* [PATCH 2/2] dt-bindings: Add DT bindings info for FlexRM mailbox driver
From: Rob Herring @ 2016-11-30 21:38 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1480048551-3285-3-git-send-email-anup.patel@broadcom.com>
On Fri, Nov 25, 2016 at 10:05:51AM +0530, Anup Patel wrote:
> This patch adds device tree bindings document for the FlexRM
> mailbox driver.
Bindings document h/w, not drivers.
>
> Reviewed-by: Ray Jui <ray.jui@broadcom.com>
> Reviewed-by: Scott Branden <scott.branden@broadcom.com>
> Signed-off-by: Anup Patel <anup.patel@broadcom.com>
> ---
> .../bindings/mailbox/brcm,flexrm-mbox.txt | 60 ++++++++++++++++++++++
> 1 file changed, 60 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/mailbox/brcm,flexrm-mbox.txt
>
> diff --git a/Documentation/devicetree/bindings/mailbox/brcm,flexrm-mbox.txt b/Documentation/devicetree/bindings/mailbox/brcm,flexrm-mbox.txt
> new file mode 100644
> index 0000000..7969b1c
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mailbox/brcm,flexrm-mbox.txt
> @@ -0,0 +1,60 @@
> +Broadcom FlexRM Mailbox Driver
h/w
> +===============================
> +The Broadcom FlexRM ring manager provides a set of rings which can be
> +used to submit work to offload engines. An SoC may have multiple FlexRM
> +hardware blocks. There is one device tree entry per block. The FlexRM
> +mailbox drivers creates a mailbox instance using FlexRM rings where
> +each mailbox channel is a separate FlexRM ring.
> +
> +Required properties:
> +--------------------
> +- compatible: Should be "brcm,flexrm-mbox"
Sounds generic. Add SoC specific compatible strings please.
> +- reg: Specifies base physical address and size of the FlexRM
> + ring registers
> +- msi-parent: Phandles (and potential Device IDs) to MSI controllers
> + The FlexRM engine will send MSIs (instead of wired
> + interrupts) to CPU. There is one MSI for each FlexRM ring.
One ring is one h/w block, right? How many instances is not really
relevant.
> + Refer devicetree/bindings/interrupt-controller/msi.txt
> +- #mbox-cells: Specifies the number of cells needed to encode a mailbox
> + channel. This should be 3.
> +
> + The 1st cell is the mailbox channel number.
> +
> + The 2nd cell contains MSI completion threshold. This is the
> + number of completion messages for which FlexRM will inject
> + one MSI interrupt to CPU.
> +
> + The 3nd cell contains MSI timer value representing time for
> + which FlexRM will wait to accumulate N completion messages
> + where N is the value specified by 2nd cell above. If FlexRM
> + does not get required number of completion messages in time
> + specified by this cell then it will inject one MSI interrupt
> + to CPU provided atleast one completion message is available.
> +
> +Optional properties:
> +--------------------
> +- dma-coherent: Present if DMA operations made by the FlexRM engine (such
> + as DMA descriptor access, access to buffers pointed by DMA
> + descriptors and read/write pointer updates to DDR) are
> + cache coherent with the CPU.
> +
> +Example:
> +--------
> +crypto_mbox: mbox at 67000000 {
> + compatible = "brcm,flexrm-mbox";
> + reg = <0x67000000 0x200000>;
> + msi-parent = <&gic_its 0x7f00>;
> + #mbox-cells = <3>;
> +};
> +
> +crypto_client {
Is this a h/w block or purely a driver on top of the mailbox? The latter
doesn't belong in DT.
> + ...
> + mboxes = <&crypto_mbox 0 0x1 0xffff>,
> + <&crypto_mbox 1 0x1 0xffff>,
> + <&crypto_mbox 16 0x1 0xffff>,
> + <&crypto_mbox 17 0x1 0xffff>,
> + <&crypto_mbox 30 0x1 0xffff>,
> + <&crypto_mbox 31 0x1 0xffff>;
> + };
> + ...
> +};
> --
> 2.7.4
>
^ permalink raw reply
* [GIT PULL 2/3] ARM: dts: exynos: DT for v4.10, second round
From: Arnd Bergmann @ 2016-11-30 21:39 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479967709-6619-3-git-send-email-krzk@kernel.org>
On Thursday, November 24, 2016 8:08:28 AM CET Krzysztof Kozlowski wrote:
> ----------------------------------------------------------------
> Samsung DeviceTree second update for v4.10:
> 1. Cleanups in MSHC nodes.
> 2. Enable ADC on Odroid boards.
> 3. Fix interrupt flags on recently added DMA sound nodes in Exynos5410.
Pulled into next/dt, thanks!
Arnd
^ permalink raw reply
* [PATCH] dt-bindings: document how to setup rockchip timers as clocksource
From: Alexander Kochetkov @ 2016-11-30 21:40 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161130213006.p6totahjga7546s6@rob-hp-laptop>
> 1 ???. 2016 ?., ? 0:30, Rob Herring <robh@kernel.org> ???????(?):
>
> 1st and 2nd are ambiguous. Plus this is an OS implementation detail that
> doesn't belong in the binding.
>
>> +If you want to bind specific timer as clockevent (i.e. one from alive subsystem)
>> +and specific timer as clocksource, you can number the timers in "aliases" node.
>
> No.
>
> Use and/or describe what are the features of a timer to make the
> decision. There has to be some reason you care which one. One has an
> interrupt and the other doesn't. One is always on. Etc.
Thank you, Rob.
Eventually I abandoned this decision.
I left only one patch, which you confirmed recently.
And sorry for making noise with duplicate patches.
Alexander.
^ permalink raw reply
* [PATCH v5 net-next 0/7] Support Armada 37xx SoC (ARMv8 64-bits) in mvneta driver
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
The Armada 37xx is a new ARMv8 SoC from Marvell using same network
controller as the older Armada 370/38x/XP SoCs. This series adapts the
driver in order to be able to use it on this new SoC. The main changes
are:
- 64-bits support: the first patches allow using the driver on a 64-bit
architecture.
- MBUS support: the mbus configuration is different on Armada 37xx
from the older SoCs.
- per cpu interrupt: Armada 37xx do not support per cpu interrupt for
the NETA IP, the non-per-CPU behavior was added back.
The first patch is an optimization in the rx path in swbm mode.
The second patch remove unnecessary allocation for HWBM.
The first item is solved by patches 4 and 5.
The 2 last items are solved by patch 6.
In patch 7 the dt support is added.
Beside Armada 37xx, this series have been again tested on Armada XP
and Armada 38x (with Hardware Buffer Management and with Software
Buffer Management).
This is the 5th version of the series:
- 1st version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/469588.html
- 2nd version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/470476.html
- 3rd version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/470901.html
- 4th version:
http://lists.infradead.org/pipermail/linux-arm-kernel/2016-November/471039.html
Changelog:
v4 -> v5:
- remove unnecessary cast in patch 3
v3 -> v4:
- Adding new patch: "net: mvneta: do not allocate buffer in rxq init
with HWBM"
- Simplify the HWBM case in patch 3 as suggested by Marcin
v2 -> v3:
- Adding patch 1 "Optimize rx path for small frame"
- Fix the kbuild error by moving the "phys_addr += pp->rx_offset_correction;"
line from patch 2 to patch 3 where rx_offset_correction is introduced.
- Move the memory allocation of the buf_virt_addr of the rxq to be
called by the probe function in order to avoid a memory leak.
Thanks,
Gregory
Gregory CLEMENT (5):
net: mvneta: Optimize rx path for small frame
net: mvneta: Do not allocate buffer in rxq init with HWBM
net: mvneta: Use cacheable memory to store the rx buffer virtual address
net: mvneta: Only disable mvneta_bm for 64-bits
ARM64: dts: marvell: Add network support for Armada 3700
Marcin Wojtas (2):
net: mvneta: Convert to be 64 bits compatible
net: mvneta: Add network support for Armada 3700 SoC
Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt | 7 +-
arch/arm64/boot/dts/marvell/armada-3720-db.dts | 23 +++++-
arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 23 +++++-
drivers/net/ethernet/marvell/Kconfig | 10 +-
drivers/net/ethernet/marvell/mvneta.c | 344 +++++++++++++++++++++++++++++++++++++++++++++++++++---------------------
5 files changed, 305 insertions(+), 102 deletions(-)
base-commit: 436accebb53021ef7c63535f60bda410aa87c136
--
git-series 0.8.10
^ permalink raw reply
* [PATCH v5 net-next 1/7] net: mvneta: Optimize rx path for small frame
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
For small frame reuse the phys_addr variable instead of accessing the
uncacheable value in the rx descriptor.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
drivers/net/ethernet/marvell/mvneta.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 87274d4ab102..1b84f746d748 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -1918,7 +1918,7 @@ static int mvneta_rx_swbm(struct mvneta_port *pp, int rx_todo,
goto err_drop_frame;
dma_sync_single_range_for_cpu(dev->dev.parent,
- rx_desc->buf_phys_addr,
+ phys_addr,
MVNETA_MH_SIZE + NET_SKB_PAD,
rx_bytes,
DMA_FROM_DEVICE);
--
git-series 0.8.10
^ permalink raw reply related
* [PATCH] USB: OHCI: ohci-s3c2410: remove useless functions
From: csmanjuvijay at gmail.com @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
From: Manjunath Goudar <csmanjuvijay@gmail.com>
The ohci_hcd_s3c2410_drv_probe and ohci_hcd_s3c2410_drv_remove
functions are removed as these are useless functions except calling
usb_hcd_s3c2410_probe and usb_hcd_s3c2410_remove functions.
The usb_hcd_s3c2410_probe function renamed to ohci_hcd_s3c2410_drv_probe
and usb_hcd_s3c2410_remove function renamed to ohci_hcd_s3c2410_drv_remove
for proper naming.
This also removes warnings and errors of checkpatch.pl script.
Signed-off-by: Manjunath Goudar <csmanjuvijay@gmail.com>
Cc: Kukjin Kim <kgene@kernel.org>
Cc: Krzysztof Kozlowski <krzk@kernel.org>
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-arm-kernel at lists.infradead.org
Cc: linux-samsung-soc at vger.kernel.org
Cc: linux-usb at vger.kernel.org
Cc: linux-kernel at vger.kernel.org
---
drivers/usb/host/ohci-s3c2410.c | 57 +++++++++++++++++------------------------
1 file changed, 24 insertions(+), 33 deletions(-)
diff --git a/drivers/usb/host/ohci-s3c2410.c b/drivers/usb/host/ohci-s3c2410.c
index d8e03a8..27b75b3 100644
--- a/drivers/usb/host/ohci-s3c2410.c
+++ b/drivers/usb/host/ohci-s3c2410.c
@@ -17,7 +17,7 @@
* Thanks to basprog at mail.ru for updates to newer kernels
*
* This file is licenced under the GPL.
-*/
+ */
#include <linux/clk.h>
#include <linux/io.h>
@@ -43,6 +43,8 @@ static const char hcd_name[] = "ohci-s3c2410";
static struct clk *clk;
static struct clk *usb_clk;
+static struct hc_driver __read_mostly ohci_s3c2410_hc_driver;
+
/* forward definitions */
static void s3c2410_hcd_oc(struct s3c2410_hcd_info *info, int port_oc);
@@ -96,7 +98,7 @@ static void s3c2410_stop_hc(struct platform_device *dev)
*
* update the status data from the hub with anything that
* has been detected by our system
-*/
+ */
static int
ohci_s3c2410_hub_status_data(struct usb_hcd *hcd, char *buf)
@@ -135,7 +137,7 @@ ohci_s3c2410_hub_status_data(struct usb_hcd *hcd, char *buf)
*
* configure the power on a port, by calling the platform device
* routine registered with the platform device
-*/
+ */
static void s3c2410_usb_set_power(struct s3c2410_hcd_info *info,
int port, int to)
@@ -154,7 +156,7 @@ static void s3c2410_usb_set_power(struct s3c2410_hcd_info *info,
* look at control requests to the hub, and see if we need
* to take any action or over-ride the results from the
* request.
-*/
+ */
static int ohci_s3c2410_hub_control(
struct usb_hcd *hcd,
@@ -174,7 +176,8 @@ static int ohci_s3c2410_hub_control(
hcd, typeReq, wValue, wIndex, buf, wLength);
/* if we are only an humble host without any special capabilities
- * process the request straight away and exit */
+ * process the request straight away and exit
+ */
if (info == NULL) {
ret = ohci_hub_control(hcd, typeReq, wValue,
@@ -285,7 +288,7 @@ static int ohci_s3c2410_hub_control(
/* s3c2410_hcd_oc
*
* handle an over-current report
-*/
+ */
static void s3c2410_hcd_oc(struct s3c2410_hcd_info *info, int port_oc)
{
@@ -309,7 +312,8 @@ static void s3c2410_hcd_oc(struct s3c2410_hcd_info *info, int port_oc)
port->oc_changed = 1;
/* ok, once over-current is detected,
- the port needs to be powered down */
+ * the port needs to be powered down
+ */
s3c2410_usb_set_power(info, portno+1, 0);
}
}
@@ -321,26 +325,29 @@ static void s3c2410_hcd_oc(struct s3c2410_hcd_info *info, int port_oc)
/* may be called with controller, bus, and devices active */
/*
- * usb_hcd_s3c2410_remove - shutdown processing for HCD
+ * ohci_hcd_s3c2410_remove - shutdown processing for HCD
* @dev: USB Host Controller being removed
* Context: !in_interrupt()
*
- * Reverses the effect of usb_hcd_3c2410_probe(), first invoking
+ * Reverses the effect of ohci_hcd_3c2410_probe(), first invoking
* the HCD's stop() method. It is always called from a thread
* context, normally "rmmod", "apmd", or something similar.
*
-*/
+ */
-static void
-usb_hcd_s3c2410_remove(struct usb_hcd *hcd, struct platform_device *dev)
+static int
+ohci_hcd_s3c2410_remove(struct platform_device *dev)
{
+ struct usb_hcd *hcd = platform_get_drvdata(dev);
+
usb_remove_hcd(hcd);
s3c2410_stop_hc(dev);
usb_put_hcd(hcd);
+ return 0;
}
/**
- * usb_hcd_s3c2410_probe - initialize S3C2410-based HCDs
+ * ohci_hcd_s3c2410_probe - initialize S3C2410-based HCDs
* Context: !in_interrupt()
*
* Allocates basic resources for this USB host controller, and
@@ -348,8 +355,7 @@ usb_hcd_s3c2410_remove(struct usb_hcd *hcd, struct platform_device *dev)
* through the hotplug entry's driver_data.
*
*/
-static int usb_hcd_s3c2410_probe(const struct hc_driver *driver,
- struct platform_device *dev)
+static int ohci_hcd_s3c2410_probe(struct platform_device *dev)
{
struct usb_hcd *hcd = NULL;
struct s3c2410_hcd_info *info = dev_get_platdata(&dev->dev);
@@ -358,7 +364,7 @@ static int usb_hcd_s3c2410_probe(const struct hc_driver *driver,
s3c2410_usb_set_power(info, 1, 1);
s3c2410_usb_set_power(info, 2, 1);
- hcd = usb_create_hcd(driver, &dev->dev, "s3c24xx");
+ hcd = usb_create_hcd(&ohci_s3c2410_hc_driver, &dev->dev, "s3c24xx");
if (hcd == NULL)
return -ENOMEM;
@@ -404,21 +410,6 @@ static int usb_hcd_s3c2410_probe(const struct hc_driver *driver,
/*-------------------------------------------------------------------------*/
-static struct hc_driver __read_mostly ohci_s3c2410_hc_driver;
-
-static int ohci_hcd_s3c2410_drv_probe(struct platform_device *pdev)
-{
- return usb_hcd_s3c2410_probe(&ohci_s3c2410_hc_driver, pdev);
-}
-
-static int ohci_hcd_s3c2410_drv_remove(struct platform_device *pdev)
-{
- struct usb_hcd *hcd = platform_get_drvdata(pdev);
-
- usb_hcd_s3c2410_remove(hcd, pdev);
- return 0;
-}
-
#ifdef CONFIG_PM
static int ohci_hcd_s3c2410_drv_suspend(struct device *dev)
{
@@ -465,8 +456,8 @@ static const struct of_device_id ohci_hcd_s3c2410_dt_ids[] = {
MODULE_DEVICE_TABLE(of, ohci_hcd_s3c2410_dt_ids);
static struct platform_driver ohci_hcd_s3c2410_driver = {
- .probe = ohci_hcd_s3c2410_drv_probe,
- .remove = ohci_hcd_s3c2410_drv_remove,
+ .probe = ohci_hcd_s3c2410_probe,
+ .remove = ohci_hcd_s3c2410_remove,
.shutdown = usb_hcd_platform_shutdown,
.driver = {
.name = "s3c2410-ohci",
--
2.7.4
^ permalink raw reply related
* [PATCH v5 net-next 2/7] net: mvneta: Do not allocate buffer in rxq init with HWBM
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
For HWBM all buffers are allocated in mvneta_bm_construct() and in runtime
they are put into descriptors by hardware. There is no need to fill them
at this point.
Suggested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
drivers/net/ethernet/marvell/mvneta.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 1b84f746d748..f5319c50f8d9 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -2784,14 +2784,14 @@ static int mvneta_rxq_init(struct mvneta_port *pp,
mvneta_rxq_buf_size_set(pp, rxq,
MVNETA_RX_BUF_SIZE(pp->pkt_size));
mvneta_rxq_bm_disable(pp, rxq);
+ mvneta_rxq_fill(pp, rxq, rxq->size);
} else {
mvneta_rxq_bm_enable(pp, rxq);
mvneta_rxq_long_pool_set(pp, rxq);
mvneta_rxq_short_pool_set(pp, rxq);
+ mvneta_rxq_non_occup_desc_add(pp, rxq, rxq->size);
}
- mvneta_rxq_fill(pp, rxq, rxq->size);
-
return 0;
}
--
git-series 0.8.10
^ permalink raw reply related
* [PATCH v5 net-next 3/7] net: mvneta: Use cacheable memory to store the rx buffer virtual address
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
Until now the virtual address of the received buffer were stored in the
cookie field of the rx descriptor. However, this field is 32-bits only
which prevents to use the driver on a 64-bits architecture.
With this patch the virtual address is stored in an array not shared with
the hardware (no more need to use the DMA API). Thanks to this, it is
possible to use cache contrary to the access of the rx descriptor member.
The change is done in the swbm path only because the hwbm uses the cookie
field, this also means that currently the hwbm is not usable in 64-bits.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
drivers/net/ethernet/marvell/mvneta.c | 34 +++++++++++++++++++---------
1 file changed, 24 insertions(+), 10 deletions(-)
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index f5319c50f8d9..92b9af14c352 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -561,6 +561,9 @@ struct mvneta_rx_queue {
u32 pkts_coal;
u32 time_coal;
+ /* Virtual address of the RX buffer */
+ void **buf_virt_addr;
+
/* Virtual address of the RX DMA descriptors array */
struct mvneta_rx_desc *descs;
@@ -1573,10 +1576,14 @@ static void mvneta_tx_done_pkts_coal_set(struct mvneta_port *pp,
/* Handle rx descriptor fill by setting buf_cookie and buf_phys_addr */
static void mvneta_rx_desc_fill(struct mvneta_rx_desc *rx_desc,
- u32 phys_addr, u32 cookie)
+ u32 phys_addr, void *virt_addr,
+ struct mvneta_rx_queue *rxq)
{
- rx_desc->buf_cookie = cookie;
+ int i;
+
rx_desc->buf_phys_addr = phys_addr;
+ i = rx_desc - rxq->descs;
+ rxq->buf_virt_addr[i] = virt_addr;
}
/* Decrement sent descriptors counter */
@@ -1781,7 +1788,8 @@ EXPORT_SYMBOL_GPL(mvneta_frag_free);
/* Refill processing for SW buffer management */
static int mvneta_rx_refill(struct mvneta_port *pp,
- struct mvneta_rx_desc *rx_desc)
+ struct mvneta_rx_desc *rx_desc,
+ struct mvneta_rx_queue *rxq)
{
dma_addr_t phys_addr;
@@ -1799,7 +1807,7 @@ static int mvneta_rx_refill(struct mvneta_port *pp,
return -ENOMEM;
}
- mvneta_rx_desc_fill(rx_desc, phys_addr, (u32)data);
+ mvneta_rx_desc_fill(rx_desc, phys_addr, data, rxq);
return 0;
}
@@ -1861,7 +1869,7 @@ static void mvneta_rxq_drop_pkts(struct mvneta_port *pp,
for (i = 0; i < rxq->size; i++) {
struct mvneta_rx_desc *rx_desc = rxq->descs + i;
- void *data = (void *)rx_desc->buf_cookie;
+ void *data = rxq->buf_virt_addr[i];
dma_unmap_single(pp->dev->dev.parent, rx_desc->buf_phys_addr,
MVNETA_RX_BUF_SIZE(pp->pkt_size), DMA_FROM_DEVICE);
@@ -1894,12 +1902,13 @@ static int mvneta_rx_swbm(struct mvneta_port *pp, int rx_todo,
unsigned char *data;
dma_addr_t phys_addr;
u32 rx_status, frag_size;
- int rx_bytes, err;
+ int rx_bytes, err, index;
rx_done++;
rx_status = rx_desc->status;
rx_bytes = rx_desc->data_size - (ETH_FCS_LEN + MVNETA_MH_SIZE);
- data = (unsigned char *)rx_desc->buf_cookie;
+ index = rx_desc - rxq->descs;
+ data = rxq->buf_virt_addr[index];
phys_addr = rx_desc->buf_phys_addr;
if (!mvneta_rxq_desc_is_first_last(rx_status) ||
@@ -1938,7 +1947,7 @@ static int mvneta_rx_swbm(struct mvneta_port *pp, int rx_todo,
}
/* Refill processing */
- err = mvneta_rx_refill(pp, rx_desc);
+ err = mvneta_rx_refill(pp, rx_desc, rxq);
if (err) {
netdev_err(dev, "Linux processing - Can't refill\n");
rxq->missed++;
@@ -2020,7 +2029,7 @@ static int mvneta_rx_hwbm(struct mvneta_port *pp, int rx_todo,
rx_done++;
rx_status = rx_desc->status;
rx_bytes = rx_desc->data_size - (ETH_FCS_LEN + MVNETA_MH_SIZE);
- data = (unsigned char *)rx_desc->buf_cookie;
+ data = (u8 *)(uintptr_t)rx_desc->buf_cookie;
phys_addr = rx_desc->buf_phys_addr;
pool_id = MVNETA_RX_GET_BM_POOL_ID(rx_desc);
bm_pool = &pp->bm_priv->bm_pools[pool_id];
@@ -2716,7 +2725,7 @@ static int mvneta_rxq_fill(struct mvneta_port *pp, struct mvneta_rx_queue *rxq,
for (i = 0; i < num; i++) {
memset(rxq->descs + i, 0, sizeof(struct mvneta_rx_desc));
- if (mvneta_rx_refill(pp, rxq->descs + i) != 0) {
+ if (mvneta_rx_refill(pp, rxq->descs + i, rxq) != 0) {
netdev_err(pp->dev, "%s:rxq %d, %d of %d buffs filled\n",
__func__, rxq->id, i, num);
break;
@@ -3865,6 +3874,11 @@ static int mvneta_init(struct device *dev, struct mvneta_port *pp)
rxq->size = pp->rx_ring_size;
rxq->pkts_coal = MVNETA_RX_COAL_PKTS;
rxq->time_coal = MVNETA_RX_COAL_USEC;
+ rxq->buf_virt_addr = devm_kmalloc(pp->dev->dev.parent,
+ rxq->size * sizeof(void *),
+ GFP_KERNEL);
+ if (!rxq->buf_virt_addr)
+ return -ENOMEM;
}
return 0;
--
git-series 0.8.10
^ permalink raw reply related
* [PATCH v5 net-next 4/7] net: mvneta: Convert to be 64 bits compatible
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
From: Marcin Wojtas <mw@semihalf.com>
Prepare the mvneta driver in order to be usable on the 64 bits platform
such as the Armada 3700.
[gregory.clement at free-electrons.com]: this patch was extract from a larger
one to ease review and maintenance.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
drivers/net/ethernet/marvell/mvneta.c | 17 ++++++++++++++++-
1 file changed, 16 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 92b9af14c352..8ef03fb69bcd 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -296,6 +296,12 @@
/* descriptor aligned size */
#define MVNETA_DESC_ALIGNED_SIZE 32
+/* Number of bytes to be taken into account by HW when putting incoming data
+ * to the buffers. It is needed in case NET_SKB_PAD exceeds maximum packet
+ * offset supported in MVNETA_RXQ_CONFIG_REG(q) registers.
+ */
+#define MVNETA_RX_PKT_OFFSET_CORRECTION 64
+
#define MVNETA_RX_PKT_SIZE(mtu) \
ALIGN((mtu) + MVNETA_MH_SIZE + MVNETA_VLAN_TAG_LEN + \
ETH_HLEN + ETH_FCS_LEN, \
@@ -416,6 +422,7 @@ struct mvneta_port {
u64 ethtool_stats[ARRAY_SIZE(mvneta_statistics)];
u32 indir[MVNETA_RSS_LU_TABLE_SIZE];
+ u16 rx_offset_correction;
};
/* The mvneta_tx_desc and mvneta_rx_desc structures describe the
@@ -1807,6 +1814,7 @@ static int mvneta_rx_refill(struct mvneta_port *pp,
return -ENOMEM;
}
+ phys_addr += pp->rx_offset_correction;
mvneta_rx_desc_fill(rx_desc, phys_addr, data, rxq);
return 0;
}
@@ -2782,7 +2790,7 @@ static int mvneta_rxq_init(struct mvneta_port *pp,
mvreg_write(pp, MVNETA_RXQ_SIZE_REG(rxq->id), rxq->size);
/* Set Offset */
- mvneta_rxq_offset_set(pp, rxq, NET_SKB_PAD);
+ mvneta_rxq_offset_set(pp, rxq, NET_SKB_PAD - pp->rx_offset_correction);
/* Set coalescing pkts and time */
mvneta_rx_pkts_coal_set(pp, rxq, rxq->pkts_coal);
@@ -4033,6 +4041,13 @@ static int mvneta_probe(struct platform_device *pdev)
pp->rxq_def = rxq_def;
+ /* Set RX packet offset correction for platforms, whose
+ * NET_SKB_PAD, exceeds 64B. It should be 64B for 64-bit
+ * platforms and 0B for 32-bit ones.
+ */
+ pp->rx_offset_correction =
+ max(0, NET_SKB_PAD - MVNETA_RX_PKT_OFFSET_CORRECTION);
+
pp->indir[0] = rxq_def;
pp->clk = devm_clk_get(&pdev->dev, "core");
--
git-series 0.8.10
^ permalink raw reply related
* [PATCH v5 net-next 5/7] net: mvneta: Only disable mvneta_bm for 64-bits
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
Actually only the mvneta_bm support is not 64-bits compatible.
The mvneta code itself can run on 64-bits architecture.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
drivers/net/ethernet/marvell/Kconfig | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/marvell/Kconfig b/drivers/net/ethernet/marvell/Kconfig
index 66fd9dbb2ca7..2ccea9dd9248 100644
--- a/drivers/net/ethernet/marvell/Kconfig
+++ b/drivers/net/ethernet/marvell/Kconfig
@@ -44,6 +44,7 @@ config MVMDIO
config MVNETA_BM_ENABLE
tristate "Marvell Armada 38x/XP network interface BM support"
depends on MVNETA
+ depends on !64BIT
---help---
This driver supports auxiliary block of the network
interface units in the Marvell ARMADA XP and ARMADA 38x SoC
@@ -58,7 +59,6 @@ config MVNETA
tristate "Marvell Armada 370/38x/XP network interface support"
depends on PLAT_ORION || COMPILE_TEST
depends on HAS_DMA
- depends on !64BIT
select MVMDIO
select FIXED_PHY
---help---
@@ -71,6 +71,7 @@ config MVNETA
config MVNETA_BM
tristate
+ depends on !64BIT
default y if MVNETA=y && MVNETA_BM_ENABLE!=n
default MVNETA_BM_ENABLE
select HWBM
--
git-series 0.8.10
^ permalink raw reply related
* [PATCH v5 net-next 6/7] net: mvneta: Add network support for Armada 3700 SoC
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
From: Marcin Wojtas <mw@semihalf.com>
Armada 3700 is a new ARMv8 SoC from Marvell using same network controller
as older Armada 370/38x/XP. There are however some differences that
needed taking into account when adding support for it:
* open default MBUS window to 4GB of DRAM - Armada 3700 SoC's Mbus
configuration for network controller has to be done on two levels:
global and per-port. The first one is inherited from the
bootloader. The latter can be opened in a default way, leaving
arbitration to the bus controller. Hence filled mbus_dram_target_info
structure is not needed
* make per-CPU operation optional - Recent patches adding RSS and XPS
support for Armada 38x/XP enabled per-CPU operation of the controller
by default. Contrary to older SoC's Armada 3700 SoC's network
controller is not capable of per-CPU processing due to interrupt lines'
connectivity. This patch restores non-per-CPU operation, which is now
optional and depends on neta_armada3700 flag value in mvneta_port
structure. In order not to complicate the code, separate interrupt
subroutine is implemented.
For now, on the Armada 3700, RSS is disabled as the current
implementation depend on the per cpu interrupts.
[gregory.clement at free-electrons.com: extract from a larger patch, replace
some ifdef and port to net-next for v4.10]
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt | 7 +-
drivers/net/ethernet/marvell/Kconfig | 7 +-
drivers/net/ethernet/marvell/mvneta.c | 287 +++++++++++++++++++++++++++++++++++++++++++++++++++---------------------
3 files changed, 214 insertions(+), 87 deletions(-)
diff --git a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
index 73be8970815e..7aa840c8768d 100644
--- a/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
+++ b/Documentation/devicetree/bindings/net/marvell-armada-370-neta.txt
@@ -1,7 +1,10 @@
-* Marvell Armada 370 / Armada XP Ethernet Controller (NETA)
+* Marvell Armada 370 / Armada XP / Armada 3700 Ethernet Controller (NETA)
Required properties:
-- compatible: "marvell,armada-370-neta" or "marvell,armada-xp-neta".
+- compatible: could be one of the followings
+ "marvell,armada-370-neta"
+ "marvell,armada-xp-neta"
+ "marvell,armada-3700-neta"
- reg: address and length of the register set for the device.
- interrupts: interrupt for the device
- phy: See ethernet.txt file in the same directory.
diff --git a/drivers/net/ethernet/marvell/Kconfig b/drivers/net/ethernet/marvell/Kconfig
index 2ccea9dd9248..3b8f11fe5e13 100644
--- a/drivers/net/ethernet/marvell/Kconfig
+++ b/drivers/net/ethernet/marvell/Kconfig
@@ -56,14 +56,15 @@ config MVNETA_BM_ENABLE
buffer management.
config MVNETA
- tristate "Marvell Armada 370/38x/XP network interface support"
- depends on PLAT_ORION || COMPILE_TEST
+ tristate "Marvell Armada 370/38x/XP/37xx network interface support"
+ depends on ARCH_MVEBU || COMPILE_TEST
depends on HAS_DMA
select MVMDIO
select FIXED_PHY
---help---
This driver supports the network interface units in the
- Marvell ARMADA XP, ARMADA 370 and ARMADA 38x SoC family.
+ Marvell ARMADA XP, ARMADA 370, ARMADA 38x and
+ ARMADA 37xx SoC family.
Note that this driver is distinct from the mv643xx_eth
driver, which should be used for the older Marvell SoCs
diff --git a/drivers/net/ethernet/marvell/mvneta.c b/drivers/net/ethernet/marvell/mvneta.c
index 8ef03fb69bcd..ffc0c65068ea 100644
--- a/drivers/net/ethernet/marvell/mvneta.c
+++ b/drivers/net/ethernet/marvell/mvneta.c
@@ -397,6 +397,9 @@ struct mvneta_port {
spinlock_t lock;
bool is_stopped;
+ u32 cause_rx_tx;
+ struct napi_struct napi;
+
/* Core clock */
struct clk *clk;
/* AXI clock */
@@ -422,6 +425,9 @@ struct mvneta_port {
u64 ethtool_stats[ARRAY_SIZE(mvneta_statistics)];
u32 indir[MVNETA_RSS_LU_TABLE_SIZE];
+
+ /* Flags for special SoC configurations */
+ bool neta_armada3700;
u16 rx_offset_correction;
};
@@ -965,14 +971,9 @@ static int mvneta_mbus_io_win_set(struct mvneta_port *pp, u32 base, u32 wsize,
return 0;
}
-/* Assign and initialize pools for port. In case of fail
- * buffer manager will remain disabled for current port.
- */
-static int mvneta_bm_port_init(struct platform_device *pdev,
- struct mvneta_port *pp)
+static int mvneta_bm_port_mbus_init(struct mvneta_port *pp)
{
- struct device_node *dn = pdev->dev.of_node;
- u32 long_pool_id, short_pool_id, wsize;
+ u32 wsize;
u8 target, attr;
int err;
@@ -991,6 +992,25 @@ static int mvneta_bm_port_init(struct platform_device *pdev,
netdev_info(pp->dev, "fail to configure mbus window to BM\n");
return err;
}
+ return 0;
+}
+
+/* Assign and initialize pools for port. In case of fail
+ * buffer manager will remain disabled for current port.
+ */
+static int mvneta_bm_port_init(struct platform_device *pdev,
+ struct mvneta_port *pp)
+{
+ struct device_node *dn = pdev->dev.of_node;
+ u32 long_pool_id, short_pool_id;
+
+ if (!pp->neta_armada3700) {
+ int ret;
+
+ ret = mvneta_bm_port_mbus_init(pp);
+ if (ret)
+ return ret;
+ }
if (of_property_read_u32(dn, "bm,pool-long", &long_pool_id)) {
netdev_info(pp->dev, "missing long pool id\n");
@@ -1359,22 +1379,27 @@ static void mvneta_defaults_set(struct mvneta_port *pp)
for_each_present_cpu(cpu) {
int rxq_map = 0, txq_map = 0;
int rxq, txq;
+ if (!pp->neta_armada3700) {
+ for (rxq = 0; rxq < rxq_number; rxq++)
+ if ((rxq % max_cpu) == cpu)
+ rxq_map |= MVNETA_CPU_RXQ_ACCESS(rxq);
+
+ for (txq = 0; txq < txq_number; txq++)
+ if ((txq % max_cpu) == cpu)
+ txq_map |= MVNETA_CPU_TXQ_ACCESS(txq);
+
+ /* With only one TX queue we configure a special case
+ * which will allow to get all the irq on a single
+ * CPU
+ */
+ if (txq_number == 1)
+ txq_map = (cpu == pp->rxq_def) ?
+ MVNETA_CPU_TXQ_ACCESS(1) : 0;
- for (rxq = 0; rxq < rxq_number; rxq++)
- if ((rxq % max_cpu) == cpu)
- rxq_map |= MVNETA_CPU_RXQ_ACCESS(rxq);
-
- for (txq = 0; txq < txq_number; txq++)
- if ((txq % max_cpu) == cpu)
- txq_map |= MVNETA_CPU_TXQ_ACCESS(txq);
-
- /* With only one TX queue we configure a special case
- * which will allow to get all the irq on a single
- * CPU
- */
- if (txq_number == 1)
- txq_map = (cpu == pp->rxq_def) ?
- MVNETA_CPU_TXQ_ACCESS(1) : 0;
+ } else {
+ txq_map = MVNETA_CPU_TXQ_ACCESS_ALL_MASK;
+ rxq_map = MVNETA_CPU_RXQ_ACCESS_ALL_MASK;
+ }
mvreg_write(pp, MVNETA_CPU_MAP(cpu), rxq_map | txq_map);
}
@@ -2627,6 +2652,17 @@ static void mvneta_set_rx_mode(struct net_device *dev)
/* Interrupt handling - the callback for request_irq() */
static irqreturn_t mvneta_isr(int irq, void *dev_id)
{
+ struct mvneta_port *pp = (struct mvneta_port *)dev_id;
+
+ mvreg_write(pp, MVNETA_INTR_NEW_MASK, 0);
+ napi_schedule(&pp->napi);
+
+ return IRQ_HANDLED;
+}
+
+/* Interrupt handling - the callback for request_percpu_irq() */
+static irqreturn_t mvneta_percpu_isr(int irq, void *dev_id)
+{
struct mvneta_pcpu_port *port = (struct mvneta_pcpu_port *)dev_id;
disable_percpu_irq(port->pp->dev->irq);
@@ -2674,7 +2710,7 @@ static int mvneta_poll(struct napi_struct *napi, int budget)
struct mvneta_pcpu_port *port = this_cpu_ptr(pp->ports);
if (!netif_running(pp->dev)) {
- napi_complete(&port->napi);
+ napi_complete(napi);
return rx_done;
}
@@ -2703,7 +2739,8 @@ static int mvneta_poll(struct napi_struct *napi, int budget)
*/
rx_queue = fls(((cause_rx_tx >> 8) & 0xff));
- cause_rx_tx |= port->cause_rx_tx;
+ cause_rx_tx |= pp->neta_armada3700 ? pp->cause_rx_tx :
+ port->cause_rx_tx;
if (rx_queue) {
rx_queue = rx_queue - 1;
@@ -2717,11 +2754,27 @@ static int mvneta_poll(struct napi_struct *napi, int budget)
if (budget > 0) {
cause_rx_tx = 0;
- napi_complete(&port->napi);
- enable_percpu_irq(pp->dev->irq, 0);
+ napi_complete(napi);
+
+ if (pp->neta_armada3700) {
+ unsigned long flags;
+
+ local_irq_save(flags);
+ mvreg_write(pp, MVNETA_INTR_NEW_MASK,
+ MVNETA_RX_INTR_MASK(rxq_number) |
+ MVNETA_TX_INTR_MASK(txq_number) |
+ MVNETA_MISCINTR_INTR_MASK);
+ local_irq_restore(flags);
+ } else {
+ enable_percpu_irq(pp->dev->irq, 0);
+ }
}
- port->cause_rx_tx = cause_rx_tx;
+ if (pp->neta_armada3700)
+ pp->cause_rx_tx = cause_rx_tx;
+ else
+ port->cause_rx_tx = cause_rx_tx;
+
return rx_done;
}
@@ -2991,11 +3044,16 @@ static void mvneta_start_dev(struct mvneta_port *pp)
/* start the Rx/Tx activity */
mvneta_port_enable(pp);
- /* Enable polling on the port */
- for_each_online_cpu(cpu) {
- struct mvneta_pcpu_port *port = per_cpu_ptr(pp->ports, cpu);
+ if (!pp->neta_armada3700) {
+ /* Enable polling on the port */
+ for_each_online_cpu(cpu) {
+ struct mvneta_pcpu_port *port =
+ per_cpu_ptr(pp->ports, cpu);
- napi_enable(&port->napi);
+ napi_enable(&port->napi);
+ }
+ } else {
+ napi_enable(&pp->napi);
}
/* Unmask interrupts. It has to be done from each CPU */
@@ -3017,10 +3075,15 @@ static void mvneta_stop_dev(struct mvneta_port *pp)
phy_stop(ndev->phydev);
- for_each_online_cpu(cpu) {
- struct mvneta_pcpu_port *port = per_cpu_ptr(pp->ports, cpu);
+ if (!pp->neta_armada3700) {
+ for_each_online_cpu(cpu) {
+ struct mvneta_pcpu_port *port =
+ per_cpu_ptr(pp->ports, cpu);
- napi_disable(&port->napi);
+ napi_disable(&port->napi);
+ }
+ } else {
+ napi_disable(&pp->napi);
}
netif_carrier_off(pp->dev);
@@ -3430,31 +3493,37 @@ static int mvneta_open(struct net_device *dev)
goto err_cleanup_rxqs;
/* Connect to port interrupt line */
- ret = request_percpu_irq(pp->dev->irq, mvneta_isr,
- MVNETA_DRIVER_NAME, pp->ports);
+ if (pp->neta_armada3700)
+ ret = request_irq(pp->dev->irq, mvneta_isr, 0,
+ dev->name, pp);
+ else
+ ret = request_percpu_irq(pp->dev->irq, mvneta_percpu_isr,
+ dev->name, pp->ports);
if (ret) {
netdev_err(pp->dev, "cannot request irq %d\n", pp->dev->irq);
goto err_cleanup_txqs;
}
- /* Enable per-CPU interrupt on all the CPU to handle our RX
- * queue interrupts
- */
- on_each_cpu(mvneta_percpu_enable, pp, true);
+ if (!pp->neta_armada3700) {
+ /* Enable per-CPU interrupt on all the CPU to handle our RX
+ * queue interrupts
+ */
+ on_each_cpu(mvneta_percpu_enable, pp, true);
- pp->is_stopped = false;
- /* Register a CPU notifier to handle the case where our CPU
- * might be taken offline.
- */
- ret = cpuhp_state_add_instance_nocalls(online_hpstate,
- &pp->node_online);
- if (ret)
- goto err_free_irq;
+ pp->is_stopped = false;
+ /* Register a CPU notifier to handle the case where our CPU
+ * might be taken offline.
+ */
+ ret = cpuhp_state_add_instance_nocalls(online_hpstate,
+ &pp->node_online);
+ if (ret)
+ goto err_free_irq;
- ret = cpuhp_state_add_instance_nocalls(CPUHP_NET_MVNETA_DEAD,
- &pp->node_dead);
- if (ret)
- goto err_free_online_hp;
+ ret = cpuhp_state_add_instance_nocalls(CPUHP_NET_MVNETA_DEAD,
+ &pp->node_dead);
+ if (ret)
+ goto err_free_online_hp;
+ }
/* In default link is down */
netif_carrier_off(pp->dev);
@@ -3470,13 +3539,20 @@ static int mvneta_open(struct net_device *dev)
return 0;
err_free_dead_hp:
- cpuhp_state_remove_instance_nocalls(CPUHP_NET_MVNETA_DEAD,
- &pp->node_dead);
+ if (!pp->neta_armada3700)
+ cpuhp_state_remove_instance_nocalls(CPUHP_NET_MVNETA_DEAD,
+ &pp->node_dead);
err_free_online_hp:
- cpuhp_state_remove_instance_nocalls(online_hpstate, &pp->node_online);
+ if (!pp->neta_armada3700)
+ cpuhp_state_remove_instance_nocalls(online_hpstate,
+ &pp->node_online);
err_free_irq:
- on_each_cpu(mvneta_percpu_disable, pp, true);
- free_percpu_irq(pp->dev->irq, pp->ports);
+ if (pp->neta_armada3700) {
+ free_irq(pp->dev->irq, pp);
+ } else {
+ on_each_cpu(mvneta_percpu_disable, pp, true);
+ free_percpu_irq(pp->dev->irq, pp->ports);
+ }
err_cleanup_txqs:
mvneta_cleanup_txqs(pp);
err_cleanup_rxqs:
@@ -3489,23 +3565,30 @@ static int mvneta_stop(struct net_device *dev)
{
struct mvneta_port *pp = netdev_priv(dev);
- /* Inform that we are stopping so we don't want to setup the
- * driver for new CPUs in the notifiers. The code of the
- * notifier for CPU online is protected by the same spinlock,
- * so when we get the lock, the notifer work is done.
- */
- spin_lock(&pp->lock);
- pp->is_stopped = true;
- spin_unlock(&pp->lock);
+ if (!pp->neta_armada3700) {
+ /* Inform that we are stopping so we don't want to setup the
+ * driver for new CPUs in the notifiers. The code of the
+ * notifier for CPU online is protected by the same spinlock,
+ * so when we get the lock, the notifer work is done.
+ */
+ spin_lock(&pp->lock);
+ pp->is_stopped = true;
+ spin_unlock(&pp->lock);
- mvneta_stop_dev(pp);
- mvneta_mdio_remove(pp);
+ mvneta_stop_dev(pp);
+ mvneta_mdio_remove(pp);
cpuhp_state_remove_instance_nocalls(online_hpstate, &pp->node_online);
cpuhp_state_remove_instance_nocalls(CPUHP_NET_MVNETA_DEAD,
&pp->node_dead);
- on_each_cpu(mvneta_percpu_disable, pp, true);
- free_percpu_irq(dev->irq, pp->ports);
+ on_each_cpu(mvneta_percpu_disable, pp, true);
+ free_percpu_irq(dev->irq, pp->ports);
+ } else {
+ mvneta_stop_dev(pp);
+ mvneta_mdio_remove(pp);
+ free_irq(dev->irq, pp);
+ }
+
mvneta_cleanup_rxqs(pp);
mvneta_cleanup_txqs(pp);
@@ -3784,6 +3867,11 @@ static int mvneta_ethtool_set_rxfh(struct net_device *dev, const u32 *indir,
const u8 *key, const u8 hfunc)
{
struct mvneta_port *pp = netdev_priv(dev);
+
+ /* Current code for Armada 3700 doesn't support RSS features yet */
+ if (pp->neta_armada3700)
+ return -EOPNOTSUPP;
+
/* We require at least one supported parameter to be changed
* and no change in any of the unsupported parameters
*/
@@ -3804,6 +3892,10 @@ static int mvneta_ethtool_get_rxfh(struct net_device *dev, u32 *indir, u8 *key,
{
struct mvneta_port *pp = netdev_priv(dev);
+ /* Current code for Armada 3700 doesn't support RSS features yet */
+ if (pp->neta_armada3700)
+ return -EOPNOTSUPP;
+
if (hfunc)
*hfunc = ETH_RSS_HASH_TOP;
@@ -3911,16 +4003,29 @@ static void mvneta_conf_mbus_windows(struct mvneta_port *pp,
win_enable = 0x3f;
win_protect = 0;
- for (i = 0; i < dram->num_cs; i++) {
- const struct mbus_dram_window *cs = dram->cs + i;
- mvreg_write(pp, MVNETA_WIN_BASE(i), (cs->base & 0xffff0000) |
- (cs->mbus_attr << 8) | dram->mbus_dram_target_id);
+ if (dram) {
+ for (i = 0; i < dram->num_cs; i++) {
+ const struct mbus_dram_window *cs = dram->cs + i;
+
+ mvreg_write(pp, MVNETA_WIN_BASE(i),
+ (cs->base & 0xffff0000) |
+ (cs->mbus_attr << 8) |
+ dram->mbus_dram_target_id);
- mvreg_write(pp, MVNETA_WIN_SIZE(i),
- (cs->size - 1) & 0xffff0000);
+ mvreg_write(pp, MVNETA_WIN_SIZE(i),
+ (cs->size - 1) & 0xffff0000);
- win_enable &= ~(1 << i);
- win_protect |= 3 << (2 * i);
+ win_enable &= ~(1 << i);
+ win_protect |= 3 << (2 * i);
+ }
+ } else {
+ /* For Armada3700 open default 4GB Mbus window, leaving
+ * arbitration of target/attribute to a different layer
+ * of configuration.
+ */
+ mvreg_write(pp, MVNETA_WIN_SIZE(0), 0xffff0000);
+ win_enable &= ~BIT(0);
+ win_protect = 3;
}
mvreg_write(pp, MVNETA_BASE_ADDR_ENABLE, win_enable);
@@ -4050,6 +4155,10 @@ static int mvneta_probe(struct platform_device *pdev)
pp->indir[0] = rxq_def;
+ /* Get special SoC configurations */
+ if (of_device_is_compatible(dn, "marvell,armada-3700-neta"))
+ pp->neta_armada3700 = true;
+
pp->clk = devm_clk_get(&pdev->dev, "core");
if (IS_ERR(pp->clk))
pp->clk = devm_clk_get(&pdev->dev, NULL);
@@ -4117,7 +4226,11 @@ static int mvneta_probe(struct platform_device *pdev)
pp->tx_csum_limit = tx_csum_limit;
dram_target_info = mv_mbus_dram_info();
- if (dram_target_info)
+ /* Armada3700 requires setting default configuration of Mbus
+ * windows, however without using filled mbus_dram_target_info
+ * structure.
+ */
+ if (dram_target_info || pp->neta_armada3700)
mvneta_conf_mbus_windows(pp, dram_target_info);
pp->tx_ring_size = MVNETA_MAX_TXD;
@@ -4150,11 +4263,20 @@ static int mvneta_probe(struct platform_device *pdev)
goto err_netdev;
}
- for_each_present_cpu(cpu) {
- struct mvneta_pcpu_port *port = per_cpu_ptr(pp->ports, cpu);
+ /* Armada3700 network controller does not support per-cpu
+ * operation, so only single NAPI should be initialized.
+ */
+ if (pp->neta_armada3700) {
+ netif_napi_add(dev, &pp->napi, mvneta_poll, NAPI_POLL_WEIGHT);
+ } else {
+ for_each_present_cpu(cpu) {
+ struct mvneta_pcpu_port *port =
+ per_cpu_ptr(pp->ports, cpu);
- netif_napi_add(dev, &port->napi, mvneta_poll, NAPI_POLL_WEIGHT);
- port->pp = pp;
+ netif_napi_add(dev, &port->napi, mvneta_poll,
+ NAPI_POLL_WEIGHT);
+ port->pp = pp;
+ }
}
dev->features = NETIF_F_SG | NETIF_F_IP_CSUM | NETIF_F_TSO;
@@ -4239,6 +4361,7 @@ static int mvneta_remove(struct platform_device *pdev)
static const struct of_device_id mvneta_match[] = {
{ .compatible = "marvell,armada-370-neta" },
{ .compatible = "marvell,armada-xp-neta" },
+ { .compatible = "marvell,armada-3700-neta" },
{ }
};
MODULE_DEVICE_TABLE(of, mvneta_match);
--
git-series 0.8.10
^ permalink raw reply related
* [PATCH v5 net-next 7/7] ARM64: dts: marvell: Add network support for Armada 3700
From: Gregory CLEMENT @ 2016-11-30 21:42 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.0270f6d2413a709521fe2c8c17fbebea6f2e78d1.1480542157.git-series.gregory.clement@free-electrons.com>
Add neta nodes for network support both in device tree for the SoC and
the board.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
---
arch/arm64/boot/dts/marvell/armada-3720-db.dts | 23 +++++++++++++++++++-
arch/arm64/boot/dts/marvell/armada-37xx.dtsi | 23 +++++++++++++++++++-
2 files changed, 46 insertions(+), 0 deletions(-)
diff --git a/arch/arm64/boot/dts/marvell/armada-3720-db.dts b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
index 1372e9a6aaa4..c8b82e4145de 100644
--- a/arch/arm64/boot/dts/marvell/armada-3720-db.dts
+++ b/arch/arm64/boot/dts/marvell/armada-3720-db.dts
@@ -81,3 +81,26 @@
&pcie0 {
status = "okay";
};
+
+&mdio {
+ status = "okay";
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
+
+ phy1: ethernet-phy at 1 {
+ reg = <1>;
+ };
+};
+
+ð0 {
+ phy-mode = "rgmii-id";
+ phy = <&phy0>;
+ status = "okay";
+};
+
+ð1 {
+ phy-mode = "rgmii-id";
+ phy = <&phy1>;
+ status = "okay";
+};
diff --git a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
index e9bd58793464..3b8eb45bdc76 100644
--- a/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
+++ b/arch/arm64/boot/dts/marvell/armada-37xx.dtsi
@@ -140,6 +140,29 @@
};
};
+ eth0: ethernet at 30000 {
+ compatible = "marvell,armada-3700-neta";
+ reg = <0x30000 0x4000>;
+ interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sb_periph_clk 8>;
+ status = "disabled";
+ };
+
+ mdio: mdio at 32004 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "marvell,orion-mdio";
+ reg = <0x32004 0x4>;
+ };
+
+ eth1: ethernet at 40000 {
+ compatible = "marvell,armada-3700-neta";
+ reg = <0x40000 0x4000>;
+ interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&sb_periph_clk 7>;
+ status = "disabled";
+ };
+
usb3: usb at 58000 {
compatible = "marvell,armada3700-xhci",
"generic-xhci";
--
git-series 0.8.10
^ permalink raw reply related
* [GIT PULL 2/6] Broadcom devicetree changes for 4.10
From: Florian Fainelli @ 2016-11-30 21:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <5860941.fbiBeiJIy7@wuerfel>
On 11/30/2016 01:27 PM, Arnd Bergmann wrote:
> On Monday, November 21, 2016 9:48:20 PM CET Florian Fainelli wrote:
>> 34 files changed, 1440 insertions(+), 29 deletions(-)
>
> One follow-up: as this was a relatively big branch, it would have
> been nice to get parts of it a little earlier. I see that the
> raspberry-pi changes make up about half of it and came fairly
> late, but the rest apparently was ready much earlier.
>
> If you have the choice between waiting a little longer to
> send all the changes at once, and sending off a good chunk
> a little earlier, better send multiple sets of pull requests.
I was trying to minimize the number of pull requests for you to pull,
but what you are saying makes perfect sense and helps on many aspects.
Thanks a lot for your feedback!
--
Florian
^ permalink raw reply
* [PATCH v2 1/7] net: dt-bindings: add RGMII TX delay configuration to meson8b-dwmac
From: Rob Herring @ 2016-11-30 21:44 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161125130156.17879-2-martin.blumenstingl@googlemail.com>
On Fri, Nov 25, 2016 at 02:01:50PM +0100, Martin Blumenstingl wrote:
> This allows configuring the RGMII TX clock delay. The RGMII clock is
> generated by underlying hardware of the the Meson 8b / GXBB DWMAC glue.
> The configuration depends on the actual hardware (no delay may be
> needed due to the design of the actual circuit, the PHY might add this
> delay, etc.).
>
> Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
> ---
> Documentation/devicetree/bindings/net/meson-dwmac.txt | 14 ++++++++++++++
> 1 file changed, 14 insertions(+)
>
> diff --git a/Documentation/devicetree/bindings/net/meson-dwmac.txt b/Documentation/devicetree/bindings/net/meson-dwmac.txt
> index 89e62dd..f8bc540 100644
> --- a/Documentation/devicetree/bindings/net/meson-dwmac.txt
> +++ b/Documentation/devicetree/bindings/net/meson-dwmac.txt
> @@ -25,6 +25,20 @@ Required properties on Meson8b and newer:
> - "clkin0" - first parent clock of the internal mux
> - "clkin1" - second parent clock of the internal mux
>
> +Optional properties on Meson8b and newer:
> +- amlogic,tx-delay-ns: The internal RGMII TX clock delay (provided
> + by this driver) in nanoseconds. Allowed values
> + are: 0ns, 2ns, 4ns, 6ns.
> + This must be configured when the phy-mode is
> + "rgmii" (typically a value of 2ns is used in
> + this case).
> + When phy-mode is set to "rgmii-id" or
> + "rgmii-txid" the TX clock delay is already
> + provided by the PHY. In that case this
> + property should be set to 0ns (which disables
> + the TX clock delay in the MAC to prevent the
> + clock from going off because both PHY and MAC
> + are adding a delay).
What's the default? Why can't no property mean 0ns delay?
>
> Example for Meson6:
>
> --
> 2.10.2
>
^ permalink raw reply
* [GIT PULL 3/3] arm64: dts: exynos: DT for v4.10, second round
From: Arnd Bergmann @ 2016-11-30 21:47 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479967709-6619-4-git-send-email-krzk@kernel.org>
On Thursday, November 24, 2016 8:08:29 AM CET Krzysztof Kozlowski wrote:
> Samsung DeviceTree arm64 second update for v4.10:
> 1. Add Performance Monitor Unit to Exynos7.
> 2. Add MFC, JPEG and Gscaler to Exynos5433 based TM2 board.
> 3. Cleanups and fixes for recently added TM2 and TM2E boards.
>
>
Pulled into next/dt64, thanks!
Arnd
^ permalink raw reply
* [PATCH 1/2] dt-bindings: usb: add DT binding for s3c2410 USB OHCI controller
From: Rob Herring @ 2016-11-30 21:53 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1480085249-25014-2-git-send-email-sergio.prado@e-labworks.com>
On Fri, Nov 25, 2016 at 12:47:28PM -0200, Sergio Prado wrote:
> Adds the device tree bindings description for Samsung S3C2410 and
> compatible USB OHCI controller.
>
> Signed-off-by: Sergio Prado <sergio.prado@e-labworks.com>
> ---
> .../devicetree/bindings/usb/s3c2410-usb.txt | 22 ++++++++++++++++++++++
> 1 file changed, 22 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/s3c2410-usb.txt
Acked-by: Rob Herring <robh@kernel.org>
^ permalink raw reply
* [GIT PULL] Qualcomm Driver Updates for v4.10 - Part 2
From: Arnd Bergmann @ 2016-11-30 21:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479971131-15142-1-git-send-email-andy.gross@linaro.org>
On Thursday, November 24, 2016 1:05:31 AM CET Andy Gross wrote:
> Qualcomm ARM Based Driver Updates for v4.10 - Part 2
>
> * Fixup QCOM SCM to support MSM8996
>
>
Pulled into next/drivers, thanks!
Arnd
^ permalink raw reply
* [GIT PULL] Qualcomm ARM64 DT Updates for v4.10 - Part 2
From: Arnd Bergmann @ 2016-11-30 21:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479971141-15185-1-git-send-email-andy.gross@linaro.org>
On Thursday, November 24, 2016 1:05:41 AM CET Andy Gross wrote:
> Qualcomm ARM64 Updates for v4.10 - Part 2
>
> * Add SDHC xo clk and 1.8V DDR support
>
Pulled into next/dt64, thanks!
Arnd
^ permalink raw reply
* [GIT PULL] Qualcomm Device Tree Changes for v4.10 - Part 2
From: Arnd Bergmann @ 2016-11-30 22:00 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479971147-15222-1-git-send-email-andy.gross@linaro.org>
On Thursday, November 24, 2016 1:05:47 AM CET Andy Gross wrote:
> Qualcomm Device Tree Changes for v4.10 - Part 2
>
> * Add SDHC xo clk
>
>
Pulled into next/dt, thanks!
ARnd
^ permalink raw reply
* [PATCH] ARM/ARM64: defconfig: drop GPIO_SYSFS on multiplatforms
From: Arnd Bergmann @ 2016-11-30 22:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1479999472-2664-1-git-send-email-linus.walleij@linaro.org>
On Thursday, November 24, 2016 3:57:52 PM CET Linus Walleij wrote:
> The sysfs ABI to GPIO is marked obsolete and should not be
> encouraged. Users should be encouraged to switch to using the
> character device.
>
> Let's begin by removing it from the multi defconfigs. Then
> as time goes by I can aggressively remove it from other
> defconfigs.
>
> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
> ---
> ARM SoC folks: please apply this for whatever branch holds
> defconfig changes.
> ---
> arch/arm/configs/multi_v5_defconfig | 1 -
> arch/arm/configs/multi_v7_defconfig | 1 -
> arch/arm64/configs/defconfig | 1 -
> 3 files changed, 3 deletions(-)
>
Hmm, while this is a trivial change, we normally put the defconfig
changes for arm and arm64 into two separate next/* branches.
I've split the patch up accordingly and slightly modified the
changelog text to match.
Arnd
^ permalink raw reply
* [GIT PULL 1/3] Rockchip defconfig64 changes for 4.10
From: Arnd Bergmann @ 2016-11-30 22:06 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1594090.z775ZFR2cz@phil>
On Thursday, November 24, 2016 4:41:48 PM CET Heiko Stuebner wrote:
> 64bit defconfig changes to allow arm64 Rockchip socs
> to basically boot.
>
Pulled into next/arm64, thanks!
Arnd
^ permalink raw reply
* [GIT PULL 2/3] Rockchip dts64 changes for 4.10
From: Arnd Bergmann @ 2016-11-30 22:09 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1856918.gK9kzau163@phil>
On Thursday, November 24, 2016 4:42:35 PM CET Heiko Stuebner wrote:
> Some more powerdomains and usb2-otg support for the rk3399 as well
> as the binding doc for the 32bit rk1108 eval board to prevent it
> from conflicting with the recently added 64bit px5 board.
>
>
Pulled into next/dt64, thanks!
Arnd
^ permalink raw reply
* [GIT PULL] ARM64: berlin: DT changes for v4.10
From: Arnd Bergmann @ 2016-11-30 22:18 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161125175339.40748efa@xhacker>
On Friday, November 25, 2016 5:53:39 PM CET Jisheng Zhang wrote:
> Berlin64 DT changes for v4.10
>
> - fix some dtc compiler warnings
>
Pulled into next/dt64, thanks!
Arnd
^ permalink raw reply
* [GIT PULL] ZTE arm64 device tree updates for 4.10
From: Arnd Bergmann @ 2016-11-30 22:21 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20161128141934.GA20556@dragon>
On Monday, November 28, 2016 10:19:35 PM CET Shawn Guo wrote:
> ZTE arm64 device tree update for 4.10:
>
> Add clock controller device nodes, including one top clock controller,
> two low speed clock controllers and one audio clock controller.
>
> ----------------------------------------------------------------
>
Pulled into next/dt64, thanks!
Arnd
^ permalink raw reply
* [PATCH 0/5] Meson GXL and GXM USB support
From: Rob Herring @ 2016-11-30 22:22 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAFBinCAA_JEtr_0Ze0thoRaEKMnWQMKcPxJ8y88zkWAAhuxsMw@mail.gmail.com>
On Sun, Nov 27, 2016 at 11:42:02PM +0100, Martin Blumenstingl wrote:
> Hello Kishon,
>
> On Sat, Nov 26, 2016 at 3:56 PM, Martin Blumenstingl
> <martin.blumenstingl@googlemail.com> wrote:
> > USB support on GXL and GXM differs a lot from Meson8b and GXBB:
> > The most obvious change is that GXL and GXM now have one dwc3
> > controller and one dwc2 controller (instead of two dwc2 controllers).
> > With that there are also new USB PHYs.
> >
> > Due to lack of hardware I was only able to test this on a board with
> > GXM, but as far as I understand the hardware my preparations should be
> > correct (so it should also work on GXL).
> >
> > dwc2 will probably stay unused on most GXM devices since it's limited
> > to device mode via some dwc2 hardware configuration register.
> >
> > dwc3 is probably used on all devices, even if there is more than just
> > one USB port. dwc3 has a built-in USB2 hub - on GXL this hub has two
> > ports enabled, while on GXM there are three ports enabled (see below
This hub is an actual USB hub? If so, then you should probably model the
USB bus topology (which we have a binding definition for).
> > for lsusb output). There are no USB3 ports enabled in the dwc3 hardware
> > configuration, meaning that the SoC is limited to high-speed mode.
> > On my GXM device the dwc3 hardware configuration forces it into "host
> > only" mode.
> >
> > The SoCs contain two PHY blocks: one USB3 PHY and up to four USB2 PHYs
> > (on GXM there are only three enabled, but the registers should support
> > up to four).
> > The USB3 PHY also handles the OTG interrupts, but since dwc3's hardware
> > configuration enforces "host only" mode I was not able to test this. It
> > simply takes care of an interrupt and then notifies all related PHYs
> > about the new mode.
> > The USB2 PHY block is a bit different: I created one PHY driver which
> > spans all "PHY ports" because the handling is a bit tricky. It turns
> > out that for each available USB port in dwc3's hub the corresponding
> > PHY must be enabled (even if there is no physical port - in my case
> > port 3 is not connected to anything, but disabling the PHY breaks
> > ports 1 and 2 as well).
> > I decided not not pass the USB2 PHYs directly to dwc3 due to three
> > reasons: 1. the USB3 PHY (which holds a reference to all relevant
> > USB2 PHY ports) controls the mode of the USB2 PHY ports (since both
> > are used with the same controller and thus it makes sense to keep the
> > mode consistent across all ports) 2. the dwc3 driver does not support
> > passing multiple USB2 PHYs (only one USB2 and one USB3 PHY can be
> > passed to it) 3. it is similar to how the vendor reference driver
> > manages the PHYs. Please note that this coupling is not a fixed, this
> > is all configurable via devicetree (so if the third USB2 PHY has to
> > be passed two the dwc2 controller then this is still possible by
> > just moving on PHY reference in the .dts).
> after not staring at my own code for 24 hours I realized this:
> (I went through quite a few iterations before getting these drivers to work)
> I'm basically re-modelling an "USB PHY hub" with my USB3 PHY driver
> (there's one "upstream" PHY interface which is passed to dwc3 and
> multiple downstream PHYs, each for one port on dwc3's internal hub).
> With this approach I could split each of the the USB2s into separate
> nodes again (instead of one devicetree node with #phy-cells = <1>) as
> the USB3 PHY is taking care of that special "we have to enable all
> ports or no port will be usable".
>
> We could go even one step further: why implement this in the Meson GXL
> specific PHY driver - why not implement a generic "phy-hub" driver
> (which would be valid whenever the PHY controller has to manage
> multiple PHYs at once, but wants to keep them all in a consistent
> state).
> The devicetree could look like this:
> usb2_phy_hub: phy at 0 {
> compatible = "phy-hub";
> phys = <&other_phy1>, <&other_phy 2>;
> };
>
> &dwc3 {
> phys = <&usb2_phy_hub>, <&usb3_phy0>;
> phy-names = "usb2-phy", "usb3-phy";
> };
I'm okay with a hub if it is modeled as a USB hub. Here though, it
looks like you are just trying to group things which doesn't need to be
in DT.
>
> The generic phy-hub driver would then implement all phy_ops callbacks
> and pass then to each of it's downstream PHYs.
You can have generic drivers without a generic binding.
> That's just what came into my head - please let me know what you think
> of this or share your ideas on how to approach this!
>
> > The coupling of the USB2 and USB3 PHYs is the reason why I sent the
> > two drivers in one patch, even though they are handling different IP
> > blocks (different registers, etc.).
> >
> > Unfortunately there are no datasheets available for any of these PHYs.
> > Both drivers were written by reading the reference drivers provided by
> > Amlogic and analyzing the registers on the kernel that was shipped with
> > my board.
> >
> > As a last note: the dwc3 driver currently only explicitly enables the
> > first USB port "DWC3_GUSB2PHYCFG(0)" in the internal hub. The hardware
> > seems to enable the other two (DWC3_GUSB2PHYCFG(1) and
> > DWC3_GUSB2PHYCFG(2)) automatically. I will ask the dwc3 maintainers if
> > changes to dwc3 are desired any how these should look like, but for now
> > it's working fine even without changes there.
> >
> > lsusb output on GXM for the dwc3 hub:
> > Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
> > ...
> > Hub Port Status:
> > Port 1: 0000.0100 power
> > Port 2: 0000.0100 power
> > Port 3: 0000.0100 power
> >
> > NOTE: The devicetree changes depend on my previous series:
> > "[PATCH 0/2] minor GXL and GXM improvements" - see [0]
> >
> > NOTE2: This series depends on an upstream dwc3/xhci-plat DMA fix
> > (special thanks to Arnd Bergmann and Sriram Dash for fixing that):
> > "[PATCH v5 0/6] inherit dma configuration from parent dev" - see [1]
> >
> > I have a tree with all dependencies applied available at [2] if
> > someone wants a quick way to test this (I don't take any responsibility
> > if anything explodes though).
> >
> > [0] http://lists.infradead.org/pipermail/linux-amlogic/2016-November/001665.html
> > [1] http://marc.info/?l=linux-usb&m=147938307209685&w=2
> > [2] https://github.com/xdarklight/linux/commits/meson-gx-integration-4.10-20161126
> >
> > Martin Blumenstingl (5):
> > Documentation: dt-bindings: Add documentation for Meson GXL USB2/3
> > PHYs
> > phy: meson: add USB2 and USB3 PHY support for Meson GXL
> > arm64: dts: meson-gxl: add USB support
> > ARM64: dts: meson-gxm: add GXM specific USB configuration
> > ARM64: dts: meson-gx-p23x-q20x: enable USB on P23x and Q20x boards
> >
> > .../devicetree/bindings/phy/meson-gxl-usb2-phy.txt | 25 ++
> > .../devicetree/bindings/phy/meson-gxl-usb3-phy.txt | 27 ++
> > .../arm64/boot/dts/amlogic/meson-gx-p23x-q20x.dtsi | 12 +
> > arch/arm64/boot/dts/amlogic/meson-gxl.dtsi | 49 +++
> > .../arm64/boot/dts/amlogic/meson-gxm-s912-q200.dts | 17 +
> > arch/arm64/boot/dts/amlogic/meson-gxm.dtsi | 10 +
> > drivers/phy/Kconfig | 13 +
> > drivers/phy/Makefile | 2 +
> > drivers/phy/phy-meson-gxl-usb2.c | 374 ++++++++++++++++++++
> > drivers/phy/phy-meson-gxl-usb3.c | 377 +++++++++++++++++++++
> > 10 files changed, 906 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/phy/meson-gxl-usb2-phy.txt
> > create mode 100644 Documentation/devicetree/bindings/phy/meson-gxl-usb3-phy.txt
> > create mode 100644 drivers/phy/phy-meson-gxl-usb2.c
> > create mode 100644 drivers/phy/phy-meson-gxl-usb3.c
> >
> > --
> > 2.10.2
> >
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox