* [PATCH v3 09/11] thermal: armada: Wait sensors validity before exiting the init callback
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
The thermal core will check for sensors validity right after the
initialization callback has returned. As the initialization routine make
a reset, the sensors are not ready immediately and the core spawns an
error in the dmesg. Avoid this annoying situation by polling on the
validity bit before exiting from these routines. This also avoid the use
of blind sleeps.
Suggested-by: David Sniatkiwicz <davidsn@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 23 ++++++++++++++++++++---
1 file changed, 20 insertions(+), 3 deletions(-)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index be141ca53e83..1c4122f7377c 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -23,6 +23,7 @@
#include <linux/platform_device.h>
#include <linux/of_device.h>
#include <linux/thermal.h>
+#include <linux/iopoll.h>
/* Thermal Manager Control and Status Register */
#define PMU_TDC0_SW_RST_MASK (0x1 << 1)
@@ -59,6 +60,9 @@
#define CONTROL1_EXT_TSEN_SW_RESET BIT(7)
#define CONTROL1_EXT_TSEN_HW_RESETn BIT(8)
+#define STATUS_POLL_PERIOD_US 1000
+#define STATUS_POLL_TIMEOUT_US 100000
+
struct armada_thermal_data;
/* Marvell EBU Thermal Sensor Dev Structure */
@@ -154,6 +158,16 @@ static void armada375_init_sensor(struct platform_device *pdev,
msleep(50);
}
+static void armada_wait_sensor_validity(struct armada_thermal_priv *priv)
+{
+ u32 reg;
+
+ readl_relaxed_poll_timeout(priv->status, reg,
+ reg & priv->data->is_valid_bit,
+ STATUS_POLL_PERIOD_US,
+ STATUS_POLL_TIMEOUT_US);
+}
+
static void armada380_init_sensor(struct platform_device *pdev,
struct armada_thermal_priv *priv)
{
@@ -163,7 +177,6 @@ static void armada380_init_sensor(struct platform_device *pdev,
reg |= CONTROL1_EXT_TSEN_HW_RESETn;
reg &= ~CONTROL1_EXT_TSEN_SW_RESET;
writel(reg, priv->control1);
- msleep(10);
/* Set Tsen Tc Trim to correct default value (errata #132698) */
if (priv->control0) {
@@ -171,8 +184,10 @@ static void armada380_init_sensor(struct platform_device *pdev,
reg &= ~CONTROL0_TSEN_TC_TRIM_MASK;
reg |= CONTROL0_TSEN_TC_TRIM_VAL;
writel(reg, priv->control0);
- msleep(10);
}
+
+ /* Wait the sensors to be valid or the core will warn the user */
+ armada_wait_sensor_validity(priv);
}
static void armada_ap806_init_sensor(struct platform_device *pdev,
@@ -190,7 +205,9 @@ static void armada_ap806_init_sensor(struct platform_device *pdev,
reg &= ~CONTROL0_TSEN_RESET;
reg |= CONTROL0_TSEN_START | CONTROL0_TSEN_ENABLE;
writel(reg, priv->control0);
- msleep(10);
+
+ /* Wait the sensors to be valid or the core will warn the user */
+ armada_wait_sensor_validity(priv);
}
static bool armada_is_valid(struct armada_thermal_priv *priv)
--
2.11.0
^ permalink raw reply related
* [PATCH v3 08/11] thermal: armada: Change sensors trim default value
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
Errata #132698 highlights an error in the default value of Tc trim.
Set this parameter to b'011.
Suggested-by: David Sniatkiwicz <davidsn@marvell.com>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index da58a8961a37..be141ca53e83 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -46,6 +46,10 @@
#define CONTROL0_OFFSET 0x0
#define CONTROL1_OFFSET 0x4
+/* Errata fields */
+#define CONTROL0_TSEN_TC_TRIM_MASK 0x7
+#define CONTROL0_TSEN_TC_TRIM_VAL 0x3
+
/* TSEN refers to the temperature sensors within the AP */
#define CONTROL0_TSEN_START BIT(0)
#define CONTROL0_TSEN_RESET BIT(1)
@@ -160,6 +164,15 @@ static void armada380_init_sensor(struct platform_device *pdev,
reg &= ~CONTROL1_EXT_TSEN_SW_RESET;
writel(reg, priv->control1);
msleep(10);
+
+ /* Set Tsen Tc Trim to correct default value (errata #132698) */
+ if (priv->control0) {
+ reg = readl_relaxed(priv->control0);
+ reg &= ~CONTROL0_TSEN_TC_TRIM_MASK;
+ reg |= CONTROL0_TSEN_TC_TRIM_VAL;
+ writel(reg, priv->control0);
+ msleep(10);
+ }
}
static void armada_ap806_init_sensor(struct platform_device *pdev,
--
2.11.0
^ permalink raw reply related
* [PATCH v3 07/11] thermal: armada: Update Kconfig and module description
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
Update Armada thermal driver Kconfig entry as well as the driver's
MODULE_DESCRIPTION content, now that 64-bit SoCs are also supported,
eg. Armada 7K and Armada 8K.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/Kconfig | 4 ++--
drivers/thermal/armada_thermal.c | 2 +-
2 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/drivers/thermal/Kconfig b/drivers/thermal/Kconfig
index 315ae2926e20..44cad046f272 100644
--- a/drivers/thermal/Kconfig
+++ b/drivers/thermal/Kconfig
@@ -301,13 +301,13 @@ config DB8500_THERMAL
thermal zone if trip points reached.
config ARMADA_THERMAL
- tristate "Armada 370/XP thermal management"
+ tristate "Armada 370/XP/7K/8K thermal management"
depends on ARCH_MVEBU || COMPILE_TEST
depends on HAS_IOMEM
depends on OF
help
Enable this option if you want to have support for thermal management
- controller present in Armada 370 and Armada XP SoC.
+ controller present in Armada 370, Armada XP, Armada 7K/8K SoCs.
config DA9062_THERMAL
tristate "DA9062/DA9061 Dialog Semiconductor thermal driver"
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index f5c911524656..da58a8961a37 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -403,5 +403,5 @@ static struct platform_driver armada_thermal_driver = {
module_platform_driver(armada_thermal_driver);
MODULE_AUTHOR("Ezequiel Garcia <ezequiel.garcia@free-electrons.com>");
-MODULE_DESCRIPTION("Armada 370/XP thermal driver");
+MODULE_DESCRIPTION("Armada SoCs thermal driver");
MODULE_LICENSE("GPL v2");
--
2.11.0
^ permalink raw reply related
* [PATCH v3 06/11] thermal: armada: Add support for Armada CP110
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
From: Baruch Siach <baruch@tkos.co.il>
The CP110 component is integrated in the Armada 8k and 7k lines of
processors.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[<miquel.raynal@free-electrons.com>: renamed the register pointers]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 30 ++++++++++++++++++++++++------
1 file changed, 24 insertions(+), 6 deletions(-)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index 279d01937bb8..f5c911524656 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -37,7 +37,6 @@
#define A375_UNIT_CONTROL_MASK 0x7
#define A375_READOUT_INVERT BIT(15)
#define A375_HW_RESETn BIT(8)
-#define A380_HW_RESET BIT(8)
/* Legacy bindings */
#define LEGACY_CONTROL_MEM_LEN 0x4
@@ -52,6 +51,10 @@
#define CONTROL0_TSEN_RESET BIT(1)
#define CONTROL0_TSEN_ENABLE BIT(2)
+/* EXT_TSEN refers to the external temperature sensors, out of the AP */
+#define CONTROL1_EXT_TSEN_SW_RESET BIT(7)
+#define CONTROL1_EXT_TSEN_HW_RESETn BIT(8)
+
struct armada_thermal_data;
/* Marvell EBU Thermal Sensor Dev Structure */
@@ -153,11 +156,10 @@ static void armada380_init_sensor(struct platform_device *pdev,
u32 reg = readl_relaxed(priv->control1);
/* Reset hardware once */
- if (!(reg & A380_HW_RESET)) {
- reg |= A380_HW_RESET;
- writel(reg, priv->control1);
- msleep(10);
- }
+ reg |= CONTROL1_EXT_TSEN_HW_RESETn;
+ reg &= ~CONTROL1_EXT_TSEN_SW_RESET;
+ writel(reg, priv->control1);
+ msleep(10);
}
static void armada_ap806_init_sensor(struct platform_device *pdev,
@@ -280,6 +282,18 @@ static const struct armada_thermal_data armada_ap806_data = {
.signed_sample = true,
};
+static const struct armada_thermal_data armada_cp110_data = {
+ .is_valid = armada_is_valid,
+ .init_sensor = armada380_init_sensor,
+ .is_valid_bit = BIT(10),
+ .temp_shift = 0,
+ .temp_mask = 0x3ff,
+ .coef_b = 1172499100UL,
+ .coef_m = 2000096UL,
+ .coef_div = 4201,
+ .inverted = true,
+};
+
static const struct of_device_id armada_thermal_id_table[] = {
{
.compatible = "marvell,armadaxp-thermal",
@@ -302,6 +316,10 @@ static const struct of_device_id armada_thermal_id_table[] = {
.data = &armada_ap806_data,
},
{
+ .compatible = "marvell,armada-cp110-thermal",
+ .data = &armada_cp110_data,
+ },
+ {
/* sentinel */
},
};
--
2.11.0
^ permalink raw reply related
* [PATCH v3 05/11] thermal: armada: Add support for Armada AP806
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
From: Baruch Siach <baruch@tkos.co.il>
The AP806 component is integrated in the Armada 8k and 7k lines of
processors.
The thermal sensor sample field on the status register is a signed
value. Extend armada_get_temp() to handle signed values.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 51 ++++++++++++++++++++++++++++++++++++++--
1 file changed, 49 insertions(+), 2 deletions(-)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index e5b184cee79b..279d01937bb8 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -47,6 +47,11 @@
#define CONTROL0_OFFSET 0x0
#define CONTROL1_OFFSET 0x4
+/* TSEN refers to the temperature sensors within the AP */
+#define CONTROL0_TSEN_START BIT(0)
+#define CONTROL0_TSEN_RESET BIT(1)
+#define CONTROL0_TSEN_ENABLE BIT(2)
+
struct armada_thermal_data;
/* Marvell EBU Thermal Sensor Dev Structure */
@@ -70,6 +75,7 @@ struct armada_thermal_data {
unsigned long coef_m;
unsigned long coef_div;
bool inverted;
+ bool signed_sample;
/* Register shift and mask to access the sensor temperature */
unsigned int temp_shift;
@@ -154,6 +160,24 @@ static void armada380_init_sensor(struct platform_device *pdev,
}
}
+static void armada_ap806_init_sensor(struct platform_device *pdev,
+ struct armada_thermal_priv *priv)
+{
+ u32 reg;
+
+ if (!priv->control0) {
+ dev_err(&pdev->dev,
+ "Cannot access to control0 (control LSB) register\n");
+ return;
+ }
+
+ reg = readl_relaxed(priv->control0);
+ reg &= ~CONTROL0_TSEN_RESET;
+ reg |= CONTROL0_TSEN_START | CONTROL0_TSEN_ENABLE;
+ writel(reg, priv->control0);
+ msleep(10);
+}
+
static bool armada_is_valid(struct armada_thermal_priv *priv)
{
u32 reg = readl_relaxed(priv->status);
@@ -167,6 +191,7 @@ static int armada_get_temp(struct thermal_zone_device *thermal,
struct armada_thermal_priv *priv = thermal->devdata;
u32 reg;
unsigned long m, b, div;
+ int sample;
/* Valid check */
if (priv->data->is_valid && !priv->data->is_valid(priv)) {
@@ -177,6 +202,11 @@ static int armada_get_temp(struct thermal_zone_device *thermal,
reg = readl_relaxed(priv->status);
reg = (reg >> priv->data->temp_shift) & priv->data->temp_mask;
+ if (priv->data->signed_sample)
+ /* The most significant bit is the sign bit */
+ sample = sign_extend32(reg, fls(priv->data->temp_mask) - 1);
+ else
+ sample = reg;
/* Get formula coeficients */
b = priv->data->coef_b;
@@ -184,9 +214,9 @@ static int armada_get_temp(struct thermal_zone_device *thermal,
div = priv->data->coef_div;
if (priv->data->inverted)
- *temp = ((m * reg) - b) / div;
+ *temp = ((m * sample) - b) / div;
else
- *temp = (b - (m * reg)) / div;
+ *temp = (b - (m * sample)) / div;
return 0;
}
@@ -237,6 +267,19 @@ static const struct armada_thermal_data armada380_data = {
.inverted = true,
};
+static const struct armada_thermal_data armada_ap806_data = {
+ .is_valid = armada_is_valid,
+ .init_sensor = armada_ap806_init_sensor,
+ .is_valid_bit = BIT(16),
+ .temp_shift = 0,
+ .temp_mask = 0x3ff,
+ .coef_b = -150000,
+ .coef_m = 423UL,
+ .coef_div = 1,
+ .inverted = true,
+ .signed_sample = true,
+};
+
static const struct of_device_id armada_thermal_id_table[] = {
{
.compatible = "marvell,armadaxp-thermal",
@@ -255,6 +298,10 @@ static const struct of_device_id armada_thermal_id_table[] = {
.data = &armada380_data,
},
{
+ .compatible = "marvell,armada-ap806-thermal",
+ .data = &armada_ap806_data,
+ },
+ {
/* sentinel */
},
};
--
2.11.0
^ permalink raw reply related
* [PATCH v3 04/11] thermal: armada: Rationalize register accesses
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
Bindings were incomplete for a long time by only exposing one of the two
available control registers. To ease the migration to the full bindings
(already in use for the Armada 375 SoC), rename the pointers for
clarification. This way, it will only be needed to add another pointer
to access the other control register when the time comes.
This avoids dangerous situations where the offset 0 of the control
area can be either one register or the other depending on the bindings
used. After this change, device trees of other SoCs could be migrated to
the "full" bindings if they may benefit from features from the
unaccessible register, without any change in the driver.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 86 +++++++++++++++++++++++++---------------
1 file changed, 55 insertions(+), 31 deletions(-)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index 26698f2d3ca7..e5b184cee79b 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -39,12 +39,21 @@
#define A375_HW_RESETn BIT(8)
#define A380_HW_RESET BIT(8)
+/* Legacy bindings */
+#define LEGACY_CONTROL_MEM_LEN 0x4
+
+/* Current bindings with the 2 control registers under the same memory area */
+#define LEGACY_CONTROL1_OFFSET 0x0
+#define CONTROL0_OFFSET 0x0
+#define CONTROL1_OFFSET 0x4
+
struct armada_thermal_data;
/* Marvell EBU Thermal Sensor Dev Structure */
struct armada_thermal_priv {
- void __iomem *sensor;
- void __iomem *control;
+ void __iomem *status;
+ void __iomem *control0;
+ void __iomem *control1;
struct armada_thermal_data *data;
};
@@ -71,45 +80,45 @@ struct armada_thermal_data {
static void armadaxp_init_sensor(struct platform_device *pdev,
struct armada_thermal_priv *priv)
{
- unsigned long reg;
+ u32 reg;
- reg = readl_relaxed(priv->control);
+ reg = readl_relaxed(priv->control1);
reg |= PMU_TDC0_OTF_CAL_MASK;
- writel(reg, priv->control);
+ writel(reg, priv->control1);
/* Reference calibration value */
reg &= ~PMU_TDC0_REF_CAL_CNT_MASK;
reg |= (0xf1 << PMU_TDC0_REF_CAL_CNT_OFFS);
- writel(reg, priv->control);
+ writel(reg, priv->control1);
/* Reset the sensor */
- reg = readl_relaxed(priv->control);
- writel((reg | PMU_TDC0_SW_RST_MASK), priv->control);
+ reg = readl_relaxed(priv->control1);
+ writel((reg | PMU_TDC0_SW_RST_MASK), priv->control1);
- writel(reg, priv->control);
+ writel(reg, priv->control1);
/* Enable the sensor */
- reg = readl_relaxed(priv->sensor);
+ reg = readl_relaxed(priv->status);
reg &= ~PMU_TM_DISABLE_MASK;
- writel(reg, priv->sensor);
+ writel(reg, priv->status);
}
static void armada370_init_sensor(struct platform_device *pdev,
struct armada_thermal_priv *priv)
{
- unsigned long reg;
+ u32 reg;
- reg = readl_relaxed(priv->control);
+ reg = readl_relaxed(priv->control1);
reg |= PMU_TDC0_OTF_CAL_MASK;
- writel(reg, priv->control);
+ writel(reg, priv->control1);
/* Reference calibration value */
reg &= ~PMU_TDC0_REF_CAL_CNT_MASK;
reg |= (0xf1 << PMU_TDC0_REF_CAL_CNT_OFFS);
- writel(reg, priv->control);
+ writel(reg, priv->control1);
reg &= ~PMU_TDC0_START_CAL_MASK;
- writel(reg, priv->control);
+ writel(reg, priv->control1);
msleep(10);
}
@@ -117,37 +126,37 @@ static void armada370_init_sensor(struct platform_device *pdev,
static void armada375_init_sensor(struct platform_device *pdev,
struct armada_thermal_priv *priv)
{
- unsigned long reg;
+ u32 reg;
- reg = readl(priv->control + 4);
+ reg = readl(priv->control1);
reg &= ~(A375_UNIT_CONTROL_MASK << A375_UNIT_CONTROL_SHIFT);
reg &= ~A375_READOUT_INVERT;
reg &= ~A375_HW_RESETn;
- writel(reg, priv->control + 4);
+ writel(reg, priv->control1);
msleep(20);
reg |= A375_HW_RESETn;
- writel(reg, priv->control + 4);
+ writel(reg, priv->control1);
msleep(50);
}
static void armada380_init_sensor(struct platform_device *pdev,
struct armada_thermal_priv *priv)
{
- unsigned long reg = readl_relaxed(priv->control);
+ u32 reg = readl_relaxed(priv->control1);
/* Reset hardware once */
if (!(reg & A380_HW_RESET)) {
reg |= A380_HW_RESET;
- writel(reg, priv->control);
+ writel(reg, priv->control1);
msleep(10);
}
}
static bool armada_is_valid(struct armada_thermal_priv *priv)
{
- unsigned long reg = readl_relaxed(priv->sensor);
+ u32 reg = readl_relaxed(priv->status);
return reg & priv->data->is_valid_bit;
}
@@ -156,7 +165,7 @@ static int armada_get_temp(struct thermal_zone_device *thermal,
int *temp)
{
struct armada_thermal_priv *priv = thermal->devdata;
- unsigned long reg;
+ u32 reg;
unsigned long m, b, div;
/* Valid check */
@@ -166,7 +175,7 @@ static int armada_get_temp(struct thermal_zone_device *thermal,
return -EIO;
}
- reg = readl_relaxed(priv->sensor);
+ reg = readl_relaxed(priv->status);
reg = (reg >> priv->data->temp_shift) & priv->data->temp_mask;
/* Get formula coeficients */
@@ -253,6 +262,7 @@ MODULE_DEVICE_TABLE(of, armada_thermal_id_table);
static int armada_thermal_probe(struct platform_device *pdev)
{
+ void __iomem *control = NULL;
struct thermal_zone_device *thermal;
const struct of_device_id *match;
struct armada_thermal_priv *priv;
@@ -267,14 +277,28 @@ static int armada_thermal_probe(struct platform_device *pdev)
return -ENOMEM;
res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
- priv->sensor = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(priv->sensor))
- return PTR_ERR(priv->sensor);
+ priv->status = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(priv->status))
+ return PTR_ERR(priv->status);
res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
- priv->control = devm_ioremap_resource(&pdev->dev, res);
- if (IS_ERR(priv->control))
- return PTR_ERR(priv->control);
+ control = devm_ioremap_resource(&pdev->dev, res);
+ if (IS_ERR(control))
+ return PTR_ERR(control);
+
+ /*
+ * Legacy DT bindings only described "control1" register (also referred
+ * as "control MSB" on old documentation). New bindings cover
+ * "control0/control LSB" and "control1/control MSB" registers within
+ * the same resource, which is then of size 8 instead of 4.
+ */
+ if ((res->end - res->start) == LEGACY_CONTROL_MEM_LEN) {
+ /* ->control0 unavailable in this configuration */
+ priv->control1 = control + LEGACY_CONTROL1_OFFSET;
+ } else {
+ priv->control0 = control + CONTROL0_OFFSET;
+ priv->control1 = control + CONTROL1_OFFSET;
+ }
priv->data = (struct armada_thermal_data *)match->data;
priv->data->init_sensor(pdev, priv);
--
2.11.0
^ permalink raw reply related
* [PATCH v3 03/11] thermal: armada: Simplify the check of the validity bit
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
All Armada SoCs use one bit to declare if the sensor values are valid.
This bit moves across the versions of the IP.
The method until then was to do both a shift and compare with an useless
flag of "0x1". It is clearer and quicker to directly save the value that
must be ANDed instead of the bit position and do a single bitwise AND
operation.
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 12 +++++-------
1 file changed, 5 insertions(+), 7 deletions(-)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index 6c4af2622d4f..26698f2d3ca7 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -24,8 +24,6 @@
#include <linux/of_device.h>
#include <linux/thermal.h>
-#define THERMAL_VALID_MASK 0x1
-
/* Thermal Manager Control and Status Register */
#define PMU_TDC0_SW_RST_MASK (0x1 << 1)
#define PMU_TM_DISABLE_OFFS 0
@@ -67,7 +65,7 @@ struct armada_thermal_data {
/* Register shift and mask to access the sensor temperature */
unsigned int temp_shift;
unsigned int temp_mask;
- unsigned int is_valid_shift;
+ unsigned int is_valid_bit;
};
static void armadaxp_init_sensor(struct platform_device *pdev,
@@ -151,7 +149,7 @@ static bool armada_is_valid(struct armada_thermal_priv *priv)
{
unsigned long reg = readl_relaxed(priv->sensor);
- return (reg >> priv->data->is_valid_shift) & THERMAL_VALID_MASK;
+ return reg & priv->data->is_valid_bit;
}
static int armada_get_temp(struct thermal_zone_device *thermal,
@@ -199,7 +197,7 @@ static const struct armada_thermal_data armadaxp_data = {
static const struct armada_thermal_data armada370_data = {
.is_valid = armada_is_valid,
.init_sensor = armada370_init_sensor,
- .is_valid_shift = 9,
+ .is_valid_bit = BIT(9),
.temp_shift = 10,
.temp_mask = 0x1ff,
.coef_b = 3153000000UL,
@@ -210,7 +208,7 @@ static const struct armada_thermal_data armada370_data = {
static const struct armada_thermal_data armada375_data = {
.is_valid = armada_is_valid,
.init_sensor = armada375_init_sensor,
- .is_valid_shift = 10,
+ .is_valid_bit = BIT(10),
.temp_shift = 0,
.temp_mask = 0x1ff,
.coef_b = 3171900000UL,
@@ -221,7 +219,7 @@ static const struct armada_thermal_data armada375_data = {
static const struct armada_thermal_data armada380_data = {
.is_valid = armada_is_valid,
.init_sensor = armada380_init_sensor,
- .is_valid_shift = 10,
+ .is_valid_bit = BIT(10),
.temp_shift = 0,
.temp_mask = 0x3ff,
.coef_b = 1172499100UL,
--
2.11.0
^ permalink raw reply related
* [PATCH v3 02/11] thermal: armada: Use msleep for long delays
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
From: Baruch Siach <baruch@tkos.co.il>
Use msleep for long (> 10ms) delays, instead of the busy waiting mdelay.
All delays are called from the probe routine, where scheduling is
allowed.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
drivers/thermal/armada_thermal.c | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/thermal/armada_thermal.c b/drivers/thermal/armada_thermal.c
index 706d74798cbe..6c4af2622d4f 100644
--- a/drivers/thermal/armada_thermal.c
+++ b/drivers/thermal/armada_thermal.c
@@ -113,7 +113,7 @@ static void armada370_init_sensor(struct platform_device *pdev,
reg &= ~PMU_TDC0_START_CAL_MASK;
writel(reg, priv->control);
- mdelay(10);
+ msleep(10);
}
static void armada375_init_sensor(struct platform_device *pdev,
@@ -127,11 +127,11 @@ static void armada375_init_sensor(struct platform_device *pdev,
reg &= ~A375_HW_RESETn;
writel(reg, priv->control + 4);
- mdelay(20);
+ msleep(20);
reg |= A375_HW_RESETn;
writel(reg, priv->control + 4);
- mdelay(50);
+ msleep(50);
}
static void armada380_init_sensor(struct platform_device *pdev,
@@ -143,7 +143,7 @@ static void armada380_init_sensor(struct platform_device *pdev,
if (!(reg & A380_HW_RESET)) {
reg |= A380_HW_RESET;
writel(reg, priv->control);
- mdelay(10);
+ msleep(10);
}
}
--
2.11.0
^ permalink raw reply related
* [PATCH v3 01/11] dt-bindings: thermal: Describe Armada AP806 and CP110
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214103011.24713-1-miquel.raynal@free-electrons.com>
From: Baruch Siach <baruch@tkos.co.il>
Add compatible strings for AP806 and CP110 that are part of the Armada
8k/7k line of SoCs.
Add a note on the differences in the size of the control area in
different bindings. This is an existing difference between the Armada
375 binding and the other boards already supported. The new AP806 and
CP110 bindings are similar to the existing Armada 375 in this regard.
Also add a note about the new property "marvell,thermal-zone-name" to
help identify the zones from the sysfs.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
[<miquel.raynal@free-electrons.com>: reword, additional details, new
property]
Signed-off-by: Miquel Raynal <miquel.raynal@free-electrons.com>
---
.../devicetree/bindings/thermal/armada-thermal.txt | 29 ++++++++++++++++++----
1 file changed, 24 insertions(+), 5 deletions(-)
diff --git a/Documentation/devicetree/bindings/thermal/armada-thermal.txt b/Documentation/devicetree/bindings/thermal/armada-thermal.txt
index 24aacf8948c5..1602dc2ee220 100644
--- a/Documentation/devicetree/bindings/thermal/armada-thermal.txt
+++ b/Documentation/devicetree/bindings/thermal/armada-thermal.txt
@@ -7,17 +7,36 @@ Required properties:
marvell,armada375-thermal
marvell,armada380-thermal
marvell,armadaxp-thermal
+ marvell,armada-ap806-thermal
+ marvell,armada-cp110-thermal
- reg: Device's register space.
Two entries are expected, see the examples below.
- The first one is required for the sensor register;
- the second one is required for the control register
- to be used for sensor initialization (a.k.a. calibration).
+ The first one points to the status register (4B).
+ The second one points to the control registers (8B).
+ Note: with legacy bindings, the second entry pointed
+ only on the so called "control MSB" ("control 1"), was
+ 4B wide and did not let the possibility to reach the
+ "control LSB" ("control 0") register.
-Example:
+Optional properties:
+- marvell,thermal-zone-name: The name to identify the thermal zone
+ within the sysfs, useful when multiple
+ thermal zones are registered (AP, CPx...).
+
+Examples:
+
+ /* Legacy bindings */
thermal at d0018300 {
compatible = "marvell,armada370-thermal";
- reg = <0xd0018300 0x4
+ reg = <0xd0018300 0x4
0xd0018304 0x4>;
};
+
+ ap_thermal: thermal at 6f8084 {
+ compatible = "marvell,armada-ap806-thermal";
+ reg = <0x6f808C 0x4>,
+ <0x6f8084 0x8>;
+ marvell,thermal-zone-name = "ap_thermal_zone";
+ };
--
2.11.0
^ permalink raw reply related
* [PATCH v3 00/11] Armada thermal: improvements and A7K/A8K SoCs support
From: Miquel Raynal @ 2017-12-14 10:30 UTC (permalink / raw)
To: linux-arm-kernel
Hi,
This series takes over Baruch's series by integrating his patches about
supporting thermal on Armada 7K and 8K SoCs within a larger series with
several improvements on the armada_thermal.c driver.
For now, Armada 380 and CP110 compatibles share the same initialization
routine but this will probably change in the near future when adding
support for overheat interrupts.
DT bindings documentation is updated to match existing code. A new
property is introduced to identify thermal zones, see the commit using
it for more details.
Armada AP806 and CP110 DT are also updated with thermal nodes.
Thank you,
Miqu?l
Baruch Siach (4):
dt-bindings: thermal: Describe Armada AP806 and CP110
thermal: armada: Use msleep for long delays
thermal: armada: Add support for Armada AP806
thermal: armada: Add support for Armada CP110
Miquel Raynal (7):
thermal: armada: Simplify the check of the validity bit
thermal: armada: Rationalize register accesses
thermal: armada: Update Kconfig and module description
thermal: armada: Change sensors trim default value
thermal: armada: Wait sensors validity before exiting the init
callback
thermal: armada: Give useful names to the thermal zone
ARM64: dts: marvell: Add thermal support for A7K/A8K
.../devicetree/bindings/thermal/armada-thermal.txt | 29 ++-
arch/arm64/boot/dts/marvell/armada-ap806.dtsi | 7 +
.../boot/dts/marvell/armada-cp110-master.dtsi | 7 +
.../arm64/boot/dts/marvell/armada-cp110-slave.dtsi | 7 +
drivers/thermal/Kconfig | 4 +-
drivers/thermal/armada_thermal.c | 225 ++++++++++++++++-----
6 files changed, 222 insertions(+), 57 deletions(-)
--
2.11.0
^ permalink raw reply
* [PATCH V6 3/7] device property: Introduce a common API to fetch device match data
From: Sakari Ailus @ 2017-12-14 10:28 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAJZ5v0inHMCLGyPaAeuJNo2VH7f3Th0KdpT2UkPBCsvrSDi0gQ@mail.gmail.com>
On Thu, Dec 07, 2017 at 11:19:51PM +0100, Rafael J. Wysocki wrote:
> On Thu, Dec 7, 2017 at 11:06 PM, Sakari Ailus <sakari.ailus@iki.fi> wrote:
> > On Thu, Dec 07, 2017 at 03:17:52PM -0500, Sinan Kaya wrote:
> >> On 12/7/2017 7:40 AM, Sakari Ailus wrote:
> >> > On Tue, Dec 05, 2017 at 12:04:48PM -0500, Sinan Kaya wrote:
> >> >> @@ -101,6 +103,8 @@ struct fwnode_operations {
> >> >> (*graph_get_port_parent)(struct fwnode_handle *fwnode);
> >> >> int (*graph_parse_endpoint)(const struct fwnode_handle *fwnode,
> >> >> struct fwnode_endpoint *endpoint);
> >> >> + void *(*get_match_data)(const struct fwnode_handle *fwnode,
> >> >> + struct device *dev);
> >> >
> >> > You can make dev const, too.
> >> >
> >>
> >> done, I couldn't change device_get_match_data() parameter const due to
> >> dev_fwnode() function.
> >>
> >> from /local/mnt/workspace/projects/caf/kernel/drivers/base/property.c:13:
> >>
> >> /local/mnt/workspace/projects/caf/kernel/drivers/base/property.c:1341:39: warning: passing argument 1 of 'dev_fwnode' discards 'const' qualifier from pointer target type [-Wdiscarded-qualifiers]
> >> return fwnode_call_ptr_op(dev_fwnode(dev), device_get_match_data,
> >
> > Right. Makes sense.
> >
> > I guess it's not perhaps worth it introducing dev_fwnode_const just for
> > this. devices are seldom if ever const anyway.
>
> They cannot be const. Had they been const, it wouldn't have been
> possible to register them even. :-)
In general no, but this function does not change the device in any way,
therefore it could be const in principle.
--
Sakari Ailus
sakari.ailus at linux.intel.com
^ permalink raw reply
* [PATCH 3/3] ARM: dts: r8a7793: Correct critical CPU temperature
From: Geert Uytterhoeven @ 2017-12-14 10:25 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513242521-11236-4-git-send-email-chris.paterson2@renesas.com>
On Thu, Dec 14, 2017 at 10:08 AM, Chris Paterson
<chris.paterson2@renesas.com> wrote:
> The R-Car M2N hardware manual states that Tc = ?40?C to +105?C. The
M2-N
> thermal sensor has an accuracy of ?5?C and there can be a temperature
> difference of 1 or 2 degrees between Tjmax and the thermal sensor due
> to the location of the latter.
>
> This means that 95?C is a safer value to use.
>
> Fixes: 57f9156bc620ac56 ("ARM: dts: r8a7793: enable to use thermal-zone")
> Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* [PATCH 2/3] ARM: dts: r8a7791: Correct critical CPU temperature
From: Geert Uytterhoeven @ 2017-12-14 10:24 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513242521-11236-3-git-send-email-chris.paterson2@renesas.com>
On Thu, Dec 14, 2017 at 10:08 AM, Chris Paterson
<chris.paterson2@renesas.com> wrote:
> The R-Car M2W hardware manual states that Tc = ?40?C to +105?C. The
M2-W
> thermal sensor has an accuracy of ?5?C and there can be a temperature
> difference of 1 or 2 degrees between Tjmax and the thermal sensor due
> to the location of the latter.
>
> This means that 95?C is a safer value to use.
>
> Fixes: cac68a56e34b9810 ("ARM: dts: r8a7791: enable to use thermal-zone")
> Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* [PATCH 1/3] ARM: dts: r8a7790: Correct critical CPU temperature
From: Geert Uytterhoeven @ 2017-12-14 10:23 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513242521-11236-2-git-send-email-chris.paterson2@renesas.com>
On Thu, Dec 14, 2017 at 10:08 AM, Chris Paterson
<chris.paterson2@renesas.com> wrote:
> The R-Car H2 hardware manual states that Tc = ?40?C to +105?C. The
> thermal sensor has an accuracy of ?5?C and there can be a temperature
> difference of 1 or 2 degrees between Tjmax and the thermal sensor due
> to the location of the latter.
>
> This means that 95?C is a safer value to use.
>
> Fixes: a8b805f3606f7af7 ("ARM: dts: r8a7790: enable to use thermal-zone")
> Signed-off-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert at linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply
* [PATCH 01/10] arm64: add kconfig symbol to configure physical address size
From: Suzuki K Poulose @ 2017-12-14 10:22 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513184845-8711-2-git-send-email-kristina.martsenko@arm.com>
On 13/12/17 17:07, Kristina Martsenko wrote:
> ARMv8.2 introduces support for 52-bit physical addresses. To prepare for
> supporting this, add a new kconfig symbol to configure the physical
> address space size. The symbols will be used in subsequent patches.
> Currently the only choice is 48, a later patch will add the option of 52
> once the required code is in place.
>
> Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
> ---
> arch/arm64/Kconfig | 16 ++++++++++++++++
> 1 file changed, 16 insertions(+)
>
> diff --git a/arch/arm64/Kconfig b/arch/arm64/Kconfig
> index a93339f5178f..8dc937823eeb 100644
> --- a/arch/arm64/Kconfig
> +++ b/arch/arm64/Kconfig
> @@ -646,6 +646,22 @@ config ARM64_VA_BITS
> default 47 if ARM64_VA_BITS_47
> default 48 if ARM64_VA_BITS_48
>
> +choice
> + prompt "Physical address space size"
> + default ARM64_PA_BITS_48
> + help
> + Choose the maximum physical address range that the kernel will
> + support.
> +
> +config ARM64_PA_BITS_48
> + bool "48-bit"
> +
> +endchoice
> +
> +config ARM64_PA_BITS
> + int
> + default 48 if ARM64_PA_BITS_48
> +
> config CPU_BIG_ENDIAN
> bool "Build big-endian kernel"
> help
>
We could replace most of the hard coded "48" PA limit values to ARM64_PA_BITS,
now that we have a configurable entity. i.e, you could fold patch 7 & 8 into
this one.
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
^ permalink raw reply
* [PATCH 07/10] arm64: increase PHYS_MASK to 52 bits
From: Suzuki K Poulose @ 2017-12-14 10:18 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513184845-8711-8-git-send-email-kristina.martsenko@arm.com>
On 13/12/17 17:07, Kristina Martsenko wrote:
> PHYS_MASK_SHIFT represents the highest possible physical address
> supported by the kernel, and is used in a number of places. In order to
> support 52-bit physical memory, increase PHYS_MASK_SHIFT to 52 when
> 52-bit physical memory is configured, and retain 48 if it is not, to
> e.g. keep IDMAP_PGTABLE_LEVELS accurate. (The kconfig option to set
> ARM64_PA_BITS to 52 will be added in a later patch.)
>
> Signed-off-by: Kristina Martsenko <kristina.martsenko@arm.com>
> ---
> arch/arm64/include/asm/pgtable-hwdef.h | 2 +-
> 1 file changed, 1 insertion(+), 1 deletion(-)
>
> diff --git a/arch/arm64/include/asm/pgtable-hwdef.h b/arch/arm64/include/asm/pgtable-hwdef.h
> index 60e0432df559..03fe82057bd1 100644
> --- a/arch/arm64/include/asm/pgtable-hwdef.h
> +++ b/arch/arm64/include/asm/pgtable-hwdef.h
> @@ -206,7 +206,7 @@
> /*
> * Highest possible physical address supported.
> */
> -#define PHYS_MASK_SHIFT (48)
> +#define PHYS_MASK_SHIFT (CONFIG_ARM64_PA_BITS)
> #define PHYS_MASK ((UL(1) << PHYS_MASK_SHIFT) - 1)
>
> /*
>
Kristina,
The changes look good to me. I believe this patch and the next one could be merged
to patch 1 in the series.
Eitherway,
Reviewed-by: Suzuki K Poulose <suzuki.poulose@arm.com>
Cheers
Suzuki
^ permalink raw reply
* [PATCH] mt76: fix memcpy to potential null pointer on failed allocation
From: Felix Fietkau @ 2017-12-14 10:17 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171214101322.10178-1-colin.king@canonical.com>
On 2017-12-14 11:13, Colin King wrote:
> From: Colin Ian King <colin.king@canonical.com>
>
> Currently if the allocation of skb fails and returns NULL then the
> call to skb_put will cause a null pointer dereference. Fix this by
> checking for a null skb and returning NULL. Note that calls to
> function mt76x2_mcu_msg_alloc don't directly check the null return
> but instead pass the NULL pointer to mt76x2_mcu_msg_send which
> checks for the NULL and returns ENOMEM in this case.
>
> Detected by CoverityScan, CID#1462624 ("Dereference null return value")
>
> Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
> Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Felix Fietkau <nbd@nbd.name>
^ permalink raw reply
* [PATCH] mt76: fix memcpy to potential null pointer on failed allocation
From: Colin King @ 2017-12-14 10:13 UTC (permalink / raw)
To: linux-arm-kernel
From: Colin Ian King <colin.king@canonical.com>
Currently if the allocation of skb fails and returns NULL then the
call to skb_put will cause a null pointer dereference. Fix this by
checking for a null skb and returning NULL. Note that calls to
function mt76x2_mcu_msg_alloc don't directly check the null return
but instead pass the NULL pointer to mt76x2_mcu_msg_send which
checks for the NULL and returns ENOMEM in this case.
Detected by CoverityScan, CID#1462624 ("Dereference null return value")
Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
---
drivers/net/wireless/mediatek/mt76/mt76x2_mcu.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/net/wireless/mediatek/mt76/mt76x2_mcu.c b/drivers/net/wireless/mediatek/mt76/mt76x2_mcu.c
index d45737ee1412..15820b11f9db 100644
--- a/drivers/net/wireless/mediatek/mt76/mt76x2_mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt76x2_mcu.c
@@ -45,6 +45,8 @@ static struct sk_buff *mt76x2_mcu_msg_alloc(const void *data, int len)
struct sk_buff *skb;
skb = alloc_skb(len, GFP_KERNEL);
+ if (!skb)
+ return NULL;
memcpy(skb_put(skb, len), data, len);
return skb;
--
2.14.1
^ permalink raw reply related
* [PATCH v7 0/6] add clk controller driver for Meson-AXG SoC
From: Yixun Lan @ 2017-12-14 10:11 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513245826.32163.7.camel@baylibre.com>
Hi Jerome & Kevin
On 12/14/17 18:03, Jerome Brunet wrote:
> On Mon, 2017-12-11 at 22:13 +0800, Yixun Lan wrote:
>> Qiufang Dai (3):
>> clk: meson-axg: add clocks dt-bindings required header
>> clk: meson-axg: add clock controller drivers
>> arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
>>
>> Yixun Lan (3):
>> clk: meson: make the spinlock naming more specific
>> dt-bindings: clock: add compatible variant for the Meson-AXG
>> arm64: dts: meson-axg: switch uart_ao clock to CLK81
>>
>> .../bindings/clock/amlogic,gxbb-clkc.txt | 7 +-
>> arch/arm64/Kconfig.platforms | 1 +
>> arch/arm64/boot/dts/amlogic/meson-axg-s400.dts | 2 +
>> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 19 +-
>> drivers/clk/meson/Kconfig | 8 +
>> drivers/clk/meson/Makefile | 1 +
>> drivers/clk/meson/axg.c | 936 +++++++++++++++++++++
>> drivers/clk/meson/axg.h | 126 +++
>> drivers/clk/meson/clkc.h | 2 +-
>> drivers/clk/meson/gxbb.c | 112 +--
>> drivers/clk/meson/meson8b.c | 24 +-
>> include/dt-bindings/clock/axg-clkc.h | 71 ++
>> 12 files changed, 1234 insertions(+), 75 deletions(-)
>> create mode 100644 drivers/clk/meson/axg.c
>> create mode 100644 drivers/clk/meson/axg.h
>> create mode 100644 include/dt-bindings/clock/axg-clkc.h
>
> Kevin,
>
> I took the first 4 patches through clk-meson. I left the last 2 for you.
>
> I have applied the DT bindings update separately.
> Let me know if you have dependency on these new bindings and need a tag.
>
thanks for taking care of this..
I think it's a good idea to make a tag, if peripheral driver request
clock, then the DT part patch will need
include/dt-bindings/clock/axg-clkc.h to build successfully.
Yixun
^ permalink raw reply
* [PATCH net-next v6 2/2] net: ethernet: socionext: add AVE ethernet driver
From: Kunihiko Hayashi @ 2017-12-14 10:05 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513245910-15961-1-git-send-email-hayashi.kunihiko@socionext.com>
The UniPhier platform from Socionext provides the AVE ethernet
controller that includes MAC and MDIO bus supporting RGMII/RMII
modes. The controller is named AVE.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
---
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/socionext/Kconfig | 22 +
drivers/net/ethernet/socionext/Makefile | 5 +
drivers/net/ethernet/socionext/sni_ave.c | 1727 ++++++++++++++++++++++++++++++
5 files changed, 1756 insertions(+)
create mode 100644 drivers/net/ethernet/socionext/Kconfig
create mode 100644 drivers/net/ethernet/socionext/Makefile
create mode 100644 drivers/net/ethernet/socionext/sni_ave.c
diff --git a/drivers/net/ethernet/Kconfig b/drivers/net/ethernet/Kconfig
index c604213..d50519e 100644
--- a/drivers/net/ethernet/Kconfig
+++ b/drivers/net/ethernet/Kconfig
@@ -170,6 +170,7 @@ source "drivers/net/ethernet/sis/Kconfig"
source "drivers/net/ethernet/sfc/Kconfig"
source "drivers/net/ethernet/sgi/Kconfig"
source "drivers/net/ethernet/smsc/Kconfig"
+source "drivers/net/ethernet/socionext/Kconfig"
source "drivers/net/ethernet/stmicro/Kconfig"
source "drivers/net/ethernet/sun/Kconfig"
source "drivers/net/ethernet/tehuti/Kconfig"
diff --git a/drivers/net/ethernet/Makefile b/drivers/net/ethernet/Makefile
index 39f62733..6cf5ade 100644
--- a/drivers/net/ethernet/Makefile
+++ b/drivers/net/ethernet/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_SFC) += sfc/
obj-$(CONFIG_SFC_FALCON) += sfc/falcon/
obj-$(CONFIG_NET_VENDOR_SGI) += sgi/
obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
+obj-$(CONFIG_NET_VENDOR_SOCIONEXT) += socionext/
obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
obj-$(CONFIG_NET_VENDOR_SUN) += sun/
obj-$(CONFIG_NET_VENDOR_TEHUTI) += tehuti/
diff --git a/drivers/net/ethernet/socionext/Kconfig b/drivers/net/ethernet/socionext/Kconfig
new file mode 100644
index 0000000..3a1829e
--- /dev/null
+++ b/drivers/net/ethernet/socionext/Kconfig
@@ -0,0 +1,22 @@
+config NET_VENDOR_SOCIONEXT
+ bool "Socionext ethernet drivers"
+ default y
+ ---help---
+ Option to select ethernet drivers for Socionext platforms.
+
+ Note that the answer to this question doesn't directly affect the
+ kernel: saying N will just cause the configurator to skip all
+ the questions about Socionext devices. If you say Y, you will be asked
+ for your specific card in the following questions.
+
+if NET_VENDOR_SOCIONEXT
+
+config SNI_AVE
+ tristate "Socionext AVE ethernet support"
+ depends on (ARCH_UNIPHIER || COMPILE_TEST) && OF
+ select PHYLIB
+ ---help---
+ Driver for gigabit ethernet MACs, called AVE, in the
+ Socionext UniPhier family.
+
+endif #NET_VENDOR_SOCIONEXT
diff --git a/drivers/net/ethernet/socionext/Makefile b/drivers/net/ethernet/socionext/Makefile
new file mode 100644
index 0000000..ab83df6
--- /dev/null
+++ b/drivers/net/ethernet/socionext/Makefile
@@ -0,0 +1,5 @@
+# SPDX-License-Identifier: GPL-2.0
+#
+# Makefile for all ethernet ip drivers on Socionext platforms
+#
+obj-$(CONFIG_SNI_AVE) += sni_ave.o
diff --git a/drivers/net/ethernet/socionext/sni_ave.c b/drivers/net/ethernet/socionext/sni_ave.c
new file mode 100644
index 0000000..15f975e
--- /dev/null
+++ b/drivers/net/ethernet/socionext/sni_ave.c
@@ -0,0 +1,1727 @@
+// SPDX-License-Identifier: GPL-2.0
+/**
+ * sni_ave.c - Socionext UniPhier AVE ethernet driver
+ * Copyright 2014 Panasonic Corporation
+ * Copyright 2015-2017 Socionext Inc.
+ */
+
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/etherdevice.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/iopoll.h>
+#include <linux/mii.h>
+#include <linux/module.h>
+#include <linux/netdevice.h>
+#include <linux/of_net.h>
+#include <linux/of_mdio.h>
+#include <linux/of_platform.h>
+#include <linux/phy.h>
+#include <linux/reset.h>
+#include <linux/types.h>
+#include <linux/u64_stats_sync.h>
+
+/* General Register Group */
+#define AVE_IDR 0x000 /* ID */
+#define AVE_VR 0x004 /* Version */
+#define AVE_GRR 0x008 /* Global Reset */
+#define AVE_CFGR 0x00c /* Configuration */
+
+/* Interrupt Register Group */
+#define AVE_GIMR 0x100 /* Global Interrupt Mask */
+#define AVE_GISR 0x104 /* Global Interrupt Status */
+
+/* MAC Register Group */
+#define AVE_TXCR 0x200 /* TX Setup */
+#define AVE_RXCR 0x204 /* RX Setup */
+#define AVE_RXMAC1R 0x208 /* MAC address (lower) */
+#define AVE_RXMAC2R 0x20c /* MAC address (upper) */
+#define AVE_MDIOCTR 0x214 /* MDIO Control */
+#define AVE_MDIOAR 0x218 /* MDIO Address */
+#define AVE_MDIOWDR 0x21c /* MDIO Data */
+#define AVE_MDIOSR 0x220 /* MDIO Status */
+#define AVE_MDIORDR 0x224 /* MDIO Rd Data */
+
+/* Descriptor Control Register Group */
+#define AVE_DESCC 0x300 /* Descriptor Control */
+#define AVE_TXDC 0x304 /* TX Descriptor Configuration */
+#define AVE_RXDC0 0x308 /* RX Descriptor Ring0 Configuration */
+#define AVE_IIRQC 0x34c /* Interval IRQ Control */
+
+/* Packet Filter Register Group */
+#define AVE_PKTF_BASE 0x800 /* PF Base Address */
+#define AVE_PFMBYTE_BASE 0xd00 /* PF Mask Byte Base Address */
+#define AVE_PFMBIT_BASE 0xe00 /* PF Mask Bit Base Address */
+#define AVE_PFSEL_BASE 0xf00 /* PF Selector Base Address */
+#define AVE_PFEN 0xffc /* Packet Filter Enable */
+#define AVE_PKTF(ent) (AVE_PKTF_BASE + (ent) * 0x40)
+#define AVE_PFMBYTE(ent) (AVE_PFMBYTE_BASE + (ent) * 8)
+#define AVE_PFMBIT(ent) (AVE_PFMBIT_BASE + (ent) * 4)
+#define AVE_PFSEL(ent) (AVE_PFSEL_BASE + (ent) * 4)
+
+/* 64bit descriptor memory */
+#define AVE_DESC_SIZE_64 12 /* Descriptor Size */
+
+#define AVE_TXDM_64 0x1000 /* Tx Descriptor Memory */
+#define AVE_RXDM_64 0x1c00 /* Rx Descriptor Memory */
+
+#define AVE_TXDM_SIZE_64 0x0ba0 /* Tx Descriptor Memory Size 3KB */
+#define AVE_RXDM_SIZE_64 0x6000 /* Rx Descriptor Memory Size 24KB */
+
+/* 32bit descriptor memory */
+#define AVE_DESC_SIZE_32 8 /* Descriptor Size */
+
+#define AVE_TXDM_32 0x1000 /* Tx Descriptor Memory */
+#define AVE_RXDM_32 0x1800 /* Rx Descriptor Memory */
+
+#define AVE_TXDM_SIZE_32 0x07c0 /* Tx Descriptor Memory Size 2KB */
+#define AVE_RXDM_SIZE_32 0x4000 /* Rx Descriptor Memory Size 16KB */
+
+/* RMII Bridge Register Group */
+#define AVE_RSTCTRL 0x8028 /* Reset control */
+#define AVE_RSTCTRL_RMIIRST BIT(16)
+#define AVE_LINKSEL 0x8034 /* Link speed setting */
+#define AVE_LINKSEL_100M BIT(0)
+
+/* AVE_GRR */
+#define AVE_GRR_RXFFR BIT(5) /* Reset RxFIFO */
+#define AVE_GRR_PHYRST BIT(4) /* Reset external PHY */
+#define AVE_GRR_GRST BIT(0) /* Reset all MAC */
+
+/* AVE_CFGR */
+#define AVE_CFGR_FLE BIT(31) /* Filter Function */
+#define AVE_CFGR_CHE BIT(30) /* Checksum Function */
+#define AVE_CFGR_MII BIT(27) /* Func mode (1:MII/RMII, 0:RGMII) */
+#define AVE_CFGR_IPFCEN BIT(24) /* IP fragment sum Enable */
+
+/* AVE_GISR (common with GIMR) */
+#define AVE_GI_PHY BIT(24) /* PHY interrupt */
+#define AVE_GI_TX BIT(16) /* Tx complete */
+#define AVE_GI_RXERR BIT(8) /* Receive frame more than max size */
+#define AVE_GI_RXOVF BIT(7) /* Overflow at the RxFIFO */
+#define AVE_GI_RXDROP BIT(6) /* Drop packet */
+#define AVE_GI_RXIINT BIT(5) /* Interval interrupt */
+
+/* AVE_TXCR */
+#define AVE_TXCR_FLOCTR BIT(18) /* Flow control */
+#define AVE_TXCR_TXSPD_1G BIT(17)
+#define AVE_TXCR_TXSPD_100 BIT(16)
+
+/* AVE_RXCR */
+#define AVE_RXCR_RXEN BIT(30) /* Rx enable */
+#define AVE_RXCR_FDUPEN BIT(22) /* Interface mode */
+#define AVE_RXCR_FLOCTR BIT(21) /* Flow control */
+#define AVE_RXCR_AFEN BIT(19) /* MAC address filter */
+#define AVE_RXCR_DRPEN BIT(18) /* Drop pause frame */
+#define AVE_RXCR_MPSIZ_MASK GENMASK(10, 0)
+
+/* AVE_MDIOCTR */
+#define AVE_MDIOCTR_RREQ BIT(3) /* Read request */
+#define AVE_MDIOCTR_WREQ BIT(2) /* Write request */
+
+/* AVE_MDIOSR */
+#define AVE_MDIOSR_STS BIT(0) /* access status */
+
+/* AVE_DESCC */
+#define AVE_DESCC_STATUS_MASK GENMASK(31, 16)
+#define AVE_DESCC_RD0 BIT(8) /* Enable Rx descriptor Ring0 */
+#define AVE_DESCC_RDSTP BIT(4) /* Pause Rx descriptor */
+#define AVE_DESCC_TD BIT(0) /* Enable Tx descriptor */
+
+/* AVE_TXDC */
+#define AVE_TXDC_SIZE GENMASK(27, 16) /* Size of Tx descriptor */
+#define AVE_TXDC_ADDR GENMASK(11, 0) /* Start address */
+#define AVE_TXDC_ADDR_START 0
+
+/* AVE_RXDC0 */
+#define AVE_RXDC0_SIZE GENMASK(30, 16) /* Size of Rx descriptor */
+#define AVE_RXDC0_ADDR GENMASK(14, 0) /* Start address */
+#define AVE_RXDC0_ADDR_START 0
+
+/* AVE_IIRQC */
+#define AVE_IIRQC_EN0 BIT(27) /* Enable interval interrupt Ring0 */
+#define AVE_IIRQC_BSCK GENMASK(15, 0) /* Interval count unit */
+
+/* Command status for descriptor */
+#define AVE_STS_OWN BIT(31) /* Descriptor ownership */
+#define AVE_STS_INTR BIT(29) /* Request for interrupt */
+#define AVE_STS_OK BIT(27) /* Normal transmit */
+/* TX */
+#define AVE_STS_NOCSUM BIT(28) /* No use HW checksum */
+#define AVE_STS_1ST BIT(26) /* Head of buffer chain */
+#define AVE_STS_LAST BIT(25) /* Tail of buffer chain */
+#define AVE_STS_OWC BIT(21) /* Out of window,Late Collision */
+#define AVE_STS_EC BIT(20) /* Excess collision occurred */
+#define AVE_STS_PKTLEN_TX_MASK GENMASK(15, 0)
+/* RX */
+#define AVE_STS_CSSV BIT(21) /* Checksum check performed */
+#define AVE_STS_CSER BIT(20) /* Checksum error detected */
+#define AVE_STS_PKTLEN_RX_MASK GENMASK(10, 0)
+
+/* Packet filter */
+#define AVE_PFMBYTE_MASK0 (GENMASK(31, 8) | GENMASK(5, 0))
+#define AVE_PFMBYTE_MASK1 GENMASK(25, 0)
+#define AVE_PFMBIT_MASK GENMASK(15, 0)
+
+#define AVE_PF_SIZE 17 /* Number of all packet filter */
+#define AVE_PF_MULTICAST_SIZE 7 /* Number of multicast filter */
+
+#define AVE_PFNUM_FILTER 0 /* No.0 */
+#define AVE_PFNUM_UNICAST 1 /* No.1 */
+#define AVE_PFNUM_BROADCAST 2 /* No.2 */
+#define AVE_PFNUM_MULTICAST 11 /* No.11-17 */
+
+/* NETIF Message control */
+#define AVE_DEFAULT_MSG_ENABLE (NETIF_MSG_DRV | \
+ NETIF_MSG_PROBE | \
+ NETIF_MSG_LINK | \
+ NETIF_MSG_TIMER | \
+ NETIF_MSG_IFDOWN | \
+ NETIF_MSG_IFUP | \
+ NETIF_MSG_RX_ERR | \
+ NETIF_MSG_TX_ERR)
+
+/* Parameter for descriptor */
+#define AVE_NR_TXDESC 32 /* Tx descriptor */
+#define AVE_NR_RXDESC 64 /* Rx descriptor */
+
+#define AVE_DESC_OFS_CMDSTS 0
+#define AVE_DESC_OFS_ADDRL 4
+#define AVE_DESC_OFS_ADDRU 8
+
+/* Parameter for ethernet frame */
+#define AVE_MAX_ETHFRAME 1518
+
+/* Parameter for interrupt */
+#define AVE_INTM_COUNT 20
+#define AVE_FORCE_TXINTCNT 1
+
+#define IS_DESC_64BIT(p) ((p)->data->is_desc_64bit)
+
+enum desc_id {
+ AVE_DESCID_RX,
+ AVE_DESCID_TX,
+};
+
+enum desc_state {
+ AVE_DESC_RX_PERMIT,
+ AVE_DESC_RX_SUSPEND,
+ AVE_DESC_START,
+ AVE_DESC_STOP,
+};
+
+struct ave_desc {
+ struct sk_buff *skbs;
+ dma_addr_t skbs_dma;
+ size_t skbs_dmalen;
+};
+
+struct ave_desc_info {
+ u32 ndesc; /* number of descriptor */
+ u32 daddr; /* start address of descriptor */
+ u32 proc_idx; /* index of processing packet */
+ u32 done_idx; /* index of processed packet */
+ struct ave_desc *desc; /* skb info related descriptor */
+};
+
+struct ave_soc_data {
+ bool is_desc_64bit;
+};
+
+struct ave_stats {
+ struct u64_stats_sync syncp;
+ u64 packets;
+ u64 bytes;
+ u64 errors;
+ u64 dropped;
+ u64 collisions;
+ u64 fifo_errors;
+};
+
+struct ave_private {
+ void __iomem *base;
+ int irq;
+ int phy_id;
+ unsigned int desc_size;
+ u32 msg_enable;
+ struct clk *clk;
+ struct reset_control *rst;
+ phy_interface_t phy_mode;
+ struct phy_device *phydev;
+ struct mii_bus *mdio;
+
+ /* stats */
+ struct ave_stats stats_rx;
+ struct ave_stats stats_tx;
+
+ /* NAPI support */
+ struct net_device *ndev;
+ struct napi_struct napi_rx;
+ struct napi_struct napi_tx;
+
+ /* descriptor */
+ struct ave_desc_info rx;
+ struct ave_desc_info tx;
+
+ /* flow control */
+ int pause_auto;
+ int pause_rx;
+ int pause_tx;
+
+ const struct ave_soc_data *data;
+};
+
+static u32 ave_desc_read(struct net_device *ndev, enum desc_id id, int entry,
+ int offset)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 addr = (id == AVE_DESCID_TX) ? priv->tx.daddr : priv->rx.daddr;
+
+ addr += entry * priv->desc_size + offset;
+
+ return readl(priv->base + addr);
+}
+
+static u32 ave_desc_read_cmdsts(struct net_device *ndev, enum desc_id id,
+ int entry)
+{
+ return ave_desc_read(ndev, id, entry, AVE_DESC_OFS_CMDSTS);
+}
+
+static void ave_desc_write(struct net_device *ndev, enum desc_id id,
+ int entry, int offset, u32 val)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 addr = (id == AVE_DESCID_TX) ? priv->tx.daddr : priv->rx.daddr;
+
+ addr += entry * priv->desc_size + offset;
+
+ writel(val, priv->base + addr);
+}
+
+static void ave_desc_write_cmdsts(struct net_device *ndev, enum desc_id id,
+ int entry, u32 val)
+{
+ ave_desc_write(ndev, id, entry, AVE_DESC_OFS_CMDSTS, val);
+}
+
+static void ave_desc_write_addr(struct net_device *ndev, enum desc_id id,
+ int entry, dma_addr_t paddr)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ ave_desc_write(ndev, id, entry, AVE_DESC_OFS_ADDRL,
+ lower_32_bits(paddr));
+ if (IS_DESC_64BIT(priv))
+ ave_desc_write(ndev, id,
+ entry, AVE_DESC_OFS_ADDRU,
+ upper_32_bits(paddr));
+}
+
+static u32 ave_irq_disable_all(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 ret;
+
+ ret = readl(priv->base + AVE_GIMR);
+ writel(0, priv->base + AVE_GIMR);
+
+ return ret;
+}
+
+static void ave_irq_restore(struct net_device *ndev, u32 val)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ writel(val, priv->base + AVE_GIMR);
+}
+
+static void ave_irq_enable(struct net_device *ndev, u32 bitflag)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ writel(readl(priv->base + AVE_GIMR) | bitflag, priv->base + AVE_GIMR);
+ writel(bitflag, priv->base + AVE_GISR);
+}
+
+static void ave_hw_write_macaddr(struct net_device *ndev,
+ const unsigned char *mac_addr,
+ int reg1, int reg2)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ writel(mac_addr[0] | mac_addr[1] << 8 |
+ mac_addr[2] << 16 | mac_addr[3] << 24, priv->base + reg1);
+ writel(mac_addr[4] | mac_addr[5] << 8, priv->base + reg2);
+}
+
+static void ave_hw_read_version(struct net_device *ndev, char *buf, int len)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 major, minor, vr;
+
+ vr = readl(priv->base + AVE_VR);
+ major = (vr & GENMASK(15, 8)) >> 8;
+ minor = (vr & GENMASK(7, 0));
+ snprintf(buf, len, "v%u.%u", major, minor);
+}
+
+static void ave_ethtool_get_drvinfo(struct net_device *ndev,
+ struct ethtool_drvinfo *info)
+{
+ struct device *dev = ndev->dev.parent;
+
+ strlcpy(info->driver, dev->driver->name, sizeof(info->driver));
+ strlcpy(info->bus_info, dev_name(dev), sizeof(info->bus_info));
+ ave_hw_read_version(ndev, info->fw_version, sizeof(info->fw_version));
+}
+
+static u32 ave_ethtool_get_msglevel(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ return priv->msg_enable;
+}
+
+static void ave_ethtool_set_msglevel(struct net_device *ndev, u32 val)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ priv->msg_enable = val;
+}
+
+static void ave_ethtool_get_wol(struct net_device *ndev,
+ struct ethtool_wolinfo *wol)
+{
+ wol->supported = 0;
+ wol->wolopts = 0;
+
+ if (ndev->phydev)
+ phy_ethtool_get_wol(ndev->phydev, wol);
+}
+
+static int ave_ethtool_set_wol(struct net_device *ndev,
+ struct ethtool_wolinfo *wol)
+{
+ int ret;
+
+ if (!ndev->phydev ||
+ (wol->wolopts & (WAKE_ARP | WAKE_MAGICSECURE)))
+ return -EOPNOTSUPP;
+
+ ret = phy_ethtool_set_wol(ndev->phydev, wol);
+ if (!ret)
+ device_set_wakeup_enable(&ndev->dev, !!wol->wolopts);
+
+ return ret;
+}
+
+static void ave_ethtool_get_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *pause)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ pause->autoneg = priv->pause_auto;
+ pause->rx_pause = priv->pause_rx;
+ pause->tx_pause = priv->pause_tx;
+}
+
+static int ave_ethtool_set_pauseparam(struct net_device *ndev,
+ struct ethtool_pauseparam *pause)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ struct phy_device *phydev = ndev->phydev;
+
+ if (!phydev)
+ return -EINVAL;
+
+ priv->pause_auto = pause->autoneg;
+ priv->pause_rx = pause->rx_pause;
+ priv->pause_tx = pause->tx_pause;
+
+ phydev->advertising &= ~(ADVERTISED_Pause | ADVERTISED_Asym_Pause);
+ if (pause->rx_pause)
+ phydev->advertising |= ADVERTISED_Pause | ADVERTISED_Asym_Pause;
+ if (pause->tx_pause)
+ phydev->advertising ^= ADVERTISED_Asym_Pause;
+
+ if (pause->autoneg) {
+ if (netif_running(ndev))
+ phy_start_aneg(phydev);
+ }
+
+ return 0;
+}
+
+static const struct ethtool_ops ave_ethtool_ops = {
+ .get_link_ksettings = phy_ethtool_get_link_ksettings,
+ .set_link_ksettings = phy_ethtool_set_link_ksettings,
+ .get_drvinfo = ave_ethtool_get_drvinfo,
+ .nway_reset = phy_ethtool_nway_reset,
+ .get_link = ethtool_op_get_link,
+ .get_msglevel = ave_ethtool_get_msglevel,
+ .set_msglevel = ave_ethtool_set_msglevel,
+ .get_wol = ave_ethtool_get_wol,
+ .set_wol = ave_ethtool_set_wol,
+ .get_pauseparam = ave_ethtool_get_pauseparam,
+ .set_pauseparam = ave_ethtool_set_pauseparam,
+};
+
+static int ave_mdiobus_read(struct mii_bus *bus, int phyid, int regnum)
+{
+ struct net_device *ndev = bus->priv;
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 mdioctl, mdiosr;
+ int ret;
+
+ /* write address */
+ writel((phyid << 8) | regnum, priv->base + AVE_MDIOAR);
+
+ /* read request */
+ mdioctl = readl(priv->base + AVE_MDIOCTR);
+ writel((mdioctl | AVE_MDIOCTR_RREQ) & ~AVE_MDIOCTR_WREQ,
+ priv->base + AVE_MDIOCTR);
+
+ ret = readl_poll_timeout(priv->base + AVE_MDIOSR, mdiosr,
+ !(mdiosr & AVE_MDIOSR_STS), 20, 2000);
+ if (ret) {
+ netdev_err(ndev, "failed to read (phy:%d reg:%x)\n",
+ phyid, regnum);
+ return ret;
+ }
+
+ return readl(priv->base + AVE_MDIORDR) & GENMASK(15, 0);
+}
+
+static int ave_mdiobus_write(struct mii_bus *bus,
+ int phyid, int regnum, u16 val)
+{
+ struct net_device *ndev = bus->priv;
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 mdioctl, mdiosr;
+ int ret;
+
+ /* write address */
+ writel((phyid << 8) | regnum, priv->base + AVE_MDIOAR);
+
+ /* write data */
+ writel(val, priv->base + AVE_MDIOWDR);
+
+ /* write request */
+ mdioctl = readl(priv->base + AVE_MDIOCTR);
+ writel((mdioctl | AVE_MDIOCTR_WREQ) & ~AVE_MDIOCTR_RREQ,
+ priv->base + AVE_MDIOCTR);
+
+ ret = readl_poll_timeout(priv->base + AVE_MDIOSR, mdiosr,
+ !(mdiosr & AVE_MDIOSR_STS), 20, 2000);
+ if (ret)
+ netdev_err(ndev, "failed to write (phy:%d reg:%x)\n",
+ phyid, regnum);
+
+ return ret;
+}
+
+static int ave_dma_map(struct net_device *ndev, struct ave_desc *desc,
+ void *ptr, size_t len,
+ enum dma_data_direction dir, dma_addr_t *paddr)
+{
+ dma_addr_t map_addr;
+
+ map_addr = dma_map_single(ndev->dev.parent, ptr, len, dir);
+ if (unlikely(dma_mapping_error(ndev->dev.parent, map_addr)))
+ return -ENOMEM;
+
+ desc->skbs_dma = map_addr;
+ desc->skbs_dmalen = len;
+ *paddr = map_addr;
+
+ return 0;
+}
+
+static void ave_dma_unmap(struct net_device *ndev, struct ave_desc *desc,
+ enum dma_data_direction dir)
+{
+ if (!desc->skbs_dma)
+ return;
+
+ dma_unmap_single(ndev->dev.parent,
+ desc->skbs_dma, desc->skbs_dmalen, dir);
+ desc->skbs_dma = 0;
+}
+
+/* Prepare Rx descriptor and memory */
+static int ave_rxdesc_prepare(struct net_device *ndev, int entry)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ struct sk_buff *skb;
+ dma_addr_t paddr;
+ int ret;
+
+ skb = priv->rx.desc[entry].skbs;
+ if (!skb) {
+ skb = netdev_alloc_skb_ip_align(ndev,
+ AVE_MAX_ETHFRAME);
+ if (!skb) {
+ netdev_err(ndev, "can't allocate skb for Rx\n");
+ return -ENOMEM;
+ }
+ }
+
+ /* set disable to cmdsts */
+ ave_desc_write_cmdsts(ndev, AVE_DESCID_RX, entry,
+ AVE_STS_INTR | AVE_STS_OWN);
+
+ /* map Rx buffer
+ * Rx buffer set to the Rx descriptor has two restrictions:
+ * - Rx buffer address is 4 byte aligned.
+ * - Rx buffer begins with 2 byte headroom, and data will be put from
+ * (buffer + 2).
+ * To satisfy this, specify the address to put back the buffer
+ * pointer advanced by NET_IP_ALIGN by netdev_alloc_skb_ip_align(),
+ * and expand the map size by NET_IP_ALIGN.
+ */
+ ret = ave_dma_map(ndev, &priv->rx.desc[entry],
+ skb->data - NET_IP_ALIGN,
+ AVE_MAX_ETHFRAME + NET_IP_ALIGN,
+ DMA_FROM_DEVICE, &paddr);
+ if (ret) {
+ netdev_err(ndev, "can't map skb for Rx\n");
+ dev_kfree_skb_any(skb);
+ return ret;
+ }
+ priv->rx.desc[entry].skbs = skb;
+
+ /* set buffer pointer */
+ ave_desc_write_addr(ndev, AVE_DESCID_RX, entry, paddr);
+
+ /* set enable to cmdsts */
+ ave_desc_write_cmdsts(ndev, AVE_DESCID_RX, entry,
+ AVE_STS_INTR | AVE_MAX_ETHFRAME);
+
+ return ret;
+}
+
+/* Switch state of descriptor */
+static int ave_desc_switch(struct net_device *ndev, enum desc_state state)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ int ret = 0;
+ u32 val;
+
+ switch (state) {
+ case AVE_DESC_START:
+ writel(AVE_DESCC_TD | AVE_DESCC_RD0, priv->base + AVE_DESCC);
+ break;
+
+ case AVE_DESC_STOP:
+ writel(0, priv->base + AVE_DESCC);
+ if (readl_poll_timeout(priv->base + AVE_DESCC, val, !val,
+ 150, 15000)) {
+ netdev_err(ndev, "can't stop descriptor\n");
+ ret = -EBUSY;
+ }
+ break;
+
+ case AVE_DESC_RX_SUSPEND:
+ val = readl(priv->base + AVE_DESCC);
+ val |= AVE_DESCC_RDSTP;
+ val &= ~AVE_DESCC_STATUS_MASK;
+ writel(val, priv->base + AVE_DESCC);
+ if (readl_poll_timeout(priv->base + AVE_DESCC, val,
+ val & (AVE_DESCC_RDSTP << 16),
+ 150, 150000)) {
+ netdev_err(ndev, "can't suspend descriptor\n");
+ ret = -EBUSY;
+ }
+ break;
+
+ case AVE_DESC_RX_PERMIT:
+ val = readl(priv->base + AVE_DESCC);
+ val &= ~AVE_DESCC_RDSTP;
+ val &= ~AVE_DESCC_STATUS_MASK;
+ writel(val, priv->base + AVE_DESCC);
+ break;
+
+ default:
+ ret = -EINVAL;
+ break;
+ }
+
+ return ret;
+}
+
+static int ave_tx_complete(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 proc_idx, done_idx, ndesc, cmdsts;
+ unsigned int nr_freebuf = 0;
+ unsigned int tx_packets = 0;
+ unsigned int tx_bytes = 0;
+
+ proc_idx = priv->tx.proc_idx;
+ done_idx = priv->tx.done_idx;
+ ndesc = priv->tx.ndesc;
+
+ /* free pre-stored skb from done_idx to proc_idx */
+ while (proc_idx != done_idx) {
+ cmdsts = ave_desc_read_cmdsts(ndev, AVE_DESCID_TX, done_idx);
+
+ /* do nothing if owner is HW (==1 for Tx) */
+ if (cmdsts & AVE_STS_OWN)
+ break;
+
+ /* check Tx status and updates statistics */
+ if (cmdsts & AVE_STS_OK) {
+ tx_bytes += cmdsts & AVE_STS_PKTLEN_TX_MASK;
+ /* success */
+ if (cmdsts & AVE_STS_LAST)
+ tx_packets++;
+ } else {
+ /* error */
+ if (cmdsts & AVE_STS_LAST) {
+ priv->stats_tx.errors++;
+ if (cmdsts & (AVE_STS_OWC | AVE_STS_EC))
+ priv->stats_tx.collisions++;
+ }
+ }
+
+ /* release skb */
+ if (priv->tx.desc[done_idx].skbs) {
+ ave_dma_unmap(ndev, &priv->tx.desc[done_idx],
+ DMA_TO_DEVICE);
+ dev_consume_skb_any(priv->tx.desc[done_idx].skbs);
+ priv->tx.desc[done_idx].skbs = NULL;
+ nr_freebuf++;
+ }
+ done_idx = (done_idx + 1) % ndesc;
+ }
+
+ priv->tx.done_idx = done_idx;
+
+ /* update stats */
+ u64_stats_update_begin(&priv->stats_tx.syncp);
+ priv->stats_tx.packets += tx_packets;
+ priv->stats_tx.bytes += tx_bytes;
+ u64_stats_update_end(&priv->stats_tx.syncp);
+
+ /* wake queue for freeing buffer */
+ if (unlikely(netif_queue_stopped(ndev)) && nr_freebuf)
+ netif_wake_queue(ndev);
+
+ return nr_freebuf;
+}
+
+static int ave_rx_receive(struct net_device *ndev, int num)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ struct sk_buff *skb;
+ u32 proc_idx, done_idx, ndesc, cmdsts;
+ int restpkt, npkts;
+ unsigned int pktlen;
+ unsigned int rx_packets = 0;
+ unsigned int rx_bytes = 0;
+
+ proc_idx = priv->rx.proc_idx;
+ done_idx = priv->rx.done_idx;
+ ndesc = priv->rx.ndesc;
+ restpkt = ((proc_idx + ndesc - 1) - done_idx) % ndesc;
+
+ for (npkts = 0; npkts < num; npkts++) {
+ /* we can't receive more packet, so fill desc quickly */
+ if (--restpkt < 0)
+ break;
+
+ cmdsts = ave_desc_read_cmdsts(ndev, AVE_DESCID_RX, proc_idx);
+
+ /* do nothing if owner is HW (==0 for Rx) */
+ if (!(cmdsts & AVE_STS_OWN))
+ break;
+
+ if (!(cmdsts & AVE_STS_OK)) {
+ priv->stats_rx.errors++;
+ proc_idx = (proc_idx + 1) % ndesc;
+ continue;
+ }
+
+ pktlen = cmdsts & AVE_STS_PKTLEN_RX_MASK;
+
+ /* get skbuff for rx */
+ skb = priv->rx.desc[proc_idx].skbs;
+ priv->rx.desc[proc_idx].skbs = NULL;
+
+ ave_dma_unmap(ndev, &priv->rx.desc[proc_idx], DMA_FROM_DEVICE);
+
+ skb->dev = ndev;
+ skb_put(skb, pktlen);
+ skb->protocol = eth_type_trans(skb, ndev);
+
+ if ((cmdsts & AVE_STS_CSSV) && (!(cmdsts & AVE_STS_CSER)))
+ skb->ip_summed = CHECKSUM_UNNECESSARY;
+
+ rx_packets++;
+ rx_bytes += pktlen;
+
+ netif_receive_skb(skb);
+
+ proc_idx = (proc_idx + 1) % ndesc;
+ }
+
+ priv->rx.proc_idx = proc_idx;
+
+ /* update stats */
+ u64_stats_update_begin(&priv->stats_rx.syncp);
+ priv->stats_rx.packets += rx_packets;
+ priv->stats_rx.bytes += rx_bytes;
+ u64_stats_update_end(&priv->stats_rx.syncp);
+
+ /* refill the Rx buffers */
+ while (proc_idx != done_idx) {
+ if (ave_rxdesc_prepare(ndev, done_idx))
+ break;
+ done_idx = (done_idx + 1) % ndesc;
+ }
+
+ priv->rx.done_idx = done_idx;
+
+ return npkts;
+}
+
+static int ave_napi_poll_rx(struct napi_struct *napi, int budget)
+{
+ struct ave_private *priv;
+ struct net_device *ndev;
+ int num;
+
+ priv = container_of(napi, struct ave_private, napi_rx);
+ ndev = priv->ndev;
+
+ num = ave_rx_receive(ndev, budget);
+ if (num < budget) {
+ napi_complete_done(napi, num);
+
+ /* enable Rx interrupt when NAPI finishes */
+ ave_irq_enable(ndev, AVE_GI_RXIINT);
+ }
+
+ return num;
+}
+
+static int ave_napi_poll_tx(struct napi_struct *napi, int budget)
+{
+ struct ave_private *priv;
+ struct net_device *ndev;
+ int num;
+
+ priv = container_of(napi, struct ave_private, napi_tx);
+ ndev = priv->ndev;
+
+ num = ave_tx_complete(ndev);
+ napi_complete(napi);
+
+ /* enable Tx interrupt when NAPI finishes */
+ ave_irq_enable(ndev, AVE_GI_TX);
+
+ return num;
+}
+
+static void ave_global_reset(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 val;
+
+ /* set config register */
+ val = AVE_CFGR_FLE | AVE_CFGR_IPFCEN | AVE_CFGR_CHE;
+ if (!phy_interface_mode_is_rgmii(priv->phy_mode))
+ val |= AVE_CFGR_MII;
+ writel(val, priv->base + AVE_CFGR);
+
+ /* reset RMII register */
+ val = readl(priv->base + AVE_RSTCTRL);
+ val &= ~AVE_RSTCTRL_RMIIRST;
+ writel(val, priv->base + AVE_RSTCTRL);
+
+ /* assert reset */
+ writel(AVE_GRR_GRST | AVE_GRR_PHYRST, priv->base + AVE_GRR);
+ msleep(20);
+
+ /* 1st, negate PHY reset only */
+ writel(AVE_GRR_GRST, priv->base + AVE_GRR);
+ msleep(40);
+
+ /* negate reset */
+ writel(0, priv->base + AVE_GRR);
+ msleep(40);
+
+ /* negate RMII register */
+ val = readl(priv->base + AVE_RSTCTRL);
+ val |= AVE_RSTCTRL_RMIIRST;
+ writel(val, priv->base + AVE_RSTCTRL);
+
+ ave_irq_disable_all(ndev);
+}
+
+static void ave_rxfifo_reset(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 rxcr_org;
+
+ /* save and disable MAC receive op */
+ rxcr_org = readl(priv->base + AVE_RXCR);
+ writel(rxcr_org & (~AVE_RXCR_RXEN), priv->base + AVE_RXCR);
+
+ /* suspend Rx descriptor */
+ ave_desc_switch(ndev, AVE_DESC_RX_SUSPEND);
+
+ /* receive all packets before descriptor starts */
+ ave_rx_receive(ndev, priv->rx.ndesc);
+
+ /* assert reset */
+ writel(AVE_GRR_RXFFR, priv->base + AVE_GRR);
+ usleep_range(40, 50);
+
+ /* negate reset */
+ writel(0, priv->base + AVE_GRR);
+ usleep_range(10, 20);
+
+ /* negate interrupt status */
+ writel(AVE_GI_RXOVF, priv->base + AVE_GISR);
+
+ /* permit descriptor */
+ ave_desc_switch(ndev, AVE_DESC_RX_PERMIT);
+
+ /* restore MAC reccieve op */
+ writel(rxcr_org, priv->base + AVE_RXCR);
+}
+
+static irqreturn_t ave_irq_handler(int irq, void *netdev)
+{
+ struct net_device *ndev = (struct net_device *)netdev;
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 gimr_val, gisr_val;
+
+ gimr_val = ave_irq_disable_all(ndev);
+
+ /* get interrupt status */
+ gisr_val = readl(priv->base + AVE_GISR);
+
+ /* PHY */
+ if (gisr_val & AVE_GI_PHY)
+ writel(AVE_GI_PHY, priv->base + AVE_GISR);
+
+ /* check exceeding packet */
+ if (gisr_val & AVE_GI_RXERR) {
+ writel(AVE_GI_RXERR, priv->base + AVE_GISR);
+ netdev_err(ndev, "receive a packet exceeding frame buffer\n");
+ }
+
+ gisr_val &= gimr_val;
+ if (!gisr_val)
+ goto exit_isr;
+
+ /* RxFIFO overflow */
+ if (gisr_val & AVE_GI_RXOVF) {
+ priv->stats_rx.fifo_errors++;
+ ave_rxfifo_reset(ndev);
+ goto exit_isr;
+ }
+
+ /* Rx drop */
+ if (gisr_val & AVE_GI_RXDROP) {
+ priv->stats_rx.dropped++;
+ writel(AVE_GI_RXDROP, priv->base + AVE_GISR);
+ }
+
+ /* Rx interval */
+ if (gisr_val & AVE_GI_RXIINT) {
+ napi_schedule(&priv->napi_rx);
+ /* still force to disable Rx interrupt until NAPI finishes */
+ gimr_val &= ~AVE_GI_RXIINT;
+ }
+
+ /* Tx completed */
+ if (gisr_val & AVE_GI_TX) {
+ napi_schedule(&priv->napi_tx);
+ /* still force to disable Tx interrupt until NAPI finishes */
+ gimr_val &= ~AVE_GI_TX;
+ }
+
+exit_isr:
+ ave_irq_restore(ndev, gimr_val);
+
+ return IRQ_HANDLED;
+}
+
+static int ave_pfsel_start(struct net_device *ndev, unsigned int entry)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 val;
+
+ if (WARN_ON(entry > AVE_PF_SIZE))
+ return -EINVAL;
+
+ val = readl(priv->base + AVE_PFEN);
+ writel(val | BIT(entry), priv->base + AVE_PFEN);
+
+ return 0;
+}
+
+static int ave_pfsel_stop(struct net_device *ndev, unsigned int entry)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 val;
+
+ if (WARN_ON(entry > AVE_PF_SIZE))
+ return -EINVAL;
+
+ val = readl(priv->base + AVE_PFEN);
+ writel(val & ~BIT(entry), priv->base + AVE_PFEN);
+
+ return 0;
+}
+
+static int ave_pfsel_set_macaddr(struct net_device *ndev,
+ unsigned int entry,
+ const unsigned char *mac_addr,
+ unsigned int set_size)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ if (WARN_ON(entry > AVE_PF_SIZE))
+ return -EINVAL;
+ if (WARN_ON(set_size > 6))
+ return -EINVAL;
+
+ ave_pfsel_stop(ndev, entry);
+
+ /* set MAC address for the filter */
+ ave_hw_write_macaddr(ndev, mac_addr,
+ AVE_PKTF(entry), AVE_PKTF(entry) + 4);
+
+ /* set byte mask */
+ writel(GENMASK(31, set_size) & AVE_PFMBYTE_MASK0,
+ priv->base + AVE_PFMBYTE(entry));
+ writel(AVE_PFMBYTE_MASK1, priv->base + AVE_PFMBYTE(entry) + 4);
+
+ /* set bit mask filter */
+ writel(AVE_PFMBIT_MASK, priv->base + AVE_PFMBIT(entry));
+
+ /* set selector to ring 0 */
+ writel(0, priv->base + AVE_PFSEL(entry));
+
+ /* restart filter */
+ ave_pfsel_start(ndev, entry);
+
+ return 0;
+}
+
+static void ave_pfsel_set_promisc(struct net_device *ndev,
+ unsigned int entry, u32 rxring)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ if (WARN_ON(entry > AVE_PF_SIZE))
+ return;
+
+ ave_pfsel_stop(ndev, entry);
+
+ /* set byte mask */
+ writel(AVE_PFMBYTE_MASK0, priv->base + AVE_PFMBYTE(entry));
+ writel(AVE_PFMBYTE_MASK1, priv->base + AVE_PFMBYTE(entry) + 4);
+
+ /* set bit mask filter */
+ writel(AVE_PFMBIT_MASK, priv->base + AVE_PFMBIT(entry));
+
+ /* set selector to rxring */
+ writel(rxring, priv->base + AVE_PFSEL(entry));
+
+ ave_pfsel_start(ndev, entry);
+}
+
+static void ave_pfsel_init(struct net_device *ndev)
+{
+ int i;
+ unsigned char bcast_mac[ETH_ALEN];
+
+ eth_broadcast_addr(bcast_mac);
+
+ for (i = 0; i < AVE_PF_SIZE; i++)
+ ave_pfsel_stop(ndev, i);
+
+ /* promiscious entry, select ring 0 */
+ ave_pfsel_set_promisc(ndev, AVE_PFNUM_FILTER, 0);
+
+ /* unicast entry */
+ ave_pfsel_set_macaddr(ndev, AVE_PFNUM_UNICAST, ndev->dev_addr, 6);
+
+ /* broadcast entry */
+ ave_pfsel_set_macaddr(ndev, AVE_PFNUM_BROADCAST, bcast_mac, 6);
+}
+
+static void ave_phy_adjust_link(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ struct phy_device *phydev = ndev->phydev;
+ u32 val, txcr, rxcr, rxcr_org;
+ u16 rmt_adv = 0, lcl_adv = 0;
+ u8 cap;
+
+ /* set RGMII speed */
+ val = readl(priv->base + AVE_TXCR);
+ val &= ~(AVE_TXCR_TXSPD_100 | AVE_TXCR_TXSPD_1G);
+
+ if (phy_interface_is_rgmii(phydev) && phydev->speed == SPEED_1000)
+ val |= AVE_TXCR_TXSPD_1G;
+ else if (phydev->speed == SPEED_100)
+ val |= AVE_TXCR_TXSPD_100;
+
+ writel(val, priv->base + AVE_TXCR);
+
+ /* set RMII speed (100M/10M only) */
+ if (!phy_interface_is_rgmii(phydev)) {
+ val = readl(priv->base + AVE_LINKSEL);
+ if (phydev->speed == SPEED_10)
+ val &= ~AVE_LINKSEL_100M;
+ else
+ val |= AVE_LINKSEL_100M;
+ writel(val, priv->base + AVE_LINKSEL);
+ }
+
+ /* check current RXCR/TXCR */
+ rxcr = readl(priv->base + AVE_RXCR);
+ txcr = readl(priv->base + AVE_TXCR);
+ rxcr_org = rxcr;
+
+ if (phydev->duplex) {
+ rxcr |= AVE_RXCR_FDUPEN;
+
+ if (phydev->pause)
+ rmt_adv |= LPA_PAUSE_CAP;
+ if (phydev->asym_pause)
+ rmt_adv |= LPA_PAUSE_ASYM;
+ if (phydev->advertising & ADVERTISED_Pause)
+ lcl_adv |= ADVERTISE_PAUSE_CAP;
+ if (phydev->advertising & ADVERTISED_Asym_Pause)
+ lcl_adv |= ADVERTISE_PAUSE_ASYM;
+
+ cap = mii_resolve_flowctrl_fdx(lcl_adv, rmt_adv);
+ if (cap & FLOW_CTRL_TX)
+ txcr |= AVE_TXCR_FLOCTR;
+ else
+ txcr &= ~AVE_TXCR_FLOCTR;
+ if (cap & FLOW_CTRL_RX)
+ rxcr |= AVE_RXCR_FLOCTR;
+ else
+ rxcr &= ~AVE_RXCR_FLOCTR;
+ } else {
+ rxcr &= ~AVE_RXCR_FDUPEN;
+ rxcr &= ~AVE_RXCR_FLOCTR;
+ txcr &= ~AVE_TXCR_FLOCTR;
+ }
+
+ if (rxcr_org != rxcr) {
+ /* disable Rx mac */
+ writel(rxcr & ~AVE_RXCR_RXEN, priv->base + AVE_RXCR);
+ /* change and enable TX/Rx mac */
+ writel(txcr, priv->base + AVE_TXCR);
+ writel(rxcr, priv->base + AVE_RXCR);
+ }
+
+ phy_print_status(phydev);
+}
+
+static void ave_macaddr_init(struct net_device *ndev)
+{
+ ave_hw_write_macaddr(ndev, ndev->dev_addr, AVE_RXMAC1R, AVE_RXMAC2R);
+
+ /* pfsel unicast entry */
+ ave_pfsel_set_macaddr(ndev, AVE_PFNUM_UNICAST, ndev->dev_addr, 6);
+}
+
+static int ave_init(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ struct device *dev = ndev->dev.parent;
+ struct device_node *np = dev->of_node, *mdio_np;
+ struct ethtool_wolinfo wol = { .cmd = ETHTOOL_GWOL };
+ struct phy_device *phydev;
+ int ret;
+
+ /* enable clk because of hw access until ndo_open */
+ ret = clk_prepare_enable(priv->clk);
+ if (ret) {
+ dev_err(dev, "can't enable clock\n");
+ return ret;
+ }
+ ret = reset_control_deassert(priv->rst);
+ if (ret) {
+ dev_err(dev, "can't deassert reset\n");
+ goto out_clk_disable;
+ }
+
+ ave_global_reset(ndev);
+
+ mdio_np = of_get_child_by_name(np, "mdio");
+ if (!mdio_np) {
+ dev_err(dev, "mdio node not found\n");
+ ret = -EINVAL;
+ goto out_reset_assert;
+ }
+ ret = of_mdiobus_register(priv->mdio, mdio_np);
+ of_node_put(mdio_np);
+ if (ret) {
+ dev_err(dev, "failed to register mdiobus\n");
+ goto out_reset_assert;
+ }
+
+ phydev = of_phy_get_and_connect(ndev, np, ave_phy_adjust_link);
+ if (!phydev) {
+ dev_err(dev, "could not attach to PHY\n");
+ ret = -ENODEV;
+ goto out_mdio_unregister;
+ }
+
+ priv->phydev = phydev;
+
+ phy_ethtool_get_wol(phydev, &wol);
+ device_set_wakeup_capable(&ndev->dev, !!wol.supported);
+
+ if (!phy_interface_is_rgmii(phydev)) {
+ phydev->supported &= ~PHY_GBIT_FEATURES;
+ phydev->supported |= PHY_BASIC_FEATURES;
+ }
+ phydev->supported |= SUPPORTED_Pause | SUPPORTED_Asym_Pause;
+
+ phy_attached_info(phydev);
+
+ return 0;
+
+out_mdio_unregister:
+ mdiobus_unregister(priv->mdio);
+out_reset_assert:
+ reset_control_assert(priv->rst);
+out_clk_disable:
+ clk_disable_unprepare(priv->clk);
+
+ return ret;
+}
+
+static void ave_uninit(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+
+ phy_disconnect(priv->phydev);
+ mdiobus_unregister(priv->mdio);
+
+ /* disable clk because of hw access after ndo_stop */
+ reset_control_assert(priv->rst);
+ clk_disable_unprepare(priv->clk);
+}
+
+static int ave_open(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ int entry;
+ int ret;
+ u32 val;
+
+ ret = request_irq(priv->irq, ave_irq_handler, IRQF_SHARED, ndev->name,
+ ndev);
+ if (ret)
+ return ret;
+
+ priv->tx.desc = kcalloc(priv->tx.ndesc, sizeof(*priv->tx.desc),
+ GFP_KERNEL);
+ if (!priv->tx.desc) {
+ ret = -ENOMEM;
+ goto out_free_irq;
+ }
+
+ priv->rx.desc = kcalloc(priv->rx.ndesc, sizeof(*priv->rx.desc),
+ GFP_KERNEL);
+ if (!priv->rx.desc) {
+ kfree(priv->tx.desc);
+ ret = -ENOMEM;
+ goto out_free_irq;
+ }
+
+ /* initialize Tx work and descriptor */
+ priv->tx.proc_idx = 0;
+ priv->tx.done_idx = 0;
+ for (entry = 0; entry < priv->tx.ndesc; entry++) {
+ ave_desc_write_cmdsts(ndev, AVE_DESCID_TX, entry, 0);
+ ave_desc_write_addr(ndev, AVE_DESCID_TX, entry, 0);
+ }
+ writel(AVE_TXDC_ADDR_START
+ | (((priv->tx.ndesc * priv->desc_size) << 16) & AVE_TXDC_SIZE),
+ priv->base + AVE_TXDC);
+
+ /* initialize Rx work and descriptor */
+ priv->rx.proc_idx = 0;
+ priv->rx.done_idx = 0;
+ for (entry = 0; entry < priv->rx.ndesc; entry++) {
+ if (ave_rxdesc_prepare(ndev, entry))
+ break;
+ }
+ writel(AVE_RXDC0_ADDR_START
+ | (((priv->rx.ndesc * priv->desc_size) << 16) & AVE_RXDC0_SIZE),
+ priv->base + AVE_RXDC0);
+
+ ave_desc_switch(ndev, AVE_DESC_START);
+
+ ave_pfsel_init(ndev);
+ ave_macaddr_init(ndev);
+
+ /* set Rx configuration */
+ /* full duplex, enable pause drop, enalbe flow control */
+ val = AVE_RXCR_RXEN | AVE_RXCR_FDUPEN | AVE_RXCR_DRPEN |
+ AVE_RXCR_FLOCTR | (AVE_MAX_ETHFRAME & AVE_RXCR_MPSIZ_MASK);
+ writel(val, priv->base + AVE_RXCR);
+
+ /* set Tx configuration */
+ /* enable flow control, disable loopback */
+ writel(AVE_TXCR_FLOCTR, priv->base + AVE_TXCR);
+
+ /* enable timer, clear EN,INTM, and mask interval unit(BSCK) */
+ val = readl(priv->base + AVE_IIRQC) & AVE_IIRQC_BSCK;
+ val |= AVE_IIRQC_EN0 | (AVE_INTM_COUNT << 16);
+ writel(val, priv->base + AVE_IIRQC);
+
+ val = AVE_GI_RXIINT | AVE_GI_RXOVF | AVE_GI_TX;
+ ave_irq_restore(ndev, val);
+
+ napi_enable(&priv->napi_rx);
+ napi_enable(&priv->napi_tx);
+
+ phy_start(ndev->phydev);
+ phy_start_aneg(ndev->phydev);
+ netif_start_queue(ndev);
+
+ return 0;
+
+out_free_irq:
+ disable_irq(priv->irq);
+ free_irq(priv->irq, ndev);
+
+ return ret;
+}
+
+static int ave_stop(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ int entry;
+
+ ave_irq_disable_all(ndev);
+ disable_irq(priv->irq);
+ free_irq(priv->irq, ndev);
+
+ netif_tx_disable(ndev);
+ phy_stop(ndev->phydev);
+ napi_disable(&priv->napi_tx);
+ napi_disable(&priv->napi_rx);
+
+ ave_desc_switch(ndev, AVE_DESC_STOP);
+
+ /* free Tx buffer */
+ for (entry = 0; entry < priv->tx.ndesc; entry++) {
+ if (!priv->tx.desc[entry].skbs)
+ continue;
+
+ ave_dma_unmap(ndev, &priv->tx.desc[entry], DMA_TO_DEVICE);
+ dev_kfree_skb_any(priv->tx.desc[entry].skbs);
+ priv->tx.desc[entry].skbs = NULL;
+ }
+ priv->tx.proc_idx = 0;
+ priv->tx.done_idx = 0;
+
+ /* free Rx buffer */
+ for (entry = 0; entry < priv->rx.ndesc; entry++) {
+ if (!priv->rx.desc[entry].skbs)
+ continue;
+
+ ave_dma_unmap(ndev, &priv->rx.desc[entry], DMA_FROM_DEVICE);
+ dev_kfree_skb_any(priv->rx.desc[entry].skbs);
+ priv->rx.desc[entry].skbs = NULL;
+ }
+ priv->rx.proc_idx = 0;
+ priv->rx.done_idx = 0;
+
+ kfree(priv->tx.desc);
+ kfree(priv->rx.desc);
+
+ return 0;
+}
+
+static int ave_start_xmit(struct sk_buff *skb, struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ u32 proc_idx, done_idx, ndesc, cmdsts;
+ int ret, freepkt;
+ dma_addr_t paddr;
+
+ proc_idx = priv->tx.proc_idx;
+ done_idx = priv->tx.done_idx;
+ ndesc = priv->tx.ndesc;
+ freepkt = ((done_idx + ndesc - 1) - proc_idx) % ndesc;
+
+ /* stop queue when not enough entry */
+ if (unlikely(freepkt < 1)) {
+ netif_stop_queue(ndev);
+ return NETDEV_TX_BUSY;
+ }
+
+ /* add padding for short packet */
+ if (skb_put_padto(skb, ETH_ZLEN)) {
+ priv->stats_tx.dropped++;
+ return NETDEV_TX_OK;
+ }
+
+ /* map Tx buffer
+ * Tx buffer set to the Tx descriptor doesn't have any restriction.
+ */
+ ret = ave_dma_map(ndev, &priv->tx.desc[proc_idx],
+ skb->data, skb->len, DMA_TO_DEVICE, &paddr);
+ if (ret) {
+ dev_kfree_skb_any(skb);
+ priv->stats_tx.dropped++;
+ return NETDEV_TX_OK;
+ }
+
+ priv->tx.desc[proc_idx].skbs = skb;
+
+ ave_desc_write_addr(ndev, AVE_DESCID_TX, proc_idx, paddr);
+
+ cmdsts = AVE_STS_OWN | AVE_STS_1ST | AVE_STS_LAST
+ | (skb->len & AVE_STS_PKTLEN_TX_MASK);
+
+ /* set interrupt per AVE_FORCE_TXINTCNT or when queue is stopped */
+ if (!(proc_idx % AVE_FORCE_TXINTCNT) || netif_queue_stopped(ndev))
+ cmdsts |= AVE_STS_INTR;
+
+ /* disable checksum calculation when skb doesn't calurate checksum */
+ if (skb->ip_summed == CHECKSUM_NONE ||
+ skb->ip_summed == CHECKSUM_UNNECESSARY)
+ cmdsts |= AVE_STS_NOCSUM;
+
+ ave_desc_write_cmdsts(ndev, AVE_DESCID_TX, proc_idx, cmdsts);
+
+ priv->tx.proc_idx = (proc_idx + 1) % ndesc;
+
+ return NETDEV_TX_OK;
+}
+
+static int ave_ioctl(struct net_device *ndev, struct ifreq *ifr, int cmd)
+{
+ return phy_mii_ioctl(ndev->phydev, ifr, cmd);
+}
+
+static void ave_set_rx_mode(struct net_device *ndev)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ struct netdev_hw_addr *hw_adr;
+ int count, mc_cnt = netdev_mc_count(ndev);
+ u32 val;
+ static const u8 v4multi_macadr[6] = {
+ 0x01, 0x00, 0x00, 0x00, 0x00, 0x00 };
+ static const u8 v6multi_macadr[6] = {
+ 0x33, 0x00, 0x00, 0x00, 0x00, 0x00 };
+
+ /* MAC addr filter enable for promiscious mode */
+ val = readl(priv->base + AVE_RXCR);
+ if (ndev->flags & IFF_PROMISC || !mc_cnt)
+ val &= ~AVE_RXCR_AFEN;
+ else
+ val |= AVE_RXCR_AFEN;
+ writel(val, priv->base + AVE_RXCR);
+
+ /* set all multicast address */
+ if ((ndev->flags & IFF_ALLMULTI) || mc_cnt > AVE_PF_MULTICAST_SIZE) {
+ ave_pfsel_set_macaddr(ndev, AVE_PFNUM_MULTICAST,
+ v4multi_macadr, 1);
+ ave_pfsel_set_macaddr(ndev, AVE_PFNUM_MULTICAST + 1,
+ v6multi_macadr, 1);
+ } else {
+ /* stop all multicast filter */
+ for (count = 0; count < AVE_PF_MULTICAST_SIZE; count++)
+ ave_pfsel_stop(ndev, AVE_PFNUM_MULTICAST + count);
+
+ /* set multicast addresses */
+ count = 0;
+ netdev_for_each_mc_addr(hw_adr, ndev) {
+ if (count == mc_cnt)
+ break;
+ ave_pfsel_set_macaddr(ndev, AVE_PFNUM_MULTICAST + count,
+ hw_adr->addr, 6);
+ count++;
+ }
+ }
+}
+
+static void ave_get_stats64(struct net_device *ndev,
+ struct rtnl_link_stats64 *stats)
+{
+ struct ave_private *priv = netdev_priv(ndev);
+ unsigned int start;
+
+ do {
+ start = u64_stats_fetch_begin_irq(&priv->stats_rx.syncp);
+ stats->rx_packets = priv->stats_rx.packets;
+ stats->rx_bytes = priv->stats_rx.bytes;
+ } while (u64_stats_fetch_retry_irq(&priv->stats_rx.syncp, start));
+
+ do {
+ start = u64_stats_fetch_begin_irq(&priv->stats_tx.syncp);
+ stats->tx_packets = priv->stats_tx.packets;
+ stats->tx_bytes = priv->stats_tx.bytes;
+ } while (u64_stats_fetch_retry_irq(&priv->stats_tx.syncp, start));
+
+ stats->rx_errors = priv->stats_rx.errors;
+ stats->tx_errors = priv->stats_tx.errors;
+ stats->rx_dropped = priv->stats_rx.dropped;
+ stats->tx_dropped = priv->stats_tx.dropped;
+ stats->rx_fifo_errors = priv->stats_rx.fifo_errors;
+ stats->collisions = priv->stats_tx.collisions;
+}
+
+static int ave_set_mac_address(struct net_device *ndev, void *p)
+{
+ int ret = eth_mac_addr(ndev, p);
+
+ if (ret)
+ return ret;
+
+ ave_macaddr_init(ndev);
+
+ return 0;
+}
+
+static const struct net_device_ops ave_netdev_ops = {
+ .ndo_init = ave_init,
+ .ndo_uninit = ave_uninit,
+ .ndo_open = ave_open,
+ .ndo_stop = ave_stop,
+ .ndo_start_xmit = ave_start_xmit,
+ .ndo_do_ioctl = ave_ioctl,
+ .ndo_set_rx_mode = ave_set_rx_mode,
+ .ndo_get_stats64 = ave_get_stats64,
+ .ndo_set_mac_address = ave_set_mac_address,
+};
+
+static int ave_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ struct device_node *np = dev->of_node;
+ struct ave_private *priv;
+ struct net_device *ndev;
+ struct resource *res;
+ const struct ave_soc_data *data;
+ const void *mac_addr;
+ phy_interface_t phy_mode;
+ void __iomem *base;
+ u32 ave_id;
+ u64 dma_mask;
+ int irq, ret;
+ char buf[ETHTOOL_FWVERS_LEN];
+
+ data = of_device_get_match_data(dev);
+ if (WARN_ON(!data))
+ return -EINVAL;
+
+ phy_mode = of_get_phy_mode(np);
+ if (phy_mode < 0) {
+ dev_err(dev, "phy-mode not found\n");
+ return -EINVAL;
+ }
+ if ((!phy_interface_mode_is_rgmii(phy_mode)) &&
+ phy_mode != PHY_INTERFACE_MODE_RMII &&
+ phy_mode != PHY_INTERFACE_MODE_MII) {
+ dev_err(dev, "phy-mode is invalid\n");
+ return -EINVAL;
+ }
+
+ irq = platform_get_irq(pdev, 0);
+ if (irq < 0) {
+ dev_err(dev, "IRQ not found\n");
+ return irq;
+ }
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ ndev = alloc_etherdev(sizeof(struct ave_private));
+ if (!ndev) {
+ dev_err(dev, "can't allocate ethernet device\n");
+ return -ENOMEM;
+ }
+
+ ndev->netdev_ops = &ave_netdev_ops;
+ ndev->ethtool_ops = &ave_ethtool_ops;
+ SET_NETDEV_DEV(ndev, dev);
+
+ ndev->features |= (NETIF_F_IP_CSUM | NETIF_F_RXCSUM);
+ ndev->hw_features |= (NETIF_F_IP_CSUM | NETIF_F_RXCSUM);
+
+ ndev->max_mtu = AVE_MAX_ETHFRAME - (ETH_HLEN + ETH_FCS_LEN);
+
+ mac_addr = of_get_mac_address(np);
+ if (mac_addr)
+ ether_addr_copy(ndev->dev_addr, mac_addr);
+
+ /* if the mac address is invalid, use random mac address */
+ if (!is_valid_ether_addr(ndev->dev_addr)) {
+ eth_hw_addr_random(ndev);
+ dev_warn(dev, "Using random MAC address: %pM\n",
+ ndev->dev_addr);
+ }
+
+ priv = netdev_priv(ndev);
+ priv->base = base;
+ priv->irq = irq;
+ priv->ndev = ndev;
+ priv->msg_enable = netif_msg_init(-1, AVE_DEFAULT_MSG_ENABLE);
+ priv->phy_mode = phy_mode;
+ priv->data = data;
+
+ if (IS_DESC_64BIT(priv)) {
+ priv->desc_size = AVE_DESC_SIZE_64;
+ priv->tx.daddr = AVE_TXDM_64;
+ priv->rx.daddr = AVE_RXDM_64;
+ dma_mask = DMA_BIT_MASK(64);
+ } else {
+ priv->desc_size = AVE_DESC_SIZE_32;
+ priv->tx.daddr = AVE_TXDM_32;
+ priv->rx.daddr = AVE_RXDM_32;
+ dma_mask = DMA_BIT_MASK(32);
+ }
+ ret = dma_set_mask(dev, dma_mask);
+ if (ret)
+ goto out_free_netdev;
+
+ priv->tx.ndesc = AVE_NR_TXDESC;
+ priv->rx.ndesc = AVE_NR_RXDESC;
+
+ u64_stats_init(&priv->stats_tx.syncp);
+ u64_stats_init(&priv->stats_rx.syncp);
+
+ priv->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(priv->clk)) {
+ ret = PTR_ERR(priv->clk);
+ goto out_free_netdev;
+ }
+
+ priv->rst = devm_reset_control_get_optional_shared(dev, NULL);
+ if (IS_ERR(priv->rst)) {
+ ret = PTR_ERR(priv->rst);
+ goto out_free_netdev;
+ }
+
+ priv->mdio = devm_mdiobus_alloc(dev);
+ if (!priv->mdio) {
+ ret = -ENOMEM;
+ goto out_free_netdev;
+ }
+ priv->mdio->priv = ndev;
+ priv->mdio->parent = dev;
+ priv->mdio->read = ave_mdiobus_read;
+ priv->mdio->write = ave_mdiobus_write;
+ priv->mdio->name = "uniphier-mdio";
+ snprintf(priv->mdio->id, MII_BUS_ID_SIZE, "%s-%x",
+ pdev->name, pdev->id);
+
+ /* Register as a NAPI supported driver */
+ netif_napi_add(ndev, &priv->napi_rx, ave_napi_poll_rx, priv->rx.ndesc);
+ netif_tx_napi_add(ndev, &priv->napi_tx, ave_napi_poll_tx,
+ priv->tx.ndesc);
+
+ ret = register_netdev(ndev);
+ if (ret) {
+ dev_err(dev, "failed to register netdevice\n");
+ goto out_del_napi;
+ }
+
+ platform_set_drvdata(pdev, ndev);
+
+ /* get ID and version */
+ ave_id = readl(priv->base + AVE_IDR);
+ ave_hw_read_version(ndev, buf, sizeof(buf));
+
+ dev_info(dev, "Socionext %c%c%c%c Ethernet IP %s (irq=%d, phy=%s)\n",
+ (ave_id >> 24) & 0xff, (ave_id >> 16) & 0xff,
+ (ave_id >> 8) & 0xff, (ave_id >> 0) & 0xff,
+ buf, priv->irq, phy_modes(phy_mode));
+
+ return 0;
+
+out_del_napi:
+ netif_napi_del(&priv->napi_rx);
+ netif_napi_del(&priv->napi_tx);
+out_free_netdev:
+ free_netdev(ndev);
+
+ return ret;
+}
+
+static int ave_remove(struct platform_device *pdev)
+{
+ struct net_device *ndev = platform_get_drvdata(pdev);
+ struct ave_private *priv = netdev_priv(ndev);
+
+ unregister_netdev(ndev);
+ netif_napi_del(&priv->napi_rx);
+ netif_napi_del(&priv->napi_tx);
+ free_netdev(ndev);
+
+ return 0;
+}
+
+static const struct ave_soc_data ave_pro4_data = {
+ .is_desc_64bit = false,
+};
+
+static const struct ave_soc_data ave_pxs2_data = {
+ .is_desc_64bit = false,
+};
+
+static const struct ave_soc_data ave_ld11_data = {
+ .is_desc_64bit = false,
+};
+
+static const struct ave_soc_data ave_ld20_data = {
+ .is_desc_64bit = true,
+};
+
+static const struct of_device_id of_ave_match[] = {
+ {
+ .compatible = "socionext,uniphier-pro4-ave4",
+ .data = &ave_pro4_data,
+ },
+ {
+ .compatible = "socionext,uniphier-pxs2-ave4",
+ .data = &ave_pxs2_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld11-ave4",
+ .data = &ave_ld11_data,
+ },
+ {
+ .compatible = "socionext,uniphier-ld20-ave4",
+ .data = &ave_ld20_data,
+ },
+ { /* Sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, of_ave_match);
+
+static struct platform_driver ave_driver = {
+ .probe = ave_probe,
+ .remove = ave_remove,
+ .driver = {
+ .name = "ave",
+ .of_match_table = of_ave_match,
+ },
+};
+module_platform_driver(ave_driver);
+
+MODULE_DESCRIPTION("Socionext UniPhier AVE ethernet driver");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related
* [PATCH net-next v6 1/2] dt-bindings: net: add DT bindings for Socionext UniPhier AVE
From: Kunihiko Hayashi @ 2017-12-14 10:05 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1513245910-15961-1-git-send-email-hayashi.kunihiko@socionext.com>
DT bindings for the AVE ethernet controller found on Socionext's
UniPhier platforms.
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Signed-off-by: Jassi Brar <jaswinder.singh@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
.../bindings/net/socionext,uniphier-ave4.txt | 48 ++++++++++++++++++++++
1 file changed, 48 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
diff --git a/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
new file mode 100644
index 0000000..4700377
--- /dev/null
+++ b/Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
@@ -0,0 +1,48 @@
+* Socionext AVE ethernet controller
+
+This describes the devicetree bindings for AVE ethernet controller
+implemented on Socionext UniPhier SoCs.
+
+Required properties:
+ - compatible: Should be
+ - "socionext,uniphier-pro4-ave4" : for Pro4 SoC
+ - "socionext,uniphier-pxs2-ave4" : for PXs2 SoC
+ - "socionext,uniphier-ld11-ave4" : for LD11 SoC
+ - "socionext,uniphier-ld20-ave4" : for LD20 SoC
+ - reg: Address where registers are mapped and size of region.
+ - interrupts: Should contain the MAC interrupt.
+ - phy-mode: See ethernet.txt in the same directory. Allow to choose
+ "rgmii", "rmii", or "mii" according to the PHY.
+ - phy-handle: Should point to the external phy device.
+ See ethernet.txt file in the same directory.
+ - clocks: A phandle to the clock for the MAC.
+
+Optional properties:
+ - resets: A phandle to the reset control for the MAC
+ - local-mac-address: See ethernet.txt in the same directory.
+
+Required subnode:
+ - mdio: Device tree subnode with the following required properties:
+ - #address-cells: Must be <1>.
+ - #size-cells: Must be <0>.
+ - reg: phy ID number, usually a small integer.
+
+Example:
+
+ ether: ethernet at 65000000 {
+ compatible = "socionext,uniphier-ld20-ave4";
+ reg = <0x65000000 0x8500>;
+ interrupts = <0 66 4>;
+ phy-mode = "rgmii";
+ phy-handle = <ðphy>;
+ clocks = <&sys_clk 6>;
+ resets = <&sys_rst 6>;
+ local-mac-address = [00 00 00 00 00 00];
+ mdio {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ ethphy: ethphy at 1 {
+ reg = <1>;
+ };
+ };
+ };
--
2.7.4
^ permalink raw reply related
* [PATCH net-next v6 0/2] add UniPhier AVE ethernet support
From: Kunihiko Hayashi @ 2017-12-14 10:05 UTC (permalink / raw)
To: linux-arm-kernel
This series adds support for Socionext AVE ethernet controller implemented
on UniPhier SoCs. This driver supports RGMII/RMII modes.
v5: https://www.spinics.net/lists/netdev/msg471330.html
The PHY patch included in v1 has already separated in:
http://www.spinics.net/lists/netdev/msg454595.html
Changes since v5:
- replace license boilerplate with SPDX Identifier
- remove inline directives and an unused function
Changes since v4:
- fix larger integer warning on AVE_PFMBYTE_MASK0
Changes since v3:
- remove checking dma address and use dma_set_mask() to restirct address
- replace ave_mdio_busywait() with read_poll_timeout()
- replace functions to access to registers with readl/writel() directly
- replace a function to access to macaddr with ave_hw_write_macaddr()
- change return value of ave_dma_map() to error value
- move mdiobus_unregister() from ave_remove() to ave_uninit()
- eliminate else block at the end of ave_dma_map()
- add mask definitions for packet filter
- sort bitmap definitions in descending order
- add error check to some functions
- rename and sort functions to clear sub-categories
- fix error value consistency
- remove unneeded initializers
- change type of constant arrays
Changes since v2:
- replace clk_get() with devm_clk_get()
- replace reset_control_get() with devm_reset_control_get_optional_shared()
- add error return when the error occurs on the above *_get functions
- sort soc data and compatible strings
- remove clearly obvious comments
- modify dt-bindings document consistent with these modifications
Changes since v1:
- add/remove devicetree properties and sub-node
- remove "internal-phy-interrupt" and "desc-bits" property
- add SoC data structures based on compatible strings
- add node operation to apply "mdio" sub-node
- add support for features
- add support for {get,set}_pauseparam and pause frame operations
- add support for ndo_get_stats64 instead of ndo_get_stats
- replace with desiable functions
- replace check for valid phy_mode with phy_interface{_mode}_is_rgmii()
- replace phy attach message with phy_attached_info()
- replace 32bit operation with {upper,lower}_32_bits() on ave_wdesc_addr()
- replace nway_reset and get_link with generic functions
- move operations to proper functions
- move phy_start_aneg() to ndo_open,
and remove unnecessary PHY interrupt operations
See http://www.spinics.net/lists/netdev/msg454590.html
- move irq initialization and descriptor memory allocation to ndo_open
- move initialization of reset and clock and mdiobus to ndo_init
- fix skbuffer operations
- fix skb alignment operations and add Rx buffer adjustment for descriptor
See http://www.spinics.net/lists/netdev/msg456014.html
- add error returns when dma_map_single() failed
- clean up code structures
- clean up wait-loop and wake-queue conditions
- add ave_wdesc_addr() and offset definitions
- add ave_macaddr_init() to clean up mac-address operation
- fix checking whether Tx entry is not enough
- fix supported features of phydev
- add necessary free/disable operations
- add phydev check on ave_{get,set}_wol()
- remove netif_carrier functions, phydev initializer, and Tx budget check
- change obsolate codes
- replace ndev->{base_addr,irq} with the members of ave_private
- rename goto labels and mask definitions, and remove unused codes
Kunihiko Hayashi (2):
dt-bindings: net: add DT bindings for Socionext UniPhier AVE
net: ethernet: socionext: add AVE ethernet driver
.../bindings/net/socionext,uniphier-ave4.txt | 48 +
drivers/net/ethernet/Kconfig | 1 +
drivers/net/ethernet/Makefile | 1 +
drivers/net/ethernet/socionext/Kconfig | 22 +
drivers/net/ethernet/socionext/Makefile | 5 +
drivers/net/ethernet/socionext/sni_ave.c | 1727 ++++++++++++++++++++
6 files changed, 1804 insertions(+)
create mode 100644 Documentation/devicetree/bindings/net/socionext,uniphier-ave4.txt
create mode 100644 drivers/net/ethernet/socionext/Kconfig
create mode 100644 drivers/net/ethernet/socionext/Makefile
create mode 100644 drivers/net/ethernet/socionext/sni_ave.c
--
2.7.4
^ permalink raw reply
* [PATCH v7 0/6] add clk controller driver for Meson-AXG SoC
From: Jerome Brunet @ 2017-12-14 10:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171211141348.22048-1-yixun.lan@amlogic.com>
On Mon, 2017-12-11 at 22:13 +0800, Yixun Lan wrote:
> Qiufang Dai (3):
> clk: meson-axg: add clocks dt-bindings required header
> clk: meson-axg: add clock controller drivers
> arm64: dts: meson-axg: add clock DT info for Meson AXG SoC
>
> Yixun Lan (3):
> clk: meson: make the spinlock naming more specific
> dt-bindings: clock: add compatible variant for the Meson-AXG
> arm64: dts: meson-axg: switch uart_ao clock to CLK81
>
> .../bindings/clock/amlogic,gxbb-clkc.txt | 7 +-
> arch/arm64/Kconfig.platforms | 1 +
> arch/arm64/boot/dts/amlogic/meson-axg-s400.dts | 2 +
> arch/arm64/boot/dts/amlogic/meson-axg.dtsi | 19 +-
> drivers/clk/meson/Kconfig | 8 +
> drivers/clk/meson/Makefile | 1 +
> drivers/clk/meson/axg.c | 936 +++++++++++++++++++++
> drivers/clk/meson/axg.h | 126 +++
> drivers/clk/meson/clkc.h | 2 +-
> drivers/clk/meson/gxbb.c | 112 +--
> drivers/clk/meson/meson8b.c | 24 +-
> include/dt-bindings/clock/axg-clkc.h | 71 ++
> 12 files changed, 1234 insertions(+), 75 deletions(-)
> create mode 100644 drivers/clk/meson/axg.c
> create mode 100644 drivers/clk/meson/axg.h
> create mode 100644 include/dt-bindings/clock/axg-clkc.h
Kevin,
I took the first 4 patches through clk-meson. I left the last 2 for you.
I have applied the DT bindings update separately.
Let me know if you have dependency on these new bindings and need a tag.
Cheers
Jerome
^ permalink raw reply
* [PATCH v7 4/6] clk: meson-axg: add clock controller drivers
From: Jerome Brunet @ 2017-12-14 9:59 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171211141348.22048-5-yixun.lan@amlogic.com>
On Mon, 2017-12-11 at 22:13 +0800, Yixun Lan wrote:
> From: Qiufang Dai <qiufang.dai@amlogic.com>
>
> Add clock controller drivers for Amlogic Meson-AXG SoC.
>
> Acked-by: Neil Armstrong <narmstrong@baylibre.com>
> Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Applied to next/drivers
Thx
> ---
> arch/arm64/Kconfig.platforms | 1 +
> drivers/clk/meson/Kconfig | 8 +
> drivers/clk/meson/Makefile | 1 +
> drivers/clk/meson/axg.c | 936 +++++++++++++++++++++++++++++++++++++++++++
> drivers/clk/meson/axg.h | 126 ++++++
> 5 files changed, 1072 insertions(+)
> create mode 100644 drivers/clk/meson/axg.c
> create mode 100644 drivers/clk/meson/axg.h
^ permalink raw reply
* [PATCH v7 3/6] clk: meson-axg: add clocks dt-bindings required header
From: Jerome Brunet @ 2017-12-14 9:58 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20171211141348.22048-4-yixun.lan@amlogic.com>
On Mon, 2017-12-11 at 22:13 +0800, Yixun Lan wrote:
> From: Qiufang Dai <qiufang.dai@amlogic.com>
>
> Add the required header for the clocks ID dt-bindings
> exported from various subsystem in the Meson-AXG SoC.
>
> Acked-by: Rob Herring <robh@kernel.org>
> Signed-off-by: Qiufang Dai <qiufang.dai@amlogic.com>
> Signed-off-by: Yixun Lan <yixun.lan@amlogic.com>
Applied to next/dt
Thx
> ---
> include/dt-bindings/clock/axg-clkc.h | 71 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 71 insertions(+)
> create mode 100644 include/dt-bindings/clock/axg-clkc.h
^ permalink raw reply
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox