* [PATCH v3 1/1] KVM: ARM64: Fix the issues when guest PMCCFILTR is configured
From: Marc Zyngier @ 2016-11-17 13:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161117133039.GH22855@arm.com>
On 17/11/16 13:30, Will Deacon wrote:
> On Wed, Nov 16, 2016 at 11:09:20AM -0600, Wei Huang wrote:
>> KVM calls kvm_pmu_set_counter_event_type() when PMCCFILTR is configured.
>> But this function can't deals with PMCCFILTR correctly because the evtCount
>> bits of PMCCFILTR, which is reserved 0, conflits with the SW_INCR event
>> type of other PMXEVTYPER<n> registers. To fix it, when eventsel == 0, this
>> function shouldn't return immediately; instead it needs to check further
>> if select_idx is ARMV8_PMU_CYCLE_IDX.
>>
>> Another issue is that KVM shouldn't copy the eventsel bits of PMCCFILTER
>> blindly to attr.config. Instead it ought to convert the request to the
>> "cpu cycle" event type (i.e. 0x11).
>>
>> To support this patch and to prevent duplicated definitions, a limited
>> set of ARMv8 perf event types were relocated from perf_event.c to
>> asm/perf_event.h.
>>
>> Signed-off-by: Wei Huang <wei@redhat.com>
>> ---
>> arch/arm64/include/asm/perf_event.h | 10 +++++++++-
>> arch/arm64/kernel/perf_event.c | 10 +---------
>> virt/kvm/arm/pmu.c | 8 +++++---
>> 3 files changed, 15 insertions(+), 13 deletions(-)
>
> Acked-by: Will Deacon <will.deacon@arm.com>
>
> I'm assuming this will go via kvm-arm.
Yup, I'll take it. Thanks.
M.
--
Jazz is not dead. It just smells funny...
^ permalink raw reply
* [PATCH] ARM: dt: imx31: fix AVIC base address
From: Fabio Estevam @ 2016-11-17 13:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161117013051.29381-1-vz@mleia.com>
On Wed, Nov 16, 2016 at 11:30 PM, Vladimir Zapolskiy <vz@mleia.com> wrote:
> From: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
>
> On i.MX31 AVIC interrupt controller base address is at 0x68000000.
>
> The problem was shadowed by the AVIC driver, which takes the correct
> base address from a SoC specific header file.
>
> Fixes: d2a37b3d91f4 ("ARM i.MX31: Add devicetree support")
> Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Yes, this is what the Reference Manual states, thanks.
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
^ permalink raw reply
* [RFC PATCH] of: base: add support to get machine model name
From: Arnd Bergmann @ 2016-11-17 13:50 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479383450-19183-1-git-send-email-sudeep.holla@arm.com>
On Thursday, November 17, 2016 11:50:50 AM CET Sudeep Holla wrote:
> Currently platforms/drivers needing to get the machine model name are
> replicating the same snippet of code. In some case, the OF reference
> counting is either missing or incorrect.
>
> This patch adds support to read the machine model name either using
> the "model" or the "compatible" property in the device tree root node.
>
> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
I like the idea. One small comment:
> +int of_machine_get_model_name(const char **model)
> +{
> + int error;
> + struct device_node *root;
> +
> + root = of_find_node_by_path("/");
> + if (!root)
> + return -EINVAL;
The global of_root variable points ot this already, and is defined
in the same file, so I think we can just skip the lookup.
Arnd
^ permalink raw reply
* [PATCH 1/4] ARM: shmobile: r8a7745: add power domain index macros
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479389981.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Add macros usable by the device tree sources to reference R8A7745 SYSC power
domains by index.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
include/dt-bindings/power/r8a7745-sysc.h | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)
create mode 100644 include/dt-bindings/power/r8a7745-sysc.h
diff --git a/include/dt-bindings/power/r8a7745-sysc.h b/include/dt-bindings/power/r8a7745-sysc.h
new file mode 100644
index 000000000000..1844c1171c04
--- /dev/null
+++ b/include/dt-bindings/power/r8a7745-sysc.h
@@ -0,0 +1,25 @@
+/*
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+#ifndef __DT_BINDINGS_POWER_R8A7745_SYSC_H__
+#define __DT_BINDINGS_POWER_R8A7745_SYSC_H__
+
+/*
+ * These power domain indices match the numbers of the interrupt bits
+ * representing the power areas in the various Interrupt Registers
+ * (e.g. SYSCISR, Interrupt Status Register)
+ */
+
+#define R8A7745_PD_CA7_CPU0 5
+#define R8A7745_PD_CA7_CPU1 6
+#define R8A7745_PD_SGX 20
+#define R8A7745_PD_CA7_SCU 21
+
+/* Always-on power area */
+#define R8A7745_PD_ALWAYS_ON 32
+
+#endif /* __DT_BINDINGS_POWER_R8A7745_SYSC_H__ */
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [GIT PULL] Second Round of Renesas ARM Based SoC Drivers Updates for v4.10
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
Hi Olof, Hi Kevin, Hi Arnd,
Please consider these second round of Renesas ARM based SoC drivers updates for v4.10.
This pull request is based on a merge of:
* The previous round of such requests, tagged as renesas-drivers-for-v4.10,
which you have already pulled.
* The soc-device-match-tag1 tag of Geert Uytterhoeven's renesas-driver's tree.
This is included to provide core soc_device_match() infrastructure which
is a dependency of identifying SoC and registering with SoC bus.
The following changes since commit 437c4eeb0bd4c1d68817be997716f52b8c22a9c3:
Merge tag 'soc-device-match-tag1' of https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers into HEAD (2016-11-15 14:12:57 +0100)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-drivers2-for-v4.10
for you to fetch changes up to 63ee9e2ba47dbdb42156c9b940515cfd49e78c91:
soc: renesas: Identify SoC and register with the SoC bus (2016-11-17 14:37:20 +0100)
----------------------------------------------------------------
Second Round of Renesas ARM Based SoC Drivers Updates for v4.10
* Identify SoC and register with the SoC bus
* Add support for the r8a7745 SoC to rcar-sysc
----------------------------------------------------------------
Geert Uytterhoeven (2):
ARM: shmobile: Document DT bindings for Product Register
soc: renesas: Identify SoC and register with the SoC bus
Sergei Shtylyov (2):
ARM: shmobile: r8a7745: add power domain index macros
soc: renesas: rcar-sysc: add R8A7745 support
Documentation/devicetree/bindings/arm/shmobile.txt | 18 ++
.../bindings/power/renesas,rcar-sysc.txt | 1 +
arch/arm/mach-shmobile/Kconfig | 1 +
arch/arm64/Kconfig.platforms | 1 +
drivers/soc/renesas/Makefile | 3 +
drivers/soc/renesas/r8a7745-sysc.c | 32 +++
drivers/soc/renesas/rcar-sysc.c | 3 +
drivers/soc/renesas/rcar-sysc.h | 1 +
drivers/soc/renesas/renesas-soc.c | 257 +++++++++++++++++++++
include/dt-bindings/power/r8a7745-sysc.h | 25 ++
10 files changed, 342 insertions(+)
create mode 100644 drivers/soc/renesas/r8a7745-sysc.c
create mode 100644 drivers/soc/renesas/renesas-soc.c
create mode 100644 include/dt-bindings/power/r8a7745-sysc.h
^ permalink raw reply
* [PATCH 2/4] soc: renesas: rcar-sysc: add R8A7745 support
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479389981.git.horms+renesas@verge.net.au>
From: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Add support for RZ/G1E (R8A7745) SoC power areas to the R-Car SYSC driver.
Based on the original (and large) patch by Dmitry Shifrin
<dmitry.shifrin@cogentembedded.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
.../bindings/power/renesas,rcar-sysc.txt | 1 +
drivers/soc/renesas/Makefile | 1 +
drivers/soc/renesas/r8a7745-sysc.c | 32 ++++++++++++++++++++++
drivers/soc/renesas/rcar-sysc.c | 3 ++
drivers/soc/renesas/rcar-sysc.h | 1 +
5 files changed, 38 insertions(+)
create mode 100644 drivers/soc/renesas/r8a7745-sysc.c
diff --git a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
index c16ec1866ac4..d91715bc8d52 100644
--- a/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
+++ b/Documentation/devicetree/bindings/power/renesas,rcar-sysc.txt
@@ -8,6 +8,7 @@ and various coprocessors.
Required properties:
- compatible: Must contain exactly one of the following:
- "renesas,r8a7743-sysc" (RZ/G1M)
+ - "renesas,r8a7745-sysc" (RZ/G1E)
- "renesas,r8a7779-sysc" (R-Car H1)
- "renesas,r8a7790-sysc" (R-Car H2)
- "renesas,r8a7791-sysc" (R-Car M2-W)
diff --git a/drivers/soc/renesas/Makefile b/drivers/soc/renesas/Makefile
index 9e0bb329594c..e2249f01b2de 100644
--- a/drivers/soc/renesas/Makefile
+++ b/drivers/soc/renesas/Makefile
@@ -1,4 +1,5 @@
obj-$(CONFIG_ARCH_R8A7743) += rcar-sysc.o r8a7743-sysc.o
+obj-$(CONFIG_ARCH_R8A7745) += rcar-sysc.o r8a7745-sysc.o
obj-$(CONFIG_ARCH_R8A7779) += rcar-sysc.o r8a7779-sysc.o
obj-$(CONFIG_ARCH_R8A7790) += rcar-sysc.o r8a7790-sysc.o
obj-$(CONFIG_ARCH_R8A7791) += rcar-sysc.o r8a7791-sysc.o
diff --git a/drivers/soc/renesas/r8a7745-sysc.c b/drivers/soc/renesas/r8a7745-sysc.c
new file mode 100644
index 000000000000..d17887c08aa1
--- /dev/null
+++ b/drivers/soc/renesas/r8a7745-sysc.c
@@ -0,0 +1,32 @@
+/*
+ * Renesas RZ/G1E System Controller
+ *
+ * Copyright (C) 2016 Cogent Embedded Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation; of the License.
+ */
+
+#include <linux/bug.h>
+#include <linux/kernel.h>
+
+#include <dt-bindings/power/r8a7745-sysc.h>
+
+#include "rcar-sysc.h"
+
+static const struct rcar_sysc_area r8a7745_areas[] __initconst = {
+ { "always-on", 0, 0, R8A7745_PD_ALWAYS_ON, -1, PD_ALWAYS_ON },
+ { "ca7-scu", 0x100, 0, R8A7745_PD_CA7_SCU, R8A7745_PD_ALWAYS_ON,
+ PD_SCU },
+ { "ca7-cpu0", 0x1c0, 0, R8A7745_PD_CA7_CPU0, R8A7745_PD_CA7_SCU,
+ PD_CPU_NOCR },
+ { "ca7-cpu1", 0x1c0, 1, R8A7745_PD_CA7_CPU1, R8A7745_PD_CA7_SCU,
+ PD_CPU_NOCR },
+ { "sgx", 0xc0, 0, R8A7745_PD_SGX, R8A7745_PD_ALWAYS_ON },
+};
+
+const struct rcar_sysc_info r8a7745_sysc_info __initconst = {
+ .areas = r8a7745_areas,
+ .num_areas = ARRAY_SIZE(r8a7745_areas),
+};
diff --git a/drivers/soc/renesas/rcar-sysc.c b/drivers/soc/renesas/rcar-sysc.c
index 71acd45b13f0..225c35c79d9a 100644
--- a/drivers/soc/renesas/rcar-sysc.c
+++ b/drivers/soc/renesas/rcar-sysc.c
@@ -278,6 +278,9 @@ static const struct of_device_id rcar_sysc_matches[] = {
#ifdef CONFIG_ARCH_R8A7743
{ .compatible = "renesas,r8a7743-sysc", .data = &r8a7743_sysc_info },
#endif
+#ifdef CONFIG_ARCH_R8A7745
+ { .compatible = "renesas,r8a7745-sysc", .data = &r8a7745_sysc_info },
+#endif
#ifdef CONFIG_ARCH_R8A7779
{ .compatible = "renesas,r8a7779-sysc", .data = &r8a7779_sysc_info },
#endif
diff --git a/drivers/soc/renesas/rcar-sysc.h b/drivers/soc/renesas/rcar-sysc.h
index 8ab9ca8a825a..f6e842e2976e 100644
--- a/drivers/soc/renesas/rcar-sysc.h
+++ b/drivers/soc/renesas/rcar-sysc.h
@@ -51,6 +51,7 @@ struct rcar_sysc_info {
};
extern const struct rcar_sysc_info r8a7743_sysc_info;
+extern const struct rcar_sysc_info r8a7745_sysc_info;
extern const struct rcar_sysc_info r8a7779_sysc_info;
extern const struct rcar_sysc_info r8a7790_sysc_info;
extern const struct rcar_sysc_info r8a7791_sysc_info;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 3/4] ARM: shmobile: Document DT bindings for Product Register
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479389981.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Add device tree binding documentation for the Product Register (PRR),
which provides product and revision information on most Renesas ARM
SoCs.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
Documentation/devicetree/bindings/arm/shmobile.txt | 18 ++++++++++++++++++
1 file changed, 18 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 2f0b7169f132..23c77315fdac 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -75,3 +75,21 @@ Boards:
compatible = "renesas,silk", "renesas,r8a7794"
- Wheat
compatible = "renesas,wheat", "renesas,r8a7792"
+
+
+Most Renesas ARM SoCs have a Product Register that allows to retrieve SoC
+product and revision information. If present, a device node for this register
+should be added.
+
+Required properties:
+ - compatible: Must be "renesas,prr".
+ - reg: Base address and length of the register block.
+
+
+Examples
+--------
+
+ prr: chipid at ff000044 {
+ compatible = "renesas,prr";
+ reg = <0 0xff000044 0 4>;
+ };
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 4/4] soc: renesas: Identify SoC and register with the SoC bus
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479389981.git.horms+renesas@verge.net.au>
From: Geert Uytterhoeven <geert+renesas@glider.be>
Identify the SoC type and revision, and register this information with
the SoC bus, so it is available under /sys/devices/soc0/, and can be
checked where needed using soc_device_match().
Identification is done using the Product Register or Common Chip Code
Register, as declared in DT (PRR only for now), or using a hardcoded
fallback if missing.
Example:
Detected Renesas R-Car Gen2 r8a7791 ES1.0
...
# cat /sys/devices/soc0/{machine,family,soc_id,revision}
Koelsch
R-Car Gen2
r8a7791
ES1.0
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm/mach-shmobile/Kconfig | 1 +
arch/arm64/Kconfig.platforms | 1 +
drivers/soc/renesas/Makefile | 2 +
drivers/soc/renesas/renesas-soc.c | 257 ++++++++++++++++++++++++++++++++++++++
4 files changed, 261 insertions(+)
create mode 100644 drivers/soc/renesas/renesas-soc.c
diff --git a/arch/arm/mach-shmobile/Kconfig b/arch/arm/mach-shmobile/Kconfig
index 09817bae4558..ebab13e8afa1 100644
--- a/arch/arm/mach-shmobile/Kconfig
+++ b/arch/arm/mach-shmobile/Kconfig
@@ -40,6 +40,7 @@ menuconfig ARCH_RENESAS
select ARCH_DMA_ADDR_T_64BIT if ARM_LPAE
select NO_IOPORT_MAP
select PINCTRL
+ select SOC_BUS
select GPIOLIB
select ZONE_DMA if ARM_LPAE
diff --git a/arch/arm64/Kconfig.platforms b/arch/arm64/Kconfig.platforms
index cfbdf02ef566..72f4eac5cbbc 100644
--- a/arch/arm64/Kconfig.platforms
+++ b/arch/arm64/Kconfig.platforms
@@ -143,6 +143,7 @@ config ARCH_RENESAS
select PM
select PM_GENERIC_DOMAINS
select RENESAS_IRQC
+ select SOC_BUS
help
This enables support for the ARMv8 based Renesas SoCs.
diff --git a/drivers/soc/renesas/Makefile b/drivers/soc/renesas/Makefile
index e2249f01b2de..91c42b34705f 100644
--- a/drivers/soc/renesas/Makefile
+++ b/drivers/soc/renesas/Makefile
@@ -1,3 +1,5 @@
+obj-$(CONFIG_SOC_BUS) += renesas-soc.o
+
obj-$(CONFIG_ARCH_R8A7743) += rcar-sysc.o r8a7743-sysc.o
obj-$(CONFIG_ARCH_R8A7745) += rcar-sysc.o r8a7745-sysc.o
obj-$(CONFIG_ARCH_R8A7779) += rcar-sysc.o r8a7779-sysc.o
diff --git a/drivers/soc/renesas/renesas-soc.c b/drivers/soc/renesas/renesas-soc.c
new file mode 100644
index 000000000000..330960312296
--- /dev/null
+++ b/drivers/soc/renesas/renesas-soc.c
@@ -0,0 +1,257 @@
+/*
+ * Renesas SoC Identification
+ *
+ * Copyright (C) 2014-2016 Glider bvba
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; version 2 of the License.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/of_address.h>
+#include <linux/slab.h>
+#include <linux/string.h>
+#include <linux/sys_soc.h>
+
+
+struct renesas_family {
+ const char name[16];
+ u32 reg; /* CCCR or PRR, if not in DT */
+};
+
+static const struct renesas_family fam_rcar_gen1 __initconst __maybe_unused = {
+ .name = "R-Car Gen1",
+ .reg = 0xff000044, /* PRR (Product Register) */
+};
+
+static const struct renesas_family fam_rcar_gen2 __initconst __maybe_unused = {
+ .name = "R-Car Gen2",
+ .reg = 0xff000044, /* PRR (Product Register) */
+};
+
+static const struct renesas_family fam_rcar_gen3 __initconst __maybe_unused = {
+ .name = "R-Car Gen3",
+ .reg = 0xfff00044, /* PRR (Product Register) */
+};
+
+static const struct renesas_family fam_rmobile __initconst __maybe_unused = {
+ .name = "R-Mobile",
+ .reg = 0xe600101c, /* CCCR (Common Chip Code Register) */
+};
+
+static const struct renesas_family fam_rza __initconst __maybe_unused = {
+ .name = "RZ/A",
+};
+
+static const struct renesas_family fam_rzg __initconst __maybe_unused = {
+ .name = "RZ/G",
+ .reg = 0xff000044, /* PRR (Product Register) */
+};
+
+static const struct renesas_family fam_shmobile __initconst __maybe_unused = {
+ .name = "SH-Mobile",
+ .reg = 0xe600101c, /* CCCR (Common Chip Code Register) */
+};
+
+
+struct renesas_soc {
+ const struct renesas_family *family;
+ u8 id;
+};
+
+static const struct renesas_soc soc_rz_a1h __initconst __maybe_unused = {
+ .family = &fam_rza,
+};
+
+static const struct renesas_soc soc_rmobile_ape6 __initconst __maybe_unused = {
+ .family = &fam_rmobile,
+ .id = 0x3f,
+};
+
+static const struct renesas_soc soc_rmobile_a1 __initconst __maybe_unused = {
+ .family = &fam_rmobile,
+ .id = 0x40,
+};
+
+static const struct renesas_soc soc_rz_g1m __initconst __maybe_unused = {
+ .family = &fam_rzg,
+ .id = 0x47,
+};
+
+static const struct renesas_soc soc_rz_g1e __initconst __maybe_unused = {
+ .family = &fam_rzg,
+ .id = 0x4c,
+};
+
+static const struct renesas_soc soc_rcar_m1a __initconst __maybe_unused = {
+ .family = &fam_rcar_gen1,
+};
+
+static const struct renesas_soc soc_rcar_h1 __initconst __maybe_unused = {
+ .family = &fam_rcar_gen1,
+ .id = 0x3b,
+};
+
+static const struct renesas_soc soc_rcar_h2 __initconst __maybe_unused = {
+ .family = &fam_rcar_gen2,
+ .id = 0x45,
+};
+
+static const struct renesas_soc soc_rcar_m2_w __initconst __maybe_unused = {
+ .family = &fam_rcar_gen2,
+ .id = 0x47,
+};
+
+static const struct renesas_soc soc_rcar_v2h __initconst __maybe_unused = {
+ .family = &fam_rcar_gen2,
+ .id = 0x4a,
+};
+
+static const struct renesas_soc soc_rcar_m2_n __initconst __maybe_unused = {
+ .family = &fam_rcar_gen2,
+ .id = 0x4b,
+};
+
+static const struct renesas_soc soc_rcar_e2 __initconst __maybe_unused = {
+ .family = &fam_rcar_gen2,
+ .id = 0x4c,
+};
+
+static const struct renesas_soc soc_rcar_h3 __initconst __maybe_unused = {
+ .family = &fam_rcar_gen3,
+ .id = 0x4f,
+};
+
+static const struct renesas_soc soc_rcar_m3_w __initconst __maybe_unused = {
+ .family = &fam_rcar_gen3,
+ .id = 0x52,
+};
+
+static const struct renesas_soc soc_shmobile_ag5 __initconst __maybe_unused = {
+ .family = &fam_shmobile,
+ .id = 0x37,
+};
+
+
+static const struct of_device_id renesas_socs[] __initconst = {
+#ifdef CONFIG_ARCH_R7S72100
+ { .compatible = "renesas,r7s72100", .data = &soc_rz_a1h },
+#endif
+#ifdef CONFIG_ARCH_R8A73A4
+ { .compatible = "renesas,r8a73a4", .data = &soc_rmobile_ape6 },
+#endif
+#ifdef CONFIG_ARCH_R8A7740
+ { .compatible = "renesas,r8a7740", .data = &soc_rmobile_a1 },
+#endif
+#ifdef CONFIG_ARCH_R8A7743
+ { .compatible = "renesas,r8a7743", .data = &soc_rz_g1m },
+#endif
+#ifdef CONFIG_ARCH_R8A7745
+ { .compatible = "renesas,r8a7745", .data = &soc_rz_g1e },
+#endif
+#ifdef CONFIG_ARCH_R8A7778
+ { .compatible = "renesas,r8a7778", .data = &soc_rcar_m1a },
+#endif
+#ifdef CONFIG_ARCH_R8A7779
+ { .compatible = "renesas,r8a7779", .data = &soc_rcar_h1 },
+#endif
+#ifdef CONFIG_ARCH_R8A7790
+ { .compatible = "renesas,r8a7790", .data = &soc_rcar_h2 },
+#endif
+#ifdef CONFIG_ARCH_R8A7791
+ { .compatible = "renesas,r8a7791", .data = &soc_rcar_m2_w },
+#endif
+#ifdef CONFIG_ARCH_R8A7792
+ { .compatible = "renesas,r8a7792", .data = &soc_rcar_v2h },
+#endif
+#ifdef CONFIG_ARCH_R8A7793
+ { .compatible = "renesas,r8a7793", .data = &soc_rcar_m2_n },
+#endif
+#ifdef CONFIG_ARCH_R8A7794
+ { .compatible = "renesas,r8a7794", .data = &soc_rcar_e2 },
+#endif
+#ifdef CONFIG_ARCH_R8A7795
+ { .compatible = "renesas,r8a7795", .data = &soc_rcar_h3 },
+#endif
+#ifdef CONFIG_ARCH_R8A7796
+ { .compatible = "renesas,r8a7796", .data = &soc_rcar_m3_w },
+#endif
+#ifdef CONFIG_ARCH_SH73A0
+ { .compatible = "renesas,sh73a0", .data = &soc_shmobile_ag5 },
+#endif
+ { /* sentinel */ }
+};
+
+static int __init renesas_soc_init(void)
+{
+ struct soc_device_attribute *soc_dev_attr;
+ const struct renesas_family *family;
+ const struct of_device_id *match;
+ const struct renesas_soc *soc;
+ void __iomem *chipid = NULL;
+ struct soc_device *soc_dev;
+ struct device_node *np;
+ unsigned int product;
+
+ match = of_match_node(renesas_socs, of_root);
+ if (!match)
+ return -ENODEV;
+
+ soc = match->data;
+ family = soc->family;
+
+ /* Try PRR first, then hardcoded fallback */
+ np = of_find_compatible_node(NULL, NULL, "renesas,prr");
+ if (np) {
+ chipid = of_iomap(np, 0);
+ of_node_put(np);
+ } else if (soc->id) {
+ chipid = ioremap(family->reg, 4);
+ }
+ if (chipid) {
+ product = readl(chipid);
+ iounmap(chipid);
+ if (soc->id && ((product >> 8) & 0xff) != soc->id) {
+ pr_warn("SoC mismatch (product = 0x%x)\n", product);
+ return -ENODEV;
+ }
+ }
+
+ soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
+ if (!soc_dev_attr)
+ return -ENOMEM;
+
+ np = of_find_node_by_path("/");
+ of_property_read_string(np, "model", &soc_dev_attr->machine);
+ of_node_put(np);
+
+ soc_dev_attr->family = kstrdup_const(family->name, GFP_KERNEL);
+ soc_dev_attr->soc_id = kstrdup_const(strchr(match->compatible, ',') + 1,
+ GFP_KERNEL);
+ if (chipid)
+ soc_dev_attr->revision = kasprintf(GFP_KERNEL, "ES%u.%u",
+ ((product >> 4) & 0x0f) + 1,
+ product & 0xf);
+
+ pr_info("Detected Renesas %s %s %s\n", soc_dev_attr->family,
+ soc_dev_attr->soc_id, soc_dev_attr->revision ?: "");
+
+ soc_dev = soc_device_register(soc_dev_attr);
+ if (IS_ERR(soc_dev)) {
+ kfree(soc_dev_attr->revision);
+ kfree_const(soc_dev_attr->soc_id);
+ kfree_const(soc_dev_attr->family);
+ kfree(soc_dev_attr);
+ return PTR_ERR(soc_dev);
+ }
+
+ return 0;
+}
+core_initcall(renesas_soc_init);
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 01/18] arm64: dts: r8a7796: add I2C support
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 94 ++++++++++++++++++++++++++++++++
1 file changed, 94 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index f9cb7796ad49..2e940ff61378 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -17,6 +17,16 @@
#address-cells = <2>;
#size-cells = <2>;
+ aliases {
+ i2c0 = &i2c0;
+ i2c1 = &i2c1;
+ i2c2 = &i2c2;
+ i2c3 = &i2c3;
+ i2c4 = &i2c4;
+ i2c5 = &i2c5;
+ i2c6 = &i2c6;
+ };
+
psci {
compatible = "arm,psci-0.2";
method = "smc";
@@ -239,6 +249,90 @@
#power-domain-cells = <1>;
};
+ i2c0: i2c at e6500000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe6500000 0 0x40>;
+ interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 931>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <110>;
+ status = "disabled";
+ };
+
+ i2c1: i2c at e6508000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe6508000 0 0x40>;
+ interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 930>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <6>;
+ status = "disabled";
+ };
+
+ i2c2: i2c at e6510000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe6510000 0 0x40>;
+ interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 929>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <6>;
+ status = "disabled";
+ };
+
+ i2c3: i2c at e66d0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe66d0000 0 0x40>;
+ interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 928>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <110>;
+ status = "disabled";
+ };
+
+ i2c4: i2c at e66d8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe66d8000 0 0x40>;
+ interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 927>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <110>;
+ status = "disabled";
+ };
+
+ i2c5: i2c at e66e0000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe66e0000 0 0x40>;
+ interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 919>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <110>;
+ status = "disabled";
+ };
+
+ i2c6: i2c at e66e8000 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "renesas,i2c-r8a7796";
+ reg = <0 0xe66e8000 0 0x40>;
+ interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD 918>;
+ power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ i2c-scl-internal-delay-ns = <6>;
+ status = "disabled";
+ };
+
scif2: serial at e6e88000 {
compatible = "renesas,scif-r8a7796",
"renesas,rcar-gen3-scif", "renesas,scif";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 02/18] arm64: dts: r8a7796: Enable I2C DMA
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796.dtsi b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
index 2e940ff61378..9599f5691099 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7796.dtsi
@@ -257,6 +257,9 @@
interrupts = <GIC_SPI 287 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 931>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac1 0x91>, <&dmac1 0x90>,
+ <&dmac2 0x91>, <&dmac2 0x90>;
+ dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -269,6 +272,9 @@
interrupts = <GIC_SPI 288 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 930>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac1 0x93>, <&dmac1 0x92>,
+ <&dmac2 0x93>, <&dmac2 0x92>;
+ dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -281,6 +287,9 @@
interrupts = <GIC_SPI 286 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 929>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac1 0x95>, <&dmac1 0x94>,
+ <&dmac2 0x95>, <&dmac2 0x94>;
+ dma-names = "tx", "rx", "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
@@ -293,6 +302,8 @@
interrupts = <GIC_SPI 290 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 928>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x97>, <&dmac0 0x96>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -305,6 +316,8 @@
interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 927>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x99>, <&dmac0 0x98>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -317,6 +330,8 @@
interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 919>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x9b>, <&dmac0 0x9a>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <110>;
status = "disabled";
};
@@ -329,6 +344,8 @@
interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>;
clocks = <&cpg CPG_MOD 918>;
power-domains = <&sysc R8A7796_PD_ALWAYS_ON>;
+ dmas = <&dmac0 0x9d>, <&dmac0 0x9c>;
+ dma-names = "tx", "rx";
i2c-scl-internal-delay-ns = <6>;
status = "disabled";
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 03/18] arm64: dts: r8a7796: salvator-x: enable I2C
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
index a9c296b1e1b7..f35e96ca7d60 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts
@@ -111,6 +111,11 @@
function = "scif_clk";
};
+ i2c2_pins: i2c2 {
+ groups = "i2c2_a";
+ function = "i2c2";
+ };
+
sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
@@ -208,6 +213,13 @@
status = "okay";
};
+&i2c2 {
+ pinctrl-0 = <&i2c2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
+
&wdt0 {
timeout-sec = <60>;
status = "okay";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 04/18] arm64: dts: h3ulcb: update documentation with official board name
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This updates H3ULCB Device tree bindings Documentation with
official board name
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
Documentation/devicetree/bindings/arm/shmobile.txt | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 23c77315fdac..968ae9a05440 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -49,7 +49,7 @@ Boards:
compatible = "renesas,genmai", "renesas,r7s72100"
- Gose
compatible = "renesas,gose", "renesas,r8a7793"
- - H3ULCB (RTP0RC7795SKB00010S)
+ - H3ULCB (R-Car Starter Kit Premier, RTP0RC7795SKB00010S)
compatible = "renesas,h3ulcb", "renesas,r8a7795";
- Henninger
compatible = "renesas,henninger", "renesas,r8a7791"
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 05/18] arm64: dts: h3ulcb: update header
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This updates H3ULCB device tree header with official board name
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index bcb11a868343..f178fe1730de 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -1,5 +1,5 @@
/*
- * Device Tree Source for the H3ULCB board
+ * Device Tree Source for the H3ULCB (R-Car Starter Kit Premier) board
*
* Copyright (C) 2016 Renesas Electronics Corp.
* Copyright (C) 2016 Cogent Embedded, Inc.
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 06/18] arm64: dts: m3ulcb: add M3ULCB board DT bindings
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Add M3ULCB Device tree bindings Documentation, listing it as a supported
board.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
Documentation/devicetree/bindings/arm/shmobile.txt | 2 ++
1 file changed, 2 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/shmobile.txt b/Documentation/devicetree/bindings/arm/shmobile.txt
index 968ae9a05440..9a3c2631d0d4 100644
--- a/Documentation/devicetree/bindings/arm/shmobile.txt
+++ b/Documentation/devicetree/bindings/arm/shmobile.txt
@@ -61,6 +61,8 @@ Boards:
compatible = "renesas,kzm9g", "renesas,sh73a0"
- Lager (RTP0RC7790SEB00010S)
compatible = "renesas,lager", "renesas,r8a7790"
+ - M3ULCB (R-Car Starter Kit Pro, RTP0RC7796SKB00010S)
+ compatible = "renesas,m3ulcb", "renesas,r8a7796";
- Marzen
compatible = "renesas,marzen", "renesas,r8a7779"
- Porter (M2-LCDP)
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 07/18] arm64: dts: m3ulcb: initial device tree
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Add the initial device tree for the R8A7796 SoC based M3ULCB low cost
board (R-Car Starter Kit Pro)
This commit supports the following peripherals:
- SCIF (console)
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/Makefile | 2 +-
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 51 ++++++++++++++++++++++++++
2 files changed, 52 insertions(+), 1 deletion(-)
create mode 100644 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index eb72830ec9eb..1618e0a3c81d 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -1,5 +1,5 @@
dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
-dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb
+dtb-$(CONFIG_ARCH_R8A7796) += r8a7796-salvator-x.dtb r8a7796-m3ulcb.dtb
always := $(dtb-y)
clean-files := *.dtb
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
new file mode 100644
index 000000000000..1ae0708bb495
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -0,0 +1,51 @@
+/*
+ * Device Tree Source for the M3ULCB (R-Car Starter Kit Pro) board
+ *
+ * Copyright (C) 2016 Renesas Electronics Corp.
+ * Copyright (C) 2016 Cogent Embedded, Inc.
+ *
+ * This file is licensed under the terms of the GNU General Public License
+ * version 2. This program is licensed "as is" without any warranty of any
+ * kind, whether express or implied.
+ */
+
+/dts-v1/;
+#include "r8a7796.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Renesas M3ULCB board based on r8a7796";
+ compatible = "renesas,m3ulcb", "renesas,r8a7796";
+
+ aliases {
+ serial0 = &scif2;
+ };
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory at 48000000 {
+ device_type = "memory";
+ /* first 128MB is reserved for secure area. */
+ reg = <0x0 0x48000000 0x0 0x38000000>;
+ };
+};
+
+&extal_clk {
+ clock-frequency = <16666666>;
+};
+
+&pfc {
+ scif2_pins: scif2 {
+ groups = "scif2_data_a";
+ function = "scif2";
+ };
+};
+
+&scif2 {
+ pinctrl-0 = <&scif2_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 08/18] arm64: dts: m3ulcb: enable SCIF clk and pins
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This enables the external crystal for the SCIF_CLK and its pinctrl, to
be used by the Baud Rate Generator for External Clock (BRG) on (H)SCIF.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 1ae0708bb495..96cda59c2698 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -37,10 +37,18 @@
};
&pfc {
+ pinctrl-0 = <&scif_clk_pins>;
+ pinctrl-names = "default";
+
scif2_pins: scif2 {
groups = "scif2_data_a";
function = "scif2";
};
+
+ scif_clk_pins: scif_clk {
+ groups = "scif_clk_a";
+ function = "scif_clk";
+ };
};
&scif2 {
@@ -49,3 +57,8 @@
status = "okay";
};
+
+&scif_clk {
+ clock-frequency = <14745600>;
+ status = "okay";
+};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 09/18] arm64: dts: m3ulcb: enable GPIO leds
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This supports GPIO leds on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 11 +++++++++++
1 file changed, 11 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 96cda59c2698..49162bd488f8 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -30,6 +30,17 @@
/* first 128MB is reserved for secure area. */
reg = <0x0 0x48000000 0x0 0x38000000>;
};
+
+ leds {
+ compatible = "gpio-leds";
+
+ led5 {
+ gpios = <&gpio6 12 GPIO_ACTIVE_HIGH>;
+ };
+ led6 {
+ gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
+ };
+ };
};
&extal_clk {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 10/18] arm64: dts: m3ulcb: enable GPIO keys
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This supports GPIO keys on M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 49162bd488f8..2f8f183ea0cd 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -12,6 +12,7 @@
/dts-v1/;
#include "r8a7796.dtsi"
#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
/ {
model = "Renesas M3ULCB board based on r8a7796";
@@ -41,6 +42,18 @@
gpios = <&gpio6 13 GPIO_ACTIVE_HIGH>;
};
};
+
+ keyboard {
+ compatible = "gpio-keys";
+
+ key-1 {
+ linux,code = <KEY_1>;
+ label = "SW3";
+ wakeup-source;
+ debounce-interval = <20>;
+ gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
+ };
+ };
};
&extal_clk {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 11/18] arm64: dts: m3ulcb: enable EXTALR clk
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This enables EXTALR clock that can be used for the watchdog.
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 2f8f183ea0cd..5567c46f3753 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -60,6 +60,10 @@
clock-frequency = <16666666>;
};
+&extalr_clk {
+ clock-frequency = <32768>;
+};
+
&pfc {
pinctrl-0 = <&scif_clk_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 12/18] arm64: dts: m3ulcb: enable WDT
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This supports watchdog timer for M3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 5567c46f3753..593d0b4ab31a 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -90,3 +90,8 @@
clock-frequency = <14745600>;
status = "okay";
};
+
+&wdt0 {
+ timeout-sec = <60>;
+ status = "okay";
+};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 13/18] arm64: dts: m3ulcb: enable SDHI0
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This supports SDHI0 on M3ULCB board SD card slot
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 49 ++++++++++++++++++++++++++
1 file changed, 49 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index 593d0b4ab31a..d209e5480ff6 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -54,6 +54,30 @@
gpios = <&gpio6 11 GPIO_ACTIVE_LOW>;
};
};
+
+ vcc_sdhi0: regulator-vcc-sdhi0 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "SDHI0 Vcc";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&gpio5 2 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ };
+
+ vccq_sdhi0: regulator-vccq-sdhi0 {
+ compatible = "regulator-gpio";
+
+ regulator-name = "SDHI0 VccQ";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+ gpios-states = <1>;
+ states = <3300000 1
+ 1800000 0>;
+ };
};
&extal_clk {
@@ -77,6 +101,31 @@
groups = "scif_clk_a";
function = "scif_clk";
};
+
+ sdhi0_pins: sd0 {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <3300>;
+ };
+
+ sdhi0_pins_uhs: sd0_uhs {
+ groups = "sdhi0_data4", "sdhi0_ctrl";
+ function = "sdhi0";
+ power-source = <1800>;
+ };
+};
+
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-1 = <&sdhi0_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <&vcc_sdhi0>;
+ vqmmc-supply = <&vccq_sdhi0>;
+ cd-gpios = <&gpio3 12 GPIO_ACTIVE_LOW>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ status = "okay";
};
&scif2 {
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 14/18] arm64: dts: m3ulcb: enable SDHI2
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This supports SDHI2 for M3ULCB onboard eMMC
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 43 ++++++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
index d209e5480ff6..c3f064ac2cb4 100644
--- a/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
@@ -55,6 +55,24 @@
};
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -113,6 +131,18 @@
function = "sdhi0";
power-source = <1800>;
};
+
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
};
&sdhi0 {
@@ -128,6 +158,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&scif2 {
pinctrl-0 = <&scif2_pins>;
pinctrl-names = "default";
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [PATCH 15/18] arm64: dts: h3ulcb: enable SDHI2
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This supports SDHI2 for H3ULCB onboard eMMC
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 43 ++++++++++++++++++++++++++
1 file changed, 43 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index f178fe1730de..8d0ac076d8e2 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -62,6 +62,24 @@
clock-frequency = <24576000>;
};
+ reg_1p8v: regulator0 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
+ reg_3p3v: regulator1 {
+ compatible = "regulator-fixed";
+ regulator-name = "fixed-3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ regulator-always-on;
+ };
+
vcc_sdhi0: regulator-vcc-sdhi0 {
compatible = "regulator-fixed";
@@ -157,6 +175,18 @@
power-source = <1800>;
};
+ sdhi2_pins: sd2 {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <3300>;
+ };
+
+ sdhi2_pins_uhs: sd2_uhs {
+ groups = "sdhi2_data8", "sdhi2_ctrl";
+ function = "sdhi2";
+ power-source = <1800>;
+ };
+
sound_pins: sound {
groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
function = "ssi";
@@ -273,6 +303,19 @@
status = "okay";
};
+&sdhi2 {
+ /* used for on-board 8bit eMMC */
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ non-removable;
+ status = "okay";
+};
+
&ssi1 {
shared-pin;
};
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
* [GIT PULL] Second Round of Renesas ARM64 Based SoC DT Updates for v4.10
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
Hi Olof, Hi Kevin, Hi Arnd,
Please consider these second round of Renesas ARM64 based SoC DT updates
for v4.10.
This pull request is based on a merge of:
* The previous round of such requests, tagged as renesas-arm64-dt-for-v4.10,
which I have already sent a pull-request for.
* The "Second Round of Renesas ARM Based SoC Drivers Updates for v4.10",
tagged as renesas-drivers2-for-v4.10, which I have also sent a pull
request for. This is included to provide dependencies for adding device
nodes for PRR.
The following changes since commit a59f630b3386cc30c28154f3d5707ee74d4bfe63:
Merge branch 'heads/drivers-for-v4.10' into HEAD (2016-11-15 14:13:37 +0100)
are available in the git repository at:
git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas.git tags/renesas-arm64-dt2-for-v4.10
for you to fetch changes up to 1e7b5e4ee3f1b2c9cb607801a3f0adfa05a0818a:
arm64: dts: r8a7796: Add device node for PRR (2016-11-15 14:15:58 +0100)
----------------------------------------------------------------
Second Round of Renesas ARM64 Based SoC DT Updates for v4.10
Enhancements:
* Add device nodes for PRR
* Add m3ulcb board
* Enable I2C on r8a7796/salvator-x board
* Enable SDHI0 on h3ulcb board
Clean-up:
* Rename SDHI0 pins of h3ulcb board
----------------------------------------------------------------
Geert Uytterhoeven (2):
arm64: dts: r8a7795: Add device node for PRR
arm64: dts: r8a7796: Add device node for PRR
Ulrich Hecht (3):
arm64: dts: r8a7796: add I2C support
arm64: dts: r8a7796: Enable I2C DMA
arm64: dts: r8a7796: salvator-x: enable I2C
Vladimir Barinov (13):
arm64: dts: h3ulcb: update documentation with official board name
arm64: dts: h3ulcb: update header
arm64: dts: m3ulcb: add M3ULCB board DT bindings
arm64: dts: m3ulcb: initial device tree
arm64: dts: m3ulcb: enable SCIF clk and pins
arm64: dts: m3ulcb: enable GPIO leds
arm64: dts: m3ulcb: enable GPIO keys
arm64: dts: m3ulcb: enable EXTALR clk
arm64: dts: m3ulcb: enable WDT
arm64: dts: m3ulcb: enable SDHI0
arm64: dts: m3ulcb: enable SDHI2
arm64: dts: h3ulcb: enable SDHI2
arm64: dts: h3ulcb: rename SDHI0 pins
Documentation/devicetree/bindings/arm/shmobile.txt | 4 +-
arch/arm64/boot/dts/renesas/Makefile | 2 +-
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 53 +++++-
arch/arm64/boot/dts/renesas/r8a7795.dtsi | 5 +
arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts | 189 +++++++++++++++++++++
arch/arm64/boot/dts/renesas/r8a7796-salvator-x.dts | 12 ++
arch/arm64/boot/dts/renesas/r8a7796.dtsi | 116 +++++++++++++
7 files changed, 374 insertions(+), 7 deletions(-)
create mode 100644 arch/arm64/boot/dts/renesas/r8a7796-m3ulcb.dts
^ permalink raw reply
* [PATCH 16/18] arm64: dts: h3ulcb: rename SDHI0 pins
From: Simon Horman @ 2016-11-17 14:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.1479388193.git.horms+renesas@verge.net.au>
From: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
This changes SDHI0 pin names for H3ULCB board
Signed-off-by: Vladimir Barinov <vladimir.barinov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
---
arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
index 8d0ac076d8e2..6ffb0517421a 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-h3ulcb.dts
@@ -163,13 +163,13 @@
function = "avb";
};
- sdhi0_pins_3v3: sd0_3v3 {
+ sdhi0_pins: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <3300>;
};
- sdhi0_pins_1v8: sd0_1v8 {
+ sdhi0_pins_uhs: sd0 {
groups = "sdhi0_data4", "sdhi0_ctrl";
function = "sdhi0";
power-source = <1800>;
@@ -291,8 +291,8 @@
};
&sdhi0 {
- pinctrl-0 = <&sdhi0_pins_3v3>;
- pinctrl-1 = <&sdhi0_pins_1v8>;
+ pinctrl-0 = <&sdhi0_pins>;
+ pinctrl-1 = <&sdhi0_pins_uhs>;
pinctrl-names = "default", "state_uhs";
vmmc-supply = <&vcc_sdhi0>;
--
2.7.0.rc3.207.g0ac5344
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox