* [PATCH v4 10/14] drm/mxsfb: Update mxsfb to support LCD reset
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
The eLCDIF controller has control pin for the external LCD reset pin.
Add support for it and assert this pin in enable and de-assert it in
disable.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 14 ++++++++++----
drivers/gpu/drm/mxsfb/mxsfb_regs.h | 2 ++
2 files changed, 12 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index 1be29f5..a4ba368 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -224,9 +224,12 @@ static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb)
clk_prepare_enable(mxsfb->clk_disp_axi);
clk_prepare_enable(mxsfb->clk);
- if (mxsfb->devdata->ipversion >= 4)
+ if (mxsfb->devdata->ipversion >= 4) {
writel(CTRL2_OUTSTANDING_REQS(REQ_16),
mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
+ /* Assert LCD Reset bit */
+ writel(CTRL2_LCD_RESET, mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
+ }
/* If it was disabled, re-enable the mode again */
writel(CTRL_DOTCLK_MODE, mxsfb->base + LCDC_CTRL + REG_SET);
@@ -244,11 +247,14 @@ static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
{
u32 reg;
- if (mxsfb->devdata->ipversion >= 4)
+ writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_CLR);
+
+ if (mxsfb->devdata->ipversion >= 4) {
writel(CTRL2_OUTSTANDING_REQS(0x7),
mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
-
- writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_CLR);
+ /* De-assert LCD Reset bit */
+ writel(CTRL2_LCD_RESET, mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
+ }
/*
* Even if we disable the controller here, it will still continue
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
index dc4daa0..0f63ba1 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
@@ -108,6 +108,8 @@
#define CTRL2_LINE_PATTERN_BGR 5
#define CTRL2_LINE_PATTERN_CLR 7
+#define CTRL2_LCD_RESET BIT(0)
+
#define TRANSFER_COUNT_SET_VCOUNT(x) REG_PUT((x), 31, 16)
#define TRANSFER_COUNT_GET_VCOUNT(x) REG_GET((x), 31, 16)
#define TRANSFER_COUNT_SET_HCOUNT(x) REG_PUT((x), 15, 0)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 06/14] drm/mxsfb: Update mxsfb with additional pixel formats
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Since version 4 of eLCDIF, there are some registers that can do
transformations on the input data, like re-arranging the pixel
components. By doing that, we can support more pixel formats.
This patch adds support for X/ABGR and RGBX/A. Although, the local alpha
is not supported by eLCDIF, the alpha pixel formats were added to the
supported pixel formats but it will be ignored. This was necessary since
there are systems (like Android) that requires such pixel formats.
Also, add support for the following pixel formats:
16 bpp: RG16 ,BG16, XR15, XB15, AR15, AB15
Set the bus format based on input from the user and panel
capabilities.
Save the bus format in crtc->mode.private_flags, so the bridge can
use it.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Signed-off-by: Mirela Rabulea <mirela.rabulea@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 147 ++++++++++++++++++++++++++++++-------
drivers/gpu/drm/mxsfb/mxsfb_drv.c | 30 ++++++--
drivers/gpu/drm/mxsfb/mxsfb_drv.h | 3 +-
drivers/gpu/drm/mxsfb/mxsfb_regs.h | 15 ++++
4 files changed, 163 insertions(+), 32 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index 5e44f57..1be29f5 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -43,14 +43,17 @@ static u32 set_hsync_pulse_width(struct mxsfb_drm_private *mxsfb, u32 val)
}
/* Setup the MXSFB registers for decoding the pixels out of the framebuffer */
-static int mxsfb_set_pixel_fmt(struct mxsfb_drm_private *mxsfb)
+static int mxsfb_set_pixel_fmt(struct mxsfb_drm_private *mxsfb, bool update)
{
struct drm_crtc *crtc = &mxsfb->pipe.crtc;
struct drm_device *drm = crtc->dev;
const u32 format = crtc->primary->state->fb->format->format;
- u32 ctrl, ctrl1;
+ u32 ctrl = 0, ctrl1 = 0;
+ bool bgr_format = true;
+ struct drm_format_name_buf format_name_buf;
- ctrl = CTRL_BYPASS_COUNT | CTRL_MASTER;
+ if (!update)
+ ctrl = CTRL_BYPASS_COUNT | CTRL_MASTER;
/*
* WARNING: The bus width, CTRL_SET_BUS_WIDTH(), is configured to
@@ -59,64 +62,158 @@ static int mxsfb_set_pixel_fmt(struct mxsfb_drm_private *mxsfb)
* to arbitrary value. This limitation should not pose an issue.
*/
- /* CTRL1 contains IRQ config and status bits, preserve those. */
- ctrl1 = readl(mxsfb->base + LCDC_CTRL1);
- ctrl1 &= CTRL1_CUR_FRAME_DONE_IRQ_EN | CTRL1_CUR_FRAME_DONE_IRQ;
+ if (!update) {
+ /* CTRL1 contains IRQ config and status bits, preserve those. */
+ ctrl1 = readl(mxsfb->base + LCDC_CTRL1);
+ ctrl1 &= CTRL1_CUR_FRAME_DONE_IRQ_EN | CTRL1_CUR_FRAME_DONE_IRQ;
+ }
+
+ DRM_DEV_DEBUG_DRIVER(drm->dev, "Setting up %s mode\n",
+ drm_get_format_name(format, &format_name_buf));
+
+ /* Do some clean-up that we might have from a previous mode */
+ ctrl &= ~CTRL_SHIFT_DIR(1);
+ ctrl &= ~CTRL_SHIFT_NUM(0x3f);
+ if (mxsfb->devdata->ipversion >= 4)
+ writel(CTRL2_ODD_LINE_PATTERN(CTRL2_LINE_PATTERN_CLR) |
+ CTRL2_EVEN_LINE_PATTERN(CTRL2_LINE_PATTERN_CLR),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
switch (format) {
- case DRM_FORMAT_RGB565:
- dev_dbg(drm->dev, "Setting up RGB565 mode\n");
+ case DRM_FORMAT_BGR565: /* BG16 */
+ if (mxsfb->devdata->ipversion < 4)
+ goto err;
+ writel(CTRL2_ODD_LINE_PATTERN(CTRL2_LINE_PATTERN_BGR) |
+ CTRL2_EVEN_LINE_PATTERN(CTRL2_LINE_PATTERN_BGR),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
+ /* Fall through */
+ case DRM_FORMAT_RGB565: /* RG16 */
+ ctrl |= CTRL_SET_WORD_LENGTH(0);
+ ctrl &= ~CTRL_DF16;
+ ctrl1 |= CTRL1_SET_BYTE_PACKAGING(0xf);
+ break;
+ case DRM_FORMAT_XBGR1555: /* XB15 */
+ case DRM_FORMAT_ABGR1555: /* AB15 */
+ if (mxsfb->devdata->ipversion < 4)
+ goto err;
+ writel(CTRL2_ODD_LINE_PATTERN(CTRL2_LINE_PATTERN_BGR) |
+ CTRL2_EVEN_LINE_PATTERN(CTRL2_LINE_PATTERN_BGR),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
+ /* Fall through */
+ case DRM_FORMAT_XRGB1555: /* XR15 */
+ case DRM_FORMAT_ARGB1555: /* AR15 */
ctrl |= CTRL_SET_WORD_LENGTH(0);
+ ctrl |= CTRL_DF16;
ctrl1 |= CTRL1_SET_BYTE_PACKAGING(0xf);
break;
- case DRM_FORMAT_XRGB8888:
- dev_dbg(drm->dev, "Setting up XRGB8888 mode\n");
+ case DRM_FORMAT_RGBX8888: /* RX24 */
+ case DRM_FORMAT_RGBA8888: /* RA24 */
+ /* RGBX - > 0RGB */
+ ctrl |= CTRL_SHIFT_DIR(1);
+ ctrl |= CTRL_SHIFT_NUM(8);
+ bgr_format = false;
+ /* Fall through */
+ case DRM_FORMAT_XBGR8888: /* XB24 */
+ case DRM_FORMAT_ABGR8888: /* AB24 */
+ if (bgr_format) {
+ if (mxsfb->devdata->ipversion < 4)
+ goto err;
+ writel(CTRL2_ODD_LINE_PATTERN(CTRL2_LINE_PATTERN_BGR) |
+ CTRL2_EVEN_LINE_PATTERN(CTRL2_LINE_PATTERN_BGR),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
+ }
+ /* Fall through */
+ case DRM_FORMAT_XRGB8888: /* XR24 */
+ case DRM_FORMAT_ARGB8888: /* AR24 */
ctrl |= CTRL_SET_WORD_LENGTH(3);
/* Do not use packed pixels = one pixel per word instead. */
ctrl1 |= CTRL1_SET_BYTE_PACKAGING(0x7);
break;
default:
- dev_err(drm->dev, "Unhandled pixel format %08x\n", format);
- return -EINVAL;
+ goto err;
}
- writel(ctrl1, mxsfb->base + LCDC_CTRL1);
- writel(ctrl, mxsfb->base + LCDC_CTRL);
+ if (update) {
+ writel(ctrl, mxsfb->base + LCDC_CTRL + REG_SET);
+ writel(ctrl1, mxsfb->base + LCDC_CTRL1 + REG_SET);
+ } else {
+ writel(ctrl, mxsfb->base + LCDC_CTRL);
+ writel(ctrl1, mxsfb->base + LCDC_CTRL1);
+ }
return 0;
+
+err:
+ DRM_DEV_ERROR(drm->dev, "Unhandled pixel format: %s\n",
+ drm_get_format_name(format, &format_name_buf));
+
+ return -EINVAL;
+}
+
+static u32 get_bus_format_from_bpp(u32 bpp)
+{
+ switch (bpp) {
+ case 16:
+ return MEDIA_BUS_FMT_RGB565_1X16;
+ case 18:
+ return MEDIA_BUS_FMT_RGB666_1X18;
+ case 24:
+ return MEDIA_BUS_FMT_RGB888_1X24;
+ default:
+ return MEDIA_BUS_FMT_RGB888_1X24;
+ }
}
static void mxsfb_set_bus_fmt(struct mxsfb_drm_private *mxsfb)
{
struct drm_crtc *crtc = &mxsfb->pipe.crtc;
+ unsigned int bits_per_pixel = crtc->primary->state->fb->format->depth;
struct drm_device *drm = crtc->dev;
u32 bus_format = MEDIA_BUS_FMT_RGB888_1X24;
- u32 reg;
-
- reg = readl(mxsfb->base + LCDC_CTRL);
+ int num_bus_formats = mxsfb->connector->display_info.num_bus_formats;
+ const u32 *bus_formats = mxsfb->connector->display_info.bus_formats;
+ u32 reg = 0;
+ int i = 0;
+
+ /* match the user requested bus_format to one supported by the panel */
+ if (num_bus_formats) {
+ u32 user_bus_format = get_bus_format_from_bpp(bits_per_pixel);
+
+ bus_format = bus_formats[0];
+ for (i = 0; i < num_bus_formats; i++) {
+ if (user_bus_format == bus_formats[i]) {
+ bus_format = user_bus_format;
+ break;
+ }
+ }
+ }
- if (mxsfb->connector->display_info.num_bus_formats)
- bus_format = mxsfb->connector->display_info.bus_formats[0];
+ /*
+ * CRTC will dictate the bus format via private_flags[16:1]
+ * and private_flags[0] will signal a bus format change
+ */
+ crtc->mode.private_flags &= ~0x1FFFF; /* clear bus format */
+ crtc->mode.private_flags |= (bus_format << 1); /* set bus format */
+ crtc->mode.private_flags |= 0x1; /* bus format change indication*/
DRM_DEV_DEBUG_DRIVER(drm->dev, "Using bus_format: 0x%08X\n",
bus_format);
- reg &= ~CTRL_BUS_WIDTH_MASK;
switch (bus_format) {
case MEDIA_BUS_FMT_RGB565_1X16:
- reg |= CTRL_SET_BUS_WIDTH(STMLCDIF_16BIT);
+ reg = CTRL_SET_BUS_WIDTH(STMLCDIF_16BIT);
break;
case MEDIA_BUS_FMT_RGB666_1X18:
- reg |= CTRL_SET_BUS_WIDTH(STMLCDIF_18BIT);
+ reg = CTRL_SET_BUS_WIDTH(STMLCDIF_18BIT);
break;
case MEDIA_BUS_FMT_RGB888_1X24:
- reg |= CTRL_SET_BUS_WIDTH(STMLCDIF_24BIT);
+ reg = CTRL_SET_BUS_WIDTH(STMLCDIF_24BIT);
break;
default:
dev_err(drm->dev, "Unknown media bus format %d\n", bus_format);
break;
}
- writel(reg, mxsfb->base + LCDC_CTRL);
+ writel(reg, mxsfb->base + LCDC_CTRL + REG_SET);
}
static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb)
@@ -238,7 +335,7 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
/* Clear the FIFOs */
writel(CTRL1_FIFO_CLEAR, mxsfb->base + LCDC_CTRL1 + REG_SET);
- err = mxsfb_set_pixel_fmt(mxsfb);
+ err = mxsfb_set_pixel_fmt(mxsfb, false);
if (err)
return;
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.c b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
index 497cf44..23027a9 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
@@ -43,6 +43,27 @@ enum mxsfb_devtype {
MXSFB_V4,
};
+/*
+ * When adding new formats, make sure to update the num_formats from
+ * mxsfb_devdata below.
+ */
+static const u32 mxsfb_formats[] = {
+ /* MXSFB_V3 */
+ DRM_FORMAT_XRGB8888,
+ DRM_FORMAT_ARGB8888,
+ DRM_FORMAT_RGB565,
+ /* MXSFB_V4 */
+ DRM_FORMAT_XBGR8888,
+ DRM_FORMAT_ABGR8888,
+ DRM_FORMAT_RGBX8888,
+ DRM_FORMAT_RGBA8888,
+ DRM_FORMAT_ARGB1555,
+ DRM_FORMAT_XRGB1555,
+ DRM_FORMAT_ABGR1555,
+ DRM_FORMAT_XBGR1555,
+ DRM_FORMAT_BGR565
+};
+
static const struct mxsfb_devdata mxsfb_devdata[] = {
[MXSFB_V3] = {
.transfer_count = LCDC_V3_TRANSFER_COUNT,
@@ -52,6 +73,7 @@ static const struct mxsfb_devdata mxsfb_devdata[] = {
.hs_wdth_mask = 0xff,
.hs_wdth_shift = 24,
.ipversion = 3,
+ .num_formats = 3,
},
[MXSFB_V4] = {
.transfer_count = LCDC_V4_TRANSFER_COUNT,
@@ -61,14 +83,10 @@ static const struct mxsfb_devdata mxsfb_devdata[] = {
.hs_wdth_mask = 0x3fff,
.hs_wdth_shift = 18,
.ipversion = 4,
+ .num_formats = ARRAY_SIZE(mxsfb_formats),
},
};
-static const uint32_t mxsfb_formats[] = {
- DRM_FORMAT_XRGB8888,
- DRM_FORMAT_RGB565
-};
-
static struct mxsfb_drm_private *
drm_pipe_to_mxsfb_drm_private(struct drm_simple_display_pipe *pipe)
{
@@ -244,7 +262,7 @@ static int mxsfb_load(struct drm_device *drm, unsigned long flags)
}
ret = drm_simple_display_pipe_init(drm, &mxsfb->pipe, &mxsfb_funcs,
- mxsfb_formats, ARRAY_SIZE(mxsfb_formats), NULL,
+ mxsfb_formats, mxsfb->devdata->num_formats, NULL,
mxsfb->connector);
if (ret < 0) {
dev_err(drm->dev, "Cannot setup simple display pipe\n");
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.h b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
index 0b65b51..8fb65d3 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
@@ -16,6 +16,7 @@ struct mxsfb_devdata {
unsigned int hs_wdth_mask;
unsigned int hs_wdth_shift;
unsigned int ipversion;
+ unsigned int num_formats;
};
struct mxsfb_drm_private {
@@ -42,6 +43,6 @@ void mxsfb_disable_axi_clk(struct mxsfb_drm_private *mxsfb);
void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb);
void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb);
void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
- struct drm_plane_state *state);
+ struct drm_plane_state *old_state);
#endif /* __MXSFB_DRV_H__ */
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
index 9fcb1db..dc4daa0 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
@@ -44,6 +44,11 @@
#define REG_PUT(x, h, l) (((x) << (l)) & GENMASK(h, l))
#define REG_GET(x, h, l) (((x) & GENMASK(h, l)) >> (l))
+#define SWIZZLE_LE 0 /* Little-Endian or No swap */
+#define SWIZZLE_BE 1 /* Big-Endian or swap all */
+#define SWIZZLE_HWD 2 /* Swap half-words */
+#define SWIZZLE_HWD_BYTE 3 /* Swap bytes within each half-word */
+
#define CTRL_SFTRST BIT(31)
#define CTRL_CLKGATE BIT(30)
#define CTRL_SHIFT_DIR(x) REG_PUT((x), 26, 26)
@@ -93,6 +98,16 @@
#define REQ_8 3
#define REQ_16 4
+#define CTRL2_ODD_LINE_PATTERN(x) REG_PUT((x), 18, 16)
+#define CTRL2_EVEN_LINE_PATTERN(x) REG_PUT((x), 14, 12)
+#define CTRL2_LINE_PATTERN_RGB 0
+#define CTRL2_LINE_PATTERN_RBG 1
+#define CTRL2_LINE_PATTERN_GBR 2
+#define CTRL2_LINE_PATTERN_GRB 3
+#define CTRL2_LINE_PATTERN_BRG 4
+#define CTRL2_LINE_PATTERN_BGR 5
+#define CTRL2_LINE_PATTERN_CLR 7
+
#define TRANSFER_COUNT_SET_VCOUNT(x) REG_PUT((x), 31, 16)
#define TRANSFER_COUNT_GET_VCOUNT(x) REG_GET((x), 31, 16)
#define TRANSFER_COUNT_SET_HCOUNT(x) REG_PUT((x), 15, 0)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 14/14] drm/mxsfb: Add support for live pixel format change
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
This IP requires full stop and re-start when changing display timings,
but we can change the pixel format while running.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 16 +++++++++++++++-
1 file changed, 15 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index 317575e..5607fc0 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -494,6 +494,7 @@ void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
struct drm_crtc *crtc = &pipe->crtc;
struct drm_plane_state *new_state = pipe->plane.state;
struct drm_framebuffer *fb = pipe->plane.state->fb;
+ struct drm_framebuffer *old_fb = state->fb;
struct drm_pending_vblank_event *event;
u32 fb_addr, src_off, src_w, stride, cpp = 0;
@@ -510,7 +511,7 @@ void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
}
spin_unlock_irq(&crtc->dev->event_lock);
- if (!fb)
+ if (!fb || !old_fb)
return;
fb_addr = mxsfb_get_fb_paddr(mxsfb);
@@ -533,4 +534,17 @@ void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
src_w = new_state->src_w >> 16;
mxsfb_set_fb_hcrop(mxsfb, src_w, stride);
}
+
+ if (old_fb->format->format != fb->format->format) {
+ struct drm_format_name_buf old_fmt_buf;
+ struct drm_format_name_buf new_fmt_buf;
+
+ DRM_DEV_DEBUG_DRIVER(crtc->dev->dev,
+ "Switching pixel format: %s -> %s\n",
+ drm_get_format_name(old_fb->format->format,
+ &old_fmt_buf),
+ drm_get_format_name(fb->format->format,
+ &new_fmt_buf));
+ mxsfb_set_pixel_fmt(mxsfb, true);
+ }
}
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 13/14] drm/mxsfb: Add support for horizontal stride
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Besides the eLCDIF block, there is another IP block, used in the past
for EPDC panels. Since the iMX.8mq doesn't have an EPDC connector, this
block is not documented, but we can use it to do additional operations
on the frame buffer.
In this case, we can use the pigeon registers from this IP block in
order to do horizontal crop on the frame buffer processed by the eLCDIF
block.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 79 ++++++++++++++++++++++++++++++++++++--
drivers/gpu/drm/mxsfb/mxsfb_drv.c | 1 +
drivers/gpu/drm/mxsfb/mxsfb_regs.h | 16 ++++++++
3 files changed, 92 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index a12f53d..317575e 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -15,6 +15,7 @@
#include <video/videomode.h>
+#include <drm/drm_atomic.h>
#include <drm/drm_atomic_helper.h>
#include <drm/drm_crtc.h>
#include <drm/drm_fb_cma_helper.h>
@@ -435,13 +436,66 @@ void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
clk_disable_unprepare(mxsfb->clk_axi);
}
+void mxsfb_set_fb_hcrop(struct mxsfb_drm_private *mxsfb, u32 src_w, u32 fb_w)
+{
+ u32 mask_cnt, htotal, hcount;
+ u32 vdctrl2, vdctrl3, vdctrl4, transfer_count;
+ u32 pigeon_12_0, pigeon_12_1, pigeon_12_2;
+
+ if (src_w == fb_w) {
+ writel(0x0, mxsfb->base + HW_EPDC_PIGEON_12_0);
+ writel(0x0, mxsfb->base + HW_EPDC_PIGEON_12_1);
+
+ return;
+ }
+
+ transfer_count = readl(mxsfb->base + LCDC_V4_TRANSFER_COUNT);
+ hcount = TRANSFER_COUNT_GET_HCOUNT(transfer_count);
+
+ transfer_count &= ~TRANSFER_COUNT_SET_HCOUNT(0xffff);
+ transfer_count |= TRANSFER_COUNT_SET_HCOUNT(fb_w);
+ writel(transfer_count, mxsfb->base + LCDC_V4_TRANSFER_COUNT);
+
+ vdctrl2 = readl(mxsfb->base + LCDC_VDCTRL2);
+ htotal = VDCTRL2_GET_HSYNC_PERIOD(vdctrl2);
+ htotal += fb_w - hcount;
+ vdctrl2 &= ~VDCTRL2_SET_HSYNC_PERIOD(0x3ffff);
+ vdctrl2 |= VDCTRL2_SET_HSYNC_PERIOD(htotal);
+ writel(vdctrl2, mxsfb->base + LCDC_VDCTRL2);
+
+ vdctrl4 = readl(mxsfb->base + LCDC_VDCTRL4);
+ vdctrl4 &= ~SET_DOTCLK_H_VALID_DATA_CNT(0x3ffff);
+ vdctrl4 |= SET_DOTCLK_H_VALID_DATA_CNT(fb_w);
+ writel(vdctrl4, mxsfb->base + LCDC_VDCTRL4);
+
+ /* configure related pigeon registers */
+ vdctrl3 = readl(mxsfb->base + LCDC_VDCTRL3);
+ mask_cnt = GET_HOR_WAIT_CNT(vdctrl3) - 5;
+
+ pigeon_12_0 = PIGEON_12_0_SET_STATE_MASK(0x24) |
+ PIGEON_12_0_SET_MASK_CNT(mask_cnt) |
+ PIGEON_12_0_SET_MASK_CNT_SEL(0x6) |
+ PIGEON_12_0_POL_ACTIVE_LOW |
+ PIGEON_12_0_EN;
+ writel(pigeon_12_0, mxsfb->base + HW_EPDC_PIGEON_12_0);
+
+ pigeon_12_1 = PIGEON_12_1_SET_CLR_CNT(src_w) |
+ PIGEON_12_1_SET_SET_CNT(0x0);
+ writel(pigeon_12_1, mxsfb->base + HW_EPDC_PIGEON_12_1);
+
+ pigeon_12_2 = 0x0;
+ writel(pigeon_12_2, mxsfb->base + HW_EPDC_PIGEON_12_2);
+}
+
void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
struct drm_plane_state *state)
{
struct drm_simple_display_pipe *pipe = &mxsfb->pipe;
struct drm_crtc *crtc = &pipe->crtc;
+ struct drm_plane_state *new_state = pipe->plane.state;
+ struct drm_framebuffer *fb = pipe->plane.state->fb;
struct drm_pending_vblank_event *event;
- dma_addr_t paddr;
+ u32 fb_addr, src_off, src_w, stride, cpp = 0;
spin_lock_irq(&crtc->dev->event_lock);
event = crtc->state->event;
@@ -456,10 +510,27 @@ void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
}
spin_unlock_irq(&crtc->dev->event_lock);
- paddr = mxsfb_get_fb_paddr(mxsfb);
- if (paddr) {
+ if (!fb)
+ return;
+
+ fb_addr = mxsfb_get_fb_paddr(mxsfb);
+ if (mxsfb->devdata->ipversion >= 4) {
+ cpp = fb->format->cpp[0];
+ src_off = (new_state->src_y >> 16) * fb->pitches[0] +
+ (new_state->src_x >> 16) * cpp;
+ fb_addr += fb->offsets[0] + src_off;
+ }
+
+ if (fb_addr) {
clk_prepare_enable(mxsfb->clk_axi);
- writel(paddr, mxsfb->base + mxsfb->devdata->next_buf);
+ writel(fb_addr, mxsfb->base + mxsfb->devdata->next_buf);
clk_disable_unprepare(mxsfb->clk_axi);
}
+
+ if (mxsfb->devdata->ipversion >= 4 &&
+ unlikely(drm_atomic_crtc_needs_modeset(new_state->crtc->state))) {
+ stride = DIV_ROUND_UP(fb->pitches[0], cpp);
+ src_w = new_state->src_w >> 16;
+ mxsfb_set_fb_hcrop(mxsfb, src_w, stride);
+ }
}
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.c b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
index 888b520..06d3bf0 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
@@ -133,6 +133,7 @@ static int mxsfb_atomic_helper_check(struct drm_device *dev,
if (old_bpp != new_bpp)
new_state->mode_changed = true;
}
+
return ret;
}
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
index 0f63ba1..df3279b 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
@@ -145,6 +145,22 @@
#define DEBUG0_HSYNC BIT(26)
#define DEBUG0_VSYNC BIT(25)
+/* pigeon registers for crop */
+#define HW_EPDC_PIGEON_12_0 0xb00
+#define HW_EPDC_PIGEON_12_1 0xb10
+#define HW_EPDC_PIGEON_12_2 0xb20
+
+#define PIGEON_12_0_SET_STATE_MASK(x) REG_PUT((x), 31, 24)
+#define PIGEON_12_0_SET_MASK_CNT(x) REG_PUT((x), 23, 12)
+#define PIGEON_12_0_SET_MASK_CNT_SEL(x) REG_PUT((x), 11, 8)
+#define PIGEON_12_0_SET_OFFSET(x) REG_PUT((x), 7, 4)
+#define PIGEON_12_0_SET_INC_SEL(x) REG_PUT((x), 3, 2)
+#define PIGEON_12_0_POL_ACTIVE_LOW BIT(1)
+#define PIGEON_12_0_EN BIT(0)
+
+#define PIGEON_12_1_SET_CLR_CNT(x) REG_PUT((x), 31, 16)
+#define PIGEON_12_1_SET_SET_CNT(x) REG_PUT((x), 15, 0)
+
#define MXSFB_MIN_XRES 120
#define MXSFB_MIN_YRES 120
#define MXSFB_MAX_XRES 0xffff
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 12/14] drm/mxsfb: Clear OUTSTANDING_REQS bits
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Bit 21 can alter the CTRL2_OUTSTANDING_REQS value right after the eLCDIF
is enabled, since it comes up with default value of 1 (this behaviour
has been seen on some imx8 platforms).
In order to fix this, clear CTRL2_OUTSTANDING_REQS bits before setting
its value.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 7 +++++++
1 file changed, 7 insertions(+)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index e727f5e..a12f53d 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -225,6 +225,13 @@ static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb)
clk_prepare_enable(mxsfb->clk);
if (mxsfb->devdata->ipversion >= 4) {
+ /*
+ * On some platforms, bit 21 is defaulted to 1, which may alter
+ * the below setting. So, to make sure we have the right setting
+ * clear all the bits for CTRL2_OUTSTANDING_REQS.
+ */
+ writel(CTRL2_OUTSTANDING_REQS(0x7),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
writel(CTRL2_OUTSTANDING_REQS(REQ_16),
mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
/* Assert LCD Reset bit */
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 11/14] drm/mxsfb: Improve the axi clock usage
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Currently, the enable of the axi clock return status is ignored, causing
issues when the enable fails then we try to disable it. Therefore, it is
better to check the return status and disable it only when enable
succeeded.
Also, remove the helper functions around clk_axi, since we can directly
use the clk API function for enable/disable the clock. Those functions
are already checking for NULL clk and returning 0 if that's the case.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Acked-by: Leonard Crestez <leonard.crestez@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 8 ++++----
drivers/gpu/drm/mxsfb/mxsfb_drv.c | 32 +++++++++++++-------------------
drivers/gpu/drm/mxsfb/mxsfb_drv.h | 3 ---
3 files changed, 17 insertions(+), 26 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index a4ba368..e727f5e 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -408,7 +408,7 @@ void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
{
dma_addr_t paddr;
- mxsfb_enable_axi_clk(mxsfb);
+ clk_prepare_enable(mxsfb->clk_axi);
writel(0, mxsfb->base + LCDC_CTRL);
mxsfb_crtc_mode_set_nofb(mxsfb);
@@ -425,7 +425,7 @@ void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb)
{
mxsfb_disable_controller(mxsfb);
- mxsfb_disable_axi_clk(mxsfb);
+ clk_disable_unprepare(mxsfb->clk_axi);
}
void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
@@ -451,8 +451,8 @@ void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
paddr = mxsfb_get_fb_paddr(mxsfb);
if (paddr) {
- mxsfb_enable_axi_clk(mxsfb);
+ clk_prepare_enable(mxsfb->clk_axi);
writel(paddr, mxsfb->base + mxsfb->devdata->next_buf);
- mxsfb_disable_axi_clk(mxsfb);
+ clk_disable_unprepare(mxsfb->clk_axi);
}
}
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.c b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
index d8686c7..888b520 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
@@ -94,18 +94,6 @@ drm_pipe_to_mxsfb_drm_private(struct drm_simple_display_pipe *pipe)
return container_of(pipe, struct mxsfb_drm_private, pipe);
}
-void mxsfb_enable_axi_clk(struct mxsfb_drm_private *mxsfb)
-{
- if (mxsfb->clk_axi)
- clk_prepare_enable(mxsfb->clk_axi);
-}
-
-void mxsfb_disable_axi_clk(struct mxsfb_drm_private *mxsfb)
-{
- if (mxsfb->clk_axi)
- clk_disable_unprepare(mxsfb->clk_axi);
-}
-
/**
* mxsfb_atomic_helper_check - validate state object
* @dev: DRM device
@@ -265,25 +253,31 @@ static void mxsfb_pipe_update(struct drm_simple_display_pipe *pipe,
static int mxsfb_pipe_enable_vblank(struct drm_simple_display_pipe *pipe)
{
struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
+ int ret = 0;
+
+ ret = clk_prepare_enable(mxsfb->clk_axi);
+ if (ret)
+ return ret;
/* Clear and enable VBLANK IRQ */
- mxsfb_enable_axi_clk(mxsfb);
writel(CTRL1_CUR_FRAME_DONE_IRQ, mxsfb->base + LCDC_CTRL1 + REG_CLR);
writel(CTRL1_CUR_FRAME_DONE_IRQ_EN, mxsfb->base + LCDC_CTRL1 + REG_SET);
- mxsfb_disable_axi_clk(mxsfb);
+ clk_disable_unprepare(mxsfb->clk_axi);
- return 0;
+ return ret;
}
static void mxsfb_pipe_disable_vblank(struct drm_simple_display_pipe *pipe)
{
struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
+ if (clk_prepare_enable(mxsfb->clk_axi))
+ return;
+
/* Disable and clear VBLANK IRQ */
- mxsfb_enable_axi_clk(mxsfb);
writel(CTRL1_CUR_FRAME_DONE_IRQ_EN, mxsfb->base + LCDC_CTRL1 + REG_CLR);
writel(CTRL1_CUR_FRAME_DONE_IRQ, mxsfb->base + LCDC_CTRL1 + REG_CLR);
- mxsfb_disable_axi_clk(mxsfb);
+ clk_disable_unprepare(mxsfb->clk_axi);
}
static struct drm_simple_display_pipe_funcs mxsfb_funcs = {
@@ -444,7 +438,7 @@ static irqreturn_t mxsfb_irq_handler(int irq, void *data)
struct mxsfb_drm_private *mxsfb = drm->dev_private;
u32 reg;
- mxsfb_enable_axi_clk(mxsfb);
+ clk_prepare_enable(mxsfb->clk_axi);
reg = readl(mxsfb->base + LCDC_CTRL1);
@@ -453,7 +447,7 @@ static irqreturn_t mxsfb_irq_handler(int irq, void *data)
writel(CTRL1_CUR_FRAME_DONE_IRQ, mxsfb->base + LCDC_CTRL1 + REG_CLR);
- mxsfb_disable_axi_clk(mxsfb);
+ clk_disable_unprepare(mxsfb->clk_axi);
return IRQ_HANDLED;
}
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.h b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
index a178173..54c0644 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
@@ -39,9 +39,6 @@ struct mxsfb_drm_private {
int mxsfb_setup_crtc(struct drm_device *dev);
int mxsfb_create_output(struct drm_device *dev);
-void mxsfb_enable_axi_clk(struct mxsfb_drm_private *mxsfb);
-void mxsfb_disable_axi_clk(struct mxsfb_drm_private *mxsfb);
-
void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb);
void mxsfb_crtc_disable(struct mxsfb_drm_private *mxsfb);
void mxsfb_plane_atomic_update(struct mxsfb_drm_private *mxsfb,
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 09/14] dt-bindings: display: Add max-memory-bandwidth property for mxsfb
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Add new optional property 'max-memory-bandwidth', to limit the maximum
bandwidth used by the MXSFB_DRM driver.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
Documentation/devicetree/bindings/display/mxsfb.txt | 5 +++++
1 file changed, 5 insertions(+)
diff --git a/Documentation/devicetree/bindings/display/mxsfb.txt b/Documentation/devicetree/bindings/display/mxsfb.txt
index 472e1ea..c8dca50 100644
--- a/Documentation/devicetree/bindings/display/mxsfb.txt
+++ b/Documentation/devicetree/bindings/display/mxsfb.txt
@@ -14,6 +14,11 @@ Required properties:
- "pix" for the LCDIF block clock
- (MX6SX-only) "axi", "disp_axi" for the bus interface clock
+Optional properties:
+- max-memory-bandwidth: maximum bandwidth in bytes per second that the
+ controller can handle; if not present, the memory
+ interface is fast enough to handle all possible video modes
+
Required sub-nodes:
- port: The connection to an encoder chip.
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 08/14] drm/mxsfb: Add max-memory-bandwidth property for MXSFB
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Because of stability issues, we may want to limit the maximum bandwidth
required by the MXSFB (eLCDIF) driver.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_drv.c | 48 +++++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/mxsfb/mxsfb_drv.h | 2 ++
2 files changed, 50 insertions(+)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.c b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
index f95ba63..d8686c7 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
@@ -158,6 +158,49 @@ static const struct drm_mode_config_helper_funcs mxsfb_mode_config_helpers = {
.atomic_commit_tail = drm_atomic_helper_commit_tail_rpm,
};
+enum drm_mode_status mxsfb_pipe_mode_valid(struct drm_crtc *crtc,
+ const struct drm_display_mode *mode)
+{
+ struct drm_simple_display_pipe *pipe =
+ container_of(crtc, struct drm_simple_display_pipe, crtc);
+ struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
+ u32 bpp;
+ u64 bw;
+
+ if (!pipe->plane.state->fb)
+ bpp = 32;
+ else
+ bpp = pipe->plane.state->fb->format->depth;
+
+ bw = mode->crtc_clock * 1000;
+ bw = bw * mode->hdisplay * mode->vdisplay * (bpp / 8);
+ bw = div_u64(bw, mode->htotal * mode->vtotal);
+
+ if (mxsfb->max_bw && (bw > mxsfb->max_bw))
+ return MODE_BAD;
+
+ return MODE_OK;
+}
+
+static int mxsfb_pipe_check(struct drm_simple_display_pipe *pipe,
+ struct drm_plane_state *plane_state,
+ struct drm_crtc_state *crtc_state)
+{
+ struct drm_framebuffer *fb = plane_state->fb;
+ struct drm_framebuffer *old_fb = pipe->plane.state->fb;
+
+ /* force 'mode_changed' when fb pitches changed, since
+ * the pitch related registers configuration of LCDIF
+ * can not be done when LCDIF is running.
+ */
+ if (old_fb && likely(!crtc_state->mode_changed)) {
+ if (old_fb->pitches[0] != fb->pitches[0])
+ crtc_state->mode_changed = true;
+ }
+
+ return 0;
+}
+
static void mxsfb_pipe_enable(struct drm_simple_display_pipe *pipe,
struct drm_crtc_state *crtc_state,
struct drm_plane_state *plane_state)
@@ -244,6 +287,8 @@ static void mxsfb_pipe_disable_vblank(struct drm_simple_display_pipe *pipe)
}
static struct drm_simple_display_pipe_funcs mxsfb_funcs = {
+ .mode_valid = mxsfb_pipe_mode_valid,
+ .check = mxsfb_pipe_check,
.enable = mxsfb_pipe_enable,
.disable = mxsfb_pipe_disable,
.update = mxsfb_pipe_update,
@@ -283,6 +328,9 @@ static int mxsfb_load(struct drm_device *drm, unsigned long flags)
if (IS_ERR(mxsfb->clk_disp_axi))
mxsfb->clk_disp_axi = NULL;
+ of_property_read_u32(drm->dev->of_node, "max-memory-bandwidth",
+ &mxsfb->max_bw);
+
ret = dma_set_mask_and_coherent(drm->dev, DMA_BIT_MASK(32));
if (ret)
return ret;
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.h b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
index 8fb65d3..a178173 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
@@ -32,6 +32,8 @@ struct mxsfb_drm_private {
struct drm_connector *connector;
struct drm_panel *panel;
struct drm_bridge *bridge;
+
+ u32 max_bw;
};
int mxsfb_setup_crtc(struct drm_device *dev);
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 05/14] drm/mxsfb: Update register definitions using bit manipulation defines
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Use BIT(x) and GEN_MASK(h, l) for better representation the inside of
various registers.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_regs.h | 151 ++++++++++++++++++++++---------------
1 file changed, 89 insertions(+), 62 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
index 71426aa..9fcb1db 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
@@ -40,66 +40,93 @@
#define LCDC_AS_BUF 0x220
#define LCDC_AS_NEXT_BUF 0x230
-#define CTRL_SFTRST (1 << 31)
-#define CTRL_CLKGATE (1 << 30)
-#define CTRL_BYPASS_COUNT (1 << 19)
-#define CTRL_VSYNC_MODE (1 << 18)
-#define CTRL_DOTCLK_MODE (1 << 17)
-#define CTRL_DATA_SELECT (1 << 16)
-#define CTRL_SET_BUS_WIDTH(x) (((x) & 0x3) << 10)
-#define CTRL_GET_BUS_WIDTH(x) (((x) >> 10) & 0x3)
-#define CTRL_BUS_WIDTH_MASK (0x3 << 10)
-#define CTRL_SET_WORD_LENGTH(x) (((x) & 0x3) << 8)
-#define CTRL_GET_WORD_LENGTH(x) (((x) >> 8) & 0x3)
-#define CTRL_MASTER (1 << 5)
-#define CTRL_DF16 (1 << 3)
-#define CTRL_DF18 (1 << 2)
-#define CTRL_DF24 (1 << 1)
-#define CTRL_RUN (1 << 0)
-
-#define CTRL1_RECOVERY_ON_UNDERFLOW (1 << 24)
-#define CTRL1_FIFO_CLEAR (1 << 21)
-#define CTRL1_SET_BYTE_PACKAGING(x) (((x) & 0xf) << 16)
-#define CTRL1_GET_BYTE_PACKAGING(x) (((x) >> 16) & 0xf)
-#define CTRL1_CUR_FRAME_DONE_IRQ_EN (1 << 13)
-#define CTRL1_CUR_FRAME_DONE_IRQ (1 << 9)
-
-#define CTRL2_OUTSTANDING_REQS__REQ_16 (4 << 21)
-
-#define TRANSFER_COUNT_SET_VCOUNT(x) (((x) & 0xffff) << 16)
-#define TRANSFER_COUNT_GET_VCOUNT(x) (((x) >> 16) & 0xffff)
-#define TRANSFER_COUNT_SET_HCOUNT(x) ((x) & 0xffff)
-#define TRANSFER_COUNT_GET_HCOUNT(x) ((x) & 0xffff)
-
-#define VDCTRL0_ENABLE_PRESENT (1 << 28)
-#define VDCTRL0_VSYNC_ACT_HIGH (1 << 27)
-#define VDCTRL0_HSYNC_ACT_HIGH (1 << 26)
-#define VDCTRL0_DOTCLK_ACT_FALLING (1 << 25)
-#define VDCTRL0_ENABLE_ACT_HIGH (1 << 24)
-#define VDCTRL0_VSYNC_PERIOD_UNIT (1 << 21)
-#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT (1 << 20)
-#define VDCTRL0_HALF_LINE (1 << 19)
-#define VDCTRL0_HALF_LINE_MODE (1 << 18)
-#define VDCTRL0_SET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff)
-#define VDCTRL0_GET_VSYNC_PULSE_WIDTH(x) ((x) & 0x3ffff)
-
-#define VDCTRL2_SET_HSYNC_PERIOD(x) ((x) & 0x3ffff)
-#define VDCTRL2_GET_HSYNC_PERIOD(x) ((x) & 0x3ffff)
-
-#define VDCTRL3_MUX_SYNC_SIGNALS (1 << 29)
-#define VDCTRL3_VSYNC_ONLY (1 << 28)
-#define SET_HOR_WAIT_CNT(x) (((x) & 0xfff) << 16)
-#define GET_HOR_WAIT_CNT(x) (((x) >> 16) & 0xfff)
-#define SET_VERT_WAIT_CNT(x) ((x) & 0xffff)
-#define GET_VERT_WAIT_CNT(x) ((x) & 0xffff)
-
-#define VDCTRL4_SET_DOTCLK_DLY(x) (((x) & 0x7) << 29) /* v4 only */
-#define VDCTRL4_GET_DOTCLK_DLY(x) (((x) >> 29) & 0x7) /* v4 only */
-#define VDCTRL4_SYNC_SIGNALS_ON (1 << 18)
-#define SET_DOTCLK_H_VALID_DATA_CNT(x) ((x) & 0x3ffff)
-
-#define DEBUG0_HSYNC (1 < 26)
-#define DEBUG0_VSYNC (1 < 25)
+/* reg bit manipulation */
+#define REG_PUT(x, h, l) (((x) << (l)) & GENMASK(h, l))
+#define REG_GET(x, h, l) (((x) & GENMASK(h, l)) >> (l))
+
+#define CTRL_SFTRST BIT(31)
+#define CTRL_CLKGATE BIT(30)
+#define CTRL_SHIFT_DIR(x) REG_PUT((x), 26, 26)
+#define CTRL_SHIFT_NUM(x) REG_PUT((x), 25, 21)
+#define CTRL_BYPASS_COUNT BIT(19)
+#define CTRL_VSYNC_MODE BIT(18)
+#define CTRL_DOTCLK_MODE BIT(17)
+#define CTRL_DATA_SELECT BIT(16)
+#define CTRL_INPUT_SWIZZLE(x) REG_PUT((x), 15, 14)
+#define CTRL_CSC_SWIZZLE(x) REG_PUT((x), 13, 12)
+#define CTRL_SET_BUS_WIDTH(x) REG_PUT((x), 11, 10)
+#define CTRL_GET_BUS_WIDTH(x) REG_GET((x), 11, 10)
+#define CTRL_BUS_WIDTH_MASK REG_PUT((0x3), 11, 10)
+#define CTRL_SET_WORD_LENGTH(x) REG_PUT((x), 9, 8)
+#define CTRL_GET_WORD_LENGTH(x) REG_GET((x), 9, 8)
+#define CTRL_MASTER BIT(5)
+#define CTRL_DF16 BIT(3)
+#define CTRL_DF18 BIT(2)
+#define CTRL_DF24 BIT(1)
+#define CTRL_RUN BIT(0)
+
+#define CTRL1_RECOVERY_ON_UNDERFLOW BIT(24)
+#define CTRL1_FIFO_CLEAR BIT(21)
+
+/*
+ * BYTE_PACKAGING
+ *
+ * This bitfield is used to show which data bytes in a 32-bit word area valid.
+ * Default value 0xf indicates that all bytes are valid. For 8-bit transfers,
+ * any combination in this bitfield will mean valid data is present in the
+ * corresponding bytes. In the 16-bit mode, a 16-bit half-word is valid only if
+ * adjacent bits [1:0] or [3:2] or both are 1. A value of 0x0 will mean that
+ * none of the bytes are valid and should not be used. For example, set the bit
+ * field value to 0x7 if the display data is arranged in the 24-bit unpacked
+ * format (A-R-G-B where A value does not have be transmitted).
+ */
+#define CTRL1_SET_BYTE_PACKAGING(x) REG_PUT((x), 19, 16)
+#define CTRL1_GET_BYTE_PACKAGING(x) REG_GET((x), 19, 16)
+
+#define CTRL1_CUR_FRAME_DONE_IRQ_EN BIT(13)
+#define CTRL1_CUR_FRAME_DONE_IRQ BIT(9)
+
+#define CTRL2_OUTSTANDING_REQS(x) REG_PUT((x), 23, 21)
+#define REQ_1 0
+#define REQ_2 1
+#define REQ_4 2
+#define REQ_8 3
+#define REQ_16 4
+
+#define TRANSFER_COUNT_SET_VCOUNT(x) REG_PUT((x), 31, 16)
+#define TRANSFER_COUNT_GET_VCOUNT(x) REG_GET((x), 31, 16)
+#define TRANSFER_COUNT_SET_HCOUNT(x) REG_PUT((x), 15, 0)
+#define TRANSFER_COUNT_GET_HCOUNT(x) REG_GET((x), 15, 0)
+
+#define VDCTRL0_ENABLE_PRESENT BIT(28)
+#define VDCTRL0_VSYNC_ACT_HIGH BIT(27)
+#define VDCTRL0_HSYNC_ACT_HIGH BIT(26)
+#define VDCTRL0_DOTCLK_ACT_FALLING BIT(25)
+#define VDCTRL0_ENABLE_ACT_HIGH BIT(24)
+#define VDCTRL0_VSYNC_PERIOD_UNIT BIT(21)
+#define VDCTRL0_VSYNC_PULSE_WIDTH_UNIT BIT(20)
+#define VDCTRL0_HALF_LINE BIT(19)
+#define VDCTRL0_HALF_LINE_MODE BIT(18)
+#define VDCTRL0_SET_VSYNC_PULSE_WIDTH(x) REG_PUT((x), 17, 0)
+#define VDCTRL0_GET_VSYNC_PULSE_WIDTH(x) REG_GET((x), 17, 0)
+
+#define VDCTRL2_SET_HSYNC_PERIOD(x) REG_PUT((x), 15, 0)
+#define VDCTRL2_GET_HSYNC_PERIOD(x) REG_GET((x), 15, 0)
+
+#define VDCTRL3_MUX_SYNC_SIGNALS BIT(29)
+#define VDCTRL3_VSYNC_ONLY BIT(28)
+#define SET_HOR_WAIT_CNT(x) REG_PUT((x), 27, 16)
+#define GET_HOR_WAIT_CNT(x) REG_GET((x), 27, 16)
+#define SET_VERT_WAIT_CNT(x) REG_PUT((x), 15, 0)
+#define GET_VERT_WAIT_CNT(x) REG_GET((x), 15, 0)
+
+#define VDCTRL4_SET_DOTCLK_DLY(x) REG_PUT((x), 31, 29) /* v4 only */
+#define VDCTRL4_GET_DOTCLK_DLY(x) REG_GET((x), 31, 29) /* v4 only */
+#define VDCTRL4_SYNC_SIGNALS_ON BIT(18)
+#define SET_DOTCLK_H_VALID_DATA_CNT(x) REG_PUT((x), 17, 0)
+
+#define DEBUG0_HSYNC BIT(26)
+#define DEBUG0_VSYNC BIT(25)
#define MXSFB_MIN_XRES 120
#define MXSFB_MIN_YRES 120
@@ -116,7 +143,7 @@
#define STMLCDIF_18BIT 2 /* pixel data bus to the display is of 18 bit width */
#define STMLCDIF_24BIT 3 /* pixel data bus to the display is of 24 bit width */
-#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT (1 << 6)
-#define MXSFB_SYNC_DOTCLK_FALLING_ACT (1 << 7) /* negative edge sampling */
+#define MXSFB_SYNC_DATA_ENABLE_HIGH_ACT BIT(6)
+#define MXSFB_SYNC_DOTCLK_FALLING_ACT BIT(7) /* negative edge sampling */
#endif /* __MXSFB_REGS_H__ */
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 04/14] drm/mxsfb: Reset vital registers for a proper initialization
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Some of the registers, like LCDC_CTRL, CTRL2_OUTSTANDING_REQS and
CTRL1_RECOVERY_ON_UNDERFLOW needs to be properly cleared/initialized
for a better start and stop routine.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 12 ++++++++++++
1 file changed, 12 insertions(+)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index b69ace8..5e44f57 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -127,6 +127,10 @@ static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb)
clk_prepare_enable(mxsfb->clk_disp_axi);
clk_prepare_enable(mxsfb->clk);
+ if (mxsfb->devdata->ipversion >= 4)
+ writel(CTRL2_OUTSTANDING_REQS(REQ_16),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_SET);
+
/* If it was disabled, re-enable the mode again */
writel(CTRL_DOTCLK_MODE, mxsfb->base + LCDC_CTRL + REG_SET);
@@ -136,12 +140,19 @@ static void mxsfb_enable_controller(struct mxsfb_drm_private *mxsfb)
writel(reg, mxsfb->base + LCDC_VDCTRL4);
writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_SET);
+ writel(CTRL1_RECOVERY_ON_UNDERFLOW, mxsfb->base + LCDC_CTRL1 + REG_SET);
}
static void mxsfb_disable_controller(struct mxsfb_drm_private *mxsfb)
{
u32 reg;
+ if (mxsfb->devdata->ipversion >= 4)
+ writel(CTRL2_OUTSTANDING_REQS(0x7),
+ mxsfb->base + LCDC_V4_CTRL2 + REG_CLR);
+
+ writel(CTRL_RUN, mxsfb->base + LCDC_CTRL + REG_CLR);
+
/*
* Even if we disable the controller here, it will still continue
* until its FIFOs are running out of data
@@ -295,6 +306,7 @@ void mxsfb_crtc_enable(struct mxsfb_drm_private *mxsfb)
dma_addr_t paddr;
mxsfb_enable_axi_clk(mxsfb);
+ writel(0, mxsfb->base + LCDC_CTRL);
mxsfb_crtc_mode_set_nofb(mxsfb);
/* Write cur_buf as well to avoid an initial corrupt frame */
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 02/14] drm/mxsfb: Read bus flags from bridge if present
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
From: Guido Günther <agx@sigxcpu.org>
The bridge might have special requirmentes on the input bus. This
is e.g. used by the imx-nwl bridge.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Stefan Agner <stefan@agner.ch>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 5 ++++-
1 file changed, 4 insertions(+), 1 deletion(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index de09b93..b69ace8 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -209,7 +209,7 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
{
struct drm_device *drm = mxsfb->pipe.crtc.dev;
struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
- const u32 bus_flags = mxsfb->connector->display_info.bus_flags;
+ u32 bus_flags = mxsfb->connector->display_info.bus_flags;
u32 vdctrl0, vsync_pulse_len, hsync_pulse_len;
int err;
@@ -233,6 +233,9 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
clk_set_rate(mxsfb->clk, m->crtc_clock * 1000);
+ if (mxsfb->bridge && mxsfb->bridge->timings)
+ bus_flags = mxsfb->bridge->timings->input_bus_flags;
+
DRM_DEV_DEBUG_DRIVER(drm->dev, "Pixel clock: %dkHz (actual: %dkHz)\n",
m->crtc_clock,
(int)(clk_get_rate(mxsfb->clk) / 1000));
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 03/14] drm/mxsfb: Add defines for the rest of registers
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Some of the existing registers in this controller are not defined, but
also not used. Add them to the register definitions, so that they can be
easily used in future improvements or fixes.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_regs.h | 15 +++++++++++++++
1 file changed, 15 insertions(+)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_regs.h b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
index 932d7ea..71426aa 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_regs.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_regs.h
@@ -14,19 +14,31 @@
#define LCDC_CTRL 0x00
#define LCDC_CTRL1 0x10
+#define LCDC_V4_CTRL2 0x20
#define LCDC_V3_TRANSFER_COUNT 0x20
#define LCDC_V4_TRANSFER_COUNT 0x30
#define LCDC_V4_CUR_BUF 0x40
#define LCDC_V4_NEXT_BUF 0x50
#define LCDC_V3_CUR_BUF 0x30
#define LCDC_V3_NEXT_BUF 0x40
+#define LCDC_TIMING 0x60
#define LCDC_VDCTRL0 0x70
#define LCDC_VDCTRL1 0x80
#define LCDC_VDCTRL2 0x90
#define LCDC_VDCTRL3 0xa0
#define LCDC_VDCTRL4 0xb0
+#define LCDC_DVICTRL0 0xc0
+#define LCDC_DVICTRL1 0xd0
+#define LCDC_DVICTRL2 0xe0
+#define LCDC_DVICTRL3 0xf0
+#define LCDC_DVICTRL4 0x100
+#define LCDC_V4_DATA 0x180
+#define LCDC_V3_DATA 0x1b0
#define LCDC_V4_DEBUG0 0x1d0
#define LCDC_V3_DEBUG0 0x1f0
+#define LCDC_AS_CTRL 0x210
+#define LCDC_AS_BUF 0x220
+#define LCDC_AS_NEXT_BUF 0x230
#define CTRL_SFTRST (1 << 31)
#define CTRL_CLKGATE (1 << 30)
@@ -45,12 +57,15 @@
#define CTRL_DF24 (1 << 1)
#define CTRL_RUN (1 << 0)
+#define CTRL1_RECOVERY_ON_UNDERFLOW (1 << 24)
#define CTRL1_FIFO_CLEAR (1 << 21)
#define CTRL1_SET_BYTE_PACKAGING(x) (((x) & 0xf) << 16)
#define CTRL1_GET_BYTE_PACKAGING(x) (((x) >> 16) & 0xf)
#define CTRL1_CUR_FRAME_DONE_IRQ_EN (1 << 13)
#define CTRL1_CUR_FRAME_DONE_IRQ (1 << 9)
+#define CTRL2_OUTSTANDING_REQS__REQ_16 (4 << 21)
+
#define TRANSFER_COUNT_SET_VCOUNT(x) (((x) & 0xffff) << 16)
#define TRANSFER_COUNT_GET_VCOUNT(x) (((x) >> 16) & 0xffff)
#define TRANSFER_COUNT_SET_HCOUNT(x) ((x) & 0xffff)
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH v4 01/14] drm/mxsfb: Update mxsfb to support a bridge
From: Robert Chiras @ 2019-08-29 11:30 UTC (permalink / raw)
To: Guido Günther, Marek Vasut, Stefan Agner, David Airlie,
Daniel Vetter, Rob Herring, Mark Rutland, Shawn Guo, Sascha Hauer,
Fabio Estevam
Cc: devicetree, linux-kernel, dri-devel, NXP Linux Team,
Pengutronix Kernel Team, linux-arm-kernel
In-Reply-To: <1567078215-31601-1-git-send-email-robert.chiras@nxp.com>
Currently, the MXSFB DRM driver only supports a panel. But, its output
display signal can also be redirected to another encoder, like a DSI
controller. In this case, that DSI controller may act like a drm_bridge.
In order support this use-case too, this patch adds support for drm_bridge
in mxsfb.
Signed-off-by: Robert Chiras <robert.chiras@nxp.com>
Tested-by: Guido Günther <agx@sigxcpu.org>
---
drivers/gpu/drm/mxsfb/mxsfb_crtc.c | 17 +++++++++++---
drivers/gpu/drm/mxsfb/mxsfb_drv.c | 46 +++++++++++++++++++++++++++++++++-----
drivers/gpu/drm/mxsfb/mxsfb_drv.h | 4 +++-
drivers/gpu/drm/mxsfb/mxsfb_out.c | 26 +++++++++++----------
4 files changed, 72 insertions(+), 21 deletions(-)
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
index 1242156..de09b93 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_crtc.c
@@ -95,8 +95,11 @@ static void mxsfb_set_bus_fmt(struct mxsfb_drm_private *mxsfb)
reg = readl(mxsfb->base + LCDC_CTRL);
- if (mxsfb->connector.display_info.num_bus_formats)
- bus_format = mxsfb->connector.display_info.bus_formats[0];
+ if (mxsfb->connector->display_info.num_bus_formats)
+ bus_format = mxsfb->connector->display_info.bus_formats[0];
+
+ DRM_DEV_DEBUG_DRIVER(drm->dev, "Using bus_format: 0x%08X\n",
+ bus_format);
reg &= ~CTRL_BUS_WIDTH_MASK;
switch (bus_format) {
@@ -204,8 +207,9 @@ static dma_addr_t mxsfb_get_fb_paddr(struct mxsfb_drm_private *mxsfb)
static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
{
+ struct drm_device *drm = mxsfb->pipe.crtc.dev;
struct drm_display_mode *m = &mxsfb->pipe.crtc.state->adjusted_mode;
- const u32 bus_flags = mxsfb->connector.display_info.bus_flags;
+ const u32 bus_flags = mxsfb->connector->display_info.bus_flags;
u32 vdctrl0, vsync_pulse_len, hsync_pulse_len;
int err;
@@ -229,6 +233,13 @@ static void mxsfb_crtc_mode_set_nofb(struct mxsfb_drm_private *mxsfb)
clk_set_rate(mxsfb->clk, m->crtc_clock * 1000);
+ DRM_DEV_DEBUG_DRIVER(drm->dev, "Pixel clock: %dkHz (actual: %dkHz)\n",
+ m->crtc_clock,
+ (int)(clk_get_rate(mxsfb->clk) / 1000));
+ DRM_DEV_DEBUG_DRIVER(drm->dev, "Connector bus_flags: 0x%08X\n",
+ bus_flags);
+ DRM_DEV_DEBUG_DRIVER(drm->dev, "Mode flags: 0x%08X\n", m->flags);
+
writel(TRANSFER_COUNT_SET_VCOUNT(m->crtc_vdisplay) |
TRANSFER_COUNT_SET_HCOUNT(m->crtc_hdisplay),
mxsfb->base + mxsfb->devdata->transfer_count);
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.c b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
index e850633..497cf44 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.c
@@ -101,9 +101,25 @@ static void mxsfb_pipe_enable(struct drm_simple_display_pipe *pipe,
struct drm_crtc_state *crtc_state,
struct drm_plane_state *plane_state)
{
+ struct drm_connector *connector;
struct mxsfb_drm_private *mxsfb = drm_pipe_to_mxsfb_drm_private(pipe);
struct drm_device *drm = pipe->plane.dev;
+ if (!mxsfb->connector) {
+ list_for_each_entry(connector,
+ &drm->mode_config.connector_list,
+ head)
+ if (connector->encoder == &mxsfb->pipe.encoder) {
+ mxsfb->connector = connector;
+ break;
+ }
+ }
+
+ if (!mxsfb->connector) {
+ dev_warn(drm->dev, "No connector attached, using default\n");
+ mxsfb->connector = &mxsfb->panel_connector;
+ }
+
pm_runtime_get_sync(drm->dev);
drm_panel_prepare(mxsfb->panel);
mxsfb_crtc_enable(mxsfb);
@@ -129,6 +145,9 @@ static void mxsfb_pipe_disable(struct drm_simple_display_pipe *pipe)
drm_crtc_send_vblank_event(crtc, event);
}
spin_unlock_irq(&drm->event_lock);
+
+ if (mxsfb->connector != &mxsfb->panel_connector)
+ mxsfb->connector = NULL;
}
static void mxsfb_pipe_update(struct drm_simple_display_pipe *pipe,
@@ -226,16 +245,33 @@ static int mxsfb_load(struct drm_device *drm, unsigned long flags)
ret = drm_simple_display_pipe_init(drm, &mxsfb->pipe, &mxsfb_funcs,
mxsfb_formats, ARRAY_SIZE(mxsfb_formats), NULL,
- &mxsfb->connector);
+ mxsfb->connector);
if (ret < 0) {
dev_err(drm->dev, "Cannot setup simple display pipe\n");
goto err_vblank;
}
- ret = drm_panel_attach(mxsfb->panel, &mxsfb->connector);
- if (ret) {
- dev_err(drm->dev, "Cannot connect panel\n");
- goto err_vblank;
+ /*
+ * Attach panel only if there is one.
+ * If there is no panel attach, it must be a bridge. In this case, we
+ * need a reference to its connector for a proper initialization.
+ * We will do this check in pipe->enable(), since the connector won't
+ * be attached to an encoder until then.
+ */
+
+ if (mxsfb->panel) {
+ ret = drm_panel_attach(mxsfb->panel, mxsfb->connector);
+ if (ret) {
+ dev_err(drm->dev, "Cannot connect panel: %d\n", ret);
+ goto err_vblank;
+ }
+ } else if (mxsfb->bridge) {
+ ret = drm_simple_display_pipe_attach_bridge(&mxsfb->pipe,
+ mxsfb->bridge);
+ if (ret) {
+ dev_err(drm->dev, "Cannot connect bridge: %d\n", ret);
+ goto err_vblank;
+ }
}
drm->mode_config.min_width = MXSFB_MIN_XRES;
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_drv.h b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
index d975300..0b65b51 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_drv.h
+++ b/drivers/gpu/drm/mxsfb/mxsfb_drv.h
@@ -27,8 +27,10 @@ struct mxsfb_drm_private {
struct clk *clk_disp_axi;
struct drm_simple_display_pipe pipe;
- struct drm_connector connector;
+ struct drm_connector panel_connector;
+ struct drm_connector *connector;
struct drm_panel *panel;
+ struct drm_bridge *bridge;
};
int mxsfb_setup_crtc(struct drm_device *dev);
diff --git a/drivers/gpu/drm/mxsfb/mxsfb_out.c b/drivers/gpu/drm/mxsfb/mxsfb_out.c
index be36f4d..4eb9474 100644
--- a/drivers/gpu/drm/mxsfb/mxsfb_out.c
+++ b/drivers/gpu/drm/mxsfb/mxsfb_out.c
@@ -21,7 +21,8 @@
static struct mxsfb_drm_private *
drm_connector_to_mxsfb_drm_private(struct drm_connector *connector)
{
- return container_of(connector, struct mxsfb_drm_private, connector);
+ return container_of(connector, struct mxsfb_drm_private,
+ panel_connector);
}
static int mxsfb_panel_get_modes(struct drm_connector *connector)
@@ -76,22 +77,23 @@ static const struct drm_connector_funcs mxsfb_panel_connector_funcs = {
int mxsfb_create_output(struct drm_device *drm)
{
struct mxsfb_drm_private *mxsfb = drm->dev_private;
- struct drm_panel *panel;
int ret;
- ret = drm_of_find_panel_or_bridge(drm->dev->of_node, 0, 0, &panel, NULL);
+ ret = drm_of_find_panel_or_bridge(drm->dev->of_node, 0, 0,
+ &mxsfb->panel, &mxsfb->bridge);
if (ret)
return ret;
- mxsfb->connector.dpms = DRM_MODE_DPMS_OFF;
- mxsfb->connector.polled = 0;
- drm_connector_helper_add(&mxsfb->connector,
- &mxsfb_panel_connector_helper_funcs);
- ret = drm_connector_init(drm, &mxsfb->connector,
- &mxsfb_panel_connector_funcs,
- DRM_MODE_CONNECTOR_Unknown);
- if (!ret)
- mxsfb->panel = panel;
+ if (mxsfb->panel) {
+ mxsfb->connector = &mxsfb->panel_connector;
+ mxsfb->connector->dpms = DRM_MODE_DPMS_OFF;
+ mxsfb->connector->polled = 0;
+ drm_connector_helper_add(mxsfb->connector,
+ &mxsfb_panel_connector_helper_funcs);
+ ret = drm_connector_init(drm, mxsfb->connector,
+ &mxsfb_panel_connector_funcs,
+ DRM_MODE_CONNECTOR_Unknown);
+ }
return ret;
}
--
2.7.4
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* Re: [PATCH 7/8] media: cedrus: Add support for holding capture buffer
From: Hans Verkuil @ 2019-08-29 11:23 UTC (permalink / raw)
To: Jernej Skrabec, mchehab, paul.kocialkowski, mripard
Cc: devel, pawel, acourbot, jonas, gregkh, wens, tfiga, kyungmin.park,
linux-arm-kernel, linux-media, ezequiel, linux-kernel,
m.szyprowski
In-Reply-To: <20190822194500.2071-8-jernej.skrabec@siol.net>
On 8/22/19 9:44 PM, Jernej Skrabec wrote:
> When frame contains multiple slices and driver works in slice mode, it's
> more efficient to hold capture buffer in queue until all slices of a
> same frame are decoded.
>
> Add support for that to Cedrus driver by exposing and implementing
> V4L2_BUF_CAP_SUPPORTS_M2M_HOLD_CAPTURE_BUF capability.
>
> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
> ---
> drivers/staging/media/sunxi/cedrus/cedrus_dec.c | 9 +++++++++
> drivers/staging/media/sunxi/cedrus/cedrus_hw.c | 8 +++++---
> drivers/staging/media/sunxi/cedrus/cedrus_video.c | 1 +
> 3 files changed, 15 insertions(+), 3 deletions(-)
>
> diff --git a/drivers/staging/media/sunxi/cedrus/cedrus_dec.c b/drivers/staging/media/sunxi/cedrus/cedrus_dec.c
> index d7b54accfe83..68462b99750e 100644
> --- a/drivers/staging/media/sunxi/cedrus/cedrus_dec.c
> +++ b/drivers/staging/media/sunxi/cedrus/cedrus_dec.c
> @@ -31,6 +31,14 @@ void cedrus_device_run(void *priv)
>
> run.src = v4l2_m2m_next_src_buf(ctx->fh.m2m_ctx);
> run.dst = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx);
> +
> + if (v4l2_m2m_release_capture_buf(run.src, run.dst)) {
> + v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
> + v4l2_m2m_buf_done(run.dst, VB2_BUF_STATE_DONE);
> + run.dst = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx);
> + }
> + run.dst->is_held = run.src->flags & V4L2_BUF_FLAG_M2M_HOLD_CAPTURE_BUF;
> +
> run.first_slice =
> run.src->vb2_buf.timestamp != run.dst->vb2_buf.timestamp;
>
> @@ -46,6 +54,7 @@ void cedrus_device_run(void *priv)
> V4L2_CID_MPEG_VIDEO_MPEG2_SLICE_PARAMS);
> run.mpeg2.quantization = cedrus_find_control_data(ctx,
> V4L2_CID_MPEG_VIDEO_MPEG2_QUANTIZATION);
> + run.dst->is_held = false;
> break;
>
> case V4L2_PIX_FMT_H264_SLICE:
> diff --git a/drivers/staging/media/sunxi/cedrus/cedrus_hw.c b/drivers/staging/media/sunxi/cedrus/cedrus_hw.c
> index a942cd9bed57..99fedec80224 100644
> --- a/drivers/staging/media/sunxi/cedrus/cedrus_hw.c
> +++ b/drivers/staging/media/sunxi/cedrus/cedrus_hw.c
> @@ -122,7 +122,7 @@ static irqreturn_t cedrus_irq(int irq, void *data)
> dev->dec_ops[ctx->current_codec]->irq_clear(ctx);
>
> src_buf = v4l2_m2m_src_buf_remove(ctx->fh.m2m_ctx);
> - dst_buf = v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
> + dst_buf = v4l2_m2m_next_dst_buf(ctx->fh.m2m_ctx);
>
> if (!src_buf || !dst_buf) {
> v4l2_err(&dev->v4l2_dev,
> @@ -136,8 +136,10 @@ static irqreturn_t cedrus_irq(int irq, void *data)
> state = VB2_BUF_STATE_DONE;
>
> v4l2_m2m_buf_done(src_buf, state);
> - v4l2_m2m_buf_done(dst_buf, state);
> -
> + if (!dst_buf->is_held) {
> + v4l2_m2m_dst_buf_remove(ctx->fh.m2m_ctx);
> + v4l2_m2m_buf_done(dst_buf, state);
> + }
> v4l2_m2m_job_finish(ctx->dev->m2m_dev, ctx->fh.m2m_ctx);
>
> return IRQ_HANDLED;
> diff --git a/drivers/staging/media/sunxi/cedrus/cedrus_video.c b/drivers/staging/media/sunxi/cedrus/cedrus_video.c
> index eeee3efd247b..5153b2bba21e 100644
> --- a/drivers/staging/media/sunxi/cedrus/cedrus_video.c
> +++ b/drivers/staging/media/sunxi/cedrus/cedrus_video.c
> @@ -515,6 +515,7 @@ int cedrus_queue_init(void *priv, struct vb2_queue *src_vq,
> src_vq->type = V4L2_BUF_TYPE_VIDEO_OUTPUT;
> src_vq->io_modes = VB2_MMAP | VB2_DMABUF;
> src_vq->drv_priv = ctx;
> + src_vq->subsystem_flags = VB2_V4L2_FL_SUPPORTS_M2M_HOLD_CAPTURE_BUF;
This isn't quite right: this flag should only be set for formats that support
slicing. So cedrus_s_fmt_vid_out() should set this for H264, but clear it for
MPEG2.
Looking at the cedrus code it seems that it does not set an initial default output
format after opening the video device. This seems wrong to me. If it did set a
default output format, then src_vq->subsystem_flags should set this flag corresponding
to the default output format.
> src_vq->buf_struct_size = sizeof(struct cedrus_buffer);
> src_vq->min_buffers_needed = 1;
> src_vq->ops = &cedrus_qops;
>
Regards,
Hans
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply
* [PATCH 7/7] x86: vdso: Remove unused VDSO_HAS_32BIT_FALLBACK
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
As a consequence of Commit 623fa33f7bd6 ("lib:vdso: Remove
VDSO_HAS_32BIT_FALLBACK") VDSO_HAS_32BIT_FALLBACK define is not
required anymore hence can be removed.
Remove unused VDSO_HAS_32BIT_FALLBACK from x86 vdso.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
arch/x86/include/asm/vdso/gettimeofday.h | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/x86/include/asm/vdso/gettimeofday.h b/arch/x86/include/asm/vdso/gettimeofday.h
index e9ee139cf29e..52c3bcd672cf 100644
--- a/arch/x86/include/asm/vdso/gettimeofday.h
+++ b/arch/x86/include/asm/vdso/gettimeofday.h
@@ -96,8 +96,6 @@ long clock_getres_fallback(clockid_t _clkid, struct __kernel_timespec *_ts)
#else
-#define VDSO_HAS_32BIT_FALLBACK 1
-
static __always_inline
long clock_gettime_fallback(clockid_t _clkid, struct __kernel_timespec *_ts)
{
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 6/7] mips: vdso: Remove unused VDSO_HAS_32BIT_FALLBACK
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
As a consequence of Commit 623fa33f7bd6 ("lib:vdso: Remove
VDSO_HAS_32BIT_FALLBACK") VDSO_HAS_32BIT_FALLBACK define is not
required anymore hence can be removed.
Remove unused VDSO_HAS_32BIT_FALLBACK from mips vdso.
Cc: Paul Burton <paul.burton@mips.com>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
arch/mips/include/asm/vdso/gettimeofday.h | 2 --
1 file changed, 2 deletions(-)
diff --git a/arch/mips/include/asm/vdso/gettimeofday.h b/arch/mips/include/asm/vdso/gettimeofday.h
index e78462e8ca2e..5ad2b086626d 100644
--- a/arch/mips/include/asm/vdso/gettimeofday.h
+++ b/arch/mips/include/asm/vdso/gettimeofday.h
@@ -107,8 +107,6 @@ static __always_inline int clock_getres_fallback(
#if _MIPS_SIM != _MIPS_SIM_ABI64
-#define VDSO_HAS_32BIT_FALLBACK 1
-
static __always_inline long clock_gettime32_fallback(
clockid_t _clkid,
struct old_timespec32 *_ts)
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 5/7] arm64: compat: vdso: Remove unused VDSO_HAS_32BIT_FALLBACK
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
As a consequence of Commit 623fa33f7bd6 ("lib:vdso: Remove
VDSO_HAS_32BIT_FALLBACK") VDSO_HAS_32BIT_FALLBACK define is not
required anymore hence can be removed.
Remove unused VDSO_HAS_32BIT_FALLBACK from arm64 compat vdso.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
arch/arm64/include/asm/vdso/compat_gettimeofday.h | 1 -
1 file changed, 1 deletion(-)
diff --git a/arch/arm64/include/asm/vdso/compat_gettimeofday.h b/arch/arm64/include/asm/vdso/compat_gettimeofday.h
index fe7afe0f1a3d..537b1e695365 100644
--- a/arch/arm64/include/asm/vdso/compat_gettimeofday.h
+++ b/arch/arm64/include/asm/vdso/compat_gettimeofday.h
@@ -16,7 +16,6 @@
#define VDSO_HAS_CLOCK_GETRES 1
-#define VDSO_HAS_32BIT_FALLBACK 1
#define BUILD_VDSO32 1
static __always_inline
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 4/7] lib: vdso: Remove VDSO_HAS_32BIT_FALLBACK
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
VDSO_HAS_32BIT_FALLBACK was introduced to address a regression which
caused seccomp to deny access to the applications to clock_gettime64()
and clock_getres64() because they are not enabled in the existing
filters.
The purpose of VDSO_HAS_32BIT_FALLBACK was to simplify the conditional
implementation of __cvdso_clock_get*time32() variants.
Now that all the architectures that support the generic vDSO library
have been converted to support the 32 bit fallbacks the conditional
can be removed.
Cc: Thomas Gleixner <tglx@linutronix.de>
CC: Andy Lutomirski <luto@kernel.org>
References: c60a32ea4f45 ("lib/vdso/32: Provide legacy syscall fallbacks")
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
lib/vdso/gettimeofday.c | 10 ----------
1 file changed, 10 deletions(-)
diff --git a/lib/vdso/gettimeofday.c b/lib/vdso/gettimeofday.c
index a86e89e6dedc..2c4b311c226d 100644
--- a/lib/vdso/gettimeofday.c
+++ b/lib/vdso/gettimeofday.c
@@ -126,13 +126,8 @@ __cvdso_clock_gettime32(clockid_t clock, struct old_timespec32 *res)
ret = __cvdso_clock_gettime_common(clock, &ts);
-#ifdef VDSO_HAS_32BIT_FALLBACK
if (unlikely(ret))
return clock_gettime32_fallback(clock, res);
-#else
- if (unlikely(ret))
- ret = clock_gettime_fallback(clock, &ts);
-#endif
if (likely(!ret)) {
res->tv_sec = ts.tv_sec;
@@ -240,13 +235,8 @@ __cvdso_clock_getres_time32(clockid_t clock, struct old_timespec32 *res)
ret = __cvdso_clock_getres_common(clock, &ts);
-#ifdef VDSO_HAS_32BIT_FALLBACK
if (unlikely(ret))
return clock_getres32_fallback(clock, res);
-#else
- if (unlikely(ret))
- ret = clock_getres_fallback(clock, &ts);
-#endif
if (likely(!ret)) {
res->tv_sec = ts.tv_sec;
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 3/7] mips: compat: vdso: Use legacy syscalls as fallback
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
The generic VDSO implementation uses the Y2038 safe clock_gettime64() and
clock_getres_time64() syscalls as fallback for 32bit VDSO. This breaks
seccomp setups because these syscalls might be not (yet) allowed.
Implement the 32bit variants which use the legacy syscalls and select the
variant in the core library.
The 64bit time variants are not removed because they are required for the
time64 based vdso accessors.
Cc: Paul Burton <paul.burton@mips.com>
Fixes: 00b26474c2f1 ("lib/vdso: Provide generic VDSO implementation")
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
arch/mips/include/asm/vdso/gettimeofday.h | 45 +++++++++++++++++++++++
arch/mips/vdso/config-n32-o32-env.c | 1 +
2 files changed, 46 insertions(+)
diff --git a/arch/mips/include/asm/vdso/gettimeofday.h b/arch/mips/include/asm/vdso/gettimeofday.h
index c59fe08b0347..e78462e8ca2e 100644
--- a/arch/mips/include/asm/vdso/gettimeofday.h
+++ b/arch/mips/include/asm/vdso/gettimeofday.h
@@ -105,6 +105,51 @@ static __always_inline int clock_getres_fallback(
return error ? -ret : ret;
}
+#if _MIPS_SIM != _MIPS_SIM_ABI64
+
+#define VDSO_HAS_32BIT_FALLBACK 1
+
+static __always_inline long clock_gettime32_fallback(
+ clockid_t _clkid,
+ struct old_timespec32 *_ts)
+{
+ register struct old_timespec32 *ts asm("a1") = _ts;
+ register clockid_t clkid asm("a0") = _clkid;
+ register long ret asm("v0");
+ register long nr asm("v0") = __NR_clock_gettime;
+ register long error asm("a3");
+
+ asm volatile(
+ " syscall\n"
+ : "=r" (ret), "=r" (error)
+ : "r" (clkid), "r" (ts), "r" (nr)
+ : "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+ "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+
+ return error ? -ret : ret;
+}
+
+static __always_inline int clock_getres32_fallback(
+ clockid_t _clkid,
+ struct old_timespec32 *_ts)
+{
+ register struct old_timespec32 *ts asm("a1") = _ts;
+ register clockid_t clkid asm("a0") = _clkid;
+ register long ret asm("v0");
+ register long nr asm("v0") = __NR_clock_getres;
+ register long error asm("a3");
+
+ asm volatile(
+ " syscall\n"
+ : "=r" (ret), "=r" (error)
+ : "r" (clkid), "r" (ts), "r" (nr)
+ : "$1", "$3", "$8", "$9", "$10", "$11", "$12", "$13",
+ "$14", "$15", "$24", "$25", "hi", "lo", "memory");
+
+ return error ? -ret : ret;
+}
+#endif
+
#ifdef CONFIG_CSRC_R4K
static __always_inline u64 read_r4k_count(void)
diff --git a/arch/mips/vdso/config-n32-o32-env.c b/arch/mips/vdso/config-n32-o32-env.c
index 7f8d957abd4a..0011a632aef2 100644
--- a/arch/mips/vdso/config-n32-o32-env.c
+++ b/arch/mips/vdso/config-n32-o32-env.c
@@ -10,6 +10,7 @@
*/
#undef CONFIG_64BIT
+#define BUILD_VDSO32
#define CONFIG_32BIT 1
#define CONFIG_GENERIC_ATOMIC64 1
#define BUILD_VDSO32_64
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 2/7] lib: vdso: Build 32 bit specific functions in the right context
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
clock_gettime32 and clock_getres_time32 should be compiled only with a
32 bit vdso library.
Exclude these symbols when BUILD_VDSO32 is not defined.
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
lib/vdso/gettimeofday.c | 4 ++++
1 file changed, 4 insertions(+)
diff --git a/lib/vdso/gettimeofday.c b/lib/vdso/gettimeofday.c
index e630e7ff57f1..a86e89e6dedc 100644
--- a/lib/vdso/gettimeofday.c
+++ b/lib/vdso/gettimeofday.c
@@ -117,6 +117,7 @@ __cvdso_clock_gettime(clockid_t clock, struct __kernel_timespec *ts)
return 0;
}
+#ifdef BUILD_VDSO32
static __maybe_unused int
__cvdso_clock_gettime32(clockid_t clock, struct old_timespec32 *res)
{
@@ -139,6 +140,7 @@ __cvdso_clock_gettime32(clockid_t clock, struct old_timespec32 *res)
}
return ret;
}
+#endif /* BUILD_VDSO32 */
static __maybe_unused int
__cvdso_gettimeofday(struct __kernel_old_timeval *tv, struct timezone *tz)
@@ -229,6 +231,7 @@ int __cvdso_clock_getres(clockid_t clock, struct __kernel_timespec *res)
return 0;
}
+#ifdef BUILD_VDSO32
static __maybe_unused int
__cvdso_clock_getres_time32(clockid_t clock, struct old_timespec32 *res)
{
@@ -251,4 +254,5 @@ __cvdso_clock_getres_time32(clockid_t clock, struct old_timespec32 *res)
}
return ret;
}
+#endif /* BUILD_VDSO32 */
#endif /* VDSO_HAS_CLOCK_GETRES */
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 1/7] arm64: compat: vdso: Expose BUILD_VDSO32
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
In-Reply-To: <20190829111843.41003-1-vincenzo.frascino@arm.com>
clock_gettime32 and clock_getres_time32 should be compiled only with the
32 bit vdso library.
Expose BUILD_VDSO32 when arm64 compat is compiled, to provide an
indication to the generic library to include these symbols.
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
---
arch/arm64/include/asm/vdso/compat_gettimeofday.h | 1 +
1 file changed, 1 insertion(+)
diff --git a/arch/arm64/include/asm/vdso/compat_gettimeofday.h b/arch/arm64/include/asm/vdso/compat_gettimeofday.h
index c50ee1b7d5cd..fe7afe0f1a3d 100644
--- a/arch/arm64/include/asm/vdso/compat_gettimeofday.h
+++ b/arch/arm64/include/asm/vdso/compat_gettimeofday.h
@@ -17,6 +17,7 @@
#define VDSO_HAS_CLOCK_GETRES 1
#define VDSO_HAS_32BIT_FALLBACK 1
+#define BUILD_VDSO32 1
static __always_inline
int gettimeofday_fallback(struct __kernel_old_timeval *_tv,
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 0/7] vdso: Complete the conversion to 32bit syscalls
From: Vincenzo Frascino @ 2019-08-29 11:18 UTC (permalink / raw)
To: linux-arch, linux-arm-kernel, linux-kernel, linux-mips
Cc: catalin.marinas, 0x7f454c46, salyzyn, paul.burton, luto, tglx,
will
This patch series is a follow up to "lib/vdso, x86/vdso: Fix fallout
from generic VDSO conversion" [1].
The main purpose is to complete the 32bit vDSOs conversion to use the
legacy 32bit syscalls as a fallback. With the conversion of all the
architectures present in -next complete, this patch series removes as
well the conditional choice in between 32 and 64 bit for 32bit vDSOs.
This series has been rebased on linux-next/master.
[1] https://lkml.org/lkml/2019/7/28/86
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Will Deacon <will@kernel.org>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: Andy Lutomirski <luto@kernel.org>
Signed-off-by: Vincenzo Frascino <vincenzo.frascino@arm.com>
Vincenzo Frascino (7):
arm64: compat: vdso: Expose BUILD_VDSO32
lib: vdso: Build 32 bit specific functions in the right context
mips: compat: vdso: Use legacy syscalls as fallback
lib: vdso: Remove VDSO_HAS_32BIT_FALLBACK
arm64: compat: vdso: Remove unused VDSO_HAS_32BIT_FALLBACK
mips: vdso: Remove unused VDSO_HAS_32BIT_FALLBACK
x86: vdso: Remove unused VDSO_HAS_32BIT_FALLBACK
.../include/asm/vdso/compat_gettimeofday.h | 2 +-
arch/mips/include/asm/vdso/gettimeofday.h | 43 +++++++++++++++++++
arch/mips/vdso/config-n32-o32-env.c | 1 +
arch/x86/include/asm/vdso/gettimeofday.h | 2 -
lib/vdso/gettimeofday.c | 14 ++----
5 files changed, 49 insertions(+), 13 deletions(-)
--
2.23.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply
* [PATCH 5/5] iommu: virt: Use iommu_put_resv_regions_simple()
From: Thierry Reding @ 2019-08-29 11:17 UTC (permalink / raw)
To: Joerg Roedel
Cc: Jean-Philippe Brucker, Will Deacon, linux-kernel, virtualization,
iommu, Robin Murphy, David Woodhouse, linux-arm-kernel
In-Reply-To: <20190829111752.17513-1-thierry.reding@gmail.com>
From: Thierry Reding <treding@nvidia.com>
Use the new standard function instead of open-coding it.
Cc: Jean-Philippe Brucker <jean-philippe@linaro.org>
Cc: virtualization@lists.linux-foundation.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
drivers/iommu/virtio-iommu.c | 14 +++-----------
1 file changed, 3 insertions(+), 11 deletions(-)
diff --git a/drivers/iommu/virtio-iommu.c b/drivers/iommu/virtio-iommu.c
index 3ea9d7682999..bc3c7ab7f996 100644
--- a/drivers/iommu/virtio-iommu.c
+++ b/drivers/iommu/virtio-iommu.c
@@ -838,14 +838,6 @@ static void viommu_get_resv_regions(struct device *dev, struct list_head *head)
iommu_dma_get_resv_regions(dev, head);
}
-static void viommu_put_resv_regions(struct device *dev, struct list_head *head)
-{
- struct iommu_resv_region *entry, *next;
-
- list_for_each_entry_safe(entry, next, head, list)
- kfree(entry);
-}
-
static struct iommu_ops viommu_ops;
static struct virtio_driver virtio_iommu_drv;
@@ -915,7 +907,7 @@ static int viommu_add_device(struct device *dev)
err_unlink_dev:
iommu_device_unlink(&viommu->iommu, dev);
err_free_dev:
- viommu_put_resv_regions(dev, &vdev->resv_regions);
+ iommu_put_resv_regions_simple(dev, &vdev->resv_regions);
kfree(vdev);
return ret;
@@ -933,7 +925,7 @@ static void viommu_remove_device(struct device *dev)
iommu_group_remove_device(dev);
iommu_device_unlink(&vdev->viommu->iommu, dev);
- viommu_put_resv_regions(dev, &vdev->resv_regions);
+ iommu_put_resv_regions_simple(dev, &vdev->resv_regions);
kfree(vdev);
}
@@ -962,7 +954,7 @@ static struct iommu_ops viommu_ops = {
.remove_device = viommu_remove_device,
.device_group = viommu_device_group,
.get_resv_regions = viommu_get_resv_regions,
- .put_resv_regions = viommu_put_resv_regions,
+ .put_resv_regions = iommu_put_resv_regions_simple,
.of_xlate = viommu_of_xlate,
};
--
2.22.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 4/5] iommu: intel: Use iommu_put_resv_regions_simple()
From: Thierry Reding @ 2019-08-29 11:17 UTC (permalink / raw)
To: Joerg Roedel
Cc: Jean-Philippe Brucker, Will Deacon, linux-kernel, virtualization,
iommu, Robin Murphy, David Woodhouse, linux-arm-kernel
In-Reply-To: <20190829111752.17513-1-thierry.reding@gmail.com>
From: Thierry Reding <treding@nvidia.com>
Use the new standard function instead of open-coding it.
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
drivers/iommu/intel-iommu.c | 11 +----------
1 file changed, 1 insertion(+), 10 deletions(-)
diff --git a/drivers/iommu/intel-iommu.c b/drivers/iommu/intel-iommu.c
index 4658cda6f3d2..2fe5da41c786 100644
--- a/drivers/iommu/intel-iommu.c
+++ b/drivers/iommu/intel-iommu.c
@@ -5386,15 +5386,6 @@ static void intel_iommu_get_resv_regions(struct device *device,
list_add_tail(®->list, head);
}
-static void intel_iommu_put_resv_regions(struct device *dev,
- struct list_head *head)
-{
- struct iommu_resv_region *entry, *next;
-
- list_for_each_entry_safe(entry, next, head, list)
- kfree(entry);
-}
-
int intel_iommu_enable_pasid(struct intel_iommu *iommu, struct device *dev)
{
struct device_domain_info *info;
@@ -5629,7 +5620,7 @@ const struct iommu_ops intel_iommu_ops = {
.add_device = intel_iommu_add_device,
.remove_device = intel_iommu_remove_device,
.get_resv_regions = intel_iommu_get_resv_regions,
- .put_resv_regions = intel_iommu_put_resv_regions,
+ .put_resv_regions = iommu_put_resv_regions_simple,
.apply_resv_region = intel_iommu_apply_resv_region,
.device_group = pci_device_group,
.dev_has_feat = intel_iommu_dev_has_feat,
--
2.22.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
* [PATCH 3/5] iommu: amd: Use iommu_put_resv_regions_simple()
From: Thierry Reding @ 2019-08-29 11:17 UTC (permalink / raw)
To: Joerg Roedel
Cc: Jean-Philippe Brucker, Will Deacon, linux-kernel, virtualization,
iommu, Robin Murphy, David Woodhouse, linux-arm-kernel
In-Reply-To: <20190829111752.17513-1-thierry.reding@gmail.com>
From: Thierry Reding <treding@nvidia.com>
Use the new standard function instead of open-coding it.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
drivers/iommu/amd_iommu.c | 11 +----------
1 file changed, 1 insertion(+), 10 deletions(-)
diff --git a/drivers/iommu/amd_iommu.c b/drivers/iommu/amd_iommu.c
index 04a9f8443344..7d8896d5fab9 100644
--- a/drivers/iommu/amd_iommu.c
+++ b/drivers/iommu/amd_iommu.c
@@ -3160,15 +3160,6 @@ static void amd_iommu_get_resv_regions(struct device *dev,
list_add_tail(®ion->list, head);
}
-static void amd_iommu_put_resv_regions(struct device *dev,
- struct list_head *head)
-{
- struct iommu_resv_region *entry, *next;
-
- list_for_each_entry_safe(entry, next, head, list)
- kfree(entry);
-}
-
static void amd_iommu_apply_resv_region(struct device *dev,
struct iommu_domain *domain,
struct iommu_resv_region *region)
@@ -3216,7 +3207,7 @@ const struct iommu_ops amd_iommu_ops = {
.remove_device = amd_iommu_remove_device,
.device_group = amd_iommu_device_group,
.get_resv_regions = amd_iommu_get_resv_regions,
- .put_resv_regions = amd_iommu_put_resv_regions,
+ .put_resv_regions = iommu_put_resv_regions_simple,
.apply_resv_region = amd_iommu_apply_resv_region,
.is_attach_deferred = amd_iommu_is_attach_deferred,
.pgsize_bitmap = AMD_IOMMU_PGSIZES,
--
2.22.0
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox