* Re: [PATCH 2/2] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
2026-05-10 16:05 ` [PATCH 2/2] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
@ 2026-05-11 8:19 ` Neil Armstrong
2026-05-11 9:14 ` Konrad Dybcio
2026-05-11 9:19 ` Konrad Dybcio
1 sibling, 1 reply; 6+ messages in thread
From: Neil Armstrong @ 2026-05-11 8:19 UTC (permalink / raw)
To: azkali.limited, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Teguh Sobirin
Hi,
On 5/10/26 18:05, Alexandre Hamamdjian via B4 Relay wrote:
> From: Teguh Sobirin <teguh@sobir.in>
>
> Add initial device tree support for the Ayaneo Pocket DS gaming
> console based on the Qualcomm QCS8550 platform.
>
> The board file is split into qcs8550-ayaneo-pocket-common.dtsi and
> qcs8550-ayaneo-pocketds.dts in anticipation of additional boards in
> the same family that share the QCS8550 base. Only the Pocket DS has
> been verified on hardware so far; the shared dtsi is intended to pick
> up sibling boards as they are submitted.
Please don't, this is dead code, please send a single file and then
split it when you introduce variants boards.
>
> Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> ---
> arch/arm64/boot/dts/qcom/Makefile | 1 +
> .../dts/qcom/qcs8550-ayaneo-pocket-common.dtsi | 1596 ++++++++++++++++++++
> .../boot/dts/qcom/qcs8550-ayaneo-pocketds.dts | 170 +++
> 3 files changed, 1767 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index cc42829f92eb..45859e977bc9 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -185,6 +185,7 @@ qcs8300-ride-el2-dtbs := qcs8300-ride.dtb monaco-el2.dtbo
>
> dtb-$(CONFIG_ARCH_QCOM) += qcs8300-ride-el2.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs8550-aim300-aiot.dtb
> +dtb-$(CONFIG_ARCH_QCOM) += qcs8550-ayaneo-pocketds.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride.dtb
> dtb-$(CONFIG_ARCH_QCOM) += qcs9100-ride-r3.dtb
>
> diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-common.dtsi b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-common.dtsi
> new file mode 100644
> index 000000000000..8d215a9d31d5
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocket-common.dtsi
> @@ -0,0 +1,1596 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2025, Teguh Sobirin.
> + */
> +
> +#include <dt-bindings/leds/common.h>
> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
> +#include "qcs8550.dtsi"
> +#include "pm8550.dtsi"
> +#include "pm8550b.dtsi"
> +#define PMK8550VE_SID 5
> +#include "pm8550ve.dtsi"
> +#include "pm8550vs.dtsi"
> +#include "pmk8550.dtsi"
> +
> +/delete-node/ &aop_image_mem;
> +/delete-node/ &aop_config_mem;
> +/delete-node/ &camera_mem;
> +/delete-node/ &ipa_fw_mem;
> +/delete-node/ &ipa_gsi_mem;
> +/delete-node/ &mpss_dsm_mem;
> +/delete-node/ &mpss_mem;
> +/delete-node/ &q6_mpss_dtb_mem;
> +/delete-node/ &cdsp_mem;
> +/delete-node/ &q6_cdsp_dtb_mem;
> +
> +/delete-node/ &remoteproc_mpss;
> +/delete-node/ &remoteproc_cdsp;
> +
> +/ {
> + chassis-type = "handset";
> +
> + aliases {
> + serial0 = &uart7;
> + serial1 = &uart14;
> + hsuart0 = &uart11;
> + };
> +
> + chosen {
> + stdout-path = "serial0:115200n8";
> + };
> +
> + gpio-keys {
> + compatible = "gpio-keys";
> +
> + pinctrl-0 = <&volume_up_n>;
> + pinctrl-names = "default";
> +
> + key-volume-up {
> + label = "Volume Up";
> + debounce-interval = <15>;
> + gpios = <&pm8550_gpios 6 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_VOLUMEUP>;
> + linux,can-disable;
> + wakeup-source;
> + };
> + };
> +
> + pmic-glink {
> + compatible = "qcom,sm8550-pmic-glink", "qcom,pmic-glink";
> + #address-cells = <1>;
> + #size-cells = <0>;
> + orientation-gpios = <&tlmm 11 GPIO_ACTIVE_HIGH>;
> +
> + connector@0 {
> + compatible = "usb-c-connector";
> + reg = <0>;
> + power-role = "dual";
> + data-role = "dual";
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + pmic_glink_hs_in: endpoint {
> + remote-endpoint = <&usb_1_dwc3_hs>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + pmic_glink_ss_in: endpoint {
> + remote-endpoint = <&redriver_ss_out>;
> + };
> + };
> + };
> + };
> + };
> +
> + reserved-memory {
> + hyp_mem: hyp-region@80000000 {
> + reg = <0 0x80000000 0 0xa00000>;
> + no-map;
> + };
> +
> + cpusys_vm_mem: cpusys-vm-region@80a00000 {
> + reg = <0 0x80a00000 0 0x400000>;
> + no-map;
> + };
> +
> + hyp_tags_mem: hyp-tags-region@80e00000 {
> + reg = <0 0x80e00000 0 0x3d0000>;
> + no-map;
> + };
> +
> + xbl_sc_mem: xbl-sc-region@d8100000 {
> + reg = <0 0xd8100000 0 0x40000>;
> + no-map;
> + };
> +
> + hyp_tags_reserved_mem: hyp-tags-reserved-region@811d0000 {
> + reg = <0 0x811d0000 0 0x30000>;
> + no-map;
> + };
> +
> + xbl_dt_log_merged_mem: xbl-dt-log-merged-region@81a00000 {
> + reg = <0 0x81a00000 0 0x260000>;
> + no-map;
> + };
> +
> + aop_config_merged_mem: aop-config-merged-region@81c80000 {
> + reg = <0 0x81c80000 0 0x74000>;
> + no-map;
> + };
> +
> + chipinfo_mem: chipinfo-region@81cf4000 {
> + reg = <0 0x81cf4000 0 0x1000>;
> + no-map;
> + };
> +
> + global_sync_mem: global-sync-region@82600000 {
> + reg = <0 0x82600000 0 0x100000>;
> + no-map;
> + };
> +
> + tz_stat_mem: tz-stat-region@82700000 {
> + reg = <0 0x82700000 0 0x100000>;
> + no-map;
> + };
> +
> + cpucp_fw_mem: cpucp-fw-region@d8140000 {
> + reg = <0 0xd8140000 0 0x1c0000>;
> + no-map;
> + };
> +
> + qtee_mem: qtee-region@d8300000 {
> + reg = <0 0xd8300000 0 0x500000>;
> + no-map;
> + };
> +
> + hwfence_shbuf: hwfence-shbuf-region@e6440000 {
> + reg = <0 0xe6440000 0 0x2dd000>;
> + no-map;
> + };
> +
> + hyp_ext_reserved_mem: hyp-ext-reserved-region@ff700000 {
> + reg = <0 0xff700000 0 0x100000>;
> + no-map;
> + };
> +
> + llcc_lpi_mem: llcc_lpi_region@ff800000 {
> + reg = <0 0xff800000 0 0x600000>;
> + no-map;
> + };
> +
> + hyp_ext_tags_mem: hyp-ext-tags-region@fce00000 {
> + reg = <0 0xfce00000 0 0x2900000>;
> + no-map;
> + };
> +
> + splash_region: splash_region@b8000000 {
> + reg = <0x0 0xb8000000 0x0 0x2b00000>;
> + label = "cont_splash_region";
> + no-map;
> + };
> + };
> +
> + sound {
> + status = "okay";
> + compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
> + model = "SM8550-APS";
> + audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
> + "SpkrRight IN", "WSA_SPK2 OUT",
> + "VA DMIC0", "vdd-micb",
> + "VA DMIC1", "vdd-micb";
> +
> + wsa-dai-link {
> + link-name = "WSA Playback";
> +
> + cpu {
> + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
> + };
> +
> + codec {
> + sound-dai = <&spk_amp_l>,
> + <&spk_amp_r>,
> + <&swr0 0>,
> + <&lpass_wsamacro 0>;
> + };
> +
> + platform {
> + sound-dai = <&q6apm>;
> + };
> + };
> +
> + va-dai-link {
> + link-name = "VA Capture";
> +
> + cpu {
> + sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
> + };
> +
> + codec {
> + sound-dai = <&lpass_vamacro 0>;
> + };
> +
> + platform {
> + sound-dai = <&q6apm>;
> + };
> + };
> + };
> +
> + thermal-zones {
> + cpuss0-thermal {
Add labels for each thermal zones on the sm8550.dtsi files instead.
Please see the sm8650-ayaneo-pocket-s2 as reference.
> + polling-delay = <200>;
> + trips {
> + cpuss0_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
Bad alignment
Please add empty lines like the rest of the file.
> + cpuss0_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss0_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss0_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss0_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss0_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss0_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + cpuss1-thermal {
> + polling-delay = <200>;
> + trips {
> + cpuss1_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss1_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss1_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss1_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss1_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss1_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss1_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + cpuss2-thermal {
> + polling-delay = <200>;
> + trips {
> + cpuss2_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss2_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss2_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss2_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss2_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss2_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss2_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + cpuss3-thermal {
> + polling-delay = <200>;
> + trips {
> + cpuss3_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss3_fan1: trip-point3 {
> + temperature = <50000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss3_fan2: trip-point4 {
> + temperature = <60000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss3_fan3: trip-point5 {
> + temperature = <65000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss3_fan4: trip-point6 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss3_fan5: trip-point7 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpuss3_fan6: trip-point8 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + cpu7-top-thermal {
> + polling-delay = <200>;
> + trips {
> + cpu7_top_fan0: trip-point2 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpu7_top_fan1: trip-point3 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + cpu7_top_fan2: trip-point4 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-0-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss0_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss0_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss0_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-1-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss1_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss1_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss1_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-2-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss2_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss2_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss2_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-3-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss3_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss3_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss3_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-4-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss4_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss4_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss4_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-5-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss5_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss5_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss5_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-6-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss6_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss6_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss6_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + gpuss-7-thermal {
> + polling-delay = <200>;
> + trips {
> + gpuss7_fan0: trip-point3 {
> + temperature = <70000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss7_fan1: trip-point4 {
> + temperature = <75000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + gpuss7_fan2: trip-point5 {
> + temperature = <80000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
> + };
> +
> + };
> + };
> +
> + vdd_fan_5v0: vdd-fan-5v0-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_fan_5v0";
> +
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&fan_pwr_active>;
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vph_pwr: regulator-vph-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = " vph_pwr";
> + regulator-min-microvolt = <3700000>;
> + regulator-max-microvolt = <3700000>;
> +
> + regulator-always-on;
> + regulator-boot-on;
> + };
> +
> + pwm_fan: pwm-fan {
> + compatible = "pwm-fan";
> +
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&fan_pwm_active>, <&fan_int>;
> +
> + fan-supply = <&vdd_fan_5v0>;
> + pwms = <&pm8550_pwm 3 40000>;
> + interrupt-parent = <&tlmm>;
> + interrupts = <64 IRQ_TYPE_EDGE_FALLING>;
> +
> + #cooling-cells = <2>;
> + cooling-levels = <0 30 45 60 70 90 120 150>;
> + };
> +
> + wcn7850-pmu {
> + compatible = "qcom,wcn7850-pmu";
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&wlan_en>, <&bt_default>, <&pmk8550_sleep_clk>;
> +
> + wlan-enable-gpios = <&tlmm 80 GPIO_ACTIVE_HIGH>;
> + bt-enable-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>;
> +
> + vdd-supply = <&vreg_s5g_0p85>;
> + vddio-supply = <&vreg_l15b_1p8>;
> + vddaon-supply = <&vreg_s2g_0p85>;
> + vdddig-supply = <&vreg_s4e_0p95>;
> + vddrfa1p2-supply = <&vreg_s4g_1p25>;
> + vddrfa1p8-supply = <&vreg_s6g_1p86>;
> +
> + regulators {
> + vreg_pmu_rfa_cmn: ldo0 {
> + regulator-name = "vreg_pmu_rfa_cmn";
> + };
> +
> + vreg_pmu_aon_0p59: ldo1 {
> + regulator-name = "vreg_pmu_aon_0p59";
> + };
> +
> + vreg_pmu_wlcx_0p8: ldo2 {
> + regulator-name = "vreg_pmu_wlcx_0p8";
> + };
> +
> + vreg_pmu_wlmx_0p85: ldo3 {
> + regulator-name = "vreg_pmu_wlmx_0p85";
> + };
> +
> + vreg_pmu_btcmx_0p85: ldo4 {
> + regulator-name = "vreg_pmu_btcmx_0p85";
> + };
> +
> + vreg_pmu_rfa_0p8: ldo5 {
> + regulator-name = "vreg_pmu_rfa_0p8";
> + };
> +
> + vreg_pmu_rfa_1p2: ldo6 {
> + regulator-name = "vreg_pmu_rfa_1p2";
> + };
> +
> + vreg_pmu_rfa_1p8: ldo7 {
> + regulator-name = "vreg_pmu_rfa_1p8";
> + };
> +
> + vreg_pmu_pcie_0p9: ldo8 {
> + regulator-name = "vreg_pmu_pcie_0p9";
> + };
> +
> + vreg_pmu_pcie_1p8: ldo9 {
> + regulator-name = "vreg_pmu_pcie_1p8";
> + };
> + };
> + };
> +};
> +
> +/* DMIC 01 23 */
> +&lpass_vamacro {
> + pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
> + pinctrl-names = "default";
> + vdd-micb-supply = <&vreg_l10b_1p8>;
> + qcom,dmic-sample-rate = <4800000>;
> +};
> +
> +&apps_rsc {
> + regulators-0 {
> + compatible = "qcom,pm8550-rpmh-regulators";
> + qcom,pmic-id = "b";
> +
> + vdd-bob1-supply = <&vph_pwr>;
> + vdd-bob2-supply = <&vph_pwr>;
> + vdd-l1-l4-l10-supply = <&vreg_s6g_1p86>;
> + vdd-l2-l13-l14-supply = <&vreg_bob1>;
> + vdd-l3-supply = <&vreg_s4g_1p25>;
> + vdd-l5-l16-supply = <&vreg_bob1>;
> + vdd-l6-l7-supply = <&vreg_bob1>;
> + vdd-l8-l9-supply = <&vreg_bob1>;
> + vdd-l11-supply = <&vreg_s4g_1p25>;
> + vdd-l12-supply = <&vreg_s6g_1p86>;
> + vdd-l15-supply = <&vreg_s6g_1p86>;
> + vdd-l17-supply = <&vreg_bob2>;
> +
> + vreg_bob1: bob1 {
> + regulator-name = "vreg_bob1";
> + regulator-min-microvolt = <3296000>;
> + regulator-max-microvolt = <3960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_bob2: bob2 {
> + regulator-name = "vreg_bob2";
> + regulator-min-microvolt = <2720000>;
> + regulator-max-microvolt = <3960000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2b_3p0: ldo2 {
> + regulator-name = "vreg_l2b_3p0";
> + regulator-min-microvolt = <3008000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l5b_3p1: ldo5 {
> + regulator-name = "vreg_l5b_3p1";
> + regulator-min-microvolt = <3104000>;
> + regulator-max-microvolt = <3104000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l6b_1p8: ldo6 {
> + regulator-name = "vreg_l6b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l7b_1p8: ldo7 {
> + regulator-name = "vreg_l7b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l8b_1p8: ldo8 {
> + regulator-name = "vreg_l8b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l9b_2p9: ldo9 {
> + regulator-name = "vreg_l9b_2p9";
> + regulator-min-microvolt = <2960000>;
> + regulator-max-microvolt = <3008000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l10b_1p8: ldo10 {
> + regulator-name = "vreg_l10b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l11b_1p2: ldo11 {
> + regulator-name = "vreg_l11b_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l12b_1p8: ldo12 {
> + regulator-name = "vreg_l12b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l13b_3p0: ldo13 {
> + regulator-name = "vreg_l13b_3p0";
> + regulator-min-microvolt = <3000000>;
> + regulator-max-microvolt = <3000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l14b_3p2: ldo14 {
> + regulator-name = "vreg_l14b_3p2";
> + regulator-min-microvolt = <3200000>;
> + regulator-max-microvolt = <3200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l15b_1p8: ldo15 {
> + regulator-name = "vreg_l15b_1p8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l16b_2p8: ldo16 {
> + regulator-name = "vreg_l16b_2p8";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l17b_2p5: ldo17 {
> + regulator-name = "vreg_l17b_2p5";
> + regulator-min-microvolt = <2504000>;
> + regulator-max-microvolt = <2504000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-1 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "c";
> +
> + vdd-l1-supply = <&vreg_s4g_1p25>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4e_0p95>;
> +
> + vreg_l3c_0p9: ldo3 {
> + regulator-name = "vreg_l3c_0p9";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-2 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "d";
> +
> + vdd-l1-supply = <&vreg_s4e_0p95>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4e_0p95>;
> +
> + vreg_l1d_0p88: ldo1 {
> + regulator-name = "vreg_l1d_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <920000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-3 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "e";
> +
> + vdd-l1-supply = <&vreg_s4e_0p95>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4g_1p25>;
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> +
> + vreg_s4e_0p95: smps4 {
> + regulator-name = "vreg_s4e_0p95";
> + regulator-min-microvolt = <904000>;
> + regulator-max-microvolt = <984000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s5e_1p08: smps5 {
> + regulator-name = "vreg_s5e_1p08";
> + regulator-min-microvolt = <1010000>;
> + regulator-max-microvolt = <1120000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1e_0p88: ldo1 {
> + regulator-name = "vreg_l1e_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <880000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2e_0p9: ldo2 {
> + regulator-name = "vreg_l2e_0p9";
> + regulator-min-microvolt = <904000>;
> + regulator-max-microvolt = <970000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3e_1p2: ldo3 {
> + regulator-name = "vreg_l3e_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-4 {
> + compatible = "qcom,pm8550ve-rpmh-regulators";
> + qcom,pmic-id = "f";
> +
> + vdd-l1-supply = <&vreg_s4e_0p95>;
> + vdd-l2-supply = <&vreg_s4e_0p95>;
> + vdd-l3-supply = <&vreg_s4e_0p95>;
> + vdd-s4-supply = <&vph_pwr>;
> +
> + vreg_s4f_0p5: smps4 {
> + regulator-name = "vreg_s4f_0p5";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <700000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1f_0p9: ldo1 {
> + regulator-name = "vreg_l1f_0p9";
> + regulator-min-microvolt = <912000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l2f_0p88: ldo2 {
> + regulator-name = "vreg_l2f_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3f_0p88: ldo3 {
> + regulator-name = "vreg_l3f_0p88";
> + regulator-min-microvolt = <880000>;
> + regulator-max-microvolt = <912000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +
> + regulators-5 {
> + compatible = "qcom,pm8550vs-rpmh-regulators";
> + qcom,pmic-id = "g";
> + vdd-l1-supply = <&vreg_s4g_1p25>;
> + vdd-l2-supply = <&vreg_s4g_1p25>;
> + vdd-l3-supply = <&vreg_s4g_1p25>;
> + vdd-s1-supply = <&vph_pwr>;
> + vdd-s2-supply = <&vph_pwr>;
> + vdd-s3-supply = <&vph_pwr>;
> + vdd-s4-supply = <&vph_pwr>;
> + vdd-s5-supply = <&vph_pwr>;
> + vdd-s6-supply = <&vph_pwr>;
> +
> + vreg_s1g_1p25: smps1 {
> + regulator-name = "vreg_s1g_1p25";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1300000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s2g_0p85: smps2 {
> + regulator-name = "vreg_s2g_0p85";
> + regulator-min-microvolt = <800000>;
> + regulator-max-microvolt = <1000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s3g_0p8: smps3 {
> + regulator-name = "vreg_s3g_0p8";
> + regulator-min-microvolt = <300000>;
> + regulator-max-microvolt = <1004000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s4g_1p25: smps4 {
> + regulator-name = "vreg_s4g_1p25";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1352000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s5g_0p85: smps5 {
> + regulator-name = "vreg_s5g_0p85";
> + regulator-min-microvolt = <500000>;
> + regulator-max-microvolt = <1004000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_s6g_1p86: smps6 {
> + regulator-name = "vreg_s6g_1p86";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <2000000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l1g_1p2: ldo1 {
> + regulator-name = "vreg_l1g_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> +
> + vreg_l3g_1p2: ldo3 {
> + regulator-name = "vreg_l3g_1p2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
> + regulator-allow-set-load;
> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
> + RPMH_REGULATOR_MODE_HPM>;
> + };
> + };
> +};
> +
> +&pm8550_gpios {
> + sdc2_card_det_n: sdc2-card-det-n-state {
> + pins = "gpio12";
> + function = "normal";
> + input-enable;
> + output-disable;
> + bias-pull-up;
> + power-source = <1>;
> + };
> +
> + volume_up_n: volume-up-n-state {
> + pins = "gpio6";
> + function = "normal";
> + power-source = <1>;
> + bias-pull-up;
> + input-enable;
> + };
> +
> + fan_pwm_active: fan-pwm-active-state {
> + pins = "gpio9";
> + function = "func1";
> + output-low;
> + bias-disable;
> + power-source = <0>;
> + qcom,drive-strength = <3>; /* PMIC_GPIO_STRENGTH_LOW */
> + };
> +};
> +
> +&pmk8550_gpios {
> + pmk8550_sleep_clk: sleep-clk-state {
> + pins = "gpio3";
> + function = "func1";
> + input-disable;
> + output-enable;
> + bias-disable;
> + power-source = <0>;
> + };
> +};
> +
> +&pm8550b_eusb2_repeater {
> + vdd18-supply = <&vreg_l15b_1p8>;
> + vdd3-supply = <&vreg_l5b_3p1>;
> +};
> +
> +&pon_pwrkey {
> + status = "okay";
> +};
> +
> +&pon_resin {
> + linux,code = <KEY_VOLUMEDOWN>;
> +
> + status = "okay";
> +};
> +
> +&pmk8550_rtc {
> + nvmem-cells = <&rtc_offset>;
> + nvmem-cell-names = "offset";
> +};
> +
> +&pmk8550_sdam_2 {
> + rtc_offset: rtc-offset@bc {
> + reg = <0xbc 0x4>;
> + };
> +};
> +
> +&qupv3_id_0 {
> + status = "okay";
> +};
> +
> +&qupv3_id_1 {
> + status = "okay";
> +
> + /* AYANEO Controller serial interface */
> + uart11: serial@88c000 {
> + compatible = "qcom,geni-uart";
> + reg = <0 0x0088c000 0 0x4000>;
> + clock-names = "se";
> + clocks = <&gcc GCC_QUPV3_WRAP2_S3_CLK>;
> + pinctrl-names = "default";
> + pinctrl-0 = <&qup_uart11_default>;
> + interrupts = <GIC_SPI 585 IRQ_TYPE_LEVEL_HIGH 0>;
> + interconnects = <&clk_virt MASTER_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS
> + &clk_virt SLAVE_QUP_CORE_2 QCOM_ICC_TAG_ALWAYS>,
> + <&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
> + &config_noc SLAVE_QUP_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
> + interconnect-names = "qup-core", "qup-config";
> + operating-points-v2 = <&qup_opp_table_100mhz>;
> + power-domains = <&rpmhpd RPMHPD_CX>;
> + status = "okay";
> + };
> +};
> +
> +&remoteproc_adsp {
> + firmware-name = "qcom/sm8550/ayaneo/adsp.mdt",
> + "qcom/sm8550/ayaneo/adsp_dtb.mdt";
> + status = "okay";
> +};
> +
> +&sdhc_2 {
> + cd-gpios = <&pm8550_gpios 12 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default", "sleep";
> + pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
> + pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
> + vmmc-supply = <&vreg_l9b_2p9>;
> + vqmmc-supply = <&vreg_l8b_1p8>;
> + no-sdio;
> + no-mmc;
> +
> + sd-uhs-sdr12;
> + sd-uhs-sdr25;
> + sd-uhs-sdr50;
> + sd-uhs-sdr104;
> + sd-uhs-ddr50;
> +
> + qcom,dll-config = <0x0007442c>;
> + sdhci-caps-mask = <0x3 0x0>;
> +
> + status = "okay";
> +};
> +
> +&sleep_clk {
> + clock-frequency = <32764>;
> +};
> +
> +&swr0 {
> + status = "okay";
> +
> + spk_amp_l: speaker@0,0 {
> + compatible = "sdw20217020400";
> + reg = <0 0>;
> +
> + pinctrl-0 = <&spkr_1_sd_n_active>;
> + pinctrl-names = "default";
> +
> + powerdown-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
> +
> + vdd-1p8-supply = <&vreg_l10b_1p8>;
> + vdd-io-supply = <&vreg_l10b_1p8>;
> +
> + #sound-dai-cells = <0>;
> + sound-name-prefix = "SpkrLeft";
> + qcom,port-mapping = <1 2 3 7 10 13>;
> + };
> +
> + spk_amp_r: speaker@0,1 {
> + compatible = "sdw20217020400";
> + reg = <0 1>;
> +
> + pinctrl-0 = <&spkr_2_sd_n_active>;
> + pinctrl-names = "default";
> +
> + powerdown-gpios = <&tlmm 12 GPIO_ACTIVE_LOW>;
> +
> + vdd-1p8-supply = <&vreg_l10b_1p8>;
> + vdd-io-supply = <&vreg_l10b_1p8>;
> +
> + #sound-dai-cells = <0>;
> + sound-name-prefix = "SpkrRight";
> + qcom,port-mapping = <4 5 6 7 11 13>;
> + };
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <32 8>;
> +
> + bt_default: bt-default-state {
> + bt-en-pins {
> + pins = "gpio81";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + };
> +
> + sw-ctrl-pins {
> + pins = "gpio82";
> + function = "gpio";
> + bias-pull-down;
> + };
> + };
> +
> + fan_pwr_active: fan-pwr-active-state {
> + pins = "gpio31";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-low;
> + };
> +
> + fan_int: fan-int-state {
> + pins = "gpio64";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + };
> +
> + upd720201_active: upd720201-active-state {
> + pins = "gpio10", "gpio13", "gpio18";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-up;
> + output-high;
> + };
> +
> + gamepad_pwr_en: gamepad-pwr-en-active-state {
> + pins = "gpio52";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-disable;
> + output-high;
> + };
> +
> + qup_uart11_default: qup-uart11-default-state {
> + /* TX, RX */
> + pins = "gpio70", "gpio71";
> + function = "qup2_se3";
> + drive-strength = <2>;
> + bias-disable;
> + };
> +
> + sde_dsi_active: sde-dsi-active-state {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + output-high;
> + };
> +
> + sde_dsi_suspend: sde-dsi-suspend-state {
> + pins = "gpio133";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + sde_te_active: sde-te-active-state {
> + pins = "gpio86";
> + function = "mdp_vsync";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + sde_te_suspend: sde-te-suspend-state {
> + pins = "gpio86";
> + function = "mdp_vsync";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + wlan_en: wlan-en-state {
> + pins = "gpio80";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +
> + spkr_1_sd_n_active: spkr-1-sd-n-active-state {
> + pins = "gpio7";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> +
> + spkr_2_sd_n_active: spkr-2-sd-n-active-state {
> + pins = "gpio12";
> + function = "gpio";
> + drive-strength = <16>;
> + bias-disable;
> + output-high;
> + };
> +};
> +
> +&pm8550_pwm {
> + status = "okay";
> +};
> +
> +&xo_board {
> + clock-frequency = <76800000>;
> +};
> +
> +&gpi_dma1 {
> + status = "okay";
> +};
> +
> +&gpi_dma2 {
> + status = "okay";
> +};
> +
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
> + firmware-name = "qcom/sm8550/a740_zap.mbn";
> + };
> +};
> +
> +&gpu_opp_table {
> + /* Additional speedbin for Adreno A32
> + * 719000000 RPMH_REGULATOR_LEVEL_SVS_L2
> + * 746000000 RPMH_REGULATOR_LEVEL_NOM
> + * 794000000 RPMH_REGULATOR_LEVEL_NOM_L1
> + * 827000000 RPMH_REGULATOR_LEVEL_TURBO
> + * 860000000 RPMH_REGULATOR_LEVEL_TURBO_L1
> + * 1000000000 RPMH_REGULATOR_LEVEL_TURBO_L2
> + */
> + opp-719000000 {
> + opp-hz = /bits/ 64 <719000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
> + opp-peak-kBps = <10687500>; // Level 7
> + qcom,opp-acd-level = <0x882e5ffd>;
> + };
> +
> + opp-746000000 {
> + opp-hz = /bits/ 64 <746000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM>;
> + opp-peak-kBps = <10687500>; // Level 7
> + qcom,opp-acd-level = <0x882e5ffd>;
> + };
> +
> + opp-794000000 {
> + opp-hz = /bits/ 64 <794000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_NOM_L1>;
> + opp-peak-kBps = <14398438>; // Level 8
> + qcom,opp-acd-level = <0xa82d5ffd>;
> + };
> +
> + opp-827000000 {
> + opp-hz = /bits/ 64 <827000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO>;
> + opp-peak-kBps = <16500000>; // Level 9
> + qcom,opp-acd-level = <0xa82d5ffd>;
> + };
> +
> + opp-860000000 {
> + opp-hz = /bits/ 64 <860000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L1>;
> + opp-peak-kBps = <16500000>; // Level 9
> + qcom,opp-acd-level = <0x882d5ffd>;
> + };
> +
> + opp-1000000000 {
> + opp-hz = /bits/ 64 <1000000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_TURBO_L2>;
> + opp-peak-kBps = <16500000>; // Level 9
> + qcom,opp-acd-level = <0x882d5ffd>;
> + };
> +};
> +
> +&i2c_master_hub_0 {
> + status = "okay";
> +};
> +
> +&i2c_hub_2 {
> + status = "okay";
> +
> + typec-retimer@1c {
> + compatible = "onnn,nb7vpq904m";
> + reg = <0x1c>;
> + vcc-supply = <&vreg_l15b_1p8>;
> +
> + retimer-switch;
> + orientation-switch;
> +
> + ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + port@0 {
> + reg = <0>;
> +
> + redriver_ss_out: endpoint {
> + remote-endpoint = <&pmic_glink_ss_in>;
> + };
> + };
> +
> + port@1 {
> + reg = <1>;
> +
> + redriver_ss_in: endpoint {
> + data-lanes = <3 2 1 0>;
> + remote-endpoint = <&usb_dp_qmpphy_out>;
> + };
> + };
> + };
> + };
> +};
> +
> +&mdss {
> + status = "okay";
> +};
> +
> +&mdss_dsi0 {
> + vdda-supply = <&vreg_l3e_1p2>;
> + status = "okay";
> +
> + display_panel: panel@0 {
> + reg = <0>;
> +
> + pinctrl-0 = <&sde_dsi_active>, <&sde_te_active>;
> + pinctrl-1 = <&sde_dsi_suspend>, <&sde_te_suspend>;
> + pinctrl-names = "default", "sleep";
> + };
The panel compatible is not added in the main board file, this is wrong
and leaves a node without compatible.
I guess you did not test your DT files against the bindings
> +};
> +
> +&mdss_dsi0_phy {
> + vdds-supply = <&vreg_l1e_0p88>;
> + status = "okay";
> +};
> +
> +&mdss_dp0 {
> + status = "okay";
> +};
> +
> +&mdss_dp0_out {
> + data-lanes = <0 1>;
> +};
> +
> +&pcie0 {
> + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +
> + max-link-speed = <2>;
> +
> + pinctrl-0 = <&pcie0_default_state>;
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&pcie1 {
> + wake-gpios = <&tlmm 99 GPIO_ACTIVE_HIGH>;
> + perst-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
> +
> + pinctrl-0 = <&pcie1_default_state>, <&upd720201_active>, <&gamepad_pwr_en>;
This is wrong, please add an upd720201 node like the ayaneo pocket s2
> + pinctrl-names = "default";
> +
> + status = "okay";
> +};
> +
> +&pcie1_phy {
> + vdda-phy-supply = <&vreg_l3c_0p9>;
> + vdda-pll-supply = <&vreg_l3e_1p2>;
> + vdda-qref-supply = <&vreg_l1e_0p88>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_hc {
> + reset-gpios = <&tlmm 210 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l17b_2p5>;
> + vcc-max-microamp = <1300000>;
> + vccq-supply = <&vreg_l1g_1p2>;
> + vccq-max-microamp = <1200000>;
> + vdd-hba-supply = <&vreg_l3g_1p2>;
> +
> + status = "okay";
> +};
> +
> +&ufs_mem_phy {
> + vdda-phy-supply = <&vreg_l1d_0p88>;
> + vdda-pll-supply = <&vreg_l3e_1p2>;
> +
> + status = "okay";
> +};
> +
> +&usb_1 {
> + status = "okay";
> +};
> +
> +&usb_1_dwc3_hs {
> + remote-endpoint = <&pmic_glink_hs_in>;
> +};
> +
> +&usb_1_hsphy {
> + vdd-supply = <&vreg_l1e_0p88>;
> + vdda12-supply = <&vreg_l3e_1p2>;
> +
> + phys = <&pm8550b_eusb2_repeater>;
> +
> + status = "okay";
> +};
> +
> +&usb_dp_qmpphy {
> + vdda-phy-supply = <&vreg_l3e_1p2>;
> + vdda-pll-supply = <&vreg_l3f_0p88>;
> +
> + status = "okay";
> +};
> +
> +&usb_dp_qmpphy_out {
> + remote-endpoint = <&redriver_ss_in>;
> +};
> +
> +&uart7 {
> + status = "okay";
> +};
> +
> +&uart14 {
> + status = "okay";
> +
> + bluetooth {
> + compatible = "qcom,wcn7850-bt";
> +
> + vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
> + vddaon-supply = <&vreg_pmu_aon_0p59>;
> + vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
> + vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
> + vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
> + vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
> + vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
> +
> + max-speed = <3200000>;
> + };
> +};
> +
> +&iris {
> + status = "okay";
> +};
> diff --git a/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocketds.dts b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocketds.dts
> new file mode 100644
> index 000000000000..723b027fa73b
> --- /dev/null
> +++ b/arch/arm64/boot/dts/qcom/qcs8550-ayaneo-pocketds.dts
> @@ -0,0 +1,170 @@
> +// SPDX-License-Identifier: BSD-3-Clause
> +/*
> + * Copyright (c) 2025, Teguh Sobirin.
> + * Copyright (c) 2025, ROCKNIX (https://github.com/ROCKNIX)
> + */
> +
> +/dts-v1/;
> +
> +#include "qcs8550-ayaneo-pocket-common.dtsi"
> +
> +/ {
> + model = "AYANEO Pocket DS";
> + compatible = "ayaneo,pocketds", "qcom,sm8550";
> + rocknix-u-boot-dt-id = "u-boot-pocket-ds";
> +
> + tca6424_vcc: regulator-tca6424-vcc {
> + compatible = "regulator-fixed";
> + regulator-name = "tca6424_vcc";
> +
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> +
> + gpio = <&tlmm 168 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + regulator-boot-on;
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vdd_ts: vdd-ts {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_ts_en";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + gpio = <&tca6408 1 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> + };
> +
> +};
> +
> +&tlmm {
> + gpio-reserved-ranges = <32 4>;
> + panel_pwr_active: panel-pwr-active-state {
> + pins = "gpio152", "gpio153";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + output-high;
> + };
> +
> + sde_dsi1_active: sde-dsi1-active-state {
> + pins = "gpio137";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + output-high;
> + };
> +
> + sde_dsi1_suspend: sde-dsi1-suspend-state {
> + pins = "gpio137";
> + function = "gpio";
> + drive-strength = <2>;
> + bias-pull-down;
> + };
> +
> + ts_rst_default: ts-rst-default-state {
> + pins = "gpio24";
> + function = "gpio";
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + ts_rst_sleep: ts-rst-sleep-state {
> + pins = "gpio24";
> + function = "gpio";
> + bias-pull-down;
> + drive-strength = <2>;
> + };
> +
> + ts_int_default: ts-int-default-state {
> + pins = "gpio25";
> + function = "gpio";
> + bias-pull-up;
> + drive-strength = <8>;
> + };
> +
> + ts_int_sleep: ts-int-sleep-state {
> + pins = "gpio25";
> + function = "gpio";
> + bias-pull-down;
> + drive-strength = <2>;
> + };
> +
> + ts2_irq: ts2-irq-state {
> + pins = "gpio39";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-disable;
> + };
> +
> + ts2_reset: ts2-reset-state {
> + pins = "gpio38";
> + function = "gpio";
> + drive-strength = <8>;
> + bias-pull-down;
> + };
> +};
> +
> +&i2c0 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + tca6408: tca64_20@20 {
> + gpio-controller;
> + compatible = "ti,tca6408";
> + status = "okay";
> + reg = <0x20>;
> + #gpio-cells = <0x02>;
> + vcc-supply = <&tca6424_vcc>;
> + };
> +};
> +
> +&i2c2 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen@5d {
> + reg = <0x5d>;
> + compatible = "goodix,gt911";
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
> +
> + reset-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
> + irq-gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
> + VDDIO-supply = <&vdd_ts>;
> +
> + touchscreen-size-x = <768>;
> + touchscreen-size-y = <1024>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&ts2_reset>, <&ts2_irq>;
> +
> + };
> +};
> +
> +&i2c4 {
> + clock-frequency = <400000>;
> + status = "okay";
> + touchscreen: touchscreen@38 {
> + compatible = "focaltech,ft5426";
> + reg = <0x38>;
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <25 IRQ_TYPE_EDGE_FALLING>;
> +
> + reset-gpios = <&tlmm 24 GPIO_ACTIVE_LOW>;
> +
> + vcc-supply = <&vreg_l14b_3p2>;
> + iovcc-supply = <&vreg_l12b_1p8>;
> +
> + pinctrl-0 = <&ts_int_default &ts_rst_default>;
> + pinctrl-1 = <&ts_int_sleep &ts_rst_sleep>;
> + pinctrl-names = "default", "sleep";
> +
> + touchscreen-size-x = <1080>;
> + touchscreen-size-y = <1920>;
> + };
> +};
>
Why 2 touch controllers ?
Thanks,
Neil
^ permalink raw reply [flat|nested] 6+ messages in thread* Re: [PATCH 2/2] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console
2026-05-10 16:05 ` [PATCH 2/2] arm64: dts: qcom: add basic devicetree for Ayaneo Pocket DS gaming console Alexandre Hamamdjian via B4 Relay
2026-05-11 8:19 ` Neil Armstrong
@ 2026-05-11 9:19 ` Konrad Dybcio
1 sibling, 0 replies; 6+ messages in thread
From: Konrad Dybcio @ 2026-05-11 9:19 UTC (permalink / raw)
To: azkali.limited, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Teguh Sobirin
On 5/10/26 6:05 PM, Alexandre Hamamdjian via B4 Relay wrote:
> From: Teguh Sobirin <teguh@sobir.in>
>
> Add initial device tree support for the Ayaneo Pocket DS gaming
> console based on the Qualcomm QCS8550 platform.
>
> The board file is split into qcs8550-ayaneo-pocket-common.dtsi and
> qcs8550-ayaneo-pocketds.dts in anticipation of additional boards in
> the same family that share the QCS8550 base. Only the Pocket DS has
> been verified on hardware so far; the shared dtsi is intended to pick
> up sibling boards as they are submitted.
>
> Co-developed-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> Signed-off-by: Alexandre Hamamdjian <azkali.limited@gmail.com>
> Signed-off-by: Teguh Sobirin <teguh@sobir.in>
> ---
[...]
> + splash_region: splash_region@b8000000 {
underscores in node names are frowned upon
> + reg = <0x0 0xb8000000 0x0 0x2b00000>;
> + label = "cont_splash_region";
Is this label any useful?
> + no-map;
> + };
> + };
> +
> + sound {
> + status = "okay";
It's already 'okay' if previously not disabled, please drop this line
> + compatible = "qcom,sm8550-sndcard", "qcom,sm8450-sndcard";
> + model = "SM8550-APS";
> + audio-routing = "SpkrLeft IN", "WSA_SPK1 OUT",
> + "SpkrRight IN", "WSA_SPK2 OUT",
> + "VA DMIC0", "vdd-micb",
> + "VA DMIC1", "vdd-micb";
> +
> + wsa-dai-link {
> + link-name = "WSA Playback";
> +
> + cpu {
'co'dec < 'cp'u < 'p'latform
> + sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
> + };
> +
> + codec {
> + sound-dai = <&spk_amp_l>,
> + <&spk_amp_r>,
> + <&swr0 0>,
> + <&lpass_wsamacro 0>;
Please align these entries
[...]
> + thermal-zones {
> + cpuss0-thermal {
You should really be overriding nodes by &labels, this is fragile as-is,
since even if someone deletes the thermal zone nodes, DTC will happily
compile this (and it won't work)
> + polling-delay = <200>;
> + trips {
Let's add an \n between the last property and the followng subnodes
> + cpuss0_fan0: trip-point2 {
> + temperature = <40000>;
> + hysteresis = <3000>;
> + type = "passive";
> + };
Please remove the extra \t here and separate subsequent nodes
with a \n
[...]
> + vdd_fan_5v0: vdd-fan-5v0-regulator {
> + compatible = "regulator-fixed";
> + regulator-name = "vdd_fan_5v0";
> +
> + regulator-min-microvolt = <5000000>;
> + regulator-max-microvolt = <5000000>;
> +
> + gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
> + enable-active-high;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&fan_pwr_active>;
property-n
property-names
file-wide, please
> +
> + regulator-state-mem {
> + regulator-off-in-suspend;
> + };
> + };
> +
> + vph_pwr: regulator-vph-pwr {
> + compatible = "regulator-fixed";
> + regulator-name = " vph_pwr";
stray spaces after "
> +&gpu {
> + status = "okay";
> +
> + zap-shader {
Please use the &gpu_zap_shader label to override
> + firmware-name = "qcom/sm8550/a740_zap.mbn";
> + };
> +};
> +
> +&gpu_opp_table {
> + /* Additional speedbin for Adreno A32
> + * 719000000 RPMH_REGULATOR_LEVEL_SVS_L2
> + * 746000000 RPMH_REGULATOR_LEVEL_NOM
> + * 794000000 RPMH_REGULATOR_LEVEL_NOM_L1
> + * 827000000 RPMH_REGULATOR_LEVEL_TURBO
> + * 860000000 RPMH_REGULATOR_LEVEL_TURBO_L1
> + * 1000000000 RPMH_REGULATOR_LEVEL_TURBO_L2
> + */
> + opp-719000000 {
> + opp-hz = /bits/ 64 <719000000>;
> + opp-level = <RPMH_REGULATOR_LEVEL_SVS_L2>;
> + opp-peak-kBps = <10687500>; // Level 7
Let's drop these inline comments
[...]
> +&mdss_dsi0 {
> + vdda-supply = <&vreg_l3e_1p2>;
> + status = "okay";
Please keep an \n before 'status'
[...]
> +&mdss_dp0_out {
> + data-lanes = <0 1>;
> +};
Only 2 lanes? Are the other 2 not wired up?
> +
> +&pcie0 {
> + wake-gpios = <&tlmm 96 GPIO_ACTIVE_HIGH>;
> + perst-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>;
> +
> + max-link-speed = <2>;
Are there issues with Gen3-speed links?
[...]
> +&i2c2 {
> + clock-frequency = <400000>;
> + status = "okay";
> +
> + touchscreen@5d {
> + reg = <0x5d>;
> + compatible = "goodix,gt911";
> +
> + interrupt-parent = <&tlmm>;
> + interrupts = <39 IRQ_TYPE_EDGE_FALLING>;
> +
> + reset-gpios = <&tlmm 38 GPIO_ACTIVE_HIGH>;
> + irq-gpios = <&tlmm 39 GPIO_ACTIVE_HIGH>;
> + VDDIO-supply = <&vdd_ts>;
> +
> + touchscreen-size-x = <768>;
> + touchscreen-size-y = <1024>;
> +
> + pinctrl-names = "default";
> + pinctrl-0 = <&ts2_reset>, <&ts2_irq>;
> +
> + };
Stray \n above
Does userspace somehow map these touchpanels to the right display,
or do you need to bind them somehow?
Konrad
^ permalink raw reply [flat|nested] 6+ messages in thread