
> From: Alexander Graf <agraf@suse.de>
>
> We have 2 modes for dealing with interrupts in the ARM world. We can
> either handle them all using hardware acceleration through the vgic or
> we can emulate a gic in user space and only drive CPU IRQ pins from
> there.
>
> Unfortunately, when driving IRQs from user space, we never tell user
> space about timer events that may result in interrupt line state
> changes, so we lose out on timer events if we run with user space gic
> emulation.
>
> Define an ABI to publish the timer output level to userspace.
>
> Signed-off-by: Alexander Graf <agraf@suse.de>
> Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
> Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
> ---
> Documentation/virtual/kvm/api.txt | 29 +++++++++++++++++++++++++++++
> arch/arm/include/uapi/asm/kvm.h | 2 ++
> arch/arm64/include/uapi/asm/kvm.h | 2 ++
> include/uapi/linux/kvm.h | 6 ++++++
> 4 files changed, 39 insertions(+)
>
> diff --git a/Documentation/virtual/kvm/api.txt b/Documentation/virtual/kvm/api.txt
> index 739db9a..2adf600 100644
> --- a/Documentation/virtual/kvm/api.txt
> +++ b/Documentation/virtual/kvm/api.txt
> @@ -3928,3 +3928,32 @@ In order to use SynIC, it has to be activated by setting this
> capability via KVM_ENABLE_CAP ioctl on the vcpu fd. Note that this
> will disable the use of APIC hardware virtualization even if supported
> by the CPU, as it's incompatible with SynIC auto-EOI behavior.
> +
> +8.3 KVM_CAP_ARM_TIMER
> +
> +Architectures: arm, arm64
> +This capability, if KVM_CHECK_EXTENSION indicates that it is available, means
> +that if userspace creates a VM without an in-kernel interrupt controller, it
> +will be notified of changes to the output level of ARM architected timers
> +presented to the VM. For such VMs, on every return to userspace, the kernel
> +updates the vcpu's run->s.regs.timer_irq_level field to represent the actual
> +output level of the timers.
> +
> +Whenever kvm detects a change in the timer output level, kvm guarantees at
> +least one return to userspace before running the VM. This exit could either
> +be a KVM_EXIT_INTR or any other exit event, like KVM_EXIT_MMIO. This way,
> +userspace can always sample the timer output level and re-compute the state of
> +the userspace interrupt controller. Userspace should always check the state
> +of run->s.regs.timer_irq_level on every kvm exit. The value in
> +run->s.regs.timer_irq_level should be considered a level triggered interrupt
> +signal.
> +
> +The field run->s.regs.timer_irq_level is available independent of
> +run->kvm_valid_regs or run->kvm_dirty_regs bits.
> +
> +Currently the following bits are defined for the timer_irq_level bitmap:
> +
> + KVM_ARM_TIMER_VTIMER - virtual timer
> +
> +Future versions of kvm may implement additional timer events. These will get
> +indicated by additional KVM_CAP extensions.
This API looks good to me generally. My only question is whether we
want to name the struct fields so they're not specifically talking
about timer interrupts. For instance we probably want to expose the
vPMU interrupt line to userspace too. We could do that by adding another
struct field pmu_irq_level, but we could equally just assign it a bit
in the existing irq_level field.
Possible current and future outbound interrupt lines (some of these
would only show up in some unlikely or lots-of-implementation-needed
cases, I'm just trying to produce an exhaustive list):
* virtual timer
* physical timer
* hyp timer (nested virtualization case)
* secure timer (unlikely but maybe if EL3 is ever supported inside a VM)
* gic maintenance interrupt (nested virt again)
* PMU interrupt
The kernel doesn't know which interrupt number these would be wired
up to, so they're all just arbitrary outputs, and you could put them
in one field or split them up into multiple fields, it doesn't make
much difference.
thanks
-- PMM
^ permalink raw reply
* [PATCH 2/3] ARM: imx: mach-imx6ul: add imx6ull support
From: Peter Chen @ 2016-11-01 10:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAOMZO5AsF8s9Ff2NHQ+j2_xSBNEzGY6bGLK-kgvx-aST+K2PNQ@mail.gmail.com>
>
>On Tue, Nov 1, 2016 at 1:02 AM, Peter Chen <peter.chen@nxp.com> wrote:
>> imx6ull is derived SoC from imx6ul.
>>
>> Signed-off-by: Peter Chen <peter.chen@nxp.com>
>> ---
>> arch/arm/mach-imx/mach-imx6ul.c | 3 ++-
>> 1 file changed, 2 insertions(+), 1 deletion(-)
>>
>> diff --git a/arch/arm/mach-imx/mach-imx6ul.c
>> b/arch/arm/mach-imx/mach-imx6ul.c index 58a2b88..0b24630 100644
>> --- a/arch/arm/mach-imx/mach-imx6ul.c
>> +++ b/arch/arm/mach-imx/mach-imx6ul.c
>> @@ -89,10 +89,11 @@ static void __init imx6ul_init_late(void)
>>
>> static const char * const imx6ul_dt_compat[] __initconst = {
>> "fsl,imx6ul",
>> + "fsl,imx6ull",
>> NULL,
>> };
>>
>> -DT_MACHINE_START(IMX6UL, "Freescale i.MX6 Ultralite (Device Tree)")
>> +DT_MACHINE_START(IMX6UL, "Freescale i.MX6 UltraLite (Device Tree)")
>
>Is this change really needed?
This change does not be related with imx6ull support, but also a needed change since
the formal name is capital letter "L", if you are concerned with that, I can delete this
change.
Peter
^ permalink raw reply
* [PATCH] bus: vexpress-config: fix device reference leak
From: Johan Hovold @ 2016-11-01 10:43 UTC (permalink / raw)
To: linux-arm-kernel
Make sure to drop the reference to the parent device taken by
class_find_device() after populating the bus.
Fixes: 3b9334ac835b ("mfd: vexpress: Convert custom func API to regmap")
Signed-off-by: Johan Hovold <johan@kernel.org>
---
drivers/bus/vexpress-config.c | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/drivers/bus/vexpress-config.c b/drivers/bus/vexpress-config.c
index 9efdf1de4035..493e7b9fc813 100644
--- a/drivers/bus/vexpress-config.c
+++ b/drivers/bus/vexpress-config.c
@@ -171,6 +171,7 @@ static int vexpress_config_populate(struct device_node *node)
{
struct device_node *bridge;
struct device *parent;
+ int ret;
bridge = of_parse_phandle(node, "arm,vexpress,config-bridge", 0);
if (!bridge)
@@ -182,7 +183,11 @@ static int vexpress_config_populate(struct device_node *node)
if (WARN_ON(!parent))
return -ENODEV;
- return of_platform_populate(node, NULL, NULL, parent);
+ ret = of_platform_populate(node, NULL, NULL, parent);
+
+ put_device(parent);
+
+ return ret;
}
static int __init vexpress_config_init(void)
--
2.7.3
^ permalink raw reply related
* [PATCH v2 5/5] ARM: dts: da850-lcdk: add tilcdc panel node
From: Tomi Valkeinen @ 2016-11-01 10:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <3e8671aa-e59d-4595-c323-af9e6a0ad615@ti.com>
On 01/11/16 12:26, Sekhar Nori wrote:
> On Monday 31 October 2016 08:15 PM, Bartosz Golaszewski wrote:
>> The tilcdc driver is not yet ready for working together with the
>> dumb-vga-dac drm bridge. While the work on enabling drm_bridge
>> support in tilcdc continues, enable the VGA connector on da850-lcdk
>> with the following workaround: use the tilcdc-panel driver with
>> a set of common (and tested) resolutions.
>>
>> Once the drm bridge support is complete, we'll remove the node added
>> by this patch and use the correct solution. This change will be
>> transparent for the user.
>>
>> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
>
> I dont think this can be applied. If this goes in v4.10, then the DT
> blob becomes an ABI and driver will have to support tilcdc-panel driver
> for DA850 forever.
>
> Its probably better to wait for the proper driver support to arrive.
Agreed, NAK for this.
Tomi
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 819 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161101/c00353af/attachment.sig>
^ permalink raw reply
* [PATCH] ARM: davinci: da850: Fix pwm name matching
From: Sekhar Nori @ 2016-11-01 10:31 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <3fd93d1b-8ba2-5440-e37d-0c55928e7e51@lechnology.com>
On Monday 31 October 2016 08:18 PM, David Lechner wrote:
> On 10/31/2016 05:18 AM, Sekhar Nori wrote:
>> On Tuesday 25 October 2016 11:24 PM, David Lechner wrote:
>>> This fixes pwm name matching for DA850 familiy devices. When using
>>> device
>>> tree, the da850_auxdata_lookup[] table caused pwm devices to have the
>>> exact
>>> same name, which caused errors when trying to register the devices.
>>>
>>> The names for clock matching in da850_clks[] also have to be updated to
>>> to exactly match in order for the clock lookup to work correctly.
>>>
>>> Signed-off-by: David Lechner <david@lechnology.com>
>>> ---
>>>
>>> Tested working on LEGO MINDSTORMS EV3.
>>>
>>>
>>> arch/arm/mach-davinci/da850.c | 10 +++++++---
>>> arch/arm/mach-davinci/da8xx-dt.c | 10 +++++-----
>>> 2 files changed, 12 insertions(+), 8 deletions(-)
>>>
>>> diff --git a/arch/arm/mach-davinci/da850.c
>>> b/arch/arm/mach-davinci/da850.c
>>> index ed3d0e9..6b78a8f 100644
>>> --- a/arch/arm/mach-davinci/da850.c
>>> +++ b/arch/arm/mach-davinci/da850.c
>>> @@ -510,9 +510,13 @@ static struct clk_lookup da850_clks[] = {
>>> CLK("vpif", NULL, &vpif_clk),
>>> CLK("ahci_da850", NULL, &sata_clk),
>>> CLK("davinci-rproc.0", NULL, &dsp_clk),
>>> - CLK("ehrpwm", "fck", &ehrpwm_clk),
>>> - CLK("ehrpwm", "tbclk", &ehrpwm_tbclk),
>>> - CLK("ecap", "fck", &ecap_clk),
>>> + CLK("ehrpwm.0", "fck", &ehrpwm_clk),
>>> + CLK("ehrpwm.0", "tbclk", &ehrpwm_tbclk),
>>> + CLK("ehrpwm.1", "fck", &ehrpwm_clk),
>>> + CLK("ehrpwm.1", "tbclk", &ehrpwm_tbclk),
>>> + CLK("ecap.0", "fck", &ecap_clk),
>>> + CLK("ecap.1", "fck", &ecap_clk),
>>> + CLK("ecap.2", "fck", &ecap_clk),
>>
>> This has exposed a limitation of DaVinci clock framework. The struct clk
>> are stored as a linked list themselves. So a node repeating in the table
>> above will create a loop in the linked list. This is easily seen on the
>> LCDK board. davinci_clk_disable_unused() never returns. PWMs are unused
>> on that board.
>>
>> There is no "simple" solution to this AFAICS. One solution is to
>> separate the iterator from the clock hardware structure and use struct
>> clk_hw available in struct clk_lookup.
>>
>> Or move DaVinci to common clock framework. This is of course preferred
>> but much more involved as all 6 supported SoCs have to be moved together.
>>
>> Thanks,
>> Sekhar
>>
>>
>
> The simple solution for now could be to make child clocks for each of
> these that simply enable the parent clock. e.g. ehrpwm0_clk and
> ehpwm1_clk are children of ehrpwm_clk, etc.
That sounds good. I saw the v2 patch you sent and it looks good. I
noticed that aemif clock is repeated in da850.c too. That needs fixing.
> Looking at da830.c, it looks like the solution was to make multiple
> clocks that use the same LPSC, but this does not seem right to me.
The PWM clock definitions there are definitely wrong. It should be
fixed. Looks like its been like that forever.
Thanks,
Sekhar
^ permalink raw reply
* [PATCH 2/3] ARM: imx: mach-imx6ul: add imx6ull support
From: Fabio Estevam @ 2016-11-01 10:29 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477969343-19887-3-git-send-email-peter.chen@nxp.com>
On Tue, Nov 1, 2016 at 1:02 AM, Peter Chen <peter.chen@nxp.com> wrote:
> imx6ull is derived SoC from imx6ul.
>
> Signed-off-by: Peter Chen <peter.chen@nxp.com>
> ---
> arch/arm/mach-imx/mach-imx6ul.c | 3 ++-
> 1 file changed, 2 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/mach-imx/mach-imx6ul.c b/arch/arm/mach-imx/mach-imx6ul.c
> index 58a2b88..0b24630 100644
> --- a/arch/arm/mach-imx/mach-imx6ul.c
> +++ b/arch/arm/mach-imx/mach-imx6ul.c
> @@ -89,10 +89,11 @@ static void __init imx6ul_init_late(void)
>
> static const char * const imx6ul_dt_compat[] __initconst = {
> "fsl,imx6ul",
> + "fsl,imx6ull",
> NULL,
> };
>
> -DT_MACHINE_START(IMX6UL, "Freescale i.MX6 Ultralite (Device Tree)")
> +DT_MACHINE_START(IMX6UL, "Freescale i.MX6 UltraLite (Device Tree)")
Is this change really needed?
^ permalink raw reply
* [PATCH v2 5/5] ARM: dts: da850-lcdk: add tilcdc panel node
From: Sekhar Nori @ 2016-11-01 10:26 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477925138-23457-6-git-send-email-bgolaszewski@baylibre.com>
On Monday 31 October 2016 08:15 PM, Bartosz Golaszewski wrote:
> The tilcdc driver is not yet ready for working together with the
> dumb-vga-dac drm bridge. While the work on enabling drm_bridge
> support in tilcdc continues, enable the VGA connector on da850-lcdk
> with the following workaround: use the tilcdc-panel driver with
> a set of common (and tested) resolutions.
>
> Once the drm bridge support is complete, we'll remove the node added
> by this patch and use the correct solution. This change will be
> transparent for the user.
>
> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
I dont think this can be applied. If this goes in v4.10, then the DT
blob becomes an ABI and driver will have to support tilcdc-panel driver
for DA850 forever.
Its probably better to wait for the proper driver support to arrive.
Thanks,
Sekhar
^ permalink raw reply
* [PATCH v2 2/5] ARM: bus: da8xx-mstpri: new driver
From: Sekhar Nori @ 2016-11-01 10:21 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477925138-23457-3-git-send-email-bgolaszewski@baylibre.com>
On Monday 31 October 2016 08:15 PM, Bartosz Golaszewski wrote:
> Create the driver for the da8xx master peripheral priority
> configuration and implement support for writing to the three
> Master Priority registers on da850 SoCs.
>
> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Thanks,
Sekhar
^ permalink raw reply
* [PATCH v2 1/5] ARM: memory: da8xx-ddrctl: new driver
From: Sekhar Nori @ 2016-11-01 10:10 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477925138-23457-2-git-send-email-bgolaszewski@baylibre.com>
On Monday 31 October 2016 08:15 PM, Bartosz Golaszewski wrote:
> Create a new driver for the da8xx DDR2/mDDR controller and implement
> support for writing to the Peripheral Bus Burst Priority Register.
>
> Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Sekhar Nori <nsekhar@ti.com>
Thanks,
Sekhar
^ permalink raw reply
* [PATCH v8 3/3] ARM: davinci: da8xx: register USB PHY clocks in the DT file
From: Sekhar Nori @ 2016-11-01 9:58 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477946841-16126-4-git-send-email-david@lechnology.com>
On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> From: Axel Haslam <ahaslam@baylibre.com>
>
> The usb20_phy clock needs to be registered for the driver to be able
> to get and enable a clock. Currently the usb phy clocks are registered
> form board files, which will not be called during a device tree based
> boot.
>
> To be able to probe correctly usb form a device tree boot, register
> the usb phy clocks form the DT specific init.
>
> Unfourtunatly, davinci does not have proper clock support on device tree
> yet, so by registering the clock form de DT specific file we are
> forced to hardcode the parent clock, and cannot select refclkin as
> parent for any of the phy clocks of the da850 family.
>
> As none of the current da850 based boards currently in mainline use
> refclkin as source. I guess we can live with this limitation until clocks
> are correctly represented through CCF/device tree.
>
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
> [Added error checking]
> Signed-off-by: David Lechner <david@lechnology.com>
Applied to v4.10/soc with some typo fixes.
s/form/from
s/Unfourtunatly/Unfortunately
s/de/the
Thanks,
Sekhar
^ permalink raw reply
* [PATCH v8 2/3] ARM: davinci: da8xx: add usb phy clocks
From: Sekhar Nori @ 2016-11-01 9:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1477946841-16126-3-git-send-email-david@lechnology.com>
On Tuesday 01 November 2016 02:17 AM, David Lechner wrote:
> Up to this point, the USB phy clock configuration was handled manually in
> the board files and in the usb drivers. This adds proper clocks so that
> the usb drivers can use clk_get and clk_enable and not have to worry about
> the details. Also, the related code is removed from the board files and
> replaced with the new clock registration functions.
>
> This also removes the #if IS_ENABLED(CONFIG_USB_MUSB_HDRC) around the musb
> declaration and renames the musb platform device so that we can reference
> it from the usb20 clock even if the musb device is not used.
>
> Signed-off-by: David Lechner <david@lechnology.com>
> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
Applied to v4.10/soc
Thanks,
Sekhar
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox