* [PATCH v6 5/5] drm/rockchip: support dp training outside dp firmware
From: Lin Huang @ 2018-05-21 9:37 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526895424-22894-1-git-send-email-hl@rock-chips.com>
DP firmware uses fixed phy config values to do training, but some
boards need to adjust these values to fit for their unique hardware
design. So get phy config values from dts and use software link training
instead of relying on firmware, if software training fail, keep firmware
training as a fallback if sw training fails.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
---
Changes in v2:
- update patch following Enric suggest
Changes in v3:
- use variable fw_training instead sw_training_success
- base on DP SPCE, if training fail use lower link rate to retry training
Changes in v4:
- improve cdn_dp_get_lower_link_rate() and cdn_dp_software_train_link() follow Sean suggest
Changes in v5:
- fix some whitespcae issue
Changes in v6:
- None
drivers/gpu/drm/rockchip/Makefile | 3 +-
drivers/gpu/drm/rockchip/cdn-dp-core.c | 24 +-
drivers/gpu/drm/rockchip/cdn-dp-core.h | 2 +
drivers/gpu/drm/rockchip/cdn-dp-link-training.c | 420 ++++++++++++++++++++++++
drivers/gpu/drm/rockchip/cdn-dp-reg.c | 31 +-
drivers/gpu/drm/rockchip/cdn-dp-reg.h | 38 ++-
6 files changed, 505 insertions(+), 13 deletions(-)
create mode 100644 drivers/gpu/drm/rockchip/cdn-dp-link-training.c
diff --git a/drivers/gpu/drm/rockchip/Makefile b/drivers/gpu/drm/rockchip/Makefile
index a314e21..b932f62 100644
--- a/drivers/gpu/drm/rockchip/Makefile
+++ b/drivers/gpu/drm/rockchip/Makefile
@@ -9,7 +9,8 @@ rockchipdrm-y := rockchip_drm_drv.o rockchip_drm_fb.o \
rockchipdrm-$(CONFIG_DRM_FBDEV_EMULATION) += rockchip_drm_fbdev.o
rockchipdrm-$(CONFIG_ROCKCHIP_ANALOGIX_DP) += analogix_dp-rockchip.o
-rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o
+rockchipdrm-$(CONFIG_ROCKCHIP_CDN_DP) += cdn-dp-core.o cdn-dp-reg.o \
+ cdn-dp-link-training.o
rockchipdrm-$(CONFIG_ROCKCHIP_DW_HDMI) += dw_hdmi-rockchip.o
rockchipdrm-$(CONFIG_ROCKCHIP_DW_MIPI_DSI) += dw-mipi-dsi.o
rockchipdrm-$(CONFIG_ROCKCHIP_INNO_HDMI) += inno_hdmi.o
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
index cce64c1..d9d0d4d 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -629,11 +629,13 @@ static void cdn_dp_encoder_enable(struct drm_encoder *encoder)
goto out;
}
}
-
- ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_IDLE);
- if (ret) {
- DRM_DEV_ERROR(dp->dev, "Failed to idle video %d\n", ret);
- goto out;
+ if (dp->use_fw_training == true) {
+ ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_IDLE);
+ if (ret) {
+ DRM_DEV_ERROR(dp->dev,
+ "Failed to idle video %d\n", ret);
+ goto out;
+ }
}
ret = cdn_dp_config_video(dp);
@@ -642,11 +644,15 @@ static void cdn_dp_encoder_enable(struct drm_encoder *encoder)
goto out;
}
- ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_VALID);
- if (ret) {
- DRM_DEV_ERROR(dp->dev, "Failed to valid video %d\n", ret);
- goto out;
+ if (dp->use_fw_training == true) {
+ ret = cdn_dp_set_video_status(dp, CONTROL_VIDEO_VALID);
+ if (ret) {
+ DRM_DEV_ERROR(dp->dev,
+ "Failed to valid video %d\n", ret);
+ goto out;
+ }
}
+
out:
mutex_unlock(&dp->lock);
}
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.h b/drivers/gpu/drm/rockchip/cdn-dp-core.h
index 46159b2..77a9793 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.h
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.h
@@ -84,6 +84,7 @@ struct cdn_dp_device {
bool connected;
bool active;
bool suspended;
+ bool use_fw_training;
const struct firmware *fw; /* cdn dp firmware */
unsigned int fw_version; /* cdn fw version */
@@ -106,6 +107,7 @@ struct cdn_dp_device {
u8 ports;
u8 lanes;
int active_port;
+ u8 train_set[4];
u8 dpcd[DP_RECEIVER_CAP_SIZE];
bool sink_has_audio;
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-link-training.c b/drivers/gpu/drm/rockchip/cdn-dp-link-training.c
new file mode 100644
index 0000000..73c3290
--- /dev/null
+++ b/drivers/gpu/drm/rockchip/cdn-dp-link-training.c
@@ -0,0 +1,420 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
+ * Author: Chris Zhong <zyw@rock-chips.com>
+ */
+
+#include <linux/device.h>
+#include <linux/delay.h>
+#include <linux/phy/phy.h>
+#include <soc/rockchip/rockchip_phy_typec.h>
+
+#include "cdn-dp-core.h"
+#include "cdn-dp-reg.h"
+
+static void cdn_dp_set_signal_levels(struct cdn_dp_device *dp)
+{
+ struct cdn_dp_port *port = dp->port[dp->active_port];
+ struct rockchip_typec_phy *tcphy = phy_get_drvdata(port->phy);
+
+ int rate = drm_dp_bw_code_to_link_rate(dp->link.rate);
+ u8 swing = (dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) >>
+ DP_TRAIN_VOLTAGE_SWING_SHIFT;
+ u8 pre_emphasis = (dp->train_set[0] & DP_TRAIN_PRE_EMPHASIS_MASK)
+ >> DP_TRAIN_PRE_EMPHASIS_SHIFT;
+
+ tcphy->typec_phy_config(port->phy, rate, dp->link.num_lanes,
+ swing, pre_emphasis);
+}
+
+static int cdn_dp_set_pattern(struct cdn_dp_device *dp, uint8_t dp_train_pat)
+{
+ u32 phy_config, global_config;
+ int ret;
+ uint8_t pattern = dp_train_pat & DP_TRAINING_PATTERN_MASK;
+
+ global_config = NUM_LANES(dp->link.num_lanes - 1) | SST_MODE |
+ GLOBAL_EN | RG_EN | ENC_RST_DIS | WR_VHSYNC_FALL;
+
+ phy_config = DP_TX_PHY_ENCODER_BYPASS(0) |
+ DP_TX_PHY_SKEW_BYPASS(0) |
+ DP_TX_PHY_DISPARITY_RST(0) |
+ DP_TX_PHY_LANE0_SKEW(0) |
+ DP_TX_PHY_LANE1_SKEW(1) |
+ DP_TX_PHY_LANE2_SKEW(2) |
+ DP_TX_PHY_LANE3_SKEW(3) |
+ DP_TX_PHY_10BIT_ENABLE(0);
+
+ if (pattern != DP_TRAINING_PATTERN_DISABLE) {
+ global_config |= NO_VIDEO;
+ phy_config |= DP_TX_PHY_TRAINING_ENABLE(1) |
+ DP_TX_PHY_SCRAMBLER_BYPASS(1) |
+ DP_TX_PHY_TRAINING_PATTERN(pattern);
+ }
+
+ ret = cdn_dp_reg_write(dp, DP_FRAMER_GLOBAL_CONFIG, global_config);
+ if (ret) {
+ DRM_ERROR("fail to set DP_FRAMER_GLOBAL_CONFIG, error: %d\n",
+ ret);
+ return ret;
+ }
+
+ ret = cdn_dp_reg_write(dp, DP_TX_PHY_CONFIG_REG, phy_config);
+ if (ret) {
+ DRM_ERROR("fail to set DP_TX_PHY_CONFIG_REG, error: %d\n",
+ ret);
+ return ret;
+ }
+
+ ret = cdn_dp_reg_write(dp, DPTX_LANE_EN, BIT(dp->link.num_lanes) - 1);
+ if (ret) {
+ DRM_ERROR("fail to set DPTX_LANE_EN, error: %d\n", ret);
+ return ret;
+ }
+
+ if (drm_dp_enhanced_frame_cap(dp->dpcd))
+ ret = cdn_dp_reg_write(dp, DPTX_ENHNCD, 1);
+ else
+ ret = cdn_dp_reg_write(dp, DPTX_ENHNCD, 0);
+ if (ret)
+ DRM_ERROR("failed to set DPTX_ENHNCD, error: %x\n", ret);
+
+ return ret;
+}
+
+static u8 cdn_dp_pre_emphasis_max(u8 voltage_swing)
+{
+ switch (voltage_swing & DP_TRAIN_VOLTAGE_SWING_MASK) {
+ case DP_TRAIN_VOLTAGE_SWING_LEVEL_0:
+ return DP_TRAIN_PRE_EMPH_LEVEL_3;
+ case DP_TRAIN_VOLTAGE_SWING_LEVEL_1:
+ return DP_TRAIN_PRE_EMPH_LEVEL_2;
+ case DP_TRAIN_VOLTAGE_SWING_LEVEL_2:
+ return DP_TRAIN_PRE_EMPH_LEVEL_1;
+ default:
+ return DP_TRAIN_PRE_EMPH_LEVEL_0;
+ }
+}
+
+static void cdn_dp_get_adjust_train(struct cdn_dp_device *dp,
+ uint8_t link_status[DP_LINK_STATUS_SIZE])
+{
+ int i;
+ uint8_t v = 0, p = 0;
+ uint8_t preemph_max;
+
+ for (i = 0; i < dp->link.num_lanes; i++) {
+ v = max(v, drm_dp_get_adjust_request_voltage(link_status, i));
+ p = max(p, drm_dp_get_adjust_request_pre_emphasis(link_status,
+ i));
+ }
+
+ if (v >= VOLTAGE_LEVEL_2)
+ v = VOLTAGE_LEVEL_2 | DP_TRAIN_MAX_SWING_REACHED;
+
+ preemph_max = cdn_dp_pre_emphasis_max(v);
+ if (p >= preemph_max)
+ p = preemph_max | DP_TRAIN_MAX_PRE_EMPHASIS_REACHED;
+
+ for (i = 0; i < dp->link.num_lanes; i++)
+ dp->train_set[i] = v | p;
+}
+
+/*
+ * Pick training pattern for channel equalization. Training Pattern 3 for HBR2
+ * or 1.2 devices that support it, Training Pattern 2 otherwise.
+ */
+static u32 cdn_dp_select_chaneq_pattern(struct cdn_dp_device *dp)
+{
+ u32 training_pattern = DP_TRAINING_PATTERN_2;
+
+ /*
+ * cdn dp support HBR2 also support TPS3. TPS3 support is also mandatory
+ * for downstream devices that support HBR2. However, not all sinks
+ * follow the spec.
+ */
+ if (drm_dp_tps3_supported(dp->dpcd))
+ training_pattern = DP_TRAINING_PATTERN_3;
+ else
+ DRM_DEBUG_KMS("5.4 Gbps link rate without sink TPS3 support\n");
+
+ return training_pattern;
+}
+
+
+static bool cdn_dp_link_max_vswing_reached(struct cdn_dp_device *dp)
+{
+ int lane;
+
+ for (lane = 0; lane < dp->link.num_lanes; lane++)
+ if ((dp->train_set[lane] & DP_TRAIN_MAX_SWING_REACHED) == 0)
+ return false;
+
+ return true;
+}
+
+static int cdn_dp_update_link_train(struct cdn_dp_device *dp)
+{
+ int ret;
+
+ cdn_dp_set_signal_levels(dp);
+
+ ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_LANE0_SET,
+ dp->train_set, dp->link.num_lanes);
+ if (ret != dp->link.num_lanes)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int cdn_dp_set_link_train(struct cdn_dp_device *dp,
+ uint8_t dp_train_pat)
+{
+ uint8_t buf[sizeof(dp->train_set) + 1];
+ int ret, len;
+
+ buf[0] = dp_train_pat;
+ if ((dp_train_pat & DP_TRAINING_PATTERN_MASK) ==
+ DP_TRAINING_PATTERN_DISABLE) {
+ /* don't write DP_TRAINING_LANEx_SET on disable */
+ len = 1;
+ } else {
+ /* DP_TRAINING_LANEx_SET follow DP_TRAINING_PATTERN_SET */
+ memcpy(buf + 1, dp->train_set, dp->link.num_lanes);
+ len = dp->link.num_lanes + 1;
+ }
+
+ ret = drm_dp_dpcd_write(&dp->aux, DP_TRAINING_PATTERN_SET,
+ buf, len);
+ if (ret != len)
+ return -EINVAL;
+
+ return 0;
+}
+
+static int cdn_dp_reset_link_train(struct cdn_dp_device *dp,
+ uint8_t dp_train_pat)
+{
+ int ret;
+
+ memset(dp->train_set, 0, sizeof(dp->train_set));
+
+ cdn_dp_set_signal_levels(dp);
+
+ ret = cdn_dp_set_pattern(dp, dp_train_pat);
+ if (ret)
+ return ret;
+
+ return cdn_dp_set_link_train(dp, dp_train_pat);
+}
+
+/* Enable corresponding port and start training pattern 1 */
+static int cdn_dp_link_training_clock_recovery(struct cdn_dp_device *dp)
+{
+ u8 voltage;
+ u8 link_status[DP_LINK_STATUS_SIZE];
+ u32 voltage_tries, max_vswing_tries;
+ int ret;
+
+ /* clock recovery */
+ ret = cdn_dp_reset_link_train(dp, DP_TRAINING_PATTERN_1 |
+ DP_LINK_SCRAMBLING_DISABLE);
+ if (ret) {
+ DRM_ERROR("failed to start link train\n");
+ return ret;
+ }
+
+ voltage_tries = 1;
+ max_vswing_tries = 0;
+ for (;;) {
+ drm_dp_link_train_clock_recovery_delay(dp->dpcd);
+ if (drm_dp_dpcd_read_link_status(&dp->aux, link_status) !=
+ DP_LINK_STATUS_SIZE) {
+ DRM_ERROR("failed to get link status\n");
+ return -EINVAL;
+ }
+
+ if (drm_dp_clock_recovery_ok(link_status, dp->link.num_lanes)) {
+ DRM_DEBUG_KMS("clock recovery OK\n");
+ return 0;
+ }
+
+ if (voltage_tries >= 5) {
+ DRM_DEBUG_KMS("Same voltage tried 5 times\n");
+ return -EINVAL;
+ }
+
+ if (max_vswing_tries >= 1) {
+ DRM_DEBUG_KMS("Max Voltage Swing reached\n");
+ return -EINVAL;
+ }
+
+ voltage = dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK;
+
+ /* Update training set as requested by target */
+ cdn_dp_get_adjust_train(dp, link_status);
+ if (cdn_dp_update_link_train(dp)) {
+ DRM_ERROR("failed to update link training\n");
+ return -EINVAL;
+ }
+
+ if ((dp->train_set[0] & DP_TRAIN_VOLTAGE_SWING_MASK) ==
+ voltage)
+ ++voltage_tries;
+ else
+ voltage_tries = 1;
+
+ if (cdn_dp_link_max_vswing_reached(dp))
+ ++max_vswing_tries;
+ }
+}
+
+static int cdn_dp_link_training_channel_equalization(struct cdn_dp_device *dp)
+{
+ int tries, ret;
+ u32 training_pattern;
+ uint8_t link_status[DP_LINK_STATUS_SIZE];
+
+ training_pattern = cdn_dp_select_chaneq_pattern(dp);
+ training_pattern |= DP_LINK_SCRAMBLING_DISABLE;
+
+ ret = cdn_dp_set_pattern(dp, training_pattern);
+ if (ret)
+ return ret;
+
+ ret = cdn_dp_set_link_train(dp, training_pattern);
+ if (ret) {
+ DRM_ERROR("failed to start channel equalization\n");
+ return ret;
+ }
+
+ for (tries = 0; tries < 5; tries++) {
+ drm_dp_link_train_channel_eq_delay(dp->dpcd);
+ if (drm_dp_dpcd_read_link_status(&dp->aux, link_status) !=
+ DP_LINK_STATUS_SIZE) {
+ DRM_ERROR("failed to get link status\n");
+ break;
+ }
+
+ /* Make sure clock is still ok */
+ if (!drm_dp_clock_recovery_ok(link_status,
+ dp->link.num_lanes)) {
+ DRM_DEBUG_KMS("Clock recovery check failed\n");
+ break;
+ }
+
+ if (drm_dp_channel_eq_ok(link_status, dp->link.num_lanes)) {
+ DRM_DEBUG_KMS("Channel EQ done\n");
+ return 0;
+ }
+
+ /* Update training set as requested by target */
+ cdn_dp_get_adjust_train(dp, link_status);
+ if (cdn_dp_update_link_train(dp)) {
+ DRM_ERROR("failed to update link training\n");
+ break;
+ }
+ }
+
+ /* Try 5 times, else fail and try at lower BW */
+ if (tries == 5)
+ DRM_DEBUG_KMS("Channel equalization failed 5 times\n");
+
+ return -EINVAL;
+}
+
+static int cdn_dp_stop_link_train(struct cdn_dp_device *dp)
+{
+ int ret = cdn_dp_set_pattern(dp, DP_TRAINING_PATTERN_DISABLE);
+
+ if (ret)
+ return ret;
+
+ return cdn_dp_set_link_train(dp, DP_TRAINING_PATTERN_DISABLE);
+}
+
+static int cdn_dp_get_lower_link_rate(struct cdn_dp_device *dp)
+{
+ switch (dp->link.rate) {
+ case DP_LINK_BW_1_62:
+ return -EINVAL;
+ case DP_LINK_BW_2_7:
+ dp->link.rate = DP_LINK_BW_1_62;
+ break;
+ case DP_LINK_BW_5_4:
+ dp->link.rate = DP_LINK_BW_2_7;
+ break;
+ default:
+ dp->link.rate = DP_LINK_BW_5_4;
+ break;
+ }
+
+ return 0;
+}
+
+int cdn_dp_software_train_link(struct cdn_dp_device *dp)
+{
+ int ret, stop_err;
+ u8 link_config[2];
+ u32 rate, sink_max, source_max;
+
+ ret = drm_dp_dpcd_read(&dp->aux, DP_DPCD_REV, dp->dpcd,
+ sizeof(dp->dpcd));
+ if (ret < 0) {
+ DRM_DEV_ERROR(dp->dev, "Failed to get caps %d\n", ret);
+ return ret;
+ }
+
+ source_max = dp->lanes;
+ sink_max = drm_dp_max_lane_count(dp->dpcd);
+ dp->link.num_lanes = min(source_max, sink_max);
+
+ source_max = drm_dp_bw_code_to_link_rate(CDN_DP_MAX_LINK_RATE);
+ sink_max = drm_dp_max_link_rate(dp->dpcd);
+ rate = min(source_max, sink_max);
+ dp->link.rate = drm_dp_link_rate_to_bw_code(rate);
+
+ link_config[0] = 0;
+ link_config[1] = 0;
+ if (dp->dpcd[DP_MAIN_LINK_CHANNEL_CODING] & 0x01)
+ link_config[1] = DP_SET_ANSI_8B10B;
+ drm_dp_dpcd_write(&dp->aux, DP_DOWNSPREAD_CTRL, link_config, 2);
+
+ while (true) {
+
+ /* Write the link configuration data */
+ link_config[0] = dp->link.rate;
+ link_config[1] = dp->link.num_lanes;
+ if (drm_dp_enhanced_frame_cap(dp->dpcd))
+ link_config[1] |= DP_LANE_COUNT_ENHANCED_FRAME_EN;
+ drm_dp_dpcd_write(&dp->aux, DP_LINK_BW_SET, link_config, 2);
+
+ ret = cdn_dp_link_training_clock_recovery(dp);
+ if (ret) {
+ if (!cdn_dp_get_lower_link_rate(dp))
+ continue;
+
+ DRM_ERROR("training clock recovery failed: %d\n", ret);
+ break;
+ }
+
+ ret = cdn_dp_link_training_channel_equalization(dp);
+ if (ret) {
+ if (!cdn_dp_get_lower_link_rate(dp))
+ continue;
+
+ DRM_ERROR("training channel eq failed: %d\n", ret);
+ break;
+ }
+
+ break;
+ }
+
+ stop_err = cdn_dp_stop_link_train(dp);
+ if (stop_err) {
+ DRM_ERROR("stop training fail, error: %d\n", stop_err);
+ return stop_err;
+ }
+
+ return ret;
+}
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-reg.c b/drivers/gpu/drm/rockchip/cdn-dp-reg.c
index 979355d..e1273e6 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-reg.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-reg.c
@@ -17,7 +17,9 @@
#include <linux/delay.h>
#include <linux/io.h>
#include <linux/iopoll.h>
+#include <linux/phy/phy.h>
#include <linux/reset.h>
+#include <soc/rockchip/rockchip_phy_typec.h>
#include "cdn-dp-core.h"
#include "cdn-dp-reg.h"
@@ -189,7 +191,7 @@ static int cdn_dp_mailbox_send(struct cdn_dp_device *dp, u8 module_id,
return 0;
}
-static int cdn_dp_reg_write(struct cdn_dp_device *dp, u16 addr, u32 val)
+int cdn_dp_reg_write(struct cdn_dp_device *dp, u16 addr, u32 val)
{
u8 msg[6];
@@ -609,6 +611,31 @@ int cdn_dp_train_link(struct cdn_dp_device *dp)
{
int ret;
+ /*
+ * DP firmware uses fixed phy config values to do training, but some
+ * boards need to adjust these values to fit for their unique hardware
+ * design. So if the phy is using custom config values, do software
+ * link training instead of relying on firmware, if software training
+ * fail, keep firmware training as a fallback if sw training fails.
+ */
+ ret = cdn_dp_software_train_link(dp);
+ if (ret) {
+ DRM_DEV_ERROR(dp->dev,
+ "Failed to do software training %d\n", ret);
+ goto do_fw_training;
+ }
+ ret = cdn_dp_reg_write(dp, SOURCE_HDTX_CAR, 0xf);
+ if (ret) {
+ DRM_DEV_ERROR(dp->dev,
+ "Failed to write SOURCE_HDTX_CAR register %d\n", ret);
+ goto do_fw_training;
+ }
+ dp->use_fw_training = false;
+ return 0;
+
+do_fw_training:
+ dp->use_fw_training = true;
+ DRM_DEV_DEBUG_KMS(dp->dev, "use fw training\n");
ret = cdn_dp_training_start(dp);
if (ret) {
DRM_DEV_ERROR(dp->dev, "Failed to start training %d\n", ret);
@@ -623,7 +650,7 @@ int cdn_dp_train_link(struct cdn_dp_device *dp)
DRM_DEV_DEBUG_KMS(dp->dev, "rate:0x%x, lanes:%d\n", dp->link.rate,
dp->link.num_lanes);
- return ret;
+ return 0;
}
int cdn_dp_set_video_status(struct cdn_dp_device *dp, int active)
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-reg.h b/drivers/gpu/drm/rockchip/cdn-dp-reg.h
index 6580b11..3420771 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-reg.h
+++ b/drivers/gpu/drm/rockchip/cdn-dp-reg.h
@@ -137,7 +137,7 @@
#define HPD_EVENT_MASK 0x211c
#define HPD_EVENT_DET 0x2120
-/* dpyx framer addr */
+/* dptx framer addr */
#define DP_FRAMER_GLOBAL_CONFIG 0x2200
#define DP_SW_RESET 0x2204
#define DP_FRAMER_TU 0x2208
@@ -431,6 +431,40 @@
/* Reference cycles when using lane clock as reference */
#define LANE_REF_CYC 0x8000
+/* register CM_VID_CTRL */
+#define LANE_VID_REF_CYC(x) (((x) & (BIT(24) - 1)) << 0)
+#define NMVID_MEAS_TOLERANCE(x) (((x) & 0xf) << 24)
+
+/* register DP_TX_PHY_CONFIG_REG */
+#define DP_TX_PHY_TRAINING_ENABLE(x) ((x) & 1)
+#define DP_TX_PHY_TRAINING_TYPE_PRBS7 (0 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_TPS1 (1 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_TPS2 (2 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_TPS3 (3 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_TPS4 (4 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_PLTPAT (5 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_D10_2 (6 << 1)
+#define DP_TX_PHY_TRAINING_TYPE_HBR2CPAT (8 << 1)
+#define DP_TX_PHY_TRAINING_PATTERN(x) ((x) << 1)
+#define DP_TX_PHY_SCRAMBLER_BYPASS(x) (((x) & 1) << 5)
+#define DP_TX_PHY_ENCODER_BYPASS(x) (((x) & 1) << 6)
+#define DP_TX_PHY_SKEW_BYPASS(x) (((x) & 1) << 7)
+#define DP_TX_PHY_DISPARITY_RST(x) (((x) & 1) << 8)
+#define DP_TX_PHY_LANE0_SKEW(x) (((x) & 7) << 9)
+#define DP_TX_PHY_LANE1_SKEW(x) (((x) & 7) << 12)
+#define DP_TX_PHY_LANE2_SKEW(x) (((x) & 7) << 15)
+#define DP_TX_PHY_LANE3_SKEW(x) (((x) & 7) << 18)
+#define DP_TX_PHY_10BIT_ENABLE(x) (((x) & 1) << 21)
+
+/* register DP_FRAMER_GLOBAL_CONFIG */
+#define NUM_LANES(x) ((x) & 3)
+#define SST_MODE (0 << 2)
+#define RG_EN (0 << 4)
+#define GLOBAL_EN BIT(3)
+#define NO_VIDEO BIT(5)
+#define ENC_RST_DIS BIT(6)
+#define WR_VHSYNC_FALL BIT(7)
+
enum voltage_swing_level {
VOLTAGE_LEVEL_0,
VOLTAGE_LEVEL_1,
@@ -476,6 +510,7 @@ int cdn_dp_set_host_cap(struct cdn_dp_device *dp, u8 lanes, bool flip);
int cdn_dp_event_config(struct cdn_dp_device *dp);
u32 cdn_dp_get_event(struct cdn_dp_device *dp);
int cdn_dp_get_hpd_status(struct cdn_dp_device *dp);
+int cdn_dp_reg_write(struct cdn_dp_device *dp, u16 addr, u32 val);
ssize_t cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr,
u8 *data, u16 len);
ssize_t cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr,
@@ -489,4 +524,5 @@ int cdn_dp_config_video(struct cdn_dp_device *dp);
int cdn_dp_audio_stop(struct cdn_dp_device *dp, struct audio_info *audio);
int cdn_dp_audio_mute(struct cdn_dp_device *dp, bool enable);
int cdn_dp_audio_config(struct cdn_dp_device *dp, struct audio_info *audio);
+int cdn_dp_software_train_link(struct cdn_dp_device *dp);
#endif /* _CDN_DP_REG_H */
--
2.7.4
^ permalink raw reply related
* [PATCH v6 4/5] phy: rockchip-typec: support variable phy config value
From: Lin Huang @ 2018-05-21 9:37 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526895424-22894-1-git-send-email-hl@rock-chips.com>
the phy config values used to fix in dp firmware, but some boards
need change these values to do training and get the better eye diagram
result. So support that in phy driver.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
---
Changes in v2:
- update patch following Enric suggest
Changes in v3:
- delete need_software_training variable
- add default phy config value, if dts do not define phy config value, use these value
Changes in v4:
- rename variable config to tcphy_default_config
Changes in v5:
- None
Changes in v6:
- split the header file to new patch
drivers/phy/rockchip/phy-rockchip-typec.c | 261 ++++++++++++++++++++++++------
1 file changed, 208 insertions(+), 53 deletions(-)
diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
index 795055f..4c4b925 100644
--- a/drivers/phy/rockchip/phy-rockchip-typec.c
+++ b/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -324,21 +324,29 @@
* clock 0: PLL 0 div 1
* clock 1: PLL 1 div 2
*/
-#define CLK_PLL_CONFIG 0X30
+#define CLK_PLL1_DIV1 0x20
+#define CLK_PLL1_DIV2 0x30
#define CLK_PLL_MASK 0x33
#define CMN_READY BIT(0)
+#define DP_PLL_CLOCK_ENABLE_ACK BIT(3)
#define DP_PLL_CLOCK_ENABLE BIT(2)
+#define DP_PLL_ENABLE_ACK BIT(1)
#define DP_PLL_ENABLE BIT(0)
#define DP_PLL_DATA_RATE_RBR ((2 << 12) | (4 << 8))
#define DP_PLL_DATA_RATE_HBR ((2 << 12) | (4 << 8))
#define DP_PLL_DATA_RATE_HBR2 ((1 << 12) | (2 << 8))
+#define DP_PLL_DATA_RATE_MASK 0xff00
-#define DP_MODE_A0 BIT(4)
-#define DP_MODE_A2 BIT(6)
-#define DP_MODE_ENTER_A0 0xc101
-#define DP_MODE_ENTER_A2 0xc104
+#define DP_MODE_MASK 0xf
+#define DP_MODE_ENTER_A0 BIT(0)
+#define DP_MODE_ENTER_A2 BIT(2)
+#define DP_MODE_ENTER_A3 BIT(3)
+#define DP_MODE_A0_ACK BIT(4)
+#define DP_MODE_A2_ACK BIT(6)
+#define DP_MODE_A3_ACK BIT(7)
+#define DP_LINK_RESET_DEASSERTED BIT(8)
#define PHY_MODE_SET_TIMEOUT 100000
@@ -350,6 +358,8 @@
#define MODE_DFP_USB BIT(1)
#define MODE_DFP_DP BIT(2)
+#define DP_DEFAULT_RATE 162000
+
struct phy_reg {
u16 value;
u32 addr;
@@ -372,15 +382,15 @@ struct phy_reg usb3_pll_cfg[] = {
{ 0x8, CMN_DIAG_PLL0_LF_PROG },
};
-struct phy_reg dp_pll_cfg[] = {
+struct phy_reg dp_pll_rbr_cfg[] = {
{ 0xf0, CMN_PLL1_VCOCAL_INIT },
{ 0x18, CMN_PLL1_VCOCAL_ITER },
{ 0x30b9, CMN_PLL1_VCOCAL_START },
- { 0x21c, CMN_PLL1_INTDIV },
+ { 0x87, CMN_PLL1_INTDIV },
{ 0, CMN_PLL1_FRACDIV },
- { 0x5, CMN_PLL1_HIGH_THR },
- { 0x35, CMN_PLL1_SS_CTRL1 },
- { 0x7f1e, CMN_PLL1_SS_CTRL2 },
+ { 0x22, CMN_PLL1_HIGH_THR },
+ { 0x8000, CMN_PLL1_SS_CTRL1 },
+ { 0, CMN_PLL1_SS_CTRL2 },
{ 0x20, CMN_PLL1_DSM_DIAG },
{ 0, CMN_PLLSM1_USER_DEF_CTRL },
{ 0, CMN_DIAG_PLL1_OVRD },
@@ -391,9 +401,52 @@ struct phy_reg dp_pll_cfg[] = {
{ 0x8, CMN_DIAG_PLL1_LF_PROG },
{ 0x100, CMN_DIAG_PLL1_PTATIS_TUNE1 },
{ 0x7, CMN_DIAG_PLL1_PTATIS_TUNE2 },
- { 0x4, CMN_DIAG_PLL1_INCLK_CTRL },
+ { 0x1, CMN_DIAG_PLL1_INCLK_CTRL },
};
+struct phy_reg dp_pll_hbr_cfg[] = {
+ { 0xf0, CMN_PLL1_VCOCAL_INIT },
+ { 0x18, CMN_PLL1_VCOCAL_ITER },
+ { 0x30b4, CMN_PLL1_VCOCAL_START },
+ { 0xe1, CMN_PLL1_INTDIV },
+ { 0, CMN_PLL1_FRACDIV },
+ { 0x5, CMN_PLL1_HIGH_THR },
+ { 0x8000, CMN_PLL1_SS_CTRL1 },
+ { 0, CMN_PLL1_SS_CTRL2 },
+ { 0x20, CMN_PLL1_DSM_DIAG },
+ { 0x1000, CMN_PLLSM1_USER_DEF_CTRL },
+ { 0, CMN_DIAG_PLL1_OVRD },
+ { 0, CMN_DIAG_PLL1_FBH_OVRD },
+ { 0, CMN_DIAG_PLL1_FBL_OVRD },
+ { 0x7, CMN_DIAG_PLL1_V2I_TUNE },
+ { 0x45, CMN_DIAG_PLL1_CP_TUNE },
+ { 0x8, CMN_DIAG_PLL1_LF_PROG },
+ { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE1 },
+ { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE2 },
+ { 0x1, CMN_DIAG_PLL1_INCLK_CTRL },
+};
+
+struct phy_reg dp_pll_hbr2_cfg[] = {
+ { 0xf0, CMN_PLL1_VCOCAL_INIT },
+ { 0x18, CMN_PLL1_VCOCAL_ITER },
+ { 0x30b4, CMN_PLL1_VCOCAL_START },
+ { 0xe1, CMN_PLL1_INTDIV },
+ { 0, CMN_PLL1_FRACDIV },
+ { 0x5, CMN_PLL1_HIGH_THR },
+ { 0x8000, CMN_PLL1_SS_CTRL1 },
+ { 0, CMN_PLL1_SS_CTRL2 },
+ { 0x20, CMN_PLL1_DSM_DIAG },
+ { 0x1000, CMN_PLLSM1_USER_DEF_CTRL },
+ { 0, CMN_DIAG_PLL1_OVRD },
+ { 0, CMN_DIAG_PLL1_FBH_OVRD },
+ { 0, CMN_DIAG_PLL1_FBL_OVRD },
+ { 0x7, CMN_DIAG_PLL1_V2I_TUNE },
+ { 0x45, CMN_DIAG_PLL1_CP_TUNE },
+ { 0x8, CMN_DIAG_PLL1_LF_PROG },
+ { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE1 },
+ { 0x1, CMN_DIAG_PLL1_PTATIS_TUNE2 },
+ { 0x1, CMN_DIAG_PLL1_INCLK_CTRL },
+};
static const struct rockchip_usb3phy_port_cfg rk3399_usb3phy_port_cfgs[] = {
{
.reg = 0xff7c0000,
@@ -418,6 +471,24 @@ static const struct rockchip_usb3phy_port_cfg rk3399_usb3phy_port_cfgs[] = {
{ /* sentinel */ }
};
+/* default phy config */
+static const struct phy_config tcphy_default_config[3][4] = {
+ {{ .swing = 0x2a, .pe = 0x00 },
+ { .swing = 0x1f, .pe = 0x15 },
+ { .swing = 0x14, .pe = 0x22 },
+ { .swing = 0x02, .pe = 0x2b } },
+
+ {{ .swing = 0x21, .pe = 0x00 },
+ { .swing = 0x12, .pe = 0x15 },
+ { .swing = 0x02, .pe = 0x22 },
+ { .swing = 0, .pe = 0 } },
+
+ {{ .swing = 0x15, .pe = 0x00 },
+ { .swing = 0x00, .pe = 0x15 },
+ { .swing = 0, .pe = 0 },
+ { .swing = 0, .pe = 0 } },
+};
+
static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
{
u32 i, rdata;
@@ -439,7 +510,7 @@ static void tcphy_cfg_24m(struct rockchip_typec_phy *tcphy)
rdata = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
rdata &= ~CLK_PLL_MASK;
- rdata |= CLK_PLL_CONFIG;
+ rdata |= CLK_PLL1_DIV2;
writel(rdata, tcphy->base + CMN_DIAG_HSCLK_SEL);
}
@@ -453,17 +524,44 @@ static void tcphy_cfg_usb3_pll(struct rockchip_typec_phy *tcphy)
tcphy->base + usb3_pll_cfg[i].addr);
}
-static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy)
+static void tcphy_cfg_dp_pll(struct rockchip_typec_phy *tcphy, int link_rate)
{
- u32 i;
+ struct phy_reg *phy_cfg;
+ u32 clk_ctrl;
+ u32 i, cfg_size, hsclk_sel;
+
+ hsclk_sel = readl(tcphy->base + CMN_DIAG_HSCLK_SEL);
+ hsclk_sel &= ~CLK_PLL_MASK;
+
+ switch (link_rate) {
+ case 162000:
+ clk_ctrl = DP_PLL_DATA_RATE_RBR;
+ hsclk_sel |= CLK_PLL1_DIV2;
+ phy_cfg = dp_pll_rbr_cfg;
+ cfg_size = ARRAY_SIZE(dp_pll_rbr_cfg);
+ break;
+ case 270000:
+ clk_ctrl = DP_PLL_DATA_RATE_HBR;
+ hsclk_sel |= CLK_PLL1_DIV2;
+ phy_cfg = dp_pll_hbr_cfg;
+ cfg_size = ARRAY_SIZE(dp_pll_hbr_cfg);
+ break;
+ case 540000:
+ clk_ctrl = DP_PLL_DATA_RATE_HBR2;
+ hsclk_sel |= CLK_PLL1_DIV1;
+ phy_cfg = dp_pll_hbr2_cfg;
+ cfg_size = ARRAY_SIZE(dp_pll_hbr2_cfg);
+ break;
+ }
- /* set the default mode to RBR */
- writel(DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE | DP_PLL_DATA_RATE_RBR,
- tcphy->base + DP_CLK_CTL);
+ clk_ctrl |= DP_PLL_CLOCK_ENABLE | DP_PLL_ENABLE;
+ writel(clk_ctrl, tcphy->base + DP_CLK_CTL);
+
+ writel(hsclk_sel, tcphy->base + CMN_DIAG_HSCLK_SEL);
/* load the configuration of PLL1 */
- for (i = 0; i < ARRAY_SIZE(dp_pll_cfg); i++)
- writel(dp_pll_cfg[i].value, tcphy->base + dp_pll_cfg[i].addr);
+ for (i = 0; i < cfg_size; i++)
+ writel(phy_cfg[i].value, tcphy->base + phy_cfg[i].addr);
}
static void tcphy_tx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
@@ -490,9 +588,10 @@ static void tcphy_rx_usb3_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
writel(0xfb, tcphy->base + XCVR_DIAG_BIDI_CTRL(lane));
}
-static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
+static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, int link_rate,
+ u8 swing, u8 pre_emp, u32 lane)
{
- u16 rdata;
+ u16 val;
writel(0xbefc, tcphy->base + XCVR_PSM_RCTRL(lane));
writel(0x6799, tcphy->base + TX_PSC_A0(lane));
@@ -500,25 +599,31 @@ static void tcphy_dp_cfg_lane(struct rockchip_typec_phy *tcphy, u32 lane)
writel(0x98, tcphy->base + TX_PSC_A2(lane));
writel(0x98, tcphy->base + TX_PSC_A3(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_001(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_010(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_011(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_100(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_101(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_110(lane));
- writel(0, tcphy->base + TX_TXCC_MGNFS_MULT_111(lane));
- writel(0, tcphy->base + TX_TXCC_CPOST_MULT_10(lane));
- writel(0, tcphy->base + TX_TXCC_CPOST_MULT_01(lane));
- writel(0, tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
- writel(0, tcphy->base + TX_TXCC_CPOST_MULT_11(lane));
-
- writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
- writel(0x400, tcphy->base + TX_DIAG_TX_DRV(lane));
-
- rdata = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
- rdata = (rdata & 0x8fff) | 0x6000;
- writel(rdata, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
+ writel(tcphy->config[swing][pre_emp].swing,
+ tcphy->base + TX_TXCC_MGNFS_MULT_000(lane));
+ writel(tcphy->config[swing][pre_emp].pe,
+ tcphy->base + TX_TXCC_CPOST_MULT_00(lane));
+
+ if (swing == 2 && pre_emp == 0 && link_rate != 540000) {
+ writel(0x700, tcphy->base + TX_DIAG_TX_DRV(lane));
+ writel(0x13c, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
+ } else {
+ writel(0x128, tcphy->base + TX_TXCC_CAL_SCLR_MULT(lane));
+ writel(0x0400, tcphy->base + TX_DIAG_TX_DRV(lane));
+ }
+
+ val = readl(tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
+ val = val & 0x8fff;
+ switch (link_rate) {
+ case 162000:
+ case 270000:
+ val |= (6 << 12);
+ break;
+ case 540000:
+ val |= (4 << 12);
+ break;
+ }
+ writel(val, tcphy->base + XCVR_DIAG_PLLDRC_CTRL(lane));
}
static inline int property_enable(struct rockchip_typec_phy *tcphy,
@@ -709,30 +814,33 @@ static int tcphy_phy_init(struct rockchip_typec_phy *tcphy, u8 mode)
tcphy_cfg_24m(tcphy);
if (mode == MODE_DFP_DP) {
- tcphy_cfg_dp_pll(tcphy);
+ tcphy_cfg_dp_pll(tcphy, DP_DEFAULT_RATE);
for (i = 0; i < 4; i++)
- tcphy_dp_cfg_lane(tcphy, i);
+ tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, i);
writel(PIN_ASSIGN_C_E, tcphy->base + PMA_LANE_CFG);
} else {
tcphy_cfg_usb3_pll(tcphy);
- tcphy_cfg_dp_pll(tcphy);
+ tcphy_cfg_dp_pll(tcphy, DP_DEFAULT_RATE);
if (tcphy->flip) {
tcphy_tx_usb3_cfg_lane(tcphy, 3);
tcphy_rx_usb3_cfg_lane(tcphy, 2);
- tcphy_dp_cfg_lane(tcphy, 0);
- tcphy_dp_cfg_lane(tcphy, 1);
+ tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 0);
+ tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 1);
} else {
tcphy_tx_usb3_cfg_lane(tcphy, 0);
tcphy_rx_usb3_cfg_lane(tcphy, 1);
- tcphy_dp_cfg_lane(tcphy, 2);
- tcphy_dp_cfg_lane(tcphy, 3);
+ tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 2);
+ tcphy_dp_cfg_lane(tcphy, DP_DEFAULT_RATE, 0, 0, 3);
}
writel(PIN_ASSIGN_D_F, tcphy->base + PMA_LANE_CFG);
}
- writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+ val = readl(tcphy->base + DP_MODE_CTL);
+ val &= ~DP_MODE_MASK;
+ val |= DP_MODE_ENTER_A2 | DP_LINK_RESET_DEASSERTED;
+ writel(val, tcphy->base + DP_MODE_CTL);
reset_control_deassert(tcphy->uphy_rst);
@@ -945,7 +1053,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
property_enable(tcphy, &cfg->uphy_dp_sel, 1);
ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
- val, val & DP_MODE_A2, 1000,
+ val, val & DP_MODE_A2_ACK, 1000,
PHY_MODE_SET_TIMEOUT);
if (ret < 0) {
dev_err(tcphy->dev, "failed to wait TCPHY enter A2\n");
@@ -954,13 +1062,19 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
tcphy_dp_aux_calibration(tcphy);
- writel(DP_MODE_ENTER_A0, tcphy->base + DP_MODE_CTL);
+ /* enter A0 mode */
+ val = readl(tcphy->base + DP_MODE_CTL);
+ val &= ~DP_MODE_MASK;
+ val |= DP_MODE_ENTER_A0;
+ writel(val, tcphy->base + DP_MODE_CTL);
ret = readx_poll_timeout(readl, tcphy->base + DP_MODE_CTL,
- val, val & DP_MODE_A0, 1000,
+ val, val & DP_MODE_A0_ACK, 1000,
PHY_MODE_SET_TIMEOUT);
if (ret < 0) {
- writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+ val &= ~DP_MODE_MASK;
+ val |= DP_MODE_ENTER_A2;
+ writel(val, tcphy->base + DP_MODE_CTL);
dev_err(tcphy->dev, "failed to wait TCPHY enter A0\n");
goto power_on_finish;
}
@@ -978,6 +1092,7 @@ static int rockchip_dp_phy_power_on(struct phy *phy)
static int rockchip_dp_phy_power_off(struct phy *phy)
{
struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+ u32 val;
mutex_lock(&tcphy->lock);
@@ -986,7 +1101,10 @@ static int rockchip_dp_phy_power_off(struct phy *phy)
tcphy->mode &= ~MODE_DFP_DP;
- writel(DP_MODE_ENTER_A2, tcphy->base + DP_MODE_CTL);
+ val = readl(tcphy->base + DP_MODE_CTL);
+ val &= ~DP_MODE_MASK;
+ val |= DP_MODE_ENTER_A2;
+ writel(val, tcphy->base + DP_MODE_CTL);
if (tcphy->mode == MODE_DISCONNECT)
tcphy_phy_deinit(tcphy);
@@ -1002,9 +1120,35 @@ static const struct phy_ops rockchip_dp_phy_ops = {
.owner = THIS_MODULE,
};
+static int typec_dp_phy_config(struct phy *phy, int link_rate,
+ int lanes, u8 swing, u8 pre_emp)
+{
+ struct rockchip_typec_phy *tcphy = phy_get_drvdata(phy);
+ u8 i;
+
+ tcphy_cfg_dp_pll(tcphy, link_rate);
+
+ if (tcphy->mode == MODE_DFP_DP) {
+ for (i = 0; i < 4; i++)
+ tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, i);
+ } else {
+ if (tcphy->flip) {
+ tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 0);
+ tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 1);
+ } else {
+ tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 2);
+ tcphy_dp_cfg_lane(tcphy, link_rate, swing, pre_emp, 3);
+ }
+ }
+
+ return 0;
+}
+
static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
struct device *dev)
{
+ int ret;
+
tcphy->grf_regs = syscon_regmap_lookup_by_phandle(dev->of_node,
"rockchip,grf");
if (IS_ERR(tcphy->grf_regs)) {
@@ -1042,6 +1186,16 @@ static int tcphy_parse_dt(struct rockchip_typec_phy *tcphy,
return PTR_ERR(tcphy->tcphy_rst);
}
+ /*
+ * check if phy_config pass from dts, if no,
+ * use default phy config value.
+ */
+ ret = of_property_read_u32_array(dev->of_node, "rockchip,phy-config",
+ (u32 *)tcphy->config, sizeof(tcphy->config) / sizeof(u32));
+ if (ret)
+ memcpy(tcphy->config, tcphy_default_config,
+ sizeof(tcphy->config));
+
return 0;
}
@@ -1126,6 +1280,7 @@ static int rockchip_typec_phy_probe(struct platform_device *pdev)
}
}
+ tcphy->typec_phy_config = typec_dp_phy_config;
pm_runtime_enable(dev);
for_each_available_child_of_node(np, child_np) {
--
2.7.4
^ permalink raw reply related
* [PATCH v6 3/5] soc: rockchip: split rockchip_typec_phy struct to separate header
From: Lin Huang @ 2018-05-21 9:37 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526895424-22894-1-git-send-email-hl@rock-chips.com>
we may use rockchip_phy_typec struct in other driver, so split
it to separate header.
Signed-off-by: Lin Huang <hl@rock-chips.com>
---
Changes in v2:
- None
Changes in v3:
- None
Changes in v4:
- None
Changes in v5:
- None
Changes in v6:
- new patch here
drivers/phy/rockchip/phy-rockchip-typec.c | 47 +----------------------
include/soc/rockchip/rockchip_phy_typec.h | 63 +++++++++++++++++++++++++++++++
2 files changed, 64 insertions(+), 46 deletions(-)
create mode 100644 include/soc/rockchip/rockchip_phy_typec.h
diff --git a/drivers/phy/rockchip/phy-rockchip-typec.c b/drivers/phy/rockchip/phy-rockchip-typec.c
index 76a4b58..795055f 100644
--- a/drivers/phy/rockchip/phy-rockchip-typec.c
+++ b/drivers/phy/rockchip/phy-rockchip-typec.c
@@ -63,6 +63,7 @@
#include <linux/mfd/syscon.h>
#include <linux/phy/phy.h>
+#include <soc/rockchip/rockchip_phy_typec.h>
#define CMN_SSM_BANDGAP (0x21 << 2)
#define CMN_SSM_BIAS (0x22 << 2)
@@ -349,52 +350,6 @@
#define MODE_DFP_USB BIT(1)
#define MODE_DFP_DP BIT(2)
-struct usb3phy_reg {
- u32 offset;
- u32 enable_bit;
- u32 write_enable;
-};
-
-/**
- * struct rockchip_usb3phy_port_cfg: usb3-phy port configuration.
- * @reg: the base address for usb3-phy config.
- * @typec_conn_dir: the register of type-c connector direction.
- * @usb3tousb2_en: the register of type-c force usb2 to usb2 enable.
- * @external_psm: the register of type-c phy external psm clock.
- * @pipe_status: the register of type-c phy pipe status.
- * @usb3_host_disable: the register of type-c usb3 host disable.
- * @usb3_host_port: the register of type-c usb3 host port.
- * @uphy_dp_sel: the register of type-c phy DP select control.
- */
-struct rockchip_usb3phy_port_cfg {
- unsigned int reg;
- struct usb3phy_reg typec_conn_dir;
- struct usb3phy_reg usb3tousb2_en;
- struct usb3phy_reg external_psm;
- struct usb3phy_reg pipe_status;
- struct usb3phy_reg usb3_host_disable;
- struct usb3phy_reg usb3_host_port;
- struct usb3phy_reg uphy_dp_sel;
-};
-
-struct rockchip_typec_phy {
- struct device *dev;
- void __iomem *base;
- struct extcon_dev *extcon;
- struct regmap *grf_regs;
- struct clk *clk_core;
- struct clk *clk_ref;
- struct reset_control *uphy_rst;
- struct reset_control *pipe_rst;
- struct reset_control *tcphy_rst;
- const struct rockchip_usb3phy_port_cfg *port_cfgs;
- /* mutex to protect access to individual PHYs */
- struct mutex lock;
-
- bool flip;
- u8 mode;
-};
-
struct phy_reg {
u16 value;
u32 addr;
diff --git a/include/soc/rockchip/rockchip_phy_typec.h b/include/soc/rockchip/rockchip_phy_typec.h
new file mode 100644
index 0000000..be6af0e
--- /dev/null
+++ b/include/soc/rockchip/rockchip_phy_typec.h
@@ -0,0 +1,63 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (C) Fuzhou Rockchip Electronics Co.Ltd
+ * Author: Lin Huang <hl@rock-chips.com>
+ */
+
+#ifndef __SOC_ROCKCHIP_PHY_TYPEC_H
+#define __SOC_ROCKCHIP_PHY_TYPEC_H
+
+struct usb3phy_reg {
+ u32 offset;
+ u32 enable_bit;
+ u32 write_enable;
+};
+
+/**
+ * struct rockchip_usb3phy_port_cfg: usb3-phy port configuration.
+ * @reg: the base address for usb3-phy config.
+ * @typec_conn_dir: the register of type-c connector direction.
+ * @usb3tousb2_en: the register of type-c force usb2 to usb2 enable.
+ * @external_psm: the register of type-c phy external psm clock.
+ * @pipe_status: the register of type-c phy pipe status.
+ * @usb3_host_disable: the register of type-c usb3 host disable.
+ * @usb3_host_port: the register of type-c usb3 host port.
+ * @uphy_dp_sel: the register of type-c phy DP select control.
+ */
+struct rockchip_usb3phy_port_cfg {
+ unsigned int reg;
+ struct usb3phy_reg typec_conn_dir;
+ struct usb3phy_reg usb3tousb2_en;
+ struct usb3phy_reg external_psm;
+ struct usb3phy_reg pipe_status;
+ struct usb3phy_reg usb3_host_disable;
+ struct usb3phy_reg usb3_host_port;
+ struct usb3phy_reg uphy_dp_sel;
+};
+
+struct phy_config {
+ int swing;
+ int pe;
+};
+
+struct rockchip_typec_phy {
+ struct device *dev;
+ void __iomem *base;
+ struct extcon_dev *extcon;
+ struct regmap *grf_regs;
+ struct clk *clk_core;
+ struct clk *clk_ref;
+ struct reset_control *uphy_rst;
+ struct reset_control *pipe_rst;
+ struct reset_control *tcphy_rst;
+ const struct rockchip_usb3phy_port_cfg *port_cfgs;
+ /* mutex to protect access to individual PHYs */
+ struct mutex lock;
+ struct phy_config config[3][4];
+ bool flip;
+ u8 mode;
+ int (*typec_phy_config)(struct phy *phy, int link_rate,
+ int lanes, u8 swing, u8 pre_emp);
+};
+
+#endif
--
2.7.4
^ permalink raw reply related
* [PATCH v6 2/5] Documentation: dt-bindings: phy: add phy_config for Rockchip USB Type-C PHY
From: Lin Huang @ 2018-05-21 9:37 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526895424-22894-1-git-send-email-hl@rock-chips.com>
If want to do training outside DP Firmware, need phy voltage swing
and pre_emphasis value.
Signed-off-by: Lin Huang <hl@rock-chips.com>
---
Changes in v2:
- None
Changes in v3:
- modify property description and add this property to Example
Changes in v4:
- None
Changes in v5:
- None
Changes in v6:
- change rockchip,phy_config to rockchip,phy-config and descript it in detail.
.../devicetree/bindings/phy/phy-rockchip-typec.txt | 36 +++++++++++++++++++++-
1 file changed, 35 insertions(+), 1 deletion(-)
diff --git a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
index 960da7f..40d5e7a 100644
--- a/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
+++ b/Documentation/devicetree/bindings/phy/phy-rockchip-typec.txt
@@ -17,7 +17,11 @@ Required properties:
Optional properties:
- extcon : extcon specifier for the Power Delivery
-
+ - rockchip,phy-config : A list of voltage swing(mV) and pre-emphasis
+ (dB) pairs. They are 3 blocks of 4 entries and
+ correspond to s0p0 ~ s0p3, s1p0 ~ s1p3,
+ s2p0 ~ s2p3, s3p0 ~ s2p3 swing and pre-emphasis
+ values.
Required nodes : a sub-node is required for each port the phy provides.
The sub-node name is used to identify dp or usb3 port,
and shall be the following entries:
@@ -50,6 +54,21 @@ Example:
<&cru SRST_P_UPHY0_TCPHY>;
reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+ rockchip,phy-config = <0x2a 0x00>,
+ <0x1f 0x15>,
+ <0x14 0x22>,
+ <0x02 0x2b>,
+
+ <0x21 0x00>,
+ <0x12 0x15>,
+ <0x02 0x22>,
+ <0 0>,
+
+ <0x15 0x00>,
+ <0x00 0x15>,
+ <0 0>,
+ <0 0>;
+
tcphy0_dp: dp-port {
#phy-cells = <0>;
};
@@ -74,6 +93,21 @@ Example:
<&cru SRST_P_UPHY1_TCPHY>;
reset-names = "uphy", "uphy-pipe", "uphy-tcphy";
+ rockchip,phy-config = <0x2a 0x00>,
+ <0x1f 0x15>,
+ <0x14 0x22>,
+ <0x02 0x2b>,
+
+ <0x21 0x00>,
+ <0x12 0x15>,
+ <0x02 0x22>,
+ <0 0>,
+
+ <0x15 0x00>,
+ <0x00 0x15>,
+ <0 0>,
+ <0 0>;
+
tcphy1_dp: dp-port {
#phy-cells = <0>;
};
--
2.7.4
^ permalink raw reply related
* [PATCH v6 1/5] drm/rockchip: add transfer function for cdn-dp
From: Lin Huang @ 2018-05-21 9:37 UTC (permalink / raw)
To: linux-arm-kernel
From: Chris Zhong <zyw@rock-chips.com>
We may support training outside firmware, so we need support
dpcd read/write to get the message or do some setting with
display.
Signed-off-by: Chris Zhong <zyw@rock-chips.com>
Signed-off-by: Lin Huang <hl@rock-chips.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Reviewed-by: Enric Balletbo <enric.balletbo@collabora.com>
---
Changes in v2:
- update patch following Enric suggest
Changes in v3:
- None
Changes in v4:
- None
Changes in v5:
- None
Changes in v6:
- None
drivers/gpu/drm/rockchip/cdn-dp-core.c | 55 +++++++++++++++++++++++----
drivers/gpu/drm/rockchip/cdn-dp-core.h | 1 +
drivers/gpu/drm/rockchip/cdn-dp-reg.c | 69 ++++++++++++++++++++++++++++++----
drivers/gpu/drm/rockchip/cdn-dp-reg.h | 14 ++++++-
4 files changed, 122 insertions(+), 17 deletions(-)
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.c b/drivers/gpu/drm/rockchip/cdn-dp-core.c
index c6fbdcd..cce64c1 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.c
@@ -176,8 +176,8 @@ static int cdn_dp_get_sink_count(struct cdn_dp_device *dp, u8 *sink_count)
u8 value;
*sink_count = 0;
- ret = cdn_dp_dpcd_read(dp, DP_SINK_COUNT, &value, 1);
- if (ret)
+ ret = drm_dp_dpcd_read(&dp->aux, DP_SINK_COUNT, &value, 1);
+ if (ret < 0)
return ret;
*sink_count = DP_GET_SINK_COUNT(value);
@@ -374,9 +374,9 @@ static int cdn_dp_get_sink_capability(struct cdn_dp_device *dp)
if (!cdn_dp_check_sink_connection(dp))
return -ENODEV;
- ret = cdn_dp_dpcd_read(dp, DP_DPCD_REV, dp->dpcd,
- DP_RECEIVER_CAP_SIZE);
- if (ret) {
+ ret = drm_dp_dpcd_read(&dp->aux, DP_DPCD_REV, dp->dpcd,
+ sizeof(dp->dpcd));
+ if (ret < 0) {
DRM_DEV_ERROR(dp->dev, "Failed to get caps %d\n", ret);
return ret;
}
@@ -582,8 +582,8 @@ static bool cdn_dp_check_link_status(struct cdn_dp_device *dp)
if (!port || !dp->link.rate || !dp->link.num_lanes)
return false;
- if (cdn_dp_dpcd_read(dp, DP_LANE0_1_STATUS, link_status,
- DP_LINK_STATUS_SIZE)) {
+ if (drm_dp_dpcd_read_link_status(&dp->aux, link_status) !=
+ DP_LINK_STATUS_SIZE) {
DRM_ERROR("Failed to get link status\n");
return false;
}
@@ -1012,6 +1012,40 @@ static int cdn_dp_pd_event(struct notifier_block *nb,
return NOTIFY_DONE;
}
+static ssize_t cdn_dp_aux_transfer(struct drm_dp_aux *aux,
+ struct drm_dp_aux_msg *msg)
+{
+ struct cdn_dp_device *dp = container_of(aux, struct cdn_dp_device, aux);
+ int ret;
+ u8 status;
+
+ switch (msg->request & ~DP_AUX_I2C_MOT) {
+ case DP_AUX_NATIVE_WRITE:
+ case DP_AUX_I2C_WRITE:
+ case DP_AUX_I2C_WRITE_STATUS_UPDATE:
+ ret = cdn_dp_dpcd_write(dp, msg->address, msg->buffer,
+ msg->size);
+ break;
+ case DP_AUX_NATIVE_READ:
+ case DP_AUX_I2C_READ:
+ ret = cdn_dp_dpcd_read(dp, msg->address, msg->buffer,
+ msg->size);
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ status = cdn_dp_get_aux_status(dp);
+ if (status == AUX_STATUS_ACK)
+ msg->reply = DP_AUX_NATIVE_REPLY_ACK;
+ else if (status == AUX_STATUS_NACK)
+ msg->reply = DP_AUX_NATIVE_REPLY_NACK;
+ else if (status == AUX_STATUS_DEFER)
+ msg->reply = DP_AUX_NATIVE_REPLY_DEFER;
+
+ return ret;
+}
+
static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
{
struct cdn_dp_device *dp = dev_get_drvdata(dev);
@@ -1030,6 +1064,13 @@ static int cdn_dp_bind(struct device *dev, struct device *master, void *data)
dp->active = false;
dp->active_port = -1;
dp->fw_loaded = false;
+ dp->aux.name = "DP-AUX";
+ dp->aux.transfer = cdn_dp_aux_transfer;
+ dp->aux.dev = dev;
+
+ ret = drm_dp_aux_register(&dp->aux);
+ if (ret)
+ return ret;
INIT_WORK(&dp->event_work, cdn_dp_pd_event_work);
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-core.h b/drivers/gpu/drm/rockchip/cdn-dp-core.h
index f57e296..46159b2 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-core.h
+++ b/drivers/gpu/drm/rockchip/cdn-dp-core.h
@@ -78,6 +78,7 @@ struct cdn_dp_device {
struct platform_device *audio_pdev;
struct work_struct event_work;
struct edid *edid;
+ struct drm_dp_aux aux;
struct mutex lock;
bool connected;
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-reg.c b/drivers/gpu/drm/rockchip/cdn-dp-reg.c
index eb3042c..979355d 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-reg.c
+++ b/drivers/gpu/drm/rockchip/cdn-dp-reg.c
@@ -221,7 +221,12 @@ static int cdn_dp_reg_write_bit(struct cdn_dp_device *dp, u16 addr,
sizeof(field), field);
}
-int cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr, u8 *data, u16 len)
+/*
+ * Returns the number of bytes transferred on success, or a negative
+ * error code on failure. -ETIMEDOUT is returned if mailbox message was
+ * not send successfully;
+ */
+ssize_t cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr, u8 *data, u16 len)
{
u8 msg[5], reg[5];
int ret;
@@ -247,24 +252,41 @@ int cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr, u8 *data, u16 len)
goto err_dpcd_read;
ret = cdn_dp_mailbox_read_receive(dp, data, len);
+ if (!ret)
+ return len;
err_dpcd_read:
+ DRM_DEV_ERROR(dp->dev, "dpcd read failed: %d\n", ret);
return ret;
}
-int cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr, u8 value)
+#define CDN_AUX_HEADER_SIZE 5
+#define CDN_AUX_MSG_SIZE 20
+/*
+ * Returns the number of bytes transferred on success, or a negative error
+ * code on failure. -ETIMEDOUT is returned if mailbox message was not send
+ * success; -EINVAL is returned if get the wrong data size after message
+ * is sent
+ */
+ssize_t cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr, u8 *data, u16 len)
{
- u8 msg[6], reg[5];
+ u8 msg[CDN_AUX_MSG_SIZE + CDN_AUX_HEADER_SIZE];
+ u8 reg[CDN_AUX_HEADER_SIZE];
int ret;
- msg[0] = 0;
- msg[1] = 1;
+ if (WARN_ON(len > CDN_AUX_MSG_SIZE) || WARN_ON(len <= 0))
+ return -EINVAL;
+
+ msg[0] = (len >> 8) & 0xff;
+ msg[1] = len & 0xff;
msg[2] = (addr >> 16) & 0xff;
msg[3] = (addr >> 8) & 0xff;
msg[4] = addr & 0xff;
- msg[5] = value;
+
+ memcpy(msg + CDN_AUX_HEADER_SIZE, data, len);
+
ret = cdn_dp_mailbox_send(dp, MB_MODULE_ID_DP_TX, DPTX_WRITE_DPCD,
- sizeof(msg), msg);
+ CDN_AUX_HEADER_SIZE + len, msg);
if (ret)
goto err_dpcd_write;
@@ -277,8 +299,12 @@ int cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr, u8 value)
if (ret)
goto err_dpcd_write;
- if (addr != (reg[2] << 16 | reg[3] << 8 | reg[4]))
+ if ((len != (reg[0] << 8 | reg[1])) ||
+ (addr != (reg[2] << 16 | reg[3] << 8 | reg[4]))) {
ret = -EINVAL;
+ } else {
+ return len;
+ }
err_dpcd_write:
if (ret)
@@ -286,6 +312,33 @@ int cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr, u8 value)
return ret;
}
+int cdn_dp_get_aux_status(struct cdn_dp_device *dp)
+{
+ u8 status;
+ int ret;
+
+ ret = cdn_dp_mailbox_send(dp, MB_MODULE_ID_DP_TX,
+ DPTX_GET_LAST_AUX_STAUS, 0, NULL);
+ if (ret)
+ goto err_get_hpd;
+
+ ret = cdn_dp_mailbox_validate_receive(dp, MB_MODULE_ID_DP_TX,
+ DPTX_GET_LAST_AUX_STAUS,
+ sizeof(status));
+ if (ret)
+ goto err_get_hpd;
+
+ ret = cdn_dp_mailbox_read_receive(dp, &status, sizeof(status));
+ if (ret)
+ goto err_get_hpd;
+
+ return status;
+
+err_get_hpd:
+ DRM_DEV_ERROR(dp->dev, "get aux status failed: %d\n", ret);
+ return ret;
+}
+
int cdn_dp_load_firmware(struct cdn_dp_device *dp, const u32 *i_mem,
u32 i_size, const u32 *d_mem, u32 d_size)
{
diff --git a/drivers/gpu/drm/rockchip/cdn-dp-reg.h b/drivers/gpu/drm/rockchip/cdn-dp-reg.h
index c4bbb4a83..6580b11 100644
--- a/drivers/gpu/drm/rockchip/cdn-dp-reg.h
+++ b/drivers/gpu/drm/rockchip/cdn-dp-reg.h
@@ -328,6 +328,13 @@
#define GENERAL_BUS_SETTINGS 0x03
#define GENERAL_TEST_ACCESS 0x04
+/* AUX status*/
+#define AUX_STATUS_ACK 0
+#define AUX_STATUS_NACK 1
+#define AUX_STATUS_DEFER 2
+#define AUX_STATUS_SINK_ERROR 3
+#define AUX_STATUS_BUS_ERROR 4
+
#define DPTX_SET_POWER_MNG 0x00
#define DPTX_SET_HOST_CAPABILITIES 0x01
#define DPTX_GET_EDID 0x02
@@ -469,8 +476,11 @@ int cdn_dp_set_host_cap(struct cdn_dp_device *dp, u8 lanes, bool flip);
int cdn_dp_event_config(struct cdn_dp_device *dp);
u32 cdn_dp_get_event(struct cdn_dp_device *dp);
int cdn_dp_get_hpd_status(struct cdn_dp_device *dp);
-int cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr, u8 value);
-int cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr, u8 *data, u16 len);
+ssize_t cdn_dp_dpcd_write(struct cdn_dp_device *dp, u32 addr,
+ u8 *data, u16 len);
+ssize_t cdn_dp_dpcd_read(struct cdn_dp_device *dp, u32 addr,
+ u8 *data, u16 len);
+int cdn_dp_get_aux_status(struct cdn_dp_device *dp);
int cdn_dp_get_edid_block(void *dp, u8 *edid,
unsigned int block, size_t length);
int cdn_dp_train_link(struct cdn_dp_device *dp);
--
2.7.4
^ permalink raw reply related
* [PATCH v3 4/5] ARM: perf: Allow the use of the PMUv3 driver on 32bit ARM
From: Vladimir Murzin @ 2018-05-21 9:34 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180518143913.26306-5-marc.zyngier@arm.com>
On 18/05/18 15:39, Marc Zyngier wrote:
> +static inline int read_pmuver(void)
> +{
> + /* PMUVers is not a signed field */
> + u32 dfr0 = read_cpuid_ext(CPUID_EXT_DFR0);
> + return (dfr0 >> 24) & 0xf;
> +}
Should we rule out versions prior v3 here or in __armv8pmu_probe_pmu()?
Thanks
Vladimir
^ permalink raw reply
* [PATCH v9 06/11] arm64: kexec_file: allow for loading Image-format kernel
From: AKASHI Takahiro @ 2018-05-21 9:32 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <4a8409dc-27b3-1ddc-0427-0ca55edcb893@arm.com>
James,
I haven't commented on this email.
On Tue, May 15, 2018 at 06:14:37PM +0100, James Morse wrote:
> Hi Akashi,
>
> On 15/05/18 06:13, AKASHI Takahiro wrote:
> > On Fri, May 11, 2018 at 06:07:06PM +0100, James Morse wrote:
> >> On 07/05/18 08:21, AKASHI Takahiro wrote:
> >>> On Tue, May 01, 2018 at 06:46:11PM +0100, James Morse wrote:
> >>>> On 25/04/18 07:26, AKASHI Takahiro wrote:
> >>>>> This patch provides kexec_file_ops for "Image"-format kernel. In this
> >>>>> implementation, a binary is always loaded with a fixed offset identified
> >>>>> in text_offset field of its header.
> >>
> >>>>> diff --git a/arch/arm64/include/asm/kexec.h b/arch/arm64/include/asm/kexec.h
> >>>>> index e4de1223715f..3cba4161818a 100644
> >>>>> --- a/arch/arm64/include/asm/kexec.h
> >>>>> +++ b/arch/arm64/include/asm/kexec.h
>
> >>>> Could we check branch_code is non-zero, and text-offset points within image-size?
> >>>
> >>> We could do it, but I don't think this check is very useful.
> >>>
> >>>>
> >>>> We could check that this platform supports the page-size/endian config that this
> >>>> Image was built with... We get a message from the EFI stub if the page-size
> >>>> can't be supported, it would be nice to do the same here (as we can).
> >>>
> >>> There is no restriction on page-size or endianness for kexec.
> >>
> >> No, but it won't boot if the hardware doesn't support it. The kernel will spin
> >> at a magic address that is, difficult, to debug without JTAG. The bug report
> >> will be "it didn't boot".
> >
> > OK.
> > Added sanity checks for cpu features, endianness as well as page size.
> >
> >>
> >>> What will be the purpose of this check?
> >>
> >> These values are in the header so that the bootloader can check them, then print
> >> a meaningful error. Here, kexec_file_load() is playing the part of the bootloader.
>
> >> I'm assuming kexec_file_load() can only be used to kexec linux... unlike regular
> >> kexec. Is this where I'm going wrong?
>
> Trying to work this out for myself: we can't support any UEFI application as we
> can't give it the boot-services environment, so I'm pretty sure
> kexec_file_load() must be linux-specific.
>
> Can we state somewhere that we only expect arm64 linux to be booted with
> kexec_file_load()? Its not clear from the kconfig text, which refers to kexec,
> which explicitly states it can boot other OS. But for kexec_file_load() we're
> following the kernel's booting.txt.
While I don't know anything about requirements in booting other OS's nor
if we can boot them even with kexec, I agree that kexec_file_load is a more
limited form of booting mechanism. I will add some statement in Kconfig.
> >>>>> diff --git a/arch/arm64/kernel/kexec_image.c b/arch/arm64/kernel/kexec_image.c
> >>>>> new file mode 100644
> >>>>> index 000000000000..4dd524ad6611
> >>>>> --- /dev/null
> >>>>> +++ b/arch/arm64/kernel/kexec_image.c
> >>>>> @@ -0,0 +1,79 @@
> >>>>
> >>>>> +static void *image_load(struct kimage *image,
> >>>>> + char *kernel, unsigned long kernel_len,
> >>>>> + char *initrd, unsigned long initrd_len,
> >>>>> + char *cmdline, unsigned long cmdline_len)
> >>>>> +{
> >>>>> + struct kexec_buf kbuf;
> >>>>> + struct arm64_image_header *h = (struct arm64_image_header *)kernel;
> >>>>> + unsigned long text_offset;
> >>>>> + int ret;
> >>>>> +
> >>>>> + /* Load the kernel */
> >>>>> + kbuf.image = image;
> >>>>> + kbuf.buf_min = 0;
> >>>>> + kbuf.buf_max = ULONG_MAX;
> >>>>> + kbuf.top_down = false;
> >>>>> +
> >>>>> + kbuf.buffer = kernel;
> >>>>> + kbuf.bufsz = kernel_len;
> >>>>> + kbuf.memsz = le64_to_cpu(h->image_size);
> >>>>> + text_offset = le64_to_cpu(h->text_offset);
> >>>>> + kbuf.buf_align = SZ_2M;
> >>>>
> >>>>> + /* Adjust kernel segment with TEXT_OFFSET */
> >>>>> + kbuf.memsz += text_offset;
> >>>>> +
> >>>>> + ret = kexec_add_buffer(&kbuf);
> >>>>> + if (ret)
> >>>>> + goto out;
> >>>>> +
> >>>>> + image->arch.kern_segment = image->nr_segments - 1;
> >>>>
> >>>> You only seem to use kern_segment here, and in load_other_segments() called
> >>>> below. Could it not be a local variable passed in? Instead of arch-specific data
> >>>> we keep forever?
> >>>
> >>> No, kern_segment is also used in load_other_segments() in machine_kexec_file.c.
> >>> To optimize memory hole allocation logic in locate_mem_hole_callback(),
> >>> we need to know the exact range of kernel image (start and end).
> >>
> >> That's the second user. My badly-made point is one calls the other, but passes
> >> the data via some until-kexec lifetime struct. (its not important, just an
> >> indicator this worked differently in the past and hasn't been cleaned up).
> >> I meant something like [0].
> >
> > OK, but instead of adding kern_seg, I want to change the interface to:
> >
> > | extern int load_other_segments(struct kimage *image,
> > | unsigned long kernel_load_addr, unsigned long kernel_size,
> > | char *initrd, unsigned long initrd_len,
> > | char *cmdline, unsigned long cmdline_len);
> >
> > This way, we will in future be able to address an issue I mentioned in
> > my previous e-mail. (If we support vmlinux, the kernel occupies two segments
> > for text and data, respectively.)
>
> Aha, its not from old-stuff, its for future-stuff!
I have vmlinux patch, but it is very unlikely for me to submit it :)
Thanks,
-Takahiro AKASHI
>
> James
^ permalink raw reply
* [PATCH v9 02/12] drivers: base: cacheinfo: setup DT cache properties early
From: Sudeep Holla @ 2018-05-21 9:27 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAHp75VfEYcPdECmDDOd8CLBBXGpcwSUGQRr0x8VTb1-7j51_0Q@mail.gmail.com>
On 18/05/18 22:50, Andy Shevchenko wrote:
> On Thu, May 17, 2018 at 6:47 PM, Sudeep Holla <sudeep.holla@arm.com> wrote:
>
>> Is below patch does what you were looking for ?
>
> Somewhat.
> See below for some minors.
>
Thanks
>> of_property_read_u64 searches for a property in a device node and read
>> a 64-bit value from it. Instead of using of_get_property to get the
>> property and then read 64-bit value using of_read_number, we can make
>> use of of_property_read_u64.
>
> Suggested-by?
>
Yes indeed, added it locally after I sent out this patch. Will send out
a proper patch soon.
>> Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
>
>
>> - cache_size = of_get_property(np, propname, NULL);
>> - if (cache_size)
>> - this_leaf->size = of_read_number(cache_size, 1);
>> + if (!of_property_read_u64(np, propname, &cache_size))
>> + this_leaf->size = cache_size;
>
> I suppose it's something like this
>
> ret = of_property_...(..., &this_leaf->VAR);
> if (ret)
> warning / set default / etc
OK, I do prefer this but once I was told not to use structure elements
directly like that, but should be harmless in this particular case, will
do so.
--
Regards,
Sudeep
^ permalink raw reply
* [PATCH v8 10/15] cpufreq: Add Kryo CPU scaling driver
From: Viresh Kumar @ 2018-05-21 9:05 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <000501d3f0e2$23500c00$69f02400$@codeaurora.org>
On 21-05-18, 12:00, ilialin at codeaurora.org wrote:
> Final version (addressing Russel's comment as well):
Sorry, can't review it like this. At least you should be posting your
diff here and you also need to do that from a sane email client like
mutt, which wouldn't auto-fix/update the code. Doing it from gmail or
thunderbird will ofcourse screw it.
Or a simple way is to send the patch again (alone) using in-reply-to
field.
--
viresh
^ permalink raw reply
* [PATCH v8 10/15] cpufreq: Add Kryo CPU scaling driver
From: ilialin at codeaurora.org @ 2018-05-21 9:00 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180521044938.bnr2sdkmvdorfxqm@vireshk-i7>
Final version (addressing Russel's comment as well):
// SPDX-License-Identifier: GPL-2.0
/*
* Copyright (c) 2018, The Linux Foundation. All rights reserved.
*/
/*
* In Certain QCOM SoCs like apq8096 and msm8996 that have KRYO processors,
* the CPU frequency subset and voltage value of each OPP varies
* based on the silicon variant in use. Qualcomm Process Voltage Scaling
Tables
* defines the voltage and frequency value based on the msm-id in SMEM
* and speedbin blown in the efuse combination.
* The qcom-cpufreq-kryo driver reads the msm-id and efuse value from the
SoC
* to provide the OPP framework with required information.
* This is used to determine the voltage and frequency value for each OPP of
* operating-points-v2 table when it is parsed by the OPP framework.
*/
#include <linux/cpu.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/nvmem-consumer.h>
#include <linux/of.h>
#include <linux/platform_device.h>
#include <linux/pm_opp.h>
#include <linux/slab.h>
#include <linux/soc/qcom/smem.h>
#define MSM_ID_SMEM 137
#define SILVER_LEAD 0
#define GOLD_LEAD 2
enum _msm_id {
MSM8996V3 = 0xF6ul,
APQ8096V3 = 0x123ul,
MSM8996SG = 0x131ul,
APQ8096SG = 0x138ul,
};
enum _msm8996_version {
MSM8996_V3,
MSM8996_SG,
NUM_OF_MSM8996_VERSIONS,
};
static enum _msm8996_version __init qcom_cpufreq_kryo_get_msm_id(void)
{
size_t len;
u32 *msm_id;
enum _msm8996_version version;
msm_id = qcom_smem_get(QCOM_SMEM_HOST_ANY, MSM_ID_SMEM, &len);
/* The first 4 bytes are format, next to them is the actual msm-id
*/
msm_id++;
switch ((enum _msm_id)*msm_id) {
case MSM8996V3:
case APQ8096V3:
version = MSM8996_V3;
break;
case MSM8996SG:
case APQ8096SG:
version = MSM8996_SG;
break;
default:
version = NUM_OF_MSM8996_VERSIONS;
}
return version;
}
static int __init qcom_cpufreq_kryo_driver_init(void)
{
struct device *cpu_dev_silver, *cpu_dev_gold;
struct opp_table *opp_silver, *opp_gold;
enum _msm8996_version msm8996_version;
struct nvmem_cell *speedbin_nvmem;
struct platform_device *pdev;
struct device_node *np;
u8 *speedbin;
u32 versions;
size_t len;
int ret;
cpu_dev_silver = get_cpu_device(SILVER_LEAD);
if (NULL == cpu_dev_silver)
return -ENODEV;
cpu_dev_gold = get_cpu_device(SILVER_LEAD);
if (NULL == cpu_dev_gold)
return -ENODEV;
msm8996_version = qcom_cpufreq_kryo_get_msm_id();
if (NUM_OF_MSM8996_VERSIONS == msm8996_version) {
dev_err(cpu_dev_silver, "Not Snapdragon 820/821!");
return -ENODEV;
}
np = dev_pm_opp_of_get_opp_desc_node(cpu_dev_silver);
if (IS_ERR(np))
return PTR_ERR(np);
if (!of_device_is_compatible(np, "operating-points-v2-kryo-cpu")) {
ret = -ENOENT;
goto free_np;
}
speedbin_nvmem = of_nvmem_cell_get(np, NULL);
if (IS_ERR(speedbin_nvmem)) {
ret = PTR_ERR(speedbin_nvmem);
dev_err(cpu_dev_silver, "Could not get nvmem cell: %d\n",
ret);
goto free_np;
}
speedbin = nvmem_cell_read(speedbin_nvmem, &len);
nvmem_cell_put(speedbin_nvmem);
switch (msm8996_version) {
case MSM8996_V3:
versions = 1 << (unsigned int)(*speedbin);
break;
case MSM8996_SG:
versions = 1 << ((unsigned int)(*speedbin) + 4);
break;
default:
BUG();
break;
}
opp_silver =
dev_pm_opp_set_supported_hw(cpu_dev_silver,&versions,1);
if (IS_ERR(opp_silver)) {
dev_err(cpu_dev_silver, "Failed to set supported
hardware\n");
ret = PTR_ERR(opp_silver);
goto free_np;
}
opp_gold = dev_pm_opp_set_supported_hw(cpu_dev_gold,&versions,1);
if (IS_ERR(opp_gold)) {
dev_err(cpu_dev_gold, "Failed to set supported hardware\n");
ret = PTR_ERR(opp_gold);
goto free_opp_silver;
}
pdev = platform_device_register_simple("cpufreq-dt", -1, NULL, 0);
if (!IS_ERR(pdev))
return 0;
ret = PTR_ERR(pdev);
dev_err(cpu_dev_silver, "Failed to register platform device\n");
dev_pm_opp_put_supported_hw(opp_gold);
free_opp_silver:
dev_pm_opp_put_supported_hw(opp_silver);
free_np:
of_node_put(np);
return ret;
}
late_initcall(qcom_cpufreq_kryo_driver_init);
MODULE_DESCRIPTION("Qualcomm Technologies, Inc. Kryo CPUfreq driver");
MODULE_LICENSE("GPL v2");
> -----Original Message-----
> From: Viresh Kumar <viresh.kumar@linaro.org>
> Sent: Monday, May 21, 2018 07:50
> To: ilialin at codeaurora.org
> Cc: mturquette at baylibre.com; sboyd at kernel.org; robh at kernel.org;
> mark.rutland at arm.com; nm at ti.com; lgirdwood at gmail.com;
> broonie at kernel.org; andy.gross at linaro.org; david.brown at linaro.org;
> catalin.marinas at arm.com; will.deacon at arm.com; rjw at rjwysocki.net; linux-
> clk at vger.kernel.org; devicetree at vger.kernel.org; linux-
> kernel at vger.kernel.org; linux-pm at vger.kernel.org; linux-arm-
> msm at vger.kernel.org; linux-soc at vger.kernel.org; linux-arm-
> kernel at lists.infradead.org; rnayak at codeaurora.org;
> amit.kucheria at linaro.org; nicolas.dechesne at linaro.org;
> celster at codeaurora.org; tfinkel at codeaurora.org
> Subject: Re: [PATCH v8 10/15] cpufreq: Add Kryo CPU scaling driver
>
> On 19-05-18, 14:45, ilialin at codeaurora.org wrote:
> > Hi Viresh,
> >
> > If I send patches in reply, it will produce new patches, instead of
> > answers in the thread. Please find below the file dump.
>
> There is one email from you which appears to be just fine and appears to
be
> in reply to this thread only. Maybe its your email client that screwed it
up for
> you ? Things look good in mutt.
>
> --
> viresh
^ permalink raw reply
* [RFT v2 4/4] coresight: Document for CoreSight trace disassembler
From: Leo Yan @ 2018-05-21 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526892748-326-1-git-send-email-leo.yan@linaro.org>
This commit documents CoreSight trace disassembler usage and gives
example for it.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
---
Documentation/trace/coresight.txt | 52 +++++++++++++++++++++++++++++++++++++++
1 file changed, 52 insertions(+)
diff --git a/Documentation/trace/coresight.txt b/Documentation/trace/coresight.txt
index 6f0120c..b8f2359 100644
--- a/Documentation/trace/coresight.txt
+++ b/Documentation/trace/coresight.txt
@@ -381,3 +381,55 @@ sort example is from the AutoFDO tutorial (https://gcc.gnu.org/wiki/AutoFDO/Tuto
$ taskset -c 2 ./sort_autofdo
Bubble sorting array of 30000 elements
5806 ms
+
+
+Tracing data disassembler
+-------------------------
+
+'perf script' supports to use script to parse tracing packet and rely on
+'objdump' for disassembled lines, this can convert tracing data to readable
+program execution flow for easily reviewing tracing data.
+
+The CoreSight trace disassembler is located in the folder:
+tools/perf/scripts/python/arm-cs-trace-disasm.py. This script support below
+options:
+
+ -d, --objdump: Set path to objdump executable, this option is
+ mandatory.
+ -k, --vmlinux: Set path to vmlinux file.
+ -v, --verbose: Enable debugging log, after enable this option the
+ script dumps every event data.
+
+Below is one example for using python script to dump CoreSight trace
+disassembler:
+
+ $ perf script -s arm-cs-trace-disasm.py -i perf.data \
+ -F cpu,event,ip,addr,sym -- -d objdump -k ./vmlinux > cs-disasm.log
+
+Below is one example for the disassembler log:
+
+ARM CoreSight Trace Data Assembler Dump
+ ffff000008a5f2dc <etm4_enable_hw+0x344>:
+ ffff000008a5f2dc: 340000a0 cbz w0, ffff000008a5f2f0 <etm4_enable_hw+0x358>
+ ffff000008a5f2f0 <etm4_enable_hw+0x358>:
+ ffff000008a5f2f0: f9400260 ldr x0, [x19]
+ ffff000008a5f2f4: d5033f9f dsb sy
+ ffff000008a5f2f8: 913ec000 add x0, x0, #0xfb0
+ ffff000008a5f2fc: b900001f str wzr, [x0]
+ ffff000008a5f300: f9400bf3 ldr x19, [sp, #16]
+ ffff000008a5f304: a8c27bfd ldp x29, x30, [sp], #32
+ ffff000008a5f308: d65f03c0 ret
+ ffff000008a5fa18 <etm4_enable+0x1b0>:
+ ffff000008a5fa18: 14000025 b ffff000008a5faac <etm4_enable+0x244>
+ ffff000008a5faac <etm4_enable+0x244>:
+ ffff000008a5faac: b9406261 ldr w1, [x19, #96]
+ ffff000008a5fab0: 52800015 mov w21, #0x0 // #0
+ ffff000008a5fab4: f901ca61 str x1, [x19, #912]
+ ffff000008a5fab8: 2a1503e0 mov w0, w21
+ ffff000008a5fabc: 3940e261 ldrb w1, [x19, #56]
+ ffff000008a5fac0: f901ce61 str x1, [x19, #920]
+ ffff000008a5fac4: a94153f3 ldp x19, x20, [sp, #16]
+ ffff000008a5fac8: a9425bf5 ldp x21, x22, [sp, #32]
+ ffff000008a5facc: a94363f7 ldp x23, x24, [sp, #48]
+ ffff000008a5fad0: a8c47bfd ldp x29, x30, [sp], #64
+ ffff000008a5fad4: d65f03c0 ret
--
2.7.4
^ permalink raw reply related
* [RFT v2 3/4] perf script python: Add script for CoreSight trace disassembler
From: Leo Yan @ 2018-05-21 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526892748-326-1-git-send-email-leo.yan@linaro.org>
This commit adds python script to parse CoreSight tracing event and
use command 'objdump' for disassembled lines, finally we can generate
readable program execution flow for reviewing tracing data.
The script receives CoreSight tracing packet with below format:
+------------+------------+------------+
packet(n): | addr | ip | cpu |
+------------+------------+------------+
packet(n+1): | addr | ip | cpu |
+------------+------------+------------+
packet::ip is the last address of current branch instruction and
packet::addr presents the start address of the next coming branch
instruction. So for one branch instruction which starts in packet(n),
its execution flow starts from packet(n)::addr and it stops at
packet(n+1)::ip. As results we need to combine the two continuous
packets to generate the instruction range, this is the rationale for the
script implementation:
[ sample(n)::addr .. sample(n+1)::ip ]
Credits to Tor Jeremiassen who have written the script skeleton and
provides the ideas for reading symbol file according to build-id,
creating memory map for dso and basic packet handling. Mathieu Poirier
contributed fixes for build-id and memory map bugs. The detailed
development history for this script you can find from [1]. Based on Tor
and Mathieu work, the script is updated samples handling for the
corrected sample format. Another minor enhancement is to support for
without build-id case, the script can parse kernel symbols with option
'-k' for vmlinux file path.
[1] https://github.com/Linaro/perf-opencsd/commits/perf-opencsd-v4.15/tools/perf/scripts/python/cs-trace-disasm.py
Co-authored-by: Tor Jeremiassen <tor@ti.com>
Co-authored-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
---
tools/perf/scripts/python/arm-cs-trace-disasm.py | 234 +++++++++++++++++++++++
1 file changed, 234 insertions(+)
create mode 100644 tools/perf/scripts/python/arm-cs-trace-disasm.py
diff --git a/tools/perf/scripts/python/arm-cs-trace-disasm.py b/tools/perf/scripts/python/arm-cs-trace-disasm.py
new file mode 100644
index 0000000..58de36f
--- /dev/null
+++ b/tools/perf/scripts/python/arm-cs-trace-disasm.py
@@ -0,0 +1,234 @@
+# arm-cs-trace-disasm.py: ARM CoreSight Trace Dump With Disassember
+# SPDX-License-Identifier: GPL-2.0
+#
+# Tor Jeremiassen <tor@ti.com> is original author who wrote script
+# skeleton, Mathieu Poirier <mathieu.poirier@linaro.org> contributed
+# fixes for build-id and memory map; Leo Yan <leo.yan@linaro.org>
+# updated the packet parsing with new samples format.
+
+import os
+import sys
+import re
+from subprocess import *
+from optparse import OptionParser, make_option
+
+# Command line parsing
+
+option_list = [
+ # formatting options for the bottom entry of the stack
+ make_option("-k", "--vmlinux", dest="vmlinux_name",
+ help="Set path to vmlinux file"),
+ make_option("-d", "--objdump", dest="objdump_name",
+ help="Set path to objdump executable file"),
+ make_option("-v", "--verbose", dest="verbose",
+ action="store_true", default=False,
+ help="Enable debugging log")
+]
+
+parser = OptionParser(option_list=option_list)
+(options, args) = parser.parse_args()
+
+if (options.objdump_name == None):
+ sys.exit("No objdump executable file specified - use -d or --objdump option")
+
+# Initialize global dicts and regular expression
+
+build_ids = dict()
+mmaps = dict()
+disasm_cache = dict()
+cpu_data = dict()
+disasm_re = re.compile("^\s*([0-9a-fA-F]+):")
+disasm_func_re = re.compile("^\s*([0-9a-fA-F]+)\s\<.*\>:")
+cache_size = 32*1024
+prev_cpu = -1
+
+def parse_buildid():
+ global build_ids
+
+ buildid_regex = "([a-fA-f0-9]+)[ \t]([^ \n]+)"
+ buildid_re = re.compile(buildid_regex)
+
+ results = check_output(["perf", "buildid-list"]).split('\n');
+ for line in results:
+ m = buildid_re.search(line)
+ if (m == None):
+ continue;
+
+ id_name = m.group(2)
+ id_num = m.group(1)
+
+ if (id_name == "[kernel.kallsyms]") :
+ append = "/kallsyms"
+ elif (id_name == "[vdso]") :
+ append = "/vdso"
+ else:
+ append = "/elf"
+
+ build_ids[id_name] = os.environ['PERF_BUILDID_DIR'] + \
+ "/" + id_name + "/" + id_num + append;
+ # Replace duplicate slash chars to single slash char
+ build_ids[id_name] = build_ids[id_name].replace('//', '/', 1)
+
+ if ((options.vmlinux_name == None) and ("[kernel.kallsyms]" in build_ids)):
+ print "kallsyms cannot be used to dump assembler"
+
+ # Set vmlinux path to replace kallsyms file, if without buildid we still
+ # can use vmlinux to prase kernel symbols
+ if ((options.vmlinux_name != None)):
+ build_ids['[kernel.kallsyms]'] = options.vmlinux_name;
+
+def parse_mmap():
+ global mmaps
+
+ # Check mmap for PERF_RECORD_MMAP and PERF_RECORD_MMAP2
+ mmap_regex = "PERF_RECORD_MMAP.* -?[0-9]+/[0-9]+: \[(0x[0-9a-fA-F]+)\((0x[0-9a-fA-F]+)\).*:\s.*\s(\S*)"
+ mmap_re = re.compile(mmap_regex)
+
+ results = check_output("perf script --show-mmap-events | fgrep PERF_RECORD_MMAP", shell=True).split('\n')
+ for line in results:
+ m = mmap_re.search(line)
+ if (m != None):
+ if (m.group(3) == '[kernel.kallsyms]_text'):
+ dso = '[kernel.kallsyms]'
+ else:
+ dso = m.group(3)
+
+ start = int(m.group(1),0)
+ end = int(m.group(1),0) + int(m.group(2),0)
+ mmaps[dso] = [start, end]
+
+def find_dso_mmap(addr):
+ global mmaps
+
+ for key, value in mmaps.items():
+ if (addr >= value[0] and addr < value[1]):
+ return key
+
+ return None
+
+def read_disam(dso, start_addr, stop_addr):
+ global mmaps
+ global build_ids
+
+ addr_range = start_addr + ":" + stop_addr;
+
+ # Don't let the cache get too big, clear it when it hits max size
+ if (len(disasm_cache) > cache_size):
+ disasm_cache.clear();
+
+ try:
+ disasm_output = disasm_cache[addr_range];
+ except:
+ try:
+ fname = build_ids[dso];
+ except KeyError:
+ sys.exit("cannot find symbol file for " + dso)
+
+ disasm = [ options.objdump_name, "-d", "-z",
+ "--start-address="+start_addr,
+ "--stop-address="+stop_addr, fname ]
+
+ disasm_output = check_output(disasm).split('\n')
+ disasm_cache[addr_range] = disasm_output;
+
+ return disasm_output
+
+def dump_disam(dso, start_addr, stop_addr, check_svc):
+ for line in read_disam(dso, start_addr, stop_addr):
+ m = disasm_func_re.search(line)
+ if (m != None):
+ print "\t",line
+ continue
+
+ m = disasm_re.search(line)
+ if (m == None):
+ continue;
+
+ print "\t",line
+
+ if ((check_svc == True) and "svc" in line):
+ return
+
+def dump_packet(sample):
+ print "Packet = { cpu: 0x%d addr: 0x%x phys_addr: 0x%x ip: 0x%x " \
+ "pid: %d tid: %d period: %d time: %d }" % \
+ (sample['cpu'], sample['addr'], sample['phys_addr'], \
+ sample['ip'], sample['pid'], sample['tid'], \
+ sample['period'], sample['time'])
+
+def trace_begin():
+ print 'ARM CoreSight Trace Data Assembler Dump'
+ parse_buildid()
+ parse_mmap()
+
+def trace_end():
+ print 'End'
+
+def trace_unhandled(event_name, context, event_fields_dict):
+ print ' '.join(['%s=%s'%(k,str(v))for k,v in sorted(event_fields_dict.items())])
+
+def process_event(param_dict):
+ global cache_size
+ global options
+ global prev_cpu
+
+ sample = param_dict["sample"]
+
+ if (options.verbose == True):
+ dump_packet(sample)
+
+ # If period doesn't equal to 1, this packet is for instruction sample
+ # packet, we need drop this synthetic packet.
+ if (sample['period'] != 1):
+ print "Skip synthetic instruction sample"
+ return
+
+ cpu = format(sample['cpu'], "d");
+
+ # Initialize CPU data if it's empty, and directly return back
+ # if this is the first tracing event for this CPU.
+ if (cpu_data.get(str(cpu) + 'addr') == None):
+ cpu_data[str(cpu) + 'addr'] = format(sample['addr'], "#x")
+ prev_cpu = cpu
+ return
+
+ # The format for packet is:
+ #
+ # +------------+------------+------------+
+ # sample_prev: | addr | ip | cpu |
+ # +------------+------------+------------+
+ # sample_next: | addr | ip | cpu |
+ # +------------+------------+------------+
+ #
+ # We need to combine the two continuous packets to get the instruction
+ # range for sample_prev::cpu:
+ #
+ # [ sample_prev::addr .. sample_next::ip ]
+ #
+ # For this purose, sample_prev::addr is stored into cpu_data structure
+ # and read back for 'start_addr' when the new packet comes, and we need
+ # to use sample_next::ip to calculate 'stop_addr', plusing extra 4 for
+ # 'stop_addr' is for the sake of objdump so the final assembler dump can
+ # include last instruction for sample_next::ip.
+
+ start_addr = cpu_data[str(prev_cpu) + 'addr']
+ stop_addr = format(sample['ip'] + 4, "#x")
+
+ # Sanity checking dso for start_addr and stop_addr
+ prev_dso = find_dso_mmap(int(start_addr, 0))
+ next_dso = find_dso_mmap(int(stop_addr, 0))
+
+ # If cannot find dso so cannot dump assembler, bail out
+ if (prev_dso == None or next_dso == None):
+ print "Address range [ %s .. %s ]: failed to find dso" % (start_addr, stop_addr)
+ prev_cpu = cpu
+ return
+ elif (prev_dso != next_dso):
+ print "Address range [ %s .. %s ]: isn't in same dso" % (start_addr, stop_addr)
+ prev_cpu = cpu
+ return
+
+ dump_disam(prev_dso, start_addr, stop_addr, False)
+
+ cpu_data[str(cpu) + 'addr'] = format(sample['addr'], "#x")
+ prev_cpu = cpu
--
2.7.4
^ permalink raw reply related
* [RFT v2 2/4] perf script python: Add addr into perf sample dict
From: Leo Yan @ 2018-05-21 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526892748-326-1-git-send-email-leo.yan@linaro.org>
ARM CoreSight auxtrace uses 'sample->addr' to record the target address
for branch instructions, so the data of 'sample->addr' is required for
tracing data analysis.
This commit collects data of 'sample->addr' into perf sample dict,
finally can be used for python script for parsing event.
Signed-off-by: Leo Yan <leo.yan@linaro.org>
---
tools/perf/util/scripting-engines/trace-event-python.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/tools/perf/util/scripting-engines/trace-event-python.c b/tools/perf/util/scripting-engines/trace-event-python.c
index 10dd5fc..7f8afac 100644
--- a/tools/perf/util/scripting-engines/trace-event-python.c
+++ b/tools/perf/util/scripting-engines/trace-event-python.c
@@ -531,6 +531,8 @@ static PyObject *get_perf_sample_dict(struct perf_sample *sample,
PyLong_FromUnsignedLongLong(sample->period));
pydict_set_item_string_decref(dict_sample, "phys_addr",
PyLong_FromUnsignedLongLong(sample->phys_addr));
+ pydict_set_item_string_decref(dict_sample, "addr",
+ PyLong_FromUnsignedLongLong(sample->addr));
set_sample_read_in_dict(dict_sample, sample, evsel);
pydict_set_item_string_decref(dict, "sample", dict_sample);
--
2.7.4
^ permalink raw reply related
* [RFT v2 1/4] perf cs-etm: Generate sample for missed packets
From: Leo Yan @ 2018-05-21 8:52 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526892748-326-1-git-send-email-leo.yan@linaro.org>
Commit e573e978fb12 ("perf cs-etm: Inject capabilitity for CoreSight
traces") reworks the samples generation flow from CoreSight trace to
match the correct format so Perf report tool can display the samples
properly. But the change has side effect for packet handling, it only
generate samples when 'prev_packet->last_instr_taken_branch' is true,
this results in the start tracing packet and exception packets are
dropped.
This patch checks extra two conditions for complete samples:
- If 'prev_packet->sample_type' is zero we can use this condition to
get to know this is the start tracing packet; for this case, the start
packet's end_addr is zero as well so we need to handle it in the
function cs_etm__last_executed_instr();
- If 'prev_packet->exc' is true, we can know the previous packet is
exception handling packet so need to generate sample for exception
flow.
Fixes: e573e978fb12 ("perf cs-etm: Inject capabilitity for CoreSight traces")
Cc: Mike Leach <mike.leach@arm.com>
Cc: Robert Walker <robert.walker@arm.com>
Cc: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Leo Yan <leo.yan@linaro.org>
---
tools/perf/util/cs-etm.c | 35 ++++++++++++++++++++++++++++-------
1 file changed, 28 insertions(+), 7 deletions(-)
diff --git a/tools/perf/util/cs-etm.c b/tools/perf/util/cs-etm.c
index 822ba91..378953b 100644
--- a/tools/perf/util/cs-etm.c
+++ b/tools/perf/util/cs-etm.c
@@ -495,6 +495,13 @@ static inline void cs_etm__reset_last_branch_rb(struct cs_etm_queue *etmq)
static inline u64 cs_etm__last_executed_instr(struct cs_etm_packet *packet)
{
/*
+ * The packet is the start tracing packet if the end_addr is zero,
+ * returns 0 for this case.
+ */
+ if (!packet->end_addr)
+ return 0;
+
+ /*
* The packet records the execution range with an exclusive end address
*
* A64 instructions are constant size, so the last executed
@@ -897,13 +904,27 @@ static int cs_etm__sample(struct cs_etm_queue *etmq)
etmq->period_instructions = instrs_over;
}
- if (etm->sample_branches &&
- etmq->prev_packet &&
- etmq->prev_packet->sample_type == CS_ETM_RANGE &&
- etmq->prev_packet->last_instr_taken_branch) {
- ret = cs_etm__synth_branch_sample(etmq);
- if (ret)
- return ret;
+ if (etm->sample_branches && etmq->prev_packet) {
+ bool generate_sample = false;
+
+ /* Generate sample for start tracing packet */
+ if (etmq->prev_packet->sample_type == 0)
+ generate_sample = true;
+
+ /* Generate sample for exception packet */
+ if (etmq->prev_packet->exc == true)
+ generate_sample = true;
+
+ /* Generate sample for normal branch packet */
+ if (etmq->prev_packet->sample_type == CS_ETM_RANGE &&
+ etmq->prev_packet->last_instr_taken_branch)
+ generate_sample = true;
+
+ if (generate_sample) {
+ ret = cs_etm__synth_branch_sample(etmq);
+ if (ret)
+ return ret;
+ }
}
if (etm->sample_branches || etm->synth_opts.last_branch) {
--
2.7.4
^ permalink raw reply related
* [RFT v2 0/4] Perf script: Add python script for CoreSight trace disassembler
From: Leo Yan @ 2018-05-21 8:52 UTC (permalink / raw)
To: linux-arm-kernel
This patch series is to support for using 'perf script' for CoreSight
trace disassembler, for this purpose this patch series adds a new
python script to parse CoreSight tracing event and use command 'objdump'
for disassembled lines, finally this can generate readable program
execution flow for reviewing tracing data.
Patch 0001 is one fixing patch to generate samples for the start packet
and exception packets.
Patch 0002 is the prerequisite to add addr into sample dict, so this
value can be used by python script to analyze instruction range.
Patch 0003 is to add python script for trace disassembler.
Patch 0004 is to add doc to explain python script usage and give
example for it.
This patch series has been rebased on acme git tree [1] with the last
commit 19422a9f2a3b ("perf tools: Fix kernel_start for PTI on x86") and
tested on Hikey (ARM64 octa CA53 cores).
In this version the script has no dependency on ARM64 platform and is
expected to support ARM32 platform, but I am lacking ARM32 platform for
testing on it, so firstly upstream to support ARM64 platform.
This patch series is firstly to support 'per-thread' recording tracing
data, but we also need to verify the script can dump trace disassembler
CPU wide tracing and kernel panic kdump tracing data. I also verified
this patch series which can work with kernel panic kdump tracing data,
because Mathieu is working on CPU wide tracing related work, so after
this we need to retest for CPU wide tracing and kdump tracing to ensure
the python script can handle well for all cases.
You are very welcome to test the script in this patch series, your
testing result and suggestion are very valuable to perfect this script
to cover more cases.
Changes from v1:
* According to Mike and Rob suggestion, add the fixing to generate samples
for the start packet and exception packets.
* Simplify the python script to remove the exception prediction algorithm,
we can rely on the sane exception packets for disassembler.
[1] https://git.kernel.org/pub/scm/linux/kernel/git/acme/linux.git
Leo Yan (4):
perf cs-etm: Generate sample for missed packets
perf script python: Add addr into perf sample dict
perf script python: Add script for CoreSight trace disassembler
coresight: Document for CoreSight trace disassembler
Documentation/trace/coresight.txt | 52 +++++
tools/perf/scripts/python/arm-cs-trace-disasm.py | 234 +++++++++++++++++++++
tools/perf/util/cs-etm.c | 35 ++-
.../util/scripting-engines/trace-event-python.c | 2 +
4 files changed, 316 insertions(+), 7 deletions(-)
create mode 100644 tools/perf/scripts/python/arm-cs-trace-disasm.py
--
2.7.4
^ permalink raw reply
* [PATCH V2 2/3] clk: imx7d: correct enet clock CCGR registers
From: Stefan Agner @ 2018-05-21 8:14 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <AM3PR04MB1315417C51882B554AEBC617F5950@AM3PR04MB1315.eurprd04.prod.outlook.com>
On 21.05.2018 04:35, Anson Huang wrote:
> Hi, Stefan
>
> Anson Huang
> Best Regards!
>
>
>> -----Original Message-----
>> From: Stefan Agner [mailto:stefan at agner.ch]
>> Sent: Friday, May 18, 2018 9:02 PM
>> To: Anson Huang <anson.huang@nxp.com>
>> Cc: shawnguo at kernel.org; kernel at pengutronix.de; Fabio Estevam
>> <fabio.estevam@nxp.com>; robh+dt at kernel.org; mark.rutland at arm.com;
>> mturquette at baylibre.com; sboyd at kernel.org; Adriana Reus
>> <adriana.reus@nxp.com>; rui.silva at linaro.org; dl-linux-imx
>> <linux-imx@nxp.com>; linux-arm-kernel at lists.infradead.org;
>> devicetree at vger.kernel.org; linux-kernel at vger.kernel.org;
>> linux-clk at vger.kernel.org
>> Subject: Re: [PATCH V2 2/3] clk: imx7d: correct enet clock CCGR registers
>>
>> On 18.05.2018 03:01, Anson Huang wrote:
>> > Correct enet clock gates as below:
>> >
>> > CCGR6: IMX7D_ENET_AXI_ROOT_CLK (enet1 and enet2 bus clocks)
>> > CCGR112: IMX7D_ENET1_TIME_ROOT_CLK, IMX7D_ENET1_IPG_ROOT_CLK
>> > CCGR113: IMX7D_ENET2_TIME_ROOT_CLK, IMX7D_ENET2_IPG_ROOT_CLK
>> >
>> > Just rename unused IMX7D_ENETx_REF_ROOT_CLK for
>> > IMX7D_ENETx_IPG_ROOT_CLK instead of adding new clocks.
>>
>> Are you sure that IMX7D_ENETx_REF_ROOT_CLK are not used?
>>
>> I understand that the reference manual does not a gate at 0x44e0...
>>
>> But in a earlier revision of our Colibri iMX7 we actually used clock out, and
>> referenced this clock to enable the reference clock (see also:
>> https://emea01.safelinks.protection.outlook.com/?url=https%3A%2F%2Fpatch
>> work.kernel.org%2Fpatch%2F9211371%2F&data=02%7C01%7CAnson.Huang%
>> 40nxp.com%7Cea0856a68d8e4b921ba608d5bcbf9c02%7C686ea1d3bc2b4c6fa
>> 92cd99c5c301635%7C0%7C1%7C636622453508888330&sdata=rEhwj0innLDc
>> AEgxJyqd5vtG3SNVS05r2hEFvSc%2BQQs%3D&reserved=0).
>>
>> I guess if the gate really does not exist, then we should/would have to set
>> IMX7D_ENET1_REF_ROOT_DIV to use the SoC provided ref clock.
>>
>> --
>> Stefan
>
> I looked into the RTL and also checked with our design team, they confirm that
> there is no CCGR78(0x44e0) and CCGR80(0x4500) on i.MX7D, the register offset
> are there, but no hardware wire connection for them. That is why they did NOT
> list them in Reference Manual. So I think we can remove them.
>
> For your case of using them as clock input, maybe clock tree auto use its parent
> IMX7D_ENETx_REF_ROOT_DIV which is existing, so it works.
That make sense.
The change looks good to me.
Reviewed-by: Stefan Agner <stefan@agner.ch>
--
Stefan
>
> Anson.
>
>>
>> >
>> > Based on Andy Duan's patch from the NXP kernel tree.
>> >
>> > Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
>> > ---
>> > drivers/clk/imx/clk-imx7d.c | 10 ++++++----
>> > include/dt-bindings/clock/imx7d-clock.h | 4 ++--
>> > 2 files changed, 8 insertions(+), 6 deletions(-)
>> >
>> > diff --git a/drivers/clk/imx/clk-imx7d.c b/drivers/clk/imx/clk-imx7d.c
>> > index 23d5090a..d4936b9 100644
>> > --- a/drivers/clk/imx/clk-imx7d.c
>> > +++ b/drivers/clk/imx/clk-imx7d.c
>> > @@ -26,6 +26,8 @@ static u32 share_count_sai1; static u32
>> > share_count_sai2; static u32 share_count_sai3; static u32
>> > share_count_nand;
>> > +static u32 share_count_enet1;
>> > +static u32 share_count_enet2;
>> >
>> > static const struct clk_div_table test_div_table[] = {
>> > { .val = 3, .div = 1, },
>> > @@ -805,6 +807,10 @@ static void __init imx7d_clocks_init(struct
>> > device_node *ccm_node)
>> > clks[IMX7D_MIPI_DSI_ROOT_CLK] = imx_clk_gate4("mipi_dsi_root_clk",
>> > "mipi_dsi_post_div", base + 0x4650, 0);
>> > clks[IMX7D_MIPI_CSI_ROOT_CLK] = imx_clk_gate4("mipi_csi_root_clk",
>> > "mipi_csi_post_div", base + 0x4640, 0);
>> > clks[IMX7D_MIPI_DPHY_ROOT_CLK] =
>> imx_clk_gate4("mipi_dphy_root_clk",
>> > "mipi_dphy_post_div", base + 0x4660, 0);
>> > + clks[IMX7D_ENET1_IPG_ROOT_CLK] =
>> > imx_clk_gate2_shared2("enet1_ipg_root_clk", "enet_axi_post_div", base
>> > + 0x4700, 0, &share_count_enet1);
>> > + clks[IMX7D_ENET1_TIME_ROOT_CLK] =
>> > imx_clk_gate2_shared2("enet1_time_root_clk", "enet1_time_post_div",
>> > base + 0x4700, 0, &share_count_enet1);
>> > + clks[IMX7D_ENET2_IPG_ROOT_CLK] =
>> > imx_clk_gate2_shared2("enet2_ipg_root_clk", "enet_axi_post_div", base
>> > + 0x4710, 0, &share_count_enet2);
>> > + clks[IMX7D_ENET2_TIME_ROOT_CLK] =
>> > imx_clk_gate2_shared2("enet2_time_root_clk", "enet2_time_post_div",
>> > base + 0x4710, 0, &share_count_enet2);
>> > clks[IMX7D_SAI1_ROOT_CLK] = imx_clk_gate2_shared2("sai1_root_clk",
>> > "sai1_post_div", base + 0x48c0, 0, &share_count_sai1);
>> > clks[IMX7D_SAI1_IPG_CLK] = imx_clk_gate2_shared2("sai1_ipg_clk",
>> > "ipg_root_clk", base + 0x48c0, 0, &share_count_sai1);
>> > clks[IMX7D_SAI2_ROOT_CLK] = imx_clk_gate2_shared2("sai2_root_clk",
>> > "sai2_post_div", base + 0x48d0, 0, &share_count_sai2); @@ -812,10
>> > +818,6 @@ static void __init imx7d_clocks_init(struct device_node
>> > *ccm_node)
>> > clks[IMX7D_SAI3_ROOT_CLK] = imx_clk_gate2_shared2("sai3_root_clk",
>> > "sai3_post_div", base + 0x48e0, 0, &share_count_sai3);
>> > clks[IMX7D_SAI3_IPG_CLK] = imx_clk_gate2_shared2("sai3_ipg_clk",
>> > "ipg_root_clk", base + 0x48e0, 0, &share_count_sai3);
>> > clks[IMX7D_SPDIF_ROOT_CLK] = imx_clk_gate4("spdif_root_clk",
>> > "spdif_post_div", base + 0x44d0, 0);
>> > - clks[IMX7D_ENET1_REF_ROOT_CLK] =
>> imx_clk_gate4("enet1_ref_root_clk",
>> > "enet1_ref_post_div", base + 0x44e0, 0);
>> > - clks[IMX7D_ENET1_TIME_ROOT_CLK] =
>> > imx_clk_gate4("enet1_time_root_clk", "enet1_time_post_div", base +
>> > 0x44f0, 0);
>> > - clks[IMX7D_ENET2_REF_ROOT_CLK] =
>> imx_clk_gate4("enet2_ref_root_clk",
>> > "enet2_ref_post_div", base + 0x4500, 0);
>> > - clks[IMX7D_ENET2_TIME_ROOT_CLK] =
>> > imx_clk_gate4("enet2_time_root_clk", "enet2_time_post_div", base +
>> > 0x4510, 0);
>> > clks[IMX7D_EIM_ROOT_CLK] = imx_clk_gate4("eim_root_clk",
>> > "eim_post_div", base + 0x4160, 0);
>> > clks[IMX7D_NAND_RAWNAND_CLK] =
>> > imx_clk_gate2_shared2("nand_rawnand_clk", "nand_root_clk", base +
>> > 0x4140, 0, &share_count_nand);
>> > clks[IMX7D_NAND_USDHC_BUS_RAWNAND_CLK] =
>> > imx_clk_gate2_shared2("nand_usdhc_rawnand_clk",
>> "nand_usdhc_root_clk",
>> > base + 0x4140, 0, &share_count_nand); diff --git
>> > a/include/dt-bindings/clock/imx7d-clock.h
>> > b/include/dt-bindings/clock/imx7d-clock.h
>> > index b2325d3e2..0d67f53 100644
>> > --- a/include/dt-bindings/clock/imx7d-clock.h
>> > +++ b/include/dt-bindings/clock/imx7d-clock.h
>> > @@ -168,7 +168,7 @@
>> > #define IMX7D_SPDIF_ROOT_SRC 155
>> > #define IMX7D_SPDIF_ROOT_CG 156
>> > #define IMX7D_SPDIF_ROOT_DIV 157
>> > -#define IMX7D_ENET1_REF_ROOT_CLK 158
>> > +#define IMX7D_ENET1_IPG_ROOT_CLK 158
>> > #define IMX7D_ENET1_REF_ROOT_SRC 159
>> > #define IMX7D_ENET1_REF_ROOT_CG 160
>> > #define IMX7D_ENET1_REF_ROOT_DIV 161
>> > @@ -176,7 +176,7 @@
>> > #define IMX7D_ENET1_TIME_ROOT_SRC 163
>> > #define IMX7D_ENET1_TIME_ROOT_CG 164
>> > #define IMX7D_ENET1_TIME_ROOT_DIV 165
>> > -#define IMX7D_ENET2_REF_ROOT_CLK 166
>> > +#define IMX7D_ENET2_IPG_ROOT_CLK 166
>> > #define IMX7D_ENET2_REF_ROOT_SRC 167
>> > #define IMX7D_ENET2_REF_ROOT_CG 168
>> > #define IMX7D_ENET2_REF_ROOT_DIV 169
^ permalink raw reply
* [PATCH 12/15] drm/sun4i: Add support for second clock parent to DW HDMI PHY clk driver
From: Maxime Ripard @ 2018-05-21 8:12 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180519183127.2718-13-jernej.skrabec@siol.net>
On Sat, May 19, 2018 at 08:31:24PM +0200, Jernej Skrabec wrote:
> Expand HDMI PHY clock driver to support second clock parent.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h | 6 +-
> drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c | 29 ++++++-
> drivers/gpu/drm/sun4i/sun8i_hdmi_phy_clk.c | 90 ++++++++++++++++------
> 3 files changed, 98 insertions(+), 27 deletions(-)
>
> diff --git a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h
> index 801a17222762..aadbe0a10b0c 100644
> --- a/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h
> +++ b/drivers/gpu/drm/sun4i/sun8i_dw_hdmi.h
> @@ -98,7 +98,8 @@
> #define SUN8I_HDMI_PHY_PLL_CFG1_LDO2_EN BIT(29)
> #define SUN8I_HDMI_PHY_PLL_CFG1_LDO1_EN BIT(28)
> #define SUN8I_HDMI_PHY_PLL_CFG1_HV_IS_33 BIT(27)
> -#define SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL BIT(26)
> +#define SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL_MSK BIT(26)
> +#define SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL_SHIFT 26
> #define SUN8I_HDMI_PHY_PLL_CFG1_PLLEN BIT(25)
> #define SUN8I_HDMI_PHY_PLL_CFG1_LDO_VSET(x) ((x) << 22)
> #define SUN8I_HDMI_PHY_PLL_CFG1_UNKNOWN(x) ((x) << 20)
> @@ -190,6 +191,7 @@ void sun8i_hdmi_phy_remove(struct sun8i_dw_hdmi *hdmi);
> void sun8i_hdmi_phy_init(struct sun8i_hdmi_phy *phy);
> const struct dw_hdmi_phy_ops *sun8i_hdmi_phy_get_ops(void);
>
> -int sun8i_phy_clk_create(struct sun8i_hdmi_phy *phy, struct device *dev);
> +int sun8i_phy_clk_create(struct sun8i_hdmi_phy *phy, struct device *dev,
> + bool second_parent);
>
> #endif /* _SUN8I_DW_HDMI_H_ */
> diff --git a/drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c b/drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c
> index deba47ed69d8..7a911f0a3ae3 100644
> --- a/drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c
> +++ b/drivers/gpu/drm/sun4i/sun8i_hdmi_phy.c
> @@ -183,7 +183,13 @@ static int sun8i_hdmi_phy_config_h3(struct dw_hdmi *hdmi,
> regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_ANA_CFG1_REG,
> SUN8I_HDMI_PHY_ANA_CFG1_TXEN_MASK, 0);
>
> - regmap_write(phy->regs, SUN8I_HDMI_PHY_PLL_CFG1_REG, pll_cfg1_init);
> + /*
> + * NOTE: We have to be careful not to overwrite PHY parent
> + * clock selection bit and clock divider.
> + */
> + regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_PLL_CFG1_REG,
> + ~SUN8I_HDMI_PHY_PLL_CFG1_CKIN_SEL_MSK,
> + pll_cfg1_init);
It feels like it belongs in a separate patch.
> regmap_update_bits(phy->regs, SUN8I_HDMI_PHY_PLL_CFG2_REG,
> (u32)~SUN8I_HDMI_PHY_PLL_CFG2_PREDIV_MSK,
> pll_cfg2_init);
> @@ -352,6 +358,10 @@ static void sun8i_hdmi_phy_init_h3(struct sun8i_hdmi_phy *phy)
> SUN8I_HDMI_PHY_ANA_CFG3_SCLEN |
> SUN8I_HDMI_PHY_ANA_CFG3_SDAEN);
>
> + /* reset PLL clock configuration */
> + regmap_write(phy->regs, SUN8I_HDMI_PHY_PLL_CFG1_REG, 0);
> + regmap_write(phy->regs, SUN8I_HDMI_PHY_PLL_CFG2_REG, 0);
> +
Ditto,
> +
> + /*
> + * Even though HDMI PHY clock doesn't have enable/disable
> + * handlers, we have to enable it. Otherwise it could happen
> + * that parent PLL is not enabled by clock framework in a
> + * highly unlikely event when parent PLL is used solely for
> + * HDMI PHY clock.
> + */
> + clk_prepare_enable(phy->clk_phy);
The implementation of the clock doesn't really matter in our API
usage. If we're using a clock, we have to call
clk_prepare_enable. That's documented everywhere, and mentionning how
the clock is implemented is an abstraction leakage and it's
irrelevant. I'd simply remove the comment here.
And it should be in a separate patch as well.
Maxime
--
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20180521/d5f8520a/attachment.sig>
^ permalink raw reply
* [PATCH 0/2] get rid of Kconfig symbol MACH_MESON8B
From: Jerome Brunet @ 2018-05-21 8:12 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180520172353.19256-1-martin.blumenstingl@googlemail.com>
On Sun, 2018-05-20 at 19:23 +0200, Martin Blumenstingl wrote:
> as noted by Kevin [0] there are two Kconfig symbols which only differ
> in their Kconfig help text and the list of .dtbs that are being built.
> the goal of this small series is to get rid of the unnecessary
> MACH_MESON8B Kconfig symbol by merging it into MACH_MESON8.
>
>
> [0] http://lists.infradead.org/pipermail/linux-amlogic/2018-May/007342.html
>
> Martin Blumenstingl (2):
> ARM: dts: meson: build the Meson8b .dtbs with MACH_MESON8
> ARM: meson: merge Kconfig symbol MACH_MESON8B into MACH_MESON8
>
> arch/arm/boot/dts/Makefile | 5 ++---
> arch/arm/mach-meson/Kconfig | 9 +--------
> 2 files changed, 3 insertions(+), 11 deletions(-)
>
For the series:
Reviewed-by: Jerome Brunet <jbrunet@baylibre.com>
^ permalink raw reply
* [PATCH 06/15] drm/sun4i: tcon: Add support for tcon-top
From: Maxime Ripard @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180519183127.2718-7-jernej.skrabec@siol.net>
On Sat, May 19, 2018 at 08:31:18PM +0200, Jernej Skrabec wrote:
> If SoC has TCON TOP unit, it has to be configured from TCON, since it
> has all information needed. Additionally, if it is TCON TV, it must also
> enable bus gate inside TCON TOP unit.
Why?
> Add support for such TCONs.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> drivers/gpu/drm/sun4i/sun4i_tcon.c | 28 ++++++++++++++++++++++++++++
> drivers/gpu/drm/sun4i/sun4i_tcon.h | 8 ++++++++
> 2 files changed, 36 insertions(+)
>
> diff --git a/drivers/gpu/drm/sun4i/sun4i_tcon.c b/drivers/gpu/drm/sun4i/sun4i_tcon.c
> index 08747fc3ee71..e0c562ce1c22 100644
> --- a/drivers/gpu/drm/sun4i/sun4i_tcon.c
> +++ b/drivers/gpu/drm/sun4i/sun4i_tcon.c
> @@ -688,6 +688,16 @@ static int sun4i_tcon_init_clocks(struct device *dev,
> dev_err(dev, "Couldn't get the TCON bus clock\n");
> return PTR_ERR(tcon->clk);
> }
> +
> + if (tcon->quirks->needs_tcon_top && tcon->quirks->has_channel_1) {
> + tcon->top_clk = devm_clk_get(dev, "tcon-top");
> + if (IS_ERR(tcon->top_clk)) {
> + dev_err(dev, "Couldn't get the TCON TOP bus clock\n");
> + return PTR_ERR(tcon->top_clk);
> + }
> + clk_prepare_enable(tcon->top_clk);
> + }
> +
> clk_prepare_enable(tcon->clk);
>
> if (tcon->quirks->has_channel_0) {
> @@ -712,6 +722,7 @@ static int sun4i_tcon_init_clocks(struct device *dev,
> static void sun4i_tcon_free_clocks(struct sun4i_tcon *tcon)
> {
> clk_disable_unprepare(tcon->clk);
> + clk_disable_unprepare(tcon->top_clk);
> }
>
> static int sun4i_tcon_init_irq(struct device *dev,
> @@ -980,6 +991,23 @@ static int sun4i_tcon_bind(struct device *dev, struct device *master,
> tcon->id = engine->id;
> tcon->quirks = of_device_get_match_data(dev);
>
> + if (tcon->quirks->needs_tcon_top) {
> + struct device_node *np;
> +
> + np = of_parse_phandle(dev->of_node, "allwinner,tcon-top", 0);
> + if (np) {
> + struct platform_device *pdev;
> +
> + pdev = of_find_device_by_node(np);
> + if (pdev)
> + tcon->tcon_top = platform_get_drvdata(pdev);
> + of_node_put(np);
> +
> + if (!tcon->tcon_top)
> + return -EPROBE_DEFER;
> + }
> + }
> +
I might have missed it, but I've not seen the bindings additions for
that property. This shouldn't really be done that way anyway, instead
of using a direct phandle, you should be using the of-graph, with the
TCON-top sitting where it belongs in the flow of data.
Maxime
--
Maxime Ripard, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 833 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20180521/9e6fce45/attachment.sig>
^ permalink raw reply
* [PATCH V3 8/8] dt-bindings: stm32: add compatible for syscon
From: Christophe Roullier @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526890046-10565-1-git-send-email-christophe.roullier@st.com>
This patch describes syscon DT bindings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
Documentation/devicetree/bindings/arm/stm32.txt | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/arm/stm32.txt b/Documentation/devicetree/bindings/arm/stm32.txt
index 6808ed9..e46ebad 100644
--- a/Documentation/devicetree/bindings/arm/stm32.txt
+++ b/Documentation/devicetree/bindings/arm/stm32.txt
@@ -8,3 +8,8 @@ using one of the following compatible strings:
st,stm32f746
st,stm32h743
st,stm32mp157
+
+Required nodes:
+- syscon: the soc bus node must have a system controller node pointing to the
+ global control registers, with the compatible string
+ "st,stm32mp157-syscfg", "syscon";
--
1.9.1
^ permalink raw reply related
* [PATCH V3 7/8] ARM: dts: stm32: add support of ethernet on stm32mp157c-ev1
From: Christophe Roullier @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526890046-10565-1-git-send-email-christophe.roullier@st.com>
MAC is connected to a PHY in RGMII mode.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
arch/arm/boot/dts/stm32mp157c-ev1.dts | 20 ++++++++++++++++++++
1 file changed, 20 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c-ev1.dts b/arch/arm/boot/dts/stm32mp157c-ev1.dts
index 57e6dbc..a7fee5c 100644
--- a/arch/arm/boot/dts/stm32mp157c-ev1.dts
+++ b/arch/arm/boot/dts/stm32mp157c-ev1.dts
@@ -17,5 +17,25 @@
aliases {
serial0 = &uart4;
+ ethernet0 = ðernet0;
+ };
+};
+
+ðernet0 {
+ status = "okay";
+ pinctrl-0 = <ðernet0_rgmii_pins_a>;
+ pinctrl-1 = <ðernet0_rgmii_pins_sleep_a>;
+ pinctrl-names = "default", "sleep";
+ phy-mode = "rgmii";
+ max-speed = <1000>;
+ phy-handle = <&phy0>;
+
+ mdio0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ compatible = "snps,dwmac-mdio";
+ phy0: ethernet-phy at 0 {
+ reg = <0>;
+ };
};
};
--
1.9.1
^ permalink raw reply related
* [PATCH V3 6/8] net: stmmac: add dwmac-4.20a compatible
From: Christophe Roullier @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526890046-10565-1-git-send-email-christophe.roullier@st.com>
Manage dwmac-4.20a version from synopsys
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c | 3 ++-
1 file changed, 2 insertions(+), 1 deletion(-)
diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
index ebd3e5f..6d141f3 100644
--- a/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
+++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
@@ -472,7 +472,8 @@ struct plat_stmmacenet_data *
}
if (of_device_is_compatible(np, "snps,dwmac-4.00") ||
- of_device_is_compatible(np, "snps,dwmac-4.10a")) {
+ of_device_is_compatible(np, "snps,dwmac-4.10a") ||
+ of_device_is_compatible(np, "snps,dwmac-4.20a")) {
plat->has_gmac4 = 1;
plat->has_gmac = 0;
plat->pmt = 1;
--
1.9.1
^ permalink raw reply related
* [PATCH V3 5/8] ARM: dts: stm32: Add ethernet dwmac on stm32mp1
From: Christophe Roullier @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526890046-10565-1-git-send-email-christophe.roullier@st.com>
Add Ethernet support (Synopsys MAC IP 4.20a) on stm32mp1 SOC.
Enable feature supported by the stmmac driver, such as TSO.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
arch/arm/boot/dts/stm32mp157c.dtsi | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index dbc0e707..99cc94c 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -179,5 +179,35 @@
clocks = <&rcc USART1_K>;
status = "disabled";
};
+
+ stmmac_axi_config_0: stmmac-axi-config {
+ snps,wr_osr_lmt = <0x7>;
+ snps,rd_osr_lmt = <0x7>;
+ snps,blen = <0 0 0 0 16 8 4>;
+ };
+
+ ethernet0: ethernet at 5800a000 {
+ compatible = "st,stm32mp1-dwmac", "snps,dwmac-4.20a";
+ reg = <0x5800a000 0x2000>;
+ reg-names = "stmmaceth";
+ interrupts-extended = <&intc GIC_SPI 61 IRQ_TYPE_NONE>;
+ interrupt-names = "macirq";
+ clock-names = "stmmaceth",
+ "mac-clk-tx",
+ "mac-clk-rx",
+ "ethstp",
+ "syscfg-clk";
+ clocks = <&rcc ETHMAC>,
+ <&rcc ETHTX>,
+ <&rcc ETHRX>,
+ <&rcc ETHSTP>,
+ <&rcc SYSCFG>;
+ st,syscon = <&syscfg 0x4>;
+ snps,mixed-burst;
+ snps,pbl = <2>;
+ snps,axi-config = <&stmmac_axi_config_0>;
+ snps,tso;
+ status = "disabled";
+ };
};
};
--
1.9.1
^ permalink raw reply related
* [PATCH V3 4/8] ARM: dts: stm32: Add syscfg on stm32mp1
From: Christophe Roullier @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526890046-10565-1-git-send-email-christophe.roullier@st.com>
System configuration controller is mainly used to manage
the compensation cell and other IOs and system related
settings.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
arch/arm/boot/dts/stm32mp157c.dtsi | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157c.dtsi b/arch/arm/boot/dts/stm32mp157c.dtsi
index bc3eddc..dbc0e707 100644
--- a/arch/arm/boot/dts/stm32mp157c.dtsi
+++ b/arch/arm/boot/dts/stm32mp157c.dtsi
@@ -167,6 +167,11 @@
#reset-cells = <1>;
};
+ syscfg: system-config at 50020000 {
+ compatible = "st,stm32mp157-syscfg", "syscon";
+ reg = <0x50020000 0x400>;
+ };
+
usart1: serial at 5c000000 {
compatible = "st,stm32h7-uart";
reg = <0x5c000000 0x400>;
--
1.9.1
^ permalink raw reply related
* [PATCH V3 3/8] ARM: dts: stm32: add ethernet pins to stm32mp157c
From: Christophe Roullier @ 2018-05-21 8:07 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1526890046-10565-1-git-send-email-christophe.roullier@st.com>
Add ethernet pins on stm32mp157c.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
---
arch/arm/boot/dts/stm32mp157-pinctrl.dtsi | 46 +++++++++++++++++++++++++++++++
1 file changed, 46 insertions(+)
diff --git a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
index 6f044100..cf83eb244 100644
--- a/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp157-pinctrl.dtsi
@@ -158,6 +158,52 @@
bias-disable;
};
};
+
+ ethernet0_rgmii_pins_a: rgmii-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('A', 2, AF11)>, /* ETH_MDIO */
+ <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <3>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('B', 0, AF11)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('B', 1, AF11)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+ bias-disable;
+ };
+ };
+
+ ethernet0_rgmii_pins_sleep_a: rgmii-sleep-0 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+ <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('B', 0, ANALOG)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('B', 1, ANALOG)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+ };
+ };
};
pinctrl_z: pin-controller-z {
--
1.9.1
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox