* [PATCH 6/9] ARM: dts: wheat: Drop MTD partitioning from DT
From: Marek Vasut @ 2018-05-30 10:13 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180528093602.eb36j34bbfzmpmw2@verge.net.au>
On 05/28/2018 11:36 AM, Simon Horman wrote:
> On Mon, May 28, 2018 at 10:54:57AM +0200, Geert Uytterhoeven wrote:
>> Hi Simon,
>>
>> On Mon, May 28, 2018 at 10:41 AM, Simon Horman <horms@verge.net.au> wrote:
>>> On Thu, May 24, 2018 at 04:52:59PM +0200, Marek Vasut wrote:
>>>> On 05/23/2018 08:25 AM, Geert Uytterhoeven wrote:
>>>>> On Wed, May 23, 2018 at 12:01 AM, Marek Vasut <marek.vasut@gmail.com> wrote:
>>>>>> On 05/22/2018 04:43 PM, Geert Uytterhoeven wrote:
>>>>>>> On Tue, May 22, 2018 at 2:02 PM, Marek Vasut <marek.vasut@gmail.com> wrote:
>>>>>>>> Drop the MTD partitioning from DT, since it does not describe HW
>>>>>>>> and to give way to a more flexible kernel command line partition
>>>>>>>> passing.
>>>>>>>>
>>>>>>>> To retain the original partitioning, assure you have enabled
>>>>>>>> CONFIG_MTD_CMDLINE_PARTS in your kernel config and add the
>>>>>>>> following to your kernel command line:
>>>>>>>>
>>>>>>>> mtdparts=spi0.0:256k at 0(loader),4096k(user),-(flash)
>>>>>>>
>>>>>>> I think the "@0" can be dropped, as it's optional?
>>>>>>> 4m?
>>>>>>
>>>>>> My take on this is that the loader is actually at offset 0x0 of the MTD
>>>>>> device and we explicitly state that in the mtdparts to anchor the first
>>>>>> partition within the MTD device and all the other partitions are at
>>>>>> offset +(sum of the sizes of all partitions listed before the current
>>>>>> one) relative to that first partition.
>>>>>
>>>>> Where is this explicitly states for the first partition?
>>>>>
>>>>>> Removing the @0 feels fragile at best and it seems to depend on the
>>>>>> current behavior of the code.
>>>>>
>>>>> Better, it also depends on the documented behavior:
>>>>>
>>>>> Documentation/admin-guide/kernel-parameters.txt refers to
>>>>> drivers/mtd/cmdlinepart.c, which states:
>>>>>
>>>>> * <offset> := standard linux memsize
>>>>> * if omitted the part will immediately follow the previous part
>>>>> * or 0 if the first part
>>>>>
>>>>> None of the examples listed there or under the MTD_CMDLINE_PARTS Kconfig
>>>>> help text, or in a defconfig bundled with the kernel, use @0 for the first
>>>>> partition.
>>>>
>>>> I think this is exceptionally fragile and dangerous to depend on this,
>>>> but so be it.
>>>
>>> Could you respin with this change?
>>>
>>> I would also like to ask for another change, in light of recent
>>> feedback from Olof Johansson ("Re: [GIT PULL] Renesas ARM64 Based SoC DT
>>> Updates for v4.18").
>>>
>>> Please consolidate the dts patches into a single patch?
>>
>> I think it's better to keep them split, as each commit description mentions
>> what needs to be passed on the kernel command line for the corresponding
>> board.
>>
>> Combining it in a single patch makes it much harder to extract this information.
>> Unless you're fine with a list:
>>
>> koelsch: ...
>> wheat: mtdparts=spi0.0:256k at 0(loader),4096k(user),-(flash)
>
> Lets try a list.
Reposted with a list, twice :/
--
Best regards,
Marek Vasut
^ permalink raw reply
* [RESEND PATCH] dmaengine: pxa: add a default requestor policy
From: Vinod @ 2018-05-30 10:25 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <874liqtgul.fsf@belgarion.home>
On 29-05-18, 21:13, Robert Jarzmik wrote:
> Vinod <vkoul@kernel.org> writes:
>
> > On 26-05-18, 11:54, Robert Jarzmik wrote:
> >> @@ -762,6 +762,8 @@ static void pxad_free_chan_resources(struct dma_chan *dchan)
> >> dma_pool_destroy(chan->desc_pool);
> >> chan->desc_pool = NULL;
> >>
> >> + chan->drcmr = (u32)-1;
> >
> > why not use U32_MAX for this?
> But of course, anything else you see ?
Nope that was the only one :)
--
~Vinod
^ permalink raw reply
* [PATCH v3 2/2] drm/nouveau: tegra: Detach from ARM DMA/IOMMU mapping
From: Robin Murphy @ 2018-05-30 10:30 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180530080345.2353-3-thierry.reding@gmail.com>
On 30/05/18 09:03, Thierry Reding wrote:
> From: Thierry Reding <treding@nvidia.com>
>
> Depending on the kernel configuration, early ARM architecture setup code
> may have attached the GPU to a DMA/IOMMU mapping that transparently uses
> the IOMMU to back the DMA API. Tegra requires special handling for IOMMU
> backed buffers (a special bit in the GPU's MMU page tables indicates the
> memory path to take: via the SMMU or directly to the memory controller).
> Transparently backing DMA memory with an IOMMU prevents Nouveau from
> properly handling such memory accesses and causes memory access faults.
>
> As a side-note: buffers other than those allocated in instance memory
> don't need to be physically contiguous from the GPU's perspective since
> the GPU can map them into contiguous buffers using its own MMU. Mapping
> these buffers through the IOMMU is unnecessary and will even lead to
> performance degradation because of the additional translation. One
> exception to this are compressible buffers which need large pages. In
> order to enable these large pages, multiple small pages will have to be
> combined into one large (I/O virtually contiguous) mapping via the
> IOMMU. However, that is a topic outside the scope of this fix and isn't
> currently supported. An implementation will want to explicitly create
> these large pages in the Nouveau driver, so detaching from a DMA/IOMMU
> mapping would still be required.
I wonder if it might make sense to have a hook in iommu_attach_device()
to notify the arch DMA API code when moving devices between unmanaged
and DMA ops domains? That seems like it might be the most low-impact way
to address the overall problem long-term.
> Signed-off-by: Thierry Reding <treding@nvidia.com>
> ---
> Changes in v3:
> - clarify the use of IOMMU mapping for compressible buffers
> - squash multiple patches into this
>
> drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c b/drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c
> index 78597da6313a..d0538af1b967 100644
> --- a/drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c
> +++ b/drivers/gpu/drm/nouveau/nvkm/engine/device/tegra.c
> @@ -105,6 +105,11 @@ nvkm_device_tegra_probe_iommu(struct nvkm_device_tegra *tdev)
> unsigned long pgsize_bitmap;
> int ret;
>
> +#if IS_ENABLED(CONFIG_ARM)
Wouldn't CONFIG_ARM_DMA_USE_IOMMU be even more appropriate?
> + /* make sure we can use the IOMMU exclusively */
> + arm_dma_iommu_detach_device(dev);
As before, I would just use the existing infrastructure the same way the
Exynos DRM driver currently does in __exynos_iommu_attach() (albeit
without then reattaching to another DMA ops mapping).
Robin.
> +#endif
> +
> if (!tdev->func->iommu_bit)
> return;
>
>
^ permalink raw reply
* [PATCH v4 1/2] regulator: dt-bindings: add QCOM RPMh regulator bindings
From: Mark Brown @ 2018-05-30 10:37 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAD=FV=VH0bTxPOmRr+jUyV0cGNQHLcwQTV9L-t0bxZOqD8FnHA@mail.gmail.com>
On Tue, May 29, 2018 at 10:23:20PM -0700, Doug Anderson wrote:
> > + qcom,drms-mode-max-microamps = <10000 1000000>;
> Things look pretty good to me now. I'm still hesitant about the whole
> need to list the modes twice (once using the unordered
> "regulator-allowed-modes" and once to match up against the ordered
> "qcom,drms-mode-max-microamps"). I'm also still of the opinion that
> the whole "drms-mode-max-microamps" ought to be a standard property
> (not a qcom specific one) and handled in the regulator core.
I'm confused as to why we are specifying the maximum current the device
can deliver in a given mode in the DT - surely that's a fixed property
of the hardware?
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 488 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20180530/a7eec198/attachment-0001.sig>
^ permalink raw reply
* [PATCH v5 2/2] arm64: signal: Report signal frame size to userspace via auxv
From: Dave Martin @ 2018-05-30 10:48 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180529204230.GG591@arm.com>
On Tue, May 29, 2018 at 09:42:31PM +0100, Will Deacon wrote:
> Hi Dave,
>
> Cheers for respinning this. Just one observation below, which I only just
> thought about.
>
> On Fri, May 25, 2018 at 04:17:08PM +0100, Dave Martin wrote:
> > Stateful CPU architecture extensions may require the signal frame
> > to grow to a size that exceeds the arch's MINSIGSTKSZ #define.
> > However, changing this #define is an ABI break.
> >
> > To allow userspace the option of determining the signal frame size
> > in a more forwards-compatible way, this patch adds a new auxv entry
> > tagged with AT_MINSIGSTKSZ, which provides the maximum signal frame
> > size that the process can observe during its lifetime.
> >
> > If AT_MINSIGSTKSZ is absent from the aux vector, the caller can
> > assume that the MINSIGSTKSZ #define is sufficient. This allows for
> > a consistent interface with older kernels that do not provide
> > AT_MINSIGSTKSZ.
> >
> > The idea is that libc could expose this via sysconf() or some
> > similar mechanism.
> >
> > There is deliberately no AT_SIGSTKSZ. The kernel knows nothing
> > about userspace's own stack overheads and should not pretend to
> > know.
>
> [...]
>
> > diff --git a/arch/arm64/include/asm/elf.h b/arch/arm64/include/asm/elf.h
> > index fac1c4d..8cf112b 100644
> > --- a/arch/arm64/include/asm/elf.h
> > +++ b/arch/arm64/include/asm/elf.h
> > @@ -121,6 +121,9 @@
> >
> > #ifndef __ASSEMBLY__
> >
> > +#include <linux/bug.h>
> > +#include <asm/processor.h> /* for signal_minsigstksz, used by ARCH_DLINFO */
> > +
> > typedef unsigned long elf_greg_t;
> >
> > #define ELF_NGREG (sizeof(struct user_pt_regs) / sizeof(elf_greg_t))
> > @@ -148,6 +151,14 @@ typedef struct user_fpsimd_state elf_fpregset_t;
> > do { \
> > NEW_AUX_ENT(AT_SYSINFO_EHDR, \
> > (elf_addr_t)current->mm->context.vdso); \
> > + \
> > + /* \
> > + * Should always be nonzero unless there's a kernel bug. \
> > + * If we haven't determined a sensible value to give to \
> > + * userspace, omit the entry: \
> > + */ \
> > + if (likely(signal_minsigstksz)) \
> > + NEW_AUX_ENT(AT_MINSIGSTKSZ, signal_minsigstksz); \
> > } while (0)
>
> I think this is the desired behaviour, but now I'm worried that we're forced
> to have AT_VECTOR_SIZE_ARCH defined as 2 and, whilst you're correct that the
> ELF loader deals with this gracefuly, the FDPIC loader looks a lot less
> robust (in particular, my reading is that it decrements the stack pointer
> and then pushes these entries in reverse order by overloading NEW_AUX_ENT).
config BINFMT_ELF_FDPIC
/* ... */
depends on (ARM || (SUPERH32 & !MMU) || C6X)
The FDPIC loader seems to assume it's 32-bit only and also looks broken
with regard to auxv:
/* force 16 byte _final_ alignment here for generality */
#define DLINFO_ITEMS 15
/* ... */
nr = 0;
csp -= 2 * sizeof(unsigned long);
NEW_AUX_ENT(AT_EXECFD, ...);
}
/* ... */
csp -= DLINFO_ITEMS * 2 * sizeof(unsigned long);
NEW_AUX_ENT(AT_HWCAP, ELF_HWCAP);
#ifdef ELF_HWCAP2
NEW_AUX_ENT(AT_HWCAP2, ELF_HWCAP2);
#endif
/* 14 more NEW_AUX_ENT() */
Looks like commit 2171364d1a92 ("powerpc: Add HWCAP2 aux entry") added
HWCAP2 without ensuring that space is reserved.
I can try to draft a patch to handle the auxv in a more sane way for
FDPIC, but either way I don't see that it should be relevant to arm64.
AT_IGNORE feels like a bit of a fig leaf, but it's harmless enough. I'm
happy to add it if you prefer.
Cheers
---Dave
^ permalink raw reply
* [PATCH v2 9/9] PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM domains
From: Ulf Hansson @ 2018-05-30 11:31 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <cc6f36ce-32b7-4b69-f9a9-98cf0b12a9d1@nvidia.com>
On 30 May 2018 at 11:19, Jon Hunter <jonathanh@nvidia.com> wrote:
> Hi Ulf,
>
> On 29/05/18 11:04, Ulf Hansson wrote:
>> The existing dev_pm_domain_attach() function, allows a single PM domain to
>> be attached per device. To be able to support devices that are partitioned
>> across multiple PM domains, let's introduce a new interface,
>> dev_pm_domain_attach_by_id().
>>
>> The dev_pm_domain_attach_by_id() returns a new allocated struct device with
>> the corresponding attached PM domain. This enables for example a driver to
>> operate on the new device from a power management point of view. The driver
>> may then also benefit from using the received device, to set up so called
>> device-links towards its original device. Depending on the situation, these
>> links may then be dynamically changed.
>
> I have given this series a go with Tegra updating the XHCI driver to make
> use of these new APIs. Good news it does appear to work fine for Tegra,
> however, initially when looking at the device_link_add() API ...
>
> /**
> * device_link_add - Create a link between two devices.
> * @consumer: Consumer end of the link.
> * @supplier: Supplier end of the link.
> * @flags: Link flags.
>
> ... I had assumed that the 'consumer' device would be the actual XHCI
> device (in the case of Tegra) and the 'supplier' device would be the new
> genpd device. However, this did not work and I got the following WARN on
> boot ...
>
> [ 2.050929] ---[ end trace eff0b5265e530c92 ]---
> [ 2.055567] WARNING: CPU: 2 PID: 1 at drivers/base/core.c:446 device_links_driver_bound+0xc0/0xd0
> [ 2.064422] Modules linked in:
> [ 2.067471] CPU: 2 PID: 1 Comm: swapper/0 Tainted: G W 4.17.0-rc7-next-20180529-00011-g4faf0dc0ebf3-dirty #32
> [ 2.078667] Hardware name: Google Pixel C (DT)
> [ 2.083101] pstate: 80000005 (Nzcv daif -PAN -UAO)
> [ 2.087881] pc : device_links_driver_bound+0xc0/0xd0
> [ 2.092832] lr : device_links_driver_bound+0x20/0xd0
>
> Switching the Tegra XHCI device to be the 'supplier' and genpd device to
> be the 'consumer' does work, but is this correct? Seems to be opposite to
It shall be the opposite. The Tegra XHCI device shall be the consumer.
> what I expected. Maybe I am missing something?
The problem you get is because the device returned from
dev_pm_domain_attach_by_id(), let's call it genpd_dev, doesn't have
the a driver.
You need to use a couple of device links flag, something like this:
link = device_link_add(dev, genpd_dev, DL_FLAG_STATELESS |
DL_FLAG_PM_RUNTIME | DL_FLAG_RPM_ACTIVE);
Moreover, you also need these commits, depending if you are running on
something else than Rafael's tree.
a0504aecba76 PM / runtime: Drop usage count for suppliers at device link removal
1e8378619841 PM / runtime: Fixup reference counting of device link
suppliers at probe
>
>> The new interface is typically called by drivers during their probe phase,
>> in case they manages devices which uses multiple PM domains. If that is the
>> case, the driver also becomes responsible of managing the detaching of the
>> PM domains, which typically should be done at the remove phase. Detaching
>> is done by calling the existing dev_pm_domain_detach() function and for
>> each of the received devices from dev_pm_domain_attach_by_id().
>>
>> Note, currently its only genpd that supports multiple PM domains per
>> device, but dev_pm_domain_attach_by_id() can easily by extended to cover
>> other PM domain types, if/when needed.
>>
>> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
>> ---
>>
>> Changes in v2:
>> - Fixed comments from Jon. Clarified function descriptions/changelog and
>> return ERR_PTR(-EEXIST) in case a PM domain is already assigned.
>> - Fix build error when CONFIG_PM is unset.
>>
>> ---
>> drivers/base/power/common.c | 43 ++++++++++++++++++++++++++++++++++---
>> include/linux/pm_domain.h | 7 ++++++
>> 2 files changed, 47 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/base/power/common.c b/drivers/base/power/common.c
>> index 7ae62b6355b8..5e5ea0c239de 100644
>> --- a/drivers/base/power/common.c
>> +++ b/drivers/base/power/common.c
>> @@ -116,14 +116,51 @@ int dev_pm_domain_attach(struct device *dev, bool power_on)
>> }
>> EXPORT_SYMBOL_GPL(dev_pm_domain_attach);
>>
>> +/**
>> + * dev_pm_domain_attach_by_id - Attach a device to one of its PM domains.
>> + * @dev: Device to attach.
>
> Nit ... I still don't think this is the device we are attaching to, but the
> device the PM domains are associated with. IOW we are using this device to
> lookup the PM domains.
Right. I forgot to update that part of the description.
What about:
dev_pm_domain_attach_by_id - Associate a device with one of its PM domains.
@dev: The device used to lookup the PM domain.
>
>> + * @index: The index of the PM domain.
>> + *
>> + * As @dev may only be attached to a single PM domain, the backend PM domain
>> + * provider creates a virtual device to attach instead. If attachment succeeds,
>> + * the ->detach() callback in the struct dev_pm_domain are assigned by the
>> + * corresponding backend attach function, as to deal with detaching of the
>> + * created virtual device.
>> + *
>> + * This function should typically be invoked by a driver during the probe phase,
>> + * in case its device requires power management through multiple PM domains. The
>> + * driver may benefit from using the received device, to configure device-links
>> + * towards its original device. Depending on the use-case and if needed, the
>> + * links may be dynamically changed by the driver, which allows it to control
>> + * the power to the PM domains independently from each other.
>> + *
>> + * Callers must ensure proper synchronization of this function with power
>> + * management callbacks.
>> + *
>> + * Returns the virtual created device when successfully attached to its PM
>> + * domain, NULL in case @dev don't need a PM domain, else an ERR_PTR().
>> + * Note that, to detach the returned virtual device, the driver shall call
>> + * dev_pm_domain_detach() on it, typically during the remove phase.
>> + */
>> +struct device *dev_pm_domain_attach_by_id(struct device *dev,
>> + unsigned int index)
>> +{
>> + if (dev->pm_domain)
>> + return ERR_PTR(-EEXIST);
>> +
>> + return genpd_dev_pm_attach_by_id(dev, index);
>> +}
>> +EXPORT_SYMBOL_GPL(dev_pm_domain_attach_by_id);
>> +
>> /**
>> * dev_pm_domain_detach - Detach a device from its PM domain.
>> * @dev: Device to detach.
>> * @power_off: Used to indicate whether we should power off the device.
>> *
>> - * This functions will reverse the actions from dev_pm_domain_attach() and thus
>> - * try to detach the @dev from its PM domain. Typically it should be invoked
>> - * from subsystem level code during the remove phase.
>> + * This functions will reverse the actions from dev_pm_domain_attach() and
>> + * dev_pm_domain_attach_by_id(), thus it detaches @dev from its PM domain.
>> + * Typically it should be invoked during the remove phase, either from
>> + * subsystem level code or from drivers.
>> *
>> * Callers must ensure proper synchronization of this function with power
>> * management callbacks.
>> diff --git a/include/linux/pm_domain.h b/include/linux/pm_domain.h
>> index 82458e8e2e01..9206a4fef9ac 100644
>> --- a/include/linux/pm_domain.h
>> +++ b/include/linux/pm_domain.h
>> @@ -299,6 +299,8 @@ struct generic_pm_domain *of_genpd_remove_last(struct device_node *np)
>>
>> #ifdef CONFIG_PM
>> int dev_pm_domain_attach(struct device *dev, bool power_on);
>> +struct device *dev_pm_domain_attach_by_id(struct device *dev,
>> + unsigned int index);
>> void dev_pm_domain_detach(struct device *dev, bool power_off);
>> void dev_pm_domain_set(struct device *dev, struct dev_pm_domain *pd);
>> #else
>> @@ -306,6 +308,11 @@ static inline int dev_pm_domain_attach(struct device *dev, bool power_on)
>> {
>> return 0;
>> }
>> +static inline struct device *dev_pm_domain_attach_by_id(struct device *dev,
>> + unsigned int index)
>> +{
>> + return NULL;
>> +}
>> static inline void dev_pm_domain_detach(struct device *dev, bool power_off) {}
>> static inline void dev_pm_domain_set(struct device *dev,
>> struct dev_pm_domain *pd) {}
>>
>
> My only other comments on this series are ...
>
> 1. I think it would be nice to have an dev_pm_domain_attach_by_name() and
> that the DT binding has a 'power-domain-names' property.
I think it makes sense, but my plan was to do that as second step on
top. Are you okay with that as well?
> 2. I am wondering if there could be value in having a
> dev_pm_domain_attach_link_all() helper which would attach and link all
> PM domains at once.
Perhaps it can be useful, yes! However, maybe we can postpone that to
after this series. I want to keep the series as simple as possible,
then we can build upon it.
Kind regards
Uffe
^ permalink raw reply
* [PATCH v2 0/9] PM / Domains: Add support for multi PM domains per device
From: Ulf Hansson @ 2018-05-30 11:34 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAJZ5v0iOP-gcdXcaOjuWy6p+k+hSkHuapDuYYFeS+6gDrxev3w@mail.gmail.com>
On 30 May 2018 at 11:30, Rafael J. Wysocki <rafael@kernel.org> wrote:
> On Tue, May 29, 2018 at 12:04 PM, Ulf Hansson <ulf.hansson@linaro.org> wrote:
>> Changes in v2:
>> - Addressed comments from Geert around DT doc.
>> - Addressed comments from Jon around clarification of how to use this
>> and changes to returned error codes.
>> - Fixed build error in case CONFIG_PM was unset.
>>
>> There are devices that are partitioned across multiple PM domains. Currently
>> these can't be supported well by the available PM infrastructures we have in
>> the kernel. This series is an attempt to address this.
>>
>> The interesting parts happens from patch 5 an onwards, including a minor DT
>> update to the existing power-domain bindings, the 4 earlier are just trivial
>> clean-ups of some related code in genpd, which I happened to stumble over.
>>
>> Some additional background:
>>
>> One existing case where devices are partitioned across multiple PM domains, is
>> the Nvida Tegra 124/210 X-USB subsystem. A while ago Jon Hunter (Nvidia) sent a
>> series, trying to address these issues, however this is a new approach, while
>> it re-uses the same concepts from DT point of view.
>>
>> The Tegra 124/210 X-USB subsystem contains of a host controller and a device
>> controller. Each controller have its own independent PM domain, but are being
>> partitioned across another shared PM domain for the USB super-speed logic.
>>
>> Currently to make the drivers work, either the related PM domains needs to stay
>> powered on always or the PM domain topology needs to be in-correctly modelled
>> through sub-domains. In both cases PM domains may be powered on while they
>> don't need to be, so in the end this means - wasting power -.
>>
>> As stated above, this series intends to address these problem from a PM
>> infrastructure point of view. More details are available in each changelog.
>>
>> It should be noted that this series has been tested on HW, however only by using
>> a home-cooked test PM domain driver for genpd and together with a test driver.
>> This allowed me to play with PM domain (genpd), runtime PM and device links.
>>
>> Any further deployment for real use cases are greatly appreciated. I am happy to
>> to help, if needed!
>>
>> Kind regards
>> Ulf Hansson
>>
>>
>> Ulf Hansson (9):
>> PM / Domains: Drop extern declarations of functions in pm_domain.h
>> PM / Domains: Drop __pm_genpd_add_device()
>> PM / Domains: Drop genpd as in-param for pm_genpd_remove_device()
>> PM / Domains: Drop unused parameter in genpd_allocate_dev_data()
>> PM / Domains: dt: Allow power-domain property to be a list of
>> specifiers
>> PM / Domains: Don't attach devices in genpd with multi PM domains
>> PM / Domains: Split genpd_dev_pm_attach()
>> PM / Domains: Add support for multi PM domains per device to genpd
>> PM / Domains: Add dev_pm_domain_attach_by_id() to manage multi PM
>> domains
>>
>> .../bindings/power/power_domain.txt | 19 ++-
>> drivers/base/power/common.c | 39 ++++-
>> drivers/base/power/domain.c | 155 ++++++++++++++----
>> drivers/gpu/drm/amd/amdgpu/amdgpu_acp.c | 2 +-
>> include/linux/pm_domain.h | 79 ++++-----
>> 5 files changed, 216 insertions(+), 78 deletions(-)
>
> I can take patches [1-4/9] from this series for 4.18.
Thanks!
>
> I need an ACK from Rob on the bindings change.
Yes, of course!
>
> The rest of the series doesn't seem to be ready yet.
It's getting reviewed and tested, so let's give it some more time.
BTW, from an overall design point of view, you seems okay with it?
Kind regards
Uffe
^ permalink raw reply
* [PATCH v4 0/5] Reintroduce i.MX EPIT Timer
From: Clément Péron @ 2018-05-30 12:03 UTC (permalink / raw)
To: linux-arm-kernel
From: Cl?ment Peron <clement.peron@devialet.com>
As suggested in the commit message we have added the device tree support,
proper bindings and we moved the driver into the correct folder.
Moreover we made some changes like use of relaxed IO accesor,
implement sched_clock, delay_timer and reduce the clockevents min_delta.
Changes since v3:
- Clean Kconfig
- Rename imx6q-epit to imx31-epit
- Update doc and bindings
- Indent and fix
Changes since v2 (Thanks Fabio Estevam):
- Removed unused ckil clock
- Add out_iounmap
- Check and handle if clk_prepare_enable failed
- Fix comment typo
Changes since v1 (Thanks Vladimir Zapolskiy):
- Add OF dependency in Kconfig
- Sort header
- Use BIT macro
- Remove useless comments
- Fix incorrect indent
- Fix memory leak
- Add check and handle possible returned error
Cl?ment Peron (2):
ARM: imx: remove inexistant EPIT timer init
Documentation: DT: add i.MX EPIT timer binding
Colin Didier (3):
clk: imx6: add EPIT clock support
clocksource: add driver for i.MX EPIT timer
ARM: dts: imx6qdl: add missing compatible and clock properties for
EPIT
.../devicetree/bindings/timer/fsl,imxepit.txt | 24 ++
arch/arm/boot/dts/imx6qdl.dtsi | 10 +
arch/arm/mach-imx/common.h | 1 -
drivers/clk/imx/clk-imx6q.c | 2 +
drivers/clocksource/Kconfig | 11 +
drivers/clocksource/Makefile | 1 +
drivers/clocksource/timer-imx-epit.c | 281 ++++++++++++++++++
include/dt-bindings/clock/imx6qdl-clock.h | 4 +-
8 files changed, 332 insertions(+), 2 deletions(-)
create mode 100644 Documentation/devicetree/bindings/timer/fsl,imxepit.txt
create mode 100644 drivers/clocksource/timer-imx-epit.c
--
2.17.0
^ permalink raw reply
* [PATCH v4 1/5] ARM: imx: remove inexistant EPIT timer init
From: Clément Péron @ 2018-05-30 12:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180530120327.27681-1-peron.clem@gmail.com>
From: Cl?ment Peron <clement.peron@devialet.com>
i.MX EPIT timer has been removed but not the init function declaration.
Signed-off-by: Cl?ment Peron <clement.peron@devialet.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
arch/arm/mach-imx/common.h | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm/mach-imx/common.h b/arch/arm/mach-imx/common.h
index c8d68e918b2f..18aae76fa2da 100644
--- a/arch/arm/mach-imx/common.h
+++ b/arch/arm/mach-imx/common.h
@@ -38,7 +38,6 @@ void imx21_soc_init(void);
void imx27_soc_init(void);
void imx31_soc_init(void);
void imx35_soc_init(void);
-void epit_timer_init(void __iomem *base, int irq);
int mx21_clocks_init(unsigned long lref, unsigned long fref);
int mx27_clocks_init(unsigned long fref);
int mx31_clocks_init(unsigned long fref);
--
2.17.0
^ permalink raw reply related
* [PATCH v4 2/5] clk: imx6: add EPIT clock support
From: Clément Péron @ 2018-05-30 12:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180530120327.27681-1-peron.clem@gmail.com>
From: Colin Didier <colin.didier@devialet.com>
Add EPIT clock support to the i.MX6Q clocking infrastructure.
Signed-off-by: Colin Didier <colin.didier@devialet.com>
Signed-off-by: Cl?ment Peron <clement.peron@devialet.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
drivers/clk/imx/clk-imx6q.c | 2 ++
include/dt-bindings/clock/imx6qdl-clock.h | 4 +++-
2 files changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/clk/imx/clk-imx6q.c b/drivers/clk/imx/clk-imx6q.c
index 8d518ad5dc13..b9ea7037e193 100644
--- a/drivers/clk/imx/clk-imx6q.c
+++ b/drivers/clk/imx/clk-imx6q.c
@@ -753,6 +753,8 @@ static void __init imx6q_clocks_init(struct device_node *ccm_node)
else
clk[IMX6Q_CLK_ECSPI5] = imx_clk_gate2("ecspi5", "ecspi_root", base + 0x6c, 8);
clk[IMX6QDL_CLK_ENET] = imx_clk_gate2("enet", "ipg", base + 0x6c, 10);
+ clk[IMX6QDL_CLK_EPIT1] = imx_clk_gate2("epit1", "ipg", base + 0x6c, 12);
+ clk[IMX6QDL_CLK_EPIT2] = imx_clk_gate2("epit2", "ipg", base + 0x6c, 14);
clk[IMX6QDL_CLK_ESAI_EXTAL] = imx_clk_gate2_shared("esai_extal", "esai_podf", base + 0x6c, 16, &share_count_esai);
clk[IMX6QDL_CLK_ESAI_IPG] = imx_clk_gate2_shared("esai_ipg", "ahb", base + 0x6c, 16, &share_count_esai);
clk[IMX6QDL_CLK_ESAI_MEM] = imx_clk_gate2_shared("esai_mem", "ahb", base + 0x6c, 16, &share_count_esai);
diff --git a/include/dt-bindings/clock/imx6qdl-clock.h b/include/dt-bindings/clock/imx6qdl-clock.h
index da59fd9cdb5e..7ad171b8f3bf 100644
--- a/include/dt-bindings/clock/imx6qdl-clock.h
+++ b/include/dt-bindings/clock/imx6qdl-clock.h
@@ -271,6 +271,8 @@
#define IMX6QDL_CLK_PRE_AXI 258
#define IMX6QDL_CLK_MLB_SEL 259
#define IMX6QDL_CLK_MLB_PODF 260
-#define IMX6QDL_CLK_END 261
+#define IMX6QDL_CLK_EPIT1 261
+#define IMX6QDL_CLK_EPIT2 262
+#define IMX6QDL_CLK_END 263
#endif /* __DT_BINDINGS_CLOCK_IMX6QDL_H */
--
2.17.0
^ permalink raw reply related
* [PATCH v4 3/5] Documentation: DT: add i.MX EPIT timer binding
From: Clément Péron @ 2018-05-30 12:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180530120327.27681-1-peron.clem@gmail.com>
From: Cl?ment Peron <clement.peron@devialet.com>
Add devicetree binding document for NXP's i.MX SoC specific
EPIT timer driver.
Signed-off-by: Cl?ment Peron <clement.peron@devialet.com>
---
.../devicetree/bindings/timer/fsl,imxepit.txt | 24 +++++++++++++++++++
1 file changed, 24 insertions(+)
create mode 100644 Documentation/devicetree/bindings/timer/fsl,imxepit.txt
diff --git a/Documentation/devicetree/bindings/timer/fsl,imxepit.txt b/Documentation/devicetree/bindings/timer/fsl,imxepit.txt
new file mode 100644
index 000000000000..90112d58af10
--- /dev/null
+++ b/Documentation/devicetree/bindings/timer/fsl,imxepit.txt
@@ -0,0 +1,24 @@
+Binding for the i.MX EPIT timer
+
+This binding uses the common clock binding[1].
+
+[1] Documentation/devicetree/bindings/clock/clock-bindings.txt
+
+Required properties:
+- compatible: should be "fsl,imx31-epit"
+- reg: physical base address of the controller and length of memory mapped
+ region.
+- interrupts: Should contain EPIT controller interrupt
+- clocks: list of clock specifiers, must contain an entry for each required
+ entry in clock-names
+- clock-names : should include entries "ipg", "per"
+
+Example for i.MX6QDL:
+ epit1: epit at 20d0000 {
+ compatible = "fsl,imx6q-epit", "fsl,imx31-epit";
+ reg = <0x020d0000 0x4000>;
+ interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG_PER>,
+ <&clks IMX6QDL_CLK_EPIT1>;
+ clock-names = "ipg", "per";
+ };
--
2.17.0
^ permalink raw reply related
* [PATCH v4 4/5] clocksource: add driver for i.MX EPIT timer
From: Clément Péron @ 2018-05-30 12:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180530120327.27681-1-peron.clem@gmail.com>
From: Colin Didier <colin.didier@devialet.com>
Add driver for NXP's EPIT timer used in i.MX 6 family of SoC.
Signed-off-by: Colin Didier <colin.didier@devialet.com>
Signed-off-by: Cl?ment Peron <clement.peron@devialet.com>
---
drivers/clocksource/Kconfig | 11 ++
drivers/clocksource/Makefile | 1 +
drivers/clocksource/timer-imx-epit.c | 281 +++++++++++++++++++++++++++
3 files changed, 293 insertions(+)
create mode 100644 drivers/clocksource/timer-imx-epit.c
diff --git a/drivers/clocksource/Kconfig b/drivers/clocksource/Kconfig
index 8e8a09755d10..790478afd02c 100644
--- a/drivers/clocksource/Kconfig
+++ b/drivers/clocksource/Kconfig
@@ -576,6 +576,17 @@ config H8300_TPU
This enables the clocksource for the H8300 platform with the
H8S2678 cpu.
+config CLKSRC_IMX_EPIT
+ bool "Clocksource using i.MX EPIT"
+ depends on CLKDEV_LOOKUP && (ARCH_MXC || COMPILE_TEST)
+ select CLKSRC_MMIO
+ help
+ This enables EPIT support available on some i.MX platforms.
+ Normally you don't have a reason to do so as the EPIT has
+ the same features and uses the same clocks as the GPT.
+ Anyway, on some systems the GPT may be in use for other
+ purposes.
+
config CLKSRC_IMX_GPT
bool "Clocksource using i.MX GPT" if COMPILE_TEST
depends on ARM && CLKDEV_LOOKUP
diff --git a/drivers/clocksource/Makefile b/drivers/clocksource/Makefile
index 00caf37e52f9..d9426f69ec69 100644
--- a/drivers/clocksource/Makefile
+++ b/drivers/clocksource/Makefile
@@ -69,6 +69,7 @@ obj-$(CONFIG_INTEGRATOR_AP_TIMER) += timer-integrator-ap.o
obj-$(CONFIG_CLKSRC_VERSATILE) += versatile.o
obj-$(CONFIG_CLKSRC_MIPS_GIC) += mips-gic-timer.o
obj-$(CONFIG_CLKSRC_TANGO_XTAL) += tango_xtal.o
+obj-$(CONFIG_CLKSRC_IMX_EPIT) += timer-imx-epit.o
obj-$(CONFIG_CLKSRC_IMX_GPT) += timer-imx-gpt.o
obj-$(CONFIG_CLKSRC_IMX_TPM) += timer-imx-tpm.o
obj-$(CONFIG_ASM9260_TIMER) += asm9260_timer.o
diff --git a/drivers/clocksource/timer-imx-epit.c b/drivers/clocksource/timer-imx-epit.c
new file mode 100644
index 000000000000..7e92fcab10d3
--- /dev/null
+++ b/drivers/clocksource/timer-imx-epit.c
@@ -0,0 +1,281 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * i.MX EPIT Timer
+ *
+ * Copyright (C) 2010 Sascha Hauer <s.hauer@pengutronix.de>
+ * Copyright (C) 2018 Colin Didier <colin.didier@devialet.com>
+ * Copyright (C) 2018 Cl?ment P?ron <clement.peron@devialet.com>
+ */
+
+#include <linux/clk.h>
+#include <linux/clockchips.h>
+#include <linux/err.h>
+#include <linux/interrupt.h>
+#include <linux/of_address.h>
+#include <linux/of_irq.h>
+#include <linux/sched_clock.h>
+#include <linux/slab.h>
+
+#define EPITCR 0x00
+#define EPITSR 0x04
+#define EPITLR 0x08
+#define EPITCMPR 0x0c
+#define EPITCNR 0x10
+
+#define EPITCR_EN BIT(0)
+#define EPITCR_ENMOD BIT(1)
+#define EPITCR_OCIEN BIT(2)
+#define EPITCR_RLD BIT(3)
+#define EPITCR_PRESC(x) (((x) & 0xfff) << 4)
+#define EPITCR_SWR BIT(16)
+#define EPITCR_IOVW BIT(17)
+#define EPITCR_DBGEN BIT(18)
+#define EPITCR_WAITEN BIT(19)
+#define EPITCR_RES BIT(20)
+#define EPITCR_STOPEN BIT(21)
+#define EPITCR_OM_DISCON (0 << 22)
+#define EPITCR_OM_TOGGLE (1 << 22)
+#define EPITCR_OM_CLEAR (2 << 22)
+#define EPITCR_OM_SET (3 << 22)
+#define EPITCR_CLKSRC_OFF (0 << 24)
+#define EPITCR_CLKSRC_PERIPHERAL (1 << 24)
+#define EPITCR_CLKSRC_REF_HIGH (2 << 24)
+#define EPITCR_CLKSRC_REF_LOW (3 << 24)
+
+#define EPITSR_OCIF BIT(0)
+
+struct epit_timer {
+ void __iomem *base;
+ int irq;
+ struct clk *clk_per;
+ struct clock_event_device ced;
+ struct irqaction act;
+};
+
+static void __iomem *sched_clock_reg;
+
+static inline struct epit_timer *to_epit_timer(struct clock_event_device *ced)
+{
+ return container_of(ced, struct epit_timer, ced);
+}
+
+static inline void epit_irq_disable(struct epit_timer *epittm)
+{
+ u32 val;
+
+ val = readl_relaxed(epittm->base + EPITCR);
+ writel_relaxed(val & ~EPITCR_OCIEN, epittm->base + EPITCR);
+}
+
+static inline void epit_irq_enable(struct epit_timer *epittm)
+{
+ u32 val;
+
+ val = readl_relaxed(epittm->base + EPITCR);
+ writel_relaxed(val | EPITCR_OCIEN, epittm->base + EPITCR);
+}
+
+static void epit_irq_acknowledge(struct epit_timer *epittm)
+{
+ writel_relaxed(EPITSR_OCIF, epittm->base + EPITSR);
+}
+
+static u64 notrace epit_read_sched_clock(void)
+{
+ return ~readl_relaxed(sched_clock_reg);
+}
+
+static int epit_set_next_event(unsigned long cycles,
+ struct clock_event_device *ced)
+{
+ struct epit_timer *epittm = to_epit_timer(ced);
+ unsigned long tcmp;
+
+ tcmp = readl_relaxed(epittm->base + EPITCNR) - cycles;
+ writel_relaxed(tcmp, epittm->base + EPITCMPR);
+
+ return 0;
+}
+
+/* Left event sources disabled, no more interrupts appear */
+static int epit_shutdown(struct clock_event_device *ced)
+{
+ struct epit_timer *epittm = to_epit_timer(ced);
+ unsigned long flags;
+
+ /*
+ * The timer interrupt generation is disabled at least
+ * for enough time to call epit_set_next_event()
+ */
+ local_irq_save(flags);
+
+ /* Disable interrupt in EPIT module */
+ epit_irq_disable(epittm);
+
+ /* Clear pending interrupt */
+ epit_irq_acknowledge(epittm);
+
+ local_irq_restore(flags);
+
+ return 0;
+}
+
+static int epit_set_oneshot(struct clock_event_device *ced)
+{
+ struct epit_timer *epittm = to_epit_timer(ced);
+ unsigned long flags;
+
+ /*
+ * The timer interrupt generation is disabled at least
+ * for enough time to call epit_set_next_event()
+ */
+ local_irq_save(flags);
+
+ /* Disable interrupt in EPIT module */
+ epit_irq_disable(epittm);
+
+ /* Clear pending interrupt, only while switching mode */
+ if (!clockevent_state_oneshot(ced))
+ epit_irq_acknowledge(epittm);
+
+ /*
+ * Do not put overhead of interrupt enable/disable into
+ * epit_set_next_event(), the core has about 4 minutes
+ * to call epit_set_next_event() or shutdown clock after
+ * mode switching
+ */
+ epit_irq_enable(epittm);
+ local_irq_restore(flags);
+
+ return 0;
+}
+
+static irqreturn_t epit_timer_interrupt(int irq, void *dev_id)
+{
+ struct clock_event_device *ced = dev_id;
+ struct epit_timer *epittm = to_epit_timer(ced);
+
+ epit_irq_acknowledge(epittm);
+
+ ced->event_handler(ced);
+
+ return IRQ_HANDLED;
+}
+
+static int __init epit_clocksource_init(struct epit_timer *epittm)
+{
+ unsigned int c = clk_get_rate(epittm->clk_per);
+
+ sched_clock_reg = epittm->base + EPITCNR;
+ sched_clock_register(epit_read_sched_clock, 32, c);
+
+ return clocksource_mmio_init(epittm->base + EPITCNR, "epit", c, 200, 32,
+ clocksource_mmio_readl_down);
+}
+
+static int __init epit_clockevent_init(struct epit_timer *epittm)
+{
+ struct clock_event_device *ced = &epittm->ced;
+ struct irqaction *act = &epittm->act;
+
+ ced->name = "epit";
+ ced->features = CLOCK_EVT_FEAT_ONESHOT | CLOCK_EVT_FEAT_DYNIRQ;
+ ced->set_state_shutdown = epit_shutdown;
+ ced->tick_resume = epit_shutdown;
+ ced->set_state_oneshot = epit_set_oneshot;
+ ced->set_next_event = epit_set_next_event;
+ ced->rating = 200;
+ ced->cpumask = cpumask_of(0);
+ ced->irq = epittm->irq;
+ clockevents_config_and_register(ced, clk_get_rate(epittm->clk_per),
+ 0xff, 0xfffffffe);
+
+ act->name = "i.MX EPIT Timer Tick",
+ act->flags = IRQF_TIMER | IRQF_IRQPOLL;
+ act->handler = epit_timer_interrupt;
+ act->dev_id = ced;
+
+ /* Make irqs happen */
+ return setup_irq(epittm->irq, act);
+}
+
+static int __init epit_timer_init(struct device_node *np)
+{
+ struct epit_timer *epittm;
+ struct clk *clk_ipg;
+ int ret;
+
+ epittm = kzalloc(sizeof(*epittm), GFP_KERNEL);
+ if (!epittm)
+ return -ENOMEM;
+
+ epittm->base = of_iomap(np, 0);
+ if (!epittm->base) {
+ ret = -ENXIO;
+ goto out_kfree;
+ }
+
+ epittm->irq = irq_of_parse_and_map(np, 0);
+ if (!epittm->irq) {
+ ret = -EINVAL;
+ goto out_iounmap;
+ }
+
+ clk_ipg = of_clk_get_by_name(np, "ipg");
+ if (IS_ERR(clk_ipg)) {
+ pr_err("i.MX EPIT: unable to get clk_ipg\n");
+ ret = PTR_ERR(clk_ipg);
+ goto out_iounmap;
+ }
+
+ ret = clk_prepare_enable(clk_ipg);
+ if (ret) {
+ pr_err("i.MX EPIT: unable to prepare+enable clk_ipg\n");
+ goto out_iounmap;
+ }
+
+ epittm->clk_per = of_clk_get_by_name(np, "per");
+ if (IS_ERR(epittm->clk_per)) {
+ pr_err("i.MX EPIT: unable to get clk_per\n");
+ ret = PTR_ERR(epittm->clk_per);
+ goto out_clk_ipg_disable;
+ }
+
+ ret = clk_prepare_enable(epittm->clk_per);
+ if (ret) {
+ pr_err("i.MX EPIT: unable to prepare+enable clk_per\n");
+ goto out_clk_ipg_disable;
+ }
+
+ /* Initialise to a known state (all timers off, and timing reset) */
+ writel_relaxed(0x0, epittm->base + EPITCR);
+ writel_relaxed(0xffffffff, epittm->base + EPITLR);
+ writel_relaxed(EPITCR_EN | EPITCR_CLKSRC_REF_HIGH | EPITCR_WAITEN,
+ epittm->base + EPITCR);
+
+ ret = epit_clocksource_init(epittm);
+ if (ret) {
+ pr_err("i.MX EPIT: failed to init clocksource\n");
+ goto out_clk_per_disable;
+ }
+
+ ret = epit_clockevent_init(epittm);
+ if (ret) {
+ pr_err("i.MX EPIT: failed to init clockevent\n");
+ goto out_clk_per_disable;
+ }
+
+ return 0;
+
+out_clk_per_disable:
+ clk_disable_unprepare(epittm->clk_per);
+out_clk_ipg_disable:
+ clk_disable_unprepare(clk_ipg);
+out_iounmap:
+ iounmap(epittm->base);
+out_kfree:
+ kfree(epittm);
+
+ return ret;
+}
+TIMER_OF_DECLARE(epit_timer, "fsl,imx31-epit", epit_timer_init);
--
2.17.0
^ permalink raw reply related
* [PATCH v4 5/5] ARM: dts: imx6qdl: add missing compatible and clock properties for EPIT
From: Clément Péron @ 2018-05-30 12:03 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <20180530120327.27681-1-peron.clem@gmail.com>
From: Colin Didier <colin.didier@devialet.com>
Add missing compatible and clock properties for EPIT node.
Signed-off-by: Colin Didier <colin.didier@devialet.com>
Signed-off-by: Cl?ment Peron <clement.peron@devialet.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
---
arch/arm/boot/dts/imx6qdl.dtsi | 10 ++++++++++
1 file changed, 10 insertions(+)
diff --git a/arch/arm/boot/dts/imx6qdl.dtsi b/arch/arm/boot/dts/imx6qdl.dtsi
index c003e62bf290..0feec516847a 100644
--- a/arch/arm/boot/dts/imx6qdl.dtsi
+++ b/arch/arm/boot/dts/imx6qdl.dtsi
@@ -844,13 +844,23 @@
};
epit1: epit at 20d0000 { /* EPIT1 */
+ compatible = "fsl,imx6q-epit", "fsl,imx31-epit";
reg = <0x020d0000 0x4000>;
interrupts = <0 56 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG_PER>,
+ <&clks IMX6QDL_CLK_EPIT1>;
+ clock-names = "ipg", "per";
+ status = "disabled";
};
epit2: epit at 20d4000 { /* EPIT2 */
+ compatible = "fsl,imx6q-epit", "fsl,imx31-epit";
reg = <0x020d4000 0x4000>;
interrupts = <0 57 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&clks IMX6QDL_CLK_IPG_PER>,
+ <&clks IMX6QDL_CLK_EPIT2>;
+ clock-names = "ipg", "per";
+ status = "disabled";
};
src: src at 20d8000 {
--
2.17.0
^ permalink raw reply related
* [PATCH] ARM: debug: enable UART1 for socfpga Cyclone5
From: Clément Péron @ 2018-05-30 12:12 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CAJiuCccyY5B-cXB1fUBAm5JqY796jyE0KZqSSv23h3WAe4zqOA@mail.gmail.com>
Hi Dinh,
On Thu, 3 May 2018 at 16:49, Cl?ment P?ron <peron.clem@gmail.com> wrote:
> Hi Dinh,
> On Thu, 3 May 2018 at 16:32, Dinh Nguyen <dinguyen@kernel.org> wrote:
> > Do you have a Cyclone5/Arria5 board that is using UART1 for the debug
> port?
> > Dinh
> Yes I have a Cyclone5 board where the debug serial port used is UART1,
> Clement
Does it looks like good to you ?
Regards,
Clement
^ permalink raw reply
* [PATCH v2 00/10] Add TOSHIBA TC358764 DSI/LVDS bridge driver
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <CGME20180530121622eucas1p1015b65cd12a544b1ea72fe6bfd1a3ccc@eucas1p1.samsung.com>
Hi all,
this patchset is a next attempt to add the tc358764 driver.
The previous one can be found here:
https://lists.freedesktop.org/archives/dri-devel/2014-February/053705.html
Back then, TC358764 was added as a panel driver.
The bridge is supposed to be a DSI peripheral. Currently exynos_dsi accepts only panels
as its peripherals. Therefore, some logic in exynos_dsi had to be ammended. That is implemented
in first 4 patches.
Apart from the driver this patchset adds support for BOE HV070WSA-100 panel, which is used by
TC358764 and dts nodes to exynos5250.dtsi and exynos5250-arndale.dtsi.
Best regards,
Maciej Purski
---
Changes in v2:
- fix commits authorship
- don't call pm_runtime_put_sync() in exyons_dsi_disable(), if pm_runtime_get_sync()
has not been called
- squash dts commits
- merge some redundant regulators in tc358764 bindings and in DTS
- fix kbuild robot errors
Andrzej Hajda (6):
panel/hv070wsa-100: add DT bindings
drm/panel: add support for BOE HV070WSA-100 panel to simple-panel
dt-bindings: tc358754: add DT bindings
drm/bridge: tc358764: Add DSI to LVDS bridge driver
ARM: dts: exynos5250: add DSI node
ARM: dts: exynos5250-arndale: add DSI and panel nodes
Maciej Purski (4):
drm/exynos: rename "bridge_node" to "mic_bridge_node"
drm/exynos: move pm_runtime_get_sync() to exynos_dsi_init()
drm/exynos: move connector creation to attach callback
drm/exynos: add non-panel path to exynos_dsi_enable()
.../bindings/display/bridge/toshiba,tc358764.txt | 37 ++
.../bindings/display/panel/boe,hv070wsa-100.txt | 7 +
arch/arm/boot/dts/exynos5250-arndale.dts | 61 +++
arch/arm/boot/dts/exynos5250.dtsi | 21 +
drivers/gpu/drm/bridge/Kconfig | 9 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/tc358764.c | 547 +++++++++++++++++++++
drivers/gpu/drm/exynos/exynos_drm_dsi.c | 88 ++--
drivers/gpu/drm/panel/panel-simple.c | 25 +
9 files changed, 755 insertions(+), 41 deletions(-)
create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
create mode 100644 Documentation/devicetree/bindings/display/panel/boe,hv070wsa-100.txt
create mode 100644 drivers/gpu/drm/bridge/tc358764.c
--
2.7.4
^ permalink raw reply
* [PATCH v2 01/10] drm/exynos: rename "bridge_node" to "mic_bridge_node"
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
When adding support for peripheral out bridges, the "bridge" name
becomes imprecise as it refers to a different device than the
"out_bridge".
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
drivers/gpu/drm/exynos/exynos_drm_dsi.c | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index eae44fd..9599e6b 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -279,7 +279,7 @@ struct exynos_dsi {
struct list_head transfer_list;
const struct exynos_dsi_driver_data *driver_data;
- struct device_node *bridge_node;
+ struct device_node *mic_bridge_node;
};
#define host_to_dsi(host) container_of(host, struct exynos_dsi, dsi_host)
@@ -1631,7 +1631,7 @@ static int exynos_dsi_parse_dt(struct exynos_dsi *dsi)
if (ret < 0)
return ret;
- dsi->bridge_node = of_graph_get_remote_node(node, DSI_PORT_IN, 0);
+ dsi->mic_bridge_node = of_graph_get_remote_node(node, DSI_PORT_IN, 0);
return 0;
}
@@ -1642,7 +1642,7 @@ static int exynos_dsi_bind(struct device *dev, struct device *master,
struct drm_encoder *encoder = dev_get_drvdata(dev);
struct exynos_dsi *dsi = encoder_to_dsi(encoder);
struct drm_device *drm_dev = data;
- struct drm_bridge *bridge;
+ struct drm_bridge *mic_bridge;
int ret;
drm_encoder_init(drm_dev, encoder, &exynos_dsi_encoder_funcs,
@@ -1661,10 +1661,10 @@ static int exynos_dsi_bind(struct device *dev, struct device *master,
return ret;
}
- if (dsi->bridge_node) {
- bridge = of_drm_find_bridge(dsi->bridge_node);
- if (bridge)
- drm_bridge_attach(encoder, bridge, NULL);
+ if (dsi->mic_bridge_node) {
+ mic_bridge = of_drm_find_bridge(dsi->mic_bridge_node);
+ if (mic_bridge)
+ drm_bridge_attach(encoder, mic_bridge, NULL);
}
return mipi_dsi_host_register(&dsi->dsi_host);
@@ -1783,7 +1783,7 @@ static int exynos_dsi_remove(struct platform_device *pdev)
{
struct exynos_dsi *dsi = platform_get_drvdata(pdev);
- of_node_put(dsi->bridge_node);
+ of_node_put(dsi->mic_bridge_node);
pm_runtime_disable(&pdev->dev);
--
2.7.4
^ permalink raw reply related
* [PATCH v2 02/10] drm/exynos: move pm_runtime_get_sync() to exynos_dsi_init()
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
In order to allow bridge drivers to use DSI transfers in their
pre_enable callbacks, pm_runtime_get_sync() should be performed before
exynos_dsi_enable(). DSIM_STATE_ENABLED flag now should not guard
from calling dsi_host_transfer() before enabling.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
drivers/gpu/drm/exynos/exynos_drm_dsi.c | 11 +++++------
1 file changed, 5 insertions(+), 6 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index 9599e6b..85eb2262 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -1312,6 +1312,7 @@ static int exynos_dsi_init(struct exynos_dsi *dsi)
{
const struct exynos_dsi_driver_data *driver_data = dsi->driver_data;
+ pm_runtime_get_sync(dsi->dev);
exynos_dsi_reset(dsi);
exynos_dsi_enable_irq(dsi);
@@ -1388,7 +1389,6 @@ static void exynos_dsi_enable(struct drm_encoder *encoder)
ret = drm_panel_prepare(dsi->panel);
if (ret < 0) {
dsi->state &= ~DSIM_STATE_ENABLED;
- pm_runtime_put_sync(dsi->dev);
return;
}
@@ -1400,7 +1400,6 @@ static void exynos_dsi_enable(struct drm_encoder *encoder)
dsi->state &= ~DSIM_STATE_ENABLED;
exynos_dsi_set_display_enable(dsi, false);
drm_panel_unprepare(dsi->panel);
- pm_runtime_put_sync(dsi->dev);
return;
}
@@ -1422,7 +1421,10 @@ static void exynos_dsi_disable(struct drm_encoder *encoder)
dsi->state &= ~DSIM_STATE_ENABLED;
- pm_runtime_put_sync(dsi->dev);
+ if (dsi->state & DSIM_STATE_INITIALIZED) {
+ pm_runtime_put_sync(dsi->dev);
+ dsi->state &= ~DSIM_STATE_INITIALIZED;
+ }
}
static enum drm_connector_status
@@ -1566,9 +1568,6 @@ static ssize_t exynos_dsi_host_transfer(struct mipi_dsi_host *host,
struct exynos_dsi_transfer xfer;
int ret;
- if (!(dsi->state & DSIM_STATE_ENABLED))
- return -EINVAL;
-
if (!(dsi->state & DSIM_STATE_INITIALIZED)) {
ret = exynos_dsi_init(dsi);
if (ret)
--
2.7.4
^ permalink raw reply related
* [PATCH v2 03/10] drm/exynos: move connector creation to attach callback
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
The current implementation assumes that the only possible peripheral
device for DSIM is a panel. Using an output bridge should also be
possible.
If an output bridge in available, don't create a new connector.
Instead add bridge to DSIM encdoer in dsi_host_attach().
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
drivers/gpu/drm/exynos/exynos_drm_dsi.c | 35 +++++++++++++++++++++------------
1 file changed, 22 insertions(+), 13 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index 85eb2262..7b50bad 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -1501,7 +1501,28 @@ static int exynos_dsi_host_attach(struct mipi_dsi_host *host,
struct mipi_dsi_device *device)
{
struct exynos_dsi *dsi = host_to_dsi(host);
- struct drm_device *drm = dsi->connector.dev;
+ struct drm_encoder *encoder = &dsi->encoder;
+ struct drm_device *drm = encoder->dev;
+ struct drm_bridge *out_bridge;
+
+ out_bridge = of_drm_find_bridge(device->dev.of_node);
+ if (out_bridge) {
+ drm_bridge_attach(encoder, out_bridge, NULL);
+ } else {
+ int ret = exynos_dsi_create_connector(encoder);
+
+ if (ret) {
+ DRM_ERROR("failed to create connector ret = %d\n", ret);
+ drm_encoder_cleanup(encoder);
+ return ret;
+ }
+
+ dsi->panel = of_drm_find_panel(device->dev.of_node);
+ if (dsi->panel) {
+ drm_panel_attach(dsi->panel, &dsi->connector);
+ dsi->connector.status = connector_status_connected;
+ }
+ }
/*
* This is a temporary solution and should be made by more generic way.
@@ -1520,11 +1541,6 @@ static int exynos_dsi_host_attach(struct mipi_dsi_host *host,
dsi->lanes = device->lanes;
dsi->format = device->format;
dsi->mode_flags = device->mode_flags;
- dsi->panel = of_drm_find_panel(device->dev.of_node);
- if (dsi->panel) {
- drm_panel_attach(dsi->panel, &dsi->connector);
- dsi->connector.status = connector_status_connected;
- }
exynos_drm_crtc_get_by_type(drm, EXYNOS_DISPLAY_TYPE_LCD)->i80_mode =
!(dsi->mode_flags & MIPI_DSI_MODE_VIDEO);
@@ -1653,13 +1669,6 @@ static int exynos_dsi_bind(struct device *dev, struct device *master,
if (ret < 0)
return ret;
- ret = exynos_dsi_create_connector(encoder);
- if (ret) {
- DRM_ERROR("failed to create connector ret = %d\n", ret);
- drm_encoder_cleanup(encoder);
- return ret;
- }
-
if (dsi->mic_bridge_node) {
mic_bridge = of_drm_find_bridge(dsi->mic_bridge_node);
if (mic_bridge)
--
2.7.4
^ permalink raw reply related
* [PATCH v2 04/10] drm/exynos: add non-panel path to exynos_dsi_enable()
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
As DSIM can now have a bridge connected as a peripheral, it should be
possible to successfully enable exynos_dsi, when there is no panel
provided.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
drivers/gpu/drm/exynos/exynos_drm_dsi.c | 26 ++++++++++++--------------
1 file changed, 12 insertions(+), 14 deletions(-)
diff --git a/drivers/gpu/drm/exynos/exynos_drm_dsi.c b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
index 7b50bad..7f6a0b1 100644
--- a/drivers/gpu/drm/exynos/exynos_drm_dsi.c
+++ b/drivers/gpu/drm/exynos/exynos_drm_dsi.c
@@ -1382,27 +1382,25 @@ static void exynos_dsi_enable(struct drm_encoder *encoder)
if (dsi->state & DSIM_STATE_ENABLED)
return;
- pm_runtime_get_sync(dsi->dev);
-
- dsi->state |= DSIM_STATE_ENABLED;
-
- ret = drm_panel_prepare(dsi->panel);
- if (ret < 0) {
- dsi->state &= ~DSIM_STATE_ENABLED;
- return;
+ if (dsi->panel) {
+ ret = drm_panel_prepare(dsi->panel);
+ if (ret < 0)
+ return;
}
exynos_dsi_set_display_mode(dsi);
exynos_dsi_set_display_enable(dsi, true);
- ret = drm_panel_enable(dsi->panel);
- if (ret < 0) {
- dsi->state &= ~DSIM_STATE_ENABLED;
- exynos_dsi_set_display_enable(dsi, false);
- drm_panel_unprepare(dsi->panel);
- return;
+ if (dsi->panel) {
+ ret = drm_panel_enable(dsi->panel);
+ if (ret < 0) {
+ exynos_dsi_set_display_enable(dsi, false);
+ drm_panel_unprepare(dsi->panel);
+ return;
+ }
}
+ dsi->state |= DSIM_STATE_ENABLED;
dsi->state |= DSIM_STATE_VIDOUT_AVAILABLE;
}
--
2.7.4
^ permalink raw reply related
* [PATCH v2 05/10] panel/hv070wsa-100: add DT bindings
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
From: Andrzej Hajda <a.hajda@samsung.com>
The patch adds bindings to BOE HV070-WSA WSVGA panel.
Bindings are compatible with simple panel bindings.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
.../devicetree/bindings/display/panel/boe,hv070wsa-100.txt | 7 +++++++
1 file changed, 7 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/boe,hv070wsa-100.txt
diff --git a/Documentation/devicetree/bindings/display/panel/boe,hv070wsa-100.txt b/Documentation/devicetree/bindings/display/panel/boe,hv070wsa-100.txt
new file mode 100644
index 0000000..bfc20ac
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/boe,hv070wsa-100.txt
@@ -0,0 +1,7 @@
+BOE HV070WSA-100 7.01" WSVGA TFT LCD panel
+
+Required properties:
+- compatible: should be "boe,hv070wsa-100"
+
+This binding is compatible with the simple-panel binding, which is specified
+in simple-panel.txt in this directory.
--
2.7.4
^ permalink raw reply related
* [PATCH v2 06/10] drm/panel: add support for BOE HV070WSA-100 panel to simple-panel
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
From: Andrzej Hajda <a.hajda@samsung.com>
The patch adds support for BOE HV070WSA-100 WSVGA 7.01 inch panel
in panel-simple driver. The panel is used in Exynos5250-arndale boards.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
drivers/gpu/drm/panel/panel-simple.c | 25 +++++++++++++++++++++++++
1 file changed, 25 insertions(+)
diff --git a/drivers/gpu/drm/panel/panel-simple.c b/drivers/gpu/drm/panel/panel-simple.c
index cbf1ab4..d5da58d 100644
--- a/drivers/gpu/drm/panel/panel-simple.c
+++ b/drivers/gpu/drm/panel/panel-simple.c
@@ -745,6 +745,28 @@ static const struct panel_desc avic_tm070ddh03 = {
},
};
+static const struct drm_display_mode boe_hv070wsa_mode = {
+ .clock = 40800,
+ .hdisplay = 1024,
+ .hsync_start = 1024 + 90,
+ .hsync_end = 1024 + 90 + 90,
+ .htotal = 1024 + 90 + 90 + 90,
+ .vdisplay = 600,
+ .vsync_start = 600 + 3,
+ .vsync_end = 600 + 3 + 4,
+ .vtotal = 600 + 3 + 4 + 3,
+ .vrefresh = 60,
+};
+
+static const struct panel_desc boe_hv070wsa = {
+ .modes = &boe_hv070wsa_mode,
+ .num_modes = 1,
+ .size = {
+ .width = 154,
+ .height = 90,
+ },
+};
+
static const struct drm_display_mode boe_nv101wxmn51_modes[] = {
{
.clock = 71900,
@@ -2113,6 +2135,9 @@ static const struct of_device_id platform_of_match[] = {
.compatible = "avic,tm070ddh03",
.data = &avic_tm070ddh03,
}, {
+ .compatible = "boe,hv070wsa-100",
+ .data = &boe_hv070wsa
+ }, {
.compatible = "boe,nv101wxmn51",
.data = &boe_nv101wxmn51,
}, {
--
2.7.4
^ permalink raw reply related
* [PATCH v2 07/10] dt-bindings: tc358754: add DT bindings
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
From: Andrzej Hajda <a.hajda@samsung.com>
The patch adds bindings to Toshiba DSI/LVDS bridge TC358764.
Bindings describe power supplies, reset gpio and video interfaces.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
.../bindings/display/bridge/toshiba,tc358764.txt | 37 ++++++++++++++++++++++
1 file changed, 37 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
diff --git a/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
new file mode 100644
index 0000000..6eda14f
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/bridge/toshiba,tc358764.txt
@@ -0,0 +1,37 @@
+TC358764 MIPI-DSI to LVDS panel bridge
+
+Required properties:
+ - compatible: "toshiba,tc358764"
+ - reg: the virtual channel number of a DSI peripheral
+ - vddc-supply: core voltage supply, 1.2V
+ - vddio-supply: I/O voltage supply, 1.8V or 3.3V
+ - vddlvds-supply: LVDS1/2 voltage supply, 3.3V
+ - reset-gpios: a GPIO spec for the reset pin
+
+The device node can contain zero to two 'port' child nodes, each with one
+child 'endpoint' node, according to the bindings defined in [1].
+The following are properties specific to those nodes.
+
+port:
+ - reg: (required) can be 0 for DSI port or 1 for LVDS port;
+
+[1]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ bridge at 0 {
+ reg = <0>;
+ compatible = "toshiba,tc358764";
+ vddc-supply = <&vcc_1v2_reg>;
+ vddio-supply = <&vcc_1v8_reg>;
+ vddlvds-supply = <&vcc_3v3_reg>;
+ reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 1 {
+ reg = <1>;
+ lvds_ep: endpoint {
+ remote-endpoint = <&panel_ep>;
+ };
+ };
+ };
--
2.7.4
^ permalink raw reply related
* [PATCH v2 08/10] drm/bridge: tc358764: Add DSI to LVDS bridge driver
From: Maciej Purski @ 2018-05-30 12:15 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
From: Andrzej Hajda <a.hajda@samsung.com>
Add a drm_bridge driver for the Toshiba TC358764 DSI to LVDS bridge.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
drivers/gpu/drm/bridge/Kconfig | 9 +
drivers/gpu/drm/bridge/Makefile | 1 +
drivers/gpu/drm/bridge/tc358764.c | 547 ++++++++++++++++++++++++++++++++++++++
3 files changed, 557 insertions(+)
create mode 100644 drivers/gpu/drm/bridge/tc358764.c
diff --git a/drivers/gpu/drm/bridge/Kconfig b/drivers/gpu/drm/bridge/Kconfig
index fa2c799..9bd3eb8 100644
--- a/drivers/gpu/drm/bridge/Kconfig
+++ b/drivers/gpu/drm/bridge/Kconfig
@@ -110,6 +110,15 @@ config DRM_THINE_THC63LVD1024
---help---
Thine THC63LVD1024 LVDS/parallel converter driver.
+config DRM_TOSHIBA_TC358764
+ tristate "TC358764 DSI/LVDS bridge"
+ depends on DRM && DRM_PANEL
+ depends on OF
+ select DRM_MIPI_DSI
+ select VIDEOMODE_HELPERS
+ help
+ Toshiba TC358764 DSI/LVDS bridge driver
+
config DRM_TOSHIBA_TC358767
tristate "Toshiba TC358767 eDP bridge"
depends on OF
diff --git a/drivers/gpu/drm/bridge/Makefile b/drivers/gpu/drm/bridge/Makefile
index 35f88d4..bf7c0ce 100644
--- a/drivers/gpu/drm/bridge/Makefile
+++ b/drivers/gpu/drm/bridge/Makefile
@@ -10,6 +10,7 @@ obj-$(CONFIG_DRM_SIL_SII8620) += sil-sii8620.o
obj-$(CONFIG_DRM_SII902X) += sii902x.o
obj-$(CONFIG_DRM_SII9234) += sii9234.o
obj-$(CONFIG_DRM_THINE_THC63LVD1024) += thc63lvd1024.o
+obj-$(CONFIG_DRM_TOSHIBA_TC358764) += tc358764.o
obj-$(CONFIG_DRM_TOSHIBA_TC358767) += tc358767.o
obj-$(CONFIG_DRM_ANALOGIX_DP) += analogix/
obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511/
diff --git a/drivers/gpu/drm/bridge/tc358764.c b/drivers/gpu/drm/bridge/tc358764.c
new file mode 100644
index 0000000..3109eba
--- /dev/null
+++ b/drivers/gpu/drm/bridge/tc358764.c
@@ -0,0 +1,547 @@
+/*
+ * Copyright (C) 2018 Samsung Electronics Co., Ltd
+ *
+ * Authors:
+ * Andrzej Hajda <a.hajda@samsung.com>
+ * Maciej Purski <m.purski@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program.
+ *
+ */
+
+#include <drm/drm_atomic_helper.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_mipi_dsi.h>
+#include <drm/drm_panel.h>
+
+#include <drm/drm_crtc.h>
+#include <drm/drm_crtc_helper.h>
+
+#include <linux/gpio/consumer.h>
+#include <linux/of_graph.h>
+#include <linux/regulator/consumer.h>
+
+#include <video/mipi_display.h>
+#include <video/of_videomode.h>
+#include <video/videomode.h>
+
+#define FLD_MASK(start, end) (((1 << ((start) - (end) + 1)) - 1) << (end))
+#define FLD_VAL(val, start, end) (((val) << (end)) & FLD_MASK(start, end))
+
+/* PPI layer registers */
+#define PPI_STARTPPI 0x0104 /* START control bit */
+#define PPI_LPTXTIMECNT 0x0114 /* LPTX timing signal */
+#define PPI_LANEENABLE 0x0134 /* Enables each lane */
+#define PPI_TX_RX_TA 0x013C /* BTA timing parameters */
+#define PPI_D0S_CLRSIPOCOUNT 0x0164 /* Assertion timer for Lane 0 */
+#define PPI_D1S_CLRSIPOCOUNT 0x0168 /* Assertion timer for Lane 1 */
+#define PPI_D2S_CLRSIPOCOUNT 0x016C /* Assertion timer for Lane 2 */
+#define PPI_D3S_CLRSIPOCOUNT 0x0170 /* Assertion timer for Lane 3 */
+#define PPI_START_FUNCTION 1
+
+/* DSI layer registers */
+#define DSI_STARTDSI 0x0204 /* START control bit of DSI-TX */
+#define DSI_LANEENABLE 0x0210 /* Enables each lane */
+#define DSI_RX_START 1
+
+/* Video path registers */
+#define VP_CTRL 0x0450 /* Video Path Control */
+#define VP_CTRL_MSF(v) FLD_VAL(v, 0, 0) /* Magic square in RGB666 */
+#define VP_CTRL_VTGEN(v) FLD_VAL(v, 4, 4) /* Use chip clock for timing */
+#define VP_CTRL_EVTMODE(v) FLD_VAL(v, 5, 5) /* Event mode */
+#define VP_CTRL_RGB888(v) FLD_VAL(v, 8, 8) /* RGB888 mode */
+#define VP_CTRL_VSDELAY(v) FLD_VAL(v, 31, 20) /* VSYNC delay */
+#define VP_CTRL_HSPOL BIT(17) /* Polarity of HSYNC signal */
+#define VP_CTRL_DEPOL BIT(18) /* Polarity of DE signal */
+#define VP_CTRL_VSPOL BIT(19) /* Polarity of VSYNC signal */
+#define VP_HTIM1 0x0454 /* Horizontal Timing Control 1 */
+#define VP_HTIM1_HBP(v) FLD_VAL(v, 24, 16)
+#define VP_HTIM1_HSYNC(v) FLD_VAL(v, 8, 0)
+#define VP_HTIM2 0x0458 /* Horizontal Timing Control 2 */
+#define VP_HTIM2_HFP(v) FLD_VAL(v, 24, 16)
+#define VP_HTIM2_HACT(v) FLD_VAL(v, 10, 0)
+#define VP_VTIM1 0x045C /* Vertical Timing Control 1 */
+#define VP_VTIM1_VBP(v) FLD_VAL(v, 23, 16)
+#define VP_VTIM1_VSYNC(v) FLD_VAL(v, 7, 0)
+#define VP_VTIM2 0x0460 /* Vertical Timing Control 2 */
+#define VP_VTIM2_VFP(v) FLD_VAL(v, 23, 16)
+#define VP_VTIM2_VACT(v) FLD_VAL(v, 10, 0)
+#define VP_VFUEN 0x0464 /* Video Frame Timing Update Enable */
+
+/* LVDS registers */
+#define LV_MX0003 0x0480 /* Mux input bit 0 to 3 */
+#define LV_MX0407 0x0484 /* Mux input bit 4 to 7 */
+#define LV_MX0811 0x0488 /* Mux input bit 8 to 11 */
+#define LV_MX1215 0x048C /* Mux input bit 12 to 15 */
+#define LV_MX1619 0x0490 /* Mux input bit 16 to 19 */
+#define LV_MX2023 0x0494 /* Mux input bit 20 to 23 */
+#define LV_MX2427 0x0498 /* Mux input bit 24 to 27 */
+#define LV_MX(b0, b1, b2, b3) (FLD_VAL(b0, 4, 0) | FLD_VAL(b1, 12, 8) | \
+ FLD_VAL(b2, 20, 16) | FLD_VAL(b3, 28, 24))
+
+/* Input bit numbers used in mux registers */
+enum {
+ LVI_R0,
+ LVI_R1,
+ LVI_R2,
+ LVI_R3,
+ LVI_R4,
+ LVI_R5,
+ LVI_R6,
+ LVI_R7,
+ LVI_G0,
+ LVI_G1,
+ LVI_G2,
+ LVI_G3,
+ LVI_G4,
+ LVI_G5,
+ LVI_G6,
+ LVI_G7,
+ LVI_B0,
+ LVI_B1,
+ LVI_B2,
+ LVI_B3,
+ LVI_B4,
+ LVI_B5,
+ LVI_B6,
+ LVI_B7,
+ LVI_HS,
+ LVI_VS,
+ LVI_DE,
+ LVI_L0
+};
+
+#define LV_CFG 0x049C /* LVDS Configuration */
+#define LV_PHY0 0x04A0 /* LVDS PHY 0 */
+#define LV_PHY0_RST(v) FLD_VAL(v, 22, 22) /* PHY reset */
+#define LV_PHY0_IS(v) FLD_VAL(v, 15, 14)
+#define LV_PHY0_ND(v) FLD_VAL(v, 4, 0) /* Frequency range select */
+#define LV_PHY0_PRBS_ON(v) FLD_VAL(v, 20, 16) /* Clock/Data Flag pins */
+
+/* System registers */
+#define SYS_RST 0x0504 /* System Reset */
+#define SYS_ID 0x0580 /* System ID */
+
+#define SYS_RST_I2CS BIT(0) /* Reset I2C-Slave controller */
+#define SYS_RST_I2CM BIT(1) /* Reset I2C-Master controller */
+#define SYS_RST_LCD BIT(2) /* Reset LCD controller */
+#define SYS_RST_BM BIT(3) /* Reset Bus Management controller */
+#define SYS_RST_DSIRX BIT(4) /* Reset DSI-RX and App controller */
+#define SYS_RST_REG BIT(5) /* Reset Register module */
+
+#define LPX_PERIOD 2
+#define TTA_SURE 3
+#define TTA_GET 0x20000
+
+/* Lane enable PPI and DSI register bits */
+#define LANEENABLE_CLEN BIT(0)
+#define LANEENABLE_L0EN BIT(1)
+#define LANEENABLE_L1EN BIT(2)
+#define LANEENABLE_L2EN BIT(3)
+#define LANEENABLE_L3EN BIT(4)
+
+/* LVCFG fields */
+#define LV_CFG_LVEN BIT(0)
+#define LV_CFG_LVDLINK BIT(1)
+#define LV_CFG_CLKPOL1 BIT(2)
+#define LV_CFG_CLKPOL2 BIT(3)
+
+static const char * const tc358764_supplies[] = {
+ "vddc", "vddio", "vddmipi", "vddlvds133", "vddlvds112"
+};
+
+struct tc358764 {
+ struct device *dev;
+ struct drm_bridge bridge;
+ struct drm_connector connector;
+ struct regulator_bulk_data supplies[ARRAY_SIZE(tc358764_supplies)];
+ struct gpio_desc *gpio_reset;
+
+ struct drm_panel *panel;
+};
+
+static int tc358764_read(struct tc358764 *ctx, u16 addr, u32 *val)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ const struct mipi_dsi_host_ops *ops = dsi->host->ops;
+ struct mipi_dsi_msg msg = {
+ .type = MIPI_DSI_GENERIC_READ_REQUEST_2_PARAM,
+ .channel = dsi->channel,
+ .flags = MIPI_DSI_MSG_USE_LPM,
+ .tx_buf = &addr,
+ .tx_len = 2,
+ .rx_buf = val,
+ .rx_len = 4
+ };
+ ssize_t ret;
+
+ if (!ops || !ops->transfer)
+ return -EINVAL;
+
+ cpu_to_le16s(&addr);
+
+ ret = ops->transfer(dsi->host, &msg);
+ if (ret >= 0)
+ le32_to_cpus(val);
+
+ dev_dbg(ctx->dev, "read: %d, addr: %d\n", addr, *val);
+
+ return ret;
+}
+
+static int tc358764_write(struct tc358764 *ctx, u16 addr, u32 val)
+{
+ struct mipi_dsi_device *dsi = to_mipi_dsi_device(ctx->dev);
+ const struct mipi_dsi_host_ops *ops = dsi->host->ops;
+ u8 data[6];
+ int ret;
+ struct mipi_dsi_msg msg = {
+ .type = MIPI_DSI_GENERIC_LONG_WRITE,
+ .channel = dsi->channel,
+ .flags = MIPI_DSI_MSG_USE_LPM | MIPI_DSI_MSG_REQ_ACK,
+ .tx_buf = data,
+ .tx_len = 6
+ };
+
+ if (!ops || !ops->transfer)
+ return -EINVAL;
+
+ data[0] = addr;
+ data[1] = addr >> 8;
+ data[2] = val;
+ data[3] = val >> 8;
+ data[4] = val >> 16;
+ data[5] = val >> 24;
+
+ ret = ops->transfer(dsi->host, &msg);
+
+ return ret;
+}
+
+static inline struct tc358764 *bridge_to_tc358764(struct drm_bridge *bridge)
+{
+ return container_of(bridge, struct tc358764, bridge);
+}
+
+static inline
+struct tc358764 *connector_to_tc358764(struct drm_connector *connector)
+{
+ return container_of(connector, struct tc358764, connector);
+}
+
+static int tc358764_init(struct tc358764 *ctx)
+{
+ u32 v = 0;
+
+ tc358764_read(ctx, SYS_ID, &v);
+ dev_info(ctx->dev, "ID: %#x\n", v);
+
+ /* configure PPI counters */
+ tc358764_write(ctx, PPI_TX_RX_TA, TTA_GET | TTA_SURE);
+ tc358764_write(ctx, PPI_LPTXTIMECNT, LPX_PERIOD);
+ tc358764_write(ctx, PPI_D0S_CLRSIPOCOUNT, 5);
+ tc358764_write(ctx, PPI_D1S_CLRSIPOCOUNT, 5);
+ tc358764_write(ctx, PPI_D2S_CLRSIPOCOUNT, 5);
+ tc358764_write(ctx, PPI_D3S_CLRSIPOCOUNT, 5);
+
+ /* enable four data lanes and clock lane */
+ tc358764_write(ctx, PPI_LANEENABLE, LANEENABLE_L3EN | LANEENABLE_L2EN |
+ LANEENABLE_L1EN | LANEENABLE_L0EN | LANEENABLE_CLEN);
+ tc358764_write(ctx, DSI_LANEENABLE, LANEENABLE_L3EN | LANEENABLE_L2EN |
+ LANEENABLE_L1EN | LANEENABLE_L0EN | LANEENABLE_CLEN);
+
+ /* start */
+ tc358764_write(ctx, PPI_STARTPPI, PPI_START_FUNCTION);
+ tc358764_write(ctx, DSI_STARTDSI, DSI_RX_START);
+
+ /* configure video path */
+ tc358764_write(ctx, VP_CTRL, VP_CTRL_VSDELAY(15) | VP_CTRL_RGB888(1) |
+ VP_CTRL_EVTMODE(1) | VP_CTRL_HSPOL | VP_CTRL_VSPOL);
+
+ /* reset PHY */
+ tc358764_write(ctx, LV_PHY0, LV_PHY0_RST(1) |
+ LV_PHY0_PRBS_ON(4) | LV_PHY0_IS(2) | LV_PHY0_ND(6));
+ tc358764_write(ctx, LV_PHY0, LV_PHY0_PRBS_ON(4) | LV_PHY0_IS(2) |
+ LV_PHY0_ND(6));
+
+ /* reset bridge */
+ tc358764_write(ctx, SYS_RST, SYS_RST_LCD);
+
+ /* set bit order */
+ tc358764_write(ctx, LV_MX0003, LV_MX(LVI_R0, LVI_R1, LVI_R2, LVI_R3));
+ tc358764_write(ctx, LV_MX0407, LV_MX(LVI_R4, LVI_R7, LVI_R5, LVI_G0));
+ tc358764_write(ctx, LV_MX0811, LV_MX(LVI_G1, LVI_G2, LVI_G6, LVI_G7));
+ tc358764_write(ctx, LV_MX1215, LV_MX(LVI_G3, LVI_G4, LVI_G5, LVI_B0));
+ tc358764_write(ctx, LV_MX1619, LV_MX(LVI_B6, LVI_B7, LVI_B1, LVI_B2));
+ tc358764_write(ctx, LV_MX2023, LV_MX(LVI_B3, LVI_B4, LVI_B5, LVI_L0));
+ tc358764_write(ctx, LV_MX2427, LV_MX(LVI_HS, LVI_VS, LVI_DE, LVI_R6));
+ tc358764_write(ctx, LV_CFG, LV_CFG_CLKPOL2 | LV_CFG_CLKPOL1 |
+ LV_CFG_LVEN);
+
+ return 0;
+}
+
+static void tc358764_reset(struct tc358764 *ctx)
+{
+ msleep(20);
+ gpiod_set_value(ctx->gpio_reset, 0);
+ msleep(20);
+ gpiod_set_value(ctx->gpio_reset, 1);
+ msleep(40);
+}
+
+static void tc358764_poweroff(struct tc358764 *ctx)
+{
+ int ret;
+
+ tc358764_reset(ctx);
+
+ drm_panel_disable(ctx->panel);
+ msleep(40);
+
+ ret = regulator_bulk_disable(ARRAY_SIZE(ctx->supplies), ctx->supplies);
+ if (ret < 0)
+ dev_err(ctx->dev, "error disabling regulators (%d)\n", ret);
+}
+
+static int tc358764_get_modes(struct drm_connector *connector)
+{
+ struct tc358764 *ctx = connector_to_tc358764(connector);
+
+ if (ctx->panel && ctx->panel->funcs && ctx->panel->funcs->get_modes)
+ return ctx->panel->funcs->get_modes(ctx->panel);
+
+ return 0;
+}
+
+static const
+struct drm_connector_helper_funcs tc358764_connector_helper_funcs = {
+ .get_modes = tc358764_get_modes,
+};
+
+static const struct drm_connector_funcs tc358764_connector_funcs = {
+ .fill_modes = drm_helper_probe_single_connector_modes,
+ .destroy = drm_connector_cleanup,
+ .reset = drm_atomic_helper_connector_reset,
+ .atomic_duplicate_state = drm_atomic_helper_connector_duplicate_state,
+ .atomic_destroy_state = drm_atomic_helper_connector_destroy_state,
+};
+
+static void tc358764_disable(struct drm_bridge *bridge)
+{
+ struct tc358764 *ctx = bridge_to_tc358764(bridge);
+
+ tc358764_poweroff(ctx);
+}
+
+static void tc358764_pre_enable(struct drm_bridge *bridge)
+{
+ struct tc358764 *ctx = bridge_to_tc358764(bridge);
+ int ret = regulator_bulk_enable(ARRAY_SIZE(ctx->supplies),
+ ctx->supplies);
+ if (ret < 0)
+ dev_err(ctx->dev, "error enabling regulators (%d)\n", ret);
+
+ tc358764_reset(ctx);
+ tc358764_init(ctx);
+}
+
+static void tc358764_enable(struct drm_bridge *bridge)
+{
+ struct tc358764 *ctx = bridge_to_tc358764(bridge);
+ int ret;
+
+ drm_panel_prepare(ctx->panel);
+
+ ret = drm_panel_enable(ctx->panel);
+ if (ret < 0)
+ pr_err("panel enable failed\n");
+
+ msleep(40);
+}
+
+static int tc358764_attach(struct drm_bridge *bridge)
+{
+ struct tc358764 *ctx = bridge_to_tc358764(bridge);
+ struct drm_device *drm = bridge->dev;
+ int ret;
+
+ if (!bridge->encoder) {
+ DRM_ERROR("Encoder not found\n");
+ return -ENODEV;
+ }
+
+ ctx->connector.polled = DRM_CONNECTOR_POLL_HPD;
+ ret = drm_connector_init(drm, &ctx->connector,
+ &tc358764_connector_funcs,
+ DRM_MODE_CONNECTOR_LVDS);
+ if (ret) {
+ DRM_ERROR("Failed to initialize connector\n");
+ return ret;
+ }
+
+ drm_connector_helper_add(&ctx->connector,
+ &tc358764_connector_helper_funcs);
+
+ drm_mode_connector_attach_encoder(&ctx->connector, bridge->encoder);
+
+ if (ctx->panel)
+ drm_panel_attach(ctx->panel, &ctx->connector);
+
+ drm_atomic_helper_connector_reset(&ctx->connector);
+ drm_connector_register(&ctx->connector);
+
+ return 0;
+}
+
+static const struct drm_bridge_funcs tc358764_bridge_funcs = {
+ .disable = tc358764_disable,
+ .enable = tc358764_enable,
+ .pre_enable = tc358764_pre_enable,
+ .attach = tc358764_attach,
+};
+
+static struct device_node *tc358764_of_find_panel_node(struct device *dev)
+{
+ struct device_node *np, *ep;
+
+ ep = of_graph_get_endpoint_by_regs(dev->of_node, 1, 0);
+ if (!ep) {
+ pr_err("faile to get endpoint\n");
+ return NULL;
+ }
+
+ np = of_graph_get_remote_port_parent(ep);
+
+ return np;
+}
+
+static int tc358764_parse_dt(struct tc358764 *ctx)
+{
+ struct device *dev = ctx->dev;
+ struct device_node *np = dev->of_node;
+ struct device_node *lvds;
+
+ ctx->gpio_reset = devm_gpiod_get_from_of_node(dev, np, "reset", 0,
+ GPIOD_OUT_LOW,
+ "tc358764-reset");
+ if (IS_ERR(ctx->gpio_reset)) {
+ dev_err(dev, "no reset GPIO pin provided\n");
+ return PTR_ERR(ctx->gpio_reset);
+ }
+
+ lvds = tc358764_of_find_panel_node(ctx->dev);
+ if (!lvds) {
+ dev_err(dev, "cannot find panel node\n");
+ return -EINVAL;
+ }
+
+ ctx->panel = of_drm_find_panel(lvds);
+ if (!ctx->panel) {
+ dev_err(dev, "panel not registered\n");
+ return -EPROBE_DEFER;
+ }
+
+ return 0;
+}
+
+static int tc358764_configure_regulators(struct tc358764 *ctx)
+{
+ int i, ret;
+
+ for (i = 0; i < ARRAY_SIZE(ctx->supplies); ++i)
+ ctx->supplies[i].supply = tc358764_supplies[i];
+
+ ret = devm_regulator_bulk_get(ctx->dev, ARRAY_SIZE(ctx->supplies),
+ ctx->supplies);
+ if (ret < 0)
+ dev_err(ctx->dev, "failed to get regulators: %d\n", ret);
+
+ return ret;
+}
+
+static int tc358764_probe(struct mipi_dsi_device *dsi)
+{
+ struct device *dev = &dsi->dev;
+ struct tc358764 *ctx;
+ int ret;
+
+ ctx = devm_kzalloc(dev, sizeof(struct tc358764), GFP_KERNEL);
+ if (!ctx)
+ return -ENOMEM;
+
+ mipi_dsi_set_drvdata(dsi, ctx);
+
+ ctx->dev = dev;
+
+ dsi->lanes = 4;
+ dsi->format = MIPI_DSI_FMT_RGB888;
+ dsi->mode_flags = MIPI_DSI_MODE_VIDEO | MIPI_DSI_MODE_VIDEO_BURST
+ | MIPI_DSI_MODE_VIDEO_AUTO_VERT;
+
+ ret = tc358764_parse_dt(ctx);
+ if (ret < 0)
+ return ret;
+
+ ret = tc358764_configure_regulators(ctx);
+ if (ret < 0)
+ return ret;
+
+ ctx->bridge.funcs = &tc358764_bridge_funcs;
+ ctx->bridge.of_node = dev->of_node;
+
+ drm_bridge_add(&ctx->bridge);
+
+ ret = mipi_dsi_attach(dsi);
+ if (ret < 0) {
+ drm_bridge_remove(&ctx->bridge);
+ dev_err(dev, "failed to attach dsi\n");
+ }
+
+ return ret;
+}
+
+static int tc358764_remove(struct mipi_dsi_device *dsi)
+{
+ struct tc358764 *ctx = mipi_dsi_get_drvdata(dsi);
+
+ tc358764_poweroff(ctx);
+
+ mipi_dsi_detach(dsi);
+ drm_bridge_remove(&ctx->bridge);
+
+ return 0;
+}
+
+static const struct of_device_id tc358764_of_match[] = {
+ { .compatible = "toshiba,tc358764" },
+ { }
+};
+MODULE_DEVICE_TABLE(of, tc358764_of_match);
+
+static struct mipi_dsi_driver tc358764_driver = {
+ .probe = tc358764_probe,
+ .remove = tc358764_remove,
+ .driver = {
+ .name = "tc358764",
+ .owner = THIS_MODULE,
+ .of_match_table = tc358764_of_match,
+ },
+};
+module_mipi_dsi_driver(tc358764_driver);
+
+MODULE_AUTHOR("Andrzej Hajda <a.hajda@samsung.com>");
+MODULE_AUTHOR("Maciej Purski <m.purski@samsung.com>");
+MODULE_DESCRIPTION("MIPI-DSI based Driver for TC358764 DSI/LVDS Bridge");
+MODULE_LICENSE("GPL v2");
--
2.7.4
^ permalink raw reply related
* [PATCH v2 09/10] ARM: dts: exynos5250: add DSI node
From: Maciej Purski @ 2018-05-30 12:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
From: Andrzej Hajda <a.hajda@samsung.com>
The patch adds common part of DSI node for Exynos5250 platforms
and a required mipi-phy node.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
arch/arm/boot/dts/exynos5250.dtsi | 21 +++++++++++++++++++++
1 file changed, 21 insertions(+)
diff --git a/arch/arm/boot/dts/exynos5250.dtsi b/arch/arm/boot/dts/exynos5250.dtsi
index 2daf505..9965eca 100644
--- a/arch/arm/boot/dts/exynos5250.dtsi
+++ b/arch/arm/boot/dts/exynos5250.dtsi
@@ -733,6 +733,27 @@
#phy-cells = <0>;
};
+ mipi_phy: video-phy at 10040710 {
+ compatible = "samsung,s5pv210-mipi-video-phy";
+ reg = <0x10040710 0x100>;
+ #phy-cells = <1>;
+ syscon = <&pmu_system_controller>;
+ };
+
+ dsi_0: dsi at 14500000 {
+ compatible = "samsung,exynos4210-mipi-dsi";
+ reg = <0x14500000 0x10000>;
+ interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;
+ samsung,power-domain = <&pd_disp1>;
+ phys = <&mipi_phy 3>;
+ phy-names = "dsim";
+ clocks = <&clock CLK_DSIM0>, <&clock CLK_SCLK_MIPI1>;
+ clock-names = "bus_clk", "sclk_mipi";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
adc: adc at 12d10000 {
compatible = "samsung,exynos-adc-v1";
reg = <0x12D10000 0x100>;
--
2.7.4
^ permalink raw reply related
* [PATCH v2 10/10] ARM: dts: exynos5250-arndale: add DSI and panel nodes
From: Maciej Purski @ 2018-05-30 12:16 UTC (permalink / raw)
To: linux-arm-kernel
In-Reply-To: <1527682561-1386-1-git-send-email-m.purski@samsung.com>
From: Andrzej Hajda <a.hajda@samsung.com>
The patch adds bridge and panel nodes.
It adds also DSI properties specific for arndale board and
regulators required by the bridge.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Maciej Purski <m.purski@samsung.com>
---
arch/arm/boot/dts/exynos5250-arndale.dts | 61 ++++++++++++++++++++++++++++++++
1 file changed, 61 insertions(+)
diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 7a8a5c5..816d89d 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -71,6 +71,17 @@
};
};
+ panel: panel {
+ compatible = "boe,hv070wsa-100";
+ power-supply = <&vcc_3v3_reg>;
+ enable-gpios = <&gpd1 3 GPIO_ACTIVE_HIGH>;
+ port {
+ panel_ep: endpoint {
+ remote-endpoint = <&bridge_out_ep>;
+ };
+ };
+ };
+
regulators {
compatible = "simple-bus";
#address-cells = <1>;
@@ -97,6 +108,30 @@
reg = <2>;
regulator-name = "hdmi-en";
};
+
+ vcc_1v2_reg: regulator at 3 {
+ compatible = "regulator-fixed";
+ reg = <3>;
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ vcc_1v8_reg: regulator at 4 {
+ compatible = "regulator-fixed";
+ reg = <4>;
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ vcc_3v3_reg: regulator at 5 {
+ compatible = "regulator-fixed";
+ reg = <5>;
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
};
fixed-rate-clocks {
@@ -119,6 +154,32 @@
cpu0-supply = <&buck2_reg>;
};
+&dsi_0 {
+ vddcore-supply = <&ldo8_reg>;
+ vddio-supply = <&ldo10_reg>;
+ samsung,pll-clock-frequency = <24000000>;
+ samsung,burst-clock-frequency = <320000000>;
+ samsung,esc-clock-frequency = <10000000>;
+ status = "okay";
+
+ bridge at 0 {
+ reg = <0>;
+ compatible = "toshiba,tc358764";
+ vddc-supply = <&vcc_1v2_reg>;
+ vddio-supply = <&vcc_1v8_reg>;
+ vddlvds-supply = <&vcc_3v3_reg>;
+ reset-gpios = <&gpd1 6 GPIO_ACTIVE_LOW>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ port at 1 {
+ reg = <1>;
+ bridge_out_ep: endpoint {
+ remote-endpoint = <&panel_ep>;
+ };
+ };
+ };
+};
+
&dp {
status = "okay";
samsung,color-space = <0>;
--
2.7.4
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox