* [PATCH 07/12] arm64: dts: r8a7796: salvator-x: enable SDHI0 & 3
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478251192.git.horms+renesas@verge.net.au>
Enable the exposed SD card slots in the DT of the r8a7796/salvator-x.
Based on work for the r8a7795/salvator-x by Ai Kyuse.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 84 ++++++++++++++++++++++
1 file changed, 84 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 90e9a76c8b30..c946569accb1 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -10,6 +10,7 @@
/dts-v1/;
#include "r8a7796.dtsi"
+#include <dt-bindings/gpio/gpio.h>
/ {
model = "Renesas Salvator-X board based on r8a7796";
@@ -29,6 +30,55 @@
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x78000000>;
};
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
+ vcc_sdhi3: regulator-vcc-sdhi3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI3 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio3 15 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi3: regulator-vccq-sdhi3 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI3 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio3 14 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
+
};
&pfc {
@@ -43,6 +93,16 @@
groups = "scif_clk_a";
function = "scif_clk";
};
+
+ sdhi0_pins: sd0 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ };
+
+ sdhi3_pins: sd3 {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ };
};
&extal_clk {
@@ -53,6 +113,30 @@
clock-frequency = <32768>;
};
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ status = "okay";
+};
+
+&sdhi3 {
+ pinctrl-0 = <&sdhi3_pins>;
+ pinctrl-names = "default";
+
+ vmmc-supply = <&vcc_sdhi3>;
+ vqmmc-supply = <&vccq_sdhi3>;
+ cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
+ wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
+ bus-width = <4>;
+ status = "okay";
+};
+
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 03/29] ARM: dts: koelsch: enable UHS for SDHI 0, 1 & 3
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1,2}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 33 ++++++++++++++++++++++++++++++---
1 file changed, 30 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index f8a7d090fd01..f17bfa000f73 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -360,16 +360,37 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi1_pins: sd1 {
groups = "sdhi1_data4", "sdhi1_ctrl";
function = "sdhi1";
+ power-source = <3300>;
+ };
+
+ sdhi1_pins_uhs: sd1_uhs {
+ groups = "sdhi1_data4", "sdhi1_ctrl";
+ function = "sdhi1";
+ power-source = <1800>;
};
sdhi2_pins: sd2 {
groups = "sdhi2_data4", "sdhi2_ctrl";
function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data4", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
};
qspi_pins: qspi {
@@ -454,33 +475,39 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio6 7 GPIO_ACTIVE_HIGH>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi1 {
pinctrl-0 = <&sdhi1_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi1_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi1>;
vqmmc-supply = <&vccq_sdhi1>;
cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio6 15 GPIO_ACTIVE_HIGH>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi2 {
pinctrl-0 = <&sdhi2_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi2>;
vqmmc-supply = <&vccq_sdhi2>;
cd-gpios = <&gpio6 22 GPIO_ACTIVE_LOW>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 08/12] arm64: dts: r8a7796: salvator-x: enable UHS for SDHI 0 & 3
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478251192.git.horms+renesas@verge.net.au>
Based on work for the r8a7796 by Wolfram Sang.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 22 ++++++++++++++++++++--
1 file changed, 20 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index c946569accb1..08c335afd970 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -97,11 +97,25 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
+ power-source = <3300>;
+ };
+
+ sdhi3_pins_uhs: sd3_uhs {
+ groups = "sdhi3_data4", "sdhi3_ctrl";
+ function = "sdhi3";
+ power-source = <1800>;
};
};
@@ -115,25 +129,29 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio3 13 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi3_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi3>;
vqmmc-supply = <&vccq_sdhi3>;
cd-gpios = <&gpio4 15 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio4 16 GPIO_ACTIVE_HIGH>;
bus-width = <4>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 04/29] ARM: dts: r8a7794: set maximum frequency for SDHI clocks
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
Define the upper limit otherwise the driver cannot utilize max speeds.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
arch/arm/boot/dts/r8a7794.dtsi | 3 +++
1 file changed, 3 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 9365580a194f..57e0d27cb82e 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -731,6 +731,7 @@
dmas = <&dmac0 0xcd>, <&dmac0 0xce>,
<&dmac1 0xcd>, <&dmac1 0xce>;
dma-names = "tx", "rx", "tx", "rx";
+ max-frequency = <195000000>;
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -743,6 +744,7 @@
dmas = <&dmac0 0xc1>, <&dmac0 0xc2>,
<&dmac1 0xc1>, <&dmac1 0xc2>;
dma-names = "tx", "rx", "tx", "rx";
+ max-frequency = <97500000>;
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
@@ -755,6 +757,7 @@
dmas = <&dmac0 0xd3>, <&dmac0 0xd4>,
<&dmac1 0xd3>, <&dmac1 0xd4>;
dma-names = "tx", "rx", "tx", "rx";
+ max-frequency = <97500000>;
power-domains = <&sysc R8A7794_PD_ALWAYS_ON>;
status = "disabled";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.10
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
Hi Olof, Hi Kevin, Hi Arnd,
Please consider these Renesas ARM64 based SoC DT updates for v4.10.
The following changes since commit 1001354ca34179f3db924eb66672442a173147dc:
Linux 4.9-rc1 (2016-10-15 12:17:50 -0700)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt-for-v4.10
for you to fetch changes up to 935085209343a0c507e3d9a3e01883b25c8f743e:
arm64: renesas: r8a7796: add SYS-DMAC controller nodes (2016-11-04 10:18:07 +0100)
----------------------------------------------------------------
Renesas ARM64 Based SoC DT Updates for v4.10
Enablement:
* Enable On-board eMMC
* Enable SDHI 0 & 3 with UHS
* Add SYS-DMAC controller nodes to r8a7796 SoC
* Populate EXTALR on r8a7796/salvator-x board; used by watchdog
* Add DU LVDS output endpoint on r8a7795/salvator-x board
* Add bias setting for USB1 pins on r8a7795/salvator-x board
Clean-Up:
* Remove FCP SoC-specific compatible strings
----------------------------------------------------------------
Geert Uytterhoeven (1):
arm64: dts: r8a7796: salvator-x: Populate EXTALR
Laurent Pinchart (3):
arm64: dts: r8a7795: salvator-x: Add DU LVDS output endpoint
dt-bindings: media: renesas-fcp: Remove SoC-specific compatible strings
arm64: dts: r8a7795: Remove FCP SoC-specific compatible strings
Simon Horman (3):
arm64: dts: r8a7796: add SDHI nodes
arm64: dts: r8a7796: salvator-x: enable SDHI0 & 3
arm64: dts: r8a7796: salvator-x: enable UHS for SDHI 0 & 3
Ulrich Hecht (1):
arm64: renesas: r8a7796: add SYS-DMAC controller nodes
Wolfram Sang (3):
arm64: dts: r8a7795: salvator-x: enable UHS for SDHI 0 & 3
arm64: dts: r8a7795: salvator: enable on-board eMMC
arm64: dts: r8a7796: salvator: enable on board eMMC
Yoshihiro Shimoda (1):
arm64: dts: r8a7795: salvator-x: add bias setting for usb1_pins
.../devicetree/bindings/media/renesas,fcp.txt | 8 +-
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 85 +++++++++++-
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 24 ++--
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 148 +++++++++++++++++++++
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 139 +++++++++++++++++++
5 files changed, 381 insertions(+), 23 deletions(-)
^ permalink raw reply
* [PATCH 09/12] arm64: dts: r8a7795: salvator: enable on-board eMMC
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478251192.git.horms+renesas@verge.net.au>
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 43 ++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index c8f6023c4667..da3e996ba121 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -62,6 +62,24 @@
clock-frequency = <24576000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -250,6 +268,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
@@ -401,6 +431,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
pinctrl-1 = <&sdhi3_pins_uhs>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 05/29] ARM: dts: alt: enable UHS for SDHI 0 & 1
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
Add the "1v8" pinctrl state and sd-uhs-sdr50 property to SDHI{0,1}.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
---
arch/arm/boot/dts/r8a7794-alt.dts | 22 ++++++++++++++++++++--
1 file changed, 20 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794-alt.dts b/arch/arm/boot/dts/r8a7794-alt.dts
index 8d1b35afaf82..325d3f972c57 100644
--- a/arch/arm/boot/dts/r8a7794-alt.dts
+++ b/arch/arm/boot/dts/r8a7794-alt.dts
@@ -207,11 +207,25 @@
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
};
sdhi1_pins: sd1 {
groups = "sdhi1_data4", "sdhi1_ctrl";
function = "sdhi1";
+ power-source = <3300>;
+ };
+
+ sdhi1_pins_uhs: sd1_uhs {
+ groups = "sdhi1_data4", "sdhi1_ctrl";
+ function = "sdhi1";
+ power-source = <1800>;
};
};
@@ -255,23 +269,27 @@
&sdhi0 {
pinctrl-0 = <&sdhi0_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
vqmmc-supply = <&vccq_sdhi0>;
cd-gpios = <&gpio6 6 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio6 7 GPIO_ACTIVE_LOW>;
+ sd-uhs-sdr50;
status = "okay";
};
&sdhi1 {
pinctrl-0 = <&sdhi1_pins>;
- pinctrl-names = "default";
+ pinctrl-1 = <&sdhi1_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi1>;
vqmmc-supply = <&vccq_sdhi1>;
cd-gpios = <&gpio6 14 GPIO_ACTIVE_LOW>;
wp-gpios = <&gpio6 15 GPIO_ACTIVE_LOW>;
+ sd-uhs-sdr50;
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 10/12] arm64: dts: r8a7796: salvator: enable on board eMMC
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478251192.git.horms+renesas@verge.net.au>
From: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 44 +++++++++++++++++++++-
1 file changed, 43 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index 08c335afd970..a9c296b1e1b7 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -31,6 +31,24 @@
reg = <0x0 0x48000000 0x0 0x78000000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -78,7 +96,6 @@
states = <3300000 1
1800000 0>;
};
-
};
&pfc {
@@ -106,6 +123,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sdhi3_pins: sd3 {
groups = "sdhi3_data4", "sdhi3_ctrl";
function = "sdhi3";
@@ -141,6 +170,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&sdhi3 {
pinctrl-0 = <&sdhi3_pins>;
pinctrl-1 = <&sdhi3_pins_uhs>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 06/29] ARM: dts: r8a7790: Correct SCIFB reg properties to cover all registers
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7790.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790.dtsi b/arch/arm/boot/dts/r8a7790.dtsi
index 351fcc2f87df..a946474be9cf 100644
--- a/arch/arm/boot/dts/r8a7790.dtsi
+++ b/arch/arm/boot/dts/r8a7790.dtsi
@@ -711,7 +711,7 @@
scifb0: serial at e6c20000 {
compatible = "renesas,scifb-r8a7790",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c20000 0 64>;
+ reg = <0 0xe6c20000 0 0x100>;
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFB0>;
clock-names = "fck";
@@ -725,7 +725,7 @@
scifb1: serial at e6c30000 {
compatible = "renesas,scifb-r8a7790",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c30000 0 64>;
+ reg = <0 0xe6c30000 0 0x100>;
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFB1>;
clock-names = "fck";
@@ -739,7 +739,7 @@
scifb2: serial at e6ce0000 {
compatible = "renesas,scifb-r8a7790",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6ce0000 0 64>;
+ reg = <0 0xe6ce0000 0 0x100>;
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7790_CLK_SCIFB2>;
clock-names = "fck";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 11/12] arm64: dts: r8a7795: salvator-x: add bias setting for usb1_pins
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478251192.git.horms+renesas@verge.net.au>
From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Since this board doesn't mount pull-up/down registers for
USB1_{OVC,PWEN} pins, we should enable bias setting to pull these
pins up/down.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts | 16 ++++++++++++++--
1 file changed, 14 insertions(+), 2 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
index da3e996ba121..bcaf4008d32d 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-salvator-x.dts
@@ -309,8 +309,20 @@
};
usb1_pins: usb1 {
- groups = "usb1";
- function = "usb1";
+ mux {
+ groups = "usb1";
+ function = "usb1";
+ };
+
+ ovc {
+ pins = "GP_6_27";
+ bias-pull-up;
+ };
+
+ pwen {
+ pins = "GP_6_26";
+ bias-pull-down;
+ };
};
usb2_pins: usb2 {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 07/29] ARM: dts: r8a7791: Correct SCIFB reg properties to cover all registers
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7791.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791.dtsi b/arch/arm/boot/dts/r8a7791.dtsi
index b07c799f72f2..091d7fb6ee7d 100644
--- a/arch/arm/boot/dts/r8a7791.dtsi
+++ b/arch/arm/boot/dts/r8a7791.dtsi
@@ -702,7 +702,7 @@
scifb0: serial at e6c20000 {
compatible = "renesas,scifb-r8a7791",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c20000 0 64>;
+ reg = <0 0xe6c20000 0 0x100>;
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFB0>;
clock-names = "fck";
@@ -716,7 +716,7 @@
scifb1: serial at e6c30000 {
compatible = "renesas,scifb-r8a7791",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c30000 0 64>;
+ reg = <0 0xe6c30000 0 0x100>;
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFB1>;
clock-names = "fck";
@@ -730,7 +730,7 @@
scifb2: serial at e6ce0000 {
compatible = "renesas,scifb-r8a7791",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6ce0000 0 64>;
+ reg = <0 0xe6ce0000 0 0x100>;
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7791_CLK_SCIFB2>;
clock-names = "fck";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 12/12] arm64: renesas: r8a7796: add SYS-DMAC controller nodes
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478251192.git.horms+renesas@verge.net.au>
From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 99 ++++++++++++++++++++++++++++++++
1 file changed, 99 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 6ec988c78ff8..f9cb7796ad49 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -252,6 +252,105 @@
status = "disabled";
};
+ dmac0: dma-controller at e6700000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe6700000 0 0x10000>;
+ interrupts = <GIC_SPI 199 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 206 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 209 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 210 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 211 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 212 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 213 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 214 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 219>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
+ dmac1: dma-controller at e7300000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe7300000 0 0x10000>;
+ interrupts = <GIC_SPI 220 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 216 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 217 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 218 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 219 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 308 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 309 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 310 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 311 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 312 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 313 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 314 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 315 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 316 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 317 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 318 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 319 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 218>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
+ dmac2: dma-controller at e7310000 {
+ compatible = "renesas,dmac-r8a7796",
+ "renesas,rcar-dmac";
+ reg = <0 0xe7310000 0 0x10000>;
+ interrupts = <GIC_SPI 416 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 417 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 418 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 419 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 420 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 421 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 422 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 423 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 424 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 425 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 426 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 427 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 428 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 429 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 430 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 431 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 397 IRQ_TYPE_LEVEL_HIGH>;
+ interrupt-names = "error",
+ "ch0", "ch1", "ch2", "ch3",
+ "ch4", "ch5", "ch6", "ch7",
+ "ch8", "ch9", "ch10", "ch11",
+ "ch12", "ch13", "ch14", "ch15";
+ clocks = <&cpg CPG_MOD 217>;
+ clock-names = "fck";
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ #dma-cells = <1>;
+ dma-channels = <16>;
+ };
+
sdhi0: sd at ee100000 {
compatible = "renesas,sdhi-r8a7796";
reg = <0 0xee100000 0 0x2000>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 08/29] ARM: dts: r8a7793: Correct SCIFB reg properties to cover all registers
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7793.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793.dtsi b/arch/arm/boot/dts/r8a7793.dtsi
index 8d02aacf2892..a7d11b9f3555 100644
--- a/arch/arm/boot/dts/r8a7793.dtsi
+++ b/arch/arm/boot/dts/r8a7793.dtsi
@@ -666,7 +666,7 @@
scifb0: serial at e6c20000 {
compatible = "renesas,scifb-r8a7793",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c20000 0 64>;
+ reg = <0 0xe6c20000 0 0x100>;
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFB0>;
clock-names = "fck";
@@ -680,7 +680,7 @@
scifb1: serial at e6c30000 {
compatible = "renesas,scifb-r8a7793",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c30000 0 64>;
+ reg = <0 0xe6c30000 0 0x100>;
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFB1>;
clock-names = "fck";
@@ -694,7 +694,7 @@
scifb2: serial at e6ce0000 {
compatible = "renesas,scifb-r8a7793",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6ce0000 0 64>;
+ reg = <0 0xe6ce0000 0 0x100>;
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7793_CLK_SCIFB2>;
clock-names = "fck";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 09/29] ARM: dts: r8a7794: Correct SCIFB reg properties to cover all registers
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Several SCIFB registers reside outside the reported register ranges.
Fortunately this works (on Linux), due to the PAGE_SIZE granularity of
ioremap().
Extend the sizes from 64 to 0x100 bytes to fix this, like is done on
SH/R-Mobile SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7794.dtsi | 6 +++---
1 file changed, 3 insertions(+), 3 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 57e0d27cb82e..8cfc1385f58a 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -411,7 +411,7 @@
scifb0: serial at e6c20000 {
compatible = "renesas,scifb-r8a7794",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c20000 0 64>;
+ reg = <0 0xe6c20000 0 0x100>;
interrupts = <GIC_SPI 148 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFB0>;
clock-names = "fck";
@@ -425,7 +425,7 @@
scifb1: serial at e6c30000 {
compatible = "renesas,scifb-r8a7794",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6c30000 0 64>;
+ reg = <0 0xe6c30000 0 0x100>;
interrupts = <GIC_SPI 149 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFB1>;
clock-names = "fck";
@@ -439,7 +439,7 @@
scifb2: serial at e6ce0000 {
compatible = "renesas,scifb-r8a7794",
"renesas,rcar-gen2-scifb", "renesas,scifb";
- reg = <0 0xe6ce0000 0 64>;
+ reg = <0 0xe6ce0000 0 0x100>;
interrupts = <GIC_SPI 150 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&mstp2_clks R8A7794_CLK_SCIFB2>;
clock-names = "fck";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 10/29] ARM: dts: wheat: add DU support
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the Wheat board dependent part of the DU device node.
Add the device nodes for the Analog Devices ADV7513 HDMI transmitters
connected to DU0/1. Add the necessary subnodes to interconnect DU with
HDMI transmitters/connectors.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7792-wheat.dts | 126 ++++++++++++++++++++++++++++++++++++
1 file changed, 126 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7792-wheat.dts b/arch/arm/boot/dts/r8a7792-wheat.dts
index 6dbb94114a93..c24f26fdab1f 100644
--- a/arch/arm/boot/dts/r8a7792-wheat.dts
+++ b/arch/arm/boot/dts/r8a7792-wheat.dts
@@ -86,6 +86,34 @@
gpio = <&gpio11 12 GPIO_ACTIVE_HIGH>;
enable-active-high;
};
+
+ hdmi-out0 {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con0: endpoint {
+ remote-endpoint = <&adv7513_0_out>;
+ };
+ };
+ };
+
+ hdmi-out1 {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con1: endpoint {
+ remote-endpoint = <&adv7513_1_out>;
+ };
+ };
+ };
+
+ osc2_clk: osc2 {
+ compatible = "fixed-clock";
+ #clock-cells = <0>;
+ clock-frequency = <74250000>;
+ };
};
&extal_clk {
@@ -128,6 +156,16 @@
groups = "qspi_ctrl", "qspi_data4";
function = "qspi";
};
+
+ du0_pins: du0 {
+ groups = "du0_rgb888", "du0_sync", "du0_disp";
+ function = "du0";
+ };
+
+ du1_pins: du1 {
+ groups = "du1_rgb666", "du1_sync", "du1_disp";
+ function = "du1";
+ };
};
&scif0 {
@@ -197,3 +235,91 @@
};
};
};
+
+&i2c4 {
+ status = "okay";
+ clock-frequency = <400000>;
+
+ hdmi at 3d {
+ compatible = "adi,adv7513";
+ reg = <0x3d>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7513_0_in: endpoint {
+ remote-endpoint = <&du_out_rgb0>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7513_0_out: endpoint {
+ remote-endpoint = <&hdmi_con0>;
+ };
+ };
+ };
+ };
+
+ hdmi at 39 {
+ compatible = "adi,adv7513";
+ reg = <0x39>;
+
+ adi,input-depth = <8>;
+ adi,input-colorspace = "rgb";
+ adi,input-clock = "1x";
+ adi,input-style = <1>;
+ adi,input-justification = "evenly";
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7513_1_in: endpoint {
+ remote-endpoint = <&du_out_rgb1>;
+ };
+ };
+
+ port at 1 {
+ reg = <1>;
+ adv7513_1_out: endpoint {
+ remote-endpoint = <&hdmi_con1>;
+ };
+ };
+ };
+ };
+};
+
+&du {
+ pinctrl-0 = <&du0_pins &du1_pins>;
+ pinctrl-names = "default";
+
+ clocks = <&mstp7_clks R8A7792_CLK_DU0>, <&mstp7_clks R8A7792_CLK_DU1>,
+ <&osc2_clk>;
+ clock-names = "du.0", "du.1", "dclkin.0";
+ status = "okay";
+
+ ports {
+ port at 0 {
+ endpoint {
+ remote-endpoint = <&adv7513_0_in>;
+ };
+ };
+ port at 1 {
+ endpoint {
+ remote-endpoint = <&adv7513_1_in>;
+ };
+ };
+ };
+};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 11/29] ARM: dts: r8a7792: add MSIOF clocks
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Describe the MSIOF0/1 clocks and their parent, MP clock in the R8A7792
device tree.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7792.dtsi | 21 +++++++++++++++++++--
1 file changed, 19 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 713141d38b3e..839cd70c4c75 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -763,6 +763,13 @@
clock-div = <48>;
clock-mult = <1>;
};
+ mp_clk: mp {
+ compatible = "fixed-factor-clock";
+ clocks = <&pll1_div2_clk>;
+ #clock-cells = <0>;
+ clock-div = <15>;
+ clock-mult = <1>;
+ };
m2_clk: m2 {
compatible = "fixed-factor-clock";
clocks = <&cpg_clocks R8A7792_CLK_PLL1>;
@@ -793,6 +800,15 @@
};
/* Gate clocks */
+ mstp0_clks: mstp0_clks at e6150130 {
+ compatible = "renesas,r8a7792-mstp-clocks",
+ "renesas,cpg-mstp-clocks";
+ reg = <0 0xe6150130 0 4>, <0 0xe6150030 0 4>;
+ clocks = <&mp_clk>;
+ #clock-cells = <1>;
+ clock-indices = <R8A7792_CLK_MSIOF0>;
+ clock-output-names = "msiof0";
+ };
mstp1_clks: mstp1_clks at e6150134 {
compatible = "renesas,r8a7792-mstp-clocks",
"renesas,cpg-mstp-clocks";
@@ -811,12 +827,13 @@
compatible = "renesas,r8a7792-mstp-clocks",
"renesas,cpg-mstp-clocks";
reg = <0 0xe6150138 0 4>, <0 0xe6150040 0 4>;
- clocks = <&zs_clk>, <&zs_clk>;
+ clocks = <&mp_clk>, <&zs_clk>, <&zs_clk>;
#clock-cells = <1>;
clock-indices = <
+ R8A7792_CLK_MSIOF1
R8A7792_CLK_SYS_DMAC1 R8A7792_CLK_SYS_DMAC0
>;
- clock-output-names = "sys-dmac1", "sys-dmac0";
+ clock-output-names = "msiof1", "sys-dmac1", "sys-dmac0";
};
mstp3_clks: mstp3_clks at e615013c {
compatible = "renesas,r8a7792-mstp-clocks",
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 12/29] ARM: dts: r8a7792: add MSIOF support
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Define the generic R8A7792 parts of the MSIOF0/1 device nodes.
Based on the original (and large) patch by Vladimir Barinov
<vladimir.barinov@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7792.dtsi | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/r8a7792.dtsi b/arch/arm/boot/dts/r8a7792.dtsi
index 839cd70c4c75..a75e0cd312c5 100644
--- a/arch/arm/boot/dts/r8a7792.dtsi
+++ b/arch/arm/boot/dts/r8a7792.dtsi
@@ -26,6 +26,8 @@
i2c4 = &i2c4;
i2c5 = &i2c5;
spi0 = &qspi;
+ spi1 = &msiof0;
+ spi2 = &msiof1;
vin0 = &vin0;
vin1 = &vin1;
vin2 = &vin2;
@@ -572,6 +574,34 @@
status = "disabled";
};
+ msiof0: spi at e6e20000 {
+ compatible = "renesas,msiof-r8a7792";
+ reg = <0 0xe6e20000 0 0x0064>;
+ interrupts = <GIC_SPI 156 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp0_clks R8A7792_CLK_MSIOF0>;
+ dmas = <&dmac0 0x51>, <&dmac0 0x52>,
+ <&dmac1 0x51>, <&dmac1 0x52>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
+ msiof1: spi at e6e10000 {
+ compatible = "renesas,msiof-r8a7792";
+ reg = <0 0xe6e10000 0 0x0064>;
+ interrupts = <GIC_SPI 157 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp2_clks R8A7792_CLK_MSIOF1>;
+ dmas = <&dmac0 0x55>, <&dmac0 0x56>,
+ <&dmac1 0x55>, <&dmac1 0x56>;
+ dma-names = "tx", "rx", "tx", "rx";
+ power-domains = <&sysc R8A7792_PD_ALWAYS_ON>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "disabled";
+ };
+
du: display at feb00000 {
compatible = "renesas,du-r8a7792";
reg = <0 0xfeb00000 0 0x40000>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 13/29] ARM: dts: r7s72100: add mmcif to device tree
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r7s72100.dtsi | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index e18d4e645d6e..50f9f3bc109d 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -450,4 +450,16 @@
#size-cells = <0>;
status = "disabled";
};
+
+ mmcif: mmc at e804c800 {
+ compatible = "renesas,mmcif-r7s72100", "renesas,sh-mmcif";
+ reg = <0xe804c800 0x80>;
+ interrupts = <GIC_SPI 268 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 269 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 267 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&mstp8_clks R7S72100_CLK_MMCIF>;
+ reg-io-width = <4>;
+ bus-width = <8>;
+ status = "disabled";
+ };
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 14/29] ARM: dts: r7s72100: add sdhi clock to device tree
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r7s72100.dtsi | 8 ++++++++
include/dt-bindings/clock/r7s72100-clock.h | 4 ++++
2 files changed, 12 insertions(+)
diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index 50f9f3bc109d..eab06701ef11 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -149,6 +149,14 @@
>;
clock-output-names = "spi0", "spi1", "spi2", "spi3", "spi4";
};
+ mstp12_clks: mstp12_clks at fcfe0444 {
+ #clock-cells = <1>;
+ compatible = "renesas,r7s72100-mstp-clocks", "renesas,cpg-mstp-clocks";
+ reg = <0xfcfe0444 4>;
+ clocks = <&p1_clk>, <&p1_clk>;
+ clock-indices = <R7S72100_CLK_SDHI1 R7S72100_CLK_SDHI0>;
+ clock-output-names = "sdhi1", "sdhi0";
+ };
};
cpus {
diff --git a/include/dt-bindings/clock/r7s72100-clock.h b/include/dt-bindings/clock/r7s72100-clock.h
index 5eaf0fb469c2..29e01ed10e74 100644
--- a/include/dt-bindings/clock/r7s72100-clock.h
+++ b/include/dt-bindings/clock/r7s72100-clock.h
@@ -44,4 +44,8 @@
#define R7S72100_CLK_SPI3 4
#define R7S72100_CLK_SPI4 3
+/* MSTP12 */
+#define R7S72100_CLK_SDHI0 3
+#define R7S72100_CLK_SDHI1 2
+
#endif /* __DT_BINDINGS_CLOCK_R7S72100_H__ */
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 15/29] ARM: dts: gose: use generic pinctrl properties in SDHI nodes
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
Since 16ccaf5bb5a5 ("pinctrl: sh-pfc: Accept standard function, pins and
groups properties") renesas pfc drivers accept generic "function", "pins"
and "groups" properties.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7793-gose.dts | 12 ++++++------
1 file changed, 6 insertions(+), 6 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7793-gose.dts b/arch/arm/boot/dts/r8a7793-gose.dts
index 90af18600124..dc311eba4444 100644
--- a/arch/arm/boot/dts/r8a7793-gose.dts
+++ b/arch/arm/boot/dts/r8a7793-gose.dts
@@ -346,18 +346,18 @@
};
sdhi0_pins: sd0 {
- renesas,groups = "sdhi0_data4", "sdhi0_ctrl";
- renesas,function = "sdhi0";
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
};
sdhi1_pins: sd1 {
- renesas,groups = "sdhi1_data4", "sdhi1_ctrl";
- renesas,function = "sdhi1";
+ groups = "sdhi1_data4", "sdhi1_ctrl";
+ function = "sdhi1";
};
sdhi2_pins: sd2 {
- renesas,groups = "sdhi2_data4", "sdhi2_ctrl";
- renesas,function = "sdhi2";
+ groups = "sdhi2_data4", "sdhi2_ctrl";
+ function = "sdhi2";
};
qspi_pins: qspi {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 16/29] ARM: dts: r8a7794: Fix W=1 dtc warnings
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,dvc/dvc at 0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,dvc/dvc at 1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,mix/mix at 0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,mix/mix at 1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ctu/ctu at 7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,src/src at 6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 0 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 1 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 2 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 3 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 4 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 5 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 6 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 7 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 8 has a unit name, but no reg property
Warning (unit_address_vs_reg): Node /sound at ec500000/rcar_sound,ssi/ssi at 9 has a unit name, but no reg property
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7794.dtsi | 58 +++++++++++++++++++++---------------------
1 file changed, 29 insertions(+), 29 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7794.dtsi b/arch/arm/boot/dts/r8a7794.dtsi
index 8cfc1385f58a..44ce62938417 100644
--- a/arch/arm/boot/dts/r8a7794.dtsi
+++ b/arch/arm/boot/dts/r8a7794.dtsi
@@ -1491,62 +1491,62 @@
status = "disabled";
rcar_sound,dvc {
- dvc0: dvc at 0 {
+ dvc0: dvc-0 {
dmas = <&audma0 0xbc>;
dma-names = "tx";
};
- dvc1: dvc at 1 {
+ dvc1: dvc-1 {
dmas = <&audma0 0xbe>;
dma-names = "tx";
};
};
rcar_sound,mix {
- mix0: mix at 0 { };
- mix1: mix at 1 { };
+ mix0: mix-0 { };
+ mix1: mix-1 { };
};
rcar_sound,ctu {
- ctu00: ctu at 0 { };
- ctu01: ctu at 1 { };
- ctu02: ctu at 2 { };
- ctu03: ctu at 3 { };
- ctu10: ctu at 4 { };
- ctu11: ctu at 5 { };
- ctu12: ctu at 6 { };
- ctu13: ctu at 7 { };
+ ctu00: ctu-0 { };
+ ctu01: ctu-1 { };
+ ctu02: ctu-2 { };
+ ctu03: ctu-3 { };
+ ctu10: ctu-4 { };
+ ctu11: ctu-5 { };
+ ctu12: ctu-6 { };
+ ctu13: ctu-7 { };
};
rcar_sound,src {
- src at 0 {
+ src-0 {
status = "disabled";
};
- src1: src at 1 {
+ src1: src-1 {
interrupts = <GIC_SPI 353 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x87>, <&audma0 0x9c>;
dma-names = "rx", "tx";
};
- src2: src at 2 {
+ src2: src-2 {
interrupts = <GIC_SPI 354 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x89>, <&audma0 0x9e>;
dma-names = "rx", "tx";
};
- src3: src at 3 {
+ src3: src-3 {
interrupts = <GIC_SPI 355 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8b>, <&audma0 0xa0>;
dma-names = "rx", "tx";
};
- src4: src at 4 {
+ src4: src-4 {
interrupts = <GIC_SPI 356 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8d>, <&audma0 0xb0>;
dma-names = "rx", "tx";
};
- src5: src at 5 {
+ src5: src-5 {
interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x8f>, <&audma0 0xb2>;
dma-names = "rx", "tx";
};
- src6: src at 6 {
+ src6: src-6 {
interrupts = <GIC_SPI 358 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x91>, <&audma0 0xb4>;
dma-names = "rx", "tx";
@@ -1554,61 +1554,61 @@
};
rcar_sound,ssi {
- ssi0: ssi at 0 {
+ ssi0: ssi-0 {
interrupts = <GIC_SPI 370 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x01>, <&audma0 0x02>,
<&audma0 0x15>, <&audma0 0x16>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi1: ssi at 1 {
+ ssi1: ssi-1 {
interrupts = <GIC_SPI 371 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x03>, <&audma0 0x04>,
<&audma0 0x49>, <&audma0 0x4a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi2: ssi at 2 {
+ ssi2: ssi-2 {
interrupts = <GIC_SPI 372 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x05>, <&audma0 0x06>,
<&audma0 0x63>, <&audma0 0x64>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi3: ssi at 3 {
+ ssi3: ssi-3 {
interrupts = <GIC_SPI 373 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x07>, <&audma0 0x08>,
<&audma0 0x6f>, <&audma0 0x70>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi4: ssi at 4 {
+ ssi4: ssi-4 {
interrupts = <GIC_SPI 374 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x09>, <&audma0 0x0a>,
<&audma0 0x71>, <&audma0 0x72>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi5: ssi at 5 {
+ ssi5: ssi-5 {
interrupts = <GIC_SPI 375 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0b>, <&audma0 0x0c>,
<&audma0 0x73>, <&audma0 0x74>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi6: ssi at 6 {
+ ssi6: ssi-6 {
interrupts = <GIC_SPI 376 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0d>, <&audma0 0x0e>,
<&audma0 0x75>, <&audma0 0x76>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi7: ssi at 7 {
+ ssi7: ssi-7 {
interrupts = <GIC_SPI 377 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x0f>, <&audma0 0x10>,
<&audma0 0x79>, <&audma0 0x7a>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi8: ssi at 8 {
+ ssi8: ssi-8 {
interrupts = <GIC_SPI 378 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x11>, <&audma0 0x12>,
<&audma0 0x7b>, <&audma0 0x7c>;
dma-names = "rx", "tx", "rxu", "txu";
};
- ssi9: ssi at 9 {
+ ssi9: ssi-9 {
interrupts = <GIC_SPI 379 IRQ_TYPE_LEVEL_HIGH>;
dmas = <&audma0 0x13>, <&audma0 0x14>,
<&audma0 0x7d>, <&audma0 0x7e>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 17/29] ARM: dts: r7s72100: add sdhi to device tree
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r7s72100.dtsi | 26 ++++++++++++++++++++++++++
1 file changed, 26 insertions(+)
diff --git a/arch/arm/boot/dts/r7s72100.dtsi b/arch/arm/boot/dts/r7s72100.dtsi
index eab06701ef11..3dd427d68c83 100644
--- a/arch/arm/boot/dts/r7s72100.dtsi
+++ b/arch/arm/boot/dts/r7s72100.dtsi
@@ -470,4 +470,30 @@
bus-width = <8>;
status = "disabled";
};
+
+ sdhi0: sd at e804e000 {
+ compatible = "renesas,sdhi-r7s72100";
+ reg = <0xe804e000 0x100>;
+ interrupts = <GIC_SPI 270 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 271 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 272 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mstp12_clks R7S72100_CLK_SDHI0>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ status = "disabled";
+ };
+
+ sdhi1: sd at e804e800 {
+ compatible = "renesas,sdhi-r7s72100";
+ reg = <0xe804e800 0x100>;
+ interrupts = <GIC_SPI 273 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 274 IRQ_TYPE_LEVEL_HIGH
+ GIC_SPI 275 IRQ_TYPE_LEVEL_HIGH>;
+
+ clocks = <&mstp12_clks R7S72100_CLK_SDHI1>;
+ cap-sd-highspeed;
+ cap-sdio-irq;
+ status = "disabled";
+ };
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 18/29] ARM: dts: rskrza1: add sdhi1 DT support
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Chris Brandt <chris.brandt@renesas.com>
Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r7s72100-rskrza1.dts | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/r7s72100-rskrza1.dts b/arch/arm/boot/dts/r7s72100-rskrza1.dts
index e5dea5bb4032..dd4418195ca6 100644
--- a/arch/arm/boot/dts/r7s72100-rskrza1.dts
+++ b/arch/arm/boot/dts/r7s72100-rskrza1.dts
@@ -56,6 +56,11 @@
};
};
+&sdhi1 {
+ bus-width = <4>;
+ status = "okay";
+};
+
&scif2 {
status = "okay";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 19/29] ARM: dts: lager: Add entries for VIN HDMI input support
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: William Towle <william.towle@codethink.co.uk>
Add DT entries for vin0, vin0_pins, and adv7612.
Sets the 'default-input' property for ADV7612, enabling image and video
capture without the need to have userspace specifying routing.
Signed-off-by: William Towle <william.towle@codethink.co.uk>
Signed-off-by: Rob Taylor <rob.taylor@codethink.co.uk>
[uli: added interrupt, renamed endpoint, merged default-input]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7790-lager.dts | 66 +++++++++++++++++++++++++++++++++++--
1 file changed, 64 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7790-lager.dts b/arch/arm/boot/dts/r8a7790-lager.dts
index 52b56fcaddf2..434268262d88 100644
--- a/arch/arm/boot/dts/r8a7790-lager.dts
+++ b/arch/arm/boot/dts/r8a7790-lager.dts
@@ -231,12 +231,23 @@
};
};
+ hdmi-in {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&adv7612_in>;
+ };
+ };
+ };
+
hdmi-out {
compatible = "hdmi-connector";
type = "a";
port {
- hdmi_con: endpoint {
+ hdmi_con_out: endpoint {
remote-endpoint = <&adv7511_out>;
};
};
@@ -427,6 +438,11 @@
function = "usb2";
};
+ vin0_pins: vin0 {
+ groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
+ function = "vin0";
+ };
+
vin1_pins: vin1 {
groups = "vin1_data8", "vin1_clk";
function = "vin1";
@@ -646,7 +662,34 @@
port at 1 {
reg = <1>;
adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
+ remote-endpoint = <&hdmi_con_out>;
+ };
+ };
+ };
+ };
+
+ hdmi-in at 4c {
+ compatible = "adi,adv7612";
+ reg = <0x4c>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <20 IRQ_TYPE_LEVEL_LOW>;
+ default-input = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7612_in: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ adv7612_out: endpoint {
+ remote-endpoint = <&vin0ep2>;
};
};
};
@@ -722,6 +765,25 @@
status = "okay";
};
+/* HDMI video input */
+&vin0 {
+ pinctrl-0 = <&vin0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ port {
+ vin0ep2: endpoint {
+ remote-endpoint = <&adv7612_out>;
+ bus-width = <24>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ data-active = <1>;
+ };
+ };
+};
+
/* composite video input */
&vin1 {
pinctrl-0 = <&vin1_pins>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 20/29] ARM: dts: koelsch: add HDMI input
From: Simon Horman @ 2016-11-04 9:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1478252308.git.horms+renesas@verge.net.au>
From: Hans Verkuil <hverkuil@xs4all.nl>
Add support in the dts for the HDMI input. Based on the Lager dts
patch from Ulrich Hecht.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
[uli: removed "renesas," prefixes from pfc nodes]
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/boot/dts/r8a7791-koelsch.dts | 68 +++++++++++++++++++++++++++++++++--
1 file changed, 66 insertions(+), 2 deletions(-)
diff --git a/arch/arm/boot/dts/r8a7791-koelsch.dts b/arch/arm/boot/dts/r8a7791-koelsch.dts
index f17bfa000f73..c457b43deb7d 100644
--- a/arch/arm/boot/dts/r8a7791-koelsch.dts
+++ b/arch/arm/boot/dts/r8a7791-koelsch.dts
@@ -265,12 +265,23 @@
};
};
+ hdmi-in {
+ compatible = "hdmi-connector";
+ type = "a";
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&adv7612_in>;
+ };
+ };
+ };
+
hdmi-out {
compatible = "hdmi-connector";
type = "a";
port {
- hdmi_con: endpoint {
+ hdmi_con_out: endpoint {
remote-endpoint = <&adv7511_out>;
};
};
@@ -414,6 +425,11 @@
function = "usb1";
};
+ vin0_pins: vin0 {
+ groups = "vin0_data24", "vin0_sync", "vin0_clkenb", "vin0_clk";
+ function = "vin0";
+ };
+
vin1_pins: vin1 {
groups = "vin1_data8", "vin1_clk";
function = "vin1";
@@ -617,7 +633,34 @@
port at 1 {
reg = <1>;
adv7511_out: endpoint {
- remote-endpoint = <&hdmi_con>;
+ remote-endpoint = <&hdmi_con_out>;
+ };
+ };
+ };
+ };
+
+ hdmi-in at 4c {
+ compatible = "adi,adv7612";
+ reg = <0x4c>;
+ interrupt-parent = <&gpio4>;
+ interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
+ default-input = <0>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port at 0 {
+ reg = <0>;
+ adv7612_in: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+ };
+
+ port at 2 {
+ reg = <2>;
+ adv7612_out: endpoint {
+ remote-endpoint = <&vin0ep2>;
};
};
};
@@ -699,6 +742,27 @@
cpu0-supply = <&vdd_dvfs>;
};
+/* HDMI video input */
+&vin0 {
+ status = "okay";
+ pinctrl-0 = <&vin0_pins>;
+ pinctrl-names = "default";
+
+ port {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ vin0ep2: endpoint {
+ remote-endpoint = <&adv7612_out>;
+ bus-width = <24>;
+ hsync-active = <0>;
+ vsync-active = <0>;
+ pclk-sample = <1>;
+ data-active = <1>;
+ };
+ };
+};
+
/* composite video input */
&vin1 {
status = "okay";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox