From: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
To: Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>
Cc: linux-arm-msm@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
Subject: [PATCH 2/3] arm64: dts: qcom: kaanapali: Add CCI definitions
Date: Fri, 08 May 2026 01:36:46 -0700 [thread overview]
Message-ID: <20260508-knp-camera-v1-2-a18e289163fd@oss.qualcomm.com> (raw)
In-Reply-To: <20260508-knp-camera-v1-0-a18e289163fd@oss.qualcomm.com>
Qualcomm Kaanapali SoC has three Camera Control Interface (CCI). Each
controller contains two I2C hosts.
Signed-off-by: Hangxiang Ma <hangxiang.ma@oss.qualcomm.com>
---
arch/arm64/boot/dts/qcom/kaanapali.dtsi | 282 ++++++++++++++++++++++++++++++++
1 file changed, 282 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/kaanapali.dtsi b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
index 9d8aee202797..ed7b7af6c43f 100644
--- a/arch/arm64/boot/dts/qcom/kaanapali.dtsi
+++ b/arch/arm64/boot/dts/qcom/kaanapali.dtsi
@@ -3339,6 +3339,96 @@ port@5 {
};
};
+ cci0: cci@941b000 {
+ compatible = "qcom,kaanapali-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0941b000 0x0 0x1000>;
+ interrupts = <GIC_SPI 426 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+ clocks = <&camcc CAM_CC_CAM_TOP_AHB_CLK>,
+ <&camcc CAM_CC_CCI_0_CLK>;
+ clock-names = "ahb", "cci";
+ pinctrl-0 = <&cci0_0_default &cci0_1_default>;
+ pinctrl-1 = <&cci0_0_sleep &cci0_1_sleep>;
+ pinctrl-names = "default", "sleep";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cci0_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci0_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci1: cci@941c000 {
+ compatible = "qcom,kaanapali-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0941c000 0x0 0x1000>;
+ interrupts = <GIC_SPI 427 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+ clocks = <&camcc CAM_CC_CAM_TOP_AHB_CLK>,
+ <&camcc CAM_CC_CCI_1_CLK>;
+ clock-names = "ahb", "cci";
+ pinctrl-0 = <&cci1_0_default &cci1_1_default>;
+ pinctrl-1 = <&cci1_0_sleep &cci1_1_sleep>;
+ pinctrl-names = "default", "sleep";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cci1_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci1_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
+ cci2: cci@941d000 {
+ compatible = "qcom,kaanapali-cci", "qcom,msm8996-cci";
+ reg = <0x0 0x0941d000 0x0 0x1000>;
+ interrupts = <GIC_SPI 428 IRQ_TYPE_EDGE_RISING>;
+ power-domains = <&camcc CAM_CC_TITAN_TOP_GDSC>;
+ clocks = <&camcc CAM_CC_CAM_TOP_AHB_CLK>,
+ <&camcc CAM_CC_CCI_2_CLK>;
+ clock-names = "ahb", "cci";
+ pinctrl-0 = <&cci2_0_default &cci2_1_default>;
+ pinctrl-1 = <&cci2_0_sleep &cci2_1_sleep>;
+ pinctrl-names = "default", "sleep";
+ status = "disabled";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ cci2_i2c0: i2c-bus@0 {
+ reg = <0>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ cci2_i2c1: i2c-bus@1 {
+ reg = <1>;
+ clock-frequency = <1000000>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+ };
+
camcc: clock-controller@956d000 {
compatible = "qcom,kaanapali-camcc";
reg = <0x0 0x0956d000 0x0 0x80000>;
@@ -3813,6 +3903,198 @@ tlmm: pinctrl@f100000 {
#interrupt-cells = <2>;
wakeup-parent = <&pdc>;
+ cci0_0_default: cci0-0-default-state {
+ sda-pins {
+ pins = "gpio109";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ scl-pins {
+ pins = "gpio110";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ cci0_0_sleep: cci0-0-sleep-state {
+ sda-pins {
+ pins = "gpio109";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio110";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci0_1_default: cci0-1-default-state {
+ sda-pins {
+ pins = "gpio111";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ scl-pins {
+ pins = "gpio112";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ cci0_1_sleep: cci0-1-sleep-state {
+ sda-pins {
+ pins = "gpio111";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio112";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci1_0_default: cci1-0-default-state {
+ sda-pins {
+ pins = "gpio113";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ scl-pins {
+ pins = "gpio114";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ cci1_0_sleep: cci1-0-sleep-state {
+ sda-pins {
+ pins = "gpio113";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio114";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci1_1_default: cci1-1-default-state {
+ sda-pins {
+ pins = "gpio107";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ scl-pins {
+ pins = "gpio160";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ cci1_1_sleep: cci1-1-sleep-state {
+ sda-pins {
+ pins = "gpio107";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio160";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci2_0_default: cci2-0-default-state {
+ sda-pins {
+ pins = "gpio108";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ scl-pins {
+ pins = "gpio149";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ cci2_0_sleep: cci2-0-sleep-state {
+ sda-pins {
+ pins = "gpio108";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio149";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
+ cci2_1_default: cci2-1-default-state {
+ sda-pins {
+ pins = "gpio115";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ scl-pins {
+ pins = "gpio116";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
+ cci2_1_sleep: cci2-1-sleep-state {
+ sda-pins {
+ pins = "gpio115";
+ function = "cci_i2c_sda";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+
+ scl-pins {
+ pins = "gpio116";
+ function = "cci_i2c_scl";
+ drive-strength = <2>;
+ bias-pull-down;
+ };
+ };
+
hub_i2c0_data_clk: hub-i2c0-data-clk-state {
/* SDA, SCL */
pins = "gpio66", "gpio67";
--
2.34.1
next prev parent reply other threads:[~2026-05-08 8:36 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-05-08 8:36 [PATCH 0/3] Add CCI and CAMSS support for Kaanapali Hangxiang Ma
2026-05-08 8:36 ` [PATCH 1/3] arm64: dts: qcom: kaanapali: Add camss node Hangxiang Ma
2026-05-08 10:45 ` Vladimir Zapolskiy
2026-05-08 8:36 ` Hangxiang Ma [this message]
2026-05-08 10:44 ` [PATCH 2/3] arm64: dts: qcom: kaanapali: Add CCI definitions Vladimir Zapolskiy
2026-05-08 8:36 ` [PATCH 3/3] arm64: dts: qcom: kaanapali: Add camera MCLK pinctrl Hangxiang Ma
2026-05-08 10:40 ` Vladimir Zapolskiy
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20260508-knp-camera-v1-2-a18e289163fd@oss.qualcomm.com \
--to=hangxiang.ma@oss.qualcomm.com \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox