* [PATCH v2 3/3] ARM: multi_v7_defconfig: enable STM32 RTC
From: Amelie Delaunay @ 2018-05-17 12:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558828-24456-1-git-send-email-amelie.delaunay@st.com>
Enable the STM32 Real Time Clock (RTC) driver, implemented on STM32MP1 SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/configs/multi_v7_defconfig | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm/configs/multi_v7_defconfig b/arch/arm/configs/multi_v7_defconfig
index 89167cd..8e02f86 100644
--- a/arch/arm/configs/multi_v7_defconfig
+++ b/arch/arm/configs/multi_v7_defconfig
@@ -863,6 +863,7 @@ CONFIG_RTC_DRV_SUN6I=y
CONFIG_RTC_DRV_SUNXI=y
CONFIG_RTC_DRV_MV=y
CONFIG_RTC_DRV_TEGRA=y
+CONFIG_RTC_DRV_STM32=y
CONFIG_RTC_DRV_CPCAP=m
CONFIG_DMADEVICES=y
CONFIG_DW_DMAC=y
--
2.7.4
^ permalink raw reply related
* [PATCH v2 2/3] ARM: dts: stm32: enable RTC on stm32mp157c-ed1
From: Amelie Delaunay @ 2018-05-17 12:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558828-24456-1-git-send-email-amelie.delaunay@st.com>
Enable RTC (Real Time Clock) on stm32mp157c-ed1 board.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c-ed1.dts | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c-ed1.dts b/arch/arm/boot/dts/stm32mp157c-ed1.dts
index ae33653..050c30d 100644
--- a/arch/arm/boot/dts/stm32mp157c-ed1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ed1.dts
@@ -68,6 +68,10 @@
status = "okay";
};
+&rtc {
+ status = "okay";
+};
+
&uart4 {
pinctrl-names = "default";
pinctrl-0 = <&uart4_pins_a>;
--
2.7.4
^ permalink raw reply related
* [PATCH v2 1/3] ARM: dts: stm32: add RTC support to stm32mp157c
From: Amelie Delaunay @ 2018-05-17 12:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558828-24456-1-git-send-email-amelie.delaunay@st.com>
Add support for RTC (Real Time Clock) to STM32MP157C SoC.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
arch/arm/boot/dts/stm32mp157c.dtsi | 9 +++++++++
1 file changed, 9 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index b66f673..df2d874 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -818,6 +818,15 @@
status = "disabled";
};
+ rtc: rtc at 5c004000 {
+ compatible = "st,stm32mp1-rtc";
+ reg = <0x5c004000 0x400>;
+ clocks = <&rcc RTCAPB>, <&rcc RTC>;
+ clock-names = "pclk", "rtc_ck";
+ interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH>;
+ status = "disabled";
+ };
+
i2c6: i2c at 5c009000 {
compatible = "st,stm32f7-i2c";
reg = <0x5c009000 0x400>;
--
2.7.4
^ permalink raw reply related
* [PATCH v2 0/3] Add STM32 RTC to stm32mp157c
From: Amelie Delaunay @ 2018-05-17 12:07 UTC (permalink / raw)
To: linux-arm-kernel
This series adds support for STM32 RTC to stm32mp157c SoC and enables it
on stm32mp157c-ed1 board.
---
Changes in v2:
* Enable STM32 RTC in multi_v7_defconfig
Amelie Delaunay (3):
ARM: dts: stm32: add RTC support to stm32mp157c
ARM: dts: stm32: enable RTC on stm32mp157c-ed1
ARM: multi_v7_defconfig: enable STM32 RTC
arch/arm/boot/dts/stm32mp157c-ed1.dts | 4 ++++
arch/arm/boot/dts/stm32mp157c.dtsi | 9 +++++++++
arch/arm/configs/multi_v7_defconfig | 1 +
3 files changed, 14 insertions(+)
--
2.7.4
^ permalink raw reply
* [PATCH v3 4/4] rtc: stm32: add stm32mp1 rtc support
From: Amelie Delaunay @ 2018-05-17 12:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558666-24243-1-git-send-email-amelie.delaunay@st.com>
This patch adds support for stm32mp1 RTC.
Some common registers with previous RTC version have a different offset.
It is the case for Control Register (CR) and ALaRMA Register (ALRMAR).
There are also new registers regarding event flags: now, Alarm event flag
is in Status Register (SR) and write 1 in Status Clear Register (SCR) is
required to clear the event.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
drivers/rtc/rtc-stm32.c | 103 +++++++++++++++++++++++++++++++++++++++++-------
1 file changed, 89 insertions(+), 14 deletions(-)
diff --git a/drivers/rtc/rtc-stm32.c b/drivers/rtc/rtc-stm32.c
index 8254e38..c5908cf 100644
--- a/drivers/rtc/rtc-stm32.c
+++ b/drivers/rtc/rtc-stm32.c
@@ -11,6 +11,7 @@
#include <linux/mfd/syscon.h>
#include <linux/module.h>
#include <linux/of_device.h>
+#include <linux/pm_wakeirq.h>
#include <linux/regmap.h>
#include <linux/rtc.h>
@@ -39,7 +40,7 @@
#define STM32_RTC_CR_ALRAE BIT(8)
#define STM32_RTC_CR_ALRAIE BIT(12)
-/* STM32_RTC_ISR bit fields */
+/* STM32_RTC_ISR/STM32_RTC_ICSR bit fields */
#define STM32_RTC_ISR_ALRAWF BIT(0)
#define STM32_RTC_ISR_INITS BIT(4)
#define STM32_RTC_ISR_RSF BIT(5)
@@ -71,21 +72,36 @@
#define STM32_RTC_ALRMXR_WDAY GENMASK(27, 24)
#define STM32_RTC_ALRMXR_DATE_MASK BIT(31)
+/* STM32_RTC_SR/_SCR bit fields */
+#define STM32_RTC_SR_ALRA BIT(0)
+
+/* STM32_RTC_VERR bit fields */
+#define STM32_RTC_VERR_MINREV_SHIFT 0
+#define STM32_RTC_VERR_MINREV GENMASK(3, 0)
+#define STM32_RTC_VERR_MAJREV_SHIFT 4
+#define STM32_RTC_VERR_MAJREV GENMASK(7, 4)
+
/* STM32_RTC_WPR key constants */
#define RTC_WPR_1ST_KEY 0xCA
#define RTC_WPR_2ND_KEY 0x53
#define RTC_WPR_WRONG_KEY 0xFF
+/* Max STM32 RTC register offset is 0x3FC */
+#define UNDEF_REG 0xFFFF
+
struct stm32_rtc;
struct stm32_rtc_registers {
- u8 tr;
- u8 dr;
- u8 cr;
- u8 isr;
- u8 prer;
- u8 alrmar;
- u8 wpr;
+ u16 tr;
+ u16 dr;
+ u16 cr;
+ u16 isr;
+ u16 prer;
+ u16 alrmar;
+ u16 wpr;
+ u16 sr;
+ u16 scr;
+ u16 verr;
};
struct stm32_rtc_events {
@@ -98,6 +114,7 @@ struct stm32_rtc_data {
void (*clear_events)(struct stm32_rtc *rtc, unsigned int flags);
bool has_pclk;
bool need_dbp;
+ bool has_wakeirq;
};
struct stm32_rtc {
@@ -110,6 +127,7 @@ struct stm32_rtc {
struct clk *rtc_ck;
const struct stm32_rtc_data *data;
int irq_alarm;
+ int wakeirq_alarm;
};
static void stm32_rtc_wpr_unlock(struct stm32_rtc *rtc)
@@ -193,7 +211,7 @@ static irqreturn_t stm32_rtc_alarm_irq(int irq, void *dev_id)
mutex_lock(&rtc->rtc_dev->ops_lock);
- status = readl_relaxed(rtc->base + regs->isr);
+ status = readl_relaxed(rtc->base + regs->sr);
cr = readl_relaxed(rtc->base + regs->cr);
if ((status & evts->alra) &&
@@ -325,7 +343,7 @@ static int stm32_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
alrmar = readl_relaxed(rtc->base + regs->alrmar);
cr = readl_relaxed(rtc->base + regs->cr);
- status = readl_relaxed(rtc->base + regs->isr);
+ status = readl_relaxed(rtc->base + regs->sr);
if (alrmar & STM32_RTC_ALRMXR_DATE_MASK) {
/*
@@ -533,6 +551,7 @@ static void stm32_rtc_clear_events(struct stm32_rtc *rtc,
static const struct stm32_rtc_data stm32_rtc_data = {
.has_pclk = false,
.need_dbp = true,
+ .has_wakeirq = false,
.regs = {
.tr = 0x00,
.dr = 0x04,
@@ -541,6 +560,9 @@ static const struct stm32_rtc_data stm32_rtc_data = {
.prer = 0x10,
.alrmar = 0x1C,
.wpr = 0x24,
+ .sr = 0x0C, /* set to ISR offset to ease alarm management */
+ .scr = UNDEF_REG,
+ .verr = UNDEF_REG,
},
.events = {
.alra = STM32_RTC_ISR_ALRAF,
@@ -551,6 +573,7 @@ static const struct stm32_rtc_data stm32_rtc_data = {
static const struct stm32_rtc_data stm32h7_rtc_data = {
.has_pclk = true,
.need_dbp = true,
+ .has_wakeirq = false,
.regs = {
.tr = 0x00,
.dr = 0x04,
@@ -559,6 +582,9 @@ static const struct stm32_rtc_data stm32h7_rtc_data = {
.prer = 0x10,
.alrmar = 0x1C,
.wpr = 0x24,
+ .sr = 0x0C, /* set to ISR offset to ease alarm management */
+ .scr = UNDEF_REG,
+ .verr = UNDEF_REG,
},
.events = {
.alra = STM32_RTC_ISR_ALRAF,
@@ -566,9 +592,41 @@ static const struct stm32_rtc_data stm32h7_rtc_data = {
.clear_events = stm32_rtc_clear_events,
};
+static void stm32mp1_rtc_clear_events(struct stm32_rtc *rtc,
+ unsigned int flags)
+{
+ struct stm32_rtc_registers regs = rtc->data->regs;
+
+ /* Flags are cleared by writing 1 in RTC_SCR */
+ writel_relaxed(flags, rtc->base + regs.scr);
+}
+
+static const struct stm32_rtc_data stm32mp1_data = {
+ .has_pclk = true,
+ .need_dbp = false,
+ .has_wakeirq = true,
+ .regs = {
+ .tr = 0x00,
+ .dr = 0x04,
+ .cr = 0x18,
+ .isr = 0x0C, /* named RTC_ICSR on stm32mp1 */
+ .prer = 0x10,
+ .alrmar = 0x40,
+ .wpr = 0x24,
+ .sr = 0x50,
+ .scr = 0x5C,
+ .verr = 0x3F4,
+ },
+ .events = {
+ .alra = STM32_RTC_SR_ALRA,
+ },
+ .clear_events = stm32mp1_rtc_clear_events,
+};
+
static const struct of_device_id stm32_rtc_of_match[] = {
{ .compatible = "st,stm32-rtc", .data = &stm32_rtc_data },
{ .compatible = "st,stm32h7-rtc", .data = &stm32h7_rtc_data },
+ { .compatible = "st,stm32mp1-rtc", .data = &stm32mp1_data },
{}
};
MODULE_DEVICE_TABLE(of, stm32_rtc_of_match);
@@ -727,12 +785,19 @@ static int stm32_rtc_probe(struct platform_device *pdev)
goto err;
}
- platform_set_drvdata(pdev, rtc);
-
ret = device_init_wakeup(&pdev->dev, true);
+ if (rtc->data->has_wakeirq) {
+ rtc->wakeirq_alarm = platform_get_irq(pdev, 1);
+ if (rtc->wakeirq_alarm <= 0)
+ ret = rtc->wakeirq_alarm;
+ else
+ ret = dev_pm_set_dedicated_wake_irq(&pdev->dev,
+ rtc->wakeirq_alarm);
+ }
if (ret)
- dev_warn(&pdev->dev,
- "alarm won't be able to wake up the system");
+ dev_warn(&pdev->dev, "alarm can't wake up the system: %d", ret);
+
+ platform_set_drvdata(pdev, rtc);
rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, pdev->name,
&stm32_rtc_ops, THIS_MODULE);
@@ -760,6 +825,14 @@ static int stm32_rtc_probe(struct platform_device *pdev)
if (!(readl_relaxed(rtc->base + regs->isr) & STM32_RTC_ISR_INITS))
dev_warn(&pdev->dev, "Date/Time must be initialized\n");
+ if (regs->verr != UNDEF_REG) {
+ u32 ver = readl_relaxed(rtc->base + regs->verr);
+
+ dev_info(&pdev->dev, "registered rev:%d.%d\n",
+ (ver >> STM32_RTC_VERR_MAJREV_SHIFT) & 0xF,
+ (ver >> STM32_RTC_VERR_MINREV_SHIFT) & 0xF);
+ }
+
return 0;
err:
if (rtc->data->has_pclk)
@@ -769,6 +842,7 @@ static int stm32_rtc_probe(struct platform_device *pdev)
if (rtc->data->need_dbp)
regmap_update_bits(rtc->dbp, rtc->dbp_reg, rtc->dbp_mask, 0);
+ dev_pm_clear_wake_irq(&pdev->dev);
device_init_wakeup(&pdev->dev, false);
return ret;
@@ -795,6 +869,7 @@ static int stm32_rtc_remove(struct platform_device *pdev)
if (rtc->data->need_dbp)
regmap_update_bits(rtc->dbp, rtc->dbp_reg, rtc->dbp_mask, 0);
+ dev_pm_clear_wake_irq(&pdev->dev);
device_init_wakeup(&pdev->dev, false);
return 0;
--
2.7.4
^ permalink raw reply related
* [PATCH v3 3/4] dt-bindings: rtc: update stm32-rtc documentation for stm32mp1 rtc
From: Amelie Delaunay @ 2018-05-17 12:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558666-24243-1-git-send-email-amelie.delaunay@st.com>
RTC embedded in stm32mp1 SoC is slightly different from stm32h7 one, it
doesn't require to disable backup domain write protection, and rtc_ck
parent clock assignment isn't allowed.
To sum up, stm32mp1 RTC requires 2 clocks, pclk and rtc_ck, and an RTC
alarm interrupt.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
.../devicetree/bindings/rtc/st,stm32-rtc.txt | 27 ++++++++++++++++------
1 file changed, 20 insertions(+), 7 deletions(-)
diff --git a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt
index 00f8b5d..c920e27 100644
--- a/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt
+++ b/Documentation/devicetree/bindings/rtc/st,stm32-rtc.txt
@@ -1,25 +1,29 @@
STM32 Real Time Clock
Required properties:
-- compatible: can be either "st,stm32-rtc" or "st,stm32h7-rtc", depending on
- the device is compatible with stm32(f4/f7) or stm32h7.
+- compatible: can be one of the following:
+ - "st,stm32-rtc" for devices compatible with stm32(f4/f7).
+ - "st,stm32h7-rtc" for devices compatible with stm32h7.
+ - "st,stm32mp1-rtc" for devices compatible with stm32mp1.
- reg: address range of rtc register set.
- clocks: can use up to two clocks, depending on part used:
- "rtc_ck": RTC clock source.
- It is required on stm32(f4/f7) and stm32h7.
- "pclk": RTC APB interface clock.
It is not present on stm32(f4/f7).
- It is required on stm32h7.
+ It is required on stm32(h7/mp1).
- clock-names: must be "rtc_ck" and "pclk".
- It is required only on stm32h7.
+ It is required on stm32(h7/mp1).
- interrupt-parent: phandle for the interrupt controller.
-- interrupts: rtc alarm interrupt.
+ It is required on stm32(f4/f7/h7).
+- interrupts: rtc alarm interrupt. On stm32mp1, a second interrupt is required
+ for rtc alarm wakeup interrupt.
- st,syscfg: phandle/offset/mask triplet. The phandle to pwrcfg used to
access control register at offset, and change the dbp (Disable Backup
Protection) bit represented by the mask, mandatory to disable/enable backup
domain (RTC registers) write protection.
+ It is required on stm32(f4/f7/h7).
-Optional properties (to override default rtc_ck parent clock):
+Optional properties (to override default rtc_ck parent clock on stm32(f4/f7/h7):
- assigned-clocks: reference to the rtc_ck clock entry.
- assigned-clock-parents: phandle of the new parent clock of rtc_ck.
@@ -48,3 +52,12 @@ Example:
interrupt-names = "alarm";
st,syscfg = <&pwrcfg 0x00 0x100>;
};
+
+ rtc: rtc at 5c004000 {
+ compatible = "st,stm32mp1-rtc";
+ reg = <0x5c004000 0x400>;
+ clocks = <&rcc RTCAPB>, <&rcc RTC>;
+ clock-names = "pclk", "rtc_ck";
+ interrupts-extended = <&intc GIC_SPI 3 IRQ_TYPE_NONE>,
+ <&exti 19 1>;
+ };
--
2.7.4
^ permalink raw reply related
* [PATCH v3 2/4] rtc: stm32: rework register management to prepare other version of RTC
From: Amelie Delaunay @ 2018-05-17 12:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558666-24243-1-git-send-email-amelie.delaunay@st.com>
This patch reworks register/bits management because next version of RTC
uses the same way of working but with different register's offset or bits
moved in new registers.
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
drivers/rtc/rtc-stm32.c | 184 +++++++++++++++++++++++++++++++++---------------
1 file changed, 127 insertions(+), 57 deletions(-)
diff --git a/drivers/rtc/rtc-stm32.c b/drivers/rtc/rtc-stm32.c
index d41f804..8254e38 100644
--- a/drivers/rtc/rtc-stm32.c
+++ b/drivers/rtc/rtc-stm32.c
@@ -16,15 +16,6 @@
#define DRIVER_NAME "stm32_rtc"
-/* STM32 RTC registers */
-#define STM32_RTC_TR 0x00
-#define STM32_RTC_DR 0x04
-#define STM32_RTC_CR 0x08
-#define STM32_RTC_ISR 0x0C
-#define STM32_RTC_PRER 0x10
-#define STM32_RTC_ALRMAR 0x1C
-#define STM32_RTC_WPR 0x24
-
/* STM32_RTC_TR bit fields */
#define STM32_RTC_TR_SEC_SHIFT 0
#define STM32_RTC_TR_SEC GENMASK(6, 0)
@@ -85,7 +76,26 @@
#define RTC_WPR_2ND_KEY 0x53
#define RTC_WPR_WRONG_KEY 0xFF
+struct stm32_rtc;
+
+struct stm32_rtc_registers {
+ u8 tr;
+ u8 dr;
+ u8 cr;
+ u8 isr;
+ u8 prer;
+ u8 alrmar;
+ u8 wpr;
+};
+
+struct stm32_rtc_events {
+ u32 alra;
+};
+
struct stm32_rtc_data {
+ const struct stm32_rtc_registers regs;
+ const struct stm32_rtc_events events;
+ void (*clear_events)(struct stm32_rtc *rtc, unsigned int flags);
bool has_pclk;
bool need_dbp;
};
@@ -96,30 +106,35 @@ struct stm32_rtc {
struct regmap *dbp;
unsigned int dbp_reg;
unsigned int dbp_mask;
- struct stm32_rtc_data *data;
struct clk *pclk;
struct clk *rtc_ck;
+ const struct stm32_rtc_data *data;
int irq_alarm;
};
static void stm32_rtc_wpr_unlock(struct stm32_rtc *rtc)
{
- writel_relaxed(RTC_WPR_1ST_KEY, rtc->base + STM32_RTC_WPR);
- writel_relaxed(RTC_WPR_2ND_KEY, rtc->base + STM32_RTC_WPR);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+
+ writel_relaxed(RTC_WPR_1ST_KEY, rtc->base + regs->wpr);
+ writel_relaxed(RTC_WPR_2ND_KEY, rtc->base + regs->wpr);
}
static void stm32_rtc_wpr_lock(struct stm32_rtc *rtc)
{
- writel_relaxed(RTC_WPR_WRONG_KEY, rtc->base + STM32_RTC_WPR);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+
+ writel_relaxed(RTC_WPR_WRONG_KEY, rtc->base + regs->wpr);
}
static int stm32_rtc_enter_init_mode(struct stm32_rtc *rtc)
{
- unsigned int isr = readl_relaxed(rtc->base + STM32_RTC_ISR);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+ unsigned int isr = readl_relaxed(rtc->base + regs->isr);
if (!(isr & STM32_RTC_ISR_INITF)) {
isr |= STM32_RTC_ISR_INIT;
- writel_relaxed(isr, rtc->base + STM32_RTC_ISR);
+ writel_relaxed(isr, rtc->base + regs->isr);
/*
* It takes around 2 rtc_ck clock cycles to enter in
@@ -128,7 +143,7 @@ static int stm32_rtc_enter_init_mode(struct stm32_rtc *rtc)
* 1MHz, we poll every 10 us with a timeout of 100ms.
*/
return readl_relaxed_poll_timeout_atomic(
- rtc->base + STM32_RTC_ISR,
+ rtc->base + regs->isr,
isr, (isr & STM32_RTC_ISR_INITF),
10, 100000);
}
@@ -138,40 +153,50 @@ static int stm32_rtc_enter_init_mode(struct stm32_rtc *rtc)
static void stm32_rtc_exit_init_mode(struct stm32_rtc *rtc)
{
- unsigned int isr = readl_relaxed(rtc->base + STM32_RTC_ISR);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+ unsigned int isr = readl_relaxed(rtc->base + regs->isr);
isr &= ~STM32_RTC_ISR_INIT;
- writel_relaxed(isr, rtc->base + STM32_RTC_ISR);
+ writel_relaxed(isr, rtc->base + regs->isr);
}
static int stm32_rtc_wait_sync(struct stm32_rtc *rtc)
{
- unsigned int isr = readl_relaxed(rtc->base + STM32_RTC_ISR);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+ unsigned int isr = readl_relaxed(rtc->base + regs->isr);
isr &= ~STM32_RTC_ISR_RSF;
- writel_relaxed(isr, rtc->base + STM32_RTC_ISR);
+ writel_relaxed(isr, rtc->base + regs->isr);
/*
* Wait for RSF to be set to ensure the calendar registers are
* synchronised, it takes around 2 rtc_ck clock cycles
*/
- return readl_relaxed_poll_timeout_atomic(rtc->base + STM32_RTC_ISR,
+ return readl_relaxed_poll_timeout_atomic(rtc->base + regs->isr,
isr,
(isr & STM32_RTC_ISR_RSF),
10, 100000);
}
+static void stm32_rtc_clear_event_flags(struct stm32_rtc *rtc,
+ unsigned int flags)
+{
+ rtc->data->clear_events(rtc, flags);
+}
+
static irqreturn_t stm32_rtc_alarm_irq(int irq, void *dev_id)
{
struct stm32_rtc *rtc = (struct stm32_rtc *)dev_id;
- unsigned int isr, cr;
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+ const struct stm32_rtc_events *evts = &rtc->data->events;
+ unsigned int status, cr;
mutex_lock(&rtc->rtc_dev->ops_lock);
- isr = readl_relaxed(rtc->base + STM32_RTC_ISR);
- cr = readl_relaxed(rtc->base + STM32_RTC_CR);
+ status = readl_relaxed(rtc->base + regs->isr);
+ cr = readl_relaxed(rtc->base + regs->cr);
- if ((isr & STM32_RTC_ISR_ALRAF) &&
+ if ((status & evts->alra) &&
(cr & STM32_RTC_CR_ALRAIE)) {
/* Alarm A flag - Alarm interrupt */
dev_dbg(&rtc->rtc_dev->dev, "Alarm occurred\n");
@@ -179,9 +204,8 @@ static irqreturn_t stm32_rtc_alarm_irq(int irq, void *dev_id)
/* Pass event to the kernel */
rtc_update_irq(rtc->rtc_dev, 1, RTC_IRQF | RTC_AF);
- /* Clear event flag, otherwise new events won't be received */
- writel_relaxed(isr & ~STM32_RTC_ISR_ALRAF,
- rtc->base + STM32_RTC_ISR);
+ /* Clear event flags, otherwise new events won't be received */
+ stm32_rtc_clear_event_flags(rtc, evts->alra);
}
mutex_unlock(&rtc->rtc_dev->ops_lock);
@@ -228,11 +252,12 @@ static void bcd2tm(struct rtc_time *tm)
static int stm32_rtc_read_time(struct device *dev, struct rtc_time *tm)
{
struct stm32_rtc *rtc = dev_get_drvdata(dev);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
unsigned int tr, dr;
/* Time and Date in BCD format */
- tr = readl_relaxed(rtc->base + STM32_RTC_TR);
- dr = readl_relaxed(rtc->base + STM32_RTC_DR);
+ tr = readl_relaxed(rtc->base + regs->tr);
+ dr = readl_relaxed(rtc->base + regs->dr);
tm->tm_sec = (tr & STM32_RTC_TR_SEC) >> STM32_RTC_TR_SEC_SHIFT;
tm->tm_min = (tr & STM32_RTC_TR_MIN) >> STM32_RTC_TR_MIN_SHIFT;
@@ -253,6 +278,7 @@ static int stm32_rtc_read_time(struct device *dev, struct rtc_time *tm)
static int stm32_rtc_set_time(struct device *dev, struct rtc_time *tm)
{
struct stm32_rtc *rtc = dev_get_drvdata(dev);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
unsigned int tr, dr;
int ret = 0;
@@ -277,8 +303,8 @@ static int stm32_rtc_set_time(struct device *dev, struct rtc_time *tm)
goto end;
}
- writel_relaxed(tr, rtc->base + STM32_RTC_TR);
- writel_relaxed(dr, rtc->base + STM32_RTC_DR);
+ writel_relaxed(tr, rtc->base + regs->tr);
+ writel_relaxed(dr, rtc->base + regs->dr);
stm32_rtc_exit_init_mode(rtc);
@@ -292,12 +318,14 @@ static int stm32_rtc_set_time(struct device *dev, struct rtc_time *tm)
static int stm32_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
{
struct stm32_rtc *rtc = dev_get_drvdata(dev);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+ const struct stm32_rtc_events *evts = &rtc->data->events;
struct rtc_time *tm = &alrm->time;
- unsigned int alrmar, cr, isr;
+ unsigned int alrmar, cr, status;
- alrmar = readl_relaxed(rtc->base + STM32_RTC_ALRMAR);
- cr = readl_relaxed(rtc->base + STM32_RTC_CR);
- isr = readl_relaxed(rtc->base + STM32_RTC_ISR);
+ alrmar = readl_relaxed(rtc->base + regs->alrmar);
+ cr = readl_relaxed(rtc->base + regs->cr);
+ status = readl_relaxed(rtc->base + regs->isr);
if (alrmar & STM32_RTC_ALRMXR_DATE_MASK) {
/*
@@ -350,7 +378,7 @@ static int stm32_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
bcd2tm(tm);
alrm->enabled = (cr & STM32_RTC_CR_ALRAE) ? 1 : 0;
- alrm->pending = (isr & STM32_RTC_ISR_ALRAF) ? 1 : 0;
+ alrm->pending = (status & evts->alra) ? 1 : 0;
return 0;
}
@@ -358,9 +386,11 @@ static int stm32_rtc_read_alarm(struct device *dev, struct rtc_wkalrm *alrm)
static int stm32_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
{
struct stm32_rtc *rtc = dev_get_drvdata(dev);
- unsigned int isr, cr;
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+ const struct stm32_rtc_events *evts = &rtc->data->events;
+ unsigned int cr;
- cr = readl_relaxed(rtc->base + STM32_RTC_CR);
+ cr = readl_relaxed(rtc->base + regs->cr);
stm32_rtc_wpr_unlock(rtc);
@@ -369,12 +399,10 @@ static int stm32_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
cr |= (STM32_RTC_CR_ALRAIE | STM32_RTC_CR_ALRAE);
else
cr &= ~(STM32_RTC_CR_ALRAIE | STM32_RTC_CR_ALRAE);
- writel_relaxed(cr, rtc->base + STM32_RTC_CR);
+ writel_relaxed(cr, rtc->base + regs->cr);
- /* Clear event flag, otherwise new events won't be received */
- isr = readl_relaxed(rtc->base + STM32_RTC_ISR);
- isr &= ~STM32_RTC_ISR_ALRAF;
- writel_relaxed(isr, rtc->base + STM32_RTC_ISR);
+ /* Clear event flags, otherwise new events won't be received */
+ stm32_rtc_clear_event_flags(rtc, evts->alra);
stm32_rtc_wpr_lock(rtc);
@@ -383,9 +411,10 @@ static int stm32_rtc_alarm_irq_enable(struct device *dev, unsigned int enabled)
static int stm32_rtc_valid_alrm(struct stm32_rtc *rtc, struct rtc_time *tm)
{
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
int cur_day, cur_mon, cur_year, cur_hour, cur_min, cur_sec;
- unsigned int dr = readl_relaxed(rtc->base + STM32_RTC_DR);
- unsigned int tr = readl_relaxed(rtc->base + STM32_RTC_TR);
+ unsigned int dr = readl_relaxed(rtc->base + regs->dr);
+ unsigned int tr = readl_relaxed(rtc->base + regs->tr);
cur_day = (dr & STM32_RTC_DR_DATE) >> STM32_RTC_DR_DATE_SHIFT;
cur_mon = (dr & STM32_RTC_DR_MONTH) >> STM32_RTC_DR_MONTH_SHIFT;
@@ -419,6 +448,7 @@ static int stm32_rtc_valid_alrm(struct stm32_rtc *rtc, struct rtc_time *tm)
static int stm32_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
{
struct stm32_rtc *rtc = dev_get_drvdata(dev);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
struct rtc_time *tm = &alrm->time;
unsigned int cr, isr, alrmar;
int ret = 0;
@@ -450,15 +480,15 @@ static int stm32_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
stm32_rtc_wpr_unlock(rtc);
/* Disable Alarm */
- cr = readl_relaxed(rtc->base + STM32_RTC_CR);
+ cr = readl_relaxed(rtc->base + regs->cr);
cr &= ~STM32_RTC_CR_ALRAE;
- writel_relaxed(cr, rtc->base + STM32_RTC_CR);
+ writel_relaxed(cr, rtc->base + regs->cr);
/*
* Poll Alarm write flag to be sure that Alarm update is allowed: it
* takes around 2 rtc_ck clock cycles
*/
- ret = readl_relaxed_poll_timeout_atomic(rtc->base + STM32_RTC_ISR,
+ ret = readl_relaxed_poll_timeout_atomic(rtc->base + regs->isr,
isr,
(isr & STM32_RTC_ISR_ALRAWF),
10, 100000);
@@ -469,7 +499,7 @@ static int stm32_rtc_set_alarm(struct device *dev, struct rtc_wkalrm *alrm)
}
/* Write to Alarm register */
- writel_relaxed(alrmar, rtc->base + STM32_RTC_ALRMAR);
+ writel_relaxed(alrmar, rtc->base + regs->alrmar);
if (alrm->enabled)
stm32_rtc_alarm_irq_enable(dev, 1);
@@ -490,14 +520,50 @@ static const struct rtc_class_ops stm32_rtc_ops = {
.alarm_irq_enable = stm32_rtc_alarm_irq_enable,
};
+static void stm32_rtc_clear_events(struct stm32_rtc *rtc,
+ unsigned int flags)
+{
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
+
+ /* Flags are cleared by writing 0 in RTC_ISR */
+ writel_relaxed(readl_relaxed(rtc->base + regs->isr) & ~flags,
+ rtc->base + regs->isr);
+}
+
static const struct stm32_rtc_data stm32_rtc_data = {
.has_pclk = false,
.need_dbp = true,
+ .regs = {
+ .tr = 0x00,
+ .dr = 0x04,
+ .cr = 0x08,
+ .isr = 0x0C,
+ .prer = 0x10,
+ .alrmar = 0x1C,
+ .wpr = 0x24,
+ },
+ .events = {
+ .alra = STM32_RTC_ISR_ALRAF,
+ },
+ .clear_events = stm32_rtc_clear_events,
};
static const struct stm32_rtc_data stm32h7_rtc_data = {
.has_pclk = true,
.need_dbp = true,
+ .regs = {
+ .tr = 0x00,
+ .dr = 0x04,
+ .cr = 0x08,
+ .isr = 0x0C,
+ .prer = 0x10,
+ .alrmar = 0x1C,
+ .wpr = 0x24,
+ },
+ .events = {
+ .alra = STM32_RTC_ISR_ALRAF,
+ },
+ .clear_events = stm32_rtc_clear_events,
};
static const struct of_device_id stm32_rtc_of_match[] = {
@@ -510,6 +576,7 @@ MODULE_DEVICE_TABLE(of, stm32_rtc_of_match);
static int stm32_rtc_init(struct platform_device *pdev,
struct stm32_rtc *rtc)
{
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
unsigned int prer, pred_a, pred_s, pred_a_max, pred_s_max, cr;
unsigned int rate;
int ret = 0;
@@ -550,14 +617,14 @@ static int stm32_rtc_init(struct platform_device *pdev,
}
prer = (pred_s << STM32_RTC_PRER_PRED_S_SHIFT) & STM32_RTC_PRER_PRED_S;
- writel_relaxed(prer, rtc->base + STM32_RTC_PRER);
+ writel_relaxed(prer, rtc->base + regs->prer);
prer |= (pred_a << STM32_RTC_PRER_PRED_A_SHIFT) & STM32_RTC_PRER_PRED_A;
- writel_relaxed(prer, rtc->base + STM32_RTC_PRER);
+ writel_relaxed(prer, rtc->base + regs->prer);
/* Force 24h time format */
- cr = readl_relaxed(rtc->base + STM32_RTC_CR);
+ cr = readl_relaxed(rtc->base + regs->cr);
cr &= ~STM32_RTC_CR_FMT;
- writel_relaxed(cr, rtc->base + STM32_RTC_CR);
+ writel_relaxed(cr, rtc->base + regs->cr);
stm32_rtc_exit_init_mode(rtc);
@@ -571,6 +638,7 @@ static int stm32_rtc_init(struct platform_device *pdev,
static int stm32_rtc_probe(struct platform_device *pdev)
{
struct stm32_rtc *rtc;
+ const struct stm32_rtc_registers *regs;
struct resource *res;
int ret;
@@ -585,6 +653,7 @@ static int stm32_rtc_probe(struct platform_device *pdev)
rtc->data = (struct stm32_rtc_data *)
of_device_get_match_data(&pdev->dev);
+ regs = &rtc->data->regs;
if (rtc->data->need_dbp) {
rtc->dbp = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
@@ -688,7 +757,7 @@ static int stm32_rtc_probe(struct platform_device *pdev)
* If INITS flag is reset (calendar year field set to 0x00), calendar
* must be initialized
*/
- if (!(readl_relaxed(rtc->base + STM32_RTC_ISR) & STM32_RTC_ISR_INITS))
+ if (!(readl_relaxed(rtc->base + regs->isr) & STM32_RTC_ISR_INITS))
dev_warn(&pdev->dev, "Date/Time must be initialized\n");
return 0;
@@ -708,13 +777,14 @@ static int stm32_rtc_probe(struct platform_device *pdev)
static int stm32_rtc_remove(struct platform_device *pdev)
{
struct stm32_rtc *rtc = platform_get_drvdata(pdev);
+ const struct stm32_rtc_registers *regs = &rtc->data->regs;
unsigned int cr;
/* Disable interrupts */
stm32_rtc_wpr_unlock(rtc);
- cr = readl_relaxed(rtc->base + STM32_RTC_CR);
+ cr = readl_relaxed(rtc->base + regs->cr);
cr &= ~STM32_RTC_CR_ALRAIE;
- writel_relaxed(cr, rtc->base + STM32_RTC_CR);
+ writel_relaxed(cr, rtc->base + regs->cr);
stm32_rtc_wpr_lock(rtc);
clk_disable_unprepare(rtc->rtc_ck);
--
2.7.4
^ permalink raw reply related
* [PATCH v3 1/4] rtc: stm32: fix misspelling and misalignment issues
From: Amelie Delaunay @ 2018-05-17 12:04 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526558666-24243-1-git-send-email-amelie.delaunay@st.com>
This patch cleans the following checkpatch complaints:
CHECK: 'initalized' may be misspelled - perhaps 'initialized'?
#644: FILE: drivers/rtc/rtc-stm32.c:644:
+ * the calendar has been initalized or not. INITS flag is reset by a
CHECK: Alignment should match open parenthesis
#669: FILE: drivers/rtc/rtc-stm32.c:669:
+ rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, pdev->name,
+ &stm32_rtc_ops, THIS_MODULE);
Signed-off-by: Amelie Delaunay <amelie.delaunay@st.com>
---
drivers/rtc/rtc-stm32.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/rtc/rtc-stm32.c b/drivers/rtc/rtc-stm32.c
index de49b5b..d41f804 100644
--- a/drivers/rtc/rtc-stm32.c
+++ b/drivers/rtc/rtc-stm32.c
@@ -641,7 +641,7 @@ static int stm32_rtc_probe(struct platform_device *pdev)
/*
* After a system reset, RTC_ISR.INITS flag can be read to check if
- * the calendar has been initalized or not. INITS flag is reset by a
+ * the calendar has been initialized or not. INITS flag is reset by a
* power-on reset (no vbat, no power-supply). It is not reset if
* rtc_ck parent clock has changed (so RTC prescalers need to be
* changed). That's why we cannot rely on this flag to know if RTC
@@ -666,7 +666,7 @@ static int stm32_rtc_probe(struct platform_device *pdev)
"alarm won't be able to wake up the system");
rtc->rtc_dev = devm_rtc_device_register(&pdev->dev, pdev->name,
- &stm32_rtc_ops, THIS_MODULE);
+ &stm32_rtc_ops, THIS_MODULE);
if (IS_ERR(rtc->rtc_dev)) {
ret = PTR_ERR(rtc->rtc_dev);
dev_err(&pdev->dev, "rtc device registration failed, err=%d\n",
--
2.7.4
^ permalink raw reply related
* [PATCH v3 0/4] Introduce STM32MP1 RTC
From: Amelie Delaunay @ 2018-05-17 12:04 UTC (permalink / raw)
To: linux-arm-kernel
This series introduces STM32MP1 RTC.
On STM32MP1:
- two clocks are needed, plck and rtc_ck;
- to wakeup the system, a wakeup alarm interrupt is needed;
- some registers or bits have moved, but the operation is the same;
- the Backup Domain Protection (DBP) is not managed by RTC driver.
---
Changes in v3:
* Move cleanup changes in a separate patch
* Replace regs and evts by pointers to ensure no copy is made
* Set all registers offset as u16 instead of u8 and u16
* Fix Kbuild smatch warning:
drivers/rtc/rtc-stm32.c:827 stm32_rtc_probe()
warn: always true condition '(regs.verr != ~0) => (0-u16max != (-1))'
Changes in v2:
* One compatible per line in bindings file
* Remove unnecessary comment under rtc_ck as this clock is required for all
* Remove interrupts-extended and add stm32mp1 rtc alarm wakeup interrupt in
interrupts property description
Amelie Delaunay (4):
rtc: stm32: fix misspelling and misalignment issues
rtc: stm32: rework register management to prepare other version of RTC
dt-bindings: rtc: update stm32-rtc documentation for stm32mp1 rtc
rtc: stm32: add stm32mp1 rtc support
.../devicetree/bindings/rtc/st,stm32-rtc.txt | 27 +-
drivers/rtc/rtc-stm32.c | 273 ++++++++++++++++-----
2 files changed, 229 insertions(+), 71 deletions(-)
--
2.7.4
^ permalink raw reply
* [PATCH 1/2] clk: imx7d: correct enet clock CCGR register offset
From: Stefan Agner @ 2018-05-17 11:22 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526546422-7431-1-git-send-email-Anson.Huang@nxp.com>
On 17.05.2018 10:40, Anson Huang wrote:
> Correct enet clock CCGR register offset.
>
> CCGR6: IMX7D_ENET_AXI_ROOT_CLK (enet1 and enet2 bus clocks)
> CCGR112: IMX7D_ENET1_TIME_ROOT_CLK, IMX7D_ENET1_IPG_ROOT_CLK
> CCGR113: IMX7D_ENET2_TIME_ROOT_CLK, IMX7D_ENET2_IPG_ROOT_CLK
>
> IMX7D_ENET_PHY_REF_ROOT_DIV supplies clock for PHY,
> no gate after this clock, its parent clock root has gate.
> IMX7D_ENET1_REF_ROOT_DIV/IMX7D_ENET2_REF_ROOT_DIV supplies clocks
> for enet IPG_CLK_RMII, no gate after the clock, its parent
> clock root has gate.
>
> IMX7D_PLL_ENET_MAIN_125M_CLK (anatop pll) supplies clock for
> enet RGMII tx_clk.
As far as I can tell there are two changes here in one patch:
1. The non existing IMX7D_ENET_PHY_REF_ROOT_CLK gate is removed
2. Shared clock gate for the enet time/ipg clock is taken into account.
I would rather prefer to have separate patches. The device tree change
also does two things, so this would lead to 4 patches total.
We can avoid the device tree change for the PHY clk and even maintain
backward compatibility for that part by renaming
IMX7D_ENET_PHY_REF_ROOT_DIV to IMX7D_ENET_PHY_REF_ROOT_CLK.
So this would end up with the following first patch to address the
PHY_ROOT clock issue:
--- a/drivers/clk/imx/clk-imx7d.c
+++ b/drivers/clk/imx/clk-imx7d.c
@@ -738,7 +738,7 @@ static void __init imx7d_clocks_init(struct
device_node *ccm_node)
clks[IMX7D_ENET1_TIME_ROOT_DIV] =
imx_clk_divider2("enet1_time_post_div", "enet1_time_pre_div", base +
0xa780, 0, 6);
clks[IMX7D_ENET2_REF_ROOT_DIV] =
imx_clk_divider2("enet2_ref_post_div", "enet2_ref_pre_div", base +
0xa800, 0, 6);
clks[IMX7D_ENET2_TIME_ROOT_DIV] =
imx_clk_divider2("enet2_time_post_div", "enet2_time_pre_div", base +
0xa880, 0, 6);
- clks[IMX7D_ENET_PHY_REF_ROOT_DIV] =
imx_clk_divider2("enet_phy_ref_post_div", "enet_phy_ref_pre_div", base +
0xa900, 0, 6);
+ clks[IMX7D_ENET_PHY_REF_ROOT_CLK] =
imx_clk_divider2("enet_phy_ref_root_clk", "enet_phy_ref_pre_div", base +
0xa900, 0, 6);
clks[IMX7D_EIM_ROOT_DIV] = imx_clk_divider2("eim_post_div",
"eim_pre_div", base + 0xa980, 0, 6);
clks[IMX7D_NAND_ROOT_CLK] = imx_clk_divider2("nand_root_clk",
"nand_pre_div", base + 0xaa00, 0, 6);
clks[IMX7D_QSPI_ROOT_DIV] = imx_clk_divider2("qspi_post_div",
"qspi_pre_div", base + 0xaa80, 0, 6);
@@ -816,7 +816,6 @@ static void __init imx7d_clocks_init(struct
device_node *ccm_node)
clks[IMX7D_ENET1_TIME_ROOT_CLK] =
imx_clk_gate4("enet1_time_root_clk", "enet1_time_post_div", base +
0x44f0, 0);
clks[IMX7D_ENET2_REF_ROOT_CLK] =
imx_clk_gate4("enet2_ref_root_clk", "enet2_ref_post_div", base + 0x4500,
0);
clks[IMX7D_ENET2_TIME_ROOT_CLK] =
imx_clk_gate4("enet2_time_root_clk", "enet2_time_post_div", base +
0x4510, 0);
- clks[IMX7D_ENET_PHY_REF_ROOT_CLK] =
imx_clk_gate4("enet_phy_ref_root_clk", "enet_phy_ref_post_div", base +
0x4520, 0);
clks[IMX7D_EIM_ROOT_CLK] = imx_clk_gate4("eim_root_clk",
"eim_post_div", base + 0x4160, 0);
clks[IMX7D_NAND_RAWNAND_CLK] =
imx_clk_gate2_shared2("nand_rawnand_clk", "nand_root_clk", base +
0x4140, 0, &share_count_nand);
clks[IMX7D_NAND_USDHC_BUS_RAWNAND_CLK] =
imx_clk_gate2_shared2("nand_usdhc_rawnand_clk", "nand_usdhc_root_clk",
base + 0x4140, 0, &share_count_nand);
A second patch would then fix the clock gate issue and the third the
unavoidable device tree change for the ipg clock.
--
Stefan
>
> Based on Andy Duan's patch from the NXP kernel tree.
>
> Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
> ---
> drivers/clk/imx/clk-imx7d.c | 11 ++++++-----
> include/dt-bindings/clock/imx7d-clock.h | 4 +++-
> 2 files changed, 9 insertions(+), 6 deletions(-)
>
> diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
> index 975a20d..485ab49 100644
> --- a/drivers/clk/imx/clk-imx7d.c
> +++ b/drivers/clk/imx/clk-imx7d.c
> @@ -26,6 +26,8 @@ static u32 share_count_sai1;
> static u32 share_count_sai2;
> static u32 share_count_sai3;
> static u32 share_count_nand;
> +static u32 share_count_enet1;
> +static u32 share_count_enet2;
>
> static const struct clk_div_table test_div_table[] = {
> { .val = 3, .div = 1, },
> @@ -805,6 +807,10 @@ static void __init imx7d_clocks_init(struct
> device_node *ccm_node)
> clks[IMX7D_MIPI_DSI_ROOT_CLK] = imx_clk_gate4("mipi_dsi_root_clk",
> "mipi_dsi_post_div", base + 0x4650, 0);
> clks[IMX7D_MIPI_CSI_ROOT_CLK] = imx_clk_gate4("mipi_csi_root_clk",
> "mipi_csi_post_div", base + 0x4640, 0);
> clks[IMX7D_MIPI_DPHY_ROOT_CLK] = imx_clk_gate4("mipi_dphy_root_clk",
> "mipi_dphy_post_div", base + 0x4660, 0);
> + clks[IMX7D_ENET1_IPG_ROOT_CLK] =
> imx_clk_gate2_shared2("enet1_ipg_root_clk", "enet_axi_post_div", base
> + 0x4700, 0, &share_count_enet1);
> + clks[IMX7D_ENET1_TIME_ROOT_CLK] =
> imx_clk_gate2_shared2("enet1_time_root_clk", "enet1_time_post_div",
> base + 0x4700, 0, &share_count_enet1);
> + clks[IMX7D_ENET2_IPG_ROOT_CLK] =
> imx_clk_gate2_shared2("enet2_ipg_root_clk", "enet_axi_post_div", base
> + 0x4710, 0, &share_count_enet2);
> + clks[IMX7D_ENET2_TIME_ROOT_CLK] =
> imx_clk_gate2_shared2("enet2_time_root_clk", "enet2_time_post_div",
> base + 0x4710, 0, &share_count_enet2);
> clks[IMX7D_SAI1_ROOT_CLK] = imx_clk_gate2_shared2("sai1_root_clk",
> "sai1_post_div", base + 0x48c0, 0, &share_count_sai1);
> clks[IMX7D_SAI1_IPG_CLK] = imx_clk_gate2_shared2("sai1_ipg_clk",
> "ipg_root_clk", base + 0x48c0, 0, &share_count_sai1);
> clks[IMX7D_SAI2_ROOT_CLK] = imx_clk_gate2_shared2("sai2_root_clk",
> "sai2_post_div", base + 0x48d0, 0, &share_count_sai2);
> @@ -812,11 +818,6 @@ static void __init imx7d_clocks_init(struct
> device_node *ccm_node)
> clks[IMX7D_SAI3_ROOT_CLK] = imx_clk_gate2_shared2("sai3_root_clk",
> "sai3_post_div", base + 0x48e0, 0, &share_count_sai3);
> clks[IMX7D_SAI3_IPG_CLK] = imx_clk_gate2_shared2("sai3_ipg_clk",
> "ipg_root_clk", base + 0x48e0, 0, &share_count_sai3);
> clks[IMX7D_SPDIF_ROOT_CLK] = imx_clk_gate4("spdif_root_clk",
> "spdif_post_div", base + 0x44d0, 0);
> - clks[IMX7D_ENET1_REF_ROOT_CLK] = imx_clk_gate4("enet1_ref_root_clk",
> "enet1_ref_post_div", base + 0x44e0, 0);
> - clks[IMX7D_ENET1_TIME_ROOT_CLK] =
> imx_clk_gate4("enet1_time_root_clk", "enet1_time_post_div", base +
> 0x44f0, 0);
> - clks[IMX7D_ENET2_REF_ROOT_CLK] = imx_clk_gate4("enet2_ref_root_clk",
> "enet2_ref_post_div", base + 0x4500, 0);
> - clks[IMX7D_ENET2_TIME_ROOT_CLK] =
> imx_clk_gate4("enet2_time_root_clk", "enet2_time_post_div", base +
> 0x4510, 0);
> - clks[IMX7D_ENET_PHY_REF_ROOT_CLK] =
> imx_clk_gate4("enet_phy_ref_root_clk", "enet_phy_ref_post_div", base +
> 0x4520, 0);
> clks[IMX7D_EIM_ROOT_CLK] = imx_clk_gate4("eim_root_clk",
> "eim_post_div", base + 0x4160, 0);
> clks[IMX7D_NAND_RAWNAND_CLK] =
> imx_clk_gate2_shared2("nand_rawnand_clk", "nand_root_clk", base +
> 0x4140, 0, &share_count_nand);
> clks[IMX7D_NAND_USDHC_BUS_RAWNAND_CLK] =
> imx_clk_gate2_shared2("nand_usdhc_rawnand_clk", "nand_usdhc_root_clk",
> base + 0x4140, 0, &share_count_nand);
> diff --git a/include/dt-bindings/clock/imx7d-clock.h
> b/include/dt-bindings/clock/imx7d-clock.h
> index b2325d3e2..fef0647 100644
> --- a/include/dt-bindings/clock/imx7d-clock.h
> +++ b/include/dt-bindings/clock/imx7d-clock.h
> @@ -455,5 +455,7 @@
> #define IMX7D_SNVS_CLK 442
> #define IMX7D_CAAM_CLK 443
> #define IMX7D_KPP_ROOT_CLK 444
> -#define IMX7D_CLK_END 445
> +#define IMX7D_ENET1_IPG_ROOT_CLK 445
> +#define IMX7D_ENET2_IPG_ROOT_CLK 446
> +#define IMX7D_CLK_END 447
> #endif /* __DT_BINDINGS_CLOCK_IMX7D_H */
^ permalink raw reply
* [PATCH v8 15/15] dt: qcom: Add SAW regulator for 8x96 CPUs
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
1. Add syscon node for the SAW CPU registers
2. Add SAW regulators gang definition for s8-s11
3. Add voltages to the OPP tables
4. Add the s11 SAW regulator as CPU regulator
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 119 ++++++++++++++++++++++++++++++++++
1 file changed, 119 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index d96a112..871bfac 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
#include <dt-bindings/thermal/thermal.h>
+#include <dt-bindings/spmi/spmi.h>
/ {
model = "Qualcomm Technologies, Inc. MSM8996";
@@ -92,6 +93,7 @@
reg = <0x0 0x0>;
enable-method = "psci";
clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
next-level-cache = <&L2_0>;
@@ -107,6 +109,7 @@
reg = <0x0 0x1>;
enable-method = "psci";
clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
operating-points-v2 = <&cluster0_opp>;
#cooling-cells = <2>;
next-level-cache = <&L2_0>;
@@ -118,6 +121,7 @@
reg = <0x0 0x100>;
enable-method = "psci";
clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
operating-points-v2 = <&cluster1_opp>;
#cooling-cells = <2>;
next-level-cache = <&L2_1>;
@@ -133,6 +137,7 @@
reg = <0x0 0x101>;
enable-method = "psci";
clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
operating-points-v2 = <&cluster1_opp>;
#cooling-cells = <2>;
next-level-cache = <&L2_1>;
@@ -169,171 +174,205 @@
opp-307200000 {
opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x77>;
clock-latency-ns = <200000>;
};
opp-384000000 {
opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-422400000 {
opp-hz = /bits/ 64 <422400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-460800000 {
opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-480000000 {
opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-537600000 {
opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-556800000 {
opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-614400000 {
opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-652800000 {
opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-691200000 {
opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-729600000 {
opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-768000000 {
opp-hz = /bits/ 64 <768000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-844800000 {
opp-hz = /bits/ 64 <844800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x77>;
clock-latency-ns = <200000>;
};
opp-902400000 {
opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-960000000 {
opp-hz = /bits/ 64 <960000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-979200000 {
opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1036800000 {
opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1056000000 {
opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1113600000 {
opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1132800000 {
opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1190400000 {
opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1209600000 {
opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1228800000 {
opp-hz = /bits/ 64 <1228800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1286400000 {
opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1324800000 {
opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x5>;
clock-latency-ns = <200000>;
};
opp-1363200000 {
opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x72>;
clock-latency-ns = <200000>;
};
opp-1401600000 {
opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x5>;
clock-latency-ns = <200000>;
};
opp-1440000000 {
opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1478400000 {
opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
opp-1497600000 {
opp-hz = /bits/ 64 <1497600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x4>;
clock-latency-ns = <200000>;
};
opp-1516800000 {
opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1593600000 {
opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x71>;
clock-latency-ns = <200000>;
};
opp-1996800000 {
opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x20>;
clock-latency-ns = <200000>;
};
opp-2188800000 {
opp-hz = /bits/ 64 <2188800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x10>;
clock-latency-ns = <200000>;
};
@@ -346,251 +385,301 @@
opp-307200000 {
opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x77>;
clock-latency-ns = <200000>;
};
opp-384000000 {
opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-403200000 {
opp-hz = /bits/ 64 <403200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-460800000 {
opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-480000000 {
opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-537600000 {
opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-556800000 {
opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-614400000 {
opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-652800000 {
opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-691200000 {
opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-729600000 {
opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-748800000 {
opp-hz = /bits/ 64 <748800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-806400000 {
opp-hz = /bits/ 64 <806400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-825600000 {
opp-hz = /bits/ 64 <825600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-883200000 {
opp-hz = /bits/ 64 <883200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-902400000 {
opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-940800000 {
opp-hz = /bits/ 64 <940800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-979200000 {
opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1036800000 {
opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1056000000 {
opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1113600000 {
opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1132800000 {
opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1190400000 {
opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1209600000 {
opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1248000000 {
opp-hz = /bits/ 64 <1248000000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1286400000 {
opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <905000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1324800000 {
opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1363200000 {
opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1401600000 {
opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1440000000 {
opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1478400000 {
opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1516800000 {
opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1555200000 {
opp-hz = /bits/ 64 <1555200000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1593600000 {
opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1632000000 {
opp-hz = /bits/ 64 <1632000000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1670400000 {
opp-hz = /bits/ 64 <1670400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1708800000 {
opp-hz = /bits/ 64 <1708800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1747200000 {
opp-hz = /bits/ 64 <1747200000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1785600000 {
opp-hz = /bits/ 64 <1785600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x7>;
clock-latency-ns = <200000>;
};
opp-1804800000 {
opp-hz = /bits/ 64 <1804800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x6>;
clock-latency-ns = <200000>;
};
opp-1824000000 {
opp-hz = /bits/ 64 <1824000000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x71>;
clock-latency-ns = <200000>;
};
opp-1900800000 {
opp-hz = /bits/ 64 <1900800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x74>;
clock-latency-ns = <200000>;
};
opp-1920000000 {
opp-hz = /bits/ 64 <1920000000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
opp-1977600000 {
opp-hz = /bits/ 64 <1977600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x30>;
clock-latency-ns = <200000>;
};
opp-1996800000 {
opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
opp-2054400000 {
opp-hz = /bits/ 64 <2054400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x30>;
clock-latency-ns = <200000>;
};
opp-2073600000 {
opp-hz = /bits/ 64 <2073600000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
opp-2150400000 {
opp-hz = /bits/ 64 <2150400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x31>;
clock-latency-ns = <200000>;
};
opp-2246400000 {
opp-hz = /bits/ 64 <2246400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x10>;
clock-latency-ns = <200000>;
};
opp-2342400000 {
opp-hz = /bits/ 64 <2342400000>;
+ opp-microvolt = <1140000 905000 1140000>;
opp-supported-hw = <0x10>;
clock-latency-ns = <200000>;
};
@@ -908,6 +997,11 @@
#mbox-cells = <1>;
};
+ saw3: syscon at 9A10000 {
+ compatible = "syscon";
+ reg = <0x9A10000 0x1000>;
+ };
+
gcc: clock-controller at 300000 {
compatible = "qcom,gcc-msm8996";
#clock-cells = <1>;
@@ -1134,6 +1228,31 @@
#size-cells = <0>;
interrupt-controller;
#interrupt-cells = <4>;
+ pmic at 1 {
+ compatible = "qcom,pm8994", "qcom,spmi-pmic";
+ reg = <0x1 SPMI_USID>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ spm-regulators {
+ compatible = "qcom,pm8994-regulators";
+ qcom,saw-reg = <&saw3>;
+ s8 {
+ qcom,saw-slave;
+ };
+ s9 {
+ qcom,saw-slave;
+ };
+ s10 {
+ qcom,saw-slave;
+ };
+ pm8994_s11_saw: s11 {
+ qcom,saw-leader;
+ regulator-always-on;
+ regulator-min-microvolt = <905000>;
+ regulator-max-microvolt = <1140000>;
+ };
+ };
+ };
};
mmcc: clock-controller at 8c0000 {
--
1.9.1
^ permalink raw reply related
* [PATCH v8 14/15] dt-bindings: qcom_spmi: Document SAW support
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
Document the DT bindings for the SAW regulators.
The saw-leader is the only property that is configurable in DT.
The saw-slave property allows ganging (grouping) of
several regulators so that their outputs can be combined.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
.../bindings/regulator/qcom,spmi-regulator.txt | 45 ++++++++++++++++++++++
1 file changed, 45 insertions(+)
diff --git a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
index 57d2c65..406f2e5 100644
--- a/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
+++ b/Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt
@@ -110,6 +110,11 @@ Qualcomm SPMI Regulators
Definition: Reference to regulator supplying the input pin, as
described in the data sheet.
+- qcom,saw-reg:
+ Usage: optional
+ Value type: <phandle>
+ Description: Reference to syscon node defining the SAW registers.
+
The regulator node houses sub-nodes for each regulator within the device. Each
sub-node is identified using the node's name, with valid values listed for each
@@ -201,6 +206,17 @@ see regulator.txt - with additional custom properties described below:
2 = 0.55 uA
3 = 0.75 uA
+- qcom,saw-slave:
+ Usage: optional
+ Value type: <boo>
+ Description: SAW controlled gang slave. Will not be configured.
+
+- qcom,saw-leader:
+ Usage: optional
+ Value type: <boo>
+ Description: SAW controlled gang leader. Will be configured as
+ SAW regulator.
+
Example:
regulators {
@@ -221,3 +237,32 @@ Example:
....
};
+
+Example 2:
+
+ saw3: syscon at 9A10000 {
+ compatible = "syscon";
+ reg = <0x9A10000 0x1000>;
+ };
+
+ ...
+
+ spm-regulators {
+ compatible = "qcom,pm8994-regulators";
+ qcom,saw-reg = <&saw3>;
+ s8 {
+ qcom,saw-slave;
+ };
+ s9 {
+ qcom,saw-slave;
+ };
+ s10 {
+ qcom,saw-slave;
+ };
+ pm8994_s11_saw: s11 {
+ qcom,saw-leader;
+ regulator-always-on;
+ regulator-min-microvolt = <900000>;
+ regulator-max-microvolt = <1140000>;
+ };
+ };
--
1.9.1
^ permalink raw reply related
* [PATCH v8 13/15] regulator: qcom_spmi: Add support for SAW
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
Add support for SAW controlled regulators.
The regulators defined as SAW controlled in the device tree
will be controlled through special CPU registers instead of direct
SPMI accesses.
This is required especially for CPU supply regulators to synchronize
with clock scaling and for Automatic Voltage Switching.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/regulator/qcom_spmi-regulator.c | 133 +++++++++++++++++++++++++++++++-
1 file changed, 130 insertions(+), 3 deletions(-)
diff --git a/drivers/regulator/qcom_spmi-regulator.c b/drivers/regulator/qcom_spmi-regulator.c
index 63c7a0c..9817f1a 100644
--- a/drivers/regulator/qcom_spmi-regulator.c
+++ b/drivers/regulator/qcom_spmi-regulator.c
@@ -25,6 +25,8 @@
#include <linux/regulator/driver.h>
#include <linux/regmap.h>
#include <linux/list.h>
+#include <linux/mfd/syscon.h>
+#include <linux/io.h>
/* Pin control enable input pins. */
#define SPMI_REGULATOR_PIN_CTRL_ENABLE_NONE 0x00
@@ -181,6 +183,23 @@ enum spmi_boost_byp_registers {
SPMI_BOOST_BYP_REG_CURRENT_LIMIT = 0x4b,
};
+enum spmi_saw3_registers {
+ SAW3_SECURE = 0x00,
+ SAW3_ID = 0x04,
+ SAW3_SPM_STS = 0x0C,
+ SAW3_AVS_STS = 0x10,
+ SAW3_PMIC_STS = 0x14,
+ SAW3_RST = 0x18,
+ SAW3_VCTL = 0x1C,
+ SAW3_AVS_CTL = 0x20,
+ SAW3_AVS_LIMIT = 0x24,
+ SAW3_AVS_DLY = 0x28,
+ SAW3_AVS_HYSTERESIS = 0x2C,
+ SAW3_SPM_STS2 = 0x38,
+ SAW3_SPM_PMIC_DATA_3 = 0x4C,
+ SAW3_VERSION = 0xFD0,
+};
+
/* Used for indexing into ctrl_reg. These are offets from 0x40 */
enum spmi_common_control_register_index {
SPMI_COMMON_IDX_VOLTAGE_RANGE = 0,
@@ -1035,6 +1054,89 @@ static irqreturn_t spmi_regulator_vs_ocp_isr(int irq, void *data)
return IRQ_HANDLED;
}
+#define SAW3_VCTL_DATA_MASK 0xFF
+#define SAW3_VCTL_CLEAR_MASK 0x700FF
+#define SAW3_AVS_CTL_EN_MASK 0x1
+#define SAW3_AVS_CTL_TGGL_MASK 0x8000000
+#define SAW3_AVS_CTL_CLEAR_MASK 0x7efc00
+
+static struct regmap *saw_regmap = NULL;
+
+static void spmi_saw_set_vdd(void *data)
+{
+ u32 vctl, data3, avs_ctl, pmic_sts;
+ bool avs_enabled = false;
+ unsigned long timeout;
+ u8 voltage_sel = *(u8 *)data;
+
+ regmap_read(saw_regmap, SAW3_AVS_CTL, &avs_ctl);
+ regmap_read(saw_regmap, SAW3_VCTL, &vctl);
+ regmap_read(saw_regmap, SAW3_SPM_PMIC_DATA_3, &data3);
+
+ /* select the band */
+ vctl &= ~SAW3_VCTL_CLEAR_MASK;
+ vctl |= (u32)voltage_sel;
+
+ data3 &= ~SAW3_VCTL_CLEAR_MASK;
+ data3 |= (u32)voltage_sel;
+
+ /* If AVS is enabled, switch it off during the voltage change */
+ avs_enabled = SAW3_AVS_CTL_EN_MASK & avs_ctl;
+ if (avs_enabled) {
+ avs_ctl &= ~SAW3_AVS_CTL_TGGL_MASK;
+ regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
+ }
+
+ regmap_write(saw_regmap, SAW3_RST, 1);
+ regmap_write(saw_regmap, SAW3_VCTL, vctl);
+ regmap_write(saw_regmap, SAW3_SPM_PMIC_DATA_3, data3);
+
+ timeout = jiffies + usecs_to_jiffies(100);
+ do {
+ regmap_read(saw_regmap, SAW3_PMIC_STS, &pmic_sts);
+ pmic_sts &= SAW3_VCTL_DATA_MASK;
+ if (pmic_sts == (u32)voltage_sel)
+ break;
+
+ cpu_relax();
+
+ } while (time_before(jiffies, timeout));
+
+ /* After successful voltage change, switch the AVS back on */
+ if (avs_enabled) {
+ pmic_sts &= 0x3f;
+ avs_ctl &= ~SAW3_AVS_CTL_CLEAR_MASK;
+ avs_ctl |= ((pmic_sts - 4) << 10);
+ avs_ctl |= (pmic_sts << 17);
+ avs_ctl |= SAW3_AVS_CTL_TGGL_MASK;
+ regmap_write(saw_regmap, SAW3_AVS_CTL, avs_ctl);
+ }
+}
+
+static int
+spmi_regulator_saw_set_voltage(struct regulator_dev *rdev, unsigned selector)
+{
+ struct spmi_regulator *vreg = rdev_get_drvdata(rdev);
+ int ret;
+ u8 range_sel, voltage_sel;
+
+ ret = spmi_sw_selector_to_hw(vreg, selector, &range_sel, &voltage_sel);
+ if (ret)
+ return ret;
+
+ if (0 != range_sel) {
+ dev_dbg(&rdev->dev, "range_sel = %02X voltage_sel = %02X", \
+ range_sel, voltage_sel);
+ return -EINVAL;
+ }
+
+ /* Always do the SAW register writes on the first CPU */
+ return smp_call_function_single(0, spmi_saw_set_vdd, \
+ &voltage_sel, true);
+}
+
+static struct regulator_ops spmi_saw_ops = {};
+
static struct regulator_ops spmi_smps_ops = {
.enable = regulator_enable_regmap,
.disable = regulator_disable_regmap,
@@ -1250,6 +1352,7 @@ static int spmi_regulator_match(struct spmi_regulator *vreg, u16 force_type)
}
dig_major_rev = version[SPMI_COMMON_REG_DIG_MAJOR_REV
- SPMI_COMMON_REG_DIG_MAJOR_REV];
+
if (!force_type) {
type = version[SPMI_COMMON_REG_TYPE -
SPMI_COMMON_REG_DIG_MAJOR_REV];
@@ -1648,7 +1751,9 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
struct regmap *regmap;
const char *name;
struct device *dev = &pdev->dev;
- int ret;
+ struct device_node *node = pdev->dev.of_node;
+ struct device_node *syscon;
+ int ret, lenp;
struct list_head *vreg_list;
vreg_list = devm_kzalloc(dev, sizeof(*vreg_list), GFP_KERNEL);
@@ -1665,7 +1770,22 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
if (!match)
return -ENODEV;
+ if (of_find_property(node, "qcom,saw-reg", &lenp)) {
+ syscon = of_parse_phandle(node, "qcom,saw-reg", 0);
+ saw_regmap = syscon_node_to_regmap(syscon);
+ of_node_put(syscon);
+ if (IS_ERR(regmap))
+ dev_err(dev, "ERROR reading SAW regmap\n");
+ }
+
for (reg = match->data; reg->name; reg++) {
+
+ if (saw_regmap && \
+ of_find_property(of_find_node_by_name(node, reg->name), \
+ "qcom,saw-slave", &lenp)) {
+ continue;
+ }
+
vreg = devm_kzalloc(dev, sizeof(*vreg), GFP_KERNEL);
if (!vreg)
return -ENOMEM;
@@ -1673,7 +1793,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
vreg->dev = dev;
vreg->base = reg->base;
vreg->regmap = regmap;
-
if (reg->ocp) {
vreg->ocp_irq = platform_get_irq_byname(pdev, reg->ocp);
if (vreg->ocp_irq < 0) {
@@ -1681,7 +1800,6 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
goto err;
}
}
-
vreg->desc.id = -1;
vreg->desc.owner = THIS_MODULE;
vreg->desc.type = REGULATOR_VOLTAGE;
@@ -1698,6 +1816,15 @@ static int qcom_spmi_regulator_probe(struct platform_device *pdev)
if (ret)
continue;
+ if (saw_regmap && \
+ of_find_property(of_find_node_by_name(node, reg->name), \
+ "qcom,saw-leader", &lenp)) {
+ spmi_saw_ops = *(vreg->desc.ops);
+ spmi_saw_ops.set_voltage_sel = \
+ spmi_regulator_saw_set_voltage;
+ vreg->desc.ops = &spmi_saw_ops;
+ }
+
config.dev = dev;
config.driver_data = vreg;
config.regmap = regmap;
--
1.9.1
^ permalink raw reply related
* [PATCH v8 12/15] dt: qcom: Add qcom-cpufreq-kryo driver configuration
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
1. Add NVMEM node for the speedbin
2. Add definitions for all possible MSM8996 CPU OPPs.
The qcom-cpufreq-kryo driver will select the appropriate subset.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
arch/arm64/boot/dts/qcom/apq8096-db820c.dts | 2 +-
arch/arm64/boot/dts/qcom/msm8996.dtsi | 281 ++++++++++++++++++++++++++--
2 files changed, 270 insertions(+), 13 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
index 230e9c8..da23bda 100644
--- a/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
+++ b/arch/arm64/boot/dts/qcom/apq8096-db820c.dts
@@ -17,5 +17,5 @@
/ {
model = "Qualcomm Technologies, Inc. DB820c";
- compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc";
+ compatible = "arrow,apq8096-db820c", "qcom,apq8096-sbc", "qcom,apq8096";
};
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index e6cf290..d96a112 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -1,13 +1,6 @@
-/* Copyright (c) 2014-2015, The Linux Foundation. All rights reserved.
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 and
- * only version 2 as published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful,
- * but WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
- * GNU General Public License for more details.
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2014-2015, 2018 The Linux Foundation. All rights reserved.
*/
#include <dt-bindings/interrupt-controller/arm-gic.h>
@@ -169,177 +162,436 @@
};
cluster0_opp: opp_table0 {
- compatible = "operating-points-v2";
+ compatible = "operating-points-v2-kryo-cpu",
+ "operating-points-v2";
+ nvmem-cells = <&speedbin_efuse>;
opp-shared;
opp-307200000 {
opp-hz = /bits/ 64 <307200000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-422400000 {
opp-hz = /bits/ 64 <422400000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-480000000 {
opp-hz = /bits/ 64 <480000000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-556800000 {
opp-hz = /bits/ 64 <556800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-652800000 {
opp-hz = /bits/ 64 <652800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-729600000 {
opp-hz = /bits/ 64 <729600000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-768000000 {
+ opp-hz = /bits/ 64 <768000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-844800000 {
opp-hz = /bits/ 64 <844800000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-960000000 {
opp-hz = /bits/ 64 <960000000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1036800000 {
opp-hz = /bits/ 64 <1036800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1113600000 {
opp-hz = /bits/ 64 <1113600000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1190400000 {
opp-hz = /bits/ 64 <1190400000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1228800000 {
opp-hz = /bits/ 64 <1228800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1324800000 {
opp-hz = /bits/ 64 <1324800000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-supported-hw = <0x72>;
clock-latency-ns = <200000>;
};
opp-1401600000 {
opp-hz = /bits/ 64 <1401600000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1478400000 {
opp-hz = /bits/ 64 <1478400000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1497600000 {
+ opp-hz = /bits/ 64 <1497600000>;
+ opp-supported-hw = <0x4>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1593600000 {
opp-hz = /bits/ 64 <1593600000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-supported-hw = <0x20>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2188800000 {
+ opp-hz = /bits/ 64 <2188800000>;
+ opp-supported-hw = <0x10>;
clock-latency-ns = <200000>;
};
};
cluster1_opp: opp_table1 {
- compatible = "operating-points-v2";
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
opp-shared;
opp-307200000 {
opp-hz = /bits/ 64 <307200000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-403200000 {
opp-hz = /bits/ 64 <403200000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-480000000 {
opp-hz = /bits/ 64 <480000000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-556800000 {
opp-hz = /bits/ 64 <556800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-652800000 {
opp-hz = /bits/ 64 <652800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-729600000 {
opp-hz = /bits/ 64 <729600000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-748800000 {
+ opp-hz = /bits/ 64 <748800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-806400000 {
opp-hz = /bits/ 64 <806400000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-883200000 {
opp-hz = /bits/ 64 <883200000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-940800000 {
opp-hz = /bits/ 64 <940800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1036800000 {
opp-hz = /bits/ 64 <1036800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1113600000 {
opp-hz = /bits/ 64 <1113600000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1190400000 {
opp-hz = /bits/ 64 <1190400000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1248000000 {
opp-hz = /bits/ 64 <1248000000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1324800000 {
opp-hz = /bits/ 64 <1324800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1401600000 {
opp-hz = /bits/ 64 <1401600000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1478400000 {
opp-hz = /bits/ 64 <1478400000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1555200000 {
opp-hz = /bits/ 64 <1555200000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1632000000 {
opp-hz = /bits/ 64 <1632000000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1708800000 {
opp-hz = /bits/ 64 <1708800000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1747200000 {
+ opp-hz = /bits/ 64 <1747200000>;
+ opp-supported-hw = <0x70>;
clock-latency-ns = <200000>;
};
opp-1785600000 {
opp-hz = /bits/ 64 <1785600000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1804800000 {
+ opp-hz = /bits/ 64 <1804800000>;
+ opp-supported-hw = <0x6>;
clock-latency-ns = <200000>;
};
opp-1824000000 {
opp-hz = /bits/ 64 <1824000000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1900800000 {
+ opp-hz = /bits/ 64 <1900800000>;
+ opp-supported-hw = <0x74>;
clock-latency-ns = <200000>;
};
opp-1920000000 {
opp-hz = /bits/ 64 <1920000000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1977600000 {
+ opp-hz = /bits/ 64 <1977600000>;
+ opp-supported-hw = <0x30>;
clock-latency-ns = <200000>;
};
opp-1996800000 {
opp-hz = /bits/ 64 <1996800000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2054400000 {
+ opp-hz = /bits/ 64 <2054400000>;
+ opp-supported-hw = <0x30>;
clock-latency-ns = <200000>;
};
opp-2073600000 {
opp-hz = /bits/ 64 <2073600000>;
+ opp-supported-hw = <0x1>;
clock-latency-ns = <200000>;
};
opp-2150400000 {
opp-hz = /bits/ 64 <2150400000>;
+ opp-supported-hw = <0x31>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2342400000 {
+ opp-hz = /bits/ 64 <2342400000>;
+ opp-supported-hw = <0x10>;
clock-latency-ns = <200000>;
};
};
@@ -917,6 +1169,11 @@
reg = <0x24f 0x1>;
bits = <1 4>;
};
+
+ speedbin_efuse: speedbin at 133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
};
phy at 34000 {
--
1.9.1
^ permalink raw reply related
* [PATCH v8 11/15] dt-bindings: cpufreq: Document operating-points-v2-kryo-cpu
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
This change adds documentation for the DT bindings.
The "operating-points-v2-kryo-cpu" DT extends the "operating-points-v2"
with following parameters:
- nvmem-cells (NVMEM area containig the speedbin information)
- opp-supported-hw: A single 32 bit bitmap value,
representing compatible HW:
0: MSM8996 V3, speedbin 0
1: MSM8996 V3, speedbin 1
2: MSM8996 V3, speedbin 2
3: unused
4: MSM8996 SG, speedbin 0
5: MSM8996 SG, speedbin 1
6: MSM8996 SG, speedbin 2
7-31: unused
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
.../devicetree/bindings/opp/kryo-cpufreq.txt | 680 +++++++++++++++++++++
1 file changed, 680 insertions(+)
create mode 100644 Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
diff --git a/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
new file mode 100644
index 0000000..c2127b9
--- /dev/null
+++ b/Documentation/devicetree/bindings/opp/kryo-cpufreq.txt
@@ -0,0 +1,680 @@
+Qualcomm Technologies, Inc. KRYO CPUFreq and OPP bindings
+===================================
+
+In Certain Qualcomm Technologies, Inc. SoCs like apq8096 and msm8996
+that have KRYO processors, the CPU ferequencies subset and voltage value
+of each OPP varies based on the silicon variant in use.
+Qualcomm Technologies, Inc. Process Voltage Scaling Tables
+defines the voltage and frequency value based on the msm-id in SMEM
+and speedbin blown in the efuse combination.
+The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+to provide the OPP framework with required information (existing HW bitmap).
+This is used to determine the voltage and frequency value for each OPP of
+operating-points-v2 table when it is parsed by the OPP framework.
+
+Required properties:
+--------------------
+In 'cpus' nodes:
+- operating-points-v2: Phandle to the operating-points-v2 table to use.
+
+In 'operating-points-v2' table:
+- compatible: Should be
+ - 'operating-points-v2-kryo-cpu' for apq8096 and msm8996.
+- nvmem-cells: A phandle pointing to a nvmem-cells node representing the
+ efuse registers that has information about the
+ speedbin that is used to select the right frequency/voltage
+ value pair.
+ Please refer the for nvmem-cells
+ bindings Documentation/devicetree/bindings/nvmem/nvmem.txt
+ and also examples below.
+
+In every OPP node:
+- opp-supported-hw: A single 32 bit bitmap value, representing compatible HW.
+ Bitmap:
+ 0: MSM8996 V3, speedbin 0
+ 1: MSM8996 V3, speedbin 1
+ 2: MSM8996 V3, speedbin 2
+ 3: unused
+ 4: MSM8996 SG, speedbin 0
+ 5: MSM8996 SG, speedbin 1
+ 6: MSM8996 SG, speedbin 2
+ 7-31: unused
+
+Example 1:
+---------
+
+ cpus {
+ #address-cells = <2>;
+ #size-cells = <0>;
+
+ CPU0: cpu at 0 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x0>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ L2_0: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU1: cpu at 1 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x1>;
+ enable-method = "psci";
+ clocks = <&kryocc 0>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_0>;
+ };
+
+ CPU2: cpu at 100 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x100>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ L2_1: l2-cache {
+ compatible = "cache";
+ cache-level = <2>;
+ };
+ };
+
+ CPU3: cpu at 101 {
+ device_type = "cpu";
+ compatible = "qcom,kryo";
+ reg = <0x0 0x101>;
+ enable-method = "psci";
+ clocks = <&kryocc 1>;
+ cpu-supply = <&pm8994_s11_saw>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
+ next-level-cache = <&L2_1>;
+ };
+
+ cpu-map {
+ cluster0 {
+ core0 {
+ cpu = <&CPU0>;
+ };
+
+ core1 {
+ cpu = <&CPU1>;
+ };
+ };
+
+ cluster1 {
+ core0 {
+ cpu = <&CPU2>;
+ };
+
+ core1 {
+ cpu = <&CPU3>;
+ };
+ };
+ };
+ };
+
+ cluster0_opp: opp_table0 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-422400000 {
+ opp-hz = /bits/ 64 <422400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-768000000 {
+ opp-hz = /bits/ 64 <768000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-844800000 {
+ opp-hz = /bits/ 64 <844800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-960000000 {
+ opp-hz = /bits/ 64 <960000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1228800000 {
+ opp-hz = /bits/ 64 <1228800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x72>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x5>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1497600000 {
+ opp-hz = /bits/ 64 <1497600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x4>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x20>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2188800000 {
+ opp-hz = /bits/ 64 <2188800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+ cluster1_opp: opp_table1 {
+ compatible = "operating-points-v2-kryo-cpu";
+ nvmem-cells = <&speedbin_efuse>;
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x77>;
+ clock-latency-ns = <200000>;
+ };
+ opp-384000000 {
+ opp-hz = /bits/ 64 <384000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-403200000 {
+ opp-hz = /bits/ 64 <403200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-460800000 {
+ opp-hz = /bits/ 64 <460800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-537600000 {
+ opp-hz = /bits/ 64 <537600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-614400000 {
+ opp-hz = /bits/ 64 <614400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-691200000 {
+ opp-hz = /bits/ 64 <691200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-748800000 {
+ opp-hz = /bits/ 64 <748800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-806400000 {
+ opp-hz = /bits/ 64 <806400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-825600000 {
+ opp-hz = /bits/ 64 <825600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-883200000 {
+ opp-hz = /bits/ 64 <883200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-902400000 {
+ opp-hz = /bits/ 64 <902400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-979200000 {
+ opp-hz = /bits/ 64 <979200000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1056000000 {
+ opp-hz = /bits/ 64 <1056000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1132800000 {
+ opp-hz = /bits/ 64 <1132800000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1209600000 {
+ opp-hz = /bits/ 64 <1209600000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1248000000 {
+ opp-hz = /bits/ 64 <1248000000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1286400000 {
+ opp-hz = /bits/ 64 <1286400000>;
+ opp-microvolt = <905000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1363200000 {
+ opp-hz = /bits/ 64 <1363200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1440000000 {
+ opp-hz = /bits/ 64 <1440000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1516800000 {
+ opp-hz = /bits/ 64 <1516800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1555200000 {
+ opp-hz = /bits/ 64 <1555200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1632000000 {
+ opp-hz = /bits/ 64 <1632000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1670400000 {
+ opp-hz = /bits/ 64 <1670400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1708800000 {
+ opp-hz = /bits/ 64 <1708800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1747200000 {
+ opp-hz = /bits/ 64 <1747200000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x70>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1785600000 {
+ opp-hz = /bits/ 64 <1785600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x7>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1804800000 {
+ opp-hz = /bits/ 64 <1804800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x6>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1824000000 {
+ opp-hz = /bits/ 64 <1824000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x71>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1900800000 {
+ opp-hz = /bits/ 64 <1900800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x74>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1920000000 {
+ opp-hz = /bits/ 64 <1920000000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1977600000 {
+ opp-hz = /bits/ 64 <1977600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2054400000 {
+ opp-hz = /bits/ 64 <2054400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x30>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2073600000 {
+ opp-hz = /bits/ 64 <2073600000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x1>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2150400000 {
+ opp-hz = /bits/ 64 <2150400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x31>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2246400000 {
+ opp-hz = /bits/ 64 <2246400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2342400000 {
+ opp-hz = /bits/ 64 <2342400000>;
+ opp-microvolt = <1140000 905000 1140000>;
+ opp-supported-hw = <0x10>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+....
+
+reserved-memory {
+ #address-cells = <2>;
+ #size-cells = <2>;
+ ranges;
+....
+ smem_mem: smem-mem at 86000000 {
+ reg = <0x0 0x86000000 0x0 0x200000>;
+ no-map;
+ };
+....
+};
+
+smem {
+ compatible = "qcom,smem";
+ memory-region = <&smem_mem>;
+ hwlocks = <&tcsr_mutex 3>;
+};
+
+soc {
+....
+ qfprom: qfprom at 74000 {
+ compatible = "qcom,qfprom";
+ reg = <0x00074000 0x8ff>;
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ....
+ speedbin_efuse: speedbin at 133 {
+ reg = <0x133 0x1>;
+ bits = <5 3>;
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related
* [PATCH v8 10/15] cpufreq: Add Kryo CPU scaling driver
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
the CPU frequency subset and voltage value of each OPP varies
based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
defines the voltage and frequency value based on the msm-id in SMEM
and speedbin blown in the efuse combination.
The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
to provide the OPP framework with required information.
This is used to determine the voltage and frequency value for each OPP of
operating-points-v2 table when it is parsed by the OPP framework.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
drivers/cpufreq/Kconfig.arm | 10 +++
drivers/cpufreq/Makefile | 1 +
drivers/cpufreq/cpufreq-dt-platdev.c | 3 +
drivers/cpufreq/qcom-cpufreq-kryo.c | 166 +++++++++++++++++++++++++++++++++++
4 files changed, 180 insertions(+)
create mode 100644 drivers/cpufreq/qcom-cpufreq-kryo.c
diff --git a/drivers/cpufreq/Kconfig.arm b/drivers/cpufreq/Kconfig.arm
index de55c7d..0bfd40e 100644
--- a/drivers/cpufreq/Kconfig.arm
+++ b/drivers/cpufreq/Kconfig.arm
@@ -124,6 +124,16 @@ config ARM_OMAP2PLUS_CPUFREQ
depends on ARCH_OMAP2PLUS
default ARCH_OMAP2PLUS
+config ARM_QCOM_CPUFREQ_KRYO
+ bool "Qualcomm Kryo based CPUFreq"
+ depends on QCOM_QFPROM
+ depends on QCOM_SMEM
+ select PM_OPP
+ help
+ This adds the CPUFreq driver for Qualcomm Kryo SoC based boards.
+
+ If in doubt, say N.
+
config ARM_S3C_CPUFREQ
bool
help
diff --git a/drivers/cpufreq/Makefile b/drivers/cpufreq/Makefile
index 8d24ade..fb4a2ec 100644
--- a/drivers/cpufreq/Makefile
+++ b/drivers/cpufreq/Makefile
@@ -65,6 +65,7 @@ obj-$(CONFIG_MACH_MVEBU_V7) += mvebu-cpufreq.o
obj-$(CONFIG_ARM_OMAP2PLUS_CPUFREQ) += omap-cpufreq.o
obj-$(CONFIG_ARM_PXA2xx_CPUFREQ) += pxa2xx-cpufreq.o
obj-$(CONFIG_PXA3xx) += pxa3xx-cpufreq.o
+obj-$(CONFIG_ARM_QCOM_CPUFREQ_KRYO) += qcom-cpufreq-kryo.o
obj-$(CONFIG_ARM_S3C2410_CPUFREQ) += s3c2410-cpufreq.o
obj-$(CONFIG_ARM_S3C2412_CPUFREQ) += s3c2412-cpufreq.o
obj-$(CONFIG_ARM_S3C2416_CPUFREQ) += s3c2416-cpufreq.o
diff --git a/drivers/cpufreq/cpufreq-dt-platdev.c b/drivers/cpufreq/cpufreq-dt-platdev.c
index 3b585e4..77d6ab8 100644
--- a/drivers/cpufreq/cpufreq-dt-platdev.c
+++ b/drivers/cpufreq/cpufreq-dt-platdev.c
@@ -118,6 +118,9 @@
{ .compatible = "nvidia,tegra124", },
+ { .compatible = "qcom,apq8096", },
+ { .compatible = "qcom,msm8996", },
+
{ .compatible = "st,stih407", },
{ .compatible = "st,stih410", },
diff --git a/drivers/cpufreq/qcom-cpufreq-kryo.c b/drivers/cpufreq/qcom-cpufreq-kryo.c
new file mode 100644
index 0000000..a2b9fb2
--- /dev/null
+++ b/drivers/cpufreq/qcom-cpufreq-kryo.c
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+/*
+ * In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
+ * the CPU frequency subset and voltage value of each OPP varies
+ * based on the silicon variant in use. Qualcomm Process Voltage Scaling Tables
+ * defines the voltage and frequency value based on the msm-id in SMEM
+ * and speedbin blown in the efuse combination.
+ * The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the SoC
+ * to provide the OPP framework with required information.
+ * This is used to determine the voltage and frequency value for each OPP of
+ * operating-points-v2 table when it is parsed by the OPP framework.
+ */
+
+#include <linux/cpu.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/nvmem-consumer.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pm_opp.h>
+#include <linux/slab.h>
+#include <linux/soc/qcom/smem.h>
+
+#define MSM_ID_SMEM 137
+#define SILVER_LEAD 0
+#define GOLD_LEAD 2
+
+enum _msm_id {
+ MSM8996V3 = 0xF6ul,
+ APQ8096V3 = 0x123ul,
+ MSM8996SG = 0x131ul,
+ APQ8096SG = 0x138ul,
+};
+
+enum _msm8996_version {
+ MSM8996_V3,
+ MSM8996_SG,
+ NUM_OF_MSM8996_VERSIONS,
+};
+
+static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void)
+{
+ size_t len;
+ u32 *msm_id;
+ enum _msm8996_version version;
+
+ msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len);
+ /* The first 4 bytes are format, next to them is the actual msm-id */
+ msm_id++;
+
+ switch ((enum _msm_id)*msm_id) {
+ case MSM8996V3:
+ case APQ8096V3:
+ version = MSM8996_V3;
+ break;
+ case MSM8996SG:
+ case APQ8096SG:
+ version = MSM8996_SG;
+ break;
+ default:
+ version = NUM_OF_MSM8996_VERSIONS;
+ }
+
+ return version;
+}
+
+static int __init qcom_cpufreq_kryo_driver_init(void)
+{
+ size_t len;
+ int ret = 0;
+ u32 versions;
+ enum _msm8996_version msm8996_version;
+ u8 *speedbin;
+ struct device *cpu_dev_silver, *cpu_dev_gold;
+ struct device_node *np;
+ struct nvmem_cell *speedbin_nvmem;
+ struct platform_device *pdev;
+ struct opp_table *opp_silver = NULL;
+ struct opp_table *opp_gold = NULL;
+
+ cpu_dev_silver = get_cpu_device(SILVER_LEAD);
+ if (IS_ERR_OR_NULL(cpu_dev_silver))
+ return PTR_ERR(cpu_dev_silver);
+
+ cpu_dev_gold = get_cpu_device(SILVER_LEAD);
+ if (IS_ERR_OR_NULL(cpu_dev_gold))
+ return PTR_ERR(cpu_dev_gold);
+
+ msm8996_version = qcom_cpufreq_kryo_get_msm_id();
+ if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
+ dev_err(cpu_dev_silver, "Not Snapdragon 820/821!");
+ return -ENODEV;
+ }
+
+ np = dev_pm_opp_of_get_opp_desc_node(cpu_dev_silver);
+ if (IS_ERR_OR_NULL(np))
+ return PTR_ERR(np);
+
+ if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) {
+ ret = -ENOENT;
+ goto free_np;
+ }
+
+ speedbin_nvmem = of_nvmem_cell_get(np, NULL);
+ if (IS_ERR(speedbin_nvmem)) {
+ ret = PTR_ERR(speedbin_nvmem);
+ dev_err(cpu_dev_silver, "Could not get nvmem cell: %d\n", ret);
+ goto free_np;
+ }
+
+ speedbin = nvmem_cell_read(speedbin_nvmem, &len);
+ nvmem_cell_put(speedbin_nvmem);
+
+ switch (msm8996_version) {
+ case MSM8996_V3:
+ versions = 1 << (unsigned int)(*speedbin);
+ break;
+ case MSM8996_SG:
+ versions = 1 << ((unsigned int)(*speedbin) + 4);
+ break;
+ default:
+ BUG();
+ break;
+ }
+
+ opp_silver = dev_pm_opp_set_supported_hw(cpu_dev_silver,&versions,1);
+ if (IS_ERR_OR_NULL(opp_silver)) {
+ dev_err(cpu_dev_silver, "Failed to set supported hardware\n");
+ ret = PTR_ERR(opp_silver);
+ goto free_np;
+ }
+
+ opp_gold = dev_pm_opp_set_supported_hw(cpu_dev_gold,&versions,1);
+ if (IS_ERR_OR_NULL(opp_gold)) {
+ dev_err(cpu_dev_gold, "Failed to set supported hardware\n");
+ ret = PTR_ERR(opp_gold);
+ goto free_opp_silver;
+ }
+
+ pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
+ if (!IS_ERR_OR_NULL(pdev))
+ goto out;
+
+ ret = PTR_ERR(pdev);
+ dev_err(cpu_dev_silver, "Failed to register platform device\n");
+ dev_pm_opp_put_supported_hw(opp_gold);
+
+free_opp_silver:
+ dev_pm_opp_put_supported_hw(opp_silver);
+
+free_np:
+ of_node_put(np);
+
+out:
+ return ret;
+}
+late_initcall(qcom_cpufreq_kryo_driver_init);
+
+MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related
* [PATCH v8 09/15] dt: qcom: Add opp and thermal to the msm8996
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
---
arch/arm64/boot/dts/qcom/msm8996.dtsi | 269 ++++++++++++++++++++++++++++++++--
1 file changed, 260 insertions(+), 9 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/msm8996.dtsi b/arch/arm64/boot/dts/qcom/msm8996.dtsi
index 37b7152c..e6cf290 100644
--- a/arch/arm64/boot/dts/qcom/msm8996.dtsi
+++ b/arch/arm64/boot/dts/qcom/msm8996.dtsi
@@ -14,6 +14,7 @@
#include <dt-bindings/clock/qcom,gcc-msm8996.h>
#include <dt-bindings/clock/qcom,mmcc-msm8996.h>
#include <dt-bindings/clock/qcom,rpmcc.h>
+#include <dt-bindings/thermal/thermal.h>
/ {
model = "Qualcomm Technologies, Inc. MSM8996";
@@ -97,6 +98,9 @@
compatible = "qcom,kryo";
reg = <0x0 0x0>;
enable-method = "psci";
+ clocks = <&kryocc 0>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_0>;
L2_0: l2-cache {
compatible = "cache";
@@ -109,6 +113,9 @@
compatible = "qcom,kryo";
reg = <0x0 0x1>;
enable-method = "psci";
+ clocks = <&kryocc 0>;
+ operating-points-v2 = <&cluster0_opp>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_0>;
};
@@ -117,6 +124,9 @@
compatible = "qcom,kryo";
reg = <0x0 0x100>;
enable-method = "psci";
+ clocks = <&kryocc 1>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_1>;
L2_1: l2-cache {
compatible = "cache";
@@ -129,6 +139,9 @@
compatible = "qcom,kryo";
reg = <0x0 0x101>;
enable-method = "psci";
+ clocks = <&kryocc 1>;
+ operating-points-v2 = <&cluster1_opp>;
+ #cooling-cells = <2>;
next-level-cache = <&L2_1>;
};
@@ -155,6 +168,182 @@
};
};
+ cluster0_opp: opp_table0 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-422400000 {
+ opp-hz = /bits/ 64 <422400000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-844800000 {
+ opp-hz = /bits/ 64 <844800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-960000000 {
+ opp-hz = /bits/ 64 <960000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1228800000 {
+ opp-hz = /bits/ 64 <1228800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1593600000 {
+ opp-hz = /bits/ 64 <1593600000>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
+ cluster1_opp: opp_table1 {
+ compatible = "operating-points-v2";
+ opp-shared;
+
+ opp-307200000 {
+ opp-hz = /bits/ 64 <307200000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-403200000 {
+ opp-hz = /bits/ 64 <403200000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-480000000 {
+ opp-hz = /bits/ 64 <480000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-556800000 {
+ opp-hz = /bits/ 64 <556800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-652800000 {
+ opp-hz = /bits/ 64 <652800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-729600000 {
+ opp-hz = /bits/ 64 <729600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-806400000 {
+ opp-hz = /bits/ 64 <806400000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-883200000 {
+ opp-hz = /bits/ 64 <883200000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-940800000 {
+ opp-hz = /bits/ 64 <940800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1036800000 {
+ opp-hz = /bits/ 64 <1036800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1113600000 {
+ opp-hz = /bits/ 64 <1113600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1190400000 {
+ opp-hz = /bits/ 64 <1190400000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1248000000 {
+ opp-hz = /bits/ 64 <1248000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1324800000 {
+ opp-hz = /bits/ 64 <1324800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1401600000 {
+ opp-hz = /bits/ 64 <1401600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1478400000 {
+ opp-hz = /bits/ 64 <1478400000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1555200000 {
+ opp-hz = /bits/ 64 <1555200000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1632000000 {
+ opp-hz = /bits/ 64 <1632000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1708800000 {
+ opp-hz = /bits/ 64 <1708800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1785600000 {
+ opp-hz = /bits/ 64 <1785600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1824000000 {
+ opp-hz = /bits/ 64 <1824000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1920000000 {
+ opp-hz = /bits/ 64 <1920000000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-1996800000 {
+ opp-hz = /bits/ 64 <1996800000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2073600000 {
+ opp-hz = /bits/ 64 <2073600000>;
+ clock-latency-ns = <200000>;
+ };
+ opp-2150400000 {
+ opp-hz = /bits/ 64 <2150400000>;
+ clock-latency-ns = <200000>;
+ };
+ };
+
thermal-zones {
cpu-thermal0 {
polling-delay-passive = <250>;
@@ -163,18 +352,34 @@
thermal-sensors = <&tsens0 3>;
trips {
- cpu_alert0: trip0 {
+ cpu_alert0: cpu_alert0 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn0: cpu_warn0 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
- cpu_crit0: trip1 {
+ cpu_crit0: cpu_crit0 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert0>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn0>;
+ cooling-device = <&CPU0 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
cpu-thermal1 {
@@ -184,18 +389,34 @@
thermal-sensors = <&tsens0 5>;
trips {
- cpu_alert1: trip0 {
+ cpu_alert1: cpu_alert1 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn1: cpu_warn1 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
- cpu_crit1: trip1 {
+ cpu_crit1: cpu_crit1 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert1>;
+ cooling-device = <&CPU0 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn1>;
+ cooling-device = <&CPU0 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
cpu-thermal2 {
@@ -205,18 +426,33 @@
thermal-sensors = <&tsens0 8>;
trips {
- cpu_alert2: trip0 {
+ cpu_alert2: cpu_alert2 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn2: cpu_warn2 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
- cpu_crit2: trip1 {
+ cpu_crit2: cpu_crit2 {
temperature = <110000>;
hysteresis = <2000>;
type = "critical";
};
};
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert2>;
+ cooling-device = <&CPU2 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn2>;
+ cooling-device = <&CPU2 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
cpu-thermal3 {
@@ -226,9 +462,14 @@
thermal-sensors = <&tsens0 10>;
trips {
- cpu_alert3: trip0 {
+ cpu_alert3: cpu_alert3 {
temperature = <75000>;
hysteresis = <2000>;
+ type = "active";
+ };
+ cpu_warn3: cpu_warn3 {
+ temperature = <90000>;
+ hysteresis = <2000>;
type = "passive";
};
@@ -238,6 +479,16 @@
type = "critical";
};
};
+ cooling-maps {
+ map0 {
+ trip = <&cpu_alert3>;
+ cooling-device = <&CPU2 THERMAL_NO_LIMIT 7>;
+ };
+ map1 {
+ trip = <&cpu_warn3>;
+ cooling-device = <&CPU2 8 THERMAL_NO_LIMIT>;
+ };
+ };
};
};
@@ -414,7 +665,7 @@
};
kryocc: clock-controller at 6400000 {
- compatible = "qcom,apcc-msm8996";
+ compatible = "qcom,msm8996-apcc";
reg = <0x6400000 0x90000>;
#clock-cells = <1>;
};
@@ -1001,7 +1252,7 @@
pinctrl-names = "default", "sleep";
pinctrl-0 = <&pcie2_clkreq_default &pcie2_perst_default &pcie2_wake_default>;
- pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep >;
+ pinctrl-1 = <&pcie2_clkreq_sleep &pcie2_perst_default &pcie2_wake_sleep>;
vdda-supply = <&pm8994_l28>;
--
1.9.1
^ permalink raw reply related
* [PATCH v8 08/15] clk: qcom: Add ACD path to CPU clock driver for msm8996
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
The PMUX for each duplex allows for selection of ACD clock source.
The DVM (Dynamic Variation Monitor) will flag an error
when a voltage droop event is detected. This flagged error
enables ACD to provide a div-by-2 clock, sourced from the primary PLL.
The duplex will be provided the divided clock
until a pre-programmed delay has expired.
This change configures ACD during the probe and switches
the PMUXes to the ACD clock source.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 75 +++++++++++++++++++++++++++++++++++------
1 file changed, 65 insertions(+), 10 deletions(-)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index ff5c0a5..0a908d8 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -53,9 +53,11 @@
*/
#include <linux/clk.h>
+#include <linux/clk-provider.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
+#include <soc/qcom/kryo-l2-accessors.h>
#include "clk-alpha-pll.h"
#include "clk-regmap.h"
@@ -69,6 +71,11 @@ enum _pmux_input {
};
#define DIV_2_THRESHOLD 600000000
+#define PWRCL_REG_OFFSET 0x0
+#define PERFCL_REG_OFFSET 0x80000
+#define MUX_OFFSET 0x40
+#define ALT_PLL_OFFSET 0x100
+#define SSSCTL_OFFSET 0x160
static const u8 prim_pll_regs[PLL_OFF_MAX_REGS] = {
[PLL_OFF_L_VAL] = 0x04,
@@ -107,7 +114,7 @@ enum _pmux_input {
};
static struct clk_alpha_pll perfcl_pll = {
- .offset = 0x80000,
+ .offset = PERFCL_REG_OFFSET,
.regs = prim_pll_regs,
.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
.clkr.hw.init = &(struct clk_init_data){
@@ -119,7 +126,7 @@ enum _pmux_input {
};
static struct clk_alpha_pll pwrcl_pll = {
- .offset = 0x0,
+ .offset = PWRCL_REG_OFFSET,
.regs = prim_pll_regs,
.flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
.clkr.hw.init = &(struct clk_init_data){
@@ -149,7 +156,7 @@ enum _pmux_input {
};
static struct clk_alpha_pll perfcl_alt_pll = {
- .offset = 0x80100,
+ .offset = PERFCL_REG_OFFSET + ALT_PLL_OFFSET,
.regs = alt_pll_regs,
.vco_table = alt_pll_vco_modes,
.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
@@ -163,7 +170,7 @@ enum _pmux_input {
};
static struct clk_alpha_pll pwrcl_alt_pll = {
- .offset = 0x100,
+ .offset = PWRCL_REG_OFFSET + ALT_PLL_OFFSET,
.regs = alt_pll_regs,
.vco_table = alt_pll_vco_modes,
.num_vco = ARRAY_SIZE(alt_pll_vco_modes),
@@ -176,6 +183,9 @@ enum _pmux_input {
},
};
+void __iomem *base;
+static void qcom_cpu_clk_msm8996_acd_init(void __iomem *base);
+
/* Mux'es */
struct clk_cpu_8996_mux {
@@ -253,6 +263,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
switch (event) {
case PRE_RATE_CHANGE:
ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
+ qcom_cpu_clk_msm8996_acd_init(base);
break;
case POST_RATE_CHANGE:
if (cnd->new_rate < DIV_2_THRESHOLD)
@@ -260,7 +271,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
DIV_2_INDEX);
else
ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
- PLL_INDEX);
+ ACD_INDEX);
break;
default:
ret = 0;
@@ -276,7 +287,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux pwrcl_smux = {
- .reg = 0x40,
+ .reg = PWRCL_REG_OFFSET + MUX_OFFSET,
.shift = 2,
.width = 2,
.clkr.hw.init = &(struct clk_init_data) {
@@ -292,7 +303,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux perfcl_smux = {
- .reg = 0x80040,
+ .reg = PERFCL_REG_OFFSET + MUX_OFFSET,
.shift = 2,
.width = 2,
.clkr.hw.init = &(struct clk_init_data) {
@@ -308,7 +319,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux pwrcl_pmux = {
- .reg = 0x40,
+ .reg = PWRCL_REG_OFFSET + MUX_OFFSET,
.shift = 0,
.width = 2,
.pll = &pwrcl_pll.clkr.hw,
@@ -329,7 +340,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
};
static struct clk_cpu_8996_mux perfcl_pmux = {
- .reg = 0x80040,
+ .reg = PERFCL_REG_OFFSET + MUX_OFFSET,
.shift = 0,
.width = 2,
.pll = &perfcl_pll.clkr.hw,
@@ -393,6 +404,10 @@ struct clk_regmap *clks[] = {
clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+ /* Enable alt PLLs */
+ clk_prepare_enable(pwrcl_alt_pll.clkr.hw.clk);
+ clk_prepare_enable(perfcl_alt_pll.clkr.hw.clk);
+
ret = clk_notifier_register(pwrcl_pmux.clkr.hw.clk, &pwrcl_pmux.nb);
if (ret)
return ret;
@@ -402,10 +417,48 @@ struct clk_regmap *clks[] = {
return ret;
}
+#define CPU_AFINITY_MASK 0xFFF
+#define PWRCL_CPU_REG_MASK 0x3
+#define PERFCL_CPU_REG_MASK 0x103
+
+#define L2ACDCR_REG 0x580ULL
+#define L2ACDTD_REG 0x581ULL
+#define L2ACDDVMRC_REG 0x584ULL
+#define L2ACDSSCR_REG 0x589ULL
+
+static DEFINE_SPINLOCK(acd_lock);
+
+static void qcom_cpu_clk_msm8996_acd_init(void __iomem *base)
+{
+ u64 hwid;
+ unsigned long flags;
+
+ spin_lock_irqsave(&acd_lock, flags);
+
+ hwid = read_cpuid_mpidr() & CPU_AFINITY_MASK;
+
+ kryo_l2_set_indirect_reg(L2ACDTD_REG, 0x00006A11);
+ kryo_l2_set_indirect_reg(L2ACDDVMRC_REG, 0x000E0F0F);
+ kryo_l2_set_indirect_reg(L2ACDSSCR_REG, 0x00000601);
+
+ if (PWRCL_CPU_REG_MASK == (hwid | PWRCL_CPU_REG_MASK)) {
+ writel(0xF, base + PWRCL_REG_OFFSET + SSSCTL_OFFSET);
+ wmb();
+ kryo_l2_set_indirect_reg(L2ACDCR_REG, 0x002C5FFD);
+ }
+
+ if (PERFCL_CPU_REG_MASK == (hwid | PERFCL_CPU_REG_MASK)) {
+ kryo_l2_set_indirect_reg(L2ACDCR_REG, 0x002C5FFD);
+ writel(0xF, base + PERFCL_REG_OFFSET + SSSCTL_OFFSET);
+ wmb();
+ }
+
+ spin_unlock_irqrestore(&acd_lock, flags);
+}
+
static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
{
int ret;
- void __iomem *base;
struct resource *res;
struct regmap *regmap;
struct clk_hw_onecell_data *data;
@@ -429,6 +482,8 @@ static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
if (ret)
return ret;
+ qcom_cpu_clk_msm8996_acd_init(base);
+
data->hws[0] = &pwrcl_pmux.clkr.hw;
data->hws[1] = &perfcl_pmux.clkr.hw;
data->num = 2;
--
1.9.1
^ permalink raw reply related
* [PATCH v8 07/15] clk: qcom: cpu-8996: Add support to switch below 600Mhz
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
The CPU clock controller's primary PLL operates on a single VCO range,
between 600MHz and 3GHz. However the CPUs do support OPPs with
frequencies between 300MHz and 600MHz. In order to support running the
CPUs at those frequencies we end up having to lock the PLL at twice the
rate and drive the CPU clk via the PLL/2 output and SMUX.
So for frequencies above 600MHz we follow the following path
Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300MHz and 600MHz we follow
Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 25 ++++++++++++++++++++++---
1 file changed, 22 insertions(+), 3 deletions(-)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index 620fdc2..ff5c0a5 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -68,6 +68,8 @@ enum _pmux_input {
NUM_OF_PMUX_INPUTS
};
+#define DIV_2_THRESHOLD 600000000
+
static const u8 prim_pll_regs[PLL_OFF_MAX_REGS] = {
[PLL_OFF_L_VAL] = 0x04,
[PLL_OFF_ALPHA_VAL] = 0x08,
@@ -95,10 +97,11 @@ enum _pmux_input {
static const struct alpha_pll_config hfpll_config = {
.l = 60,
- .config_ctl_val = 0x200d4828,
+ .config_ctl_val = 0x200d4aa8,
.config_ctl_hi_val = 0x006,
.pre_div_mask = BIT(12),
.post_div_mask = 0x3 << 8,
+ .post_div_val = 0x1 << 8,
.main_output_mask = BIT(0),
.early_output_mask = BIT(3),
};
@@ -140,7 +143,7 @@ enum _pmux_input {
.vco_mask = 0x3 << 20,
.config_ctl_val = 0x4001051b,
.post_div_mask = 0x3 << 8,
- .post_div_val = 0x1,
+ .post_div_val = 0x1 << 8,
.main_output_mask = BIT(0),
.early_output_mask = BIT(3),
};
@@ -181,6 +184,7 @@ struct clk_cpu_8996_mux {
u8 width;
struct notifier_block nb;
struct clk_hw *pll;
+ struct clk_hw *pll_div_2;
struct clk_regmap clkr;
};
@@ -226,6 +230,13 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
struct clk_hw *parent = cpuclk->pll;
+ if (cpuclk->pll_div_2 && req->rate < DIV_2_THRESHOLD) {
+ if (req->rate < (DIV_2_THRESHOLD / 2))
+ return -EINVAL;
+
+ parent = cpuclk->pll_div_2;
+ }
+
req->best_parent_rate = clk_hw_round_rate(parent, req->rate);
req->best_parent_hw = parent;
@@ -237,13 +248,19 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
{
int ret;
struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_nb(nb);
+ struct clk_notifier_data *cnd = data;
switch (event) {
case PRE_RATE_CHANGE:
ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
break;
case POST_RATE_CHANGE:
- ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, PLL_INDEX);
+ if (cnd->new_rate < DIV_2_THRESHOLD)
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
+ DIV_2_INDEX);
+ else
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw,
+ PLL_INDEX);
break;
default:
ret = 0;
@@ -295,6 +312,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
.shift = 0,
.width = 2,
.pll = &pwrcl_pll.clkr.hw,
+ .pll_div_2 = &pwrcl_smux.clkr.hw,
.nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "pwrcl_pmux",
@@ -315,6 +333,7 @@ int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
.shift = 0,
.width = 2,
.pll = &perfcl_pll.clkr.hw,
+ .pll_div_2 = &perfcl_smux.clkr.hw,
.nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "perfcl_pmux",
--
1.9.1
^ permalink raw reply related
* [PATCH v8 06/15] clk: qcom: cpu-8996: Add support to switch to alternate PLL
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
From: Rajendra Nayak <rnayak@codeaurora.org>
Each of the CPU clusters on msm8996 are powered via a primary
PLL and a secondary PLL. The primary PLL is what drives the
CPU clk, except for times when we are reprogramming the PLL
itself, when we temporarily switch to an alternate PLL.
Use clock rate change notifiers to support this.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-cpu-8996.c | 33 +++++++++++++++++++++++++++++++++
1 file changed, 33 insertions(+)
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
index d92cad93..620fdc2 100644
--- a/drivers/clk/qcom/clk-cpu-8996.c
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -52,6 +52,7 @@
* detect voltage droops.
*/
+#include <linux/clk.h>
#include <linux/module.h>
#include <linux/platform_device.h>
#include <linux/regmap.h>
@@ -178,10 +179,14 @@ struct clk_cpu_8996_mux {
u32 reg;
u8 shift;
u8 width;
+ struct notifier_block nb;
struct clk_hw *pll;
struct clk_regmap clkr;
};
+#define to_clk_cpu_8996_mux_nb(_nb) \
+ container_of(_nb, struct clk_cpu_8996_mux, nb)
+
static inline
struct clk_cpu_8996_mux *to_clk_cpu_8996_mux_hw(struct clk_hw *hw)
{
@@ -227,6 +232,26 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
return 0;
}
+int cpu_clk_notifier_cb(struct notifier_block *nb, unsigned long event,
+ void *data)
+{
+ int ret;
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_nb(nb);
+
+ switch (event) {
+ case PRE_RATE_CHANGE:
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, ALT_INDEX);
+ break;
+ case POST_RATE_CHANGE:
+ ret = clk_cpu_8996_mux_set_parent(&cpuclk->clkr.hw, PLL_INDEX);
+ break;
+ default:
+ ret = 0;
+ break;
+ }
+
+ return notifier_from_errno(ret);
+};
const struct clk_ops clk_cpu_8996_mux_ops = {
.set_parent = clk_cpu_8996_mux_set_parent,
.get_parent = clk_cpu_8996_mux_get_parent,
@@ -270,6 +295,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
.shift = 0,
.width = 2,
.pll = &pwrcl_pll.clkr.hw,
+ .nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "pwrcl_pmux",
.parent_names = (const char *[]){
@@ -289,6 +315,7 @@ static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
.shift = 0,
.width = 2,
.pll = &perfcl_pll.clkr.hw,
+ .nb.notifier_call = cpu_clk_notifier_cb,
.clkr.hw.init = &(struct clk_init_data) {
.name = "perfcl_pmux",
.parent_names = (const char *[]){
@@ -347,6 +374,12 @@ struct clk_regmap *clks[] = {
clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+ ret = clk_notifier_register(pwrcl_pmux.clkr.hw.clk, &pwrcl_pmux.nb);
+ if (ret)
+ return ret;
+
+ ret = clk_notifier_register(perfcl_pmux.clkr.hw.clk, &perfcl_pmux.nb);
+
return ret;
}
--
1.9.1
^ permalink raw reply related
* [PATCH v8 05/15] dt-bindings: clk: qcom: Add bindings for CPU clock for msm8996
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary and secondary all connected together
as shown below
+-------+
XO | |
+------------------>0 |
| |
PLL/2 | SMUX +----+
+------->1 | |
| | | |
| +-------+ | +-------+
| +---->0 |
| | |
+---------------+ | +----------->1 | CPU clk
|Primary PLL +----+ PLL_EARLY | | +------>
| +------+-----------+ +------>2 PMUX |
+---------------+ | | | |
| +------+ | +-->3 |
+--^+ ACD +-----+ | +-------+
+---------------+ +------+ |
|Alt PLL | |
| +---------------------------+
+---------------+ PLL_EARLY
The primary PLL is what drives the CPU clk, except for times
when we are reprogramming the PLL itself (for rate changes) when
we temporarily switch to an alternate PLL. A subsequent patch adds
support to switch between primary and alternate PLL during rate
changes.
The primary PLL operates on a single VCO range, between 600MHz
and 3GHz. However the CPUs do support OPPs with frequencies
between 300MHz and 600MHz. In order to support running the CPUs
at those frequencies we end up having to lock the PLL at twice
the rate and drive the CPU clk via the PLL/2 output and SMUX.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/clock/qcom,kryocc.txt | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
create mode 100644 Documentation/devicetree/bindings/clock/qcom,kryocc.txt
diff --git a/Documentation/devicetree/bindings/clock/qcom,kryocc.txt b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
new file mode 100644
index 0000000..8458783
--- /dev/null
+++ b/Documentation/devicetree/bindings/clock/qcom,kryocc.txt
@@ -0,0 +1,17 @@
+Qualcomm CPUSS clock controller for Kryo CPUs
+----------------------------------------------------
+
+Required properties :
+- compatible : shall contain only one of the following:
+
+ "qcom,msm8996-apcc"
+
+- reg : shall contain base register location and length
+- #clock-cells : shall contain 1
+
+Example:
+ kryocc: clock-controller at 6400000 {
+ compatible = "qcom,msm8996-apcc";
+ reg = <0x6400000 0x90000>;
+ #clock-cells = <1>;
+ };
--
1.9.1
^ permalink raw reply related
* [PATCH v8 04/15] clk: qcom: Add CPU clock driver for msm8996
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary and secondary all connected together
as shown below
+-------+
XO | |
+------------------>0 |
| |
PLL/2 | SMUX +----+
+------->1 | |
| | | |
| +-------+ | +-------+
| +---->0 |
| | |
+---------------+ | +----------->1 | CPU clk
|Primary PLL +----+ PLL_EARLY | | +------>
| +------+-----------+ +------>2 PMUX |
+---------------+ | | | |
| +------+ | +-->3 |
+--^+ ACD +-----+ | +-------+
+---------------+ +------+ |
|Alt PLL | |
| +---------------------------+
+---------------+ PLL_EARLY
The primary PLL is what drives the CPU clk, except for times
when we are reprogramming the PLL itself (for rate changes) when
we temporarily switch to an alternate PLL. A subsequent patch adds
support to switch between primary and alternate PLL during rate
changes.
The primary PLL operates on a single VCO range, between 600MHz
and 3GHz. However the CPUs do support OPPs with frequencies
between 300MHz and 600MHz. In order to support running the CPUs
at those frequencies we end up having to lock the PLL at twice
the rate and drive the CPU clk via the PLL/2 output and SMUX.
So for frequencies above 600MHz we follow the following path
Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300MHz and 600MHz we follow
Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
Support for this is added in a subsequent patch as well.
ACD stands for Adaptive Clock Distribution and is used to
detect voltage droops.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/Kconfig | 9 +
drivers/clk/qcom/Makefile | 1 +
drivers/clk/qcom/clk-alpha-pll.h | 6 +
drivers/clk/qcom/clk-cpu-8996.c | 403 +++++++++++++++++++++++++++++++++++++++
4 files changed, 419 insertions(+)
create mode 100644 drivers/clk/qcom/clk-cpu-8996.c
diff --git a/drivers/clk/qcom/Kconfig b/drivers/clk/qcom/Kconfig
index e42e1af..866ce1f 100644
--- a/drivers/clk/qcom/Kconfig
+++ b/drivers/clk/qcom/Kconfig
@@ -33,6 +33,15 @@ config QCOM_CLK_APCS_MSM8916
Say Y if you want to support CPU frequency scaling on devices
such as msm8916.
+config QCOM_CLK_APCC_MSM8996
+ tristate "MSM8996 CPU Clock Controller"
+ depends on COMMON_CLK_QCOM
+ select QCOM_KRYO_L2_ACCESSORS
+ help
+ Support for the CPU clock controller on msm8996 devices.
+ Say Y if you want to support CPU clock scaling using CPUfreq
+ drivers for dyanmic power management.
+
config QCOM_CLK_RPM
tristate "RPM based Clock Controller"
depends on COMMON_CLK_QCOM && MFD_QCOM_RPM
diff --git a/drivers/clk/qcom/Makefile b/drivers/clk/qcom/Makefile
index 7c09ab1..a822fc8 100644
--- a/drivers/clk/qcom/Makefile
+++ b/drivers/clk/qcom/Makefile
@@ -36,6 +36,7 @@ obj-$(CONFIG_MSM_MMCC_8974) += mmcc-msm8974.o
obj-$(CONFIG_MSM_MMCC_8996) += mmcc-msm8996.o
obj-$(CONFIG_QCOM_A53PLL) += a53-pll.o
obj-$(CONFIG_QCOM_CLK_APCS_MSM8916) += apcs-msm8916.o
+obj-$(CONFIG_QCOM_CLK_APCC_MSM8996) += clk-cpu-8996.o
obj-$(CONFIG_QCOM_CLK_RPM) += clk-rpm.o
obj-$(CONFIG_QCOM_CLK_SMD_RPM) += clk-smd-rpm.o
obj-$(CONFIG_SPMI_PMIC_CLKDIV) += clk-spmi-pmic-div.o
diff --git a/drivers/clk/qcom/clk-alpha-pll.h b/drivers/clk/qcom/clk-alpha-pll.h
index f981b48..9ce2a32 100644
--- a/drivers/clk/qcom/clk-alpha-pll.h
+++ b/drivers/clk/qcom/clk-alpha-pll.h
@@ -50,6 +50,12 @@ struct pll_vco {
u32 val;
};
+#define VCO(a, b, c) { \
+ .val = a,\
+ .min_freq = b,\
+ .max_freq = c,\
+}
+
/**
* struct clk_alpha_pll - phase locked loop (PLL)
* @offset: base address of registers
diff --git a/drivers/clk/qcom/clk-cpu-8996.c b/drivers/clk/qcom/clk-cpu-8996.c
new file mode 100644
index 0000000..d92cad93
--- /dev/null
+++ b/drivers/clk/qcom/clk-cpu-8996.c
@@ -0,0 +1,403 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+/*
+ * Each of the CPU clusters (Power and Perf) on msm8996 are
+ * clocked via 2 PLLs, a primary and alternate. There are also
+ * 2 Mux'es, a primary and secondary all connected together
+ * as shown below
+ *
+ * +-------+
+ * XO | |
+ * +------------------>0 |
+ * | |
+ * PLL/2 | SMUX +----+
+ * +------->1 | |
+ * | | | |
+ * | +-------+ | +-------+
+ * | +---->0 |
+ * | | |
+ * +---------------+ | +----------->1 | CPU clk
+ * |Primary PLL +----+ PLL_EARLY | | +------>
+ * | +------+-----------+ +------>2 PMUX |
+ * +---------------+ | | | |
+ * | +------+ | +-->3 |
+ * +--^+ ACD +-----+ | +-------+
+ * +---------------+ +------+ |
+ * |Alt PLL | |
+ * | +---------------------------+
+ * +---------------+ PLL_EARLY
+ *
+ * The primary PLL is what drives the CPU clk, except for times
+ * when we are reprogramming the PLL itself (for rate changes) when
+ * we temporarily switch to an alternate PLL. A subsequent patch adds
+ * support to switch between primary and alternate PLL during rate
+ * changes.
+ *
+ * The primary PLL operates on a single VCO range, between 600MHz
+ * and 3GHz. However the CPUs do support OPPs with frequencies
+ * between 300MHz and 600MHz. In order to support running the CPUs
+ * at those frequencies we end up having to lock the PLL at twice
+ * the rate and drive the CPU clk via the PLL/2 output and SMUX.
+ *
+ * So for frequencies above 600MHz we follow the following path
+ * Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
+ * and for frequencies between 300MHz and 600MHz we follow
+ * Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk
+ * Support for this is added in a subsequent patch as well.
+ *
+ * ACD stands for Adaptive Clock Distribution and is used to
+ * detect voltage droops.
+ */
+
+#include <linux/module.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "clk-alpha-pll.h"
+#include "clk-regmap.h"
+
+enum _pmux_input {
+ DIV_2_INDEX = 0,
+ PLL_INDEX,
+ ACD_INDEX,
+ ALT_INDEX,
+ NUM_OF_PMUX_INPUTS
+};
+
+static const u8 prim_pll_regs[PLL_OFF_MAX_REGS] = {
+ [PLL_OFF_L_VAL] = 0x04,
+ [PLL_OFF_ALPHA_VAL] = 0x08,
+ [PLL_OFF_USER_CTL] = 0x10,
+ [PLL_OFF_CONFIG_CTL] = 0x18,
+ [PLL_OFF_CONFIG_CTL_U] = 0x1c,
+ [PLL_OFF_TEST_CTL] = 0x20,
+ [PLL_OFF_TEST_CTL_U] = 0x24,
+ [PLL_OFF_STATUS] = 0x28,
+};
+
+static const u8 alt_pll_regs[PLL_OFF_MAX_REGS] = {
+ [PLL_OFF_L_VAL] = 0x04,
+ [PLL_OFF_ALPHA_VAL] = 0x08,
+ [PLL_OFF_ALPHA_VAL_U] = 0x0c,
+ [PLL_OFF_USER_CTL] = 0x10,
+ [PLL_OFF_USER_CTL_U] = 0x14,
+ [PLL_OFF_CONFIG_CTL] = 0x18,
+ [PLL_OFF_TEST_CTL] = 0x20,
+ [PLL_OFF_TEST_CTL_U] = 0x24,
+ [PLL_OFF_STATUS] = 0x28,
+};
+
+/* PLLs */
+
+static const struct alpha_pll_config hfpll_config = {
+ .l = 60,
+ .config_ctl_val = 0x200d4828,
+ .config_ctl_hi_val = 0x006,
+ .pre_div_mask = BIT(12),
+ .post_div_mask = 0x3 << 8,
+ .main_output_mask = BIT(0),
+ .early_output_mask = BIT(3),
+};
+
+static struct clk_alpha_pll perfcl_pll = {
+ .offset = 0x80000,
+ .regs = prim_pll_regs,
+ .flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "perfcl_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_huayra_ops,
+ },
+};
+
+static struct clk_alpha_pll pwrcl_pll = {
+ .offset = 0x0,
+ .regs = prim_pll_regs,
+ .flags = SUPPORTS_DYNAMIC_UPDATE | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data){
+ .name = "pwrcl_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_huayra_ops,
+ },
+};
+
+static const struct pll_vco alt_pll_vco_modes[] = {
+ VCO(3, 250000000, 500000000),
+ VCO(2, 500000000, 750000000),
+ VCO(1, 750000000, 1000000000),
+ VCO(0, 1000000000, 2150400000),
+};
+
+static const struct alpha_pll_config altpll_config = {
+ .l = 16,
+ .vco_val = 0x3 << 20,
+ .vco_mask = 0x3 << 20,
+ .config_ctl_val = 0x4001051b,
+ .post_div_mask = 0x3 << 8,
+ .post_div_val = 0x1,
+ .main_output_mask = BIT(0),
+ .early_output_mask = BIT(3),
+};
+
+static struct clk_alpha_pll perfcl_alt_pll = {
+ .offset = 0x80100,
+ .regs = alt_pll_regs,
+ .vco_table = alt_pll_vco_modes,
+ .num_vco = ARRAY_SIZE(alt_pll_vco_modes),
+ .flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "perfcl_alt_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_hwfsm_ops,
+ },
+};
+
+static struct clk_alpha_pll pwrcl_alt_pll = {
+ .offset = 0x100,
+ .regs = alt_pll_regs,
+ .vco_table = alt_pll_vco_modes,
+ .num_vco = ARRAY_SIZE(alt_pll_vco_modes),
+ .flags = SUPPORTS_OFFLINE_REQ | SUPPORTS_FSM_MODE,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "pwrcl_alt_pll",
+ .parent_names = (const char *[]){ "xo" },
+ .num_parents = 1,
+ .ops = &clk_alpha_pll_hwfsm_ops,
+ },
+};
+
+/* Mux'es */
+
+struct clk_cpu_8996_mux {
+ u32 reg;
+ u8 shift;
+ u8 width;
+ struct clk_hw *pll;
+ struct clk_regmap clkr;
+};
+
+static inline
+struct clk_cpu_8996_mux *to_clk_cpu_8996_mux_hw(struct clk_hw *hw)
+{
+ return container_of(to_clk_regmap(hw), struct clk_cpu_8996_mux, clkr);
+}
+
+static u8 clk_cpu_8996_mux_get_parent(struct clk_hw *hw)
+{
+ u32 val;
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+ u32 mask = (u32)GENMASK(cpuclk->width - 1, 0);
+
+ regmap_read(clkr->regmap, cpuclk->reg, &val);
+ val >>= (u32)(cpuclk->shift);
+
+ return (u8)(val & mask);
+}
+
+static int clk_cpu_8996_mux_set_parent(struct clk_hw *hw, u8 index)
+{
+ u32 val;
+ struct clk_regmap *clkr = to_clk_regmap(hw);
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+ unsigned int mask = GENMASK(cpuclk->width + cpuclk->shift - 1,
+ cpuclk->shift);
+
+ val = (u32)index;
+ val <<= (u32)(cpuclk->shift);
+
+ return regmap_update_bits(clkr->regmap, cpuclk->reg, mask, val);
+}
+
+static int
+clk_cpu_8996_mux_determine_rate(struct clk_hw *hw, struct clk_rate_request *req)
+{
+ struct clk_cpu_8996_mux *cpuclk = to_clk_cpu_8996_mux_hw(hw);
+ struct clk_hw *parent = cpuclk->pll;
+
+ req->best_parent_rate = clk_hw_round_rate(parent, req->rate);
+ req->best_parent_hw = parent;
+
+ return 0;
+}
+
+const struct clk_ops clk_cpu_8996_mux_ops = {
+ .set_parent = clk_cpu_8996_mux_set_parent,
+ .get_parent = clk_cpu_8996_mux_get_parent,
+ .determine_rate = clk_cpu_8996_mux_determine_rate,
+};
+
+static struct clk_cpu_8996_mux pwrcl_smux = {
+ .reg = 0x40,
+ .shift = 2,
+ .width = 2,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "pwrcl_smux",
+ .parent_names = (const char *[]){
+ "xo",
+ "pwrcl_pll_main",
+ },
+ .num_parents = 2,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_cpu_8996_mux perfcl_smux = {
+ .reg = 0x80040,
+ .shift = 2,
+ .width = 2,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "perfcl_smux",
+ .parent_names = (const char *[]){
+ "xo",
+ "perfcl_pll_main",
+ },
+ .num_parents = 2,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT,
+ },
+};
+
+static struct clk_cpu_8996_mux pwrcl_pmux = {
+ .reg = 0x40,
+ .shift = 0,
+ .width = 2,
+ .pll = &pwrcl_pll.clkr.hw,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "pwrcl_pmux",
+ .parent_names = (const char *[]){
+ "pwrcl_smux",
+ "pwrcl_pll",
+ "pwrcl_pll_acd",
+ "pwrcl_alt_pll",
+ },
+ .num_parents = 4,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static struct clk_cpu_8996_mux perfcl_pmux = {
+ .reg = 0x80040,
+ .shift = 0,
+ .width = 2,
+ .pll = &perfcl_pll.clkr.hw,
+ .clkr.hw.init = &(struct clk_init_data) {
+ .name = "perfcl_pmux",
+ .parent_names = (const char *[]){
+ "perfcl_smux",
+ "perfcl_pll",
+ "perfcl_pll_acd",
+ "perfcl_alt_pll",
+ },
+ .num_parents = 4,
+ .ops = &clk_cpu_8996_mux_ops,
+ .flags = CLK_SET_RATE_PARENT | CLK_IGNORE_UNUSED,
+ },
+};
+
+static const struct regmap_config cpu_msm8996_regmap_config = {
+ .reg_bits = 32,
+ .reg_stride = 4,
+ .val_bits = 32,
+ .max_register = 0x80210,
+ .fast_io = true,
+ .val_format_endian = REGMAP_ENDIAN_LITTLE,
+};
+
+struct clk_regmap *clks[] = {
+ &perfcl_pll.clkr,
+ &pwrcl_pll.clkr,
+ &perfcl_alt_pll.clkr,
+ &pwrcl_alt_pll.clkr,
+ &perfcl_smux.clkr,
+ &pwrcl_smux.clkr,
+ &perfcl_pmux.clkr,
+ &pwrcl_pmux.clkr,
+};
+
+static int
+qcom_cpu_clk_msm8996_register_clks(struct device *dev, struct regmap *regmap)
+{
+ int i, ret;
+
+ perfcl_smux.pll = clk_hw_register_fixed_factor(dev, "perfcl_pll_main",
+ "perfcl_pll",
+ CLK_SET_RATE_PARENT, 1, 2);
+
+ pwrcl_smux.pll = clk_hw_register_fixed_factor(dev, "pwrcl_pll_main",
+ "pwrcl_pll",
+ CLK_SET_RATE_PARENT, 1, 2);
+
+ for (i = 0; i < ARRAY_SIZE(clks); i++) {
+ ret = devm_clk_register_regmap(dev, clks[i]);
+ if (ret)
+ return ret;
+ }
+
+ clk_alpha_pll_configure(&perfcl_pll, regmap, &hfpll_config);
+ clk_alpha_pll_configure(&pwrcl_pll, regmap, &hfpll_config);
+ clk_alpha_pll_configure(&perfcl_alt_pll, regmap, &altpll_config);
+ clk_alpha_pll_configure(&pwrcl_alt_pll, regmap, &altpll_config);
+
+ return ret;
+}
+
+static int qcom_cpu_clk_msm8996_driver_probe(struct platform_device *pdev)
+{
+ int ret;
+ void __iomem *base;
+ struct resource *res;
+ struct regmap *regmap;
+ struct clk_hw_onecell_data *data;
+ struct device *dev = &pdev->dev;
+
+ data = devm_kzalloc(dev, sizeof(*data) + 2 * sizeof(struct clk_hw *),
+ GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+ base = devm_ioremap_resource(dev, res);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ regmap = devm_regmap_init_mmio(dev, base, &cpu_msm8996_regmap_config);
+ if (IS_ERR(regmap))
+ return PTR_ERR(regmap);
+
+ ret = qcom_cpu_clk_msm8996_register_clks(dev, regmap);
+ if (ret)
+ return ret;
+
+ data->hws[0] = &pwrcl_pmux.clkr.hw;
+ data->hws[1] = &perfcl_pmux.clkr.hw;
+ data->num = 2;
+
+ return devm_of_clk_add_hw_provider(dev, of_clk_hw_onecell_get, data);
+}
+
+static const struct of_device_id qcom_cpu_clk_msm8996_match_table[] = {
+ { .compatible = "qcom,msm8996-apcc" },
+ {}
+};
+
+static struct platform_driver qcom_cpu_clk_msm8996_driver = {
+ .probe = qcom_cpu_clk_msm8996_driver_probe,
+ .driver = {
+ .name = "qcom-msm8996-apcc",
+ .of_match_table = qcom_cpu_clk_msm8996_match_table,
+ },
+};
+module_platform_driver(qcom_cpu_clk_msm8996_driver);
+
+MODULE_ALIAS("platform:msm8996-apcc");
+MODULE_DESCRIPTION("QCOM MSM8996 CPU Clock Driver");
+MODULE_LICENSE("GPL v2");
--
1.9.1
^ permalink raw reply related
* [PATCH v8 03/15] clk: Use devm_ in the register fixed factor clock
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
Use devm_clk_hw_register instead of clk_hw_register
to simplify the usage of this API. This way drivers that call
the clk_hw_register_fixed_factor won't need to maintain
a data structure for further cleanup.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/clk-fixed-factor.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/clk/clk-fixed-factor.c b/drivers/clk/clk-fixed-factor.c
index a5d402d..8e39bda 100644
--- a/drivers/clk/clk-fixed-factor.c
+++ b/drivers/clk/clk-fixed-factor.c
@@ -94,7 +94,7 @@ struct clk_hw *clk_hw_register_fixed_factor(struct device *dev,
init.num_parents = 1;
hw = &fix->hw;
- ret = clk_hw_register(dev, hw);
+ ret = devm_clk_hw_register(dev, hw);
if (ret) {
kfree(fix);
hw = ERR_PTR(ret);
--
1.9.1
^ permalink raw reply related
* [PATCH v8 02/15] clk: qcom: Make clk_alpha_pll_configure available to modules
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
From: Rajendra Nayak <rnayak@codeaurora.org>
Allow clk_alpha_pll_configure to be called from loadable
kernel modules.
Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/clk/qcom/clk-alpha-pll.c | 1 +
1 file changed, 1 insertion(+)
diff --git a/drivers/clk/qcom/clk-alpha-pll.c b/drivers/clk/qcom/clk-alpha-pll.c
index 9722b70..57f2084 100644
--- a/drivers/clk/qcom/clk-alpha-pll.c
+++ b/drivers/clk/qcom/clk-alpha-pll.c
@@ -228,6 +228,7 @@ void clk_alpha_pll_configure(struct clk_alpha_pll *pll, struct regmap *regmap,
if (pll->flags & SUPPORTS_FSM_MODE)
qcom_pll_set_fsm_mode(regmap, PLL_MODE(pll), 6, 0);
}
+EXPORT_SYMBOL_GPL(clk_alpha_pll_configure);
static int clk_alpha_pll_hwfsm_enable(struct clk_hw *hw)
{
--
1.9.1
^ permalink raw reply related
* [PATCH v8 01/15] soc: qcom: Separate kryo l2 accessors from PMU driver
From: Ilia Lin @ 2018-05-17 11:19 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526555955-29960-1-git-send-email-ilialin@codeaurora.org>
The driver provides kernel level API for other drivers
to access the MSM8996 L2 cache registers.
Separating the L2 access code from the PMU driver and
making it public to allow other drivers use it.
The accesses must be separated with a single spinlock,
maintained in this driver.
Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
---
drivers/perf/Kconfig | 1 +
drivers/perf/qcom_l2_pmu.c | 90 ++++++++++--------------------------
drivers/soc/qcom/Kconfig | 3 ++
drivers/soc/qcom/Makefile | 1 +
drivers/soc/qcom/kryo-l2-accessors.c | 56 ++++++++++++++++++++++
include/soc/qcom/kryo-l2-accessors.h | 12 +++++
6 files changed, 97 insertions(+), 66 deletions(-)
create mode 100644 drivers/soc/qcom/kryo-l2-accessors.c
create mode 100644 include/soc/qcom/kryo-l2-accessors.h
diff --git a/drivers/perf/Kconfig b/drivers/perf/Kconfig
index 28bb5a0..561252a 100644
--- a/drivers/perf/Kconfig
+++ b/drivers/perf/Kconfig
@@ -69,6 +69,7 @@ config HISI_PMU
config QCOM_L2_PMU
bool "Qualcomm Technologies L2-cache PMU"
depends on ARCH_QCOM && ARM64 && ACPI
+ select QCOM_KRYO_L2_ACCESSORS
help
Provides support for the L2 cache performance monitor unit (PMU)
in Qualcomm Technologies processors.
diff --git a/drivers/perf/qcom_l2_pmu.c b/drivers/perf/qcom_l2_pmu.c
index 842135c..cc31f51 100644
--- a/drivers/perf/qcom_l2_pmu.c
+++ b/drivers/perf/qcom_l2_pmu.c
@@ -31,6 +31,7 @@
#include <asm/barrier.h>
#include <asm/local64.h>
#include <asm/sysreg.h>
+#include <soc/qcom/kryo-l2-accessors.h>
#define MAX_L2_CTRS 9
@@ -87,8 +88,6 @@
#define L2_COUNTER_RELOAD BIT_ULL(31)
#define L2_CYCLE_COUNTER_RELOAD BIT_ULL(63)
-#define L2CPUSRSELR_EL1 sys_reg(3, 3, 15, 0, 6)
-#define L2CPUSRDR_EL1 sys_reg(3, 3, 15, 0, 7)
#define reg_idx(reg, i) (((i) * IA_L2_REG_OFFSET) + reg##_BASE)
@@ -107,48 +106,7 @@
#define L2_EVENT_STREX 0x421
#define L2_EVENT_CLREX 0x422
-static DEFINE_RAW_SPINLOCK(l2_access_lock);
-/**
- * set_l2_indirect_reg: write value to an L2 register
- * @reg: Address of L2 register.
- * @value: Value to be written to register.
- *
- * Use architecturally required barriers for ordering between system register
- * accesses
- */
-static void set_l2_indirect_reg(u64 reg, u64 val)
-{
- unsigned long flags;
-
- raw_spin_lock_irqsave(&l2_access_lock, flags);
- write_sysreg_s(reg, L2CPUSRSELR_EL1);
- isb();
- write_sysreg_s(val, L2CPUSRDR_EL1);
- isb();
- raw_spin_unlock_irqrestore(&l2_access_lock, flags);
-}
-
-/**
- * get_l2_indirect_reg: read an L2 register value
- * @reg: Address of L2 register.
- *
- * Use architecturally required barriers for ordering between system register
- * accesses
- */
-static u64 get_l2_indirect_reg(u64 reg)
-{
- u64 val;
- unsigned long flags;
-
- raw_spin_lock_irqsave(&l2_access_lock, flags);
- write_sysreg_s(reg, L2CPUSRSELR_EL1);
- isb();
- val = read_sysreg_s(L2CPUSRDR_EL1);
- raw_spin_unlock_irqrestore(&l2_access_lock, flags);
-
- return val;
-}
struct cluster_pmu;
@@ -219,28 +177,28 @@ static inline struct cluster_pmu *get_cluster_pmu(
static void cluster_pmu_reset(void)
{
/* Reset all counters */
- set_l2_indirect_reg(L2PMCR, L2PMCR_RESET_ALL);
- set_l2_indirect_reg(L2PMCNTENCLR, l2_counter_present_mask);
- set_l2_indirect_reg(L2PMINTENCLR, l2_counter_present_mask);
- set_l2_indirect_reg(L2PMOVSCLR, l2_counter_present_mask);
+ kryo_l2_set_indirect_reg(L2PMCR, L2PMCR_RESET_ALL);
+ kryo_l2_set_indirect_reg(L2PMCNTENCLR, l2_counter_present_mask);
+ kryo_l2_set_indirect_reg(L2PMINTENCLR, l2_counter_present_mask);
+ kryo_l2_set_indirect_reg(L2PMOVSCLR, l2_counter_present_mask);
}
static inline void cluster_pmu_enable(void)
{
- set_l2_indirect_reg(L2PMCR, L2PMCR_COUNTERS_ENABLE);
+ kryo_l2_set_indirect_reg(L2PMCR, L2PMCR_COUNTERS_ENABLE);
}
static inline void cluster_pmu_disable(void)
{
- set_l2_indirect_reg(L2PMCR, L2PMCR_COUNTERS_DISABLE);
+ kryo_l2_set_indirect_reg(L2PMCR, L2PMCR_COUNTERS_DISABLE);
}
static inline void cluster_pmu_counter_set_value(u32 idx, u64 value)
{
if (idx == l2_cycle_ctr_idx)
- set_l2_indirect_reg(L2PMCCNTR, value);
+ kryo_l2_set_indirect_reg(L2PMCCNTR, value);
else
- set_l2_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx), value);
+ kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx), value);
}
static inline u64 cluster_pmu_counter_get_value(u32 idx)
@@ -248,46 +206,46 @@ static inline u64 cluster_pmu_counter_get_value(u32 idx)
u64 value;
if (idx == l2_cycle_ctr_idx)
- value = get_l2_indirect_reg(L2PMCCNTR);
+ value = kryo_l2_get_indirect_reg(L2PMCCNTR);
else
- value = get_l2_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx));
+ value = kryo_l2_get_indirect_reg(reg_idx(IA_L2PMXEVCNTR, idx));
return value;
}
static inline void cluster_pmu_counter_enable(u32 idx)
{
- set_l2_indirect_reg(L2PMCNTENSET, idx_to_reg_bit(idx));
+ kryo_l2_set_indirect_reg(L2PMCNTENSET, idx_to_reg_bit(idx));
}
static inline void cluster_pmu_counter_disable(u32 idx)
{
- set_l2_indirect_reg(L2PMCNTENCLR, idx_to_reg_bit(idx));
+ kryo_l2_set_indirect_reg(L2PMCNTENCLR, idx_to_reg_bit(idx));
}
static inline void cluster_pmu_counter_enable_interrupt(u32 idx)
{
- set_l2_indirect_reg(L2PMINTENSET, idx_to_reg_bit(idx));
+ kryo_l2_set_indirect_reg(L2PMINTENSET, idx_to_reg_bit(idx));
}
static inline void cluster_pmu_counter_disable_interrupt(u32 idx)
{
- set_l2_indirect_reg(L2PMINTENCLR, idx_to_reg_bit(idx));
+ kryo_l2_set_indirect_reg(L2PMINTENCLR, idx_to_reg_bit(idx));
}
static inline void cluster_pmu_set_evccntcr(u32 val)
{
- set_l2_indirect_reg(L2PMCCNTCR, val);
+ kryo_l2_set_indirect_reg(L2PMCCNTCR, val);
}
static inline void cluster_pmu_set_evcntcr(u32 ctr, u32 val)
{
- set_l2_indirect_reg(reg_idx(IA_L2PMXEVCNTCR, ctr), val);
+ kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVCNTCR, ctr), val);
}
static inline void cluster_pmu_set_evtyper(u32 ctr, u32 val)
{
- set_l2_indirect_reg(reg_idx(IA_L2PMXEVTYPER, ctr), val);
+ kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVTYPER, ctr), val);
}
static void cluster_pmu_set_resr(struct cluster_pmu *cluster,
@@ -303,11 +261,11 @@ static void cluster_pmu_set_resr(struct cluster_pmu *cluster,
spin_lock_irqsave(&cluster->pmu_lock, flags);
- resr_val = get_l2_indirect_reg(L2PMRESR);
+ resr_val = kryo_l2_get_indirect_reg(L2PMRESR);
resr_val &= ~(L2PMRESR_GROUP_MASK << shift);
resr_val |= field;
resr_val |= L2PMRESR_EN;
- set_l2_indirect_reg(L2PMRESR, resr_val);
+ kryo_l2_set_indirect_reg(L2PMRESR, resr_val);
spin_unlock_irqrestore(&cluster->pmu_lock, flags);
}
@@ -323,14 +281,14 @@ static inline void cluster_pmu_set_evfilter_sys_mode(u32 ctr)
L2PMXEVFILTER_ORGFILTER_IDINDEP |
L2PMXEVFILTER_ORGFILTER_ALL;
- set_l2_indirect_reg(reg_idx(IA_L2PMXEVFILTER, ctr), val);
+ kryo_l2_set_indirect_reg(reg_idx(IA_L2PMXEVFILTER, ctr), val);
}
static inline u32 cluster_pmu_getreset_ovsr(void)
{
- u32 result = get_l2_indirect_reg(L2PMOVSSET);
+ u32 result = kryo_l2_get_indirect_reg(L2PMOVSSET);
- set_l2_indirect_reg(L2PMOVSCLR, result);
+ kryo_l2_set_indirect_reg(L2PMOVSCLR, result);
return result;
}
@@ -783,7 +741,7 @@ static int get_num_counters(void)
{
int val;
- val = get_l2_indirect_reg(L2PMCR);
+ val = kryo_l2_get_indirect_reg(L2PMCR);
/*
* Read number of counters from L2PMCR and add 1
diff --git a/drivers/soc/qcom/Kconfig b/drivers/soc/qcom/Kconfig
index 7093fe7..0567dff 100644
--- a/drivers/soc/qcom/Kconfig
+++ b/drivers/soc/qcom/Kconfig
@@ -39,6 +39,9 @@ config QCOM_GSBI
functions for connecting the underlying serial UART, SPI, and I2C
devices to the output pins.
+config QCOM_KRYO_L2_ACCESSORS
+ bool
+
config QCOM_MDT_LOADER
tristate
select QCOM_SCM
diff --git a/drivers/soc/qcom/Makefile b/drivers/soc/qcom/Makefile
index cbf414c..e4d3f5a 100644
--- a/drivers/soc/qcom/Makefile
+++ b/drivers/soc/qcom/Makefile
@@ -14,3 +14,4 @@ obj-$(CONFIG_QCOM_SMEM_STATE) += smem_state.o
obj-$(CONFIG_QCOM_SMP2P) += smp2p.o
obj-$(CONFIG_QCOM_SMSM) += smsm.o
obj-$(CONFIG_QCOM_WCNSS_CTRL) += wcnss_ctrl.o
+obj-$(CONFIG_QCOM_KRYO_L2_ACCESSORS) += kryo-l2-accessors.o
diff --git a/drivers/soc/qcom/kryo-l2-accessors.c b/drivers/soc/qcom/kryo-l2-accessors.c
new file mode 100644
index 0000000..75fd07a
--- /dev/null
+++ b/drivers/soc/qcom/kryo-l2-accessors.c
@@ -0,0 +1,56 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#include <linux/spinlock.h>
+#include <asm/sysreg.h>
+#include <soc/qcom/kryo-l2-accessors.h>
+
+#define L2CPUSRSELR_EL1 sys_reg(3, 3, 15, 0, 6)
+#define L2CPUSRDR_EL1 sys_reg(3, 3, 15, 0, 7)
+
+static DEFINE_RAW_SPINLOCK(l2_access_lock);
+
+/**
+ * kryo_l2_set_indirect_reg() - write value to an L2 register
+ * @reg: Address of L2 register.
+ * @value: Value to be written to register.
+ *
+ * Use architecturally required barriers for ordering between system register
+ * accesses, and system registers with respect to device memory
+ */
+void kryo_l2_set_indirect_reg(u64 reg, u64 val)
+{
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&l2_access_lock, flags);
+ write_sysreg_s(reg, L2CPUSRSELR_EL1);
+ isb();
+ write_sysreg_s(val, L2CPUSRDR_EL1);
+ isb();
+ raw_spin_unlock_irqrestore(&l2_access_lock, flags);
+}
+EXPORT_SYMBOL(kryo_l2_set_indirect_reg);
+
+/**
+ * kryo_l2_get_indirect_reg() - read an L2 register value
+ * @reg: Address of L2 register.
+ *
+ * Use architecturally required barriers for ordering between system register
+ * accesses, and system registers with respect to device memory
+ */
+u64 kryo_l2_get_indirect_reg(u64 reg)
+{
+ u64 val;
+ unsigned long flags;
+
+ raw_spin_lock_irqsave(&l2_access_lock, flags);
+ write_sysreg_s(reg, L2CPUSRSELR_EL1);
+ isb();
+ val = read_sysreg_s(L2CPUSRDR_EL1);
+ raw_spin_unlock_irqrestore(&l2_access_lock, flags);
+
+ return val;
+}
+EXPORT_SYMBOL(kryo_l2_get_indirect_reg);
diff --git a/include/soc/qcom/kryo-l2-accessors.h b/include/soc/qcom/kryo-l2-accessors.h
new file mode 100644
index 0000000..673c534
--- /dev/null
+++ b/include/soc/qcom/kryo-l2-accessors.h
@@ -0,0 +1,12 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2018, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef __SOC_ARCH_QCOM_KRYO_L2_ACCESSORS_H
+#define __SOC_ARCH_QCOM_KRYO_L2_ACCESSORS_H
+
+void kryo_l2_set_indirect_reg(u64 reg, u64 val);
+u64 kryo_l2_get_indirect_reg(u64 reg);
+
+#endif
--
1.9.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox