* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Yury Norov @ 2026-06-21 13:39 UTC (permalink / raw)
To: Steven Rostedt
Cc: linux-kernel, linux-trace-kernel, Masami Hiramatsu, Mark Rutland,
Mathieu Desnoyers, Andrew Morton, Linus Torvalds,
Sebastian Andrzej Siewior, John Ogness, Thomas Gleixner,
Peter Zijlstra, Julia Lawall, Yury Norov, linux-doc, linux-kbuild,
linuxppc-dev, dri-devel, linux-stm32, linux-arm-kernel,
linux-rdma, linux-usb, linux-ext4, linux-nfs, kvm, intel-gfx
In-Reply-To: <20260621054721.7cde38f0@fedora>
On Sun, Jun 21, 2026 at 05:47:21AM -0400, Steven Rostedt wrote:
> On Sun, 21 Jun 2026 05:34:32 -0400
> Steven Rostedt <rostedt@kernel.org> wrote:
>
> > Instead of having trace_printk.h included in kernel.h, create a config
> > TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
> > Makefile to allow developers to add trace_printk() without the need to add
> > the include for it. Having it included in the Makefile keeps it from being
> > in the dependency chain and it will not waste extra CPU cycles for those
> > building the kernel without using trace_printk.
>
> Bah, I only tested with the config option enabled, and missed some
> dependencies with it disabled.
Yes you did.
> For instance, rcu.h also uses ftrace_dump() so that too needs to go
> into kernel.h.
No, it shouldn't.
> I also need to add a few more includes to trace_printk.h.
> OK, I need to run this through all my tests to find where else I missed
> adding the includes. But the idea should hopefully satisfy everyone.
If you include it under config in kernel.h, to make the kernel buildable,
you need to include trace_printk.h explicitly where it's actually used.
IOW, apply my patch v4-7.
Then, developers who use trace_printk() on their development machine,
will be really frustrated when their debugging code will break client
build just because CONFIG_TRACE_PRINTK_DEBUGGING is disabled there.
They will spend a day, at best, communicating with remote managers,
and end up with adding #include <linux/trace_printk.h> in the files
they touch. Is that your plan?
If I was one of those developers, the solution would be simple for me:
don't use trace_printk() at all.
Thanks,
Yury
^ permalink raw reply
* Re: [PATCH] wifi: mt76: mt7915: guard HE capability lookups
From: Lorenzo Bianconi @ 2026-06-21 13:32 UTC (permalink / raw)
To: Ruoyu Wang
Cc: Felix Fietkau, Ryder Lee, Shayne Chen, Sean Wang,
Matthias Brugger, AngeloGioacchino Del Regno, linux-wireless,
linux-kernel, linux-arm-kernel, linux-mediatek
In-Reply-To: <20260620155332.81120-1-ruoyuw560@gmail.com>
[-- Attachment #1: Type: text/plain, Size: 3281 bytes --]
> mt7915_mcu_bss_he_tlv() and mt7915_mcu_sta_bfer_tlv() both run after
> checking HE support, then dereference the HE PHY capability returned by
> mt76_connac_get_he_phy_cap(). That helper can return NULL when no
> capability entry matches the vif type.
>
> Fetch the capability before appending the TLV and skip the HE-specific
> setup when no matching capability is available.
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
>
> Fixes: e6d557a78b60 ("mt76: mt7915: rely on mt76_connac_get_phy utilities")
> Signed-off-by: Ruoyu Wang <ruoyuw560@gmail.com>
> ---
> .../net/wireless/mediatek/mt76/mt7915/mcu.c | 18 +++++++++++++-----
> 1 file changed, 13 insertions(+), 5 deletions(-)
>
> diff --git a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
> index 318c38149463..391c91675130 100644
> --- a/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
> +++ b/drivers/net/wireless/mediatek/mt76/mt7915/mcu.c
> @@ -595,6 +595,8 @@ mt7915_mcu_bss_he_tlv(struct sk_buff *skb, struct ieee80211_vif *vif,
> struct tlv *tlv;
>
> cap = mt76_connac_get_he_phy_cap(phy->mt76, vif);
> + if (!cap)
> + return;
>
> tlv = mt76_connac_mcu_add_tlv(skb, BSS_INFO_HE_BASIC, sizeof(*he));
>
> @@ -1177,13 +1179,12 @@ mt7915_mcu_sta_bfer_vht(struct ieee80211_sta *sta, struct mt7915_phy *phy,
> }
>
> static void
> -mt7915_mcu_sta_bfer_he(struct ieee80211_sta *sta, struct ieee80211_vif *vif,
> - struct mt7915_phy *phy, struct sta_rec_bf *bf)
> +mt7915_mcu_sta_bfer_he(struct ieee80211_sta *sta,
> + const struct ieee80211_sta_he_cap *vc,
> + struct sta_rec_bf *bf)
> {
> struct ieee80211_sta_he_cap *pc = &sta->deflink.he_cap;
> struct ieee80211_he_cap_elem *pe = &pc->he_cap_elem;
> - const struct ieee80211_sta_he_cap *vc =
> - mt76_connac_get_he_phy_cap(phy->mt76, vif);
> const struct ieee80211_he_cap_elem *ve = &vc->he_cap_elem;
> u16 mcs_map = le16_to_cpu(pc->he_mcs_nss_supp.rx_mcs_80);
> u8 nss_mcs = mt7915_mcu_get_sta_nss(mcs_map);
> @@ -1242,6 +1243,7 @@ mt7915_mcu_sta_bfer_tlv(struct mt7915_dev *dev, struct sk_buff *skb,
> {
> struct mt7915_vif *mvif = (struct mt7915_vif *)vif->drv_priv;
> struct mt7915_phy *phy = mvif->phy;
> + const struct ieee80211_sta_he_cap *vc = NULL;
> int tx_ant = hweight8(phy->mt76->chainmask) - 1;
> struct sta_rec_bf *bf;
> struct tlv *tlv;
> @@ -1260,6 +1262,12 @@ mt7915_mcu_sta_bfer_tlv(struct mt7915_dev *dev, struct sk_buff *skb,
> if (!ebf && !dev->ibf)
> return;
>
> + if (sta->deflink.he_cap.has_he && ebf) {
> + vc = mt76_connac_get_he_phy_cap(phy->mt76, vif);
> + if (!vc)
> + return;
> + }
> +
> tlv = mt76_connac_mcu_add_tlv(skb, STA_REC_BF, sizeof(*bf));
> bf = (struct sta_rec_bf *)tlv;
>
> @@ -1268,7 +1276,7 @@ mt7915_mcu_sta_bfer_tlv(struct mt7915_dev *dev, struct sk_buff *skb,
> * ht: iBF only, since mac80211 lacks of eBF support
> */
> if (sta->deflink.he_cap.has_he && ebf)
> - mt7915_mcu_sta_bfer_he(sta, vif, phy, bf);
> + mt7915_mcu_sta_bfer_he(sta, vc, bf);
> else if (sta->deflink.vht_cap.vht_supported)
> mt7915_mcu_sta_bfer_vht(sta, phy, bf, ebf);
> else if (sta->deflink.ht_cap.ht_supported)
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]
^ permalink raw reply
* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Yury Norov @ 2026-06-21 13:57 UTC (permalink / raw)
To: Yury Norov
Cc: Steven Rostedt, linux-kernel, linux-trace-kernel,
Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Thomas Gleixner, Peter Zijlstra, Julia Lawall, linux-doc,
linux-kbuild, linuxppc-dev, dri-devel, linux-stm32,
linux-arm-kernel, linux-rdma, linux-usb, linux-ext4, linux-nfs,
kvm, intel-gfx
In-Reply-To: <ajfphe4Z8BrfYoUX@yury>
On Sun, Jun 21, 2026 at 09:39:17AM -0400, Yury Norov wrote:
> On Sun, Jun 21, 2026 at 05:47:21AM -0400, Steven Rostedt wrote:
> > On Sun, 21 Jun 2026 05:34:32 -0400
> > Steven Rostedt <rostedt@kernel.org> wrote:
> >
> > > Instead of having trace_printk.h included in kernel.h, create a config
> > > TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
> > > Makefile to allow developers to add trace_printk() without the need to add
> > > the include for it. Having it included in the Makefile keeps it from being
> > > in the dependency chain and it will not waste extra CPU cycles for those
> > > building the kernel without using trace_printk.
> >
> > Bah, I only tested with the config option enabled, and missed some
> > dependencies with it disabled.
>
> Yes you did.
>
> > For instance, rcu.h also uses ftrace_dump() so that too needs to go
> > into kernel.h.
>
> No, it shouldn't.
>
> > I also need to add a few more includes to trace_printk.h.
>
> > OK, I need to run this through all my tests to find where else I missed
> > adding the includes. But the idea should hopefully satisfy everyone.
>
> If you include it under config in kernel.h, to make the kernel buildable,
I mean: in kernel.h or in Makefile.
> you need to include trace_printk.h explicitly where it's actually used.
> IOW, apply my patch v4-7.
>
> Then, developers who use trace_printk() on their development machine,
> will be really frustrated when their debugging code will break client
> build just because CONFIG_TRACE_PRINTK_DEBUGGING is disabled there.
> They will spend a day, at best, communicating with remote managers,
> and end up with adding #include <linux/trace_printk.h> in the files
> they touch. Is that your plan?
>
> If I was one of those developers, the solution would be simple for me:
> don't use trace_printk() at all.
>
> Thanks,
> Yury
^ permalink raw reply
* [PATCH 4/4] wifi: mt76: mt7996: fix possible NULL-pointer deref in mt7996_mcu_sta_bfer_eht()
From: Lorenzo Bianconi @ 2026-06-21 13:25 UTC (permalink / raw)
To: Felix Fietkau, Ryder Lee, Shayne Chen, Sean Wang,
Matthias Brugger, AngeloGioacchino Del Regno, Leon Yen, Hao Zhang,
Nelson Yu, Rong Yan, Money Wang, Bo Jiao, StanleyYP Wang,
Howard Hsu, Evelyn Tsai, Lorenzo Bianconi, Mingyen Hsieh
Cc: linux-wireless, linux-arm-kernel, linux-mediatek, Quan Zhou,
Deren Wu, MeiChia Chiu
In-Reply-To: <20260621-mt76_connac_get_he_phy_cap-fix-v1-0-ed4ccf7a0363@kernel.org>
mt76_connac_get_eht_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it.
Fixes: ba01944adee9f ("wifi: mt76: mt7996: add EHT beamforming support")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
---
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c | 9 +++++++--
1 file changed, 7 insertions(+), 2 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c
index c868b1356894..063097fad825 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c
@@ -1924,14 +1924,19 @@ mt7996_mcu_sta_bfer_eht(struct ieee80211_link_sta *link_sta,
struct ieee80211_sta_eht_cap *pc = &link_sta->eht_cap;
struct ieee80211_eht_cap_elem_fixed *pe = &pc->eht_cap_elem;
struct ieee80211_eht_mcs_nss_supp *eht_nss = &pc->eht_mcs_nss_supp;
- const struct ieee80211_sta_eht_cap *vc =
mt76_connac_get_eht_phy_cap(phy->mt76, vif);
- const struct ieee80211_eht_cap_elem_fixed *ve = &vc->eht_cap_elem;
u8 nss_mcs = u8_get_bits(eht_nss->bw._80.rx_tx_mcs9_max_nss,
IEEE80211_EHT_MCS_NSS_RX) - 1;
+ const struct ieee80211_eht_cap_elem_fixed *ve;
+ const struct ieee80211_sta_eht_cap *vc;
u8 snd_dim, sts;
+ vc = mt76_connac_get_eht_phy_cap(phy->mt76, vif);
+ if (!vc)
+ return;
+
bf->tx_mode = MT_PHY_TYPE_EHT_MU;
+ ve = &vc->eht_cap_elem;
mt7996_mcu_sta_sounding_rate(bf, phy);
--
2.54.0
^ permalink raw reply related
* [PATCH 2/4] wifi: mt76: mt7925: fix possible NULL-pointer deref in mt7925_mcu_bss_he_tlv()
From: Lorenzo Bianconi @ 2026-06-21 13:25 UTC (permalink / raw)
To: Felix Fietkau, Ryder Lee, Shayne Chen, Sean Wang,
Matthias Brugger, AngeloGioacchino Del Regno, Leon Yen, Hao Zhang,
Nelson Yu, Rong Yan, Money Wang, Bo Jiao, StanleyYP Wang,
Howard Hsu, Evelyn Tsai, Lorenzo Bianconi, Mingyen Hsieh
Cc: linux-wireless, linux-arm-kernel, linux-mediatek, Quan Zhou,
Deren Wu, MeiChia Chiu
In-Reply-To: <20260621-mt76_connac_get_he_phy_cap-fix-v1-0-ed4ccf7a0363@kernel.org>
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it.
Fixes: c948b5da6bbec ("wifi: mt76: mt7925: add Mediatek Wi-Fi7 driver for mt7925 chips")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
---
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c | 2 ++
1 file changed, 2 insertions(+)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
index e94fa544ff20..cb265a6fc7ad 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7925/mcu.c
@@ -2773,6 +2773,8 @@ mt7925_mcu_bss_he_tlv(struct sk_buff *skb, struct ieee80211_bss_conf *link_conf,
struct tlv *tlv;
cap = mt76_connac_get_he_phy_cap(phy->mt76, link_conf->vif);
+ if (!cap)
+ return;
tlv = mt76_connac_mcu_add_tlv(skb, UNI_BSS_INFO_HE_BASIC, sizeof(*he));
--
2.54.0
^ permalink raw reply related
* [PATCH 3/4] wifi: mt76: mt7996: check pointer returned by mt76_connac_get_he_phy_cap()
From: Lorenzo Bianconi @ 2026-06-21 13:25 UTC (permalink / raw)
To: Felix Fietkau, Ryder Lee, Shayne Chen, Sean Wang,
Matthias Brugger, AngeloGioacchino Del Regno, Leon Yen, Hao Zhang,
Nelson Yu, Rong Yan, Money Wang, Bo Jiao, StanleyYP Wang,
Howard Hsu, Evelyn Tsai, Lorenzo Bianconi, Mingyen Hsieh
Cc: linux-wireless, linux-arm-kernel, linux-mediatek, Quan Zhou,
Deren Wu, MeiChia Chiu
In-Reply-To: <20260621-mt76_connac_get_he_phy_cap-fix-v1-0-ed4ccf7a0363@kernel.org>
mt76_connac_get_he_phy_cap routine can theoretically return NULL so
check cap pointer before dereferencing it.
Fixes: 98686cd21624c ("wifi: mt76: mt7996: add driver for MediaTek Wi-Fi 7 (802.11be) devices")
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
---
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c | 9 ++++++---
1 file changed, 6 insertions(+), 3 deletions(-)
diff --git a/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c b/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c
index f119f023bcd5..c868b1356894 100644
--- a/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c
+++ b/drivers/net/wireless/mediatek/mt76/mt7996/mcu.c
@@ -935,6 +935,8 @@ mt7996_mcu_bss_he_tlv(struct sk_buff *skb, struct ieee80211_vif *vif,
struct tlv *tlv;
cap = mt76_connac_get_he_phy_cap(phy->mt76, vif);
+ if (!cap)
+ return;
tlv = mt7996_mcu_add_uni_tlv(skb, UNI_BSS_INFO_HE_BASIC, sizeof(*he));
@@ -1855,17 +1857,18 @@ mt7996_mcu_sta_bfer_he(struct ieee80211_link_sta *link_sta,
{
struct ieee80211_sta_he_cap *pc = &link_sta->he_cap;
struct ieee80211_he_cap_elem *pe = &pc->he_cap_elem;
- const struct ieee80211_sta_he_cap *vc =
- mt76_connac_get_he_phy_cap(phy->mt76, vif);
- const struct ieee80211_he_cap_elem *ve = &vc->he_cap_elem;
u16 mcs_map = le16_to_cpu(pc->he_mcs_nss_supp.rx_mcs_80);
u8 nss_mcs = mt7996_mcu_get_sta_nss(mcs_map);
+ const struct ieee80211_he_cap_elem *ve;
+ const struct ieee80211_sta_he_cap *vc;
u8 snd_dim, sts;
+ vc = mt76_connac_get_he_phy_cap(phy->mt76, vif);
if (!vc)
return;
bf->tx_mode = MT_PHY_TYPE_HE_SU;
+ ve = &vc->he_cap_elem;
mt7996_mcu_sta_sounding_rate(bf, phy);
--
2.54.0
^ permalink raw reply related
* [PATCH 0/4] wifi: mt76: fix some possible NULL-pointer dereferences
From: Lorenzo Bianconi @ 2026-06-21 13:24 UTC (permalink / raw)
To: Felix Fietkau, Ryder Lee, Shayne Chen, Sean Wang,
Matthias Brugger, AngeloGioacchino Del Regno, Leon Yen, Hao Zhang,
Nelson Yu, Rong Yan, Money Wang, Bo Jiao, StanleyYP Wang,
Howard Hsu, Evelyn Tsai, Lorenzo Bianconi, Mingyen Hsieh
Cc: linux-wireless, linux-arm-kernel, linux-mediatek, Quan Zhou,
Deren Wu, MeiChia Chiu
---
Lorenzo Bianconi (4):
wifi: mt76: connac: fix possible NULL-pointer deref in mt76_connac_mcu_uni_bss_he_tlv()
wifi: mt76: mt7925: fix possible NULL-pointer deref in mt7925_mcu_bss_he_tlv()
wifi: mt76: mt7996: check pointer returned by mt76_connac_get_he_phy_cap()
wifi: mt76: mt7996: fix possible NULL-pointer deref in mt7996_mcu_sta_bfer_eht()
drivers/net/wireless/mediatek/mt76/mt76_connac_mcu.c | 2 ++
drivers/net/wireless/mediatek/mt76/mt7925/mcu.c | 2 ++
drivers/net/wireless/mediatek/mt76/mt7996/mcu.c | 18 +++++++++++++-----
3 files changed, 17 insertions(+), 5 deletions(-)
---
base-commit: 50a7f9f9d48eb50c0e95bef53358acb5af5cb3c6
change-id: 20260621-mt76_connac_get_he_phy_cap-fix-2b3068d4d074
Best regards,
--
Lorenzo Bianconi <lorenzo@kernel.org>
^ permalink raw reply
* Re: [PATCH 1/2] tracing: Move non-trace_printk prototypes back to kernel.h
From: Yury Norov @ 2026-06-21 13:08 UTC (permalink / raw)
To: Steven Rostedt
Cc: linux-kernel, linux-trace-kernel, Masami Hiramatsu, Mark Rutland,
Mathieu Desnoyers, Andrew Morton, Linus Torvalds,
Sebastian Andrzej Siewior, John Ogness, Thomas Gleixner,
Peter Zijlstra, Julia Lawall, Yury Norov, linux-doc, linux-kbuild,
linuxppc-dev, dri-devel, linux-stm32, linux-arm-kernel,
linux-rdma, linux-usb, linux-ext4, linux-nfs, kvm, intel-gfx
In-Reply-To: <20260621093811.007634476@kernel.org>
On Sun, Jun 21, 2026 at 05:34:31AM -0400, Steven Rostedt wrote:
> From: Steven Rostedt <rostedt@goodmis.org>
>
> In order to remove the include to trace_printk.h from kernel.h the tracing
> control prototypes need to be moved back into kernel.h. That's because
Please don't. Instead, you can split them out to trace_control.h, and
include where needed. I actually have a prototype for it, FYI:
https://github.com/norov/linux/tree/trace_pritk3
> they are used in other common header files like rcu.h. There's no point in
> removing trace_printk.h from kernel.h if it just gets added back to other
> common headers.
>
> Prototypes are very cheap for the compiler and should not be an issue.
It's not about cost, it's about mess. kernel.h is included everywhere.
Is that API needed everywhere? No, it's needed in literally 10 files.
So, no place in kernel.h.
> Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
> ---
> include/linux/kernel.h | 18 ++++++++++++++++++
> include/linux/trace_printk.h | 17 -----------------
> 2 files changed, 18 insertions(+), 17 deletions(-)
>
> diff --git a/include/linux/kernel.h b/include/linux/kernel.h
> index e5570a16cbb1..c3c68128827c 100644
> --- a/include/linux/kernel.h
> +++ b/include/linux/kernel.h
> @@ -194,4 +194,22 @@ extern enum system_states system_state;
> # define REBUILD_DUE_TO_DYNAMIC_FTRACE
> #endif
>
> +#ifdef CONFIG_TRACING
> +void tracing_on(void);
> +void tracing_off(void);
> +int tracing_is_on(void);
> +void tracing_snapshot(void);
> +void tracing_snapshot_alloc(void);
> +void tracing_start(void);
> +void tracing_stop(void);
> +#else
> +static inline void tracing_start(void) { }
> +static inline void tracing_stop(void) { }
> +static inline void tracing_on(void) { }
> +static inline void tracing_off(void) { }
> +static inline int tracing_is_on(void) { return 0; }
> +static inline void tracing_snapshot(void) { }
> +static inline void tracing_snapshot_alloc(void) { }
> +#endif
> +
> #endif
> diff --git a/include/linux/trace_printk.h b/include/linux/trace_printk.h
> index 3d54f440dccf..879fed0805fd 100644
> --- a/include/linux/trace_printk.h
> +++ b/include/linux/trace_printk.h
> @@ -35,15 +35,6 @@ enum ftrace_dump_mode {
> };
>
> #ifdef CONFIG_TRACING
> -void tracing_on(void);
> -void tracing_off(void);
> -int tracing_is_on(void);
> -void tracing_snapshot(void);
> -void tracing_snapshot_alloc(void);
> -
> -extern void tracing_start(void);
> -extern void tracing_stop(void);
> -
> static inline __printf(1, 2)
> void ____trace_printk_check_format(const char *fmt, ...)
> {
> @@ -176,16 +167,8 @@ __ftrace_vprintk(unsigned long ip, const char *fmt, va_list ap);
>
> extern void ftrace_dump(enum ftrace_dump_mode oops_dump_mode);
> #else
> -static inline void tracing_start(void) { }
> -static inline void tracing_stop(void) { }
> static inline void trace_dump_stack(int skip) { }
>
> -static inline void tracing_on(void) { }
> -static inline void tracing_off(void) { }
> -static inline int tracing_is_on(void) { return 0; }
> -static inline void tracing_snapshot(void) { }
> -static inline void tracing_snapshot_alloc(void) { }
> -
> static inline __printf(1, 2)
> int trace_printk(const char *fmt, ...)
> {
> --
> 2.53.0
>
^ permalink raw reply
* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Steven Rostedt @ 2026-06-21 13:03 UTC (permalink / raw)
To: David Laight
Cc: Thomas Gleixner, linux-kernel, linux-trace-kernel,
Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Peter Zijlstra, Julia Lawall, Yury Norov, linux-doc, linux-kbuild,
linuxppc-dev, dri-devel, linux-stm32, linux-arm-kernel,
linux-rdma, linux-usb, linux-ext4, linux-nfs, kvm, intel-gfx
In-Reply-To: <20260621135531.243375d9@pumpkin>
On Sun, 21 Jun 2026 13:55:31 +0100
David Laight <david.laight.linux@gmail.com> wrote:
> Indeed...
> Isn't trace_printk() just an extern?
> Having it defined somewhere isn't going to make any difference to build times.
No it is not. It is a macro to cut as many nanoseconds as possible as
trace_printk() was created to debug tight race conditions and any added
latency can make the race go away.
-- Steve
^ permalink raw reply
* Re: [PATCH v5 09/10] iio: dac: add mcf54415 DAC
From: Jonathan Cameron @ 2026-06-21 12:55 UTC (permalink / raw)
To: Angelo Dureghello
Cc: Greg Ungerer, Geert Uytterhoeven, Steven King, Arnd Bergmann,
Maxime Coquelin, Alexandre Torgue, David Lechner, Nuno Sá,
Andy Shevchenko, Greg Ungerer, linux-m68k, linux-kernel,
linux-stm32, linux-arm-kernel, linux-iio, Michael Turquette,
Stephen Boyd, Brian Masney
In-Reply-To: <CALSJ-wC9Rsq6WJ_=X87R74jPrg2Y+=L8m0wRRp=1zvN5vSOw6A@mail.gmail.com>
On Mon, 15 Jun 2026 20:20:21 +0900
Angelo Dureghello <adureghello@baylibre.com> wrote:
> Hi Jonathan,
>
> On Thu, Jun 11, 2026 at 11:48:00AM +0100, Jonathan Cameron wrote:
> > On Wed, 10 Jun 2026 22:35:14 +0200
> > Angelo Dureghello <adureghello@baylibre.com> wrote:
> >
> > > From: Angelo Dureghello <adureghello@baylibre.com>
> > >
> > > Add basic version of mcf54415 DAC driver. DAC is embedded in the SoC and
> > > DAC configuration registers are mapped in the internal IO address space.
> > >
> > > The DAC accepts a 12-bit digital signal and creates a monotonic 12-bit
> > > analog output varying from DAC_VREFL to DAC_VREFH. The DAC module
> > > consists of a conversion unit, an output amplifier, and the associated
> > > digital control blocks. Default register values for DAC_VREFL and DAC_VREFH
> > > are respectively 0 and 0xfff, left untouched in this initial version.
> > >
> > > This initial version of the driver is minimalistic, "output raw" only, to
> > > be extended in the future. DMA and external sync are disabled, default mode
> > > is high speed, default format is right-justified 12-bit on 16-bit word.
> > >
> > > Signed-off-by: Angelo Dureghello <adureghello@baylibre.com>
> > I'm lazy so didn't check earlier versions but assume the two bits
> > of feedback from Sashiko are false positives:
> > https://sashiko.dev/#/patchset/20260610-wip-stmark2-dac-v5-0-b76b83366d5c%40baylibre.com
> >
> > The one about clock underflow if resume fails, and then devm cleanup happens later
> > is a bit nasty.
> >
> > I did a bit of digging and maybe it is better to just leave the clock on?
> > The status dev.power.is_suspended is set to false whether or not resume succeeded
> > and I believe a following suspend will not take into account that resume failed.
> >
> > I'm not set up to poke the combinations but it might be worth trying that.
> > +CC common clk people who may immediately know what the right answer is.
> >
>
> was about testing this, there are no bus faults on read/write of registers
> with clock disabled, nor warnings in dmesg on double disable.
Great. That makes life easier. I'm curious to why we don't get a double disable
though... Guess I'm missing something in the flows.
>
> Anyway, i see now from arch Kconfig that is not possible to have CONFIG_PM
> for this specifig CPU (with MMU, PM is force-disabled), so would remove pm_ops.
> Ok ?
I suspect that's something that might get 'fixed' at somepoint, so I'd keep
the PM stuff in this driver as long as you can check it basically works.
Jonathan
>
> Will fix all other things you pointyed out in v6.
>
> > Otherwise just a few minor style comments inline.
> >
> > Thanks,
> >
> > Jonathan
> >
>
> thanks,
> regards,
> angelo
>
^ permalink raw reply
* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: David Laight @ 2026-06-21 12:55 UTC (permalink / raw)
To: Thomas Gleixner
Cc: Steven Rostedt, linux-kernel, linux-trace-kernel,
Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Peter Zijlstra, Julia Lawall, Yury Norov, linux-doc, linux-kbuild,
linuxppc-dev, dri-devel, linux-stm32, linux-arm-kernel,
linux-rdma, linux-usb, linux-ext4, linux-nfs, kvm, intel-gfx
In-Reply-To: <87ik7cmcb7.ffs@fw13>
On Sun, 21 Jun 2026 12:13:00 +0200
Thomas Gleixner <tglx@kernel.org> wrote:
> On Sun, Jun 21 2026 at 05:34, Steven Rostedt wrote:
> > Instead of having trace_printk.h included in kernel.h, create a config
> > TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
> > Makefile to allow developers to add trace_printk() without the need to add
> > the include for it. Having it included in the Makefile keeps it from being
> > in the dependency chain and it will not waste extra CPU cycles for those
> > building the kernel without using trace_printk.
>
> IOW, you make it worse just because.
>
> With the header being separate I add the three trace_printk()s and the
> include to the source file I'm investigating. The recompile will build
> exactly this source file.
>
> Having to enable the config knob will result in a full kernel rebuild
> for no value.
Indeed...
Isn't trace_printk() just an extern?
Having it defined somewhere isn't going to make any difference to build times.
David
>
> Seriously?
>
> Thanks,
>
> tglx
>
>
>
^ permalink raw reply
* Re: [PATCH v2 3/4] irqchip/gic-v3: Add Renesas R-Car Gen4 erratum workaround
From: Thomas Gleixner @ 2026-06-21 10:59 UTC (permalink / raw)
To: Marek Vasut, linux-pci
Cc: Marek Vasut, Yoshihiro Shimoda, Krzysztof Wilczyński,
Bjorn Helgaas, Catalin Marinas, Conor Dooley, Geert Uytterhoeven,
Krzysztof Kozlowski, Lorenzo Pieralisi, Manivannan Sadhasivam,
Marc Zyngier, Rob Herring, devicetree, linux-arm-kernel,
linux-doc, linux-kernel, linux-renesas-soc
In-Reply-To: <20260618220427.14325-4-marek.vasut+renesas@mailbox.org>
On Fri, Jun 19 2026 at 00:02, Marek Vasut wrote:
> Renesas R-Car S4/V4H/V4M GIC600 integration has address width for AXI
> or APB interface configured to 32 bit, it can therefore access only
> the first 4 GiB of physical address space. This information comes from
> R-Car V4H Interface Specification sheet, there is currently no technical
> update number assigned to this limitation. Further input from hardware
> engineer indicates that this limitation also applies to R-Car S4 and V4M.
> Name the limitation GEN4GICITS1, and add a driver quirk to mitigate this
> limitation.
>
> The quirk is keyed on the combination of the GIC implementation
> and the platform identification in the device tree.
>
> Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
> Signed-off-by: Marek Vasut <marek.vasut+renesas@mailbox.org>
This SOB chain is broken.
^ permalink raw reply
* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Steven Rostedt @ 2026-06-21 10:38 UTC (permalink / raw)
To: Thomas Gleixner, Steven Rostedt, linux-kernel, linux-trace-kernel
Cc: Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Peter Zijlstra, Julia Lawall, Yury Norov, linux-doc, linux-kbuild,
linuxppc-dev, dri-devel, linux-stm32, linux-arm-kernel,
linux-rdma, linux-usb, linux-ext4, linux-nfs, kvm, intel-gfx
In-Reply-To: <87ik7cmcb7.ffs@fw13>
On June 21, 2026 11:13:00 AM GMT+01:00, Thomas Gleixner <tglx@kernel.org> wrote:
>On Sun, Jun 21 2026 at 05:34, Steven Rostedt wrote:
>> Instead of having trace_printk.h included in kernel.h, create a config
>> TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
>> Makefile to allow developers to add trace_printk() without the need to add
>> the include for it. Having it included in the Makefile keeps it from being
>> in the dependency chain and it will not waste extra CPU cycles for those
>> building the kernel without using trace_printk.
>
>IOW, you make it worse just because.
>
>With the header being separate I add the three trace_printk()s and the
>include to the source file I'm investigating. The recompile will build
>exactly this source file.
>
>Having to enable the config knob will result in a full kernel rebuild
>for no value.
>
>Seriously?
Like having lockdep enabled, this would always be set in the development environment. It's not something to only enable when you need to add a trace_printk. If you don't want to rebuild everything, by all means add the include file by file. There's nothing preventing you to do that with this solution.
-- Steve
P.S. I'm replying on my phone as I'm in the London Tube. Thus why I'm not trimming my email.
>
>Thanks,
>
> tglx
>
^ permalink raw reply
* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Thomas Gleixner @ 2026-06-21 10:13 UTC (permalink / raw)
To: Steven Rostedt, linux-kernel, linux-trace-kernel
Cc: Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Peter Zijlstra, Julia Lawall, Yury Norov, linux-doc, linux-kbuild,
linuxppc-dev, dri-devel, linux-stm32, linux-arm-kernel,
linux-rdma, linux-usb, linux-ext4, linux-nfs, kvm, intel-gfx
In-Reply-To: <20260621093811.168514984@kernel.org>
On Sun, Jun 21 2026 at 05:34, Steven Rostedt wrote:
> Instead of having trace_printk.h included in kernel.h, create a config
> TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
> Makefile to allow developers to add trace_printk() without the need to add
> the include for it. Having it included in the Makefile keeps it from being
> in the dependency chain and it will not waste extra CPU cycles for those
> building the kernel without using trace_printk.
IOW, you make it worse just because.
With the header being separate I add the three trace_printk()s and the
include to the source file I'm investigating. The recompile will build
exactly this source file.
Having to enable the config knob will result in a full kernel rebuild
for no value.
Seriously?
Thanks,
tglx
^ permalink raw reply
* Re: [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Steven Rostedt @ 2026-06-21 9:47 UTC (permalink / raw)
To: linux-kernel, linux-trace-kernel
Cc: Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Thomas Gleixner, Peter Zijlstra, Julia Lawall, Yury Norov,
linux-doc, linux-kbuild, linuxppc-dev, dri-devel, linux-stm32,
linux-arm-kernel, linux-rdma, linux-usb, linux-ext4, linux-nfs,
kvm, intel-gfx
In-Reply-To: <20260621093811.168514984@kernel.org>
On Sun, 21 Jun 2026 05:34:32 -0400
Steven Rostedt <rostedt@kernel.org> wrote:
> Instead of having trace_printk.h included in kernel.h, create a config
> TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
> Makefile to allow developers to add trace_printk() without the need to add
> the include for it. Having it included in the Makefile keeps it from being
> in the dependency chain and it will not waste extra CPU cycles for those
> building the kernel without using trace_printk.
Bah, I only tested with the config option enabled, and missed some
dependencies with it disabled.
For instance, rcu.h also uses ftrace_dump() so that too needs to go
into kernel.h. I also need to add a few more includes to trace_printk.h.
OK, I need to run this through all my tests to find where else I missed
adding the includes. But the idea should hopefully satisfy everyone.
-- Steve
^ permalink raw reply
* [PATCH 2/2] tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
From: Steven Rostedt @ 2026-06-21 9:34 UTC (permalink / raw)
To: linux-kernel, linux-trace-kernel
Cc: Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Thomas Gleixner, Peter Zijlstra, Julia Lawall, Yury Norov,
linux-doc, linux-kbuild, linuxppc-dev, dri-devel, linux-stm32,
linux-arm-kernel, linux-rdma, linux-usb, linux-ext4, linux-nfs,
kvm, intel-gfx
In-Reply-To: <20260621093430.264983361@kernel.org>
From: Steven Rostedt <rostedt@goodmis.org>
Instead of having trace_printk.h included in kernel.h, create a config
TRACE_PRINTK_DEBUGGING that when set will update the CFLAGS in the
Makefile to allow developers to add trace_printk() without the need to add
the include for it. Having it included in the Makefile keeps it from being
in the dependency chain and it will not waste extra CPU cycles for those
building the kernel without using trace_printk.
Link: https://lore.kernel.org/all/CAHk-=wikCBeVFjVXiY4o-oepdbjAoir5+TcAgtL12c4u1TpZLQ@mail.gmail.com/
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
.../debugging/driver_development_debugging_guide.rst | 2 +-
Makefile | 5 +++++
arch/powerpc/kvm/book3s_xics.c | 1 +
drivers/gpu/drm/i915/gt/intel_gtt.h | 1 +
drivers/gpu/drm/i915/i915_gem.h | 1 +
drivers/hwtracing/stm/dummy_stm.c | 4 ++++
drivers/infiniband/hw/hfi1/trace_dbg.h | 1 +
drivers/usb/early/xhci-dbc.c | 1 +
fs/ext4/inline.c | 1 +
include/linux/kernel.h | 1 -
include/linux/sunrpc/debug.h | 1 +
include/linux/trace_printk.h | 5 +++--
kernel/trace/Kconfig | 10 ++++++++++
kernel/trace/ring_buffer_benchmark.c | 1 +
kernel/trace/trace.h | 1 +
samples/fprobe/fprobe_example.c | 1 +
samples/ftrace/ftrace-direct-modify.c | 1 +
samples/ftrace/ftrace-direct-multi-modify.c | 1 +
samples/ftrace/ftrace-direct-multi.c | 2 +-
samples/ftrace/ftrace-direct-too.c | 2 +-
samples/ftrace/ftrace-direct.c | 2 +-
21 files changed, 38 insertions(+), 7 deletions(-)
diff --git a/Documentation/process/debugging/driver_development_debugging_guide.rst b/Documentation/process/debugging/driver_development_debugging_guide.rst
index aca08f457793..3c87aa03622f 100644
--- a/Documentation/process/debugging/driver_development_debugging_guide.rst
+++ b/Documentation/process/debugging/driver_development_debugging_guide.rst
@@ -52,7 +52,7 @@ For the full documentation see :doc:`/core-api/printk-basics`
Trace_printk
~~~~~~~~~~~~
-Prerequisite: ``CONFIG_DYNAMIC_FTRACE`` & ``#include <linux/ftrace.h>``
+Prerequisite: ``CONFIG_TRACE_PRINTK_DEBUGGING``
It is a tiny bit less comfortable to use than printk(), because you will have
to read the messages from the trace file (See: :ref:`read_ftrace_log`
diff --git a/Makefile b/Makefile
index d1c595db55c9..2f5923d5393b 100644
--- a/Makefile
+++ b/Makefile
@@ -840,6 +840,11 @@ ifdef CONFIG_FUNCTION_TRACER
CC_FLAGS_FTRACE := -pg
endif
+ifdef CONFIG_TRACE_PRINTK_DEBUGGING
+ # Allow trace_printk() to be used anywhere without including the header.
+ LINUXINCLUDE += -include $(srctree)/include/linux/trace_printk.h
+endif
+
ifdef CONFIG_TRACEPOINTS
# To check for unused tracepoints (tracepoints that are defined but never
# called), run with:
diff --git a/arch/powerpc/kvm/book3s_xics.c b/arch/powerpc/kvm/book3s_xics.c
index 74a44fa702b0..ef5eb596a56e 100644
--- a/arch/powerpc/kvm/book3s_xics.c
+++ b/arch/powerpc/kvm/book3s_xics.c
@@ -26,6 +26,7 @@
#if 1
#define XICS_DBG(fmt...) do { } while (0)
#else
+#include <linux/trace_printk.h>
#define XICS_DBG(fmt...) trace_printk(fmt)
#endif
diff --git a/drivers/gpu/drm/i915/gt/intel_gtt.h b/drivers/gpu/drm/i915/gt/intel_gtt.h
index b54ee4f25af1..f6f223090760 100644
--- a/drivers/gpu/drm/i915/gt/intel_gtt.h
+++ b/drivers/gpu/drm/i915/gt/intel_gtt.h
@@ -35,6 +35,7 @@
#define I915_GFP_ALLOW_FAIL (GFP_KERNEL | __GFP_RETRY_MAYFAIL | __GFP_NOWARN)
#if IS_ENABLED(CONFIG_DRM_I915_TRACE_GTT)
+#include <linux/trace_printk.h>
#define GTT_TRACE(...) trace_printk(__VA_ARGS__)
#else
#define GTT_TRACE(...)
diff --git a/drivers/gpu/drm/i915/i915_gem.h b/drivers/gpu/drm/i915/i915_gem.h
index 20b3cb29cfff..5cab1836dc1d 100644
--- a/drivers/gpu/drm/i915/i915_gem.h
+++ b/drivers/gpu/drm/i915/i915_gem.h
@@ -116,6 +116,7 @@ int i915_gem_open(struct drm_i915_private *i915, struct drm_file *file);
#endif
#if IS_ENABLED(CONFIG_DRM_I915_TRACE_GEM)
+#include <linux/trace_printk.h>
#define GEM_TRACE(...) trace_printk(__VA_ARGS__)
#define GEM_TRACE_ERR(...) do { \
pr_err(__VA_ARGS__); \
diff --git a/drivers/hwtracing/stm/dummy_stm.c b/drivers/hwtracing/stm/dummy_stm.c
index 38528ffdc0b3..784f9af7ccba 100644
--- a/drivers/hwtracing/stm/dummy_stm.c
+++ b/drivers/hwtracing/stm/dummy_stm.c
@@ -14,6 +14,10 @@
#include <linux/stm.h>
#include <uapi/linux/stm.h>
+#ifdef DEBUG
+#include <linux/trace_printk.h>
+#endif
+
static ssize_t notrace
dummy_stm_packet(struct stm_data *stm_data, unsigned int master,
unsigned int channel, unsigned int packet, unsigned int flags,
diff --git a/drivers/infiniband/hw/hfi1/trace_dbg.h b/drivers/infiniband/hw/hfi1/trace_dbg.h
index 58304b91380f..30df5e246586 100644
--- a/drivers/infiniband/hw/hfi1/trace_dbg.h
+++ b/drivers/infiniband/hw/hfi1/trace_dbg.h
@@ -103,6 +103,7 @@ __hfi1_trace_def(IOCTL);
*/
#ifdef HFI1_EARLY_DBG
+#include <linux/trace_printk.h>
#define hfi1_dbg_early(fmt, ...) \
trace_printk(fmt, ##__VA_ARGS__)
#else
diff --git a/drivers/usb/early/xhci-dbc.c b/drivers/usb/early/xhci-dbc.c
index 41118bba9197..955c73bd601f 100644
--- a/drivers/usb/early/xhci-dbc.c
+++ b/drivers/usb/early/xhci-dbc.c
@@ -30,6 +30,7 @@ static struct xdbc_state xdbc;
static bool early_console_keep;
#ifdef XDBC_TRACE
+#include <linux/trace_printk.h>
#define xdbc_trace trace_printk
#else
static inline void xdbc_trace(const char *fmt, ...) { }
diff --git a/fs/ext4/inline.c b/fs/ext4/inline.c
index 8045e4ff270c..0eff4a0c6a6c 100644
--- a/fs/ext4/inline.c
+++ b/fs/ext4/inline.c
@@ -934,6 +934,7 @@ static int ext4_da_convert_inline_data_to_extent(struct address_space *mapping,
}
#ifdef INLINE_DIR_DEBUG
+#include <linux/trace_printk.h>
void ext4_show_inline_dir(struct inode *dir, struct buffer_head *bh,
void *inline_start, int inline_size)
{
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index c3c68128827c..538655385089 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -31,7 +31,6 @@
#include <linux/build_bug.h>
#include <linux/sprintf.h>
#include <linux/static_call_types.h>
-#include <linux/trace_printk.h>
#include <linux/util_macros.h>
#include <linux/wordpart.h>
diff --git a/include/linux/sunrpc/debug.h b/include/linux/sunrpc/debug.h
index ab61bed2f7af..7524f5d82fba 100644
--- a/include/linux/sunrpc/debug.h
+++ b/include/linux/sunrpc/debug.h
@@ -29,6 +29,7 @@ extern unsigned int nlm_debug;
# define ifdebug(fac) if (unlikely(rpc_debug & RPCDBG_##fac))
# if IS_ENABLED(CONFIG_SUNRPC_DEBUG_TRACE)
+# include <linux/trace_printk.h>
# define __sunrpc_printk(fmt, ...) trace_printk(fmt, ##__VA_ARGS__)
# else
# define __sunrpc_printk(fmt, ...) printk(KERN_DEFAULT fmt, ##__VA_ARGS__)
diff --git a/include/linux/trace_printk.h b/include/linux/trace_printk.h
index 879fed0805fd..66edec6d5dbf 100644
--- a/include/linux/trace_printk.h
+++ b/include/linux/trace_printk.h
@@ -1,11 +1,12 @@
/* SPDX-License-Identifier: GPL-2.0 */
#ifndef _LINUX_TRACE_PRINTK_H
#define _LINUX_TRACE_PRINTK_H
+#if !defined(__ASSEMBLY__) && !defined(__GENKSYMS__) && !defined(BUILD_VDSO)
-#include <linux/compiler_attributes.h>
#include <linux/instruction_pointer.h>
#include <linux/stddef.h>
#include <linux/stringify.h>
+#include <linux/stdarg.h>
/*
* General tracing related utility functions - trace_printk(),
@@ -181,5 +182,5 @@ ftrace_vprintk(const char *fmt, va_list ap)
}
static inline void ftrace_dump(enum ftrace_dump_mode oops_dump_mode) { }
#endif /* CONFIG_TRACING */
-
+#endif /* !defined(__ASSEMBLY__) && !defined(__GENKSYMS__) */
#endif
diff --git a/kernel/trace/Kconfig b/kernel/trace/Kconfig
index 084f34dc6c9f..ffbd1b0ce66e 100644
--- a/kernel/trace/Kconfig
+++ b/kernel/trace/Kconfig
@@ -210,6 +210,16 @@ menuconfig FTRACE
if FTRACE
+config TRACE_PRINTK_DEBUGGING
+ bool "Debug with trace_printk()"
+ help
+ If you need to debug with trace_printk(), instead of adding
+ include <linux/trace_printk.h> to every file you add a trace_printk
+ to, select this option and it will add trace_printk.h to all code
+ to allow tracing with trace_printk() with.
+
+ If in doubt, select N
+
config TRACEFS_AUTOMOUNT_DEPRECATED
bool "Automount tracefs on debugfs [DEPRECATED]"
depends on TRACING
diff --git a/kernel/trace/ring_buffer_benchmark.c b/kernel/trace/ring_buffer_benchmark.c
index 593e3b59e42e..2bb25caebb75 100644
--- a/kernel/trace/ring_buffer_benchmark.c
+++ b/kernel/trace/ring_buffer_benchmark.c
@@ -5,6 +5,7 @@
* Copyright (C) 2009 Steven Rostedt <srostedt@redhat.com>
*/
#include <linux/ring_buffer.h>
+#include <linux/trace_printk.h>
#include <linux/completion.h>
#include <linux/kthread.h>
#include <uapi/linux/sched/types.h>
diff --git a/kernel/trace/trace.h b/kernel/trace/trace.h
index 80fe152af1dd..580a3deab1e9 100644
--- a/kernel/trace/trace.h
+++ b/kernel/trace/trace.h
@@ -13,6 +13,7 @@
#include <linux/ftrace.h>
#include <linux/trace.h>
#include <linux/hw_breakpoint.h>
+#include <linux/trace_printk.h>
#include <linux/trace_seq.h>
#include <linux/trace_events.h>
#include <linux/compiler.h>
diff --git a/samples/fprobe/fprobe_example.c b/samples/fprobe/fprobe_example.c
index bfe98ce826f3..de81b9b4ca7d 100644
--- a/samples/fprobe/fprobe_example.c
+++ b/samples/fprobe/fprobe_example.c
@@ -12,6 +12,7 @@
#define pr_fmt(fmt) "%s: " fmt, __func__
+#include <linux/trace_printk.h>
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/fprobe.h>
diff --git a/samples/ftrace/ftrace-direct-modify.c b/samples/ftrace/ftrace-direct-modify.c
index 1ba1927b548e..30d0f8e644c8 100644
--- a/samples/ftrace/ftrace-direct-modify.c
+++ b/samples/ftrace/ftrace-direct-modify.c
@@ -1,4 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/trace_printk.h>
#include <linux/module.h>
#include <linux/kthread.h>
#include <linux/ftrace.h>
diff --git a/samples/ftrace/ftrace-direct-multi-modify.c b/samples/ftrace/ftrace-direct-multi-modify.c
index 7a7822dfeb50..f64b929e19ec 100644
--- a/samples/ftrace/ftrace-direct-multi-modify.c
+++ b/samples/ftrace/ftrace-direct-multi-modify.c
@@ -1,4 +1,5 @@
// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/trace_printk.h>
#include <linux/module.h>
#include <linux/kthread.h>
#include <linux/ftrace.h>
diff --git a/samples/ftrace/ftrace-direct-multi.c b/samples/ftrace/ftrace-direct-multi.c
index 3fe6ddaf0b69..d32644a49554 100644
--- a/samples/ftrace/ftrace-direct-multi.c
+++ b/samples/ftrace/ftrace-direct-multi.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/trace_printk.h>
#include <linux/module.h>
-
#include <linux/mm.h> /* for handle_mm_fault() */
#include <linux/ftrace.h>
#include <linux/sched/stat.h>
diff --git a/samples/ftrace/ftrace-direct-too.c b/samples/ftrace/ftrace-direct-too.c
index bf2411aa6fd7..266fcb233301 100644
--- a/samples/ftrace/ftrace-direct-too.c
+++ b/samples/ftrace/ftrace-direct-too.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/trace_printk.h>
#include <linux/module.h>
-
#include <linux/mm.h> /* for handle_mm_fault() */
#include <linux/ftrace.h>
#if !defined(CONFIG_ARM64) && !defined(CONFIG_PPC32)
diff --git a/samples/ftrace/ftrace-direct.c b/samples/ftrace/ftrace-direct.c
index 5368c8c39cbb..85e0dff9b691 100644
--- a/samples/ftrace/ftrace-direct.c
+++ b/samples/ftrace/ftrace-direct.c
@@ -1,6 +1,6 @@
// SPDX-License-Identifier: GPL-2.0-only
+#include <linux/trace_printk.h>
#include <linux/module.h>
-
#include <linux/sched.h> /* for wake_up_process() */
#include <linux/ftrace.h>
#if !defined(CONFIG_ARM64) && !defined(CONFIG_PPC32)
--
2.53.0
^ permalink raw reply related
* [PATCH 1/2] tracing: Move non-trace_printk prototypes back to kernel.h
From: Steven Rostedt @ 2026-06-21 9:34 UTC (permalink / raw)
To: linux-kernel, linux-trace-kernel
Cc: Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Thomas Gleixner, Peter Zijlstra, Julia Lawall, Yury Norov,
linux-doc, linux-kbuild, linuxppc-dev, dri-devel, linux-stm32,
linux-arm-kernel, linux-rdma, linux-usb, linux-ext4, linux-nfs,
kvm, intel-gfx
In-Reply-To: <20260621093430.264983361@kernel.org>
From: Steven Rostedt <rostedt@goodmis.org>
In order to remove the include to trace_printk.h from kernel.h the tracing
control prototypes need to be moved back into kernel.h. That's because
they are used in other common header files like rcu.h. There's no point in
removing trace_printk.h from kernel.h if it just gets added back to other
common headers.
Prototypes are very cheap for the compiler and should not be an issue.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
---
include/linux/kernel.h | 18 ++++++++++++++++++
include/linux/trace_printk.h | 17 -----------------
2 files changed, 18 insertions(+), 17 deletions(-)
diff --git a/include/linux/kernel.h b/include/linux/kernel.h
index e5570a16cbb1..c3c68128827c 100644
--- a/include/linux/kernel.h
+++ b/include/linux/kernel.h
@@ -194,4 +194,22 @@ extern enum system_states system_state;
# define REBUILD_DUE_TO_DYNAMIC_FTRACE
#endif
+#ifdef CONFIG_TRACING
+void tracing_on(void);
+void tracing_off(void);
+int tracing_is_on(void);
+void tracing_snapshot(void);
+void tracing_snapshot_alloc(void);
+void tracing_start(void);
+void tracing_stop(void);
+#else
+static inline void tracing_start(void) { }
+static inline void tracing_stop(void) { }
+static inline void tracing_on(void) { }
+static inline void tracing_off(void) { }
+static inline int tracing_is_on(void) { return 0; }
+static inline void tracing_snapshot(void) { }
+static inline void tracing_snapshot_alloc(void) { }
+#endif
+
#endif
diff --git a/include/linux/trace_printk.h b/include/linux/trace_printk.h
index 3d54f440dccf..879fed0805fd 100644
--- a/include/linux/trace_printk.h
+++ b/include/linux/trace_printk.h
@@ -35,15 +35,6 @@ enum ftrace_dump_mode {
};
#ifdef CONFIG_TRACING
-void tracing_on(void);
-void tracing_off(void);
-int tracing_is_on(void);
-void tracing_snapshot(void);
-void tracing_snapshot_alloc(void);
-
-extern void tracing_start(void);
-extern void tracing_stop(void);
-
static inline __printf(1, 2)
void ____trace_printk_check_format(const char *fmt, ...)
{
@@ -176,16 +167,8 @@ __ftrace_vprintk(unsigned long ip, const char *fmt, va_list ap);
extern void ftrace_dump(enum ftrace_dump_mode oops_dump_mode);
#else
-static inline void tracing_start(void) { }
-static inline void tracing_stop(void) { }
static inline void trace_dump_stack(int skip) { }
-static inline void tracing_on(void) { }
-static inline void tracing_off(void) { }
-static inline int tracing_is_on(void) { return 0; }
-static inline void tracing_snapshot(void) { }
-static inline void tracing_snapshot_alloc(void) { }
-
static inline __printf(1, 2)
int trace_printk(const char *fmt, ...)
{
--
2.53.0
^ permalink raw reply related
* [PATCH 0/2] tracing: Move trace_printk.h out of kernel.h
From: Steven Rostedt @ 2026-06-21 9:34 UTC (permalink / raw)
To: linux-kernel, linux-trace-kernel
Cc: Masami Hiramatsu, Mark Rutland, Mathieu Desnoyers, Andrew Morton,
Linus Torvalds, Sebastian Andrzej Siewior, John Ogness,
Thomas Gleixner, Peter Zijlstra, Julia Lawall, Yury Norov,
linux-doc, linux-kbuild, linuxppc-dev, dri-devel, linux-stm32,
linux-arm-kernel, linux-rdma, linux-usb, linux-ext4, linux-nfs,
kvm, intel-gfx
There's been complaints about trace_printk() being defined in kernel.h as it
can increase the compilation time. As it is only used by some developers for
debugging purposes, it should not be in kernel.h causing lots of wasted CPU
cycles for those that do not ever care about it.
Instead, add a CONFIG_TRACE_PRINTK_DEBUGGING option that developers that do
use it can set and not have to always remember to add #include <linux/trace_printk.h>
to the files they add trace_printk() while debugging. It also means that
those that do not have that config set will not have to worry about wasted
CPU cycles as it is only include in the CFLAGS when the option is set, and
its completely ignored otherwise.
Steven Rostedt (2):
tracing: Move non-trace_printk prototypes back to kernel.h
tracing: Add CONFIG_TRACE_PRINTK_DEBUGGING to clean up kernel.h
----
.../driver_development_debugging_guide.rst | 2 +-
Makefile | 5 +++++
arch/powerpc/kvm/book3s_xics.c | 1 +
drivers/gpu/drm/i915/gt/intel_gtt.h | 1 +
drivers/gpu/drm/i915/i915_gem.h | 1 +
drivers/hwtracing/stm/dummy_stm.c | 4 ++++
drivers/infiniband/hw/hfi1/trace_dbg.h | 1 +
drivers/usb/early/xhci-dbc.c | 1 +
fs/ext4/inline.c | 1 +
include/linux/kernel.h | 19 ++++++++++++++++++-
include/linux/sunrpc/debug.h | 1 +
include/linux/trace_printk.h | 22 +++-------------------
kernel/trace/Kconfig | 10 ++++++++++
kernel/trace/ring_buffer_benchmark.c | 1 +
kernel/trace/trace.h | 1 +
samples/fprobe/fprobe_example.c | 1 +
samples/ftrace/ftrace-direct-modify.c | 1 +
samples/ftrace/ftrace-direct-multi-modify.c | 1 +
samples/ftrace/ftrace-direct-multi.c | 2 +-
samples/ftrace/ftrace-direct-too.c | 2 +-
samples/ftrace/ftrace-direct.c | 2 +-
21 files changed, 56 insertions(+), 24 deletions(-)
^ permalink raw reply
* [PATCH v9 9/9] arm64: dts: mediatek: Add MediaTek MT6392 PMIC dtsi
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Val Packett, Luca Leonardo Scorcia, Dmitry Torokhov, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sen Chu, Sean Wang,
Macpaul Lin, Lee Jones, Matthias Brugger,
AngeloGioacchino Del Regno, Liam Girdwood, Mark Brown,
Linus Walleij, Julien Massot, Louis-Alexis Eyraud, Fabien Parent,
Akari Tsuyukusa, Chen Zhong, linux-input, devicetree,
linux-kernel, linux-pm, linux-arm-kernel, linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
From: Val Packett <val@packett.cool>
Add the dtsi to be included by all boards using the MT6392 PMIC,
providing support for regulator, keys, pinctrl and RTC.
Import the new file in the shared device tree for the Pumpkin boards.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
---
arch/arm64/boot/dts/mediatek/mt6392.dtsi | 145 ++++++++++++++++++
.../boot/dts/mediatek/pumpkin-common.dtsi | 7 +
2 files changed, 152 insertions(+)
create mode 100644 arch/arm64/boot/dts/mediatek/mt6392.dtsi
diff --git a/arch/arm64/boot/dts/mediatek/mt6392.dtsi b/arch/arm64/boot/dts/mediatek/mt6392.dtsi
new file mode 100644
index 000000000000..69d63c153d9e
--- /dev/null
+++ b/arch/arm64/boot/dts/mediatek/mt6392.dtsi
@@ -0,0 +1,145 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019 MediaTek Inc.
+ * Copyright (c) 2024 Val Packett <val@packett.cool>
+ * Copyright (c) 2026 Luca Leonardo Scorcia <l.scorcia@gmail.com>
+ */
+
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/regulator/mediatek,mt6392-regulator.h>
+
+&pwrap {
+ pmic: pmic {
+ compatible = "mediatek,mt6392", "mediatek,mt6323";
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ mt6392keys: keys {
+ compatible = "mediatek,mt6392-keys";
+
+ key-power {
+ linux,keycodes = <KEY_POWER>;
+ wakeup-source;
+ };
+
+ key-home {
+ linux,keycodes = <KEY_HOME>;
+ wakeup-source;
+ };
+ };
+
+ mt6392pio: pinctrl {
+ compatible = "mediatek,mt6392-pinctrl";
+
+ gpio-controller;
+ #gpio-cells = <2>;
+ };
+
+ mt6392regulators: regulators {
+ compatible = "mediatek,mt6392-regulator";
+
+ /* Fixed supply defined in the data sheet */
+ avddldo-supply = <&mt6392_vsys_reg>;
+
+ mt6392_vcore_reg: vcore {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_BUCK_MODE_FORCE_PWM>;
+ };
+ mt6392_vproc_reg: vproc {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_BUCK_MODE_FORCE_PWM>;
+ };
+ mt6392_vsys_reg: vsys {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_BUCK_MODE_FORCE_PWM>;
+ };
+ mt6392_vaud28_reg: vaud28 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vxo22_reg: vxo22 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vaud22_reg: vaud22 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vadc18_reg: vadc18 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vcama_reg: vcama { };
+ mt6392_vcn35_reg: vcn35 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vio28_reg: vio28 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vusb_reg: vusb {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vmc_reg: vmc {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vmch_reg: vmch {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vemc3v3_reg: vemc3v3 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vcamaf_reg: vcamaf {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vgp1_reg: vgp1 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vgp2_reg: vgp2 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vefuse_reg: vefuse {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vm25_reg: vm25 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vdig18_reg: vdig18 { };
+ mt6392_vm_reg: vm {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vio18_reg: vio18 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vcn18_reg: vcn18 {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vcamd_reg: vcamd {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vcamio_reg: vcamio {
+ regulator-allowed-modes = <MT6392_REGULATOR_MODE_NORMAL
+ MT6392_LDO_MODE_LP>;
+ };
+ mt6392_vrtc_reg: vrtc { };
+ };
+
+ mt6392rtc: rtc {
+ compatible = "mediatek,mt6392-rtc", "mediatek,mt6323-rtc";
+ };
+ };
+};
diff --git a/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi b/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
index 805fb82138a8..b19d5792bd89 100644
--- a/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
+++ b/arch/arm64/boot/dts/mediatek/pumpkin-common.dtsi
@@ -6,6 +6,8 @@
#include <dt-bindings/gpio/gpio.h>
+#include "mt6392.dtsi"
+
/ {
aliases {
serial0 = &uart0;
@@ -160,6 +162,11 @@ &i2c2 {
status = "okay";
};
+&pmic {
+ interrupt-parent = <&pio>;
+ interrupts = <28 IRQ_TYPE_LEVEL_HIGH>;
+};
+
&uart0 {
status = "okay";
};
--
2.43.0
^ permalink raw reply related
* [PATCH v9 8/9] regulator: Add MediaTek MT6392 regulator
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Fabien Parent, Val Packett, Luca Leonardo Scorcia,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Sen Chu, Sean Wang, Macpaul Lin, Lee Jones, Matthias Brugger,
AngeloGioacchino Del Regno, Liam Girdwood, Mark Brown,
Linus Walleij, Louis-Alexis Eyraud, Julien Massot,
Akari Tsuyukusa, Chen Zhong, linux-input, devicetree,
linux-kernel, linux-pm, linux-arm-kernel, linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
From: Fabien Parent <parent.f@gmail.com>
The MT6392 is a regulator found on boards based on the MediaTek
MT8167, MT8516, and probably other SoCs. It is a so called PMIC and
connects as a slave to a SoC using SPI, wrapped inside PWRAP.
Signed-off-by: Fabien Parent <parent.f@gmail.com>
Co-developed-by: Val Packett <val@packett.cool>
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
---
drivers/regulator/Kconfig | 9 +
drivers/regulator/Makefile | 1 +
drivers/regulator/mt6392-regulator.c | 764 +++++++++++++++++++++
include/linux/regulator/mt6392-regulator.h | 42 ++
4 files changed, 816 insertions(+)
create mode 100644 drivers/regulator/mt6392-regulator.c
create mode 100644 include/linux/regulator/mt6392-regulator.h
diff --git a/drivers/regulator/Kconfig b/drivers/regulator/Kconfig
index a54a549196fe..ae375b9e6391 100644
--- a/drivers/regulator/Kconfig
+++ b/drivers/regulator/Kconfig
@@ -1001,6 +1001,15 @@ config REGULATOR_MT6380
This driver supports the control of different power rails of device
through regulator interface.
+config REGULATOR_MT6392
+ tristate "MediaTek MT6392 PMIC"
+ depends on MFD_MT6397
+ help
+ Say y here to select this option to enable the power regulator of
+ MediaTek MT6392 PMIC.
+ This driver supports the control of different power rails of device
+ through regulator interface.
+
config REGULATOR_MT6397
tristate "MediaTek MT6397 PMIC"
depends on MFD_MT6397
diff --git a/drivers/regulator/Makefile b/drivers/regulator/Makefile
index 134eee274dbf..a8e795a1eda1 100644
--- a/drivers/regulator/Makefile
+++ b/drivers/regulator/Makefile
@@ -118,6 +118,7 @@ obj-$(CONFIG_REGULATOR_MT6360) += mt6360-regulator.o
obj-$(CONFIG_REGULATOR_MT6363) += mt6363-regulator.o
obj-$(CONFIG_REGULATOR_MT6370) += mt6370-regulator.o
obj-$(CONFIG_REGULATOR_MT6380) += mt6380-regulator.o
+obj-$(CONFIG_REGULATOR_MT6392) += mt6392-regulator.o
obj-$(CONFIG_REGULATOR_MT6397) += mt6397-regulator.o
obj-$(CONFIG_REGULATOR_MTK_DVFSRC) += mtk-dvfsrc-regulator.o
obj-$(CONFIG_REGULATOR_QCOM_LABIBB) += qcom-labibb-regulator.o
diff --git a/drivers/regulator/mt6392-regulator.c b/drivers/regulator/mt6392-regulator.c
new file mode 100644
index 000000000000..93fe887709c3
--- /dev/null
+++ b/drivers/regulator/mt6392-regulator.c
@@ -0,0 +1,764 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2020 MediaTek Inc.
+ * Copyright (c) 2020 BayLibre, SAS.
+ * Author: Chen Zhong <chen.zhong@mediatek.com>
+ * Author: Fabien Parent <fparent@baylibre.com>
+ * Author: Luca Leonardo Scorcia <l.scorcia@gmail.com>
+ *
+ * The data sheet for MT6392 regulators is spotty to say the least,
+ * many important registers/fields are missing and the ones that aren't
+ * lack crucial information. Some useful details have been retrieved from
+ * Android sources.
+ * The driver code is mostly based on the MT6397 one.
+ */
+
+#include <linux/module.h>
+#include <linux/linear_range.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/mfd/mt6397/core.h>
+#include <linux/mfd/mt6392/registers.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/mt6392-regulator.h>
+#include <linux/regulator/of_regulator.h>
+
+/*
+ * Buck mode constants which may be used in devicetree properties (eg.
+ * regulator-initial-mode, regulator-allowed-modes).
+ * See the manufacturer's datasheet for more information on these modes.
+ */
+#define MT6392_REGULATOR_MODE_NORMAL 0
+#define MT6392_BUCK_MODE_FORCE_PWM 1
+
+/*
+ * LDO mode constants which may be used in devicetree properties (eg.
+ * regulator-initial-mode, regulator-allowed-modes).
+ * See the manufacturer's datasheet for more information on these modes.
+ */
+#define MT6392_LDO_MODE_LP 2
+
+/**
+ * MT6392 regulators' information
+ *
+ * @desc: standard fields of regulator description.
+ * @qi_status_reg: Register to query enable signal status of regulators
+ * @qi_status_mask: Mask to query enable signal status of regulators (RO)
+ * @vselctrl_reg: Vsel control mode selector register
+ * @vselctrl_mask: Vsel control mode selector mask (RO)
+ * @vsel_reg_mode_reg: Vsel register when Vsel control mode selector = 0 (Register mode)
+ * @vsel_reg_mode_mask: Vsel register mask in Register mode (RW)
+ * @vsel_normal_mode_reg: Vsel register when Vsel control mode selector = 1 (Normal mode)
+ * @vsel_normal_mode_mask: Vsel register mask in Register mode (RW)
+ * @pwm_modeset_reg: Register to control buck mode (Auto/Force PWM)
+ * @pwm_modeset_mask: Mask to control buck mode (RW)
+ * @lp_modeget_reg: Register to get LDO low-power mode
+ * @lp_modeget_mask: Mask to get LDO low-power mode (RO)
+ * @lp_modeset_reg: Register to control LDO low-power mode
+ * @lp_modeset_mask: Mask to control LDO low-power mode (WO)
+ */
+struct mt6392_regulator_info {
+ struct regulator_desc desc;
+ u32 qi_status_reg;
+ u32 qi_status_mask;
+ u32 vselctrl_reg;
+ u32 vselctrl_mask;
+ u32 vsel_reg_mode_reg;
+ u32 vsel_reg_mode_mask;
+ u32 vsel_normal_mode_reg;
+ u32 vsel_normal_mode_mask;
+ u32 pwm_modeset_reg;
+ u32 pwm_modeset_mask;
+ u32 lp_modeget_reg;
+ u32 lp_modeget_mask;
+ u32 lp_modeset_reg;
+ u32 lp_modeset_mask;
+};
+
+#define MT6392_BUCK(match, vreg, supply, min, max, step, volt_ranges, \
+ _qi_status_reg, _qi_status_mask, _enable_reg, _enable_mask, \
+ _vselctrl_reg, _vselctrl_mask, \
+ _vsel_reg_mode_reg, _vsel_reg_mode_mask, \
+ _vsel_normal_mode_reg, _vsel_normal_mode_mask, \
+ _pwm_modeset_reg, _pwm_modeset_mask, _ramp_delay) \
+[MT6392_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .supply_name = supply, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .ops = &mt6392_volt_range_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6392_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .linear_ranges = volt_ranges, \
+ .n_linear_ranges = ARRAY_SIZE(volt_ranges), \
+ .enable_reg = _enable_reg, \
+ .enable_mask = _enable_mask, \
+ .of_map_mode = mt6392_map_mode, \
+ .ramp_delay = _ramp_delay, \
+ }, \
+ .qi_status_reg = _qi_status_reg, \
+ .qi_status_mask = _qi_status_mask, \
+ .vselctrl_reg = _vselctrl_reg, \
+ .vselctrl_mask = _vselctrl_mask, \
+ .vsel_reg_mode_reg = _vsel_reg_mode_reg, \
+ .vsel_reg_mode_mask = _vsel_reg_mode_mask, \
+ .vsel_normal_mode_reg = _vsel_normal_mode_reg, \
+ .vsel_normal_mode_mask = _vsel_normal_mode_mask, \
+ .pwm_modeset_reg = _pwm_modeset_reg, \
+ .pwm_modeset_mask = _pwm_modeset_mask, \
+}
+
+#define MT6392_LDO(match, vreg, supply, ldo_volt_table, \
+ _qi_status_reg, _qi_status_mask, \
+ _enable_reg, _enable_mask, \
+ _vsel_reg, _vsel_mask, \
+ _lp_modeget_reg, _lp_modeget_mask, \
+ _lp_modeset_reg, _lp_modeset_mask, \
+ _enable_time) \
+[MT6392_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .supply_name = supply, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .ops = &mt6392_volt_table_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6392_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ARRAY_SIZE(ldo_volt_table), \
+ .volt_table = ldo_volt_table, \
+ .vsel_reg = _vsel_reg, \
+ .vsel_mask = _vsel_mask, \
+ .enable_reg = _enable_reg, \
+ .enable_mask = _enable_mask, \
+ .enable_time = _enable_time, \
+ .of_map_mode = mt6392_map_mode, \
+ }, \
+ .qi_status_reg = _qi_status_reg, \
+ .qi_status_mask = _qi_status_mask, \
+ .lp_modeget_reg = _lp_modeget_reg, \
+ .lp_modeget_mask = _lp_modeget_mask, \
+ .lp_modeset_reg = _lp_modeset_reg, \
+ .lp_modeset_mask = _lp_modeset_mask, \
+}
+
+#define MT6392_LDO_LINEAR(match, vreg, supply, min, max, step, \
+ volt_ranges, \
+ _qi_status_reg, _qi_status_mask, \
+ _enable_reg, _enable_mask, \
+ _vsel_reg, _vsel_mask, \
+ _lp_modeget_reg, _lp_modeget_mask, \
+ _lp_modeset_reg, _lp_modeset_mask, \
+ _enable_time) \
+[MT6392_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .supply_name = supply, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .ops = &mt6392_volt_ldo_range_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6392_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = ((max) - (min)) / (step) + 1, \
+ .linear_ranges = volt_ranges, \
+ .n_linear_ranges = ARRAY_SIZE(volt_ranges), \
+ .vsel_reg = _vsel_reg, \
+ .vsel_mask = _vsel_mask, \
+ .enable_reg = _enable_reg, \
+ .enable_mask = _enable_mask, \
+ .enable_time = _enable_time, \
+ .of_map_mode = mt6392_map_mode, \
+ }, \
+ .qi_status_reg = _qi_status_reg, \
+ .qi_status_mask = _qi_status_mask, \
+ .lp_modeget_reg = _lp_modeget_reg, \
+ .lp_modeget_mask = _lp_modeget_mask, \
+ .lp_modeset_reg = _lp_modeset_reg, \
+ .lp_modeset_mask = _lp_modeset_mask, \
+}
+
+#define MT6392_REG_FIXED(match, vreg, supply, volt, \
+ _qi_status_reg, _qi_status_mask, \
+ _enable_reg, _enable_mask, \
+ _lp_modeget_reg, _lp_modeget_mask, \
+ _lp_modeset_reg, _lp_modeset_mask, \
+ _enable_time) \
+[MT6392_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .supply_name = supply, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .ops = &mt6392_volt_fixed_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6392_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = 1, \
+ .min_uV = volt, \
+ .enable_reg = _enable_reg, \
+ .enable_mask = _enable_mask, \
+ .enable_time = _enable_time, \
+ .of_map_mode = mt6392_map_mode, \
+ }, \
+ .qi_status_reg = _qi_status_reg, \
+ .qi_status_mask = _qi_status_mask, \
+ .lp_modeget_reg = _lp_modeget_reg, \
+ .lp_modeget_mask = _lp_modeget_mask, \
+ .lp_modeset_reg = _lp_modeset_reg, \
+ .lp_modeset_mask = _lp_modeset_mask, \
+}
+
+#define MT6392_REG_FIXED_NO_MODE(match, vreg, supply, volt, \
+ _qi_status_reg, _qi_status_mask, \
+ _enable_reg, _enable_mask, _enable_time) \
+[MT6392_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .supply_name = supply, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .ops = &mt6392_volt_fixed_no_mode_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6392_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = 1, \
+ .min_uV = volt, \
+ .enable_reg = _enable_reg, \
+ .enable_mask = _enable_mask, \
+ .enable_time = _enable_time, \
+ }, \
+ .qi_status_reg = _qi_status_reg, \
+ .qi_status_mask = _qi_status_mask, \
+}
+
+#define MT6392_REG(match, vreg, supply, volt) \
+[MT6392_ID_##vreg] = { \
+ .desc = { \
+ .name = #vreg, \
+ .supply_name = supply, \
+ .of_match = of_match_ptr(match), \
+ .regulators_node = of_match_ptr("regulators"), \
+ .ops = &mt6392_volt_no_ops, \
+ .type = REGULATOR_VOLTAGE, \
+ .id = MT6392_ID_##vreg, \
+ .owner = THIS_MODULE, \
+ .n_voltages = 1, \
+ .min_uV = volt, \
+ }, \
+}
+
+static const struct linear_range buck_volt_range1[] = {
+ REGULATOR_LINEAR_RANGE(700000, 0, 0x7f, 6250),
+};
+
+static const struct linear_range buck_volt_range2[] = {
+ REGULATOR_LINEAR_RANGE(1400000, 0, 0x7f, 12500),
+};
+
+static const u32 ldo_volt_table1[] = {
+ 1800000, 1900000, 2000000, 2200000,
+};
+
+static const struct linear_range ldo_volt_range2[] = {
+ REGULATOR_LINEAR_RANGE(3300000, 0, 3, 100000),
+};
+
+static const u32 ldo_volt_table3[] = {
+ 1800000, 3300000,
+};
+
+static const u32 ldo_volt_table4[] = {
+ 3000000, 3300000,
+};
+
+static const u32 ldo_volt_table5[] = {
+ 1200000, 1300000, 1500000, 1800000, 2000000, 2800000, 3000000, 3300000,
+};
+
+static const u32 ldo_volt_table6[] = {
+ 1240000, 1390000,
+};
+
+static const u32 ldo_volt_table7[] = {
+ 1200000, 1300000, 1500000, 1800000,
+};
+
+static const u32 ldo_volt_table8[] = {
+ 1800000, 2000000,
+};
+
+static unsigned int mt6392_map_mode(unsigned int mode)
+{
+ switch (mode) {
+ case MT6392_REGULATOR_MODE_NORMAL:
+ return REGULATOR_MODE_NORMAL;
+ case MT6392_BUCK_MODE_FORCE_PWM:
+ return REGULATOR_MODE_FAST;
+ case MT6392_LDO_MODE_LP:
+ return REGULATOR_MODE_STANDBY;
+ default:
+ return REGULATOR_MODE_INVALID;
+ }
+}
+
+static int mt6392_buck_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ int ret, val = 0;
+ struct mt6392_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (!info->pwm_modeset_mask) {
+ dev_err(&rdev->dev, "regulator %s doesn't support set_mode\n", info->desc.name);
+ return -EINVAL;
+ }
+
+ switch (mode) {
+ case REGULATOR_MODE_FAST:
+ val = 1;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ val <<= ffs(info->pwm_modeset_mask) - 1;
+
+ ret = regmap_update_bits(rdev->regmap, info->pwm_modeset_reg,
+ info->pwm_modeset_mask, val);
+
+ return ret;
+}
+
+static unsigned int mt6392_buck_get_mode(struct regulator_dev *rdev)
+{
+ unsigned int val;
+ unsigned int mode;
+ int ret;
+ struct mt6392_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (!info->pwm_modeset_mask) {
+ dev_err(&rdev->dev, "regulator %s doesn't support get_mode\n", info->desc.name);
+ return -EINVAL;
+ }
+
+ ret = regmap_read(rdev->regmap, info->pwm_modeset_reg, &val);
+ if (ret < 0)
+ return ret;
+
+ val &= info->pwm_modeset_mask;
+ val >>= ffs(info->pwm_modeset_mask) - 1;
+
+ if (val & 0x1)
+ mode = REGULATOR_MODE_FAST;
+ else
+ mode = REGULATOR_MODE_NORMAL;
+
+ return mode;
+}
+
+static int mt6392_ldo_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+ int ret, val = 0;
+ struct mt6392_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (!info->lp_modeset_mask) {
+ dev_err(&rdev->dev, "regulator %s doesn't support set_mode\n",
+ info->desc.name);
+ return -EINVAL;
+ }
+
+ switch (mode) {
+ case REGULATOR_MODE_STANDBY:
+ val = 1;
+ break;
+ case REGULATOR_MODE_NORMAL:
+ val = 0;
+ break;
+ default:
+ return -EINVAL;
+ }
+
+ val <<= ffs(info->lp_modeset_mask) - 1;
+
+ ret = regmap_update_bits(rdev->regmap, info->lp_modeset_reg,
+ info->lp_modeset_mask, val);
+
+ return ret;
+}
+
+static unsigned int mt6392_ldo_get_mode(struct regulator_dev *rdev)
+{
+ unsigned int val;
+ unsigned int mode;
+ int ret;
+ struct mt6392_regulator_info *info = rdev_get_drvdata(rdev);
+
+ if (!info->lp_modeget_mask) {
+ dev_err(&rdev->dev, "regulator %s doesn't support get_mode\n",
+ info->desc.name);
+ return -EINVAL;
+ }
+
+ ret = regmap_read(rdev->regmap, info->lp_modeget_reg, &val);
+ if (ret < 0)
+ return ret;
+
+ val &= info->lp_modeget_mask;
+ val >>= ffs(info->lp_modeget_mask) - 1;
+
+ if (val & 0x1)
+ mode = REGULATOR_MODE_STANDBY;
+ else
+ mode = REGULATOR_MODE_NORMAL;
+
+ return mode;
+}
+
+static int mt6392_get_status(struct regulator_dev *rdev)
+{
+ int ret;
+ u32 regval;
+ struct mt6392_regulator_info *info = rdev_get_drvdata(rdev);
+
+ ret = regmap_read(rdev->regmap, info->qi_status_reg, ®val);
+ if (ret != 0) {
+ dev_err(&rdev->dev, "Failed to read qi_status_reg: %d\n", ret);
+ return ret;
+ }
+
+ return (regval & info->qi_status_mask) ? REGULATOR_STATUS_ON : REGULATOR_STATUS_OFF;
+}
+
+static const struct regulator_ops mt6392_volt_range_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6392_get_status,
+ .set_mode = mt6392_buck_set_mode,
+ .get_mode = mt6392_buck_get_mode,
+};
+
+static const struct regulator_ops mt6392_volt_table_ops = {
+ .list_voltage = regulator_list_voltage_table,
+ .map_voltage = regulator_map_voltage_iterate,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6392_get_status,
+ .set_mode = mt6392_ldo_set_mode,
+ .get_mode = mt6392_ldo_get_mode,
+};
+
+static const struct regulator_ops mt6392_volt_ldo_range_ops = {
+ .list_voltage = regulator_list_voltage_linear_range,
+ .map_voltage = regulator_map_voltage_linear_range,
+ .set_voltage_sel = regulator_set_voltage_sel_regmap,
+ .get_voltage_sel = regulator_get_voltage_sel_regmap,
+ .set_voltage_time_sel = regulator_set_voltage_time_sel,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6392_get_status,
+ .set_mode = mt6392_ldo_set_mode,
+ .get_mode = mt6392_ldo_get_mode,
+};
+
+static const struct regulator_ops mt6392_volt_fixed_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6392_get_status,
+ .set_mode = mt6392_ldo_set_mode,
+ .get_mode = mt6392_ldo_get_mode,
+};
+
+static const struct regulator_ops mt6392_volt_fixed_no_mode_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+ .enable = regulator_enable_regmap,
+ .disable = regulator_disable_regmap,
+ .is_enabled = regulator_is_enabled_regmap,
+ .get_status = mt6392_get_status,
+};
+
+static const struct regulator_ops mt6392_volt_no_ops = {
+ .list_voltage = regulator_list_voltage_linear,
+};
+
+/* The array is indexed by id(MT6392_ID_XXX) */
+static struct mt6392_regulator_info mt6392_regulators[] = {
+ MT6392_BUCK("vproc", VPROC, "vproc", 700000, 1493750, 6250,
+ buck_volt_range1,
+ MT6392_VPROC_CON7, BIT(13), // Regulator status
+ MT6392_VPROC_CON7, BIT(0), // Regulator enable
+ MT6392_VPROC_CON5, BIT(0), // Vsel ctrl mode selector,not present in data sheet
+ MT6392_VPROC_CON9, GENMASK(6, 0), // Vsel when control mode = register (0)
+ MT6392_VPROC_CON10, GENMASK(6, 0), // Vsel when control mode = normal (1)
+ MT6392_VPROC_CON2, BIT(8), // Auto / Force PWM mode
+ 12500),
+ MT6392_BUCK("vsys", VSYS, "vsys", 1400000, 2987500, 12500,
+ buck_volt_range2,
+ MT6392_VSYS_CON7, BIT(13),
+ MT6392_VSYS_CON7, BIT(0),
+ MT6392_VSYS_CON5, BIT(0), // Not present in data sheet
+ MT6392_VSYS_CON9, GENMASK(6, 0),
+ MT6392_VSYS_CON10, GENMASK(6, 0),
+ MT6392_VSYS_CON2, BIT(8),
+ 25000),
+ MT6392_BUCK("vcore", VCORE, "vcore", 700000, 1493750, 6250,
+ buck_volt_range1,
+ MT6392_VCORE_CON7, BIT(13),
+ MT6392_VCORE_CON7, BIT(0),
+ MT6392_VCORE_CON5, BIT(0), // Not present in data sheet
+ MT6392_VCORE_CON9, GENMASK(6, 0),
+ MT6392_VCORE_CON10, GENMASK(6, 0),
+ MT6392_VCORE_CON2, BIT(8),
+ 12500),
+
+ MT6392_REG_FIXED("vxo22", VXO22, "ldo1", 2200000,
+ MT6392_ANALDO_CON1, BIT(15),
+ MT6392_ANALDO_CON1, BIT(10), // Not present in data sheet
+ MT6392_ANALDO_CON1, BIT(7),
+ MT6392_ANALDO_CON1, BIT(1), // Not present in data sheet
+ 110),
+ MT6392_LDO("vaud22", VAUD22, "ldo1", ldo_volt_table1,
+ MT6392_ANALDO_CON2, BIT(15),
+ MT6392_ANALDO_CON2, BIT(14), // Not present in data sheet
+ MT6392_ANALDO_CON8, GENMASK(6, 5), // Not present in data sheet
+ MT6392_ANALDO_CON2, BIT(7),
+ MT6392_ANALDO_CON2, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG_FIXED_NO_MODE("vcama", VCAMA, "ldo1", 2800000,
+ MT6392_ANALDO_CON4, BIT(15),
+ MT6392_ANALDO_CON4, BIT(15),
+ 264),
+ MT6392_REG_FIXED("vaud28", VAUD28, "ldo1", 2800000,
+ MT6392_ANALDO_CON23, BIT(15),
+ MT6392_ANALDO_CON23, BIT(14), // Not present in data sheet
+ MT6392_ANALDO_CON23, BIT(7),
+ MT6392_ANALDO_CON23, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG_FIXED("vadc18", VADC18, "ldo1", 1800000,
+ MT6392_ANALDO_CON25, BIT(15),
+ MT6392_ANALDO_CON25, BIT(14), // Not present in data sheet
+ MT6392_ANALDO_CON25, BIT(7),
+ MT6392_ANALDO_CON25, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO_LINEAR("vcn35", VCN35, "ldo2", 3300000, 3600000, 100000, ldo_volt_range2,
+ MT6392_ANALDO_CON17, BIT(15), // Not present in data sheet
+ MT6392_ANALDO_CON21, BIT(12), // Not present in data sheet
+ MT6392_ANALDO_CON16, GENMASK(4, 3),
+ MT6392_ANALDO_CON21, BIT(7),
+ MT6392_ANALDO_CON21, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG_FIXED("vio28", VIO28, "ldo2", 2800000,
+ MT6392_DIGLDO_CON0, BIT(15),
+ MT6392_DIGLDO_CON0, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON0, BIT(7),
+ MT6392_DIGLDO_CON0, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG_FIXED("vusb", VUSB, "ldo3", 3300000,
+ MT6392_DIGLDO_CON2, BIT(15),
+ MT6392_DIGLDO_CON2, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON2, BIT(7),
+ MT6392_DIGLDO_CON2, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vmc", VMC, "ldo2", ldo_volt_table3,
+ MT6392_DIGLDO_CON3, BIT(15),
+ MT6392_DIGLDO_CON3, BIT(12),
+ MT6392_DIGLDO_CON24, BIT(4),
+ MT6392_DIGLDO_CON3, BIT(7),
+ MT6392_DIGLDO_CON3, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vmch", VMCH, "ldo2", ldo_volt_table4,
+ MT6392_DIGLDO_CON5, BIT(15),
+ MT6392_DIGLDO_CON5, BIT(14),
+ MT6392_DIGLDO_CON26, BIT(7),
+ MT6392_DIGLDO_CON5, BIT(7),
+ MT6392_DIGLDO_CON5, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vemc3v3", VEMC3V3, "ldo3", ldo_volt_table4,
+ MT6392_DIGLDO_CON6, BIT(15),
+ MT6392_DIGLDO_CON6, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON27, BIT(7),
+ MT6392_DIGLDO_CON6, BIT(7),
+ MT6392_DIGLDO_CON6, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vgp1", VGP1, "ldo3", ldo_volt_table5,
+ MT6392_DIGLDO_CON7, BIT(15),
+ MT6392_DIGLDO_CON7, BIT(15),
+ MT6392_DIGLDO_CON28, GENMASK(7, 5),
+ MT6392_DIGLDO_CON7, BIT(7),
+ MT6392_DIGLDO_CON7, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vgp2", VGP2, "ldo3", ldo_volt_table5,
+ MT6392_DIGLDO_CON8, BIT(15),
+ MT6392_DIGLDO_CON8, BIT(15),
+ MT6392_DIGLDO_CON29, GENMASK(7, 5),
+ MT6392_DIGLDO_CON8, BIT(7),
+ MT6392_DIGLDO_CON8, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG_FIXED("vcn18", VCN18, "avddldo", 1800000,
+ MT6392_DIGLDO_CON11, BIT(15),
+ MT6392_DIGLDO_CON11, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON11, BIT(7),
+ MT6392_DIGLDO_CON11, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vcamaf", VCAMAF, "ldo3", ldo_volt_table5,
+ MT6392_DIGLDO_CON31, BIT(15),
+ MT6392_DIGLDO_CON31, BIT(15),
+ MT6392_DIGLDO_CON32, GENMASK(7, 5),
+ MT6392_DIGLDO_CON31, BIT(7),
+ MT6392_DIGLDO_CON31, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vm", VM, "avddldo", ldo_volt_table6,
+ MT6392_DIGLDO_CON47, BIT(15),
+ MT6392_DIGLDO_CON47, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON48, GENMASK(5, 4), // Not present in data sheet
+ MT6392_DIGLDO_CON47, BIT(7), // Not present in data sheet
+ MT6392_DIGLDO_CON47, BIT(1),
+ 264),
+ MT6392_REG_FIXED("vio18", VIO18, "avddldo", 1800000,
+ MT6392_DIGLDO_CON49, BIT(15),
+ MT6392_DIGLDO_CON49, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON49, BIT(7),
+ MT6392_DIGLDO_CON49, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vcamd", VCAMD, "avddldo", ldo_volt_table7,
+ MT6392_DIGLDO_CON51, BIT(15),
+ MT6392_DIGLDO_CON51, BIT(14),
+ MT6392_DIGLDO_CON52, GENMASK(6, 5),
+ MT6392_DIGLDO_CON51, BIT(7),
+ MT6392_DIGLDO_CON51, BIT(1),
+ 264),
+ MT6392_REG_FIXED("vcamio", VCAMIO, "avddldo", 1800000,
+ MT6392_DIGLDO_CON53, BIT(15),
+ MT6392_DIGLDO_CON53, BIT(14),
+ MT6392_DIGLDO_CON53, BIT(7),
+ MT6392_DIGLDO_CON53, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG_FIXED("vm25", VM25, "ldo3", 2500000,
+ MT6392_DIGLDO_CON55, BIT(15),
+ MT6392_DIGLDO_CON55, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON55, BIT(7),
+ MT6392_DIGLDO_CON55, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_LDO("vefuse", VEFUSE, "ldo2", ldo_volt_table8,
+ MT6392_DIGLDO_CON57, BIT(15),
+ MT6392_DIGLDO_CON57, BIT(14), // Not present in data sheet
+ MT6392_DIGLDO_CON58, BIT(5), // Not present in data sheet
+ MT6392_DIGLDO_CON57, BIT(7),
+ MT6392_DIGLDO_CON57, BIT(1), // Not present in data sheet
+ 264),
+ MT6392_REG("vdig18", VDIG18, "ldo2", 1800000), // Internal non changeable regulator
+ MT6392_REG_FIXED_NO_MODE("vrtc", VRTC, "ldo1", 2800000,
+ MT6392_DIGLDO_CON15, BIT(15),
+ MT6392_DIGLDO_CON15, BIT(8), // Not present in data sheet
+ 264)
+};
+
+// Buck regulators can be in Register mode or Normal mode.
+// Each mode uses a different register to set the desired voltage.
+static int mt6392_set_buck_vsel_reg(struct platform_device *pdev)
+{
+ struct mt6397_chip *mt6392 = dev_get_drvdata(pdev->dev.parent);
+ int i;
+ u32 regval;
+
+ for (i = 0; i < MT6392_MAX_REGULATOR; i++) {
+ if (mt6392_regulators[i].vselctrl_reg) {
+ // Read the vselctrl_reg register
+ if (regmap_read(mt6392->regmap,
+ mt6392_regulators[i].vselctrl_reg,
+ ®val) < 0) {
+ dev_err(&pdev->dev,
+ "Failed to read buck ctrl\n");
+ return -EIO;
+ }
+
+ // vselctrl_reg[vselctrl_mask] defines the mode
+ if (regval & mt6392_regulators[i].vselctrl_mask) {
+ // Regulator in Normal mode
+ mt6392_regulators[i].desc.vsel_reg =
+ mt6392_regulators[i].vsel_normal_mode_reg;
+ mt6392_regulators[i].desc.vsel_mask =
+ mt6392_regulators[i].vsel_normal_mode_mask;
+ } else {
+ // Regulator in Register mode
+ mt6392_regulators[i].desc.vsel_reg =
+ mt6392_regulators[i].vsel_reg_mode_reg;
+ mt6392_regulators[i].desc.vsel_mask =
+ mt6392_regulators[i].vsel_reg_mode_mask;
+ }
+ }
+ }
+
+ return 0;
+}
+
+static int mt6392_regulator_probe(struct platform_device *pdev)
+{
+ struct mt6397_chip *mt6392 = dev_get_drvdata(pdev->dev.parent);
+ struct regulator_config config = {};
+ struct regulator_dev *rdev;
+ int i;
+
+ device_set_of_node_from_dev(&pdev->dev, pdev->dev.parent);
+
+ // Initialize the bucks' vsel_reg and vsel_mask according to current HW state
+ if (mt6392_set_buck_vsel_reg(pdev))
+ return -EIO;
+
+ config.dev = mt6392->dev;
+ config.regmap = mt6392->regmap;
+ for (i = 0; i < MT6392_MAX_REGULATOR; i++) {
+ config.driver_data = &mt6392_regulators[i];
+
+ rdev = devm_regulator_register(&pdev->dev,
+ &mt6392_regulators[i].desc,
+ &config);
+ if (IS_ERR(rdev)) {
+ dev_err(&pdev->dev, "failed to register %s\n",
+ mt6392_regulators[i].desc.name);
+ return PTR_ERR(rdev);
+ }
+ }
+
+ return 0;
+}
+
+static const struct platform_device_id mt6392_platform_ids[] = {
+ { .name = "mt6392-regulator" },
+ { /* sentinel */ },
+};
+MODULE_DEVICE_TABLE(platform, mt6392_platform_ids);
+
+static struct platform_driver mt6392_regulator_driver = {
+ .driver = {
+ .name = "mt6392-regulator",
+ .probe_type = PROBE_PREFER_ASYNCHRONOUS,
+ },
+ .probe = mt6392_regulator_probe,
+ .id_table = mt6392_platform_ids,
+};
+
+module_platform_driver(mt6392_regulator_driver);
+
+MODULE_AUTHOR("Chen Zhong <chen.zhong@mediatek.com>");
+MODULE_DESCRIPTION("Regulator Driver for MediaTek MT6392 PMIC");
+MODULE_LICENSE("GPL");
diff --git a/include/linux/regulator/mt6392-regulator.h b/include/linux/regulator/mt6392-regulator.h
new file mode 100644
index 000000000000..0eccd085b062
--- /dev/null
+++ b/include/linux/regulator/mt6392-regulator.h
@@ -0,0 +1,42 @@
+/* SPDX-License-Identifier: GPL-2.0-only */
+/*
+ * Copyright (c) 2019 MediaTek Inc.
+ * Author: Chen Zhong <chen.zhong@mediatek.com>
+ */
+
+#ifndef __LINUX_REGULATOR_MT6392_H
+#define __LINUX_REGULATOR_MT6392_H
+
+enum {
+ MT6392_ID_VPROC = 0,
+ MT6392_ID_VSYS,
+ MT6392_ID_VCORE,
+ MT6392_ID_VXO22,
+ MT6392_ID_VAUD22,
+ MT6392_ID_VCAMA,
+ MT6392_ID_VAUD28,
+ MT6392_ID_VADC18,
+ MT6392_ID_VCN35,
+ MT6392_ID_VIO28,
+ MT6392_ID_VUSB = 10,
+ MT6392_ID_VMC,
+ MT6392_ID_VMCH,
+ MT6392_ID_VEMC3V3,
+ MT6392_ID_VGP1,
+ MT6392_ID_VGP2,
+ MT6392_ID_VCN18,
+ MT6392_ID_VCAMAF,
+ MT6392_ID_VM,
+ MT6392_ID_VIO18,
+ MT6392_ID_VCAMD,
+ MT6392_ID_VCAMIO,
+ MT6392_ID_VM25,
+ MT6392_ID_VEFUSE,
+ MT6392_ID_VDIG18,
+ MT6392_ID_VRTC,
+ MT6392_ID_RG_MAX,
+};
+
+#define MT6392_MAX_REGULATOR MT6392_ID_RG_MAX
+
+#endif /* __LINUX_REGULATOR_MT6392_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v9 7/9] pinctrl: mediatek: mt6397: Add MediaTek MT6392
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Luca Leonardo Scorcia, AngeloGioacchino Del Regno,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Sen Chu, Sean Wang, Macpaul Lin, Lee Jones, Matthias Brugger,
Liam Girdwood, Mark Brown, Linus Walleij, Louis-Alexis Eyraud,
Julien Massot, Val Packett, Fabien Parent, Akari Tsuyukusa,
Chen Zhong, linux-input, devicetree, linux-kernel, linux-pm,
linux-arm-kernel, linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
Add support for the MT6392 pinctrl device, which is very similar to
MT6397 with a handful of different property values and its own pins
definition.
Update the MT6397 driver to retrieve device data from the match table and
use it for driver init.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
drivers/pinctrl/mediatek/pinctrl-mt6397.c | 37 ++++++++++-
drivers/pinctrl/mediatek/pinctrl-mtk-mt6392.h | 64 +++++++++++++++++++
2 files changed, 99 insertions(+), 2 deletions(-)
create mode 100644 drivers/pinctrl/mediatek/pinctrl-mtk-mt6392.h
diff --git a/drivers/pinctrl/mediatek/pinctrl-mt6397.c b/drivers/pinctrl/mediatek/pinctrl-mt6397.c
index 03d0f65d7bcc..8ba02e70595c 100644
--- a/drivers/pinctrl/mediatek/pinctrl-mt6397.c
+++ b/drivers/pinctrl/mediatek/pinctrl-mt6397.c
@@ -12,10 +12,32 @@
#include <linux/mfd/mt6397/core.h>
#include "pinctrl-mtk-common.h"
+#include "pinctrl-mtk-mt6392.h"
#include "pinctrl-mtk-mt6397.h"
#define MT6397_PIN_REG_BASE 0xc000
+static const struct mtk_pinctrl_devdata mt6392_pinctrl_data = {
+ .pins = mtk_pins_mt6392,
+ .npins = ARRAY_SIZE(mtk_pins_mt6392),
+ .dir_offset = (MT6397_PIN_REG_BASE + 0x000),
+ .ies_offset = MTK_PINCTRL_NOT_SUPPORT,
+ .smt_offset = MTK_PINCTRL_NOT_SUPPORT,
+ .pullen_offset = (MT6397_PIN_REG_BASE + 0x020),
+ .pullsel_offset = (MT6397_PIN_REG_BASE + 0x040),
+ .dout_offset = (MT6397_PIN_REG_BASE + 0x080),
+ .din_offset = (MT6397_PIN_REG_BASE + 0x0a0),
+ .pinmux_offset = (MT6397_PIN_REG_BASE + 0x0c0),
+ .type1_start = 7,
+ .type1_end = 7,
+ .port_shf = 3,
+ .port_mask = 0x3,
+ .port_align = 2,
+ .mode_mask = 0xf,
+ .mode_per_reg = 5,
+ .mode_shf = 4,
+};
+
static const struct mtk_pinctrl_devdata mt6397_pinctrl_data = {
.pins = mtk_pins_mt6397,
.npins = ARRAY_SIZE(mtk_pins_mt6397),
@@ -40,13 +62,24 @@ static const struct mtk_pinctrl_devdata mt6397_pinctrl_data = {
static int mt6397_pinctrl_probe(struct platform_device *pdev)
{
struct mt6397_chip *mt6397;
+ const struct mtk_pinctrl_devdata *data;
+
+ data = device_get_match_data(&pdev->dev);
+ if (!data)
+ return -ENOENT;
mt6397 = dev_get_drvdata(pdev->dev.parent);
- return mtk_pctrl_init(pdev, &mt6397_pinctrl_data, mt6397->regmap);
+ return mtk_pctrl_init(pdev, data, mt6397->regmap);
}
static const struct of_device_id mt6397_pctrl_match[] = {
- { .compatible = "mediatek,mt6397-pinctrl", },
+ {
+ .compatible = "mediatek,mt6392-pinctrl",
+ .data = &mt6392_pinctrl_data
+ }, {
+ .compatible = "mediatek,mt6397-pinctrl",
+ .data = &mt6397_pinctrl_data
+ },
{ }
};
diff --git a/drivers/pinctrl/mediatek/pinctrl-mtk-mt6392.h b/drivers/pinctrl/mediatek/pinctrl-mtk-mt6392.h
new file mode 100644
index 000000000000..e7241af28fdb
--- /dev/null
+++ b/drivers/pinctrl/mediatek/pinctrl-mtk-mt6392.h
@@ -0,0 +1,64 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+#ifndef __PINCTRL_MTK_MT6392_H
+#define __PINCTRL_MTK_MT6392_H
+
+#include <linux/pinctrl/pinctrl.h>
+#include "pinctrl-mtk-common.h"
+
+static const struct mtk_desc_pin mtk_pins_mt6392[] = {
+ MTK_PIN(PINCTRL_PIN(0, "INT"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO0"),
+ MTK_FUNCTION(1, "INT"),
+ MTK_FUNCTION(5, "TEST_CK2"),
+ MTK_FUNCTION(6, "TEST_IN1"),
+ MTK_FUNCTION(7, "TEST_OUT1")
+ ),
+ MTK_PIN(PINCTRL_PIN(1, "SRCLKEN"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO1"),
+ MTK_FUNCTION(1, "SRCLKEN"),
+ MTK_FUNCTION(5, "TEST_CK0"),
+ MTK_FUNCTION(6, "TEST_IN2"),
+ MTK_FUNCTION(7, "TEST_OUT2")
+ ),
+ MTK_PIN(PINCTRL_PIN(2, "RTC_32K1V8"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO2"),
+ MTK_FUNCTION(1, "RTC_32K1V8"),
+ MTK_FUNCTION(5, "TEST_CK1"),
+ MTK_FUNCTION(6, "TEST_IN3"),
+ MTK_FUNCTION(7, "TEST_OUT3")
+ ),
+ MTK_PIN(PINCTRL_PIN(3, "SPI_CLK"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO3"),
+ MTK_FUNCTION(1, "SPI_CLK")
+ ),
+ MTK_PIN(PINCTRL_PIN(4, "SPI_CSN"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO4"),
+ MTK_FUNCTION(1, "SPI_CSN")
+ ),
+ MTK_PIN(PINCTRL_PIN(5, "SPI_MOSI"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO5"),
+ MTK_FUNCTION(1, "SPI_MOSI")
+ ),
+ MTK_PIN(PINCTRL_PIN(6, "SPI_MISO"),
+ NULL, "mt6392",
+ MTK_EINT_FUNCTION(NO_EINT_SUPPORT, NO_EINT_SUPPORT),
+ MTK_FUNCTION(0, "GPIO6"),
+ MTK_FUNCTION(1, "SPI_MISO"),
+ MTK_FUNCTION(6, "TEST_IN4"),
+ MTK_FUNCTION(7, "TEST_OUT4")
+ ),
+};
+
+#endif /* __PINCTRL_MTK_MT6392_H */
--
2.43.0
^ permalink raw reply related
* [PATCH v9 6/9] input: keyboard: mtk-pmic-keys: Add MT6392 support
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Val Packett, Luca Leonardo Scorcia, AngeloGioacchino Del Regno,
Dmitry Torokhov, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Sen Chu, Sean Wang, Macpaul Lin, Lee Jones, Matthias Brugger,
Liam Girdwood, Mark Brown, Linus Walleij, Louis-Alexis Eyraud,
Julien Massot, Fabien Parent, Akari Tsuyukusa, Chen Zhong,
linux-input, devicetree, linux-kernel, linux-pm, linux-arm-kernel,
linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
From: Val Packett <val@packett.cool>
Add support for the MT6392 PMIC to the keys driver.
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
---
drivers/input/keyboard/mtk-pmic-keys.c | 17 +++++++++++++++++
1 file changed, 17 insertions(+)
diff --git a/drivers/input/keyboard/mtk-pmic-keys.c b/drivers/input/keyboard/mtk-pmic-keys.c
index c78d9f6d97c4..8b4a89fce4fb 100644
--- a/drivers/input/keyboard/mtk-pmic-keys.c
+++ b/drivers/input/keyboard/mtk-pmic-keys.c
@@ -13,6 +13,7 @@
#include <linux/mfd/mt6357/registers.h>
#include <linux/mfd/mt6358/registers.h>
#include <linux/mfd/mt6359/registers.h>
+#include <linux/mfd/mt6392/registers.h>
#include <linux/mfd/mt6397/core.h>
#include <linux/mfd/mt6397/registers.h>
#include <linux/module.h>
@@ -69,6 +70,19 @@ static const struct mtk_pmic_regs mt6397_regs = {
.rst_lprst_mask = MTK_PMIC_RST_DU_MASK,
};
+static const struct mtk_pmic_regs mt6392_regs = {
+ .keys_regs[MTK_PMIC_PWRKEY_INDEX] =
+ MTK_PMIC_KEYS_REGS(MT6392_CHRSTATUS, 0x2,
+ MT6392_INT_MISC_CON, 0x10,
+ MTK_PMIC_PWRKEY_RST),
+ .keys_regs[MTK_PMIC_HOMEKEY_INDEX] =
+ MTK_PMIC_KEYS_REGS(MT6392_CHRSTATUS, 0x4,
+ MT6392_INT_MISC_CON, 0x8,
+ MTK_PMIC_HOMEKEY_RST),
+ .pmic_rst_reg = MT6392_TOP_RST_MISC,
+ .rst_lprst_mask = MTK_PMIC_RST_DU_MASK,
+};
+
static const struct mtk_pmic_regs mt6323_regs = {
.keys_regs[MTK_PMIC_PWRKEY_INDEX] =
MTK_PMIC_KEYS_REGS(MT6323_CHRSTATUS,
@@ -301,6 +315,9 @@ static const struct of_device_id of_mtk_pmic_keys_match_tbl[] = {
{
.compatible = "mediatek,mt6397-keys",
.data = &mt6397_regs,
+ }, {
+ .compatible = "mediatek,mt6392-keys",
+ .data = &mt6392_regs,
}, {
.compatible = "mediatek,mt6323-keys",
.data = &mt6323_regs,
--
2.43.0
^ permalink raw reply related
* [PATCH v9 5/9] mfd: mt6397: Add support for MT6392 PMIC
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Fabien Parent, Val Packett, Luca Leonardo Scorcia,
AngeloGioacchino Del Regno, Dmitry Torokhov, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sen Chu, Sean Wang,
Macpaul Lin, Lee Jones, Matthias Brugger, Liam Girdwood,
Mark Brown, Linus Walleij, Louis-Alexis Eyraud, Julien Massot,
Akari Tsuyukusa, Chen Zhong, linux-input, devicetree,
linux-kernel, linux-pm, linux-arm-kernel, linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
From: Fabien Parent <parent.f@gmail.com>
Align the MT6397 PMIC driver to other MFD drivers by passing only an
identifier through mt6397_of_match[*].data and add support for the MT6392
PMIC and its regulator, RTC, keys and pinctrl devices.
The keys device manages two buttons named PWRKEY and FCHR_ENB, the latter
is identified as "Force charging disable" in the data sheet but it also
says "Merge with HOMEKEY", so call it "Home" for consistency.
Signed-off-by: Fabien Parent <parent.f@gmail.com>
Signed-off-by: Val Packett <val@packett.cool>
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
---
drivers/mfd/mt6397-core.c | 98 ++++--
drivers/mfd/mt6397-irq.c | 8 +
include/linux/mfd/mt6392/core.h | 43 +++
include/linux/mfd/mt6392/registers.h | 488 +++++++++++++++++++++++++++
include/linux/mfd/mt6397/core.h | 1 +
5 files changed, 612 insertions(+), 26 deletions(-)
create mode 100644 include/linux/mfd/mt6392/core.h
create mode 100644 include/linux/mfd/mt6392/registers.h
diff --git a/drivers/mfd/mt6397-core.c b/drivers/mfd/mt6397-core.c
index ccd97d66d7f1..f683e878543e 100644
--- a/drivers/mfd/mt6397-core.c
+++ b/drivers/mfd/mt6397-core.c
@@ -18,6 +18,7 @@
#include <linux/mfd/mt6357/core.h>
#include <linux/mfd/mt6358/core.h>
#include <linux/mfd/mt6359/core.h>
+#include <linux/mfd/mt6392/core.h>
#include <linux/mfd/mt6397/core.h>
#include <linux/mfd/mt6323/registers.h>
#include <linux/mfd/mt6328/registers.h>
@@ -25,6 +26,7 @@
#include <linux/mfd/mt6357/registers.h>
#include <linux/mfd/mt6358/registers.h>
#include <linux/mfd/mt6359/registers.h>
+#include <linux/mfd/mt6392/registers.h>
#include <linux/mfd/mt6397/registers.h>
#define MT6323_RTC_BASE 0x8000
@@ -39,6 +41,9 @@
#define MT6358_RTC_BASE 0x0588
#define MT6358_RTC_SIZE 0x3c
+#define MT6392_RTC_BASE 0x8000
+#define MT6392_RTC_SIZE 0x3e
+
#define MT6397_RTC_BASE 0xe000
#define MT6397_RTC_SIZE 0x3e
@@ -65,6 +70,11 @@ static const struct resource mt6358_rtc_resources[] = {
DEFINE_RES_IRQ(MT6358_IRQ_RTC),
};
+static const struct resource mt6392_rtc_resources[] = {
+ DEFINE_RES_MEM(MT6392_RTC_BASE, MT6392_RTC_SIZE),
+ DEFINE_RES_IRQ(MT6392_IRQ_RTC),
+};
+
static const struct resource mt6397_rtc_resources[] = {
DEFINE_RES_MEM(MT6397_RTC_BASE, MT6397_RTC_SIZE),
DEFINE_RES_IRQ(MT6397_IRQ_RTC),
@@ -114,6 +124,11 @@ static const struct resource mt6331_keys_resources[] = {
DEFINE_RES_IRQ_NAMED(MT6331_IRQ_STATUS_HOMEKEY, "homekey"),
};
+static const struct resource mt6392_keys_resources[] = {
+ DEFINE_RES_IRQ_NAMED(MT6392_IRQ_PWRKEY, "powerkey"),
+ DEFINE_RES_IRQ_NAMED(MT6392_IRQ_FCHRKEY, "homekey"),
+};
+
static const struct resource mt6397_keys_resources[] = {
DEFINE_RES_IRQ_NAMED(MT6397_IRQ_PWRKEY, "powerkey"),
DEFINE_RES_IRQ_NAMED(MT6397_IRQ_HOMEKEY, "homekey"),
@@ -193,6 +208,16 @@ static const struct mfd_cell mt6359_devs[] = {
"mediatek,mt6359-accdet"),
};
+static const struct mfd_cell mt6392_devs[] = {
+ MFD_CELL_OF("mt6392-keys", mt6392_keys_resources, NULL, 0, 0,
+ "mediatek,mt6392-keys"),
+ MFD_CELL_OF("mt6392-pinctrl", NULL, NULL, 0, 0,
+ "mediatek,mt6392-pinctrl"),
+ MFD_CELL_NAME("mt6392-regulator"),
+ MFD_CELL_OF("mt6392-rtc", mt6392_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6392-rtc"),
+};
+
static const struct mfd_cell mt6397_devs[] = {
MFD_CELL_OF("mt6397-rtc", mt6397_rtc_resources, NULL, 0, 0,
"mediatek,mt6397-rtc"),
@@ -264,6 +289,14 @@ static const struct chip_data mt6359_core = {
.irq_init = mt6358_irq_init,
};
+static const struct chip_data mt6392_core = {
+ .cid_addr = MT6392_CID,
+ .cid_shift = 0,
+ .cells = mt6392_devs,
+ .cell_size = ARRAY_SIZE(mt6392_devs),
+ .irq_init = mt6397_irq_init,
+};
+
static const struct chip_data mt6397_core = {
.cid_addr = MT6397_CID,
.cid_shift = 0,
@@ -278,6 +311,7 @@ static int mt6397_probe(struct platform_device *pdev)
unsigned int id = 0;
struct mt6397_chip *pmic;
const struct chip_data *pmic_core;
+ int chip_variant;
pmic = devm_kzalloc(&pdev->dev, sizeof(*pmic), GFP_KERNEL);
if (!pmic)
@@ -293,9 +327,36 @@ static int mt6397_probe(struct platform_device *pdev)
if (!pmic->regmap)
return -ENODEV;
- pmic_core = of_device_get_match_data(&pdev->dev);
- if (!pmic_core)
+ chip_variant = (unsigned int)(uintptr_t)device_get_match_data(&pdev->dev);
+ switch (chip_variant) {
+ case MT6323_CHIP_ID:
+ pmic_core = &mt6323_core;
+ break;
+ case MT6328_CHIP_ID:
+ pmic_core = &mt6328_core;
+ break;
+ case MT6331_CHIP_ID:
+ pmic_core = &mt6331_mt6332_core;
+ break;
+ case MT6357_CHIP_ID:
+ pmic_core = &mt6357_core;
+ break;
+ case MT6358_CHIP_ID:
+ pmic_core = &mt6358_core;
+ break;
+ case MT6359_CHIP_ID:
+ pmic_core = &mt6359_core;
+ break;
+ case MT6392_CHIP_ID:
+ pmic_core = &mt6392_core;
+ break;
+ case MT6397_CHIP_ID:
+ pmic_core = &mt6397_core;
+ break;
+ default:
+ dev_err(&pdev->dev, "Device not supported\n");
return -ENODEV;
+ }
ret = regmap_read(pmic->regmap, pmic_core->cid_addr, &id);
if (ret) {
@@ -327,30 +388,15 @@ static int mt6397_probe(struct platform_device *pdev)
}
static const struct of_device_id mt6397_of_match[] = {
- {
- .compatible = "mediatek,mt6323",
- .data = &mt6323_core,
- }, {
- .compatible = "mediatek,mt6328",
- .data = &mt6328_core,
- }, {
- .compatible = "mediatek,mt6331",
- .data = &mt6331_mt6332_core,
- }, {
- .compatible = "mediatek,mt6357",
- .data = &mt6357_core,
- }, {
- .compatible = "mediatek,mt6358",
- .data = &mt6358_core,
- }, {
- .compatible = "mediatek,mt6359",
- .data = &mt6359_core,
- }, {
- .compatible = "mediatek,mt6397",
- .data = &mt6397_core,
- }, {
- /* sentinel */
- }
+ { .compatible = "mediatek,mt6323", .data = (void *)MT6323_CHIP_ID, },
+ { .compatible = "mediatek,mt6328", .data = (void *)MT6328_CHIP_ID, },
+ { .compatible = "mediatek,mt6331", .data = (void *)MT6331_CHIP_ID, },
+ { .compatible = "mediatek,mt6357", .data = (void *)MT6357_CHIP_ID, },
+ { .compatible = "mediatek,mt6358", .data = (void *)MT6358_CHIP_ID, },
+ { .compatible = "mediatek,mt6359", .data = (void *)MT6359_CHIP_ID, },
+ { .compatible = "mediatek,mt6392", .data = (void *)MT6392_CHIP_ID, },
+ { .compatible = "mediatek,mt6397", .data = (void *)MT6397_CHIP_ID, },
+ { /* sentinel */ }
};
MODULE_DEVICE_TABLE(of, mt6397_of_match);
diff --git a/drivers/mfd/mt6397-irq.c b/drivers/mfd/mt6397-irq.c
index 5d2e5459f744..80ea5b92d232 100644
--- a/drivers/mfd/mt6397-irq.c
+++ b/drivers/mfd/mt6397-irq.c
@@ -15,6 +15,8 @@
#include <linux/mfd/mt6328/registers.h>
#include <linux/mfd/mt6331/core.h>
#include <linux/mfd/mt6331/registers.h>
+#include <linux/mfd/mt6392/core.h>
+#include <linux/mfd/mt6392/registers.h>
#include <linux/mfd/mt6397/core.h>
#include <linux/mfd/mt6397/registers.h>
@@ -203,6 +205,12 @@ int mt6397_irq_init(struct mt6397_chip *chip)
chip->int_status[0] = MT6397_INT_STATUS0;
chip->int_status[1] = MT6397_INT_STATUS1;
break;
+ case MT6392_CHIP_ID:
+ chip->int_con[0] = MT6392_INT_CON0;
+ chip->int_con[1] = MT6392_INT_CON1;
+ chip->int_status[0] = MT6392_INT_STATUS0;
+ chip->int_status[1] = MT6392_INT_STATUS1;
+ break;
default:
dev_err(chip->dev, "unsupported chip: 0x%x\n", chip->chip_id);
diff --git a/include/linux/mfd/mt6392/core.h b/include/linux/mfd/mt6392/core.h
new file mode 100644
index 000000000000..8777b3abf929
--- /dev/null
+++ b/include/linux/mfd/mt6392/core.h
@@ -0,0 +1,43 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 MediaTek Inc.
+ * Copyright (c) 2026 Luca Leonardo Scorcia <l.scorcia@gmail.com>
+ * Author: Chen Zhong <chen.zhong@mediatek.com>
+ */
+
+#ifndef __MFD_MT6392_CORE_H__
+#define __MFD_MT6392_CORE_H__
+
+enum mt6392_irq_numbers {
+ MT6392_IRQ_SPKL_AB = 0,
+ MT6392_IRQ_SPKL,
+ MT6392_IRQ_BAT_L,
+ MT6392_IRQ_BAT_H,
+ MT6392_IRQ_WATCHDOG,
+ MT6392_IRQ_PWRKEY,
+ MT6392_IRQ_THR_L,
+ MT6392_IRQ_THR_H,
+ MT6392_IRQ_VBATON_UNDET,
+ MT6392_IRQ_BVALID_DET,
+ MT6392_IRQ_CHRDET,
+ MT6392_IRQ_OV,
+ MT6392_IRQ_LDO = 16,
+ MT6392_IRQ_FCHRKEY,
+ MT6392_IRQ_RELEASE_PWRKEY,
+ MT6392_IRQ_RELEASE_FCHRKEY,
+ MT6392_IRQ_RTC,
+ MT6392_IRQ_VPROC,
+ MT6392_IRQ_VSYS,
+ MT6392_IRQ_VCORE,
+ MT6392_IRQ_TYPE_C_CC,
+ MT6392_IRQ_TYPEC_H_MAX,
+ MT6392_IRQ_TYPEC_H_MIN,
+ MT6392_IRQ_TYPEC_L_MAX,
+ MT6392_IRQ_TYPEC_L_MIN,
+ MT6392_IRQ_THR_MAX,
+ MT6392_IRQ_THR_MIN,
+ MT6392_IRQ_NAG_C_DLTV,
+ MT6392_IRQ_NR,
+};
+
+#endif /* __MFD_MT6392_CORE_H__ */
diff --git a/include/linux/mfd/mt6392/registers.h b/include/linux/mfd/mt6392/registers.h
new file mode 100644
index 000000000000..68fe9af448f5
--- /dev/null
+++ b/include/linux/mfd/mt6392/registers.h
@@ -0,0 +1,488 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Copyright (c) 2020 MediaTek Inc.
+ * Copyright (c) 2026 Luca Leonardo Scorcia <l.scorcia@gmail.com>
+ * Author: Chen Zhong <chen.zhong@mediatek.com>
+ */
+
+#ifndef __MFD_MT6392_REGISTERS_H__
+#define __MFD_MT6392_REGISTERS_H__
+
+/* PMIC Registers */
+#define MT6392_CHR_CON0 0x0000
+#define MT6392_CHR_CON1 0x0002
+#define MT6392_CHR_CON2 0x0004
+#define MT6392_CHR_CON3 0x0006
+#define MT6392_CHR_CON4 0x0008
+#define MT6392_CHR_CON5 0x000A
+#define MT6392_CHR_CON6 0x000C
+#define MT6392_CHR_CON7 0x000E
+#define MT6392_CHR_CON8 0x0010
+#define MT6392_CHR_CON9 0x0012
+#define MT6392_CHR_CON10 0x0014
+#define MT6392_CHR_CON11 0x0016
+#define MT6392_CHR_CON12 0x0018
+#define MT6392_CHR_CON13 0x001A
+#define MT6392_CHR_CON14 0x001C
+#define MT6392_CHR_CON15 0x001E
+#define MT6392_CHR_CON16 0x0020
+#define MT6392_CHR_CON17 0x0022
+#define MT6392_CHR_CON18 0x0024
+#define MT6392_CHR_CON19 0x0026
+#define MT6392_CHR_CON20 0x0028
+#define MT6392_CHR_CON21 0x002A
+#define MT6392_CHR_CON22 0x002C
+#define MT6392_CHR_CON23 0x002E
+#define MT6392_CHR_CON24 0x0030
+#define MT6392_CHR_CON25 0x0032
+#define MT6392_CHR_CON26 0x0034
+#define MT6392_CHR_CON27 0x0036
+#define MT6392_CHR_CON28 0x0038
+#define MT6392_CHR_CON29 0x003A
+#define MT6392_STRUP_CON0 0x003C
+#define MT6392_STRUP_CON2 0x003E
+#define MT6392_STRUP_CON3 0x0040
+#define MT6392_STRUP_CON4 0x0042
+#define MT6392_STRUP_CON5 0x0044
+#define MT6392_STRUP_CON6 0x0046
+#define MT6392_STRUP_CON7 0x0048
+#define MT6392_STRUP_CON8 0x004A
+#define MT6392_STRUP_CON9 0x004C
+#define MT6392_STRUP_CON10 0x004E
+#define MT6392_STRUP_CON11 0x0050
+#define MT6392_SPK_CON0 0x0052
+#define MT6392_SPK_CON1 0x0054
+#define MT6392_SPK_CON2 0x0056
+#define MT6392_SPK_CON6 0x005E
+#define MT6392_SPK_CON7 0x0060
+#define MT6392_SPK_CON8 0x0062
+#define MT6392_SPK_CON9 0x0064
+#define MT6392_SPK_CON10 0x0066
+#define MT6392_SPK_CON11 0x0068
+#define MT6392_SPK_CON12 0x006A
+#define MT6392_STRUP_CON12 0x006E
+#define MT6392_STRUP_CON13 0x0070
+#define MT6392_STRUP_CON14 0x0072
+#define MT6392_STRUP_CON15 0x0074
+#define MT6392_STRUP_CON16 0x0076
+#define MT6392_STRUP_CON17 0x0078
+#define MT6392_STRUP_CON18 0x007A
+#define MT6392_STRUP_CON19 0x007C
+#define MT6392_STRUP_CON20 0x007E
+#define MT6392_CID 0x0100
+#define MT6392_TOP_CKPDN0 0x0102
+#define MT6392_TOP_CKPDN0_SET 0x0104
+#define MT6392_TOP_CKPDN0_CLR 0x0106
+#define MT6392_TOP_CKPDN1 0x0108
+#define MT6392_TOP_CKPDN1_SET 0x010A
+#define MT6392_TOP_CKPDN1_CLR 0x010C
+#define MT6392_TOP_CKPDN2 0x010E
+#define MT6392_TOP_CKPDN2_SET 0x0110
+#define MT6392_TOP_CKPDN2_CLR 0x0112
+#define MT6392_TOP_RST_CON 0x0114
+#define MT6392_TOP_RST_CON_SET 0x0116
+#define MT6392_TOP_RST_CON_CLR 0x0118
+#define MT6392_TOP_RST_MISC 0x011A
+#define MT6392_TOP_RST_MISC_SET 0x011C
+#define MT6392_TOP_RST_MISC_CLR 0x011E
+#define MT6392_TOP_CKCON0 0x0120
+#define MT6392_TOP_CKCON0_SET 0x0122
+#define MT6392_TOP_CKCON0_CLR 0x0124
+#define MT6392_TOP_CKCON1 0x0126
+#define MT6392_TOP_CKCON1_SET 0x0128
+#define MT6392_TOP_CKCON1_CLR 0x012A
+#define MT6392_TOP_CKTST0 0x012C
+#define MT6392_TOP_CKTST1 0x012E
+#define MT6392_TOP_CKTST2 0x0130
+#define MT6392_TEST_OUT 0x0132
+#define MT6392_TEST_CON0 0x0134
+#define MT6392_TEST_CON1 0x0136
+#define MT6392_EN_STATUS0 0x0138
+#define MT6392_EN_STATUS1 0x013A
+#define MT6392_OCSTATUS0 0x013C
+#define MT6392_OCSTATUS1 0x013E
+#define MT6392_PGSTATUS 0x0140
+#define MT6392_CHRSTATUS 0x0142
+#define MT6392_TDSEL_CON 0x0144
+#define MT6392_RDSEL_CON 0x0146
+#define MT6392_SMT_CON0 0x0148
+#define MT6392_SMT_CON1 0x014A
+#define MT6392_DRV_CON0 0x0152
+#define MT6392_DRV_CON1 0x0154
+#define MT6392_INT_CON0 0x0160
+#define MT6392_INT_CON0_SET 0x0162
+#define MT6392_INT_CON0_CLR 0x0164
+#define MT6392_INT_CON1 0x0166
+#define MT6392_INT_CON1_SET 0x0168
+#define MT6392_INT_CON1_CLR 0x016A
+#define MT6392_INT_MISC_CON 0x016C
+#define MT6392_INT_MISC_CON_SET 0x016E
+#define MT6392_INT_MISC_CON_CLR 0x0170
+#define MT6392_INT_STATUS0 0x0172
+#define MT6392_INT_STATUS1 0x0174
+#define MT6392_OC_GEAR_0 0x0176
+#define MT6392_OC_GEAR_1 0x0178
+#define MT6392_OC_GEAR_2 0x017A
+#define MT6392_OC_CTL_VPROC 0x017C
+#define MT6392_OC_CTL_VSYS 0x017E
+#define MT6392_OC_CTL_VCORE 0x0180
+#define MT6392_FQMTR_CON0 0x0182
+#define MT6392_FQMTR_CON1 0x0184
+#define MT6392_FQMTR_CON2 0x0186
+#define MT6392_RG_SPI_CON 0x0188
+#define MT6392_DEW_DIO_EN 0x018A
+#define MT6392_DEW_READ_TEST 0x018C
+#define MT6392_DEW_WRITE_TEST 0x018E
+#define MT6392_DEW_CRC_SWRST 0x0190
+#define MT6392_DEW_CRC_EN 0x0192
+#define MT6392_DEW_CRC_VAL 0x0194
+#define MT6392_DEW_DBG_MON_SEL 0x0196
+#define MT6392_DEW_CIPHER_KEY_SEL 0x0198
+#define MT6392_DEW_CIPHER_IV_SEL 0x019A
+#define MT6392_DEW_CIPHER_EN 0x019C
+#define MT6392_DEW_CIPHER_RDY 0x019E
+#define MT6392_DEW_CIPHER_MODE 0x01A0
+#define MT6392_DEW_CIPHER_SWRST 0x01A2
+#define MT6392_DEW_RDDMY_NO 0x01A4
+#define MT6392_DEW_RDATA_DLY_SEL 0x01A6
+#define MT6392_CLK_TRIM_CON0 0x01A8
+#define MT6392_BUCK_CON0 0x0200
+#define MT6392_BUCK_CON1 0x0202
+#define MT6392_BUCK_CON2 0x0204
+#define MT6392_BUCK_CON3 0x0206
+#define MT6392_BUCK_CON4 0x0208
+#define MT6392_BUCK_CON5 0x020A
+#define MT6392_VPROC_CON0 0x020C
+#define MT6392_VPROC_CON1 0x020E
+#define MT6392_VPROC_CON2 0x0210
+#define MT6392_VPROC_CON3 0x0212
+#define MT6392_VPROC_CON4 0x0214
+#define MT6392_VPROC_CON5 0x0216
+#define MT6392_VPROC_CON7 0x021A
+#define MT6392_VPROC_CON8 0x021C
+#define MT6392_VPROC_CON9 0x021E
+#define MT6392_VPROC_CON10 0x0220
+#define MT6392_VPROC_CON11 0x0222
+#define MT6392_VPROC_CON12 0x0224
+#define MT6392_VPROC_CON13 0x0226
+#define MT6392_VPROC_CON14 0x0228
+#define MT6392_VPROC_CON15 0x022A
+#define MT6392_VPROC_CON18 0x0230
+#define MT6392_VSYS_CON0 0x0232
+#define MT6392_VSYS_CON1 0x0234
+#define MT6392_VSYS_CON2 0x0236
+#define MT6392_VSYS_CON3 0x0238
+#define MT6392_VSYS_CON4 0x023A
+#define MT6392_VSYS_CON5 0x023C
+#define MT6392_VSYS_CON7 0x0240
+#define MT6392_VSYS_CON8 0x0242
+#define MT6392_VSYS_CON9 0x0244
+#define MT6392_VSYS_CON10 0x0246
+#define MT6392_VSYS_CON11 0x0248
+#define MT6392_VSYS_CON12 0x024A
+#define MT6392_VSYS_CON13 0x024C
+#define MT6392_VSYS_CON14 0x024E
+#define MT6392_VSYS_CON15 0x0250
+#define MT6392_VSYS_CON18 0x0256
+#define MT6392_BUCK_OC_CON0 0x0258
+#define MT6392_BUCK_OC_CON1 0x025A
+#define MT6392_BUCK_OC_CON2 0x025C
+#define MT6392_BUCK_OC_CON3 0x025E
+#define MT6392_BUCK_OC_CON4 0x0260
+#define MT6392_BUCK_OC_VPROC_CON0 0x0262
+#define MT6392_BUCK_OC_VCORE_CON0 0x0264
+#define MT6392_BUCK_OC_VSYS_CON0 0x0266
+#define MT6392_BUCK_ANA_MON_CON0 0x0268
+#define MT6392_BUCK_EFUSE_OC_CON0 0x026A
+#define MT6392_VCORE_CON0 0x0300
+#define MT6392_VCORE_CON1 0x0302
+#define MT6392_VCORE_CON2 0x0304
+#define MT6392_VCORE_CON3 0x0306
+#define MT6392_VCORE_CON4 0x0308
+#define MT6392_VCORE_CON5 0x030A
+#define MT6392_VCORE_CON7 0x030E
+#define MT6392_VCORE_CON8 0x0310
+#define MT6392_VCORE_CON9 0x0312
+#define MT6392_VCORE_CON10 0x0314
+#define MT6392_VCORE_CON11 0x0316
+#define MT6392_VCORE_CON12 0x0318
+#define MT6392_VCORE_CON13 0x031A
+#define MT6392_VCORE_CON14 0x031C
+#define MT6392_VCORE_CON15 0x031E
+#define MT6392_VCORE_CON18 0x0324
+#define MT6392_BUCK_K_CON0 0x032A
+#define MT6392_BUCK_K_CON1 0x032C
+#define MT6392_BUCK_K_CON2 0x032E
+#define MT6392_ANALDO_CON0 0x0400
+#define MT6392_ANALDO_CON1 0x0402
+#define MT6392_ANALDO_CON2 0x0404
+#define MT6392_ANALDO_CON3 0x0406
+#define MT6392_ANALDO_CON4 0x0408
+#define MT6392_ANALDO_CON6 0x040C
+#define MT6392_ANALDO_CON7 0x040E
+#define MT6392_ANALDO_CON8 0x0410
+#define MT6392_ANALDO_CON10 0x0412
+#define MT6392_ANALDO_CON15 0x0414
+#define MT6392_ANALDO_CON16 0x0416
+#define MT6392_ANALDO_CON17 0x0418
+#define MT6392_ANALDO_CON21 0x0420
+#define MT6392_ANALDO_CON22 0x0422
+#define MT6392_ANALDO_CON23 0x0424
+#define MT6392_ANALDO_CON24 0x0426
+#define MT6392_ANALDO_CON25 0x0428
+#define MT6392_ANALDO_CON26 0x042A
+#define MT6392_ANALDO_CON27 0x042C
+#define MT6392_ANALDO_CON28 0x042E
+#define MT6392_ANALDO_CON29 0x0430
+#define MT6392_DIGLDO_CON0 0x0500
+#define MT6392_DIGLDO_CON2 0x0502
+#define MT6392_DIGLDO_CON3 0x0504
+#define MT6392_DIGLDO_CON5 0x0506
+#define MT6392_DIGLDO_CON6 0x0508
+#define MT6392_DIGLDO_CON7 0x050A
+#define MT6392_DIGLDO_CON8 0x050C
+#define MT6392_DIGLDO_CON10 0x0510
+#define MT6392_DIGLDO_CON11 0x0512
+#define MT6392_DIGLDO_CON12 0x0514
+#define MT6392_DIGLDO_CON15 0x051A
+#define MT6392_DIGLDO_CON20 0x0524
+#define MT6392_DIGLDO_CON21 0x0526
+#define MT6392_DIGLDO_CON23 0x0528
+#define MT6392_DIGLDO_CON24 0x052A
+#define MT6392_DIGLDO_CON26 0x052C
+#define MT6392_DIGLDO_CON27 0x052E
+#define MT6392_DIGLDO_CON28 0x0530
+#define MT6392_DIGLDO_CON29 0x0532
+#define MT6392_DIGLDO_CON30 0x0534
+#define MT6392_DIGLDO_CON31 0x0536
+#define MT6392_DIGLDO_CON32 0x0538
+#define MT6392_DIGLDO_CON33 0x053A
+#define MT6392_DIGLDO_CON36 0x0540
+#define MT6392_DIGLDO_CON41 0x0546
+#define MT6392_DIGLDO_CON44 0x054C
+#define MT6392_DIGLDO_CON47 0x0552
+#define MT6392_DIGLDO_CON48 0x0554
+#define MT6392_DIGLDO_CON49 0x0556
+#define MT6392_DIGLDO_CON50 0x0558
+#define MT6392_DIGLDO_CON51 0x055A
+#define MT6392_DIGLDO_CON52 0x055C
+#define MT6392_DIGLDO_CON53 0x055E
+#define MT6392_DIGLDO_CON54 0x0560
+#define MT6392_DIGLDO_CON55 0x0562
+#define MT6392_DIGLDO_CON56 0x0564
+#define MT6392_DIGLDO_CON57 0x0566
+#define MT6392_DIGLDO_CON58 0x0568
+#define MT6392_DIGLDO_CON59 0x056A
+#define MT6392_DIGLDO_CON60 0x056C
+#define MT6392_DIGLDO_CON61 0x056E
+#define MT6392_DIGLDO_CON62 0x0570
+#define MT6392_DIGLDO_CON63 0x0572
+#define MT6392_EFUSE_CON0 0x0600
+#define MT6392_EFUSE_CON1 0x0602
+#define MT6392_EFUSE_CON2 0x0604
+#define MT6392_EFUSE_CON3 0x0606
+#define MT6392_EFUSE_CON4 0x0608
+#define MT6392_EFUSE_CON5 0x060A
+#define MT6392_EFUSE_CON6 0x060C
+#define MT6392_EFUSE_VAL_0_15 0x060E
+#define MT6392_EFUSE_VAL_16_31 0x0610
+#define MT6392_EFUSE_VAL_32_47 0x0612
+#define MT6392_EFUSE_VAL_48_63 0x0614
+#define MT6392_EFUSE_VAL_64_79 0x0616
+#define MT6392_EFUSE_VAL_80_95 0x0618
+#define MT6392_EFUSE_VAL_96_111 0x061A
+#define MT6392_EFUSE_VAL_112_127 0x061C
+#define MT6392_EFUSE_VAL_128_143 0x061E
+#define MT6392_EFUSE_VAL_144_159 0x0620
+#define MT6392_EFUSE_VAL_160_175 0x0622
+#define MT6392_EFUSE_VAL_176_191 0x0624
+#define MT6392_EFUSE_VAL_192_207 0x0626
+#define MT6392_EFUSE_VAL_208_223 0x0628
+#define MT6392_EFUSE_VAL_224_239 0x062A
+#define MT6392_EFUSE_VAL_240_255 0x062C
+#define MT6392_EFUSE_VAL_256_271 0x062E
+#define MT6392_EFUSE_VAL_272_287 0x0630
+#define MT6392_EFUSE_VAL_288_303 0x0632
+#define MT6392_EFUSE_VAL_304_319 0x0634
+#define MT6392_EFUSE_VAL_320_335 0x0636
+#define MT6392_EFUSE_VAL_336_351 0x0638
+#define MT6392_EFUSE_VAL_352_367 0x063A
+#define MT6392_EFUSE_VAL_368_383 0x063C
+#define MT6392_EFUSE_VAL_384_399 0x063E
+#define MT6392_EFUSE_VAL_400_415 0x0640
+#define MT6392_EFUSE_VAL_416_431 0x0642
+#define MT6392_RTC_MIX_CON0 0x0644
+#define MT6392_RTC_MIX_CON1 0x0646
+#define MT6392_EFUSE_VAL_432_447 0x0648
+#define MT6392_EFUSE_VAL_448_463 0x064A
+#define MT6392_EFUSE_VAL_464_479 0x064C
+#define MT6392_EFUSE_VAL_480_495 0x064E
+#define MT6392_EFUSE_VAL_496_511 0x0650
+#define MT6392_EFUSE_DOUT_0_15 0x0652
+#define MT6392_EFUSE_DOUT_16_31 0x0654
+#define MT6392_EFUSE_DOUT_32_47 0x0656
+#define MT6392_EFUSE_DOUT_48_63 0x0658
+#define MT6392_EFUSE_DOUT_64_79 0x065A
+#define MT6392_EFUSE_DOUT_80_95 0x065C
+#define MT6392_EFUSE_DOUT_96_111 0x065E
+#define MT6392_EFUSE_DOUT_112_127 0x0660
+#define MT6392_EFUSE_DOUT_128_143 0x0662
+#define MT6392_EFUSE_DOUT_144_159 0x0664
+#define MT6392_EFUSE_DOUT_160_175 0x0666
+#define MT6392_EFUSE_DOUT_176_191 0x0668
+#define MT6392_EFUSE_DOUT_192_207 0x066A
+#define MT6392_EFUSE_DOUT_208_223 0x066C
+#define MT6392_EFUSE_DOUT_224_239 0x066E
+#define MT6392_EFUSE_DOUT_240_255 0x0670
+#define MT6392_EFUSE_DOUT_256_271 0x0672
+#define MT6392_EFUSE_DOUT_272_287 0x0674
+#define MT6392_EFUSE_DOUT_288_303 0x0676
+#define MT6392_EFUSE_DOUT_304_319 0x0678
+#define MT6392_EFUSE_DOUT_320_335 0x067A
+#define MT6392_EFUSE_DOUT_336_351 0x067C
+#define MT6392_EFUSE_DOUT_352_367 0x067E
+#define MT6392_EFUSE_DOUT_368_383 0x0680
+#define MT6392_EFUSE_DOUT_384_399 0x0682
+#define MT6392_EFUSE_DOUT_400_415 0x0684
+#define MT6392_EFUSE_DOUT_416_431 0x0686
+#define MT6392_EFUSE_DOUT_432_447 0x0688
+#define MT6392_EFUSE_DOUT_448_463 0x068A
+#define MT6392_EFUSE_DOUT_464_479 0x068C
+#define MT6392_EFUSE_DOUT_480_495 0x068E
+#define MT6392_EFUSE_DOUT_496_511 0x0690
+#define MT6392_EFUSE_CON7 0x0692
+#define MT6392_EFUSE_CON8 0x0694
+#define MT6392_EFUSE_CON9 0x0696
+#define MT6392_AUXADC_ADC0 0x0700
+#define MT6392_AUXADC_ADC1 0x0702
+#define MT6392_AUXADC_ADC2 0x0704
+#define MT6392_AUXADC_ADC3 0x0706
+#define MT6392_AUXADC_ADC4 0x0708
+#define MT6392_AUXADC_ADC5 0x070A
+#define MT6392_AUXADC_ADC6 0x070C
+#define MT6392_AUXADC_ADC7 0x070E
+#define MT6392_AUXADC_ADC8 0x0710
+#define MT6392_AUXADC_ADC9 0x0712
+#define MT6392_AUXADC_ADC10 0x0714
+#define MT6392_AUXADC_ADC11 0x0716
+#define MT6392_AUXADC_ADC12 0x0718
+#define MT6392_AUXADC_ADC13 0x071A
+#define MT6392_AUXADC_ADC14 0x071C
+#define MT6392_AUXADC_ADC15 0x071E
+#define MT6392_AUXADC_ADC16 0x0720
+#define MT6392_AUXADC_ADC17 0x0722
+#define MT6392_AUXADC_ADC18 0x0724
+#define MT6392_AUXADC_ADC19 0x0726
+#define MT6392_AUXADC_ADC20 0x0728
+#define MT6392_AUXADC_ADC21 0x072A
+#define MT6392_AUXADC_ADC22 0x072C
+#define MT6392_AUXADC_STA0 0x072E
+#define MT6392_AUXADC_STA1 0x0730
+#define MT6392_AUXADC_RQST0 0x0732
+#define MT6392_AUXADC_RQST0_SET 0x0734
+#define MT6392_AUXADC_RQST0_CLR 0x0736
+#define MT6392_AUXADC_CON0 0x0738
+#define MT6392_AUXADC_CON0_SET 0x073A
+#define MT6392_AUXADC_CON0_CLR 0x073C
+#define MT6392_AUXADC_CON1 0x073E
+#define MT6392_AUXADC_CON2 0x0740
+#define MT6392_AUXADC_CON3 0x0742
+#define MT6392_AUXADC_CON4 0x0744
+#define MT6392_AUXADC_CON5 0x0746
+#define MT6392_AUXADC_CON6 0x0748
+#define MT6392_AUXADC_CON7 0x074A
+#define MT6392_AUXADC_CON8 0x074C
+#define MT6392_AUXADC_CON9 0x074E
+#define MT6392_AUXADC_CON10 0x0750
+#define MT6392_AUXADC_CON11 0x0752
+#define MT6392_AUXADC_CON12 0x0754
+#define MT6392_AUXADC_CON13 0x0756
+#define MT6392_AUXADC_CON14 0x0758
+#define MT6392_AUXADC_CON15 0x075A
+#define MT6392_AUXADC_CON16 0x075C
+#define MT6392_AUXADC_AUTORPT0 0x075E
+#define MT6392_AUXADC_LBAT0 0x0760
+#define MT6392_AUXADC_LBAT1 0x0762
+#define MT6392_AUXADC_LBAT2 0x0764
+#define MT6392_AUXADC_LBAT3 0x0766
+#define MT6392_AUXADC_LBAT4 0x0768
+#define MT6392_AUXADC_LBAT5 0x076A
+#define MT6392_AUXADC_LBAT6 0x076C
+#define MT6392_AUXADC_THR0 0x076E
+#define MT6392_AUXADC_THR1 0x0770
+#define MT6392_AUXADC_THR2 0x0772
+#define MT6392_AUXADC_THR3 0x0774
+#define MT6392_AUXADC_THR4 0x0776
+#define MT6392_AUXADC_THR5 0x0778
+#define MT6392_AUXADC_THR6 0x077A
+#define MT6392_AUXADC_EFUSE0 0x077C
+#define MT6392_AUXADC_EFUSE1 0x077E
+#define MT6392_AUXADC_EFUSE2 0x0780
+#define MT6392_AUXADC_EFUSE3 0x0782
+#define MT6392_AUXADC_EFUSE4 0x0784
+#define MT6392_AUXADC_EFUSE5 0x0786
+#define MT6392_AUXADC_NAG_0 0x0788
+#define MT6392_AUXADC_NAG_1 0x078A
+#define MT6392_AUXADC_NAG_2 0x078C
+#define MT6392_AUXADC_NAG_3 0x078E
+#define MT6392_AUXADC_NAG_4 0x0790
+#define MT6392_AUXADC_NAG_5 0x0792
+#define MT6392_AUXADC_NAG_6 0x0794
+#define MT6392_AUXADC_NAG_7 0x0796
+#define MT6392_AUXADC_NAG_8 0x0798
+#define MT6392_AUXADC_TYPEC_H_1 0x079A
+#define MT6392_AUXADC_TYPEC_H_2 0x079C
+#define MT6392_AUXADC_TYPEC_H_3 0x079E
+#define MT6392_AUXADC_TYPEC_H_4 0x07A0
+#define MT6392_AUXADC_TYPEC_H_5 0x07A2
+#define MT6392_AUXADC_TYPEC_H_6 0x07A4
+#define MT6392_AUXADC_TYPEC_H_7 0x07A6
+#define MT6392_AUXADC_TYPEC_L_1 0x07A8
+#define MT6392_AUXADC_TYPEC_L_2 0x07AA
+#define MT6392_AUXADC_TYPEC_L_3 0x07AC
+#define MT6392_AUXADC_TYPEC_L_4 0x07AE
+#define MT6392_AUXADC_TYPEC_L_5 0x07B0
+#define MT6392_AUXADC_TYPEC_L_6 0x07B2
+#define MT6392_AUXADC_TYPEC_L_7 0x07B4
+#define MT6392_AUXADC_NAG_9 0x07B6
+#define MT6392_TYPE_C_PHY_RG_0 0x0800
+#define MT6392_TYPE_C_PHY_RG_CC_RESERVE_CSR 0x0802
+#define MT6392_TYPE_C_VCMP_CTRL 0x0804
+#define MT6392_TYPE_C_CTRL 0x0806
+#define MT6392_TYPE_C_CC_SW_CTRL 0x080a
+#define MT6392_TYPE_C_CC_VOL_PERIODIC_MEAS_VAL 0x080c
+#define MT6392_TYPE_C_CC_VOL_DEBOUNCE_CNT_VAL 0x080e
+#define MT6392_TYPE_C_DRP_SRC_CNT_VAL_0 0x0810
+#define MT6392_TYPE_C_DRP_SNK_CNT_VAL_0 0x0814
+#define MT6392_TYPE_C_DRP_TRY_CNT_VAL_0 0x0818
+#define MT6392_TYPE_C_CC_SRC_DEFAULT_DAC_VAL 0x0820
+#define MT6392_TYPE_C_CC_SRC_15_DAC_VAL 0x0822
+#define MT6392_TYPE_C_CC_SRC_30_DAC_VAL 0x0824
+#define MT6392_TYPE_C_CC_SNK_DAC_VAL_0 0x0828
+#define MT6392_TYPE_C_CC_SNK_DAC_VAL_1 0x082a
+#define MT6392_TYPE_C_INTR_EN_0 0x0830
+#define MT6392_TYPE_C_INTR_EN_2 0x0834
+#define MT6392_TYPE_C_INTR_0 0x0838
+#define MT6392_TYPE_C_INTR_2 0x083C
+#define MT6392_TYPE_C_CC_STATUS 0x0840
+#define MT6392_TYPE_C_PWR_STATUS 0x0842
+#define MT6392_TYPE_C_PHY_RG_CC1_RESISTENCE_0 0x0844
+#define MT6392_TYPE_C_PHY_RG_CC1_RESISTENCE_1 0x0846
+#define MT6392_TYPE_C_PHY_RG_CC2_RESISTENCE_0 0x0848
+#define MT6392_TYPE_C_PHY_RG_CC2_RESISTENCE_1 0x084a
+#define MT6392_TYPE_C_CC_SW_FORCE_MODE_ENABLE_0 0x0860
+#define MT6392_TYPE_C_CC_SW_FORCE_MODE_VAL_0 0x0864
+#define MT6392_TYPE_C_CC_SW_FORCE_MODE_VAL_1 0x0866
+#define MT6392_TYPE_C_CC_SW_FORCE_MODE_ENABLE_1 0x0868
+#define MT6392_TYPE_C_CC_SW_FORCE_MODE_VAL_2 0x086c
+#define MT6392_TYPE_C_CC_DAC_CALI_CTRL 0x0870
+#define MT6392_TYPE_C_CC_DAC_CALI_RESULT 0x0872
+#define MT6392_TYPE_C_DEBUG_PORT_SELECT_0 0x0880
+#define MT6392_TYPE_C_DEBUG_PORT_SELECT_1 0x0882
+#define MT6392_TYPE_C_DEBUG_MODE_SELECT 0x0884
+#define MT6392_TYPE_C_DEBUG_OUT_READ_0 0x0888
+#define MT6392_TYPE_C_DEBUG_OUT_READ_1 0x088a
+#define MT6392_TYPE_C_SW_DEBUG_PORT_0 0x088c
+#define MT6392_TYPE_C_SW_DEBUG_PORT_1 0x088e
+
+#endif /* __MFD_MT6392_REGISTERS_H__ */
diff --git a/include/linux/mfd/mt6397/core.h b/include/linux/mfd/mt6397/core.h
index 340fc72e22aa..3729a6856c13 100644
--- a/include/linux/mfd/mt6397/core.h
+++ b/include/linux/mfd/mt6397/core.h
@@ -20,6 +20,7 @@ enum chip_id {
MT6359_CHIP_ID = 0x59,
MT6366_CHIP_ID = 0x66,
MT6391_CHIP_ID = 0x91,
+ MT6392_CHIP_ID = 0x92,
MT6397_CHIP_ID = 0x97,
};
--
2.43.0
^ permalink raw reply related
* [PATCH v9 4/9] mfd: mt6397: Use MFD_CELL_* to describe sub-devices
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Luca Leonardo Scorcia, Dmitry Torokhov, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sen Chu, Sean Wang,
Macpaul Lin, Lee Jones, Matthias Brugger,
AngeloGioacchino Del Regno, Liam Girdwood, Mark Brown,
Linus Walleij, Val Packett, Julien Massot, Louis-Alexis Eyraud,
Fabien Parent, Akari Tsuyukusa, Chen Zhong, linux-input,
devicetree, linux-kernel, linux-pm, linux-arm-kernel, linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
Use the MFD_CELL_* macros to describe sub-devices. No functional changes.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
---
drivers/mfd/mt6397-core.c | 197 ++++++++++++--------------------------
1 file changed, 63 insertions(+), 134 deletions(-)
diff --git a/drivers/mfd/mt6397-core.c b/drivers/mfd/mt6397-core.c
index 1bdacda9a933..ccd97d66d7f1 100644
--- a/drivers/mfd/mt6397-core.c
+++ b/drivers/mfd/mt6397-core.c
@@ -124,159 +124,88 @@ static const struct resource mt6323_pwrc_resources[] = {
};
static const struct mfd_cell mt6323_devs[] = {
- {
- .name = "mt6323-rtc",
- .num_resources = ARRAY_SIZE(mt6323_rtc_resources),
- .resources = mt6323_rtc_resources,
- .of_compatible = "mediatek,mt6323-rtc",
- }, {
- .name = "mt6323-regulator",
- .of_compatible = "mediatek,mt6323-regulator"
- }, {
- .name = "mt6323-led",
- .of_compatible = "mediatek,mt6323-led"
- }, {
- .name = "mt6323-keys",
- .num_resources = ARRAY_SIZE(mt6323_keys_resources),
- .resources = mt6323_keys_resources,
- .of_compatible = "mediatek,mt6323-keys"
- }, {
- .name = "mt6323-pwrc",
- .num_resources = ARRAY_SIZE(mt6323_pwrc_resources),
- .resources = mt6323_pwrc_resources,
- .of_compatible = "mediatek,mt6323-pwrc"
- },
+ MFD_CELL_OF("mt6323-rtc", mt6323_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6323-rtc"),
+ MFD_CELL_OF("mt6323-regulator", NULL, NULL, 0, 0,
+ "mediatek,mt6323-regulator"),
+ MFD_CELL_OF("mt6323-led", NULL, NULL, 0, 0,
+ "mediatek,mt6323-led"),
+ MFD_CELL_OF("mt6323-keys", mt6323_keys_resources, NULL, 0, 0,
+ "mediatek,mt6323-keys"),
+ MFD_CELL_OF("mt6323-pwrc", mt6323_pwrc_resources, NULL, 0, 0,
+ "mediatek,mt6323-pwrc"),
};
static const struct mfd_cell mt6328_devs[] = {
- {
- .name = "mt6328-regulator",
- .of_compatible = "mediatek,mt6328-regulator"
- }, {
- .name = "mt6328-keys",
- .num_resources = ARRAY_SIZE(mt6328_keys_resources),
- .resources = mt6328_keys_resources,
- .of_compatible = "mediatek,mt6328-keys"
- },
+ MFD_CELL_OF("mt6328-regulator", NULL, NULL, 0, 0,
+ "mediatek,mt6328-regulator"),
+ MFD_CELL_OF("mt6328-keys", mt6328_keys_resources, NULL, 0, 0,
+ "mediatek,mt6328-keys"),
};
static const struct mfd_cell mt6357_devs[] = {
- {
- .name = "mt6359-auxadc",
- .of_compatible = "mediatek,mt6357-auxadc"
- }, {
- .name = "mt6357-regulator",
- }, {
- .name = "mt6357-rtc",
- .num_resources = ARRAY_SIZE(mt6357_rtc_resources),
- .resources = mt6357_rtc_resources,
- .of_compatible = "mediatek,mt6357-rtc",
- }, {
- .name = "mt6357-sound",
- .of_compatible = "mediatek,mt6357-sound"
- }, {
- .name = "mt6357-keys",
- .num_resources = ARRAY_SIZE(mt6357_keys_resources),
- .resources = mt6357_keys_resources,
- .of_compatible = "mediatek,mt6357-keys"
- },
+ MFD_CELL_OF("mt6359-auxadc", NULL, NULL, 0, 0,
+ "mediatek,mt6357-auxadc"),
+ MFD_CELL_NAME("mt6357-regulator"),
+ MFD_CELL_OF("mt6357-rtc", mt6357_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6357-rtc"),
+ MFD_CELL_OF("mt6357-sound", NULL, NULL, 0, 0,
+ "mediatek,mt6357-sound"),
+ MFD_CELL_OF("mt6357-keys", mt6357_keys_resources, NULL, 0, 0,
+ "mediatek,mt6357-keys"),
};
/* MT6331 is always used in combination with MT6332 */
static const struct mfd_cell mt6331_mt6332_devs[] = {
- {
- .name = "mt6331-rtc",
- .num_resources = ARRAY_SIZE(mt6331_rtc_resources),
- .resources = mt6331_rtc_resources,
- .of_compatible = "mediatek,mt6331-rtc",
- }, {
- .name = "mt6331-regulator",
- .of_compatible = "mediatek,mt6331-regulator"
- }, {
- .name = "mt6332-regulator",
- .of_compatible = "mediatek,mt6332-regulator"
- }, {
- .name = "mt6331-keys",
- .num_resources = ARRAY_SIZE(mt6331_keys_resources),
- .resources = mt6331_keys_resources,
- .of_compatible = "mediatek,mt6331-keys"
- },
+ MFD_CELL_OF("mt6331-rtc", mt6331_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6331-rtc"),
+ MFD_CELL_OF("mt6331-regulator", NULL, NULL, 0, 0,
+ "mediatek,mt6331-regulator"),
+ MFD_CELL_OF("mt6332-regulator", NULL, NULL, 0, 0,
+ "mediatek,mt6332-regulator"),
+ MFD_CELL_OF("mt6331-keys", mt6331_keys_resources, NULL, 0, 0,
+ "mediatek,mt6331-keys"),
};
static const struct mfd_cell mt6358_devs[] = {
- {
- .name = "mt6359-auxadc",
- .of_compatible = "mediatek,mt6358-auxadc"
- }, {
- .name = "mt6358-regulator",
- .of_compatible = "mediatek,mt6358-regulator"
- }, {
- .name = "mt6358-rtc",
- .num_resources = ARRAY_SIZE(mt6358_rtc_resources),
- .resources = mt6358_rtc_resources,
- .of_compatible = "mediatek,mt6358-rtc",
- }, {
- .name = "mt6358-sound",
- .of_compatible = "mediatek,mt6358-sound"
- }, {
- .name = "mt6358-keys",
- .num_resources = ARRAY_SIZE(mt6358_keys_resources),
- .resources = mt6358_keys_resources,
- .of_compatible = "mediatek,mt6358-keys"
- },
+ MFD_CELL_OF("mt6359-auxadc", NULL, NULL, 0, 0,
+ "mediatek,mt6358-auxadc"),
+ MFD_CELL_OF("mt6358-regulator", NULL, NULL, 0, 0,
+ "mediatek,mt6358-regulator"),
+ MFD_CELL_OF("mt6358-rtc", mt6358_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6358-rtc"),
+ MFD_CELL_OF("mt6358-sound", NULL, NULL, 0, 0,
+ "mediatek,mt6358-sound"),
+ MFD_CELL_OF("mt6358-keys", mt6358_keys_resources, NULL, 0, 0,
+ "mediatek,mt6358-keys"),
};
static const struct mfd_cell mt6359_devs[] = {
- {
- .name = "mt6359-auxadc",
- .of_compatible = "mediatek,mt6359-auxadc"
- },
- { .name = "mt6359-regulator", },
- {
- .name = "mt6359-rtc",
- .num_resources = ARRAY_SIZE(mt6358_rtc_resources),
- .resources = mt6358_rtc_resources,
- .of_compatible = "mediatek,mt6358-rtc",
- },
- { .name = "mt6359-sound", },
- {
- .name = "mt6359-keys",
- .num_resources = ARRAY_SIZE(mt6359_keys_resources),
- .resources = mt6359_keys_resources,
- .of_compatible = "mediatek,mt6359-keys"
- },
- {
- .name = "mt6359-accdet",
- .of_compatible = "mediatek,mt6359-accdet",
- .num_resources = ARRAY_SIZE(mt6359_accdet_resources),
- .resources = mt6359_accdet_resources,
- },
+ MFD_CELL_OF("mt6359-auxadc", NULL, NULL, 0, 0,
+ "mediatek,mt6359-auxadc"),
+ MFD_CELL_NAME("mt6359-regulator"),
+ MFD_CELL_OF("mt6359-rtc", mt6358_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6358-rtc"),
+ MFD_CELL_NAME("mt6359-sound"),
+ MFD_CELL_OF("mt6359-keys", mt6359_keys_resources, NULL, 0, 0,
+ "mediatek,mt6359-keys"),
+ MFD_CELL_OF("mt6359-accdet", mt6359_accdet_resources, NULL, 0, 0,
+ "mediatek,mt6359-accdet"),
};
static const struct mfd_cell mt6397_devs[] = {
- {
- .name = "mt6397-rtc",
- .num_resources = ARRAY_SIZE(mt6397_rtc_resources),
- .resources = mt6397_rtc_resources,
- .of_compatible = "mediatek,mt6397-rtc",
- }, {
- .name = "mt6397-regulator",
- .of_compatible = "mediatek,mt6397-regulator",
- }, {
- .name = "mt6397-codec",
- .of_compatible = "mediatek,mt6397-codec",
- }, {
- .name = "mt6397-clk",
- .of_compatible = "mediatek,mt6397-clk",
- }, {
- .name = "mt6397-pinctrl",
- .of_compatible = "mediatek,mt6397-pinctrl",
- }, {
- .name = "mt6397-keys",
- .num_resources = ARRAY_SIZE(mt6397_keys_resources),
- .resources = mt6397_keys_resources,
- .of_compatible = "mediatek,mt6397-keys"
- }
+ MFD_CELL_OF("mt6397-rtc", mt6397_rtc_resources, NULL, 0, 0,
+ "mediatek,mt6397-rtc"),
+ MFD_CELL_OF("mt6397-regulator", NULL, NULL, 0, 0,
+ "mediatek,mt6397-regulator"),
+ MFD_CELL_OF("mt6397-codec", NULL, NULL, 0, 0,
+ "mediatek,mt6397-codec"),
+ MFD_CELL_OF("mt6397-clk", NULL, NULL, 0, 0,
+ "mediatek,mt6397-clk"),
+ MFD_CELL_OF("mt6397-pinctrl", NULL, NULL, 0, 0,
+ "mediatek,mt6397-pinctrl"),
+ MFD_CELL_OF("mt6397-keys", mt6397_keys_resources, NULL, 0, 0,
+ "mediatek,mt6397-keys"),
};
struct chip_data {
--
2.43.0
^ permalink raw reply related
* [PATCH v9 3/9] regulator: dt-bindings: Add MediaTek MT6392 PMIC
From: Luca Leonardo Scorcia @ 2026-06-21 8:13 UTC (permalink / raw)
To: linux-mediatek
Cc: Luca Leonardo Scorcia, Dmitry Torokhov, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Sen Chu, Sean Wang,
Macpaul Lin, Lee Jones, Matthias Brugger,
AngeloGioacchino Del Regno, Liam Girdwood, Mark Brown,
Linus Walleij, Julien Massot, Louis-Alexis Eyraud, Val Packett,
Fabien Parent, Akari Tsuyukusa, Chen Zhong, linux-input,
devicetree, linux-kernel, linux-pm, linux-arm-kernel, linux-gpio
In-Reply-To: <20260621081634.467858-1-l.scorcia@gmail.com>
Add bindings for the regulators found in the MediaTek MT6392 PMIC,
usually found in board designs using the MediaTek MT8516/MT8167 SoCs.
Signed-off-by: Luca Leonardo Scorcia <l.scorcia@gmail.com>
---
.../regulator/mediatek,mt6392-regulator.yaml | 112 ++++++++++++++++++
.../regulator/mediatek,mt6392-regulator.h | 23 ++++
2 files changed, 135 insertions(+)
create mode 100644 Documentation/devicetree/bindings/regulator/mediatek,mt6392-regulator.yaml
create mode 100644 include/dt-bindings/regulator/mediatek,mt6392-regulator.h
diff --git a/Documentation/devicetree/bindings/regulator/mediatek,mt6392-regulator.yaml b/Documentation/devicetree/bindings/regulator/mediatek,mt6392-regulator.yaml
new file mode 100644
index 000000000000..d74721d8f2ff
--- /dev/null
+++ b/Documentation/devicetree/bindings/regulator/mediatek,mt6392-regulator.yaml
@@ -0,0 +1,112 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/mediatek,mt6392-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: MediaTek MT6392 regulator
+
+maintainers:
+ - Luca Leonardo Scorcia <l.scorcia@gmail.com>
+
+description:
+ MT6392 is a power management system chip containing three buck converters and
+ 23 LDOs. All voltage regulators provided by the PMIC are described as
+ sub-nodes of this node.
+
+properties:
+ compatible:
+ items:
+ - const: mediatek,mt6392-regulator
+
+ vproc-supply:
+ description: Supply for buck regulator vproc
+ vcore-supply:
+ description: Supply for buck regulator vcore
+ vsys-supply:
+ description: Supply for buck regulator vsys
+ avddldo-supply:
+ description:
+ Supply for AVDD LDOs (vm, vio18, vcn18, vcamd, vcamio). According to the data sheet
+ this is an internal supply derived from vsys.
+ ldo1-supply:
+ description: Supply for LDOs group 1 (vaud28, vxo22, vaud22, vadc18, vcama, vrtc)
+ ldo2-supply:
+ description: Supply for LDOs group 2 (vcn35, vio28, vmc, vmch, vefuse, vdig18)
+ ldo3-supply:
+ description: Supply for LDOs group 3 (vusb, vemc3v3, vcamaf, vgp1, vgp2, vm25)
+
+patternProperties:
+ "^v(core|proc|sys)$":
+ description: Buck regulators
+ type: object
+ $ref: regulator.yaml#
+ unevaluatedProperties: false
+ properties:
+ regulator-allowed-modes:
+ description:
+ BUCK regulators can set regulator-allowed-modes to values specified in
+ dt-bindings/regulator/mediatek,mt6392-regulator.h
+ items:
+ enum: [0, 1]
+ minItems: 1
+ maxItems: 2
+ regulator-initial-mode:
+ description:
+ BUCK regulators can set regulator-initial-mode to values specified in
+ dt-bindings/regulator/mediatek,mt6392-regulator.h
+ enum: [0, 1]
+
+ "^v(adc18|camio|cn18|io18|xo22|m25|aud28|io28|usb)$":
+ description: LDOs with fixed output and mode setting
+ type: object
+ $ref: regulator.yaml#
+ unevaluatedProperties: false
+ properties:
+ regulator-allowed-modes:
+ description:
+ LDO regulators can set regulator-allowed-modes to values specified in
+ dt-bindings/regulator/mediatek,mt6392-regulator.h
+ items:
+ enum: [0, 2]
+ minItems: 1
+ maxItems: 2
+ regulator-initial-mode:
+ description:
+ LDO regulators can set regulator-initial-mode to values specified in
+ dt-bindings/regulator/mediatek,mt6392-regulator.h
+ enum: [0, 2]
+
+ "^v(cama|dig18|rtc)$":
+ description: LDOs with fixed output without mode setting
+ type: object
+ $ref: regulator.yaml#
+ unevaluatedProperties: false
+ properties:
+ regulator-allowed-modes: false
+ regulator-initial-mode: false
+
+ "^v(aud22|camaf|camd|cn35|efuse|emc3v3|gp1|gp2|m|mc|mch)$":
+ description: LDOs with adjustable output and mode setting
+ type: object
+ $ref: regulator.yaml#
+ unevaluatedProperties: false
+ properties:
+ regulator-allowed-modes:
+ description:
+ LDO regulators can set regulator-allowed-modes to values specified in
+ dt-bindings/regulator/mediatek,mt6392-regulator.h
+ items:
+ enum: [0, 2]
+ minItems: 1
+ maxItems: 2
+ regulator-initial-mode:
+ description:
+ LDO regulators can set regulator-initial-mode to values specified in
+ dt-bindings/regulator/mediatek,mt6392-regulator.h
+ enum: [0, 2]
+
+required:
+ - compatible
+
+additionalProperties: false
diff --git a/include/dt-bindings/regulator/mediatek,mt6392-regulator.h b/include/dt-bindings/regulator/mediatek,mt6392-regulator.h
new file mode 100644
index 000000000000..2e1f41e0ebfe
--- /dev/null
+++ b/include/dt-bindings/regulator/mediatek,mt6392-regulator.h
@@ -0,0 +1,23 @@
+/* SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) */
+
+#ifndef _DT_BINDINGS_REGULATOR_MEDIATEK_MT6392_H_
+#define _DT_BINDINGS_REGULATOR_MEDIATEK_MT6392_H_
+
+/*
+ * Buck mode constants which may be used in devicetree properties (eg.
+ * regulator-initial-mode, regulator-allowed-modes).
+ * See the manufacturer's datasheet for more information on these modes.
+ */
+
+#define MT6392_REGULATOR_MODE_NORMAL 0
+#define MT6392_BUCK_MODE_FORCE_PWM 1
+
+/*
+ * LDO mode constants which may be used in devicetree properties (eg.
+ * regulator-initial-mode, regulator-allowed-modes).
+ * See the manufacturer's datasheet for more information on these modes.
+ */
+
+#define MT6392_LDO_MODE_LP 2
+
+#endif
--
2.43.0
^ permalink raw reply related
page: next (older) | prev (newer) | latest
- recent:[subjects (threaded)|topics (new)|topics (active)]
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox