Re: [PATCH v5 4/4] PCI: dwc: Add support for configuring lane equalization presets

[Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>]

On 28.01.2025 10:37 AM, Krishna Chaitanya Chundru wrote:
> PCIe equalization presets are predefined settings used to optimize
> signal integrity by compensating for signal loss and distortion in
> high-speed data transmission.
> 
> Based upon the number of lanes and the data rate supported, write
> the preset data read from the device tree in to the lane equalization
> control registers.
> 
> Signed-off-by: Krishna Chaitanya Chundru <krishna.chundru@oss.qualcomm.com>
> ---
>  drivers/pci/controller/dwc/pcie-designware-host.c | 41 +++++++++++++++++++++++
>  drivers/pci/controller/dwc/pcie-designware.h      |  3 ++
>  include/uapi/linux/pci_regs.h                     |  3 ++
>  3 files changed, 47 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index 2cd0acbf9e18..f458b4c70053 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -507,6 +507,10 @@ int dw_pcie_host_init(struct dw_pcie_rp *pp)
>  	if (pci->num_lanes < 1)
>  		pci->num_lanes = dw_pcie_link_get_max_link_width(pci);
>  
> +	ret = of_pci_get_equalization_presets(dev, &pp->presets, pci->num_lanes);
> +	if (ret)
> +		goto err_free_msi;
> +
>  	/*
>  	 * Allocate the resource for MSG TLP before programming the iATU
>  	 * outbound window in dw_pcie_setup_rc(). Since the allocation depends
> @@ -802,6 +806,42 @@ static int dw_pcie_iatu_setup(struct dw_pcie_rp *pp)
>  	return 0;
>  }
>  
> +static void dw_pcie_program_presets(struct dw_pcie *pci, u8 cap_id, u8 lane_eq_offset,
> +				    u8 lane_reg_size, u8 *presets, u8 num_lanes)
> +{
> +	u32 cap;
> +	int i;
> +
> +	cap = dw_pcie_find_ext_capability(pci, cap_id);
> +	if (!cap)
> +		return;
> +
> +	/*
> +	 * Write preset values to the registers byte-by-byte for the given
> +	 * number of lanes and register size.
> +	 */
> +	for (i = 0; i < num_lanes * lane_reg_size; i++)
> +		dw_pcie_writeb_dbi(pci, cap + lane_eq_offset + i, presets[i]);
> +}
> +
> +static void dw_pcie_config_presets(struct dw_pcie_rp *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	enum pci_bus_speed speed = pcie_link_speed[pci->max_link_speed];
> +
> +	/* For data rate of 8 GT/S each lane equalization control is 16bits wide */
> +	if (speed >= PCIE_SPEED_8_0GT && pp->presets.eq_presets_8gts[0] != PCI_EQ_RESV)
> +		dw_pcie_program_presets(pci, PCI_EXT_CAP_ID_SECPCI, PCI_SECPCI_LE_CTRL,
> +					0x2, (u8 *)pp->presets.eq_presets_8gts, pci->num_lanes);

If you move the != RESERVED into dw_pcie_program_presets, this becomes more readable

otherwise, this looks good

Konrad