[PATCH] arm64: dts: qcom: sm6115: add debug UART pins

[PATCH] arm64: dts: qcom: sm6115: add debug UART pins

[Bartosz Golaszewski]

From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>

We should not rely on the bootloader to set up the pinmux of the debug
UART port. Let's add pin definitions for uart4 to tlmm and bind them to
the relevant device node.

Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
---
 arch/arm64/boot/dts/qcom/sm6115.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6115.dtsi b/arch/arm64/boot/dts/qcom/sm6115.dtsi
index c8865779173ec..91fc36b59abf9 100644
--- a/arch/arm64/boot/dts/qcom/sm6115.dtsi
+++ b/arch/arm64/boot/dts/qcom/sm6115.dtsi
@@ -721,6 +721,13 @@ qup_spi5_default: qup-spi5-default-state {
 				bias-pull-up;
 			};
 
+			qup_uart4_default: qup-uart4-default-state {
+				pins = "gpio12", "gpio13";
+				function = "qup4";
+				drive-strength = <2>;
+				bias-disable;
+			};
+
 			sdc1_state_on: sdc1-on-state {
 				clk-pins {
 					pins = "sdc1_clk";
@@ -1565,6 +1572,8 @@ uart4: serial@4a90000 {
 				reg = <0x0 0x04a90000 0x0 0x4000>;
 				clock-names = "se";
 				clocks = <&gcc GCC_QUPV3_WRAP0_S4_CLK>;
+				pinctrl-names = "default";
+				pinctrl-0 = <&qup_uart4_default>;
 				interrupts = <GIC_SPI 331 IRQ_TYPE_LEVEL_HIGH>;
 				interconnects = <&clk_virt MASTER_QUP_CORE_0 RPM_ALWAYS_TAG
 						 &clk_virt SLAVE_QUP_CORE_0 RPM_ALWAYS_TAG>,
-- 
2.48.1

Re: [PATCH] arm64: dts: qcom: sm6115: add debug UART pins

[Konrad Dybcio]

On 6/25/25 5:28 PM, Bartosz Golaszewski wrote:
> From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> 
> We should not rely on the bootloader to set up the pinmux of the debug
> UART port. Let's add pin definitions for uart4 to tlmm and bind them to
> the relevant device node.
> 
> Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>

Konrad

Re: [PATCH] arm64: dts: qcom: sm6115: add debug UART pins

[Bartosz Golaszewski]

On Fri, Jun 27, 2025 at 5:09 PM Konrad Dybcio
<konrad.dybcio@oss.qualcomm.com> wrote:
>
> On 6/25/25 5:28 PM, Bartosz Golaszewski wrote:
> > From: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> >
> > We should not rely on the bootloader to set up the pinmux of the debug
> > UART port. Let's add pin definitions for uart4 to tlmm and bind them to
> > the relevant device node.
> >
> > Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
> > ---
>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
>
> Konrad

We're late into rc5 so gentle ping, any chance we could get this
queued for v6.17?

Bartosz