From: Bjorn Andersson <bjorn.andersson@linaro.org>
To: Paolo Pisati <p.pisati@gmail.com>
Cc: Andy Gross <agross@kernel.org>,
Amit Pundir <amit.pundir@linaro.org>,
Manu Gautam <mgautam@codeaurora.org>,
linux-arm-msm@vger.kernel.org
Subject: Re: [PATCH 3/6] Revert "phy: qcom-qmp: Correct ready status, again"
Date: Thu, 5 Dec 2019 23:07:05 -0800 [thread overview]
Message-ID: <20191206070705.GD289401@yoga> (raw)
In-Reply-To: <20191205161505.15295-7-p.pisati@gmail.com>
On Thu 05 Dec 08:15 PST 2019, Paolo Pisati wrote:
> This reverts commit 14ced7e3a1ae9bed7051df3718c8c7b583854a5c.
>
> Signed-off-by: Paolo Pisati <p.pisati@gmail.com>
Thanks for the patch Paolo, but reverting this commit means we're
checking for the wrong status bit and thereby relies on timing of that
bit having an appropriate value again.
The problem at hand seems to be that some resources are missing while
trying to initialize the PHY, which causes it to not become ready. I saw
the same problem when bringing up PCIe on SDM845, but failed to validate
MSM8996, as this was not booting since mid-summer.
I verified that this is the case by applying:
https://lore.kernel.org/linux-arm-msm/20191107000917.1092409-4-bjorn.andersson@linaro.org/
Regards,
Bjorn
> ---
> drivers/phy/qualcomm/phy-qcom-qmp.c | 33 +++++++++++++++++----------------
> 1 file changed, 17 insertions(+), 16 deletions(-)
>
> diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
> index 39e8deb..e7b8283 100644
> --- a/drivers/phy/qualcomm/phy-qcom-qmp.c
> +++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
> @@ -35,7 +35,7 @@
> #define PLL_READY_GATE_EN BIT(3)
> /* QPHY_PCS_STATUS bit */
> #define PHYSTATUS BIT(6)
> -/* QPHY_PCS_READY_STATUS & QPHY_COM_PCS_READY_STATUS bit */
> +/* QPHY_COM_PCS_READY_STATUS bit */
> #define PCS_READY BIT(0)
>
> /* QPHY_V3_DP_COM_RESET_OVRD_CTRL register bits */
> @@ -115,7 +115,6 @@ enum qphy_reg_layout {
> QPHY_SW_RESET,
> QPHY_START_CTRL,
> QPHY_PCS_READY_STATUS,
> - QPHY_PCS_STATUS,
> QPHY_PCS_AUTONOMOUS_MODE_CTRL,
> QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR,
> QPHY_PCS_LFPS_RXTERM_IRQ_STATUS,
> @@ -134,7 +133,7 @@ static const unsigned int pciephy_regs_layout[] = {
> [QPHY_FLL_MAN_CODE] = 0xd4,
> [QPHY_SW_RESET] = 0x00,
> [QPHY_START_CTRL] = 0x08,
> - [QPHY_PCS_STATUS] = 0x174,
> + [QPHY_PCS_READY_STATUS] = 0x174,
> };
>
> static const unsigned int usb3phy_regs_layout[] = {
> @@ -145,7 +144,7 @@ static const unsigned int usb3phy_regs_layout[] = {
> [QPHY_FLL_MAN_CODE] = 0xd0,
> [QPHY_SW_RESET] = 0x00,
> [QPHY_START_CTRL] = 0x08,
> - [QPHY_PCS_STATUS] = 0x17c,
> + [QPHY_PCS_READY_STATUS] = 0x17c,
> [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d4,
> [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0d8,
> [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x178,
> @@ -154,7 +153,7 @@ static const unsigned int usb3phy_regs_layout[] = {
> static const unsigned int qmp_v3_usb3phy_regs_layout[] = {
> [QPHY_SW_RESET] = 0x00,
> [QPHY_START_CTRL] = 0x08,
> - [QPHY_PCS_STATUS] = 0x174,
> + [QPHY_PCS_READY_STATUS] = 0x174,
> [QPHY_PCS_AUTONOMOUS_MODE_CTRL] = 0x0d8,
> [QPHY_PCS_LFPS_RXTERM_IRQ_CLEAR] = 0x0dc,
> [QPHY_PCS_LFPS_RXTERM_IRQ_STATUS] = 0x170,
> @@ -912,6 +911,7 @@ struct qmp_phy_cfg {
>
> unsigned int start_ctrl;
> unsigned int pwrdn_ctrl;
> + unsigned int mask_pcs_ready;
> unsigned int mask_com_pcs_ready;
>
> /* true, if PHY has a separate PHY_COM control block */
> @@ -1074,6 +1074,7 @@ static const struct qmp_phy_cfg msm8996_pciephy_cfg = {
>
> .start_ctrl = PCS_START | PLL_READY_GATE_EN,
> .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
> + .mask_pcs_ready = PHYSTATUS,
> .mask_com_pcs_ready = PCS_READY,
>
> .has_phy_com_ctrl = true,
> @@ -1105,6 +1106,7 @@ static const struct qmp_phy_cfg msm8996_usb3phy_cfg = {
>
> .start_ctrl = SERDES_START | PCS_START,
> .pwrdn_ctrl = SW_PWRDN,
> + .mask_pcs_ready = PHYSTATUS,
> };
>
> /* list of resets */
> @@ -1134,6 +1136,7 @@ static const struct qmp_phy_cfg ipq8074_pciephy_cfg = {
>
> .start_ctrl = SERDES_START | PCS_START,
> .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
> + .mask_pcs_ready = PHYSTATUS,
>
> .has_phy_com_ctrl = false,
> .has_lane_rst = false,
> @@ -1164,6 +1167,7 @@ static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
>
> .start_ctrl = SERDES_START | PCS_START,
> .pwrdn_ctrl = SW_PWRDN,
> + .mask_pcs_ready = PHYSTATUS,
>
> .has_pwrdn_delay = true,
> .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
> @@ -1195,6 +1199,7 @@ static const struct qmp_phy_cfg qmp_v3_usb3_uniphy_cfg = {
>
> .start_ctrl = SERDES_START | PCS_START,
> .pwrdn_ctrl = SW_PWRDN,
> + .mask_pcs_ready = PHYSTATUS,
>
> .has_pwrdn_delay = true,
> .pwrdn_delay_min = POWER_DOWN_DELAY_US_MIN,
> @@ -1221,6 +1226,7 @@ static const struct qmp_phy_cfg sdm845_ufsphy_cfg = {
>
> .start_ctrl = SERDES_START,
> .pwrdn_ctrl = SW_PWRDN,
> + .mask_pcs_ready = PCS_READY,
>
> .is_dual_lane_phy = true,
> .no_pcs_sw_reset = true,
> @@ -1248,6 +1254,7 @@ static const struct qmp_phy_cfg msm8998_pciephy_cfg = {
>
> .start_ctrl = SERDES_START | PCS_START,
> .pwrdn_ctrl = SW_PWRDN | REFCLK_DRV_DSBL,
> + .mask_pcs_ready = PHYSTATUS,
> };
>
> static const struct qmp_phy_cfg msm8998_usb3phy_cfg = {
> @@ -1272,6 +1279,7 @@ static const struct qmp_phy_cfg msm8998_usb3phy_cfg = {
>
> .start_ctrl = SERDES_START | PCS_START,
> .pwrdn_ctrl = SW_PWRDN,
> + .mask_pcs_ready = PHYSTATUS,
>
> .is_dual_lane_phy = true,
> };
> @@ -1449,7 +1457,7 @@ static int qcom_qmp_phy_enable(struct phy *phy)
> void __iomem *pcs = qphy->pcs;
> void __iomem *dp_com = qmp->dp_com;
> void __iomem *status;
> - unsigned int mask, val, ready;
> + unsigned int mask, val;
> int ret;
>
> dev_vdbg(qmp->dev, "Initializing QMP phy\n");
> @@ -1537,17 +1545,10 @@ static int qcom_qmp_phy_enable(struct phy *phy)
> /* start SerDes and Phy-Coding-Sublayer */
> qphy_setbits(pcs, cfg->regs[QPHY_START_CTRL], cfg->start_ctrl);
>
> - if (cfg->type == PHY_TYPE_UFS) {
> - status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
> - mask = PCS_READY;
> - ready = PCS_READY;
> - } else {
> - status = pcs + cfg->regs[QPHY_PCS_STATUS];
> - mask = PHYSTATUS;
> - ready = 0;
> - }
> + status = pcs + cfg->regs[QPHY_PCS_READY_STATUS];
> + mask = cfg->mask_pcs_ready;
>
> - ret = readl_poll_timeout(status, val, (val & mask) == ready, 10,
> + ret = readl_poll_timeout(status, val, val & mask, 10,
> PHY_INIT_COMPLETE_TIMEOUT);
> if (ret) {
> dev_err(qmp->dev, "phy initialization timed-out\n");
> --
> 2.7.4
>
next prev parent reply other threads:[~2019-12-06 7:07 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-05 16:14 [PATCH 0/6] msm8996: db820c: Fix mmc/ufs and get 5.4 to userspace Paolo Pisati
2019-12-05 16:15 ` [PATCH 1/6] clk: qcom: Drop gcc_aggre1_pnoc_ahb_clk clock Paolo Pisati
2019-12-09 15:05 ` [PATCH v2] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core Paolo Pisati
2019-12-09 15:14 ` [PATCH v2] clk: qcom: Drop gcc_aggre1_pnoc_ahb_clk clock Paolo Pisati
2019-12-09 15:14 ` [PATCH 1/6] " Amit Pundir
2019-12-05 16:15 ` [PATCH 2/6] arm64: dts: qcom: msm8996: Disable USB2 PHY suspend by core Paolo Pisati
2019-12-07 20:44 ` Bjorn Andersson
2019-12-09 15:15 ` [PATCH v2] " Paolo Pisati
2019-12-05 16:15 ` [PATCH 4/6] arm64: defconfig: PHY_QCOM_QMP=y Paolo Pisati
2019-12-05 16:15 ` [PATCH 5/6] arm64: defconfig: PHY_QCOM_QUSB2=y Paolo Pisati
2019-12-05 16:15 ` [PATCH 6/6] arm64: defconfig: PHY_QCOM_UFS=y Paolo Pisati
2019-12-05 16:15 ` [PATCH 3/6] Revert "phy: qcom-qmp: Correct ready status, again" Paolo Pisati
2019-12-06 7:07 ` Bjorn Andersson [this message]
2019-12-06 10:00 ` Paolo Pisati
2019-12-06 19:51 ` Bjorn Andersson
2019-12-07 18:39 ` Bjorn Andersson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20191206070705.GD289401@yoga \
--to=bjorn.andersson@linaro.org \
--cc=agross@kernel.org \
--cc=amit.pundir@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=mgautam@codeaurora.org \
--cc=p.pisati@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox