[PATCH v2 00/12] Enable I2C on SA8255p Qualcomm platforms

[PATCH v2 00/12] Enable I2C on SA8255p Qualcomm platforms

[Praveen Talari]

The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.

The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power states(on/off).

The SCMI performance protocol manages I2C frequency, with each
frequency rate represented by a performance level. The driver uses
geni_se_set_perf_opp() API to request the desired frequency rate..

As part of geni_se_set_perf_opp(), the OPP for the requested frequency
is obtained using dev_pm_opp_find_freq_floor() and the performance
level is set using dev_pm_opp_set_opp().

Praveen Talari (12):
  soc: qcom: geni-se: Refactor geni_icc_get() and make qup-memory ICC
    path optional
  soc: qcom: geni-se: Add geni_icc_set_bw_ab() function
  soc: qcom: geni-se: Introduce helper API for resource initialization
  soc: qcom: geni-se: Add resources activation/deactivation helpers
  soc: qcom: geni-se: Introduce helper API for attaching power domains
  soc: qcom: geni-se: Introduce helper APIs for performance control
  dt-bindings: i2c: Describe SA8255p
  i2c: qcom-geni: Isolate serial engine setup
  i2c: qcom-geni: Move resource initialization to separate function
  i2c: qcom-geni: Use resources helper APIs in runtime PM functions
  i2c: qcom-geni: Store of_device_id data in driver private struct
  i2c: qcom-geni: Enable I2C on SA8255p Qualcomm platforms

 .../bindings/i2c/qcom,sa8255p-geni-i2c.yaml   |  64 ++++
 drivers/i2c/busses/i2c-qcom-geni.c            | 300 +++++++++---------
 drivers/soc/qcom/qcom-geni-se.c               | 261 ++++++++++++++-
 include/linux/soc/qcom/geni-se.h              |  19 ++
 4 files changed, 473 insertions(+), 171 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/i2c/qcom,sa8255p-geni-i2c.yaml


base-commit: cc3aa43b44bdb43dfbac0fcb51c56594a11338a8
-- 
2.34.1

[PATCH v2 01/12] soc: qcom: geni-se: Refactor geni_icc_get() and make qup-memory ICC path optional

[Praveen Talari]

The "qup-memory" interconnect path is optional and may not be defined
in all device trees. Unroll the loop-based ICC path initialization to
allow specific error handling for each path type.

The "qup-core" and "qup-config" paths remain mandatory and will fail
probe if missing, while "qup-memory" is now handled as optional and
skipped when not present in the device tree.

Co-developed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1->v2:
Bjorn:
- Updated commit text.
- Used local variable for more readable.
---
 drivers/soc/qcom/qcom-geni-se.c | 36 +++++++++++++++++----------------
 1 file changed, 19 insertions(+), 17 deletions(-)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index cd1779b6a91a..b6167b968ef6 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -899,30 +899,32 @@ EXPORT_SYMBOL_GPL(geni_se_rx_dma_unprep);
 
 int geni_icc_get(struct geni_se *se, const char *icc_ddr)
 {
-	int i, err;
-	const char *icc_names[] = {"qup-core", "qup-config", icc_ddr};
+	struct geni_icc_path *icc_paths = se->icc_paths;
 
 	if (has_acpi_companion(se->dev))
 		return 0;
 
-	for (i = 0; i < ARRAY_SIZE(se->icc_paths); i++) {
-		if (!icc_names[i])
-			continue;
-
-		se->icc_paths[i].path = devm_of_icc_get(se->dev, icc_names[i]);
-		if (IS_ERR(se->icc_paths[i].path))
-			goto err;
+	icc_paths[GENI_TO_CORE].path = devm_of_icc_get(se->dev, "qup-core");
+	if (IS_ERR(icc_paths[GENI_TO_CORE].path))
+		return dev_err_probe(se->dev, PTR_ERR(icc_paths[GENI_TO_CORE].path),
+				     "Failed to get 'qup-core' ICC path\n");
+
+	icc_paths[CPU_TO_GENI].path = devm_of_icc_get(se->dev, "qup-config");
+	if (IS_ERR(icc_paths[CPU_TO_GENI].path))
+		return dev_err_probe(se->dev, PTR_ERR(icc_paths[CPU_TO_GENI].path),
+				     "Failed to get 'qup-config' ICC path\n");
+
+	/* The DDR path is optional, depending on protocol and hw capabilities */
+	icc_paths[GENI_TO_DDR].path = devm_of_icc_get(se->dev, "qup-memory");
+	if (IS_ERR(icc_paths[GENI_TO_DDR].path)) {
+		if (PTR_ERR(icc_paths[GENI_TO_DDR].path) == -ENODATA)
+			icc_paths[GENI_TO_DDR].path = NULL;
+		else
+			return dev_err_probe(se->dev, PTR_ERR(icc_paths[GENI_TO_DDR].path),
+					     "Failed to get 'qup-memory' ICC path\n");
 	}
 
 	return 0;
-
-err:
-	err = PTR_ERR(se->icc_paths[i].path);
-	if (err != -EPROBE_DEFER)
-		dev_err_ratelimited(se->dev, "Failed to get ICC path '%s': %d\n",
-					icc_names[i], err);
-	return err;
-
 }
 EXPORT_SYMBOL_GPL(geni_icc_get);
 
-- 
2.34.1

[PATCH v2 02/12] soc: qcom: geni-se: Add geni_icc_set_bw_ab() function

[Praveen Talari]

Add a new function geni_icc_set_bw_ab() that allows callers to set
average bandwidth values for all ICC (Interconnect) paths in a single
call. This function takes separate parameters for core, config, and DDR
average bandwidth values and applies them to the respective ICC paths.

This provides a more convenient API for drivers that need to configure
specific average bandwidth values.

Co-developed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
 drivers/soc/qcom/qcom-geni-se.c  | 22 ++++++++++++++++++++++
 include/linux/soc/qcom/geni-se.h |  1 +
 2 files changed, 23 insertions(+)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index b6167b968ef6..b0542f836453 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -946,6 +946,28 @@ int geni_icc_set_bw(struct geni_se *se)
 }
 EXPORT_SYMBOL_GPL(geni_icc_set_bw);
 
+/**
+ * geni_icc_set_bw_ab() - Set average bandwidth for all ICC paths and apply
+ * @se:		Pointer to the concerned serial engine.
+ * @core_ab:	Average bandwidth in kBps for GENI_TO_CORE path.
+ * @cfg_ab:	Average bandwidth in kBps for CPU_TO_GENI path.
+ * @ddr_ab:	Average bandwidth in kBps for GENI_TO_DDR path.
+ *
+ * Sets bandwidth values for all ICC paths and applies them. DDR path is
+ * optional and only set if it exists.
+ *
+ * Return: 0 on success, negative error code on failure.
+ */
+int geni_icc_set_bw_ab(struct geni_se *se, u32 core_ab, u32 cfg_ab, u32 ddr_ab)
+{
+	se->icc_paths[GENI_TO_CORE].avg_bw = core_ab;
+	se->icc_paths[CPU_TO_GENI].avg_bw = cfg_ab;
+	se->icc_paths[GENI_TO_DDR].avg_bw = ddr_ab;
+
+	return geni_icc_set_bw(se);
+}
+EXPORT_SYMBOL_GPL(geni_icc_set_bw_ab);
+
 void geni_icc_set_tag(struct geni_se *se, u32 tag)
 {
 	int i;
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index 0a984e2579fe..980aabea2157 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -528,6 +528,7 @@ void geni_se_rx_dma_unprep(struct geni_se *se, dma_addr_t iova, size_t len);
 int geni_icc_get(struct geni_se *se, const char *icc_ddr);
 
 int geni_icc_set_bw(struct geni_se *se);
+int geni_icc_set_bw_ab(struct geni_se *se, u32 core_ab, u32 cfg_ab, u32 ddr_ab);
 void geni_icc_set_tag(struct geni_se *se, u32 tag);
 
 int geni_icc_enable(struct geni_se *se);
-- 
2.34.1

[PATCH v2 03/12] soc: qcom: geni-se: Introduce helper API for resource initialization

[Praveen Talari]

The GENI Serial Engine drivers (I2C, SPI, and SERIAL) currently duplicate
code for initializing shared resources such as clocks and interconnect
paths.

Introduce a new helper API, geni_se_resources_init(), to centralize this
initialization logic, improving modularity and simplifying the probe
function.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1 -> v2:
From kernel test robot
- Updated proper return value for devm_pm_opp_set_clkname()
---
 drivers/soc/qcom/qcom-geni-se.c  | 47 ++++++++++++++++++++++++++++++++
 include/linux/soc/qcom/geni-se.h |  6 ++++
 2 files changed, 53 insertions(+)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index b0542f836453..75e722cd1a94 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -19,6 +19,7 @@
 #include <linux/of_platform.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
+#include <linux/pm_opp.h>
 #include <linux/soc/qcom/geni-se.h>
 
 /**
@@ -1012,6 +1013,52 @@ int geni_icc_disable(struct geni_se *se)
 }
 EXPORT_SYMBOL_GPL(geni_icc_disable);
 
+/**
+ * geni_se_resources_init() - Initialize resources for a GENI SE device.
+ * @se: Pointer to the geni_se structure representing the GENI SE device.
+ *
+ * This function initializes various resources required by the GENI Serial Engine
+ * (SE) device, including clock resources (core and SE clocks), interconnect
+ * paths for communication.
+ * It retrieves optional and mandatory clock resources, adds an OF-based
+ * operating performance point (OPP) table, and sets up interconnect paths
+ * with default bandwidths. The function also sets a flag (`has_opp`) to
+ * indicate whether OPP support is available for the device.
+ *
+ * Return: 0 on success, or a negative errno on failure.
+ */
+int geni_se_resources_init(struct geni_se *se)
+{
+	int ret;
+
+	se->core_clk = devm_clk_get_optional(se->dev, "core");
+	if (IS_ERR(se->core_clk))
+		return dev_err_probe(se->dev, PTR_ERR(se->core_clk),
+				     "Failed to get optional core clk\n");
+
+	se->clk = devm_clk_get(se->dev, "se");
+	if (IS_ERR(se->clk) && !has_acpi_companion(se->dev))
+		return dev_err_probe(se->dev, PTR_ERR(se->clk),
+				     "Failed to get SE clk\n");
+
+	ret = devm_pm_opp_set_clkname(se->dev, "se");
+	if (ret)
+		return ret;
+
+	ret = devm_pm_opp_of_add_table(se->dev);
+	if (ret && ret != -ENODEV)
+		return dev_err_probe(se->dev, ret, "Failed to add OPP table\n");
+
+	se->has_opp = (ret == 0);
+
+	ret = geni_icc_get(se, "qup-memory");
+	if (ret)
+		return ret;
+
+	return geni_icc_set_bw_ab(se, GENI_DEFAULT_BW, GENI_DEFAULT_BW, GENI_DEFAULT_BW);
+}
+EXPORT_SYMBOL_GPL(geni_se_resources_init);
+
 /**
  * geni_find_protocol_fw() - Locate and validate SE firmware for a protocol.
  * @dev: Pointer to the device structure.
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index 980aabea2157..c182dd0f0bde 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -60,18 +60,22 @@ struct geni_icc_path {
  * @dev:		Pointer to the Serial Engine device
  * @wrapper:		Pointer to the parent QUP Wrapper core
  * @clk:		Handle to the core serial engine clock
+ * @core_clk:		Auxiliary clock, which may be required by a protocol
  * @num_clk_levels:	Number of valid clock levels in clk_perf_tbl
  * @clk_perf_tbl:	Table of clock frequency input to serial engine clock
  * @icc_paths:		Array of ICC paths for SE
+ * @has_opp:		Indicates if OPP is supported
  */
 struct geni_se {
 	void __iomem *base;
 	struct device *dev;
 	struct geni_wrapper *wrapper;
 	struct clk *clk;
+	struct clk *core_clk;
 	unsigned int num_clk_levels;
 	unsigned long *clk_perf_tbl;
 	struct geni_icc_path icc_paths[3];
+	bool has_opp;
 };
 
 /* Common SE registers */
@@ -535,6 +539,8 @@ int geni_icc_enable(struct geni_se *se);
 
 int geni_icc_disable(struct geni_se *se);
 
+int geni_se_resources_init(struct geni_se *se);
+
 int geni_load_se_firmware(struct geni_se *se, enum geni_se_protocol_type protocol);
 #endif
 #endif
-- 
2.34.1

[PATCH v2 04/12] soc: qcom: geni-se: Add resources activation/deactivation helpers

[Praveen Talari]

The GENI SE protocol drivers (I2C, SPI, UART) implement similar resource
activation/deactivation sequences independently, leading to code
duplication.

Introduce geni_se_resources_activate()/geni_se_resources_deactivate() to
power on/off resources.The activate function enables ICC, clocks, and TLMM
whereas the deactivate function disables resources in reverse order
including OPP rate reset, clocks, ICC and TLMM.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1 -> v2
Bjorn
- Updated commit message based code changes.
- Removed geni_se_resource_state() API.
- Utilized code snippet from geni_se_resources_off()
---
 drivers/soc/qcom/qcom-geni-se.c  | 77 ++++++++++++++++++++++++++++++++
 include/linux/soc/qcom/geni-se.h |  4 ++
 2 files changed, 81 insertions(+)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index 75e722cd1a94..fbffbc9ea7a6 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -1013,6 +1013,83 @@ int geni_icc_disable(struct geni_se *se)
 }
 EXPORT_SYMBOL_GPL(geni_icc_disable);
 
+/**
+ * geni_se_resources_deactivate() - Deactivate GENI SE device resources
+ * @se: Pointer to the geni_se structure
+ *
+ * Deactivates device resources for power saving: OPP rate to 0, pin control
+ * to sleep state, turns off clocks, and disables interconnect. Skips ACPI devices.
+ *
+ * Return: 0 on success, negative error code on failure
+ */
+int geni_se_resources_deactivate(struct geni_se *se)
+{
+	int ret;
+
+	if (has_acpi_companion(se->dev))
+		return 0;
+
+	if (se->has_opp)
+		dev_pm_opp_set_rate(se->dev, 0);
+
+	ret = pinctrl_pm_select_sleep_state(se->dev);
+	if (ret)
+		return ret;
+
+	geni_se_clks_off(se);
+
+	if (se->core_clk)
+		clk_disable_unprepare(se->core_clk);
+
+	return geni_icc_disable(se);
+}
+
+/**
+ * geni_se_resources_activate() - Activate GENI SE device resources
+ * @se: Pointer to the geni_se structure
+ *
+ * Activates device resources for operation: enables interconnect, prepares clocks,
+ * and sets pin control to default state. Includes error cleanup. Skips ACPI devices.
+ *
+ * Return: 0 on success, negative error code on failure
+ */
+int geni_se_resources_activate(struct geni_se *se)
+{
+	int ret;
+
+	if (has_acpi_companion(se->dev))
+		return 0;
+
+	ret = geni_icc_enable(se);
+	if (ret)
+		return ret;
+
+	if (se->core_clk) {
+		ret = clk_prepare_enable(se->core_clk);
+		if (ret)
+			goto out_icc_disable;
+	}
+
+	ret = geni_se_clks_on(se);
+	if (ret)
+		goto out_clk_disable;
+
+	ret = pinctrl_pm_select_default_state(se->dev);
+	if (ret) {
+		geni_se_clks_off(se);
+		goto out_clk_disable;
+	}
+
+	return ret;
+
+out_clk_disable:
+	if (se->core_clk)
+		clk_disable_unprepare(se->core_clk);
+out_icc_disable:
+	geni_icc_disable(se);
+	return ret;
+}
+
 /**
  * geni_se_resources_init() - Initialize resources for a GENI SE device.
  * @se: Pointer to the geni_se structure representing the GENI SE device.
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index c182dd0f0bde..36a68149345c 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -541,6 +541,10 @@ int geni_icc_disable(struct geni_se *se);
 
 int geni_se_resources_init(struct geni_se *se);
 
+int geni_se_resources_activate(struct geni_se *se);
+
+int geni_se_resources_deactivate(struct geni_se *se);
+
 int geni_load_se_firmware(struct geni_se *se, enum geni_se_protocol_type protocol);
 #endif
 #endif
-- 
2.34.1

[PATCH v2 05/12] soc: qcom: geni-se: Introduce helper API for attaching power domains

[Praveen Talari]

The GENI Serial Engine drivers (I2C, SPI, and SERIAL) currently handle
the attachment of power domains. This often leads to duplicated code
logic across different driver probe functions.

Introduce a new helper API, geni_se_domain_attach(), to centralize
the logic for attaching "power" and "perf" domains to the GENI SE
device.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
 drivers/soc/qcom/qcom-geni-se.c  | 29 +++++++++++++++++++++++++++++
 include/linux/soc/qcom/geni-se.h |  4 ++++
 2 files changed, 33 insertions(+)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index fbffbc9ea7a6..decf7cf5172e 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -19,6 +19,7 @@
 #include <linux/of_platform.h>
 #include <linux/pinctrl/consumer.h>
 #include <linux/platform_device.h>
+#include <linux/pm_domain.h>
 #include <linux/pm_opp.h>
 #include <linux/soc/qcom/geni-se.h>
 
@@ -1090,6 +1091,34 @@ int geni_se_resources_activate(struct geni_se *se)
 	return ret;
 }
 
+/**
+ * geni_se_domain_attach() - Attach power domains to a GENI SE device.
+ * @se: Pointer to the geni_se structure representing the GENI SE device.
+ *
+ * This function attaches the necessary power domains ("power" and "perf")
+ * to the GENI Serial Engine device. It initializes `se->pd_list` with the
+ * attached domains.
+ *
+ * Return: 0 on success, or a negative error code on failure.
+ */
+int geni_se_domain_attach(struct geni_se *se)
+{
+	struct dev_pm_domain_attach_data pd_data = {
+		.pd_flags = PD_FLAG_DEV_LINK_ON,
+		.pd_names = (const char*[]) { "power", "perf" },
+		.num_pd_names = 2,
+	};
+	int ret;
+
+	ret = dev_pm_domain_attach_list(se->dev,
+					&pd_data, &se->pd_list);
+	if (ret <= 0)
+		return -EINVAL;
+
+	return 0;
+}
+EXPORT_SYMBOL_GPL(geni_se_domain_attach);
+
 /**
  * geni_se_resources_init() - Initialize resources for a GENI SE device.
  * @se: Pointer to the geni_se structure representing the GENI SE device.
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index 36a68149345c..5f75159c5531 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -64,6 +64,7 @@ struct geni_icc_path {
  * @num_clk_levels:	Number of valid clock levels in clk_perf_tbl
  * @clk_perf_tbl:	Table of clock frequency input to serial engine clock
  * @icc_paths:		Array of ICC paths for SE
+ * @pd_list:		Power domain list for managing power domains
  * @has_opp:		Indicates if OPP is supported
  */
 struct geni_se {
@@ -75,6 +76,7 @@ struct geni_se {
 	unsigned int num_clk_levels;
 	unsigned long *clk_perf_tbl;
 	struct geni_icc_path icc_paths[3];
+	struct dev_pm_domain_list *pd_list;
 	bool has_opp;
 };
 
@@ -546,5 +548,7 @@ int geni_se_resources_activate(struct geni_se *se);
 int geni_se_resources_deactivate(struct geni_se *se);
 
 int geni_load_se_firmware(struct geni_se *se, enum geni_se_protocol_type protocol);
+
+int geni_se_domain_attach(struct geni_se *se);
 #endif
 #endif
-- 
2.34.1

[PATCH v2 06/12] soc: qcom: geni-se: Introduce helper APIs for performance control

[Praveen Talari]

The GENI Serial Engine (SE) drivers (I2C, SPI, and SERIAL) currently
manage performance levels and operating points directly. This resulting
in code duplication across drivers. such as configuring a specific level
or find and apply an OPP based on a clock frequency.

Introduce two new helper APIs, geni_se_set_perf_level() and
geni_se_set_perf_opp(), addresses this issue by providing a streamlined
method for the GENI Serial Engine (SE) drivers to find and set the OPP
based on the desired performance level, thereby eliminating redundancy.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
 drivers/soc/qcom/qcom-geni-se.c  | 50 ++++++++++++++++++++++++++++++++
 include/linux/soc/qcom/geni-se.h |  4 +++
 2 files changed, 54 insertions(+)

diff --git a/drivers/soc/qcom/qcom-geni-se.c b/drivers/soc/qcom/qcom-geni-se.c
index decf7cf5172e..fd63cc6a7faf 100644
--- a/drivers/soc/qcom/qcom-geni-se.c
+++ b/drivers/soc/qcom/qcom-geni-se.c
@@ -282,6 +282,12 @@ struct se_fw_hdr {
 #define geni_setbits32(_addr, _v) writel(readl(_addr) |  (_v), _addr)
 #define geni_clrbits32(_addr, _v) writel(readl(_addr) & ~(_v), _addr)
 
+enum domain_idx {
+	DOMAIN_IDX_POWER,
+	DOMAIN_IDX_PERF,
+	DOMAIN_IDX_MAX
+};
+
 /**
  * geni_se_get_qup_hw_version() - Read the QUP wrapper Hardware version
  * @se:	Pointer to the corresponding serial engine.
@@ -1091,6 +1097,50 @@ int geni_se_resources_activate(struct geni_se *se)
 	return ret;
 }
 
+/**
+ * geni_se_set_perf_level() - Set performance level for GENI SE.
+ * @se: Pointer to the struct geni_se instance.
+ * @level: The desired performance level.
+ *
+ * Sets the performance level by directly calling dev_pm_opp_set_level
+ * on the performance device associated with the SE.
+ *
+ * Return: 0 on success, or a negative error code on failure.
+ */
+int geni_se_set_perf_level(struct geni_se *se, unsigned long level)
+{
+	return dev_pm_opp_set_level(se->pd_list->pd_devs[DOMAIN_IDX_PERF], level);
+}
+EXPORT_SYMBOL_GPL(geni_se_set_perf_level);
+
+/**
+ * geni_se_set_perf_opp() - Set performance OPP for GENI SE by frequency.
+ * @se: Pointer to the struct geni_se instance.
+ * @clk_freq: The requested clock frequency.
+ *
+ * Finds the nearest operating performance point (OPP) for the given
+ * clock frequency and applies it to the SE's performance device.
+ *
+ * Return: 0 on success, or a negative error code on failure.
+ */
+int geni_se_set_perf_opp(struct geni_se *se, unsigned long clk_freq)
+{
+	struct device *perf_dev = se->pd_list->pd_devs[DOMAIN_IDX_PERF];
+	struct dev_pm_opp *opp;
+	int ret;
+
+	opp = dev_pm_opp_find_freq_floor(perf_dev, &clk_freq);
+	if (IS_ERR(opp)) {
+		dev_err(se->dev, "failed to find opp for freq %lu\n", clk_freq);
+		return PTR_ERR(opp);
+	}
+
+	ret = dev_pm_opp_set_opp(perf_dev, opp);
+	dev_pm_opp_put(opp);
+	return ret;
+}
+EXPORT_SYMBOL_GPL(geni_se_set_perf_opp);
+
 /**
  * geni_se_domain_attach() - Attach power domains to a GENI SE device.
  * @se: Pointer to the geni_se structure representing the GENI SE device.
diff --git a/include/linux/soc/qcom/geni-se.h b/include/linux/soc/qcom/geni-se.h
index 5f75159c5531..c5e6ab85df09 100644
--- a/include/linux/soc/qcom/geni-se.h
+++ b/include/linux/soc/qcom/geni-se.h
@@ -550,5 +550,9 @@ int geni_se_resources_deactivate(struct geni_se *se);
 int geni_load_se_firmware(struct geni_se *se, enum geni_se_protocol_type protocol);
 
 int geni_se_domain_attach(struct geni_se *se);
+
+int geni_se_set_perf_level(struct geni_se *se, unsigned long level);
+
+int geni_se_set_perf_opp(struct geni_se *se, unsigned long clk_freq);
 #endif
 #endif
-- 
2.34.1

[PATCH v2 07/12] dt-bindings: i2c: Describe SA8255p

[Praveen Talari]

Add DT bindings for the QUP GENI I2C controller on sa8255p platforms.

SA8255p platform abstracts resources such as clocks, interconnect and
GPIO pins configuration in Firmware. SCMI power and perf protocol
are utilized to request resource configurations.

SA8255p platform does not require the Serial Engine (SE) common properties
as the SE firmware is loaded and managed by the TrustZone (TZ) secure
environment.

Co-developed-by: Nikunj Kela <quic_nkela@quicinc.com>
Signed-off-by: Nikunj Kela <quic_nkela@quicinc.com>
Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1->v2:
Krzysztof:
- Added dma properties in example node
- Removed minItems from power-domains property
- Added in commit text about common property
---
 .../bindings/i2c/qcom,sa8255p-geni-i2c.yaml   | 64 +++++++++++++++++++
 1 file changed, 64 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/i2c/qcom,sa8255p-geni-i2c.yaml

diff --git a/Documentation/devicetree/bindings/i2c/qcom,sa8255p-geni-i2c.yaml b/Documentation/devicetree/bindings/i2c/qcom,sa8255p-geni-i2c.yaml
new file mode 100644
index 000000000000..a61e40b5cbc1
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/qcom,sa8255p-geni-i2c.yaml
@@ -0,0 +1,64 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/qcom,sa8255p-geni-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SA8255p QUP GENI I2C Controller
+
+maintainers:
+  - Praveen Talari <praveen.talari@oss.qualcomm.com>
+
+properties:
+  compatible:
+    const: qcom,sa8255p-geni-i2c
+
+  reg:
+    maxItems: 1
+
+  dmas:
+    maxItems: 2
+
+  dma-names:
+    items:
+      - const: tx
+      - const: rx
+
+  interrupts:
+    maxItems: 1
+
+  power-domains:
+    maxItems: 2
+
+  power-domain-names:
+    items:
+      - const: power
+      - const: perf
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - power-domains
+
+allOf:
+  - $ref: /schemas/i2c/i2c-controller.yaml#
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+    #include <dt-bindings/dma/qcom-gpi.h>
+
+    i2c@a90000 {
+        compatible = "qcom,sa8255p-geni-i2c";
+        reg = <0xa90000 0x4000>;
+        interrupts = <GIC_SPI 357 IRQ_TYPE_LEVEL_HIGH>;
+        dmas = <&gpi_dma0 0 0 QCOM_GPI_I2C>,
+               <&gpi_dma0 1 0 QCOM_GPI_I2C>;
+        dma-names = "tx", "rx";
+        power-domains = <&scmi0_pd 0>, <&scmi0_dvfs 0>;
+        power-domain-names = "power", "perf";
+    };
+...
-- 
2.34.1

[PATCH v2 08/12] i2c: qcom-geni: Isolate serial engine setup

[Praveen Talari]

Moving the serial engine setup to geni_i2c_init() API for a cleaner
probe function and utilizes the PM runtime API to control resources
instead of direct clock-related APIs for better resource management.

Enables reusability of the serial engine initialization like
hibernation and deep sleep features where hardware context is lost.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1->v2:
Bjorn:
- Updated commit text.
---
 drivers/i2c/busses/i2c-qcom-geni.c | 154 ++++++++++++++---------------
 1 file changed, 73 insertions(+), 81 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index 3a04016db2c3..58c32ffbd150 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -976,10 +976,75 @@ static int setup_gpi_dma(struct geni_i2c_dev *gi2c)
 	return ret;
 }
 
+static int geni_i2c_init(struct geni_i2c_dev *gi2c)
+{
+	const struct geni_i2c_desc *desc = NULL;
+	u32 proto, tx_depth;
+	bool fifo_disable;
+	int ret;
+
+	ret = pm_runtime_resume_and_get(gi2c->se.dev);
+	if (ret < 0) {
+		dev_err(gi2c->se.dev, "error turning on device :%d\n", ret);
+		return ret;
+	}
+
+	proto = geni_se_read_proto(&gi2c->se);
+	if (proto == GENI_SE_INVALID_PROTO) {
+		ret = geni_load_se_firmware(&gi2c->se, GENI_SE_I2C);
+		if (ret) {
+			dev_err_probe(gi2c->se.dev, ret, "i2c firmware load failed ret: %d\n", ret);
+			goto err;
+		}
+	} else if (proto != GENI_SE_I2C) {
+		ret = dev_err_probe(gi2c->se.dev, -ENXIO, "Invalid proto %d\n", proto);
+		goto err;
+	}
+
+	desc = device_get_match_data(gi2c->se.dev);
+	if (desc && desc->no_dma_support)
+		fifo_disable = false;
+	else
+		fifo_disable = readl_relaxed(gi2c->se.base + GENI_IF_DISABLE_RO) & FIFO_IF_DISABLE;
+
+	if (fifo_disable) {
+		/* FIFO is disabled, so we can only use GPI DMA */
+		gi2c->gpi_mode = true;
+		ret = setup_gpi_dma(gi2c);
+		if (ret)
+			goto err;
+
+		dev_dbg(gi2c->se.dev, "Using GPI DMA mode for I2C\n");
+	} else {
+		gi2c->gpi_mode = false;
+		tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
+
+		/* I2C Master Hub Serial Elements doesn't have the HW_PARAM_0 register */
+		if (!tx_depth && desc)
+			tx_depth = desc->tx_fifo_depth;
+
+		if (!tx_depth) {
+			ret = dev_err_probe(gi2c->se.dev, -EINVAL,
+					    "Invalid TX FIFO depth\n");
+			goto err;
+		}
+
+		gi2c->tx_wm = tx_depth - 1;
+		geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
+		geni_se_config_packing(&gi2c->se, BITS_PER_BYTE,
+				       PACKING_BYTES_PW, true, true, true);
+
+		dev_dbg(gi2c->se.dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
+	}
+
+err:
+	pm_runtime_put(gi2c->se.dev);
+	return ret;
+}
+
 static int geni_i2c_probe(struct platform_device *pdev)
 {
 	struct geni_i2c_dev *gi2c;
-	u32 proto, tx_depth, fifo_disable;
 	int ret;
 	struct device *dev = &pdev->dev;
 	const struct geni_i2c_desc *desc = NULL;
@@ -1059,100 +1124,27 @@ static int geni_i2c_probe(struct platform_device *pdev)
 	if (ret)
 		return ret;
 
-	ret = clk_prepare_enable(gi2c->core_clk);
-	if (ret)
-		return ret;
-
-	ret = geni_se_resources_on(&gi2c->se);
-	if (ret) {
-		dev_err_probe(dev, ret, "Error turning on resources\n");
-		goto err_clk;
-	}
-	proto = geni_se_read_proto(&gi2c->se);
-	if (proto == GENI_SE_INVALID_PROTO) {
-		ret = geni_load_se_firmware(&gi2c->se, GENI_SE_I2C);
-		if (ret) {
-			dev_err_probe(dev, ret, "i2c firmware load failed ret: %d\n", ret);
-			goto err_resources;
-		}
-	} else if (proto != GENI_SE_I2C) {
-		ret = dev_err_probe(dev, -ENXIO, "Invalid proto %d\n", proto);
-		goto err_resources;
-	}
-
-	if (desc && desc->no_dma_support)
-		fifo_disable = false;
-	else
-		fifo_disable = readl_relaxed(gi2c->se.base + GENI_IF_DISABLE_RO) & FIFO_IF_DISABLE;
-
-	if (fifo_disable) {
-		/* FIFO is disabled, so we can only use GPI DMA */
-		gi2c->gpi_mode = true;
-		ret = setup_gpi_dma(gi2c);
-		if (ret)
-			goto err_resources;
-
-		dev_dbg(dev, "Using GPI DMA mode for I2C\n");
-	} else {
-		gi2c->gpi_mode = false;
-		tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
-
-		/* I2C Master Hub Serial Elements doesn't have the HW_PARAM_0 register */
-		if (!tx_depth && desc)
-			tx_depth = desc->tx_fifo_depth;
-
-		if (!tx_depth) {
-			ret = dev_err_probe(dev, -EINVAL,
-					    "Invalid TX FIFO depth\n");
-			goto err_resources;
-		}
-
-		gi2c->tx_wm = tx_depth - 1;
-		geni_se_init(&gi2c->se, gi2c->tx_wm, tx_depth);
-		geni_se_config_packing(&gi2c->se, BITS_PER_BYTE,
-				       PACKING_BYTES_PW, true, true, true);
-
-		dev_dbg(dev, "i2c fifo/se-dma mode. fifo depth:%d\n", tx_depth);
-	}
-
-	clk_disable_unprepare(gi2c->core_clk);
-	ret = geni_se_resources_off(&gi2c->se);
-	if (ret) {
-		dev_err_probe(dev, ret, "Error turning off resources\n");
-		goto err_dma;
-	}
-
-	ret = geni_icc_disable(&gi2c->se);
-	if (ret)
-		goto err_dma;
-
 	gi2c->suspended = 1;
 	pm_runtime_set_suspended(gi2c->se.dev);
 	pm_runtime_set_autosuspend_delay(gi2c->se.dev, I2C_AUTO_SUSPEND_DELAY);
 	pm_runtime_use_autosuspend(gi2c->se.dev);
 	pm_runtime_enable(gi2c->se.dev);
 
+	ret =  geni_i2c_init(gi2c);
+	if (ret < 0) {
+		pm_runtime_disable(gi2c->se.dev);
+		return ret;
+	}
+
 	ret = i2c_add_adapter(&gi2c->adap);
 	if (ret) {
 		dev_err_probe(dev, ret, "Error adding i2c adapter\n");
 		pm_runtime_disable(gi2c->se.dev);
-		goto err_dma;
+		return ret;
 	}
 
 	dev_dbg(dev, "Geni-I2C adaptor successfully added\n");
 
-	return ret;
-
-err_resources:
-	geni_se_resources_off(&gi2c->se);
-err_clk:
-	clk_disable_unprepare(gi2c->core_clk);
-
-	return ret;
-
-err_dma:
-	release_gpi_dma(gi2c);
-
 	return ret;
 }
 
-- 
2.34.1

[PATCH v2 09/12] i2c: qcom-geni: Move resource initialization to separate function

[Praveen Talari]

Refactor the resource initialization in geni_i2c_probe() by introducing
a new geni_i2c_resources_init() function and utilizing the common
geni_se_resources_init() framework and clock frequency mapping, making the
probe function cleaner.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1->v2:
- Updated commit text.
---
 drivers/i2c/busses/i2c-qcom-geni.c | 53 ++++++++++++------------------
 1 file changed, 21 insertions(+), 32 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index 58c32ffbd150..a4b13022e508 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -1042,6 +1042,23 @@ static int geni_i2c_init(struct geni_i2c_dev *gi2c)
 	return ret;
 }
 
+static int geni_i2c_resources_init(struct geni_i2c_dev *gi2c)
+{
+	int ret;
+
+	ret = geni_se_resources_init(&gi2c->se);
+	if (ret)
+		return ret;
+
+	ret = geni_i2c_clk_map_idx(gi2c);
+	if (ret)
+		return dev_err_probe(gi2c->se.dev, ret, "Invalid clk frequency %d Hz\n",
+				     gi2c->clk_freq_out);
+
+	return geni_icc_set_bw_ab(&gi2c->se, GENI_DEFAULT_BW, GENI_DEFAULT_BW,
+				  Bps_to_icc(gi2c->clk_freq_out));
+}
+
 static int geni_i2c_probe(struct platform_device *pdev)
 {
 	struct geni_i2c_dev *gi2c;
@@ -1061,16 +1078,6 @@ static int geni_i2c_probe(struct platform_device *pdev)
 
 	desc = device_get_match_data(&pdev->dev);
 
-	if (desc && desc->has_core_clk) {
-		gi2c->core_clk = devm_clk_get(dev, "core");
-		if (IS_ERR(gi2c->core_clk))
-			return PTR_ERR(gi2c->core_clk);
-	}
-
-	gi2c->se.clk = devm_clk_get(dev, "se");
-	if (IS_ERR(gi2c->se.clk) && !has_acpi_companion(dev))
-		return PTR_ERR(gi2c->se.clk);
-
 	ret = device_property_read_u32(dev, "clock-frequency",
 				       &gi2c->clk_freq_out);
 	if (ret) {
@@ -1085,16 +1092,15 @@ static int geni_i2c_probe(struct platform_device *pdev)
 	if (gi2c->irq < 0)
 		return gi2c->irq;
 
-	ret = geni_i2c_clk_map_idx(gi2c);
-	if (ret)
-		return dev_err_probe(dev, ret, "Invalid clk frequency %d Hz\n",
-				     gi2c->clk_freq_out);
-
 	gi2c->adap.algo = &geni_i2c_algo;
 	init_completion(&gi2c->done);
 	spin_lock_init(&gi2c->lock);
 	platform_set_drvdata(pdev, gi2c);
 
+	ret = geni_i2c_resources_init(gi2c);
+	if (ret)
+		return ret;
+
 	/* Keep interrupts disabled initially to allow for low-power modes */
 	ret = devm_request_irq(dev, gi2c->irq, geni_i2c_irq, IRQF_NO_AUTOEN,
 			       dev_name(dev), gi2c);
@@ -1107,23 +1113,6 @@ static int geni_i2c_probe(struct platform_device *pdev)
 	gi2c->adap.dev.of_node = dev->of_node;
 	strscpy(gi2c->adap.name, "Geni-I2C", sizeof(gi2c->adap.name));
 
-	ret = geni_icc_get(&gi2c->se, desc ? desc->icc_ddr : "qup-memory");
-	if (ret)
-		return ret;
-	/*
-	 * Set the bus quota for core and cpu to a reasonable value for
-	 * register access.
-	 * Set quota for DDR based on bus speed.
-	 */
-	gi2c->se.icc_paths[GENI_TO_CORE].avg_bw = GENI_DEFAULT_BW;
-	gi2c->se.icc_paths[CPU_TO_GENI].avg_bw = GENI_DEFAULT_BW;
-	if (!desc || desc->icc_ddr)
-		gi2c->se.icc_paths[GENI_TO_DDR].avg_bw = Bps_to_icc(gi2c->clk_freq_out);
-
-	ret = geni_icc_set_bw(&gi2c->se);
-	if (ret)
-		return ret;
-
 	gi2c->suspended = 1;
 	pm_runtime_set_suspended(gi2c->se.dev);
 	pm_runtime_set_autosuspend_delay(gi2c->se.dev, I2C_AUTO_SUSPEND_DELAY);
-- 
2.34.1

[PATCH v2 10/12] i2c: qcom-geni: Use resources helper APIs in runtime PM functions

[Praveen Talari]

To manage GENI serial engine resources during runtime power management,
drivers currently need to call functions for ICC, clock, and
SE resource operations in both suspend and resume paths, resulting in
code duplication across drivers.

The new geni_se_resources_activate() and geni_se_resources_deactivate()
helper APIs addresses this issue by providing a streamlined method to
enable or disable all resources based, thereby eliminating redundancy
across drivers.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
v1->v2:
Bjorn:
- Remove geni_se_resources_state() API.
- Used geni_se_resources_activate() and geni_se_resources_deactivate()
  to enable/disable resources.
---
 drivers/i2c/busses/i2c-qcom-geni.c | 28 +++++-----------------------
 1 file changed, 5 insertions(+), 23 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index a4b13022e508..b0a18e3d57d9 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -1160,18 +1160,15 @@ static int __maybe_unused geni_i2c_runtime_suspend(struct device *dev)
 	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
 
 	disable_irq(gi2c->irq);
-	ret = geni_se_resources_off(&gi2c->se);
+
+	ret = geni_se_resources_deactivate(&gi2c->se);
 	if (ret) {
 		enable_irq(gi2c->irq);
 		return ret;
-
-	} else {
-		gi2c->suspended = 1;
 	}
 
-	clk_disable_unprepare(gi2c->core_clk);
-
-	return geni_icc_disable(&gi2c->se);
+	gi2c->suspended = 1;
+	return ret;
 }
 
 static int __maybe_unused geni_i2c_runtime_resume(struct device *dev)
@@ -1179,28 +1176,13 @@ static int __maybe_unused geni_i2c_runtime_resume(struct device *dev)
 	int ret;
 	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
 
-	ret = geni_icc_enable(&gi2c->se);
+	ret = geni_se_resources_activate(&gi2c->se);
 	if (ret)
 		return ret;
 
-	ret = clk_prepare_enable(gi2c->core_clk);
-	if (ret)
-		goto out_icc_disable;
-
-	ret = geni_se_resources_on(&gi2c->se);
-	if (ret)
-		goto out_clk_disable;
-
 	enable_irq(gi2c->irq);
 	gi2c->suspended = 0;
 
-	return 0;
-
-out_clk_disable:
-	clk_disable_unprepare(gi2c->core_clk);
-out_icc_disable:
-	geni_icc_disable(&gi2c->se);
-
 	return ret;
 }
 
-- 
2.34.1

[PATCH v2 11/12] i2c: qcom-geni: Store of_device_id data in driver private struct

[Praveen Talari]

To avoid repeatedly fetching and checking platform data across various
functions, store the struct of_device_id data directly in the i2c
private structure. This change enhances code maintainability and reduces
redundancy.

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
 drivers/i2c/busses/i2c-qcom-geni.c | 32 ++++++++++++++++--------------
 1 file changed, 17 insertions(+), 15 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index b0a18e3d57d9..1c9356e13b97 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -77,6 +77,13 @@ enum geni_i2c_err_code {
 #define XFER_TIMEOUT		HZ
 #define RST_TIMEOUT		HZ
 
+struct geni_i2c_desc {
+	bool has_core_clk;
+	char *icc_ddr;
+	bool no_dma_support;
+	unsigned int tx_fifo_depth;
+};
+
 #define QCOM_I2C_MIN_NUM_OF_MSGS_MULTI_DESC	2
 
 /**
@@ -121,13 +128,7 @@ struct geni_i2c_dev {
 	bool is_tx_multi_desc_xfer;
 	u32 num_msgs;
 	struct geni_i2c_gpi_multi_desc_xfer i2c_multi_desc_config;
-};
-
-struct geni_i2c_desc {
-	bool has_core_clk;
-	char *icc_ddr;
-	bool no_dma_support;
-	unsigned int tx_fifo_depth;
+	const struct geni_i2c_desc *dev_data;
 };
 
 struct geni_i2c_err_log {
@@ -978,7 +979,6 @@ static int setup_gpi_dma(struct geni_i2c_dev *gi2c)
 
 static int geni_i2c_init(struct geni_i2c_dev *gi2c)
 {
-	const struct geni_i2c_desc *desc = NULL;
 	u32 proto, tx_depth;
 	bool fifo_disable;
 	int ret;
@@ -1001,8 +1001,7 @@ static int geni_i2c_init(struct geni_i2c_dev *gi2c)
 		goto err;
 	}
 
-	desc = device_get_match_data(gi2c->se.dev);
-	if (desc && desc->no_dma_support)
+	if (gi2c->dev_data->no_dma_support)
 		fifo_disable = false;
 	else
 		fifo_disable = readl_relaxed(gi2c->se.base + GENI_IF_DISABLE_RO) & FIFO_IF_DISABLE;
@@ -1020,8 +1019,8 @@ static int geni_i2c_init(struct geni_i2c_dev *gi2c)
 		tx_depth = geni_se_get_tx_fifo_depth(&gi2c->se);
 
 		/* I2C Master Hub Serial Elements doesn't have the HW_PARAM_0 register */
-		if (!tx_depth && desc)
-			tx_depth = desc->tx_fifo_depth;
+		if (!tx_depth && gi2c->dev_data->has_core_clk)
+			tx_depth = gi2c->dev_data->tx_fifo_depth;
 
 		if (!tx_depth) {
 			ret = dev_err_probe(gi2c->se.dev, -EINVAL,
@@ -1064,7 +1063,6 @@ static int geni_i2c_probe(struct platform_device *pdev)
 	struct geni_i2c_dev *gi2c;
 	int ret;
 	struct device *dev = &pdev->dev;
-	const struct geni_i2c_desc *desc = NULL;
 
 	gi2c = devm_kzalloc(dev, sizeof(*gi2c), GFP_KERNEL);
 	if (!gi2c)
@@ -1076,7 +1074,7 @@ static int geni_i2c_probe(struct platform_device *pdev)
 	if (IS_ERR(gi2c->se.base))
 		return PTR_ERR(gi2c->se.base);
 
-	desc = device_get_match_data(&pdev->dev);
+	gi2c->dev_data = device_get_match_data(&pdev->dev);
 
 	ret = device_property_read_u32(dev, "clock-frequency",
 				       &gi2c->clk_freq_out);
@@ -1215,6 +1213,10 @@ static const struct dev_pm_ops geni_i2c_pm_ops = {
 									NULL)
 };
 
+static const struct geni_i2c_desc geni_i2c = {
+	.icc_ddr = "qup-memory",
+};
+
 static const struct geni_i2c_desc i2c_master_hub = {
 	.has_core_clk = true,
 	.icc_ddr = NULL,
@@ -1223,7 +1225,7 @@ static const struct geni_i2c_desc i2c_master_hub = {
 };
 
 static const struct of_device_id geni_i2c_dt_match[] = {
-	{ .compatible = "qcom,geni-i2c" },
+	{ .compatible = "qcom,geni-i2c", .data = &geni_i2c },
 	{ .compatible = "qcom,geni-i2c-master-hub", .data = &i2c_master_hub },
 	{}
 };
-- 
2.34.1

[PATCH v2 12/12] i2c: qcom-geni: Enable I2C on SA8255p Qualcomm platforms

[Praveen Talari]

The Qualcomm automotive SA8255p SoC relies on firmware to configure
platform resources, including clocks, interconnects and TLMM.
The driver requests resources operations over SCMI using power
and performance protocols.

The SCMI power protocol enables or disables resources like clocks,
interconnect paths, and TLMM (GPIOs) using runtime PM framework APIs,
such as resume/suspend, to control power on/off.

The SCMI performance protocol manages I2C frequency, with each
frequency rate represented by a performance level. The driver uses
geni_se_set_perf_opp() API to request the desired frequency rate..

As part of geni_se_set_perf_opp(), the OPP for the requested frequency
is obtained using dev_pm_opp_find_freq_floor() and the performance
level is set using dev_pm_opp_set_opp().

Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>
---
V1->v2:
From kernel test robot:
- Initialized ret to "0" in resume/suspend callbacks.

Bjorn:
- Used seperate APIs for the resouces enable/disable.
---
 drivers/i2c/busses/i2c-qcom-geni.c | 53 ++++++++++++++++++++++--------
 1 file changed, 40 insertions(+), 13 deletions(-)

diff --git a/drivers/i2c/busses/i2c-qcom-geni.c b/drivers/i2c/busses/i2c-qcom-geni.c
index 1c9356e13b97..72457b98f155 100644
--- a/drivers/i2c/busses/i2c-qcom-geni.c
+++ b/drivers/i2c/busses/i2c-qcom-geni.c
@@ -82,6 +82,10 @@ struct geni_i2c_desc {
 	char *icc_ddr;
 	bool no_dma_support;
 	unsigned int tx_fifo_depth;
+	int (*resources_init)(struct geni_se *se);
+	int (*set_rate)(struct geni_se *se, unsigned long freq);
+	int (*power_on)(struct geni_se *se);
+	int (*power_off)(struct geni_se *se);
 };
 
 #define QCOM_I2C_MIN_NUM_OF_MSGS_MULTI_DESC	2
@@ -203,8 +207,9 @@ static int geni_i2c_clk_map_idx(struct geni_i2c_dev *gi2c)
 	return -EINVAL;
 }
 
-static void qcom_geni_i2c_conf(struct geni_i2c_dev *gi2c)
+static int qcom_geni_i2c_conf(struct geni_se *se, unsigned long freq)
 {
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(se->dev);
 	const struct geni_i2c_clk_fld *itr = gi2c->clk_fld;
 	u32 val;
 
@@ -217,6 +222,7 @@ static void qcom_geni_i2c_conf(struct geni_i2c_dev *gi2c)
 	val |= itr->t_low_cnt << LOW_COUNTER_SHFT;
 	val |= itr->t_cycle_cnt;
 	writel_relaxed(val, gi2c->se.base + SE_I2C_SCL_COUNTERS);
+	return 0;
 }
 
 static void geni_i2c_err_misc(struct geni_i2c_dev *gi2c)
@@ -908,7 +914,9 @@ static int geni_i2c_xfer(struct i2c_adapter *adap,
 		return ret;
 	}
 
-	qcom_geni_i2c_conf(gi2c);
+	ret = gi2c->dev_data->set_rate(&gi2c->se, gi2c->clk_freq_out);
+	if (ret)
+		return ret;
 
 	if (gi2c->gpi_mode)
 		ret = geni_i2c_gpi_xfer(gi2c, msgs, num);
@@ -1041,8 +1049,9 @@ static int geni_i2c_init(struct geni_i2c_dev *gi2c)
 	return ret;
 }
 
-static int geni_i2c_resources_init(struct geni_i2c_dev *gi2c)
+static int geni_i2c_resources_init(struct geni_se *se)
 {
+	struct geni_i2c_dev *gi2c = dev_get_drvdata(se->dev);
 	int ret;
 
 	ret = geni_se_resources_init(&gi2c->se);
@@ -1095,7 +1104,7 @@ static int geni_i2c_probe(struct platform_device *pdev)
 	spin_lock_init(&gi2c->lock);
 	platform_set_drvdata(pdev, gi2c);
 
-	ret = geni_i2c_resources_init(gi2c);
+	ret = gi2c->dev_data->resources_init(&gi2c->se);
 	if (ret)
 		return ret;
 
@@ -1154,15 +1163,17 @@ static void geni_i2c_shutdown(struct platform_device *pdev)
 
 static int __maybe_unused geni_i2c_runtime_suspend(struct device *dev)
 {
-	int ret;
+	int ret = 0;
 	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
 
 	disable_irq(gi2c->irq);
 
-	ret = geni_se_resources_deactivate(&gi2c->se);
-	if (ret) {
-		enable_irq(gi2c->irq);
-		return ret;
+	if (gi2c->dev_data->power_off) {
+		ret = gi2c->dev_data->power_off(&gi2c->se);
+		if (ret) {
+			enable_irq(gi2c->irq);
+			return ret;
+		}
 	}
 
 	gi2c->suspended = 1;
@@ -1171,12 +1182,14 @@ static int __maybe_unused geni_i2c_runtime_suspend(struct device *dev)
 
 static int __maybe_unused geni_i2c_runtime_resume(struct device *dev)
 {
-	int ret;
+	int ret = 0;
 	struct geni_i2c_dev *gi2c = dev_get_drvdata(dev);
 
-	ret = geni_se_resources_activate(&gi2c->se);
-	if (ret)
-		return ret;
+	if (gi2c->dev_data->power_on) {
+		ret = gi2c->dev_data->power_on(&gi2c->se);
+		if (ret)
+			return ret;
+	}
 
 	enable_irq(gi2c->irq);
 	gi2c->suspended = 0;
@@ -1215,6 +1228,10 @@ static const struct dev_pm_ops geni_i2c_pm_ops = {
 
 static const struct geni_i2c_desc geni_i2c = {
 	.icc_ddr = "qup-memory",
+	.resources_init = geni_i2c_resources_init,
+	.set_rate = qcom_geni_i2c_conf,
+	.power_on = geni_se_resources_activate,
+	.power_off = geni_se_resources_deactivate,
 };
 
 static const struct geni_i2c_desc i2c_master_hub = {
@@ -1222,11 +1239,21 @@ static const struct geni_i2c_desc i2c_master_hub = {
 	.icc_ddr = NULL,
 	.no_dma_support = true,
 	.tx_fifo_depth = 16,
+	.resources_init = geni_i2c_resources_init,
+	.set_rate = qcom_geni_i2c_conf,
+	.power_on = geni_se_resources_activate,
+	.power_off = geni_se_resources_deactivate,
+};
+
+static const struct geni_i2c_desc sa8255p_geni_i2c = {
+	.resources_init = geni_se_domain_attach,
+	.set_rate = geni_se_set_perf_opp,
 };
 
 static const struct of_device_id geni_i2c_dt_match[] = {
 	{ .compatible = "qcom,geni-i2c", .data = &geni_i2c },
 	{ .compatible = "qcom,geni-i2c-master-hub", .data = &i2c_master_hub },
+	{ .compatible = "qcom,sa8255p-geni-i2c", .data = &sa8255p_geni_i2c },
 	{}
 };
 MODULE_DEVICE_TABLE(of, geni_i2c_dt_match);
-- 
2.34.1

Re: [PATCH v2 07/12] dt-bindings: i2c: Describe SA8255p

[Krzysztof Kozlowski]

On Mon, Dec 29, 2025 at 10:24:41AM +0530, Praveen Talari wrote:
> Add DT bindings for the QUP GENI I2C controller on sa8255p platforms.
> 
> SA8255p platform abstracts resources such as clocks, interconnect and
> GPIO pins configuration in Firmware. SCMI power and perf protocol
> are utilized to request resource configurations.
> 
> SA8255p platform does not require the Serial Engine (SE) common properties
> as the SE firmware is loaded and managed by the TrustZone (TZ) secure
> environment.
> 
> Co-developed-by: Nikunj Kela <quic_nkela@quicinc.com>
> Signed-off-by: Nikunj Kela <quic_nkela@quicinc.com>
> Signed-off-by: Praveen Talari <praveen.talari@oss.qualcomm.com>

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>

Best regards,
Krzysztof

Re: [PATCH v2 10/12] i2c: qcom-geni: Use resources helper APIs in runtime PM functions

[kernel test robot]

Hi Praveen,

kernel test robot noticed the following build errors:

[auto build test ERROR on cc3aa43b44bdb43dfbac0fcb51c56594a11338a8]

url:    https://github.com/intel-lab-lkp/linux/commits/Praveen-Talari/soc-qcom-geni-se-Refactor-geni_icc_get-and-make-qup-memory-ICC-path-optional/20251229-130932
base:   cc3aa43b44bdb43dfbac0fcb51c56594a11338a8
patch link:    https://lore.kernel.org/r/20251229045446.3227667-11-praveen.talari%40oss.qualcomm.com
patch subject: [PATCH v2 10/12] i2c: qcom-geni: Use resources helper APIs in runtime PM functions
config: loongarch-allmodconfig (https://download.01.org/0day-ci/archive/20251231/202512311900.mG1XHHI2-lkp@intel.com/config)
compiler: clang version 19.1.7 (https://github.com/llvm/llvm-project cd708029e0b2869e80abe31ddb175f7c35361f90)
reproduce (this is a W=1 build): (https://download.01.org/0day-ci/archive/20251231/202512311900.mG1XHHI2-lkp@intel.com/reproduce)

If you fix the issue in a separate patch/commit (i.e. not just a new version of
the same patch/commit), kindly add following tags
| Reported-by: kernel test robot <lkp@intel.com>
| Closes: https://lore.kernel.org/oe-kbuild-all/202512311900.mG1XHHI2-lkp@intel.com/

All errors (new ones prefixed by >>, old ones prefixed by <<):

>> ERROR: modpost: "geni_se_resources_deactivate" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!
>> ERROR: modpost: "geni_se_resources_activate" [drivers/i2c/busses/i2c-qcom-geni.ko] undefined!

-- 
0-DAY CI Kernel Test Service
https://github.com/intel/lkp-tests/wiki