* [PATCH v2 2/7] clk: sunxi-ng: Implement factors offsets
From: Maxime Ripard @ 2017-01-10 7:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.8762813dc78858261716126c700983d4aee00458.1484035021.git-series.maxime.ripard@free-electrons.com>
The factors we've seen so far all had an offset of one. However, on the
earlier Allwinner SoCs, some factors could have no offset at all, meaning
that the value computed to reach the rate we want to use was the one we had
to program in the registers.
Implement an additional field for the factors that can have such an offset
(linears, not based on a power of two) to specify that offset.
This offset is not linked to the extremums that can be specified in those
structures too. The minimum and maximum are representing the range of
values we can use to try to compute the best rate. The offset comes later
on when we want to set the best value in the registers.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/ccu_div.h | 10 +++++++++-
drivers/clk/sunxi-ng/ccu_mp.c | 10 +++++++---
drivers/clk/sunxi-ng/ccu_mult.c | 4 ++--
drivers/clk/sunxi-ng/ccu_mult.h | 20 ++++++++++++++------
drivers/clk/sunxi-ng/ccu_nk.c | 14 ++++++++++----
drivers/clk/sunxi-ng/ccu_nkm.c | 18 +++++++++++++-----
drivers/clk/sunxi-ng/ccu_nkmp.c | 17 +++++++++++++----
drivers/clk/sunxi-ng/ccu_nm.c | 13 ++++++++++---
8 files changed, 78 insertions(+), 28 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu_div.h b/drivers/clk/sunxi-ng/ccu_div.h
index 06540f7cf41c..08d074451204 100644
--- a/drivers/clk/sunxi-ng/ccu_div.h
+++ b/drivers/clk/sunxi-ng/ccu_div.h
@@ -41,6 +41,7 @@ struct ccu_div_internal {
u8 width;
u32 max;
+ u32 offset;
u32 flags;
@@ -58,20 +59,27 @@ struct ccu_div_internal {
#define _SUNXI_CCU_DIV_TABLE(_shift, _width, _table) \
_SUNXI_CCU_DIV_TABLE_FLAGS(_shift, _width, _table, 0)
-#define _SUNXI_CCU_DIV_MAX_FLAGS(_shift, _width, _max, _flags) \
+#define _SUNXI_CCU_DIV_OFFSET_MAX_FLAGS(_shift, _width, _off, _max, _flags) \
{ \
.shift = _shift, \
.width = _width, \
.flags = _flags, \
.max = _max, \
+ .offset = _off, \
}
+#define _SUNXI_CCU_DIV_MAX_FLAGS(_shift, _width, _max, _flags) \
+ _SUNXI_CCU_DIV_OFFSET_MAX_FLAGS(_shift, _width, 1, _max, _flags)
+
#define _SUNXI_CCU_DIV_FLAGS(_shift, _width, _flags) \
_SUNXI_CCU_DIV_MAX_FLAGS(_shift, _width, 0, _flags)
#define _SUNXI_CCU_DIV_MAX(_shift, _width, _max) \
_SUNXI_CCU_DIV_MAX_FLAGS(_shift, _width, _max, 0)
+#define _SUNXI_CCU_DIV_OFFSET(_shift, _width, _offset) \
+ _SUNXI_CCU_DIV_OFFSET_MAX_FLAGS(_shift, _width, _offset, 0, 0)
+
#define _SUNXI_CCU_DIV(_shift, _width) \
_SUNXI_CCU_DIV_FLAGS(_shift, _width, 0)
diff --git a/drivers/clk/sunxi-ng/ccu_mp.c b/drivers/clk/sunxi-ng/ccu_mp.c
index ebb1b31568a5..22c2ca7a2a22 100644
--- a/drivers/clk/sunxi-ng/ccu_mp.c
+++ b/drivers/clk/sunxi-ng/ccu_mp.c
@@ -89,11 +89,14 @@ static unsigned long ccu_mp_recalc_rate(struct clk_hw *hw,
m = reg >> cmp->m.shift;
m &= (1 << cmp->m.width) - 1;
+ m += cmp->m.offset;
+ if (!m)
+ m++;
p = reg >> cmp->p.shift;
p &= (1 << cmp->p.width) - 1;
- return (parent_rate >> p) / (m + 1);
+ return (parent_rate >> p) / m;
}
static int ccu_mp_determine_rate(struct clk_hw *hw,
@@ -124,9 +127,10 @@ static int ccu_mp_set_rate(struct clk_hw *hw, unsigned long rate,
reg = readl(cmp->common.base + cmp->common.reg);
reg &= ~GENMASK(cmp->m.width + cmp->m.shift - 1, cmp->m.shift);
reg &= ~GENMASK(cmp->p.width + cmp->p.shift - 1, cmp->p.shift);
+ reg |= (m - cmp->m.offset) << cmp->m.shift;
+ reg |= ilog2(p) << cmp->p.shift;
- writel(reg | (ilog2(p) << cmp->p.shift) | ((m - 1) << cmp->m.shift),
- cmp->common.base + cmp->common.reg);
+ writel(reg, cmp->common.base + cmp->common.reg);
spin_unlock_irqrestore(cmp->common.lock, flags);
diff --git a/drivers/clk/sunxi-ng/ccu_mult.c b/drivers/clk/sunxi-ng/ccu_mult.c
index 826302464650..bf5e11c803f9 100644
--- a/drivers/clk/sunxi-ng/ccu_mult.c
+++ b/drivers/clk/sunxi-ng/ccu_mult.c
@@ -85,7 +85,7 @@ static unsigned long ccu_mult_recalc_rate(struct clk_hw *hw,
ccu_mux_helper_adjust_parent_for_prediv(&cm->common, &cm->mux, -1,
&parent_rate);
- return parent_rate * (val + 1);
+ return parent_rate * (val + cm->mult.offset);
}
static int ccu_mult_determine_rate(struct clk_hw *hw,
@@ -122,7 +122,7 @@ static int ccu_mult_set_rate(struct clk_hw *hw, unsigned long rate,
reg = readl(cm->common.base + cm->common.reg);
reg &= ~GENMASK(cm->mult.width + cm->mult.shift - 1, cm->mult.shift);
- writel(reg | ((_cm.mult - 1) << cm->mult.shift),
+ writel(reg | ((_cm.mult - cm->mult.offset) << cm->mult.shift),
cm->common.base + cm->common.reg);
spin_unlock_irqrestore(cm->common.lock, flags);
diff --git a/drivers/clk/sunxi-ng/ccu_mult.h b/drivers/clk/sunxi-ng/ccu_mult.h
index bd2e38b5a32a..84839641dfdf 100644
--- a/drivers/clk/sunxi-ng/ccu_mult.h
+++ b/drivers/clk/sunxi-ng/ccu_mult.h
@@ -6,20 +6,28 @@
#include "ccu_mux.h"
struct ccu_mult_internal {
+ u8 offset;
u8 shift;
u8 width;
u8 min;
};
-#define _SUNXI_CCU_MULT_MIN(_shift, _width, _min) \
- { \
- .shift = _shift, \
- .width = _width, \
- .min = _min, \
+#define _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, _offset, _min) \
+ { \
+ .min = _min, \
+ .offset = _offset, \
+ .shift = _shift, \
+ .width = _width, \
}
+#define _SUNXI_CCU_MULT_MIN(_shift, _width, _min) \
+ _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, 1, _min)
+
+#define _SUNXI_CCU_MULT_OFFSET(_shift, _width, _offset) \
+ _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, _offset, 1)
+
#define _SUNXI_CCU_MULT(_shift, _width) \
- _SUNXI_CCU_MULT_MIN(_shift, _width, 1)
+ _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, 1, 1)
struct ccu_mult {
u32 enable;
diff --git a/drivers/clk/sunxi-ng/ccu_nk.c b/drivers/clk/sunxi-ng/ccu_nk.c
index eaf0fdf78d2b..90117d3ead8c 100644
--- a/drivers/clk/sunxi-ng/ccu_nk.c
+++ b/drivers/clk/sunxi-ng/ccu_nk.c
@@ -76,12 +76,17 @@ static unsigned long ccu_nk_recalc_rate(struct clk_hw *hw,
n = reg >> nk->n.shift;
n &= (1 << nk->n.width) - 1;
+ n += nk->n.offset;
+ if (!n)
+ n++;
k = reg >> nk->k.shift;
k &= (1 << nk->k.width) - 1;
+ k += nk->k.offset;
+ if (!k)
+ k++;
- rate = parent_rate * (n + 1) * (k + 1);
-
+ rate = parent_rate * n * k;
if (nk->common.features & CCU_FEATURE_FIXED_POSTDIV)
rate /= nk->fixed_post_div;
@@ -135,8 +140,9 @@ static int ccu_nk_set_rate(struct clk_hw *hw, unsigned long rate,
reg &= ~GENMASK(nk->n.width + nk->n.shift - 1, nk->n.shift);
reg &= ~GENMASK(nk->k.width + nk->k.shift - 1, nk->k.shift);
- writel(reg | ((_nk.k - 1) << nk->k.shift) | ((_nk.n - 1) << nk->n.shift),
- nk->common.base + nk->common.reg);
+ reg |= (_nk.k - nk->k.offset) << nk->k.shift;
+ reg |= (_nk.n - nk->n.offset) << nk->n.shift;
+ writel(reg, nk->common.base + nk->common.reg);
spin_unlock_irqrestore(nk->common.lock, flags);
diff --git a/drivers/clk/sunxi-ng/ccu_nkm.c b/drivers/clk/sunxi-ng/ccu_nkm.c
index 9b840a47a94d..3caaf9d603e2 100644
--- a/drivers/clk/sunxi-ng/ccu_nkm.c
+++ b/drivers/clk/sunxi-ng/ccu_nkm.c
@@ -82,14 +82,23 @@ static unsigned long ccu_nkm_recalc_rate(struct clk_hw *hw,
n = reg >> nkm->n.shift;
n &= (1 << nkm->n.width) - 1;
+ n += nkm->n.offset;
+ if (!n)
+ n++;
k = reg >> nkm->k.shift;
k &= (1 << nkm->k.width) - 1;
+ k += nkm->k.offset;
+ if (!k)
+ k++;
m = reg >> nkm->m.shift;
m &= (1 << nkm->m.width) - 1;
+ m += nkm->m.offset;
+ if (!m)
+ m++;
- return parent_rate * (n + 1) * (k + 1) / (m + 1);
+ return parent_rate * n * k / m;
}
static unsigned long ccu_nkm_round_rate(struct ccu_mux_internal *mux,
@@ -145,10 +154,9 @@ static int ccu_nkm_set_rate(struct clk_hw *hw, unsigned long rate,
reg &= ~GENMASK(nkm->k.width + nkm->k.shift - 1, nkm->k.shift);
reg &= ~GENMASK(nkm->m.width + nkm->m.shift - 1, nkm->m.shift);
- reg |= (_nkm.n - 1) << nkm->n.shift;
- reg |= (_nkm.k - 1) << nkm->k.shift;
- reg |= (_nkm.m - 1) << nkm->m.shift;
-
+ reg |= (_nkm.n - nkm->n.offset) << nkm->n.shift;
+ reg |= (_nkm.k - nkm->k.offset) << nkm->k.shift;
+ reg |= (_nkm.m - nkm->m.offset) << nkm->m.shift;
writel(reg, nkm->common.base + nkm->common.reg);
spin_unlock_irqrestore(nkm->common.lock, flags);
diff --git a/drivers/clk/sunxi-ng/ccu_nkmp.c b/drivers/clk/sunxi-ng/ccu_nkmp.c
index 684c42da3ebb..da2bba02b845 100644
--- a/drivers/clk/sunxi-ng/ccu_nkmp.c
+++ b/drivers/clk/sunxi-ng/ccu_nkmp.c
@@ -88,17 +88,26 @@ static unsigned long ccu_nkmp_recalc_rate(struct clk_hw *hw,
n = reg >> nkmp->n.shift;
n &= (1 << nkmp->n.width) - 1;
+ n += nkmp->n.offset;
+ if (!n)
+ n++;
k = reg >> nkmp->k.shift;
k &= (1 << nkmp->k.width) - 1;
+ k += nkmp->k.offset;
+ if (!k)
+ k++;
m = reg >> nkmp->m.shift;
m &= (1 << nkmp->m.width) - 1;
+ m += nkmp->m.offset;
+ if (!m)
+ m++;
p = reg >> nkmp->p.shift;
p &= (1 << nkmp->p.width) - 1;
- return (parent_rate * (n + 1) * (k + 1) >> p) / (m + 1);
+ return parent_rate * n * k >> p / m;
}
static long ccu_nkmp_round_rate(struct clk_hw *hw, unsigned long rate,
@@ -148,9 +157,9 @@ static int ccu_nkmp_set_rate(struct clk_hw *hw, unsigned long rate,
reg &= ~GENMASK(nkmp->m.width + nkmp->m.shift - 1, nkmp->m.shift);
reg &= ~GENMASK(nkmp->p.width + nkmp->p.shift - 1, nkmp->p.shift);
- reg |= (_nkmp.n - 1) << nkmp->n.shift;
- reg |= (_nkmp.k - 1) << nkmp->k.shift;
- reg |= (_nkmp.m - 1) << nkmp->m.shift;
+ reg |= (_nkmp.n - nkmp->n.offset) << nkmp->n.shift;
+ reg |= (_nkmp.k - nkmp->k.offset) << nkmp->k.shift;
+ reg |= (_nkmp.m - nkmp->m.offset) << nkmp->m.shift;
reg |= ilog2(_nkmp.p) << nkmp->p.shift;
writel(reg, nkmp->common.base + nkmp->common.reg);
diff --git a/drivers/clk/sunxi-ng/ccu_nm.c b/drivers/clk/sunxi-ng/ccu_nm.c
index c9f3b6c982f0..158d74e0215f 100644
--- a/drivers/clk/sunxi-ng/ccu_nm.c
+++ b/drivers/clk/sunxi-ng/ccu_nm.c
@@ -80,11 +80,17 @@ static unsigned long ccu_nm_recalc_rate(struct clk_hw *hw,
n = reg >> nm->n.shift;
n &= (1 << nm->n.width) - 1;
+ n += nm->n.offset;
+ if (!n)
+ n++;
m = reg >> nm->m.shift;
m &= (1 << nm->m.width) - 1;
+ m += nm->m.offset;
+ if (!m)
+ m++;
- return parent_rate * (n + 1) / (m + 1);
+ return parent_rate * n / m;
}
static long ccu_nm_round_rate(struct clk_hw *hw, unsigned long rate,
@@ -129,8 +135,9 @@ static int ccu_nm_set_rate(struct clk_hw *hw, unsigned long rate,
reg &= ~GENMASK(nm->n.width + nm->n.shift - 1, nm->n.shift);
reg &= ~GENMASK(nm->m.width + nm->m.shift - 1, nm->m.shift);
- writel(reg | ((_nm.m - 1) << nm->m.shift) | ((_nm.n - 1) << nm->n.shift),
- nm->common.base + nm->common.reg);
+ reg |= (_nm.n - nm->n.offset) << nm->n.shift;
+ reg |= (_nm.m - nm->m.offset) << nm->m.shift;
+ writel(reg, nm->common.base + nm->common.reg);
spin_unlock_irqrestore(nm->common.lock, flags);
--
git-series 0.8.11
^ permalink raw reply related
* [PATCH v2 3/7] clk: sunxi-ng: Implement multiplier maximum
From: Maxime Ripard @ 2017-01-10 7:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.8762813dc78858261716126c700983d4aee00458.1484035021.git-series.maxime.ripard@free-electrons.com>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/ccu_mult.c | 4 ++--
drivers/clk/sunxi-ng/ccu_mult.h | 10 ++++++----
drivers/clk/sunxi-ng/ccu_nk.c | 8 ++++----
drivers/clk/sunxi-ng/ccu_nkm.c | 8 ++++----
drivers/clk/sunxi-ng/ccu_nkmp.c | 8 ++++----
drivers/clk/sunxi-ng/ccu_nm.c | 4 ++--
6 files changed, 22 insertions(+), 20 deletions(-)
diff --git a/drivers/clk/sunxi-ng/ccu_mult.c b/drivers/clk/sunxi-ng/ccu_mult.c
index bf5e11c803f9..fccfe1e1961a 100644
--- a/drivers/clk/sunxi-ng/ccu_mult.c
+++ b/drivers/clk/sunxi-ng/ccu_mult.c
@@ -41,7 +41,7 @@ static unsigned long ccu_mult_round_rate(struct ccu_mux_internal *mux,
struct _ccu_mult _cm;
_cm.min = 1;
- _cm.max = 1 << cm->mult.width;
+ _cm.max = cm->mult.max ?: 1 << cm->mult.width;
ccu_mult_find_best(parent_rate, rate, &_cm);
return parent_rate * _cm.mult;
@@ -114,7 +114,7 @@ static int ccu_mult_set_rate(struct clk_hw *hw, unsigned long rate,
&parent_rate);
_cm.min = cm->mult.min;
- _cm.max = 1 << cm->mult.width;
+ _cm.max = cm->mult.max ?: 1 << cm->mult.width;
ccu_mult_find_best(parent_rate, rate, &_cm);
spin_lock_irqsave(cm->common.lock, flags);
diff --git a/drivers/clk/sunxi-ng/ccu_mult.h b/drivers/clk/sunxi-ng/ccu_mult.h
index 84839641dfdf..524acddfcb2e 100644
--- a/drivers/clk/sunxi-ng/ccu_mult.h
+++ b/drivers/clk/sunxi-ng/ccu_mult.h
@@ -10,24 +10,26 @@ struct ccu_mult_internal {
u8 shift;
u8 width;
u8 min;
+ u8 max;
};
-#define _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, _offset, _min) \
+#define _SUNXI_CCU_MULT_OFFSET_MIN_MAX(_shift, _width, _offset, _min, _max) \
{ \
.min = _min, \
+ .max = _max, \
.offset = _offset, \
.shift = _shift, \
.width = _width, \
}
#define _SUNXI_CCU_MULT_MIN(_shift, _width, _min) \
- _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, 1, _min)
+ _SUNXI_CCU_MULT_OFFSET_MIN_MAX(_shift, _width, 1, _min, 0)
#define _SUNXI_CCU_MULT_OFFSET(_shift, _width, _offset) \
- _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, _offset, 1)
+ _SUNXI_CCU_MULT_OFFSET_MIN_MAX(_shift, _width, _offset, 1, 0)
#define _SUNXI_CCU_MULT(_shift, _width) \
- _SUNXI_CCU_MULT_OFFSET_MIN(_shift, _width, 1, 1)
+ _SUNXI_CCU_MULT_OFFSET_MIN_MAX(_shift, _width, 1, 1, 0)
struct ccu_mult {
u32 enable;
diff --git a/drivers/clk/sunxi-ng/ccu_nk.c b/drivers/clk/sunxi-ng/ccu_nk.c
index 90117d3ead8c..b9e9b8a9d1b4 100644
--- a/drivers/clk/sunxi-ng/ccu_nk.c
+++ b/drivers/clk/sunxi-ng/ccu_nk.c
@@ -103,9 +103,9 @@ static long ccu_nk_round_rate(struct clk_hw *hw, unsigned long rate,
rate *= nk->fixed_post_div;
_nk.min_n = nk->n.min;
- _nk.max_n = 1 << nk->n.width;
+ _nk.max_n = nk->n.max ?: 1 << nk->n.width;
_nk.min_k = nk->k.min;
- _nk.max_k = 1 << nk->k.width;
+ _nk.max_k = nk->k.max ?: 1 << nk->k.width;
ccu_nk_find_best(*parent_rate, rate, &_nk);
rate = *parent_rate * _nk.n * _nk.k;
@@ -128,9 +128,9 @@ static int ccu_nk_set_rate(struct clk_hw *hw, unsigned long rate,
rate = rate * nk->fixed_post_div;
_nk.min_n = nk->n.min;
- _nk.max_n = 1 << nk->n.width;
+ _nk.max_n = nk->n.max ?: 1 << nk->n.width;
_nk.min_k = nk->k.min;
- _nk.max_k = 1 << nk->k.width;
+ _nk.max_k = nk->k.max ?: 1 << nk->k.width;
ccu_nk_find_best(parent_rate, rate, &_nk);
diff --git a/drivers/clk/sunxi-ng/ccu_nkm.c b/drivers/clk/sunxi-ng/ccu_nkm.c
index 3caaf9d603e2..71f81e95a061 100644
--- a/drivers/clk/sunxi-ng/ccu_nkm.c
+++ b/drivers/clk/sunxi-ng/ccu_nkm.c
@@ -110,9 +110,9 @@ static unsigned long ccu_nkm_round_rate(struct ccu_mux_internal *mux,
struct _ccu_nkm _nkm;
_nkm.min_n = nkm->n.min;
- _nkm.max_n = 1 << nkm->n.width;
+ _nkm.max_n = nkm->n.max ?: 1 << nkm->n.width;
_nkm.min_k = nkm->k.min;
- _nkm.max_k = 1 << nkm->k.width;
+ _nkm.max_k = nkm->k.max ?: 1 << nkm->k.width;
_nkm.min_m = 1;
_nkm.max_m = nkm->m.max ?: 1 << nkm->m.width;
@@ -139,9 +139,9 @@ static int ccu_nkm_set_rate(struct clk_hw *hw, unsigned long rate,
u32 reg;
_nkm.min_n = nkm->n.min;
- _nkm.max_n = 1 << nkm->n.width;
+ _nkm.max_n = nkm->n.max ?: 1 << nkm->n.width;
_nkm.min_k = nkm->k.min;
- _nkm.max_k = 1 << nkm->k.width;
+ _nkm.max_k = nkm->k.max ?: 1 << nkm->k.width;
_nkm.min_m = 1;
_nkm.max_m = nkm->m.max ?: 1 << nkm->m.width;
diff --git a/drivers/clk/sunxi-ng/ccu_nkmp.c b/drivers/clk/sunxi-ng/ccu_nkmp.c
index da2bba02b845..a2b40a000157 100644
--- a/drivers/clk/sunxi-ng/ccu_nkmp.c
+++ b/drivers/clk/sunxi-ng/ccu_nkmp.c
@@ -117,9 +117,9 @@ static long ccu_nkmp_round_rate(struct clk_hw *hw, unsigned long rate,
struct _ccu_nkmp _nkmp;
_nkmp.min_n = nkmp->n.min;
- _nkmp.max_n = 1 << nkmp->n.width;
+ _nkmp.max_n = nkmp->n.max ?: 1 << nkmp->n.width;
_nkmp.min_k = nkmp->k.min;
- _nkmp.max_k = 1 << nkmp->k.width;
+ _nkmp.max_k = nkmp->k.max ?: 1 << nkmp->k.width;
_nkmp.min_m = 1;
_nkmp.max_m = nkmp->m.max ?: 1 << nkmp->m.width;
_nkmp.min_p = 1;
@@ -139,9 +139,9 @@ static int ccu_nkmp_set_rate(struct clk_hw *hw, unsigned long rate,
u32 reg;
_nkmp.min_n = 1;
- _nkmp.max_n = 1 << nkmp->n.width;
+ _nkmp.max_n = nkmp->n.max ?: 1 << nkmp->n.width;
_nkmp.min_k = 1;
- _nkmp.max_k = 1 << nkmp->k.width;
+ _nkmp.max_k = nkmp->k.max ?: 1 << nkmp->k.width;
_nkmp.min_m = 1;
_nkmp.max_m = nkmp->m.max ?: 1 << nkmp->m.width;
_nkmp.min_p = 1;
diff --git a/drivers/clk/sunxi-ng/ccu_nm.c b/drivers/clk/sunxi-ng/ccu_nm.c
index 158d74e0215f..af71b1909cd9 100644
--- a/drivers/clk/sunxi-ng/ccu_nm.c
+++ b/drivers/clk/sunxi-ng/ccu_nm.c
@@ -100,7 +100,7 @@ static long ccu_nm_round_rate(struct clk_hw *hw, unsigned long rate,
struct _ccu_nm _nm;
_nm.min_n = nm->n.min;
- _nm.max_n = 1 << nm->n.width;
+ _nm.max_n = nm->n.max ?: 1 << nm->n.width;
_nm.min_m = 1;
_nm.max_m = nm->m.max ?: 1 << nm->m.width;
@@ -123,7 +123,7 @@ static int ccu_nm_set_rate(struct clk_hw *hw, unsigned long rate,
ccu_frac_helper_disable(&nm->common, &nm->frac);
_nm.min_n = 1;
- _nm.max_n = 1 << nm->n.width;
+ _nm.max_n = nm->n.max ?: 1 << nm->n.width;
_nm.min_m = 1;
_nm.max_m = nm->m.max ?: 1 << nm->m.width;
--
git-series 0.8.11
^ permalink raw reply related
* [PATCH v2 4/7] clk: sunxi-ng: Add clocks and resets indices for sun5i
From: Maxime Ripard @ 2017-01-10 7:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.8762813dc78858261716126c700983d4aee00458.1484035021.git-series.maxime.ripard@free-electrons.com>
The SoCs part of the sun5i family share the DTs, so we need consistant
indices in order to still share the DTs.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
include/dt-bindings/clock/sun5i-ccu.h | 103 +++++++++++++++++++++++++++-
include/dt-bindings/reset/sun5i-ccu.h | 32 ++++++++-
2 files changed, 135 insertions(+), 0 deletions(-)
create mode 100644 include/dt-bindings/clock/sun5i-ccu.h
create mode 100644 include/dt-bindings/reset/sun5i-ccu.h
diff --git a/include/dt-bindings/clock/sun5i-ccu.h b/include/dt-bindings/clock/sun5i-ccu.h
new file mode 100644
index 000000000000..792ebd9c30e6
--- /dev/null
+++ b/include/dt-bindings/clock/sun5i-ccu.h
@@ -0,0 +1,103 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _DT_BINDINGS_CLK_SUN5I_H_
+#define _DT_BINDINGS_CLK_SUN5I_H_
+
+#define CLK_HOSC 1
+
+#define CLK_CPU 18
+
+#define CLK_AHB_OTG 24
+#define CLK_AHB_EHCI 25
+#define CLK_AHB_OHCI 26
+#define CLK_AHB_SS 27
+#define CLK_AHB_DMA 28
+#define CLK_AHB_BIST 29
+#define CLK_AHB_MMC0 30
+#define CLK_AHB_MMC1 31
+#define CLK_AHB_MMC2 32
+#define CLK_AHB_NAND 33
+#define CLK_AHB_SDRAM 34
+#define CLK_AHB_EMAC 35
+#define CLK_AHB_TS 36
+#define CLK_AHB_SPI0 37
+#define CLK_AHB_SPI1 38
+#define CLK_AHB_SPI2 39
+#define CLK_AHB_GPS 40
+#define CLK_AHB_HSTIMER 41
+#define CLK_AHB_VE 42
+#define CLK_AHB_TVE 43
+#define CLK_AHB_LCD 44
+#define CLK_AHB_CSI 45
+#define CLK_AHB_HDMI 46
+#define CLK_AHB_DE_BE 47
+#define CLK_AHB_DE_FE 48
+#define CLK_AHB_IEP 49
+#define CLK_AHB_GPU 50
+#define CLK_APB0_CODEC 51
+#define CLK_APB0_SPDIF 52
+#define CLK_APB0_I2S 53
+#define CLK_APB0_PIO 54
+#define CLK_APB0_IR 55
+#define CLK_APB0_KEYPAD 56
+#define CLK_APB1_I2C0 57
+#define CLK_APB1_I2C1 58
+#define CLK_APB1_I2C2 59
+#define CLK_APB1_UART0 60
+#define CLK_APB1_UART1 61
+#define CLK_APB1_UART2 62
+#define CLK_APB1_UART3 63
+#define CLK_NAND 64
+#define CLK_MMC0 65
+#define CLK_MMC1 66
+#define CLK_MMC2 67
+#define CLK_TS 68
+#define CLK_SS 69
+#define CLK_SPI0 70
+#define CLK_SPI1 71
+#define CLK_SPI2 72
+#define CLK_IR 73
+#define CLK_I2S 74
+#define CLK_SPDIF 75
+#define CLK_KEYPAD 76
+#define CLK_USB_OHCI 77
+#define CLK_USB_PHY0 78
+#define CLK_USB_PHY1 79
+#define CLK_GPS 80
+#define CLK_DRAM_VE 81
+#define CLK_DRAM_CSI 82
+#define CLK_DRAM_TS 83
+#define CLK_DRAM_TVE 84
+#define CLK_DRAM_DE_FE 85
+#define CLK_DRAM_DE_BE 86
+#define CLK_DRAM_ACE 87
+#define CLK_DRAM_IEP 88
+#define CLK_DE_BE 89
+#define CLK_DE_FE 90
+#define CLK_TCON_CH0 91
+
+#define CLK_TCON_CH1 93
+#define CLK_CSI 94
+#define CLK_VE 95
+#define CLK_CODEC 96
+#define CLK_AVS 97
+#define CLK_HDMI 98
+#define CLK_GPU 99
+
+#define CLK_IEP 101
+
+#endif /* _DT_BINDINGS_CLK_SUN5I_H_ */
diff --git a/include/dt-bindings/reset/sun5i-ccu.h b/include/dt-bindings/reset/sun5i-ccu.h
new file mode 100644
index 000000000000..c2b9726b5026
--- /dev/null
+++ b/include/dt-bindings/reset/sun5i-ccu.h
@@ -0,0 +1,32 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _RST_SUN5I_H_
+#define _RST_SUN5I_H_
+
+#define RST_USB_PHY0 0
+#define RST_USB_PHY1 1
+#define RST_GPS 2
+#define RST_DE_BE 3
+#define RST_DE_FE 4
+#define RST_TVE 5
+#define RST_LCD 6
+#define RST_CSI 7
+#define RST_VE 8
+#define RST_GPU 9
+#define RST_IEP 10
+
+#endif /* _RST_SUN5I_H_ */
--
git-series 0.8.11
^ permalink raw reply related
* [PATCH v2 5/7] clk: sunxi-ng: Add sun5i CCU driver
From: Maxime Ripard @ 2017-01-10 7:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.8762813dc78858261716126c700983d4aee00458.1484035021.git-series.maxime.ripard@free-electrons.com>
The Allwinner A10s, A13, R8 and NextThing GR8 are all based on the same
silicon, and all share the same clocks.
However, they're not packaged in the same way, and therefore not all the
controllers are actually available on all these SoCs.
Introduce a clock controller driver for all these SoCs with different
compatibles to take that into account.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
drivers/clk/sunxi-ng/Kconfig | 10 +-
drivers/clk/sunxi-ng/Makefile | 1 +-
drivers/clk/sunxi-ng/ccu-sun5i.c | 1008 +++++++++++++++++++++++++++++++-
drivers/clk/sunxi-ng/ccu-sun5i.h | 68 ++-
4 files changed, 1087 insertions(+), 0 deletions(-)
create mode 100644 drivers/clk/sunxi-ng/ccu-sun5i.c
create mode 100644 drivers/clk/sunxi-ng/ccu-sun5i.h
diff --git a/drivers/clk/sunxi-ng/Kconfig b/drivers/clk/sunxi-ng/Kconfig
index 8454c6e3dd65..fc5d85016839 100644
--- a/drivers/clk/sunxi-ng/Kconfig
+++ b/drivers/clk/sunxi-ng/Kconfig
@@ -64,6 +64,16 @@ config SUN50I_A64_CCU
select SUNXI_CCU_PHASE
default ARM64 && ARCH_SUNXI
+config SUN5I_CCU
+ bool "Support for the Allwinner sun5i family CCM"
+ select SUNXI_CCU_DIV
+ select SUNXI_CCU_NK
+ select SUNXI_CCU_NKM
+ select SUNXI_CCU_NM
+ select SUNXI_CCU_MP
+ select SUNXI_CCU_PHASE
+ default MACH_SUN5I
+
config SUN6I_A31_CCU
bool "Support for the Allwinner A31/A31s CCU"
select SUNXI_CCU_DIV
diff --git a/drivers/clk/sunxi-ng/Makefile b/drivers/clk/sunxi-ng/Makefile
index 24fbc6e5deb8..d3fc917314e9 100644
--- a/drivers/clk/sunxi-ng/Makefile
+++ b/drivers/clk/sunxi-ng/Makefile
@@ -19,6 +19,7 @@ obj-$(CONFIG_SUNXI_CCU_MP) += ccu_mp.o
# SoC support
obj-$(CONFIG_SUN50I_A64_CCU) += ccu-sun50i-a64.o
+obj-$(CONFIG_SUN5I_CCU) += ccu-sun5i.o
obj-$(CONFIG_SUN6I_A31_CCU) += ccu-sun6i-a31.o
obj-$(CONFIG_SUN8I_A23_CCU) += ccu-sun8i-a23.o
obj-$(CONFIG_SUN8I_A33_CCU) += ccu-sun8i-a33.o
diff --git a/drivers/clk/sunxi-ng/ccu-sun5i.c b/drivers/clk/sunxi-ng/ccu-sun5i.c
new file mode 100644
index 000000000000..3d44a2bef11f
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun5i.c
@@ -0,0 +1,1008 @@
+/*
+ * Copyright (c) 2016 Maxime Ripard. All rights reserved.
+ *
+ * This software is licensed under the terms of the GNU General Public
+ * License version 2, as published by the Free Software Foundation, and
+ * may be copied, distributed, and modified under those terms.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk-provider.h>
+#include <linux/of_address.h>
+
+#include "ccu_common.h"
+#include "ccu_reset.h"
+
+#include "ccu_div.h"
+#include "ccu_gate.h"
+#include "ccu_mp.h"
+#include "ccu_mult.h"
+#include "ccu_nk.h"
+#include "ccu_nkm.h"
+#include "ccu_nkmp.h"
+#include "ccu_nm.h"
+#include "ccu_phase.h"
+
+#include "ccu-sun5i.h"
+
+static struct ccu_nkmp pll_core_clk = {
+ .enable = BIT(31),
+ .n = _SUNXI_CCU_MULT_OFFSET(8, 5, 0),
+ .k = _SUNXI_CCU_MULT(4, 2),
+ .m = _SUNXI_CCU_DIV(0, 2),
+ .p = _SUNXI_CCU_DIV(16, 2),
+ .common = {
+ .reg = 0x000,
+ .hw.init = CLK_HW_INIT("pll-core",
+ "hosc",
+ &ccu_nkmp_ops,
+ 0),
+ },
+};
+
+/*
+ * The Audio PLL is supposed to have 4 outputs: 3 fixed factors from
+ * the base (2x, 4x and 8x), and one variable divider (the one true
+ * pll audio).
+ *
+ * We don't have any need for the variable divider for now, so we just
+ * hardcode it to match with the clock names
+ */
+#define SUN5I_PLL_AUDIO_REG 0x008
+
+static struct ccu_nm pll_audio_base_clk = {
+ .enable = BIT(31),
+ .n = _SUNXI_CCU_MULT_OFFSET(8, 7, 0),
+
+ /*
+ * The datasheet is wrong here, this doesn't have any
+ * offset
+ */
+ .m = _SUNXI_CCU_DIV_OFFSET(0, 5, 0),
+ .common = {
+ .reg = 0x008,
+ .hw.init = CLK_HW_INIT("pll-audio-base",
+ "hosc",
+ &ccu_nm_ops,
+ 0),
+ },
+};
+
+static struct ccu_mult pll_video0_clk = {
+ .enable = BIT(31),
+ .mult = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(0, 7, 0, 9, 127),
+ .frac = _SUNXI_CCU_FRAC(BIT(15), BIT(14),
+ 270000000, 297000000),
+ .common = {
+ .reg = 0x010,
+ .features = CCU_FEATURE_FRACTIONAL,
+ .hw.init = CLK_HW_INIT("pll-video0",
+ "osc3M",
+ &ccu_mult_ops,
+ 0),
+ },
+};
+
+static struct ccu_nkmp pll_ve_clk = {
+ .enable = BIT(31),
+ .n = _SUNXI_CCU_MULT_OFFSET(8, 5, 0),
+ .k = _SUNXI_CCU_MULT(4, 2),
+ .m = _SUNXI_CCU_DIV(0, 2),
+ .p = _SUNXI_CCU_DIV(16, 2),
+ .common = {
+ .reg = 0x018,
+ .hw.init = CLK_HW_INIT("pll-ve",
+ "hosc",
+ &ccu_nkmp_ops,
+ 0),
+ },
+};
+
+static struct ccu_nk pll_ddr_base_clk = {
+ .enable = BIT(31),
+ .n = _SUNXI_CCU_MULT_OFFSET(8, 5, 0),
+ .k = _SUNXI_CCU_MULT(4, 2),
+ .common = {
+ .reg = 0x020,
+ .hw.init = CLK_HW_INIT("pll-ddr-base",
+ "hosc",
+ &ccu_nk_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_M(pll_ddr_clk, "pll-ddr", "pll-ddr-base", 0x020, 0, 2,
+ CLK_IS_CRITICAL);
+
+static struct ccu_div pll_ddr_other_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(16, 2, CLK_DIVIDER_POWER_OF_TWO),
+
+ .common = {
+ .reg = 0x020,
+ .hw.init = CLK_HW_INIT("pll-ddr-other", "pll-ddr-base",
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct ccu_nk pll_periph_clk = {
+ .enable = BIT(31),
+ .n = _SUNXI_CCU_MULT_OFFSET(8, 5, 0),
+ .k = _SUNXI_CCU_MULT(4, 2),
+ .fixed_post_div = 2,
+ .common = {
+ .reg = 0x028,
+ .features = CCU_FEATURE_FIXED_POSTDIV,
+ .hw.init = CLK_HW_INIT("pll-periph",
+ "hosc",
+ &ccu_nk_ops,
+ 0),
+ },
+};
+
+static struct ccu_mult pll_video1_clk = {
+ .enable = BIT(31),
+ .mult = _SUNXI_CCU_MULT_OFFSET_MIN_MAX(0, 7, 0, 9, 127),
+ .frac = _SUNXI_CCU_FRAC(BIT(15), BIT(14),
+ 270000000, 297000000),
+ .common = {
+ .reg = 0x030,
+ .features = CCU_FEATURE_FRACTIONAL,
+ .hw.init = CLK_HW_INIT("pll-video1",
+ "osc3M",
+ &ccu_mult_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(hosc_clk, "hosc", "osc24M", 0x050, BIT(0), 0);
+
+#define SUN5I_AHB_REG 0x054
+static const char * const cpu_parents[] = { "osc32k", "hosc",
+ "pll-core" , "pll-periph" };
+static const struct ccu_mux_fixed_prediv cpu_predivs[] = {
+ { .index = 3, .div = 3, },
+};
+static struct ccu_mux cpu_clk = {
+ .mux = {
+ .shift = 16,
+ .width = 2,
+ .fixed_predivs = cpu_predivs,
+ .n_predivs = ARRAY_SIZE(cpu_predivs),
+ },
+ .common = {
+ .reg = 0x054,
+ .features = CCU_FEATURE_FIXED_PREDIV,
+ .hw.init = CLK_HW_INIT_PARENTS("cpu",
+ cpu_parents,
+ &ccu_mux_ops,
+ CLK_IS_CRITICAL),
+ }
+};
+
+static SUNXI_CCU_M(axi_clk, "axi", "cpu", 0x054, 0, 2, 0);
+
+static const char * const ahb_parents[] = { "axi" , "cpu", "pll-periph" };
+static const struct ccu_mux_fixed_prediv ahb_predivs[] = {
+ { .index = 2, .div = 2, },
+};
+static struct ccu_div ahb_clk = {
+ .div = _SUNXI_CCU_DIV_FLAGS(4, 2, CLK_DIVIDER_POWER_OF_TWO),
+ .mux = {
+ .shift = 6,
+ .width = 2,
+ .fixed_predivs = ahb_predivs,
+ .n_predivs = ARRAY_SIZE(ahb_predivs),
+ },
+
+ .common = {
+ .reg = 0x054,
+ .hw.init = CLK_HW_INIT_PARENTS("ahb",
+ ahb_parents,
+ &ccu_div_ops,
+ 0),
+ },
+};
+
+static struct clk_div_table apb0_div_table[] = {
+ { .val = 0, .div = 2 },
+ { .val = 1, .div = 2 },
+ { .val = 2, .div = 4 },
+ { .val = 3, .div = 8 },
+ { /* Sentinel */ },
+};
+static SUNXI_CCU_DIV_TABLE(apb0_clk, "apb0", "ahb",
+ 0x054, 8, 2, apb0_div_table, 0);
+
+static const char * const apb1_parents[] = { "hosc", "pll-periph", "osc32k" };
+static SUNXI_CCU_MP_WITH_MUX(apb1_clk, "apb1", apb1_parents, 0x058,
+ 0, 5, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ 0);
+
+static SUNXI_CCU_GATE(axi_dram_clk, "axi-dram", "axi",
+ 0x05c, BIT(0), 0);
+
+static SUNXI_CCU_GATE(ahb_otg_clk, "ahb-otg", "ahb",
+ 0x060, BIT(0), 0);
+static SUNXI_CCU_GATE(ahb_ehci_clk, "ahb-ehci", "ahb",
+ 0x060, BIT(1), 0);
+static SUNXI_CCU_GATE(ahb_ohci_clk, "ahb-ohci", "ahb",
+ 0x060, BIT(2), 0);
+static SUNXI_CCU_GATE(ahb_ss_clk, "ahb-ss", "ahb",
+ 0x060, BIT(5), 0);
+static SUNXI_CCU_GATE(ahb_dma_clk, "ahb-dma", "ahb",
+ 0x060, BIT(6), 0);
+static SUNXI_CCU_GATE(ahb_bist_clk, "ahb-bist", "ahb",
+ 0x060, BIT(6), 0);
+static SUNXI_CCU_GATE(ahb_mmc0_clk, "ahb-mmc0", "ahb",
+ 0x060, BIT(8), 0);
+static SUNXI_CCU_GATE(ahb_mmc1_clk, "ahb-mmc1", "ahb",
+ 0x060, BIT(9), 0);
+static SUNXI_CCU_GATE(ahb_mmc2_clk, "ahb-mmc2", "ahb",
+ 0x060, BIT(10), 0);
+static SUNXI_CCU_GATE(ahb_nand_clk, "ahb-nand", "ahb",
+ 0x060, BIT(13), 0);
+static SUNXI_CCU_GATE(ahb_sdram_clk, "ahb-sdram", "ahb",
+ 0x060, BIT(14), CLK_IS_CRITICAL);
+static SUNXI_CCU_GATE(ahb_emac_clk, "ahb-emac", "ahb",
+ 0x060, BIT(17), 0);
+static SUNXI_CCU_GATE(ahb_ts_clk, "ahb-ts", "ahb",
+ 0x060, BIT(18), 0);
+static SUNXI_CCU_GATE(ahb_spi0_clk, "ahb-spi0", "ahb",
+ 0x060, BIT(20), 0);
+static SUNXI_CCU_GATE(ahb_spi1_clk, "ahb-spi1", "ahb",
+ 0x060, BIT(21), 0);
+static SUNXI_CCU_GATE(ahb_spi2_clk, "ahb-spi2", "ahb",
+ 0x060, BIT(22), 0);
+static SUNXI_CCU_GATE(ahb_gps_clk, "ahb-gps", "ahb",
+ 0x060, BIT(26), 0);
+static SUNXI_CCU_GATE(ahb_hstimer_clk, "ahb-hstimer", "ahb",
+ 0x060, BIT(28), 0);
+
+static SUNXI_CCU_GATE(ahb_ve_clk, "ahb-ve", "ahb",
+ 0x064, BIT(0), 0);
+static SUNXI_CCU_GATE(ahb_tve_clk, "ahb-tve", "ahb",
+ 0x064, BIT(2), 0);
+static SUNXI_CCU_GATE(ahb_lcd_clk, "ahb-lcd", "ahb",
+ 0x064, BIT(4), 0);
+static SUNXI_CCU_GATE(ahb_csi_clk, "ahb-csi", "ahb",
+ 0x064, BIT(8), 0);
+static SUNXI_CCU_GATE(ahb_hdmi_clk, "ahb-hdmi", "ahb",
+ 0x064, BIT(11), 0);
+static SUNXI_CCU_GATE(ahb_de_be_clk, "ahb-de-be", "ahb",
+ 0x064, BIT(12), 0);
+static SUNXI_CCU_GATE(ahb_de_fe_clk, "ahb-de-fe", "ahb",
+ 0x064, BIT(14), 0);
+static SUNXI_CCU_GATE(ahb_iep_clk, "ahb-iep", "ahb",
+ 0x064, BIT(19), 0);
+static SUNXI_CCU_GATE(ahb_gpu_clk, "ahb-gpu", "ahb",
+ 0x064, BIT(20), 0);
+
+static SUNXI_CCU_GATE(apb0_codec_clk, "apb0-codec", "apb0",
+ 0x068, BIT(0), 0);
+static SUNXI_CCU_GATE(apb0_spdif_clk, "apb0-spdif", "apb0",
+ 0x068, BIT(1), 0);
+static SUNXI_CCU_GATE(apb0_i2s_clk, "apb0-i2s", "apb0",
+ 0x068, BIT(3), 0);
+static SUNXI_CCU_GATE(apb0_pio_clk, "apb0-pio", "apb0",
+ 0x068, BIT(5), 0);
+static SUNXI_CCU_GATE(apb0_ir_clk, "apb0-ir", "apb0",
+ 0x068, BIT(6), 0);
+static SUNXI_CCU_GATE(apb0_keypad_clk, "apb0-keypad", "apb0",
+ 0x068, BIT(10), 0);
+
+static SUNXI_CCU_GATE(apb1_i2c0_clk, "apb1-i2c0", "apb1",
+ 0x06c, BIT(0), 0);
+static SUNXI_CCU_GATE(apb1_i2c1_clk, "apb1-i2c1", "apb1",
+ 0x06c, BIT(1), 0);
+static SUNXI_CCU_GATE(apb1_i2c2_clk, "apb1-i2c2", "apb1",
+ 0x06c, BIT(2), 0);
+static SUNXI_CCU_GATE(apb1_uart0_clk, "apb1-uart0", "apb1",
+ 0x06c, BIT(16), 0);
+static SUNXI_CCU_GATE(apb1_uart1_clk, "apb1-uart1", "apb1",
+ 0x06c, BIT(17), 0);
+static SUNXI_CCU_GATE(apb1_uart2_clk, "apb1-uart2", "apb1",
+ 0x06c, BIT(18), 0);
+static SUNXI_CCU_GATE(apb1_uart3_clk, "apb1-uart3", "apb1",
+ 0x06c, BIT(19), 0);
+
+static const char * const mod0_default_parents[] = { "hosc", "pll-periph",
+ "pll-ddr-other" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(nand_clk, "nand", mod0_default_parents, 0x080,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc0_clk, "mmc0", mod0_default_parents, 0x088,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc1_clk, "mmc1", mod0_default_parents, 0x08c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(mmc2_clk, "mmc2", mod0_default_parents, 0x090,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ts_clk, "ts", mod0_default_parents, 0x098,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ss_clk, "ss", mod0_default_parents, 0x09c,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi0_clk, "spi0", mod0_default_parents, 0x0a0,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi1_clk, "spi1", mod0_default_parents, 0x0a4,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(spi2_clk, "spi2", mod0_default_parents, 0x0a8,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static SUNXI_CCU_MP_WITH_MUX_GATE(ir_clk, "ir", mod0_default_parents, 0x0b0,
+ 0, 4, /* M */
+ 16, 2, /* P */
+ 24, 2, /* mux */
+ BIT(31), /* gate */
+ 0);
+
+static const char * const i2s_parents[] = { "pll-audio-8x", "pll-audio-4x",
+ "pll-audio-2x", "pll-audio" };
+static SUNXI_CCU_MUX_WITH_GATE(i2s_clk, "i2s", i2s_parents,
+ 0x0b8, 16, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static const char * const spdif_parents[] = { "pll-audio-8x", "pll-audio-4x",
+ "pll-audio-2x", "pll-audio" };
+static SUNXI_CCU_MUX_WITH_GATE(spdif_clk, "spdif", spdif_parents,
+ 0x0c0, 16, 2, BIT(31), 0);
+
+static const char * const keypad_parents[] = { "hosc", "losc"};
+static const u8 keypad_table[] = { 0, 2 };
+static struct ccu_mp keypad_clk = {
+ .enable = BIT(31),
+ .m = _SUNXI_CCU_DIV(8, 5),
+ .p = _SUNXI_CCU_DIV(20, 2),
+ .mux = _SUNXI_CCU_MUX_TABLE(24, 2, keypad_table),
+
+ .common = {
+ .reg = 0x0c4,
+ .hw.init = CLK_HW_INIT_PARENTS("keypad",
+ keypad_parents,
+ &ccu_mp_ops,
+ 0),
+ },
+};
+
+static SUNXI_CCU_GATE(usb_ohci_clk, "usb-ohci", "pll-periph",
+ 0x0cc, BIT(6), 0);
+static SUNXI_CCU_GATE(usb_phy0_clk, "usb-phy0", "pll-periph",
+ 0x0cc, BIT(8), 0);
+static SUNXI_CCU_GATE(usb_phy1_clk, "usb-phy1", "pll-periph",
+ 0x0cc, BIT(9), 0);
+
+static const char * const gps_parents[] = { "hosc", "pll-periph",
+ "pll-video1", "pll-ve" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gps_clk, "gps", gps_parents,
+ 0x0d0, 0, 3, 24, 2, BIT(31), 0);
+
+static SUNXI_CCU_GATE(dram_ve_clk, "dram-ve", "pll-ddr",
+ 0x100, BIT(0), 0);
+static SUNXI_CCU_GATE(dram_csi_clk, "dram-csi", "pll-ddr",
+ 0x100, BIT(1), 0);
+static SUNXI_CCU_GATE(dram_ts_clk, "dram-ts", "pll-ddr",
+ 0x100, BIT(3), 0);
+static SUNXI_CCU_GATE(dram_tve_clk, "dram-tve", "pll-ddr",
+ 0x100, BIT(5), 0);
+static SUNXI_CCU_GATE(dram_de_fe_clk, "dram-de-fe", "pll-ddr",
+ 0x100, BIT(25), 0);
+static SUNXI_CCU_GATE(dram_de_be_clk, "dram-de-be", "pll-ddr",
+ 0x100, BIT(26), 0);
+static SUNXI_CCU_GATE(dram_ace_clk, "dram-ace", "pll-ddr",
+ 0x100, BIT(29), 0);
+static SUNXI_CCU_GATE(dram_iep_clk, "dram-iep", "pll-ddr",
+ 0x100, BIT(31), 0);
+
+static const char * const de_parents[] = { "pll-video0", "pll-video1",
+ "pll-ddr-other" };
+static SUNXI_CCU_M_WITH_MUX_GATE(de_be_clk, "de-be", de_parents,
+ 0x104, 0, 4, 24, 2, BIT(31), 0);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(de_fe_clk, "de-fe", de_parents,
+ 0x10c, 0, 4, 24, 2, BIT(31), 0);
+
+static const char * const tcon_parents[] = { "pll-video0", "pll-video1",
+ "pll-video0-2x", "pll-video1-2x" };
+static SUNXI_CCU_MUX_WITH_GATE(tcon_ch0_clk, "tcon-ch0-sclk", tcon_parents,
+ 0x118, 24, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_M_WITH_MUX_GATE(tcon_ch1_sclk2_clk, "tcon-ch1-sclk2",
+ tcon_parents,
+ 0x12c, 0, 4, 24, 2, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_M_WITH_GATE(tcon_ch1_sclk1_clk, "tcon-ch1-sclk1", "tcon-ch1-sclk2",
+ 0x12c, 11, 1, BIT(15), CLK_SET_RATE_PARENT);
+
+static const char * const csi_parents[] = { "hosc", "pll-video0", "pll-video1",
+ "pll-video0-2x", "pll-video1-2x" };
+static const u8 csi_table[] = { 0, 1, 2, 5, 6 };
+static SUNXI_CCU_M_WITH_MUX_TABLE_GATE(csi_clk, "csi",
+ csi_parents, csi_table,
+ 0x134, 0, 5, 24, 2, BIT(31), 0);
+
+static SUNXI_CCU_GATE(ve_clk, "ve", "pll-ve",
+ 0x13c, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(codec_clk, "codec", "pll-audio",
+ 0x140, BIT(31), CLK_SET_RATE_PARENT);
+
+static SUNXI_CCU_GATE(avs_clk, "avs", "hosc",
+ 0x144, BIT(31), 0);
+
+static const char * const hdmi_parents[] = { "pll-video0", "pll-video0-2x" };
+static const u8 hdmi_table[] = { 0, 2 };
+static SUNXI_CCU_M_WITH_MUX_TABLE_GATE(hdmi_clk, "hdmi",
+ hdmi_parents, hdmi_table,
+ 0x150, 0, 4, 24, 2, BIT(31),
+ CLK_SET_RATE_PARENT);
+
+static const char * const gpu_parents[] = { "pll-video0", "pll-ve",
+ "pll-ddr-other", "pll-video1",
+ "pll-video1-2x" };
+static SUNXI_CCU_M_WITH_MUX_GATE(gpu_clk, "gpu", gpu_parents,
+ 0x154, 0, 4, 24, 3, BIT(31), 0);
+
+static const char * const mbus_parents[] = { "hosc", "pll-periph", "pll-ddr" };
+static SUNXI_CCU_MP_WITH_MUX_GATE(mbus_clk, "mbus", mbus_parents,
+ 0x15c, 0, 4, 16, 2, 24, 2, BIT(31), CLK_IS_CRITICAL);
+
+static SUNXI_CCU_GATE(iep_clk, "iep", "de-be",
+ 0x160, BIT(31), 0);
+
+static struct ccu_common *sun5i_a10s_ccu_clks[] = {
+ &hosc_clk.common,
+ &pll_core_clk.common,
+ &pll_audio_base_clk.common,
+ &pll_video0_clk.common,
+ &pll_ve_clk.common,
+ &pll_ddr_base_clk.common,
+ &pll_ddr_clk.common,
+ &pll_ddr_other_clk.common,
+ &pll_periph_clk.common,
+ &pll_video1_clk.common,
+ &cpu_clk.common,
+ &axi_clk.common,
+ &ahb_clk.common,
+ &apb0_clk.common,
+ &apb1_clk.common,
+ &axi_dram_clk.common,
+ &ahb_otg_clk.common,
+ &ahb_ehci_clk.common,
+ &ahb_ohci_clk.common,
+ &ahb_ss_clk.common,
+ &ahb_dma_clk.common,
+ &ahb_bist_clk.common,
+ &ahb_mmc0_clk.common,
+ &ahb_mmc1_clk.common,
+ &ahb_mmc2_clk.common,
+ &ahb_nand_clk.common,
+ &ahb_sdram_clk.common,
+ &ahb_emac_clk.common,
+ &ahb_ts_clk.common,
+ &ahb_spi0_clk.common,
+ &ahb_spi1_clk.common,
+ &ahb_spi2_clk.common,
+ &ahb_gps_clk.common,
+ &ahb_hstimer_clk.common,
+ &ahb_ve_clk.common,
+ &ahb_tve_clk.common,
+ &ahb_lcd_clk.common,
+ &ahb_csi_clk.common,
+ &ahb_hdmi_clk.common,
+ &ahb_de_be_clk.common,
+ &ahb_de_fe_clk.common,
+ &ahb_iep_clk.common,
+ &ahb_gpu_clk.common,
+ &apb0_codec_clk.common,
+ &apb0_spdif_clk.common,
+ &apb0_i2s_clk.common,
+ &apb0_pio_clk.common,
+ &apb0_ir_clk.common,
+ &apb0_keypad_clk.common,
+ &apb1_i2c0_clk.common,
+ &apb1_i2c1_clk.common,
+ &apb1_i2c2_clk.common,
+ &apb1_uart0_clk.common,
+ &apb1_uart1_clk.common,
+ &apb1_uart2_clk.common,
+ &apb1_uart3_clk.common,
+ &nand_clk.common,
+ &mmc0_clk.common,
+ &mmc1_clk.common,
+ &mmc2_clk.common,
+ &ts_clk.common,
+ &ss_clk.common,
+ &spi0_clk.common,
+ &spi1_clk.common,
+ &spi2_clk.common,
+ &ir_clk.common,
+ &i2s_clk.common,
+ &spdif_clk.common,
+ &keypad_clk.common,
+ &usb_ohci_clk.common,
+ &usb_phy0_clk.common,
+ &usb_phy1_clk.common,
+ &gps_clk.common,
+ &dram_ve_clk.common,
+ &dram_csi_clk.common,
+ &dram_ts_clk.common,
+ &dram_tve_clk.common,
+ &dram_de_fe_clk.common,
+ &dram_de_be_clk.common,
+ &dram_ace_clk.common,
+ &dram_iep_clk.common,
+ &de_be_clk.common,
+ &de_fe_clk.common,
+ &tcon_ch0_clk.common,
+ &tcon_ch1_sclk2_clk.common,
+ &tcon_ch1_sclk1_clk.common,
+ &csi_clk.common,
+ &ve_clk.common,
+ &codec_clk.common,
+ &avs_clk.common,
+ &hdmi_clk.common,
+ &gpu_clk.common,
+ &mbus_clk.common,
+ &iep_clk.common,
+};
+
+static CLK_FIXED_FACTOR(osc3M_clk, "osc3M", "hosc", 8, 1, 0);
+/* We hardcode the divider to 4 for now */
+static CLK_FIXED_FACTOR(pll_audio_clk, "pll-audio",
+ "pll-audio-base", 4, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_2x_clk, "pll-audio-2x",
+ "pll-audio-base", 2, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_4x_clk, "pll-audio-4x",
+ "pll-audio-base", 1, 1, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_audio_8x_clk, "pll-audio-8x",
+ "pll-audio-base", 1, 2, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_video0_2x_clk, "pll-video0-2x",
+ "pll-video0", 1, 2, CLK_SET_RATE_PARENT);
+static CLK_FIXED_FACTOR(pll_video1_2x_clk, "pll-video1-2x",
+ "pll-video1", 1, 2, CLK_SET_RATE_PARENT);
+
+static struct clk_hw_onecell_data sun5i_a10s_hw_clks = {
+ .hws = {
+ [CLK_HOSC] = &hosc_clk.common.hw,
+ [CLK_OSC3M] = &osc3M_clk.hw,
+ [CLK_PLL_CORE] = &pll_core_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR_BASE] = &pll_ddr_base_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_DDR_OTHER] = &pll_ddr_other_clk.common.hw,
+ [CLK_PLL_PERIPH] = &pll_periph_clk.common.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_CPU] = &cpu_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB] = &ahb_clk.common.hw,
+ [CLK_APB0] = &apb0_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_DRAM_AXI] = &axi_dram_clk.common.hw,
+ [CLK_AHB_OTG] = &ahb_otg_clk.common.hw,
+ [CLK_AHB_EHCI] = &ahb_ehci_clk.common.hw,
+ [CLK_AHB_OHCI] = &ahb_ohci_clk.common.hw,
+ [CLK_AHB_SS] = &ahb_ss_clk.common.hw,
+ [CLK_AHB_DMA] = &ahb_dma_clk.common.hw,
+ [CLK_AHB_BIST] = &ahb_bist_clk.common.hw,
+ [CLK_AHB_MMC0] = &ahb_mmc0_clk.common.hw,
+ [CLK_AHB_MMC1] = &ahb_mmc1_clk.common.hw,
+ [CLK_AHB_MMC2] = &ahb_mmc2_clk.common.hw,
+ [CLK_AHB_NAND] = &ahb_nand_clk.common.hw,
+ [CLK_AHB_SDRAM] = &ahb_sdram_clk.common.hw,
+ [CLK_AHB_EMAC] = &ahb_emac_clk.common.hw,
+ [CLK_AHB_TS] = &ahb_ts_clk.common.hw,
+ [CLK_AHB_SPI0] = &ahb_spi0_clk.common.hw,
+ [CLK_AHB_SPI1] = &ahb_spi1_clk.common.hw,
+ [CLK_AHB_SPI2] = &ahb_spi2_clk.common.hw,
+ [CLK_AHB_GPS] = &ahb_gps_clk.common.hw,
+ [CLK_AHB_HSTIMER] = &ahb_hstimer_clk.common.hw,
+ [CLK_AHB_VE] = &ahb_ve_clk.common.hw,
+ [CLK_AHB_TVE] = &ahb_tve_clk.common.hw,
+ [CLK_AHB_LCD] = &ahb_lcd_clk.common.hw,
+ [CLK_AHB_CSI] = &ahb_csi_clk.common.hw,
+ [CLK_AHB_HDMI] = &ahb_hdmi_clk.common.hw,
+ [CLK_AHB_DE_BE] = &ahb_de_be_clk.common.hw,
+ [CLK_AHB_DE_FE] = &ahb_de_fe_clk.common.hw,
+ [CLK_AHB_IEP] = &ahb_iep_clk.common.hw,
+ [CLK_AHB_GPU] = &ahb_gpu_clk.common.hw,
+ [CLK_APB0_CODEC] = &apb0_codec_clk.common.hw,
+ [CLK_APB0_I2S] = &apb0_i2s_clk.common.hw,
+ [CLK_APB0_PIO] = &apb0_pio_clk.common.hw,
+ [CLK_APB0_IR] = &apb0_ir_clk.common.hw,
+ [CLK_APB0_KEYPAD] = &apb0_keypad_clk.common.hw,
+ [CLK_APB1_I2C0] = &apb1_i2c0_clk.common.hw,
+ [CLK_APB1_I2C1] = &apb1_i2c1_clk.common.hw,
+ [CLK_APB1_I2C2] = &apb1_i2c2_clk.common.hw,
+ [CLK_APB1_UART0] = &apb1_uart0_clk.common.hw,
+ [CLK_APB1_UART1] = &apb1_uart1_clk.common.hw,
+ [CLK_APB1_UART2] = &apb1_uart2_clk.common.hw,
+ [CLK_APB1_UART3] = &apb1_uart3_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_TS] = &ts_clk.common.hw,
+ [CLK_SS] = &ss_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_IR] = &ir_clk.common.hw,
+ [CLK_I2S] = &i2s_clk.common.hw,
+ [CLK_KEYPAD] = &keypad_clk.common.hw,
+ [CLK_USB_OHCI] = &usb_ohci_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_GPS] = &gps_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_TS] = &dram_ts_clk.common.hw,
+ [CLK_DRAM_TVE] = &dram_tve_clk.common.hw,
+ [CLK_DRAM_DE_FE] = &dram_de_fe_clk.common.hw,
+ [CLK_DRAM_DE_BE] = &dram_de_be_clk.common.hw,
+ [CLK_DRAM_ACE] = &dram_ace_clk.common.hw,
+ [CLK_DRAM_IEP] = &dram_iep_clk.common.hw,
+ [CLK_DE_BE] = &de_be_clk.common.hw,
+ [CLK_DE_FE] = &de_fe_clk.common.hw,
+ [CLK_TCON_CH0] = &tcon_ch0_clk.common.hw,
+ [CLK_TCON_CH1_SCLK] = &tcon_ch1_sclk2_clk.common.hw,
+ [CLK_TCON_CH1] = &tcon_ch1_sclk1_clk.common.hw,
+ [CLK_CSI] = &csi_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_CODEC] = &codec_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_HDMI] = &hdmi_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_IEP] = &iep_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static struct ccu_reset_map sun5i_a10s_ccu_resets[] = {
+ [RST_USB_PHY0] = { 0x0cc, BIT(0) },
+ [RST_USB_PHY1] = { 0x0cc, BIT(1) },
+
+ [RST_GPS] = { 0x0d0, BIT(30) },
+
+ [RST_DE_BE] = { 0x104, BIT(30) },
+
+ [RST_DE_FE] = { 0x10c, BIT(30) },
+
+ [RST_TVE] = { 0x118, BIT(29) },
+ [RST_LCD] = { 0x118, BIT(30) },
+
+ [RST_CSI] = { 0x134, BIT(30) },
+
+ [RST_VE] = { 0x13c, BIT(0) },
+
+ [RST_GPU] = { 0x154, BIT(30) },
+
+ [RST_IEP] = { 0x160, BIT(30) },
+};
+
+static const struct sunxi_ccu_desc sun5i_a10s_ccu_desc = {
+ .ccu_clks = sun5i_a10s_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun5i_a10s_ccu_clks),
+
+ .hw_clks = &sun5i_a10s_hw_clks,
+
+ .resets = sun5i_a10s_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun5i_a10s_ccu_resets),
+};
+
+static struct clk_hw_onecell_data sun5i_a13_hw_clks = {
+ .hws = {
+ [CLK_HOSC] = &hosc_clk.common.hw,
+ [CLK_OSC3M] = &osc3M_clk.hw,
+ [CLK_PLL_CORE] = &pll_core_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR_BASE] = &pll_ddr_base_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_DDR_OTHER] = &pll_ddr_other_clk.common.hw,
+ [CLK_PLL_PERIPH] = &pll_periph_clk.common.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_CPU] = &cpu_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB] = &ahb_clk.common.hw,
+ [CLK_APB0] = &apb0_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_DRAM_AXI] = &axi_dram_clk.common.hw,
+ [CLK_AHB_OTG] = &ahb_otg_clk.common.hw,
+ [CLK_AHB_EHCI] = &ahb_ehci_clk.common.hw,
+ [CLK_AHB_OHCI] = &ahb_ohci_clk.common.hw,
+ [CLK_AHB_SS] = &ahb_ss_clk.common.hw,
+ [CLK_AHB_DMA] = &ahb_dma_clk.common.hw,
+ [CLK_AHB_BIST] = &ahb_bist_clk.common.hw,
+ [CLK_AHB_MMC0] = &ahb_mmc0_clk.common.hw,
+ [CLK_AHB_MMC1] = &ahb_mmc1_clk.common.hw,
+ [CLK_AHB_MMC2] = &ahb_mmc2_clk.common.hw,
+ [CLK_AHB_NAND] = &ahb_nand_clk.common.hw,
+ [CLK_AHB_SDRAM] = &ahb_sdram_clk.common.hw,
+ [CLK_AHB_EMAC] = &ahb_emac_clk.common.hw,
+ [CLK_AHB_SPI0] = &ahb_spi0_clk.common.hw,
+ [CLK_AHB_SPI1] = &ahb_spi1_clk.common.hw,
+ [CLK_AHB_SPI2] = &ahb_spi2_clk.common.hw,
+ [CLK_AHB_HSTIMER] = &ahb_hstimer_clk.common.hw,
+ [CLK_AHB_VE] = &ahb_ve_clk.common.hw,
+ [CLK_AHB_TVE] = &ahb_tve_clk.common.hw,
+ [CLK_AHB_LCD] = &ahb_lcd_clk.common.hw,
+ [CLK_AHB_CSI] = &ahb_csi_clk.common.hw,
+ [CLK_AHB_DE_BE] = &ahb_de_be_clk.common.hw,
+ [CLK_AHB_DE_FE] = &ahb_de_fe_clk.common.hw,
+ [CLK_AHB_IEP] = &ahb_iep_clk.common.hw,
+ [CLK_AHB_GPU] = &ahb_gpu_clk.common.hw,
+ [CLK_APB0_CODEC] = &apb0_codec_clk.common.hw,
+ [CLK_APB0_PIO] = &apb0_pio_clk.common.hw,
+ [CLK_APB0_IR] = &apb0_ir_clk.common.hw,
+ [CLK_APB1_I2C0] = &apb1_i2c0_clk.common.hw,
+ [CLK_APB1_I2C1] = &apb1_i2c1_clk.common.hw,
+ [CLK_APB1_I2C2] = &apb1_i2c2_clk.common.hw,
+ [CLK_APB1_UART0] = &apb1_uart0_clk.common.hw,
+ [CLK_APB1_UART1] = &apb1_uart1_clk.common.hw,
+ [CLK_APB1_UART2] = &apb1_uart2_clk.common.hw,
+ [CLK_APB1_UART3] = &apb1_uart3_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_SS] = &ss_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI1] = &spi1_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_IR] = &ir_clk.common.hw,
+ [CLK_USB_OHCI] = &usb_ohci_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_TVE] = &dram_tve_clk.common.hw,
+ [CLK_DRAM_DE_FE] = &dram_de_fe_clk.common.hw,
+ [CLK_DRAM_DE_BE] = &dram_de_be_clk.common.hw,
+ [CLK_DRAM_ACE] = &dram_ace_clk.common.hw,
+ [CLK_DRAM_IEP] = &dram_iep_clk.common.hw,
+ [CLK_DE_BE] = &de_be_clk.common.hw,
+ [CLK_DE_FE] = &de_fe_clk.common.hw,
+ [CLK_TCON_CH0] = &tcon_ch0_clk.common.hw,
+ [CLK_TCON_CH1_SCLK] = &tcon_ch1_sclk2_clk.common.hw,
+ [CLK_TCON_CH1] = &tcon_ch1_sclk1_clk.common.hw,
+ [CLK_CSI] = &csi_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_CODEC] = &codec_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_IEP] = &iep_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static const struct sunxi_ccu_desc sun5i_a13_ccu_desc = {
+ .ccu_clks = sun5i_a10s_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun5i_a10s_ccu_clks),
+
+ .hw_clks = &sun5i_a13_hw_clks,
+
+ .resets = sun5i_a10s_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun5i_a10s_ccu_resets),
+};
+
+static struct clk_hw_onecell_data sun5i_gr8_hw_clks = {
+ .hws = {
+ [CLK_HOSC] = &hosc_clk.common.hw,
+ [CLK_OSC3M] = &osc3M_clk.hw,
+ [CLK_PLL_CORE] = &pll_core_clk.common.hw,
+ [CLK_PLL_AUDIO_BASE] = &pll_audio_base_clk.common.hw,
+ [CLK_PLL_AUDIO] = &pll_audio_clk.hw,
+ [CLK_PLL_AUDIO_2X] = &pll_audio_2x_clk.hw,
+ [CLK_PLL_AUDIO_4X] = &pll_audio_4x_clk.hw,
+ [CLK_PLL_AUDIO_8X] = &pll_audio_8x_clk.hw,
+ [CLK_PLL_VIDEO0] = &pll_video0_clk.common.hw,
+ [CLK_PLL_VIDEO0_2X] = &pll_video0_2x_clk.hw,
+ [CLK_PLL_VE] = &pll_ve_clk.common.hw,
+ [CLK_PLL_DDR_BASE] = &pll_ddr_base_clk.common.hw,
+ [CLK_PLL_DDR] = &pll_ddr_clk.common.hw,
+ [CLK_PLL_DDR_OTHER] = &pll_ddr_other_clk.common.hw,
+ [CLK_PLL_PERIPH] = &pll_periph_clk.common.hw,
+ [CLK_PLL_VIDEO1] = &pll_video1_clk.common.hw,
+ [CLK_PLL_VIDEO1_2X] = &pll_video1_2x_clk.hw,
+ [CLK_CPU] = &cpu_clk.common.hw,
+ [CLK_AXI] = &axi_clk.common.hw,
+ [CLK_AHB] = &ahb_clk.common.hw,
+ [CLK_APB0] = &apb0_clk.common.hw,
+ [CLK_APB1] = &apb1_clk.common.hw,
+ [CLK_DRAM_AXI] = &axi_dram_clk.common.hw,
+ [CLK_AHB_OTG] = &ahb_otg_clk.common.hw,
+ [CLK_AHB_EHCI] = &ahb_ehci_clk.common.hw,
+ [CLK_AHB_OHCI] = &ahb_ohci_clk.common.hw,
+ [CLK_AHB_SS] = &ahb_ss_clk.common.hw,
+ [CLK_AHB_DMA] = &ahb_dma_clk.common.hw,
+ [CLK_AHB_BIST] = &ahb_bist_clk.common.hw,
+ [CLK_AHB_MMC0] = &ahb_mmc0_clk.common.hw,
+ [CLK_AHB_MMC1] = &ahb_mmc1_clk.common.hw,
+ [CLK_AHB_MMC2] = &ahb_mmc2_clk.common.hw,
+ [CLK_AHB_NAND] = &ahb_nand_clk.common.hw,
+ [CLK_AHB_SDRAM] = &ahb_sdram_clk.common.hw,
+ [CLK_AHB_SPI0] = &ahb_spi0_clk.common.hw,
+ [CLK_AHB_SPI2] = &ahb_spi2_clk.common.hw,
+ [CLK_AHB_HSTIMER] = &ahb_hstimer_clk.common.hw,
+ [CLK_AHB_VE] = &ahb_ve_clk.common.hw,
+ [CLK_AHB_TVE] = &ahb_tve_clk.common.hw,
+ [CLK_AHB_LCD] = &ahb_lcd_clk.common.hw,
+ [CLK_AHB_CSI] = &ahb_csi_clk.common.hw,
+ [CLK_AHB_DE_BE] = &ahb_de_be_clk.common.hw,
+ [CLK_AHB_DE_FE] = &ahb_de_fe_clk.common.hw,
+ [CLK_AHB_IEP] = &ahb_iep_clk.common.hw,
+ [CLK_AHB_GPU] = &ahb_gpu_clk.common.hw,
+ [CLK_APB0_CODEC] = &apb0_codec_clk.common.hw,
+ [CLK_APB0_SPDIF] = &apb0_spdif_clk.common.hw,
+ [CLK_APB0_I2S] = &apb0_i2s_clk.common.hw,
+ [CLK_APB0_PIO] = &apb0_pio_clk.common.hw,
+ [CLK_APB0_IR] = &apb0_ir_clk.common.hw,
+ [CLK_APB1_I2C0] = &apb1_i2c0_clk.common.hw,
+ [CLK_APB1_I2C1] = &apb1_i2c1_clk.common.hw,
+ [CLK_APB1_I2C2] = &apb1_i2c2_clk.common.hw,
+ [CLK_APB1_UART0] = &apb1_uart0_clk.common.hw,
+ [CLK_APB1_UART1] = &apb1_uart1_clk.common.hw,
+ [CLK_APB1_UART2] = &apb1_uart2_clk.common.hw,
+ [CLK_APB1_UART3] = &apb1_uart3_clk.common.hw,
+ [CLK_NAND] = &nand_clk.common.hw,
+ [CLK_MMC0] = &mmc0_clk.common.hw,
+ [CLK_MMC1] = &mmc1_clk.common.hw,
+ [CLK_MMC2] = &mmc2_clk.common.hw,
+ [CLK_SS] = &ss_clk.common.hw,
+ [CLK_SPI0] = &spi0_clk.common.hw,
+ [CLK_SPI2] = &spi2_clk.common.hw,
+ [CLK_IR] = &ir_clk.common.hw,
+ [CLK_I2S] = &i2s_clk.common.hw,
+ [CLK_SPDIF] = &spdif_clk.common.hw,
+ [CLK_USB_OHCI] = &usb_ohci_clk.common.hw,
+ [CLK_USB_PHY0] = &usb_phy0_clk.common.hw,
+ [CLK_USB_PHY1] = &usb_phy1_clk.common.hw,
+ [CLK_DRAM_VE] = &dram_ve_clk.common.hw,
+ [CLK_DRAM_CSI] = &dram_csi_clk.common.hw,
+ [CLK_DRAM_TVE] = &dram_tve_clk.common.hw,
+ [CLK_DRAM_DE_FE] = &dram_de_fe_clk.common.hw,
+ [CLK_DRAM_DE_BE] = &dram_de_be_clk.common.hw,
+ [CLK_DRAM_ACE] = &dram_ace_clk.common.hw,
+ [CLK_DRAM_IEP] = &dram_iep_clk.common.hw,
+ [CLK_DE_BE] = &de_be_clk.common.hw,
+ [CLK_DE_FE] = &de_fe_clk.common.hw,
+ [CLK_TCON_CH0] = &tcon_ch0_clk.common.hw,
+ [CLK_TCON_CH1_SCLK] = &tcon_ch1_sclk2_clk.common.hw,
+ [CLK_TCON_CH1] = &tcon_ch1_sclk1_clk.common.hw,
+ [CLK_CSI] = &csi_clk.common.hw,
+ [CLK_VE] = &ve_clk.common.hw,
+ [CLK_CODEC] = &codec_clk.common.hw,
+ [CLK_AVS] = &avs_clk.common.hw,
+ [CLK_GPU] = &gpu_clk.common.hw,
+ [CLK_MBUS] = &mbus_clk.common.hw,
+ [CLK_IEP] = &iep_clk.common.hw,
+ },
+ .num = CLK_NUMBER,
+};
+
+static const struct sunxi_ccu_desc sun5i_gr8_ccu_desc = {
+ .ccu_clks = sun5i_a10s_ccu_clks,
+ .num_ccu_clks = ARRAY_SIZE(sun5i_a10s_ccu_clks),
+
+ .hw_clks = &sun5i_gr8_hw_clks,
+
+ .resets = sun5i_a10s_ccu_resets,
+ .num_resets = ARRAY_SIZE(sun5i_a10s_ccu_resets),
+};
+
+static void __init sun5i_ccu_init(struct device_node *node,
+ const struct sunxi_ccu_desc *desc)
+{
+ void __iomem *reg;
+ u32 val;
+
+ reg = of_io_request_and_map(node, 0, of_node_full_name(node));
+ if (IS_ERR(reg)) {
+ pr_err("%s: Could not map the clock registers\n",
+ of_node_full_name(node));
+ return;
+ }
+
+ /* Force the PLL-Audio-1x divider to 4 */
+ val = readl(reg + SUN5I_PLL_AUDIO_REG);
+ val &= ~GENMASK(19, 16);
+ writel(val | (3 << 16), reg + SUN5I_PLL_AUDIO_REG);
+
+ /*
+ * Use the peripheral PLL as the AHB parent, instead of CPU /
+ * AXI which have rate changes due to cpufreq.
+ *
+ * This is especially a big deal for the HS timer whose parent
+ * clock is AHB.
+ */
+ val = readl(reg + SUN5I_AHB_REG);
+ val &= ~GENMASK(7, 6);
+ writel(val | (2 << 6), reg + SUN5I_AHB_REG);
+
+ sunxi_ccu_probe(node, reg, desc);
+}
+
+static void __init sun5i_a10s_ccu_setup(struct device_node *node)
+{
+ sun5i_ccu_init(node, &sun5i_a10s_ccu_desc);
+}
+CLK_OF_DECLARE(sun5i_a10s_ccu, "allwinner,sun5i-a10s-ccu",
+ sun5i_a10s_ccu_setup);
+
+static void __init sun5i_a13_ccu_setup(struct device_node *node)
+{
+ sun5i_ccu_init(node, &sun5i_a13_ccu_desc);
+}
+CLK_OF_DECLARE(sun5i_a13_ccu, "allwinner,sun5i-a13-ccu",
+ sun5i_a13_ccu_setup);
+
+static void __init sun5i_gr8_ccu_setup(struct device_node *node)
+{
+ sun5i_ccu_init(node, &sun5i_gr8_ccu_desc);
+}
+CLK_OF_DECLARE(sun5i_gr8_ccu, "nextthing,gr8-ccu",
+ sun5i_gr8_ccu_setup);
diff --git a/drivers/clk/sunxi-ng/ccu-sun5i.h b/drivers/clk/sunxi-ng/ccu-sun5i.h
new file mode 100644
index 000000000000..5bacf65cc89d
--- /dev/null
+++ b/drivers/clk/sunxi-ng/ccu-sun5i.h
@@ -0,0 +1,68 @@
+/*
+ * Copyright 2016 Maxime Ripard
+ *
+ * Maxime Ripard <maxime.ripard@free-electrons.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#ifndef _CCU_SUN5I_H_
+#define _CCU_SUN5I_H_
+
+#include <dt-bindings/clock/sun5i-ccu.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
+
+/* The HOSC is exported */
+#define CLK_OSC3M 2
+#define CLK_PLL_CORE 3
+#define CLK_PLL_AUDIO_BASE 4
+#define CLK_PLL_AUDIO 5
+#define CLK_PLL_AUDIO_2X 6
+#define CLK_PLL_AUDIO_4X 7
+#define CLK_PLL_AUDIO_8X 8
+#define CLK_PLL_VIDEO0 9
+#define CLK_PLL_VIDEO0_2X 10
+#define CLK_PLL_VE 11
+#define CLK_PLL_DDR_BASE 12
+#define CLK_PLL_DDR 13
+#define CLK_PLL_DDR_OTHER 14
+#define CLK_PLL_PERIPH 15
+#define CLK_PLL_VIDEO1 16
+#define CLK_PLL_VIDEO1_2X 17
+
+/* The CPU clock is exported */
+
+#define CLK_AXI 19
+#define CLK_AHB 20
+#define CLK_APB0 21
+#define CLK_APB1 22
+#define CLK_DRAM_AXI 23
+
+/* AHB gates are exported */
+/* APB0 gates are exported */
+/* APB1 gates are exported */
+/* Modules clocks are exported */
+/* USB clocks are exported */
+/* GPS clock is exported */
+/* DRAM gates are exported */
+/* More display modules clocks are exported */
+
+#define CLK_TCON_CH1_SCLK 92
+
+/* The rest of the module clocks are exported */
+
+#define CLK_MBUS 100
+
+/* And finally the IEP clock */
+
+#define CLK_NUMBER (CLK_IEP + 1)
+
+#endif /* _CCU_SUN5I_H_ */
--
git-series 0.8.11
^ permalink raw reply related
* [PATCH v2 6/7] ARM: sun5i: Convert to CCU
From: Maxime Ripard @ 2017-01-10 7:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.8762813dc78858261716126c700983d4aee00458.1484035021.git-series.maxime.ripard@free-electrons.com>
Now that we have drivers for all of them, convert all the SoCs that share
the sun5i DTSI to the new CCU driver.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
arch/arm/boot/dts/sun5i-a10s.dtsi | 85 +------
arch/arm/boot/dts/sun5i-a13.dtsi | 140 +-----------
arch/arm/boot/dts/sun5i-r8.dtsi | 10 +-
arch/arm/boot/dts/sun5i.dtsi | 353 +++----------------------------
4 files changed, 75 insertions(+), 513 deletions(-)
diff --git a/arch/arm/boot/dts/sun5i-a10s.dtsi b/arch/arm/boot/dts/sun5i-a10s.dtsi
index 62b3ffe62df2..24b0f5f556f8 100644
--- a/arch/arm/boot/dts/sun5i-a10s.dtsi
+++ b/arch/arm/boot/dts/sun5i-a10s.dtsi
@@ -65,8 +65,9 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-hdmi";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 43>, <&ahb_gates 44>;
+ clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_HDMI>,
+ <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DRAM_DE_BE>,
+ <&ccu CLK_DE_BE>, <&ccu CLK_HDMI>;
status = "disabled";
};
@@ -74,8 +75,8 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 36>,
- <&ahb_gates 44>;
+ clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_TCON_CH0>, <&ccu CLK_DRAM_DE_BE>;
status = "disabled";
};
@@ -83,77 +84,19 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&pll3>, <&pll5 1>, <&ahb_gates 34>,
- <&ahb_gates 36>, <&ahb_gates 44>;
+ clocks = <&ccu CLK_AHB_TVE>, <&ccu CLK_AHB_LCD>,
+ <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_TCON_CH1>, <&ccu CLK_DRAM_DE_BE>;
status = "disabled";
};
};
- clocks {
- ahb_gates: clk at 01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a10s-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <13>,
- <14>, <17>, <18>,
- <20>, <21>, <22>,
- <26>, <28>, <32>,
- <34>, <36>, <40>,
- <43>, <44>,
- <46>, <51>,
- <52>;
- clock-output-names = "ahb_usbotg", "ahb_ehci",
- "ahb_ohci", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_nand",
- "ahb_sdram", "ahb_emac", "ahb_ts",
- "ahb_spi0", "ahb_spi1", "ahb_spi2",
- "ahb_gps", "ahb_stimer", "ahb_ve",
- "ahb_tve", "ahb_lcd", "ahb_csi",
- "ahb_hdmi", "ahb_de_be",
- "ahb_de_fe", "ahb_iep",
- "ahb_mali400";
- };
-
- apb0_gates: clk at 01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a10s-apb0-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <3>,
- <5>, <6>,
- <10>;
- clock-output-names = "apb0_codec", "apb0_iis",
- "apb0_pio", "apb0_ir",
- "apb0_keypad";
- };
-
- apb1_gates: clk at 01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a10s-apb1-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <16>,
- <17>, <18>,
- <19>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_uart0",
- "apb1_uart1", "apb1_uart2",
- "apb1_uart3";
- };
- };
-
soc at 01c00000 {
emac: ethernet at 01c0b000 {
compatible = "allwinner,sun4i-a10-emac";
reg = <0x01c0b000 0x1000>;
interrupts = <55>;
- clocks = <&ahb_gates 17>;
+ clocks = <&ccu CLK_AHB_EMAC>;
allwinner,sram = <&emac_sram 1>;
status = "disabled";
};
@@ -169,7 +112,7 @@
pwm: pwm at 01c20e00 {
compatible = "allwinner,sun5i-a10s-pwm";
reg = <0x01c20e00 0xc>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
#pwm-cells = <3>;
status = "disabled";
};
@@ -180,7 +123,7 @@
interrupts = <1>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 16>;
+ clocks = <&ccu CLK_APB1_UART0>;
status = "disabled";
};
@@ -190,12 +133,16 @@
interrupts = <3>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 18>;
+ clocks = <&ccu CLK_APB1_UART2>;
status = "disabled";
};
};
};
+&ccu {
+ compatible = "allwinner,sun5i-a10s-ccu";
+};
+
&pio {
compatible = "allwinner,sun5i-a10s-pinctrl";
diff --git a/arch/arm/boot/dts/sun5i-a13.dtsi b/arch/arm/boot/dts/sun5i-a13.dtsi
index 4131ab44558b..fb2ddb9a04c9 100644
--- a/arch/arm/boot/dts/sun5i-a13.dtsi
+++ b/arch/arm/boot/dts/sun5i-a13.dtsi
@@ -61,8 +61,8 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0";
- clocks = <&ahb_gates 36>, <&ahb_gates 44>, <&de_be_clk>,
- <&tcon_ch0_clk>, <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_LCD>, <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_TCON_CH0>, <&ccu CLK_DRAM_DE_BE>;
status = "disabled";
};
};
@@ -99,114 +99,6 @@
};
};
- clocks {
- ahb_gates: clk at 01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <13>,
- <14>, <20>,
- <21>, <22>,
- <28>, <32>, <34>,
- <36>, <40>, <44>,
- <46>, <51>,
- <52>;
- clock-output-names = "ahb_usbotg", "ahb_ehci",
- "ahb_ohci", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_nand",
- "ahb_sdram", "ahb_spi0",
- "ahb_spi1", "ahb_spi2",
- "ahb_stimer", "ahb_ve", "ahb_tve",
- "ahb_lcd", "ahb_csi", "ahb_de_be",
- "ahb_de_fe", "ahb_iep",
- "ahb_mali400";
- };
-
- apb0_gates: clk at 01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-apb0-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <5>,
- <6>;
- clock-output-names = "apb0_codec", "apb0_pio",
- "apb0_ir";
- };
-
- apb1_gates: clk at 01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-apb1-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <17>,
- <19>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_uart1",
- "apb1_uart3";
- };
-
- dram_gates: clk at 01c20100 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-dram-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c20100 0x4>;
- clocks = <&pll5 0>;
- clock-indices = <0>,
- <1>,
- <25>,
- <26>,
- <29>,
- <31>;
- clock-output-names = "dram_ve",
- "dram_csi",
- "dram_de_fe",
- "dram_de_be",
- "dram_ace",
- "dram_iep";
- };
-
- de_be_clk: clk at 01c20104 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20104 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-be";
- };
-
- de_fe_clk: clk at 01c2010c {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c2010c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-fe";
- };
-
- tcon_ch0_clk: clk at 01c20118 {
- #clock-cells = <0>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
- reg = <0x01c20118 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch0-sclk";
- };
-
- tcon_ch1_clk: clk at 01c2012c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
- reg = <0x01c2012c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch1-sclk";
- };
- };
-
display-engine {
compatible = "allwinner,sun5i-a13-display-engine";
allwinner,pipelines = <&fe0>;
@@ -217,11 +109,11 @@
compatible = "allwinner,sun5i-a13-tcon";
reg = <0x01c0c000 0x1000>;
interrupts = <44>;
- resets = <&tcon_ch0_clk 1>;
+ resets = <&ccu RST_LCD>;
reset-names = "lcd";
- clocks = <&ahb_gates 36>,
- <&tcon_ch0_clk>,
- <&tcon_ch1_clk>;
+ clocks = <&ccu CLK_AHB_LCD>,
+ <&ccu CLK_TCON_CH0>,
+ <&ccu CLK_TCON_CH1>;
clock-names = "ahb",
"tcon-ch0",
"tcon-ch1";
@@ -254,7 +146,7 @@
pwm: pwm at 01c20e00 {
compatible = "allwinner,sun5i-a13-pwm";
reg = <0x01c20e00 0xc>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
#pwm-cells = <3>;
status = "disabled";
};
@@ -263,11 +155,11 @@
compatible = "allwinner,sun5i-a13-display-frontend";
reg = <0x01e00000 0x20000>;
interrupts = <47>;
- clocks = <&ahb_gates 46>, <&de_fe_clk>,
- <&dram_gates 25>;
+ clocks = <&ccu CLK_DE_FE>, <&ccu CLK_DE_FE>,
+ <&ccu CLK_DRAM_DE_FE>;
clock-names = "ahb", "mod",
"ram";
- resets = <&de_fe_clk>;
+ resets = <&ccu RST_DE_FE>;
status = "disabled";
ports {
@@ -290,14 +182,14 @@
be0: display-backend at 01e60000 {
compatible = "allwinner,sun5i-a13-display-backend";
reg = <0x01e60000 0x10000>;
- clocks = <&ahb_gates 44>, <&de_be_clk>,
- <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>;
clock-names = "ahb", "mod",
"ram";
- resets = <&de_be_clk>;
+ resets = <&ccu RST_DE_BE>;
status = "disabled";
- assigned-clocks = <&de_be_clk>;
+ assigned-clocks = <&ccu CLK_DE_BE>;
assigned-clock-rates = <300000000>;
ports {
@@ -330,6 +222,10 @@
};
};
+&ccu {
+ compatible = "allwinner,sun5i-a13-ccu";
+};
+
&cpu0 {
clock-latency = <244144>; /* 8 32k periods */
operating-points = <
diff --git a/arch/arm/boot/dts/sun5i-r8.dtsi b/arch/arm/boot/dts/sun5i-r8.dtsi
index 8b058f53b7dc..4c1141396c99 100644
--- a/arch/arm/boot/dts/sun5i-r8.dtsi
+++ b/arch/arm/boot/dts/sun5i-r8.dtsi
@@ -51,9 +51,9 @@
compatible = "allwinner,simple-framebuffer",
"simple-framebuffer";
allwinner,pipeline = "de_be0-lcd0-tve0";
- clocks = <&ahb_gates 34>, <&ahb_gates 36>,
- <&ahb_gates 44>, <&de_be_clk>,
- <&tcon_ch1_clk>, <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_TVE>, <&ccu CLK_AHB_LCD>,
+ <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_TCON_CH1>, <&ccu CLK_DRAM_DE_BE>;
status = "disabled";
};
};
@@ -62,8 +62,8 @@
tve0: tv-encoder at 01c0a000 {
compatible = "allwinner,sun4i-a10-tv-encoder";
reg = <0x01c0a000 0x1000>;
- clocks = <&ahb_gates 34>;
- resets = <&tcon_ch0_clk 0>;
+ clocks = <&ccu CLK_AHB_TVE>;
+ resets = <&ccu RST_TVE>;
status = "disabled";
port {
diff --git a/arch/arm/boot/dts/sun5i.dtsi b/arch/arm/boot/dts/sun5i.dtsi
index c058d37d5433..a9574a6cd95c 100644
--- a/arch/arm/boot/dts/sun5i.dtsi
+++ b/arch/arm/boot/dts/sun5i.dtsi
@@ -44,9 +44,10 @@
#include "skeleton.dtsi"
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include <dt-bindings/clock/sun5i-ccu.h>
#include <dt-bindings/dma/sun4i-a10.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
/ {
interrupt-parent = <&intc>;
@@ -59,7 +60,7 @@
device_type = "cpu";
compatible = "arm,cortex-a8";
reg = <0x0>;
- clocks = <&cpu>;
+ clocks = <&ccu CLK_CPU>;
};
};
@@ -68,291 +69,19 @@
#size-cells = <1>;
ranges;
- /*
- * This is a dummy clock, to be used as placeholder on
- * other mux clocks when a specific parent clock is not
- * yet implemented. It should be dropped when the driver
- * is complete.
- */
- dummy: dummy {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- };
-
osc24M: clk at 01c20050 {
#clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-osc-clk";
- reg = <0x01c20050 0x4>;
+ compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
- osc3M: osc3M_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <8>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "osc3M";
- };
-
osc32k: clk at 0 {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
-
- pll1: clk at 01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- pll2: clk at 01c20008 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-pll2-clk";
- reg = <0x01c20008 0x8>;
- clocks = <&osc24M>;
- clock-output-names = "pll2-1x", "pll2-2x",
- "pll2-4x", "pll2-8x";
- };
-
- pll3: clk at 01c20010 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20010 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll3";
- };
-
- pll3x2: pll3x2_clk {
- compatible = "allwinner,sun4i-a10-pll3-2x-clk", "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll3>;
- clock-output-names = "pll3-2x";
- };
-
- pll4: clk at 01c20018 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20018 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll4";
- };
-
- pll5: clk at 01c20020 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll5-clk";
- reg = <0x01c20020 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll5_ddr", "pll5_other";
- };
-
- pll6: clk at 01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6_sata", "pll6_other", "pll6";
- };
-
- pll7: clk at 01c20030 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20030 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll7";
- };
-
- pll7x2: pll7x2_clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll7>;
- clock-output-names = "pll7-2x";
- };
-
- /* dummy is 200M */
- cpu: cpu at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
- clock-output-names = "cpu";
- };
-
- axi: axi at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb: ahb at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-ahb-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&axi>, <&cpu>, <&pll6 1>;
- clock-output-names = "ahb";
- /*
- * Use PLL6 as parent, instead of CPU/AXI
- * which has rate changes due to cpufreq
- */
- assigned-clocks = <&ahb>;
- assigned-clock-parents = <&pll6 1>;
- };
-
- apb0: apb0 at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb>;
- clock-output-names = "apb0";
- };
-
- apb1: clk at 01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
- clock-output-names = "apb1";
- };
-
- axi_gates: clk at 01c2005c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-axi-gates-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&axi>;
- clock-indices = <0>;
- clock-output-names = "axi_dram";
- };
-
- nand_clk: clk at 01c20080 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20080 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "nand";
- };
-
- ms_clk: clk at 01c20084 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20084 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ms";
- };
-
- mmc0_clk: clk at 01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk at 01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk at 01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- ts_clk: clk at 01c20098 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20098 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ts";
- };
-
- ss_clk: clk at 01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ss";
- };
-
- spi0_clk: clk at 01c200a0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi0";
- };
-
- spi1_clk: clk at 01c200a4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi1";
- };
-
- spi2_clk: clk at 01c200a8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a8 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi2";
- };
-
- ir0_clk: clk at 01c200b0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200b0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ir0";
- };
-
- usb_clk: clk at 01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun5i-a13-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&pll6 1>;
- clock-output-names = "usb_ohci0", "usb_phy";
- };
-
- codec_clk: clk at 01c20140 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-codec-clk";
- reg = <0x01c20140 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "codec";
- };
-
- mbus_clk: clk at 01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mbus";
- };
};
soc at 01c00000 {
@@ -395,7 +124,7 @@
compatible = "allwinner,sun4i-a10-dma";
reg = <0x01c02000 0x1000>;
interrupts = <27>;
- clocks = <&ahb_gates 6>;
+ clocks = <&ccu CLK_AHB_DMA>;
#dma-cells = <2>;
};
@@ -403,7 +132,7 @@
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
interrupts = <10>;
- clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clocks = <&ccu CLK_AHB_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 27>,
<&dma SUN4I_DMA_DEDICATED 26>;
@@ -417,7 +146,7 @@
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>;
interrupts = <11>;
- clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clocks = <&ccu CLK_AHB_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 9>,
<&dma SUN4I_DMA_DEDICATED 8>;
@@ -430,14 +159,8 @@
mmc0: mmc at 01c0f000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
interrupts = <32>;
status = "disabled";
#address-cells = <1>;
@@ -447,14 +170,8 @@
mmc1: mmc at 01c10000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
interrupts = <33>;
status = "disabled";
#address-cells = <1>;
@@ -464,14 +181,8 @@
mmc2: mmc at 01c11000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
interrupts = <34>;
status = "disabled";
#address-cells = <1>;
@@ -481,7 +192,7 @@
usb_otg: usb at 01c13000 {
compatible = "allwinner,sun4i-a10-musb";
reg = <0x01c13000 0x0400>;
- clocks = <&ahb_gates 0>;
+ clocks = <&ccu CLK_AHB_OTG>;
interrupts = <38>;
interrupt-names = "mc";
phys = <&usbphy 0>;
@@ -496,9 +207,9 @@
compatible = "allwinner,sun5i-a13-usb-phy";
reg = <0x01c13400 0x10 0x01c14800 0x4>;
reg-names = "phy_ctrl", "pmu1";
- clocks = <&usb_clk 8>;
+ clocks = <&ccu CLK_USB_PHY0>;
clock-names = "usb_phy";
- resets = <&usb_clk 0>, <&usb_clk 1>;
+ resets = <&ccu RST_USB_PHY0>, <&ccu RST_USB_PHY1>;
reset-names = "usb0_reset", "usb1_reset";
status = "disabled";
};
@@ -507,7 +218,7 @@
compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
reg = <0x01c14000 0x100>;
interrupts = <39>;
- clocks = <&ahb_gates 1>;
+ clocks = <&ccu CLK_AHB_EHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -517,7 +228,7 @@
compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
reg = <0x01c14400 0x100>;
interrupts = <40>;
- clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ clocks = <&ccu CLK_USB_OHCI>, <&ccu CLK_AHB_OHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -527,7 +238,7 @@
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
interrupts = <12>;
- clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clocks = <&ccu CLK_AHB_SPI2>, <&ccu CLK_SPI2>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 29>,
<&dma SUN4I_DMA_DEDICATED 28>;
@@ -537,6 +248,14 @@
#size-cells = <0>;
};
+ ccu: clock at 01c20000 {
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
intc: interrupt-controller at 01c20400 {
compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
@@ -547,7 +266,7 @@
pio: pinctrl at 01c20800 {
reg = <0x01c20800 0x400>;
interrupts = <28>;
- clocks = <&apb0_gates 5>, <&osc24M>, <&osc32k>;
+ clocks = <&ccu CLK_APB0_PIO>, <&osc24M>, <&osc32k>;
clock-names = "apb", "hosc", "losc";
gpio-controller;
interrupt-controller;
@@ -632,7 +351,7 @@
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
};
wdt: watchdog at 01c20c90 {
@@ -652,7 +371,7 @@
compatible = "allwinner,sun4i-a10-codec";
reg = <0x01c22c00 0x40>;
interrupts = <30>;
- clocks = <&apb0_gates 0>, <&codec_clk>;
+ clocks = <&ccu CLK_APB0_CODEC>, <&ccu CLK_CODEC>;
clock-names = "apb", "codec";
dmas = <&dma SUN4I_DMA_NORMAL 19>,
<&dma SUN4I_DMA_NORMAL 19>;
@@ -678,7 +397,7 @@
interrupts = <2>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 17>;
+ clocks = <&ccu CLK_APB1_UART1>;
status = "disabled";
};
@@ -688,7 +407,7 @@
interrupts = <4>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 19>;
+ clocks = <&ccu CLK_APB1_UART3>;
status = "disabled";
};
@@ -696,7 +415,7 @@
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <7>;
- clocks = <&apb1_gates 0>;
+ clocks = <&ccu CLK_APB1_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -706,7 +425,7 @@
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <8>;
- clocks = <&apb1_gates 1>;
+ clocks = <&ccu CLK_APB1_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -716,7 +435,7 @@
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <9>;
- clocks = <&apb1_gates 2>;
+ clocks = <&ccu CLK_APB1_I2C2>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -726,7 +445,7 @@
compatible = "allwinner,sun5i-a13-hstimer";
reg = <0x01c60000 0x1000>;
interrupts = <82>, <83>;
- clocks = <&ahb_gates 28>;
+ clocks = <&ccu CLK_AHB_HSTIMER>;
};
};
};
--
git-series 0.8.11
^ permalink raw reply related
* [PATCH v2 7/7] ARM: gr8: Convert to CCU
From: Maxime Ripard @ 2017-01-10 7:57 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cover.8762813dc78858261716126c700983d4aee00458.1484035021.git-series.maxime.ripard@free-electrons.com>
Now that we have a driver for the GR8, we can convert our DT to it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
---
arch/arm/boot/dts/sun5i-gr8.dtsi | 520 +++-----------------------------
1 file changed, 56 insertions(+), 464 deletions(-)
diff --git a/arch/arm/boot/dts/sun5i-gr8.dtsi b/arch/arm/boot/dts/sun5i-gr8.dtsi
index f83ae3fc6329..cb9b2aaf7297 100644
--- a/arch/arm/boot/dts/sun5i-gr8.dtsi
+++ b/arch/arm/boot/dts/sun5i-gr8.dtsi
@@ -42,9 +42,10 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/
-#include <dt-bindings/clock/sun4i-a10-pll2.h>
+#include <dt-bindings/clock/sun5i-ccu.h>
#include <dt-bindings/dma/sun4i-a10.h>
#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include <dt-bindings/reset/sun5i-ccu.h>
/ {
interrupt-parent = <&intc>;
@@ -59,7 +60,7 @@
device_type = "cpu";
compatible = "arm,cortex-a8";
reg = <0x0>;
- clocks = <&cpu>;
+ clocks = <&ccu CLK_CPU>;
};
};
@@ -68,419 +69,19 @@
#size-cells = <1>;
ranges;
- /*
- * This is a dummy clock, to be used as placeholder on
- * other mux clocks when a specific parent clock is not
- * yet implemented. It should be dropped when the driver
- * is complete.
- */
- dummy: dummy {
- #clock-cells = <0>;
- compatible = "fixed-clock";
- clock-frequency = <0>;
- };
-
osc24M: clk at 01c20050 {
#clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-osc-clk";
- reg = <0x01c20050 0x4>;
+ compatible = "fixed-clock";
clock-frequency = <24000000>;
clock-output-names = "osc24M";
};
- osc3M: osc3M-clk {
- compatible = "fixed-factor-clock";
- #clock-cells = <0>;
- clock-div = <8>;
- clock-mult = <1>;
- clocks = <&osc24M>;
- clock-output-names = "osc3M";
- };
-
osc32k: clk at 0 {
#clock-cells = <0>;
compatible = "fixed-clock";
clock-frequency = <32768>;
clock-output-names = "osc32k";
};
-
- pll1: clk at 01c20000 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20000 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll1";
- };
-
- pll2: clk at 01c20008 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-pll2-clk";
- reg = <0x01c20008 0x8>;
- clocks = <&osc24M>;
- clock-output-names = "pll2-1x", "pll2-2x",
- "pll2-4x", "pll2-8x";
- };
-
- pll3: clk at 01c20010 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20010 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll3";
- };
-
- pll3x2: pll3x2-clk {
- compatible = "allwinner,sun4i-a10-pll3-2x-clk";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll3>;
- clock-output-names = "pll3-2x";
- };
-
- pll4: clk at 01c20018 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll1-clk";
- reg = <0x01c20018 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll4";
- };
-
- pll5: clk at 01c20020 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll5-clk";
- reg = <0x01c20020 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll5_ddr", "pll5_other";
- };
-
- pll6: clk at 01c20028 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-pll6-clk";
- reg = <0x01c20028 0x4>;
- clocks = <&osc24M>;
- clock-output-names = "pll6_sata", "pll6_other", "pll6";
- };
-
- pll7: clk at 01c20030 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-pll3-clk";
- reg = <0x01c20030 0x4>;
- clocks = <&osc3M>;
- clock-output-names = "pll7";
- };
-
- pll7x2: pll7x2-clk {
- compatible = "allwinner,sun4i-a10-pll3-2x-clk";
- #clock-cells = <0>;
- clock-div = <1>;
- clock-mult = <2>;
- clocks = <&pll7>;
- clock-output-names = "pll7-2x";
- };
-
- /* dummy is 200M */
- cpu: cpu at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-cpu-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&osc32k>, <&osc24M>, <&pll1>, <&dummy>;
- clock-output-names = "cpu";
- };
-
- axi: axi at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-axi-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&cpu>;
- clock-output-names = "axi";
- };
-
- ahb: ahb at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-ahb-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&axi>, <&cpu>, <&pll6 1>;
- clock-output-names = "ahb";
- /*
- * Use PLL6 as parent, instead of CPU/AXI
- * which has rate changes due to cpufreq
- */
- assigned-clocks = <&ahb>;
- assigned-clock-parents = <&pll6 1>;
- };
-
- apb0: apb0 at 01c20054 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb0-clk";
- reg = <0x01c20054 0x4>;
- clocks = <&ahb>;
- clock-output-names = "apb0";
- };
-
- apb1: clk at 01c20058 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-apb1-clk";
- reg = <0x01c20058 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&osc32k>;
- clock-output-names = "apb1";
- };
-
- axi_gates: clk at 01c2005c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c2005c 0x4>;
- clocks = <&axi>;
- clock-indices = <0>;
- clock-output-names = "axi_dram";
- };
-
- ahb_gates: clk at 01c20060 {
- #clock-cells = <1>;
- compatible = "allwinner,sun5i-a13-ahb-gates-clk";
- reg = <0x01c20060 0x8>;
- clocks = <&ahb>;
- clock-indices = <0>, <1>,
- <2>, <5>, <6>,
- <7>, <8>, <9>,
- <10>, <13>,
- <14>, <17>, <20>,
- <21>, <22>,
- <28>, <32>, <34>,
- <36>, <40>, <44>,
- <46>, <51>,
- <52>;
- clock-output-names = "ahb_usbotg", "ahb_ehci",
- "ahb_ohci", "ahb_ss", "ahb_dma",
- "ahb_bist", "ahb_mmc0", "ahb_mmc1",
- "ahb_mmc2", "ahb_nand",
- "ahb_sdram", "ahb_emac", "ahb_spi0",
- "ahb_spi1", "ahb_spi2",
- "ahb_hstimer", "ahb_ve", "ahb_tve",
- "ahb_lcd", "ahb_csi", "ahb_de_be",
- "ahb_de_fe", "ahb_iep",
- "ahb_mali400";
- };
-
- apb0_gates: clk at 01c20068 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c20068 0x4>;
- clocks = <&apb0>;
- clock-indices = <0>, <3>,
- <5>, <6>;
- clock-output-names = "apb0_codec", "apb0_i2s0",
- "apb0_pio", "apb0_ir";
- };
-
- apb1_gates: clk at 01c2006c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c2006c 0x4>;
- clocks = <&apb1>;
- clock-indices = <0>, <1>,
- <2>, <17>,
- <18>, <19>;
- clock-output-names = "apb1_i2c0", "apb1_i2c1",
- "apb1_i2c2", "apb1_uart1",
- "apb1_uart2", "apb1_uart3";
- };
-
- nand_clk: clk at 01c20080 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20080 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "nand";
- };
-
- ms_clk: clk at 01c20084 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20084 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ms";
- };
-
- mmc0_clk: clk at 01c20088 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20088 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc0",
- "mmc0_output",
- "mmc0_sample";
- };
-
- mmc1_clk: clk at 01c2008c {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c2008c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc1",
- "mmc1_output",
- "mmc1_sample";
- };
-
- mmc2_clk: clk at 01c20090 {
- #clock-cells = <1>;
- compatible = "allwinner,sun4i-a10-mmc-clk";
- reg = <0x01c20090 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mmc2",
- "mmc2_output",
- "mmc2_sample";
- };
-
- ts_clk: clk at 01c20098 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c20098 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ts";
- };
-
- ss_clk: clk at 01c2009c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c2009c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ss";
- };
-
- spi0_clk: clk at 01c200a0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi0";
- };
-
- spi1_clk: clk at 01c200a4 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a4 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi1";
- };
-
- spi2_clk: clk at 01c200a8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200a8 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "spi2";
- };
-
- ir0_clk: clk at 01c200b0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod0-clk";
- reg = <0x01c200b0 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "ir0";
- };
-
- i2s0_clk: clk at 01c200b8 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod1-clk";
- reg = <0x01c200b8 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_8X>,
- <&pll2 SUN4I_A10_PLL2_4X>,
- <&pll2 SUN4I_A10_PLL2_2X>,
- <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "i2s0";
- };
-
- spdif_clk: clk at 01c200c0 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-mod1-clk";
- reg = <0x01c200c0 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_8X>,
- <&pll2 SUN4I_A10_PLL2_4X>,
- <&pll2 SUN4I_A10_PLL2_2X>,
- <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "spdif";
- };
-
- usb_clk: clk at 01c200cc {
- #clock-cells = <1>;
- #reset-cells = <1>;
- compatible = "allwinner,sun5i-a13-usb-clk";
- reg = <0x01c200cc 0x4>;
- clocks = <&pll6 1>;
- clock-output-names = "usb_ohci0", "usb_phy";
- };
-
- dram_gates: clk at 01c20100 {
- #clock-cells = <1>;
- compatible = "nextthing,gr8-dram-gates-clk",
- "allwinner,sun4i-a10-gates-clk";
- reg = <0x01c20100 0x4>;
- clocks = <&pll5 0>;
- clock-indices = <0>,
- <1>,
- <25>,
- <26>,
- <29>,
- <31>;
- clock-output-names = "dram_ve",
- "dram_csi",
- "dram_de_fe",
- "dram_de_be",
- "dram_ace",
- "dram_iep";
- };
-
- de_be_clk: clk at 01c20104 {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c20104 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-be";
- };
-
- de_fe_clk: clk at 01c2010c {
- #clock-cells = <0>;
- #reset-cells = <0>;
- compatible = "allwinner,sun4i-a10-display-clk";
- reg = <0x01c2010c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll5 1>;
- clock-output-names = "de-fe";
- };
-
- tcon_ch0_clk: clk at 01c20118 {
- #clock-cells = <0>;
- #reset-cells = <1>;
- compatible = "allwinner,sun4i-a10-tcon-ch0-clk";
- reg = <0x01c20118 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch0-sclk";
- };
-
- tcon_ch1_clk: clk at 01c2012c {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-tcon-ch1-clk";
- reg = <0x01c2012c 0x4>;
- clocks = <&pll3>, <&pll7>, <&pll3x2>, <&pll7x2>;
- clock-output-names = "tcon-ch1-sclk";
- };
-
- codec_clk: clk at 01c20140 {
- #clock-cells = <0>;
- compatible = "allwinner,sun4i-a10-codec-clk";
- reg = <0x01c20140 0x4>;
- clocks = <&pll2 SUN4I_A10_PLL2_1X>;
- clock-output-names = "codec";
- };
-
- mbus_clk: clk at 01c2015c {
- #clock-cells = <0>;
- compatible = "allwinner,sun5i-a13-mbus-clk";
- reg = <0x01c2015c 0x4>;
- clocks = <&osc24M>, <&pll6 1>, <&pll5 1>;
- clock-output-names = "mbus";
- };
};
display-engine {
@@ -528,7 +129,7 @@
compatible = "allwinner,sun4i-a10-dma";
reg = <0x01c02000 0x1000>;
interrupts = <27>;
- clocks = <&ahb_gates 6>;
+ clocks = <&ccu CLK_AHB_DMA>;
#dma-cells = <2>;
};
@@ -536,7 +137,7 @@
compatible = "allwinner,sun4i-a10-nand";
reg = <0x01c03000 0x1000>;
interrupts = <37>;
- clocks = <&ahb_gates 13>, <&nand_clk>;
+ clocks = <&ccu CLK_AHB_NAND>, <&ccu CLK_NAND>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 3>;
dma-names = "rxtx";
@@ -549,7 +150,7 @@
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c05000 0x1000>;
interrupts = <10>;
- clocks = <&ahb_gates 20>, <&spi0_clk>;
+ clocks = <&ccu CLK_AHB_SPI0>, <&ccu CLK_SPI0>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 27>,
<&dma SUN4I_DMA_DEDICATED 26>;
@@ -563,7 +164,7 @@
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c06000 0x1000>;
interrupts = <11>;
- clocks = <&ahb_gates 21>, <&spi1_clk>;
+ clocks = <&ccu CLK_AHB_SPI1>, <&ccu CLK_SPI1>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 9>,
<&dma SUN4I_DMA_DEDICATED 8>;
@@ -576,8 +177,8 @@
tve0: tv-encoder at 01c0a000 {
compatible = "allwinner,sun4i-a10-tv-encoder";
reg = <0x01c0a000 0x1000>;
- clocks = <&ahb_gates 34>;
- resets = <&tcon_ch0_clk 0>;
+ clocks = <&ccu CLK_AHB_TVE>;
+ resets = <&ccu RST_TVE>;
status = "disabled";
port {
@@ -595,11 +196,11 @@
compatible = "allwinner,sun5i-a13-tcon";
reg = <0x01c0c000 0x1000>;
interrupts = <44>;
- resets = <&tcon_ch0_clk 1>;
+ resets = <&ccu RST_LCD>;
reset-names = "lcd";
- clocks = <&ahb_gates 36>,
- <&tcon_ch0_clk>,
- <&tcon_ch1_clk>;
+ clocks = <&ccu CLK_AHB_LCD>,
+ <&ccu CLK_TCON_CH0>,
+ <&ccu CLK_TCON_CH1>;
clock-names = "ahb",
"tcon-ch0",
"tcon-ch1";
@@ -637,14 +238,8 @@
mmc0: mmc at 01c0f000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c0f000 0x1000>;
- clocks = <&ahb_gates 8>,
- <&mmc0_clk 0>,
- <&mmc0_clk 1>,
- <&mmc0_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC0>, <&ccu CLK_MMC0>;
+ clock-names = "ahb", "mmc";
interrupts = <32>;
status = "disabled";
#address-cells = <1>;
@@ -654,14 +249,8 @@
mmc1: mmc at 01c10000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c10000 0x1000>;
- clocks = <&ahb_gates 9>,
- <&mmc1_clk 0>,
- <&mmc1_clk 1>,
- <&mmc1_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC1>, <&ccu CLK_MMC1>;
+ clock-names = "ahb", "mmc";
interrupts = <33>;
status = "disabled";
#address-cells = <1>;
@@ -671,14 +260,8 @@
mmc2: mmc at 01c11000 {
compatible = "allwinner,sun5i-a13-mmc";
reg = <0x01c11000 0x1000>;
- clocks = <&ahb_gates 10>,
- <&mmc2_clk 0>,
- <&mmc2_clk 1>,
- <&mmc2_clk 2>;
- clock-names = "ahb",
- "mmc",
- "output",
- "sample";
+ clocks = <&ccu CLK_AHB_MMC2>, <&ccu CLK_MMC2>;
+ clock-names = "ahb", "mmc";
interrupts = <34>;
status = "disabled";
#address-cells = <1>;
@@ -688,7 +271,7 @@
usb_otg: usb at 01c13000 {
compatible = "allwinner,sun4i-a10-musb";
reg = <0x01c13000 0x0400>;
- clocks = <&ahb_gates 0>;
+ clocks = <&ccu CLK_AHB_OTG>;
interrupts = <38>;
interrupt-names = "mc";
phys = <&usbphy 0>;
@@ -705,9 +288,9 @@
compatible = "allwinner,sun5i-a13-usb-phy";
reg = <0x01c13400 0x10 0x01c14800 0x4>;
reg-names = "phy_ctrl", "pmu1";
- clocks = <&usb_clk 8>;
+ clocks = <&ccu CLK_USB_PHY0>;
clock-names = "usb_phy";
- resets = <&usb_clk 0>, <&usb_clk 1>;
+ resets = <&ccu RST_USB_PHY0>, <&ccu RST_USB_PHY1>;
reset-names = "usb0_reset", "usb1_reset";
status = "disabled";
};
@@ -716,7 +299,7 @@
compatible = "allwinner,sun5i-a13-ehci", "generic-ehci";
reg = <0x01c14000 0x100>;
interrupts = <39>;
- clocks = <&ahb_gates 1>;
+ clocks = <&ccu CLK_AHB_EHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -726,7 +309,7 @@
compatible = "allwinner,sun5i-a13-ohci", "generic-ohci";
reg = <0x01c14400 0x100>;
interrupts = <40>;
- clocks = <&usb_clk 6>, <&ahb_gates 2>;
+ clocks = <&ccu CLK_USB_OHCI>, <&ccu CLK_AHB_OHCI>;
phys = <&usbphy 1>;
phy-names = "usb";
status = "disabled";
@@ -736,7 +319,7 @@
compatible = "allwinner,sun4i-a10-spi";
reg = <0x01c17000 0x1000>;
interrupts = <12>;
- clocks = <&ahb_gates 22>, <&spi2_clk>;
+ clocks = <&ccu CLK_AHB_SPI2>, <&ccu CLK_SPI2>;
clock-names = "ahb", "mod";
dmas = <&dma SUN4I_DMA_DEDICATED 29>,
<&dma SUN4I_DMA_DEDICATED 28>;
@@ -746,6 +329,15 @@
#size-cells = <0>;
};
+ ccu: clock at 01c20000 {
+ compatible = "nextthing,gr8-ccu";
+ reg = <0x01c20000 0x400>;
+ clocks = <&osc24M>, <&osc32k>;
+ clock-names = "hosc", "losc";
+ #clock-cells = <1>;
+ #reset-cells = <1>;
+ };
+
intc: interrupt-controller at 01c20400 {
compatible = "allwinner,sun4i-a10-ic";
reg = <0x01c20400 0x400>;
@@ -757,7 +349,7 @@
compatible = "nextthing,gr8-pinctrl";
reg = <0x01c20800 0x400>;
interrupts = <28>;
- clocks = <&apb0_gates 5>;
+ clocks = <&ccu CLK_APB0_PIO>;
gpio-controller;
interrupt-controller;
#interrupt-cells = <3>;
@@ -876,7 +468,7 @@
pwm: pwm at 01c20e00 {
compatible = "allwinner,sun5i-a10s-pwm";
reg = <0x01c20e00 0xc>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
#pwm-cells = <3>;
status = "disabled";
};
@@ -885,7 +477,7 @@
compatible = "allwinner,sun4i-a10-timer";
reg = <0x01c20c00 0x90>;
interrupts = <22>;
- clocks = <&osc24M>;
+ clocks = <&ccu CLK_HOSC>;
};
wdt: watchdog at 01c20c90 {
@@ -898,7 +490,7 @@
compatible = "allwinner,sun4i-a10-spdif";
reg = <0x01c21000 0x400>;
interrupts = <13>;
- clocks = <&apb0_gates 1>, <&spdif_clk>;
+ clocks = <&ccu CLK_APB0_SPDIF>, <&ccu CLK_SPDIF>;
clock-names = "apb", "spdif";
dmas = <&dma SUN4I_DMA_NORMAL 2>,
<&dma SUN4I_DMA_NORMAL 2>;
@@ -908,7 +500,7 @@
ir0: ir at 01c21800 {
compatible = "allwinner,sun4i-a10-ir";
- clocks = <&apb0_gates 6>, <&ir0_clk>;
+ clocks = <&ccu CLK_APB0_IR>, <&ccu CLK_IR>;
clock-names = "apb", "ir";
interrupts = <5>;
reg = <0x01c21800 0x40>;
@@ -920,7 +512,7 @@
compatible = "allwinner,sun4i-a10-i2s";
reg = <0x01c22400 0x400>;
interrupts = <16>;
- clocks = <&apb0_gates 3>, <&i2s0_clk>;
+ clocks = <&ccu CLK_APB0_I2S>, <&ccu CLK_I2S>;
clock-names = "apb", "mod";
dmas = <&dma SUN4I_DMA_NORMAL 3>,
<&dma SUN4I_DMA_NORMAL 3>;
@@ -940,7 +532,7 @@
compatible = "allwinner,sun4i-a10-codec";
reg = <0x01c22c00 0x40>;
interrupts = <30>;
- clocks = <&apb0_gates 0>, <&codec_clk>;
+ clocks = <&ccu CLK_APB0_CODEC>, <&ccu CLK_CODEC>;
clock-names = "apb", "codec";
dmas = <&dma SUN4I_DMA_NORMAL 19>,
<&dma SUN4I_DMA_NORMAL 19>;
@@ -961,7 +553,7 @@
interrupts = <2>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 17>;
+ clocks = <&ccu CLK_APB1_UART1>;
status = "disabled";
};
@@ -971,7 +563,7 @@
interrupts = <3>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 18>;
+ clocks = <&ccu CLK_APB1_UART2>;
status = "disabled";
};
@@ -981,7 +573,7 @@
interrupts = <4>;
reg-shift = <2>;
reg-io-width = <4>;
- clocks = <&apb1_gates 19>;
+ clocks = <&ccu CLK_APB1_UART3>;
status = "disabled";
};
@@ -989,7 +581,7 @@
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2ac00 0x400>;
interrupts = <7>;
- clocks = <&apb1_gates 0>;
+ clocks = <&ccu CLK_APB1_I2C0>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -999,7 +591,7 @@
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b000 0x400>;
interrupts = <8>;
- clocks = <&apb1_gates 1>;
+ clocks = <&ccu CLK_APB1_I2C1>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -1009,7 +601,7 @@
compatible = "allwinner,sun4i-a10-i2c";
reg = <0x01c2b400 0x400>;
interrupts = <9>;
- clocks = <&apb1_gates 2>;
+ clocks = <&ccu CLK_APB1_I2C2>;
status = "disabled";
#address-cells = <1>;
#size-cells = <0>;
@@ -1019,18 +611,18 @@
compatible = "allwinner,sun5i-a13-hstimer";
reg = <0x01c60000 0x1000>;
interrupts = <82>, <83>;
- clocks = <&ahb_gates 28>;
+ clocks = <&ccu CLK_AHB_HSTIMER>;
};
fe0: display-frontend at 01e00000 {
compatible = "allwinner,sun5i-a13-display-frontend";
reg = <0x01e00000 0x20000>;
interrupts = <47>;
- clocks = <&ahb_gates 46>, <&de_fe_clk>,
- <&dram_gates 25>;
+ clocks = <&ccu CLK_AHB_DE_FE>, <&ccu CLK_DE_FE>,
+ <&ccu CLK_DRAM_DE_FE>;
clock-names = "ahb", "mod",
"ram";
- resets = <&de_fe_clk>;
+ resets = <&ccu RST_DE_FE>;
status = "disabled";
ports {
@@ -1053,14 +645,14 @@
be0: display-backend at 01e60000 {
compatible = "allwinner,sun5i-a13-display-backend";
reg = <0x01e60000 0x10000>;
- clocks = <&ahb_gates 44>, <&de_be_clk>,
- <&dram_gates 26>;
+ clocks = <&ccu CLK_AHB_DE_BE>, <&ccu CLK_DE_BE>,
+ <&ccu CLK_DRAM_DE_BE>;
clock-names = "ahb", "mod",
"ram";
- resets = <&de_be_clk>;
+ resets = <&ccu RST_DE_BE>;
status = "disabled";
- assigned-clocks = <&de_be_clk>;
+ assigned-clocks = <&ccu CLK_DE_BE>;
assigned-clock-rates = <300000000>;
ports {
--
git-series 0.8.11
^ permalink raw reply related
* [PATCH v5 0/2] Support for Axentia TSE-850
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-arm-kernel
Hi!
changes v4 -> v5
- comment from Rob about the memory node made me look closer and
the memory size is actually updated by the bootloader, and that
hid the fact that the entry was always faulty. This version
specifies the correct memory size from the start, which is 64MB.
- ack from Rob
changes v3 -> v4
- rename files arch/arm/boot/dts/axentia-* to .../at91-*
- remove bootargs from at91-tse850-3.dts
- depend on the atmel ssc to register as a sound dai by itself
- bump copyright years
changes v2 -> v3
- document the new compatible strings prefixed with "axentia,".
changes v1 -> v2
- squash the fixup into the correct patch, sorry for the noise.
After finally having all essintial drivers upstreamed I would
like to have the dts and the defconfig also upstreamed.
The atmel-ssc/sound-dai change depends on a change that has been
sitting in the ASoC tree since mid-december, and I have been waiting
for it to hit linux-next before sending this, but it seems to take
longer than I anticipated. So, since I do not want this to in
turn miss the next merge window because of that wait I therefore
request that this is taken now even though it doesn't really work
w/o the ASoC "topic/atmel" branch as of 2016-12-15 [1]. It of course
builds cleanly even w/o those ASoC changes. That effectively means
that noone besides me should notice the inconsistency (I currently
have all affected devices under my control).
Cheers,
peda
[1] http://git.kernel.org/cgit/linux/kernel/git/broonie/sound.git/log/?h=topic/atmel
Peter Rosin (2):
ARM: dts: at91: add devicetree for the Axentia TSE-850
ARM: sama5_defconfig: add support for the Axentia TSE-850 board
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
arch/arm/configs/sama5_defconfig | 7 +-
6 files changed, 361 insertions(+), 1 deletion(-)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
--
2.1.4
^ permalink raw reply
* [PATCH v5 1/2] ARM: dts: at91: add devicetree for the Axentia TSE-850
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1484035732-31635-1-git-send-email-peda@axentia.se>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
Documentation/devicetree/bindings/arm/axentia.txt | 19 ++
MAINTAINERS | 8 +
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-linea.dtsi | 53 +++++
arch/arm/boot/dts/at91-tse850-3.dts | 274 ++++++++++++++++++++++
5 files changed, 355 insertions(+)
create mode 100644 Documentation/devicetree/bindings/arm/axentia.txt
create mode 100644 arch/arm/boot/dts/at91-linea.dtsi
create mode 100644 arch/arm/boot/dts/at91-tse850-3.dts
diff --git a/Documentation/devicetree/bindings/arm/axentia.txt b/Documentation/devicetree/bindings/arm/axentia.txt
new file mode 100644
index 000000000000..ea3fb96ae465
--- /dev/null
+++ b/Documentation/devicetree/bindings/arm/axentia.txt
@@ -0,0 +1,19 @@
+Device tree bindings for Axentia ARM devices
+============================================
+
+Linea CPU module
+----------------
+
+Required root node properties:
+compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from atmel-at91.txt for a sama5d31 SoC.
+
+
+TSE-850 v3 board
+----------------
+
+Required root node properties:
+compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+and following the rules from above for the axentia,linea CPU module.
diff --git a/MAINTAINERS b/MAINTAINERS
index 97b78cc5aa51..5c2ea6e9cd7f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2346,6 +2346,14 @@ S: Maintained
F: Documentation/devicetree/bindings/sound/axentia,*
F: sound/soc/atmel/tse850-pcm5142.c
+AXENTIA ARM DEVICES
+M: Peter Rosin <peda@axentia.se>
+L: linux-arm-kernel at lists.infradead.org (moderated for non-subscribers)
+S: Maintained
+F: Documentation/devicetree/bindings/arm/axentia.txt
+F: arch/arm/boot/dts/at91-linea.dtsi
+F: arch/arm/boot/dts/at91-tse850-3.dts
+
AZ6007 DVB DRIVER
M: Mauro Carvalho Chehab <mchehab@s-opensource.com>
M: Mauro Carvalho Chehab <mchehab@kernel.org>
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9a7375c388a8..7632849866de 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -48,6 +48,7 @@ dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
+ at91-tse850-3.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
sama5d34ek.dtb \
diff --git a/arch/arm/boot/dts/at91-linea.dtsi b/arch/arm/boot/dts/at91-linea.dtsi
new file mode 100644
index 000000000000..646feb0daa81
--- /dev/null
+++ b/arch/arm/boot/dts/at91-linea.dtsi
@@ -0,0 +1,53 @@
+/*
+ * at91-linea.dtsi - Device Tree Include file for the Axentia Linea Module.
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+
+#include "sama5d31.dtsi"
+
+/ {
+ compatible = "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ memory {
+ reg = <0x20000000 0x4000000>;
+ };
+};
+
+&slow_xtal {
+ clock-frequency = <32768>;
+};
+
+&main_xtal {
+ clock-frequency = <12000000>;
+};
+
+&main {
+ clock-frequency = <12000000>;
+};
+
+&i2c0 {
+ status = "okay";
+
+ eeprom at 51 {
+ compatible = "st,24c64";
+ reg = <0x51>;
+ pagesize = <32>;
+ };
+};
+
+&nand0 {
+ status = "okay";
+
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+};
diff --git a/arch/arm/boot/dts/at91-tse850-3.dts b/arch/arm/boot/dts/at91-tse850-3.dts
new file mode 100644
index 000000000000..669a2c6bdefc
--- /dev/null
+++ b/arch/arm/boot/dts/at91-tse850-3.dts
@@ -0,0 +1,274 @@
+/*
+ * at91-tse850-3.dts - Device Tree file for the Axentia TSE-850 3.0 board
+ *
+ * Copyright (C) 2017 Axentia Technologies AB
+ *
+ * Author: Peter Rosin <peda@axentia.se>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include <dt-bindings/pwm/pwm.h>
+#include "at91-linea.dtsi"
+
+/ {
+ model = "Axentia TSE-850 3.0";
+ compatible = "axentia,tse850v3", "axentia,linea",
+ "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ ahb {
+ apb {
+ pinctrl at fffff200 {
+ tse850 {
+ pinctrl_usba_vbus: usba-vbus {
+ atmel,pins =
+ <AT91_PIOC 31
+ AT91_PERIPH_GPIO
+ AT91_PINCTRL_DEGLITCH>;
+ };
+ };
+ };
+
+ watchdog at fffffe40 {
+ status = "okay";
+ };
+ };
+ };
+
+ sck: oscillator {
+ compatible = "fixed-clock";
+
+ #clock-cells = <0>;
+ clock-frequency = <16000000>;
+ clock-output-names = "sck";
+ };
+
+ reg_3v3: regulator {
+ compatible = "regulator-fixed";
+
+ regulator-name = "3v3-supply";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ana: reg-ana {
+ compatible = "pwm-regulator";
+
+ regulator-name = "ANA";
+
+ pwms = <&pwm0 2 1000 PWM_POLARITY_INVERTED>;
+ pwm-dutycycle-unit = <1000>;
+ pwm-dutycycle-range = <100 1000>;
+
+ regulator-min-microvolt = <2000000>;
+ regulator-max-microvolt = <20000000>;
+ regulator-ramp-delay = <1000>;
+ };
+
+ sound {
+ compatible = "axentia,tse850-pcm5142";
+
+ axentia,cpu-dai = <&ssc0>;
+ axentia,audio-codec = <&pcm5142>;
+
+ axentia,add-gpios = <&pioA 8 GPIO_ACTIVE_LOW>;
+ axentia,loop1-gpios = <&pioA 10 GPIO_ACTIVE_LOW>;
+ axentia,loop2-gpios = <&pioA 11 GPIO_ACTIVE_LOW>;
+
+ axentia,ana-supply = <&ana>;
+ };
+
+ dac: dpot-dac {
+ compatible = "dpot-dac";
+ vref-supply = <®_3v3>;
+ io-channels = <&dpot 0>;
+ io-channel-names = "dpot";
+ #io-channel-cells = <1>;
+ };
+
+ envelope-detector {
+ compatible = "axentia,tse850-envelope-detector";
+ io-channels = <&dac 0>;
+ io-channel-names = "dac";
+
+ interrupt-parent = <&pioA>;
+ interrupts = <3 IRQ_TYPE_EDGE_RISING>;
+ interrupt-names = "comp";
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ ch1-red {
+ label = "ch-1:red";
+ gpios = <&pioA 23 GPIO_ACTIVE_LOW>;
+ };
+ ch1-green {
+ label = "ch-1:green";
+ gpios = <&pioA 22 GPIO_ACTIVE_LOW>;
+ };
+ ch2-red {
+ label = "ch-2:red";
+ gpios = <&pioA 21 GPIO_ACTIVE_LOW>;
+ };
+ ch2-green {
+ label = "ch-2:green";
+ gpios = <&pioA 20 GPIO_ACTIVE_LOW>;
+ };
+ data-red {
+ label = "data:red";
+ gpios = <&pioA 19 GPIO_ACTIVE_LOW>;
+ };
+ data-green {
+ label = "data:green";
+ gpios = <&pioA 18 GPIO_ACTIVE_LOW>;
+ };
+ alarm-red {
+ label = "alarm:red";
+ gpios = <&pioA 17 GPIO_ACTIVE_LOW>;
+ };
+ alarm-green {
+ label = "alarm:green";
+ gpios = <&pioA 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&nand0 {
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x40000>;
+ };
+
+ barebox at 40000 {
+ label = "bootloader";
+ reg = <0x40000 0x60000>;
+ };
+
+ bareboxenv at c0000 {
+ label = "bareboxenv";
+ reg = <0xc0000 0x40000>;
+ };
+
+ bareboxenv2 at 100000 {
+ label = "bareboxenv2";
+ reg = <0x100000 0x40000>;
+ };
+
+ oftree at 180000 {
+ label = "oftree";
+ reg = <0x180000 0x20000>;
+ };
+
+ kernel at 200000 {
+ label = "kernel";
+ reg = <0x200000 0x500000>;
+ };
+
+ rootfs at 800000 {
+ label = "rootfs";
+ reg = <0x800000 0x0f800000>;
+ };
+
+ ovlfs at 10000000 {
+ label = "ovlfs";
+ reg = <0x10000000 0x10000000>;
+ };
+};
+
+&ssc0 {
+ #sound-dai-cells = <0>;
+
+ status = "okay";
+};
+
+&i2c0 {
+ status = "okay";
+
+ jc42 at 18 {
+ compatible = "nxp,se97b", "jedec,jc-42.4-temp";
+ reg = <0x18>;
+ };
+
+ dpot: mcp4651-104 at 28 {
+ compatible = "microchip,mcp4651-104";
+ reg = <0x28>;
+ #io-channel-cells = <1>;
+ };
+
+ pcm5142: pcm5142 at 4c {
+ compatible = "ti,pcm5142";
+
+ reg = <0x4c>;
+
+ AVDD-supply = <®_3v3>;
+ DVDD-supply = <®_3v3>;
+ CPVDD-supply = <®_3v3>;
+
+ clocks = <&sck>;
+
+ pll-in = <3>;
+ pll-out = <6>;
+ };
+
+ eeprom at 50 {
+ compatible = "nxp,24c02";
+ reg = <0x50>;
+ pagesize = <16>;
+ };
+};
+
+&usart0 {
+ status = "okay";
+
+ atmel,use-dma-rx;
+};
+
+&pwm0 {
+ status = "okay";
+
+ pinctrl-0 = <&pinctrl_pwm0_pwml2_1>;
+ pinctrl-names = "default";
+};
+
+&macb1 {
+ status = "okay";
+
+ phy-mode = "rgmii";
+
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ phy0: ethernet-phy at 3 {
+ reg = <3>;
+
+ interrupt-parent = <&pioE>;
+ interrupts = <31 IRQ_TYPE_EDGE_FALLING>;
+ };
+};
+
+&usb0 {
+ status = "okay";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ atmel,vbus-gpio = <&pioC 31 GPIO_ACTIVE_HIGH>;
+};
+
+&usb1 {
+ status = "okay";
+
+ num-ports = <1>;
+ atmel,vbus-gpio = <&pioD 29 GPIO_ACTIVE_HIGH>;
+ atmel,oc-gpio = <&pioC 15 GPIO_ACTIVE_LOW>;
+};
+
+&usb2 {
+ status = "okay";
+};
+
+&dbgu {
+ status = "okay";
+
+ dmas = <0>, <0>; /* Do not use DMA for dbgu */
+};
--
2.1.4
^ permalink raw reply related
* [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
From: Peter Rosin @ 2017-01-10 8:08 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1484035732-31635-1-git-send-email-peda@axentia.se>
Signed-off-by: Peter Rosin <peda@axentia.se>
---
arch/arm/configs/sama5_defconfig | 7 ++++++-
1 file changed, 6 insertions(+), 1 deletion(-)
diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
index aca8625b6fc9..bf5b3a73e38c 100644
--- a/arch/arm/configs/sama5_defconfig
+++ b/arch/arm/configs/sama5_defconfig
@@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
CONFIG_POWER_SUPPLY=y
CONFIG_BATTERY_ACT8945A=y
CONFIG_POWER_RESET=y
-# CONFIG_HWMON is not set
+CONFIG_SENSORS_JC42=y
CONFIG_WATCHDOG=y
CONFIG_AT91SAM9X_WATCHDOG=y
CONFIG_SAMA5D4_WATCHDOG=y
@@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
CONFIG_REGULATOR_FIXED_VOLTAGE=y
CONFIG_REGULATOR_ACT8865=y
CONFIG_REGULATOR_ACT8945A=y
+CONFIG_REGULATOR_PWM=y
CONFIG_MEDIA_SUPPORT=y
CONFIG_MEDIA_CAMERA_SUPPORT=y
CONFIG_V4L_PLATFORM_DRIVERS=y
@@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
CONFIG_SND_ATMEL_SOC_WM8904=y
# CONFIG_HID_GENERIC is not set
CONFIG_SND_ATMEL_SOC_PDMIC=y
+CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
CONFIG_USB=y
CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
CONFIG_USB_EHCI_HCD=y
@@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
CONFIG_IIO=y
CONFIG_AT91_ADC=y
CONFIG_AT91_SAMA5D2_ADC=y
+CONFIG_ENVELOPE_DETECTOR=y
+CONFIG_DPOT_DAC=y
+CONFIG_MCP4531=y
CONFIG_PWM=y
CONFIG_PWM_ATMEL=y
CONFIG_PWM_ATMEL_HLCDC_PWM=y
--
2.1.4
^ permalink raw reply related
* [PATCH v2 0/2] phy: Replace the deprecated extcon API
From: Chanwoo Choi @ 2017-01-10 8:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483071089-8362-1-git-send-email-cw00.choi@samsung.com>
Hi Kishon,
Could you review these patches or pick up them if there is no any comment?
On 2016? 12? 30? 13:11, Chanwoo Choi wrote:
> This patches just replace the deprecated extcon API without any change
> of extcon operation and use the resource-managed function for
> extcon_register_notifier().
>
> The new extcon API instead of deprecated API.
> - extcon_set_cable_state_() -> extcon_set_state_sync();
> - extcon_get_cable_state_() -> extcon_get_state();
>
> Changes from v1:
> - Rebase these patches based on v4.10-rc1.
> - Drop the usb/power-supply/chipidea patches.
>
> Chanwoo Choi (2):
> phy: rcar-gen3-usb2: Replace the deprecated extcon API
> phy: sun4i-usb: Replace the deprecated extcon API
>
> drivers/phy/phy-rcar-gen3-usb2.c | 8 ++++----
> drivers/phy/phy-sun4i-usb.c | 4 ++--
> 2 files changed, 6 insertions(+), 6 deletions(-)
>
--
Best Regards,
Chanwoo Choi
S/W Center, Samsung Electronics
^ permalink raw reply
* [PATCH v2] usb: musb: sunxi: Uses the resource-managed extcon API when registering extcon notifier
From: Chanwoo Choi @ 2017-01-10 8:20 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483071550-8683-1-git-send-email-cw00.choi@samsung.com>
Hi Felipe,
This patch got the acked-by from Bin Liu and.
Could you please apply this patch?
On 2016? 12? 30? 13:19, Chanwoo Choi wrote:
> This patch just uses the resource-managed extcon API when registering
> the extcon notifier.
>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
> Acked-by: Bin Liu <b-liu@ti.com>
> ---
> Changes from v1:
> - Rebase this patch based on v4.10-rc1.
> - Add acked-by tag from Maxime Ripard and Bin Lin.
> - Drop the phy/power-supply/chipidea patches.
>
> drivers/usb/musb/sunxi.c | 12 +++---------
> 1 file changed, 3 insertions(+), 9 deletions(-)
>
> diff --git a/drivers/usb/musb/sunxi.c b/drivers/usb/musb/sunxi.c
> index d0be0eadd0d9..2332294dee0f 100644
> --- a/drivers/usb/musb/sunxi.c
> +++ b/drivers/usb/musb/sunxi.c
> @@ -251,14 +251,14 @@ static int sunxi_musb_init(struct musb *musb)
> writeb(SUNXI_MUSB_VEND0_PIO_MODE, musb->mregs + SUNXI_MUSB_VEND0);
>
> /* Register notifier before calling phy_init() */
> - ret = extcon_register_notifier(glue->extcon, EXTCON_USB_HOST,
> - &glue->host_nb);
> + ret = devm_extcon_register_notifier(glue->dev, glue->extcon,
> + EXTCON_USB_HOST, &glue->host_nb);
> if (ret)
> goto error_reset_assert;
>
> ret = phy_init(glue->phy);
> if (ret)
> - goto error_unregister_notifier;
> + goto error_reset_assert;
>
> musb->isr = sunxi_musb_interrupt;
>
> @@ -267,9 +267,6 @@ static int sunxi_musb_init(struct musb *musb)
>
> return 0;
>
> -error_unregister_notifier:
> - extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
> - &glue->host_nb);
> error_reset_assert:
> if (test_bit(SUNXI_MUSB_FL_HAS_RESET, &glue->flags))
> reset_control_assert(glue->rst);
> @@ -293,9 +290,6 @@ static int sunxi_musb_exit(struct musb *musb)
>
> phy_exit(glue->phy);
>
> - extcon_unregister_notifier(glue->extcon, EXTCON_USB_HOST,
> - &glue->host_nb);
> -
> if (test_bit(SUNXI_MUSB_FL_HAS_RESET, &glue->flags))
> reset_control_assert(glue->rst);
>
>
--
Best Regards,
Chanwoo Choi
S/W Center, Samsung Electronics
^ permalink raw reply
* [RFC PATCH 1/5] regulator: Extend the power-management APIs
From: Boris Brezillon @ 2017-01-10 8:33 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170109191758.7zzxeh45pvwiw3jo@sirena.org.uk>
Hi Mark,
On Mon, 9 Jan 2017 19:17:58 +0000
Mark Brown <broonie@kernel.org> wrote:
> On Fri, Dec 02, 2016 at 02:57:12PM +0100, Boris Brezillon wrote:
>
> > The idea to solve #2 is to allow runtime changes. Since this kind of
> > change is likely to have an impact on the whole system, we require the
> > board to explicitly state that runtime changes are allowed (using a DT
> > property).
>
> > Allowing runtime changes, may also be a problem if devices are not
> > suspended in the correct order: a device using a regulator should be
> > suspended before the regulator itself, otherwise we may change the
> > regulator state while it's still being used.
> > Hopefully, this problem will be solved with the work done on device
> > dependency description.
>
> I'm not sure that adding an extra property is going to help with the
> problems here - the system already has to provide explicit support for
> setting the suspend configuration so that should be enough.
I'm not a big fan of this DT property either, but after our discussion
on IRC I had the feeling you wanted it to be as safe as possible, and
since changing the regulator config at runtime is far more dangerous
than asking the regulator to enter a specific state after everything has
been suspended, I thought you would prefer to have an extra property
stating that entering suspend state at runtime is authorized (meaning
it's safe to do it).
> However it
> *is* a bit more than just making sure that the device suspend ordering
> is good (though that's definitely part of it), there will be things
> kicked off by hardware signalling without software knowing about it.
Do you have an example, so that I can understand the use case?
>
> Anything that doesn't affect a hardware supported runtime state probably
> needs to be split off and handled separately as that's the much more
> risky bit
Just to be sure, you mean regulator devices that do not support the
->set_suspend_xx() hooks, right?
>, moving changing of suspend mode earlier isn't going to cause
> too much grief, that patch should just be split out and can probably
> just go straight in.
Yes, I just thought it would be clearer to have everything implemented
in the same function. Since calling ->set_suspend_xx() does not have
any impact on the runtime state, it can be called whenever we want
(assuming we can still communicate with the regulator device to
configure this suspend state).
But if you prefer to have it split out in 2 different function, with the
'set suspend mode' bits called from the regulator_suspend_begin(), I'm
fine with that.
>
> > + * This function should be called from the regulator driver ->suspend() hook
> > + * and after the platform has called regulator_suspend_begin() to properly set
> > + * the rdev->suspend.target field.
>
> Requring these functions to be called from every single driver seems
> like we're doing something wrong - if we're going to do this we should
> find some way to loop over all regulators and apply any unapplied
> changes.
I agree. Actually, I forgot that we had PM ops at the device class
level. Maybe we could just move these generic ->suspend()/->resume()
implementation here.
> Batching things up at the end of suspend would also mean that
> we'd be able to minimise the chances that we get the ordering wrong.
Unfortunately that's not possible, for the exact same reason calling
regulator_suspend_prepare() from the platform ->prepare() hook did not
work for me: at that point, all devices have been suspended, and this
includes the i2c controller which we're using to communicate with the
PMIC exposing those regulators.
This leaves 2 solutions:
1/ Apply the suspend state earlier (before the devices ->suspend()
hooks have been called)
2/ Rely on the device model dependency graph, and enter the suspend
state when the regulator device is being suspended (this is the
solution I'm proposing in this patch).
Solution #1 is acceptable if we omit the case where one regulator
consumer (another device) is depending on the regulator to be setup
properly until the device has been suspended. But this still leaves the
'apply suspend state as late as possible' problem, and in this regards,
solution #1 is clearly not the best option.
Solution #2 might not be perfect right now, but it should benefit from
all the work done by Rafael on 'device dependency tracking' and
'suspend/resume ordering'.
>
> For the target bit... we should be able to find some way to figure out
> what kind of suspend we're doing without the platform being involved, a
> callback from the PM core would be helpful here.
Yep, I agree. Rafael, what's your opinion?
Thanks for your comments.
Boris
^ permalink raw reply
* [PATCH v5 3/3] dmaengine: xilinx_dma: Fix race condition in the driver for multiple descriptor scenario
From: Vinod Koul @ 2017-01-10 8:49 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483771530-8545-4-git-send-email-appanad@xilinx.com>
On Sat, Jan 07, 2017 at 12:15:30PM +0530, Kedareswara rao Appana wrote:
> When driver is handling AXI DMA SoftIP
> When user submits multiple descriptors back to back on the S2MM(recv)
> side with the current driver flow the last buffer descriptor next bd
> points to a invalid location resulting the invalid data or errors in the
> DMA engine.
Can you rephrase this, it a bit hard to understand.
>
> This patch fixes this issue by creating a BD Chain during
whats a BD?
> channel allocation itself and use those BD's.
>
> Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
> ---
> Changes for v5:
> ---> None.
> Changes for v4:
> ---> None.
> Changes for v3:
> ---> None.
> Changes for v2:
> ---> None.
>
> drivers/dma/xilinx/xilinx_dma.c | 133 +++++++++++++++++++++++++---------------
> 1 file changed, 83 insertions(+), 50 deletions(-)
>
> diff --git a/drivers/dma/xilinx/xilinx_dma.c b/drivers/dma/xilinx/xilinx_dma.c
> index 0e9c02e..af2159d 100644
> --- a/drivers/dma/xilinx/xilinx_dma.c
> +++ b/drivers/dma/xilinx/xilinx_dma.c
> @@ -163,6 +163,7 @@
> #define XILINX_DMA_BD_SOP BIT(27)
> #define XILINX_DMA_BD_EOP BIT(26)
> #define XILINX_DMA_COALESCE_MAX 255
> +#define XILINX_DMA_NUM_DESCS 255
why 255?
> #define XILINX_DMA_NUM_APP_WORDS 5
>
> /* Multi-Channel DMA Descriptor offsets*/
> @@ -310,6 +311,7 @@ struct xilinx_dma_tx_descriptor {
> * @pending_list: Descriptors waiting
> * @active_list: Descriptors ready to submit
> * @done_list: Complete descriptors
> + * @free_seg_list: Free descriptors
> * @common: DMA common channel
> * @desc_pool: Descriptors pool
> * @dev: The dma device
> @@ -331,7 +333,9 @@ struct xilinx_dma_tx_descriptor {
> * @desc_submitcount: Descriptor h/w submitted count
> * @residue: Residue for AXI DMA
> * @seg_v: Statically allocated segments base
> + * @seg_p: Physical allocated segments base
> * @cyclic_seg_v: Statically allocated segment base for cyclic transfers
> + * @cyclic_seg_p: Physical allocated segments base for cyclic dma
> * @start_transfer: Differentiate b/w DMA IP's transfer
> */
> struct xilinx_dma_chan {
> @@ -342,6 +346,7 @@ struct xilinx_dma_chan {
> struct list_head pending_list;
> struct list_head active_list;
> struct list_head done_list;
> + struct list_head free_seg_list;
> struct dma_chan common;
> struct dma_pool *desc_pool;
> struct device *dev;
> @@ -363,7 +368,9 @@ struct xilinx_dma_chan {
> u32 desc_submitcount;
> u32 residue;
> struct xilinx_axidma_tx_segment *seg_v;
> + dma_addr_t seg_p;
> struct xilinx_axidma_tx_segment *cyclic_seg_v;
> + dma_addr_t cyclic_seg_p;
> void (*start_transfer)(struct xilinx_dma_chan *chan);
> u16 tdest;
> };
> @@ -569,17 +576,31 @@ static struct xilinx_axidma_tx_segment *
> xilinx_axidma_alloc_tx_segment(struct xilinx_dma_chan *chan)
> {
> struct xilinx_axidma_tx_segment *segment;
> - dma_addr_t phys;
> -
> - segment = dma_pool_zalloc(chan->desc_pool, GFP_ATOMIC, &phys);
> - if (!segment)
> - return NULL;
> + unsigned long flags;
>
> - segment->phys = phys;
> + spin_lock_irqsave(&chan->lock, flags);
> + if (!list_empty(&chan->free_seg_list)) {
> + segment = list_first_entry(&chan->free_seg_list,
> + struct xilinx_axidma_tx_segment,
> + node);
> + list_del(&segment->node);
> + }
> + spin_unlock_irqrestore(&chan->lock, flags);
>
> return segment;
> }
>
> +static void xilinx_dma_clean_hw_desc(struct xilinx_axidma_desc_hw *hw)
> +{
> + u32 next_desc = hw->next_desc;
> + u32 next_desc_msb = hw->next_desc_msb;
> +
> + memset(hw, 0, sizeof(struct xilinx_axidma_desc_hw));
> +
> + hw->next_desc = next_desc;
> + hw->next_desc_msb = next_desc_msb;
> +}
> +
> /**
> * xilinx_dma_free_tx_segment - Free transaction segment
> * @chan: Driver specific DMA channel
> @@ -588,7 +609,9 @@ xilinx_axidma_alloc_tx_segment(struct xilinx_dma_chan *chan)
> static void xilinx_dma_free_tx_segment(struct xilinx_dma_chan *chan,
> struct xilinx_axidma_tx_segment *segment)
> {
> - dma_pool_free(chan->desc_pool, segment, segment->phys);
> + xilinx_dma_clean_hw_desc(&segment->hw);
> +
> + list_add_tail(&segment->node, &chan->free_seg_list);
> }
>
> /**
> @@ -713,16 +736,26 @@ static void xilinx_dma_free_descriptors(struct xilinx_dma_chan *chan)
> static void xilinx_dma_free_chan_resources(struct dma_chan *dchan)
> {
> struct xilinx_dma_chan *chan = to_xilinx_chan(dchan);
> + unsigned long flags;
>
> dev_dbg(chan->dev, "Free all channel resources.\n");
>
> xilinx_dma_free_descriptors(chan);
> +
> if (chan->xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
> - xilinx_dma_free_tx_segment(chan, chan->cyclic_seg_v);
> - xilinx_dma_free_tx_segment(chan, chan->seg_v);
> + spin_lock_irqsave(&chan->lock, flags);
> + INIT_LIST_HEAD(&chan->free_seg_list);
> + spin_unlock_irqrestore(&chan->lock, flags);
> +
> + /* Free Memory that is allocated for cyclic DMA Mode */
> + dma_free_coherent(chan->dev, sizeof(*chan->cyclic_seg_v),
> + chan->cyclic_seg_v, chan->cyclic_seg_p);
> + }
> +
> + if (chan->xdev->dma_config->dmatype != XDMA_TYPE_AXIDMA) {
> + dma_pool_destroy(chan->desc_pool);
> + chan->desc_pool = NULL;
> }
> - dma_pool_destroy(chan->desc_pool);
> - chan->desc_pool = NULL;
> }
>
> /**
> @@ -805,6 +838,7 @@ static void xilinx_dma_do_tasklet(unsigned long data)
> static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
> {
> struct xilinx_dma_chan *chan = to_xilinx_chan(dchan);
> + int i;
>
> /* Has this channel already been allocated? */
> if (chan->desc_pool)
> @@ -815,11 +849,30 @@ static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
> * for meeting Xilinx VDMA specification requirement.
> */
> if (chan->xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
> - chan->desc_pool = dma_pool_create("xilinx_dma_desc_pool",
> - chan->dev,
> - sizeof(struct xilinx_axidma_tx_segment),
> - __alignof__(struct xilinx_axidma_tx_segment),
> - 0);
> + /* Allocate the buffer descriptors. */
> + chan->seg_v = dma_zalloc_coherent(chan->dev,
> + sizeof(*chan->seg_v) *
> + XILINX_DMA_NUM_DESCS,
> + &chan->seg_p, GFP_KERNEL);
> + if (!chan->seg_v) {
> + dev_err(chan->dev,
> + "unable to allocate channel %d descriptors\n",
> + chan->id);
> + return -ENOMEM;
> + }
> +
> + for (i = 0; i < XILINX_DMA_NUM_DESCS; i++) {
> + chan->seg_v[i].hw.next_desc =
> + lower_32_bits(chan->seg_p + sizeof(*chan->seg_v) *
> + ((i + 1) % XILINX_DMA_NUM_DESCS));
> + chan->seg_v[i].hw.next_desc_msb =
> + upper_32_bits(chan->seg_p + sizeof(*chan->seg_v) *
> + ((i + 1) % XILINX_DMA_NUM_DESCS));
> + chan->seg_v[i].phys = chan->seg_p +
> + sizeof(*chan->seg_v) * i;
> + list_add_tail(&chan->seg_v[i].node,
> + &chan->free_seg_list);
> + }
> } else if (chan->xdev->dma_config->dmatype == XDMA_TYPE_CDMA) {
> chan->desc_pool = dma_pool_create("xilinx_cdma_desc_pool",
> chan->dev,
> @@ -834,7 +887,8 @@ static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
> 0);
> }
>
> - if (!chan->desc_pool) {
> + if (!chan->desc_pool &&
> + (chan->xdev->dma_config->dmatype != XDMA_TYPE_AXIDMA)) {
> dev_err(chan->dev,
> "unable to allocate channel %d descriptor pool\n",
> chan->id);
> @@ -843,22 +897,20 @@ static int xilinx_dma_alloc_chan_resources(struct dma_chan *dchan)
>
> if (chan->xdev->dma_config->dmatype == XDMA_TYPE_AXIDMA) {
> /*
> - * For AXI DMA case after submitting a pending_list, keep
> - * an extra segment allocated so that the "next descriptor"
> - * pointer on the tail descriptor always points to a
> - * valid descriptor, even when paused after reaching taildesc.
> - * This way, it is possible to issue additional
> - * transfers without halting and restarting the channel.
> - */
> - chan->seg_v = xilinx_axidma_alloc_tx_segment(chan);
> -
> - /*
> * For cyclic DMA mode we need to program the tail Descriptor
> * register with a value which is not a part of the BD chain
> * so allocating a desc segment during channel allocation for
> * programming tail descriptor.
> */
> - chan->cyclic_seg_v = xilinx_axidma_alloc_tx_segment(chan);
> + chan->cyclic_seg_v = dma_zalloc_coherent(chan->dev,
> + sizeof(*chan->cyclic_seg_v),
> + &chan->cyclic_seg_p, GFP_KERNEL);
> + if (!chan->cyclic_seg_v) {
> + dev_err(chan->dev,
> + "unable to allocate desc segment for cyclic DMA\n");
> + return -ENOMEM;
> + }
> + chan->cyclic_seg_v->phys = chan->cyclic_seg_p;
> }
>
> dma_cookie_init(dchan);
> @@ -1198,7 +1250,7 @@ static void xilinx_cdma_start_transfer(struct xilinx_dma_chan *chan)
> static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
> {
> struct xilinx_dma_tx_descriptor *head_desc, *tail_desc;
> - struct xilinx_axidma_tx_segment *tail_segment, *old_head, *new_head;
> + struct xilinx_axidma_tx_segment *tail_segment;
> u32 reg;
>
> if (chan->err)
> @@ -1217,21 +1269,6 @@ static void xilinx_dma_start_transfer(struct xilinx_dma_chan *chan)
> tail_segment = list_last_entry(&tail_desc->segments,
> struct xilinx_axidma_tx_segment, node);
>
> - if (chan->has_sg && !chan->xdev->mcdma) {
> - old_head = list_first_entry(&head_desc->segments,
> - struct xilinx_axidma_tx_segment, node);
> - new_head = chan->seg_v;
> - /* Copy Buffer Descriptor fields. */
> - new_head->hw = old_head->hw;
> -
> - /* Swap and save new reserve */
> - list_replace_init(&old_head->node, &new_head->node);
> - chan->seg_v = old_head;
> -
> - tail_segment->hw.next_desc = chan->seg_v->phys;
> - head_desc->async_tx.phys = new_head->phys;
> - }
> -
> reg = dma_ctrl_read(chan, XILINX_DMA_REG_DMACR);
>
> if (chan->desc_pendingcount <= XILINX_DMA_COALESCE_MAX) {
> @@ -1729,7 +1766,7 @@ static struct dma_async_tx_descriptor *xilinx_dma_prep_slave_sg(
> {
> struct xilinx_dma_chan *chan = to_xilinx_chan(dchan);
> struct xilinx_dma_tx_descriptor *desc;
> - struct xilinx_axidma_tx_segment *segment = NULL, *prev = NULL;
> + struct xilinx_axidma_tx_segment *segment = NULL;
> u32 *app_w = (u32 *)context;
> struct scatterlist *sg;
> size_t copy;
> @@ -1780,10 +1817,6 @@ static struct dma_async_tx_descriptor *xilinx_dma_prep_slave_sg(
> XILINX_DMA_NUM_APP_WORDS);
> }
>
> - if (prev)
> - prev->hw.next_desc = segment->phys;
> -
> - prev = segment;
> sg_used += copy;
>
> /*
> @@ -1797,7 +1830,6 @@ static struct dma_async_tx_descriptor *xilinx_dma_prep_slave_sg(
> segment = list_first_entry(&desc->segments,
> struct xilinx_axidma_tx_segment, node);
> desc->async_tx.phys = segment->phys;
> - prev->hw.next_desc = segment->phys;
>
> /* For the last DMA_MEM_TO_DEV transfer, set EOP */
> if (chan->direction == DMA_MEM_TO_DEV) {
> @@ -2341,6 +2373,7 @@ static int xilinx_dma_chan_probe(struct xilinx_dma_device *xdev,
> INIT_LIST_HEAD(&chan->pending_list);
> INIT_LIST_HEAD(&chan->done_list);
> INIT_LIST_HEAD(&chan->active_list);
> + INIT_LIST_HEAD(&chan->free_seg_list);
>
> /* Retrieve the channel properties from the device tree */
> has_dre = of_property_read_bool(node, "xlnx,include-dre");
> --
> 2.1.2
>
--
~Vinod
^ permalink raw reply
* [QUESTION] Arm64: Query L3 cache info via DT
From: Tan Xiaojun @ 2017-01-10 8:50 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <81784854-11f8-468a-a280-69be0a714a3b@arm.com>
I add this patch, and test in Hisilicon D02/D03. It can work well.
I'm sorry to reply so late. I took some time to debug, because I am not familiar with the code.
> + if (level < of_level) {
> + /*
> + * some external caches not specified in CLIDR_EL1
> + * the information may be available in the device tree
> + * only unified external caches are considered here
> + */
> + level = of_level;
> + leaves += (of_level - level);
The above two lines need to exchange the location.
> + }
PS: I will test the other scenes, the next step.
Thanks.
Xiaojun.
----------------------------------------------------------------------------
D02:
root at genericarmv8:~# cat /sys/devices/system/cpu/cpu0/cache/index3/size
16384K
root at genericarmv8:~# cat /sys/devices/system/cpu/cpu0/cache/index3/number_of_sets
4096
root at genericarmv8:~# cat /sys/devices/system/cpu/cpu0/cache/index3/coherency_line_size
64
root at genericarmv8:~# cat /sys/devices/system/cpu/cpu0/cache/index3/level
3
root at genericarmv8:~# cat /sys/devices/system/cpu/cpu0/cache/index3/shared_cpu_list
0-15
root at genericarmv8:~# cat /sys/devices/system/cpu/cpu0/cache/index3/shared_cpu_map
ffff
----------------------------------------------------------------------------
D02 (some data may be not accurate):
diff --git a/arch/arm64/boot/dts/hisilicon/hip05.dtsi b/arch/arm64/boot/dts/hisilicon/hip05.dtsi
index 4b472a3..aac18c2 100644
--- a/arch/arm64/boot/dts/hisilicon/hip05.dtsi
+++ b/arch/arm64/boot/dts/hisilicon/hip05.dtsi
@@ -215,18 +215,30 @@
cluster0_l2: l2-cache0 {
compatible = "cache";
+ next-level-cache = <&die0_l3c>;
};
cluster1_l2: l2-cache1 {
compatible = "cache";
+ next-level-cache = <&die0_l3c>;
};
cluster2_l2: l2-cache2 {
compatible = "cache";
+ next-level-cache = <&die0_l3c>;
};
cluster3_l2: l2-cache3 {
compatible = "cache";
+ next-level-cache = <&die0_l3c>;
+ };
+
+ die0_l3c: l3-cache {
+ compatible = "cache";
+ cache-size = <16777216>;
+ cache-line-size = <64>;
+ cache-block-size = <16>;
+ cache-sets = <4096>;
};
};
On 2017/1/4 19:47, Sudeep Holla wrote:
>
> Hi Tan,
>
> On 28/12/16 03:42, Tan Xiaojun wrote:
>> Hi.
>>
>> I saw you discussed how to achieve querying cache information and
>> tend to implement the external ones(like L3 cache) via DT a few
>> months ago.
>>
>> http://lists.infradead.org/pipermail/linux-arm-kernel/2016-February/405399.html
>>
>> Are these implementations progressing? Forgive me to take the
>> liberty to ask, we care about this thing.
>>
>
> Yes the support to override the cache properties for DT was added in v4.10
>
> However, it still depends on the the sysreg to get the total levels of
> caches supported in the system. You may need to tweak a bit around that
> to support what you need.
>
>> If you've already implemented some codes, we can help with testing
>> (in Hisilicon D02, D03, D05) after you send it to the mail-list.
>>
>
> Sure, that would help.
>
>> We can try our best to help if there is any difficulty.
>
> OK, you can start trying the patch below :). It's not even compile
> tested, so you make have to make some changes necessary. I just wanted
> to put my thoughts here. Make sure all the L3 cacheinfo is present in DT.
>
> Regards,
> Sudeep
>
>
> --
>
> diff --git i/arch/arm64/kernel/cacheinfo.c w/arch/arm64/kernel/cacheinfo.c
> index 9617301f76b5..88fbcd368104 100644
> --- i/arch/arm64/kernel/cacheinfo.c
> +++ w/arch/arm64/kernel/cacheinfo.c
> @@ -84,7 +84,7 @@ static void ci_leaf_init(struct cacheinfo *this_leaf,
>
> static int __init_cache_level(unsigned int cpu)
> {
> - unsigned int ctype, level, leaves;
> + unsigned int ctype, level, leaves, of_level;
> struct cpu_cacheinfo *this_cpu_ci = get_cpu_cacheinfo(cpu);
>
> for (level = 1, leaves = 0; level <= MAX_CACHE_LEVEL; level++) {
> @@ -97,6 +97,17 @@ static int __init_cache_level(unsigned int cpu)
> leaves += (ctype == CACHE_TYPE_SEPARATE) ? 2 : 1;
> }
>
> + of_level = of_count_cache_levels(cpu);
> + if (level < of_level) {
> + /*
> + * some external caches not specified in CLIDR_EL1
> + * the information may be available in the device tree
> + * only unified external caches are considered here
> + */
> + level = of_level;
> + leaves += (of_level - level);
> + }
> +
> this_cpu_ci->num_levels = level;
> this_cpu_ci->num_leaves = leaves;
> return 0;
> diff --git i/drivers/of/base.c w/drivers/of/base.c
> index d4bea3c797d6..8007f3b06cb8 100644
> --- i/drivers/of/base.c
> +++ w/drivers/of/base.c
> @@ -2267,6 +2267,20 @@ struct device_node *of_find_next_cache_node(const
> struct device_node *np)
> return NULL;
> }
>
> +int of_count_cache_levels(unsigned int cpu)
> +{
> + int level = 0;
> + struct device *cpu_dev = get_cpu_device(cpu);
> + struct device_node *np = cpu_dev->of_node;
> +
> + while (np) {
> + level++;
> + np = of_find_next_cache_node(np);
> + }
> +
> + return level;
> +}
> +
> /**
> * of_graph_parse_endpoint() - parse common endpoint node properties
> * @node: pointer to endpoint device_node
> diff --git i/include/linux/of.h w/include/linux/of.h
> index d72f01009297..c8597ae71ff3 100644
> --- i/include/linux/of.h
> +++ w/include/linux/of.h
> @@ -280,6 +280,7 @@ extern struct device_node
> *of_get_child_by_name(const struct device_node *node,
>
> /* cache lookup */
> extern struct device_node *of_find_next_cache_node(const struct
> device_node *);
> +extern int of_count_cache_levels(unsigned int cpu);
> extern struct device_node *of_find_node_with_property(
> struct device_node *from, const char *prop_name);
>
>
> .
>
^ permalink raw reply related
* [PATCH 2/3 v2] iio: adc: break out common code from SPMI VADC
From: Linus Walleij @ 2017-01-10 8:54 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <717ea1c4-33af-f0ca-e018-5d7ac87506e1@kernel.org>
On Fri, Dec 30, 2016 at 8:01 PM, Jonathan Cameron <jic23@kernel.org> wrote:
> On 15/12/16 22:48, Linus Walleij wrote:
>> The SPMI VADC and the earlier XOADC share a subset of
>> common code, so to be able to use the same code in both
>> drivers, we break out a separate file with the common code,
>> prefix exported functions that are no longer static with
>> qcom_* and bake an object qcom-vadc.o that contains both
>> files: qcom-vadc-common.o and qcom-spmi-vadc.o.
>>
>> Cc: linux-arm-kernel at lists.infradead.org
>> Cc: linux-arm-msm at vger.kernel.org
>> Cc: Ivan T. Ivanov <iivanov.xz@gmail.com>
>> Cc: Andy Gross <andy.gross@linaro.org>
>> Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
>> Cc: Stephen Boyd <sboyd@codeaurora.org>
>> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
>> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
>
> Looks superficially fine, but I'm guessing will need a respin
> as we have a fair bit of new stuff (and a couple of fixes) going
> through this driver at the moment.
>
> All but the two fixes I posted a few mins ago are in my testing
> branch and should go to Greg once I have confirmed testing on
> those two fixes.
I looked at the git and "testing"
contains a top commit named "guessing" fixing some 64bit
artithmetic (which looks correct) in the driver, shall I simply
rebase on top of that and hope for the best? :)
Yours,
Linus Walleij
^ permalink raw reply
* [PATCH v7 5/8] IIO: add bindings for STM32 timer trigger driver
From: Benjamin Gaignard @ 2017-01-10 8:55 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170109180448.f3pcpuarhcddo76b@rob-hp-laptop>
2017-01-09 19:04 GMT+01:00 Rob Herring <robh@kernel.org>:
> On Thu, Jan 05, 2017 at 10:25:41AM +0100, Benjamin Gaignard wrote:
>> Define bindings for STM32 timer trigger
>>
>> version 4:
>> - remove triggers enumeration from DT
>> - add reg parameter
>>
>> version 3:
>> - change file name
>> - add cross reference with mfd bindings
>>
>> version 2:
>> - only keep one compatible
>> - add DT parameters to set lists of the triggers:
>> one list describe the triggers created by the device
>> another one give the triggers accepted by the device
>>
>> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
>> ---
>> .../bindings/iio/timer/stm32-timer-trigger.txt | 23 ++++++++++++++++++++++
>> 1 file changed, 23 insertions(+)
>> create mode 100644 Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt
>>
>> diff --git a/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt
>> new file mode 100644
>> index 0000000..36a6c4a
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/iio/timer/stm32-timer-trigger.txt
>> @@ -0,0 +1,23 @@
>> +STMicroelectronics STM32 Timers IIO timer bindings
>> +
>> +Must be a sub-node of an STM32 Timers device tree node.
>> +See ../mfd/stm32-timers.txt for details about the parent node.
>> +
>> +Required parameters:
>> +- compatible: Must be "st,stm32-timer-trigger".
>> +- reg: Define triggers configuration of the hardware IP.
>
> Valid values? Not sure this makes sense for use of reg. reg should be
> how you address or id a device.
I use reg like an id to distinguish device and get the right
configuration inside
the driver.
>
>> +
>> +Example:
>> + timers at 40010000 {
>> + #address-cells = <1>;
>> + #size-cells = <0>;
>> + compatible = "st,stm32-timers";
>> + reg = <0x40010000 0x400>;
>> + clocks = <&rcc 0 160>;
>> + clock-names = "clk_int";
>> +
>> + timer {
>
> This would also need an unit address.
Ok I will fix that
>
>> + compatible = "st,stm32-timer-trigger";
>> + reg = <0>;
>> + };
>> + };
>> --
>> 1.9.1
>>
--
Benjamin Gaignard
Graphic Study Group
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply
* [PATCH v7 2/8] MFD: add STM32 Timers driver
From: Benjamin Gaignard @ 2017-01-10 8:56 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170109180051.uwd4su3maj5gkf5l@rob-hp-laptop>
2017-01-09 19:00 GMT+01:00 Rob Herring <robh@kernel.org>:
> On Thu, Jan 05, 2017 at 10:25:38AM +0100, Benjamin Gaignard wrote:
>> This hardware block could at used at same time for PWM generation
>> and IIO timers.
>> PWM and IIO timer configuration are mixed in the same registers
>> so we need a multi fonction driver to be able to share those registers.
>>
>> version 7:
>> - rebase on v4.10-rc2
>>
>> version 6:
>> - rename files to stm32-timers
>> - rename functions to stm32_timers_xxx
>>
>> version 5:
>> - fix Lee comments about detect function
>> - add missing dependency on REGMAP_MMIO
>>
>> version 4:
>> - add a function to detect Auto Reload Register (ARR) size
>> - rename the structure shared with other drivers
>>
>> version 2:
>> - rename driver "stm32-gptimer" to be align with SoC documentation
>> - only keep one compatible
>> - use of_platform_populate() instead of devm_mfd_add_devices()
>>
>> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@st.com>
>> ---
>> .../devicetree/bindings/mfd/stm32-timers.txt | 2 +-
>> drivers/mfd/Kconfig | 11 +++
>> drivers/mfd/Makefile | 2 +
>> drivers/mfd/stm32-timers.c | 80 ++++++++++++++++++++++
>> include/linux/mfd/stm32-timers.h | 71 +++++++++++++++++++
>> 5 files changed, 165 insertions(+), 1 deletion(-)
>> create mode 100644 drivers/mfd/stm32-timers.c
>> create mode 100644 include/linux/mfd/stm32-timers.h
>>
>> diff --git a/Documentation/devicetree/bindings/mfd/stm32-timers.txt b/Documentation/devicetree/bindings/mfd/stm32-timers.txt
>> index a73301d..897e7c2 100644
>> --- a/Documentation/devicetree/bindings/mfd/stm32-timers.txt
>> +++ b/Documentation/devicetree/bindings/mfd/stm32-timers.txt
>> @@ -12,7 +12,7 @@ Required parameters:
>>
>> - reg: Physical base address and length of the controller's
>> registers.
>> -- clock-names: Set to "int".
>> +- clock-names: Set to "int".
>
> This hunk should be dropped or moved to previous patch.
I will move it in the previous patch
>
>> - clocks: Phandle to the clock used by the timer module.
>> For Clk properties, please refer to ../clock/clock-bindings.txt
>>
--
Benjamin Gaignard
Graphic Study Group
Linaro.org ? Open source software for ARM SoCs
Follow Linaro: Facebook | Twitter | Blog
^ permalink raw reply
* [GIT PULL] Renesas ARM64 Based SoC DT Updates for v4.11
From: Geert Uytterhoeven @ 2017-01-10 9:09 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20170110075403.GA25239@verge.net.au>
On Tue, Jan 10, 2017 at 8:54 AM, Simon Horman <horms@verge.net.au> wrote:
> On Mon, Jan 09, 2017 at 07:15:32PM -0800, Olof Johansson wrote:
>> On Fri, Jan 06, 2017 at 12:17:56PM +0100, Simon Horman wrote:
>> > ----------------------------------------------------------------
>> > Chris Paterson (3):
>> > arm64: dts: r8a7796: Add CAN external clock support
>> > arm64: dts: r8a7796: Add CAN support
>> > arm64: dts: r8a7796: Add CAN FD support
>> >
>> > Geert Uytterhoeven (2):
>> > arm64: dts: r8a7796: Add all MSIOF nodes
>> > arm64: renesas: r8a7796/salvator-x: Add board part number to DT bindings
>>
>> Nit: When you look at the shortlog, these with different/random format
>> stand out. Feel free to fix them before sending next time.
>
> Sure, sorry for letting that slip through.
Note that the last one stands out because it's not a DTS update, but a DT
binding update, and thus follows a different convention ;-)
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* [PATCH v5 2/2] ARM: sama5_defconfig: add support for the Axentia TSE-850 board
From: Nicolas Ferre @ 2017-01-10 9:10 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1484035732-31635-3-git-send-email-peda@axentia.se>
Le 10/01/2017 ? 09:08, Peter Rosin a ?crit :
> Signed-off-by: Peter Rosin <peda@axentia.se>
I know that most of the entries in this configuration file are direct
additions to the kernel but what about moving some of your additions to
modules?
Regards,
> ---
> arch/arm/configs/sama5_defconfig | 7 ++++++-
> 1 file changed, 6 insertions(+), 1 deletion(-)
>
> diff --git a/arch/arm/configs/sama5_defconfig b/arch/arm/configs/sama5_defconfig
> index aca8625b6fc9..bf5b3a73e38c 100644
> --- a/arch/arm/configs/sama5_defconfig
> +++ b/arch/arm/configs/sama5_defconfig
> @@ -131,7 +131,7 @@ CONFIG_GPIO_SYSFS=y
> CONFIG_POWER_SUPPLY=y
> CONFIG_BATTERY_ACT8945A=y
> CONFIG_POWER_RESET=y
> -# CONFIG_HWMON is not set
> +CONFIG_SENSORS_JC42=y
> CONFIG_WATCHDOG=y
> CONFIG_AT91SAM9X_WATCHDOG=y
> CONFIG_SAMA5D4_WATCHDOG=y
> @@ -142,6 +142,7 @@ CONFIG_REGULATOR=y
> CONFIG_REGULATOR_FIXED_VOLTAGE=y
> CONFIG_REGULATOR_ACT8865=y
> CONFIG_REGULATOR_ACT8945A=y
> +CONFIG_REGULATOR_PWM=y
> CONFIG_MEDIA_SUPPORT=y
> CONFIG_MEDIA_CAMERA_SUPPORT=y
> CONFIG_V4L_PLATFORM_DRIVERS=y
> @@ -164,6 +165,7 @@ CONFIG_SND_ATMEL_SOC=y
> CONFIG_SND_ATMEL_SOC_WM8904=y
> # CONFIG_HID_GENERIC is not set
> CONFIG_SND_ATMEL_SOC_PDMIC=y
> +CONFIG_SND_ATMEL_SOC_TSE850_PCM5142=y
> CONFIG_USB=y
> CONFIG_USB_ANNOUNCE_NEW_DEVICES=y
> CONFIG_USB_EHCI_HCD=y
> @@ -199,6 +201,9 @@ CONFIG_AT_XDMAC=y
> CONFIG_IIO=y
> CONFIG_AT91_ADC=y
> CONFIG_AT91_SAMA5D2_ADC=y
> +CONFIG_ENVELOPE_DETECTOR=y
> +CONFIG_DPOT_DAC=y
> +CONFIG_MCP4531=y
> CONFIG_PWM=y
> CONFIG_PWM_ATMEL=y
> CONFIG_PWM_ATMEL_HLCDC_PWM=y
>
--
Nicolas Ferre
^ permalink raw reply
* [PATCH v2 0/2] media: rc: add support for IR receiver on MT7623 SoC
From: sean.wang at mediatek.com @ 2017-01-10 9:13 UTC (permalink / raw)
To: linux-arm-kernel
From: Sean Wang <sean.wang@mediatek.com>
This patchset introduces consumer IR (CIR) support on MT7623 SoC
that also works on other similar SoCs and implements raw mode for
more compatibility with different protocols. The driver simply
reports the duration of pulses and spaces to rc-core logic to
decode.
Changes since v1:
- change compatible string from "mediatek,mt7623-ir" into
"mediatek,mt7623-cir"
- use KBUILD_MODNAME to provide consistent device name used in driver.
- remove unused fields in struct mtk_ir.
- use synchronize_irq to give protection between IRQ handler and
remove handler.
- use devm_rc_allocate_device based on Andi Shyti's work.
- simplify error handling patch with devm_rc_register_device and devm_rc_allocate_device.
- remove unused spinlock.
- add comments about hardware limitation and related workarounds.
- enhance the caculation of sampling period for easiler assigned specific
value.
- refine git description.
- fix IR message handling between IR hardware and rc-core.
Sean Wang (2):
Documentation: devicetree: Add document bindings for mtk-cir
media: rc: add driver for IR remote receiver on MT7623 SoC
.../devicetree/bindings/media/mtk-cir.txt | 24 ++
drivers/media/rc/Kconfig | 11 +
drivers/media/rc/Makefile | 1 +
drivers/media/rc/mtk-cir.c | 326 +++++++++++++++++++++
4 files changed, 362 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/mtk-cir.txt
create mode 100644 drivers/media/rc/mtk-cir.c
--
2.7.4
^ permalink raw reply
* [PATCH v2 1/2] Documentation: devicetree: Add document bindings for mtk-cir
From: sean.wang at mediatek.com @ 2017-01-10 9:13 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1484039631-25120-1-git-send-email-sean.wang@mediatek.com>
From: Sean Wang <sean.wang@mediatek.com>
This patch adds documentation for devicetree bindings for
Mediatek consumer IR controller.
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
---
.../devicetree/bindings/media/mtk-cir.txt | 24 ++++++++++++++++++++++
1 file changed, 24 insertions(+)
create mode 100644 Documentation/devicetree/bindings/media/mtk-cir.txt
diff --git a/Documentation/devicetree/bindings/media/mtk-cir.txt b/Documentation/devicetree/bindings/media/mtk-cir.txt
new file mode 100644
index 0000000..3850cbd
--- /dev/null
+++ b/Documentation/devicetree/bindings/media/mtk-cir.txt
@@ -0,0 +1,24 @@
+Device-Tree bindings for Mediatek consumer IR controller found in
+Mediatek SoC family
+
+Required properties:
+- compatible : "mediatek,mt7623-cir"
+- clocks : list of clock specifiers, corresponding to
+ entries in clock-names property;
+- clock-names : should contain "clk" entries;
+- interrupts : should contain IR IRQ number;
+- reg : should contain IO map address for IR.
+
+Optional properties:
+- linux,rc-map-name : Remote control map name.
+
+Example:
+
+cir: cir at 10013000 {
+ compatible = "mediatek,mt7623-cir";
+ reg = <0 0x10013000 0 0x1000>;
+ interrupts = <GIC_SPI 87 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_IRRX>;
+ clock-names = "clk";
+ linux,rc-map-name = "rc-rc6-mce";
+};
--
2.7.4
^ permalink raw reply related
* [PATCH v2 2/2] media: rc: add driver for IR remote receiver on MT7623 SoC
From: sean.wang at mediatek.com @ 2017-01-10 9:13 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1484039631-25120-1-git-send-email-sean.wang@mediatek.com>
From: Sean Wang <sean.wang@mediatek.com>
This patch adds driver for IR controller on MT7623 SoC.
and should also work on similar Mediatek SoC. Currently
testing successfully on NEC and SONY remote controller
only but it should work on others (lirc, rc-5 and rc-6).
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Reviewed-by: Sean Young <sean@mess.org>
---
drivers/media/rc/Kconfig | 11 ++
drivers/media/rc/Makefile | 1 +
drivers/media/rc/mtk-cir.c | 326 +++++++++++++++++++++++++++++++++++++++++++++
3 files changed, 338 insertions(+)
create mode 100644 drivers/media/rc/mtk-cir.c
diff --git a/drivers/media/rc/Kconfig b/drivers/media/rc/Kconfig
index 629e8ca..9228479 100644
--- a/drivers/media/rc/Kconfig
+++ b/drivers/media/rc/Kconfig
@@ -235,6 +235,17 @@ config IR_MESON
To compile this driver as a module, choose M here: the
module will be called meson-ir.
+config IR_MTK
+ tristate "Mediatek IR remote receiver"
+ depends on RC_CORE
+ depends on ARCH_MEDIATEK || COMPILE_TEST
+ ---help---
+ Say Y if you want to use the IR remote receiver available
+ on Mediatek SoCs.
+
+ To compile this driver as a module, choose M here: the
+ module will be called mtk-cir.
+
config IR_NUVOTON
tristate "Nuvoton w836x7hg Consumer Infrared Transceiver"
depends on PNP
diff --git a/drivers/media/rc/Makefile b/drivers/media/rc/Makefile
index 3a984ee..a78570b 100644
--- a/drivers/media/rc/Makefile
+++ b/drivers/media/rc/Makefile
@@ -38,3 +38,4 @@ obj-$(CONFIG_RC_ST) += st_rc.o
obj-$(CONFIG_IR_SUNXI) += sunxi-cir.o
obj-$(CONFIG_IR_IMG) += img-ir/
obj-$(CONFIG_IR_SERIAL) += serial_ir.o
+obj-$(CONFIG_IR_MTK) += mtk-cir.o
diff --git a/drivers/media/rc/mtk-cir.c b/drivers/media/rc/mtk-cir.c
new file mode 100644
index 0000000..f752f63
--- /dev/null
+++ b/drivers/media/rc/mtk-cir.c
@@ -0,0 +1,326 @@
+/*
+ * Driver for Mediatek IR Receiver Controller
+ *
+ * Copyright (C) 2017 Sean Wang <sean.wang@mediatek.com>
+ *
+ * This program is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of
+ * the License, or (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/interrupt.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/reset.h>
+#include <media/rc-core.h>
+
+#define MTK_IR_DEV KBUILD_MODNAME
+
+/* Register to enable PWM and IR */
+#define MTK_CONFIG_HIGH_REG 0x0c
+/* Enable IR pulse width detection */
+#define MTK_PWM_EN BIT(13)
+/* Enable IR hardware function */
+#define MTK_IR_EN BIT(0)
+
+/* Register to setting sample period */
+#define MTK_CONFIG_LOW_REG 0x10
+/* Field to set sample period */
+#define CHK_PERIOD DIV_ROUND_CLOSEST(MTK_IR_SAMPLE, \
+ MTK_IR_CLK_PERIOD)
+#define MTK_CHK_PERIOD (((CHK_PERIOD) << 8) & (GENMASK(20, 8)))
+#define MTK_CHK_PERIOD_MASK (GENMASK(20, 8))
+
+/* Register to clear state of state machine */
+#define MTK_IRCLR_REG 0x20
+/* Bit to restart IR receiving */
+#define MTK_IRCLR BIT(0)
+
+/* Register containing pulse width data */
+#define MTK_CHKDATA_REG(i) (0x88 + 4 * (i))
+#define MTK_WIDTH_MASK (GENMASK(7, 0))
+
+/* Register to enable IR interrupt */
+#define MTK_IRINT_EN_REG 0xcc
+/* Bit to enable interrupt */
+#define MTK_IRINT_EN BIT(0)
+
+/* Register to ack IR interrupt */
+#define MTK_IRINT_CLR_REG 0xd0
+/* Bit to clear interrupt status */
+#define MTK_IRINT_CLR BIT(0)
+
+/* Maximum count of samples */
+#define MTK_MAX_SAMPLES 0xff
+/* Indicate the end of IR message */
+#define MTK_IR_END(v, p) ((v) == MTK_MAX_SAMPLES && (p) == 0)
+/* Number of registers to record the pulse width */
+#define MTK_CHKDATA_SZ 17
+/* Source clock frequency */
+#define MTK_IR_BASE_CLK 273000000
+/* Frequency after IR internal divider */
+#define MTK_IR_CLK_FREQ (MTK_IR_BASE_CLK / 4)
+/* Period for MTK_IR_CLK in ns*/
+#define MTK_IR_CLK_PERIOD DIV_ROUND_CLOSEST(1000000000ul, \
+ MTK_IR_CLK_FREQ)
+/* Sample period in ns */
+#define MTK_IR_SAMPLE (MTK_IR_CLK_PERIOD * 0xc00)
+
+/* struct mtk_ir - This is the main datasructure for holding the state
+ * of the driver
+ * @dev: The device pointer
+ * @rc: The rc instrance
+ * @irq: The IRQ that we are using
+ * @base: The mapped register i/o base
+ * @clk: The clock that we are using
+ */
+struct mtk_ir {
+ struct device *dev;
+ struct rc_dev *rc;
+ void __iomem *base;
+ int irq;
+ struct clk *clk;
+};
+
+static void mtk_w32_mask(struct mtk_ir *ir, u32 val, u32 mask, unsigned int reg)
+{
+ u32 tmp;
+
+ tmp = __raw_readl(ir->base + reg);
+ tmp = (tmp & ~mask) | val;
+ __raw_writel(tmp, ir->base + reg);
+}
+
+static void mtk_w32(struct mtk_ir *ir, u32 val, unsigned int reg)
+{
+ __raw_writel(val, ir->base + reg);
+}
+
+static u32 mtk_r32(struct mtk_ir *ir, unsigned int reg)
+{
+ return __raw_readl(ir->base + reg);
+}
+
+static inline void mtk_irq_disable(struct mtk_ir *ir, u32 mask)
+{
+ u32 val;
+
+ val = mtk_r32(ir, MTK_IRINT_EN_REG);
+ mtk_w32(ir, val & ~mask, MTK_IRINT_EN_REG);
+}
+
+static inline void mtk_irq_enable(struct mtk_ir *ir, u32 mask)
+{
+ u32 val;
+
+ val = mtk_r32(ir, MTK_IRINT_EN_REG);
+ mtk_w32(ir, val | mask, MTK_IRINT_EN_REG);
+}
+
+static irqreturn_t mtk_ir_irq(int irqno, void *dev_id)
+{
+ struct mtk_ir *ir = dev_id;
+ u8 wid = 0;
+ u32 i, j, val;
+ DEFINE_IR_RAW_EVENT(rawir);
+
+ mtk_irq_disable(ir, MTK_IRINT_EN);
+
+ /* Reset decoder state machine */
+ ir_raw_event_reset(ir->rc);
+
+ /* First message must be pulse */
+ rawir.pulse = false;
+
+ /* Handle all pulse and space IR controller captures */
+ for (i = 0 ; i < MTK_CHKDATA_SZ ; i++) {
+ val = mtk_r32(ir, MTK_CHKDATA_REG(i));
+ dev_dbg(ir->dev, "@reg%d=0x%08x\n", i, val);
+
+ for (j = 0 ; j < 4 ; j++) {
+ wid = (val & (MTK_WIDTH_MASK << j * 8)) >> j * 8;
+ rawir.pulse = !rawir.pulse;
+ rawir.duration = wid * (MTK_IR_SAMPLE + 1);
+ ir_raw_event_store_with_filter(ir->rc, &rawir);
+ }
+ }
+
+ /* The maximum number of edges the IR controller can
+ * hold is MTK_CHKDATA_SZ * 4. So if received IR messages
+ * is over the limit, the last incomplete IR message would
+ * be appended trailing space and still would be sent into
+ * ir-rc-raw to decode. That helps it is possible that it
+ * has enough information to decode a scancode even if the
+ * trailing end of the message is missing.
+ */
+ if (!MTK_IR_END(wid, rawir.pulse)) {
+ rawir.pulse = false;
+ rawir.duration = MTK_MAX_SAMPLES * (MTK_IR_SAMPLE + 1);
+ ir_raw_event_store_with_filter(ir->rc, &rawir);
+ }
+
+ ir_raw_event_handle(ir->rc);
+
+ /* Restart controller for the next receive */
+ mtk_w32_mask(ir, 0x1, MTK_IRCLR, MTK_IRCLR_REG);
+
+ /* Clear interrupt status */
+ mtk_w32_mask(ir, 0x1, MTK_IRINT_CLR, MTK_IRINT_CLR_REG);
+
+ /* Enable interrupt */
+ mtk_irq_enable(ir, MTK_IRINT_EN);
+
+ return IRQ_HANDLED;
+}
+
+static int mtk_ir_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *dn = dev->of_node;
+ struct resource *res;
+ struct mtk_ir *ir;
+ u32 val;
+ int ret = 0;
+ const char *map_name;
+
+ ir = devm_kzalloc(dev, sizeof(struct mtk_ir), GFP_KERNEL);
+ if (!ir)
+ return -ENOMEM;
+
+ ir->dev = dev;
+
+ if (!of_device_is_compatible(dn, "mediatek,mt7623-cir"))
+ return -ENODEV;
+
+ ir->clk = devm_clk_get(dev, "clk");
+ if (IS_ERR(ir->clk)) {
+ dev_err(dev, "failed to get a ir clock.\n");
+ return PTR_ERR(ir->clk);
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ ir->base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(ir->base)) {
+ dev_err(dev, "failed to map registers\n");
+ return PTR_ERR(ir->base);
+ }
+
+ ir->rc = devm_rc_allocate_device(dev, RC_DRIVER_IR_RAW);
+ if (!ir->rc) {
+ dev_err(dev, "failed to allocate device\n");
+ return -ENOMEM;
+ }
+
+ ir->rc->priv = ir;
+ ir->rc->input_name = MTK_IR_DEV;
+ ir->rc->input_phys = MTK_IR_DEV "/input0";
+ ir->rc->input_id.bustype = BUS_HOST;
+ ir->rc->input_id.vendor = 0x0001;
+ ir->rc->input_id.product = 0x0001;
+ ir->rc->input_id.version = 0x0001;
+ map_name = of_get_property(dn, "linux,rc-map-name", NULL);
+ ir->rc->map_name = map_name ?: RC_MAP_EMPTY;
+ ir->rc->dev.parent = dev;
+ ir->rc->driver_name = MTK_IR_DEV;
+ ir->rc->allowed_protocols = RC_BIT_ALL;
+ ir->rc->rx_resolution = MTK_IR_SAMPLE;
+ ir->rc->timeout = MTK_MAX_SAMPLES * (MTK_IR_SAMPLE + 1);
+
+ ret = devm_rc_register_device(dev, ir->rc);
+ if (ret) {
+ dev_err(dev, "failed to register rc device\n");
+ return ret;
+ }
+
+ platform_set_drvdata(pdev, ir);
+
+ ir->irq = platform_get_irq(pdev, 0);
+ if (ir->irq < 0) {
+ dev_err(dev, "no irq resource\n");
+ return -ENODEV;
+ }
+
+ /* Enable interrupt after proper hardware
+ * setup and IRQ handler registration
+ */
+ if (clk_prepare_enable(ir->clk)) {
+ dev_err(dev, "try to enable ir_clk failed\n");
+ ret = -EINVAL;
+ goto exit_clkdisable_clk;
+ }
+
+ mtk_irq_disable(ir, MTK_IRINT_EN);
+
+ ret = devm_request_irq(dev, ir->irq, mtk_ir_irq, 0, MTK_IR_DEV, ir);
+ if (ret) {
+ dev_err(dev, "failed request irq\n");
+ goto exit_clkdisable_clk;
+ }
+
+ /* Enable IR and PWM */
+ val = mtk_r32(ir, MTK_CONFIG_HIGH_REG);
+ val |= MTK_PWM_EN | MTK_IR_EN;
+ mtk_w32(ir, val, MTK_CONFIG_HIGH_REG);
+
+ /* Setting sample period */
+ mtk_w32_mask(ir, MTK_CHK_PERIOD, MTK_CHK_PERIOD_MASK,
+ MTK_CONFIG_LOW_REG);
+
+ mtk_irq_enable(ir, MTK_IRINT_EN);
+
+ dev_info(dev, "Initialized MT7623 IR driver, sample period = %luus\n",
+ DIV_ROUND_CLOSEST(MTK_IR_SAMPLE, 1000));
+
+ return 0;
+
+exit_clkdisable_clk:
+ clk_disable_unprepare(ir->clk);
+
+ return ret;
+}
+
+static int mtk_ir_remove(struct platform_device *pdev)
+{
+ struct mtk_ir *ir = platform_get_drvdata(pdev);
+
+ /* Avoid contention between remove handler and
+ * IRQ handler so that disabling IR interrupt and
+ * waiting for pending IRQ handler to complete
+ */
+ mtk_irq_disable(ir, MTK_IRINT_EN);
+ synchronize_irq(ir->irq);
+
+ clk_disable_unprepare(ir->clk);
+
+ rc_unregister_device(ir->rc);
+
+ return 0;
+}
+
+static const struct of_device_id mtk_ir_match[] = {
+ { .compatible = "mediatek,mt7623-cir" },
+ {},
+};
+MODULE_DEVICE_TABLE(of, mtk_ir_match);
+
+static struct platform_driver mtk_ir_driver = {
+ .probe = mtk_ir_probe,
+ .remove = mtk_ir_remove,
+ .driver = {
+ .name = MTK_IR_DEV,
+ .of_match_table = mtk_ir_match,
+ },
+};
+
+module_platform_driver(mtk_ir_driver);
+
+MODULE_DESCRIPTION("Mediatek IR Receiver Controller Driver");
+MODULE_AUTHOR("Sean Wang <sean.wang@mediatek.com>");
+MODULE_LICENSE("GPL");
--
2.7.4
^ permalink raw reply related
* [PATCH 1/3] arm64: dts: Pine64: add MMC support
From: kbuild test robot @ 2017-01-10 9:24 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1484011353-21480-2-git-send-email-andre.przywara@arm.com>
Hi Andre,
[auto build test ERROR on mripard/sunxi/for-next]
[also build test ERROR on next-20170110]
[cannot apply to robh/for-next v4.10-rc3]
[if your patch is applied to the wrong git tree, please drop us a note to help improve the system]
url: https://github.com/0day-ci/linux/commits/Andre-Przywara/arm64-dts-A64-board-MMC-support/20170110-124554
base: https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux.git sunxi/for-next
config: arm64-defconfig (attached as .config)
compiler: aarch64-linux-gnu-gcc (Debian 6.1.1-9) 6.1.1 20160705
reproduce:
wget https://git.kernel.org/cgit/linux/kernel/git/wfg/lkp-tests.git/plain/sbin/make.cross -O ~/bin/make.cross
chmod +x ~/bin/make.cross
# save the attached .config to linux build tree
make.cross ARCH=arm64
All errors (new ones prefixed by >>):
>> Error: arch/arm64/boot/dts/allwinner/sun50i-a64-pine64.dts:83.1-6 Label or path mmc0 not found
>> FATAL ERROR: Syntax error parsing input tree
---
0-DAY kernel test infrastructure Open Source Technology Center
https://lists.01.org/pipermail/kbuild-all Intel Corporation
-------------- next part --------------
A non-text attachment was scrubbed...
Name: .config.gz
Type: application/gzip
Size: 33694 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20170110/b272af74/attachment-0001.gz>
^ permalink raw reply
* [PATCH v8 0/5] Add support for the STM32F4 I2C
From: Linus Walleij @ 2017-01-10 9:26 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483607246-14771-1-git-send-email-cedric.madianga@gmail.com>
On Thu, Jan 5, 2017 at 10:07 AM, M'boumba Cedric Madianga
<cedric.madianga@gmail.com> wrote:
> This patchset adds support for the I2C controller embedded in STM32F4xx SoC.
> It enables I2C transfer in interrupt mode with Standard-mode and Fast-mode bus
> speed.
The whole series:
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Looks perfect from my point of view now.
Yours,
Linus Walleij
^ permalink raw reply
* [RESEND 3/3] ARM: davinci_all_defconfig: enable iio and ADS7950
From: Sekhar Nori @ 2017-01-10 9:27 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1483978300-403-4-git-send-email-david@lechnology.com>
On Monday 09 January 2017 09:41 PM, David Lechner wrote:
> This enables the iio subsystem and the TI ADS7950 driver. This is used by
> LEGO MINDSTORMS EV3, which has an ADS7957 chip.
>
> Signed-off-by: David Lechner <david@lechnology.com>
> ---
> arch/arm/configs/davinci_all_defconfig | 7 +++++++
> 1 file changed, 7 insertions(+)
>
> diff --git a/arch/arm/configs/davinci_all_defconfig b/arch/arm/configs/davinci_all_defconfig
> index 2b1967a..a899876 100644
> --- a/arch/arm/configs/davinci_all_defconfig
> +++ b/arch/arm/configs/davinci_all_defconfig
> @@ -200,6 +200,13 @@ CONFIG_TI_EDMA=y
> CONFIG_MEMORY=y
> CONFIG_TI_AEMIF=m
> CONFIG_DA8XX_DDRCTL=y
> +CONFIG_IIO=m
> +CONFIG_IIO_BUFFER_CB=m
> +CONFIG_IIO_SW_DEVICE=m
> +CONFIG_IIO_SW_TRIGGER=m
> +CONFIG_TI_ADS7950=m
> +CONFIG_IIO_HRTIMER_TRIGGER=m
> +CONFIG_IIO_SYSFS_TRIGGER=m
Hmm, there are some other comments I gave on the previous version I
don't see addressed. Can you please fix those or respond to those comments?
Thanks,
Sekhar
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox