* [PATCH 0/4] Add SCU device node support for Exynos4
From: Marek Szyprowski @ 2016-11-04 7:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478230764-13748-1-git-send-email-pankaj.dubey@samsung.com>
Hi Pankaj,
On 2016-11-04 04:39, Pankaj Dubey wrote:
> This patch series does some cleanup for Exynos4 SoC based boards.
> We are currently statically mapping SCU SFRs in mach-exynos/exynos.c
> which can be avoided and related dependencies can be removed by introduction
> of SCU device node.
>
> This patch series is tested on Exynos4210 based Origen board for SMP boot.
>
> Pankaj Dubey (4):
> ARM: EXYNOS: Remove smp_init_cpus hook from platsmp.c
> ARM: dts: exynos: Add SCU device node to exynos4.dtsi
> ARM: EXYNOS: Remove static mapping of SCU SFR
> ARM: EXYNOS: Remove unused soc_is_exynos{4,5}
>
> arch/arm/boot/dts/exynos4.dtsi | 5 +++
> arch/arm/mach-exynos/common.h | 5 ---
> arch/arm/mach-exynos/exynos.c | 22 -------------
> arch/arm/mach-exynos/include/mach/map.h | 2 --
> arch/arm/mach-exynos/platsmp.c | 49 +++++++---------------------
> arch/arm/mach-exynos/pm.c | 14 ++++++--
> arch/arm/mach-exynos/suspend.c | 15 ++++++---
> arch/arm/plat-samsung/include/plat/map-s5p.h | 4 ---
> 8 files changed, 38 insertions(+), 78 deletions(-)
Nice cleanup! Works fine on Exynos4412-based Odroid U3 (SMP boot and S2R).
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Best regards
--
Marek Szyprowski, PhD
Samsung R&D Institute Poland
^ permalink raw reply
* [PATCH 3/6] clk: rockchip: add clock controller for rk1108
From: Heiko Stuebner @ 2016-11-04 7:32 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478176713-12066-1-git-send-email-andy.yan@rock-chips.com>
Hi Andy,
Am Donnerstag, 3. November 2016, 20:38:33 CET schrieb Andy Yan:
> From: Shawn Lin <shawn.lin@rock-chips.com>
>
> Add the clock tree definition and driver for rk1108 SoC.
>
> Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
> Signed-off-by: Andy Yan <andy.yan@rock-chips.com>
> ---
>
> drivers/clk/rockchip/Makefile | 1 +
> drivers/clk/rockchip/clk-rk1108.c | 463
> +++++++++++++++++++++++++++++++++ drivers/clk/rockchip/clk.h |
> 14 +
> include/dt-bindings/clock/rk1108-cru.h | 308 ++++++++++++++++++++++
Please split the rk1108-cru.h addition into a separate patch, so that I can
put it into a shared branch for clock and dts branches.
Also it looks like you didn't provide a devicetree binding document (in a
separate patch).
Clock-tree looks mostly good, just some small things below
> 4 files changed, 786 insertions(+)
> create mode 100644 drivers/clk/rockchip/clk-rk1108.c
> create mode 100644 include/dt-bindings/clock/rk1108-cru.h
>
> diff --git a/drivers/clk/rockchip/Makefile b/drivers/clk/rockchip/Makefile
> index b5f2c8e..16e098c 100644
> --- a/drivers/clk/rockchip/Makefile
> +++ b/drivers/clk/rockchip/Makefile
> @@ -11,6 +11,7 @@ obj-y += clk-mmc-phase.o
> obj-y += clk-ddr.o
> obj-$(CONFIG_RESET_CONTROLLER) += softrst.o
>
> +obj-y += clk-rk1108.o
> obj-y += clk-rk3036.o
> obj-y += clk-rk3188.o
> obj-y += clk-rk3228.o
> diff --git a/drivers/clk/rockchip/clk-rk1108.c
> b/drivers/clk/rockchip/clk-rk1108.c new file mode 100644
> index 0000000..eafc623
> --- /dev/null
> +++ b/drivers/clk/rockchip/clk-rk1108.c
> @@ -0,0 +1,463 @@
> +/*
> + * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
> + * Author: Shawn Lin <shawn.lin@rock-chips.com>
> + * Andy Yan <andy.yan@rock-chips.com>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/clk-provider.h>
> +#include <linux/of.h>
> +#include <linux/of_address.h>
> +#include <linux/syscore_ops.h>
> +#include <dt-bindings/clock/rk1108-cru.h>
> +#include "clk.h"
> +
> +#define RK1108_GRF_SOC_STATUS0 0x480
> +
> +enum rk1108_plls {
> + apll, dpll, gpll,
> +};
> +
> +static struct rockchip_pll_rate_table rk1108_pll_rates[] = {
> + /* _mhz, _refdiv, _fbdiv, _postdiv1, _postdiv2, _dsmpd, _frac */
> + RK3036_PLL_RATE(1608000000, 1, 67, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1584000000, 1, 66, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1560000000, 1, 65, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1536000000, 1, 64, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1512000000, 1, 63, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1488000000, 1, 62, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1464000000, 1, 61, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1440000000, 1, 60, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1416000000, 1, 59, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1392000000, 1, 58, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1368000000, 1, 57, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1344000000, 1, 56, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1320000000, 1, 55, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1296000000, 1, 54, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1272000000, 1, 53, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1248000000, 1, 52, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1200000000, 1, 50, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1188000000, 2, 99, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1104000000, 1, 46, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1100000000, 12, 550, 1, 1, 1, 0),
> + RK3036_PLL_RATE(1008000000, 1, 84, 2, 1, 1, 0),
> + RK3036_PLL_RATE(1000000000, 6, 500, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 984000000, 1, 82, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 960000000, 1, 80, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 936000000, 1, 78, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 912000000, 1, 76, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 900000000, 4, 300, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 888000000, 1, 74, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 864000000, 1, 72, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 840000000, 1, 70, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 816000000, 1, 68, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 800000000, 6, 400, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 700000000, 6, 350, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 696000000, 1, 58, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 600000000, 1, 75, 3, 1, 1, 0),
> + RK3036_PLL_RATE( 594000000, 2, 99, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 504000000, 1, 63, 3, 1, 1, 0),
> + RK3036_PLL_RATE( 500000000, 6, 250, 2, 1, 1, 0),
> + RK3036_PLL_RATE( 408000000, 1, 68, 2, 2, 1, 0),
> + RK3036_PLL_RATE( 312000000, 1, 52, 2, 2, 1, 0),
> + RK3036_PLL_RATE( 216000000, 1, 72, 4, 2, 1, 0),
> + RK3036_PLL_RATE( 96000000, 1, 64, 4, 4, 1, 0),
> + { /* sentinel */ },
> +};
> +
> +
double empty line. There are a lot more in this file, so please remove all of
them. One line of space between blocks is enough :-) .
[...]
> diff --git a/include/dt-bindings/clock/rk1108-cru.h
> b/include/dt-bindings/clock/rk1108-cru.h new file mode 100644
> index 0000000..e731cc8
> --- /dev/null
> +++ b/include/dt-bindings/clock/rk1108-cru.h
> @@ -0,0 +1,308 @@
> +/*
> + * Copyright (c) 2016 Rockchip Electronics Co. Ltd.
> + * Author:
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License as published by
> + * the Free Software Foundation; either version 2 of the License, or
> + * (at your option) any later version.
> + *
> + * This program is distributed in the hope that it will be useful,
> + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#ifndef _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
> +#define _DT_BINDINGS_CLK_ROCKCHIP_RK1108_H
> +
> +/* pll id */
> +#define RK1108_APLL_ID 0
> +#define RK1108_DPLL_ID 1
> +#define RK1108_GPLL_ID 2
> +#define RK1108_ARMCLK 3
> +#define RK1108_END_PLL_ID 4
what is this supposed to do. Looks like it should go away.
> +
> +/* sclk gates (special clocks) */
> +#define SCLK_SPI0 65
> +#define SCLK_NANDC 67
> +#define SCLK_SDMMC 68
> +#define SCLK_SDIO 69
> +#define SCLK_EMMC 71
> +#define SCLK_UART0 72
> +#define SCLK_UART1 73
> +#define SCLK_UART2 74
> +#define SCLK_I2S0 75
> +#define SCLK_I2S1 76
> +#define SCLK_I2S2 77
> +#define SCLK_TIMER0 78
> +#define SCLK_TIMER1 79
> +#define SCLK_SFC 80
> +#define SCLK_SDMMC_DRV 81
> +#define SCLK_SDIO_DRV 82
> +#define SCLK_EMMC_DRV 83
> +#define SCLK_SDMMC_SAMPLE 84
> +#define SCLK_SDIO_SAMPLE 85
> +#define SCLK_EMMC_SAMPLE 86
> +
> +/* aclk gates */
> +#define ACLK_DMAC 251
> +#define ACLK_PRE 252
> +#define ACLK_CORE 253
> +#define ACLK_ENMCORE 254
> +
> +/* pclk gates */
> +#define PCLK_GPIO1 321
> +#define PCLK_GPIO2 322
> +#define PCLK_GPIO3 323
> +#define PCLK_GRF 329
> +#define PCLK_I2C1 333
> +#define PCLK_I2C2 334
> +#define PCLK_I2C3 335
> +#define PCLK_SPI 338
> +#define PCLK_SFC 339
> +#define PCLK_UART0 341
> +#define PCLK_UART1 342
> +#define PCLK_UART2 343
> +#define PCLK_TSADC 344
> +#define PCLK_PWM 350
> +#define PCLK_TIMER 353
> +#define PCLK_PERI 363
> +
> +/* hclk gates */
> +#define HCLK_I2S0_8CH 442
> +#define HCLK_I2S1_8CH 443
> +#define HCLK_I2S2_2CH 444
> +#define HCLK_NANDC 453
> +#define HCLK_SDMMC 456
> +#define HCLK_SDIO 457
> +#define HCLK_EMMC 459
> +#define HCLK_PERI 478
> +#define HCLK_SFC 479
> +
> +#define CLK_NR_CLKS (HCLK_SFC + 1)
> +
> +/* reset id */
> +#define SRST_CORE_PO_AD 0
> +#define SRST_CORE_AD 1
> +#define SRST_L2_AD 2
> +#define SRST_CPU_NIU_AD 3
> +#define SRST_CORE_PO 4
> +#define SRST_CORE 5
> +#define SRST_L2 6
> +#define RST_0RES7 7
> +#define SRST_CORE_DBG 8
> +#define PRST_DBG 9
> +#define RST_DAP 10
> +#define PRST_DBG_NIU 11
> +#define RST_0RES12 12
> +#define RST_0RES13 13
> +#define RST_0RES14 14
> +#define ARST_STRC_SYS_AD 15
> +
> +#define SRST_DDRPHY_CLKDIV 16
> +#define SRST_DDRPHY 17
> +#define PRST_DDRPHY 18
> +#define PRST_HDMIPHY 19
> +#define PRST_VDACPHY 20
> +#define PRST_VADCPHY 21
> +#define PRST_MIPI_CSI_PHY 22
> +#define PRST_MIPI_DSI_PHY 23
> +#define PRST_ACODEC 24
> +#define ARST_BUS_NIU 25
> +#define PRST_TOP_NIU 26
> +#define ARST_INTMEM 27
> +#define HRST_ROM 28
> +#define ARST_DMAC 29
> +#define SRST_MSCH_NIU 30
> +#define PRST_MSCH_NIU 31
> +
> +#define PRST_DDRUPCTL 32
> +#define NRST_DDRUPCTL 33
> +#define PRST_DDRMON 34
> +#define HRST_I2S0_8CH 35
> +#define MRST_I2S0_8CH 36
> +#define HRST_I2S1_2CH 37
> +#define MRST_IS21_2CH 38
> +#define HRST_I2S2_2CH 39
> +#define MRST_I2S2_2CH 40
> +#define HRST_CRYPTO 41
> +#define SRST_CRYPTO 42
> +#define PRST_SPI 43
> +#define SRST_SPI 44
> +#define PRST_UART0 45
> +#define PRST_UART1 46
> +#define PRST_UART2 47
> +
> +#define SRST_UART0 48
> +#define SRST_UART1 49
> +#define SRST_UART2 50
> +#define PRST_I2C1 51
> +#define PRST_I2C2 52
> +#define PRST_I2C3 53
> +#define SRST_I2C1 54
> +#define SRST_I2C2 55
> +#define SRST_I2C3 56
> +#define RST_3RES9 57
> +#define PRST_PWM1 58
> +#define RST_3RES11 59
> +#define SRST_PWM1 60
> +#define PRST_WDT 61
> +#define PRST_GPIO1 62
> +#define PRST_GPIO2 63
> +
> +#define PRST_GPIO3 64
> +#define PRST_GRF 65
> +#define PRST_EFUSE 66
> +#define PRST_EFUSE512 67
> +#define PRST_TIMER0 68
> +#define SRST_TIMER0 69
> +#define SRST_TIMER1 70
> +#define PRST_TSADC 71
> +#define SRST_TSADC 72
> +#define PRST_SARADC 73
> +#define SRST_SARADC 74
> +#define HRST_SYSBUS 75
> +#define PRST_USBGRF 76
> +#define RST_4RES13 77
> +#define RST_4RES14 78
> +#define RST_4RES15 79
> +
> +#define ARST_PERIPH_NIU 80
> +#define HRST_PERIPH_NIU 81
> +#define PRST_PERIPH_NIU 82
> +#define HRST_PERIPH 83
> +#define HRST_SDMMC 84
> +#define HRST_SDIO 85
> +#define HRST_EMMC 86
> +#define HRST_NANDC 87
> +#define NRST_NANDC 88
> +#define HRST_SFC 89
> +#define SRST_SFC 90
> +#define ARST_GMAC 91
> +#define HRST_OTG 92
> +#define SRST_OTG 93
> +#define SRST_OTG_ADP 94
> +#define HRST_HOST0 95
> +
> +#define HRST_HOST0_AUX 96
> +#define HRST_HOST0_ARB 97
> +#define SRST_HOST0_EHCIPHY 98
> +#define SRST_HOST0_UTMI 99
> +#define SRST_USBPOR 100
> +#define SRST_UTMI0 101
> +#define SRST_UTMI1 102
> +#define RST_6RES7 103
> +#define RST_6RES8 104
> +#define RST_6RES9 105
> +#define RST_6RES10 106
> +#define RST_6RES11 107
> +#define RST_6RES12 108
> +#define RST_6RES13 109
> +#define RST_6RES14 110
> +#define RST_6RES15 101
> +
> +#define ARST_VIO0_NIU 102
> +#define ARST_VIO1_NIU 103
> +#define HRST_VIO_NIU 104
> +#define PRST_VIO_NIU 105
> +#define ARST_VOP 106
> +#define HRST_VOP 107
> +#define DRST_VOP 108
> +#define ARST_IEP 109
> +#define HRST_IEP 110
> +#define ARST_RGA 111
> +#define HRST_RGA 112
> +#define SRST_RGA 113
> +#define PRST_CVBS 114
> +#define PRST_HDMI 115
> +#define SRST_HDMI 116
> +#define PRST_MIPI_DSI 117
> +
> +#define ARST_ISP_NIU 118
> +#define HRST_ISP_NIU 119
> +#define HRST_ISP 120
> +#define SRST_ISP 121
> +#define ARST_VIP0 122
> +#define HRST_VIP0 123
> +#define PRST_VIP0 124
> +#define ARST_VIP1 125
> +#define HRST_VIP1 126
> +#define PRST_VIP1 127
> +#define ARST_VIP2 128
> +#define HRST_VIP2 129
> +#define PRST_VIP2 120
> +#define ARST_VIP3 121
> +#define HRST_VIP3 122
> +#define PRST_VIP4 123
> +
> +#define PRST_CIF1TO4 124
> +#define SRST_CVBS_CLK 125
> +#define HRST_CVBS 126
> +#define RST_9RES3 127
> +#define RST_9RES4 128
> +#define RST_9RES5 129
> +#define RST_9RES6 130
> +#define RST_9RES7 131
> +#define RST_9RES8 132
> +#define RST_9RES9 133
> +#define RST_9RES10 134
> +#define RST_9RES11 134
> +#define RST_9RES12 136
> +#define RST_9RES13 137
> +#define RST_9RES14 138
> +#define RST_9RES15 139
there is no need to document unused/reserved bits in the header,
so please drop all of them (more in the areas above here as well).
Heiko
^ permalink raw reply
* [PATCH v2 2/2] power: bq27xxx_battery: add poll interval property query
From: Pavel Machek @ 2016-11-04 7:09 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAKzfze8d_MZJzR1a6rbwVXCWhb30C5GqFamUt2Viw1CzvyaQxw@mail.gmail.com>
On Thu 2016-11-03 22:00:56, Matt Ranostay wrote:
> On Wed, Nov 2, 2016 at 1:22 AM, Pavel Machek <pavel@ucw.cz> wrote:
> > Hi!
> >
> >> >> >> Better then previous one.
> >> >> >>
> >> >> >> But my version of bq27xxx_battery.c already contains this:
> >> >> >
> >> >> > This is for allowing udev rule to set the properties as well.
> >> >> > otherwise a kinda crude RUN = " echo value >
> >> >> > /sys/module/bq27xxx_battery/parameters/poll_interval" is required.
> >> >>
> >> >> Any thoughts on this?
> >> >
> >> > I'd say echo value >
> >> > /sys/module/bq27xxx_battery/parameters/poll_interval .. is quite
> >> > adequate solution...?
> >> >
> >> > Alternatively, convince us that something else is useful for everyone,
> >> > and we can do the right thing (poll more often when battery is nearly
> >> > empty), automatically...
> >>
> >> Ok should have had the patchset set it per device, and not use the
> >> global poll_interval. Of need to add some logic to see if uses the
> >> global poll_interval or it's own setting.
> >>
> >> There are times where you could have multiple batteries connected to
> >> multiple fuel gauges, and want to up the polling interval on certain
> >> ones that are discharging at different rates.
> >>
> >> But of course I'll let you guys let me know if this seems useful at all.
> >
> > I agree per-device polling would be cleaner.
> >
>
> Ok I'll work something up for RFC.
>
> > But unless you have hardware with more than one bq27xxx, I'd avoid the
> > work...
> >
> > Now... its also possible that poll_interval should change itself
> > (within kernel) to do the right thing.
> >
>
> True but that is state machine territory, but I'll worry about that later...
Do you actually have hardware with more than one bq27xxx?
Best regards,
Pavel
--
(english) http://www.livejournal.com/~pavelmachek
(cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 181 bytes
Desc: Digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161104/b2f18794/attachment.sig>
^ permalink raw reply
* [PATCH v6 6/7] net: ethernet: bgmac: add NS2 support
From: Rafał Miłecki @ 2016-11-04 7:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-7-git-send-email-jon.mason@broadcom.com>
On 2016-11-04 06:11, Jon Mason wrote:
> Add support for the variant of amac hardware present in the Broadcom
> Northstar2 based SoCs. Northstar2 requires an additional register to
> be
> configured with the port speed/duplexity (NICPM). This can be added to
> the link callback to hide it from the instances that do not use this.
> Also, clearing of the pending interrupts on init is required due to
> observed issues on some platforms.
>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
[Resending from Roundcube due to "Wrong MIME labeling on 8-bit character
texts."
vger.kernel.org reject when using Thunderbird]
Checked for possible regressions on Northstar, looks OK.
Acked-by: Rafa? Mi?ecki <rafal@milecki.pl>
^ permalink raw reply
* [PATCH v6 5/7] net: ethernet: bgmac: device tree phy enablement
From: Rafał Miłecki @ 2016-11-04 7:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-6-git-send-email-jon.mason@broadcom.com>
On 2016-11-04 06:11, Jon Mason wrote:
> Change the bgmac driver to allow for phy's defined by the device tree
>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
[Resending from Roundcube due to "Wrong MIME labeling on 8-bit character
texts."
vger.kernel.org reject when using Thunderbird]
Checked for possible regressions on Northstar, looks OK.
Acked-by: Rafa? Mi?ecki <rafal@milecki.pl>
^ permalink raw reply
* [PATCH v6 6/7] net: ethernet: bgmac: add NS2 support
From: Rafal Milecki @ 2016-11-04 6:48 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-7-git-send-email-jon.mason@broadcom.com>
On 11/04/2016 06:11 AM, Jon Mason wrote:
> Add support for the variant of amac hardware present in the Broadcom
> Northstar2 based SoCs. Northstar2 requires an additional register to be
> configured with the port speed/duplexity (NICPM). This can be added to
> the link callback to hide it from the instances that do not use this.
> Also, clearing of the pending interrupts on init is required due to
> observed issues on some platforms.
>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Checked for possible regressions on Northstar, looks OK.
Acked-by: Rafa? Mi?ecki <rafal@milecki.pl>
^ permalink raw reply
* [PATCH v6 5/7] net: ethernet: bgmac: device tree phy enablement
From: Rafal Milecki @ 2016-11-04 6:43 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-6-git-send-email-jon.mason@broadcom.com>
On 11/04/2016 06:11 AM, Jon Mason wrote:
> Change the bgmac driver to allow for phy's defined by the device tree
>
> Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Checked for possible regressions on Northstar, looks OK.
Acked-by: Rafa? Mi?ecki <rafal@milecki.pl>
^ permalink raw reply
* [PATCH v3] clk: mediatek: Allow changing PLL rate when it is off
From: James Liao @ 2016-11-04 6:42 UTC (permalink / raw)
To: linux-arm-kernel
Some modules may need to change its clock rate before turn on it.
So changing PLL's rate when it is off should be allowed.
This patch removes PLL enabled check before set rate, so that
PLLs can set new frequency even if they are off.
On MT8173 for example, ARMPLL's enable bit can be controlled by
other HW. That means ARMPLL may be turned on even if we (CPU / SW)
set ARMPLL's enable bit as 0. In this case, SW may want and can
still change ARMPLL's rate by changing its pcw and postdiv settings.
But without this patch, new pcw setting will not be applied because
its enable bit is 0.
Signed-off-by: James Liao <jamesjj.liao@mediatek.com>
Acked-by: Michael Turquette <mturuqette@baylibre.com>
---
Please refer to previous comments in [1] and [2].
changes since v2:
- Rebase to v4.9-rc1.
changes since v1:
- Add more explanation in commit messages.
[1] https://patchwork.kernel.org/patch/7983221/
[2] https://patchwork.kernel.org/patch/7998891/
drivers/clk/mediatek/clk-pll.c | 9 ++-------
1 file changed, 2 insertions(+), 7 deletions(-)
diff --git a/drivers/clk/mediatek/clk-pll.c b/drivers/clk/mediatek/clk-pll.c
index 0c2deac..80f57b4 100644
--- a/drivers/clk/mediatek/clk-pll.c
+++ b/drivers/clk/mediatek/clk-pll.c
@@ -91,9 +91,6 @@ static void mtk_pll_set_rate_regs(struct mtk_clk_pll *pll, u32 pcw,
int postdiv)
{
u32 con1, val;
- int pll_en;
-
- pll_en = readl(pll->base_addr + REG_CON0) & CON0_BASE_EN;
/* set postdiv */
val = readl(pll->pd_addr);
@@ -114,15 +111,13 @@ static void mtk_pll_set_rate_regs(struct mtk_clk_pll *pll, u32 pcw,
con1 = readl(pll->base_addr + REG_CON1);
- if (pll_en)
- con1 |= CON0_PCW_CHG;
+ con1 |= CON0_PCW_CHG;
writel(con1, pll->base_addr + REG_CON1);
if (pll->tuner_addr)
writel(con1 + 1, pll->tuner_addr);
- if (pll_en)
- udelay(20);
+ udelay(20);
}
/*
--
1.9.1
^ permalink raw reply related
* [GIT PULL 4/4] DaVinci defconfig updates for v4.10
From: Sekhar Nori @ 2016-11-04 6:25 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161104062535.9593-1-nsekhar@ti.com>
The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci.git tags/davinci-for-v4.10/defconfig
for you to fetch changes up to 6e9be8608771192851a3adf59f0ba9240e3f802c:
ARM: davinci_all_defconfig: enable LED default-on trigger (2016-11-01 11:42:54 +0530)
----------------------------------------------------------------
Some updates to davinci_all_defconfig for MMC,
LCDC and GPIO/LEDs.
----------------------------------------------------------------
Bartosz Golaszewski (1):
ARM: davinci_all_defconfig: enable LCDC DRM driver
David Lechner (3):
ARM: davinci_all_defconfig: enable gpio poweroff driver
ARM: davinci_all_defconfig: build MMC into kernel
ARM: davinci_all_defconfig: enable LED default-on trigger
arch/arm/configs/davinci_all_defconfig | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
^ permalink raw reply
* [GIT PULL 3/4] DaVinci device-tree updates for v4.10
From: Sekhar Nori @ 2016-11-04 6:25 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161104062535.9593-1-nsekhar@ti.com>
The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci.git tags/davinci-for-v4.10/dt
for you to fetch changes up to 1b499f255589204466d8f8ab26e6b577d7b5c88f:
ARM: dts: da850: Add cfgchip syscon node (2016-11-01 15:11:10 +0530)
----------------------------------------------------------------
DaVinci device-tree source additions for
LCD, SPI and cfgchip syscon.
----------------------------------------------------------------
David Lechner (2):
ARM: dts: da850: Add DMA to SPI0
ARM: dts: da850: Add cfgchip syscon node
Karl Beldan (1):
ARM: dts: da850: add a node for the LCD controller
arch/arm/boot/dts/da850.dtsi | 40 ++++++++++++++++++++++++++++++++++++++++
1 file changed, 40 insertions(+)
^ permalink raw reply
* [GIT PULL 2/4] DaVinci SoC updates for v4.10
From: Sekhar Nori @ 2016-11-04 6:25 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161104062535.9593-1-nsekhar@ti.com>
The following changes since commit 766763dbdc1dca11deabdb00077a1c19e2803f0a:
ARM: davinci: da8xx: Remove duplicated defines (2016-10-31 16:51:56 +0530)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci.git tags/davinci-for-v4.10/soc
for you to fetch changes up to ced95ac0815501f47a6041548d70d8900400912d:
ARM: davinci: da8xx: register USB PHY clocks in the DT file (2016-11-01 15:24:24 +0530)
----------------------------------------------------------------
DaVinci SoC support improvements mainly towards an effort to
get to working USB support.
- use CFGCHIP syscon device to access common registers
- define platform data and device tree nodes for newly
introduced USB phy driver
- clock lookup and auxdata lookup for USB phy and also
for LCDC (LCD controller)
----------------------------------------------------------------
Axel Haslam (2):
ARM: davinci: da8xx: Add full regulator constraints for non-DT boot
ARM: davinci: da8xx: register USB PHY clocks in the DT file
David Lechner (5):
ARM: davinci: da8xx: Add CFGCHIP syscon platform device
ARM: davinci: da8xx: Add USB PHY platform device
ARM: davinci: da8xx: Add USB device names to clock lookup tables
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for USB phy
ARM: davinci: da8xx: add usb phy clocks
Karl Beldan (1):
ARM: davinci: da8xx-dt: add OF_DEV_AUXDATA entry for lcdc
arch/arm/mach-davinci/board-da830-evm.c | 55 +++---
arch/arm/mach-davinci/board-da850-evm.c | 4 +
arch/arm/mach-davinci/board-mityomapl138.c | 4 +
arch/arm/mach-davinci/board-omapl138-hawk.c | 27 ++-
arch/arm/mach-davinci/da830.c | 4 +-
arch/arm/mach-davinci/da850.c | 4 +-
arch/arm/mach-davinci/da8xx-dt.c | 15 ++
arch/arm/mach-davinci/devices-da8xx.c | 28 +++
arch/arm/mach-davinci/include/mach/da8xx.h | 6 +
arch/arm/mach-davinci/usb-da8xx.c | 276 ++++++++++++++++++++++++++--
10 files changed, 366 insertions(+), 57 deletions(-)
^ permalink raw reply
* [GIT PULL 1/4] DaVinci cleanup for v4.10
From: Sekhar Nori @ 2016-11-04 6:25 UTC (permalink / raw)
To: linux-arm-kernel
The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci.git tags/davinci-for-v4.10/cleanup
for you to fetch changes up to 766763dbdc1dca11deabdb00077a1c19e2803f0a:
ARM: davinci: da8xx: Remove duplicated defines (2016-10-31 16:51:56 +0530)
----------------------------------------------------------------
Clean-up some unnecessary code from mach-davinci.
- Remove now unneeded dma resources where drivers
are already converted to use the dma_slave_map[]
structure.
- Remove some duplicated defines related to USB support.
----------------------------------------------------------------
Alexandre Bailon (1):
ARM: davinci: da8xx: Remove duplicated defines
Peter Ujfalusi (4):
ARM: davinci: devices-da8xx: Remove DMA resources for MMC and SPI
ARM: davinci: devices: Remove DMA resources for MMC
ARM: davinci: dm355: Remove DMA resources for SPI
ARM: davinci: dm365: Remove DMA resources for SPI
arch/arm/mach-davinci/board-da830-evm.c | 5 +++--
arch/arm/mach-davinci/board-omapl138-hawk.c | 3 ++-
arch/arm/mach-davinci/devices-da8xx.c | 29 -----------------------------
arch/arm/mach-davinci/devices.c | 3 ---
arch/arm/mach-davinci/dm355.c | 8 --------
arch/arm/mach-davinci/dm365.c | 8 --------
include/linux/platform_data/usb-davinci.h | 23 -----------------------
7 files changed, 5 insertions(+), 74 deletions(-)
^ permalink raw reply
* [PATCH] drm/sun4i: Propagate error to the caller
From: Christophe JAILLET @ 2016-11-04 6:13 UTC (permalink / raw)
To: linux-arm-kernel
If 'sun4i_layers_init()' returns an error, propagate it instead of
returning -EINVAL unconditionally.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
---
drivers/gpu/drm/sun4i/sun4i_drv.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/sun4i/sun4i_drv.c b/drivers/gpu/drm/sun4i/sun4i_drv.c
index 628712e6edd6..ee4e5f987b6f 100644
--- a/drivers/gpu/drm/sun4i/sun4i_drv.c
+++ b/drivers/gpu/drm/sun4i/sun4i_drv.c
@@ -145,7 +145,7 @@ static int sun4i_drv_bind(struct device *dev)
drv->layers = sun4i_layers_init(drm);
if (IS_ERR(drv->layers)) {
dev_err(drm->dev, "Couldn't create the planes\n");
- ret = -EINVAL;
+ ret = PTR_ERR(drv->layers);
goto free_drm;
}
--
2.9.3
^ permalink raw reply related
* [PATCH 2/3] phy: da8xx-usb: rename the ohci device to ohci-da8xx
From: Sekhar Nori @ 2016-11-04 5:34 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <fd6b848d-9740-70ef-6850-7f6a64e66bfb@ti.com>
Hi Kishon,
On Thursday 03 November 2016 10:20 PM, Kishon Vijay Abraham I wrote:
>
>
> On Wednesday 02 November 2016 06:14 PM, Axel Haslam wrote:
>> There is only one ohci on the da8xx series of chips,
>> so remove the ".0" when creating the phy. Also add
>> the "-da8xx" postfix to be consistent across davinci
>> usb drivers.
>>
>> Signed-off-by: Axel Haslam <ahaslam@baylibre.com>
>
> Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
You will have to carry this patch from your tree. I thought I can carry
the entire series, but the USB patch depends on other patches that Greg
has already queued. So I think its best if the individual patches go
through their respective trees.
Note that there is a v2 already submitted.
Thanks,
Sekhar
^ permalink raw reply
* [PATCH v6 7/7] arm64: dts: NS2: add AMAC ethernet support
From: Jon Mason @ 2016-11-04 5:11 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
Add support for the AMAC ethernet to the Broadcom Northstar2 SoC device
tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
arch/arm64/boot/dts/broadcom/ns2-svk.dts | 5 +++++
arch/arm64/boot/dts/broadcom/ns2.dtsi | 12 ++++++++++++
2 files changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/broadcom/ns2-svk.dts b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
index b09f3bc..c4d5442 100644
--- a/arch/arm64/boot/dts/broadcom/ns2-svk.dts
+++ b/arch/arm64/boot/dts/broadcom/ns2-svk.dts
@@ -56,6 +56,10 @@
};
};
+&enet {
+ status = "ok";
+};
+
&pci_phy0 {
status = "ok";
};
@@ -174,6 +178,7 @@
&mdio_mux_iproc {
mdio at 10 {
gphy0: eth-phy at 10 {
+ enet-phy-lane-swap;
reg = <0x10>;
};
};
diff --git a/arch/arm64/boot/dts/broadcom/ns2.dtsi b/arch/arm64/boot/dts/broadcom/ns2.dtsi
index d95dc40..773ed59 100644
--- a/arch/arm64/boot/dts/broadcom/ns2.dtsi
+++ b/arch/arm64/boot/dts/broadcom/ns2.dtsi
@@ -191,6 +191,18 @@
#include "ns2-clock.dtsi"
+ enet: ethernet at 61000000 {
+ compatible = "brcm,ns2-amac";
+ reg = <0x61000000 0x1000>,
+ <0x61090000 0x1000>,
+ <0x61030000 0x100>;
+ reg-names = "amac_base", "idm_base", "nicpm_base";
+ interrupts = <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
+ phy-handle = <&gphy0>;
+ phy-mode = "rgmii";
+ status = "disabled";
+ };
+
dma0: dma at 61360000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x61360000 0x1000>;
--
2.7.4
^ permalink raw reply related
* [PATCH v6 6/7] net: ethernet: bgmac: add NS2 support
From: Jon Mason @ 2016-11-04 5:11 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
Add support for the variant of amac hardware present in the Broadcom
Northstar2 based SoCs. Northstar2 requires an additional register to be
configured with the port speed/duplexity (NICPM). This can be added to
the link callback to hide it from the instances that do not use this.
Also, clearing of the pending interrupts on init is required due to
observed issues on some platforms.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/ethernet/broadcom/bgmac-platform.c | 56 +++++++++++++++++++++++++-
drivers/net/ethernet/broadcom/bgmac.c | 3 ++
drivers/net/ethernet/broadcom/bgmac.h | 1 +
3 files changed, 58 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index 4642940..6f736c1 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -14,12 +14,21 @@
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/bcma/bcma.h>
+#include <linux/brcmphy.h>
#include <linux/etherdevice.h>
#include <linux/of_address.h>
#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include "bgmac.h"
+#define NICPM_IOMUX_CTRL 0x00000008
+
+#define NICPM_IOMUX_CTRL_INIT_VAL 0x3196e000
+#define NICPM_IOMUX_CTRL_SPD_SHIFT 10
+#define NICPM_IOMUX_CTRL_SPD_10M 0
+#define NICPM_IOMUX_CTRL_SPD_100M 1
+#define NICPM_IOMUX_CTRL_SPD_1000M 2
+
static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
{
return readl(bgmac->plat.base + offset);
@@ -87,12 +96,46 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
WARN_ON(1);
}
+static void bgmac_nicpm_speed_set(struct net_device *net_dev)
+{
+ struct bgmac *bgmac = netdev_priv(net_dev);
+ u32 val;
+
+ if (!bgmac->plat.nicpm_base)
+ return;
+
+ val = NICPM_IOMUX_CTRL_INIT_VAL;
+ switch (bgmac->net_dev->phydev->speed) {
+ default:
+ netdev_err(net_dev, "Unsupported speed. Defaulting to 1000Mb\n");
+ case SPEED_1000:
+ val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+ break;
+ case SPEED_100:
+ val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+ break;
+ case SPEED_10:
+ val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
+ break;
+ }
+
+ writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
+
+ bgmac_adjust_link(bgmac->net_dev);
+}
+
static int platform_phy_connect(struct bgmac *bgmac)
{
struct phy_device *phy_dev;
- phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
- bgmac_adjust_link);
+ if (bgmac->plat.nicpm_base)
+ phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+ bgmac->dev->of_node,
+ bgmac_nicpm_speed_set);
+ else
+ phy_dev = of_phy_get_and_connect(bgmac->net_dev,
+ bgmac->dev->of_node,
+ bgmac_adjust_link);
if (!phy_dev) {
dev_err(bgmac->dev, "PHY connection failed\n");
return -ENODEV;
@@ -156,6 +199,14 @@ static int bgmac_probe(struct platform_device *pdev)
if (IS_ERR(bgmac->plat.idm_base))
return PTR_ERR(bgmac->plat.idm_base);
+ regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
+ if (regs) {
+ bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
+ regs);
+ if (IS_ERR(bgmac->plat.nicpm_base))
+ return PTR_ERR(bgmac->plat.nicpm_base);
+ }
+
bgmac->read = platform_bgmac_read;
bgmac->write = platform_bgmac_write;
bgmac->idm_read = platform_bgmac_idm_read;
@@ -187,6 +238,7 @@ static int bgmac_remove(struct platform_device *pdev)
static const struct of_device_id bgmac_of_enet_match[] = {
{.compatible = "brcm,amac",},
{.compatible = "brcm,nsp-amac",},
+ {.compatible = "brcm,ns2-amac",},
{},
};
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 7f66ea7..a29787f 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
static void bgmac_chip_init(struct bgmac *bgmac)
{
+ /* Clear any erroneously pending interrupts */
+ bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
+
/* 1 interrupt per received frame */
bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index bfd9f40..71f493f 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -463,6 +463,7 @@ struct bgmac {
struct {
void *base;
void *idm_base;
+ void *nicpm_base;
} plat;
struct {
struct bcma_device *core;
--
2.7.4
^ permalink raw reply related
* [PATCH v6 5/7] net: ethernet: bgmac: device tree phy enablement
From: Jon Mason @ 2016-11-04 5:11 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
Change the bgmac driver to allow for phy's defined by the device tree
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
---
drivers/net/ethernet/broadcom/bgmac-bcma.c | 22 +++++++++++++++++++
drivers/net/ethernet/broadcom/bgmac-platform.c | 22 ++++++++++++++++++-
drivers/net/ethernet/broadcom/bgmac.c | 29 +++++---------------------
drivers/net/ethernet/broadcom/bgmac.h | 8 +++++++
4 files changed, 56 insertions(+), 25 deletions(-)
diff --git a/drivers/net/ethernet/broadcom/bgmac-bcma.c b/drivers/net/ethernet/broadcom/bgmac-bcma.c
index c16ec3a..4a4ffc0 100644
--- a/drivers/net/ethernet/broadcom/bgmac-bcma.c
+++ b/drivers/net/ethernet/broadcom/bgmac-bcma.c
@@ -80,6 +80,24 @@ static void bcma_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset, u32 mask,
bcma_maskset32(bgmac->bcma.cmn, offset, mask, set);
}
+static int bcma_phy_connect(struct bgmac *bgmac)
+{
+ struct phy_device *phy_dev;
+ char bus_id[MII_BUS_ID_SIZE + 3];
+
+ /* Connect to the PHY */
+ snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
+ bgmac->phyaddr);
+ phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link,
+ PHY_INTERFACE_MODE_MII);
+ if (IS_ERR(phy_dev)) {
+ dev_err(bgmac->dev, "PHY connection failed\n");
+ return PTR_ERR(phy_dev);
+ }
+
+ return 0;
+}
+
static const struct bcma_device_id bgmac_bcma_tbl[] = {
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_4706_MAC_GBIT,
BCMA_ANY_REV, BCMA_ANY_CLASS),
@@ -275,6 +293,10 @@ static int bgmac_probe(struct bcma_device *core)
bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset;
bgmac->get_bus_clock = bcma_bgmac_get_bus_clock;
bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32;
+ if (bgmac->mii_bus)
+ bgmac->phy_connect = bcma_phy_connect;
+ else
+ bgmac->phy_connect = bgmac_phy_connect_direct;
err = bgmac_enet_probe(bgmac);
if (err)
diff --git a/drivers/net/ethernet/broadcom/bgmac-platform.c b/drivers/net/ethernet/broadcom/bgmac-platform.c
index be52f27..4642940 100644
--- a/drivers/net/ethernet/broadcom/bgmac-platform.c
+++ b/drivers/net/ethernet/broadcom/bgmac-platform.c
@@ -16,6 +16,7 @@
#include <linux/bcma/bcma.h>
#include <linux/etherdevice.h>
#include <linux/of_address.h>
+#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include "bgmac.h"
@@ -86,6 +87,20 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
WARN_ON(1);
}
+static int platform_phy_connect(struct bgmac *bgmac)
+{
+ struct phy_device *phy_dev;
+
+ phy_dev = of_phy_get_and_connect(bgmac->net_dev, bgmac->dev->of_node,
+ bgmac_adjust_link);
+ if (!phy_dev) {
+ dev_err(bgmac->dev, "PHY connection failed\n");
+ return -ENODEV;
+ }
+
+ return 0;
+}
+
static int bgmac_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
@@ -102,7 +117,6 @@ static int bgmac_probe(struct platform_device *pdev)
/* Set the features of the 4707 family */
bgmac->feature_flags |= BGMAC_FEAT_CLKCTLST;
bgmac->feature_flags |= BGMAC_FEAT_NO_RESET;
- bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
bgmac->feature_flags |= BGMAC_FEAT_CMDCFG_SR_REV4;
bgmac->feature_flags |= BGMAC_FEAT_TX_MASK_SETUP;
bgmac->feature_flags |= BGMAC_FEAT_RX_MASK_SETUP;
@@ -151,6 +165,12 @@ static int bgmac_probe(struct platform_device *pdev)
bgmac->cco_ctl_maskset = platform_bgmac_cco_ctl_maskset;
bgmac->get_bus_clock = platform_bgmac_get_bus_clock;
bgmac->cmn_maskset32 = platform_bgmac_cmn_maskset32;
+ if (of_parse_phandle(np, "phy-handle", 0)) {
+ bgmac->phy_connect = platform_phy_connect;
+ } else {
+ bgmac->phy_connect = bgmac_phy_connect_direct;
+ bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
+ }
return bgmac_enet_probe(bgmac);
}
diff --git a/drivers/net/ethernet/broadcom/bgmac.c b/drivers/net/ethernet/broadcom/bgmac.c
index 31ca204..7f66ea7 100644
--- a/drivers/net/ethernet/broadcom/bgmac.c
+++ b/drivers/net/ethernet/broadcom/bgmac.c
@@ -1388,7 +1388,7 @@ static const struct ethtool_ops bgmac_ethtool_ops = {
* MII
**************************************************/
-static void bgmac_adjust_link(struct net_device *net_dev)
+void bgmac_adjust_link(struct net_device *net_dev)
{
struct bgmac *bgmac = netdev_priv(net_dev);
struct phy_device *phy_dev = net_dev->phydev;
@@ -1411,8 +1411,9 @@ static void bgmac_adjust_link(struct net_device *net_dev)
phy_print_status(phy_dev);
}
}
+EXPORT_SYMBOL_GPL(bgmac_adjust_link);
-static int bgmac_phy_connect_direct(struct bgmac *bgmac)
+int bgmac_phy_connect_direct(struct bgmac *bgmac)
{
struct fixed_phy_status fphy_status = {
.link = 1,
@@ -1437,24 +1438,7 @@ static int bgmac_phy_connect_direct(struct bgmac *bgmac)
return err;
}
-
-static int bgmac_phy_connect(struct bgmac *bgmac)
-{
- struct phy_device *phy_dev;
- char bus_id[MII_BUS_ID_SIZE + 3];
-
- /* Connect to the PHY */
- snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
- bgmac->phyaddr);
- phy_dev = phy_connect(bgmac->net_dev, bus_id, &bgmac_adjust_link,
- PHY_INTERFACE_MODE_MII);
- if (IS_ERR(phy_dev)) {
- dev_err(bgmac->dev, "PHY connection failed\n");
- return PTR_ERR(phy_dev);
- }
-
- return 0;
-}
+EXPORT_SYMBOL_GPL(bgmac_phy_connect_direct);
int bgmac_enet_probe(struct bgmac *info)
{
@@ -1507,10 +1491,7 @@ int bgmac_enet_probe(struct bgmac *info)
netif_napi_add(net_dev, &bgmac->napi, bgmac_poll, BGMAC_WEIGHT);
- if (!bgmac->mii_bus)
- err = bgmac_phy_connect_direct(bgmac);
- else
- err = bgmac_phy_connect(bgmac);
+ err = bgmac_phy_connect(bgmac);
if (err) {
dev_err(bgmac->dev, "Cannot connect to phy\n");
goto err_dma_free;
diff --git a/drivers/net/ethernet/broadcom/bgmac.h b/drivers/net/ethernet/broadcom/bgmac.h
index 80836b4..bfd9f40 100644
--- a/drivers/net/ethernet/broadcom/bgmac.h
+++ b/drivers/net/ethernet/broadcom/bgmac.h
@@ -513,10 +513,13 @@ struct bgmac {
u32 (*get_bus_clock)(struct bgmac *bgmac);
void (*cmn_maskset32)(struct bgmac *bgmac, u16 offset, u32 mask,
u32 set);
+ int (*phy_connect)(struct bgmac *bgmac);
};
int bgmac_enet_probe(struct bgmac *info);
void bgmac_enet_remove(struct bgmac *bgmac);
+void bgmac_adjust_link(struct net_device *net_dev);
+int bgmac_phy_connect_direct(struct bgmac *bgmac);
struct mii_bus *bcma_mdio_mii_register(struct bcma_device *core, u8 phyaddr);
void bcma_mdio_mii_unregister(struct mii_bus *mii_bus);
@@ -583,4 +586,9 @@ static inline void bgmac_set(struct bgmac *bgmac, u16 offset, u32 set)
{
bgmac_maskset(bgmac, offset, ~0, set);
}
+
+static inline int bgmac_phy_connect(struct bgmac *bgmac)
+{
+ return bgmac->phy_connect(bgmac);
+}
#endif /* _BGMAC_H */
--
2.7.4
^ permalink raw reply related
* [PATCH v6 4/7] Documentation: devicetree: net: add NS2 bindings to amac
From: Jon Mason @ 2016-11-04 5:10 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
Clean-up the documentation to the bgmac-amac driver, per suggestion by
Rob Herring, and add details for NS2 support.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
Documentation/devicetree/bindings/net/brcm,amac.txt | 16 +++++++++++-----
1 file changed, 11 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/brcm,amac.txt b/Documentation/devicetree/bindings/net/brcm,amac.txt
index ba5ecc1..2fefa1a 100644
--- a/Documentation/devicetree/bindings/net/brcm,amac.txt
+++ b/Documentation/devicetree/bindings/net/brcm,amac.txt
@@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings
-------------------------------------------------------------
Required properties:
- - compatible: "brcm,amac" or "brcm,nsp-amac"
- - reg: Address and length of the GMAC registers,
- Address and length of the GMAC IDM registers
- - reg-names: Names of the registers. Must have both "amac_base" and
- "idm_base"
+ - compatible: "brcm,amac"
+ "brcm,nsp-amac"
+ "brcm,ns2-amac"
+ - reg: Address and length of the register set for the device. It
+ contains the information of registers in the same order as
+ described by reg-names
+ - reg-names: Names of the registers.
+ "amac_base": Address and length of the GMAC registers
+ "idm_base": Address and length of the GMAC IDM registers
+ "nicpm_base": Address and length of the NIC Port Manager
+ registers (required for Northstar2)
- interrupts: Interrupt number
Optional properties:
--
2.7.4
^ permalink raw reply related
* [PATCH v6 3/7] net: phy: broadcom: Add BCM54810 PHY entry
From: Jon Mason @ 2016-11-04 5:10 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
The BCM54810 PHY requires some semi-unique configuration, which results
in some additional configuration in addition to the standard config.
Also, some users of the BCM54810 require the PHY lanes to be swapped.
Since there is no way to detect this, add a device tree query to see if
it is applicable.
Inspired-by: Vikas Soni <vsoni@broadcom.com>
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/phy/Kconfig | 2 +-
drivers/net/phy/broadcom.c | 58 +++++++++++++++++++++++++++++++++++++++++++++-
include/linux/brcmphy.h | 9 +++++++
3 files changed, 67 insertions(+), 2 deletions(-)
diff --git a/drivers/net/phy/Kconfig b/drivers/net/phy/Kconfig
index ff31c10..d3fcfd2 100644
--- a/drivers/net/phy/Kconfig
+++ b/drivers/net/phy/Kconfig
@@ -217,7 +217,7 @@ config BROADCOM_PHY
select BCM_NET_PHYLIB
---help---
Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
- BCM5481 and BCM5482 PHYs.
+ BCM5481, BCM54810 and BCM5482 PHYs.
config CICADA_PHY
tristate "Cicada PHYs"
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 3a64b3d..b1e32e9 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -18,7 +18,7 @@
#include <linux/module.h>
#include <linux/phy.h>
#include <linux/brcmphy.h>
-
+#include <linux/of.h>
#define BRCM_PHY_MODEL(phydev) \
((phydev)->drv->phy_id & (phydev)->drv->phy_id_mask)
@@ -45,6 +45,34 @@ static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
}
+static int bcm54810_config(struct phy_device *phydev)
+{
+ int rc, val;
+
+ val = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
+ val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
+ rc = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
+ val);
+ if (rc < 0)
+ return rc;
+
+ val = bcm54xx_auxctl_read(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
+ val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
+ val |= MII_BCM54XX_AUXCTL_MISC_WREN;
+ rc = bcm54xx_auxctl_write(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC,
+ val);
+ if (rc < 0)
+ return rc;
+
+ val = bcm_phy_read_shadow(phydev, BCM54810_SHD_CLK_CTL);
+ val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
+ rc = bcm_phy_write_shadow(phydev, BCM54810_SHD_CLK_CTL, val);
+ if (rc < 0)
+ return rc;
+
+ return 0;
+}
+
/* Needs SMDSP clock enabled via bcm54xx_phydsp_config() */
static int bcm50610_a0_workaround(struct phy_device *phydev)
{
@@ -217,6 +245,12 @@ static int bcm54xx_config_init(struct phy_device *phydev)
(phydev->dev_flags & PHY_BRCM_AUTO_PWRDWN_ENABLE))
bcm54xx_adjust_rxrefclk(phydev);
+ if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54810) {
+ err = bcm54810_config(phydev);
+ if (err)
+ return err;
+ }
+
bcm54xx_phydsp_config(phydev);
return 0;
@@ -314,6 +348,7 @@ static int bcm5482_read_status(struct phy_device *phydev)
static int bcm5481_config_aneg(struct phy_device *phydev)
{
+ struct device_node *np = phydev->mdio.dev.of_node;
int ret;
/* Aneg firsly. */
@@ -344,6 +379,14 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
phy_write(phydev, 0x18, reg);
}
+ if (of_property_read_bool(np, "enet-phy-lane-swap")) {
+ /* Lane Swap - Undocumented register...magic! */
+ ret = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_SEL_ER + 0x9,
+ 0x11B);
+ if (ret < 0)
+ return ret;
+ }
+
return ret;
}
@@ -578,6 +621,18 @@ static struct phy_driver broadcom_drivers[] = {
.ack_interrupt = bcm_phy_ack_intr,
.config_intr = bcm_phy_config_intr,
}, {
+ .phy_id = PHY_ID_BCM54810,
+ .phy_id_mask = 0xfffffff0,
+ .name = "Broadcom BCM54810",
+ .features = PHY_GBIT_FEATURES |
+ SUPPORTED_Pause | SUPPORTED_Asym_Pause,
+ .flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
+ .config_init = bcm54xx_config_init,
+ .config_aneg = bcm5481_config_aneg,
+ .read_status = genphy_read_status,
+ .ack_interrupt = bcm_phy_ack_intr,
+ .config_intr = bcm_phy_config_intr,
+}, {
.phy_id = PHY_ID_BCM5482,
.phy_id_mask = 0xfffffff0,
.name = "Broadcom BCM5482",
@@ -661,6 +716,7 @@ static struct mdio_device_id __maybe_unused broadcom_tbl[] = {
{ PHY_ID_BCM54616S, 0xfffffff0 },
{ PHY_ID_BCM5464, 0xfffffff0 },
{ PHY_ID_BCM5481, 0xfffffff0 },
+ { PHY_ID_BCM54810, 0xfffffff0 },
{ PHY_ID_BCM5482, 0xfffffff0 },
{ PHY_ID_BCM50610, 0xfffffff0 },
{ PHY_ID_BCM50610M, 0xfffffff0 },
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 0ed6691..848dc50 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -13,6 +13,7 @@
#define PHY_ID_BCM5241 0x0143bc30
#define PHY_ID_BCMAC131 0x0143bc70
#define PHY_ID_BCM5481 0x0143bca0
+#define PHY_ID_BCM54810 0x03625d00
#define PHY_ID_BCM5482 0x0143bcb0
#define PHY_ID_BCM5411 0x00206070
#define PHY_ID_BCM5421 0x002060e0
@@ -56,6 +57,7 @@
#define PHY_BRCM_EXT_IBND_TX_ENABLE 0x00002000
#define PHY_BRCM_CLEAR_RGMII_MODE 0x00004000
#define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00008000
+
/* Broadcom BCM7xxx specific workarounds */
#define PHY_BRCM_7XXX_REV(x) (((x) >> 8) & 0xff)
#define PHY_BRCM_7XXX_PATCH(x) ((x) & 0xff)
@@ -111,6 +113,7 @@
#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC 0x7000
#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC 0x0007
#define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT 12
+#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN (1 << 8)
#define MII_BCM54XX_AUXCTL_SHDWSEL_MASK 0x0007
@@ -192,6 +195,12 @@
#define BCM5482_SSD_SGMII_SLAVE_EN 0x0002 /* Slave mode enable */
#define BCM5482_SSD_SGMII_SLAVE_AD 0x0001 /* Slave auto-detection */
+/* BCM54810 Registers */
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL (MII_BCM54XX_EXP_SEL_ER + 0x90)
+#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN (1 << 0)
+#define BCM54810_SHD_CLK_CTL 0x3
+#define BCM54810_SHD_CLK_CTL_GTXCLK_EN (1 << 9)
+
/*****************************************************************************/
/* Fast Ethernet Transceiver definitions. */
--
2.7.4
^ permalink raw reply related
* [PATCH v6 2/7] Documentation: devicetree: add PHY lane swap binding
From: Jon Mason @ 2016-11-04 5:10 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
Add the documentation for PHY lane swapping. This is a boolean entry to
notify the phy device drivers that the TX/RX lanes need to be swapped.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
Documentation/devicetree/bindings/net/phy.txt | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt
index bc1c3c8..4627da3 100644
--- a/Documentation/devicetree/bindings/net/phy.txt
+++ b/Documentation/devicetree/bindings/net/phy.txt
@@ -35,6 +35,10 @@ Optional Properties:
- broken-turn-around: If set, indicates the PHY device does not correctly
release the turn around line low at the end of a MDIO transaction.
+- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to
+ compensate for the board being designed with the lanes swapped.
+
+
Example:
ethernet-phy at 0 {
--
2.7.4
^ permalink raw reply related
* [PATCH v6 1/7] net: phy: broadcom: add bcm54xx_auxctl_read
From: Jon Mason @ 2016-11-04 5:10 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1478236262-3351-1-git-send-email-jon.mason@broadcom.com>
Add a helper function to read the AUXCTL register for the BCM54xx. This
mirrors the bcm54xx_auxctl_write function already present in the code.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
drivers/net/phy/broadcom.c | 10 ++++++++++
include/linux/brcmphy.h | 1 +
2 files changed, 11 insertions(+)
diff --git a/drivers/net/phy/broadcom.c b/drivers/net/phy/broadcom.c
index 583ef8a..3a64b3d 100644
--- a/drivers/net/phy/broadcom.c
+++ b/drivers/net/phy/broadcom.c
@@ -30,6 +30,16 @@ MODULE_DESCRIPTION("Broadcom PHY driver");
MODULE_AUTHOR("Maciej W. Rozycki");
MODULE_LICENSE("GPL");
+static int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
+{
+ /* The register must be written to both the Shadow Register Select and
+ * the Shadow Read Register Selector
+ */
+ phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum |
+ regnum << MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT);
+ return phy_read(phydev, MII_BCM54XX_AUX_CTL);
+}
+
static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
{
return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
diff --git a/include/linux/brcmphy.h b/include/linux/brcmphy.h
index 60def78..0ed6691 100644
--- a/include/linux/brcmphy.h
+++ b/include/linux/brcmphy.h
@@ -110,6 +110,7 @@
#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX 0x0200
#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC 0x7000
#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC 0x0007
+#define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT 12
#define MII_BCM54XX_AUXCTL_SHDWSEL_MASK 0x0007
--
2.7.4
^ permalink raw reply related
* [PATCH v6 0/7] add NS2 support to bgmac
From: Jon Mason @ 2016-11-04 5:10 UTC (permalink / raw)
To: linux-arm-kernel
Changes in v6:
* Use a common bgmac_phy_connect_direct (per Rafal Milecki)
* Rebased on latest net-next
* Added Reviewed-by to the relevant patches
Changes in v5:
* Change a pr_err to netdev_err (per Scott Branden)
* Reword the lane swap binding documentation (per Andrew Lunn)
Changes in v4:
* Actually send out the lane swap binding doc patch (Per Scott Branden)
* Remove unused #define (Per Andrew Lunn)
Changes in v3:
* Clean-up the bgmac DT binding doc (per Rob Herring)
* Document the lane swap binding and make it generic (Per Andrew Lunn)
Changes in v2:
* Remove the PHY power-on (per Andrew Lunn)
* Misc PHY clean-ups regarding comments and #defines (per Andrew Lunn)
This results on none of the original PHY code from Vikas being
present. So, I'm removing him as an author and giving him
"Inspired-by" credit.
* Move PHY lane swapping to PHY driver (per Andrew Lunn and Florian
Fainelli)
* Remove bgmac sleep (per Florian Fainelli)
* Re-add bgmac chip reset (per Florian Fainelli and Ray Jui)
* Rebased on latest net-next
* Added patch for bcm54xx_auxctl_read, which is used in the BCM54810
Jon Mason (7):
net: phy: broadcom: add bcm54xx_auxctl_read
Documentation: devicetree: add PHY lane swap binding
net: phy: broadcom: Add BCM54810 PHY entry
Documentation: devicetree: net: add NS2 bindings to amac
net: ethernet: bgmac: device tree phy enablement
net: ethernet: bgmac: add NS2 support
arm64: dts: NS2: add AMAC ethernet support
.../devicetree/bindings/net/brcm,amac.txt | 16 +++--
Documentation/devicetree/bindings/net/phy.txt | 4 ++
arch/arm64/boot/dts/broadcom/ns2-svk.dts | 5 ++
arch/arm64/boot/dts/broadcom/ns2.dtsi | 12 ++++
drivers/net/ethernet/broadcom/bgmac-bcma.c | 22 +++++++
drivers/net/ethernet/broadcom/bgmac-platform.c | 74 +++++++++++++++++++++-
drivers/net/ethernet/broadcom/bgmac.c | 32 +++-------
drivers/net/ethernet/broadcom/bgmac.h | 9 +++
drivers/net/phy/Kconfig | 2 +-
drivers/net/phy/broadcom.c | 68 +++++++++++++++++++-
include/linux/brcmphy.h | 10 +++
11 files changed, 222 insertions(+), 32 deletions(-)
--
2.7.4
^ permalink raw reply
* [RESEND PATCH v1 05/11] dt-bindings: perf: hisi: Add Devicetree bindings for Hisilicon SoC PMU
From: Anurup M @ 2016-11-04 5:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161103182609.GA11071@kozik-lap>
On Thursday 03 November 2016 11:56 PM, Krzysztof Kozlowski wrote:
> On Thu, Nov 03, 2016 at 01:42:01AM -0400, Anurup M wrote:
>> 1) Device tree bindings for Hisilicon SoC PMU.
>> 2) Add example for Hisilicon L3 cache, MN and DDRC PMU.
> Get rid of this weird indentation in all patches.
Thanks. I shall remove the TAB from the commit message in all patches.
>
>> Signed-off-by: Anurup M <anurup.m@huawei.com>
>> Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
>> ---
>> .../devicetree/bindings/arm/hisilicon/pmu.txt | 127 +++++++++++++++++++++
>> 1 file changed, 127 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/arm/hisilicon/pmu.txt
>>
>> diff --git a/Documentation/devicetree/bindings/arm/hisilicon/pmu.txt b/Documentation/devicetree/bindings/arm/hisilicon/pmu.txt
>> new file mode 100644
>> index 0000000..e7b35e0
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/arm/hisilicon/pmu.txt
>> @@ -0,0 +1,127 @@
>> +Hisilicon SoC hip05/06/07 ARMv8 PMU
>> +===================================
>> +
>> +The Hisilicon SoC chips like hip05/06/07 etc. consist of varous independent
>> +system device PMU's such as L3 cache (L3C), Miscellaneous Nodes(MN) and DDR
>> +comtroller. These PMU devices are independent and have hardware logic to
>> +gather statistics and performance information.
>> +
>> +HiSilicon SoC chip is encapsulated by multiple CPU and IO die's. The CPU die
>> +is called as Super CPU cluster (SCCL) which includes 16 cpu-cores. Every SCCL
>> +is further grouped as CPU clusters (CCL) which includes 4 cpu-cores each.
>> +e.g. In the case of hip05/06/07, each SCCL has 1 L3 cache and 1 MN PMU device.
>> +
>> +The Hisilicon SoC PMU DT node bindigs for uncore PMU devices are as below.
>> +For PMU devices like L3 cache. MN etc. which are accessed using the djtag,
>> +the parent node will be the djtag node of the corresponding CPU die(SCCL).
>> +
>> +For uncore PMU devices there are some common required properties as detailed
>> +below.
>> +
>> +Required properties:
>> + - compatible : This field contain two values. The first value is
>> + always "hisilicon" and second value is the Module type as shown
>> + in below examples:
> Over-complicated sentence. Just:
>
> - compatible : One of:
> "hisilicon,hisi-pmu-l3c-v1" for Hisilicon SoC L3C PMU
> device (Version 1)
> ...
> ...
Thanks. Shall refine it in next version.
> BTW, No need of CC-ing me. I am not a maintainer of relevant subsystems.
Sure.
Thanks,
Anurup
> Best regards,
> Krzysztof
^ permalink raw reply
* [PATCH v2 2/2] power: bq27xxx_battery: add poll interval property query
From: Matt Ranostay @ 2016-11-04 5:00 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161102082206.GE21488@amd>
On Wed, Nov 2, 2016 at 1:22 AM, Pavel Machek <pavel@ucw.cz> wrote:
> Hi!
>
>> >> >> Better then previous one.
>> >> >>
>> >> >> But my version of bq27xxx_battery.c already contains this:
>> >> >
>> >> > This is for allowing udev rule to set the properties as well.
>> >> > otherwise a kinda crude RUN = " echo value >
>> >> > /sys/module/bq27xxx_battery/parameters/poll_interval" is required.
>> >>
>> >> Any thoughts on this?
>> >
>> > I'd say echo value >
>> > /sys/module/bq27xxx_battery/parameters/poll_interval .. is quite
>> > adequate solution...?
>> >
>> > Alternatively, convince us that something else is useful for everyone,
>> > and we can do the right thing (poll more often when battery is nearly
>> > empty), automatically...
>>
>> Ok should have had the patchset set it per device, and not use the
>> global poll_interval. Of need to add some logic to see if uses the
>> global poll_interval or it's own setting.
>>
>> There are times where you could have multiple batteries connected to
>> multiple fuel gauges, and want to up the polling interval on certain
>> ones that are discharging at different rates.
>>
>> But of course I'll let you guys let me know if this seems useful at all.
>
> I agree per-device polling would be cleaner.
>
Ok I'll work something up for RFC.
> But unless you have hardware with more than one bq27xxx, I'd avoid the
> work...
>
> Now... its also possible that poll_interval should change itself
> (within kernel) to do the right thing.
>
True but that is state machine territory, but I'll worry about that later...
> Best regards,
>
> Pavel
> --
> (english) http://www.livejournal.com/~pavelmachek
> (cesky, pictures) http://atrey.karlin.mff.cuni.cz/~pavel/picture/horses/blog.html
^ permalink raw reply
* [PATCH v2 2/3] irqchip: mtk-cirq: Add mediatek mtk-cirq implement
From: Youlin Pei @ 2016-11-04 4:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <86twbrj586.fsf@arm.com>
On Tue, 2016-11-01 at 20:49 +0000, Marc Zyngier wrote:
> On Tue, Nov 01 2016 at 11:52:01 AM, Youlin Pei <youlin.pei@mediatek.com> wrote:
> > In Mediatek SOCs, the CIRQ is a low power interrupt controller
> > designed to works outside MCUSYS which comprises with Cortex-Ax
> > cores,CCI and GIC.
> >
> > The CIRQ controller is integrated in between MCUSYS( include
> > Cortex-Ax, CCI and GIC ) and interrupt sources as the second
> > level interrupt controller. The external interrupts which outside
> > MCUSYS will feed through CIRQ then bypass to GIC. CIRQ can monitors
> > all edge trigger interupts. When an edge interrupt is triggered,
> > CIRQ can record the status and generate a pulse signal to GIC when
> > flush command executed.
> >
> > When system enters sleep mode, MCUSYS will be turned off to improve
> > power consumption, also GIC is power down. The edge trigger interrupts
> > will be lost in this scenario without CIRQ.
> >
> > This commit provides the CIRQ irqchip implement.
> >
> > Signed-off-by: Youlin Pei <youlin.pei@mediatek.com>
> > ---
> > drivers/irqchip/Makefile | 2 +-
> > drivers/irqchip/irq-mtk-cirq.c | 262 ++++++++++++++++++++++++++++++++++++++++
> > 2 files changed, 263 insertions(+), 1 deletion(-)
> > create mode 100644 drivers/irqchip/irq-mtk-cirq.c
> >
> > diff --git a/drivers/irqchip/Makefile b/drivers/irqchip/Makefile
> > index e4dbfc8..8f33580 100644
> > --- a/drivers/irqchip/Makefile
> > +++ b/drivers/irqchip/Makefile
> > @@ -60,7 +60,7 @@ obj-$(CONFIG_BCM7120_L2_IRQ) += irq-bcm7120-l2.o
> > obj-$(CONFIG_BRCMSTB_L2_IRQ) += irq-brcmstb-l2.o
> > obj-$(CONFIG_KEYSTONE_IRQ) += irq-keystone.o
> > obj-$(CONFIG_MIPS_GIC) += irq-mips-gic.o
> > -obj-$(CONFIG_ARCH_MEDIATEK) += irq-mtk-sysirq.o
> > +obj-$(CONFIG_ARCH_MEDIATEK) += irq-mtk-sysirq.o irq-mtk-cirq.o
> > obj-$(CONFIG_ARCH_DIGICOLOR) += irq-digicolor.o
> > obj-$(CONFIG_RENESAS_H8300H_INTC) += irq-renesas-h8300h.o
> > obj-$(CONFIG_RENESAS_H8S_INTC) += irq-renesas-h8s.o
> > diff --git a/drivers/irqchip/irq-mtk-cirq.c b/drivers/irqchip/irq-mtk-cirq.c
> > new file mode 100644
> > index 0000000..fc43ef3
> > --- /dev/null
> > +++ b/drivers/irqchip/irq-mtk-cirq.c
> > @@ -0,0 +1,262 @@
> > +/*
> > + * Copyright (c) 2016 MediaTek Inc.
> > + * Author: Youlin.Pei <youlin.pei@mediatek.com>
> > + *
> > + * This program is free software; you can redistribute it and/or modify
> > + * it under the terms of the GNU General Public License version 2 as
> > + * published by the Free Software Foundation.
> > + *
> > + * This program is distributed in the hope that it will be useful,
> > + * but WITHOUT ANY WARRANTY; without even the implied warranty of
> > + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> > + * GNU General Public License for more details.
> > + */
> > +
> > +#include <linux/irq.h>
> > +#include <linux/irqchip.h>
> > +#include <linux/irqdomain.h>
> > +#include <linux/of.h>
> > +#include <linux/of_irq.h>
> > +#include <linux/of_address.h>
> > +#include <linux/io.h>
> > +#include <linux/slab.h>
> > +#include <linux/syscore_ops.h>
> > +
> > +#define CIRQ_ACK 0x40
> > +#define CIRQ_MASK_SET 0xc0
> > +#define CIRQ_MASK_CLR 0x100
> > +#define CIRQ_SENS_SET 0x180
> > +#define CIRQ_SENS_CLR 0x1c0
> > +#define CIRQ_POL_SET 0x240
> > +#define CIRQ_POL_CLR 0x280
> > +#define CIRQ_CONTROL 0x300
> > +
> > +#define CIRQ_EN 0x1
> > +#define CIRQ_EDGE 0x2
> > +#define CIRQ_FLUSH 0x4
> > +
> > +#define CIRQ_IRQ_NUM 0x200
> > +
> > +struct mtk_cirq_chip_data {
> > + void __iomem *base;
> > + unsigned int ext_irq_start;
> > +};
> > +
> > +static struct mtk_cirq_chip_data *cirq_data;
>
> Are you guaranteed that you'll only ever have a single CIRQ in any
> system?
In Mediatek's SOC, only hace a single CIRQ.
>
> > +
> > +static void mtk_cirq_write_mask(struct irq_data *data, unsigned int offset)
> > +{
> > + struct mtk_cirq_chip_data *chip_data = data->chip_data;
> > + unsigned int cirq_num = data->hwirq;
> > + u32 mask = 1 << (cirq_num % 32);
> > +
> > + writel(mask, chip_data->base + offset + (cirq_num / 32) * 4);
>
> Why can't you use the relaxed accessors?
It seems that i use wrong function, i will change the writel to
writel_relaxed in next version.
>
> > +}
> > +
> > +static void mtk_cirq_mask(struct irq_data *data)
> > +{
> > + mtk_cirq_write_mask(data, CIRQ_MASK_SET);
> > + irq_chip_mask_parent(data);
> > +}
> > +
> > +static void mtk_cirq_unmask(struct irq_data *data)
> > +{
> > + mtk_cirq_write_mask(data, CIRQ_MASK_CLR);
> > + irq_chip_unmask_parent(data);
> > +}
> > +
> > +static void mtk_cirq_eoi(struct irq_data *data)
> > +{
> > + mtk_cirq_write_mask(data, CIRQ_ACK);
>
> EOI and ACK have very different semantics. What is this write actually
> doing? Also, you're now doing an additional MMIO write on each interrupt
> EOI, doubling its cost. Do you really need to do actually signal the HW
> that we've EOIed an interrupt? I would have hoped that you'd be able to
> put it in "bypass" mode as long as you're not suspending...
>
When external interrupt happened, CIRQ status register record the status
even CIRQ is not enabled. when execute the flush command, CIRQ will
resend the signals according to the status. So if don't clear the
status, CIRQ will resend the wrong signals. the ACK write operation will
clear the status.
> > + irq_chip_eoi_parent(data);
> > +}
> > +
> > +static int mtk_cirq_set_type(struct irq_data *data, unsigned int type)
> > +{
> > + int ret;
> > +
> > + switch (type & IRQ_TYPE_SENSE_MASK) {
> > + case IRQ_TYPE_EDGE_FALLING:
> > + mtk_cirq_write_mask(data, CIRQ_POL_CLR);
> > + mtk_cirq_write_mask(data, CIRQ_SENS_CLR);
> > + break;
> > + case IRQ_TYPE_EDGE_RISING:
> > + mtk_cirq_write_mask(data, CIRQ_POL_SET);
> > + mtk_cirq_write_mask(data, CIRQ_SENS_CLR);
> > + break;
> > + case IRQ_TYPE_LEVEL_LOW:
> > + mtk_cirq_write_mask(data, CIRQ_POL_CLR);
> > + mtk_cirq_write_mask(data, CIRQ_SENS_SET);
> > + break;
> > + case IRQ_TYPE_LEVEL_HIGH:
> > + mtk_cirq_write_mask(data, CIRQ_POL_SET);
> > + mtk_cirq_write_mask(data, CIRQ_SENS_SET);
> > + break;
> > + default:
> > + break;
> > + }
> > +
> > + data = data->parent_data;
> > + ret = data->chip->irq_set_type(data, type);
> > + return ret;
> > +}
> > +
> > +static struct irq_chip mtk_cirq_chip = {
> > + .name = "MT_CIRQ",
> > + .irq_mask = mtk_cirq_mask,
> > + .irq_unmask = mtk_cirq_unmask,
> > + .irq_eoi = mtk_cirq_eoi,
> > + .irq_set_type = mtk_cirq_set_type,
> > + .irq_retrigger = irq_chip_retrigger_hierarchy,
> > +#ifdef CONFIG_SMP
> > + .irq_set_affinity = irq_chip_set_affinity_parent,
> > +#endif
> > +};
> > +
> > +static int mtk_cirq_domain_translate(struct irq_domain *d,
> > + struct irq_fwspec *fwspec,
> > + unsigned long *hwirq,
> > + unsigned int *type)
> > +{
> > + if (is_of_node(fwspec->fwnode)) {
> > + if (fwspec->param_count != 3)
> > + return -EINVAL;
> > +
> > + /* No PPI should point to this domain */
> > + if (fwspec->param[0] != 0)
> > + return -EINVAL;
> > +
> > + /* cirq support irq number check */
> > + if (fwspec->param[1] < cirq_data->ext_irq_start)
> > + return -EINVAL;
> > +
> > + *hwirq = fwspec->param[1] - cirq_data->ext_irq_start;
>
> What if the result is > CIRQ_IRQ_NUM?
will add CIRQ supported irq range in DT, and do range check here in next
version.
>
> > + *type = fwspec->param[2] & IRQ_TYPE_SENSE_MASK;
> > + return 0;
> > + }
> > +
> > + return -EINVAL;
> > +}
> > +
> > +static int mtk_cirq_domain_alloc(struct irq_domain *domain, unsigned int virq,
> > + unsigned int nr_irqs, void *arg)
> > +{
> > + int i;
> > + irq_hw_number_t hwirq;
> > + struct irq_fwspec *fwspec = arg;
> > + struct irq_fwspec parent_fwspec = *fwspec;
> > +
> > + if (fwspec->param_count != 3)
> > + return -EINVAL;
> > +
> > + /* cirq doesn't support PPI */
> > + if (fwspec->param[0])
> > + return -EINVAL;
> > +
> > + if (fwspec->param[1] < cirq_data->ext_irq_start)
> > + return -EINVAL;
> > +
> > + hwirq = fwspec->param[1] - cirq_data->ext_irq_start;
>
> All this is a pure copy of mtk_cirq_domain_translate(). Please use it.
will fix in next version.
> > + for (i = 0; i < nr_irqs; i++)
> > + irq_domain_set_hwirq_and_chip(domain, virq + i, hwirq + i,
> > + &mtk_cirq_chip,
> > + domain->host_data);
>
> This is a bit silly. This loop only exists for the benefit of MSI
> support, which we're not dealing with here. So please stick a
>
> if (WARN_ON(nr_irqs != 1))
> return -EINVAL;
>
> and drop the loop.
will fix in next version.
>
> > +
> > + parent_fwspec.fwnode = domain->parent->fwnode;
> > + return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs,
> > + &parent_fwspec);
> > +}
> > +
> > +static const struct irq_domain_ops cirq_domain_ops = {
> > + .translate = mtk_cirq_domain_translate,
> > + .alloc = mtk_cirq_domain_alloc,
> > + .free = irq_domain_free_irqs_common,
> > +};
> > +
> > +#ifdef CONFIG_PM_SLEEP
> > +static int mtk_cirq_suspend(void)
> > +{
> > + u32 value;
> > +
> > + /* set edge_only mode, record edge-triggerd interrupts */
> > + /* enable cirq */
> > + value = readl_relaxed(cirq_data->base + CIRQ_CONTROL);
> > + value |= (CIRQ_EDGE | CIRQ_EN);
> > + writel(value, cirq_data->base + CIRQ_CONTROL);
>
> You're mixing relaxed and non-relaxed accessors. Why?
will change writel to writel_relaxed in next version.
>
> > + return 0;
> > +}
> > +
> > +static void mtk_cirq_resume(void)
> > +{
> > + u32 value;
> > +
> > + /* flush recored interrupts, will send signals to parent controller */
> > + value = readl_relaxed(cirq_data->base + CIRQ_CONTROL);
> > + writel(value | CIRQ_FLUSH, cirq_data->base + CIRQ_CONTROL);
>
> Same remark.
will change writel to writel_relaxed in next version.
>
> > +
> > + /* disable cirq */
> > + value = readl_relaxed(cirq_data->base + CIRQ_CONTROL);
> > + value &= ~(CIRQ_EDGE | CIRQ_EN);
> > + writel(value, cirq_data->base + CIRQ_CONTROL);
>
> So from this, I infer that CIRQ is not enabled when the kernel is
> running (not suspended). It really makes me wonder why you need to do
> anything in the EOI callback.
>
> > +}
> > +
> > +static struct syscore_ops mtk_cirq_syscore_ops = {
> > + .suspend = mtk_cirq_suspend,
> > + .resume = mtk_cirq_resume,
> > +};
> > +
> > +static void mtk_cirq_syscore_init(void)
> > +{
> > + register_syscore_ops(&mtk_cirq_syscore_ops);
> > +}
> > +#else
> > +static inline void mtk_cirq_syscore_init(void) {}
> > +#endif
> > +
> > +static int __init mtk_cirq_of_init(struct device_node *node,
> > + struct device_node *parent)
> > +{
> > + struct irq_domain *domain, *domain_parent;
> > + int ret;
> > +
> > + domain_parent = irq_find_host(parent);
> > + if (!domain_parent) {
> > + pr_err("mtk_cirq: interrupt-parent not found\n");
> > + return -EINVAL;
> > + }
> > +
> > + cirq_data = kzalloc(sizeof(*cirq_data), GFP_KERNEL);
> > + if (!cirq_data)
> > + return -ENOMEM;
> > +
> > + cirq_data->base = of_iomap(node, 0);
> > + if (!cirq_data->base) {
> > + pr_err("mtk_cirq: unable to map cirq register\n");
> > + ret = -ENXIO;
> > + goto out_free;
> > + }
> > +
> > + ret = of_property_read_u32(node, "mediatek,ext-irq-start",
> > + &cirq_data->ext_irq_start);
> > + if (ret)
> > + goto out_unmap;
> > +
> > + domain = irq_domain_add_hierarchy(domain_parent, 0, CIRQ_IRQ_NUM, node,
> > + &cirq_domain_ops, cirq_data);
>
> So you support at most 512 interrupts, and yet the GIC supports up to
> 987 SPIs. What happens for interrupt lines that out of the CIRQ range?
> Maybe having an explicit range in DT would be a good thing. That also
> brings back the question of having a single CIRQ in the system...
>
In next version, i will add an explicit CIRQ supported range in DT.
Thanks a lot!
> > + if (!domain) {
> > + ret = -ENOMEM;
> > + goto out_unmap;
> > + }
> > +
> > + mtk_cirq_syscore_init();
> > +
> > + return 0;
> > +
> > +out_unmap:
> > + iounmap(cirq_data->base);
> > +out_free:
> > + kfree(cirq_data);
> > + return ret;
> > +}
> > +
> > +IRQCHIP_DECLARE(mtk_cirq, "mediatek,mtk-cirq", mtk_cirq_of_init);
>
> Thanks,
>
> M.
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox