[PATCH AUTOSEL 4.19 009/172] clk: qcom: msm8916: Fix the address location of pll->config_reg

[PATCH AUTOSEL 4.19 009/172] clk: qcom: msm8916: Fix the address location of pll->config_reg

[Sasha Levin]

From: Bryan O'Donoghue <bryan.odonoghue@linaro.org>

[ Upstream commit f47ab3c2f5338828a67e89d5f688d2cef9605245 ]

During the process of debugging a processor derived from the msm8916 which
we found the new processor was not starting one of its PLLs.

After tracing the addresses and writes that downstream was doing and
comparing to upstream it became obvious that we were writing to a different
register location than downstream when trying to configure the PLL.

This error is also present in upstream msm8916.

As an example clk-pll.c::clk_pll_recalc_rate wants to write to
pll->config_reg updating the bit-field POST_DIV_RATIO. That bit-field is
defined in PLL_USER_CTL not in PLL_CONFIG_CTL. Taking the BIMC PLL as an
example

lm80-p0436-13_c_qc_snapdragon_410_processor_hrd.pdf

0x01823010 GCC_BIMC_PLL_USER_CTL
0x01823014 GCC_BIMC_PLL_CONFIG_CTL

This pattern is repeated for gpll0, gpll1, gpll2 and bimc_pll.

This error is likely not apparent since the bootloader will already have
initialized these PLLs.

This patch corrects the location of config_reg from PLL_CONFIG_CTL to
PLL_USER_CTL for all relevant PLLs on msm8916.

Fixes commit 3966fab8b6ab ("clk: qcom: Add MSM8916 Global Clock Controller support")

Cc: Georgi Djakov <georgi.djakov@linaro.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Link: https://lkml.kernel.org/r/20200329124116.4185447-1-bryan.odonoghue@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/clk/qcom/gcc-msm8916.c | 8 ++++----
 1 file changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/qcom/gcc-msm8916.c b/drivers/clk/qcom/gcc-msm8916.c
index ac2b0aa1e8b5..03e0ade7a6f3 100644
--- a/drivers/clk/qcom/gcc-msm8916.c
+++ b/drivers/clk/qcom/gcc-msm8916.c
@@ -268,7 +268,7 @@ static struct clk_pll gpll0 = {
 	.l_reg = 0x21004,
 	.m_reg = 0x21008,
 	.n_reg = 0x2100c,
-	.config_reg = 0x21014,
+	.config_reg = 0x21010,
 	.mode_reg = 0x21000,
 	.status_reg = 0x2101c,
 	.status_bit = 17,
@@ -295,7 +295,7 @@ static struct clk_pll gpll1 = {
 	.l_reg = 0x20004,
 	.m_reg = 0x20008,
 	.n_reg = 0x2000c,
-	.config_reg = 0x20014,
+	.config_reg = 0x20010,
 	.mode_reg = 0x20000,
 	.status_reg = 0x2001c,
 	.status_bit = 17,
@@ -322,7 +322,7 @@ static struct clk_pll gpll2 = {
 	.l_reg = 0x4a004,
 	.m_reg = 0x4a008,
 	.n_reg = 0x4a00c,
-	.config_reg = 0x4a014,
+	.config_reg = 0x4a010,
 	.mode_reg = 0x4a000,
 	.status_reg = 0x4a01c,
 	.status_bit = 17,
@@ -349,7 +349,7 @@ static struct clk_pll bimc_pll = {
 	.l_reg = 0x23004,
 	.m_reg = 0x23008,
 	.n_reg = 0x2300c,
-	.config_reg = 0x23014,
+	.config_reg = 0x23010,
 	.mode_reg = 0x23000,
 	.status_reg = 0x2301c,
 	.status_bit = 17,
-- 
2.25.1

[PATCH AUTOSEL 4.19 061/172] firmware: qcom_scm: fix bogous abuse of dma-direct internals

[Sasha Levin]

From: Christoph Hellwig <hch@lst.de>

[ Upstream commit 459b1f86f1cba7de813fbc335df476c111feec22 ]

As far as the device is concerned the dma address is the physical
address.  There is no need to convert it to a physical address,
especially not using dma-direct internals that are not available
to drivers and which will interact badly with IOMMUs.  Last but not
least the commit introducing it claimed to just fix a type issue,
but actually changed behavior.

Fixes: 6e37ccf78a532 ("firmware: qcom_scm: Use proper types for dma mappings")
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20200414123136.441454-1-hch@lst.de
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/firmware/qcom_scm.c | 9 +++------
 1 file changed, 3 insertions(+), 6 deletions(-)

diff --git a/drivers/firmware/qcom_scm.c b/drivers/firmware/qcom_scm.c
index 98c987188835..513908a0c262 100644
--- a/drivers/firmware/qcom_scm.c
+++ b/drivers/firmware/qcom_scm.c
@@ -18,7 +18,6 @@
 #include <linux/init.h>
 #include <linux/cpumask.h>
 #include <linux/export.h>
-#include <linux/dma-direct.h>
 #include <linux/dma-mapping.h>
 #include <linux/module.h>
 #include <linux/types.h>
@@ -449,8 +448,7 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,
 	struct qcom_scm_mem_map_info *mem_to_map;
 	phys_addr_t mem_to_map_phys;
 	phys_addr_t dest_phys;
-	phys_addr_t ptr_phys;
-	dma_addr_t ptr_dma;
+	dma_addr_t ptr_phys;
 	size_t mem_to_map_sz;
 	size_t dest_sz;
 	size_t src_sz;
@@ -468,10 +466,9 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,
 	ptr_sz = ALIGN(src_sz, SZ_64) + ALIGN(mem_to_map_sz, SZ_64) +
 			ALIGN(dest_sz, SZ_64);
 
-	ptr = dma_alloc_coherent(__scm->dev, ptr_sz, &ptr_dma, GFP_KERNEL);
+	ptr = dma_alloc_coherent(__scm->dev, ptr_sz, &ptr_phys, GFP_KERNEL);
 	if (!ptr)
 		return -ENOMEM;
-	ptr_phys = dma_to_phys(__scm->dev, ptr_dma);
 
 	/* Fill source vmid detail */
 	src = ptr;
@@ -501,7 +498,7 @@ int qcom_scm_assign_mem(phys_addr_t mem_addr, size_t mem_sz,
 
 	ret = __qcom_scm_assign_mem(__scm->dev, mem_to_map_phys, mem_to_map_sz,
 				    ptr_phys, src_sz, dest_phys, dest_sz);
-	dma_free_coherent(__scm->dev, ptr_sz, ptr, ptr_dma);
+	dma_free_coherent(__scm->dev, ptr_sz, ptr, ptr_phys);
 	if (ret) {
 		dev_err(__scm->dev,
 			"Assign memory protection call failed %d.\n", ret);
-- 
2.25.1

[PATCH AUTOSEL 4.19 069/172] slimbus: ngd: get drvdata from correct device

[Sasha Levin]

From: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>

[ Upstream commit b58c663059b484f7ff547d076a34cf6d7a302e56 ]

Get drvdata directly from parent instead of ngd dev, as ngd
dev can probe defer and previously set drvdata will become null.

Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20200417093618.7929-1-srinivas.kandagatla@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/slimbus/qcom-ngd-ctrl.c | 4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/drivers/slimbus/qcom-ngd-ctrl.c b/drivers/slimbus/qcom-ngd-ctrl.c
index 9221ba7b7863..f40ac8dcb081 100644
--- a/drivers/slimbus/qcom-ngd-ctrl.c
+++ b/drivers/slimbus/qcom-ngd-ctrl.c
@@ -1350,7 +1350,6 @@ static int of_qcom_slim_ngd_register(struct device *parent,
 		ngd->pdev->driver_override = QCOM_SLIM_NGD_DRV_NAME;
 		ngd->pdev->dev.of_node = node;
 		ctrl->ngd = ngd;
-		platform_set_drvdata(ngd->pdev, ctrl);
 
 		platform_device_add(ngd->pdev);
 		ngd->base = ctrl->base + ngd->id * data->offset +
@@ -1365,12 +1364,13 @@ static int of_qcom_slim_ngd_register(struct device *parent,
 
 static int qcom_slim_ngd_probe(struct platform_device *pdev)
 {
-	struct qcom_slim_ngd_ctrl *ctrl = platform_get_drvdata(pdev);
 	struct device *dev = &pdev->dev;
+	struct qcom_slim_ngd_ctrl *ctrl = dev_get_drvdata(dev->parent);
 	int ret;
 
 	ctrl->ctrl.dev = dev;
 
+	platform_set_drvdata(pdev, ctrl);
 	pm_runtime_use_autosuspend(dev);
 	pm_runtime_set_autosuspend_delay(dev, QCOM_SLIM_NGD_AUTOSUSPEND);
 	pm_runtime_set_suspended(dev);
-- 
2.25.1

[PATCH AUTOSEL 4.19 097/172] drm/msm/mdp5: Fix mdp5_init error path for failed mdp5_kms allocation

[Sasha Levin]

From: Roy Spliet <nouveau@spliet.org>

[ Upstream commit e4337877c5d578722c0716f131fb774522013cf5 ]

When allocation for mdp5_kms fails, calling mdp5_destroy() leads to undefined
behaviour, likely a nullptr exception or use-after-free troubles.

Signed-off-by: Roy Spliet <nouveau@spliet.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c b/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c
index bddd625ab91b..25691b7cece1 100644
--- a/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c
+++ b/drivers/gpu/drm/msm/disp/mdp5/mdp5_kms.c
@@ -1021,7 +1021,8 @@ static int mdp5_init(struct platform_device *pdev, struct drm_device *dev)
 
 	return 0;
 fail:
-	mdp5_destroy(pdev);
+	if (mdp5_kms)
+		mdp5_destroy(pdev);
 	return ret;
 }
 
-- 
2.25.1

[PATCH AUTOSEL 4.19 123/172] scsi: ufs-qcom: Fix scheduling while atomic issue

[Sasha Levin]

From: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>

[ Upstream commit 3be60b564de49875e47974c37fabced893cd0931 ]

ufs_qcom_dump_dbg_regs() uses usleep_range, a sleeping function, but can be
called from atomic context in the following flow:

ufshcd_intr -> ufshcd_sl_intr -> ufshcd_check_errors ->
ufshcd_print_host_regs -> ufshcd_vops_dbg_register_dump ->
ufs_qcom_dump_dbg_regs

This causes a boot crash on the Lenovo Miix 630 when the interrupt is
handled on the idle thread.

Fix the issue by switching to udelay().

Link: https://lore.kernel.org/r/20200525204125.46171-1-jeffrey.l.hugo@gmail.com
Fixes: 9c46b8676271 ("scsi: ufs-qcom: dump additional testbus registers")
Reviewed-by: Bean Huo <beanhuo@micron.com>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Signed-off-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/scsi/ufs/ufs-qcom.c | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)

diff --git a/drivers/scsi/ufs/ufs-qcom.c b/drivers/scsi/ufs/ufs-qcom.c
index 75ee5906b966..21e3ff590ec9 100644
--- a/drivers/scsi/ufs/ufs-qcom.c
+++ b/drivers/scsi/ufs/ufs-qcom.c
@@ -1635,11 +1635,11 @@ static void ufs_qcom_dump_dbg_regs(struct ufs_hba *hba)
 
 	/* sleep a bit intermittently as we are dumping too much data */
 	ufs_qcom_print_hw_debug_reg_all(hba, NULL, ufs_qcom_dump_regs_wrapper);
-	usleep_range(1000, 1100);
+	udelay(1000);
 	ufs_qcom_testbus_read(hba);
-	usleep_range(1000, 1100);
+	udelay(1000);
 	ufs_qcom_print_unipro_testbus(hba);
-	usleep_range(1000, 1100);
+	udelay(1000);
 }
 
 /**
-- 
2.25.1